HP Hewlett Packard Hewlett Packard Computer Monitor LP2465 User Manual

HP LP1965 19", LP2065 20", and LP2465  
24" LCD Monitors  
User Guideꢀꢀ  
About This Guide  
This guide provides information on setting up the monitor, installing drivers, using the on-screen  
display menu, troubleshooting and technical specifications.  
WARNING! Text set off in this manner indicates that failure to follow directions could result  
in bodily harm or loss of life.  
CAUTION Text set off in this manner indicates that failure to follow directions could result in  
damage to equipment or loss of information.  
NOTE Text set off in this manner provides important supplemental information.  
iii  
iv  
About This Guide  
Table of contentsꢀꢀ  
v
vi  
1 Product Features  
HP LP1965, LP2065, and LP2465 Models  
The flat panel monitors have an active matrix, thin-film transistor (TFT), liquid crystal display (LCD).  
The monitor features include:  
ꢀꢀ LP1965 model, large 19-inch (48.3 cm) viewable area display with 1280 × 1024 resolution, plus  
full-screen support for lower resolutions  
ꢀꢀ LP2065 model, large 20.1-inch (51 cm) viewable area display with 1600 × 1200 resolution, plus  
full-screen support for lower resolutions  
ꢀꢀ LP2465 model, large 24-inch (61 cm) viewable area display with 1920 × 1200 resolution, plus  
full-screen support for lower resolutions  
ꢀꢀ Wide viewing angle to allow viewing from a sitting or standing position, or moving side-to-side  
ꢀꢀ Pivot capability to rotate display to portrait mode  
ꢀꢀ Tilt, swivel, and height adjustment capabilities  
ꢀꢀ Removable stand with quick release mechanism and VESA 100 mm mounting holes for flexible  
mounting solutions  
ꢀꢀ Video inputs support DVI analog and digital signal inputs  
ꢀꢀ Two DVI-I to VGA signal cables and two DVI-D signal cables included (LP2065 and LP2465  
models)  
ꢀꢀ One DVI-I to VGA signal cable and one DVI-D signal cable included (LP1965 model only)  
ꢀꢀ USB 2.0 hub with one upstream (connects to the computer) and four downstream (connects to  
USB devices) ports  
ꢀꢀ USB cable included to connect the monitor's USB hub to the USB connector on the computer  
ꢀꢀ Accessory rail on monitor to accept optional mounted devices, such as an HP speaker bar  
ꢀꢀ Plug and play capability if supported by the system.  
ꢀꢀ On-Screen Display (OSD) adjustments in English, Dutch, French, German, Italian, Japanese,  
and Spanish for ease of setup and screen optimization  
ꢀꢀ Software and documentation CD that includes HP Display Assistant, Pivot Pro software, monitor  
driver software, and product documentation  
ꢀꢀ Energy saver feature to meet requirements for reduced power consumption  
HP LP1965, LP2065, and LP2465 Models  
1
   
AssetControl  
Compliant with the following regulated specifications:  
European Union CE Directives  
Swedish MPR II 1990ꢀꢀ  
Swedish TCO Requirements  
2
Chapter 1 Product Features  
2 Safety and Maintenance Guidelines  
Important Safety Information  
A power cord is included with the monitor. If another cord is used, use only a power source and  
connection appropriate for this monitor. For information on the correct power cord set to use with the  
monitor, refer to the Power Cord Set Requirements section in Appendix C.  
WARNING! To reduce the risk of electric shock or damage to the equipment:  
• Do not disable the power cord grounding feature. The grounding plug is an important safety  
feature.  
• Plug the power cord in a grounded (earth) outlet that is easily accessible at all times.  
• Disconnect power from the product by unplugging the power cord from the electrical outlet.  
For your safety, do not place anything on power cords or cables. Arrange them so that no one  
may accidentally step on or trip over them. Do not pull on a cord or cable. When unplugging  
from the electrical outlet, grasp the cord by the plug.  
To reduce the risk of serious injury, read the Safety and Comfort Guide. It describes proper  
workstation, setup, posture, and health and work habits for computer users, and provides  
important electrical and mechanical safety information. This guide is located on the Web at  
http://www.hp.com/ergo and/or on the documentation CD, if one is included with the monitor.  
CAUTION For the protection of the monitor, as well as the computer, connect all power  
cords for the computer and its peripheral devices (such as a monitor, printer, scanner) to  
some form of surge protection device such as a power strip or Uninterruptible Power Supply  
(UPS). Not all power strips provide surge protection; the power strips must be specifically  
labeled as having this ability. Use a power strip whose manufacturer offers a Damage  
Replacement Policy so you can replace the equipment, if surge protection fails.  
Important Safety Information  
3
   
Maintenance Guidelines  
To enhance the performance and extend the life of the monitor:  
ꢀꢀ Do not open the monitor cabinet or attempt to service this product yourself. Adjust only those  
controls that are covered in the operating instructions. If the monitor is not operating properly or  
has been dropped or damaged, contact an authorized HP dealer, reseller, or service provider.  
ꢀꢀ Use only a power source and connection appropriate for this monitor, as indicated on the label/  
back plate of the monitor.  
ꢀꢀ Be sure the total ampere rating of the products connected to the outlet does not exceed the  
current rating of the electrical outlet, and the total ampere rating of the products connected to  
the cord does not exceed the rating of the cord. Look on the power label to determine the  
ampere rating (AMPS or A) for each device.  
ꢀꢀ Install the monitor near an outlet that you can easily reach. Disconnect the monitor by grasping  
the plug firmly and pulling it from the outlet. Never disconnect the monitor by pulling the cord.  
ꢀꢀ Turn the monitor off when not in use. You can substantially increase the life expectancy of the  
monitor by using a screen saver program and turning off the monitor when not in use.  
ꢀꢀ Slots and openings in the cabinet are provided for ventilation. These openings must not be  
blocked or covered. Never push objects of any kind into cabinet slots or other openings.  
ꢀꢀ Do not drop the monitor or place it on an unstable surface.  
ꢀꢀ Do not allow anything to rest on the power cord. Do not walk on the cord.  
ꢀꢀ Keep the monitor in a well-ventilated area, away from excessive light, heat or moisture.  
ꢀꢀ When removing the monitor base, you must lay the monitor face down on a soft area to prevent  
it from getting scratched, defaced, or broken.  
Cleaning the Monitor  
1.ꢀꢀ Turn off the monitor and the computer.  
2.ꢀꢀ Unplug the monitor from the wall outlet.  
3.ꢀꢀ Clean the monitor plastics with a clean cloth dampened with water.  
4.ꢀꢀ Clean the monitor screen with an antistatic screen cleaner.  
CAUTION Do not use benzene, thinner, ammonia, or any other volatile substances to clean  
the monitor or the screen. These chemicals may damage the cabinet finish as well as the  
screen.  
Shipping the Monitor  
Keep the original packing box in a storage area. You may need it later if you move or ship the monitor.  
4
Chapter 2 Safety and Maintenance Guidelines  
     
3 Setting Up the Monitor  
To set up the monitor, ensure that the power is turned off to the monitor, computer system, and other  
attached devices, then follow the instructions below.  
NOTE Be sure the master power switch, located on the rear panel of the monitor, is in the off  
position. The master power switch turns off all power to the monitor.  
Installing the Monitor Pedestal Baseꢀꢀ  
NOTE Do not install the pedestal base if the monitor will be used on a wall, swing arm, or  
other mounting fixture; instead see the section on Mounting the Monitor in this chapter.  
1. Using both hands, position the monitor over the pedestal base.  
CAUTION Do not touch the surface of the LCD panel. Pressure on the panel may  
cause non-uniformity of color or disorientation of the liquid crystals. If this occurs the  
screen will not recover to its normal condition.  
2. Press down firmly on the monitor to lock the pedestal base in place. When the base locks, it will  
make a clicking sound.  
Figure 3-1 Inserting the Monitor into the Pedestal Base  
NOTE Be sure the pedestal base is securely locked before continuing with the setup.  
Installing the Monitor Pedestal Base  
5
   
Rear Componentsꢀꢀ  
Figure 3-2 Rear Components  
Component  
Function  
1
2
3
4
Cable Lock Provision  
Master Power Switch  
AC Power Connector  
DVI-I Connectors  
Provides slot for use with cable security locks.  
Turns off all power to the monitor.  
Connects the AC power cord to the monitor.  
Connects the DVI-I to VGA signal cable or DVI-D signal  
cable to the monitor.  
5
6
7
USB Upstream  
Connector  
Connects the monitor USB hub to a host USB port/hub.  
Connects optional USB devices to the monitor.  
Connects optional USB devices to the monitor.  
USB Downstream  
Connectors  
USB Downstream  
Connectors (side panel)  
6
Chapter 3 Setting Up the Monitor  
 
Selecting the Signal Connectors and Cables  
The monitor features two DVI-I connectors capable of supporting either analog or digital input.  
The video mode supported by the DVI-I connector is determined by the video cable used.  
ꢀꢀ For digital operation, use the DVI-D signal cable provided. Connect the DVI-D signal cable to a  
DVI-I connector on the monitor and the other end to the DVI connector on the computer.  
ꢀꢀ For analog operation, use the DVI-I to VGA signal cable provided. Connect the DVI-I to VGA  
signal cable to a DVI-I connector on the monitor and the other end to the VGA connector on the  
computer.  
The monitor will automatically determine which inputs have valid video signals. The inputs can be  
selected through the On-Screen Display (OSD) feature by pressing the Input Select button on the  
front panel.  
Figure 3-3 Connecting the DVI-I to VGA Signal Cable  
Figure 3-4 Connecting the DVI-D Signal Cable  
Selecting the Signal Connectors and Cables  
7
 
Connecting the Monitor  
1.ꢀꢀ Place the monitor in a convenient, well-ventilated location near the computer.  
2.ꢀꢀ Connect one end of the USB hub cable to the USB connector on the rear panel of the computer,  
and the other end to the upstream USB connector on the monitor.  
Figure 3-5 Connecting the USB Cable  
WARNING! To reduce the risk of electric shock or damage to the equipment:  
• Do not disable the power cord grounding plug. The grounding plug is an important  
safety feature.  
• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible  
at all times.  
• Disconnect power from the equipment by unplugging the power cord from the electrical  
outlet.  
For your safety, do not place anything on power cords or cables. Arrange them so that no  
one may accidentally step on or trip over them. Do not pull on a cord or cable. When  
unplugging from the electrical outlet, grasp the cord by the plug.  
8
Chapter 3 Setting Up the Monitor  
 
3. Connect one end of the power cable to the AC power connector on the back of the monitor, and  
the other end to an electrical wall outlet.  
Figure 3-6 Connecting the Power Cable  
4. Place the cables through the cable management channel on the back of the monitor base.  
Figure 3-7 Using the Cable Management Feature  
Connecting the Monitor  
9
Adjusting the Monitor  
1. Tilt the monitor's panel forward or backward to set it to a comfortable eye level.  
Figure 3-8 Tilting the Monitor  
NOTE The 24" model has a tilt range of -5 to +25 degrees.  
2. Swivel the monitor to the left or right for the best viewing angle.  
Figure 3-9 Swiveling the Monitor  
10 Chapter 3 Setting Up the Monitor  
 
3. Adjust the monitor's height so that it is parallel to your eye height for a comfortable viewing  
position.  
WARNING! A lock-down/release button on the front of the column prevents the display  
head of the 19" model from sliding up when the monitor is lifted. If the display head is  
locked in the lowest height position:  
a. Make sure that the monitor is safely positioned on a stable surface.  
b. Gently push down on the display head.  
c. While pushing down the display head, press the lock-down/release button on the front  
of the column.  
d. Guide the display head up to the desired height.  
Figure 3-10 Adjusting the Height (LP2065 and LP2465 models)  
NOTE The 19" model has a height adjustment range of 100 mm.  
Adjusting the Monitor 11  
4. Pivot the monitor from landscape to portrait orientation viewing to adapt to your application.  
Figure 3-11 Pivoting the Monitor  
NOTE The 20" model (shown above) pivots counter-clockwise; the 19" and 24" models  
pivot clockwise.  
To view information on the screen in portrait mode, you will need to install the Pivot Pro  
software included on the software and documentation CD.  
Turning on the Monitor  
1. Press the power switch to turn on the computer.  
2. Press the master power switch on the rear of the monitor.  
3. Press the power button on the front of the monitor.  
CAUTION Burn-in image damage may occur on monitors that display the same static image  
on screen for a prolonged period of time.* To avoid burn-in image damage on the monitor  
screen, you should always activate a screen saver application or turn off the monitor when it is  
not in use for a prolonged period of time. Image retention is a condition that may occur on all  
LCD screens.  
* A prolonged period of time is 12 consecutive hours of non-use.  
12 Chapter 3 Setting Up the Monitor  
 
Connecting USB Devices  
The monitor provides four USB connectors, two on the side panel and two on the rear panel, used to  
connect devices such as a digital camera, USB keyboard, or USB mouse.  
NOTE You must connect the USB hub cable from the monitor to the computer to enable the  
USB 2.0 ports on the monitor. Refer to Step 2 in Connecting the Monitor.  
Figure 3-12 Connecting USB Devices  
Connecting USB Devices 13  
 
Using the Accessory Rails  
The monitor features accessory rails on the rear that may be used to mount optional devices, such  
as the HP speaker bar, to attach to the LCD. Refer to the documentation included with the optional  
device for detailed mounting instructions.  
Figure 3-13 Using the Accessory Rails Feature  
Removing the Monitor Pedestal Base  
You can remove the monitor panel from the pedestal base to mount the panel on a wall, a swing  
arm, or other mounting fixture.  
This monitor has a Quick Release mechanism that allows you to easily remove and replace the  
monitor panel to the pedestal base.  
CAUTION Before beginning to disassemble the monitor, be sure the monitor is turned off  
and the power and signal cables are both disconnected. If the monitor has a connected audio  
cable, disconnect it.  
1. Disconnect and remove the signal and power cables from the back of the monitor.  
2. Slide the quick release latch (1) on the pedestal base to the side (either right or left).  
14 Chapter 3 Setting Up the Monitor  
   
3. Pull up on the monitor display head (2) to remove it from the base.  
Figure 3-14 Removing the Monitor from the Pedestal Base  
Mounting the Monitor  
The HP Quick Release can be removed from the pedestal base and installed to a mounting fixture. It  
allows you to quickly and securely attach the monitor panel to the mounting fixture.  
Base steps in the previous section.  
CAUTION This monitor supports the VESA industry standard 100 mm mounting holes.  
To attach a third-party mounting solution to the monitor, four 4 mm, 0.7 pitch, and 10 mm  
long screws are required (not provided with the monitor). Longer screws should not be  
used because they may damage the monitor. It is important to verify that the  
manufacturer’s mounting solution is compliant with the VESA standard and is rated to  
support the weight of the monitor display panel. For best performance, it is important to  
use the power and video cables provided with the monitor.  
2. Remove the Quick Release from the pedestal base by removing the four screws.  
Figure 3-15 Removing the HP Quick Release from the Pedestal Base  
Removing the Monitor Pedestal Base 15  
 
3. Mount the Quick Release to a swing arm or other mounting fixture using the four screws  
removed from the Quick Release in the previous step.  
Figure 3-16 Installing the Quick Release  
CAUTION The Quick Release can also be installed directly to a wall to mount the  
monitor panel. It is designed to support a maximum of up to 24 lbs. (10.9 kg). If you are  
mounting to a wall, HP recommends that you consult with a qualified engineering,  
architectural, or construction professional to determine the appropriate type and quantity  
of mounting fasteners required for your application and to ensure that the mounting  
solution is properly installed to support applied loads.  
4. Insert the monitor panel into the Quick Release, and then press down firmly on the monitor to  
lock it in place. When the Quick Release locks, it will make a clicking sound.  
Figure 3-17 Inserting the Monitor Panel into the Quick Release  
16 Chapter 3 Setting Up the Monitor  
Locating the Rating Labelsꢀꢀ  
The rating labels on the monitor provide the spare part number, product number, and serial number.  
You may need these numbers when contacting HP about the monitor model. The rating labels are  
located on the rear panel of the monitor display head.  
Figure 3-18 Locating the Rating Labels  
Locating the Rating Labels 17  
 
18 Chapter 3 Setting Up the Monitor  
4 Operating the Monitor  
Software and Utilities  
The CD that comes with the monitor contains files you can install on the computer:  
an .INF (Information) file  
an .ICM (Image Color Matching) file  
auto-adjustment pattern utility  
additional software for the monitor modelꢀꢀ  
Adobe Reader is supplied on this CD and can be installed from the menu.ꢀꢀ  
NOTE If the monitor does not include a CD, the .INF and .ICM files can be downloaded from  
the HP monitors support Web site. See Downloading from the Worldwide Web in this chapter.  
The Information File  
The .INF file defines monitor resources used by Microsoft Windows operating systems to ensure  
monitor compatibility with the computer’s graphics adapter.  
This monitor is Microsoft Windows Plug and Play compatible and the monitor will work correctly  
without installing the .INF file. Monitor Plug and Play compatibility requires that the computer’s  
graphic card is VESA DDC2–compliant and that the monitor connects directly to the graphics card.  
Plug and Play does not work through separate BNC type connectors or through distribution buffers/  
boxes.  
The Image Color Matching File  
The .ICM files are data files that are used in conjunction with graphics programs to provide  
consistent color matching from monitor screen to printer, or from scanner to monitor screen.  
The .ICM file contains a monitor color system profile. This file is activated from within graphics  
programs that support this feature.  
NOTE The ICM color profile is written in accordance with the International Color Consortium  
(ICC) Profile Format specification.  
Software and Utilities 19  
       
Installing the .INF and .ICM Files  
After you determine that you need to update, you can install the .INF and .ICM files from the CD or  
download them.  
Installing from the CD  
To install the .INF and .ICM files on the computer from the CD:  
1. Insert the CD in the computer CD-ROM drive. The CD menu is displayed.  
2. View the Monitor Driver Software Readme file.  
3. Select Install Monitor Driver Software.  
4. Follow the on-screen instructions.  
5. After the software has been installed, restart Windows.  
6. Ensure that the proper resolution and refresh rates appear in the Windows Display control panel.  
NOTE You may need to install the digitally signed monitor .INF and .ICM files manually from  
the CD in the event of an installation error. Refer to the Monitor Driver Software Readme file  
on the CD.  
Downloading from the Worldwide Web  
To download the latest version of .INF and .ICM files from the HP monitors support Web site:  
1. Refer to http://www.hp.com/support and select the country region.  
2. Follow the links for the monitor to the support page and download page.  
3. Ensure the system meets the requirements.  
4. Download the software by following the instructions.  
20 Chapter 4 Operating the Monitor  
     
Using the Auto-Adjustment Function  
You can optimize the screen performance for the VGA (analog) input by using the -/Auto button on  
the monitor and the auto-adjustment pattern software utility on the CD provided.  
Do not use this procedure if the monitor is using a DVI input. If the monitor is using a VGA (analog)  
input, this procedure can correct the following image quality conditions:  
ꢀꢀ Fuzzy or unclear focus  
ꢀꢀ Ghosting, streaking or shadowing effects  
ꢀꢀ Faint vertical bars  
ꢀꢀ Thin, horizontal scrolling lines  
An off-center pictureꢀꢀ  
To use the auto-adjustment feature:ꢀꢀ  
1.ꢀꢀ Allow the monitor to warm up for 20 minutes before adjusting.  
2.ꢀꢀ Press the -/Auto button on the monitor front panel.  
ꢀꢀ You can also press the Menu/Select button, then select Auto-Adjustment from the OSD  
Main Menu. Refer to Adjusting the Monitor Settings in this chapter.  
ꢀꢀ If the result is not satisfactory, continue with the procedure.  
3.ꢀꢀ Insert the CD in the disc drive. The CD menu is displayed.  
4.ꢀꢀ Select Open Auto-Adjustment Software . The setup test pattern is displayed.  
5.ꢀꢀ Press the -/Auto button on the monitor front panel to produce a stable, centered image.  
6.ꢀꢀ Press the ESC key or any other key on the keyboard to exit the test pattern.  
Using the Auto-Adjustment Function 21  
 
Front Panel Controls  
Table 4-1 Monitor Front Panel Controls  
Controlꢀꢀ  
Function  
1
2
Menu/Select  
Opens, selects or exits the OSD menu.  
(Minus)/Auto  
ꢀꢀ Navigates backward through the OSD menu and  
decreases adjustment levels.  
ꢀꢀ When the OSD menu is inactive, activates the auto  
adjustment feature to optimize the screen image.  
3
+ (Plus)  
Navigates forward through the OSD menu and increases  
adjustment levels.  
4
5
Input Select  
Power LED  
Selects the video input (DVI-I #1 or DVI-I #2).  
Fully powered = Green.  
Sleep mode = Amber.  
Sleep Timer mode = Flashing Amber.  
Turns the monitor on or off.  
6
Power  
22 Chapter 4 Operating the Monitor  
 
Adjusting the Monitor Settings  
The monitor settings can be adjusted from the On-Screen Display (OSD) menu or from the HP  
Display Assistant utility.  
Using the On-Screen Display Menu  
Use the On-Screen Display (OSD) to adjust the screen image based on your viewing preferences.  
To access the OSD, do the following:  
1.ꢀꢀ If the monitor is not already on, press the Power button to turn on the monitor.  
2.ꢀꢀ To access the OSD Menu, press the Menu/Select button on the monitor’s front panel.  
3.ꢀꢀ To navigate through the OSD Menu, press the + (Plus) button on the monitor’s front panel to  
scroll up, or the (Minus)/Auto button to scroll in reverse.  
4.ꢀꢀ To select an item from the OSD Menu, use the + or buttons to scroll to and highlight your  
selection, then press the Menu/Select button to select that function.  
5.ꢀꢀ Adjust the item using the + or buttons on the front panel to adjust the scale.  
6.ꢀꢀ After adjusting the function, select Save and Return, or Cancel if you don’t want to save the  
setting, then select Exit from the Main Menu.  
NOTE If the buttons remain untouched for 10 seconds while displaying a menu, new  
adjustments will be discarded and the settings will revert to previous settings and exit the  
menu.  
Adjusting the Monitor Settings 23  
   
OSD Menu Selections  
The following table lists the On-Screen Display (OSD) menu selections and their functional  
descriptions. After changing an OSD menu item, and if the menu screen has these options, you may  
choose to:  
ꢀꢀ Cancel—to return to the previous menu level.  
ꢀꢀ Save and Return—to save all changes and return to the OSD Main Menu screen. This Save  
and Return option is only active if you change a menu item.  
Reset—to change back to the previous setting.ꢀꢀ  
Table 4-2 OSD Menuꢀꢀ  
Icon  
Main Menu  
Submenu  
Description  
Brightness  
Adjusts the brightness level of the screen. The factory default  
range is 50 or 90, depending on the model.  
Contrast  
Adjustable scale  
Adjusts the contrast level of the screen. The factory default  
range is 80.  
Image Control  
Adjusts the screen image.  
Auto Adjustment  
Horizontal Position  
Vertical Position  
Automatically adjusts the screen image.  
Adjusts the position of the screen image left and right.  
Adjusts the position of the screen image up and down.  
Custom Scaling (not  
available on LP1965  
model)  
Selects the method on how displayed information on the  
monitor will be formatted. Select:  
ꢀꢀ Fill to Screen—image fills the entire screen and may look  
distorted or elongated because of non-proportional scaling  
of height and width  
ꢀꢀ Fill to Aspect Ratio—image is sized to fit the screen and  
maintains proportional image  
ꢀꢀ One-to-one—disables video scaling, displays an image  
that is smaller in size than the monitor’s capability and  
centers the image on the screen in the active viewing area  
Sharpness (not  
available on LP1965  
model)  
Adjusts the screen image to look sharper or soft.  
NOTE If the one-to-one custom scaling menu is  
selected, scaling is disabled and the sharpness feature  
will also be disabled.  
Clock  
Minimizes any vertical bars or strips visible on the screen  
background. Adjusting the Clock will also change the horizontal  
screen image.  
Clock Phase  
Adjusts the focus of the display. This adjustment allows you to  
remove any horizontal noise and clear or sharpen the image of  
characters.  
Color  
Selects the screen color. The factory default is 6500K or  
Custom Color, depending on the model.  
24ꢀꢀ Chapter 4 Operating the Monitor  
 
Table 4-2 OSD Menu (continued)  
Icon  
Main Menu  
Submenu  
9300 K  
Description  
Changes to slightly blueish white.  
Changes to slightly reddish white.  
Selects and adjusts your own color scales:  
6500 K  
Custom Color  
R—sets your own red color levels  
G—sets your own green color levels  
B—sets your own blue color levels  
sRGB  
Sets your screen colors to adapt to the color standards used in  
the image technology industry.  
Language  
Selects the language in which the OSD menu is displayed. The  
factory default is English.  
Management  
Selects the power management features of the monitor.  
Enables the power saving feature. Select:  
Power Saver  
On  
Off  
The factory default is On.  
Power On Recall  
Restores power to the monitor following an unexpected removal  
of power. Select:  
On  
Off  
The factory default is On.  
Mode Display  
Displays the resolution, refresh rate and frequency information  
on the screen each time the OSD Main Menu is accessed.  
Select:  
On  
Off  
The factory default is On or Off, depending on the model.  
Power-On Status  
Display  
Displays the operating status of the monitor each time the  
monitor is powered on. Select the location to display the status  
to:  
Top  
Middle  
Bottom  
Off  
The factory default is On or Off, depending on the model.  
Adjusting the Monitor Settings 25  
Table 4-2 OSD Menu (continued)  
Icon  
Main Menu  
Submenu  
Description  
DDC/CI Support  
Allows the computer to control some OSD menu features such  
as brightness, contrast and color temperature. Set to:  
On  
Off  
The factory default is On.  
Sleep Timer  
Provides the timer adjustment menu options:  
ꢀꢀ Set Current Time—sets the current time in hours and  
minutes  
ꢀꢀ Set Sleep Time—sets the time you want to place the  
monitor in sleep mode  
ꢀꢀ Set on Time—sets the time you want the monitor to wake  
up from sleep mode  
ꢀꢀ Timer—sets the Sleep Timer feature On or Off. The default  
setting is Off  
ꢀꢀ Sleep Now—immediately sets the monitor to enter sleep  
mode  
OSD Controlꢀꢀ  
Adjusts the position of the OSD menu on the screen.  
Horizontal Position  
Vertical Position  
OSD Timeout  
Changes the viewing position of the OSD menu to the left or  
right area of the screen. The factory default range is 50.  
Changes the viewing position of the OSD menu to the top or  
bottom area of the screen. The factory default range is 50.  
Sets the time duration in seconds that the OSD is visible after  
the last button is pressed. The factory default is 30 seconds.  
OSD Transparency  
Adjust to view the background information through the OSD.  
Selects and displays important information about the monitor.  
Provides the current input video mode.  
Informationꢀꢀ  
Current Settings  
Recommended Settings Provides the recommended resolution mode and refresh rate  
for the monitor.  
Serial Number  
Reports the serial number of the monitor. The serial number is  
needed if contacting HP technical support.  
Version  
Reports the firmware version of the monitor.  
Reports the total hours of backlight operation.  
Backlight hours  
Video Input  
Control  
Selects the default or primary video input signal when the  
monitor is connected to two active and valid video sources. The  
monitor will automatically determine the video format. The  
default input selection is DVI.  
DVI-I#1  
DVI–I#2  
Selects DVI-I 1 input. This input accepts either analog or digital  
signals.  
Selects DVI-I 2 input. This input accepts either analog or digital  
signals.  
26 Chapter 4 Operating the Monitor  
Table 4-2 OSD Menu (continued)  
Icon  
Main Menu  
Submenu  
Description  
Disable Input Auto-  
Switching  
Keeps the monitor's video input selection at it's current setting.  
This menu selection is visible if the video input control is set to  
Enable Input Auto-switching.  
Enable Input Auto-  
Switching  
Automatically returns the monitor's video input to the default  
auto-switching mode. This menu selection is visible if the video  
input control is set to Disable Input Auto-switching.  
Factory Reset  
Returns all OSD menu settings and Power-On Status Display  
(for LP2465 model) settings to the factory default setting,  
except the Language and Power-On Status Display (for LP1965  
and LP2065 models) settings.  
Exit  
Exits the OSD menu screen.  
Adjusting the Monitor Settings 27  
Optimizing Digital Conversion  
This monitor contains advanced circuitry that allows the flat panel screen to function like a standard  
monitor. Two controls in the on-screen display can be adjusted to improve image performance: Clock  
and Clock Phase.  
NOTE The Clock and Clock Phase controls are adjustable only when using an analog input.  
These controls are not adjustable for digital inputs.  
The Clock must first be set correctly since the Clock Phase settings are dependent on the  
main Clock setting. Use these controls only when the auto-adjustment function does not  
provide a satisfactory image.  
ꢀꢀ Clock—Increases/decreases the value to minimize any vertical bars or stripes visible on the  
screen background.  
ꢀꢀ Clock Phase—Increases/decreases the value to minimize video distortion or video jitter.  
NOTE When using the controls, you will obtain the best results by using the auto-adjustment  
pattern software utility provided on the CD.  
When adjusting the Clock and Clock Phase values, if the monitor images become distorted,  
continue adjusting the values until the distortion disappears. To restore the factory settings,  
select Yes from the Factory Reset menu in the on-screen display.  
Using the HP Display Assistant Utility  
HP Display Assistant, included on the software and documentation CD, is a software utility that  
guides you through the tuning process with easy to understand instructions and background patterns  
designed for each monitor control. It provides:  
ꢀꢀ Accurate screen calibration through the use of step-by-step instruction Wizards to obtain the  
best overall image quality.  
ꢀꢀ Software control of the monitor image and color settings to eliminate dependence on the  
monitor’s front panel buttons and On-Screen Display (OSD) menu.  
ꢀꢀ Defined preset display settings for each individual user in a multi-user environment.  
ꢀꢀ Multiple preset display settings for a single user based on content and ambient lighting.  
ꢀꢀ Asset Management and Power Management capabilities that include remote control for  
individual or a group of displays on the domain from a centralized console application.  
The HP Display Assistant Utility has two modes of operation: Wizard and OSD mode. The preferred  
method of use is Wizard mode, which takes you through a step-by-step process to accurately  
calibrate the monitor. This method relies on a sequence of steps that will obtain the best display  
results when completed.  
NOTE Refer to the HP Display Assistant user guide for additional information about the  
software.  
28ꢀꢀ Chapter 4 Operating the Monitor  
   
Identifying Monitor Conditions  
Special messages will appear on the monitor screen when identifying the following monitor conditions:  
ꢀꢀ Input Signal Out of Range—Change resolution setting to 1280 × 1024 – 60Hz (LP1965 19"  
model), 1600 × 1200 - 60Hz (LP2065 20" model), or 1920 × 1200 - 60 Hz (LP2465 24" model)—  
Indicates the monitor does not support the input signal because the resolution and/or refresh  
rate are set higher than the monitor supports.  
ꢀꢀ No Input Signal—Indicates the monitor is not receiving a video signal from the PC on the  
monitor video input connector. Check to determine if the PC or input signal source is off or in the  
power saving mode.  
ꢀꢀ Multiple Inputs are ActiveUse the OSD to select the desired video input—Indicates the  
monitor is connected to two video inputs. The monitor is trying to display both inputs, but after  
10 seconds the monitor uses the default signal input.  
ꢀꢀ Auto Adjustment is in Progress—Indicates the auto-adjustment function is active.  
ꢀꢀ Monitor Going to Sleep—Indicates the screen display is entering a sleep mode.  
ꢀꢀ Check Video Cable—Indicates the video cable is not properly connected to the computer.  
ꢀꢀ OSD Lock—The OSD can be enabled or disabled by pressing and holding the Menu button on  
the front panel for 10 seconds. If the OSD is locked, the warning message OSD Lock-Out  
displays for ten seconds.  
ꢀꢀ If the OSD is locked, press and hold the Menu button for 10 seconds to unlock the OSD.  
ꢀꢀ If the OSD is unlocked, press and hold the Menu button for 10 seconds to lock the OSD.  
Sleep Timer Mode  
The Sleep Timer mode is an energy-saving feature that enables you to set a time for the monitor to  
power on and off at the same time every day. This also extends the life of the backlight bulbs in the  
monitor. The Sleep Timer has five settings:  
ꢀꢀ Set Current Time  
ꢀꢀ Set Sleep Time  
ꢀꢀ Set On Time  
ꢀꢀ Timer: On/Off  
Sleep Nowꢀꢀ  
To set the timer:ꢀꢀ  
1.ꢀꢀ Press the Menu button on the monitor front panel to display the Advanced Menu.  
2.ꢀꢀ Scroll down and highlight Management.  
3.ꢀꢀ Press the Menu button to select Management.  
4.ꢀꢀ Scroll down and highlight and select Sleep Timer > Set Current Time.  
Identifying Monitor Conditions 29  
   
NOTE You must set the current local time before you reset the time for Sleep Time orꢀꢀ  
On Time. Note that the time is displayed in a 24–hour clock format. For example, 1:15ꢀꢀ  
p.m. is displayed as 13 hours 15 minutes.  
5.ꢀꢀ Press the Menu button once to enter the adjustment mode for hours.  
6.ꢀꢀ Press the - (Minus) or + (Plus) button to adjust the hour.  
7.ꢀꢀ Press the Menu button again to enter the time for minutes.  
8.ꢀꢀ Press the - (Minus) or + (Plus) button to adjust the minutes.  
9.ꢀꢀ Press the Menu button to lock in the time chosen.  
10.ꢀꢀ After setting the current time, the highlight automatically skips to Set Sleep Time hours. Repeat  
steps 6 through 9 to set Sleep Time.  
11.ꢀꢀ If you do not want to set Sleep Time, press the Menu button twice, then select Save and  
Return to exit the menu.  
12.ꢀꢀ After setting Sleep Time, the highlight automatically skips to Set On Time hours. Repeat steps  
6 through 9 to set On Time.  
13.ꢀꢀ Set the Timer mode to On to activate the Sleep Timer settings.  
14.ꢀꢀ When you are finished, select Save and Return to exit the menu.  
The fifth selection, Sleep Now, turns the monitor backlights off immediately and stays in sleep mode  
until the next On Time activates or a monitor button is pressed.  
HP Display LiteSaver  
HP Display LiteSaver is a software application, available on the CD, that increases monitor life and  
saves energy. It allows you to place the monitor into its low power sleep mode at predefined times by  
shutting down or reducing power to most internal circuits. This helps protect the LCD panel against  
image retention. Image retention can occur when the monitor is left on while displaying the same  
image for an extended period of time, leaving a shadow of the image on the screen.  
Installing the HP Display LiteSaver Software  
1.ꢀꢀ Insert the CD in the computer CD-ROM Drive. The CD menu is displayed.  
2.ꢀꢀ Select Install HP Display LiteSaver Software.  
3.ꢀꢀ After installing the software, click the HP Display LiteSaver icon in the Windows system tray or  
right-click the icon and select Configure from the pop-up menu.  
4. Select the following options to configure the HP Display LiteSaver features:ꢀꢀ  
Table 4-3 HP Display LiteSaver Configuration Optionsꢀꢀ  
Select This Option  
To Do This  
Enable Display LiteSaver  
Enables the HP Display LiteSaver functions; deselect to disable the HP Display  
LiteSaver.  
30ꢀꢀ Chapter 4 Operating the Monitor  
   
Table 4-3 HP Display LiteSaver Configuration Options (continued)  
Select This Option  
To Do This  
Display Off  
Sets the time when the monitor automatically turns off. This does not affect  
screen saver operation, which has priority over the HP Display LiteSaver.  
Display On  
Sets the time when the monitor automatically turns on. This does not affect  
screen saver operation, which has priority over the HP Display LiteSaver.  
Activity Extension  
Sets the time in minutes before the monitor turns off if there is any keyboard or  
mouse activity after the Display Off time is reached. If the keyboard or mouse is  
used, then HP Display LiteSaver waits until the set amount of time before turning  
the display off again. Set to 0 to disable. If disabled, the monitor will turn off as  
soon as the Display Off time is reached, regardless of keyboard or mouse activity.  
Show 1 minute Display Off Notice  
Displays a popup message in the system tray 1 minute before the monitor is  
turned off by HP Display LiteSaver.  
Status  
OK  
Shows the time until the monitor is next due to be turned off by HP Display  
LiteSaver.  
Stores the current settings and minimizes HP Display LiteSaver to the System  
Tray.  
Cancel  
Restores the previous settings and minimizes HP Display LiteSaver to the  
System Tray. HP Display LiteSaver will continue to run.  
Help  
Exit  
Opens the online help file.  
Exits and closes the HP Display LiteSaver. It will no longer control the monitor  
power until it is next run.  
View HP Display LiteSaver Readme on the CD for additional information on how to configure HP  
Display LiteSaver.  
sRGB Support  
The monitor is designed to support sRGB for color management, which adapts to the color standards  
used in the image technology industry.  
To take advantage of the sRGB support, you will need to change the monitor’s color temperature to  
sRGB and install the sRGB color profile (ICM) file.  
NOTE The sRGB color temperature preset will improve the color accuracy of sRGB images  
on the computer monitor, but some color variation may still occur.  
Changing the Color Temperature  
1. Press the Menu button on the front panel of the monitor to launch the Main Menu of the OSD.  
2. Select Advanced Menu to access all options in the Main Menu.  
3. Select Color to display the Color Temperature menu.  
4. Select sRGB.  
5. Select Save and Return to exit the menu.  
sRGB Support 31  
   
Installing the sRGB ICM File for Microsoft Windows 2000 and Windows XPꢀꢀ  
NOTE To complete the following procedure, you must be logged in as an administrator or a  
member of the administrator’s group. If the computer is connected to a network, network  
policy settings may prevent you from completing this procedure. The sRGB ICM file does not  
support Windows 95 and Windows NT operating systems.  
1.ꢀꢀ Click the Display icon in the Control Panel.  
2.ꢀꢀ In the Display Properties windows, select the Settings tab, then click the Advanced button.  
3.ꢀꢀ Select the Color Management tab, then click the Add button to open the Add Profile  
Association dialog box.  
4.ꢀꢀ Select the sRGB Color Space Profile.icm file, then click the Add button  
5.ꢀꢀ To activate a color profile for the monitor, you must set it as the Default Monitor Profile. Select  
sRGB Color Space Profile, then click Set as Default button.  
6.ꢀꢀ Click Apply or OK.  
32ꢀꢀ Chapter 4 Operating the Monitor  
 
A Troubleshooting  
Solving Common Problems  
The following table lists possible problems, the possible cause of each problem, and the  
recommended solutions.  
Problem  
Possible Cause  
Solution  
Screen is blank.  
Power cord is disconnected.  
Connect the power cord.  
Power switch on front panel of the Press the front panel power button.  
monitor is turned off.  
Master power switch on rear panel Turn the master power switch to On.  
of the monitor is turned Off.  
Video cable is improperly  
connected.  
Connect the video cable properly. Refer to Chapter 3,  
Setting Up the Monitor for more information.  
Screen blanking is active.  
Press any key on the keyboard or move the mouse to  
inactivate the screen blanking utility.  
Image appears blurred,  
indistinct, or too dark.  
Brightness and contrast are too  
low.  
Press the —/Auto button on the front panel. If this does  
not correct the image, press the Menu button to open the  
Basic OSD Menu, and adjust the brightness and contrast  
scales as needed.  
Image is not centered  
Position may need adjustment.  
Press the Menu button to access the OSD menu. Select  
Image Control/Horizontal Position or Vertical Position to  
adjust the horizontal or vertical position of the image.  
Check Video Cable is  
displayed on screen.  
Monitor video cable is  
disconnected.  
Connect the DVI-D signal cable to the DVI-I connector  
on the computer, or the VGA to DVI-I cable to the DVI-I  
connector on the computer. Be sure that the computer  
power is off while connecting the video cable.  
Out of Range. Set  
Video resolution and/or refresh  
rate are set higher than what the  
monitor supports.  
Restart the computer and enter Safe Mode. Change the  
settings to a supported setting (see Table B-4 LP1965  
Model Factory Preset Modes). Restart the computer so  
that the new settings take effect.  
Monitor to 1280 × 1024  
@ 60Hz is displayed on  
screen. (LP1965 19" model)  
Out of Range. Set  
Video resolution and/or refresh  
rate are set higher than what the  
monitor supports.  
Restart the computer and enter Safe Mode. Change the  
settings to a supported setting (see Table B-5 LP2065  
Model Factory Preset Modes). Restart the computer so  
that the new settings take effect.  
Monitor to 1600 × 1200  
@ 60Hz is displayed on  
screen. (LP2065 20" model)  
Out of Range. Set  
Video resolution and/or refresh  
rate are set higher than what the  
monitor supports.  
Restart the computer and enter Safe Mode. Change the  
settings to a supported setting (see Table B-6 LP2465  
Model Factory Preset Modes). Restart the computer so  
that the new settings take effect.  
Monitor to 1920 × 1200  
@ 60Hz is displayed on  
screen. (LP2465 24" model)  
Solving Common Problems 33  
   
Problem  
Possible Cause  
Solution  
HP Display LiteSaver  
doesn't turn off the monitor not elapsed.  
screen.  
The Activity Extension time has  
The default Activity Extension value is set to 10 minutes.  
The HP Display LiteSaver will wait to detect no input or  
movement from the keyboard or mouse for 10  
consecutive minutes after the Display Off time has  
passed, before the monitor enters into low-power mode.  
For example, if the Display Off time is set to 5 minutes  
from the current time and the Activity Extension is set to  
10 minutes, the HP Display LiteSaver will not actually  
turn off the display until 10 minutes of inactivity has  
elapsed, even though the Display Off time is 5 minutes  
from now.  
The HP Display LiteSaver may not Confirm that the HP Display LiteSaver is compatible with  
be compatible with the computer  
system. Some notebook  
computers are not compatible and  
the monitor power can not be  
controlled.  
the system.  
1.ꢀꢀ Right-click on the HP Display LiteSaver icon in the  
system tray.  
2.ꢀꢀ Select Power Off Display from the menu.  
The monitor screen should turn off if the system is  
compatible. To turn the monitor back on, wait 5 seconds  
and move the mouse.  
NOTE If the monitor did not turn off, then the  
computer graphics driver is not compatible with  
the HP Display LiteSaver software.  
The monitor is off but it did The monitor's power saving  
Check the monitor's OSD menu setting for power saving  
enable/disable controls. The control should be set to  
enable to allow the monitor to enter into low-power  
modes.  
not seem to enter into a  
low-power sleep mode.  
control is disabled.  
Using the Worldwide Web  
For the online access to technical support information, self-solve tools, online assistance, community  
forums of IT experts, broad mutlivendor knowledge base, monitoring and diagnostic tools, go to  
Preparing to Call Technical Support  
If you cannot solve a problem using the trouble shooting tips in this section, you may need to call  
technical support. Have the following information available when you call:  
The monitor  
Monitor model number  
Serial number for the monitor  
Purchase date on invoice  
Conditions under which the problem occurred  
Error messages received  
34 Appendix A Troubleshooting  
   
Hardware configuration  
Hardware and software you are using  
Preparing to Call Technical Support 35ꢀꢀ  
36 Appendix A Troubleshooting  
B Technical Specificationsꢀꢀ  
NOTE All performance specifications are provided by the component manufacturers.  
Performance specifications represent the highest specification of all HP's component  
manufacturers' typical level specifications for performance and actual performance may vary  
either higher or lower.  
LP1965 Model  
Table B-1 LP1965 Model Specifications  
Display  
19 inches  
TFT LCD  
48.3 cm  
48.3 cm  
Type  
Viewable Image Size  
19–inch diagonal  
-5 to 30°  
Tilt  
Swivel  
-45 to 45°  
17.2 lbs.  
Maximum Weight (Unpacked)  
7.8 kg  
Dimensions (include base)  
14.85 inches  
8.78 inches  
15.90 inches  
377.16 mm  
223.00 mm  
403.90 mm  
Height  
Depth  
Width  
Maximum Graphic Resolution  
1280 × 1024 (75 Hz) analog input  
1280 × 1024 (75 Hz) digital input  
720 × 400  
Text Mode  
Dot Pitch  
0.294 (H) × 0.294 (W) mm  
24 to 83 kHz  
Horizontal Frequency  
Vertical Refresh Rate  
Environmental Requirements Temperature  
48 to 76 Hz  
41 to 95° F  
-4 to 140° F  
20 to 80%  
5 to 35° C  
Operating Temperature  
Storage Temperature  
Relative Humidity  
-20 to +60° C  
LP1965 Model 37  
   
Table B-1 LP1965 Model Specifications (continued)  
Power Source  
Altitude:  
100 — 240 VAC, 50/60 Hz  
0 to 12,000 feet  
0 to 40,000 feet  
0 to 3657.6 m  
0 to 12192 m  
Operating  
Storage  
Power Consumption (maximum)  
Input Terminal  
<55 watts  
Two DVI-I connectors with cables included.  
LP2065 Model  
Table B-2 LP2065 Model Specifications  
Display  
20.1 inches  
TFT LCD  
51 cm  
51 cm  
Type  
Viewable Image Size  
20–inch diagonal  
-5 to 30°  
Tilt  
Swivel  
-45 to 45°  
Maximum Weight (Unpacked)  
20.3 lbs.  
9.2 kg  
Dimensions (include base)  
16.7 inches  
8.7 inches  
17.4 inches  
425.0 mm  
220.0 mm  
443.0 mm  
Height  
Depth  
Width  
Maximum Graphic Resolution  
1600 × 1200 (75 Hz) analog input  
1600 × 1200 (60 Hz) digital input  
720 × 400  
Text Mode  
Dot Pitch  
0.258 (H) × 0.258 (W) mm  
30 to 94 kHz  
Horizontal Frequency  
Vertical Refresh Rate  
Environmental Requirements Temperature  
48 to 85 Hz  
41 to 95° F  
5 to 35° C  
Operating Temperature  
Storage Temperature  
Relative Humidity  
Power Source  
Altitude:  
-4 to 140° F  
-20 to +60° C  
20 to 80%  
100 — 240 VAC, 50/60 Hz  
0 to 12,000 feet  
0 to 40,000 feet  
0 to 3657.6 m  
0 to 12192 m  
Operating  
Storage  
38 Appendix B Technical Specifications  
 
Table B-2 LP2065 Model Specifications (continued)  
Power Consumption (maximum)  
Input Terminal  
<75 watts  
Two DVI-I connectors with cables included.  
LP2465 Model  
Table B-3 LP2465 Model Specifications  
Display  
24.1 inches  
TFT LCD  
61 cm  
61 cm  
Type  
Viewable Image Size  
24–inch diagonal  
-5 to 25°  
Tilt  
Swivel  
-45 to 45°  
23.4 lbs.  
Maximum Weight (Unpacked)  
10.6 kg  
Dimensions (include base)  
17.3 inches  
9.1 inches  
22.0 inches  
440.0 mm  
232.0 mm  
558.4 mm  
Height  
Depth  
Width  
Maximum Graphic Resolution  
1920 × 1200 (60Hz) analog input  
1920 × 1200 (60Hz) digital input  
720 × 400  
Text Mode  
Dot Pitch  
0.270 (H) × 0.270 (W) mm  
30 to 94 kHz  
Horizontal Frequency  
Vertical Refresh Rate  
Environmental Requirements Temperature  
48 to 85 Hz  
41 to 95° F  
5 to 35° C  
Operating Temperature  
Storage Temperature  
Relative Humidity  
Power Source  
-4 to 140° F  
-20 to +60° C  
20 to 80%  
100 — 240 VAC, 50–60 Hz  
Altitude:  
0 to 12,000 feet  
0 to 40,000 feet  
0 to 3657.6 m  
0 to 12192 m  
Operating  
Storage  
Power Consumption (maximum)  
Input Terminal  
<110 watts  
Two DVI-I connectors with cables included.  
LP2465 Model 39  
 
Recognizing Preset Display Resolutions  
The display resolutions listed below are the most commonly used modes and are set as factory  
defaults. This monitor automatically recognized these preset modes and they will appear properly  
sized and centered on the screen.  
Table B-4 LP1965 Model Factory Preset Modes  
Preset  
Pixel Format  
640 × 480  
640 × 480  
640 × 480  
720 × 400  
800 × 600  
800 × 600  
800 × 600  
832 × 624  
1024 × 768  
1024 × 768  
1024 × 768  
1152 × 870  
1152 × 900  
1280 × 1024  
1280 × 1024  
Horz Freq (kHz)  
31.5  
Vert Freq (Hz)  
60.0  
1
2
37.9  
73.0  
3
37.5  
75.0  
4
31.5  
70.0  
5
37.9  
60.0  
6
48.1  
72.0  
7
46.9  
75.0  
8
49.7  
75.0  
9
48.4  
60.0  
10  
11  
12  
13  
14  
15  
56.5  
70.0  
60.0  
75.0  
68.7  
75.0  
71.7  
76.0  
64.0  
60.0  
80.0  
75.0  
Table B-5 LP2065 Model Factory Preset Modes  
Preset  
Pixel Format  
640 × 480  
640 × 480  
640 × 480  
720 × 400  
800 × 600  
800 × 600  
832 × 624  
1024 × 768  
1024 × 768  
1024 × 768  
Horz Freq (kHz)  
31.5  
Vert Freq (Hz)  
59.9  
1
2
37.5  
75.0  
3
43.3  
85.0  
4
31.5  
70.1  
5
37.9  
60.3  
6
53.7  
85.1  
7
49.7  
74.6  
8
48.4  
60.0  
9
60.0  
75.0  
10  
68.7  
85.0  
40 Appendix B Technical Specifications  
     
Table B-5 LP2065 Model Factory Preset Modes (continued)  
11  
1152 × 870  
1152 × 900  
1280 × 960  
1280 × 1024  
1280 × 1024  
1280 × 1024  
1600 × 1200  
1600 × 1200  
68.7  
61.8  
60.0  
64.0  
80.0  
91.2  
75.0  
93.8  
75.1  
66.0  
60.0  
60.0  
75.0  
85.0  
60.0  
75.0  
12  
13  
14  
15  
16  
17  
*18  
* For analog inputs only.  
Table B-6 LP2465 Model Factory Preset Modes  
Preset  
1
Pixel Format  
640 × 480  
Horz Freq (kHz)  
31.5  
Vert Freq (Hz)  
59.9  
2
640 × 480  
37.5  
75.0  
3
720 × 400  
31.5  
70.1  
4
800 × 624  
37.9  
60.3  
5
800 × 600  
46.9  
75.0  
6
832 × 624  
49.7  
74.6  
7
1024 × 768  
1024 × 768  
1024 × 768  
1152 × 720  
1152 × 870  
1152 × 900  
1280 × 768  
1280 × 960  
1280 × 1024  
1280 × 1024  
1280 × 1024  
1600 × 1200  
1600 × 1200  
1600 × 1200  
1680 × 1050  
1920 × 108  
48.4  
60.0  
8
60.0  
75.0  
9
68.7  
85.0  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
*20  
21  
22  
44.9  
60.0  
68.7  
75.1  
61.8  
66.0  
47.4  
60.0  
60.0  
60.0  
64.0  
60.0  
80.0  
75.0  
91.2  
85.0  
61.7  
60.0  
75.0  
60.0  
93.8  
75.0  
65.3  
60.1  
67.2  
60.0  
Recognizing Preset Display Resolutions 41  
 
Table B-6 LP2465 Model Factory Preset Modes (continued)  
23  
1920 × 1200  
1920 × 1200  
74.0  
74.6  
60.0  
60.0  
*24  
*For analog inputs only.  
Entering User Modes  
The video controller signal may occasionally call for a mode that is not preset if:  
You are not using a standard graphics adapter.  
You are not using a preset mode.  
It this occurs, you may need to readjust the parameters of the monitor screen by using the on-screen  
display. Your changes can be made to any or all of these modes and saved in memory. The monitor  
automatically stores the new setting, then recognized the new mode just as it does a preset mode. In  
addition to the 15 factory preset modes for the LP1965 model, the 18 factory present modes for the  
LP2065 model, and the 24 factory preset modes for the LP2465 model, there are four user modes  
that can be entered and stored.  
Energy Saver Feature  
When the monitor is in its normal operating mode, the monitor uses less than 37 watts (LP1965  
model) of power or 55 watts of power (LP2065 and LP2465 models) and the Power light is green.  
The monitor also supports a reduced power state. The reduced power state will be entered into if the  
monitor detects the absence of either the horizontal sync signal and/or the vertical sync signal. Upon  
detecting the absence of these signals, the monitor screen is blanked, the backlight is turned off, and  
the power light is turned amber. When the monitor is in the reduced power state, the monitor will  
utilize less than 2 watts of power. There is a brief warm up period before the monitor will return to its  
normal operating mode.  
Refer to the computer manual for instructions on setting energy saver features (sometimes called  
power management features).  
NOTE The above power saver feature only works when connected to computers that have  
energy saver features.  
By selecting the settings in the monitor's Energy Saver utility, you can also program the monitor to  
enter into the reduced poser state at a predetermined time. When the monitor's Energy Saver utility  
causes the monitor to enter the reduced power state, the power light blinks amber.  
42 Appendix B Technical Specifications  
   
C Agency Regulatory Noticesꢀꢀ  
Federal Communications Commission Notice  
This equipment has been tested and found to comply with the limits for a Class B digital device,  
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection  
against harmful interference in a residential installation. This equipment generates, uses, and can  
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may  
cause harmful interference to radio communications. However, there is no guarantee that  
interference will not occur in a particular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be determined by turning the equipment off  
and on, the user is encouraged to try to correct the interference by one or more of the following  
measures:  
ꢀꢀ Reorient or relocate the receiving antenna.  
ꢀꢀ Increase the separation between the equipment and the receiver.  
ꢀꢀ Connect the equipment into an outlet on a circuit different from that to which the receiver is  
connected.  
ꢀꢀ Consult the dealer or an experienced radio or television technician for help.  
Modifications  
The FCC requires the user to be notified that any changes or modifications made to this device that  
are not expressly approved by Hewlett Packard Company may void the user's authority to operate  
the equipment.  
Cables  
Connections to this device must be made with shielded cables with metallic RFI/EMI connector  
hoods to maintain compliance with FCC Rules and Regulations.  
Declaration of Conformity for Products Marked with the  
FCC Logo (United States Only)  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two  
conditions:  
1.ꢀꢀ This device may not cause harmful interference.  
2.ꢀꢀ This device must accept any interference received, including interference that may cause  
undesired operation.  
Federal Communications Commission Notice 43  
         
For questions regarding the product, contact:ꢀꢀ  
Hewlett Packard Companyꢀꢀ  
P. O. Box 692000, Mail Stop 530113ꢀꢀ  
Houston, Texas 77269-2000ꢀꢀ  
Or, call 1-800-HP-INVENT (1-800 474-6836)ꢀꢀ  
For questions regarding this FCC declaration, contact:ꢀꢀ  
Hewlett Packard Companyꢀꢀ  
P. O. Box 692000, Mail Stop 510101  
Houston, Texas 77269-2000  
Or, call (281) 514-3333  
To identify this product, refer to the Part, Series, or Model number found on the product.  
Canadian Notice  
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing  
Equipment Regulations.  
Avis Canadien  
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel  
brouilleur du Canada.  
European Union Regulatory Notice  
This product complies with the following EU Directives:  
Low Voltage Directive 73/23/EEC  
EMC Directive 89/336/EEC  
Compliance with these directives implies conformity to applicable harmonized European standards  
(European Norms) which are listed on the EU Declaration of Conformity issued by Hewlett-Packard  
for this product or product family.  
This compliance is indicated by the following conformity marking placed on the product:  
This marking is valid for non-Telecom  
This marking is valide for EU non-  
products and EU harmonized Telecom harmonized Telecom products.  
products (e.g. Bluetooth)  
44 Appendix C Agency Regulatory Notices  
     
*Notified body number (used only if  
applicable — refer to the product label).  
German Ergonomics Notice  
HP products which bear the “GS” approval mark, when forming part of a system comprising HP  
brand computers, keyboards and monitors that bear the “GS” approval mark, meet the applicable  
ergonomic requirements. The installation guides included with the products provide configuration  
information.  
Japanese Notice  
Korean Noticeꢀꢀ  
Power Cord Set Requirements  
The monitor power supply is provided with Automatic Line Switching (ALS). This feature allows the  
monitor to operate on input voltages between 100–120V or 200–240V.  
The power cord set (flexible cord or wall plug) received with the monitor meets the requirements for  
use in the country where you purchased the equipment.  
If you need to obtain a power cord for a different country, you should purchase a power cord that is  
approved for use in that country.  
The power cord must be rated for the product and for the voltage and current marked on the  
product's electrical ratings label. The voltage and current rating of the cord should be greater than  
the voltage and current rating marked on the product. In addition, the cross-sectional area of the wire  
must be a minimum of 0.75 mm² or 18 AWG, and the length of the cord must be between 6 feet (1.8  
m) and 12 feet (3.6 m). If you have questions about the type of power cord to use, contact an  
authorized HP service provider.  
A power cord should be routed so that it is not likely to be walked on or pinched by items placed  
upon it or against it. Particular attention should be paid to the plug, electrical outlet, and the point  
where the cord exits from the product.  
German Ergonomics Notice 45  
       
Japanese Power Cord Requirements  
For use in Japan, use only the power cord received with this product.  
CAUTION Do not use the power cord received with this product on any other products.  
Product Environmental Notices  
Materials Disposal  
This HP product contains mercury in the fluorescent lamp in the display LCD that might require  
special handling at end-of-life.  
Disposal of this material can be regulated because of environmental considerations. For disposal or  
recycling information, contact the local authorities or the Electronic Industries Alliance (EIA)  
Disposal of Waste Equipment by Users in Private Household in the  
European Union  
This symbol on the product or on its packaging indicates that this product must not be disposed of  
with your household waste. Instead, it is your responsibility to dispose of your waste equipment by  
handing it over to a designated collection point for the recycling or waste electrical and electronic  
equipment. The separate collection and recycling of your waste equipment at the time of disposal will  
help to conserve natural resources and ensure that it is recycled in a manner that protects human  
health and the environment. For more information about where you can drop off your waste  
equipment for recycling, please contact the local city office, the household waste disposal service or  
the shop where you purchased the product.  
Restriction of Hazardous Substances (RoHS)  
A Japanese regulatory requirement, defined by specification JIS C 0950, 2005, mandates that  
manufacturers provide Material Content Declarations for certain categories of electronic products  
offered for sale after July 1, 2006. To view the JIS C 0950 material declaration for this product, visit  
46 Appendix C Agency Regulatory Notices  
         
D LCD Monitor Quality and Pixel Policyꢀꢀ  
The TFT monitor uses high-precision technology, manufactured according to HP standards, to  
guarantee trouble-free performance. Nevertheless, the display may have cosmetic imperfections that  
appear as small bright or dark spots. This is common to all LCD displays used in products supplied  
by all vendors and is not specific to the HP LCD. These imperfections are caused by one or more  
defective pixels or sub-pixels.  
ꢀꢀ A pixel consists of one red, one green, and one blue sub-pixel.  
ꢀꢀ A defective whole pixel is always turned on (a bright spot on a dark background), or it is always  
off (a dark spot on a bright background). The first is the more visible of the two.  
ꢀꢀ A defective sub-pixel (dot defect) is less visible than a defective whole pixel and is small and  
only visible on a specific background.  
The HP display does not have more than:  
ꢀꢀ 3 bright dots.  
ꢀꢀ 5 dark dots.  
ꢀꢀ 5 total bright and dark dots.  
ꢀꢀ No more than two adjacent (less than 2.5 mm edge-to-edge) defective pixels.  
To locate defective pixels, the monitor should be viewed under normal operating conditions, in  
normal operating mode at a supported resolution and refresh rate, from a distance of approximately  
50 cm (20 in).  
HP expects that, over time, the industry will continue to improve its ability to produce LCDs with  
fewer cosmetic imperfections and HP will adjust guidelines as improvements are made.  
47  
 
48 Appendix D LCD Monitor Quality and Pixel Policy  

GE Profile JP938 User Manual
GE 27909 User Manual
Electrolux EN 64 TM User Manual
Eizo EIZO RadiForce GS320 CL User Manual
Dell Computer Monitor IN2020F User Manual
BenQ FP91G User Manual
Autodesk XW8400 User Manual
AT T KX TG5423 User Manual
AT T E2520 User Manual
APW HSO 200 User Manual