HP Hewlett Packard x23LED User Manual

HP x20LED, x22LED, x22LEDc and x23LED Monitors  
User Guide  
© 2010 Hewlett-Packard Development Company, L.P.  
Microsoft, Windows, and Windows Vista are either  
trademarks or registered trademarks of Microsoft  
Corporation in the United States and/or other countries.  
The only warranties for HP products and services are set  
forth in the express warranty statements accompanying  
such products and services. Nothing herein should be  
construed as constituting an additional warranty. HP shall  
not be liable for technical or editorial errors or omissions  
contained herein.  
This document contains proprietary information that is  
protected by copyright. No part of this document may be  
photocopied, reproduced, or translated to another  
language without the prior written consent of Hewlett-  
Packard Company.  
Document Part Number: 603461-002  
Second Edition, (June 2010)  
About This Guide  
This guide provides information on setting up the monitor, installing drivers, using the  
on-screen display menu, troubleshooting and technical specifications.  
WARNING! Text set off in this manner indicates that failure to follow directions  
could result in bodily harm or loss of life.  
CAUTION: Text set off in this manner indicates that failure to follow directions  
could result in damage to equipment or loss of information.  
NOTE: Text set off in this manner provides important supplemental information.  
ii  
 
Table of Contents  
ENWW  
iii  
German Ergonomics Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
Japanese Power Cord Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
Disposal of Waste Equipment by Users in  
iv  
1. Product Features  
HP LCD Monitors  
The HP LCD (liquid crystal display) monitors have an active matrix, thin-film transistor  
(TFT) screen with the following features:  
Large diagonal display  
Maximum graphics resolution:  
x20LED: 1600 x 900 @ 60Hz  
x22LED/x22LEDc: 1920 x1080 @ 60Hz  
x23LED: 1920 x 1080 @ 60Hz  
Plus full-screen support for lower resolutions  
VGA analog signal  
DVI digital signal  
Easy viewing from a sitting or standing position, or while moving from one side of  
the monitor to the other  
Tilt adjustment  
Removable base  
Security lock slot for a locking security cable (security cable sold separately)  
Plug and Play capability, if supported by your computer system  
On-screen display (OSD) adjustments for ease of setup and screen optimization  
(choose English, Spanish, French, Portuguese, Russian, Simplified Chinese,  
Traditional Chinese, Korean)  
Power Saver to reduce energy consumption  
Energy-efficient white LED backlight using less power than standard LCD  
monitors  
HDCP (High Bandwidth Digital Content Protection) on DVI input  
Software and utilities CD, containing the following:  
Drivers  
Documents  
ENWW  
HP LCD Monitors  
1
   
2. Safety and Maintenance Guidelines  
Important Safety Information  
A power cord is included with the monitor. If another cord is used, use only a power  
source and connection appropriate for this monitor. For information on the correct  
power cord set to use with the monitor, refer to the "Connecting the Power Cable" section  
on Chapter 3 .  
WARNING! To reduce the risk of electric shock or damage to the equipment:  
Do not disable the power cord grounding feature. The grounding plug is an  
important safety feature.  
Plug the power cord in a grounded (earthed) outlet that is easily accessible at all  
times.  
Disconnect power from the product by unplugging the power cord from the  
electrical outlet.  
For your safety, do not place anything on power cords or cables. Arrange them so that  
no one may accidentally step on or trip over them. Do not pull on a cord or cable.  
When unplugging from the electrical outlet, grasp the cord by the plug.  
To reduce the risk of serious injury, read the Safety and Comfort Guide . It describes  
proper workstation, setup, posture, and health and work habits for computer users,  
and provides important electrical and mechanical safety information. This guide is  
located on the Web at http://www.hp.com/ergo and/or on the documentation CD, if  
one is included with the monitor.  
CAUTION: For the protection of the monitor, as well as the computer, connect all  
power cords for the computer and its peripheral devices (such as a monitor, printer,  
scanner) to some form of surge protection device such as a power strip or  
Uninterruptible Power Supply (UPS). Not all power strips provide surge protection; the  
power strips must be specifically labeled as having this ability. Use a power strip  
whose manufacturer offers a Damage Replacement Policy so you can replace the  
equipment, if surge protection fails.  
Use the appropriate and correctly sized furniture designed to properly support your  
HP LCD monitor.  
WARNING: LCD monitors that are inappropriately situated on dressers, book  
cases, shelves, desks, speakers, chests, or carts may fall over and cause personal  
injury. Care should be taken to route all cords and cables connected to the LCD  
monitor so that they can not be pulled, grabbed, or tripped over.  
Safety Precautions  
Use only a power source and connection compatible with this monitor, as  
indicated on the label/back plate of the monitor.  
Be sure the total ampere rating of the products connected to the outlet does not  
exceed the current rating of the electrical outlet, and the total ampere rating of the  
products connected to the power cord does not exceed the rating of the power  
cord. Look on the power label to determine the ampere rating (Amps or A) for  
each device.  
2
Chapter 2. Safety and Maintenance Guidelines  
ENWW  
     
Install your monitor near a power outlet that you can easily reach. Disconnect the  
monitor by grasping the plug firmly and pulling it from the outlet. Never disconnect  
the monitor by pulling the cord.  
Do not allow anything to rest on the power cord. Do not walk on the cord  
Maintenance Guidelines  
To enhance the performance and extend the life of the monitor:  
Do not open the monitor cabinet or attempt to service this product yourself. Adjust  
only those controls that are covered in the operating instructions. If the monitor is  
not operating properly or has been dropped or damaged, contact an authorized  
HP dealer, reseller, or service provider.  
Use only a power source and connection appropriate for this monitor, as indicated  
on the label/back plate of the monitor.  
Be sure the total ampere rating of the products connected to the outlet does not  
exceed the current rating of the electrical outlet, and the total ampere rating of the  
products connected to the cord does not exceed the rating of the cord. Look on  
the power label to determine the ampere rating (AMPS or A) for each device.  
Install the monitor near an outlet that you can easily reach. Disconnect the  
monitor by grasping the plug firmly and pulling it from the outlet. Never disconnect  
the monitor by pulling the cord.  
Turn the monitor off when not in use. You can substantially increase the life  
expectancy of the monitor by using a screen saver program and turning off the  
monitor when not in use  
Slots and openings in the cabinet are provided for ventilation. These openings  
must not be blocked or covered. Never push objec ts of any kind into cabinet slots  
or other openings.  
Do not drop the monitor or place it on an unstable surface.  
Do not allow anything to rest on the power cord. Do not walk on the cord.  
Keep the monitor in a well-ventilated area, away from excessive light, heat or  
moisture.  
When removing the monitor base, you must lay the monitor face down on a soft  
area to prevent it from getting scratched, defaced, or broken.  
Cleaning the Monitor  
1. Turn off the monitor and the computer.  
2. Unplug the monitor from the wall outlet or the power brick.  
3. Clean the monitor plastics with a clean cloth dampened with water.  
4. Clean the monitor screen with an antistatic screen cleaner.  
CAUTION: Do not use benzene, thinner, ammonia, or any other volatile  
substances to clean the monitor or the screen. These chemicals may damage the  
cabinet finish as well as the screen.  
ENWW  
Maintenance Guidelines  
3
   
3. Setting Up the Monitor  
Unpacking the Monitor  
1. Unpack the monitor. Make sure all contents are included. Store the packing box.  
2. Turn off the computer and other attached devices.  
3. Prepare a flat area to assemble the monitor. You may need a flat, soft, protected  
area for placing the monitor screen-down while preparing it for installation.  
Installing the Monitor  
1. Set the monitor screen face down on a flat, soft, protected table or desk surface  
with the support column overhanging the edge.  
2. Push the base to the monitor support column and fasten the screw to lock it.  
Figure 3-1 Installing the Base  
CAUTION: The screen is fragile. Avoid touching or applying pressure to the LCD  
screen; doing so can cause damage.  
3. Lift the monitor to an upright position and place on a flat, stable surface.  
Figure 3-2 Monitor in Upright Position  
4
Chapter 3. Setting Up the Monitor  
ENWW  
     
Connecting Monitor Cables  
Connecting the VGA (Analog) Cable or DVI-D (Digital) Cable  
Use a VGA video cable or a DVI-D cable to connect your monitor to your computer. To  
use DVI, you must have a DVI-compliant graphic card. Connectors are located on the  
back of the monitor. Be sure the computer and monitor are turned off and unplugged.  
1. To connect the VGA cable (provided with select models)  
Connect one end of the VGA video cable to the back of the monitor and the other end  
to the VGA video connector on the computer.  
2. To connect the DVI-D cable (provided with select models)  
Connect one end of the DVI-D video cable to the back of the monitor and the other  
end to the DVI-D video connector on the computer. You can use this cable only if your  
computer has a DVI compliant graphics card installed. The monitor DVI-D connector  
and cable are included.  
Figure 3-3 Connecting the VGA or a DVI-D cable - connector locations may vary  
High-Bandwidth Digital Content Protection (HDCP)  
Your monitor supports HDCP and can receive high-definition content. High-definition  
content is available in many sources, such as Blue-ray Disc devices or HDTV air or  
cable broadcasts. If you do not have an HDCP-enabled monitor, you will see a blank  
screen or a lower resolution picture when playing high-definition protected content.  
Your computer graphics card and monitor must both support HDCP to display  
protected content.  
Connecting the Power Cable  
1. Follow all Electrical and Power Warnings  
WARNING! To reduce the risk of electric shock or damage to your equipment: Do  
not disable the power cord grounding plug. The grounding plug is an important safety  
feature.  
Plug the power cord into a grounded (earthed) electrical outlet.  
Be sure that the grounded power outlet you plug the power cord into is easily  
accessible to the operator and located as close to the equipment as possible. A power  
cord should be routed so that it is not likely to be walked on or pinched by items that  
are placed upon it or against it.  
Do not place anything on power cords or cables. Arrange them so that no one may  
accidentally step on or trip over them. Do not pull on a cord or cable.  
See"Technical Specification" (Appendix B) for additional information.  
ENWW  
Connecting Monitor Cables  
5
       
Figure 3-4 Connecting the power cable  
2. Connect one end of the power cable to the adapter and the other end to a  
grounded electrical outlet.  
3. Connect the adapter plug to the monitor DC Jack.  
6
Chapter 3. Setting Up the Monitor  
ENWW  
4. Operating the Monitor  
CD Software and Utilities  
The CD that is included with this monitor contains drivers and software that you can  
install on your computer.  
Installing Drivers  
If you determine that you need to update the drivers, you can install the monitor driver  
INF and ICM files from the CD, or download them from the Internet.  
Installing the monitor driver software from the CD  
To install the monitor driver software from the CD:  
1. Insert the CD in your computer CD drive. The CD menu appears.  
2. Select the language.  
3. Click Install Monitor Driver Software .  
4. Follow the on-screen instructions.  
5. Ensure that the proper resolutions and refresh rates appear in the Display Control  
Panel settings.  
Refer to the Windows® operating system documentation for more information.  
NOTE: You might need to install the digitally signed monitor drivers (INF or ICM  
files) manually from the CD, in case of an installation error. Refer to the "Driver  
Software Readme" file on the CD for instructions (in English only).  
Downloading updated drivers from the Internet  
To download the latest version of drivers and software files from the HP Support site:  
1. Refer to: http://www.hp.com/support .  
2. Select your country/region.  
3. Select Download Drivers and Software .  
4. Enter the model number of your monitor. The software download pages for your  
monitor are displayed.  
5. Download and install the driver and software files by following the instructions on  
the download pages.  
6. Ensure that your system meets the requirements.  
ENWW  
CD Software and Utilities 7  
         
Front-Panel Controls  
The monitor buttons are located on the bottom of the front panel  
Figure 4-1 Front-panel control  
button  
No. Icon  
Description  
1
Power  
Turns the monitor on or puts it in standby or sleep mode. The Power  
depending on the model.  
2
3
Menu  
+
Opens, selects, or exits the OSD menu.  
Navigates forward through the OSD menu and increases adjustment  
levels.  
4
5
-
Navigates backward through the OSD menu and decreases adjustment  
levels.  
Auto  
To utilize the auto-adjustment feature, press the key and release it  
immediately. To use input source selection function, press and hold the  
key for 3 seconds (multi-source models).  
Hot Key definition:  
Auto: Auto configure; Press for 3 seconds, Source select  
- : ECO mode select when OSD is not active  
+: Image ratio select when OSD is not active  
8
Appendix 4. Operating the Monitor  
ENWW  
 
Using the On-Screen Display (OSD)  
Main  
Main  
1st Sub  
2nd Sub  
Adjust  
Range  
Menu Item Menu Icon Menu Item Menu Item  
Description  
Reset Value  
Luminance Contrast N/A  
Contrast from Digital-register. 0-100  
Each step will increase/  
Recall Warm  
Contrast Value  
decrease value by 1  
Brightness N/A  
Backlight Adjustment  
Each step will increase/  
decrease value by 1  
0-100  
Recall Warm  
Brightness Value  
Eco Mode  
N/A  
Picture Adjustment,  
Brightness = 90,  
Contrast = 50.  
Standard Recall to  
Standard Mode  
Brightness, Contrast  
Adjustable  
Brightness = 20,  
Text  
Contrast = 50.  
Brightness, Contrast Grayed.  
Brightness = 40,  
Contrast = 50.  
Brightness, Contrast  
Grayed.  
Internet  
Brightness = 60  
Contrast = 50,  
Brightness, Contrast Grayed  
Game  
Movie  
Sports  
On/Off  
Brightness = 80,  
Contrast = 50,  
Brightness, Contrast Grayed  
Brightness = 100,  
Contrast = 50,  
Brightness, Contrast Grayed  
DCR  
N/A  
Dynamic contrast ratio  
Recall Off Value  
ENWW  
Using the On-Screen Display (OSD)  
9
 
Main  
Main  
1st Sub  
2nd Sub  
Adjust  
Range  
Menu Item Menu Icon Menu Item Menu Item  
Description  
Reset Value  
Do Auto  
Image  
Setup  
Clock  
N/A  
Adjust picture Clock to reduce 0-100  
Vertical-Line noise.  
Configure  
Each step will increase/  
decrease value by 1  
Phase  
N/A  
Adjust Picture Phase to  
0-100  
Do Auto  
reduce Horizontal-Line noise.  
Configure  
H. Position N/A  
Adjust the horizontal position 0-100  
of the picture.  
Do Auto  
Configure  
V. Position  
N/A  
N/A  
Adjust the vertical position of 0-100  
the picture.  
Do Auto  
Configure  
Image  
Ratio  
Select Image Aspect Ratio  
Wide  
4:3  
Default to panel  
native aspect ratio  
10 Appendix 4. Operating the Monitor  
ENWW  
Main  
Main  
Sub  
Adjust  
Range  
Menu Item Menu Icon Menu Item  
Description  
Reset Value  
The Color  
Temperature will  
be set to Warm.  
Color Temp.  
Warm  
Normal  
Cool  
Recall Warm Color  
Temperature.  
N/A  
Recall Normal Color  
Temperature.  
N/A  
N/A  
N/A  
The User R/G/B  
value (default is  
50) will be  
modified by Reset  
function in user  
mode.  
Recall Cool Color  
Temperature.  
sRGB  
Recall sRGB Color  
Temperature.  
(for select  
modelswith  
sRGB  
function)  
Red  
Red Gain from Digital-  
register.  
0-100  
0-100  
0-100  
Each step will increase/  
decrease value by 1  
Green  
Blue  
Green Gain from Digital-  
register.  
Each step will increase/  
decrease value by 1  
Blue Gain from Digital-  
register.  
Each step will increase/  
decrease value by 1  
ENWW  
Using the On-Screen Display (OSD) 11  
Main  
Main  
Sub  
Adjust  
Range  
Menu Item Menu Icon Menu Item  
Description  
Reset Value  
OSD Setup  
H. Position Adjust the horizontal position 0-100  
of the OSD.  
Recall 50 Value  
Each step will increase/  
decrease value by 5  
V. Position  
Adjust the vertical position of 0-100  
the OSD.  
Recall 50 Value  
Recall 10 Value  
Each step will increase/  
decrease value by 5  
Timeout  
Adjust the OSD timeout.  
5-100  
Each step will increase/  
decrease value by 5  
Language  
Set OSD display language to  
English. (English is default  
setting)  
No need to recall  
language while  
press "RESET".  
If customer have  
different request,  
please refer to  
customer request  
12 Appendix 4. Operating the Monitor  
ENWW  
Main  
Main  
Sub  
Adjust  
Range  
Menu Item Menu Icon Menu Item  
Description  
Reset Value  
Extra Input Select Select video input signal.  
D-SUB  
Note: Analog-  
Only Model no  
"Input Select"  
item.  
DVI  
DDC/CI  
Reset  
Select DDC/CI on or off  
On  
Off  
Clear each old status of Auto- Yes  
configuration and set the color  
temperature to Warm.  
N/A  
N/A  
Do not execute reset, return  
to main menu.  
No  
Information Show the resolution, H/V  
frequency.  
N/A  
ENWW  
Using the On-Screen Display (OSD) 13  
Selecting Video Input Connectors  
The input connectors are:  
VGA connector (analog)  
DVI-D connector (digital)  
The monitor automatically determines which inputs have valid video signals, and  
displays the image.  
You can connect the VGA cable, the DVI-D cable, or both. If both cables are installed,  
the default input selection is DVI.The source of input can be switched using the Input  
Select option in the OSD menu.  
Identifying Monitor Conditions  
Special messages appear on the monitor screen for the following monitor conditions:  
Input Signal Out of Range - When the Hsync Frequency, Vsync Frequency or  
Resolution is out of the monitor support range, The monitor will show this message.  
No Signal - When the video cable is not connected, or the video cable is connected  
but there is no active signal input, the monitor will show this message, after 9 seconds  
the monitor will enter power saving. This message location is at the position setting in  
"OSD Setup" item.  
Auto Adjustment in Progress - Indicates the auto adjustment function is active. See  
"Adjusting Screen Quality" in this chapter.  
Adjusting Screen Quality  
The auto adjustment feature automatically fine-tunes the image quality for display  
size, position, clock, and phase each time a new video mode is displayed. For more  
precise adjustments of VGA input, run the Auto Adjustment software on the CD. If you  
want additional image quality improvement, use the Clock and Phase controls of the  
monitor to fine tune the image. See "Optimizing Analog Video" in this chapter.  
Optimizing Analog Video  
Some monitors contain advanced circuitry that allow the monitor to function as a  
standard analog monitor. Two controls in the OSD menu can be adjusted to improve  
analog image performance:  
Clock - Increase or decrease the value to minimize any vertical bars or stripes visible  
on the screen background.  
Phase - Increase or decrease the value to minimize video distortion or video jitter.  
Use these controls only when the auto adjustment function does not provide a  
satisfactory monitor image in analog mode. To obtain the best results:  
1. Allow the monitor to warm up for 30 minutes before adjusting.  
2. Access the OSD menu, then select Image Setup.  
3. Set the main Clock settings correctly first, because the Phase settings depend on  
the main Clock settings.When adjusting the Clock and Phase values, if the  
monitor images become distorted,continue adjusting the values until the distortion  
disappears. To restore the factory settings, access the OSD menu, select Factory  
Reset , and then select Yes .  
14 Appendix 4. Operating the Monitor  
ENWW  
     
Power-Saver Feature  
When the monitor is in normal operating mode, the Power light is blue and the monitor  
uses the normal watts of power. For power usage, refer to "Technical Specification"  
(Appendix B). The monitor also supports a power-saver mode that is controlled by the  
computer. When the monitor is in the reduced-power state, the monitor screen is  
blank, the backlight is off, and the Power light is amber. The monitor uses minimum  
power. When the monitor is "awakened," a brief warm-up period occurs before the  
monitor returns to normal operating mode. The energy-saving reduced power state  
activates if the monitor does not detect either the horizontal sync signal or the vertical  
sync signal. The power-saver feature must be activated on your computer for this  
feature to work. Refer to your computer documentation for instructions on setting  
energy-saver features (sometimes called power-management features).  
NOTE: The energy-saver feature works only when the monitor is connected to  
computers that have energy-saver features.  
ENWW  
Power-Saver Feature 15  
 
A. Troubleshooting  
Solving Common Problems  
The following table lists possible problems, the possible cause of each problem, and  
the recommended solutions:  
Problem  
Power LED Is Not ON  
Possible Solutions  
Make sure the power button is ON and the Power Cord is  
properly connected to a grounded power outlet and to the  
monitor.  
Make sure the external power adapter is connected to DC-  
input on the rear of the monitor.  
No Plug & Play  
In order for the Plug & Play feature of the monitor to work,  
you need a Plug & Play compatible computer & video card.  
Check with your computer manufacturer. Also check the  
monitor's video cable and make sure none of the pins are  
bent.  
Make sure the HP Monitor Drivers are installed (HP Monitor  
Drivers are available at : http://www.hp.com/support)  
Picture Is Fuzzy & Has  
Ghosting Shadowing  
Problem  
Adjust the Contrast and Brightness Controls.  
Make sure you are not using an extension cable or switch  
box. We recommend plugging the monitor directly to the  
video card output connector on the back of your computer.  
Picture Bounces, Flickers Or  
Wave Pattern Is Present In  
The Picture  
Move electrical devices that may cause electrical  
interference as far away from the monitor as possible.  
Use the maximum refresh rate your monitor is capable of at  
the resolution your are using.  
Monitor Is Stuck In Active  
Off-Mode  
The Computer Power Switch should be in the ON position.  
The Computer Video Card should be snugly seated in its  
slot.  
Make sure the monitor's video cable is properly connected to  
the computer.  
Inspect the monitor's video cable and make sure none of the  
pins are bent.  
Missing one of the primary  
colors (RED, GREEN, or  
BLUE)  
Inspect the monitor's video cable and make sure that none  
of the pins are bent.  
Make sure the monitor's video cable is properly connected to  
the computer.  
Screen image is not  
centered or sized properly  
Adjust H-Position and V-Position or press hot-key (AUTO).  
Picture has color defects  
(white does not look white)  
Adjust RGB color or select color temperature  
16 Appendix A. Troubleshooting  
ENWW  
   
Problem  
Possible Solutions  
Horizontal or vertical  
disturbances on the screen  
Adjust CLOCK and Phase or press the Auto button to  
display ideal setting. To optimize the screen performance for  
VGA input, use the Auto button button on the monitor and  
the auto-adjustment pattern software utility on the CD  
provided. For DVI input, adjust the video graphics card  
installed in the PC.  
Getting Support from hp.com  
Before you contact customer service, refer to HP Technical Support at:  
Select your country/region, and then follow the links to the support page for your  
monitor.  
Preparing to Call Technical Support  
If you cannot solve a problem by using the troubleshooting tips in this section, you  
might have to call technical support. For technical support contact information, refer to  
the printed documentation included with the monitor.  
Have the following information available when you call:  
• Monitor model number (located on label on back of monitor)  
• Monitor serial number (located on label on back of monitor or in the OSD display  
in the Information menu)  
• Purchase date on invoice  
• Conditions under which the problem occurred  
• Error messages received  
• Hardware configuration  
• Name and version of hardware and software you are using  
Locating the Rating Label  
The rating label on the monitor provides the product number and serial number. You  
may need these numbers when contacting HP about your monitor model.  
The rating label is on the back of the monitor.  
ENWW  
17  
     
B. Technical Specifications  
All specifications represent the typical specifications provided by HP's component  
manufacturers; actual performance may vary either higher or lower.  
HP LCD Monitors  
Face treatment: Glare polarizer with hard coating  
Input terminal:  
VGA connector  
DVI-D 24-pin D-type connector  
Table B-1 Model x20LED  
Specifications:  
Display Type:  
TFT LCD active matrix  
Viewable Image Size  
Tilt  
50.8 cm (20 in.) diagonal  
-4° (+/-2)~+13° (+/-2)  
2.7 kg(5.6 lbs)  
Maximum Weight (unpacked)  
Dimensions (h x w x d)  
491.8 mm x 356.6 mm x 165.9 mm  
19.3 x 14.0 x 6.5 in  
1600 x 900 @ 60 Hz  
1600 x 900 @ 60 Hz  
720x400  
Maximum Graphics Resolution  
Optimum Graphics Resolution  
Text Mode  
Dot Pitch  
0.2768 x 0.2768 mm/0.01 x 0.01 in  
24 to 85 kHz  
Horizontal Frequency (analog mode)  
Vertical Frequency (analog mode)  
Environmental Requirements  
Temperature (independent of altitude)  
Operating Temperature  
50 to 76 Hz  
41° to 104° F (5° to 40° C)  
Non-Operating Temperature  
Relative Humidity (non-condensing)  
Operating Humidity  
-4° to 140° F (-20° to 60° C)  
15% to 90%  
Non-Operating Humidity  
Power Source  
15% to 90%  
100-240V~, 50/60 Hz  
30 watts (W)  
Power Consumption  
Sleep Power Consumption  
<1.0 watts (W)  
ENWW  
18  
     
Table B-2 Model x22LED/ x22LEDc  
Specifications:  
Display Type:  
TFT LCD active matrix  
54.6 cm (21.5 in.) diagonal  
-4° (+/-2)~+13° (+/-2)  
2.9 kg(6.4 lbs)  
Viewable Image Size  
Tilt  
Maximum Weight (unpacked)  
Dimensions (h x w x d)  
525.5 mm x 376.0 mm x 165.9 mm  
20.6 x 14.8 x 6.5 in  
1920 x 1080 @ 60 Hz  
1920 x 1080 @ 60 Hz  
720 x 400  
Maximum Graphics Resolution  
Optimum Graphics Resolution  
Text Mode  
Dot Pitch  
0.248 x 0.248 mm/0.01 x 0.01 in  
24 to 83 kHz  
Horizontal Frequency (analog mode)  
Vertical Frequency (analog mode)  
Environmental Requirements  
Temperature (independent of altitude)  
Operating Temperature  
50 to 75 Hz  
41° to 104° F (5° to 40° C)  
Non-Operating Temperature  
Relative Humidity (non-condensing)  
Operating Humidity  
-4° to 140° F (-20° to 60° C)  
15% to 90%  
Non-Operating Humidity  
Power Source  
15% to 90%  
100-240V~, 50/60 Hz  
30 watts (W)  
Power Consumption  
Sleep Power Consumption  
<1.0 watts (W)  
19 Appendix B. Technical Specifications  
ENWW  
Table B-3 Model x23LED  
Specifications:  
Display Type:  
TFT LCD active matrix  
58.4 cm (23 in.) diagonal  
-4° (+/-2)~+13° (+/-2)  
3.6 kg(7.9 lbs)  
Viewable Image Size  
Tilt  
Maximum Weight (unpacked)  
Dimensions (h x w x d)  
569.3 mm x 407.8 mm x 185.9 mm  
22.4 x 16 x 7.3 in  
1920 x 1080 @ 60 Hz  
1920 x 1080 @ 60 Hz  
720 x 400  
Maximum Graphics Resolution  
Optimum Graphics Resolution  
Text Mode  
Dot Pitch  
0.265 x 0.265 mm/0.01 x 0.01 in  
24 to 83 kHz  
Horizontal Frequency (analog mode)  
Vertical Frequency (analog mode)  
Environmental Requirements  
Temperature (independent of altitude)  
Operating Temperature  
50 to 75 Hz  
41° to 104° F (5° to 40° C)  
Non-Operating Temperature  
Relative Humidity (non-condensing)  
Operating Humidity  
-4° to 140° F (-20° to 60° C)  
15% to 90%  
Non-Operating Humidity  
Power Source  
15% to 90%  
100-240V~, 50/60 Hz  
30 watts (W)  
Power Consumption  
Sleep Power Consumption  
<1.0 watts (W)  
ENWW  
20  
Preset Video Modes  
The monitor automatically recognizes many preset video input modes that will appear  
properly sized and centered on the screen.  
Table B-4 Factory Preset Video Input Modes, x20LED model  
Item  
Preset Resolution  
640 x 480  
Horizontal Frequency (kHz)  
Vertical Frequency (Hz)  
1
2
3
4
5
6
7
8
31.469  
31.469  
37.879  
48.363  
45.00  
59.94  
720 x 400  
70.087  
60.317  
60.004  
60.00  
800 x 600  
1024 x 768  
1280 x720  
1280 x 1024  
1400 x 900  
1600 x 900  
63.981  
55.935  
60.000  
60.02  
59.887  
60.000  
Table B-5 Factory Preset Video Input Modes, x22LED/x22LEDc/x23LED models  
Item  
1
Preset Resolution  
640 x 480  
Horizontal Frequency (kHz)  
Vertical Frequency (Hz)  
59.94  
31.469  
31.469  
37.879  
48.363  
45.000  
60.000  
63.981  
60.000  
75.000  
65.290  
67.500  
2
720 x 400  
70.087  
3
800 x 600  
60.317  
4
1024 x 768  
1280 x720  
60.004  
5
60.000  
6
1280 x 960  
1280 x 1024  
1600 x 900  
1600 x 1200  
1680 x 1050  
1920 x 1080  
60.000  
7
60.020  
8
60.000  
9
60.000  
10  
11  
60.000  
60.000  
21 Appendix B. Technical Specifications  
ENWW  
 
LCD Monitor Quality and Pixel Policy  
Your LCD Monitor uses high-precision technology, manufactured according to high  
standards, to help guarantee trouble-free performance. Nevertheless, the display may  
have cosmetic imperfections that appear as small bright or dark spots. This is  
common to all LCD displays used in products supplied by all vendors and is not  
specific to your LCD Monitor. These imperfections are caused by one or more  
defective pixels or subpixels.  
A pixel consists of one red, one green, and one blue subpixel. A defective whole pixel  
is always turned on (a bright spot on a dark background), or it is always off (a dark  
spot on a bright background). The first is the more visible of the two. A defective  
subpixel (dot defect) is less visible than a defective whole pixel, and is small and only  
visible on a specific background.  
To locate defective pixels, the monitor should be viewed under normal operating  
conditions and in normal operating mode at a supported resolution and refresh rate,  
from a distance of approximately 50 cm (16 inches). We expect that, over time, the  
industry will continue to improve its ability to produce displays with fewer cosmetic  
imperfections, and we will adjust guidelines as improvements are made. For more  
information about your LCD Monitor, refer to the HP Web site at:  
ENWW  
22  
 
C. Agency Regulatory Notices  
Federal Communications Commission Notice  
This equipment has been tested and found to comply with the limits for a Class B  
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to  
provide reasonable protection against harmful interference in a residential installation.  
This equipment generates, uses, and can radiate radio frequency energy and, if not  
installed and used in accordance with the instructions, may cause harmful  
interference to radio communications. However, there is no guarantee that  
interference will not occur in a particular installation. If this equipment does cause  
harmful interference to radio or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and the receiver.  
Connect the equipment into an outlet on a circuit different from that to which the  
receiver is connected.  
Consult the dealer or an experienced radio or television technician for help.  
Modifications  
The FCC requires the user to be notified that any changes or modifications made to  
this device that are not expressly approved by Hewlett Packard Company may void  
the user's authority to operate the equipment.  
Cables  
Connections to this device must be made with shielded cables with metallic RFI/EMI  
connector hoods to maintain compliance with FCC Rules and Regulations.  
ENWW  
23  
       
Declaration of Conformity for Products Marked with the FCC Logo  
(United States Only)  
This device complies with Part 15 of the FCC Rules. Operation is subject to the  
following two conditions:  
1. This device may not cause harmful interference.  
2. This device must accept any interference received, including interference that  
may cause undesired operation.  
For questions regarding the product, contact:  
Hewlett Packard Company  
P. O. Box 692000, Mail Stop 530113  
Houston, Texas 77269-2000  
Or, call 1-800-HP-INVENT (1-800 474-6836)  
For questions regarding this FCC declaration, contact:  
Hewlett Packard Company  
P. O. Box 692000, Mail Stop 510101  
Houston, Texas 77269-2000  
Or, call (281) 514-3333  
To identify this product, refer to the Part, Series, or Model number found on the  
product.  
Canadian Notice  
This Class B digital apparatus meets all requirements of the Canadian Interference-  
Causing Equipment Regulations.  
Avis Canadien  
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement  
sur le matériel brouilleur du Canada.  
European Union Regulatory Notice  
This product complies with the following EU Directives:  
• Low Voltage Directive 2006/95/EC  
• EMC Directive 2004/108/EC  
• Ecodesign Directive 2009/125/EC where applicable  
CE compliance of this product is valid only if powered with the correct CE-marked AC  
adapter provided by HP.  
Compliance with these directives implies conformity to applicable harmonized  
European standards (European Norms) which are listed on the EU Declaration of  
Conformity issued by Hewlett-Packard for this product or product family.  
This compliance is indicated by the following conformity markings placed on the  
product:  
24 Appendix C. Agency Regulatory Notices  
ENWW  
     
This marking is valid for non-Telecom products  
and EU harmonized Telecom products (e.g. Bluetooth). xxxx*  
This marking is valid for EU non-harmonized Telecom products .  
*Notified body number (used only if applicable - refer to the product label)  
The official EU CE declaration of conformity for this device may be found at  
The point of contact for regulatory matters is Hewlett-Packard GmbH, HQ-TRE,  
Herrenberger Strasse 140, 71034 Boeblingen, Germany.  
German Ergonomics Notice  
HP products which bear the "GS" approval mark, when forming part of a system  
comprising HP brand computers, keyboards and monitors that bear the "GS" approval  
mark, meet the applicable ergonomic requirements. The installation guides included  
with the products provide configuration information.  
Japanese Notice  
Korean Notice  
ENWW  
25  
   
Power Cord Set Requirements  
The monitor power supply is provided with Automatic Line Switching (ALS). This  
feature allows the monitor to operate on input voltages between 100120V~ or 200−  
240V.  
The power cord set (flexible cord or wall plug) received with the monitor meets the  
requirements for use in the country where you purchased the equipment.  
If you need to obtain a power cord for a different country, you should purchase a  
power cord that is approved for use in that country.  
The power cord must be rated for the product and for the voltage and current marked  
on the product's electrical ratings label. The voltage and current rating of the cord  
should be greater than the voltage and current rating marked on the product. In  
addition, the cross-sectional area of the wire must be a minimum of 0.75 mm2 or 18  
AWG, and the length of the cord must be between 6 feet (1.8 m) and 12 feet (3.6 m).  
If you have questions about the type of power cord to use, contact an authorized HP  
service provider. A power cord should be routed so that it is not likely to be walked on  
or pinched by items placed upon it or against it. Particular attention should be paid to  
the plug, electrical outlet, and the point where the cord exits from the product.  
Japanese Power Cord Requirements  
For use in Japan, use only the power cord received with this product.  
CAUTION: Do not use the power cord received with this product on any other  
products.  
Product Environmental Notices  
Materials Disposal  
This HP product contains mercury in the fluorescent lamp in the display LCD that  
might require special handling at end-of-life.  
Disposal of this material can be regulated because of environmental considerations.  
For disposal or recycling information, contact the local authorities or the Electronic  
Industries Alliance (EIA)  
26 Appendix C. Agency Regulatory Notices  
ENWW  
     
Disposal of Waste Equipment by Users in  
Private Household in the European Union  
This symbol on the product or on its packaging indicates that this product must not be  
disposed of with your household waste. Instead, it is your responsibility to dispose of  
your waste equipment by handing it over to a designated collection point for the  
recycling or waste electrical and electronic equipment. The separate collection and  
recycling of your waste equipment at the time of disposal will help to conserve natural  
resources and ensure that it is recycled in a manner that protects human health and  
the environment. For more information about where you can drop off your waste  
equipment for recycling, please contact the local city office, the household waste  
disposal service or the shop where you purchased the product.  
Chemical Substances  
HP is committed to providing our customers with information about the chemical  
substances in our products as needed to comply with legal requirements such as  
REACH (Regulation EC No 1907/2006 of the European Parliament and Council). A  
chemical information report for this product can be found at  
HP Recycling Program  
HP encourages customers to recycle used electronic hardware, HP original print  
cartridges, and rechargeable batteries. For more information about recycling  
Restriction of Hazardous Substances (RoHS)  
A Japanese regulatory requirement, defined by specification JIS C 0950, 2005,  
mandates that manufacturers provide Material Content Declarations for certain  
categories of electronic products offered for sale after July 1, 2006. To view the JIS C  
ENWW  
27  
       
Turkey EEE Regulation  
In Conformity with the EEE Regulation  
EEE Yönetmeliğine Uygundur  
ENWW  
28  
 

Indesit KT6G2W User Manual
Intel 520 120 Gb 2 5&quot; Internal Solid State Drive SSDSC2BW120A301 User Manual
Intel Core I7 Quad Core I7 2600k 3 4ghz Desktop Processor BX80623i72600K User Manual
Lenovo THINKCENTRE 6396 User Manual
Memorex 3202xxxx User Manual
MicroBoards Technology CopyWriter Series User Manual
Philips 20MT2136 User Manual
Philips 21PT166A User Manual
Philips 28PW9763 User Manual
Philips RC4420 User Manual