User’s Manual
2807700
Version 1.0
Table of Contents
Introduction.......................................................1
Checklist..............................................................................1
Product Description.............................................................2
Specifications ...................................................................... 3
Board Dimensions...............................................................4
Installations.......................................................5
Installing the CPU...............................................................6
ATX Power Installation ...................................................... 6
Installing the Memory .........................................................7
Setting the Jumpers ............................................................. 8
Connectors on 2807700.......................................................12
BIOS Setup.......................................................23
Drivers Installation......................................45
Intel Q965 Chipset Software Installation Utility...............46
Intel Q965 Chipset Graphics Driver..................................48
Realtek Codec Audio Driver Installation ..........................50
Intel LAN Drivers Installation ..........................................51
Appendix ...........................................................55
A. I/O Port Address Map...................................................55
B. Interrupt Request Lines (IRQ)......................................56
C. Watchdog Timer Configuration....................................57
Contact Information ..................................62
2807700 User’s Manual
iii
This page is intentionally left blank.
iv
2807700 User’s Manual
INTRODUCTION
Introduction
Checklist
Your 2807700 Core 2 Duo motherboard package should include the
items listed below:
•
•
•
•
•
•
The 2807700 motherboard
This User’s manual
1 x I/O shield
1 x IDE cable
1 x SATA cable
1 CD containing the following:
•
•
Chipset Drivers
Flash Memory Utility
2807700 User’s Manual
1
INSTALLATIONS
Product Description
The 2807700 Mini-ITX motherboard is designed for either the
Intel® Core™2 Duo or Intel® Pentium® D processors of up to
1066MHz FSB. It is based on the Intel’s Q965 Express chipset
and it comes with two single-channel DDR2 memory slots and
4GB memory capacity for faster system responsiveness and
support of 64-bit computing. The new Global American, Inc
motherboards are aimed for high performance PCs in the digital,
communications and industrial sector.
On board is one PCI Express x16 slot that offers up to 3.5X the
bandwidth over traditional PCI architecture to support the latest
high-performance graphics cards. Dual independent display
comes to life with the onboard Intel® Q965 integrated graphics for
CRT and an optional SDVO card supporting either an LVDS or
DVI display interface. LAN functionality is supported with a 10/100
Ethernet controller or with two Gigabit Ethernet controllers.
2807700 is expandable for 8x2 pins pin header for adaptor card
ID394 that support 2 or 4 serial ports, or ID395 that support TPM
1.2 for security function. Other useful features on the board
include four SATA II ports, six USB 2.0 interface, watchdog timer,
digital I/O and two serial ports. Board dimensions are 170mm by
170mm. (Note: CPU power consumption – under 95watt
recommended.)
2807700 FEATURES
·
·
·
·
·
·
·
·
Intel® Q965 Express Chipset Based
Support LGA775 Intel® Core™2 Duo Processors
Support FSB 1066/800/533MHz
Support up to 4GB DDRII 800/667/533 memory
1 x PCI Express(x16)
Support one 10/100 or two Gigabit LAN on board
4 x SATA II, 1 x IDE, 6 x USB 2.0, 2 x COM,
7.1Ch.HD Audio
2
2807700 User’s Manual
INTRODUCTION
Specifications
Processor
FSB
Supports Intel Core 2 Duo processor (Conroe core) in LGA775 socket
533/800/1066 MHz
Chipset
Intel Q965 Chipset consisting of:
•
•
Intel Q965 Graphic Memory Controller Hub (GMCH)
Intel ICH8 I/O Controller Hub
BIOS
Memory
•
•
•
Award BIOS: SPI interface only, supports ACPI, SMBIOS
Two 240-pin DDRII 533/667/800 DIMM sockets (2x single ch)
Supports max. 4 GB system memory
Video
LAN
Intel Q965 integrated graphic subsystem (GMA3000), dual independent
display available through on-board VGA and PCI-e x16 expansion
adapter (DVI or LVDS) or VGA card
LAN1: dual Footprint support option:
•
Intel 82566DC Nineveh 10/100/1000 LAN
•
Intel 82562V Ekron-N 10/100
LAN2: Marvell 88E8053 PCI-express Gigabit LAN controller x1
USB
Intel ICH8 built-in USB 2.0 host controller, supports 6 ports:
•
•
4 ports in the rear I/O region
2 ports with on-board headers
SATA II
IDE
Intel ICH8 built-in SATA II controller (3.0Gb/sec) w/ 4 ports
JMicron JMB368 (PCI-e to PATA) x1 for 1 PATA channel
Audio
LPC I/O
Intel ICH8 built-in high definition audio w/ Realtek ALC888 Codec
Winbond W83627EHF: COM1 (RS232), COM2 (RS232/422/485) &
Hardware monitor
•
Mini-DIN for PS/2 KB & MS, DB9 connector for COM1, DB15
connector for VGA, RJ45 + dual USB stack connector x2 for
LAN1~2 and USB1~4, Triple (3x1) audio phone jack stack connector
SATA (7-pin shrouded vertical) connector x4, USB 5-6, COM2
(RS232/422/485), Digital I/O, 7.1 channel audio, IDE, CPU fan &
system fan headers
Edge
Connectors
On
Headers
Connectors
Board
•
/
Expansion
PCI-express (x16) slot x1
8x2 pins pin-header x1 for adaptor card:
-
-
ID394 (2 or 4 serial ports - Fintek F81216)
ID395 (TPM1.2 – Winbond WPCT200/ATMEL AT97SC3203
co-layout)
RTC
Watchdog
Timer
ICH8 built-in RTC with on-board lithium battery
Yes (256 segments, 0, 1, 2…255 sec/min)
Digital IO
Other
4 in and 4 Out
LAN Wakeup
Power
Connector
System
24 pins ATX main power + 4 pins 12V
CPU Power: 95W max.
+5V, +3.3V, +12V, -12V & 5VSB
Voltage
Board Size
170 x 170mm
2807700 User’s Manual
3
INSTALLATIONS
Board Dimensions
4
2807700 User’s Manual
INSTALLATIONS
Installations
This section provides information on how to use the jumpers and
connectors on the 2807700 in order to set up a workable system.
The topics covered are:
Installing the CPU........................................................................ 6
ATX Power Installation ............................................................... 6
Installing the Memory.................................................................. 7
Setting the Jumpers...................................................................... 8
Connectors on 2807700 .............................................................. 12
2807700 User’s Manual
5
INSTALLATIONS
Installing the CPU
The 2807700 motherboard supports an LGA 775 processor socket for
Intel® Core 2 Duo processors.
The LGA 775 processor socket comes with a lever to secure the
processor. Refer to the pictures below, from left to right, on how to place
the processor into the CPU socket. Please note that the cover of the
LGA775 socket must always be installed during transport to avoid
damage to the socket.
ATX Power Installation
The system power is provided to the motherboard with the ATX1 and
ATX2 power connectors. ATX1 is a 24-pin power connector and ATX2
is a 4-pin 12V power connector.
The 24-pin power connector can to be connected to a standard 20-pin
ATX power connector in a standard ATX power supply (Min. 400watt).
Note: The power supply 5VSB voltage must be at least 2A.
6
2807700 User’s Manual
INSTALLATIONS
Installing the Memory
The 2807700 motherboard supports four DDR2 memory sockets for
a maximum total memory of 4GB in DDR memory type. It
supports DDR2 533/667/800.
Basically, the system memory interface has the following features:
Supports two 64-bit wide DDR data channels
Available bandwidth up to 6.4GB/s (DDR2 800) for single-channel
mode.
Supports 256Mb, 512Mb, 1Gb DDR2 technologies.
Supports only x8, x16, DDR2 devices with four banks
Supports only unbuffered DIMMs
Supports opportunistic refresh
Up to 32 simultaneously open pages (four per row, four rows
maximum)
2807700 User’s Manual
7
INSTALLATIONS
Setting the Jumpers
Jumpers are used on the motherboard are used to select various settings
and features according to your needs and applications. Contact your
supplier if you have doubts about the best configuration for your needs.
The following lists the connectors and their respective functions.
Jumper Locations on 2807700A/2807700B.................................... 9
JBAT1: Clear CMOS Contents..................................................... 10
JP1, JP2, JP3: RS232/422/485 (COM2) Selection ....................... 10
JP6: Processor Setting................................................................... 10
J6: Power ON Setting ................................................................... 11
8
2807700 User’s Manual
INSTALLATIONS
Jumper Locations on 2807700A/2807700B
Jumper Locations on 2807700A/2807700B ................................... 9
JBAT1: Clear CMOS Contents .................................................... 10
JP1, JP2, JP3: RS232/422/485 (COM2) Selection....................... 10
JP6: Processor Setting .................................................................. 10
J6: Power ON Setting................................................................... 11
2807700 User’s Manual
9
INSTALLATIONS
JBAT1: Clear CMOS Contents
Use JBAT1, a 3-pin header, to clear the CMOS contents. Note that the
ATX-power connector should be disconnected from the motherboard
before clearing CMOS.
JBAT1
Setting
Function
Pin 1-2
Short/Closed
Normal
Pin 2-3
Short/Closed
Clear CMOS
JP1, JP2, JP3: RS232/422/485 (COM2) Selection
COM1 is fixed for RS-232 use only.
COM2 is selectable for RS232, RS-422 and RS-485.
ID394: COM3 and COM4 are fixed for RS-232 use only. The following
table describes the jumper settings for COM2 selection.
COM2
RS-232
JP3:
RS-422
JP3:
RS-485
JP3:
Function
1-2
3-4
5-6
Jumper
Setting
JP1:
JP1:
JP1:
(pin closed) 3-5 & 4-6
1-3 & 2-4
1-3 & 2-4
JP2:
JP2:
JP2:
3-5 & 4-6
1-3 & 2-4
1-3 & 2-4
JP6: Processor Setting
JP6
Setting
Processor Used
Pin 1-2
Short/Closed
Celeron D
Core 2 Duo,
Pentium D,
Pentium 4 HT
Pin 1-2
Open
10
2807700 User’s Manual
INSTALLATIONS
J6: Power ON Setting
J6
Setting
Function
Pin 1-2
Power on by system
Short/Closed
button
Pin 2-3
Power on by power
supply AC on
Short/Closed
2807700 User’s Manual
11
INSTALLATIONS
Connectors on 2807700
The connectors on 2807700 allows you to connect external devices such
as keyboard, floppy disk drives, hard disk drives, printers, etc.
The following table lists the connectors on 2807700 and their
respective functions.
ATX1: 24-pin ATX Power Connector..............................................................14
ATX2: ATX 12V Power Connector.................................................................14
CPU_FAN1: CPU Fan Power Connector........................................................14
PWR_FAN1: SYSTEM Fan Power Connectors...............................................14
CN2: PS/2 Keyboard and PS/2 Mouse Connectors ..........................................15
CN1 J3: COM1/2 Serial Ports ..........................................................................15
VGA1: VGA CRT Connector ..........................................................................16
CN3: Marvell 88E8053 PCI-express Gigabit LAN and USB6/7 Connector ...16
CN6: Intel 82562V 10/100 or Intel 82566DC GbE RJ-45 and USB4/5 Connector .........16
CN4: Audio Connector.....................................................................................16
F_USB1: USB0/USB1 Connector....................................................................17
S_ATA1, S_ATA2, S_ATA3, S_ATA4: SATA HDD Connectors..................17
IDE1: Primary IDE Connectors........................................................................17
J2: Digital I/O Connector (4 in, 4 out)..............................................................18
J4: External Audio Connector for 7.1 channel .................................................18
JP4: For LPC I/F Adaptor Card........................................................................18
ID394 with Fintek F81216, 2 or 4 Serial Ports.................................................18
ID395 Winbond WPCT200 x1 for TPM1.2 .....................................................18
J5: Power LED .................................................................................................18
J7: System Function Connector........................................................................19
PCIE_1: x16 PCI Express Slot .........................................................................19
ID394 LPC Serial Ports Adaptor Card .............................................................20
ID395 WINBOND WPCT200 for TPM1.2......................................................21
12
2807700 User’s Manual
INSTALLATIONS
Connector Locations on 2807700A/2807700B
ATX1: 24-pin ATX Power Connector................................................................................................... 14
ATX2: ATX 12V Power Connector ...................................................................................................... 14
CPU_FAN1: CPU Fan Power Connector............................................................................................. 14
PWR_FAN1: SYSTEM Fan Power Connectors ................................................................................... 14
CN2: PS/2 Keyboard and PS/2 Mouse Connectors............................................................................... 15
CN1 J3: COM1/2 Serial Ports................................................................................................................ 15
VGA1: VGA CRT Connector................................................................................................................ 16
CN3: Marvell 88E8053 PCI-express Gigabit LAN and USB6/7 Connector........................................ 16
CN6: Intel 82562V 10/100 or Intel 82566DC GbE RJ-45 and USB4/5 Connector................................................. 16
CN4: Audio Connector .......................................................................................................................... 16
F_USB1: USB0/USB1 Connector ......................................................................................................... 17
S_ATA1, S_ATA2, S_ATA3, S_ATA4: SATA HDD Connectors...................................................... 17
IDE1: Primary IDE Connectors............................................................................................................. 17
J2: Digital I/O Connector (4 in, 4 out)................................................................................................... 18
J4: External Audio Connector for 7.1 channel ...................................................................................... 18
JP4: For LPC I/F Adaptor Card ............................................................................................................. 18
J5: Power LED....................................................................................................................................... 18
J7: System Function Connector ............................................................................................................. 19
PCIE_1: x16 PCI Express Slot .............................................................................................................. 19
2807700 User’s Manual
13
INSTALLATIONS
ATX1: 24-pin ATX Power Connector
Signal Name Pin # Pin #
Signal Name
3.3V
3.3V
-12V
13
14
15
16
17
18
19
20
21
22
23
24
1
2
3.3V
Ground
+5V
Ground
+5V
Ground
Power good
5VSB
Ground
PS-ON
Ground
Ground
Ground
-5V
3
4
5
6
7
8
+5V
9
+5V
+5V
Ground
10
11
12
+12V
+12V
+3.3V
ATX2: ATX 12V Power Connector
This connector supplies the CPU operation voltage
Pin #
Signal Name
Ground
Ground
+12V
1
2
3
4
+12V
CPU_FAN1: CPU Fan Power Connector
Pin #
Signal Name
Control
Sense
1
2
3
4
+12V
Ground
PWR_FAN1: SYSTEM Fan Power Connectors
Pin #
Signal Name
1
2
3
Sense
+12V
Rotation detection
14
2807700 User’s Manual
INSTALLATIONS
CN2: PS/2 Keyboard and PS/2 Mouse Connectors
Keyboard Signal
Pin #
Mouse Signal
Keyboard data
N.C.
GND
5V
Keyboard clock
N.C.
1
2
3
4
5
6
Mouse data
N.C.
GND
5V
Mouse clock
N.C.
Mouse (top)
Keyboard (bottom)
CN1 J3: COM1/2 Serial Ports
CN1 (COM1) is a DB-9 connector, while J3 are COM pin-header
connectors.
Signal Name
DCD, Data carrier detect
RXD, Receive data
TXD, Transmit data
DTR, Data terminal ready
GND, ground
Pin # Pin #
Signal Name
DSR, Data set ready
RTS, Request to send
CTS, Clear to send
RI, Ring indicator
Not Used
1
2
3
4
5
6
7
8
9
10
J3: COM2 is jumper selectable for RS-232, RS-422 and RS-485.
Pin #
Signal Name
RS-232
DCD
RX
R2-422
TX-
TX+
RS-485
DATA-
DATA+
NC
1
2
3
TX
RX+
4
5
6
7
8
9
10
DTR
Ground
DSR
RTS
CTS
RI
RX-
NC
Ground
NC
NC
NC
Ground
RTS-
RTS+
CTS+
CTS-
NC
NC
NC
NC
2807700 User’s Manual
15
INSTALLATIONS
VGA1: VGA CRT Connector
VGA1 is a DB-15 VGA connector located beside the COM1 port. The
following table shows the pin-out assignments of this connector.
Signal Name Pin # Pin # Signal Name
Red
Blue
1
3
2
4
Green
N.C.
GND
5
6
GND
GND
7
8
GND
VCC
N.C.
HSYNC
DDCCLK
9
10
12
14
GND
DDCDATA
VSYNC
11
13
15
CN3: Marvell 88E8053 PCI-express Gigabit LAN and USB6/7
Connector
CN6: Intel 82562V 10/100 or Intel 82566DC GbE RJ-45 and
USB4/5 Connector
Note: 10/100 LAN for 2807700A; DUAL Gigabit LAN for 2807700F
CN4: Audio Connector
CN4 is a 3-jack audio connector
16
2807700 User’s Manual
INSTALLATIONS
F_USB1: USB0/USB1 Connector
Signal Name Pin Pin Signal Name
Vcc
1
3
5
7
2
4
6
8
Ground
USB1+
USB1-
Vcc
USB0-
USB0+
Ground
S_ATA1, S_ATA2, S_ATA3, S_ATA4: SATA HDD Connectors
Pin # Signal Name
1
2
3
4
5
6
7
Ground
TX+
TX-
Ground
RX-
RX+
Ground
IDE1: Primary IDE Connectors
Signal Name
Pin #
Pin #
Signal Name
Reset IDE
Host data 7
Host data 6
Host data 5
Host data 4
Host data 3
Host data 2
Host data 1
Host data 0
Ground
1
2
Ground
Host data 8
Host data 9
Host data 10
Host data 11
Host data 12
Host data 13
Host data 14
Host data 15
Protect pin
Ground
3
4
5
6
8
7
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
DRQ0
Host IOW
Host IOR
IOCHRDY
DACK0
Ground
Ground
Host ALE
Ground
No connect
No connect
Address 2
Chip select 1
Ground
IRQ14
IDE1
Address 1
Address 0
Chip select 0
Activity
2807700 User’s Manual
17
INSTALLATIONS
J2: Digital I/O Connector (4 in, 4 out)
This 10-pin digital I/O connector supports TTL levels and is used to
control external devices requiring ON/OFF circuitry.
Signal Name Pin #
Pin # Signal Name
Ground
Out3
Out2
IN3
1
3
5
7
9
2
4
6
8
10
+5V
Out1
Out0
IN1
IN2
IN0
J4: External Audio Connector for 7.1 channel
Signal Name
Pin # Pin #
Signal Name
SIDESURR_R
Ground
SIDESURR_L
SIDESURR
1
3
2
4
Detect
SURR_Out_L
SURR_Out Detect
Center_Out
5
7
6
SURR_Out_R
Ground
LFE_Out
Ground
8
9
10
12
Center/ LFE Detect
11
JP4: For LPC I/F Adaptor Card
ID394 with Fintek F81216, 2 or 4 Serial Ports
ID395 Winbond WPCT200 x1 for TPM1.2
J5: Power LED
The power LED indicates the status of the main power switch.
Pin # Signal Name
1
2
3
Power LED
No connect
Ground
18
2807700 User’s Manual
INSTALLATIONS
J7: System Function Connector
ATX Power ON Switch: Pins 1 and 2
This 2-pin connector is an “ATX Power Supply On/Off Switch” on the
system that connects to the power switch on the case. When pressed, the
power switch will force the system to power on. When pressed again, it
will force the system to power off.
Hard Disk Drive LED Connector: Pins 3 and 4
This connector connects to the hard drive activity LED on control panel.
This LED will flash when the HDD is being accessed.
Pin #
4
3
Signal Name
HDD Active
5V
Reset Switch: Pins 5 and 6
The reset switch allows the user to reset the system without turning the
main power switch off and then on again. Orientation is not required
when making a connection to this header.
+5V and 5VSB Signals: Pins 7 and 8
Pin #
7
8
Signal Name
+5V
+5VSB
PCIE_1: x16 PCI Express Slot
2807700 User’s Manual
19
INSTALLATIONS
ID394 LPC Serial Ports Adaptor Card
J1 J2: COM3/4/5/6 Serial Ports
J1 - COM3/4 pin-header connector.
PIN1~PIN10 COM3
PIN11~PIN20 COM4
J2 - COM5/6 pin-header connector.
PIN1~PIN10 COM5
PIN11~PIN20 COM6
Signal Name
DCD, Data carrier detect
RXD, Receive data
TXD, Transmit data
DTR, Data terminal ready
GND, ground
DCD, Data carrier detect
RXD, Receive data
TXD, Transmit data
DTR, Data terminal ready
GND, ground
Pin # Pin #
Signal Name
DSR, Data set ready
RTS, Request to send
CTS, Clear to send
RI, Ring indicator
Not Used
DSR, Data set ready
RTS, Request to send
CTS, Clear to send
RI, Ring indicator
Not Used
1
3
2
4
5
6
7
8
9
10
12
14
16
18
20
11
13
15
17
19
CN1: LPC I/F connectors
Package list:
COM port cable (PK1-20B) x 2
Nylon Nut x 1
Screw x 2
Washer x2
20
2807700 User’s Manual
INSTALLATIONS
ID395 WINBOND WPCT200 for TPM1.2
CN1: LPC I/F connectors
Package list
Nylon Nut x 1
Screw x 2
Washer x2
2807700 User’s Manual
21
INSTALLATIONS
This page is intentionally left blank.
22
2807700 User’s Manual
BIOS SETUP
BIOS Setup
This chapter describes the different settings available in the Award
BIOS that comes with the board. The topics covered in this chapter are
as follows:
BIOS Introduction ........................................................................ 24
BIOS Setup................................................................................... 24
Standard CMOS Setup ................................................................. 26
Advanced BIOS Features ............................................................. 29
Advanced Chipset Features .......................................................... 32
Integrated Peripherals................................................................... 33
Power Management Setup............................................................ 36
PNP/PCI Configurations .............................................................. 38
PC Health Status........................................................................... 39
Frequency/Voltage Control .......................................................... 40
Load Fail-Safe Defaults................................................................ 41
Load Optimized Defaults ............................................................. 41
Set Supervisor/User Password...................................................... 41
Save & Exit Setup ........................................................................ 41
Exit Without Saving ..................................................................... 41
2nd SuperIO Device.................................................................... 38
Security Chip Configuration......................................................... 39
2807700 User’s Manual
23
BIOS SETUP
BIOS Introduction
The Award BIOS (Basic Input/Output System) installed in your
computer system’s ROM supports Intel processors. The BIOS provides
critical low-level support for a standard device such as disk drives, serial
ports and parallel ports. It also adds virus and password protection as
well as special support for detailed fine-tuning of the chipset controlling
the entire system.
BIOS Setup
The Award BIOS provides a Setup utility program for specifying the
system configurations and settings. The BIOS ROM of the system stores
the Setup utility. When you turn on the computer, the Award BIOS is
immediately activated. Pressing the <Del> key immediately allows you
to enter the Setup utility. If you are a little bit late pressing the <Del>
key, POST (Power On Self Test) will continue with its test routines, thus
preventing you from invoking the Setup. If you still wish to enter Setup,
restart the system by pressing the ”Reset” button or simultaneously
pressing the <Ctrl>, <Alt> and <Delete> keys. You can also restart by
turning the system Off and back On again. The following message will
appear on the screen:
Press <DEL> to Enter Setup
In general, you press the arrow keys to highlight items, <Enter> to
select, the <PgUp> and <PgDn> keys to change entries, <F1> for help
and <Esc> to quit.
When you enter the Setup utility, the Main Menu screen will appear on
the screen. The Main Menu allows you to select from various setup
functions and exit choices.
24
2807700 User’s Manual
BIOS SETUP
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
Frequency/Voltage Control
Advanced BIOS Features
Advanced Chipset Features
Integrated Peripherals
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Power Management Setup
PnP/PCI Configurations
Save & Exit Setup
PC Health Status
Exit Without Saving
ESC : Quit
Ç È Æ Å : Select Item
F10 : Save & Exit Setup
Time, Date, Hard Disk Type…
The section below the setup items of the Main Menu displays the control
keys for this menu. At the bottom of the Main Menu just below the
control keys section, there is another section, which displays information
on the currently highlighted item in the list.
Note:
If the system cannot boot after making and saving system
changes with Setup, the Award BIOS supports an override to
the CMOS settings that resets your system to its default.
Warning: It is strongly recommended that you avoid making any
changes to the chipset defaults. These defaults have been
carefully chosen by both Award and your system
manufacturer to provide the absolute maximum performance
and reliability. Changing the defaults could cause the system
to become unstable and crash in some cases.
2807700 User’s Manual
25
BIOS SETUP
Standard CMOS Setup
“Standard CMOS Setup” choice allows you to record some basic
hardware configurations in your computer system and set the system
clock and error handling. If the motherboard is already installed in a
working system, you will not need to select this option. You will need to
run the Standard CMOS option, however, if you change your system
hardware configurations, the onboard battery fails, or the configuration
stored in the CMOS memory was lost or damaged.
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
Date (mm:dd:yy)
Time (hh:mm:ss)
Fri, Oct 20, 2006
16 : 11 : 00
Item Help
Menu Level >
IDE Channel 0 Master
IDE Channel 0 Slave
IDE Channel 1 Master
IDE Channel 1 Slave
IDE Channel 2 Master
IDE Channel 3 Master
IDE Channel 4 Master
IDE Channel 4 Slave
None
None
None
None
None
None
None
None
Change the day, month,
Year and century
Video
EGA/VGA
Halt On
All , But Keyboard
Base Memory
640K
Extended Memory
Total Memory
2086912K
2087936K
At the bottom of the menu are the control keys for use on this menu. If
you need any help in each item field, you can press the <F1> key. It will
display the relevant information to help you. The memory display at the
lower right-hand side of the menu is read-only. It will adjust
automatically according to the memory changed. The following
describes each item of this menu.
Date
The date format is:
Day :
Sun to Sat
1 to 12
1 to 31
Month :
Date :
Year :
1999 to 2099
26
2807700 User’s Manual
BIOS SETUP
To set the date, highlight the “Date” field and use the PageUp/
PageDown or +/- keys to set the current time.
Time
The time format is: Hour : 00 to 23
Minute : 00 to 59
Second : 00 to 59
To set the time, highlight the “Time” field and use the <PgUp>/ <PgDn>
or +/- keys to set the current time.
IDE Channel Master/Slave
The onboard Serial ATA connectors provide Primary and Secondary
channels for connecting up to four Serial ATA hard disks . Each channel
can support up to two hard disks; the first is the “Master” and the second
is the “Slave”.
Press <Enter> to configure the hard disk. The selections include Auto,
Manual, and None. Select ‘Manual’ to define the drive information
manually. You will be asked to enter the following items.
Capacity :
Cylinder :
Head :
Capacity/size of the hard disk drive
Number of cylinders
Number of read/write heads
Write precompensation
Precomp :
Landing Zone : Landing zone
Sector :
Number of sectors
The Access Mode selections are as follows:
CHS
(HD < 528MB)
LBA
(HD > 528MB and supports Logical Block Addressing)
Large (for MS-DOS only)
Auto
2807700 User’s Manual
27
BIOS SETUP
Drive A / Drive B
These fields identify the types of floppy disk drive A or drive B that has
been installed in the computer. The available specifications are:
360KB 1.2MB 720KB 1.44MB 2.88MB
5.25 in. 5.25 in. 3.5 in.
3.5 in.
3.5 in.
Video
This field selects the type of video display card installed in your system.
You can choose the following video display cards:
EGA/VGA
For EGA, VGA, SEGA, SVGA
or PGA monitor adapters. (default)
Power up in 40 column mode.
Power up in 80 column mode.
For Hercules or MDA adapters.
CGA 40
CGA 80
MONO
Halt On
This field determines whether or not the system will halt if an error is
detected during power up.
No errors
The systemboot will not be halted for any error
that may be detected.
All errors
Whenever the BIOS detects a non-fatal error,
the system will stop and you will be prompted.
The system boot will not be halted for a
keyboard error; it will stop for all other errors
The system boot will not be halted for a disk
error; it will stop for all other errors.
All, But Keyboard
All, But Diskette
All, But Disk/Key
The system boot will not be halted for a key-
board or disk error; it will stop for all others.
28
2807700 User’s Manual
BIOS SETUP
Advanced BIOS Features
This section allows you to configure and improve your system and
allows you to set up some system features according to your preference.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced BIOS Features
CPU Feature
Hard Disk Boot Priority
Virus Warning
CPU L1 and L2 Cache
Hyper-Threading Technology
Quick Power On Self Test
First Boot Device
Second Boot Device
Third Boot Device
Press Enter
Press Enter
Disabled
Enabled
Enabled
Enabled
Hard Disk
CDROM
USB-FDD
Enabled
On
ITEM HELP
Menu Level >
Boot Other Device
Boot Up NumLock Status
Gate A20 Option
Fast
Typematic Rate Setting
Typematic Rate (Chars/Sec)
Typematic Delay (Msec)
Security Option
Disabled
6
250
Setup
APIC Mode
Enabled
1.4
Non-OS2
Disabled
MPS Version Control for OS
OS Select For DRAM>64MB
Small Logo (EPA) Show
CPU Feature
Press Enter to configure the settings relevant to CPU Feature.
Hard Disk Boot Priority
With the field, there is the option to choose, aside from the hard disks connected,
´Bootable add-in Cardsµ which refers to other external devices.
Virus Warning
If this option is enabled, an alarm message will be displayed when trying to write
on the boot sector or on the partition table on the disk, which is typical of the
virus.
CPU L1 / L2 Cache
Cache memory is additional memory that is much faster than conventional
DRAM (system memory). CPUs from 486-type on up contain internal cache
memory, and most, but not all, modern PCs have additional (external) cache
memory. When the CPU requests data, the system transfers the requested data
from the main DRAM into cache memory, for even faster access by the CPU.
These items allow you to enable (speed up memory access) or disable the cache
function. By default, these items are Enabled.
2807700 User’s Manual
29
BIOS SETUP
Hyper-Threading Technology
Hyper-Threading Technology enables two logical processors on a single
physical processor by replicating, partitioning, and sharing the resources
within the Intel NetBurst microarchitecture pipeline.
Quick Power On Self Test
When enabled, this field speeds up the Power On Self Test (POST) after
the system is turned on. If it is set to Enabled, BIOS will skip some
items.
First/Second/Third Boot Device
These fields determine the drive that the system searches first for an
operating system. The options available include LS120, Hard Disk,
CDROM, ZIP100, USB-FDD, USB-ZIP, USB-CDROM and Disabled.
Boot Other Device
These fields allow the system to search for an OS from other devices
other than the ones selected in the First/Second/Third Boot Device.
Boot Up NumLock Status
This allows you to activate the NumLock function after you power up
the system.
Gate A20 Option
This field allows you to select how Gate A20 is worked. Gate A20 is a
device used to address memory above 1 MB.
Typematic Rate Setting
When disabled, continually holding down a key on your keyboard will
generate only one instance. When enabled, you can set the two typematic
controls listed next. By default, this field is set to Disabled.
Typematic Rate (Chars/Sec)
When the typematic rate is enabled, the system registers repeated
keystrokes speeds. Settings are from 6 to 30 characters per second.
Typematic Delay (Msec)
When the typematic rate is enabled, this item allows you to set the time
interval for displaying the first and second characters. By default, this
item is set to 250msec.
30
2807700 User’s Manual
BIOS SETUP
Security Option
This field allows you to limit access to the System and Setup. The default
value is Setup. When you select System, the system prompts for the User
Password every time you boot up. When you select Setup, the system
always boots up and prompts for the Supervisor Password only when the
Setup utility is called up.
APIC Mode
APIC stands for Advanced Programmable Interrupt Controller. The
default setting is Enabled.
MPS Version Control for OS
This option is specifies the MPS (Multiprocessor Specification) version
for the OS. MPS version 1.4 added extended configuration tables to
improve support for multiple PCI bus configurations and improve future
expandability. The default setting is 1.4.
OS Select for DRAM > 64MB
This option allows the system to access greater than 64MB of DRAM
memory when used with OS/2 that depends on certain BIOS calls to
access memory. The default setting is Non-OS/2.
Small Logo (EPA) Show
The EPA logo appears at the right side of the monitor screen when the
system is boot up. The default setting is Disabled.
2807700 User’s Manual
31
BIOS SETUP
Advanced Chipset Features
This Setup menu controls the configuration of the chipset.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced Chipset Features
System BIOS Cacheable
Memory Hole at 15M-16M
PCI Express Root Port Func
Enabled
Disabled
Press Enter
ITEM HELP
Menu Level >
** VGA Setting **
PEG/On Chip VGA Control
On-Chip Frame Buffer Size
DVMT Mode
Auto
8MB
DVMT
128MB
DVMT/FIXED memory Size
System BIOS Cacheable
The setting of Enabled allows caching of the system BIOS ROM at
F000h-FFFFFh, resulting in better system performance. However, if
any program writes to this memory area, a system error may result.
Memory Hole At 15M-16M
In order to improve performance, certain space in memory can be
reserved for ISA cards. This memory must be mapped into the memory
space below 16 MB. The choices are Enabled and Disabled.
On-Chip VGA Setting
The fields under the On-Chip VGA Setting and their default settings are:
PEG/On Chip VGA Control: Auto
On-Chip Frame Buffer Size: 8MB
DVMT Mode: DVMT
DVMT/Fixed Memory Size: 128MB
32
2807700 User’s Manual
BIOS SETUP
Integrated Peripherals
This section sets configurations for your hard disk and other integrated
peripherals. The first screen shows three main items for user to select.
Once an item selected, a submenu appears. Details follow.
Phoenix - AwardBIOS CMOS Setup Utility
Integrated Peripherals
Press Enter
Press Enter
ITEM HELP
OnChip IDE Device
SuperIO Device
Press Enter
Menu Level >
USB Device Setting
Phoenix - AwardBIOS CMOS Setup Utility
OnChip IDE Device
Enabled
Enabled
Auto
Auto
Auto
ITEM HELP
IDE HDD Block Mode
IDE DMA transfer access
IDE Primary Master PIO
IDE Primary Slave PIO
IDE Primary Master UDMA
IDE Primary Slave UDMA
On-Chip Secondary PCI IDE
IDE Secondary Master PIO
Secondary Slave PIO
Secondary Master UDMA
Secondary Slave UDMA
SATA Mode
Menu Level
>
Auto
Enabled
Auto
Auto
Auto
Auto
IDE
IDE
IDE
IDE
LEGACY Mode Support
Enabled
Phoenix - AwardBIOS CMOS Setup Utility
SuperIO Device
ITEM HELP
Menu Level >
POWER ON Function
KB Power ON Password
Hot Key power ON
Onboard Serial Port 1
Onboard Serial Port 2
PWRON After PWR-Fail
BUTTON ONLY
Enter
Ctrl-F1
3F8/IRQ4
2F8/IRQ3
Off
Phoenix - AwardBIOS CMOS Setup Utility
USB Device Setting
Enabled
ITEM HELP
Menu Level >
USB 1.0 Controller
Enabled
Enabled
USB 2.0 Controller
USB Keyboard Function
Enabled
Enabled
USB Mouse Function
USB Storage Function
*** USB Mass Storage Device Boot Setting ***
2807700 User’s Manual
33
BIOS SETUP
IDE HDD Block Mode
This field allows your hard disk controller to use the fast block mode to
transfer data to and from your hard disk drive.
IDE DMA Transfer Access
This field, by default, is enabled
OnChip Secondary PCI IDE
This field, by default, is enabled
IDE Primary/Secondary Master/Slave PIO
These fields allow your system hard disk controller to work faster.
Rather than have the BIOS issue a series of commands that transfer to or
from the disk drive, PIO (Programmed Input/Output) allows the BIOS to
communicate with the controller and CPU directly.
The system supports five modes, numbered from 0 (default) to 4, which
primarily differ in timing. When Auto is selected, the BIOS will select
the best available mode.
IDE Primary/Secondary Master/Slave UDMA
These fields allow your system to improve disk I/O throughput to
33Mb/sec with the Ultra DMA/33 feature. The options are Auto and
Disabled.
SATA Mode
The setting choices for the SATA Mode are IDE, RAID and AHCI
Mode. Select [IDE] if you want to have SATA function as IDE.
Select [AHCI] for Advanced Host Controller Interface (AHCI) feature,
with improved SATA performance with native command queuing &
native hot plug. Select [RAID] to use SATA as RAID function. RAID
function is supported on the board if it uses ICH8R, but this is optional.
LEGACY Mode Support
When the Serial ATA (SATA) is set with the legacy mode enabled, then
the SATA is set to the conventional IDE mode. Legacy mode is
otherwise known as compatible mode.
Power ON Function
This field is related to how the system is powered on – such as with the
use of conventional power button, keyboard or hot keys. The default is
BUTTON ONLY.
34
2807700 User’s Manual
BIOS SETUP
KB Power ON Password
This field allows users to set the password when keyboard power on is
the mode of the Power ON function.
Hot Key Power ON
This field sets certain keys, also known as hot keys, on the keyboard that
can be used as a ‘switch’ to power on the system.
Onboard Serial Port
These fields allow you to select the onboard serial and parallel ports and
their addresses. The default values for these ports are:
Serial Port 1
Serial Port 2
3F8/IRQ4
2F8/IRQ3
PWRON After PWR-Fail
This field sets the system power status whether on or off when power
returns to the system from a power failure situation.
USB 1.0 Controller
The options for this field are Enabled and Disabled. By default, this field
is set to Enabled.
USB 2.0 Controller
The options for this field are Enabled and Disabled. By default, this field
is set to Enabled. In order to use USB 2.0, necessary OS drivers must be
installed first. Please update your system to Windows 2000 SP4 or
Windows XP SP2.
USB Keyboard/Mouse/Storage Function
The options for this field are Enabled and Disabled. By default, this field
is set to Disabled.
2807700 User’s Manual
35
BIOS SETUP
Power Management Setup
Phoenix - AwardBIOS CMOS Setup Utility
Power Management Setup
Enabled
S1(POS)
ITEM HELP
Menu Level
ACPI Function
ACPI Suspend
User Define
Video
V/H SYNC+Blank
>
Power Management
Off Method
Yes
Video Off In Suspend
Stop Grant
3
Suspend Type
Modem Use IRQ
Suspend Mode
Disabled
Disabled
Instant-Off
50.0%
Disabled
0
HDD Power Down
Soft-Off by PWR-BTTN
CPU THRM-Throttling
Resume by Alarm
Date (of Month) Alarm
Time (hh:mm:ss) Alarm
0 : 0 : 0
** Reload Global Timer Events **
Primary IDE 0
Primary IDE 1
Secondary IDE 0
Secondary IDE 1
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
FDD, COM, LPT Port
PCI PIRQ[A-D] #
ACPI Function
Enable this function to support ACPI (Advance Configuration and
Power Interface).
ACPI Suspend
The default setting of the ACPI Suspend mode is S1(POS).
Power Management
This field allows you to select the type of power saving management
modes. There are four selections for Power Management.
Min. Power Saving
Max. Power Saving
User Define
Minimum power management
Maximum power management.
Each of the ranges is from 1 min. to
1hr. Except for HDD Power Down
which ranges from 1 min. to 15 min.
Video Off Method
This field defines the Video Off features. There are three options.
V/H SYNC + Blank
Default setting, blank the screen and turn
off vertical and horizontal scanning.
Allows BIOS to control the video display.
Writes blanks to the video buffer.
DPMS
Blank Screen
36
2807700 User’s Manual
BIOS SETUP
Video Off In Suspend
When enabled, the video is off in suspend mode.
Suspend Type
The default setting for the Suspend Type field is Stop Grant.
Modem Use IRQ
This field sets the IRQ used by the Modem. By default, the setting is 3.
Suspend Mode
When enabled, and after the set time of system inactivity, all devices
except the CPU will be shut off.
HDD Power Down
When enabled, and after the set time of system inactivity, the hard disk
drive will be powered down while all other devices remain active.
Soft-Off by PWRBTN
This field defines the power-off mode when using an ATX power
supply. The Instant Off mode allows powering off immediately upon
pressing the power button. In the Delay 4 Sec mode, the system powers
off when the power button is pressed for more than four seconds or
enters the suspend mode when pressed for less than 4 seconds.
CPU THRM-Throttling
When the system enters Doze mode, the CPU clock runs only part of the
time. You may select the percent of time that the clock runs.
Resume by Alarm
This field enables or disables the resumption of the system operation.
When enabled, the user is allowed to set the Date and Time.
Reload Global Timer Events
The HDD, FDD, COM, LPT Ports, and PCI PIRQ are I/O events that can
prevent the system from entering a power saving mode or can awaken
the system from such a mode. When an I/O device wants to gain the
attention of the operating system, it signals this by causing an IRQ to
occur. When the operating system is ready to respond to the request, it
interrupts itself and performs the service.
2807700 User’s Manual
37
BIOS SETUP
PNP/PCI Configurations
This option configures the PCI bus system. All PCI bus systems on the
system use INT#, thus all installed PCI cards must be set to this value.
Phoenix - AwardBIOS CMOS Setup Utility
PnP/PCI Configurations
PCI Slot
Disabled
ITEM HELP
Menu Level >
Init Display First
Reset Configuration Data
Auto (ESCD)
Press Enter
Resources Controlled By
IRQ Resources
Disabled
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
PCI/VGA Palette Snoop
INT Pin 1 Assignment
INT Pin 2 Assignment
INT Pin 3 Assignment
INT Pin 4 Assignment
INT Pin 5 Assignment
INT Pin 6 Assignment
INT Pin 7 Assignment
INT Pin 8 Assignment
**PCI Express relative items**
Maximum Payload Size
128
Init Display First
The default setting is PCI Card.
Reset Configuration Data
The default value is Disabled.
Resources Controlled by
This PnP BIOS can configure all of the boot and compatible devices
with the use of a PnP operating system such as Windows 95.
PCI/VGA Palette Snoop
Some non-standard VGA display cards may not show colors properly.
This field allows you to set whether or not MPEG ISA/VESA VGA
cards can work with PCI/VGA. When this field is enabled, a PCI/VGA
can work with an MPEG ISA/VESA VGA card. When this field is
disabled, a PCI/VGA cannot work with an MPEG ISA/VESA card.
Maximum Payload Size
The default setting of the PCI Express Maximum Payload Size is 128.
38
2807700 User’s Manual
BIOS SETUP
PC Health Status
Phoenix - AwardBIOS CMOS Setup Utility
PC Health Status
ITEM HELP
Shutdown Temperature
CPU Warning Temperature
Current System Temp
Current CPU Temp
CPU Fan Speed
Disabled
Disabled
32°C/89°F
39°C/102°F
4000 RPM
0 RPM
Menu Level >
Power Fan Speed
Vcore
1.24
V
12
V
12.03 V
1.8 V
1.92
4.99
3.15
V
V
V
5
V
3.3 V
VBAT (V)
5VSB(V)
3.13
5.29
V
V
CPU Warning Temperature
This field allows the user to set the temperature so that when the
temperature is reached, the system sounds a warning. This function can
help prevent damage to the system that is caused by overheating.
Shutdown Temperature
This field allows the user to set the temperature by which the system
automatically shuts down once the threshold temperature is reached.
This function can help prevent damage to the system that is caused by
overheating.
Temperatures/Fan Speeds/Voltages
These fields are the parameters of the hardware monitoring function
feature of the board. The values are read-only values as monitored by the
system and show the PC health status.
2807700 User’s Manual
39
BIOS SETUP
Frequency/Voltage Control
Phoenix - AwardBIOS CMOS Setup Utility
Frequency/Voltage Control
Disabled
Disabled
ITEM HELP
Menu Level >
Auto Detect PCI Clk
Spread Spectrum
Auto Detect PCI Clk
This field enables or disables the auto detection of the PCI clock.
Spread Spectrum
This field sets the value of the spread spectrum. The default setting is
Disabled. This field is for CE testing use only.
40
2807700 User’s Manual
BIOS SETUP
Load Fail-Safe Defaults
This option allows you to load the troubleshooting default values
permanently stored in the BIOS ROM. These default settings are
non-optimal and disable all high-performance features.
Load Optimized Defaults
This option allows you to load the default values to your system
configuration. These default settings are optimal and enable all high
performance features.
Set Supervisor/User Password
These two options set the system password. Supervisor Password sets a
password that will be used to protect the system and Setup utility. User
Password sets a password that will be used exclusively on the system. To
specify a password, highlight the type you want and press <Enter>. The
Enter Password: message prompts on the screen. Type the password, up
to eight characters in length, and press <Enter>. The system confirms
your password by asking you to type it again. After setting a password,
the screen automatically returns to the main screen.
To disable a password, just press the <Enter> key when you are
prompted to enter the password. A message will confirm the password to
be disabled. Once the password is disabled, the system will boot and you
can enter Setup freely.
Save & Exit Setup
This option allows you to determine whether or not to accept the
modifications. If you type “Y”, you will quit the setup utility and save all
changes into the CMOS memory. If you type “N”, you will return to
Setup utility.
Exit Without Saving
Select this option to exit the Setup utility without saving the changes you
have made in this session. Typing “Y” will quit the Setup utility without
saving the modifications. Typing “N” will return you to Setup utility.
2807700 User’s Manual
41
BIOS SETUP
2nd SuperIO Device
The 2nd SuperIO selection under the Integrated Peripherals will appear if
the ID394-R daughter card is used on the motherboard.
Phoenix - AwardBIOS CMOS Setup Utility
Integrated Peripherals
Press Enter
Press Enter
ITEM HELP
OnChip IDE Device
SuperIO Device
2nd SuperIO Device
USB Device Setting
Press Enter
Press Enter
Menu Level
>
Phoenix - AwardBIOS CMOS Setup Utility
2nd SuperIO Device
230h
IRQ11
ITEM HELP
Menu Level >
Onboard Serial Port 3
Serial Port 3 Use IRQ
Onboard Serial Port 4
Serial Port 4 Use IRQ
Onboard Serial Port 5
Serial Port 5 Use IRQ
Onboard Serial Port 6
Serial Port 6 Use IRQ
238h
IRQ10
220h
IRQ11
228h
IRQ10
Onboard Serial Port
These fields allow you to select the onboard serial and parallel ports and
their addresses. The default values for these ports are:
Serial Port 3
Serial Port 4
Serial Port 5
Serial Port 6
230/IRQ11
238/IRQ10
220/IRQ11
228/IRQ10
42
2807700 User’s Manual
BIOS SETUP
Security Chip Configuration
The Security Chip Configuration selection in the BIOS Utility will
appear only if the ID395-R daughter card is used on the motherboard.
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
Advanced BIOS Features
Advanced Chipset Features
Integrated Peripherals
Frequency/Voltage Control
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Security Chip Configuration
Power Management Setup
PnP/PCI Configurations
PC Health Status
Save & Exit Setup
Exit Without Saving
ESC : Quit
Ç È Æ Å : Select Item
F10 : Save & Exit Setup
Time, Date, Hard Disk Type…
Phoenix - AwardBIOS CMOS Setup Utility
Advanced BIOS Features
TPM Support
TPM Current Status
X TPM Status
Disabled
Disabled & Deactivated
No Change
ITEM HELP
Menu Level
Enable/Disable Trusted
Platform Module
>
TPM Support
The default setting is Disabled.
TPM Current Status
The default setting is Disabled & Deactivated.
TPM Status
The default setting is No change.
2807700 User’s Manual
43
BIOS SETUP
This page is intentionally left blank.
44
2807700 User’s Manual
DRIVERS INSTALLATION
Drivers Installation
This section describes the installation procedures for software and
drivers under the Windows 2000 and Windows XP. The software and
drivers are included with the board. If you find the items missing, please
contact the vendor where you made the purchase. The contents of this
section include the following:
Intel Q965 Chipset Software Installation Utility...............46
Intel Q965 Chipset Graphics Driver..................................48
Realtek Codec Audio Driver Installation ..........................50
Intel LAN Drivers Installation ..........................................51
IMPORTANT NOTE:
After installing your Windows operating system (Windows 2000/XP),
you must install first the Intel Chipset Software Installation Utility
before proceeding with the drivers installation.
2807700 User’s Manual
45
DRIVERS INSTALLATION
Intel Q965 Chipset Software Installation Utility
The Intel® Q965 Chipset Drivers should be installed first before the
software drivers to enable Plug & Play INF support for Intel chipset
components. Follow the instructions below to complete the installation
under Windows 2000/XP. (Before installed Intel Chipset Software
Installation Utility,Please update your system to Windows 2000 SP4 or
Windows XP SP1A)
1. Insert the CD that comes with the board and the screen below would
appear. Click Intel (R) Q965 Chipset Drivers, then Intel(R) Chipset
Software Installation Utility.
46
2807700 User’s Manual
DRIVERS INSTALLATION
2. When the Welcome screen appears, click Next to continue.
3. Click Yes to accept the software license agreement and proceed with
the installation process.
4. On the Readme Information screen, click Next to continue the
installation.
5. The Setup process is now complete. Click Finish to restart the
computer and for changes to take effect.
2807700 User’s Manual
47
DRIVERS INSTALLATION
Intel Q965 Chipset Graphics Driver
Follow the instructions below to complete the installation under
Windows 2000/XP.
1. Insert the CD that comes with the board and the screen below would
appear. Click Intel (R) Q965 Chipset Drivers, then Intel (R) Q965
Chipset Family Graphics Driver.
2. When the Welcome screen appears, click Next to continue.
48
2807700 User’s Manual
DRIVERS INSTALLATION
3. Click Yes to accept the software license agreement and proceed with
the installation process.
4. On Readme File Information screen, click Next to continue.
5. On Setup Progress screen, click Next to continue the installation.
6. The Setup process is now complete. Click Finish to restart the
computer and for changes to take effect.
2807700 User’s Manual
49
DRIVERS INSTALLATION
Realtek Codec Audio Driver Installation
1. Insert the CD that comes with the board and the screen below would
appear. Click Intel (R) Q965 Chipset Drivers, then Realtek High
Definition Codec Audio Driver.
2. When the Welcome screen appears, click Next to continue.
3. The Setup process is now complete. Restart the computer when
prompted for changes to take effect.
50
2807700 User’s Manual
DRIVERS INSTALLATION
Intel LAN Drivers Installation
Follow the steps below to start installing the Intel PCI Express Gigabit
LAN drivers.
1. Insert the CD that comes with the board. On the initial screen, Click
Intel (R) Q965 Chipset Drivers, then Intel(R) PRO LAN Network
Drivers.
2. On the next screen, click Install Drivers to start the drivers
installation.
2807700 User’s Manual
51
DRIVERS INSTALLATION
3. When the Welcome screen appears, click Next to continue.
4. In the License Agreement screen, click I accept the terms in license
agreement and Next to accept the software license agreement and
proceed with the installation process.
5. When the Setup Type appears, click Complete and Next to continue.
6. When the Ready to Install the Program screen appears, click Install to
continue.
7. The Setup process is now complete (InstallShield Wizard Completed).
Click Finish to restart the computer and for changes to take effect.
52
2807700 User’s Manual
DRIVERS INSTALLATION
Follow the steps below to install the Marvell Gigabit LAN drivers.
1. Insert the CD that comes with the motherboard. Click LAN Card and
then Marvell LAN Controller Drivers.
2. Click Next when the InstallShield Wizard welcome screen appears.
3. Click Next to agree with the license agreement.
4. Click Next when the Readme Information screen appears to proceed
with the drives installation process.
5. When the Installation is complete, click Finish for the changes to take
effect.
2807700 User’s Manual
53
DRIVERS INSTALLATION
This Page is Intentionally Left Blank.
54
2807700 User’s Manual
APPENDIX
Appendix
A. I/O Port Address Map
Each peripheral device in the system is assigned a set of I/O port
addresses that also becomes the identity of the device. The following
table lists the I/O port addresses used.
Address
Device Description
DMA Controller #1
Interrupt Controller #1
Timer
Keyboard Controller
Real Time Clock, NMI
DMA Page Register
Interrupt Controller #2
DMA Controller #2
Clear Math Coprocessor Busy Signal
Reset Math Coprocessor
IDE Interface
Parallel Port #2(LPT2)
Serial Port #2(COM2)
Graphics adapter Controller
Parallel Port #1(LPT1)
Network Ports
000h - 01Fh
020h - 03Fh
040h - 05Fh
060h - 06Fh
070h - 07Fh
080h - 09Fh
0A0h - 0BFh
0C0h - 0DFh
0F0h
0F1h
1F0h - 1F7h
278h - 27Fh
2F8h - 2FFh
2B0h - 2DFh
378h - 3FFh
360h - 36Fh
3B0h - 3BFh
3C0h - 3CFh
3D0h - 3DFh
3F0h - 3F7h
3F8h - 3FFh
Monochrome & Printer adapter
EGA adapter
CGA adapter
Floppy Disk Controller
Serial Port #1(COM1)
2807700 User’s Manual
55
APPENDIX
B. Interrupt Request Lines (IRQ)
Peripheral devices use interrupt request lines to notify CPU for the
service required. The following table shows the IRQ used by the devices
on board.
Level
IRQ0
IRQ1
IRQ2
IRQ3
IRQ4
IRQ5
IRQ6
IRQ7
IRQ8
IRQ9
IRQ10
IRQ11
IRQ12
IRQ13
IRQ14
IRQ15
Function
System Timer Output
Keyboard
Interrupt Cascade
Serial Port #2
Serial Port #1
Reserved
Floppy Disk Controller
Parallel Port #1
Real Time Clock
Reserved
Reserved
Reserved
PS/2 Mouse
80287
Primary IDE
Secondary IDE
56
2807700 User’s Manual
APPENDIX
C. Watchdog Timer Configuration
The WDT is used to generate a variety of output signals after a user
programmable count. The WDT is suitable for use in the prevention of
system lock-up, such as when software becomes trapped in a deadlock.
Under these sorts of circumstances, the timer will count to zero and the
selected outputs will be driven. Under normal circumstance, the user will
restart the WDT at regular intervals before the timer counts to zero.
SAMPLE CODE:
//=======================================================================
//
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
// PURPOSE.
//
//=======================================================================
====
#include <stdio.h>
#include <stdlib.h>
#include "W627EHF.H"
//=======================================================================
====
int main (int argc, char *argv[]);
void copyright(void);
void EnableWDT(int);
void DisableWDT(void);
//=======================================================================
====
int main (int argc, char *argv[])
{
unsigned char bBuf;
unsigned char bTime;
char **endptr;
copyright();
if (argc != 2)
{
printf(" Parameter incorrect!!\n");
return 1;
}
if (Init_W627EHF() == 0)
{
printf(" Winbond 83627HF is not detected, program abort.\n");
return 1;
}
bTime = strtol (argv[1], endptr, 10);
2807700 User’s Manual
57
APPENDIX
printf("Systemwill reset after %d seconds\n", bTime);
EnableWDT(bTime);
return 0;
}
//=======================================================================
void copyright(void)
{
printf("\n======== Winbond 83627EHF Watch Timer Tester (AUTO DETECT)
========\n"\
"
"
"
Usage : W627E_WD reset_time\n"\
Ex : W627E_WD 3 => reset system after 3 second\n"\
W627E_WD 0 => disable watch dog timer\n");
}
//=======================================================================
void EnableWDT(int interval)
{
unsigned char bBuf;
bBuf = Get_W627EHF_Reg( 0x2D);
bBuf &= (!0x01);
Set_W627EHF_Reg( 0x2D, bBuf);
//Enable WDTO
Set_W627EHF_LD( 0x08);
Set_W627EHF_Reg( 0x30, 0x01);
//switch to logic device 8
//enable timer
bBuf = Get_W627EHF_Reg( 0xF5);
bBuf &= (!0x08);
Set_W627EHF_Reg( 0xF5, bBuf);
//count mode is second
Set_W627EHF_Reg( 0xF6, interval);
//set timer
}
//=======================================================================
void DisableWDT(void)
{
Set_W627EHF_LD(0x08);
Set_W627EHF_Reg(0xF6, 0x00);
Set_W627EHF_Reg(0x30, 0x00);
//switch to logic device 8
//clear watchdog timer
//watchdog disabled
}
//=======================================================================
58
2807700 User’s Manual
APPENDIX
//=======================================================================
//
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
// PURPOSE.
//
//=======================================================================
====
#include "W627EHF.H"
#include <dos.h>
//=======================================================================
====
unsigned int W627EHF_BASE;
void Unlock_W627EHF (void);
void Lock_W627EHF (void);
//=======================================================================
unsigned int Init_W627EHF(void)
{
unsigned int result;
unsigned char ucDid;
W627EHF_BASE = 0x2E;
result = W627EHF_BASE;
ucDid = Get_W627EHF_Reg(0x20);
if (ucDid == 0x88)
{
goto Init_Finish;
}
W627EHF_BASE = 0x4E;
result = W627EHF_BASE;
ucDid = Get_W627EHF_Reg(0x20);
if (ucDid == 0x88)
{
goto Init_Finish;
}
W627EHF_BASE = 0x00;
result = W627EHF_BASE;
Init_Finish:
return (result);
}
//=======================================================================
void Unlock_W627EHF (void)
{
outportb(W627EHF_INDEX_PORT, W627EHF_UNLOCK);
outportb(W627EHF_INDEX_PORT, W627EHF_UNLOCK);
}
//=======================================================================
====
void Lock_W627EHF (void)
{
outportb(W627EHF_INDEX_PORT, W627EHF_LOCK);
}
//=======================================================================
void Set_W627EHF_LD( unsigned char LD)
{
Unlock_W627EHF();
outportb(W627EHF_INDEX_PORT, W627EHF_REG_LD);
outportb(W627EHF_DATA_PORT, LD);
2807700 User’s Manual
59
APPENDIX
Lock_W627EHF();
}
//=======================================================================
void Set_W627EHF_Reg( unsigned char REG, unsigned char DATA)
{
Unlock_W627EHF();
outportb(W627EHF_INDEX_PORT, REG);
outportb(W627EHF_DATA_PORT, DATA);
Lock_W627EHF();
}
//=======================================================================
unsigned char Get_W627EHF_Reg(unsigned char REG)
{
unsigned char Result;
Unlock_W627EHF();
outportb(W627EHF_INDEX_PORT, REG);
Result = inportb(W627EHF_DATA_PORT);
Lock_W627EHF();
return Result;
}
//=======================================================================
//=======================================================================
//
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
// PURPOSE.
//
//=======================================================================
#ifndef __W627EHF_H
#define __W627EHF_H
1
//=======================================================================
#define
#define
W627EHF_INDEX_PORT
W627EHF_DATA_PORT
(W627EHF_BASE)
(W627EHF_BASE+1)
//=======================================================================
#define W627EHF_REG_LD 0x07
//=======================================================================
#define W627EHF_UNLOCK
#define W627EHF_LOCK
0x87
0xAA
//=======================================================================
unsigned int Init_W627EHF(void);
void Set_W627EHF_LD( unsigned char);
void Set_W627EHF_Reg( unsigned char, unsigned char);
unsigned char Get_W627EHF_Reg( unsigned char);
//=======================================================================
#endif
//__W627EHF_H
60
2807700 User’s Manual
APPENDIX
File of the Main.cpp
//=====================================================================
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
// PURPOSE.
//=====================================================================
#include <dos.h>
#include <conio.h>
#include <stdio.h>
#include <stdlib.h>
#include "W627HF.H"
//=====================================================================
void ClrKbBuf(void);
int main (int argc, char *argv[]);
//=====================================================================
int main (int argc, char *argv[])
{
unsigned char ucDO = 0;
unsigned char ucDI;
unsigned char ucBuf;
//data for digital output
//data for digital input
Set_W627HF_LD( 0x07);
//switch to logic device 7
//clear
Set_W627HF_Reg(0xF1, 0x00);
ucDI = Get_W627HF_Reg(0xF1) & 0x0F;
ClrKbBuf();
while(1)
{
ucDO++;
Set_W627HF_Reg(0xF1, ((ucDO & 0x0F) << 4));
ucBuf = Get_W627HF_Reg(0xF1) & 0x0F;
if (ucBuf != ucDI)
{
ucDI = ucBuf;
printf("Digital I/O Input Changed. Current Data is 0x%X\n",ucDI);
}
if (kbhit())
{
getch();
break;
}
delay(500);
return 0;
}
}
//=====================================================================
void ClrKbBuf(void)
{
while(kbhit())
{
getch();
}
}
//---------------------------------------------------------------------------
2807700 User’s Manual
61
CONTACT INFORMATION
Any advice or comments about our products and
service, or anything we can help you with please don’t
hesitate to contact with us. We will do our best to
support you for your products, projects and business.
Global American Inc.
Address:
17 Hampshire Drive
Hudson, NH 03051
TEL:
Toll Free (U.S. Only) 800-833-8999
(603)886-3900
FAX:
(603)886-4545
Website:
E-Mail:
62
2807700 User’s Manual
|