IBM T540 User Manual

T54A-E.book Page 1 Saturday, February 19, 2000 12:05 PM  
English  
T54A-E.book Page 1 Saturday, February 19, 2000 12:05 PM  
Contents  
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
Hardware Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
Handling Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
Workplace Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
Adjusting the Monitor Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
Working Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
Connecting your Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
Switching on your Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
Configuring your Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Setup Diskette for Windows 95, Windows 98 . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Setup Diskette for Windows 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Auto Setup  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Auto Setup for DOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
Auto Setup for Windows 3.1, Windows 95,  
Windows 98, Windows NT, or Windows 2000 . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Manual Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
Adjusting Your LCD Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
User controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
On-screen display (OSD) controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Further Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Display modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Product Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Further Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
Warranty Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
Appendices (Compliances and Warranty)  
1
T54A-E.book Page 2 Saturday, February 19, 2000 12:05 PM  
Setup  
Hardware Requirements  
This monitor requires a computer with a suitable on-board sub-system or  
Video Adapter card that can support XGA 1024 × 768, SVGA 800 x 600, or  
VGA 640 x 480 at 60 Hz.  
Handling Instructions  
Do not support the monitor  
within the screen area. The  
Liquid Crystal Display is  
glass and can be damaged  
by rough handling or  
1. Lift the monitor by placing your hands where indicated below.  
excessive pressure.  
2. Before using your monitor for the first time, remove the clear protective  
film from the front of the screen.  
Workplace Preparation  
This section gives advice  
Height  
on what you should  
consider before you set up your  
monitor.  
The monitor should be positioned so that the top of the screen is slightly  
below your eye level when you sit at your workstation.  
Orientation  
Choose a position that gives the least reflection from lights and windows,  
usually at a right angle to any windows. The monitor should be positioned  
directly in front of you so that you do not have to twist your body to use it. Tilt  
the monitor to a comfortable viewing angle.  
2
T54A-E.book Page 3 Saturday, February 19, 2000 12:05 PM  
Adjusting the Monitor Position  
Viewing Angle  
You can tilt the screen backward and forward as shown below.  
Working Practices  
This section gives  
advice on how you can  
work comfortably and reduce  
fatigue.  
Rest  
Take regular breaks. Vary your posture, stand up and stretch occasionally as  
prolonged use of computer workstations can be tiring.  
Back  
You should sit back in your chair and use the backrest.  
Hands  
Adjust the seat height so that your forearms are approximately horizontal and  
your wrists are straight when using the keyboard. Your upper arms should be  
relaxed with your elbows near your body.  
Use a light touch on the keyboard, keeping your hands and fingers relaxed.  
Allow a space in front of the keyboard to rest your wrists when not typing.  
Consider using a wristpad.  
3
T54A-E.book Page 4 Saturday, February 19, 2000 12:05 PM  
Eyesight  
Working with monitors, in common with any prolonged close work, can be  
visually demanding. Look away from the screen periodically and have your  
eyesight checked regularly.  
Screen settings  
Set the screen brightness and contrast to a comfortable level. You may have  
to adjust this as the lighting changes during the day. Many application  
programs let you select color combinations which can help you to view in  
comfort. See the User controls section on page 13 for more information.  
4
T54A-E.book Page 5 Saturday, February 19, 2000 12:05 PM  
Connecting your Monitor  
Be sure to read the Safety  
Informationat the front of  
this User Guide before  
1. Turn off your PC and all attached devices.  
2. Connect the signal cable to the video port on the back of your computer.  
This port might be directly attached to your computer (figure A), or it  
might be part of a video adapter card (figure B). The video port on your  
computer or video adapter card may be colored blue to match the blue  
connector on your monitors video cable.  
carrying out this procedure.  
The AC adapter and signal  
cable are connected to  
your monitor. If you wish to  
change these or to fit a different  
stand, see Further Help on  
page 22.  
3. Connect the power cord to the power adapter first, then insert the plug  
into a properly grounded electrical outlet.  
Switching on your Monitor  
1. Switch on the power source and your computer.  
2. Switch on your monitor by pushing and releasing the power switch  
marked  
.
To switch off your monitor, push and release the power switch again.  
3. Turn on the monitor and then the computer.  
4. Run AUTO SETUP by following the instructions in the Configuring your  
Monitor section on page 6.  
5
T54A-E.book Page 6 Saturday, February 19, 2000 12:05 PM  
Configuring your Monitor  
Setup Diskette for Windows95 or Windows 98  
This section must be  
completed before  
continuing with the  
Windows 95 or Windows 98  
Auto Setup on Page 10.  
To use the Plug and Play feature in Windows 95 or Windows 98, files should  
be loaded from the IBM Flat Panel Monitor Installation diskette:  
1. Turn off the computer and all attached devices.  
2. Ensure that the monitor is connected correctly.  
3. Turn on the monitor and then the system unit. Allow the system to boot  
into Windows 95 or Windows 98.  
Your computers Plug and Play code may warn you that your system  
hardware has changed. This probably means that it has detected your  
new monitor for the first time.  
4.  
5.  
Open the DISPLAY PROPERTIES window by clicking on START, SETTINGS,  
CONTROL PANEL and then double clicking on the DISPLAY icon.  
Select the SETTINGS tab.  
On LCD monitors,  
unlike CRTs, a faster  
refresh rate does not  
improve display quality.  
IBM recommends using  
1024 x 768 at a refresh  
rate of 60Hz.  
In case of Windows 95:  
6. -1. Select the Change Display Type button.  
2. Select the Change Monitor Type button.  
In case of Windows 98:  
6. -1. Select the ADVANCED BUTTON.  
2. Select the MONITOR tab.  
3. Open the UPGRADE DEVICE WIZARD windows by clicking on  
Change button and then select the NEXT button.  
If the UPGRADE DEVICE WIZARD is open go step 6-3. if not  
continue to step 4.  
4. Select the Display a list of the known drivers for this device so that  
I can choose a specific driverand then select the NEXT button.  
7. Insert the Setup diskette into drive A: and select the HAVE DISK button.  
8. Select OK.  
9. Choose IBM T540 monitor and select OK. The files will be copied from  
the diskette to your hard drive.  
10. Close all open windows and remove the diskette.  
11. Reboot the system.  
The system will automatically select the maximum refresh rate and  
corresponding Color Matching Profiles.  
6
T54A-E.book Page 7 Saturday, February 19, 2000 12:05 PM  
Setup Diskette for Windows 2000  
This section must be  
completed before  
continuing with the  
Windows 2000 confguring  
for your monitor on page 10.  
To use the Plug and Play feature in Windows 2000, files should be loaded  
from the IBM Flat Panel Monitor Installation diskette.  
1. Turn off the computer and all attached devices.  
2. Ensure that the monitor is connected correctly.  
3. Turn on the monitor and then the system unit. Allow the system to boot  
into Windows 2000.  
4.  
Open the DISPLAY PROPERTIES window by clicking on START, SETTINGS,  
CONTROL PANEL and then double clicking on the DISPLAY icon.  
5.  
Select the SETTINGS tab.  
6. Select the ADVANCED button.  
On LCD monitors, unlike  
CRTs, a faster refresh rate  
does not improve display  
quality. IBM recommends using  
1024 x 768 at a refresh  
rate of 60Hz.  
7.  
8.  
Select the MONITOR tab.  
Select the PROPERTIFS button.  
9. Select the Driver tab.  
10. Open theUpgrade Device Driver Wizard window by clicking on UPDATE  
DRIVER and then select the NEXT button.  
11. select the Display a list of the known dirvers for this device so that lcan  
choose a specifc driverand then sefect the NEXT button.  
12. Inset the Setup diskette into drive A: and select the HAVE DISK button.  
13. select OK.  
14. Choose IBM T540 monitor and select OK. The files will be copied from  
the diskette to your hard drive.  
15. Close all open windows and remove the diskette.  
16. Reboot the system.  
The system will automatically select the maximum refresh rate and  
corresponding Color Matching Profiles.  
7
T54A-E.book Page 8 Saturday, February 19, 2000 12:05 PM  
Auto Setup  
Auto Setup  
Before carrying out this  
section, it is very  
important that The Setup  
Diskette for Windows 95 or  
Windows 98 has been run.  
(see page 6)  
When you first use your monitor you must perform Auto Setup. This  
procedure sets up your monitor to process the video signals from your  
computer without image discoloration or smearing. After you perform Auto  
Setup, the settings are stored and used each time you turn on the monitor.  
In order to optimise the displayed image a set-up utility is provided on the IBM  
Monitor Installation Diskette. Operation of the utility is dependent on the  
operating system on your PC. For correct operation locate the operating  
system on your PC from the table below and follow the appropriate  
instructions. You may choose to run AUTO SETUP for each operating system  
that you use. This means that if you sometimes use your monitor while  
running any version of Windows and sometimes also use it from within DOS  
(not a DOS window), you must run AUTO SETUP for both Windows and DOS.  
You may run versions of AUTO SETUP in any order.  
The Setup Utility  
included on the setup  
diskette is for displaying do  
patterns. They do not replace  
or modify the display dirver.  
The Auto Setup instructions  
require the monitor to be  
warmed up for 15 minutes.  
This is not required for normal  
operation.  
Operating System  
DOS  
Corresponding Auto Setup procedure  
Auto Setup for DOS on page 9  
By pressing the  
Åꢀand Æ keys  
simultaneously allows  
direct access to the auto set-  
up controls.  
Windows 3.1  
Windows 95  
Windows 98  
Window 2000  
Window NT  
Auto Setup for Windows 3.1, Windows 95,  
Windows 98, Windows 2000 or Windows  
NT on page 10  
If your PC does not run  
with the setup diskettes  
Before you begin AUTO SETUP for your PC:  
shipped with the monitor, refer  
to Manual Setup on page 12  
1. Make a backup copy of the setup diskettes supplied with the monitor.  
2. Make sure the PCs video mode is set in the range of the supported  
screen resolution shown in the table on page 18.  
The AUTO SETUP process  
only applies to the current  
screen mode. When a new  
mode is selected, repeat this  
section to reset the monitor  
You should perform AUTO SETUP for each screen mode you use.  
8
T54A-E.book Page 9 Saturday, February 19, 2000 12:05 PM  
Auto Setup for DOS  
If the monitor is in standby  
1. Turn on the monitor first; then the PC.  
mode (STANDBY ON), it  
may automatically turn off while  
you are waiting for it to warm up.  
If this happens, switch off the  
monitor and switch it on again  
after a few seconds.  
If the message CHECK SIGNAL CABLE is displayed, or if nothing is  
displayed check:  
that the video interface cable is connected properly.  
the correct video adapter card is installed.  
the correct supported display mode is selected for your PC.  
If you are using PC-DOS/  
V, change to U.S. mode by  
typing CHEV USand pressing  
ENTER at the command  
prompt.  
2. Wait approximately 15 minutes, until the monitor warms up.  
3. Insert the diskette labelled IBM Flat Panel Monitor Installation Diskette  
into the diskette drive.  
You must use DOS when  
you run DOS Auto Setup.  
4. Display the command prompt screen of the DOS full-screen display.  
5. At the command prompt, type A:and press ENTER.  
6. Type TESTPATDand press ENTER.  
7. Select from the screen the number for the color or text mode you want to  
setup.  
8. Select from the screen the number for the video mode you want to  
setup.  
You may repeat this process for as many of the color and video modes  
as you need.  
The size and diversity of  
the dot pattern varies with  
the screen resolution.  
9. When the dot pattern appears, press the OSD Enter button  
bottom of the monitor to display the initial OSD menu.  
at the  
If the screen flickers,  
10. Use an Arrow button (  
then press the OSD Enter  
or  
) to select the IMAGE LOCK icon  
button to access the function.  
repeat the setup several  
times until the flicker is  
minimised, or adjust it manually  
by following Manual Setup on  
page 12.  
11. Using an Arrow button (  
or  
), select AUTOMATIC and press the  
OSD Enter button  
. This activates the AUTO SETUP procedure, which  
will optimize the display settings with the provided dot-patterns.  
The screen will3d off several times and you may notice small changes to  
the test pattern.  
12. When finished, the OSD main menu returns. Press the Exit button  
to exit from the OSD.  
13. Press the ESCAPE key to exit the test pattern program.  
14. Type Exitat the command prompt to return to Windows.  
If you use other operating systems, perform the appropriate AUTO SETUP for  
those systems, also: see  
Auto Setup for Windows 3.1, Windows 95, Windows 98, Windows NT or  
Windows 2000 on page 10.  
9
T54A-E.book Page 10 Saturday, February 19, 2000 12:05 PM  
Auto Setup for Windows 3.1, Windows 95, Windows 98, Windows NT  
or Windows 2000  
If the monitor is in standby  
mode (STANDBY ON), it  
1. Turn on the monitor first; then the PC.  
may automatically turn off while  
you are waiting for it to warm up.  
If the message CHECK SIGNAL CABLE is displayed, or if nothing is  
displayed check:  
that the video interface cable is connected properly.  
the correct video adapter card is installed.  
the correct supported display mode is selected for your PC.  
2. Wait approximately 15 minutes, until the monitor warms up.  
3. Drag the icon bar and tool bar, if they are displayed, to the bottom of the  
screen.  
4. Insert the diskette labelled IBM Flat Panel Monitor Installation Diskinto  
the diskette drive.  
The size and diversity of  
the dot pattern varies with  
the screen resolution.  
5. Check the operating system installed on your PC and follow the  
instructions from the table below.  
Operating  
System  
Step1  
Step2  
Step3  
Step4  
Windows 3.1  
Open  
PROGRAM  
MANGER  
Select  
FILE  
Select  
RUN  
Windows NT 3.5  
Type  
A:\TESTPAT’  
and press  
ENTER  
Windows 95  
Select  
START  
Windows 98  
Select RUN  
Windows NT 4.0  
6. When the test pattern appears, press the OSD Enter button  
bottom of the monitor to display the initial OSD menu.  
at the  
Position the mouse pointer  
at the bottom center of the  
screen. This allows AUTO  
SETUP to run properly  
7. Use an Arrow button (  
and press the OSD Enter button  
8. Using an Arrow button ( or  
OSD Enter button . This activates the AUTO SETUP procedure, which  
or  
) to select the IMAGE LOCK icon  
to access the function.  
), select AUTOMATIC and press the  
will optimize the display settings with the provided test pattern.  
The screen will dim, blink on and off several times, and you may notice  
small changes to the test pattern.  
To abort the AUTO SETUP function, press the ESC key.  
9. When finished, the OSD main menu returns. Press the Exit button  
once to exit from the OSD.  
10. Press the ESC key to return to Windows.  
10  
T54A-E.book Page 11 Saturday, February 19, 2000 12:05 PM  
You have completed the monitor setup for Windows. If you use other operat-  
ing systems, perform the appropriate AUTO SETUP for those systems, also: see  
Auto Setup for DOS on page 9.  
11  
T54A-E.book Page 12 Saturday, February 19, 2000 12:05 PM  
Manual Setup  
Normally, you can complete the setup procedure using AUTO SETUP, however,  
if your screen image is still distorted after you perform AUTO SETUP or the  
setup diskette does not run on your system, perform MANUAL SETUP.  
If the monitor is in standby  
mode (STANDBY ON), it  
might automatically turn off  
while you are waiting for it to  
warm up.  
1. Have your monitor turned on for about 15 minutes, until the monitor  
warms up.  
2. Display the image you most frequently use on the screen.  
3. Press the OSD Enter button  
the initial OSD menu.  
at the bottom of the monitor to display  
4. Use an Arrow button (  
and press the OSD Enter button  
5. Using an Arrow button ( or  
press once to select COARSE. Left and right arrow adjustment  
or  
) to select the IMAGE LOCK icon  
to access the function.  
), select MANUAL, press  
and then  
indicators become illuminated (see page 16).  
6. Use the Arrow buttons to manually adjust to correct (as much as  
possible) for noise in the video signal then press  
changes.  
to save the  
7. Use an Arrow button to select FINE and press the  
button.  
8. Use the Arrow buttons again to tune the image to your liking.  
9. When finished, press the Exit button  
OSD.  
four times to exit from the  
You have completed the monitor setup.  
12  
T54A-E.book Page 13 Saturday, February 19, 2000 12:05 PM  
Adjusting Your LCD Monitor  
User controls  
User control features  
Icon  
Control  
Exit  
Description  
Displays the OSD main menu  
Exits from menus and sub-menus  
Exits the OSD  
Displays the OSD main menu  
Moves the cursor to highlight icons and other  
options  
Left Arrow  
Displays the OSD main menu  
Moves the cursor to highlight icons and other  
options  
Right Arrow  
Displays the OSD main menu  
Enters menus and sub-menus and selects the  
highlighted option  
OSD Enter  
Power Switch  
Switches the monitor on and off  
Operation  
The image is already  
optimized for many display  
modes, however the user  
controls can be used to adjust  
the image to your liking.  
Press any of the OSD control buttons to display the main OSD menu.  
Use the Arrow buttons to move among the icons. Select an icon and press  
OSD Enter to access that function. If there is a sub-menu, you can move  
between options using the Arrow buttons, then press OSD Enter to select  
that function. Use the Arrow buttons to make adjustments.  
13  
T54A-E.book Page 14 Saturday, February 19, 2000 12:05 PM  
The settings are saved  
Press the Exit button to move backwards through the sub-menus and exit  
from the OSD.  
after adjustment and when  
exiting the OSD and will be  
effective thereafter.  
Note: After making adjustments, the Power indicator LED will briefly  
turn amber to indicate that the new value has been saved.  
OSD Lock / Unlock  
This feature allows you to secure the current control settings, while allowing  
the user to adjust Brightness and Contrast, so that they cannot be  
inadvertently changed. You can unlock the OSD controls at any time by using  
the same procedure.  
Push and hold the OSD Enter button for 10 seconds to Lock or to Unlock.  
When locked, a LOCKEDmessage will be displayed.  
14  
T54A-E.book Page 15 Saturday, February 19, 2000 12:05 PM  
On-screen display (OSD) controls  
The settings adjustable with the user controls are viewed through the On-  
Screen Display (OSD). Press any of the OSD buttons to activate the OSD.  
The LCD monitor needs  
time to become thermally  
Initial appearance of OSD  
stable the first time you turn it on  
each day. Thus, to achieve more  
accurate adjustments for  
parameters, allow the LCD  
monitor to warm up (be On) for  
at least 15 minutes before  
making any screen adjustments.  
OSD functions  
Controls and  
Adjustments  
OSD Icon  
Description  
Sub-menu(s)  
Adjusts brightness  
BRIGHTNESS  
CONTRAST  
Adjusts contrast  
The image lock function is used to  
adjust the level of noise in the video  
signal which causes horizontal lines or  
areas on the screen where the image  
appears to be unstable and jitters or  
shimmers. This can be done  
Automatic adjustment  
Automatic  
IMAGE LOCK  
automatically or manually.  
15  
T54A-E.book Page 16 Saturday, February 19, 2000 12:05 PM  
Controls and  
Adjustments  
OSD Icon  
Description  
Sub-menu(s)  
Manual -  
Use the Arrow buttons to  
adjust away the  
interference. If  
Fine  
Coarse  
IMAGE LOCK  
(continued)  
satisfactory results are  
not obtained using the  
Fine adjustment, use the  
Coarse adjustment and  
then use Fine again.  
This function may  
change the width of the  
display image. Use the  
H-Position function on  
the Image Position  
menu to center the  
display image on the  
screen.  
Moves the screen left and right or up  
and down.  
H-Position  
V-Position  
Color Mode  
IMAGE  
POSITION  
Select the Color Mode you find most  
comfortable and then fine tune the  
colors using the User Color Mode  
menu, if necessary.  
Mode 1  
(Cool White)  
COLOR  
Mode 2  
(Normal White)  
Mode 3  
(Warm White)  
User Mode -  
Red  
Increases or decreases  
redness  
Green  
Blue  
Increases or decreases  
greenness  
Increases or decreases  
blueness  
16  
T54A-E.book Page 17 Saturday, February 19, 2000 12:05 PM  
Controls and  
Adjustments  
OSD Icon  
RESET  
Description  
Sub-menu(s)  
Color Reset  
Resets the Brightness, Contrast and  
Color settings.  
NO - Does not make the  
adjustment  
YES - Resets the color  
Resets the Image position settings  
Geometry  
Reset  
NO - Does not make the  
adjustment  
YES - Resets the  
geometry  
Shows information about the  
addressability and the horizontal and  
vertical frequencies of the images  
received from the computer or video  
board.  
INFORMATION  
LANGUAGE  
The language chosen affects only the  
language of the OSD. It has no effect  
on any software running on the  
computer.  
Select one of the five  
languages to use for the  
OSD.  
Changes the position of the OSD on  
the screen.  
H-Position  
V-Position  
OSD MENU  
POSITION  
17  
T54A-E.book Page 18 Saturday, February 19, 2000 12:05 PM  
Further Information  
Display modes  
The display mode the monitor uses is controlled by the computer. Therefore,  
you should refer to your computer documentation for details on how to  
change display modes.  
The image size, position and shape may change when the display mode  
changes. This is normal and the image can be readjusted using AUTO SETUP  
and the monitor controls.  
Unlike CRT monitors, which require a high refresh rate to minimize flicker,  
TFT technology is inherently flicker-free. If possible, configure your computer  
for 1024 × 768 addressability at 60Hz vertical refresh rate.  
For the display modes listed below, the screen image has been optimized  
during manufacture.  
Factory Set Display Modes  
Addressability  
Refresh Rate  
Horizontal Frequency  
640 × 350  
640 × 480  
640 × 480  
640 × 480  
720 × 400  
800 × 600  
800 × 600  
800 × 600  
800 × 600  
832 × 624  
1024 × 768†  
1024 × 768  
1024 × 768  
70 Hz  
60 Hz  
72 Hz  
75 Hz  
70 Hz  
75 Hz  
72 Hz  
60 Hz  
56 Hz  
75 Hz  
60 Hz  
70 Hz  
75 Hz  
31.5 kHz  
31.5 kHz  
37.9 kHz  
37.5 kHz  
31.5 kHz  
46.9 kHz  
48.1 kHz  
37.9 kHz  
35.2 kHz  
49.7 kHz  
48.4 kHz  
56.5 kHz  
60.0 kHz  
Recommended  
Note: VESA timings are as detailed in the VESA Display Monitor Timing  
Specification. Version 1.0, Revision 0.8, dated 09/17/98.’  
18  
T54A-E.book Page 19 Saturday, February 19, 2000 12:05 PM  
Power Management  
If your computer has  
previously been used  
To benefit from power management, the monitor must be used in conjunction  
with a computer that implements the Video Electronics Standards Association  
(VESA) Display Power Management Signalling (DPMS) Standard.  
with a CRT monitor and is  
currently configured to a  
display mode outside the  
range that the Flat Panel  
monitor can display, you  
may need to re-attach the  
CRT monitor temporarily  
until you have re-configured  
the computer, preferably to  
1024 x 768 at 60Hz.  
The power management feature is invoked when the computer recognizes  
that you have not used your mouse or keyboard for a user-definable period.  
There are several states as described in the table below.  
As an ENERGY STAR® Partner, IBM has determined that this product meets the  
ENERGY STAR® guidelines for energy efficiency.  
IBM recommends that you switch off your monitor at the end of each working  
day, or whenever you expect to leave it unused for long periods during the  
day.  
Power  
Indicator  
Restoring  
Operation  
State  
Screen  
Normal  
Blank  
Compliance  
On  
Steady green  
Steady amber  
®
DPMS  
Standby  
Press a key or  
move the mouse.  
ENERGY STAR  
and NUTEK  
Flashing  
amber  
(0.5 sec.  
interval)  
®
DPMS  
Suspend  
Press a key or  
move the mouse. ‡  
ENERGY STAR  
and NUTEK  
Blank  
Blank  
Flashing  
amber  
(1 sec.  
interval)  
®
Press a key or  
move the mouse. ‡  
ENERGY STAR  
and NUTEK  
DPMS Off  
There may be a slight delay before the picture reappears.  
Product Disposal  
The fluorescent lamp in the liquid crystal display contains mercury. Dispose of  
it as required by local ordinances and regulations.  
19  
T54A-E.book Page 20 Saturday, February 19, 2000 12:05 PM  
Troubleshooting  
If you have a problem setting up or using your monitor, you may be able to  
solve it yourself. Before calling your retailer or IBM, try the suggested actions  
that are appropriate to your problem.  
Possible  
Cause  
Problem  
Suggested Action  
Reference  
ŠꢀEnsure that the  
electrical outlet and the  
monitor are both switched  
on.  
ŠꢀCheck that the power  
cord is firmly plugged into  
the electrical outlet and the  
power supply unit.  
Connecting  
your Monitor  
section on  
Screen is blank  
and power  
indicator is off  
No power to  
monitor  
ŠꢀIf the power cord plug  
has a removable fuse,  
replace it.  
page 5  
ŠꢀTry another power  
cord.  
ŠꢀTry another electrical  
outlet.  
User  
Screen is blank  
and power  
indicator is  
Brightness  
and Contrast  
may be too  
low  
ŠꢀAdjust brightness and  
contrast.  
controls  
section on  
page 13  
steady green  
ŠꢀPress any key on the  
keyboard or move the  
mouse to restore  
Power  
Screen is blank  
and power  
indicator is  
The monitor is  
in the Power  
Management  
Standby state  
Management  
section on  
page 19  
operation.  
ŠꢀCheck the Power  
Management software on  
your computer  
steady amber  
20  
T54A-E.book Page 21 Saturday, February 19, 2000 12:05 PM  
Possible  
Cause  
Problem  
Suggested Action  
Reference  
ŠꢀCheck that the signal  
cable is firmly connected to  
the computer.  
Connecting  
your Monitor  
section on  
The monitor is  
not receiving  
a video signal  
ŠCheck that no pins are  
bent in the signal cable  
connector.  
Screen is blank  
and power  
indicator is  
Flashing green  
every 0.5  
page 5  
Display mode  
of the  
computer is  
outside the  
range of the  
monitor  
Further  
second  
ŠꢀReconfigure the  
computer to use a  
supported display mode.  
Information  
section on  
page 18  
ŠꢀPress any key on the  
keyboard or move the  
mouse to restore  
Screen is blank  
and power  
indicator is  
flashing amber  
every 0.5 or 1  
second  
The monitor is  
in the Power  
Management  
Suspend or  
Off state  
Power  
Management  
section on  
page 19  
operation.  
ŠꢀCheck the Power  
Management software on  
your computer.  
User  
ŠꢀSelect IMAGE LOCK  
menu in the OSD. Then  
select MANUAL to adjust  
FINE/COARSE settings.  
For image problems, you  
may want to run AUTO  
There are  
noises in the  
video signal  
Image appears  
to be smeared  
controls  
section on  
page 13  
Setup again before consulting  
to this section. In most cases,  
AUTO SETUP can fix the  
problems. See Auto Setup on  
page 8 for details.  
User  
Image appears  
to be  
discolored  
The Color  
setting may  
be incorrect  
ŠꢀAdjust the Color  
settings.  
controls  
section on  
page 13  
ŠꢀThe LCD contains over 2,300,000 thin-  
film transistors (TFTs). A small number of  
missing, discolored, or lighted dots may be  
present on the screen, which is an intrinsic  
characteristic of the TFT LCD technology  
and is not an LCD defect.  
A few dots are  
missing,  
discolored, or  
inappropriately  
lighted.  
21  
T54A-E.book Page 22 Saturday, February 19, 2000 12:05 PM  
Further Help  
If you are unable to correct the problem yourself, you may seek further help  
as follows:  
Call the IBM HELPCENTER.  
In the US call 1-800-772-2227  
In Canada call 1-800-565-3344  
In other countries contact your dealer, retailer, or other IBM authorized  
Servicer.  
If possible, stay by your  
computer. Your Technical  
Support Representative may  
wish to go through the problem  
with you during the call.  
Before calling, please have available as much of the following information as  
possible:  
1. Model and serial number from the label on your monitor.  
2. Purchase receipt.  
3. Description of problem.  
4. Computer type and model.  
5. System configuration (hardware fitted, etc.).  
6. System BIOS version number.  
7. Operating System and version number.  
8. Display driver version number.  
9. Video Adapter Type.  
More help, late-breaking  
news and details of the  
Removing the stand and cables  
Alternative stands for your IBM Flat Panel Monitor may be available from  
specialist suppliers.  
latest accessories for these  
products may be found on the  
worldwide web at:  
This product is equipped with mounting facilities that conform to the VESA  
Flat Panel Monitor Physical Mounting Interface Standard (FPMPMI).  
accessories  
This product is shipped with the signal cable and the power cord attached to  
the monitor. If you want to use other cables for reasons such as having the  
monitor wall-mounted, follow the instructions below:  
Information about the Video  
Electronics Standards  
Association can be found on the  
worldwide web at:  
1. Disconnect the power cord from the wall outlet.  
22  
T54A-E.book Page 23 Saturday, February 19, 2000 12:05 PM  
2. Carefully insert the head of a flathead () screwdriver into the slot visible  
along either side of the cable cover (a) and pry it off.  
a
b
c
3. Squeeze the sides of the hinge cover (b) and pull it off.  
4. Gently lift the stand cover (c) along the top and then slide it backwards  
and off the stand.  
5. Remove the signal cable and the power cord from the monitor by  
disconnecting the corresponding adapters. Carefully cut the plastic tie to  
free the power cord and remove the screw holding the power cord  
clamp.  
6. Lay the monitor facedown on a cushion and remove the six screws  
holding the hinge mechanism on the monitor. Lift off the hinge and base  
assembly.  
7. If you are installing an arm or wall-mounting device, follow the directions  
included with the device. If you are just changing your cables, continue  
with Step 8.  
8. Connect the signal cable and the power cord, then refit the power cord  
clamp in its original screwpost.  
9. Slide the stand cover back on the stand.  
10. Put the hinge cover back on, making sure that the straight side is at the  
top.  
11. Insert the three tabs at the top of the cable cover into the slots in the  
back of the monitor and push the cover into place.  
To obtain the correct cables and/or to get further instructions on installing  
them, call the IBM HELPCENTER at the above numbers or contact your  
dealer, retailer, or other IBM authorized Servicer.  
23  
T54A-E.book Page 24 Saturday, February 19, 2000 12:05 PM  
Specifications  
This color monitor (Type-model 9511-Axx) uses a 15-inch TFT LCD  
Dimensions  
Width:  
Depth:  
Height:  
401 mm  
202 mm  
371 mm  
Weight  
Tilt  
Unpackaged:  
packaged:  
11.2 lb. (5.1 Kg)  
13.9 lb. (6.3 Kg)  
Forward Tilt:  
Backward tilt:  
4°  
+ 41°  
Image  
Viewable Image Size:  
Maximum Height:  
Maximum Width:  
Pixel Pitch:  
15.0(381 mm)  
228.1 mm  
304.1 mm  
0.297 mm (H) × 0.297 mm (V)  
Power Input  
Supply Voltage:  
90 - 260 Vac  
60/50 3 Hz  
1.0 A at 120 Vac  
Max Supply Current:  
Power consumption  
figures are for the monitor  
and the power supply  
combined.  
Power Consumption  
Normal Operation:  
DPMS Stand-by:  
DPMS Suspend:  
DPMS off:  
< 30 W  
<
<
<
3 W  
3 W  
3 W  
Video Input  
Input Signal:  
Analog Direct Drive  
75 ohm 0.7 V  
Horiz. Addressability:  
Vert. Addressability:  
Clock Frequency:  
1024 pixels (max)  
768 lines (max)  
80 MHz  
Communications  
VESA DDC:  
2 B  
Supported Display  
Modes  
VESA Standard 12 modes  
See page 18  
Macintosh 1 mode  
Environment  
Temperature:  
Operating:  
Storage:  
10 to 35° C  
- 20 to 60° C  
- 20 to 60° C  
Shipping:  
Humidity:  
Operating:  
Storage:  
10 to 80%  
5 to 95%  
5 to 95%  
Shipping:  
24  
T54A-E.book Page 25 Saturday, February 19, 2000 12:05 PM  
Warranty Statements  
Your Installation Diskette includes translation of IBMs Statement of  
Warranty in following languages:  
Worldwide Statement of Warranty  
(Except Turkiye, U.S., Puerto Rico and Canada):  
Z1255697.ara.html  
Arabic  
Z1255697.bra.html  
Z1255697.bul.html  
Z1255697.chi.html  
Z1255697.cro.html  
Z1255697.cze.html  
Z1255697.dan.html  
Z1255697.dut.html  
Z1255697.eng.html  
Z1255697.fin.html  
Z1255697.fre.html  
Z1255697.ger.html  
Z1255697.gre.html  
Z1255697.heb.html  
Z1255697.hun.html  
Z1255697.ita.html  
Z1255697.jap.html  
Z1255697.kor.html  
Z1255697.nor.html  
Z1255697.pol.html  
Z1255697.por.html  
Z1255697.rus.html  
Z1255697.sla.html  
Z1255697.sle.html  
Brazilian portuguese  
Bulgarian  
Chinese  
Croatian  
Czech  
Danish  
Dutch  
English  
Finnish  
French  
German  
Greek  
Hebrew  
Hungarian  
Italian  
Japanese  
Korean  
Norwegian  
Polish  
Portuguese  
Russian  
Slovakian  
Slovenian  
25  
T54A-E.book Page 26 Saturday, February 19, 2000 12:05 PM  
Z1255697.spa.html  
Z1255697.swe.html  
Z1255697.tai.html  
Spanish  
Swedish  
Taiwanese  
Turkiye Statement of Warranty:  
Z1255698.tur.html  
Z1255698.eng.html  
Turkish  
English  
United States, Puerto Rico and Candada Statement of Limited Warranty:  
Z1254753.eng.html  
Z1254753.fca.html  
English  
French Canadian  
26  

Iiyama PROLITE E2003WSV User Manual
Intel D845HV User Manual
Jenn Air GAS COOKTOPS User Manual
Melissa Cooker Hood with Glass Plate 258 014 User Manual
Miele KM5945 User Manual
MSi MSI ATX Motherboard G52 MA00362 User Manual
Mustek LM 3000 User Manual
Philips Aleor TD 9220 User Manual
Philips Cooktop HD4928 User Manual
Philips SBC SC280 User Manual