HP Hewlett Packard Hewlett Packard Computer Monitor ZR22W User Manual

HP ZR22w and ZR24w LCD Monitors  
User Guide  
About This Guide  
This guide provides information on setting up the monitor, installing drivers, using the on-screen display  
menu, troubleshooting and technical specifications.  
WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily  
harm or loss of life.  
CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage  
to equipment or loss of information.  
NOTE: Text set off in this manner provides important supplemental information.  
ENWW  
iii  
iv  
About This Guide  
ENWW  
Table of contents  
2 Safety and Maintenance Guidelines  
3 Setting Up the Monitor  
4 Operating the Monitor  
ENWW  
v
Appendix A Troubleshooting  
Appendix B Technical Specifications  
Appendix C Agency Regulatory Notices  
vi  
ENWW  
viii  
ENWW  
1 Product Features  
HP ZR22w and ZR24w Models  
The LCD (liquid crystal display) monitor has an active matrix, thin-film transistor (TFT). The monitor  
features include:  
ZR22w model, 54.61 cm (21.5-inch) diagonal viewable area display with 1920 × 1080 resolution,  
plus full-screen support for lower resolutions  
ZR24w model, 61 cm (24-inch) diagonal viewable area display with 1920 × 1200 resolution, plus  
full-screen support for lower resolutions  
Wide viewing angle to allow viewing from a sitting or standing position, or moving side-to-side  
Pivot capability to rotate the display from landscape to portrait mode  
Tilt, swivel, and height adjustment capabilities  
Removable stand for flexible mounting solutions with HP Quick Release and VESA 100 mm  
mounting holes  
Video signal input to support VGA analog with VGA signal cable provided  
Video signal input to support DVI digital with DVI-D signal cable provided  
Video signal input to support DisplayPort digital with DisplayPort signal cable provided  
USB 2.0 hub with one upstream (connects to the computer) and four downstream (connects to  
USB devices) ports  
USB cable included to connect to the monitor's USB hub and to a USB connector on a computer  
Supports the optional HP speaker bar (purchased separately)  
Plug and play capability if supported by the system  
Privacy filter slots to insert filters (purchased separately) to block side screen viewing  
Security slot provision on rear of monitor for optional cable lock  
Cable management feature for placement of cables and cords  
On-Screen Display (OSD) adjustments in several languages for ease of setup and screen  
optimization  
HP Display Assistant utility software for adjusting monitor settings and enabling the theft deterrence  
feature  
ENWW  
HP ZR22w and ZR24w Models  
1
   
Pivot Pro software for viewing information on the screen in portrait mode  
HDCP (High-Bandwidth Digital Content Protection) copy protection on DVI and DisplayPort inputs  
Software and documentation CD that includes monitor drivers and product documentation  
Energy saver feature to meet requirements for reduced power consumption  
Energy Star qualified (ZR22w model only)  
Intelligent Management AssetControl  
Compliant with the following regulated specifications:  
European Union CE Directives  
Swedish MPR II 1990  
Swedish TCO Requirements  
2
Chapter 1 Product Features  
ENWW  
2 Safety and Maintenance Guidelines  
Important Safety Information  
A power cord is included with the monitor. If another cord is used, use only a power source and  
connection appropriate for this monitor. For information on the correct power cord set to use with the  
monitor, refer to the Power Cord Set Requirements on page 41 in Appendix C.  
WARNING! To reduce the risk of electric shock or damage to the equipment:  
• Do not disable the power cord grounding feature. The grounding plug is an important safety feature.  
• Plug the power cord in a grounded (earthed) outlet that is easily accessible at all times.  
• Disconnect power from the product by unplugging the power cord from the electrical outlet.  
For your safety, do not place anything on power cords or cables. Arrange them so that no one may  
accidentally step on or trip over them. Do not pull on a cord or cable. When unplugging from the electrical  
outlet, grasp the cord by the plug.  
To reduce the risk of serious injury, read the Safety and Comfort Guide. It describes proper workstation,  
setup, posture, and health and work habits for computer users, and provides important electrical and  
mechanical safety information. This guide is located on the Web at http://www.hp.com/ergo and/or on  
the documentation CD, if one is included with the monitor.  
CAUTION: For the protection of the monitor, as well as the computer, connect all power cords for the  
computer and its peripheral devices (such as a monitor, printer, scanner) to some form of surge  
protection device such as a power strip or Uninterruptible Power Supply (UPS). Not all power strips  
provide surge protection; the power strips must be specifically labeled as having this ability. Use a power  
strip whose manufacturer offers a Damage Replacement Policy so you can replace the equipment, if  
surge protection fails.  
Use the appropriate and correctly sized furniture designed to properly support your HP LCD monitor.  
WARNING! LCD monitors that are inappropriately situated on dressers, bookcases, shelves, desks,  
speakers, chests, or carts may fall over and cause personal injury.  
Care should be taken to route all cords and cables connected to the LCD monitor so that they can not  
be pulled, grabbed, or tripped over.  
ENWW  
Important Safety Information  
3
   
Maintenance Guidelines  
To enhance the performance and extend the life of the monitor:  
Do not open the monitor cabinet or attempt to service this product yourself. Adjust only those  
controls that are covered in the operating instructions. If the monitor is not operating properly or  
has been dropped or damaged, contact an authorized HP dealer, reseller, or service provider.  
Use only a power source and connection appropriate for this monitor, as indicated on the label/  
back plate of the monitor.  
Be sure the total ampere rating of the products connected to the outlet does not exceed the current  
rating of the electrical outlet, and the total ampere rating of the products connected to the cord does  
not exceed the rating of the cord. Look on the power label to determine the ampere rating (AMPS  
or A) for each device.  
Install the monitor near an outlet that you can easily reach. Disconnect the monitor by grasping the  
plug firmly and pulling it from the outlet. Never disconnect the monitor by pulling the cord.  
Turn the monitor off when not in use. You can substantially increase the life expectancy of the  
monitor by using a screen saver program and turning off the monitor when not in use.  
NOTE: Monitors with a “burned-in image” are not covered under the HP warranty.  
Slots and openings in the cabinet are provided for ventilation. These openings must not be blocked  
or covered. Never push objects of any kind into cabinet slots or other openings.  
Do not drop the monitor or place it on an unstable surface.  
Do not allow anything to rest on the power cord. Do not walk on the cord.  
Keep the monitor in a well-ventilated area, away from excessive light, heat or moisture.  
When removing the monitor base, you must lay the monitor face down on a soft area to prevent it  
from getting scratched, defaced, or broken.  
Cleaning the Monitor  
1. Turn off the monitor and unplug the power cord from the back of the unit.  
2. Dust the monitor by wiping the screen and the cabinet with a soft, clean antistatic cloth.  
3. For more difficult cleaning situations, use a 50/50 mix of water and Isopropyl alcohol.  
CAUTION: Spray the cleaner onto a cloth and use the damp cloth to gently wipe the screen surface.  
Never spray the cleaner directly on the screen surface. It may run behind the bezel and damage the  
electronics.  
CAUTION: Do not use cleaners that contain any petroleum based materials such as benzene, thinner,  
or any volatile substance to clean the monitor screen or cabinet. These chemicals may damage the  
monitor.  
Shipping the Monitor  
Keep the original packing box in a storage area. You may need it later if you move or ship the monitor.  
4
Chapter 2 Safety and Maintenance Guidelines  
ENWW  
     
3 Setting Up the Monitor  
To set up the monitor, ensure that the power is turned off to the monitor, computer system, and other  
attached devices, then follow the instructions below.  
NOTE: Be sure the master power switch, located on the rear panel of the monitor, is in the off position.  
The master power switch turns off all power to the monitor.  
Installing the Monitor Pedestal Base  
NOTE: Do not install the pedestal base if the monitor will be used on a wall, swing arm, or other  
mounting fixture; instead see Mounting the Monitor on page 13 in this chapter.  
1. Using both hands, position the monitor over the pedestal base.  
CAUTION: Do not touch the surface of the LCD panel. Pressure on the panel may cause non-  
uniformity of color or disorientation of the liquid crystals. If this occurs the screen will not recover  
to its normal condition.  
2. Press down firmly on the monitor to lock the pedestal base in place. When the base locks, it will  
make a clicking sound.  
Figure 3-1 Inserting the Monitor into the Pedestal Base  
NOTE: Be sure the pedestal base is securely locked before continuing with the setup.  
ENWW  
Installing the Monitor Pedestal Base  
5
   
Rear Components  
HP ZR22w and ZR24w Models  
Figure 3-2 Rear Components  
Table 3-1 Rear Components  
Component  
Function  
1
2
3
4
5
6
7
8
9
Cable Lock Provision  
Master Power Switch  
AC Power Connector  
DisplayPort Connector  
DVI-D Connector  
Provides slot for use with cable security locks.  
Turns off all power to the monitor.  
Connects the AC power cord to the monitor.  
Connects the DisplayPort cable to the monitor.  
Connects the DVI-D cable to the monitor.  
Connects the VGA cable to the monitor.  
VGA Connector  
USB Upstream Connector  
USB Downstream Connectors  
Connects the monitor USB hub cable to a host USB port/hub.  
Connects optional USB devices to the monitor.  
Connects optional USB devices to the monitor.  
USB Downstream Connectors  
(side panel)  
6
Chapter 3 Setting Up the Monitor  
ENWW  
   
Routing and Connecting the Cables  
1. Place the monitor in a convenient, well-ventilated location near the computer.  
2. Remove the cable routing cover by pulling it straight off the front of the column.  
Figure 3-3 Removing the Cable Routing Cover  
3. Before connecting the cables, route them through the cable routing hole in the column (1) and  
replace the cable routing cover (2).  
Figure 3-4 Routing Cables  
4. Connect a VGA signal cable, DVI-D signal cable, or DisplayPort signal cable.  
ENWW  
Routing and Connecting the Cables  
7
 
NOTE: The monitor is capable of supporting either analog or digital input. The video mode is  
determined by the video cable used. The monitor will automatically determine which inputs have  
valid video signals. The inputs can be selected by pressing the +/Source button on the front panel  
or through the On-Screen Display (OSD) feature by pressing the Menu button.  
For analog operation, use the VGA signal cable provided. Connect the VGA signal cable to  
the VGA connector on the rear of the monitor and the other end to the VGA connector on the  
computer.  
For DVI digital operation, use the DVI-D signal cable provided. Connect the DVI-D signal cable  
to the DVI connector on the rear of the monitor and the other end to the DVI connector on the  
computer.  
For DisplayPort digital operation, use the DisplayPort signal cable provided. Connect the  
DisplayPort signal cable to the DisplayPort connector on the rear of the monitor and the other  
end to the DisplayPort connector on the computer.  
5. Connect one end of the provided USB cable to the USB hub connector on the rear panel of the  
computer, and the other end to the upstream USB connector on the monitor.  
6. Connect one end of the power cable to the AC power connector on the back of the monitor, and  
the other end to an electrical wall outlet.  
Figure 3-5 Connecting the Cables  
WARNING! To reduce the risk of electric shock or damage to the equipment:  
Do not disable the power cord grounding plug. The grounding plug is an important safety feature.  
Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times.  
Disconnect power from the equipment by unplugging the power cord from the electrical outlet.  
For your safety, do not place anything on power cords or cables. Arrange them so that no one may  
accidentally step on or trip over them. Do not pull on a cord or cable. When unplugging from the electrical  
outlet, grasp the cord by the plug.  
8
Chapter 3 Setting Up the Monitor  
ENWW  
Connecting USB Devices  
The monitor provides USB connectors on the side panel and on the rear panel that can be used to  
connect devices such as a digital camera, USB keyboard, or USB mouse.  
NOTE: You must connect the USB hub cable from the monitor to the computer to enable the USB 2.0  
ports on the monitor. Refer to Step 5 in Routing and Connecting the Cables on page 7.  
Figure 3-6 Connecting USB Devices  
Adjusting the Monitor  
1. Tilt the monitor's panel forward or backward to set it to a comfortable eye level.  
Figure 3-7 Tilting the Monitor  
ENWW  
Connecting USB Devices  
9
   
2. Swivel the monitor to the left or right for the best viewing angle.  
Figure 3-8 Swiveling the Monitor  
3. Adjust the monitor's height so that it is parallel to your eye height for a comfortable viewing position.  
A lock-down/release button on the back of the column prevents the display head from sliding up  
when the monitor is lifted. If the display head is locked in the lowest height position:  
a. Make sure that the monitor is safely positioned on a stable surface.  
b. Gently push down on the display head (1).  
c. While pushing down the display head, press the lock-down/release button on the back of the  
column (2).  
d. Guide the display head up to the desired height (3).  
Figure 3-9 Adjusting the Height  
10 Chapter 3 Setting Up the Monitor  
ENWW  
4. Raise the monitor panel to its highest position and pivot the monitor clockwise from landscape to  
portrait orientation viewing to adapt to your application.  
NOTE: It may be necessary to tilt the monitor panel back to prevent the corner of the panel from  
coming in contact with the base when pivoting.  
Figure 3-10 Pivoting the Monitor  
NOTE: To view information on the screen in portrait mode, you will need to install the Pivot Pro  
software included on the software and documentation CD. The position of the OSD menu can also  
be rotated to portrait mode. To rotate the OSD menu, press the Menu button on the monitor's front  
panel, then select OSD Control > Rotate OSD.  
Turning on the Monitor  
1. Ensure that the master power switch on the rear of the monitor is in the On position.  
2. Press the power button on the computer to turn it on.  
3. Press the power button on the front of the monitor to turn it on.  
CAUTION: Burn-in image damage may occur on monitors that display the same static image on  
screen for a prolonged period of time.* To avoid burn-in image damage on the monitor screen, you  
should always activate a screen saver application or turn off the monitor when it is not in use for a  
prolonged period of time. Image retention is a condition that may occur on all LCD screens. Monitors  
with a “burned-in image” are not covered under the HP warranty.  
* A prolonged period of time is 12 consecutive hours of non-use.  
NOTE: If pressing the power button has no effect, the Power Button Lockout feature may be enabled.  
To disable this feature, press and hold the monitor power button for 10 seconds.  
NOTE: You can disable the power LED in the OSD menu. Press the Menu button on the front of the  
monitor, then select Management > Bezel Power LED > Off.  
When the monitor is powered on, a Monitor Status message is displayed for five seconds. The message  
shows which input (DisplayPort, DVI, or VGA) is the current active signal, the status of the auto-switch  
source setting (On or Off; factory default is On), the default source signal (factory default is DisplayPort),  
the current preset display resolution, and the recommended preset display resolution.  
ENWW  
Turning on the Monitor 11  
 
The monitor automatically scans the signal inputs for an active input and uses that input for the display.  
If two or more inputs are active, the monitor will display the default input source. If the default source is  
not one of the active inputs, then the monitor will display the highest ranking priority input in the following  
order: DisplayPort, DVI, then VGA. You can change the default source in the OSD by pressing the front  
panel menu button and selecting Source Control > Default Source.  
Removing the Monitor Pedestal Base  
You can remove the monitor panel from the pedestal base to mount the panel on a wall, a swing arm,  
or other mounting fixture (purchased separately).  
This monitor has a Quick Release mechanism that allows you to easily remove and replace the monitor  
panel to the pedestal base.  
CAUTION: Before beginning to disassemble the monitor, be sure the monitor is turned off and the  
power and signal cables are both disconnected. Also disconnect any USB cables that are connected to  
the monitor.  
1. Disconnect and remove the signal and power cables from the back of the monitor.  
2. Slide the quick release latch (1) on the pedestal base to the side (either right or left).  
3. Pull up on the monitor display head (2) to remove it from the base.  
Figure 3-11 Removing the Monitor from the Pedestal Base  
12 Chapter 3 Setting Up the Monitor  
ENWW  
 
Mounting the Monitor  
NOTE: This apparatus is intended to be supported by UL or CSA Listed wall mount bracket.  
The HP Quick Release can be removed from the pedestal base and installed to a mounting fixture. It  
allows you to quickly and securely attach the monitor panel to the mounting fixture.  
1. Remove the monitor panel from the pedestal base. Refer to Removing the Monitor Pedestal  
Base on page 12 in the previous section.  
CAUTION: This monitor supports the VESA industry standard 100 mm mounting holes. To attach  
a third-party mounting solution to the monitor, four 4 mm, 0.7 pitch, and 10 mm long screws are  
required (not provided with the monitor). Longer screws must not be used because they may  
damage the monitor. It is important to verify that the manufacturer’s mounting solution is compliant  
with the VESA standard and is rated to support the weight of the monitor display panel. For best  
performance, it is important to use the power and video cables provided with the monitor.  
2. Remove the Quick Release from the pedestal base by removing the four screws.  
Figure 3-12 Removing the HP Quick Release from the Pedestal Base  
ENWW  
Removing the Monitor Pedestal Base 13  
 
3. Mount the Quick Release to a swing arm or other mounting fixture using the four screws removed  
from the Quick Release in the previous step.  
Figure 3-13 Installing the Quick Release  
CAUTION: The Quick Release can also be installed directly to a wall to mount the monitor panel.  
It is designed to support a maximum of up to 10.9 kg (24 lbs). If you are mounting to a wall, HP  
recommends that you consult with a qualified engineering, architectural, or construction  
professional to determine the appropriate type and quantity of mounting fasteners required for your  
application and to ensure that the mounting solution is properly installed to support applied loads.  
4. Insert the monitor panel into the Quick Release, and then press down firmly on the monitor to lock  
it in place. When the Quick Release locks, it will make a clicking sound.  
Figure 3-14 Inserting the Monitor Panel into the Quick Release  
14 Chapter 3 Setting Up the Monitor  
ENWW  
Locating the Rating Labels  
The rating labels on the monitor provide the spare part number, product number, and serial number.  
You may need these numbers when contacting HP about the monitor model. The rating labels are  
located on the rear panel of the monitor display head.  
Figure 3-15 Locating the Rating Labels  
Installing a Cable Lock  
You can secure the monitor to a fixed object with an optional cable lock available from HP.  
ENWW  
Locating the Rating Labels 15  
   
4 Operating the Monitor  
Software and Utilities  
The CD that comes with the monitor contains files you can install on the computer:  
an .INF (Information) file  
an .ICM (Image Color Matching) file  
auto-adjustment pattern utility  
additional software for the monitor model  
NOTE: If the monitor does not include a CD, the .INF and .ICM files can be downloaded from the HP  
monitors support Web site. See Downloading from the Internet on page 17 in this chapter.  
The Information File  
The .INF file defines monitor resources used by Microsoft Windows operating systems to ensure monitor  
compatibility with the computer’s graphics adapter.  
This monitor is Microsoft Windows Plug and Play compatible and the monitor will work correctly without  
installing the .INF file. Monitor Plug and Play compatibility requires that the computer’s graphic card is  
VESA DDC2–compliant and that the monitor connects directly to the graphics card. Plug and Play does  
not work through separate BNC type connectors or through distribution buffers/boxes.  
The Image Color Matching File  
The .ICM files are data files that are used in conjunction with graphics programs to provide consistent  
color matching from monitor screen to printer, or from scanner to monitor screen. This file is activated  
from within graphics programs that support this feature.  
NOTE: The ICM color profile is written in accordance with the International Color Consortium (ICC)  
Profile Format specification.  
16 Chapter 4 Operating the Monitor  
ENWW  
       
Installing the .INF and .ICM Files  
After you determine that you need to update, you can install the .INF and .ICM files from the CD or  
download them.  
Installing from the CD  
To install the .INF and .ICM files on the computer from the CD:  
1. Insert the CD in the computer CD-ROM drive. The CD menu is displayed.  
2. View the Monitor Driver Software Readme file.  
3. Select Install Monitor Driver Software.  
4. Follow the on-screen instructions.  
5. Ensure that the proper resolution and refresh rates appear in the Windows Display control panel.  
NOTE: You may need to install the digitally signed monitor .INF and .ICM files manually from the CD  
in the event of an installation error. Refer to the Monitor Driver Software Readme file on the CD.  
Downloading from the Internet  
To download the latest version of .INF and .ICM files from the HP monitors support Web site:  
1. Refer to http://www.hp.com/support and select the country region.  
2. Follow the links for the monitor to the support page and download page.  
3. Ensure the system meets the requirements.  
4. Download the software by following the instructions.  
ENWW  
Installing the .INF and .ICM Files 17  
     
Using the Auto-Adjustment Function  
You can optimize the screen performance for the VGA (analog) input by using the OK/auto button on  
the monitor and the auto-adjustment pattern software utility on the CD provided.  
Do not use this procedure if the monitor is using a DVI or DisplayPort input. If the monitor is using a  
VGA (analog) input, this procedure can correct the following image quality conditions:  
Fuzzy or unclear focus  
Ghosting, streaking or shadowing effects  
Faint vertical bars  
Thin, horizontal scrolling lines  
An off-center picture  
To use the auto-adjustment feature:  
1. Allow the monitor to warm up for 20 minutes before adjusting.  
2. Press the OK/auto button on the monitor front panel.  
You can also press the Menu button, then select Image Control > Auto-Adjustment from  
the OSD Main Menu. Refer to Adjusting the Monitor Settings on page 20 in this chapter.  
If the result is not satisfactory, continue with the procedure.  
3. Insert the CD in the disc drive. The CD menu is displayed.  
4. Select Open Auto-Adjustment Software. The setup test pattern is displayed.  
5. Press the OK/auto button on the monitor front panel to produce a stable, centered image.  
6. Press the ESC key or any other key on the keyboard to exit the test pattern.  
18 Chapter 4 Operating the Monitor  
ENWW  
 
Front Panel Controls  
Table 4-1 Monitor Front Panel Controls  
Control  
Function  
1
2
Menu  
Minus  
Opens, selects or exits the OSD menu.  
If the OSD menu is on, press to navigate backward through  
the OSD menu and decrease adjustment levels.  
3
Plus/source  
If the OSD menu is on, press to navigate forward through the  
OSD menu and increase adjustment levels.  
If the OSD menu is inactive, press to activate the source  
button that chooses the video signal input (VGA, DVI, or  
DisplayPort)  
4
OK/auto  
If the OSD menu is on, press to select the highlighted menu  
item.  
If the OSD menu is inactive, press to activate the auto  
adjustment feature to optimize the screen image.  
5
6
Power  
Turns the monitor on or off as long as the master power  
switch on the rear panel is on.  
Power LED  
Blue = Fully powered.  
Amber = Sleep mode.  
Flashing Amber = Sleep Timer mode.  
ENWW  
Front Panel Controls 19  
 
Adjusting the Monitor Settings  
The monitor settings can be adjusted from the On-Screen Display (OSD) menu or from the HP Display  
Assistant utility.  
NOTE: If there is a problem with the display settings, try resetting the settings to the factory defaults  
by opening the OSD and selecting Factory Reset from the OSD menu.  
Using the On-Screen Display Menu  
Use the On-Screen Display (OSD) to adjust the screen image based on your viewing preferences. To  
access the OSD, do the following:  
1. If the monitor is not already on, press the Power button to turn on the monitor.  
2. To access the OSD Menu, press the Menu button on the monitor’s front panel.  
3. To navigate through the OSD Menu, press the + (Plus) button on the monitor’s front panel to scroll  
up, or the (Minus) button to scroll down.  
4. To select an item from the OSD Menu, use the + or buttons to scroll to and highlight your selection,  
then press the OK button to select that function.  
5. Adjust the item using the + or buttons on the front panel to adjust the scale.  
6. After adjusting the function, select Save and Return, or Cancel if you don’t want to save the setting,  
then select Exit from the Main Menu.  
NOTE: If the buttons remain untouched for 30 seconds (factory default) while displaying a menu, the  
firmware will save the current adjustments and exit. Also, if the video controller changes video mode  
while the OSD is active, the current (adjusted) settings will not be saved, the OSD will be turned off, and  
the new mode will be displayed.  
20 Chapter 4 Operating the Monitor  
ENWW  
   
OSD Menu Selections  
The following table lists the On-Screen Display (OSD) menu selections and their functional descriptions.  
After changing an OSD menu item, and if the menu screen has these options, you may choose to:  
Cancel—to return to the previous menu level.  
Save and Return—to save all changes and return to the OSD Main Menu screen. This Save and  
Return option is only active if you change a menu item.  
Table 4-2 OSD Menu  
Icon  
Main Menu  
Submenu  
Description  
Brightness  
Adjustable scale  
Adjusts the brightness level of the screen. The factory  
default range is 90.  
Contrast  
Color  
Adjustable scale  
Adjusts the contrast level of the screen. The factory  
default range is 80.  
Selects the screen color. The factory default is 6500K  
or Custom Color, depending on the model.  
5000 K - Warm  
Produces a slightly reddish white color.  
6500 K - sRGB  
Standard color temperature for sRGB (the industry  
standard color space for most general use).  
9300 K - Cool  
Custom (RGB)  
Produces a slightly bluish white color.  
Selects and adjusts your own color scales:  
R—sets your own red color levels  
G—sets your own green color levels  
B—sets your own blue color levels  
Image Control  
Adjusts the screen image. (VGA input only)  
Auto Adjustment  
Clock  
Automatically adjusts the screen image (VGA input  
only).  
Minimizes any vertical bars or strips visible on the  
screen background. Adjusting the Clock will also  
change the horizontal screen image.  
Clock Phase  
Adjusts the focus of the display. This adjustment  
allows you to remove any horizontal noise and clear or  
sharpen the image of characters.  
Horizontal Position  
Vertical Position  
Adjusts the position of the screen image left and right.  
Adjusts the position of the screen image up and down.  
ENWW  
Adjusting the Monitor Settings 21  
 
Table 4-2 OSD Menu (continued)  
Icon  
Main Menu  
Submenu  
Description  
Custom Scaling  
Selects the method on how displayed information on  
the monitor will be formatted. Select:  
Fill to Screen - image fills the entire screen and  
may look distorted or elongated because of non-  
proportional scaling of height and width  
Fill to Aspect Ratio - image is sized to fit the  
screen and maintains proportional image  
Overscan - Supports over-scanning of the image  
for DVI-D and DisplayPort inputs. This option can  
be set to:  
Off  
On  
Sharpness  
Adjusts the screen image to look sharper or soft.  
Video Overdrive  
Turns Video Overdrive On or Off. The factory default  
is Off.  
Dynamic Contrast Ratio Turns Dynamic Contrast Ratio On or Off. The factory  
default is Off.  
OSD Control  
Provides a menu for adjusting the on-screen display  
(OSD) controls.  
Horizontal OSD  
Position  
Changes the viewing position of the OSD menu to the  
left or right area of the screen. The factory default  
range is 50.  
Vertical OSD Position  
Changes the viewing position of the OSD menu to the  
top or bottom area of the screen. The factory default  
range is 50.  
OSD Transparency  
OSD Timeout  
Adjust to view the background information through the  
OSD.  
Sets the time duration in seconds that the OSD is  
visible after the last button is pressed. The range is 5  
– 60 seconds. The factory default is 30 seconds.  
Rotate OSD  
Power Saver  
Rotates the OSD menus and messages to support the  
monitor's pivot feature. The choices are Landscape  
and Portrait.  
Management  
Selects the OSD and power management features of  
the monitor.  
Enables the power saving feature. Select:  
On  
Off  
The factory default is On.  
22 Chapter 4 Operating the Monitor  
ENWW  
Table 4-2 OSD Menu (continued)  
Icon  
Main Menu  
Submenu  
Description  
Power On Recall  
Restores power to the monitor following an  
unexpected removal of power. Select:  
On  
Off  
The factory default is On.  
Mode Display  
Displays the resolution, refresh rate and frequency  
information on the screen each time the OSD Main  
Menu is accessed. Select:  
On  
Off  
The factory default is On.  
Monitor Status  
Displays the operating status of the monitor each time  
the monitor is powered on. Select the location to  
display the status to:  
Top  
Middle  
Bottom  
Off  
The factory default is Top.  
DDC/CI Support  
Allows the computer to control some OSD menu  
features such as brightness, contrast and color  
temperature. Set to:  
On  
Off  
The factory default is On.  
Bezel Power LED  
Sleep Timer  
Turns off the power LED on the front panel of the  
monitor. The factory default is On.  
Provides the timer adjustment menu options:  
Set Current Time—sets the current time in hours  
and minutes  
Set Sleep Time—sets the time you want to place  
the monitor in sleep mode  
Set on Time—sets the time you want the monitor  
to wake up from sleep mode  
Timer—sets the Sleep Timer feature On or Off.  
The default setting is Off.  
Sleep Now—immediately sets the monitor to  
enter sleep mode  
Language  
Selects the language in which the OSD menu is  
displayed. The factory default is English.  
ENWW  
Adjusting the Monitor Settings 23  
Table 4-2 OSD Menu (continued)  
Icon  
Main Menu  
Submenu  
Description  
Information  
Selects and displays important information about the  
monitor.  
Current Settings  
Provides the current input video mode.  
Recommended  
Settings  
Provides the recommended resolution mode and  
refresh rate for the monitor.  
Serial Number  
Reports the serial number of the monitor. The serial  
number is needed if contacting HP technical support.  
FW Version  
Reports the firmware version of the monitor.  
Reports the total hours of backlight operation.  
Backlight Hours  
Service Support  
Factory Reset  
Source Control  
Returns all OSD menu settings and DDC/CI controls  
to the factory default settings, except the Language.  
Selects the video input signal. DisplayPort is the  
factory default.  
DisplayPort  
DVI  
Selects DisplayPort as the video input signal.  
Selects DVI as the video input signal.  
Selects VGA as the video input signal.  
VGA  
Default Source  
Selects the default or primary video input signal when  
the monitor is connected to two active and valid video  
sources. The monitor will automatically determine the  
video format. The choices are:  
DisplayPort  
DVI  
VGA  
The factory default is DisplayPort.  
Auto-Switch Source  
Source Detection  
Turns the system's automatic video signal input to On  
or Off. The factory default is On.  
This option is displayed in the OSD when a DisplayPort  
input is selected. You can set Source Detection to:  
Always Active  
Low Power  
The factory default is Low Power.  
Exits the OSD menu screen.  
Exit  
24 Chapter 4 Operating the Monitor  
ENWW  
Optimizing Digital Conversion  
Two controls in the on-screen display can be adjusted to improve image performance: Clock and Clock  
Phase.  
NOTE: The Clock and Clock Phase controls are adjustable only when using an analog input. These  
controls are not adjustable for digital inputs.  
The Clock must first be set correctly since the Clock Phase settings are dependent on the main Clock  
setting. Use these controls only when the auto-adjustment function does not provide a satisfactory  
image.  
Clock—Increases/decreases the value to minimize any vertical bars or stripes visible on the screen  
background.  
Clock Phase—Increases/decreases the value to minimize video distortion or video jitter.  
NOTE: When using the controls, you will obtain the best results by using the auto-adjustment pattern  
software utility provided on the CD.  
When adjusting the Clock and Clock Phase values, if the monitor images become distorted, continue  
adjusting the values until the distortion disappears. To restore the factory settings, select Yes from the  
Factory Reset menu in the on-screen display.  
Using the HP Display Assistant Utility  
HP Display Assistant, included on the software and documentation CD, is a software utility that guides  
you through the tuning process with easy to understand instructions and background patterns designed  
for each monitor control. It provides:  
Accurate screen calibration through the use of step-by-step instruction Wizards to obtain the best  
overall image quality.  
Software control of the monitor image and color settings to eliminate dependence on the monitor’s  
front panel buttons and On-Screen Display (OSD) menu.  
Defined preset display settings for each individual user in a multi-user environment.  
Multiple preset display settings for a single user based on content and ambient lighting.  
Asset Management and Power Management capabilities that include remote control for individual  
or a group of displays on the domain from a centralized console application.  
Power Saving Plug-in feature that applies power saving modes to the display and a schedule power  
saving feature that allows the display to be set to idle (stand-by) mode or powered off after a pre-  
determined time of inactivity.  
The HP Display Assistant Utility has two modes of operation: Wizard and OSD mode. The preferred  
method of use is Wizard mode, which takes you through a step-by-step process to accurately calibrate  
the monitor. This method relies on a sequence of steps that will obtain the best display results when  
completed.  
NOTE: Refer to the HP Display Assistant user guide for additional information about the software.  
ENWW  
Adjusting the Monitor Settings 25  
   
Identifying Monitor Conditions  
Special messages will appear on the monitor screen when identifying the following monitor conditions:  
Monitor Status—When the monitor is powered on or when the input source signal is changed, a  
Monitor Status message is displayed for five seconds. The message shows which input is the  
current active signal, the status of the auto-switch source setting (On or Off), the default source  
signal, the current preset display resolution, and the recommended preset display resolution.  
Input Signal Out of Range—Change resolution setting to 1920 x 1080 – 60Hz—Indicates the  
monitor does not support the input signal because the resolution and/or refresh rate are set higher  
than the monitor supports (model ZR22w).  
Input Signal Out of Range—Change resolution setting to 1920 x 1200 – 60Hz—Indicates the  
monitor does not support the input signal because the resolution and/or refresh rate are set higher  
than the monitor supports (model ZR24w).  
No Source Signal—Indicates the monitor is not receiving a video signal from the PC on the monitor  
video input connector. Check to determine if the PC or input signal source is off or in the power  
saving mode.  
Auto Adjustment in Progress—Indicates the auto-adjustment function is active.  
Monitor Going to Sleep—Indicates the screen display is entering a sleep mode.  
Check Video Cable—Indicates the video cable is not properly connected to the computer.  
OSD Lockout—The OSD can be enabled or disabled by pressing and holding the Menu button  
on the front panel for 10 seconds. If the OSD is locked, the warning message OSD Lockout  
displays for ten seconds.  
If the OSD is locked, press and hold the Menu button for 10 seconds to unlock the OSD.  
If the OSD is unlocked, press and hold the Menu button for 10 seconds to lock the OSD.  
Power Button Lockout—Indicates the power button is locked. If the power button is locked, the  
warning message Power Button Lockout displays.  
If the power button is locked, press and hold the power button for 10 seconds to unlock the  
power button function.  
If the power button is unlocked, press and hold the power button for 10 seconds to lock out  
the power button function.  
Theft Mode Enabled—Indicates that theft deterrence mode has been activated. Theft deterrence  
is an optional feature that can be set up in HP Display Assistant. Theft deterrence mode is triggered  
if both the power and display cables have been disconnected from the monitor, the monitor is  
reconnected to a different computer, and the theft deterrence PIN number is not entered within the  
elapsed time. When the monitor is in theft deterrence mode, all front panel buttons are disabled  
other than the power button.  
26 Chapter 4 Operating the Monitor  
ENWW  
 
Sleep Timer Mode  
The Sleep Timer mode is an energy-saving feature that enables you to set a time for the monitor to  
power on and off at the same time every day. This also extends the life of the backlight bulbs in the  
monitor. The Sleep Timer has five settings:  
Set Current Time  
Set Sleep Time  
Set On Time  
Timer: On/Off  
Sleep Now  
To set the timer:  
1. Press the Menu button on the monitor front panel to display the OSD Menu.  
2. Scroll down and highlight Management.  
3. Press the OK button to select Management.  
4. Scroll down and highlight and select Sleep Timer > Set Current Time.  
NOTE: You must set the current local time before you reset the time for Sleep Time or On  
Time. Note that the time is displayed in a 24–hour clock format. For example, 1:15 p.m. is displayed  
as 13 hours 15 minutes.  
A power failure or loss of power to the monitor will cause the timer to reset to 00:00. If this occurs,  
you will need to reset the sleep timer mode.  
5. Press the OK button once to enter the adjustment mode for hours.  
6. Press the - (Minus) or + (Plus) button to adjust the hour.  
7. Press the OK button again to enter the time for minutes.  
8. Press the - (Minus) or + (Plus) button to adjust the minutes.  
9. Press the OK button to lock in the time chosen.  
10. After setting the current time, the highlight automatically skips to Set Sleep Time. Repeat steps 6  
through 9 to set Sleep Time.  
11. If you do not want to set Sleep Time, press the OK button twice, then select Save and Return to  
exit the menu.  
12. After setting Sleep Time, the highlight automatically skips to Set On Time. Repeat steps 6 through  
9 to set On Time.  
13. Set the Timer mode to On to activate the Sleep Timer settings.  
14. When you are finished, select Save and Return to exit the menu.  
The fifth selection, Sleep Now, turns the monitor backlights off immediately and stays in sleep mode  
until the next On Time activates or a monitor button is pressed.  
ENWW  
Sleep Timer Mode 27  
 
HP Display LiteSaver  
HP Display LiteSaver is a software application, available on the CD, that increases monitor life and  
saves energy. It allows you to place the monitor into its low power sleep mode at predefined times by  
shutting down or reducing power to most internal circuits. This helps protect the LCD panel against  
image retention. Image retention can occur when the monitor is left on while displaying the same image  
for an extended period of time, leaving a shadow of the image on the screen.  
Installing the HP Display LiteSaver Software  
1. Insert the CD in the computer CD-ROM Drive. The CD menu is displayed.  
2. Select Install HP Display LiteSaver Software.  
3. After installing the software, click the HP Display LiteSaver icon in the Windows system tray or  
right-click the icon and select Configure from the pop-up menu.  
4. Select the following options to configure the HP Display LiteSaver features:  
Table 4-3 HP Display LiteSaver Configuration Options  
Select This Option  
To Do This  
Enable Display LiteSaver  
Enables the HP Display LiteSaver functions; deselect to disable the HP Display  
LiteSaver.  
Display Off  
Sets the time when the monitor automatically turns off. This does not affect screen  
saver operation, which has priority over the HP Display LiteSaver.  
Display On  
Sets the time when the monitor automatically turns on. This does not affect screen  
saver operation, which has priority over the HP Display LiteSaver.  
Activity Extension  
Sets the time in minutes before the monitor turns off if there is any keyboard or mouse  
activity after the Display Off time is reached. If the keyboard or mouse is used, then  
HP Display LiteSaver waits until the set amount of time before turning the display  
off again. Set to 0 to disable. If disabled, the monitor will turn off as soon as the  
Display Off time is reached, regardless of keyboard or mouse activity.  
Show 1 minute Display Off Notice  
Displays a popup message in the system tray 1 minute before the monitor is turned  
off by HP Display LiteSaver.  
Status  
OK  
Shows the time until the monitor is next due to be turned off by HP Display LiteSaver.  
Stores the current settings and minimizes HP Display LiteSaver to the System Tray.  
Cancel  
Restores the previous settings and minimizes HP Display LiteSaver to the System  
Tray. HP Display LiteSaver will continue to run.  
Help  
Exit  
Opens the online help file.  
Exits and closes the HP Display LiteSaver. It will no longer control the monitor power  
until it is next run.  
View HP Display LiteSaver Readme on the CD for additional information on how to configure HP Display  
LiteSaver.  
28 Chapter 4 Operating the Monitor  
ENWW  
   
sRGB Support  
The monitor is designed to support sRGB for color management, which adapts to the color standards  
used in the image technology industry.  
To take advantage of the sRGB support, you will need to change the monitor’s color temperature to  
sRGB and install the sRGB color profile (ICM) file.  
NOTE: The sRGB color temperature preset will improve the color accuracy of sRGB images on the  
computer monitor, but some color variation may still occur.  
Changing the Color Temperature  
1. Press the Menu button on the front panel of the monitor to launch the Main Menu of the OSD.  
2. Select Color.  
3. Select 6500 K - sRGB.  
4. Select Save and Return to exit the menu.  
Installing the sRGB ICM File for Microsoft Windows 2000 and Windows XP  
NOTE: To complete the following procedure, you must be logged in as an administrator or a member  
of the administrator’s group. If the computer is connected to a network, network policy settings may  
prevent you from completing this procedure. The sRGB ICM file does not support Windows 95 and  
Windows NT operating systems.  
1. Click the Display icon in the Control Panel.  
2. In the Display Properties windows, select the Settings tab, then click the Advanced button.  
3. Select the Color Management tab, then click the Add button to open the Add Profile  
Association dialog box.  
4. Select the sRGB Color Space Profile.icm file, then click the Add button  
5. To activate a color profile for the monitor, you must set it as the Default Monitor Profile. Select  
sRGB Color Space Profile, then click Set as Default button.  
6. Click Apply or OK.  
Installing the sRGB ICM File for Microsoft Windows Vista  
1. Click Appearance and Personalization icon in the Control Panel.  
2. Click Personalization.  
3. Click Display Settings.  
4. Click the Advanced Settings button.  
5. Click the Color Management tab, then click the Color Management button.  
6. Click the Advanced tab, then click the Change System Defaults button.  
7. On the Devices tab, click the Add button.  
ENWW  
sRGB Support 29  
       
8. Select the RGB Color Space Profile.icm file, then click the OK button.  
9. To activate a color profile for the monitor, you must set it as the Default Monitor Profile. Select  
sRGB Color Space Profile, then click the Set as Default button.  
Installing the sRGB ICM File for Microsoft Windows 7  
1. Click Appearance and Personalization icon in the Control Panel.  
2. Click Display.  
3. Click Change display settings.  
4. Click Advanced settings.  
5. Click the Color Management tab, then click the Color Management button.  
6. Click the Advanced tab, then click the Change System Defaults button.  
7. On the Devices tab, click the Add button.  
8. Select the RGB Color Space Profile.icm file, then click the OK button.  
9. To activate a color profile for the monitor, you must set it as the Default Monitor Profile. Select  
sRGB Color Space Profile, then click the Set as Default button.  
30 Chapter 4 Operating the Monitor  
ENWW  
 
A Troubleshooting  
Solving Common Problems  
The following table lists possible problems, the possible cause of each problem, and the recommended  
solutions.  
Problem  
Possible Cause  
Solution  
Screen is blank.  
Power cord is disconnected.  
Connect the power cord.  
Master power switch on the  
monitor's rear panel is turned  
off.  
Set the master power switch to the on position (I) and  
press the front panel power button.  
Power button on front panel of Check that the master power switch on the rear of  
the monitor is turned off.  
the monitor is set to the on (I) position. Press the front  
panel power button.  
NOTE: If pressing the power button has no effect,  
press and hold the power button for 10 seconds to  
disable the power button lockout feature.  
Video cable is improperly  
connected.  
Connect the video cable properly. Refer to Chapter  
information.  
Screen blanking is active.  
Press any key on the keyboard or move the mouse  
to inactivate the screen blanking utility.  
Screen image appears distorted; text is The computer’s graphics card Set the computer’s display resolution to the same  
fuzzy or blurred; image quality is  
degraded.  
resolution is set lower or higher mode as the monitor’s recommended native screen  
than the monitor’s native  
resolution.  
resolution to provide the best picture quality.  
Image appears blurred, indistinct, or  
too dark.  
Brightness and contrast are  
too low.  
Press the OK/auto button on the front panel. If this  
does not correct the image, press the Menu button  
to open the OSD Menu, and adjust the brightness  
and contrast scales as needed.  
Image is not centered  
Position may need adjustment. Press the Menu button to access the OSD menu.  
Select Image Control/Horizontal Position or Vertical  
Position to adjust the horizontal or vertical position  
of the image.  
Check Video Cable is displayed on  
screen.  
Monitor video cable is  
disconnected.  
Connect the appropriate video cable (DisplayPort,  
DVI, or VGA) between the computer and monitor. Be  
sure that the computer power is off while connecting  
the video cable.  
ENWW  
Solving Common Problems 31  
   
Problem  
Possible Cause  
Solution  
Input Signal Out of Range. Change  
Settings to 1920 × 1080 @ 60Hz  
(ZR22w model) OR Input Signal Out the monitor supports.  
of Range. Change settings to 1920 x  
1200 @ 60 Hz (ZR24w model) is  
Video resolution and/or refresh Restart the computer and enter Safe Mode. Change  
rate are set higher than what  
the settings to a supported setting (see Recognizing  
the computer so that the new settings take effect.  
displayed on screen.  
HP Display LiteSaver doesn't turn off  
the monitor screen.  
The Activity Extension time  
has not elapsed.  
The default Activity Extension value is set to 10  
minutes. The HP Display LiteSaver will wait to detect  
no input or movement from the keyboard or mouse  
for 10 consecutive minutes after the Display Off time  
has passed, before the monitor enters into low-  
power mode. For example, if the Display Off time is  
set to 5 minutes from the current time and the Activity  
Extension is set to 10 minutes, the HP Display  
LiteSaver will not actually turn off the display until 10  
minutes of inactivity has elapsed, even though the  
Display Off time is 5 minutes from now.  
The HP Display LiteSaver may The monitor screen should turn off if the system is  
not be compatible with the  
computer system. Some  
compatible. To turn the monitor back on, wait 5  
seconds and move the mouse.  
notebook computers are not  
compatible and the monitor  
power can not be controlled.  
NOTE: If the monitor did not turn off, then the  
computer graphics driver is not compatible with the  
HP Display LiteSaver software.  
The monitor is off but it did not seem to The monitor's power saving  
In the monitor's OSD menu, select Management  
> Power Saver. The control should be set to On to  
allow the monitor to enter into low-power modes.  
enter into a low-power sleep mode.  
control is disabled.  
OSD Lockout is displayed.  
The monitor's OSD Lockout  
function is enabled.  
Press and hold the Menu button for 10 seconds to  
disable the OSD Lockout function.  
Power Button Lockout is displayed.  
The monitor's Power Button  
Lockout function is enabled.  
Press and hold the Power button for 10 seconds to  
unlock the power button function.  
Online Technical Support  
For the online access to technical support information, self-solve tools, online assistance, community  
forums of IT experts, broad mutlivendor knowledge base, monitoring and diagnostic tools, go to  
Preparing to Call Technical Support  
If you cannot solve a problem using the troubleshooting tips in this section, you may need to call technical  
support. Have the following information available when you call:  
Monitor model number  
Monitor serial number  
Purchase date on invoice  
Conditions under which the problem occurred  
Error messages received  
32 Appendix A Troubleshooting  
ENWW  
   
Hardware configuration  
Name and version of the hardware and software you are using  
ENWW  
Preparing to Call Technical Support 33  
B Technical Specifications  
NOTE: All performance specifications are provided by the component manufacturers. Performance  
specifications represent the highest specification of all HP's component manufacturers' typical level  
specifications for performance and actual performance may vary either higher or lower.  
ZR22w Model  
Table B-1 ZR22w Specifications  
Display  
54.61 cm wide screen  
TFT LCD  
21.5 inches wide screen  
21.5–inch diagonal  
Type  
Viewable Image Size  
Tilt  
54.61 cm diagonal  
-5 to 30°  
Swivel  
-45 to 45°  
Maximum Weight (Unpacked)  
Dimensions (include base)  
Height (highest position)  
Height (lowest position)  
Depth  
7.0 kg  
15.43 lbs.  
45.62 cm  
17.96 inches  
14.42 inches  
9.04 inches  
19.98 inches  
36.62 cm  
22.96 cm  
50.74 cm  
Width  
Maximum Graphic Resolution  
1920 x 1080 (60 Hz) analog input  
1920 x 1080 (60 Hz) digital input  
1920 x 1080 (60 Hz) analog input  
1920 x 1080 (60 Hz) digital input  
720 × 400  
Optimum Graphic Resolution  
Text Mode  
Dot Pitch  
0.2475 (H) × 0.2475 (W) mm  
96 PPI  
Pixels Per Inch  
Horizontal Frequency  
Vertical Refresh Rate  
24 to 80 kHz  
50 to 76 Hz  
34 Appendix B Technical Specifications  
ENWW  
   
Table B-1 ZR22w Specifications (continued)  
Environmental Requirements Temperature  
5 to 35° C  
41 to 95° F  
-4 to 140° F  
Operating Temperature  
Storage Temperature  
Relative Humidity  
Power Source  
-20 to 60° C  
20 to 80%  
100 – 240 VAC, 50/60 Hz  
Altitude:  
0 to 5000 m  
0 to 12192 m  
44 watts  
0 to 16,400 feet  
0 to 40,000 feet  
Operating  
Storage  
Power Consumption (maximum)  
Input Terminal  
One VGA connector with cable included;  
one DVI connector with cable included;  
one DisplayPort connector with cable  
included  
ZR24w Model  
Table B-2 ZR24w Specifications  
Display  
60.96 cm wide screen  
TFT LCD  
24 inches wide screen  
24–inch diagonal  
Type  
Viewable Image Size  
Tilt  
60.96 cm diagonal  
-5 to 30°  
Swivel  
-45 to 45°  
Maximum Weight (Unpacked)  
Dimensions (include base)  
Height (highest position)  
Height (lowest position)  
Depth  
8.20 kg  
18.04 lbs.  
45.9 cm  
18.07 inches  
16.71 inches  
9.236 inches  
21.9 inches  
42.45 cm  
23.529 cm  
55.64 cm  
Width  
Maximum Graphic Resolution  
1920 x 1200 (60 Hz) analog input  
1920 x 1200 (60 Hz) digital input  
1920 x 1200 (60 Hz) analog input  
1920 x 1200 (60 Hz) digital input  
640 × 480  
Optimum Graphic Resolution  
Text Mode  
Dot Pitch  
0.270 (H) x 0.270 (W) mm  
94 PPI  
Pixels Per Inch  
Horizontal Frequency  
24 to 80 kHz  
ENWW  
ZR24w Model 35  
 
Table B-2 ZR24w Specifications (continued)  
Vertical Refresh Rate  
59 to 61 Hz  
Environmental Requirements Temperature  
5 to 35° C  
41 to 95° F  
-4 to 140° F  
Operating Temperature  
Storage Temperature  
Relative Humidity  
Power Source  
-20 to 60° C  
20 to 80%  
100 – 240 VAC, 50/60 Hz  
Altitude:  
0 to 5000 m  
0 to 12192 m  
100 watts  
0 to 16,400 feet  
0 to 40,000 feet  
Operating  
Storage  
Power Consumption (maximum)  
Input Terminal  
One VGA connector with cable included;  
one DVI connector with cable included;  
one DisplayPort connector with cable  
included  
Recognizing Preset Display Resolutions  
The display resolutions listed below are the most commonly used modes and are set as factory defaults.  
This monitor automatically recognizes these preset modes and they will appear properly sized and  
centered on the screen.  
ZR22w Model  
Table B-3 Factory Preset Modes  
Preset  
Pixel Format  
640 × 480  
Horz Freq (kHz)  
31.469  
37.861  
37.500  
31.469  
37.879  
48.363  
44.86  
Vert Freq (Hz)  
59.940  
72.809  
75.00  
1
2
640 × 480  
3
640 × 480  
4
720 × 400  
70.087  
60.317  
60.004  
60.00  
5
800 × 600  
6
1024 × 768  
1152 × 720  
1280 × 720  
1280 × 768  
1280 × 800  
1280 × 960  
1280 × 1024  
1366 × 768  
7
8
44.77  
59.86  
9
47.396  
49.702  
60.00  
60.00  
10  
11  
12  
13  
59.810  
60.00  
63.98  
60.02  
47.71  
59.79  
36 Appendix B Technical Specifications  
ENWW  
   
Table B-3 Factory Preset Modes (continued)  
14  
15  
16  
17  
18  
19  
20  
1440 × 900  
1440 × 900  
1600 × 900  
1600 × 1000  
1600 × 1200  
1680 × 1050  
1920 × 1080  
55.94  
55.469  
60.0  
59.89  
59.901  
60.0  
61.648  
75.00  
65.29  
67.5  
60.00  
60.00  
60.00  
60.00  
ZR24w Model  
Table B-4 Factory Preset Modes  
Preset  
Pixel Format  
640 × 480  
Horz Freq (kHz)  
31.469  
31.469  
37.879  
48.363  
60.00  
Vert Freq (Hz)  
59.940  
70.087  
60.317  
60.004  
60.00  
1
2
720 × 400  
3
800 × 600  
4
1024 × 768  
1280 × 960  
1280 × 1024  
1440 × 900  
1600 × 1200  
1680 × 1050  
1920 × 1080  
1920 × 1200  
1920 × 1200  
5
6
63.981  
55.935  
75.00  
60.02  
7
59.887  
60.00  
8
9
65.29  
60.00  
10  
11  
12  
67.50  
60.00  
74.038  
74.556  
59.95  
59.885  
Entering User Modes  
The video controller signal may occasionally call for a mode that is not preset if:  
You are not using a standard graphics adapter.  
You are not using a preset mode.  
It this occurs, you may need to readjust the parameters of the monitor screen by using the on-screen  
display. Your changes can be made to any or all of these modes and saved in memory. The monitor  
automatically stores the new setting, then recognizes the new mode just as it does a preset mode. In  
addition to the factory preset modes, there are fifteen to twenty user modes, depending on the model,  
that can be entered and stored.  
ENWW  
Entering User Modes 37  
   
Energy Saver Feature  
When the monitor is in its normal operating mode, the monitor uses less than 28.5 watts (ZR22w model)  
or 95 watts (ZR24w model) and the Power light is blue.  
The monitor also supports a reduced power state. The reduced power state will be entered into if the  
monitor detects the absence of either the horizontal sync signal and/or the vertical sync signal. Upon  
detecting the absence of these signals, the monitor screen is blanked, the backlight is turned off, and  
the power light is turned amber. When the monitor is in the reduced power state, the monitor will utilize  
less than 2 watts of power. There is a brief warm up period before the monitor will return to its normal  
operating mode.  
Refer to the computer manual for instructions on setting energy saver features (sometimes called power  
management features).  
NOTE: The above power saver feature only works when connected to computers that have energy  
saver features.  
By selecting the settings in the monitor's Energy Saver utility, you can also program the monitor to enter  
into the reduced power state at a predetermined time. When the monitor's Energy Saver utility causes  
the monitor to enter the reduced power state, the power light blinks amber.  
38 Appendix B Technical Specifications  
ENWW  
 
C Agency Regulatory Notices  
Federal Communications Commission Notice  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant  
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful  
interference in a residential installation. This equipment generates, uses, and can radiate radio  
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful  
interference to radio communications. However, there is no guarantee that interference will not occur  
in a particular installation. If this equipment does cause harmful interference to radio or television  
reception, which can be determined by turning the equipment off and on, the user is encouraged to try  
to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and the receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is  
connected.  
Consult the dealer or an experienced radio or television technician for help.  
Modifications  
The FCC requires the user to be notified that any changes or modifications made to this device that are  
not expressly approved by Hewlett Packard Company may void the user's authority to operate the  
equipment.  
Cables  
Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods  
to maintain compliance with FCC Rules and Regulations.  
Declaration of Conformity for Products Marked with the  
FCC Logo (United States Only)  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  
1. This device may not cause harmful interference.  
2. This device must accept any interference received, including interference that may cause  
undesired operation.  
For questions regarding the product, contact:  
ENWW  
Federal Communications Commission Notice 39  
         
Hewlett Packard Company  
P. O. Box 692000, Mail Stop 530113  
Houston, Texas 77269-2000  
Or, call 1-800-HP-INVENT (1-800 474-6836)  
For questions regarding this FCC declaration, contact:  
Hewlett Packard Company  
P. O. Box 692000, Mail Stop 510101  
Houston, Texas 77269-2000  
Or, call (281) 514-3333  
To identify this product, refer to the Part, Series, or Model number found on the product.  
Canadian Notice  
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment  
Regulations.  
Avis Canadien  
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel  
brouilleur du Canada.  
European Union Regulatory Notice  
This product complies with the following EU Directives:  
Low Voltage Directive 2006/95/EC  
EMC Directive 2004/108/EC  
Compliance with these directives implies conformity to applicable harmonized European standards  
(European Norms) which are listed on the EU Declaration of Conformity issued by Hewlett-Packard for  
this product or product family.  
This compliance is indicated by the following conformity marking placed on the product:  
This marking is valid for non-Telecom  
This marking is valid for EU non-  
products and EU harmonized Telecom harmonized Telecom products.  
products (e.g. Bluetooth)  
*Notified body number (used only if  
applicable — refer to the product label).  
40 Appendix C Agency Regulatory Notices  
ENWW  
     
Hewlett-Packard GmbH, HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, Germany  
The official EU CE declaration of conformity for this device may be found at http://www.hp.com/go/  
German Ergonomics Notice  
HP products which bear the “GS” approval mark, when forming part of a system comprising HP brand  
computers, keyboards and monitors that bear the “GS” approval mark, meet the applicable ergonomic  
requirements. The installation guides included with the products provide configuration information.  
Japanese Notice  
Korean Notice  
Power Cord Set Requirements  
The monitor power supply is provided with Automatic Line Switching (ALS). This feature allows the  
monitor to operate on input voltages between 100–120V or 200–240V.  
The power cord set (flexible cord or wall plug) received with the monitor meets the requirements for use  
in the country where you purchased the equipment.  
If you need to obtain a power cord for a different country, you should purchase a power cord that is  
approved for use in that country.  
The power cord must be rated for the product and for the voltage and current marked on the product's  
electrical ratings label. The voltage and current rating of the cord should be greater than the voltage and  
current rating marked on the product. In addition, the cross-sectional area of the wire must be a minimum  
of 0.75 mm² or 18 AWG, and the length of the cord must be between 6 feet (1.8 m) and 12 feet (3.6 m).  
If you have questions about the type of power cord to use, contact an authorized HP service provider.  
A power cord should be routed so that it is not likely to be walked on or pinched by items placed upon  
it or against it. Particular attention should be paid to the plug, electrical outlet, and the point where the  
cord exits from the product.  
ENWW  
German Ergonomics Notice 41  
       
Japanese Power Cord Requirements  
For use in Japan, use only the power cord received with this product.  
CAUTION: Do not use the power cord received with this product on any other products.  
Product Environmental Notices  
ENERGY STAR® Qualification (Select Models)  
HP Displays marked with the ENERGY STAR® certification mark meet the requirements of the U.S.  
Environmental Protection Agency (EPA) ENERGY STAR program. The EPA ENERGY STAR®  
certification mark does not imply endorsement by the EPA. As an ENERGY STAR Partner, Hewlett  
Packard Company has determined that this product meets the ENERGY STAR® program requirements  
for display energy efficiency.  
The following ENERGY STAR® certification mark appears on all ENERGY STAR qualified displays:  
The ENERGY STAR® program specifications for displays and computers were created by the EPA to  
promote energy efficiency and reduce air pollution through more energy-efficient equipment in homes,  
offices, and factories. One way products achieve this goal is by using the Microsoft Windows power  
management feature to reduce power consumption when the product is not in use.  
The power management feature enables the computer to initiate a low-power or “sleep” mode after a  
period of user inactivity. When used with an external ENERGY STAR® qualified display, this feature  
also supports similar power management features for the display. To take advantage of these potential  
energy savings, users should use the default power management settings that are provided with  
ENERGY STAR qualified computers and displays. The default power management settings on  
ENERGY STAR qualified computers are preset to behave in the following ways when the system is  
operating on AC power:  
Turn off an external display after 15 minutes of user inactivity  
Initiate a low power sleep mode for the computer after 30 minutes of user inactivity  
ENERGY STAR® qualified computers exit the low power sleep mode and ENERGY STAR qualified  
displays resume operation when the user resumes use of the computer. Examples include the user  
pressing the power/sleep button, receiving an input signal from an input device, receiving an input signal  
from a network connection with the Wake On LAN (WOL) feature enabled, etc.  
Additional information on the ENERGY STAR® program, its environmental benefits and the potential  
energy and financial savings of the power management feature can be found on the EPA ENERGY  
STAR Power Management Web site at http://www.energystar.gov/powermanagement.  
42 Appendix C Agency Regulatory Notices  
ENWW  
     
Materials Disposal  
This HP product contains mercury in the fluorescent lamp in the display LCD that might require special  
handling at end-of-life.  
Disposal of this material can be regulated because of environmental considerations. For disposal or  
recycling information, contact the local authorities or the Electronic Industries Alliance (EIA)  
Disposal of Waste Equipment by Users in Private Household in the  
European Union  
This symbol on the product or on its packaging indicates that this product must not be disposed of with  
your household waste. Instead, it is your responsibility to dispose of your waste equipment by handing  
it over to a designated collection point for the recycling or waste electrical and electronic equipment.  
The separate collection and recycling of your waste equipment at the time of disposal will help to  
conserve natural resources and ensure that it is recycled in a manner that protects human health and  
the environment. For more information about where you can drop off your waste equipment for recycling,  
please contact the local city office, the household waste disposal service or the shop where you  
purchased the product.  
HP Recycling Program  
HP encourages customers to recycle used electronic hardware, HP original print cartridges, and  
rechargeable batteries. For more information about recycling programs, go to http://www.hp.com/  
Chemical Substances  
HP is committed to providing our customers with information about the chemical substances in our  
products as needed to comply with legal requirements such as REACH (Regulation EC No 1907/2006  
of the European Parliament and Council). A chemical information report for this product can be found  
Restriction of Hazardous Substances (RoHS)  
A Japanese regulatory requirement, defined by specification JIS C 0950, 2005, mandates that  
manufacturers provide Material Content Declarations for certain categories of electronic products  
offered for sale after July 1, 2006. To view the JIS C 0950 material declaration for this product, visit  
ENWW  
Product Environmental Notices 43  
         
11363-2006  
11363-2006  
Turkey EEE Regulation  
In Conformity with the EEE Regulation  
EEE Yönetmeliğine Uygundur  
44 Appendix C Agency Regulatory Notices  
ENWW  
 
D LCD Monitor Quality and Pixel Policy  
The TFT monitor uses high-precision technology, manufactured according to HP standards, to  
guarantee trouble-free performance. Nevertheless, the display may have cosmetic imperfections that  
appear as small bright or dark spots. This is common to all LCD displays used in products supplied by  
all vendors and is not specific to the HP LCD. These imperfections are caused by one or more defective  
pixels or sub-pixels.  
A pixel consists of one red, one green, and one blue sub-pixel.  
A defective whole pixel is always turned on (a bright spot on a dark background), or it is always off  
(a dark spot on a bright background). The first is the more visible of the two.  
A defective sub-pixel (dot defect) is less visible than a defective whole pixel and is small and only  
visible on a specific background.  
To locate defective pixels, the monitor should be viewed under normal operating conditions, in normal  
operating mode at a supported resolution and refresh rate, from a distance of approximately 50 cm (20  
in).  
HP expects that, over time, the industry will continue to improve its ability to produce LCDs with fewer  
cosmetic imperfections and HP will adjust guidelines as improvements are made.  
ENWW  
45  
 

HP Hewlett Packard Hewlett Packard Computer Monitor 2211X User Manual
Electrolux E30EC70FSS User Manual
Carrier 38QV036320 User Manual
BT 3205 User Manual
BT 3000 Classic User Manual
Bang Olufsen BeoCom Beocom 6000 User Manual
AT T E5901 User Manual
Asus Computer Monitor VK221 User Manual
Asus Computer Hardware P4P800SE User Manual
ADC L997 User Manual