KEMX-2030
Industrial Motherboard in Mini-ITX form factor
with Intel® Atom N270
User’s Guide
KEMX-2030 User’s Manual
I
Content
Content
Content.......................................................................................................................3
Figures .......................................................................................................................5
Tables......................................................................................................................... 6
Safety Instructions......................................................................................................8
Before You Begin......................................................................................8
Preface..................................................................................................................... 11
Unpacking .............................................................................................. 11
Warranty Policy ...................................................................................... 12
Chapter 1 Introduction ........................................................................................... 16
Overview ................................................................................................ 16
Product Specifications............................................................................ 17
Chapter 2 Hardware Settings ................................................................................ 20
Overview ................................................................................................ 20
Jumper Settings......................................................................................... 22
Chapter 3 System Installation................................................................................ 37
Expansive Interfaces.............................................................................. 37
Chapter 4 AMI BIOS Setup.................................................................................... 39
Overview ................................................................................................ 39
Main Menu.............................................................................................. 40
Advanced Menu ..................................................................................... 41
Boot Menu.............................................................................................. 45
Chipset Menu ......................................................................................... 46
Power Menu ........................................................................................... 48
KEMX-2030 User’s Manual
3
Content
Security Menu ........................................................................................ 49
Exit Menu ............................................................................................... 50
Chapter 5 Driver Installation .................................................................................. 52
Appendix A System Resources.............................................................................. 53
Appendix B DIO (Digital I/O) KIT User Guide........................................................... 56
KEMX-2030 User’s Manual
4
Figures
Figures
Figure 1 Block Diagram ............................................................................. 18
Figure 3 Jumper Connector ....................................................................... 20
Figure 5 Rear Panel IO.............................................................................. 24
Figure 6 Expansive Interfaces.................................................................... 37
KEMX-2030 User’s Manual
5
Tables
Table 36 PCI1, PCI slots ............................................................................ 35
Table 38 Parallel Port Wafer ...................................................................... 36
Table 39 BIOS Main Menu ......................................................................... 40
Table 41 System Information...................................................................... 41
Table 42 Advanced Menu........................................................................... 41
Table 45 Trusted Computing ...................................................................... 44
Table 47 Boot Menu................................................................................... 45
Table 48 Chipset Menu .............................................................................. 46
Table 50 Power Menu ................................................................................ 48
Table 51 Security Menu ............................................................................. 49
Table 52 Exit Menu .................................................................................... 50
KEMX-2030 User’s Manual
7
Safety Instructions
Safety Instructions
„ Before You Begin
Before handling the product, read the instructions and safety guidelines on the
following pages to prevent damage to the product and to ensure your own personal
safety. Refer to the “Advisories” section in the Preface for advisory conventions used
in this user’s guide, including the distinction between Warnings, Cautions, Important
Notes, and Notes.
„
Always use caution when handling/operating a computer. Only qualified,
experienced, authorized electronics service personnel should access the
interior of a computer. The power supplies produce high voltages and
energy hazards, which can cause bodily harm.
„
Use extreme caution when installing or removing components. Refer to the
installation instructions in this user’s guide for precautions and procedures.
If you have any questions, please contact Quanmax Post-Sales Technical
Support.
WARNING
High voltages are present inside the chassis when the unit’s power cord is
plugged into an electrical outlet. Turn off system power, turn off the power
supply, and then disconnect the power cord from its source before
removing the chassis cover. Turning off the system power switch does not
remove power to components.
„ When Working Inside a Computer
Before taking covers off a computer, perform the following steps:
1. Turn off the computer and any peripherals.
2. Disconnect the computer and peripherals from their power sources or
subsystems to prevent electric shock or system board damage. This does not
apply when hot swapping parts.
KEMX-2030 User’s Manual
8
Safety Instructions
3. Follow the guidelines provided in “Preventing Electrostatic Discharge” on the
following page.
4. Disconnect any telephone or telecommunications lines from the computer.
In addition, take note of these safety guidelines when appropriate:
„
„
To help avoid possible damage to system boards, wait five seconds after
turning off the computer before removing a component, removing a system
board, or disconnecting a peripheral device from the computer.
When you disconnect a cable, pull on its connector or on its strain-relief loop,
not on the cable itself. Some cables have a connector with locking tabs. If you
are disconnecting this type of cable, press in on the locking tabs before
disconnecting the cable. As you pull connectors apart, keep them evenly
aligned to avoid bending any connector pins. Also, before connecting a cable,
make sure both connectors are correctly oriented and aligned.
CAUTION
Do not attempt to service the system yourself except as explained in this
user’s guide. Follow installation and troubleshooting instructions closely.
„ Preventing Electrostatic Discharge
Static electricity can harm system boards. Perform service at an ESD workstation
and follow proper ESD procedure to reduce the risk of damage to components.
Quanmax strongly encourages you to follow proper ESD procedure, which can
include wrist straps and smocks, when servicing equipment.
You can also take the following steps to prevent damage from electrostatic
discharge (ESD):
„
When unpacking a static-sensitive component from its shipping carton, do not
remove the component’s antistatic packing material until you are ready to install
the component in a computer. Just before unwrapping the antistatic packaging,
be sure you are at an ESD workstation or grounded. This will discharge any
static electricity that may have built up in your body.
„
When transporting a sensitive component, first place it in an antistatic container
KEMX-2030 User’s Manual
9
Safety Instructions
or packaging.
„
„
„
Handle all sensitive components at an ESD workstation. If possible, use
antistatic floor pads and workbench pads.
Handle components and boards with care. Don’t touch the components or
contacts on a board. Hold a board by its edges or by its metal mounting bracket.
Do not handle or store system boards near strong electrostatic, electromagnetic,
magnetic, or radioactive fields.
KEMX-2030 User’s Manual
10
Preface
Preface
„ How to Use This Guide
This guide is designed to be used as step-by-step instructions for installation, and as
a reference for operation, troubleshooting, and upgrades.
NOTE
Driver downloads and additional information are available under
„ Unpacking
When unpacking, follow these steps:
1. After opening the box, save it and the packing material for possible future
shipment.
2. Remove all items from the box. If any items listed on the purchase order
are missing, notify Quanmax customer service immediately.
3. Inspect the product for damage. If there is damage, notify Quanmax
customer service immediately. Refer to “Warranty Policy” for the return
procedure.
„ Regulatory Compliance Statements
This section provides the FCC compliance statement for Class A devices.
FCC Compliance Statement for Class A Devices
The product(s) described in this user’s guide has been tested and found to comply
with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the user’s guide, may cause harmful
interference to radio communications. Operation of this equipment in a residential
KEMX-2030 User’s Manual
11
Preface
area (domestic environment) is likely to cause harmful interference, in which case
the user will be required to correct the interference (take adequate measures) at
their own expense.
Changes or modifications not expressly approved by Quanmax could void the user's
authority to operate the equipment.
NOTE
The assembler of a personal computer system may be required to test
the system and/or make necessary modifications if a system is found to
cause harmful interference or to be noncompliant with the appropriate
standards for its intended use.
„ Warranty Policy
Limited Warranty
Quanmax Inc.’s detailed Limited Warranty policy can be found under Support at
The limited warranty is void if the product has been subjected to alteration, neglect,
misuse, or abuse; if any repairs have been attempted by anyone other than
Quanmax or its authorized agent; or if the failure is caused by accident, acts of God,
or other causes beyond the control of Quanmax or the manufacturer. Neglect,
misuse, and abuse shall include any installation, operation, or maintenance of the
product other than in accordance with the user’s guide.
No agent, dealer, distributor, service company, or other party is authorized to change,
modify, or extend the terms of this Limited Warranty in any manner whatsoever.
Quanmax reserves the right to make changes or improvements in any product
without incurring any obligation to similarly alter products previously purchased.
Return Procedure
login to obtain a Return Material Authorization (RMA) Number. If you do not have an
account, send an email to [email protected] to apply for one.
All product(s) returned to Quanmax for service or credit must be accompanied by a
Return Material Authorization (RMA) Number. Freight on all returned items must be
prepaid by the customer who is responsible for any loss or damage caused by
common carrier in transit. Returns for Warranty must include a Failure Report for
each unit, by serial number(s), as well as a copy of the original invoice showing the
KEMX-2030 User’s Manual
12
Preface
date of purchase.
To reduce risk of damage, returns of product must be in a Quanmax shipping
container. If the original container has been lost or damaged, new shipping
containers may be obtained from Quanmax Customer Service at a nominal cost.
Quanmax owns all parts removed from repaired products. Quanmax uses new and
reconditioned parts made by various manufacturers in performing warranty repairs
and building replacement products. If Quanmax repairs or replaces a product, its
warranty term is not extended.
Shipments not in compliance with this Limited Warranty Return Policy will not be
accepted by Quanmax.
Limitation of Liability
In no event shall Quanmax be liable for any defect in hardware, software, loss, or
inadequacy of data of any kind, or for any direct, indirect, incidental, or
consequential damages in connection with or arising out of the performance or use
of any product furnished hereunder. Quanmax’s liability shall in no event exceed the
purchase price of the product purchased hereunder. The foregoing limitation of
liability shall be equally applicable to any service provided by Quanmax or its
authorized agent.
„ Maintaining Your Computer
Environmental Factors
„
Temperature
The ambient temperature within an enclosure may be greater than room
ambient temperature. Installation in an enclosure should be such that the
amount of air flow required for safe operation is not compromised.
Consideration should be given to the maximum rated ambient temperature.
Overheating can cause a variety of problems, including premature aging and
failure of chips or mechanical failure of devices.
If the system has been exposed to abnormally cold temperatures, allow a
two-hour warm-up period to bring it up to normal operating temperature before
turning it on. Failure to do so may cause damage to internal components,
particularly the hard disk drive.
„
Humidity
High-humidity can cause moisture to enter and accumulate in the system. This
moisture can cause corrosion of internal components and degrade such
KEMX-2030 User’s Manual
13
Preface
properties as electrical resistance and thermal conductivity. Extreme moisture
buildup inside the system can result in electrical shorts, which can cause
serious damage to the system.
Buildings in which climate is controlled usually maintain an acceptable level of
humidity for system equipment. However, if a system is located in an unusually
humid location, a dehumidifier can be used to maintain the humidity within an
acceptable range. Refer to the “Specifications” section of this user’s guide for
the operating and storage humidity specifications.
„
Altitude
Operating a system at a high altitude (low pressure) reduces the efficiency of
the cooling fans to cool the system. This can cause electrical problems related
to arcing and corona effects. This condition can also cause sealed components
with internal pressure, such as electrolytic capacitors, to fail or perform at
reduced efficiency.
Power Protection
The greatest threats to a system’s supply of power are power loss, power spikes,
and power surges caused by electrical storms, which interrupt system operation
and/or damage system components. To protect your system, always properly
ground power cables and one of the following devices.
„
Surge Protector
Surge protectors are available in a variety of types and usually provide a level
of protection proportional with the cost of the device. Surge protectors prevent
voltage spikes from entering a system through the AC power cord. Surge
protectors, however, do not offer protection against brownouts, which occur
when the voltage drops more than 20 percent below the normal AC line voltage
level.
„
Line Conditioner
Line conditioners go beyond the over voltage protection of surge protectors.
Line conditioners keep a system’s AC power source voltage at a fairly constant
level and, therefore, can handle brownouts. Because of this added protection,
line conditioners cost more than surge protectors. However, line conditioners
cannot protect against a complete loss of power.
„
Uninterruptible Power Supply
KEMX-2030 User’s Manual
14
Preface
Uninterruptible power supply (UPS) systems offer the most complete protection
against variations on power because they use battery power to keep the server
running when AC power is lost. The battery is charged by the AC power while it
is available, so when AC power is lost, the battery can provide power to the
system for a limited amount of time, depending on the UPS system.
UPS systems range in price from a few hundred dollars to several thousand
dollars, with the more expensive unit s allowing you to run larger systems for a
longer period of time when AC power is lost. UPS systems that provide only 5
minutes of battery power let you conduct an orderly shutdown of the system,
but are not intended to provide continued operation. Surge protectors should be
used with all UPS systems, and the UPS system should be Underwriters
Laboratories (UL) safety approved.
KEMX-2030 User’s Manual
15
Chapter 1
Chapter 1
Introduction
„ Overview
The KEMX-2030 is a Mini-ITX form factor industrial motherboard combining the latest
Intel 45nm Intel® Atom™ processor with the high integration of the Intel® 945GSE/
ICH7-M chipset. The new architecture of Atom™ N270 enable the lowest power
consumption and smallest form factor for thin client and fundamental use. Featured
are DDR2-400/533 SODIMM up to 2GB, 18/ 24-bit LVDS, Fast Ethernet, SATA 3 Gb/s,
PCIe riser for 3x PCIe x1/ PCI/ mini PCI Expansion slot, 8x USB 2.0, 4 COM ports
with Power Selection, HD audio, and keyboard/mouse. The KEMX-2030 is a compact,
high performance industrial motherboard that is ideal for multimedia, gaming, mobile
PC, and thin client applications.
Checklist
„
„
„
Driver/ Manual CD
Quick Installation Guide
I/O Shield
„
„
KEMX-2030 Mini-ITX Embedded Board
SATA cable (7-pin connector with lock, L=46cm)
Features
„
„
„
„
„
„
„
„
Intel® Atom™ Processor N270
Intel® 945GSE / ICH7-M
Supports Dual Display, VGA,18/24-bit LVDS
DDR2 SO-DIMM Socket, total up to 2 GB
Mini PCI Socket, PCI slot, PCIe riser for 3x PCIe x1
2x SATA 3 Gb/s, 8x USB 2.0, 1x Fast Ethernet (Optional GbE)
4x COM ports, 4x DI/DO
Watchdog Timer, Hardware Monitor, TPM 1.2
KEMX-2030 User’s Manual
16
Chapter 1
„ Product Specifications
KEMX-2030`
CPU Support
Chipset
Intel® Atom™ N270
Intel® 945GSE + ICH7-M
Memory
BIOS
1x DDR2 400/533 SO-DIMM Socket, up to 2GB
AMI PnP 8Mb SPI ROM
Integrated on Intel® 945GSE Chipset
18/24-bit dual-channel LVDS from Chrontel CH7308
18-bit Dual channel LVDS from 945GSE optional
1x VGA
Display
1x RJ-45, Fast Ethernet (Realtek RTL8102E) or
1x RJ-45, Gigabit Ethernet (Realtek RTL8111C optional)
LAN
HD Audio Codec, supports Line-in, Line-out & Microphone (Realtek
ALC883)
Audio
Speak-out with AMP. 2x 2W
1x IDE (UltraDMA 100 / 66 / 33)
2x SATA 3Gb/s
4x COMs with Power Selection
8x USB 2.0
1x PS/2 Keyboard connector
1x PS/2 Mouse connector
1x Parallel port (Box Header)
4x DI/DO
Peripheral Support
TPM
TPM 1.2
Power Connector
ATX-4P or DC Jack for 12V Power Input only
1x PCI slot,
1x Mini PCI
Expansion
1x PCIe riser for 3x PCIe x1
Watchdog Timer
1-255 step, can be set with software on Super I/O
Hardware Monitor
Dimensions
Operating voltage, CPU temperature and fan speed
Mini-ITX (170 x 170 mm)
Operation Temp: 0ºC - 60ºC
Storage Temp.: -10ºC - 85ºC
Humidity: 0% - 90%
Environmental
Factors
Certifications
CE, FCC Class A
Table 1 KEMX-2030 Specification
KEMX-2030 User’s Manual
17
Chapter 2
Chapter 2
Hardware Settings
„ Overview
This chapter provides the definitions and locations of jumpers, headers, and
connectors.
Jumpers
The product has several jumpers which must be properly configured to ensure
correct operation.
Figure 3 Jumper Connector
For a three-pin jumper (see Figure 3), the jumper setting is designated “1-2” when
the jumper connects pins 1 and 2. The jumper setting is designated “2-3” when pins
2 and 3 are connected and so on. You will see that one of the lines surrounding a
jumper pin is thick, which indicates pin No.1.
To move a jumper from one position to another, use needle-nose pliers or tweezers
to pull the pin cap off the pins and move it to the desired position.
KEMX-2030 User’s Manual
20
Chapter 2
„ Jumper Settings and Pin Definitions
For jumper and connector locations, please refer to the diagrams below.
FP1
SATA1
JP1 JP2
CN2 JP3
LVDS1
IDE1
FP2
SATA2
LPT1
PCIE 1
CN11
CN3
DIMM1
MPCI 1
PCI 1
COM2 COM3 COM4
JP4
JP5
JP6
JP7
USB4 USB3 CN4
CN5
CN6
CN7
ATX1
JP9
JP8
CN8
J1
CN10
CN1
CN9
USB2 AUDIO1
Figure 4 Jumper and Connector Locations
KEMX-2030 User’s Manual
21
Chapter 2
Jumper Settings
To ensure correct system configuration, the following section describes how to set
the jumpers to enable/disable or change functions. For jumper descriptions, please
refer to the table below.
Table 2 Jumper List
Label
JP1
JP2
JP3
JP4
JP5
JP6
JP7
JP8
JP9
Function
Backlight Enable Selection
Backlight & Panel Power Selection
Clear CMOS Selection
COM1 Signal / Power Selection
COM2 Signal / Power Selection
COM3 Signal / Power Selection
COM4 Signal / Power Selection
For Quanmax internal test only
Power Mode Selection
Table 3 JP1 Backlight Enable Selection
Jumper
1-2
2-3
Status
Active High (Default)
Active Low
Pitch:2.0mm [YIMTEX 3291*03SAGR(6T)]
Table 4 JP2 Backlight & Panel Power Selection
Jumper
Setting
1-3
Status
Backlight Power = +12V (Default)
Backlight Power = +5V
1
3-5
2-4
Panel Power = +3.3V (Default)
Panel Power = +5V
2
4-6
Pitch 2.54mm [YIMTEX 3362*03SAGR]
Table 5 JP3 Clear CMOS Selection
Jumper
Open
Short
Status
Normal Operation (Default)
Clear CMOS
Pitch:2.54mm [YIMTEX 3321*02SAGR(6T)]
KEMX-2030 User’s Manual
22
Chapter 2
Table 6 JP4 COM1 Signal / Power Selection
Jumper
Setting
Function
1-3 Short Pin 1 of COM1 = +12V
3-5 Short Pin 1 of COM1 = +5V
5-7 Short Pin 1 of COM1 = +5V
1
Pin 1 of COM1 = DCD@RS232,
TX-@RS422, DATA-@RS485 (Default)
7-9 Short
2-4 Short Pin 9 of COM1 = +12V
4-6 Short Pin 9 of COM1 = +5V
6-8 Short Pin 9 of COM1 = +5V
8-10 Short Pin 9 of COM1 = RI (Default)
2
Pitch:2.54mm [YIMTEX 3322*05SAGR(6T]
Table 7 JP5/ 6/ 7 COM2/ 3/ 4 Signal / Power Selection
Jumper
Setting
Function
1-3 Short Pin 1 of COM2/ 3/ 4 = +12V
3-5 Short Pin 1 of COM2/ 3/ 4 = +5V
5-7 Short Pin 1 of COM2/ 3/ 4 = +5V
1
7-9 Short Pin 1 of COM2/ 3/ 4 = DCD (Default)
2-4 Short Pin 9 of COM2/ 3/ 4 = +12V
4-6 Short Pin 9 of COM2/ 3/ 4 = +5V
2
6-8 Short Pin 9 of COM2/ 3/ 4 = +5V
8-10 Short Pin 9 of COM2/ 3/ 4 = RI (Default)
Pitch:2.54mm [YIMTEX 3322*05SAGR(6T]
Table 8 JP8 For Quanmax internal test only, do not change default setting
Jumper
1-2
Status
Normal (Default)
Debug Mode
2-3
Pitch:2.0mm [YIMTEX 3291*03SAGR(6T)]
Table 9 JP9 Power Mode Selection
Jumper
Open
Status
AT Mode
ATX Mode (Default)
Short
Pitch:2.54mm [YIMTEX 3321*02SAGR(6T)]
KEMX-2030 User’s Manual
23
Chapter 2
Rear Panel Pin Assignments
Figure 5 Rear Panel IO
Table 10 Rear Panel Connector List
Label
Function
AUDIO1 3-Port Audio phone jack
USB2
CN9
CN1
CN10
J1
USB2.0 Port 2 , 3 Type A Connector
USB2.0 Port 0, 1 Type A Connector & 10/100 Ethernet RJ-45 Connector
VGA Connector & RS-232(422/485) Port A DB-9 Connector
PS/2 KB/MS Connector
+12V Power Input Connector
Table 11 AUDIO1, 3-Port Audio phone jack
Signal Name
BLUE
GREEN
PINK
LINE IN
LINE OUT
MIC IN
AUDIO JACK*3 DIP Vertical [Foxconn JA33331-H11P-4F]
Table 12 USB2, USB2.0 Port 2, 3 Type A Connector
Pin
1
Signal Name
+5V
Pin
5
Signal Name
+5V
2
USB1-
USB1+
GND
6
USB0-
USB0+
GND
3
7
4
8
USB DIP 4*2P 90D [KUON YI KS-002-ANB-L]
KEMX-2030 User’s Manual
24
Chapter 2
Table 13 CN9, USB2.0 Port 0, 1 Connector & Ethernet RJ-45 Connector
Pin
1
Signal
Pin
U1
U2
U3
U4
U5
U6
U7
U8
Signal
+5V
MDI[0]+
MDI[0]-
MDI[1]+
MDI[1]-
MDI[2]+
MDI[2]-
MDI[3]+
MDI[3]-
2
USB0-
USB0+
GND
3
4
5
+5V
6
USB1-
USB1+
GND
7
8
USB*2/RJ45*1+TFM+LED(10/100)22P DIP 90° [UDE RU1-161A1Z1F(XB)]
Table 14 CN1, VGA Connector & RS-232(422/485) Port A DB-9 Connector
RS485
RS422
(COM1*)
Pin
RS232
Half Duplex
(COM1*)
DATA-
N/A
1
2
3
4
5
6
7
8
9
DCD, Data carrier detect
RXD, Receive data
TXD, Transmit data
DTR, Data terminal ready
TX-
RX+
TX+
RX-
DATA+
N/A
GND, ground
DSR, Data set ready
RTS, Request to send
CTS, Clear to send
RI, Ring indicator
Signal Name
Red
Pin
1
Pin
2
Signal Name
Green
NC
Blue
3
4
GND
5
6
GND
GND
GND
GND
7
8
VCC
9
10
12
14
NC
11
13
15
DDC2B data
VSYNC
HSYNC
DDC2B clock
D-SUB 9P(M)&15S(19.05mm(F) FOR PC99 FOLLOW PANTONE
COLOR[ D201B1N01002N]
KEMX-2030 User’s Manual
25
Chapter 2
Table 15 CN 10, PS/2 KB/MS Connector
Pin
1
Signal
KBDAT
NC
Function
Keyboard Data
No Connect
2
3
GND
Ground
4
KB5V
KBCLK
NC
+5VSB Power Source
Keyboard Clock
No Connect
5
6
7
MSDAT
NC
Mouse Data
8
No Connect
9
GND
Ground
10
11
12
KB5V
MSCLK
NC
+5VSB Power Source
Mouse Clock
No Connect
MINI DIN DIP 6/6P MH11061-P36-4F 90D(F) Kb/Ms for PC99 CONNECTOR
[FOXCONN]
Table 16 J1, +12V Power Input Connector
Pin
1
Signal
NC
2
+12V
GND
3
DC POWER DIP 3PIN φ 2.5mm 90° [KUON YI KD-014SA-L]
NOTE
Do not use J1 & ATX1 connectors at the same time.
KEMX-2030 User’s Manual
26
Chapter 2
Main Board Pin Assignments
Table 17 Internal Connector List
Function
Panel Backlight Wafer
Label
CN2
CN3
CN4
CN5
CN6
Digital Input / Output Pin Header
Front Panel Audio Pin Header
CD-In Connector Pin Header
SPDIF Pin Header
CN7
CN8
CN11
DIMM1
FP1
FP2
LVDS1
IDE1
SATA1
SATA2
USB3
USB4
COM2
COM3
COM4
PCIE1
MPCI1
PCI1
Audio AMP Right Output Wafer
Audio AMP Left Output Wafer
AT Power Wafer
DDR2 Memory SO-DIMM Socket
Front Panel 1 Pin Header
Front Panel 2 Pin Header
LVDS Panel Pin Header
44PIN 2.0mm Pin Header
Serial ATA Connector
Serial ATA Connector
USB2.0 Port 4, 5 Pin Header
USB2.0 Port 6, 7 Pin Header
RS-232 Port 2 With Power Wafer
RS-232 Port 3 With Power Wafer
RS-232 Port 4 With Power Wafer
PCIE slots
Mini PCI slots
PCI slots
ATX1
LPT1
+12V Power Input Connector
Parallel Port Wafer
Table 18 CN2, Panel Backlight Wafer
Pin
7
Signal Name
NC
BL_ADJ
6
5
GND
4
+5V / +12V *
+5V / +12V *
GND
3
2
1
BL_EN / BL_EN# *
*：Selected by JP2
**：Selected by JP1
Pitch:1.25mm WAFER [YIMTEX 501MW1*7STR]
KEMX-2030 User’s Manual
27
Chapter 2
Table 19 CN3, Digital Input / Output Pin Header
Pin
1
Signal
Pin
2
Signal
Digital Output 0
Digital Output 1
Digital Output 2
Digital Output 3
+5V
Digital Input 0
Digital Input 1
Digital Input 2
Digital Input 3
GND
3
4
5
6
7
8
9
10
Pitch:2.54mm [YIMTEX 3322*05SAGR(6T]
Table 20 CN4, Front Panel Audio Pin Header
Pin
1
Signal
MIC2-L
Pin
2
Signal
Audio GND
ACZ_DET#
MIC2_JD
Key
3
MIC2-R
Line2-R
FIO_Sense
Line2-L
4
5
6
7
8
9
10
Line2_JD
Pitch:2.54mm w/o Pin 8 [YIMTEX 3322*05SAGR(6T)-08]
Table 21 CN5, CD-In Connector
Pin
1
Signal Name
CD-IN-R
GND
2
3
GND
4
CD-IN-L
Pitch:2.54mm WAFER [YIMTEX 522CW4SGR]
Table 22 CN6, S/PDIF Pin Header
Pin
1
Signal Name
S/PDIF In
GND
2
3
S/PDIF Out
GND
4
Pitch:2.54mm [YIMTEX 3321*04SAGR(6T)]
KEMX-2030 User’s Manual
28
Chapter 2
Table 23 CN7, Audio AMP Right Output Wafer
Pin
1
Signal Name
Speaker+
2
Speaker-
Pitch=2.0mm WAFER [YIMTEX 503PW1*02STR]
Table 24 CN8, Audio AMP Left Output Wafer
Pin
1
Signal Name
Speaker+
2
Speaker-
Pitch=2.0mm WAFER [YIMTEX 503PW1*02STR]
Table 25 CN11, AT Power Output Wafer
Pin
1
Signal Name
+12V
2
GND
3
GND
4
+5V
Pitch: 5.08mm W/O LOCK [VENSIK 2470-F-04PST-PB]
Table 26 FP1, Front Panel 1 Pin Header
Pin
1
Signal
Pin
2
Signal
Reset Button +
Reset Button -
HDD LED +
HDD LED -
Speaker +
NC
3
4
5
6
NC
7
8
Speaker -
Pins 2, 8: External Speaker wire
Pins 6-8 shorted: Internal Speaker Enable (default)
Pitch:2.54mm [YIMTEX 3322*04SAGR(6T)]
KEMX-2030 User’s Manual
29
Chapter 2
Table 27 FP2, Front Panel 2 Pin Header
Pin
1
Signal
Power LED +
NC
Pin
2
Signal
Power Button +
Power Button -
NC
3
4
5
Power LED -
Keyboard
Lock
6
7
8
SMBus Data
9
GND
10
SMBus Clock
Pitch:2.54mm [YIMTEX 3322*05SAGR(6T]
Table 28 LVDS1, LVDS Panel Connector
Pin Signal Name Pin Signal Name
1
NC
2
NC
3
LVDS_A0-
LVDS_A1-
LVDS_A2-
LVDS_ACK-
LVDS_A3-
GND
4
LVDS_A0+
LVDS_A1+
LVDS_A2+
LVDS_ACK+
LVDS_A3+
GND
5
6
7
8
9
10
12
14
16
18
20
22
24
26
11
13
15
17
19
21
23
25
27
LVDS_B0-
LVDS_B1-
LVDS_B2-
LVDS_BCK-
LVDS_B3-
NC
LVDS_B0+
LVDS_B1+
LVDS_B2+
LVDS_BCK+
LVDS_B3+
GND
NC
28 +3.3V / +5V *
29 +3.3V / +5V * 30 +3.3V / +5V *
*：Selected by JP2
Pitch:2.0mm CUT27 [YIMTEX 3292*15SAGR(6T)-27]
KEMX-2030 User’s Manual
30
Chapter 2
Table 29 IDE1, Primary 44-pin IDE Box Header
Signal Name
Reset IDE
IDE Data 7
IDE Data 6
IDE Data 5
IDE Data 4
IDE Data 3
IDE Data 2
IDE Data 1
IDE Data 0
Ground
Pin
1
Pin
2
Signal Name
GND
3
4
IDE Data 8
IDE Data 9
IDE Data 10
IDE Data 11
IDE Data 12
IDE Data 13
IDE Data 14
IDE Data 15
NC
5
6
7
8
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
DREQ0
GND
IDEIOW#
GND
IDEIOR#
GND
IDEIORDY
DACK0#
CBSEL
GND
IDEIRQ14
IDE Address 1
IDE Address 0
IDE Chip select 1#
IDE activity
+5V
NC
PDIAG#
IDE Address 2
IDE Chip select 3#
GND
+5V
NC
GND
Pitch:2.0mm [YIMTEX 32644SAGR(6T)]
Table 30 SATA1,2, SATA Connector
Pin
1
Signal Name
GND
2
TX+
3
TX-
4
GND
5
RX-
6
RX+
7
GND
SATA WATM-07ABN4B2B8UW4 [WIN WIN]
KEMX-2030 User’s Manual
31
Chapter 2
Table 31 USB3, USB2.0 Port 4, 5 Pin Header
Pin
1
Signal Name
+5V
Pin Signal Name
2
4
+5V
USB5-
USB5+
GND
3
USB4-
USB4+
GND
5
6
7
8
9
KEY
10
GND
Pitch:2.54mm [YIMTEX 3322*05SAGR(6T) -09]
Table 32 USB4, USB2.0 Port 6, 7 Pin Header
Pin Signal Name Pin Signal Name
1
3
5
7
9
+5V
USB6-
USB6+
GND
2
4
+5V
USB7-
USB7+
GND
6
8
KEY
10
GND
Pitch:2.54mm [YIMTEX 3322*05SAGR(6T) -09]
Table 33 COMx RS-232 Port-x Box Header（x = 2, 3, 4）
Pin
Signal
1
+5V / +12V / DCD, Data carrier detect
Note：Selected by JPx
2
4
5
3
6
7
8
9
RXD, Receive data
DTR, Data terminal ready
GND, ground
TXD, Transmit data
DSR, Data set ready
RTS, Request to send
CTS, Clear to send
+5V / +12V / RI, Ring indicator
Note：Selected by JPx
10
NC
Pitch:2.54mm [YIMTEX 32510SAG1R(6T)]
KEMX-2030 User’s Manual
32
Chapter 2
Table 34 PCIE1 PCIE slots
PCIE slots
Side B
Pin
1
Side A
3.3V
12V
12V
2
3.3V
3
3.3VSB
PCIE_WAKE#
PCI_RST#
Ground
PCIE_TXP2
PCIE_TXN2
Ground
PCIE_TXP3
PCIE_TXN3
Ground
Ground
NC
Ground
4
CLK100_PCIE+
CLK100_PCIE-
Ground
5
6
7
PCIE_RXP2
PCIE_RXN2
Ground
8
9
10
11
12
13
14
15
16
17
18
PCIE_RXP3
PCIE_RXN3
Ground
Ground
NC
NC
NC
Ground
NC
Ground
NC
NC
NC
PCI 18*2P EXPRESS 180D(F) Black [ Win Win WPES--036AN41B22UWS]
Table 35 MPCI1, Mini-PCI Socket
Pin
1
Signal
NC
Pin
2
Signal
NC
3
NC
4
NC
5
NC
6
NC
7
NC
8
NC
9
NC
NC
NC
10
12
14
16
18
20
22
24
26
28
30
32
NC
NC
NC
NC
11
13
15
17
19
21
23
25
27
29
31
GND
INTA#
+3.3V
NC
GND
PCICLK
GND
REQ#
+3.3V
+5V
INTD#
NC
+3.3V_SB
RST#
+3.3V
GNT#
GND
KEMX-2030 User’s Manual
33
Chapter 2
PME#
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
71
73
75
77
79
81
83
85
87
89
AD31
AD29
GND
AD27
AD25
NC
CBE3#
AD23
GND
AD21
AD19
GND
AD17
CBE2#
IRDY#
+3.3V
NC
SERR#
GND
PERR#
CBE1#
AD14
GND
AD12
AD10
GND
AD8
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
74
76
78
80
82
84
86
88
90
NC
AD30
+3.3V
AD28
AD26
AD24
IDSEL
GND
AD22
AD20
PAR
AD18
AD16
GND
FRAME#
TRDY#
STOP#
+3.3V
DEVSEL#
GND
AD15
AD13
AD11
GND
AD9
CBE0#
+3.3V
AD6
AD7
+3.3V
AD5
91
92
AD4
93
NC
94
AD2
95
AD3
96
AD0
97
+5V
98
NC
99
AD1
GND
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
+5V
100
102
104
106
108
110
112
114
116
118
120
122
124
NC
101
103
105
107
109
111
113
115
117
119
121
123
GND
GND
NC
NC
NC
NC
GND
NC
NC
NC
NC
+3.3V
MINIPCI [FOXCONN AS0B126-S99N-4F]
KEMX-2030 User’s Manual
34
Chapter 2
Table 36 PCI1, PCI slots
5V Board PCI Revision 2.1
Pin
1
2
Side B
-12V
TCK
Side A
TRST_L
+12V
Comments
32-bit start
3
4
Ground
TDO
TMS
TDI
5
+5V
+5V
6
7
8
9
+5V
INTA_L
INTC_L
+5V
Reserved
+5V
Reserved
Ground
Ground
Reserved
RST_L
+5V
GNT_L
Ground
Reserved
AD[30]
+3.3V
AD[28]
AD[26]
Ground
AD[24] +3.3V
IDSEL
+3.3V
AD[22]
AD[20]
Ground
AD[18]
AD[16]
+3.3V
FRAME_L
Ground
TRDY_L
Ground
STOP_L
+3.3V
Reserved
Reserved
Ground
PAR
INTB_L
INTD_L
PRSNT1_L
Reserved
PRSNT2_L
Ground
Ground
Reserved
Ground
CLK
Ground
REQ_L
+5V
AD[31]
AD[29]
Ground
AD[27]
AD[25]
+3.3V
C/BE[3]_L
AD[23]
Ground
AD[21]
AD[19]
+3.3V
AD[17]
C/BE[2]_L
Ground
IRDY_L
+3.3V
DEVSEL_L
Ground
LOCK_L
PERR_L
+3.3V
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
3.3V key
3.3V key
SERR_L
+3.3V
C/BE[1]_L
AD[14]
Ground
AD[12]
AD[10]
Ground
AD[15]
+3.3V
AD[13]
AD[11]
Ground
AD[09]
KEMX-2030 User’s Manual
35
Chapter 2
5V Board PCI Revision 2.1
Pin
50
51
52
53
54
55
56
57
58
59
60
61
62
Side B
KEYWAY
KEYWAY
AD[08]
AD[07]
+3.3V
AD[05]
AD[03]
Ground
AD[01]
+5V
Side A
KEYWAY
KEYWAY
C/BE[0]_L
+3.3V
AD[06]
AD[04]
Ground
AD[02]
AD[00]
+5V
Comments
5V key
5V key
ACK64_L
+5V
+5V
REQ64_L
+5V
+5V
32-bit end
PCI 60*2P 180D (F) [FOXCONN EH06001-DAW-DF]
Table 37 ATX1, +12V Power Input Connector
Pin
1
Signal Name
GND
2
GND
3
+12V
4
+12V
Pitch:4.2mm [YIMTEX 576MWA2*02STR]
NOTE
Do not use J1 & ATX1 connectors at the same time.
Table 38 Parallel Port Wafer
Pin
1
3
5
7
Signal Name
STB
Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
Signal Name
#AFD
#ERR
#INIT
#SLIN
GND
PD0
PD1
PD2
PD3
PD4
PD5
PD6
PD7
9
11
13
15
17
19
21
23
25
GND
GND
GND
GND
GND
GND
GND
GND
#ACK
BUSY
PE
SLCT
Pitch:2.54mm [YIMTEX 32526SAG1R(6T)]
KEMX-2030 User’s Manual
36
Chapter 3
Chapter 3
System Installation
„ Expansive Interfaces
The board comes with one PCIex1 slot , one PCI slot and one Mini-PCI interface.
1x PCIe riser for 3x PCIe x1
32-bit, 33MHz PCI slot
32-bit, 33MHz Mini-PCI socket
Figure 6 Expansive Interfaces
NOTE
When adding or removing expansion cards, make sure that you unplug the
power supply first. Meanwhile, read the documentation for the expansion card
to configure any necessary hardware or software settings for the expansion
card, such as jumpers, switches or BIOS configuration.
„ Memory Module Installation
Carefully follow the steps below in order to install the DIMMs:
1. To avoid generating static electricity and damaging the SO-DIMM, ground
yourself by touching a grounded metal surface or use a ground strap before you
touch the SO-DIMM.
2. Do not touch the connectors of the SO-DIMM. Dirt or other residue may cause a
malfunction.
KEMX-2030 User’s Manual
37
Chapter 3
3. To make sure the correct DDR2 SO-DIMM notches should match with the
DDR2 SO-DIMM.
4. Hold the SO-DIMM with its notch aligned with the memory socket of the board
and insert it at a 30-degree angle into the socket.
Figure 7 Align the SO-DIMM Memory Module with the onboard socket
5. Fully insert the module into the socket until a “click” is heard.
6. Press down on the SO-DIMM so that the tabs of the socket lock on both sides
of the module
Figure 8 Press down on the SO-DIMM Memory Module to lock it in place
Removing a DIMM:
To remove the SO-DIMM, use your fingers or a small screwdriver to carefully push
away the tabs that secure either side of the SO-DIMM. Lift it out of the socket.
Make sure you store the SO-DIMM in an anti-static bag. The socket must be
populated with memory modules of the same size and manufacturer.
KEMX-2030 User’s Manual
38
Chapter 4
Chapter 4
AMI BIOS Setup
„ Overview
This chapter provides a description of the AMI BIOS. The BIOS setup menus and
available selections may vary from those of your product. For specific information on
the BIOS for your product, please contact Quanmax.
NOTE: The BIOS menus and selections for your product may vary from
those in this chapter. For the BIOS manual specific to your product, please
contact Quanmax
AMI's ROM BIOS provides a built-in Setup program, which allows the user to modify
the basic system configuration and hardware parameters. The modified data will be
stored in a battery-backed CMOS, so that data will be retained even when the power
is turned off. In general, the information saved in the CMOS RAM will not need to be
changed unless there is a configuration change in the system, such as a hard drive
replacement or when a device is added.
It is possible for the CMOS battery to fail, which will cause data loss in the CMOS
only. If this happens you will need to reconfigure your BIOS settings.
KEMX-2030 User’s Manual
39
Chapter 4
„ Main Menu
The BIOS Setup is accessed by pressing the DEL key after the Power-On Self-Test
(POST) memory test begins and before the operating system boot begins. Once you
enter the BIOS Setup Utility, the Main Menu will appear on the screen. The Main
Menu provides System Overview information and allows you to set the System Time
and Date. Use the “<” and “>” cursor keys to navigate between menu screens.
Table 39 BIOS Main Menu
BIOS SETUP UTILITY
M a i n
A d v a n c e d
B o o t
C h i p s e t
P o w e r
S e c u r i t y
E x i t
System Date
System Time
[Wed 11/05/2008]
[10:18:15]
Use [ENTER], [TAB]
or [SHIFT-TAB] to
select a field.
> Primary IDE Master
> Primary IDE Slave
> Secondary IDE Master
> Secondary IDE Slave
:[Not Detected]
:[Not Detected]
:[Not Detected]
:[Not Detected]
Use [+] or [-] to
configure system Time.
> System Information
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Below table is described for Primary IDE Master, Primary IDE Slave, Secondary IDE
Master, and Secondary IDE Slave setting.
Table 40 IDE Device Setting Menu
BIOS SETUP UTILITY
M a i n
A d v a n c e d
B o o t
C h i p s e t
P o w e r
S e c u r i t y
E x i t
Primary Master
Device
Disable: Disables LBA Mode.
Auto: Enables LBA Mode if the
device supports it and the
device is not already formatted
with LBA Mode disabled.
:Not Detected
LBA/ Large Mode
DMA Mode
S.M.A.R.T
[Auto]
[Auto]
[Auto]
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
KEMX-2030 User’s Manual
40
Chapter 4
LBA/ Large Mode
Enables or disables the LBA (Logical Block Addressing)/ Large mode. Setting to
Auto enables the LBA mode if the device supports this mode, and if the device was
not previously formatted with LBA mode disabled. Options: Disabled, Auto
DMA Mode
Options: Auto
S.M.A.R.T
SMART stands for Smart Monitoring, Analysis, and Reporting Technology. It allows
AMIBIOS to use the SMART protocol to report server system information over a
network. Options: Auto, Disabled, Enabled
Table 41 System Information
BIOS SETUP UTILITY
M a i n
A d v a n c e d
: 1.3
B o o t
C h i p s e t
P o w e r
S e c u r i t y
E x i t
AMIBIOS
Version
Build Date:
:12/26/08
Processor
Intel® Atom™ CPU N270
Speed
Count
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
@ 1.60GHz
:1600MHz
:1
System Memory
Size
:1016MB
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
„ Advanced Menu
Table 42 Advanced Menu
BIOS SETUP UTILITY
M a i n
Ad va n c e d
B o o t
C h i p s e t
P o w e r
S e c u r i t y
E x i t
Advanced Settings
Warning: Setting wrong values in below sections
may cause system to malfunction.
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
> I/O Configuration
> OnBoard Peripherals Configuration
> Trusted Computing
> Hardware Health Configuration
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Press <Enter> to select a sub-menu for detailed options.
KEMX-2030 User’s Manual
41
Chapter 4
Table 43 Onboard I/O Configuration
BIOS SETUP UTILITY
M a i n
Ad va n c e d
B o o t
C h i p s e t
P o w e r
S e c u r i t y
E x i t
Allow BIOS to Select Serial
Port1 Base Address.
Onboard I/O Configuration
COM1 Address
COM1 IRQ
[3F8]
[4]
COM1 Function Type
COM2 Address
COM2 IRQ
COM3 Address
COM3 IRQ
COM3 Mode
COM4 Address
COM4 IRQ
[RS232]
[2F8]
[4]
[3E8]
[10]
[Normal]
[2E8]
[11]
[Normal]
[378]
[Normal]
[IRQ7]
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
COM4 Mode
Parallel Port Address
Parallel Port Mode
Parallel Port IRQ
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
COM1 Address
Options: Disabled, 3F8, 3E8, 2E8
COM1 IRQ
Options: 3, 4, 10, 11
COM1 Function Type
Options: RS232, RS422, RS485
COM2 Address
Options: Disabled, 2F8, 3E8, 2E8
COM2 IRQ
Options: 3, 4, 10, 11
COM3 Address
Options: Disabled, 3F8, 2F8, 3E8, 2E8, 2F0, 2E0
COM3 IRQ
Options: 3, 4, 10, 11
COM3 Mode
Options: Normal, IrDA, ASK IR, Smart Card Reader
COM4 Address
Options: Disabled, 3F8, 2F8, 3E8, 2E8, 2F0, 2E0
COM4 IRQ
Options: 3, 4, 10, 11
COM4 Mode
Options: Normal, IrDA, ASK IR, Smart Card Reader
Parallel Port Address
Options: 378, 278, 3BC
Parallel Port Mode
KEMX-2030 User’s Manual
42
Chapter 4
Options: Normal, EPP, ECP, EPP+ECP
Parallel Port IRQ
Options: IRQ5, IRQ7
Table 44 OnBoard Peripherals Configuration Settings
BIOS SETUP UTILITY
M a i n
Ad va n c e d
B o o t
C h i p s e t
P o w e r
S e c u r i t y
Options
E x i t
OnBoard Peripherals Configuration Settings
USB Controller
USB Device Legacy Support
Audio Controller
Onboard LAN Controller
Onboard LAN OPTROM
[Enable]
[Enable]
[Enable]
[Enable]
[Disabled]
Disabled
Enabled
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
USB Controller
Options: Enabled, Disabled
USB Device Legacy Support
Options: Enabled, Disabled, Auto
Audio Controller
Options: Enabled, Disabled
Onboard LAN Controller
Options: Enabled, Disabled
Onboard LAN OPTROM
Options: Enabled, Disabled
KEMX-2030 User’s Manual
43
Chapter 4
Table 45 Trusted Computing
BIOS SETUP UTILITY
M a i n
Ad va n c e d
B o o t
C h i p s e t
P o w e r
S e c u r i t y
E x i t
Trusted Computing
Enable/ Disable TPM
TCG (TPM 1.1/1.2) supp
in BIOS
TCG/TPM SUPPORT
[NO]
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
TCG/TPM SUPPORT
Options: No, Yes
Table 46 Hardware Health Configuration
BIOS SETUP UTILITY
M a i n
Ad va n c e d
B o o t
C h i p s e t
P o w e r
S e c u r i t y
E x i t
Hardware Health Configuration
CPU Warning Temperature
CPU Shutdown Temperature
[Disabled]
[Disabled]
Temperature Sensor #1
Temperature Sensor #1
:57°C/ 134°F
:43°C/ 109°F
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
+VCORE
+1.05V
+3.3V
+5V
+12V
:1.136 V
:1.040 V
:3.166 V
:4.958 V
:11.182 V
:1.758 V
:3.365 V
+1.8v
+VCC RTC
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
CPU Warning Temperature
Options: Disabled, 80°C/176°F, 85°C/185°F, 90°C/194°F, 95°C/203°F
CPU Shutdown Temperature
Options: Disabled, 80°C/176°F, 85°C/185°F, 90°C/194°F, 95°C/203°F
KEMX-2030 User’s Manual
44
Chapter 4
„ Boot Menu
Table 47 Boot Menu
BIOS SETUP UTILITY
M a i n
A d v a n c e d
B o o t
C h i p s e t
P o w e r
S e c u r i t y
E x i t
Boot Settings
Allow BIOS to Skip certain
tests while booting. This
will decrease the time
needed to boot the
system.
Quick Boot
[Enabled]
[ON]
[Enabled]
[Enabled]
Bootup Num-Lock
Wait For ’F1’ If Error
Hit ’DEL’Message Display
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Quick Boot
Enabling this item allows BIOS to skip some Power On Self Tests (POST) while
booting to decrease the time needed to boot the system. When set to [Disabled],
BIOS performs all the POST items.
Options: Disabled, Enabled
Bootup Num-Lock [On]
Allow you to select the power-on state for the NumLock.
Options: Off, On
Wait for ‘F1’ If Error [Enabled]
When set to Enabled, the system waits for F1 key to be pressed when error occurs.
Options: Disabled, Enabled
Hit ‘DEL’ Message Display [Enabled]
When set to Enabled, the system displays the message ‘Press DEL to run Setup’
during POST.
Options: Disabled, Enabled
KEMX-2030 User’s Manual
45
Chapter 4
„ Chipset Menu
Table 48 Chipset Menu
BIOS SETUP UTILITY
M a i n
A d v a n c e d
B o o t
C h i p s e t
P o w e r
S e c u r i t y
Options
E x i t
Chipset Settings
DRAM Frequency
[Auto]
Auto
400 MHz
533 MHz
Boots Graphic Adapter Priority
Internal Graphics Mode Select
Hyper Threading Technology
[PEG/PCI]
[Enabled, 8MB]
[Enabled]
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
> Video Function Configuration
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
DRAM Frequency
Options: Auto, 400 MHz, 533MHz
Boots Graphic Adapter Priority
Select which graphics controller to use as the primary boot device.
Options: IGD, PCI/IGD, PCI/PEG, PEG/IGD, PEG/PCI
Internal Graphics Mode Select
Select the amount of system memory used by the Internal graphics device.
Options: Disabled, Enabled 1MB, Enabled 8M
Hyper Threading Technology
Options: Disabled, Enabled
KEMX-2030 User’s Manual
46
Chapter 4
„
Video Function Configuration
Table 49 Video Function Configuration
BIOS SETUP UTILITY
C h i p s e t
M a i n
A d v a n c e d
B o o t
P o w e r
S e c u r i t y
Options
E x i t
Video Function Configuration
DVMT Mode Select
[DVMT Mode]
[128M]
Fixed Mode
DVMT Mode
Combo Mode
DVMT/FIXED Memory
Boot Display Device
Flat Panel Type
[VGA]
[1024X768 24Bit 1C]
Local Flat Panel Scaling
Panel BackLight Voltage
[Auto]
[2.5]
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
DVMT Mode Select
Options: Fixed Mode, DVMT Mode, Combo Mode
DVMT/FIXED Memory
Options: 64MB, 128MB, Maximum DVMT
Boot Display Device
Options: VGA, LVDS, VGA+LVDS
Flat Panel Type
Options:
640x480
24Bit 1CH
24Bit 1CH
24Bit 2CH
24Bit 2CH
1024x768
1280x1024
1600x1200
Local Flat Panel Scaling
Options: Auto, Forced Scaling, Disabled
Panel BackLight Voltage
Options: Min 0.0V, Max: 5.0V
KEMX-2030 User’s Manual
47
Chapter 4
„ Power Menu
Table 50 Power Menu
BIOS SETUP UTILITY
M a i n
A d v a n c e d
B o o t
C h i p s e t
P o w e r
S e c u r i t y
E x i t
Power Management Setting
Select the ACPI state used for
System Suspend
ACPI Function
[Enabled]
Suspend mode
Repost Video on S3 Resume
Suspend Time Out
Restore on AC Power Loss
Resume By USB Device
Resume On PME#
Resume By PCI-E Device
Resume On RTC Alarm
[S3 (STR)]
[No]
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
[Disabled]
Power Off]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
ACPI Function
Enable/ Disable ACPI support for Operating System.
ENABLE: If OS supports ACPI, DISABLE: IF OS Does not support ACPI.
Suspend mode
Options: S1 (POS), S3 (STR)
Repost Video on S3 Resume
Options: No, Yes
Suspend Time Out
Options: Disabled, 1 Min, 2 Min, 4 Min, 8 Min, 10 Min, 20 Min, 30 Min, 40 Min, 50
Min, 60 Min
Restore on AC Power Loss
Options: Power OFF, Power ON, Last State
Resume By USB Device
Enable/ Disable USB Device Wakeup From S3/S4
Options: Disabled, Enabled
Resume On PME#
Options: Disabled, Enabled
Resume By PCI-E Device
Options: Disabled, Enabled
Resume On RTC Alarm
Options: Disabled, Enabled,
If the value is Enabled.
RTC Alarm Date (Days) [Every Day]
KeyIn “+”/”-“ to select
RTC Alarm Time
[00:00:00]
Use [ENTER], [TAB] or [SHIFT+TAB] to select a field
Use [+] or [-] to configure system time
KEMX-2030 User’s Manual
48
Chapter 4
Security Menu
Table 51 Security Menu
BIOS SETUP UTILITY
M a i n
A d v a n c e d
B o o t
C h i p s e t
P o w e r
S e c u r i t y
E x i t
Security Setting
Install or Change the password.
Supervisor Password :Not Installed
User Password :Not Installed
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
Change Supervisor Password
Change User Password
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Change Supervisor Password
Select this item to set or change the supervisor password. The Supervisor Password
item on top of the screen displays the default Not Installed. After you have set a
password, this item displays Installed.
Change User Password
Select this item to set or change the user password. The User Password item on top
of the screen displays the default Not Installed. After you have set a password, this
item displays Installed.
KEMX-2030 User’s Manual
49
Chapter 4
„ Exit Menu
Table 52 Exit Menu
BIOS SETUP UTILITY
M a i n
A d v a n c e d
B o o t
C h i p s e t
P o w e r
S e c u r i t y
E x i t
Exit Setting
Exit System Setup after saving
the changes.
Save Changes and Exit
Discard Changes and Exit
Discard Changes
F10 key can be used
for this operation.
Load Optimal Defaults
Load Failsafe Defaults
<> Select Screen
↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 (C)Copyright 1985-2006, American Megatrends, Inc.
Save Changes and Exit
Exit system setup after saving the changes. Once you are finished making your
selections, choose this option from the Exit menu to ensure the values you selected
are saved to the CMOS RAM. The CMOS RAM is sustained by an onboard backup
battery and stays on even when the PC is turned off. When you select this option, a
confirmation window appears. Select [Yes] to save changes and exit.
Discard Changes and Exit
Exit system setup without saving any changes. Select this option only if you do not
want to save the changes that you made to the Setup program. If you made changes
to fields other than system date, system time, and password, the BIOS asks for a
confirmation before exiting.
Discard Changes
Discards changes done so far to any of the setup values. This option allows you to
discard the selections you made and restore the previously saved values. After
selecting this option, a confirmation appears. Select [Yes] to discard any changes and
load the previously saved values.
Load Optimal Defaults
Load Optimal Default values for all the setup values. This option allows you to load
optimal default values for each of the parameters on the Setup menus, which will
provide the best performance settings for your system. The F9 key can be used for
this operation.
KEMX-2030 User’s Manual
50
Chapter 4
Load Failsafe Defaults
Load Optimal Default values for all the setup values. This option allows you to load
failsafe default values for each of the parameters on the Setup menus, which will
provide the most stable performance settings. The F8 key can be used for this
operation.
KEMX-2030 User’s Manual
51
Chapter 5
Chapter 5
Driver Installation
If your KEMX-2030 does not come with an operating system pre-installed, you will
need to install an operating system and the necessary drivers to operate it. After you
have finished assembling your system and connected the appropriate power source,
power it up using the power supply and install the desired operating system.
You can download the drivers for the KEMX-2030 from the Quanmax website
please contact Quanmax.
NOTE
When the system reboots without connecting the CRT, there might be no
image on screen when you insert the CRT/VGA cable. Please
pressing <Ctrl>+<Alt>+<F1> simultaneously to show the image on screen.
KEMX-2030 User’s Manual
52
Appendix A
Appendix A
System Resources
Interrupt Request (IRQ) Lines
IRQ # Used For
Timer0
Comment
0
1
2
keyboard controller
Cascade
3
4
COM2
COM1
Note (1)
Note (1)
5
Free
6
7
Floppy disk controller
Free
Note (1)
8
9
10
11
12
13
Real Time Clock
ACPI-Compliant System
Free
COM3&4
PS/2 Mouse
Floating point unit (FPU /
NPU / Math coprocessor)
Primary IDE channel
Secondary IDE channel
Note (1)
Note (1)
14
15
Note (1)
Note (1)
Note: If the “Used For” device is disabled in setup, the corresponding interrupt
is available for other devices.
KEMX-2030 User’s Manual
53
Appendix A
DMA Channels
DMA # Used For
Comment
0
1
2
3
Memory Refresh
Sound
Floppy disk controller
free
Note (1)
Note (1)
Unavailable if LPT
used in ECP mode.
4
5
6
7
Cascade
Sound
free
Note (1)
free
Note: If the "Used For" device is disabled in setup, the corresponding interrupt
is available for other devices.
Memory Mapping
Upper Memory
Used For
VGA BIOS
LAN Option ROM
Comment
No
Yes
C0000h - CBFFFh
CC000h - CFFFFh
CD000h - CDFFFh
E0000h - FFFFFh
System BIOS
No
PCI Devices
PCI Device
LAN
PCI Interrupt
INTA
Comment
AD20
PCI Express Devices
PCIe Device
PCIe Interrupt Comment
INTC
PCIe x1 Slot 1
Inter-IC Bus (I2C)
I2C Address
A0h
Used For
DDR2-RAM DIMM Socket 0
Address
Comment
ISA I/O Port
I2C Address
2Eh
Used For
Super I/O
Comment
2Eh
WatchDog Timer
Reference register in Super I/O
I/O Address Map
I/O Address
00h – 0Fh
Used For
Comment
8237DMA Controller
8259A PIC
C0h – DFh
20h, 21h
2Eh, 2Fh
A0h, A1h
SuperIO Access Port
8259A PIC
40h – 43h (XT/AT)
8254PIT
KEMX-2030 User’s Manual
54
Appendix A
44h – 47h (PS/2)
60h – 64h
90h – 96h
KeyBoard Controller
PS/2 P OS
F0h – FFh
Math Co-Processor, X87 Unit
Secondary IDE
Primary IDE
170h – 177h
1F0h – 1F7h
200h – 22Fh
220h – 22Fh
279h, A79h
GAME I/O
Sound Blaster / AD Lib
Plug and Play Configuration
Register
A15h, A16h
2E8h – 2EFh
2F8h – 2FFh
378h – 37Ah
3B0h – 3BFh
3C0h – 3CFh
3D4h – 3D9h
HW Monitor Access Port
COM4
COM2
Parallel Printer Port
MDA / MGA
EGA / VGA
CGA/CRT Register, Controller and
Palette Register
Floppy Diskette
Enhanced IDE
COM3
3F0h – 3F7h
3F6h, 3F7h
3E8h – 3EFh
3F8h – 3FFh
0CF8h
COM1
PCI Configuration Register/address
PCI Configuration Register/data
0CFCh
Hardware Monitor Parameters
IT8781F Pin Name
VIN0
Voltage/Temperature Function/Comments
+VCORE
Processor core
voltage
+/- 5%
+/- 5%
+/- 5%
+/- 5%
+/- 5%
+/- 5%
+/- 5%
VIN1
VIN2
VIN3
VIN4
VIN5
VIN6
5VSB
+1.05V
+3.3V
+5V
+12V
Chip core 1.5V
DDR 1.8V
5VSB
SYS_TEMP
CPU_TEMP
PRDCHOT#
System Temperature
CPU Temperature
CPU over
temperature
shutdown output
Beep function for
hardware monitor
BEEP
KEMX-2030 User’s Manual
55
Appendix B
Appendix B
DIO (Digital I/O) KIT User Guide
The purpose of this document is to provide detail instruction on how to install
and utilized the Quanmax DIO Tool on Microsoft Windows XP.
WARNING
The program is platform specific. Therefore, do not use the DIO Tool
to other platform to prevent adverse effect.
How to install the test program:
Go in to the “DIO KITS” folder. Double Click on the DIO installation program to
start the installation.
The installation program name will vary according to the platform which it
applied to. For example, if the platform name is KEMX-2030, the installation
program will be name as “DIO Tool for KEMX-2030.exe”.
KEMX-2030 User’s Manual
56
Appendix B
As the .NET Framework 2.0 is a prerequisite, the installation program will
prompt to install .NET Framework installation first should the .NET Framework
2.0 is not installed.
The .NET Framework 2.0 installation would take a couple minutes to finish.
Click “Next” to agree to start installation program
KEMX-2030 User’s Manual
57
Appendix B
After enter the path where you wish to install the DIO Test Package, Click
“Next” to agree to continue the installation process
Click “Next” to agree all setting made and start installation process
After the installation process is complete, click “Close” to close down the
installation program
Installation is now complete.
KEMX-2030 User’s Manual
58
Appendix B
How to run the test program:
Click on “Start”->”All Programs”->”Quanmax DIO Tool”->”DIO TOOL” to start
the DIO test program
The test tool is launch.
All output will be set to low as default value when program initialized.
Click on “Switch Output” button can switch the corresponding output.
The input readings will only be update by hitting the “Read Input” button.
CN3 to DIO Program look up table:
Pin #
2
0
4
1
6
2
8
3
10 (GND)
--
DIO Input#
Pin #
1
0
3
1
5
2
7
3
9 (+5V)
--
DIO Output #
KEMX-2030 User’s Manual
59
Appendix B
How to uninstall the test program:
From Control Panel, select the “Add or Remove Program”.
Select the “Quanmax DIO Tool”, click on “Remove” button to start the uninstall
process
Click on “Yes” button to confirm the removal of the DIO Tool Kit.
KEMX-2030 User’s Manual
60
|
