GE General Electric Cooktop JP930 User Manual

Installation 30Electric Cooktop  
JP340, JP355, JP910, JP930, JP940, JP950  
Instructions  
“If you have questions, call 800.GE.CARES or visit our website at:  
www.GEAppliances.com”  
BEFORE YOU BEGIN  
MATERIALS YOU WILL NEED  
Read these instructions completely  
and carefully.  
IMPORTANT Save these  
instructions for local inspector’s use.  
Wire Nuts  
Junction Box  
IMPORTANT Observe all  
governing codes and ordinances.  
Note to Installer – Be sure to leave these  
TOOLS YOU WILL NEED  
instructions with the Consumer.  
Note to Consumer – Keep these  
instructions for future reference.  
Pencil  
Product failure due to improper installation  
is not covered under the Warranty.  
Saber Saw  
WARNING This appliance must  
Phillips Head  
Screwdriver  
be properly grounded.  
ATTENTION INSTALLER —  
ALL COOKTOPS MUST BE HARD WIRED  
(DIRECT WIRED) INTO AN APPROVED  
JUNCTION BOX. A “PLUG AND  
1/8Drill Bit & Electric  
or Hand Drill  
Ruler or Straightedge  
Safety Glasses  
RECEPTACLE” IS NOT PERMITTED ON  
THESE PRODUCTS.  
Proper installation is the responsibility  
of the installer and product failure due to  
improper installation is NOT covered under  
warranty.  
PARTS INCLUDED  
2 Hold Down  
Brackets  
4 Screws  
Foam Tape  
31-10603 (12-04 JR)  
1
Installation Instructions  
PRE-INSTALLATION CHECKLIST  
Remove Installation Instructions from  
literature pack and read them carefully  
before you begin.  
3
WARNING – The electrical power  
to the cooktop supply line must be shut off  
while connections are being made. Failure to  
do so could result in serious injury or death.  
Be sure to place all literature, Owner’s  
Manual, Installations, etc. in a safe place  
for future reference.  
When preparing cooktop opening, make  
sure the inside of the cabinet and the  
cooktop do not interfere with each other.  
(See section on preparing the opening.)  
1
Before you begin-Read these instructions completely and carefully.  
IMPORTANT- Save these instructions for local inspector's use.  
IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.  
Note to Installer- Be sure to leave these instructions with the consumer.  
OWNER- Keep these instructions for future reference.  
Note- This appliance must be properly grounded (iapplicable).  
Remove packaging materials and  
literature package from the cooktop  
before beginning installation.  
2
Literature  
Package  
Make sure you have all the tools and  
materials you need before starting the  
installation of the cooktop.  
4
5
Styrofoam  
Packaging  
Your home must provide the adequate  
electrical service needed to safely and  
properly use your cooktop. (Refer to  
section on electrical requirements.)  
ON  
When installing your cooktop in your  
home, make sure all local codes and  
ordinances are followed exactly as  
stated.  
6
7
Cooktop  
Make sure the wall coverings, countertop  
and cabinets around the cooktop can  
withstand heat (up to 200°F) generated  
by the cooktop.  
3
Installation Instructions  
PREPARING THE OPENING  
The following MINIMUM clearance  
dimensions must be maintained.  
CUTOUT DIMENSIONS  
OF THE COUNTERTOP  
To insure accuracy, it is best to make a  
template when cutting the opening in  
the counter.  
1
4
13MAX. Depth of uprotected  
1-1/2MIN.  
overhead cabinets  
Clearance from  
cutout to side  
wall on the right  
of the unit  
19-5/8width of cut  
30MIN.  
28-1/2″  
length of  
cut  
Clearance from  
countertop to  
unprotected  
overhead  
18MIN. Height  
from countertop  
to nearest  
cabinet on either  
side of unit  
1-3/4Min. Between  
cutout and the wall  
behind the cooktop  
surface  
2-1/2Min.  
from front edge  
of cutout and  
front edge of  
countertop  
2MIN. Clearance  
from cutout to  
side wall on the  
left of the unit  
JXTR32X CUTOUT FILLER TRIM KIT:  
A filler trim kit is available for use if  
your countertop cutout is larger than the  
dimensions shown, up to 29-13/16x  
20-7/16. Order JXTR32X to reduce the cutout  
opening for installation of this cooktop. This  
kit may be ordered from your GE Dealer.  
If a 30clearance between the cooking  
surface and overhead combustible materials  
or metal cabinets cannot be maintained, a  
minimum clearance of 24is required and  
the underside of the cabinets above the  
cooktop must be protected with not less  
than 1/4insulating millboard covered with  
sheet metal not less than 0.0122thick.  
JXFLM2XX FLUSH INSTALLATION KIT:  
A flush mount installation kit is available  
for use in a flush mount or recessed cooktop  
installation. Order JXFLM2XX from your  
GE Dealer.  
OVERALL COOKTOP  
DIMENSIONS  
2
20-7/8(21-1/2Max. on  
Curved Front Models)  
29-3/4″  
Cooktop  
Make sure the wall coverings, countertop  
and cabinets around the cooktop can  
withstand heat (up to 200°F) generated  
by cooktop.  
5
3-1/4Front  
4-5/8Rear  
at the conduit  
location  
6-1/4Rear on  
28″  
19-1/4″  
Model JP950  
Wall covering,  
cabinets and  
countertop must  
withstand heat  
up to 200°F.  
Five inches (5)  
3
minimum vertical  
clearance between  
the cooktop bottom  
and any combustible  
surfaces.  
5Min.  
Vertical Clearance  
4
Installation Instructions  
INSTALLING THE COOKTOP  
INSTALLING THE  
JUNCTION BOX  
Install an approved junction box where it will  
be easily reached through the front of the  
cabinet where the cooktop will be located.  
The cooktop conduit is 3 feet long.  
ATTACH FOAM TAPE  
1
3
Apply the foam tape around the outer edge  
of the glass. Do not overlap the foam tape.  
Bottom of Cooktop  
Foam Tape  
Cooktop  
Glass  
16″  
Min.  
LOCATE MOUNTING PARTS  
4
Install junction box so  
that it can be reached  
through the front of  
the cabinet.  
Remove the hold down brackets and screws  
from the literature package.  
Mounting Screw  
ATTACH BRACKETS  
TO COOKTOP  
Screw the hold down bracket to the side  
of the cooktop unit. Repeat for opposite side  
of cooktop.  
5
IMPORTANT: The junction box  
must be located where it will allow  
considerable slack in the conduit for  
serviceability.  
PROTECT SURFACE  
OF COOKTOP  
Place a towel or tablecloth onto the  
countertop. Lay the cooktop upside down  
onto the protected surface.  
2
Pre-Drilled Hole  
Bottom of Cooktop  
Foam Tape  
Hold Down  
Bracket  
Bottom of Cooktop  
Cooktop Glass  
Cloth under Cooktop  
5
Installation Instructions  
INSTALLING THE COOKTOP (CONT.)  
INSERT COOKTOP  
INTO CUTOUT  
Insert the cooktop centered into the cutout  
opening. Make sure the front edge of the  
countertop is parallel to the cooktop. Make  
final check that all required clearances  
are met.  
ATTACH HOLD DOWN  
BRACKETS TO CABINET  
Open the cabinet door and screw the hold  
down brackets to the cabinet sides with the  
screws provided.  
6
7
Burner Box Sides  
Mounting Screw  
Cooktop  
Hold Down  
Bracket  
Use suitable fasteners  
for anchorage in  
cabinet sides  
Cabinet Side  
6
Installation Instructions  
INSTALLATION—ELECTRICAL CONNECTIONS  
When making the wire connections, use  
the entire length of conduit provided.  
The conduit must not be shortened.  
Once the connections are made, secure  
wires together using wire nuts.  
A
E
Red  
With the cooktop in place, open the front  
of the cabinet door.  
B
C
Strain Relief Clamp  
Insert the wires from the conduit through  
the opening of the junction box.  
Black  
Ground  
GROUNDING INSTRUCTIONS:  
Red  
Strain Relief Clamp  
The bare ground wire in the conduit is  
connected to the cooktop frame. Effective  
January 1, 1996, the National Electrical Code  
will not permit grounding through neutral.  
If used in new construction after January 1, 1996  
or in a mobile home, recreational vehicle or  
if local codes do not permit grounding  
through the neutral white lead, attach the  
appliance grounding lead (green or copper)  
to the residence grounding conductor (green  
or bare copper) in accordance with local  
codes. When connecting to a 3 conductor  
branch circuit, if local codes permit, connect  
the bare ground connector lead of the  
cooktop to the branch circuit neutral (gray  
or white in color).  
Ground  
Black  
Connect the red and black leads from the  
cooktop conduit to the corresponding  
leads in the junction box.  
D
Red  
Ground wire  
location  
Black  
IMPORTANT: If the cooktop is  
being installed into a blind counter (one with  
no cabinet opening below), wire connections  
must be made before putting the cooktop  
into the cutout opening.  
7
Installation Instructions  
CHECKLISTS  
PRE-TEST CHECKLIST  
OPERATION CHECKLIST  
1
2
Remove all protective film, if present,  
and any stickers.  
Remove all items from the top  
of the cooktop surface.  
A
A
Check to be sure that all wiring is secure  
and not pinched or in contact with  
moving parts.  
Turn on the power to the cooktop.  
(Refer to your Owner’s Manual.) Verify  
that all surface burners operate properly.  
B
B
Check level of appliance.  
Check that the circuit breaker is not  
tripped nor the house fuse blown.  
C
D
C
D
E
Check that the cooktop is properly  
grounded.  
Check that conduit is securely connected  
to the junction box.  
See Owner’s Manual for  
troubleshooting list.  
NOTE TO ELECTRICIAN:  
The power leads supplied with this appliance  
are UL recognized for connections to larger  
gauge household wiring. The insulation of  
these leads is rated at temperatures much  
higher than the temperature rating of  
household wiring. The current carrying  
capacity of a conductor is governed by the  
wire gauge and also the temperature rating  
of the insulation around the wire.  
NOTE: ALUMINUM WIRING  
WARNING:  
IMPROPER CONNECTION OF ALUMINUM  
HOUSE WIRING TO THE COPPER LEADS  
CAN RESULT IN A SERIOUS PROBLEM.  
Splice copper wires to aluminum wiring  
using special connectors designed and  
UL approved for joining copper to  
aluminum and follow the manufacturer’s  
recommended connector procedure  
closely.  
NOTE: Wire used, location and enclosure of  
splices, etc., must conform to good wiring  
practice and local codes.  
8

GE Monogram ZET1P User Manual
GE 16197920 User Manual
Fujitsu Computer Monitor D556Q User Manual
Dell S2009W User Manual
Cypress CY7C107BN User Manual
Coleman FYRESTORM 9770 User Manual
Carrier 38EV036320 User Manual
Asus PP DLW User Manual
Ariston PF750AST User Manual
Aiphone Conference Phone LE DA User Manual