HP Hewlett Packard Compaq WF1907 User Manual

Users Guide  
vp15 LCD Monitor  
vp17 LCD Monitor  
vp19 LCD Monitor  
FP1707 LCD Monitor  
WF1907 LCD Monitor  
w1907 LCD Monitor  
w2007 LCD Monitor  
w2207 LCD Monitor  
Notational Conventions  
The following section describes notational conventions used in this document.  
Notes, Cautions, and Warnings  
Throughout this guide, blocks of text may be accompanied by an icon. These blocks are notes, cautions, and  
warnings, and they are used as follows:  
ÅWARNING: Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life.  
CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss  
of information.  
Ä
Text set off in this manner indicates additional information.  
User’s Guide  
iii  
   
iv  
User’s Guide  
Contents  
User’s Guide  
v
vi  
User’s Guide  
1
Product Features  
HP LCD Monitors  
The HP LCD (liquid crystal display) monitors have an active matrix, thin-film transistor (TFT) screen. This guide  
discusses the following models:  
vp15 LCD Monitor  
vp17 LCD Monitor  
vp19 LCD Monitor  
FP1707 LCD Monitor  
WF1907 LCD Monitor  
w1907 LCD Monitor  
w2007 LCD Monitor  
w2207 LCD Monitor  
Features  
Large, diagonal viewable-area display  
Optimum resolution, plus full-screen support for lower resolutions:  
vp15: 1024 × 768 @ 60 Hz  
vp17, vp19, and FP1707: 1280 × 1024 @ 60 Hz  
WF1907 and w1907: 1440 × 900 @ 60 Hz  
w2007 and w2207: 1680 x 1050 @ 60 Hz  
Video inputs supported:  
VGA analog signal  
DVI digital signal (select models only)  
Fast response time, providing better experience for gaming and graphics  
Easy viewing from a sitting or standing position, or while moving from one side of the monitor to the other  
Tilt adjustment  
Height adjustment (select models only)  
Pivot adjustment, for landscape or portrait viewing (select models only)  
Removable pedestal and Video Electronics Standards Association (VESA) standard mounting holes for flexible  
mounting solutions, including wall-mounting  
Security lock slot for a Kensington lock security cable (security cable sold separately)  
Plug and Play capability, if supported by your computer system  
On-screen display (OSD) adjustments for ease of setup and screen optimization (choose English, Simplified  
Chinese, French, German, Italian, Spanish, Dutch, or Japanese)  
Swiveling monitor, allowing a usable range of motion (select models only)  
Built-in stereo speakers, front- or rear-facing depending on model  
Two Universal Serial Bus (USB) 2.0 ports to use with two USB devices (select models only)  
Keyboard parking (select models only)  
User’s Guide  
1–1  
     
Product Features  
Power Saver to reduce energy consumption  
Quick View settings display  
CD includes (select models only):  
Drivers (select models only)  
Auto-adjustment software  
My Display software (select models only)  
Documents  
®
®
Adobe Acrobat Reader  
Varied monitor base designs  
Cantilever base  
Double-hinged base  
Column base  
1–2  
User’s Guide  
2
Safety and Maintenance Guidelines  
Important Safety Information  
The power cord is designed for use with your monitor. To use a different cord, use only a power source and  
connection compatible with this monitor.  
WARNING: To reduce the risk of electric shock or damage to your equipment, do not disable the power cord grounding  
Å
Å
feature. The grounding plug is an important safety feature. Connect the equipment to a grounded (earthed) power outlet.  
WARNING: For your safety, be sure that the grounded power outlet you plug the power cord into is easily accessible to the  
operator and located as close to the equipment as possible. To disconnect power from the equipment, unplug the power cord  
from the power outlet by grasping the plug firmly. Never pull on the cord.  
CAUTION: To protect your monitor, as well as your computer, connect all power cords for your computer and its peripheral  
devices (such as a monitor, printer, or scanner) to a surge protection device such as a power strip with surge protection or  
uninterruptible power supply (UPS).  
Ä
Not all power strips provide surge protection; the power strips must be specifically labeled as having this ability. Use a power strip  
whose manufacturer offers a damage replacement policy, so you can replace your equipment if surge protection fails.  
Safety Precautions  
Use only a power source and connection compatible with this monitor, as indicated on the label/back plate of  
the monitor.  
Be sure the total ampere rating of the products connected to the outlet does not exceed the current rating of the  
electrical outlet, and the total ampere rating of the products connected to the power cord does not exceed the  
rating of the power cord. Look on the power label to determine the ampere rating (Amps or A) for each device.  
Install your monitor near a power outlet that you can easily reach. Disconnect the monitor by grasping the plug  
firmly and pulling it from the outlet. Never disconnect the monitor by pulling the cord.  
Do not allow anything to rest on the power cord. Do not walk on the cord.  
Maintenance Guidelines  
To enhance the performance and extend the life of your monitor:  
Do not open your monitor cabinet or attempt to service this product yourself. If your monitor is not operating  
properly or has been dropped or damaged, contact your Hewlett-Packard authorized dealer, reseller, or service  
provider.  
Adjust only those controls that are described in the operating instructions.  
Turn your monitor off when not in use. You can substantially increase the life expectancy of the monitor by using  
a screen saver program and turning off the monitor when not in use.  
Keep your monitor in a well-ventilated area, away from excessive light, heat, or moisture.  
Slots and openings in the cabinet are provided for ventilation. These openings must not be blocked or covered.  
Never push objects of any kind into cabinet slots or other openings.  
Unplug the monitor from the power outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.  
Do not drop the monitor or place it on an unstable surface.  
When removing the monitor base, you must lay the monitor face down on a soft area to prevent it from getting  
scratched, defaced, or broken.  
User’s Guide  
2–1  
       
Safety and Maintenance Guidelines  
Cleaning the Monitor  
The monitor is a high-quality optical device that requires special care when cleaning. To clean the monitor, follow  
these steps:  
1. Turn off the computer and the monitor.  
2. Unplug your monitor from the power outlet before cleaning.  
CAUTION: Do not use benzene, thinner, ammonia, or any volatile substance to clean the monitor screen or cabinet. These  
chemicals may damage the monitor. Do not use liquid or aerosol cleaners. Never use water to clean an LCD screen.  
Ä
3. Wipe the screen with a dry, soft, clean cloth.  
If the screen requires additional cleaning, use an antistatic screen cleaner.  
4. Dust the monitor housing. Use a damp cloth to clean the cabinet.  
If the cabinet requires additional cleaning, use a clean cloth dampened with isopropyl alcohol.  
5. Plug in the monitor.  
6. Turn on the monitor and the computer.  
2–2  
User’s Guide  
 
3
Preparing the Monitor for Shipping  
Keep the original packing box in a storage area. You may need it later if you move or ship your monitor.  
You may need to detach the monitor base when you ship the HP LCD monitor.  
Removing the Monitor Base  
WARNING: Do not remove the base from the pedestal while the monitor is standing in the upright position. Attempting to  
remove the base from the pedestal while the monitor is upright might injure the user.  
Å
WARNING: Before disassembling or folding the monitor, turn off the monitor power, and disconnect all power, video, and  
Å
audio cables. To disconnect power from the equipment, unplug the power cord from the power outlet by grasping the power  
cord firmly. Never pull on the cord.  
CAUTION: The screen is fragile. Placing the monitor screen down on a flat, soft area prevents scratches, defacing, or  
breakage. Avoid applying pressure to the LCD screen; doing so can cause damage.  
Ä
Removing the cantilever base  
1. Disconnect the power, video, and audio cables from the monitor.  
2. Set the monitor screen down on a flat, soft, protected surface.  
3. Detach the base from the monitor 1,2.  
Removing the cantilever base  
User’s Guide  
3–1  
       
Preparing the Monitor for Shipping  
4. Fold the monitor neck down, and place the monitor and base in the original packing box.  
Removing the column base  
1. Disconnect the power, video, and audio cables from the monitor.  
2. Set the monitor screen down on a flat, soft, protected surface.  
3. Pinch and hold the tabs with one hand; then pull the base off with the other hand to detach the base from the  
monitor.  
Removing the column base  
ÅWARNING: Be careful to avoid pinching or scraping your fingers when removing the base.  
4. Put the monitor and base in the original packing box.  
3–2  
User’s Guide  
 
Preparing the Monitor for Shipping  
Folding the Double-Hinged Monitor  
You don’t have to remove this monitor base. Fold the double-hinged monitor in its original shipping position  
to ship.  
WARNING: Do not place the double-hinged monitor face down for folding. The base hinge can spring up and  
cause serious damage to the user.  
Å
1. Turn the monitor to a horizontal position with no tilt.  
2. Lower the monitor all the way until the hinge is flat.  
The monitor screen should still be vertical to the desktop so you can access the hinge.  
3. Place the shipping strap around the base, pull it tight, and connect it by sliding the strap ends through  
the slips.  
User’s Guide  
3–3  
 
Preparing the Monitor for Shipping  
4. Fold the monitor screen down flat, horizontal to the desktop.  
5. Pivot the monitor to the portrait position.  
6. Place the folded monitor, screen-side up, in its original shipping box.  
3–4  
User’s Guide  
4
Setting Up the Monitor  
Unpacking the Monitor  
1. Unpack the monitor. Make sure all contents are included. Store the packing box.  
2. Turn off the computer and other attached devices.  
3. Determine whether the monitor will be desktop-mounted or wall-mounted. See “Installing the Monitor.”  
4. Prepare a flat area to assemble the monitor. You may need a flat, soft, protected area for placing the monitor  
screen-down while preparing it for installation.  
5. You need a Phillips screwdriver for preparing the monitor for wall-mounting. You may need a straight-slot  
screwdriver to secure some cables.  
Installing the Monitor  
You can install the monitor on a desktop or wall-mount it. Place the monitor in a convenient, well-ventilated location  
near your computer.  
If the monitor will be installed on a:  
Connect the monitor cables after you have installed the montior.  
Installing the HP LCD Monitor on a Desktop  
Follow the instructions for your monitor type.  
Unfolding the double-hinged monitor  
WARNING: Do not place the double-hinged monitor face down when you first take it out of the box. The hinge can spring  
up and cause serious damage.  
Å
1. Set the monitor screen-side up on a flat surface.  
User’s Guide  
4–1  
           
Setting Up the Monitor  
2. Rotate the screen to the horizontal position.  
3. Holding the base of the monitor, lift up the panel at its top without touching or putting pressure on the  
screen 3.  
4. Remove the shipping strap (do not cut it) 4.  
Put the shipping strap in a safe place, in case you need it to ship the monitor.  
5. Lift and lower the base hinge for proper viewing.  
4–2  
User’s Guide  
Setting Up the Monitor  
Assembling the cantilever base  
CAUTION: The screen is fragile. Avoid touching or applying pressure to the LCD screen; doing so can cause  
damage.  
Ä
1. Set the monitor screen down on a flat, soft, protected surface.  
2. Align the neck with the monitor base.  
3. Slide the base until it snaps in place. Make sure the base is securely locked in place.  
Attaching the cantilever base  
4. Lift the monitor to an upright position and place on a flat, stable surface.  
Assembling the column base  
1. Set the monitor base on a flat, stable surface.  
2. Lift the monitor, and align the pedestal with the base.  
3. Lower the monitor until the base snaps in place. Make sure the base is securely locked.  
Attaching the column base  
User’s Guide  
4–3  
   
Setting Up the Monitor  
Wall-Mounting the Monitor (Mounting Fixture not Supplied)  
Before you mount the monitor on a wall, a swing arm, or other mounting fixture, you must remove the  
monitor base and the pedestal. You will need a Phillips screwdriver. Read the following warning and  
caution statements before beginning the procedure.  
WARNING: To reduce the risk of personal injury or of damage to the equipment, check that the wall-mounting  
fixture is adequately installed and secured before attaching the monitor. Refer to the instructions supplied with the  
wall-mounting fixture and check that it is capable of supporting the monitor.  
Å
Preparing the double-hinged monitor for wall-mounting  
WARNING: Do not place the double-hinged monitor face down with the shipping strap intact. The hinge can  
spring up and cause serious damage.  
Å
1. Disconnect the power cable and any other cables from the monitor.  
2. Carefully place the monitor face down on a flat, soft surface. This might entail elongating the hinge  
and tilting the monitor back to ensure the monitor is flat.  
3. With your fingertips, snap off the VESA cover from the back of the monitor.  
4. Remove all four screws from the VESA plate.  
5. Save the removed items (cover, screws, and base) for future use.  
6. Follow the instructions included with the mounting fixture to ensure that the monitor is safely attached.  
The four-threaded mounting holes that are on the back of the panel are compliant with the VESA  
standard for mounting flat-panel monitors. The15-inch monitor uses the 75 mm spacing standard,  
while the other models use the 100 mm spacing standard.  
Use the four holes to attach a swing arm or other mounting fixture.  
4–4  
User’s Guide  
   
Setting Up the Monitor  
Preparing the cantilever-base monitor for wall-mounting  
1. Disconnect the power cable and any other cables from the monitor.  
2. Remove the monitor base. Refer to “Removing the Monitor Base” in the previous chapter. Keep the  
monitor panel screen down on a flat, soft area.  
3. After the base is removed, remove the rubber plug on the neck of the monitor. You will see a screw  
below the rubber plug and two additional screws on the panel.  
4. Remove all three screws.  
5. Remove the neck from the monitor.  
6. Save the removed items (rubber plug, screws, neck, and base) for future use.  
7. Follow the instructions included with the mounting fixture to ensure that the monitor is safely attached.  
The four-threaded mounting holes that are on the back of the panel are compliant with the VESA  
standard for mounting flat-panel monitors. The vp15 monitor uses the 75 mm spacing standard, while  
the other models use the 100 mm spacing standard.  
Use the four holes to attach a swing arm or other mounting fixture.  
Preparing the column-base monitor for wall-mounting  
1. Disconnect the power cable and any other cables from the monitor.  
2. With the monitor screen face-down on a flat, soft surface, remove the monitor base. Refer to “Removing  
the Monitor Base” in the previous chapter.  
3. Remove the hinge cover and set it aside. Three screws and the hinge are exposed.  
4. Holding the pedestal so that it cannot fall, remove the single screw that is close to the hinge, and then  
remove the other two screws. If necessary, move the pedestal, so that all three screws are accessible.  
5. Slide the pedestal off the monitor panel.  
6. Save the removed items (screws, hinge cover, pedestal, and base) for future use.  
User’s Guide  
4–5  
   
Setting Up the Monitor  
7. Follow the instructions that are included with the mounting fixture to ensure that the monitor is safely attached.  
The four-threaded mounting holes that are on the back of the panel are compliant with the VESA standard for  
mounting flat-panel monitors. The vp15 monitor uses the 75 mm spacing standard, while the other models use the  
100 mm spacing standard.  
Use the four holes to attach a swing arm or other mounting fixture.  
To reinstall the desktop pedestal and base for the monitor  
1. Remove the mounting fixture.  
2. Reverse the preceding instructions.  
Connecting the VGA (Analog) and/or DVI-D (Digital) Cable  
Use a VGA cable or a DVI-D cable (provided with select models). To use DVI, you must have a DVI-compliant  
graphics card. Connectors are located at the back of the monitor. Be sure the computer and monitor are turned off  
and unplugged.  
VGA  
DVI  
VGA  
DVI  
Connecting the VGA or DVI-D cable—connector locations may vary  
To connect the VGA cable  
Connect one end of the VGA video cable to the back of the monitor and the other end to the VGA video connector  
on the computer.  
To connect the DVI-D cable  
Connect one end of the DVI-D video cable to the back of the monitor and the other end to the DVI video connector on  
the computer. Your computer must have a DVI-compatible graphics card installed for use with this cable. Monitor  
DVI-D connector and cable are included on select models only.  
4–6  
User’s Guide  
       
Setting Up the Monitor  
Connecting the Audio Cable  
Connect the built-in monitor speakers to the computer by using the audio cable, as shown in the following  
illustration.  
Audio In  
Connecting the audio cables—connector locations may vary  
Connecting the USB Hub Cable  
Connect the USB hub cable from the computer to the USB In connector on the monitor. This enables the two  
USB 2.0 ports on the side of the monitor.  
USB In  
Connecting USB Devices to the Monitor  
You can connect two USB devices, such as a USB flash drive or a digital camcorder, to your monitor. You  
can do this only after you have connected the USB hub cable from the computer to the monitor.  
User’s Guide  
4–7  
     
Setting Up the Monitor  
Connecting the Power Cable  
1. Read the warning below.  
ÅWARNING: To reduce the risk of electric shock or damage to your equipment:  
Do not disable the power cord grounding plug. The grounding plug is an important safety feature. Plug the  
power cord into a grounded (earthed) electrical outlet.  
Be sure that the grounded power outlet you plug the power cord is easily accessible to the operator and  
located as close to the equipment as possible. A power cord should be routed so that it is not likely to be  
walked on or pinched by items that are placed upon it or against it.  
Do not place anything on power cords or cables. Arrange them so that no one may accidentally step on or  
trip over them. Do not pull on a cord or cable.  
See “Power Cord Set Requirements” in Appendix B for additional information.  
Connecting the power cable  
2. Connect one end of the power cable to the monitor and the other end to a grounded electrical outlet.  
4–8  
User’s Guide  
 
Setting Up the Monitor  
Cable Management  
The HP LCD monitors have either two hooks or two cable tunnels on either side for cable management. Cables can  
be easily secured and are hidden when viewed from the front.  
ë
User’s Guide  
4–9  
 
Setting Up the Monitor  
Adjusting the Tilt  
For optimal viewing, adjust the screen tilt to your own preference, as follows:  
1. Face the front of the monitor and hold the base so that you do not topple the monitor while changing  
the tilt.  
2. Adjust the tilt by moving the top edge of the monitor either toward or away from you, without touching the  
screen.  
ÄCAUTION: The double-hinged monitor can fall back if the hinge is extended fully and the monitor screen is tilted back too far.  
4–10  
User’s Guide  
 
Setting Up the Monitor  
Adjusting the Swivel (Select Models Only)  
The HP LCD monitor allows a usable range of motion with the swivel feature.  
CAUTION: To avoid breakage or other damage, avoid applying pressure to the LCD screen while swiveling it or changing  
the tilt.  
Ä
Adjusting the Height (Select Models Only)  
The double-hinged monitor adjusts up and down easily by extending or lowering the hinge.  
User’s Guide  
4–11  
   
Setting Up the Monitor  
Pivoting the Monitor (Select Models Only)  
CAUTION: The double-hinged monitor can scratch the base surface if the monitor is not tilted back enough before changing  
the monitor from landscape to portrait position, or from portrait to landscape position.  
Ä
1. Tilt the monitor backward 10 to 30 degrees.  
2. If the monitor is in its landscape position, pivot the monitor clockwise to portrait position.  
3. If the monitor is in its portrait position, pivot it counterclockwise to landscape position.  
4–12  
User’s Guide  
 
Setting Up the Monitor  
Keyboard Parking  
If you need more space on your desktop, you can place specific HP keyboards under the monitor (select models only)  
when not in use.  
User’s Guide  
4–13  
 
Setting Up the Monitor  
4–14  
User’s Guide  
5
Operating the Monitor  
CD Software and Utilities  
The CD that is included with this monitor contains the drivers and software that you can install on your  
computer.  
Installing Drivers  
If you determine that you need to update the drivers, you can install the monitor-driver INF and ICM files from  
the CD (select models only), or download them from the Internet.  
To install the monitor-driver software from the CD:  
1. Insert the CD in your computer CD drive. The CD menu appears.  
2. Select the language.  
3. Click Install Monitor Driver Software.  
4. Follow the onscreen instructions.  
5. Restart the computer.  
6. Ensure that the proper resolutions and refresh rates appear in the Display Control Panel settings. Refer to  
the Windows operating system documentation for more information.  
You might need to install the digitally signed monitor drivers (INF or ICM files) manually from the CD, in case of an  
installation error. Refer to the “Driver Software Readme” file on the CD for instructions (in English only).  
Downloading from the World Wide Web  
To download the latest version of drivers and software files from the HP Support Web site:  
2. Select your country/region.  
3. Select Download Drivers and Software.  
4. Enter the model number of your monitor. The software-download pages for your monitor are displayed.  
5. Download and install the driver and software files by using the instructions in the download pages.  
6. Ensure that your system meets the requirements.  
User’s Guide  
5–1  
         
Operating the Monitor  
Using the Auto-Adjustment Function  
You can easily optimize the screen performance for the VGA input by using the Auto/Select button on the  
monitor and the auto-adjustment pattern software on the CD provided.  
Do not use this procedure if your monitor is using a DVI input (select models only). If your monitor is using  
the VGA input, this procedure can correct the following image-quality conditions:  
Fuzzy or unclear focus  
Ghosting, streaking, or shadowing effects  
Faint vertical bars  
Thin, horizontal scrolling lines  
Off-center picture  
ÄCAUTION: Image retention may occur on monitors that display the same static image on screen for a prolonged  
period of time. To avoid image retention on your monitor screen, you should always use a screen saver  
application or turn off the monitor when it is not in use for a prolonged period of time.  
To use the auto-adjustment feature:  
1. Allow the monitor to warm up for 20 minutes before adjusting.  
2. Press the Auto/Select button on the monitor front panel.  
You can also press the Menu button, and then select Image Control, followed by  
Auto Adjustment from the OSD menu. See “Adjusting Screen Quality” in this chapter.  
If the result is not satisfactory, continue with the procedure.  
3. Insert the CD in your computer CD drive. The CD menu displays.  
4. Select the language.  
5. Select Open Auto-Adjustment Software.  
6. The setup test pattern displays.  
Auto-adjustment setup test pattern  
7. Press the Auto/Select button on the monitor front panel to produce a stable, centered image.  
My Display OSD Software  
Use My Display (available for select models only) to choose preferences for optimum viewing. You can  
select settings for gaming, movies, photo editing or just working on documents and spreadsheets. My  
Display also provides an easy way to adjust settings such as brightness, color, and contrast.  
To install the OSD software:  
1. Insert the CD in your computer CD drive. The CD menu displays.  
2. Select the language.  
3. Click Install My Display Software (available on select models only).  
4. Follow the onscreen instructions.  
5. Restart the computer.  
For additional information, refer to the onscreen Help within the software.  
5–2  
User’s Guide  
   
Operating the Monitor  
Front-Panel Controls  
Control buttons are located on the front of the panel:  
Icon  
Description  
Power  
Turns the monitor on and to standby or sleep mode.  
Menu  
Opens, selects, or exits the OSD menu.  
Adjusts the volume level.  
Opens the Quick View menu to quickly adjust settings for gaming, video, photo, and text.  
Navigates backward through the OSD menu and decreases adjustment levels.  
Navigates forward through the OSD menu and increases adjustment levels.  
Auto-adjusts the display to the ideal setting.  
+
Auto  
Select  
Enters the selected option.  
Using the Onscreen Display (OSD)  
You can use My Display OSD software (select models only) or the front-panel control buttons to adjust settings.  
1. If the monitor is not already on, press the Power button to turn on the monitor.  
2. To access the OSD menu, press the Menu button. The OSD Main Menu displays.  
3. To navigate through the Main or Sub-Menu menu, press the + (Plus) button on the monitor’s front panel  
to scroll up, or the (Minus) button to scroll in reverse. Then press the Auto/Select button to select the  
highlighted function.  
The menu moves to the top if you scroll down at the bottom of the selections. The menu moves to the  
bottom if you scroll up at the top of the selections.  
4. To adjust the scale of a selected item, press the + or button.  
5. Select Save and Return.  
If you don’t want to save the setting, select Cancel from the Sub-Menu or Exit from the  
Main Menu.  
6. Press the Menu button to exit the OSD.  
When a menu is displayed, if the buttons are untouched for 30 seconds (factory default), adjustments and settings are  
saved and the menu closes.  
User’s Guide  
5–3  
   
Operating the Monitor  
OSD Menu Selections  
The following table lists the On-Screen Display (OSD) menu selections and their functional descriptions. After changing an  
OSD menu item, and if the menu screen has these options, you may choose to:  
Cancel — to return to the previous menu level.  
Save and Return — to save all changes and return to the OSD Main Menu screen. This Save and Return option is  
active only if you change a menu item.  
Reset — to change back to the previous setting.  
Main Menu  
Options  
Icon  
Submenu Options  
Description  
Switch Video Input  
(select models only)  
Switches the video input signal source when the monitor is  
connected to two active and valid video sources.  
Brightness  
Contrast  
Adjusts the brightness level of the screen.  
Adjusts the contrast level of the screen.  
Adjusts the screen image.  
Image Control  
Auto-Adjustment  
Automatically adjusts the screen image (VGA Input only).  
Horizontal Position  
Adjusts the horizontal position of the picture (VGA  
Input only).  
Vertical Position  
Clock  
Adjusts the vertical position of the picture (VGA Input only).  
Minimizes any vertical bars or strips visible on the screen  
background. Adjusting the Clock will also change the  
horizontal screen image (VGA Input only).  
Clock Phase  
Adjusts the focus of the display. This adjustment allows you to  
remove any horizontal noise, and clear or sharpen the image  
of characters (VGA Input only).  
Custom Scaling  
(select models only)  
Selects the method on how displayed information on the  
monitor will be formatted. Select:  
Fill to Screen — Image fills the entire screen and might look  
distorted or elongated because of non-proportional scaling of  
height and width.  
Fill to Aspect Ratio — Image is sized to fit the screen and  
maintains proportional image.  
Color  
Selects the screen color. The factory default is 6500 K or  
Custom Color, depending on the model.  
9300 K  
Changes to slightly blueish white.  
Changes to slightly reddish white.  
6500 K  
Custom Color  
Selects and adjusts your own color scales:  
R — Sets your own red color levels.  
G — Sets your own green color levels.  
B — Sets your own blue color levels.  
sRGB  
Sets your screen colors to adapt to the color standards used  
in the image technology industry.  
5–4  
User’s Guide  
 
Operating the Monitor  
Main Menu  
Options  
Icon  
Submenu Options  
Description (Continued)  
Selects viewing mode.  
Selects the movie mode.  
Selects the photo mode.  
Selects the gaming mode.  
Selects the text mode.  
Quick View  
Movie  
Photo  
Gaming  
Text  
Custom  
Settings saved when user adjusts the Brightness, Contrast, or  
Color in one of the Quick View options.  
Language  
Selects the language in which the OSD menu is displayed.  
The factory default is English.  
Management  
Selects the power-management features of the monitor.  
Volume  
Adjusts the volume level.  
OSD Control  
Adjusts the position of the OSD menu on the screen.  
Horizontal OSD Position — Changes the viewing  
position of the OSD menu to the left or right area of  
the screen. The factory default range is 50.  
Vertical OSD Position — Changes the viewing  
position of the OSD menu to the top or bottom area of  
the screen. The factory default range is 50.  
OSD Transparency — Adjust to view the background  
information through the OSD.  
OSD Timeout — Sets the time in seconds that the  
OSD is visible after the last button is pressed. The  
factory default is 30 seconds.  
Power Saver  
Enables the power saving feature. Select:  
On  
Off  
The factory default is On.  
Mode Display  
Displays the resolution, refresh rate, and frequency  
information on the screen each time the OSD Main Menu is  
accessed. Select:  
On  
Off  
The factory default is On or Off, depending on the model.  
Power-On Status Display Displays the operating status of the monitor each time the  
monitor is powered on. Select the location to which to  
display the status:  
Top  
Middle  
Bottom  
Off  
The factory default is Top or Off, depending on the model.  
User’s Guide  
5–5  
Operating the Monitor  
Main Menu  
Options  
Icon  
Submenu Options  
Description (Continued)  
DDC/CI Support  
Allows the computer to control some OSD menu features such  
as brightness, contrast, and color temperature. Set to:  
On  
Off  
The factory default is On.  
Bezel Power LED  
(select models only)  
Turns the light (LED) in the power button On and Off. When  
set to Off, the light will remain off at all times.  
Sleep Timer  
Provides the timer-adjustment menu options:  
Set Current Time — Sets the current time in hours and  
minutes.  
Set Sleep Time — Sets the time you want to place the monitor  
in sleep mode.  
Set on Time — Sets the time you want the monitor to wake up  
from sleep mode.  
Timer — Sets the Sleep Timer feature On or Off; the default  
setting is Off.  
Sleep Now — Immediately sets the monitor to enter  
sleep mode.  
Default Video Input  
Selects the default video input signal when the monitor is  
connected to two active and valid video sources. The default  
is DVI. You must restart the computer to have the change take  
effect.  
Information  
Selects and displays important information about the monitor.  
Provides the current input video mode.  
Current Settings  
Recommended Settings  
Provides the recommended resolution mode and refresh rate  
for the monitor.  
Serial Number  
Reports the serial number of the monitor. The serial number is  
needed if contacting HP technical support.  
Version  
Reports the firmware version of the monitor.  
Reports the total hours of backlight operation.  
Backlight Hours  
Service Support  
For service support, go to:  
Factory Reset  
Returns settings to factory defaults.  
5–6  
User’s Guide  
Operating the Monitor  
Selecting the Video Input Connectors  
The two input connectors are:  
VGA connector (analog)  
DVI-D connector (digital) for select models  
The monitor automatically determines which inputs have valid video signals, and displays the image.  
You can connect the VGA cable, the DVI-D cable, or both. If both cables are installed, the default input selection is  
DVI. The source of input can be switched using the Switch Video Input option in the OSD menu.  
Identifying Monitor Conditions  
Special messages appear on the monitor screen for the following monitor conditions:  
Input Signal Out of Range — Indicates the monitor does not support the video input signal because the  
resolution or refresh rate are set higher than the monitor supports.  
Set the resolution and refresh rate to the value displayed. Restart your computer for the new settings to take effect.  
Monitor Going to Sleep — Indicates the screen display is entering a sleep mode. The speakers are turned off  
in sleep mode.  
Check Video Cable — Indicates a video input cable is not properly connected to the computer or monitor.  
OSD Lock-out — The OSD can be enabled or disabled by pressing and holding the Menu button on the front  
panel for 10 seconds. If the OSD is locked, the warning message “OSD Lock-out” appears for 10 seconds.  
If the OSD is locked, press and hold the Menu button for 10 seconds to unlock the OSD.  
If the OSD is unlocked, press and hold the Menu button for 10 seconds to lock the OSD.  
No Input Signal — Indicates the monitor is not receiving a video signal from the computer on the monitor  
video input connector(s). Check to see if the computer or input signal source is off or in the power-saver mode.  
Auto Adjustment in Progress — Indicates the auto-adjustment function is active. See “Adjusting Screen  
Quality” in this chapter.  
Adjusting Screen Quality  
The auto-adjustment feature automatically fine-tunes the image quality for display size, position, clock, and phase  
each time a new video mode is displayed. For more precise adjustments of VGA input, run the Auto-Adjustment  
software on the CD. See “Using the Auto-Adjustment Function” in this chapter.  
If you want additional image-quality improvement, use the Clock and Clock Phase controls of the monitor to fine-tune  
the image. See “Optimizing Analog Video” in this chapter.  
Optimizing Analog Video  
This monitor contains advanced circuitry that allows the monitor to function as a standard analog monitor. Two  
controls in the OSD menu can be adjusted to improve analog image performance:  
Clock — Increase or decrease the value to minimize any vertical bars or stripes visible on the screen  
background.  
Clock Phase — Increase or decrease the value to minimize video distortion or video jitter.  
Use these controls only when the auto-adjustment function does not provide a satisfactory monitor image in  
analog mode.  
To obtain the best results:  
1. Allow the monitor to warm up for 20 minutes before adjusting.  
2. Display the adjustment-pattern application provided on the CD.  
3. Access the OSD menu, then select Image Control.  
4. Set the main Clock settings correctly first, because the Clock Phase settings depend on the main Clock setting.  
When adjusting the Clock and Clock Phase values, if the monitor images become distorted, continue  
adjusting the values until the distortion disappears.  
To restore the factory settings, access the OSD menu, select Factory Reset, and then select Yes.  
User’s Guide  
5–7  
       
Operating the Monitor  
Power-Saver Feature  
When the monitor is in normal operating mode, the Power light is blue and the monitor uses the normal watts of  
The monitor also supports a power-saver mode that is controlled by the computer. When the monitor is in the  
reduced-power state, the monitor screen is blank, the backlight is off, and the Power light is amber. The monitor uses  
minimum power. When the monitor is “awakened,” a brief warm-up period occurs before the monitor returns to  
normal operating mode. The energy-saving reduced power state activates if the monitor does not detect either the  
horizontal sync signal or the vertical sync signal. The power-saver feature must be activated on your computer for this  
feature to work.  
Refer to your computer documentation for instructions on setting energy-saver features (sometimes called  
power-management features).  
The energy-saver feature works only when the monitor is connected to computers that have energy-saver features.  
High-Bandwidth Digital Content Protection (HDCP)  
If your monitor supports HDCP, it can receive high-definition content. High-definition content is available in many  
sources, such as HD-DVD and Blu-Ray devices or HDTV air or cable broadcasts. If you do not have an HDCP-enabled  
monitor, you may see a black screen or a lower resolution picture when playing high-definition protected content.  
Your computer graphic card and monitor must both support HDCP to display protected content.  
5–8  
User’s Guide  
   
A
Troubleshooting  
Solving Common Problems  
The following table lists possible problems, the possible cause of each problem, and the recommended solutions:  
Problem  
Solution  
Power LED is not on.  
Make sure the Power button is on, and the power cord is properly connected to a grounded  
power outlet and to the monitor.  
Check if Bezel Power LED option in the OSD menu is set to Off and, if so, set to On mode.  
Screen is blank.  
Connect the power cord. Turn on the power.  
Connect the video cable properly. See “Setting Up the Monitor” for more information.  
Press a key on the keyboard or move the mouse to turn off the screen-blanking utility.  
Screen is black or displaying Check if your monitor and computer support HDCP.  
at a lower resolution while  
displaying high-definition  
(HD) content.  
Refer to “High-bandwidth Digital Content Protection (HDCP)” or  
http://www.hp.com/support for more information.  
Image appears blurred,  
indistinct, or too dark.  
Press the Auto/Select button on the monitor front panel. If this does not correct the image, press  
the Menu button to open the OSD menu, and adjust the brightness and contrast scales as  
needed.  
Image is not centered.  
Press the Menu button to access the OSD menu. Select Image Control, and then select  
Horizontal Position or Vertical Position to adjust the horizontal or vertical position of the  
image.  
“Check Video Cable”  
appears on screen.  
Connect the monitor VGA signal cable to the VGA connector on the computer, or connect the  
DVI-D signal cable to the DVI connector on the computer. Be sure that the computer power is off  
while connecting the video cable.  
“Input Signal Out of Range”  
appears on screen.  
Restart your computer and enter Safe Mode. Change your settings to a supported setting (see  
the table in “Preset Video Modes” in Appendix B). Restart your computer, so that the new  
settings take effect.  
Picture is fuzzy and has  
ghosting, shadowing  
problem.  
Adjust the contrast and brightness controls.  
Make sure that you are not using an extension cable or switch box. We recommend plugging  
the monitor directly into the graphic card output connector on the back of your computer.  
For VGA input, the auto-adjustment feature might fix this problem.  
Unable to set the monitor to  
the optimal resolution.  
Make sure that the graphics card supports the optimal resolution.  
Make sure that the latest supported driver is installed for the graphics card. For HP and  
Compaq systems, you can download the latest graphics driver for your system from:  
For other systems, refer to the Web site for your graphics card.  
User’s Guide  
A–1  
   
Troubleshooting  
Problem  
Solution (Continued)  
No Plug and Play.  
In order for the Plug and Play feature of the monitor to work, you need a computer and graphic  
card that are compatible with Plug and Play. Check with your computer manufacturer.  
Check the monitor’s video cable, and make sure that none of the pins are bent.  
Make sure that the HP monitor drivers are installed. Refer to “Installing Drivers” for more  
information. HP monitor drivers are also available at: http://www.hp.com/support  
Picture bounces, flickers, or  
wave pattern is present in  
the picture.  
Move electrical devices that may cause electrical interference as far away from the monitor as  
possible.  
Use the maximum refresh rate that your monitor is capable of at the resolution that you are  
using.  
Monitor is always in “Sleep  
Mode (Amber LED).”  
The computer power switch should be in the On position.  
The computer graphic card should be snugly seated in its slot.  
Check that the monitor video cable is properly connected to the computer.  
Inspect the monitor video cable, and make sure that none of the pins are bent.  
Check that your computer is operational: Press the Caps Lock key and observe the Caps Lock  
LED found on most keyboards. The LED should either turn on or off after hitting the Caps  
Lock key.  
USB 2.0 ports are not  
working.  
Make sure the USB hub cable is securely connected to the monitor and the computer.  
Using the World Wide Web  
Before you contact customer service, refer to HP Technical Support at: http://www.hp.com/support  
Select your country/region, and then follow the links to the support page for your monitor.  
Preparing to Call Technical Support  
If you cannot solve a problem by using the troubleshooting tips in this section, you might have to call technical  
support. For technical support contact information, refer to the printed documentation included with the monitor. Have  
the following information available when you call:  
Monitor model number (located on label on back of monitor)  
Monitor serial number (located on label on back of monitor or in the OSD display in the Information menu)  
Purchase date on invoice  
Conditions under which the problem occurred  
Error messages received  
Hardware configuration  
Name and version of hardware and software you are using  
Locating the Rating Label  
The rating label on the monitor provides the product number and serial number. You may need these numbers when  
contacting HP about your monitor model.  
The rating label is on the back of the monitor.  
A–2  
User’s Guide  
     
B
Technical Specifications  
All specifications represent the typical specifications provided by HP’s component manufacturers; actual  
performance may vary either higher or lower.  
HP LCD Monitors  
Specifications  
Display Type  
TFT LCD Active Matrix  
Screen Size  
vp15:  
vp17:  
15.0 in.  
17.0 in.  
19.0 in.  
17.0 in.  
19.0 in.  
19.0 in.  
20.0 in.  
22.0 in.  
38.1 cm  
43.2 cm  
48.3 cm  
43.2 cm  
48.3 cm  
48.3 cm  
50.8 cm  
55.9 cm  
vp19:  
FP1707:  
WF1907:  
w1907:  
w2007:  
w2207:  
Viewable Image Size  
vp15:  
vp17:  
15.0 in. diagonal  
17.0 in. diagonal  
19.0 in. diagonal  
17.0 in. diagonal  
19.0 in. diagonal  
19.0 in. diagonal  
20.0 in. diagonal  
22.0 in. diagonal  
38.1 cm  
43.2 cm  
48.3 cm  
43.2 cm  
48.3 cm  
48.3 cm  
50.8 cm  
55.9 cm  
vp19:  
FP1707:  
WF1907:  
w1907:  
w2007:  
w2207:  
o
o
Tilt  
–5 to +25  
Antiglare polarizer with hard coating (select models only)  
Face Treatment  
Maximum Weight (unpacked)  
vp15:  
vp17:  
vp19:  
FP1707:  
WF1907:  
w1907:  
w2007:  
w2207:  
6.8 lb  
3.1 kg  
5.3 kg  
5.7 kg  
4.6 kg  
4.9 kg  
5.0 kg  
6.0 kg  
9.0 kg  
11.7 lb  
12.6 lb  
10.1 lb  
10.8 lb  
11.0 lb  
13.3 lb  
19.8 lb  
User’s Guide  
B–1  
     
Technical Specifications  
Specifications (Continued)  
Dimensions (including base)  
vp15:  
vp17:  
vp19:  
FP1707:  
WF1907:  
w1907:  
w2007:  
w2207 (high position):  
w2207 (low position):  
Height x Width x Depth  
13.9 x 15.9 x 7.68 in.  
15.67 x 17.32 x 7.25 in.  
16.81 x 19.06 x 7.25 in.  
15.41 x 17.36 x 8.15 in.  
12.28 x 20.12 x 2.64 in.  
14.96 x 17.87 x 7.28 in.  
15.63 x 19.29 x 7.25 in.  
18.9 x 20.6 x 11.4 in.  
14.6 x 20.6 x 11.4 in.  
Height x Width x Depth  
354 x 405 x 195 mm  
398 x 440 x 184 mm  
427 x 484 x 184 mm  
392 x 441 x 207 mm  
312 x 511 x 67 mm  
380 x 454 x 185 mm  
396.9 x 490 x 184.2 mm  
481.3 x 523.5 x 289 mm  
371.2 x 523.5 x 289 mm  
Maximum Graphics Resolution  
vp15:  
vp17, vp19, FP1707:  
WF1907, w1907:  
w2007, w2207:  
1280 × 768 @ 75 Hz analog mode  
1280 × 1024 @ 75 Hz analog mode  
1440 × 900 @ 60 Hz analog mode  
1680 x 1050 @ 60 Hz analog mode  
Optimum Graphics Resolution  
vp15:  
vp17, vp19, FP1707:  
WF1907, w1907:  
w2007, w2207:  
1024 × 768 @ 75 Hz analog mode  
1280 × 1024 @ 75 Hz analog mode  
1440 × 900 @ 60 Hz analog mode  
1680 x 1050 @ 60 Hz analog mode  
Text Mode  
720 x 400  
Dot Pitch  
vp15:  
0.297 x 0.297 mm  
0.264 x 0.264 mm  
0.294 x 0.294 mm  
0.283 x 0.284 mm  
0.282 x 0.282 mm  
vp17, FP1707:  
vp19, WF1907:  
w1907:  
w2007, w2207:  
Horizontal Frequency  
(analog mode)  
vp15:  
24 to 63 kHz  
vp17, vp19, FP1707,  
WF1907, w1907:  
w2007, w2207:  
24 to 83 kHz  
24 to 82 kHz  
Vertical Refresh Rate  
(analog mode)  
vp15, vp17, vp19, FP1707  
WF1907, w1907, w2007:  
w2207:  
50 to 76 Hz  
48 to 76 Hz  
Environmental Requirements  
Temperature (independent of  
altitude):  
Operating Temperature  
Non-operating Temperature  
o
o
o
o
41 to 95 F  
5 to 35 C  
o
o
o
o
–29 to 140 F  
–20 to 60 C  
Relative Humidity  
Power Source  
20% to 80%  
100–240V , 50/60 Hz  
B–2  
User’s Guide  
Technical Specifications  
Specifications (Continued)  
Power Consumption  
vp15:  
vp17:  
31 watts maximum  
45 watts maximum  
47 watts maximum  
45 watts maximum  
49 watts maximum  
49 watts maximum  
52 watts maximum  
65 watts maximum  
vp19:  
FP1707:  
WF1907:  
w1907:  
w2007:  
w2207:  
Sleep Power Consumption  
Input Terminals  
<2 watts typical  
VGA 15-pin D-type connector  
DVI-D 24-pin D-type connector  
(select models only)  
Preset Video Modes  
This monitor automatically recognizes many preset video input modes that will appear properly sized and centered  
on the screen. The following modes are assigned at the factory and are the most commonly used display resolutions:  
vp15 supports preset modes 1 through 11  
vp17, vp19, and FP1707 supports preset modes 1 through 15  
Factory Preset Video Input Modes, vp15, vp17, vp19, FP1707  
Horizontal  
Pixel Format Frequency (kHz)  
Vertical  
Frequency (Hz)  
Preset  
1
640 x 480  
640 x 480  
640 x 480  
720 x 400  
800 x 600  
800 x 600  
800 x 600  
832 x 624  
1024 x 768  
1024 x 768  
1024 x 768  
1152 x 870  
1152 x 900  
1280 x 1024  
1280 x 1024  
31.4  
37.8  
37.5  
31.4  
37.8  
48.0  
46.8  
49.7  
48.3  
56.4  
60.0  
68.6  
71.7  
63.9  
79.9  
59.9  
72.8  
75.0  
70.0  
60.3  
72.1  
75.0  
74.5  
60.0  
70.0  
75.0  
75.0  
76.1  
60.2  
75.0  
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
User’s Guide  
B–3  
   
Technical Specifications  
WF1907 and w1907 supports preset modes 1 through 16  
Factory Preset Video Input Modes, WF1907, w1907  
Horizontal  
Pixel Format Frequency (kHz)  
Vertical  
Frequency (Hz)  
Preset  
1
640 x 480  
640 x 480  
31.5  
37.5  
31.5  
37.9  
46.9  
49.7  
48.4  
60.0  
44.9  
68.7  
61.8  
47.4  
60.0  
63.9  
79.9  
55.9  
59.9  
2
3
75.0  
720 x 400  
70.0  
4
800 x 600  
60.3  
5
800 x 600  
75.0  
6
832 x 624  
74.5  
7
1024 x 768  
1024 x 768  
1152 x 720  
1152 x 870  
1152 x 900  
1280 x 768  
1280 x 960  
1280 x 1024  
1280 x 1024  
1440 x 900  
60.0  
8
75.0  
9
60.0  
10  
11  
12  
13  
14  
15  
16  
75.1  
65.9  
60.0  
60.0  
60.0  
75.0  
59.9  
w2007 supports preset modes 1 through 18  
Factory Preset Video Input Modes, w2007  
Horizontal  
Vertical  
Frequency (Hz)  
Preset  
Pixel Format Frequency (kHz)  
1
640 x 480  
640 x 480  
720 x 400  
800 x 600  
800 x 600  
832 x 624  
1024 x 768  
1024 x 768  
1024 x 768  
1152 x 720  
1152 x 870  
1152 x 900  
1280 x 768  
1280 x 960  
1280 x 1024  
31.4  
37.5  
31.5  
37.9  
46.8  
49.7  
48.3  
60.0  
68.6  
44.8  
68.7  
61.8  
47.4  
60.0  
63.9  
59.9  
75.0  
70.0  
60.3  
75.0  
74.5  
60.0  
75.0  
85.0  
60.0  
75.0  
65.9  
76.1  
60.0  
60.0  
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
B–4  
User’s Guide  
Technical Specifications  
Factory Preset Video Input Modes, w2007 (Continued)  
Horizontal  
Vertical  
Preset  
16  
Pixel Format Frequency (kHz)  
Frequency (Hz)  
1280 x 1024  
1440 x 900  
1680 x 1050  
79.9  
59.9  
65.2  
75.0  
59.9  
60.0  
17  
18  
w2207 supports preset modes 1 through 18  
Factory Preset Video Input Modes, w2207  
Horizontal  
Vertical  
Frequency (Hz)  
Preset  
Pixel Format Frequency (kHz)  
1
640 x 480  
640 x 480  
31.4  
37.5  
31.5  
37.9  
46.9  
49.7  
48.4  
60.0  
44.8  
68.7  
61.8  
47.4  
60.0  
63.9  
79.9  
55.9  
61.6  
65.3  
59.9  
75.0  
70.0  
60.3  
75.0  
74.5  
60.0  
75.0  
60.0  
75.1  
65.9  
60.0  
60.0  
60.0  
75.0  
59.9  
60.0  
60.0  
2
3
720 x 400  
4
800 x 600  
5
800 x 600  
6
832 x 624  
7
1024 x 768  
1024 x 768  
1152 x 720  
1152 x 870  
1152 x 900  
1280 x 768  
1280 x 960  
1280 x 1024  
1280 x 1024  
1440 x 900  
1600 x 1000  
1680 x 1050  
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
User’s Guide  
B–5  
Technical Specifications  
LCD Monitor Quality and Pixel Policy  
The HP LCD Monitor uses high-precision technology, manufactured according to high standards, to help guarantee  
trouble-free performance. Nevertheless, the display may have cosmetic imperfections that appear as small bright or  
dark spots. This is common to all LCD displays used in products supplied by all vendors and is not specific to the  
HP LCD Monitor. These imperfections are caused by one or more defective pixels or subpixels.  
A pixel consists of one red, one green, and one blue subpixel.  
A defective whole pixel is always turned on (a bright spot on a dark background), or it is always off (a dark spot  
on a bright background). The first is the more visible of the two.  
A defective subpixel (dot defect) is less visible than a defective whole pixel, and is small and only visible on a  
specific background.  
To locate defective pixels, the monitor should be viewed under normal operating conditions and in normal operating  
mode at a supported resolution and refresh rate, from a distance of approximately 50 cm (16 inches).  
We expect that, over time, the industry will continue to improve its ability to produce displays with fewer cosmetic  
imperfections, and we will adjust guidelines as improvements are made.  
Power Cord Set Requirements  
The monitor power supply is provided with Automatic Line Switching (ALS). This feature allows the monitor to operate  
on input voltages between 100–240Vv, 50/60 Hz, 1.5A.  
The power cord set (flexible cord or wall plug) received with the monitor meets the requirements for use in the  
country/region where you purchased the equipment.  
If you need to obtain a power cord for a different country/region, you should purchase a power cord that is  
approved for use in that country/region.  
The power cord must be rated for the product and for the voltage and current marked on the product’s electrical  
ratings label. The voltage and current rating of the cord should be greater than the voltage and current rating marked  
²
on the product. In addition, the cross-sectional area of the wire must be a minimum of 0.75 mm or 18AWG, and the  
length of the cord must be between 4.94 ft. (1.5 m) and 12 ft. (3.6 m). If you have questions about the type of power  
cord to use, contact your HP-authorized service provider.  
A power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it or against  
it. Particular attention should be paid to the plug, electrical outlet, and the point where the cord exits from the  
product.  
B–6  
User’s Guide  
     
C
Agency Regulatory Notices  
Federal Communications Commission Notice  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15  
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a  
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed  
and used in accordance with the instructions, may cause harmful interference to radio communications. However,  
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be determined by turning the equipment off and on, the user  
is encouraged to try to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and the receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio or television technician for help.  
Modifications  
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly  
approved by Hewlett-Packard Company may void the user’s authority to operate the equipment.  
Cables  
Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to maintain  
compliance with FCC rules and regulations.  
Declaration of Conformity for Products Marked with FCC Logo,  
United States Only  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this  
device may not cause harmful interference, and (2) this device must accept any interference received, including  
interference that may cause undesired operation.  
For questions regarding your product, contact:  
Hewlett-Packard Company  
P. O. Box 692000, Mail Stop 530113  
Houston, Texas 77269-2000  
Or  
Call: 1-800-474-6836  
For questions regarding this FCC declaration, contact:  
Hewlett-Packard Company  
P. O. Box 692000, Mail Stop 510101  
Houston, Texas 77269-2000  
Or  
Call: 1-281-514-3333  
To identify this product, refer to the part, series, or model number found on the product.  
User’s Guide  
C–1  
         
Agency Regulatory Notices  
Materials Disposal  
This HP product contains mercury in the fluorescent lamp in the display LCD that might require special handling at  
end-of-life:  
Disposal of this material can be regulated because of environmental considerations. For disposal or recycling  
information, contact your local authorities or the Electronic Industries Alliance (EIA) (http://www.eiae.org).  
Canadian Notice  
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.  
Avis Canadien  
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du  
Canada.  
European Union Regulatory Notice  
This product complies with the following EU Directives:  
Low Voltage Directive 73/23/EEC  
EMC Directive 89/336/EEC  
Compliance with these directives implies conformity to applicable harmonized European standards (European  
Norms) which are listed on the EU Declaration of Conformity issued by Hewlett-Packard for this product or product  
family.  
This compliance is indicated by the following conformity marking placed on the product:  
XXXX*  
This marking is valid for  
non-Telecom products and  
EU harmonized Telecom  
products (e.g. Bluetooth).  
This marking is valid for EU  
non-harmonized Telecom  
products.  
*Notified body number (used  
only if applicable — refer to the  
product label).  
Hewlett-Packard GmbH, HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, Germany  
Disposal of Waste Equipment by Users in Private Households in  
the European Union  
This symbol on the product or on its packaging indicates that this product must not be disposed of  
with your other household waste. Instead, it is your responsibility to dispose of your waste  
equipment by handing it over to a designated collection point for the recycling of waste electrical  
and electronic equipment. The separate collection and recycling of your waste equipment at the  
time of disposal will help to conserve natural resources and ensure that it is recycled in a manner  
that protects human health and the environment. For more information about where you can drop  
off your waste equipment for recycling, please contact your local city office, your household  
waste disposal service or the shop where you purchased the product.  
C–2  
User’s Guide  
         
Agency Regulatory Notices  
Japanese Notice  
Japanese Power Cord Notice  
Japanese Material Content Declaration  
A Japanese regulatory requirement, defined by Specification JIS C 0950, 2005, mandates that manufacturers  
provide Material Content Declarations for certain categories of electronic products offered for sale after July 1,  
Korean Notice  
EPA Energy Star Compliance  
®
Products marked with the ENERGY STAR logo on the packaging box qualify with the U.S.  
®
Environmental Protection Agency’s ENERGY STAR guidelines for energy efficiency.  
®
Products with the ENERGY STAR label are designed to use less energy, help you save money on  
utility bills, and help protect the environment.  
®
ENERGY STAR is a registered trademark owned by the U.S. government.  
User’s Guide  
C–3  
         
Agency Regulatory Notices  
HP Recycling Program  
HP offers product end-of-life return programs for HP and other manufacturers’ hardware in several geographic areas.  
The terms and availability of these programs vary by geography because of differences in regulatory requirements  
and local customer demand. For information on the HP recycling program, refer to the HP Web site at:  
The Table of Toxic and Hazardous Substances/Elements and their Content  
as required by China’s  
Management Methods for Controlling Pollution by Electronic Information Products  
Toxic and Hazardous Substances and Elements  
Part Name  
Lead Mercury  
Cadmium  
(Cd)  
Hexavalent  
Chromium  
(Cr(VI))  
Polybrominated  
biphenyls (PBB)  
Polybrominated  
diphenyl ethers  
(PBDE)  
(Pb)  
(Hg)  
Liquid Crystal Display  
Panel  
X
X
O
O
O
O
Chassis/Other  
X
O
O
O
O
O
O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below  
the limit requirement in SJ/T11363-2006.  
X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this  
part is above the limit requirement in SJ/T11363-2006.  
All parts named in this table with an “X” are in compliance with the European Union’s RoHS Legislation – “Directive  
2002/95/EC of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain  
hazardous substances in electrical and electronic equipment”.  
Note: The referenced Environmental Protection Use Period Marking was determined according to normal operating use  
conditions of the product such as temperature and humidity.  
“˅ꢀƅɦƅǧĭᯬz̯௤Ոȑ
ǎȯₓꢁ  
˾Ϣɋ6εϹʖͮǯ˨˵˄$ġɼǂ¢Ǣζ  
ƅɦƅǧĭᯬz̯௤  
ᾬâȑ
 
̶Šxᆳ⁞  
⎉ꢁ(Pb)  
Ɩ
␍ꢁ(Cd)  
˜ˊ⎰ꢁ ŹŠ༘˦  
(PBDE)  
(Hg)  
(Cr(VI))  
(PBB)  
O
X
X
X
O
O
O
O
O
O
^òº
߾
ʃ  
O
O
ƶੵ/͢Âꢁ  
Oꢁᜬ
߾
᪩ƅɦƅǧĭᯬń᪩ᾬâ¤ƅţᯬnjꢂꢃՈȯₓţńSJ/T11363-2006 ʃβᢈǎՈ└ₓᡅ˖Ñ[4ꢀ  
Xꢁᜬ
߾
᪩ƅɦƅǧĭᯬႷɅń᪩ᾬâՈɌPţᯬnjꢂꢃՈȯₓ᱉ϦSJ/T11363-2006 ʃβᢈǎՈ└ₓᡅ˖4ꢀ  
؛
ɋʃȽPX” ̪͛Ƚૡˉ૪ȫɯßΖ RoHS Ǣᢈ  
ßȖˣ˂ßΖǂʀˣ 2003  1 ȼ 27 ų͟ʃϹʖϹς᪂̣ɋꢀġ̦ɪˁʌȽˢÛ͛ 2002/95/EC ɨΨʾQ  
ǰዖɳ̦ͫɪɌꢀ͛ȻĘʃ᪊ɊÈʃ˨Ąi7̎͛ʟª˂ːªɄɶˉ  
Part number: 440143-002  
C–4  
User’s Guide  
 

GE Monogram ZET2P User Manual
Frymaster GBC User Manual
Eizo Nanao Computer Monitor FDU2602W User Manual
Diamond Multimedia Radeon S60PCI User Manual
Diamond Multimedia ATI Radeon Stealth SKU 2400PRO512A User Manual
Dell E248WFP User Manual
CyberResearch CPEX P4 32 X User Manual
Asus P9X79 WS User Manual
Asus P4S333 User Manual
25826GE User Manual