GA-965P-DS3
Intel® CoreTM 2 Extreme / CoreTM 2 Duo
Intel® Pentium® Processor Extreme Edition
Intel® Pentium® D / Pentium® 4 LGA775 Processor Motherboard
User's Manual
Rev. 1002
12ME-965PDS3-1002R
* The WEEE marking on the product indicates this product must not be disposed of with user's other household waste
and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!
* The WEEE marking applies only in European Union's member states.
Copyright
© 2006 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in the manual are legally registered to their respective companies.
Notice
The written content provided with this product is the property of Gigabyte.
No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any
means without Gigabyte's prior written permission. Specifications and features are subject to
change without prior notice.
Product Manual Classification
In order to assist in the use of this product, Gigabyte has categorized the user manual in the
following:
For quick installation, please refer to the "Hardware Installation Guide" included with the
product.
For detailed product information and specifications, please carefully read the
"Product User Manual".
For detailed information related to Gigabyte's unique features, please go to "Technology
Guide" section on Gigabyte's website to read or download the information you need.
Table of Contents
ItemChecklist ................................................................................................................. 6
OptionalAccessories ...................................................................................................... 6
GA-965P-DS3 Motherboard Layout............................................................................... 7
Block Diagram................................................................................................................ 8
Chapter 1 Hardware Installation ..................................................................................... 9
1-1 Considerations Prior to Installation .................................................................... 9
1-2 Feature Summary .......................................................................................... 10
1-3 Installation of the CPU and CPU Cooler ....................................................... 12
1-3-1 Installation of the CPU ......................................................................................... 12
1-3-2 Installation of the CPU Cooler ............................................................................ 13
1-4 Installation of Memory .................................................................................... 14
1-5 Installation of Expansion Cards ...................................................................... 16
1-6 I/O Back Panel Introduction ........................................................................... 17
1-7 ConnectorsIntroduction .................................................................................. 18
Chapter 2 BIOS Setup................................................................................................ 29
The Main Menu (For example: BIOS Ver. : F1b)...................................................... 30
2-1 Standard CMOS Features ............................................................................. 32
2-2 Advanced BIOS Features .............................................................................. 34
2-3 IntegratedPeripherals ..................................................................................... 36
2-4 Power Management Setup ............................................................................. 39
2-5 PnP/PCI Configurations................................................................................. 40
2-6 PC Health Status ........................................................................................... 41
2-7 MB Intelligent Tweaker(M.I.T.) ....................................................................... 43
2-8 Load Fail-Safe Defaults ................................................................................... 46
2-9 Load Optimized Defaults ................................................................................. 46
2-10 Set Supervisor/User Password ..................................................................... 47
2-11 Save & Exit Setup ......................................................................................... 48
2-12 Exit Without Saving ....................................................................................... 48
- 4 -
Chapter 3 Install Drivers............................................................................................. 49
3-1 Install Chipset Drivers .................................................................................... 49
3-2 SoftwareApplications ..................................................................................... 50
3-3 Driver CD Information .................................................................................... 50
3-4 Hardware Information ..................................................................................... 51
3-5 Contact Us ..................................................................................................... 51
Chapter 4 Appendix ................................................................................................... 53
4-1 Unique Software Utilities ................................................................................ 53
4-1-1 EasyTune 5 Introduction ..................................................................................... 53
4-1-2 Xpress Recovery2 Introduction ......................................................................... 54
4-1-3 Flash BIOS Method Introduction ........................................................................ 56
4-1-4 Configuring SATA Hard Drive(s) (Controller: GIGABYTE SATA2) ................ 65
4-1-5 2- / 4- / 6- / 8- Channel Audio Function Introduction ...................................... 78
4-2 Troubleshooting ............................................................................................... 83
- 5 -
Item Checklist
IDE Cable x 1 and FDD Cable x 1
SATA 3Gb/s Cable x 4
I/O Shield
* The items listed above are for reference only, and are subject to change without notice.
Optional Accessories
2 Ports USB2.0 Cable (Part Number: 12CR1-1UB030-51/R)
4 Ports USB2.0 Cable (Part Number: 12CR1-1UB030-21/R)
- 6 -
GA-965P-DS3 Motherboard Layout
CPU_FAN
ATX_12V
KB_MS
COAXIAL
OPTICAL
LGA775
ATX
Intel® P965
AUDIO
PCIE_3
PCIE_16
PCIE_1
PCIE_2
PCI1
FDD
M a r v e l l
88E8053
CLR_CMOS
Intel® ICH8
BATTERY
SATAII0
SATAII1
CODEC
GSATAII0
GSATAII1
SATAII2
SATAII3
GIGABYTE
SATA2
PCI2
IDE1
BIOS
PCI3
CD_IN
F_PANEL
CI
SPDIF_I
F_USB1 F_USB2 F_USB3
PWR_LED
- 7 -
Block Diagram
PCI-E CLK
(100MHz)
CPUCLK+/-(266/200/133MHz)
DDRII 800/667/533MHz DIMM(Note)
LGA775
Processor
Host
Interface
PCI Express x16
Intel®
P965
Dual Channel Memory
LAN
MCHCLK (266/200/133MHz)
2 SATA 3Gb/s
ATA33/66/100/133
IDE Channel
RJ45
GIGABYTE
SATA2
Marvell
88E8053
x 1
x 1
PCI Express Bus
BIOS
x 1
x 1
x 1
4 SATA 3Gb/s
Intel®
ICH8
PCI-E CLK
(100MHz)
LPT
3 PCI Express x1
Floppy
IT8718
PCI Bus
COM Port
PS/2 KB/Mouse
CODEC
10 USB
Ports
3 PCI
PCICLK
(33MHz)
(Note) To use a DDR II 800/667 memory module on the motherboard, you must install an 800/
1066MHz FSB processor.
- 8 -
Chapter 1 Hardware Installation
1-1 Considerations Prior to Installation
Preparing Your Computer
The motherboard contains numerous delicate electronic circuits and components which can
become damaged as a result of electrostatic discharge (ESD). Thus, prior to installation, please
follow the instructions below:
1. Please turn off the computer and unplug its power cord.
2. When handling the motherboard, avoid touching any metal leads or connectors.
3. It is best to wear an electrostatic discharge (ESD) cuff when handling electronic components
(CPU, RAM).
4. Prior to installing the electronic components, please have these items on top of an antistatic pad or
within a electrostatic shielding container.
5. Please verify that the power supply is switched off before unplugging the power supply connector
from the motherboard.
Installation Notices
1. Prior to installation, please do not remove the stickers on the motherboard. These stickers are required
for warranty validation.
2. Prior to the installation of the motherboard or any hardware, please first carefully read the information
in the provided manual.
3. Before using the product, please verify that all cables and power connectors are connected.
4. To prevent damage to the motherboard, please do not allow screws to come in contact with the
motherboard circuit or its components.
5. Please make sure there are no leftover screws or metal components placed on the motherboard or
within the computer casing.
6. Please do not place the computer system on an uneven surface.
7. Turning on the computer power during the installation process can lead to damage to system
components as well as physical harm to the user.
8. If you are uncertain about any installation steps or have a problem related to the use of the product,
please consult a certified computer technician.
Instances of Non-Warranty
1. Damage due to natural disaster, accident or human cause.
2. Damage as a result of violating the conditions recommended in the user manual.
3. Damage due to improper installation.
4. Damage due to use of uncertified components.
5. Damage due to use exceeding the permitted parameters.
6. Product determined to be an unofficial Gigabyte product.
- 9 -
Hardware Installation
1-2 Feature Summary
CPU
Supports LGA775 Intel® CoreTM 2 Extreme / CoreTM 2 Duo / Pentium® Proces-
sor Extreme Edition / Pentium® D / Pentium®
4
L2 cache varies with CPU
Front Side Bus
Chipset
Supports 1066/800/533MHz FSB
Northbridge: Intel® P965 Express Chipset
Southbridge: Intel® ICH8
Onboard Marvell 88E8053 phy (10/100/1000 Mbit)
Onboard Realtek ALC883 chip
Supports High Definition Audio
Supports 2 / 4 / 6 / 8 channel audio
Supports SPDIF In/Out connection
Supports CD In connection
LAN
Audio
Storage
ICH8 Southbrigde
-
-
1 FDD connector, allowing connection of 1 FDD device
4 SATA 3Gb/s connectors (SATAII0,1, 2, 3), allowing connection of 4
SATA 3Gb/s devices
Onboard GIGABYTE SATA2 chip
-
-
-
1 IDE connector (UDMA 33/ATA 66/ATA 100/ATA 133), allowing con-
nection of 2 IDE devices
2 SATA 3Gb/s connectors (GSATAII0,1), allowing connection of 2 SATA
3Gb/s devices
Supports data striping (RAID 0), mirroring (RAID 1), and JBOD for Serial
ATA
O.S Support
Memory
Microsoft Windows 2000/XP
4 DDR II DIMM memory slots (supports up to 8GB memory)
Supports dual channel DDR II 800/667/533 unbuffered DIMMs(Note 1)
Supports 1.8V DDR II DIMMs
Expanstion Slots
1
3
PCI Express x16 slot
PCI Express x1 slots
3 PCI slots
Internal Connectors
1 24-pin ATX power connector
1 4-pin ATX 12V power connector
1 floppy connector
1 IDE connector
6 SATA 3Gb/s connectors
1 CPU fan connector
1 system fan connector
1 front panel connector
1 front audio connector
1 CD In connector
3 USB 2.0/1.1 connectors for additional 6 ports by cables
1 SPDIF In connector
1 power LED connector
GA-965P-DS3 Motherboard
- 10 -
Rear Panel I/O
1 PS/2 keyboard port
1 PS/2 mouse port
1 SPDIF Out connection (coaxial+optical)
1 parallel port
4 USB 2.0/1.1 ports
1 serial port (COMA)
1 RJ-45 port
6 audio jacks (Line In / Line Out / MIC In/Surround Speaker Out (Rear
Speaker Out)/Center/Subwoofer Speaker Out/Side Speaker Out)
IT8718 chip
I/O Control
Hardware Monitor
System voltage detection
CPU / System temperature detection
CPU / System fan speed detection
CPU warning temperature
CPU / System fan failure warning
CPU Smart Fan Control
1 8M bit flash ROM
Use of licensed AWARD BIOS
Supports @BIOS
BIOS
Additional Features
Supports Download Center
Supports Q-Flash
Supports EasyTune (Note 2)
Supports Xpress Install
Supports Xpress Recovery2
Supports Xpress BIOS Rescue
Norton Internet Security (OEM revision)
ATX form factor; 30.5cm x 21.0cm
Bundle Software
Form Factor
(Note 1) To use a DDR II 800/667 memory module on the motherboard, you must install an 800/
1066MHz FSB processor.
(Note 2) EasyTune functions may vary depending on different motherboards.
- 11 -
Hardware Installation
1-3 Installation of the CPU and CPU Cooler
Before installing the CPU, please comply with the following conditions:
1. Please make sure that the motherboard supports the CPU.
2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong
direction, the CPU will not insert properly. If this occurs, please change the insert direction
of the CPU.
3. Please add an even layer of heat paste between the CPU and CPU cooler.
4. Please make sure the CPU cooler is installed on the CPU prior to system use,
otherwise overheating and permanent damage of the CPU may occur.
5. Please set the CPU host frequency in accordance with the CPU specifications. It is not
recommended that the system bus frequency be set beyond hardware specifications
since it does not meet the required standards for the peripherals. If you wish to set
the frequency beyond the proper specifications, please do so according to your hard-
ware specifications including the CPU, graphics card, memory, hard drive, etc.
HT functionality requirement content :
Enabling the functionality of Hyper-Threading Technology for your computer system requires all
of the following platform components:
- CPU: An Intel® Pentium 4 CPU with HT Technology
- Chipset: An Intel® Chipset that supports HT Technology
- BIOS: A BIOS that supports HT Technology and has it enabled
- OS: An operation system that has optimizations for HT Technology
1-3-1 Installation of the CPU
Fig. 2
Fig. 1
Metal Lever
Remove the plastic
covering on the CPU
socket.
Gently lift the metal
lever located on the
CPU socket to the
upright position.
Fig. 3
Fig. 4
Notice the small gold
colored triangle located
on the edge of the CPU
socket. Align the
Once the CPU is
properly inserted,
please replace the
load plate and push the
metal lever back into
its original position.
indented corner of the
CPU with the triangle and gently insert the CPU into
position. (Grasping the CPU firmly between your
thumb and forefinger, carefully place it into the socket
in a straight and downwards motion. Avoid twisting or
bending motions that might cause damage to the CPU
during installation.)
GA-965P-DS3 Motherboard
- 12 -
1-3-2 Installation of the CPU Cooler
Male Push Pin
The top of Female Push Pin
Female Push Pin
Fig.1
Fig. 2
Please apply an even layer of heat paste on the
surface of the installed CPU.
(Turning the push pin along the direction of arrow is to
remove the CPU cooler, on the contrary, is to install.)
Please note the direction of arrow sign on the male
push pin doesn't face inwards before installation. (This
instruction is only for Intel boxed fan)
Fig. 3
Fig. 4
Place the CPU cooler atop the CPU and make
sure the push pins aim to the pin hole on the
motherboard.Pressing down the push pins
diagonally.
Please make sure the Male and Female push pin
are joined closely. (for detailed installation
instructions, please refer to the CPU cooler instal-
lation section of the user manual)
Fig. 6
Fig. 5
Finally, please attach the power connector of the
CPU cooler to the CPU fan header located on the
motherboard.
Please check the back of motherboard after
installing. If the push pin is inserted as the picture,
the installation is complete.
The CPU cooler may adhere to the CPU as a result of hardening of the heat paste.To prevent
such an occurrence, it is suggested that either thermal tape rather than heat paste be used for
heat dissipation or using extreme care when removing the CPU cooler.
- 13 -
Hardware Installation
1-4 Installation of Memory
Before installing the memory modules, please comply with the following conditions:
1. Please make sure that the memory used is supported by the motherboard. It is
recommended that memory of similar capacity, specifications and brand be used.
2. Before installing or removing memory modules, please make sure that the computer
power is switched off to prevent hardware damage.
3. Memory modules have a foolproof insertion design. A memory module can be installed
in only one direction. If you are unable to insert the module, please switch the direction.
The motherboard supports DDR II memory modules, whereby BIOS will automatically detect memory
capacity and specifications. Memory modules are designed so that they can be inserted only in one direction.
The memory capacity used can differ with each slot.
Notch
DDR II
Fig.1
The DIMM socket has a notch, so the DIMM memory mod-
ule can only fit in one direction. Insert the DIMM memory
module vertically into the DIMM socket. Then push it down.
Fig.2
Close the plastic clip at both edges of the DIMM sockets to
lock the DIMM module.
Reverse the installation steps when you wish to remove
the DIMM module.
GA-965P-DS3 Motherboard
- 14 -
Dual Channel Memory Configuration
The GA-965P-DS3 supports the Dual Channel Technology. After operating
the Dual Channel Technology, the bandwidth of memory bus will double.
The GA-965P-DS3 includes 4 DIMM sockets, and each Channel has two
DIMM sockets as following:
Channel 0 : DDRII1, DDRII2
Channel 1 : DDRII3, DDRII4
If you want to operate the Dual Channel Technology, please note the following explanations
due to the limitation of Intel chipset specifications.
1. Dual Channel mode will not be enabled if only one DDRII memory module is installed.
2. To enable Dual Channel mode with two or four memory modules (it is recommended to
use memory modules of identical brand, size, chips, and speed), you must install them
into DIMM sockets of the same color.
The following is a Dual Channel Memory configuration table: (DS: Double Side, SS: Single Side,
X:Empty)
DDR II 1
DS/SS
X
DDR II 2
X
DDR II 3
DS/SS
X
DDR II 4
X
2 memory modules
4 memory modules
DS/SS
DS/SS
DS/SS
DS/SS
DS/SS
DS/SS
(Note) When memory modules of different size and chips are installed, a message which indicates
that memory is configured to Flex memory mode operation will appear during POST.
Intel® Flex Memory Technology offers easier upgrades by allowing different memory sizes to
be populated and remain in dual-channel mode.
- 15 -
Hardware Installation
1-5 Installation of Expansion Cards
You can install your expansion card by following the steps outlined below:
1. Read the related expansion card's instruction document before install the expansion card into the
computer.
2. Remove your computer's chassis cover, screws and slot bracket from the computer.
3. Press the expansion card firmly into expansion slot in motherboard.
4. Be sure the metal contacts on the card are indeed seated in the slot.
5. Replace the screw to secure the slot bracket of the expansion card.
6. Replace your computer's chassis cover.
7. Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS.
8. Install related driver from the operating system.
Installing a PCI Express x16 expansion card:
Please align the VGA card to the onboard
PCI Express x16 slot and press firmly
down on the slot. Make sure your VGA
card is locked by the latch at the end of
the PCI Express x16 slot. When you try
uninstall the VGA card, please gently
press the latch as the picture to the left
shows to release the card.
GA-965P-DS3 Motherboard
- 16 -
1-6 I/O Back Panel Introduction
PS/2 Keyboard and PS/2 Mouse Connector
To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard
to the lower port (purple).
LPT (Parallel Port)
The parallel port allows connection of a printer, scanner and other peripheral devices.
COAXIAL (SPDIF Out)
The SPDIF coaxial output port is capable of providing digital audio to external speakers or
compressed AC3 data to an external Dolby Digital Decoder via a coaxial cable.
OPTICAL (SPDIF Out)
The SPDIF optical output port is capable of providing digital audio to external speakers or com-
pressed AC3 data to an external Dolby Digital Decoder via an optical cable.
Serial Port (COMA)
Connects to serial-based mouse or data processing devices.
USB Port
Before you connect your device(s) into USB connector(s), please make sure your device(s) such
as USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface.
Also make sure your OS supports USB controller. If your OS does not support USB controller,
please contact OS vendor for possible patch or driver upgrade. For more information please
contact your OS or device(s) vendors.
LAN Port
The provided Internet connection is Gigabit Ethernet, providing data transfer speeds of
10/100/1000Mbps.
Center/Subwoofer Speaker Out
The default Center/Subwoofer Speaker Out jack. Center/Subwoofer speakers can be connected to
Center/Subwoofer Speaker Out jack.
Surround Speaker Out (Rear Speaker Out)
The default Surround Speaker Out (Rear Speaker Out) jack. Rear surround speakers can be
connected to Surround Speaker Out (Rear Speaker Out) jack.
Side Speaker Out
The default Side Speaker Out jack. Surround side speakers can be connected to Side Speaker Out
jack.
Line In
The default Line In jack. Devices like CD-ROM, walkman etc. can be connected to Line In jack.
- 17 -
Hardware Installation
Line Out (Front Speaker Out)
The default Line Out (Front Speaker Out) jack. Stereo speakers, earphone or front surround
speakers can be connected to Line Out (Front Speaker Out) jack.
MIC In
The default MIC In jack. Microphone must be connected to MIC In jack.
In addition to the default speakers settings, the
~
audio jacks can be reconfigured to
perform different functions via the audio software. Only microphones still MUST be connected
to the default Mic In jack ( ) . Please refer to the 2-/4-/6-/8- channel audio setup steps for
detailed software configuration information.
1-7 Connectors Introduction
1
3
2
5
4
11
16
17
8
7
12 13
14
6
15
9
10
1)
2)
3)
4)
5)
6)
7)
8)
9)
ATX_12V
10)
11)
12)
13)
14)
15)
16)
17)
F_PANEL
F_AUDIO
CD_IN
ATX (Power Connector)
CPU_FAN
SYS_FAN
SPDIF_I
FDD
F_USB1 / F_USB2 / F_USB3
IDE1
CI
SATAII0/1/2/3
GSATAII0/1
PWR_LED
CLR_CMOS
BATTERY
GA-965P-DS3 Motherboard
- 18 -
1/2) ATX_12V/ATX (Power Connector)
With the use of the power connector, the power supply can supply enough stable power to all
the components on the motherboard. Before connecting the power connector, please make sure
that all components and devices are properly installed. Align the power connector with its
proper location on the motherboard and connect tightly.
The ATX_12V power connector mainly supplies power to the CPU. If the ATX_12V power
connector is not connected, the system will not start.
Caution!
Please use a power supply that is able to handle the system voltage requirements. It is
recommended that a power supply that can withstand high power consumption be used (300W
or greater). If a power supply is used that does not provide the required power, the result can
lead to an unstable system or a system that is unable to start.
If you use a 24-pin ATX power supply, please remove the small cover on the power connector
on the motherboard before plugging in the power cord ; Otherwise, please do not remove it.
Pin No.
Definition
GND
1
2
3
4
3
1
4
2
GND
+12V
+12V
12
24
Pin No.
Definition
3.3V
Pin No.
13
Definition
1
3.3V
2
3.3V
14
-12V
3
GND
15
GND
4
+5V
16
PS_ON(soft On/Off)
5
GND
17
GND
6
+5V
18
GND
7
GND
19
GND
8
Power Good
20
-5V
9
5V SB(stand by +5V)
+12V
21
+5V
10
11
12
22
+5V
+12V(Only for 24-pin ATX)
3.3V(Only for 24-pin ATX)
23
+5V (Only for 24-pin ATX)
GND(Only for 24-pin ATX)
13
1
24
- 19 -
Hardware Installation
3/4) CPU_FAN / SYS_FAN (Cooler Fan Power Connector)
The cooler fan power connector supplies a +12V power voltage via a 4-pin power connector and
possesses a foolproof connection design.
Most coolers are designed with color-coded power connector wires. A red power connector wire
indicates a positive connection and requires a +12V power voltage. The black connector wire is
the ground wire (GND).
Remember to connect the CPU/system fan cable to the CPU_FAN/SYS_FAN connector to prevent
CPU damage or system hanging caused by overheating.
Pin No.
Definition
1
2
3
4
GND
+12V/SpeedControl
Sense
1
SpeedControl
CPU_FAN
1
SYS_FAN
5) FDD (Floppy Connector)
The FDD connector is used to connect the FDD cable while the other end of the cable connects to the
FDD drive. The types of FDD drives supported are: 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB.
Before attaching the FDD cable, please take note of the foolproof groove in the FDD connector.
34
33
2
1
GA-965P-DS3 Motherboard
- 20 -
6) IDE1 (IDE Connector)
An IDE device connects to the computer via an IDE connector. One IDE connector can connect to
one IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical
drive). If you wish to connect two IDE devices, please set the jumper on one IDE device as Master
and the other as Slave (for information on settings, please refer to the instructions located on the IDE
device). Before attaching the IDE cable, please take note of the foolproof groove in the IDE connector.
39
40
1
2
7) SATAII0/1/2/3 (SATA 3Gb/s Connector, Controlled by Intel ICH8)
SATA 3Gb/s can provide up to 300MB/s transfer rate. Please refer to the BIOS setting for the Serial
ATA and install the proper driver in order to work properly.
Pin No.
Definition
GND
TXP
1
2
3
4
5
6
7
7
1
SATAII0
SATAII1
TXN
GND
RXN
RXP
1
7
7
1
GND
SATAII2
SATAII3
1
7
- 21 -
Hardware Installation
8) GSATAII0/1 (SATA 3Gb/s Connector, Controlled by GIGABYTE SATA2)
SATA 3Gb/s can provide up to 300MB/s transfer rate. Please refer to the BIOS setting for the Serial
ATA and install the proper driver in order to work properly.
Pin No.
Definition
GND
TXP
1
2
3
4
5
6
7
7
1
1
7
GSATAII0
GSATAII1
TXN
GND
RXN
RXP
GND
9) PWR_LED
The PWR_LED connector is connected with the system power indicator to indicate whether the
system is on/off. It will blink when the system enters suspend mode.
Pin No.
Definition
MPD+
1
2
3
MPD-
1
MPD-
GA-965P-DS3 Motherboard
- 22 -
10) F_PANEL (Front Panel Jumper)
Please connect the power LED, PC speaker, reset switch and power switch etc. of your chassis
front panel to the F_PANEL connector according to the pin assignment below.
Speaker Connector
Message LED/
Power
Switch
Power/
Sleep LED
2
1
20
19
Reset Switch
IDE Hard Disk Active LED
HD (IDE Hard Disk Active LED)
(Blue)
Pin 1: LED anode(+)
Pin 2: LED cathode(-)
Pin 1: Power
SPEAK (Speaker Connector)
(Amber)
Pin 2- Pin 3: NC
Pin 4: Data(-)
RES (Reset Switch)
Open:Normal
(Green)
Close: Reset Hardware System
Open:Normal
PW (Power Switch)
(Red)
Close: Power On/Off
Pin 1: LED anode(+)
Pin 2: LED cathode(-)
NC
MSG (Message LED/Power/Sleep LED)
(Yellow)
NC ( Purple)
- 23 -
Hardware Installation
11) F_AUDIO (Front Audio Connector)
This connector supports either HD (High Definition) or AC97 front panel audio module. If you wish
to use the front audio function, connect the front panel audio module to this connector. Check the pin
assignments carefully while you connect the front panel audio module. Incorrect connection
between the module and connector will make the audio device unable to work or even damage it.
For optional front panel audio module, please contact your chassis manufacturer.
1
9
2
10
HD Audio:
AC'97Audio:
Pin No.
Definition
MIC2_L
Pin No.
Definition
MIC
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
GND
GND
MIC2_R
MIC Power
NC
-ACZ_DET
LINE2_R
FSENSE1
FAUDIO_JD
No Pin
Line Out (R)
NC
NC
No Pin
Line Out (L)
NC
LINE2_L
FSENSE2
By default, the audio driver is configured to support HD Audio. To connect an AC97 front panel
audio module to this connector, please refer to the instructions on Page 82 about the software
settings.
GA-965P-DS3 Motherboard
- 24 -
12) CD_IN (CD IN)
Connect CD-ROM or DVD-ROM audio out to the connector.
Pin No.
Definition
CD-L
1
2
3
4
1
GND
GND
CD-R
13) SPDIF_I (SPDIF In)
Use SPDIF IN feature only when your device has digital output function. Be careful with the polarity
of the SPDIF_I connector. Check the pin assignment carefully while you connect the SPDIF
cable, incorrect connection between the cable and connector will make the device unable to work
or even damage it. For optional SPDIF cable, please contact your local dealer.
Pin No.
Definition
Power
1
2
3
1
SPDIFI
GND
- 25 -
Hardware Installation
14) F_ USB1/F_USB2/F_USB3 (Front USB Connector)
Be careful with the polarity of the front USB connector. Check the pin assignment carefully while
you connect the front USB cable, incorrect connection between the cable and connector will make
the device unable to work or even damage it. For optional front USB cable, please contact your
local dealer.
Pin No.
Definition
Power(5V)
Power(5V)
USB DX-
USB Dy-
USB DX+
USB Dy+
GND
1
2
3
4
5
6
7
8
9
10
9
1
2
10
GND
No Pin
NC
15) CI (Chassis Intrusion, Case Open)
This 2-pin connector allows your system to detect if the chassis cover is removed. You can check
the "Case Opened" status in BIOS Setup.
Pin No.
Definition
Signal
GND
1
2
1
GA-965P-DS3 Motherboard
- 26 -
16) CLR_CMOS (Clear CMOS)
You may clear the CMOS data to its default values by this header. To clear CMOS, temporarily
short the two pins. Default doesn't include the jumper to avoid improper use of this header.
Open:Normal
Short: Clear CMOS
17) BATTERY
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended
by the manufacturer.
Dispose of used batteries according to the manufacturer's
instructions.
If you want to erase CMOS...
1. Turn off the computer and unplug the power cord.
2. Gently take out the battery and put it aside for about one minute.
(Or you can use a metal object to connect the positive and nega-
tive pins in the battery holder to makethem short for five seconds.)
3. Re-install the battery.
4. Plug the power cord in and turn on the computer.
- 27 -
Hardware Installation
GA-965P-DS3 Motherboard
- 28 -
Chapter 2 BIOS Setup
BIOS (Basic Input and Output System) includes a CMOS SETUP utility which allows user to configure
required settings or to activate certain system features.
The CMOS SETUP saves the configuration in the CMOS SRAM of the motherboard.
When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS
SRAM.
When the power is turned on, pushing the <Del> button during the BIOS POST (Power-On Self Test) will
take you to the CMOS SETUP screen. You can enter the BIOS setup screen by pressing "Ctrl + F1".
If you wish to upgrade to a new BIOS, either Gigabyte's Q-Flash or @BIOS utility can be used.
Q-Flash allows the user to quickly and easily update or backup BIOS without entering the operating
system.
@BIOS is a Windows-based utility that does not require users to boot to DOS before upgrading BIOS but
directly download and update BIOS from the Internet.
CONTROL KEYS
<
>< >< ><
>
Move to select item
<Enter>
<Esc>
Select Item
Main Menu - Quit and not save changes into CMOS Status Page Setup Menu
and Option Page Setup Menu - Exit current page and return to Main Menu
Increase the numeric value or make changes
Decrease the numeric value or make changes
General help, only for Status Page Setup Menu and Option Page Setup Menu
Item Help
<Page Up>
<Page Down>
<F1>
<F2>
<F5>
Restore the previous CMOS value from CMOS, only for Option Page Setup
Menu
<F6>
<F7>
<F8>
<F9>
<F10>
Load the fail-safe default CMOS value from BIOS default table
Load the Optimized Defaults
Q-Flash utility
System Information
Save all the CMOS changes, only for Main Menu
Main Menu
The on-line description of the highlighted setup function is displayed at the bottom of the screen.
Status Page Setup Menu / Option Page Setup Menu
Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selec-
tions for the highlighted item. To exit the Help Window press <Esc>.
Because BIOS flashing is potentially risky, please do it with caution and avoid inadequate
operation that may result in system malfunction.
- 29 -
BIOS Setup
<F12> : Boot Menu
Select boot sequence for onboard (or add-on cards) device.
Award Modular BIOS v6.00PG, An Energy Star Ally
Copyright (C) 1984-2005, Award Software, Inc.
Intel P965 BIOS for 965P-DS3 E6
.
.
.
.
<DEL>:BIOS Setup/Q-Flash, <F9>: Xpress Recovery2, <F12>Boot Menu
05/10/2006-P965-ICH8-6A79LG0DC-00
<F12> Boot Menu
Use < > or < > to select a device, then press enter to accept . Press <ESC> to exit this menu.
Boot Menu
== Select a Boot First device ==
Floppy
LS120
Hard Disk
CDROM
ZIP
USB-FDD
USB-ZIP
USB-CDROM
USB-HDD
LAN
KL:Move Enter :Accept ESC:Exit
The Main Menu (For example: BIOS Ver. : F1b)
Once you enter Award BIOS CMOS Setup Utility, the Main Menu (as figure below) will appear on the
screen. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu.
CMOS Setup Utility-Copyright (C) 1984-2006 Award Software
`
`
`
`
`
`
`
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Power Management Setup
PnP/PCI Configurations
PC Health Status
Save & Exit Setup
Exit Without Saving
MB Intelligent Tweaker(M.I.T.)
ESC: Quit
KLJI: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Time, Date, Hard Disk Type...
If you can't find the setting you want, please press "Ctrl+F1" to search the advanced option
hidden.
Please Load Optimized Defaults in the BIOS when somehow the system works not stable as
usual. This action makes the system reset to the default for stability.
GA-965P-DS3 Motherboard
- 30 -
Standard CMOS Features
This setup page includes all the items in standard compatible BIOS.
Advanced BIOS Features
This setup page includes all the items of Award special enhanced features.
Integrated Peripherals
This setup page includes all onboard peripherals.
Power Management Setup
This setup page includes all the items of Green function features.
PnP/PCI Configurations
This setup page includes all the configurations of PCI & PnP ISA resources.
PC Health Status
This setup page is the System auto detect Temperature, voltage, fan, speed.
MB Intelligent Tweaker(M.I.T.)
This setup page is control CPU clock and frequency ratio.
Load Fail-Safe Defaults
Fail-Safe Defaults indicates the value of the system parameters which the system would be in safe
configuration.
Load Optimized Defaults
Optimized Defaults indicates the value of the system parameters which the system would be in
best performance configuration.
Set Supervisor Password
Change, set, or disable password. It allows you to limit access to the system and Setup, or just to Setup.
Set User Password
Change, set, or disable password. It allows you to limit access to the system.
Save & Exit Setup
Save CMOS value settings to CMOS and exit setup.
Exit Without Saving
Abandon all CMOS value changes and exit setup.
- 31 -
BIOS Setup
2-1 Standard CMOS Features
CMOS Setup Utility-Copyright (C) 1984-2006 Award Software
Standard CMOS Features
Date (mm:dd:yy)
Time (hh:mm:ss)
Fri, Mar 18 2006
18:25:04
Item Help
Menu Level`
`
`
`
`
`
`
`
`
IDE Channel 0 Master
IDE Channel 1 Master
IDE Channel 2 Master
IDE Channel 3 Master
IDE Channel 4 Master
IDE Channel 4 Slave
IDE Channel 5 Master
IDE Channel 5 Slave
[None]
[None]
[None]
[None]
[None]
[None]
[None]
[None]
Change the day, month,
year
<Week>
Sun. to Sat.
<Month>
Jan. to Dec.
Drive A
Floppy 3 Mode Support
[1.44M, 3.5"]
[Disabled]
<Day>
1 to 31 (or maximum
allowed in the month)
Halt On
[All, But Keyboard]
<Year>
Base Memory
Extended Memory
Total Memory
640K
511M
512M
1999 to 2098
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save
ESC: Exit
F7: Optimized Defaults
F1: General Help
F5: Previous Values
Date
The date format is <week>, <month>, <day>, <year>.
Week
Month
Day
The week, from Sun to Sat, determined by the BIOS and is display only
The month, Jan. Through Dec.
The day, from 1 to 31 (or the maximum allowed in the month)
The year, from 1999 through 2098
Year
Time
The times format in <hour> <minute> <second>. The time is calculated base on the 24-hour
military-time clock. For example, 1 p.m. is 13:00:00.
IDE Channel 0/1 Master
IDE HDD Auto-Detection
Press "Enter" to select this option for automatic device detection.
IDE Channel 0/1 Master IDE/SATA Device Setup. You can use one of three methods:
Auto
None
Allows BIOS to automatically detect IDE/SATA devices during POST(default)
Select this if no IDE/SATA devices are used and the system will skip the
automatic detection step and allow for faster system start up.
User can manually input the correct settings
Manual
Access Mode Use this to set the access mode for the hard drive. The four options are:
CHS/LBA/Large/Auto(default:Auto)
IDE Channel 2/3 Master, IDE Channel 4/5 Master, Slave
IDE Auto-Detection
Press "Enter" to select this option for automatic device detection.
Extended IDE Drive. You can use one of the two methods:
Auto
None
Allows BIOS to automatically detect IDE/SATA devices during POST(default)
Select this if no IDE/SATA devices are used and the system will skip the
automatic detection step and allow for faster system start up.
GA-965P-DS3 Motherboard
- 32 -
Access Mode
Use this to set the access mode for the hard drive. The two options are:
Large/Auto(default:Auto)
Capacity
Cylinder
Head
Capacity of currently installed hard disk.
Number of cylinders
Number of heads
Write precomp
Precomp
Landing Zone
Sector
Landing zone
Number of sectors
Drive A
The category identifies the types of floppy disk drive A that has been installed in the computer.
None
No floppy drive installed
360K, 5.25"
1.2M, 5.25"
5.25 inch PC-type standard drive; 360K byte capacity.
5.25 inch AT-type high-density drive; 1.2M byte capacity
(3.5 inch when 3 Mode is Enabled).
720K, 3.5"
1.44M, 3.5"
2.88M, 3.5"
3.5 inch double-sided drive; 720K byte capacity
3.5 inch double-sided drive; 1.44M byte capacity.
3.5 inch double-sided drive; 2.88M byte capacity.
Floppy 3 Mode Support (for Japan Area)
Disabled
Normal Floppy Drive. (Default value)
Drive A
Drive A is 3 mode Floppy Drive.
Halt on
The category determines whether the computer will stop if an error is detected during power up.
No Errors
The system boot will not stop for any error that may be detected and you
will be prompted.
All Errors
Whenever the BIOS detects a non-fatal error the system will be stopped.
All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all other
errors. (Default value)
All, But Diskette
All, But Disk/Key
The system boot will not stop for a disk error; it will stop for all other errors.
The system boot will not stop for a keyboard or disk error; it will stop for all
other errors.
Memory
The category is display-only which is determined by POST (Power On Self Test) of the BIOS.
Base Memory
The POST of the BIOS will determine the amount of base (or conventional) memory installed
in the system.
The value of the base memory is typically 512K for systems with 512K memory installed on
the motherboard, or 640K for systems with 640K or more memory installed on the motherboard.
Extended Memory
The BIOS determines how much extended memory is present during the POST.
This is the amount of memory located above 1 MB in the CPU's memory address map.
Total Memory
This item displays the memory size that used.
- 33 -
BIOS Setup
2-2 Advanced BIOS Features
CMOS Setup Utility-Copyright (C) 1984-2006 Award Software
Advanced BIOS Features
`
Hard Disk Boot Priority
First Boot Device
[Press Enter]
[Floppy]
Item Help
Menu Level`
Second Boot Device
Third Boot Device
Password Check
[Hard Disk]
[CDROM]
[Setup]
Select Hard Disk Boot
Device Priority
(Note)
CPU Hyper-Threading
[Enabled]
[Disabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[PCI]
Limit CPUID Max. to 3 (Note)
No-Execute Memory Protect (Note)
CPU Enhanced Halt (C1E)(Note)
CPU Thermal Monitor 2(TM2) (Note)
(Note)
CPU EIST Function
Virtualization Technology(Note)
Init Display First
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save
ESC: Exit
F7: Optimized Defaults
F1: General Help
F5: Previous Values
Hard Disk Boot Priority
Select boot sequence for onboard(or add-on cards) SCSI, RAID, etc.
Use < > or < > to select a device, then press<+> to move it up, or <-> to move it down the list. Press
<ESC> to exit this menu.
First / Second / Third Boot Device
Floppy
LS120
Select your boot device priority by Floppy.
Select your boot device priority by LS120.
Select your boot device priority by Hard Disk.
Select your boot device priority by CDROM.
Select your boot device priority by ZIP.
Select your boot device priority by USB-FDD.
Select your boot device priority by USB-ZIP.
Select your boot device priority by USB-CDROM.
Select your boot device priority by USB-HDD.
Select your boot device priority by LAN.
Disable this function.
Hard Disk
CDROM
ZIP
USB-FDD
USB-ZIP
USB-CDROM
USB-HDD
LAN
Disabled
Password Check
Setup
The system will boot but will not access to Setup page if the correct
password is not entered at the prompt. (Default value)
The system will not boot and will not access to Setup page if the correct
password is not entered at the prompt.
System
If you want to cancel the setting of password, please just press ENTER to make [SETUP] empty.
(Note) This item will show up when you install a processor that supports this function.
GA-965P-DS3 Motherboard
- 34 -
CPU Hyper-Threading (Note)
Enabled
Enable CPU Hyper Threading Feature. Please note that this feature is only
working for operating system with multi processors mode supported. (Default
value)
Disabled
Disables CPU Hyper Threading.
Limit CPUID Max. to 3 (Note)
Enabled
Limit CPUID Maximum value to 3 when use older OS like NT4.
Disabled
Disable CPUID Limit for windows XP. (Default value)
No-Execute Memory Protect(Note)
Enabled
Enable No-Execute Memory Protect function. (Default value)
Disabled
Disable No-Execute Memory Protect function.
CPU Enhanced Halt (C1E)(Note)
Enabled
Enable CPU Enhanced Halt (C1E) function. (Default value)
Disabled
Disable CPU Enhanced Halt (C1E) function.
CPU Thermal Monitor 2 (TM2) (Note)
Enabled
Enable CPU Thermal Monitor 2 (TM2) function. (Default value)
Disabled
Disable CPU Thermal Monitor 2 (TM2) function.
CPU EIST Function (Note)
Enabled
Enable CPU EIST function. (Default value)
Disabled
Disable EIST function.
Virtualization Technology (Note)
Enabled
Enable Virtualization Technology. (Default value)
Disabled
Disable this function.
Init Display First
This feature allows you to select the first initiation of the monitor display from which card when you
install a PCI card and a PCI Express VGA card on the motherboard.
PEG
PCI
Set Init display first to PCI Express VGA card.
Set Init display first to PCI. (Default value)
(Note) This item will show up when you install a processor which supports this function.
- 35 -
BIOS Setup
2-3 Integrated Peripherals
CMOS Setup Utility-Copyright (C) 1984-2006 Award Software
Integrated Peripherals
SATA Port0-3 Native Mode
USB Controller
USB 2.0 Controller
USB Keyboard Support
USB Mouse Support
Legacy USB storage detect
Azalia Codec
[Disabled]
[Enabled]
[Enabled]
[Disabled]
[Disabled]
[Enabled]
[Auto]
Item Help
Menu Level`
Onboard H/W LAN
SMART LAN
[Enabled]
[Press Enter]
[Disabled]
[Enabled]
[IDE]
[3F8/IRQ4]
[378/IRQ7]
[SPP]
`
OnBoard LAN Boot ROM
Onboard SATA/IDE Device
Onboard SATA/IDE Ctrl Mode
Onboard Serial Port 1
Onboard Parallel Port
Parallel Port Mode
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save
ESC: Exit
F7: Optimized Defaults
F1: General Help
F5: Previous Values
SATA Port0-3 Native Mode
Enabled
Set SATA Port0~3 to operate at Native IDE mode.
Disabled
Set SATA Port0~3 to operate at Legacy IDE mode.(Default value)
USB Controller
Enabled
Disabled
Enable USB Controller. (Default value)
Disable USB Controller.
USB 2.0 Controller
Disable this function if you are not using onboard USB 2.0 feature.
Enabled
Disabled
Enable USB 2.0 Controller. (Default value)
Disable USB 2.0 Controller.
USB Keyboard Support
Enabled
Enable USB Keyboard Support.
Disabled
Disable USB Keyboard Support. (Default value)
USB Mouse Support
Enabled
Enable USB Mouse Support.
Disabled
Disable USB Mouse Support. (Default value)
Legacy USB storage detect
Enabled
Enable USB storage detection function in MS-DOS environment. (Default
value)
Disabled
Disable this function.
Azalia Codec
Auto
Disabled
Auto detect Azalia audio function. (Default value)
Disable Azalia audio function.
Onboard H/W LAN
Enabled
Disabled
Enable Onboard H/W LAN function. (Default value)
Disable this function.
GA-965P-DS3 Motherboard
- 36 -
SMART LAN (LAN Cable Diagnostic Function)
CMOS Setup Utility-Copyright (C) 1984-2006 Award Software
SMART LAN
Item Help
Start detecting at Port.....
Menu Level`
Pair1-2 Status
Pair3-6 Status
Pair4-5 Status
Pair7-8 Status
=
=
=
=
Normal
Normal
Normal
Normal
/
/
/
/
Length
Length
Length
Length
=
=
=
=
N/A
N/A
N/A
N/A
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F10: Save
ESC: Exit
F1: General Help
F5: Previous Values
F6: Fail-Safe Defaults
F7: Optimized Defaults
This motherboard incorporates cable diagnostic feature designed to detect the status of the attached LAN
cable. This feature will detect cabling issue and report the approximate distance to the fault or short.
Refer to the following information for diagnosing your LAN cable:
When LAN Cable Is Functioning Normally...
1. If no cable problem is detected on the LAN cable connected to a Gigabit hub, the Status fields
of Pair 1-2, Pair 3-6, Pair 4-5, and Pair 7-8 will show Normal and the Length fields will show
N/A,as shown in the figure above.
2. If no cable problem is detected on the LAN cable connected to a 10/100 Mbps hub, the Status
fields of Pair 1-2 and Pair 3-6 will show Normal and the Length fields will show N/A.
However, because Pair 4-5 and Pair 7-8 are not used in a 10/100 Mbps environment, their
Status fields will show Short or Open, and the length shown is the approximate length of the
attached LAN cable.
When a Cable Problem Occurs...
If a cable problem occurs on a specified pair of wires, the Status field will show Short or Open
and the length shown will be the approximate distance to the fault or short.
For example, if it shows Pair1-2 Status = Short / Length = 1.6m,
it means that a fault or short might occur at about 1.6m on Pair 1-2.
When No LAN Cable Is Attached...
If no LAN cable is attached to the motherboard, the Status fields of all four pairs of wires will show
Open and the Length fields show 0.0m.
- 37 -
BIOS Setup
OnBoard LAN Boot ROM
This function decide whether to invoke the boot ROM of the onboard LAN chip.
Enabled
Disabled
Enable this function.
Disable this function. (Default value)
Onboard SATA/IDE Device
This function allows users to enable or disable the SATA/IDE ports controlled by the GIGABYTE
SATA2 controller.
Enabled
Disabled
Enable this function.(Default value)
Disable this function.
OnBoard SATA/IDE Ctrl Mode
This function allows users to decide the operating mode of the SATA ports controlled by the
GIGABYTE SATA2 controller.
IDE
Set the SATA channel to IDE mode.(Default value)
AHCI
Set the SATA channel to AHCI mode. Advanced Host Controller Inter-
face (AHCI) is an interface specification that allows the storage driver to
enable advanced Serial ATA features such as Native Command Queu-
ing and hot plug. For more details about AHCI, please visit Intel's
website.
RAID/IDE
Set the SATA channel to RAID mode and IDE channel to IDE mode.
Onboard Serial Port 1
Auto
BIOS will automatically setup the port 1 address.
3F8/IRQ4
2F8/IRQ3
3E8/IRQ4
2E8/IRQ3
Enable onboard Serial port 1 and address is 3F8/IRQ4. (Default value)
Enable onboard Serial port 1 and address is 2F8/IRQ3.
Enable onboard Serial port 1 and address is 3E8/IRQ4.
Enable onboard Serial port 1 and address is 2E8/IRQ3.
Onboard Parallel port
Disabled
Disable onboard LPT port.
378/IRQ7
278/IRQ5
3BC/IRQ7
Enable onboard LPT port and address is 378/IRQ7. (Default value)
Enable onboard LPT port and address is 278/IRQ5.
Enable onboard LPT port and address is 3BC/IRQ7.
Parallel Port Mode
SPP
EPP
ECP
ECP+EPP
Using Parallel port as Standard Parallel Port. (Default value)
Using Parallel port as Enhanced Parallel Port.
Using Parallel port as Extended Capabilities Port.
Using Parallel port as ECP & EPP mode.
GA-965P-DS3 Motherboard
- 38 -
2-4 Power Management Setup
CMOS Setup Utility-Copyright (C) 1984-2006 Award Software
Power Management Setup
ACPI Suspend Type
Soft-Off by PWR-BTTN
PME Event Wake Up
Power On by Ring
[S1(POS)]
[Instant-Off]
[Enabled]
[Enabled]
[Disabled]
Everyday
0 : 0 : 0
[Disabled]
[Disabled]
Enter
Item Help
Menu Level`
Resume by Alarm
x
x
Date (of Month) Alarm
Time (hh:mm:ss) Alarm
Power On By Mouse
Power On By Keyboard
KB Power ON Password
AC Back Function
x
[Soft-Off]
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save
ESC: Exit
F7: Optimized Defaults
F1: General Help
F5: Previous Values
ACPI Suspend Type
S1(POS)
Set ACPI suspend type to S1/POS(Power On Suspend). (Default
value)
S3(STR)
Set ACPI suspend type to S3/STR(Suspend To RAM).
Soft-Off by PWR-BTTN
Instant-Off
Delay 4 Sec.
Press power button then Power off instantly. (Default value)
Press power button 4 sec. to Power off. Enter suspend if button is
pressed less than 4 sec.
PME Event Wake Up
This feature requires an ATX power supply that provides at least 1A on the 5VSB lead.
Disabled
Enabled
Disable this function.
Enable PME Event Wake up. (Default value)
Power On by Ring
Disabled
Disable Power on by Ring function.
Enabled
Enable Power on by Ring function. (Default value)
Resume by Alarm
You can set "Resume by Alarm" item to enabled and key in Date/time to power on system.
Disabled
Enabled
Disable this function. (Default value)
Enable alarm function to POWER ON system.
If Resume by Alarm is Enabled.
Date (of Month) Alarm :
Everyday, 1~31
Time (hh: mm: ss) Alarm : (0~23) : (0~59) : (0~59)
Power On By Mouse
Disabled
Disabled this function. (Default value)
Double Click
Double click on PS/2 mouse left button to power on the system.
- 39 -
BIOS Setup
Power On By Keyboard
Disabled
Disabled this function. (Default value)
Password
Keyboard 98
Enter from 1 to 5 characters to set the Keyboard Power On Password.
If your keyboard have "POWER Key" button, you can press the key to
power on the system.
KB Power ON Password
When "Power On by Keyboard" set at Password, you can set the password here.
Enter
Input password (from 1 to 5 characters) and press Enter to set the Keyboard
Power On password.
AC Back Function
Soft-Off
When AC-power back to the system, the system will be in "Off" state.
(Default value)
Full-On
Memory
When AC-power back to the system, the system always in "On" state.
When AC-power back to the system, the system will return to the Last state
before AC-power off.
2-5 PnP/PCI Configurations
CMOS Setup Utility-Copyright (C) 1984-2006 Award Software
PnP/PCI Configurations
PCI1 IRQ Assignment
PCI2 IRQ Assignment
PCI3 IRQ Assignment
[Auto]
[Auto]
[Auto]
Item Help
Menu Level`
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save
ESC: Exit
F7: Optimized Defaults
F1: General Help
F5: Previous Values
PCI1 IRQ Assignment
Auto
3,4,5,7,9,10,11,12,14,15
Auto assign IRQ to PCI 1. (Default value)
Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 1.
PCI2 IRQ Assignment
Auto
3,4,5,7,9,10,11,12,14,15
Auto assign IRQ to PCI 2. (Default value)
Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 2.
PCI3 IRQ Assignment
Auto
3,4,5,7,9,10,11,12,14,15
Auto assign IRQ to PCI 3. (Default value)
Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 3.
GA-965P-DS3 Motherboard
- 40 -
2-6 PC Health Status
CMOS Setup Utility-Copyright (C) 1984-2006 Award Software
PC Health Status
Reset Case Open Status
Case Opened
[Disabled]
No
Item Help
Menu Level`
Vcore
OK
DDR18V
OK
+3.3V
OK
+12V
OK
Current System Temperature
Current CPU Temperature
Current CPU FAN Speed
Current SYSTEM FAN Speed
CPU Warning Temperature
CPU FAN Fail Warning
SYSTEM FAN Fail Warning
FAN Speed Control Method
FAN Speed Control Mode
40oC
47oC
3375 RPM
0
[Disabled]
[Disabled]
[Disabled]
[Auto]
RPM
[Auto]
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F6: Fail-Safe Defaults
F10: Save
ESC: Exit
F7: Optimized Defaults
F1: General Help
F5: Previous Values
Reset Case Open Status
Disabled
Don't reset case open status. (Default value)
Enabled
Clear case open status at next boot.
Case Opened
If the case is closed, "Case Opened" will show "No".
If the case have been opened, "Case Opened" will show "Yes".
If you want to reset "Case Opened" value, set "Reset Case Open Status" to "Enabled" and save
CMOS, your computer will restart.
Current Voltage(V) Vcore/DDR18V/+3.3V/+12V
Detect system's voltage status automatically.
Current System/CPU Temperature
Detect system/CPU temperature automatically.
Current CPU/SYSTEM FAN Speed (RPM)
Detect CPU/system fan speed automatically.
CPU Warning Temperature
60oC / 140oF
70oC / 158oF
80oC / 176oF
90oC / 194oF
Disabled
Monitor CPU temperature at 60oC / 140oF.
Monitor CPU temperature at 70oC / 158oF.
Monitor CPU temperature at 80oC / 176oF.
Monitor CPU temperature at 90oC / 194oF.
Disable this function. (Default value)
CPU/SYSTEM FAN Fail Warning
Disabled
Disable the fan fail warning function. (Default value)
Enabled
Enable the fan fail warning function.
- 41 -
BIOS Setup
FAN Speed Control Method (Note)
Auto
BIOS sets the optimal CPU fan speed automatically. (Default Value)
Intel(R) QST Control the fan speed with Intel® QST (Intel® Quiet System Technology).
Legacy
Disable
CPU fan runs at different speed depending on CPU temperature.
CPU fan runs at full speed.
FAN Speed Control Mode
Auto
BIOS autodetects the type of CPU fan you installed and sets the optimal fan
speed control mode for it. (Default Value)
Voltage
PWM
Set to Voltage when you use a CPU fan with a 3-pin fan power cable.
Set to PWM when you use a CPU fan with a 4-pin fan power cable.
Note: In fact, the Voltage option can be used for CPU fans with 3-pin or 4-pin power cables.
However, some 4-pin CPU fan power cables are not designed following Intel 4-Wire fans PWM
control specifications. With such CPU fans, selecting PWM will not effectively reduce the fan
speed.
(Note) Before setting this item to Intel(R) QST, make sure at least DDRII1 or DDRII2 socket in Channel
0 is populated. A small portion of system memory will be shared when Intel® QST is enabled.
GA-965P-DS3 Motherboard
- 42 -
2-7 MB Intelligent Tweaker(M.I.T.)
CMOS Setup Utility-Copyright (C) 1984-2006 Award Software
MB Intelligent Tweaker(M.I.T.)
CPU Clock Ratio (Note)
C.A.M
[16X]
[High]
Item Help
Menu Level`
(Note)
CPU Host Clock Control
CPU Host Frequency (Mhz)
PCI Express Frequency (Mhz)
C.I.A. 2
System Memory Multiplier
Memory Frequency (Mhz)
DIMM OverVoltage Control
PCI-E OverVoltage Control
FSB OverVoltage Control
(G)MCH OverVoltage Control
CPU Voltage Control
[Disabled]
200
Auto
[Disabled]
[Auto]
533
[Normal]
[Normal]
[Normal]
[Normal]
[Normal]
1.3875V
x
Normal CPU Vcore
KLJI: Move
Enter: Select
+/-/PU/PD: Value
F10: Save
ESC: Exit
F1: General Help
F5: Previous Values
F6: Fail-Safe Defaults
F7: Optimized Defaults
Incorrect using these features may cause your system broken. For power end-user use only.
CPU Clock Ratio (Note)
This setup option will automatically assign by CPU detection.
The option will display "Locked" and read only if the CPU ratio is not changeable.
C.A.M (Note)
High
Low
Set clock ratio for frequency-locked CPU to High. (Default value)
Set clock ratio for frequency-locked CPU to Low.
CPU Host Clock Control
Please note that if your system is overclocked and cannot restart, please wait 20secs.
for automatic system restart or clear the CMOS setup data and perform a safe restart.
Disabled
Enabled
Disable CPU Host Clock Control. (Default value)
Enable CPU Host Clock Control.
CPU Host Frequency (Mhz)
100MHz ~ 600MHz
Set CPU Host Frequency from 100 MHz to 600 MHz.
If you use a 533 MHz FSB processor, set "CPU Host Frequency" to 133 MHz.
If you use a 800 MHz FSB processor, set "CPU Host Frequency" to 200 MHz.
If you use a 1066 MHz FSB processor, set "CPU Host Frequency" to 266 MHz.
Incorrect using it may cause your system broken. For power End-User use only!
PCI Express Frequency (Mhz)
Auto
Set PCI Express frequency automatically. (Default value)
90~150
Set PCI Express frequency from 90 MHz to 150 MHz.
(Note) This item will show up when you install a processor which supports this function.
- 43 -
BIOS Setup
C.I.A.2
C.I.A.2 (CPU Intelligent Acelerator 2) is designed to detect CPU loading during software program
executing, and automatically adjust CPU computing power to maximize system performance.
Disabled
Cruise
Disable this function. (Default value)
Set C.I.A.2 to Cruise. (Automatically increase CPU frequency(5%,7%) by
CPU loading.
Sports
Racing
Turbo
Set C.I.A.2 to Sports. (Automatically increase CPU frequency(7%,9%) by
CPU loading.
Set C.I.A.2 to Racing. (Automatically increase CPU frequency(9%,11%) by
CPU loading.
Set C.I.A.2 to Turbo. (Automatically increase CPU frequency(15%,17%) by
CPU loading.
Full Thrust
Set C.I.A.2 to Full Thrust. (Automatically increase CPU frequency(17%, 19%)
by CPU loading.
Warning: Stability is highly dependent on system components.
System Memory Multiplier
Wrong frequency may make system can't boot, clear CMOS to overcome wrong frequency issue.
for FSB(Front Side Bus) frequency=533 Mhz,
3.00
4.00
2.00
2.66
3.33
2.50
Auto
Memory Frequency = Host clock X 3.00.
Memory Frequency = Host clock X 4.00.
Memory Frequency = Host clock X 2.00.
Memory Frequency = Host clock X 2.66.
Memory Frequency = Host clock X 3.33.
Memory Frequency = Host clock X 2.50.
Set Memory frequency by DRAM SPD data. (Default value)
for FSB(Front Side Bus) frequency=800 MHz,
2.00
2.66
3.33
4.00
2.50
3.00
Auto
Memory Frequency = Host clock X 2.00.
Memory Frequency = Host clock X 2.66.
Memory Frequency = Host clock X 3.33.
Memory Frequency = Host clock X 4.00.
Memory Frequency = Host clock X 2.50.
Memory Frequency = Host clock X 3.00.
Set Memory frequency by DRAM SPD data. (Default value)
for FSB(Front Side Bus) frequency=1066 MHz,
2.00
2.50
3.00
2.66
3.33
4.0+
Auto
Memory Frequency = Host clock X 2.00.
Memory Frequency = Host clock X 2.50.
Memory Frequency = Host clock X 3.00.
Memory Frequency = Host clock X 2.66.
Memory Frequency = Host clock X 3.33.
Memory Frequency = Host clock X 4.0+.
Set Memory frequency by DRAM SPD data. (Default value)
Memory Frequency (Mhz)
The values depend on CPU Host Frequency (Mhz) and System Memory Multiplier setting.
GA-965P-DS3 Motherboard
- 44 -
DIMM OverVoltage Control
Please note that by overclocking your system through the increase of the DIMM voltage, damage
to the memory may occur.
Normal
+0.1V
+0.2V
+0.3V
+0.4V
+0.5V
+0.6V
Set DIMM OverVoltage Control to Normal. (Default value)
Set DIMM OverVoltage Control to +0.1V.
Set DIMM OverVoltage Control to +0.2V.
Set DIMM OverVoltage Control to +0.3V.
Set DIMM OverVoltage Control to +0.4V.
Set DIMM OverVoltage Control to +0.5V.
Set DIMM OverVoltage Control to +0.6V.
Incorrect using it may cause your system broken. For power End-User use only!
PCI-E OverVoltage Control
Normal
+0.1V
+0.2V
+0.3V
Set PCI-E OverVoltage Control to Normal. (Default value)
Set PCI-E OverVoltage Control to +0.1V.
Set PCI-E OverVoltage Control to +0.2V.
Set PCI-E OverVoltage Control to +0.3V.
FSB OverVoltage Control
Normal
+0.1V
+0.2V
+0.3V
Set FSB OverVoltage Control to Normal. (Default value)
Set FSB OverVoltage Control to +0.1V.
Set FSB OverVoltage Control to +0.2V.
Set FSB OverVoltage Control to +0.3V.
(G) MCH OverVoltage Control
Normal
+0.1V
+0.2V
+0.3V
Set (G) MCH OverVoltrage Control to Normal. (Default value)
Set (G) MCH OverVoltrage Control to +0.1V.
Set (G) MCH OverVoltrage Control to +0.2V.
Set (G) MCH OverVoltrage Control to +0.3V.
Incorrect using it may cause your system broken. For power End-User use only!
CPU Voltage Control
Supports adjustable CPU Vcore. The adjustable range is dependent on CPUs. (Default value:
Normal)
Please note that by overclocking your system through the increase of the CPU voltage, damage
to the CPU or decrease in the CPU life expectancy may occur.
Normal CPU Vcore
Display your CPU vcore voltage.
- 45 -
BIOS Setup
2-8 Load Fail-Safe Defaults
CMOS Setup Utility-Copyright (C) 1984-2006 Award Software
`
`
`
`
`
`
`
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Power Management Setup
PnP/PCI C
PC Health Status
Load Fail-Safe Defaults (Y/N)? N
Exit Without Saving
MB Intelligent Tweaker(M.I.T.)
ESC: Quit
KLJI: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Load Fail-Safe Defaults
Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum system
performance.
2-9 Load Optimized Defaults
CMOS Setup Utility-Copyright (C) 1984-2006 Award Software
`
`
`
`
`
`
`
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Power Management Setup
PnP/PCI C
PC Health Status
Load Optimized Defaults (Y/N)? N
Exit Without Saving
MB Intelligent Tweaker(M.I.T.)
ESC: Quit
KLJI: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Load Optimized Defaults
Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically
detects.
GA-965P-DS3 Motherboard
- 46 -
2-10 Set Supervisor/User Password
CMOS Setup Utility-Copyright (C) 1984-2006 Award Software
`
`
`
`
`
`
`
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Power Management Setup
PnP/PCI C
Enter Password:
PC Health tt
t
MB Intelligent Tweaker(M.I.T.)
ESC: Quit
KLJI: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Change/Set/Disable Password
When you select this function, the following message will appear at the center of the screen to assist
you in creating a password.
Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the
password. Type the password again and press <Enter>. You may also press <Esc> to abort the
selection and not enter a password.
To disable password, just press <Enter> when you are prompted to enter password. A message
"PASSWORD DISABLED" will appear to confirm the password being disabled. Once the password is
disabled, the system will boot and you can enter Setup freely.
The BIOS Setup program allows you to specify two separate passwords:
SUPERVISOR PASSWORD and a USER PASSWORD. When disabled, anyone may access all BIOS
Setup program function. When enabled, the Supervisor password is required for entering the BIOS
Setup program and having full configuration fields, the User password is required to access only basic
items.
If you select "System" at "Password Check" in Advance BIOS Features Menu, you will be prompted
for the password every time the system is rebooted or any time you try to enter Setup Menu.
If you select "Setup" at "Password Check" in Advance BIOS Features Menu, you will be prompted only
when you try to enter Setup.
- 47 -
BIOS Setup
2-11 Save & Exit Setup
CMOS Setup Utility-Copyright (C) 1984-2006 Award Software
`
`
`
`
`
`
`
Standard CMOS Features
Advanced BIOS Features
Integrate
Load Fail-Safe Defaults
Load Optimized Defaults
Save to CMOS and EXIT (Y/N)? Y
Power M
PnP/PCI Configurations
PC Health Status
Save & Exit Setup
Exit Without Saving
MB Intelligent Tweaker(M.I.T.)
ESC: Quit
KLJI: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Save Data to CMOS
Type "Y" will quit the Setup Utility and save the user setup value to RTC CMOS.
Type "N" will return to Setup Utility.
2-12 Exit Without Saving
CMOS Setup Utility-Copyright (C) 1984-2006 Award Software
`
`
`
`
`
`
`
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Quit Without Saving (Y/N)? N
Power Man
PnP/PCI Configurations
PC Health Status
Save & Exit Setup
Exit Without Saving
MB Intelligent Tweaker(M.I.T.)
ESC: Quit
KLJI: Select Item
F8: Q-Flash
F10: Save & Exit Setup
Abandon all Data
Type "Y" will quit the Setup Utility without saving to RTC CMOS.
Type "N" will return to Setup Utility.
GA-965P-DS3 Motherboard
- 48 -
Chapter 3 Install Drivers
Pictures below are shown in Windows XP.
Insert the driver CD-title that came with your motherboard into your CD-ROM drive, the driver
CD-title will auto start and show the installation guide. If not, please double click the CD-ROM
device icon in "My computer", and execute the Run.exe.
3-1 Install Chipset Drivers
After insert the driver CD, "Xpress Install" will scan automatically the system and then list all the drivers that
recommended to install. Please pick the item that you want and press "install" followed the item; or you can
press "Xpress Install" to install all items defaulted.
Some device drivers will restart your system automatically. After restarting
your system the "Xpress Install" will continue to install other drivers.
System will reboot automatically after install the drivers, afterward you can
install others application.
For USB2.0 driver support under Windows XP operating system, please
use Windows Service Pack. After install Windows Service Pack, it will show
a question mark "?" in "Universal Serial Bus controller" under "Device
Manager". Please remove the question mark and restart the system (System
will auto-detect the right USB2.0 driver).
- 49 -
Install Drivers
3-2 Software Applications
This page displays all the tools that Gigabyte developed and some free software, you can choose anyone
you want and press "install" to install them.
3-3 Driver CD Information
This page lists the contents of software and drivers in this CD-title.
GA-965P-DS3 Motherboard
- 50 -
3-4 Hardware Information
This page lists all device you have for this motherboard.
3-5 Contact Us
Please see the last page for details.
- 51 -
Install Drivers
GA-965P-DS3 Motherboard
- 52 -
Chapter 4 Appendix
4-1 Unique Software Utilities
(Not all model support these Unique Software Utilities, please check your MB features.)
4-1-1 EasyTune 5 Introduction
EasyTune 5 presents the most convenient Windows based system performance enhancement and
manageability utility. Featuring several powerful yet easy to use tools such as 1) Overclocking for enhancing
system performance, 2) C.I.A. and M.I.B. for special enhancement for CPU and Memory, 3) Smart-Fan
control for managing fan speed control of both CPU cooling fan and North-Bridge Chipset cooling fan, 4) PC
health for monitoring system status.(Note)
User Interface Overview
Button / Display
Overclocking
Description
Enters the Overclocking setting page
1.
2.
3.
4.
5.
6.
7.
8.
9.
C.I.A./C.I.A.2 and M.I.B./M.I.B.2 Enters the C.I.A./2 and M.I.B./2 setting page
Smart-Fan
PC Health
GO
"Easy Mode" & "Advance Mode"
Display screen
Function display LEDs
GIGABYTE Logo
Enters the Smart-Fan setting page
Enters the PC Health setting page
Confirmation and Execution button
Toggles between Easy and Advance Mode
Display panel of CPU frequency
Shows the current functions status
Log on to GIGABYTE website
TM
10. Help button
11. Exit or Minimize button
Display EasyTune 5 Help file
TM
Quit or Minimize EasyTune 5 software
(Note) EasyTune 5 functions may vary depending on different motherboards.
- 53 -
Appendix
4-1-2 Xpress Recovery2 Introduction
Xpress Recovery2 is designed to provide quick backup and restora-
tion of hard disk data. Supporting Microsoft operating systems including
Windows XP/2000/NT/98/Me and DOS, and file systems including
FAT16, FAT32, and NTFS, Xpress Recovery2 is able to back up data
on hard disks on PATA and SATA IDE controllers. After Xpress Recovery2 is executed from CD-ROM
for the first time, it will stay permanent in your hard disk. If you wish to run Xpress Recovery2 later, you
can simply press F9 during system bootup to enter Xpress Recovery2 without the CD-ROM.
System requirements:
1. Intel x86 platforms
2. At least 64M bytes of system memory
3. VESA-supported VGA cards
How to use the Xpress Recovery2
Initial access by booting from CD-ROM and subsequent access by pressing the F9 key:
Steps: After entering BIOS Setup, go to Advanced BIOS Feature and set to boot from CD-ROM. Save
the settings and exit the BIOS Setup. Insert the provided driver CD into your CD-ROM drive. Upon
system restart, the message which says "Boot from CD/DVD:" will appear in the bottom left corner
of the screen. Press any key to enter Xpress Recovery2.
After the steps above are completed, subsequent access to Xpress Recovery2 can be made
by simply pressing the <F9> key during system power-on.
.
.
Boot from CD/DVD:
Press any key to startup XpressRecovery2.....
Boot from CD/DVD:
Award Modular BIOS v6.00PG, An Energy Star Ally
Copyright (C) 1984-2005, Award Software, Inc.
Intel P965 BIOS for 965P-DS3 E6
.
.
.
.
<DEL>:BIOS Setup/Q-Flash, <F9>: Xpress Recovery2, <F12>For Boot Menu
<F9> Xpress Recovery2
05/10/2006-P965-ICH8-6A79LG0DC-00
1. If you have already entered Xpress Recovery2 by booting from the CD-ROM, you can
enter Xpress Recovery2 by pressing the <F9> key in the future.
2. System storage capacity and the reading/writing speed of the hard disk will affect
the data backup speed.
3. It is recommended that Xpress Recovery2 be immediately installed once you com-
plete installations of OS and all required drivers as well as software.
GA-965P-DS3 Motherboard
- 54 -
The Main Screen of Xpress Recovery2
1. RESTORE:
Restore the backed-up data to your hard disk.
(This button will not appear if there is no backup
file.)
2. BACKUP:
Back up data from hard disk.
3. REMOVE:
Remove previously-created backup files
to release disk space.
(This button will not appear if there is no backup
file.)
4. REBOOT:
Exit the main screen and restart the system.
Limitations:
1. Not compatible to Xpress Recovery.
2. For the use of Xpress Recovery2, a primary partition must be reserved.
3. Xpress Recovery2 will store the backup file at the end of the hard disk, so free space available
on the hard disk for the backup file must be allocated in advance. (A minimum 4GB is recom-
mended but the actual space is dependent on the size of the data to be backed up)
4. Capable of backing up hard disks installed with Windows operating systems including DOS and
Windows XP/2000/NT/9x/Me.
5. USB hard disks are currently not supported.
6. Does not support RAID/AHCI (class code 0104/0106) hard disks.
7. Capable of backing up and restoring only the first physical hard disk.
Hard disks detection sequence is as follows:
a. PATA IDE primary channel
b. PATA IDE secondary channel
c. SATA IDE channel 1
d. SATA IDE channel 2
e. SATA IDE channel 3
f. SATA IDE channel 4
Precautions:
1. When using hard disks with more than 128G under Windows 2000, be sure to execute the
EnableBigLba.exe program from the driver CD before data backup.
2. It is normal that data backup takes longer time than data restoration.
3. Xpress Recovery2 is compliant with the GPL regulations.
4. On a few motherboards based on Nvidia chipsets, BIOS update is required for Xpress Recovery2
to correctly identify RAID and SATA IDE mode. Please contact your motherboard manufacturer.
- 55 -
Appendix
4-1-3 Flash BIOS Method Introduction
Method 1 : Q-FlashTM Utility
Q-FlashTM is a BIOS flash utility embedded in Flash ROM. With this utility,
users only have to stay in the BIOS menu when they want to update
BIOS. Q-FlashTM allows users to flash BIOS without any utility in
DOS or Windows. Using Q-FlashTM indicates no more fooling around with any complicated instructions
and operating system since it is in the BIOS menu.
Please note that because updating BIOS has potential risk, please do it with caution!! We are
sorry that Gigabyte Technology Co., Ltd is not responsible for damages of system because of
incorrect manipulation of updating BIOS to avoid any claims from end-users.
Before You Begin:
Before you start updating BIOS with the Q-FlashTM utility, please follow the steps below first.
1. Download the latest BIOS for your motherboard from Gigabyte's website.
2. Extract the BIOS file downloaded and save the BIOS file (the one with model name.Fxx. For
example, 8KNXPU.Fba) to a floppy disk.
3. Reboot your PC and press Del to enter BIOS menu.
The BIOS upgrading guides below are separated into two parts.
If your motherboard has dual-BIOS, please refer to Part One.
If your motherboard has single-BIOS, please refer to Part Two.
Part One:
Updating BIOS with Q-FlashTM Utility on Dual BIOS Motherboards.
Some of Gigabyte motherboards are equipped with dual BIOS. In the BIOS menu of the motherboards
supporting Q-Flash and Dual BIOS, the Q-Flash utility and Dual BIOS utility are combined in the same
screen. This section only deals with how to use Q-Flash utility.
In the following sections, we take GA-8KNXP Ultra as the example to guide you how to flash BIOS
from an older version to the latest version. For example, from Fa3 to Fba.
Award Modular BIOS v6.00PG, An Energy Star Ally
Copyright (C) 1984-2003, Award Software, Inc.
Intel i875P AGPset BIOS for 8KNXP Ultra Fa3
Check System Health OK , VCore = 1.5250
Main Processor : Intel Pentium(R) 4 1.6GHz (133x12)
<CPUID : 0F27 Patch ID : 0027>
The BIOS file is Fa3
before updating
Memory Testing : 131072K OK
Memory Frequency 266 MHz in Single Channel
Primary Master : FUJITSU MPE3170AT ED-03-08
Primary Slave : None
Secondary Master : CREATIVEDVD-RM DVD1242E BC101
Secondary Slave : None
Press DEL to enter SETUP / Dual BIOS / Q-Flash / F9 For
Xpress Recovery
08/07/2003-i875P-6A79BG03C-00
GA-965P-DS3 Motherboard
- 56 -
Entering the Q-FlashTM utility:
Step1: To use Q-Flash utility, you must press Del in the boot screen to enter BIOS menu.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Select Language
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Power Management Setup
PnP/PCI Configurations
PC Health Status
Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)
Exit Without Saving
ESC: Quit
F3: Change Language
F10: Save & Exit Setup
F8: Dual BIOS/Q-Flash
Time, Date, Hard Disk Type...
Step 2: Press F8 button on your keyboard and then Y button to enter the Dual BIOS/Q-Flash utility.
Exploring the Q-FlashTM / Dual BIOS utility screen
The Q-Flash / Dual BIOS utility screen consists of the following key components.
Dual BIOS Utility
Boot From......................................... Main Bios
Dual BIOS utility bar
Main ROM Type/Size.............................SST 49LF003A
Backup ROM Type/Size.........................SST 49LF003A
512K
512K
Task menu for
Dual BIOS
utility
Wide Range Protection Disable
Boot From Main Bios
Auto Recovery Enable
Halt On Error Disable
Copy Main ROM Data to Backup
Load Default Settings
Save Settings to CMOS
Q-FlashTM utility title
bar
Q-Flash Utility
Load Main BIOS from Floppy
Load Backup BIOS from Floppy
Save Main BIOS to Floppy
Save Backup BIOS to Floppy
Task menu for
Q-FlashTM utility
Enter : Run
ꢁꢂ:Move
ESC:Reset
F10:Power Off
Action bar
Task menu for Dual BIOS utility:
Contains the names of eight tasks and two item showing information about the BIOS ROM type. Blocking a
task and pressing Enter key on your keyboard to enable execution of the task.
Task menu for Q-Flash utility:
Contains the names of four tasks. Blocking a task and pressing Enter key on your keyboard to enable execu-
tion of the task.
Action bar:
Contains the names of four actions needed to operate the Q-Flash/Dual BIOS utility. Pressing the buttons
mentioned on your keyboards to perform these actions.
- 57 -
Appendix
Using the Q-FlashTM utility:
This section tells you how to update BIOS using the Q-Flash utility. As described in the "Before you begin"
section above, you must prepare a floppy disk having the BIOS file for your motherboard and insert it to your
computer. If you have already put the floppy disk into your system and have entered the Q-Flash utility,
please follow the steps below to flash BIOS.
Steps:
1. Press arrow buttons on your keyboard to move the light bar to "Load Main BIOS from Floppy" item in
the Q-Flash menu and press Enter button.
Later, you will see a box pop up showing the BIOS files you previously downloaded to the floppy disk.
If you want to save the current BIOS for backup purpose, you can begin Step 1 with "Save Main
BIOS to Floppy" item.
2. Move to the BIOS file you want to flash and press Enter.
In this example, we only download one BIOS file to the floppy disk so only one BIOS file,
8KNXPU.Fba, is listed.
Please confirm again you have the correct BIOS file for your motherboard.
Dual BIOS Utility
Boot From.........................................
Main Bios
Main ROM Type/Size.............................SST 49LF003A
Backup ROM Type/Size.........................SST 49LF003A
512K
512K
Wide Range Protection Disable
1 file(s) found
Boo
8KNXPU.Fba
512K
BIOS file in the floppy
disk.
Total size : 1.39M
Free size : 911.50K
DEL : Delete
F5 : Refresh
Save Settings to CMOS
Q-Flash Utility
Load Main BIOS from Floppy
Load Backup BIOS from Floppy
Save Main BIOS to Floppy
Save Backup BIOS to Floppy
Enter : Run
ꢁꢂ:Move
ESC:Reset
F10:Power Off
After pressing Enter, you'll then see the progress of reading the BIOS file from the floppy disk.
Dual BIOS Utility
Boot From.........................................
Main Bios
Main ROM Type/Size.............................SST 49LF003A
Backup ROM Type/Size.........................SST 49LF003A
512K
512K
Wide Range Protection Disable
Reading BIOS file from floppy ...
Don't Turn Off Power or Reset System
Do not turn off power or
reset your system at this
stage!!
>>>>>>>>>>>>>>.....................
Save Settings to CMOS
Q-Flash Utility
Load Main BIOS from Floppy
Load Backup BIOS from Floppy
Save Main BIOS to Floppy
Save Backup BIOS to Floppy
Enter : Run
ꢁꢂ:Move
ESC:Reset
F10:Power Off
After BIOS file is read, you'll see a confirmation dialog box asking you "Are you sure to update BIOS?"
GA-965P-DS3 Motherboard - 58 -
3. Press Y button on your keyboard after you are sure to update BIOS.
Then it will begin to update BIOS. The progress of updating BIOS will be displayed.
Please do not take out the floppy disk when it begins flashing BIOS.
4. Press any keys to return to the Q-Flash menu when the BIOS updating procedure is completed.
Dual BIOS Utility
Boot From.........................................
Main Bios
Main ROM Type/Size.............................SST 49LF003A
Backup ROM Type/Size.........................SST 49LF003A
512K
512K
Wide Range Protection Disable
You can repeat Step 1 to
4 to flash the backup
BIOS, too.
!! Copy BIOS completed - Pass !!
Please press any key to continue
Save Settings to CMOS
Q-Flash Utility
Load Main BIOS from Floppy
Load Backup BIOS from Floppy
Save Main BIOS to Floppy
Save Backup BIOS to Floppy
Enter : Run
ꢁꢂ:Move
ESC:Reset
F10:Power Off
5. Press Esc and then Y button to exit the Q-Flash utility. The computer will restart automatically after
you exit Q-Flash.
Dual BIOS Utility
Boot From.........................................
Main Bios
Main ROM Type/Size.............................SST 49LF003A
Backup ROM Type/Size.........................SST 49LF003A
512K
512K
Wide Range Protection Disable
Are you sure to RESET ?
[Enter] to continure or [Esc] to abort...
Save Settings to CMOS
Q-Flash Utility
Load Main BIOS from Floppy
Load Backup BIOS from Floppy
Save Main BIOS to Floppy
Save Backup BIOS to Floppy
Enter : Run
ꢁꢂ:Move
ESC:Reset
F10:Power Off
After system reboots, you may find the BIOS version on your boot screen becomes the one you flashed.
Award Modular BIOS v6.00PG, An Energy Star Ally
Copyright (C) 1984-2003, Award Software, Inc.
Intel i875P AGPset BIOS for 8KNXP Ultra Fba
The BIOS file
Check System Health OK , VCore = 1.5250
Main Processor : Intel Pentium(R) 4 1.6GHz (133x12)
<CPUID : 0F27 Patch ID : 0027>
becomes Fab after
Memory Testing : 131072K OK
updating.
Memory Frequency 266 MHz in Single Channel
Primary Master : FUJITSU MPE3170AT ED-03-08
Primary Slave : None
Secondary Master : CREATIVEDVD-RM DVD1242E BC101
Secondary Slave : None
Press DEL to enter SETUP / Dual BIOS / Q-Flash / F9 For
Xpress Recovery
09/23/2003-i875P-6A79BG03C-00
- 59 -
Appendix
6. Press Del to enter BIOS menu after system reboots. When you are in BIOS menu, move to
Load Optimized Defaults item and press Enter to load BIOS Optimized Defaults. Normally the
system redetects all devices after BIOS has been upgraded. Therefore, we highly recommend
reloading the BIOS defaults after BIOS has been upgraded.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Power Management Setup
PnP/PCI Con
PC Health St
Select Language
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Load Optimized Defaults (Y/N)? Y
Exit Without Saving
MB Intelligent Tweaker(M.I.T.)
ESC: Quit
F3: Change Language
F10: Save & Exit Setup
F8: Dual BIOS/Q-Flash
Load Optimized Defaults
Press Y on your keyboard to load defaults.
7. Select Save & Exit Setup item to save the settings to CMOS and exit the BIOS menu.
System will reboot after you exit the BIOS menu. The procedure is completed.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Select Language
Load Fail-Safe Defaults
Load Optimized Defaults
Power Manag
PnP/PCI Con
PC Health Status
Save to CMOS and EXIT (Y/N)? Y
Save & Exit Setup
Exit Without Saving
MB Intelligent Tweaker(M.I.T.)
ESC: Quit
F3: Change Language
F8: Dual BIOS/Q-Flash
F10: Save & Exit Setup
Save Data to CMOS
Press Y on your keyboard to save and exit.
Part Two:
Updating BIOS with Q-FlashTM Utility on Single-BIOS Motherboards.
This part guides users of single-BIOS motherboards how to update BIOS using the Q-FlashTM utility.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Standard CMOS Features
Advanced BIOS Features
Integrated Peripherals
Top Performance
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Power Management Setup
PnP/PCI Configurations
PC Health Status
Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)
Exit Without Saving
ESC: Quit
F3: Change Language
F10: Save & Exit Setup
F8: Q-Flash
Time, Date, Hard Disk Type...
GA-965P-DS3 Motherboard
- 60 -
Exploring the Q-FlashTM utility screen
The Q-FlashBIOS utility screen consists of the following key components.
Q-FlashTM utility bar
Q-Flash Utility V1.30
Flash Type/Size.................................SST 49LF003A
256K
Keep DMI Data Enable
Task menu for
Q-FlashTM utility
Update BIOS from Floppy
Save BIOS to Floppy
Enter : Run
ꢁꢂ:Move
ESC:Reset
F10:Power Off
Action bar
Task menu for Q-Flash utility:
Contains the names of three tasks. Blocking a task and pressing Enter key on your keyboard to enable
execution of the task.
Action bar:
Contains the names of four actions needed to operate the Q-Flash utility. Pressing the buttons mentioned on
your keyboards to perform these actions.
Using the Q-FlashTM utility:
This section tells you how to update BIOS using the Q-Flash utility. As described in the "Before you begin"
section above, you must prepare a floppy disk having the BIOS file for your motherboard and insert it to your
computer. If you have already put the floppy disk into your system and have entered the Q-Flash utility,
please follow the steps below to flash BIOS.
Steps:
1. Press arrow buttons on your keyboard to move the light bar to "Update BIOS from Floppy" item in the
Q-Flash menu and press Enter button.
Later, you will see a box pop up showing the BIOS files you previously downloaded to the floppy disk.
If you want to save the current BIOS for backup purpose, you can begin Step 1 with "Save BIOS
to Floppy" item.
2. Move to the BIOS file you want to flash and press Enter.
In this example, we only download one BIOS file to the floppy disk so only one BIOS file,
8GE800.F4, is listed.
Please confirm again you have the correct BIOS file for your motherboard.
Q-Flash Utility V1.30
Flash Type/Size.................................SST 49LF003A
256K
1 file(s) found
8GE800.F4
256K
BIOS file in the floppy
disk.
Total size : 1.39M
En
Free size : 1.14M
DEL : Delete
er Off
F5 : Refresh
Q-Flash Utility V1.30
Flash Type/Size.................................SST 49LF003A
256K
Do not turn off power or
reset your system at
this stage!!
Reading BIOS file from floppy ...
>>>>>>>>>>>>>>.....................
En
er Off
Don't Turn Off Power or Reset System
After BIOS file is read, you'll see a confirmation dialog box asking you "Are you sure to update BIOS?"
Please do not take out the floppy disk when it begins flashing BIOS.
- 61 -
Appendix
3. Press Y button on your keyboard after you are sure to update BIOS.
Then it will begin to update BIOS. The progress of updating BIOS will be shown at the same time.
Q-Flash Utility V1.30
Flash Type/Size.................................SST 49LF003A
256K
Updating BIOS Now
Do not turn off power or
reset your system
at this stage!!
>>>>>>>>>>>>>>>>>>>.........................
En
er Off
Don't Turn Off Power or Reset System
4. Press any keys to return to the Q-Flash menu when the BIOS updating procedure is completed.
Q-Flash Utility V1.30
Flash Type/Size.................................SST 49LF003A
256K
!! Copy BIOS completed - Pass !!
Please press any key to continue
En
er Off
5. Press Esc and then Y button to exit the Q-Flash utility. The computer will restart automatically after
you exit Q-Flash.
Q-Flash Utility V1.30
Flash Type/Size.................................SST 49LF003A
256K
Are you sure to RESET ?
[Enter] to continure or [Esc] to abort...
En
er Off
After system reboots, you may find the BIOS version on your boot screen becomes the one you flashed.
Award Modular BIOS v6.00PG, An Energy Star Ally
Copyright (C) 1984-2003, Award Software, Inc.
Intel 845GE AGPSet BIOS for 8GE800 F4
The BIOS file
Check System Health OK
Main Processor : Intel Pentium(R) 4 1.7GHz (100x17.0)
<CPUID : 0F0A Patch ID : 0009>
Memory Testing : 122880K OK + 8192K Shared Memory
becomes F4 after
updating
Primary Master : FUJITSU MPE3170AT ED-03-08
Primary Slave : None
Secondary Master : CREATIVEDVD-RM DVD1242E BC101
Secondary Slave : None
Press DEL to enter SETUP / Q-Flash
03/18/2003-I845GE-6A69YG01C-00
6. Press Del to enter BIOS menu after system reboots and "Load BIOS Optimized Defaults". See how
to Load BIOS Optimized Defaults, please kindly refer to Step 6 to 7 in Part One.
Congratulation!! You have updated BIOS successfully!!
GA-965P-DS3 Motherboard
- 62 -
Method 2 : @BIOSTM Utility
If you do not have a DOS startup disk, we recommend that you use the
new @BIOS utility. @BIOS allows users to update their BIOS under
Windows. Just select the desired @BIOS server to download the latest
version of BIOS.
Fig 1. Installing the @BIOS utility
Fig 2. Installation Complete and Run @BIOS
Click Start/ Programs/ Gigabyte/ BIOS/ @BIOS
Select @BIOS item than click Install
Fig 3. The @BIOS Utility
Fig 4. Select the desired @BIOS server
Click "Update New BIOS"
Click "3"
1. Methods and steps:
I. Update BIOS through Internet
a. Click "Internet Update" icon
b. Click "Update New BIOS" icon
c. Select @BIOSTM sever
d. Select the exact model name on your motherboard
e. System will automatically download and update the BIOS.
II. Update BIOS NOT through Internet:
a. Do not click "Internet Update" icon
b. Click "Update New BIOS"
c. Please select "All Files" in dialog box while opening the old file.
d. Please search for BIOS unzip file, downloading from internet or any other methods (such
as: 965P-DS3.F1).
e. Complete update process following the instruction.
- 63 -
Appendix
III. Save BIOS
In the very beginning, there is "Save Current BIOS" icon shown in dialog box. It means to save the
current BIOS version.
IV. Check out supported motherboard and Flash ROM:
In the very beginning, there is "About this program" icon shown in dialog box. It can help you check out
which kind of motherboard and which brand of Flash ROM are supported.
2. Note:
I. In method I, if it shows two or more motherboard's model names to be selected, please make
sure your motherboard's model name again. Selecting wrong model name will cause the
system unbooted.
II. In method II, be sure that motherboard's model name in BIOS unzip file are the same as your
motherboard's. Otherwise, your system won't boot.
III. In method I, if the BIOS file you need cannot be found in @BIOSTM server, please go onto
Gigabyte's web site for downloading and updating it according to method II.
IV. Please note that any interruption during updating will cause system unbooted.
V. Do not use @BIOS and C.O.M. (Corporate Online Management) at the same time.
GA-965P-DS3 Motherboard
- 64 -
4-1-4 Configuring SATA Hard Drive(s) (Controller: GIGABYTE SATA2)
To configure SATA hard drive(s), follow the steps below:
(1) Install SATA hard drive(s) in your system.
(2) Configure SATA controller mode and boot sequence in BIOS Setup.
(3) Configure RAID array in RAID BIOS.(Note 1)
(4) Make a floppy disk containing the SATA controller driver. (Note 2)
(5) Install the SATA controller driver during OS installation. (Note 2)
Before you begin
Please prepare:
(a) At least two SATA hard drives (to ensure optimal performance, it is recommended that you use two
hard drives with identical model and capacity). If you do not want to create RAID, you may prepare
only one hard drive.
(b) An empty formatted floppy disk.
(c) Windows XP/2000 setup disk.
(d) Driver CD for your motherboard.
(1) Installing SATA hard drive(s) in your computer
Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available
SATA port(s) on the motherboard. If your motherboard has more than one SATA controller, refer to the
connectors introduction section of the user's manual to identify the SATA controller for the connector. For
example, on the GA-965P-DS3 motherboard, the GSATAII0 and GSATAII1 connectors are supported by
the GIGABYTE SATA2 controller. Then connect the power connector from your power supply to the
hard drive.
(Note 1) Skip this step if you do not want to create RAID array on the SATA controller.
(Note 2) Required when the SATA controller is set to AHCI or RAID Mode
- 65 -
Appendix
(2) Configuring SATA controller mode and boot sequence in BIOS Setup
Make sure to configure the SATA controller mode correctly in system BIOS Setup and set the first boot
device.
Step 1:
Turn on your computer and press Del to enter BIOS Setup during POST (Power-On Self Test). In BIOS
Setup, go to Integrated Periperals, ensure that the Onboard SATA/IDE Device is enabled. Then set
Onboard SATA/IDE Ctrl Mode to RAID/IDE before configuring RAID. If you do not want to create
RAID, set this item to IDE or AHCI, depending on your need (Figure 1).
CMOS Setup Utility-Copyright (C) 1984-2006 Award Software
Integrated Peripherals
SATA Port0-3 Native Mode
USB Controller
USB 2.0 Controller
USB Keyboard Support
USB Mouse Support
Legacy USB storage detect
Azalia Codec
[Disabled]
[Enabled]
[Enabled]
[Disabled]
[Disabled]
[Enabled]
[Auto]
Item Help
Menu Levelꢀ
Onboard H/W LAN
[Enabled]
[Disabled]
[Enabled]
[RAID/IDE]
[3F8/IRQ4]
[378/IRQ7]
[SPP]
OnBoard LAN Boot ROM
Onboard SATA/IDE Device
Onboard SATA/IDE Ctrl Mode
Onboard Serial Port 1
Onboard Parallel Port
Parallel Port Mode
ꢁꢂꢃꢄ: Move
Enter: Select
+/-/PU/PD: Value
F10: Save
ESC: Exit
F1: General Help
F5: Previous Values
F6: Fail-Safe Defaults
F7: Optimized Defaults
Figure 1
The BIOS Setup menus described in this section may not show the exact settings for your
motherboard. The actual BIOS Setup menu options you will see shall depend on the motherboard
you have and the BIOS version.
GA-965P-DS3 Motherboard
- 66 -
Step 2:
To boot from Windows installation CD-ROM disk, set First Boot Device under the Advanced BIOS
Features menu to CDROM (Figure 2).
CMOS Setup Utility-Copyright (C) 1984-2006 Award Software
Advanced BIOS Features
ꢀ
Hard Disk Boot Priority
First Boot Device
Second Boot Device
Third Boot Device
Password Check
[Press Enter]
[CDROM]
[Hard Disk]
[CDROM]
[Setup]
Item Help
Menu Levelꢀ
Select Hard Disk Boot
Device Priority
CPU Hyper-Threading
Limit CPUID Max. to 3
No-Execute Memory Protect
CPU Enhanced Halt (C1E)
CPU Thermal Monitor 2(TM2)
CPU EIST Function
[Enabled]
[Disabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[PCI]
Virtualization Technology
Init Display First
ꢁꢂꢃꢄ: Move
Enter: Select
+/-/PU/PD: Value
F10: Save
ESC: Exit
F1: General Help
F5: Previous Values
F6: Fail-Safe Defaults
F7: Optimized Defaults
Figure 2
Step 3:
Save and exit BIOS Setup.
GA-965P-DS3 Motherboard
- 67 -
(3) Configuring RAID array in RAID BIOS
Enter the RAID BIOS setup utility to configure a RAID array. Skip this step if you do not want to create
RAID.
Step 1:
After the POST memory test begins and before the operating system boot begins, look for a message
which says "Press <Ctrl-G> to enter RAID Setup Utility" (Figure 3). Press CTRL+ G to enter the
GIGABYTE RAID BIOS setup utility.
GIGA-BYTE Technology Corp. PCIE-to-SATAII/IDE RAID Controller BIOS v1.06.53
HDD0
HDD1
:
:
ST3120026AS
ST3120026AS
120 GB
120 GB
Non-RAID
Non-RAID
Press <Ctrl-G> to enter RAID Setup Utility ...
Figure 3
In the main screen of the GIGABYTE RAID BIOS utility (Figure 4), use the UP or DOWN ARROW key
to highlight through choices. Highlight the item that you wish to execute and press ENTER.
GIGA-BYTE Technology Corp. PCIE-to-SATAII/IDE RAID Controller BIOS V1.06.53
[ Main Menu ]
[ Hard Disk Drive List ]
Create RAID Disk Drive
Delete RAID Disk Drive
Revert HDD to Non-RAID
Solve Mirror Conflict
Rebuild Mirror Drive
Save And Exit Setup
Mode Name
HDD0: ST3120026AS
HDD1: ST3120026AS
Capacity
120 GB
120 GB
Type/Status
Non-RAID
Non-RAID
Exit Without Saving
[ RAID Disk Drive List ]
[ꢄꢃTAB]-Switch Window
[ꢁꢂ]-Select ITEM
[ENTER]-Action
[ESC]-Exit
Figure 4
Note: In the main screen, you can select a hard disk in the Hard Disk Drive List block and press
ENTER. This allows you to check detailed information about the selected hard disk.
- 68 -
Appendix
A. Create Array:
In the main screen, press ENTER on the Create RAID Disk Drive item. Then the RAID creation screen
appears (Figure 5).
GIGA-BYTE Technology Corp. PCIE-to-SATAII/IDE RAID Controller BIOS V1.06.53
[ Create New RAID ]
[ Hard Disk Drive List ]
Name: GRAID
Level: 0-Stripe
Disks: Select Disk
Block: 128KB
Mode Name
HDD0: ST3120026AS
HDD1: ST3120026AS
Available
120 GB
120 GB
Type/Status
Non-RAID
Non-RAID
Size:
240GB
Confirm Creation
[ Help ]
[ RAID Disk Drive List ]
Enter RAID Name
Enter a string between 1 to 16 characters
in length for the created RAID drive to be
identified by system BIOS or OS.
[ꢄꢃ]-Move Cursor
[DEL,BS]-Delete Character
[ENTER]-Next
[ESC]-Abort
Figure 5
In the RAID creation screen, the Create New RAID block displays all the items that need to be set for
creating an array (Figure 5). The following procedure uses RAID 0 creation as an example.
Steps:
1. Enter Array Name: Under the Name item, enter an array name with 1~16 letters (letters cannot be
special characters) and press ENTER.
2. Select RAID Mode: Under the Level item, use UP or DOWN ARROW key to select RAID 0 (Stripe),
RAID 1 (Mirror), or JBOD (Figure 6). Then press ENTER to move onto the next step.
GIGA-BYTE Technology Corp. PCIE-to-SATAII/IDE RAID Controller BIOS V1.06.53
[ Create New RAID ]
[ Hard Disk Drive List ]
Mode Name
HDD0: ST3120026AS
HDD1: ST3120026AS
Available
120 GB
120 GB
Type/Status
Non-RAID
Non-RAID
Name: GRAID
Level: 0-Stripe
Disks: Select Disk
Block: 128KB
Size:
240GB
Confirm Creation
[ Help ]
[ RAID Disk Drive List ]
Select RAID Level
RAID 0
RAID 1
JBOD
-
-
-
Data striped for performance
Data mirrored for redundancy
Data concatenated for huge
temporarily disk required
[ꢁꢂ]-Switch RAID Level
[ENTER]-Next
[ESC]-Abort
Figure 6
GA-965P-DS3 Motherboard
- 69 -
3. Assign Array Disks: After RAID mode is selected, RAID BIOS automatically assigns the two hard
disks installed as the RAID disks.
4. Set Block Size (only for RAID 0): Under the Block item, use the UP or DOWN ARROW key to
select the block size (Figure 7), ranging from 4K to 128K. Press ENTER when finished.
GIGA-BYTE Technology Corp. PCIE-to-SATAII/IDE RAID Controller BIOS V1.06.53
[ Create New RAID ]
[ Hard Disk Drive List ]
Name: GRAID
Level: 0-Stripe
Disks: Select Disk
Block: 128KB
Mode Name
Available
120 GB
120 GB
Type/Status
Non-RAID
Non-RAID
ꢀ
ꢀ
HDD0:
HDD1:
ST3120026AS
ST3120026AS
Size:
240GB
Confirm Creation
[ Help ]
[ RAID Disk Drive List ]
Setting Stripe Block
Select a stripe size which will be used to
divide data from/to seperate RAID members.
The following are typical values:
RAID 0-128KB
[ꢁꢂ]-Switch RAID Block Size
[ENTER]-Next
[ESC]-Abort
Figure 7
5. Set Array Size: Under the Size item, type the size of the array (Figure 8), and press ENTER.
GIGA-BYTE Technology Corp. PCIE-to-SATAII/IDE RAID Controller BIOS V1.06.53
[ Create New RAID ]
[ Hard Disk Drive List ]
Name: GRAID
Level: 0-Stripe
Disks: Select Disk
Block: 128KB
Mode Name
Available
120 GB
120 GB
Type/Status
Non-RAID
Non-RAID
ꢀ
ꢀ
HDD0:
HDD1:
ST3120026AS
ST3120026AS
Size:
240GB
Confirm Creation
[ Help ]
[ RAID Disk Drive List ]
Setting RAID Capacity
Enter the RAID capacity. The default value
indicates the maximum capacity determined
by the selected members. If less than the
maximum capacity is chosen, the remaining
capacity would be no used.
[ꢄꢃ]-Switch Unit
[DEL,BS]-Delete Number
[ENTER]-Next
[ESC]-Abort
Figure 8
- 70 -
Appendix
6. Confirm Creation: After all of the items are configured, the selection bar automatically jumps to the
Confirm Creation item. When prompted to confirm your selections (Figure 9), press Y to confirm
or N to abort.
GIGA-BYTE Technology Corp. PCIE-to-SATAII/IDE RAID Controller BIOS V1.06.53
[ Create New RAID ]
[ Hard Disk Drive List ]
Name: GRAID
Level: 0-Stripe
Disks: Select Disk
Block: 128KB
Mode Name
Available
120 GB
120 GB
Type/Status
Non-RAID
Non-RAID
ꢀ
ꢀ
HDD0:
HDD1:
ST3120026AS
ST3120026AS
Size:
240GB
Confirm Creation
[ RAID Disk Dri
Create RAID on the select HDD(Y/N)?Y
CONFIRM RAID CREATION
ALL DATA ON THE SELECTED HARD DISK
WILL BE LOST WHEN EXIT WITH SAVING
[ꢄꢃ]-Switch Unit
[DEL,BS]-Delete Number
[ENTER]-Next
[ESC]-Abort
Figure 9
When finished, the new RAID array will be displayed in the RAID Disk Drive List block (Figure 10).
GIGA-BYTE Technology Corp. PCIE-to-SATAII/IDE RAID Controller BIOS V1.06.53
[ Main Menu ]
[ Hard Disk Drive List ]
Create RAID Disk Drive
Delete RAID Disk Drive
Revert HDD to Non-RAID
Solve Mirror Conflict
Rebuild Mirror Drive
Save And Exit Setup
Mode Name
HDD0: ST3120026AS
HDD1: ST3120026AS
Capacity Type/Status
120 GB RAID Inside
120 GB RAID Inside
Exit Without Saving
[ RAID Disk Drive List ]
Model Name
RDD0: GRAID
RAID Level
0-Stripe
Capacity Status
240 GB Normal
Members(HDDx)
01
[ꢄꢃTAB]-Switch Window
[ꢁꢂ]-Select RAID
[ENTER]-Action
[ESC]-Exit
Figure 10
GA-965P-DS3 Motherboard
- 71 -
To check more detailed information about the array, use the TAB key while in the Main Menu block to
move the selection bar to the RAID Disk Drive List block. Select the array and press ENTER.
A small window displaying the array information will appear in the center of the screen (Figure 11).
GIGA-BYTE Technology Corp. PCIE-to-SATAII/IDE RAID Controller BIOS V1.06.53
[ Main Menu ]
[ Hard Disk Drive List ]
Create RAID Disk Drive
Delete RAID Disk Drive
Revert HDD to Non-RAID
Solve Mirror Conflict
Rebuild Mirror Drive
Save And Exit Setup
Mode Name
HDD0: ST3120026AS
HDD1: ST3120026AS
Capacity Type/Status
120 GB RAID Inside
120 GB RAID Inside
[ RAID Information ]
Name: GRAID
Level: 0-Stripe
Block: 128KB
Exit Without Saving
Capacity: 81GB
[ RAID Disk Drive List ]
Model Name
RDD0: GRAID
tus
Members(HDDx)
01
Members: HDD 01
mal
Status: Normal
[ꢄꢃTAB]-Switch Window
[ꢁꢂ]-Select RAID
[ENTER]-Detail
[ESC]-Exit
Figure 11
After configuring the RAID array, select the Save And Exit Setup item in the main screen to save your
settings if you wish to exit the RAID BIOS utility, then press Y (Figure 12).
GIGA-BYTE Technology Corp. PCIE-to-SATAII/IDE RAID Controller BIOS V1.06.53
[ Main Menu ]
[ Hard Disk Drive List ]
Create RAID Disk Drive
Delete RAID Disk Drive
Revert HDD to Non-RAID
Solve Mirror Conflict
Rebuild Mirror Drive
Save And Exit Setup
Mode Name
HDD0: ST3120026AS
HDD1: ST3120026AS
Capacity Type/Status
120 GB RAID Inside
120 GB RAID Inside
Exit Without Saving
Save to Disk & Exit (Y/N)?Y
[ RAID Disk Drive
Model Name
RDD0: GRAID
0-Stripe
240 GB Normal
bers(HDDx)
01
[ꢄꢃTAB]-Switch Window
[ꢁꢂ]-Select ITEM
[ENTER]-Action
[ESC]-Exit
Figure 12
- 72 -
Appendix
B. Delete Array:
To delete the array, select Delete RAID Disk Drive in the main menu and press ENTER. The selection
bar will move to the RAID Disk Drive List block. Press the SPACEBAR on the array to be deleted; a
small triangle will appear to mark the selected array (Figure 13). Press Del.
GIGA-BYTE Technology Corp. PCIE-to-SATAII/IDE RAID Controller BIOS V1.06.53
[ Main Menu ]
[ Hard Disk Drive List ]
Create RAID Disk Drive
Delete RAID Disk Drive
Revert HDD to Non-RAID
Solve Mirror Conflict
Rebuild Mirror Drive
Save And Exit Setup
Mode Name
HDD0: ST3120026AS
HDD1: ST3120026AS
Capacity
120 GB
120 GB
Type/Status
Inside
Inside
Exit Without Saving
[ RAID Disk Drive List ]
Model Name
RDD0: GRAID
RAID Level
0-Stripe
Capacity Status
240 GB Normal
Members(HDDx)
01
ꢀ
[ꢁꢂ]-Select RAID
[SPACE]-Mark Delete
[DEL]-Confirm
[ESC]-Abort
Figure 13
Press Y to confirm yes to the following message (Figure 14) or N to cancel.
GIGA-BYTE Technology Corp. PCIE-to-SATAII/IDE RAID Controller BIOS V1.06.53
[ Main Menu ]
[ Hard Disk Drive List ]
Create RAID Disk Drive
Delete RAID Disk Drive
Revert HDD to Non-RAID
Solve Mirror Conflict
Rebuild Mirror Drive
Save And Exit Setup
Mode Name
HDD0: ST3120026AS
HDD1: ST3120026AS
Capacity
120 GB
120 GB
Type/Status
Inside
Inside
Exit Without Saving
ALL DATA ON THE RAID WILL LOST!!
ARE YOU SURE TO DELETE (Y/N)? N
[ RAID Disk Drive List
Model Name
RDD0: GRAID
Members(HDDx)
01
ꢀ
[ꢁꢂ]-Select RAID
[SPACE]-Mark Delete
[DEL]-Confirm
[ESC]-Abort
Figure 14
- 73 -
Appendix
(4) Making a SATA Driver Disk (Required for AHCI and RAID Mode)
To install operating system onto a serial ATA hard disk successfully, you need to install the SATA
controller driver during OS installation. Without the driver, the hard disk may not be recognized during
the Windows setup process. First of all, copy the driver for the SATA controller from the motherboard
driver CD-ROM to a floppy disk. See the instructions below about how to copy the driver in MS-DOS
mode(Note1). Prepare a startup disk that has CD-ROM support and a blank formatted floppy disk.
Step 1: Insert the prepared startup disk and motherboard driver CD-ROM in your system. Boot from the
startup disk. Once at the A:\> prompt, change to the CD-ROM drive (example: D:\>). At the D:\>
prompt, type the following two commands. Press ENTER after each command (Figure 15):
cd bootdrv
menu
Step 2: When the controller menu (Figure 16) appears, remove the startup disk and insert the blank
formatted disk. Select the controller driver by pressing the corresponding letter from the menu.
For example, from the menu in Figure 16, press E to select (E) GIGABYTE SATA-RAID Driver. Your
system will then automatically zip and transfer this driver file to the floppy disk. Press 0 to exit when
finished.
Figure 15
Figure 16
(Note 1) For users without a startup disk:
Use an alternative system and insert the GIGABYTE motherboard driver CD-ROM. From the
CD-ROM drive folder, double click the MENU.exe file in the BootDrv folder (Figure 17). A
command prompt window will open similar to that in Figure 16.
Figure 17
GA-965P-DS3 Motherboard
- 74 -
(5) Installing SATA controller driver during OS installation (Required for AHCI
and RAID Mode)
Now that you have prepared the SATA driver disk and configured BIOS settings, you are ready to install
Windows 2000/XP onto your SATA hard drive with the SATA driver. The following is an example of
Windows XP installation.
Step 1: Restart your system to boot from the Windows 2000/XP Setup disk and press F6 as soon as
you see the "Press F6 if you need to install a 3rd party SCSI or RAID driver" message (Figure 18). After
pressing F6, there will be a few moments of some files being loaded before you see the next screen.
Windows Setup
Press F6 if you need to install a 3rd party SCSI or RAID driver.
Figure 18
Step 2:
When a screen similar to that below appears, insert the floppy disk containing the SATA driver and press
S (Figure 19).
Windows Setup
Setup could not determine the type of one or more mass storage devices
installed in your system, or you have chosen to manually specify an adapter.
Currently, Setup will load support for the following mass storage devices(s)
<none>
* To specify additional SCSI adapters, CD-ROM drives, or special
disk controllers for use with Windows, including those for
which you have a device support disk from a mass storage device
manufacturer, press S.
* If you do not have any device support disks from a mass storage
device manufacturer, or do not want to specify additional
mass storage devices for use with Windows, press ENTER.
S=Specify Additional Device ENTER=Continue F3=Exit
Figure 19
- 75 -
Appendix
Step 3:
When Setup correctly recognizes the driver in the floppy disk, a controller menu similar to Figure 20
below will appear. Use the ARROW keys to select one of the items displayed depending on the
operating system to be installed. For example, select GIGABYTE GBB36X Controller (Windows
2K/XP/2003) if you wish to install Windows XP (32-Bit). Then press ENTER.
Windows Setup
You have chosen to configure a SCSI Adapter for use with Windows,
using a device support disk provided by an adapter manufacturer.
Select the SCSI Adapter you want from the following list, or press ESC
to return to the previous screen.
GIGABYTE GBB36X Controller (Windows 2K/XP/2003)
GIGABYTE GBB36X Controller (Windows XP/2003 64bit)
ENTER=Select F3=Exit
Figure 20
If a message appears saying one or some file(s) cannot be found, please check the floppy disk
or copy the correct SATA driver again from the motherboard driver CD.
Step 4:
When the next screen (Figure 21) appears, press ENTER to continue the SATA driver installation from
the floppy disk.
Windows Setup
Setup will load support for the following mass storage device(s):
GIGABYTE GBB36X Controller (Windows 2K/XP/2003)
* To specify additional SCSI adapters, CD-ROM drives, or special
disk controllers for use with Windows, including those for
which you have a device support disk from a mass storage device
manufacturer, press S.
* If you do not have any device support disks from a mass storage
device manufacturer, or do not want to specify additional
mass storage devices for use with Windows, press ENTER.
S=Specify Additional Device ENTER=Continue F3=Exit
Figure 21
GA-965P-DS3 Motherboard
- 76 -
After the SATA controller driver installation is completed, you can proceed with the Windows 2000/XP
installation.
WindowsXP Professional Setup
Welcome to Setup.
This port of the Setup program prepares Microsoft(R)
Windows (R) XP to run on your computer.
To set up Windows XP now, press ENTER.
To repair a Windows XP installation using
Recovery Console, press R.
To quit Setup without installing Windows XP, press F3.
Enter= Continue R=Repair
F3=Exit
Figure 22
(Note: Each time you add a new hard drive to a RAID array, the RAID driver will have to be installed
under Windows once for that hard drive. After that, the driver will not have to be installed.)
- 77 -
Appendix
4-1-5 2- / 4- / 6- / 8- Channel Audio Function
Introduction
The default speaker settings for the 6 audio jacks are
as shown in the picture to the right. The jack
retasking capability supported by HD Audio allows
users to change the function for each audio jack by
Center/Subwoofer
Speaker Out
Line In
Line Out
(Front Speaker Out)
Rear Speaker Out
the audio software provided. For example, if
a
Side Speaker
Out
Mic In
rear speaker is plugged into the center/subwoofer
speaker out jack, you can change the center/
subwoofer speaker out jack to fucntion as a rear
speaker out jack via the audio software.Please
follow the steps to install the function. (Following
pictures are in Windows XP)
Note that if you wish to connect a microphone, you MUST connect it to the default Mic In jack
for the microphone to work correctly.
HD Audio
With multiple built-in high quality digital-to-analog converters (DACs) that support audio output at up to
192 kHz/24-bit quality and multi-streaming applications, HD Audio is able to handle multiple audio
streams (in and out) simultaneously. Multi-channel audio experiences have become a reality so you
can, for instance, listen to MP3 music, have an Internet chat, make a telephone call over the Internet,
and etc. all at the same time.
Stereo Speakers Connection and Settings:
We recommend that you use the speaker with amplifier to acquire the best sound effect if the stereo
output is applied.
STEP 1 :
After installation of the audio driver, you should find
an Audio Manager icon in your system tray (you
can also find the icon in Control Panel). Double-
click the icon to open the Audio Control Panel.
GA-965P-DS3 Motherboard
- 78 -
STEP 2:
In the Audio Control Panel, click the Audio I/O
tab. In the upper left list, click 2CH Speaker.
STEP 3:
After a speaker or headphone is plugged into the
rear Line Out jack, a small window will pop up and
ask you what type of equipment is connected.
Choose Headphone or Line Out depending on
the device connected and click OK. The 2-chan-
nel audio setup is completed.
4 Channel Audio Setup
STEP 1 :
After installation of the audio driver, you should find
an Audio Manager icon in your system tray (you
can also find the icon in Control Panel). Double-
click the icon to open the Audio Control Panel.
STEP 2:
In the Audio Control Panel, click the Audio I/O
tab. In the upper left list, click 4CH Speaker.
- 79 -
Appendix
STEP 3:
After plugging in 4-channel speakers to the rear
speaker jacks, a small window will pop up and
ask you what type of equipment is connected.
Choose a device depending on the type of speaker
connected (4-channel audio consists of Front
Speaker Out (Line Out) and Rear Speaker Out) and
then click OK. The 4-channel audio setup is
completed.
6 Channel Audio Setup
STEP 1 :
After installation of the audio driver, you should find
an Audio Manager icon in your system tray (you
can also find the icon in Control Panel). Double-
click the icon to open the Audio Control Panel.
STEP 2:
In the Audio Control Panel, click the Audio I/O
tab. In the upper left list, click 6CH Speaker.
STEP 3:
After plugging in 6-channel speakers to the rear
speaker jacks, a small window will pop up and
ask you what type of equipment is connected.
Choose a device depending on the type of speaker
connected (6-channel audio consists of Front
Speaker Out (Line Out), Rear Speaker Out, and
Center/Subwoofer Speaker Out) then click OK.
The 6-channel audio setup is completed.
GA-965P-DS3 Motherboard
- 80 -
8 Channel Audio Setup
STEP 1 :
After installation of the audio driver, you should find
an Audio Manager icon in your system tray (you
can also find the icon in Control Panel). Double-
click the icon to open the Audio Control Panel.
STEP 2:
In the Audio Control Panel, click the Audio I/O
tab. In the upper left list, click 8CH Speaker.
STEP 3:
After plugging in 8-channel speakers to the rear
speaker jacks, a small window will pop up and
ask you what type of equipment is connected.
Choose a device depending on the type of speaker
connected (8-channel audio consists of Front
Speaker Out (Line Out), Rear Speaker Out, Cen-
ter/Subwoofer Speaker Out, and Side Speaker Out)
then click OK. The 8-channel audio setup is
completed.
- 81 -
Appendix
Sound Effect Configuration:
At the Sound Effect menu, users can adjust sound
option settings as desired.
AC'97 Audio Configuration:
To enable the front panel audio connector to sup-
port AC97 Audio mode, go to the Audio Control
Panel and click the Audio I/O tab. In the ANA-
LOG area, click the Tool icon and then select the
Disable front panel jack detection check box.
This action completes the AC'97 Audio configuration.
GA-965P-DS3 Motherboard
- 82 -
4-2 Troubleshooting
Below is a collection of general asked questions. To check general asked questions based on a specific
motherboard model, please log on to GIGABYTE's website.
Question 1: I cannot see some options that were included in previous BIOS after updating BIOS. Why?
Answer: Some advanced options are hidden in new BIOS version. Please press Ctrl and F1 keys after
entering BIOS menu and you will be able to see these options.
Questions 2: Why is the light of my keyboard/optical mouse still on after computer shuts down?
Answer: In some boards, a small amount of electricity is kept on standby after computer shuts down and
that's why the light is still on.
Question 3: How do I clear CMOS?
Answer: If your board has a Clear CMOS jumper, please refer to the Clear CMOS steps in the manual. If your
board doesn't have such jumper, you can take off the on-board battery to leak voltage to clear CMOS.
Please refer to the steps below:
Steps:
1. Turn off power.
2. Disconnect the power cord from MB.
3. Take out the battery gently and put it aside for about 1 minute (Or you can use a metal object
to connect the positive and negative pins in the battery holder to makethem short for 5
seconds).
4. Re-insert the battery to the battery holder.
5. Connect power cord to MB again and turn on power.
6. Press Del to enter BIOS and load Fail-Safe Defaults(or load Optimized Defaults).
7. Save changes and reboot the system.
Question 4: Why do I still get a weak sound after turning up the speaker to the maximum volume?
Answer: Please make sure the speaker you are using is equipped with an internal amplifier. If not, please
change another speaker with power/amplifier and try again later.
Question 5: Sometimes I hear different continuous beeps from computer after system boots up. What do
these beeps usually stand for?
Answer: The beep codes below may help you identify the possible computer problems. However, they are
only for reference purposes. The situations might differ from case to case.
ꢃ
AWARD BIOS Beep Codes
1 short: System boots successfully
2 short: CMOS setting error
1 long 1 short: DRAM or M/B error
1 long 2 short: Monitor or display card error
1 long 3 short: Keyboard error
1 long 9 short: BIOS ROM error
Continuous long beeps: DRAM error
Continuous short beeps: Power error
- 83 -
Appendix
GA-965P-DS3 Motherboard
- 84 -
- 85 -
Appendix
GA-965P-DS3 Motherboard
- 86 -
Contact Us
y
Taiwan (Headquarters)
y
China
GIGA-BYTE TECHNOLOGY CO., LTD.
Address: No.6, Bau Chiang Road, Hsin-Tien,
Taipei 231, Taiwan
NINGBO G.B.T. TECH. TRADING CO., LTD.
Shanghai
TEL:+886-2-8912-4888
TEL:+86-21-63410999
FAX:+86-21-63410100
Beijing
FAX:+886-2-8912-4003
Tech. and Non-Tech. Support (Sales/Marketing) :
TEL:+86-10-62102838
FAX:+86-10-62102848
Wuhan
y
U.S.A.
TEL:+86-27-87851061
FAX:+86-27-87851330
GuangZhou
G.B.T. INC.
TEL:+1-626-854-9338
FAX:+1-626-854-9339
Tech. Support:
TEL:+86-20-87540700
FAX: +86-20-87544306 ext. 333
Chengdu
TEL:+86-28-85236930
FAX: +86-28-85256822 ext. 814
Xian
y
Mexico
G.B.T Inc (USA)
Tel: +1-626-854-9338 x 215 (Soporte de habla hispano)
FAX:+1-626-854-9339
TEL:+86-29-85531943
FAX:+86-29-85539821
Shenyang
Tech. Support:
TEL:+86-24-83992901
FAX:+86-24-83992909
y
India
y
Japan
GIGABYTE TECHNOLOGY (INDIA) LIMITED
NIPPON GIGA-BYTE CORPORATION
y
Australia
y
Singapore
GIGABYTE TECHNOLOGY PTY. LTD.
GIGA-BYTE SINGAPORE PTE. LTD.
- 87 -
Appendix
y
Germany
y
Russia
G.B.T. TECHNOLOGY TRADING GMBH
Moscow Representative Office Of GIGA-BYTE Technology
Co., Ltd.
y
U.K.
G.B.T. TECH. CO., LTD.
y
Latvia
GIGA-BYTE Latvia
y
The Netherlands
GIGA-BYTE TECHNOLOGY B.V.
y
Poland
Office of GIGA-BYTE TECHNOLOGY Co., Ltd. in POLAND
y
France
GIGABYTE TECHNOLOGY FRANCE
y
Ukraine
y Romania
y
Italy
Spain
Representative Office Of GIGA-BYTE Technology Co., Ltd.
in Romania
y
GIGA-BYTE SPAIN
y
Serbia & Montenegro
y
Czech Republic
Representative Office Of GIGA-BYTE Technology Co., Ltd.
in SERBIA & MONTENEGRO
Representative Office Of GIGA-BYTE Technology Co., Ltd.
in CZECH REPUBLIC
y
Turkey
Representative Office Of GIGA-BYTE Technology Co., Ltd.
in TURKEY
y
GIGABYTE Global Service System
To submit a technical or non-technical (Sales/
Marketing) question, please link to :
Then select your language to enter the system.
GA-965P-DS3 Motherboard
- 88 -
|