PRIMERGY
System Board D2630
for RX600 S3 SAS
Technical manual
E. Hübner-Hatzel
Fujitsu Siemens Computers GmbH Paderborn
33094 Paderborn
e-mail: email: [email protected]
Tel.: 05251 / 14888-13
Fax: (++49) 700 / 372 00001
D2630 (RX600 S3) SAS
Sprachen: En
Edition January 2007
Contents
1
2
2.1
2.2
2.3
Notes on safety . . . . . . . . . . . . . . . . . . . . . . . . . 3
CE Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Environment Protection . . . . . . . . . . . . . . . . . . . . . 7
3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.1
3.2
3.3
3.4
3.5
Main memory . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Screen resolution . . . . . . . . . . . . . . . . . . . . . . . 16
3.6
3.6.1
Connectors and jumpers . . . . . . . . . . . . . . . . . . . 18
External connectors . . . . . . . . . . . . . . . . . . . . . . . 20
3.7
3.8
RoMB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Replacing the RAID Controller . . . . . . . . . . . . . . . . 22
4
Replacing the lithium battery . . . . . . . . . . . . . . . . . 29
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
D2630 (RX600 S3) SAS
1
Introduction
This technical manual describes the system board D2630, which can be
equipped with up to four Intel® processors.
Further information about drivers is provided in the readme files on the supplied
ServerSupport or ServerStart CDs.
You will find further information in the manual "D2630 Setup Utility".
Notational conventions
The meanings of the symbols and fonts used in this manual are as follows:
italics
indicates commands, menu items, file and path
names or software programs
fixed font
indicates system output on the monitor
semi-bold fixed
font
indicates values to be entered through the keyboard
[Key symbol]
indicates keys according to their representation on the
keyboard
If capital letters are to be entered explicitly, then the
Shift key is shown, e.g. [SHIFT] - [A] for A.
If two keys need to be pressed at the same time, then
this is shown by placing a hyphen between the two key
symbols.
“quotation marks”
indicates names and terms that are being empha-
sized.
Ê
indicates an operation that to be performed
V
I
CAUTION!
indicates warnings, which, if ignored, will endanger
your health, destroy the system or lead to the loss of
data.
indicates additional information, notes and tips
Table 1: Notational conventions
D2630 (RX600 S3) SAS
1
2
Important notes
In this chapter you will find essential information regarding safety when working
with the system board.
V
CAUTION!
With the system board installed you must open the system to access the
system board. How to dismantle and reassemble the system is described
in the Options Guide accompanying your system.
2.1
Notes on safety
V
CAUTION!
●
The actions described in these instructions should only be performed
by authorized, qualified personnel. Equipment repairs should only be
performed by qualified staff. Any failure to observe the guidelines in
this manual, and any unauthorized openings and improper repairs
could expose the user to risks (electric shock, fire hazards) and could
also damage the equipment. Please note that any unauthorized
openings of the device will result in the invalidation of the warranty
and exclusion from all liability.
●
●
Transport the device only in the antistatic original packaging or in
packaging that protects it from knocks and jolts.
Only install expansions that are allowed for the system board. If you
install other expansions, you may damage the requirements and rules
governing safety and electromagnetic compatibility or your system.
Information on which system expansions are suitable can be
obtained from the customer service centre or your sales outlet.
●
The warranty expires if the device is damaged during the installation
or replacement of system expansions.
D2630 (RX600 S3) SAS
3
Notes on safety
Important notes
V
●
Components can become very hot during operation. Ensure you do
not touch components when making extensions to the system board.
There is a danger of burns!
●
●
Transmisson lines to peripheral devices must be adequately shielded.
To the LAN wiring the requirements apply in accordance with the
standards EN 50173 and EN 50174-1/2. As minimum requirement
the use of a protected LAN line of category 5 for 10/100 MBps
Ethernet, and/or of category 5e for Gigabit Ethernet is considered.
The requirements of the specification ISO/IEC 11801 are to be
considered.
●
(lightning hazard).
Batteries
V
CAUTION!
●
Incorrect replacement of the lithium battery may lead to a risk of
explosion. The batteries may only be replaced with identical batteries
or with a type recommended by the manufacturer.
It is essential to observe the instructions in chapter “Replacing the
lithium battery” on page 29.
●
●
●
Do not throw batteries into the trash can. They must be disposed of
in accordance with local regulations concerning special waste.
The battery must be disposed of in accordance with local regulations
concerning special waste.
All batteries containing pollutants are marked with a symbol (a
crossed-out garbage can). In addition, the marking is provided with
the chemical symbol of the heavy metal decisive for the classification
as a pollutant:
Cd Cadmium
Hg Mercury
Pb Lead
4
D2630 (RX600 S3) SAS
Important notes
Notes on safety
Modules with electrostatic-sensitive components
Systems and components that might be damaged by electrostatic discharge
(ESD) are marked with the following label:
Figure 1: ESD label
When you handle components fitted with ESDs, you must observe the following
points under all circumstances:
●
You must always discharge yourself of static charges (e.g. by touching a
grounded object) before working.
●
●
The equipment and tools you use must be free of static charges.
Remove the power plug from the power socket before inserting or removing
boards containing ESDs.
●
●
●
Always hold boards with ESDs by their edges.
Never touch pins or conductors on boards fitted with ESDs.
Use a grounding cable designed for this purpose to connect yourself to the
system unit as you install/deinstall the board.
●
Place all components on a static-safe base.
I
You will find a detailed description for handling ESD components in the
relevant European or international standards (EN 61340-5-1,
ANSI/ESD S20.20).
D2630 (RX600 S3) SAS
5
CE Certificate
Important notes
Notes about boards
●
●
●
During installation/deinstallation of the system board, observe the specific
instructions described in the service manual for the server.
Remove the plug from the mains outlet so that system and system board are
totally disconnected from the mains voltage.
To prevent damage to the system board, the components and conductors on
it, please take great care when you insert or remove boards. Take great care
to ensure that extension boards are slotted in straight, without damaging
components or conductors on the system board, or any other components,
for example EMI spring contacts
●
●
Be careful with the locking mechanisms (catches, centring pins etc.) when
you replace the system board or components on it, for example memory
modules or processors.
Never use sharp objects (screwdrivers) for leverage.
2.2
CE Certificate
The shipped version of this board complies with the requirements
of the EEC directive 89/336/EEC "Electromagnetic compatibility".
Compliance was tested in a typical PRIMERGY configuration.
6
D2630 (RX600 S3) SAS
Important notes
Environment Protection
2.3
Environment Protection
Environmentally-friendly product design and development
This product has been designed in accordance with the Fujitsu Siemens
Computers standard for “environmentally friendly product design and devel-
opment”. This means that key factors such as durability, selection and labeling
of materials, emissions, packaging, ease of disassembly and recycling have
been taken into account.
This saves resources and thus reduces the harm done to the environment.
Notes on saving energy
Devices that do not have to be on permanently should not be switched on until
they need to be used and should be switched off during long breaks and on
completion of work
Notes on packaging
Please do not throw away the packaging. You may need it later for transporting
your system unit. If possible, the device should only be transported in its original
packaging.
Notes on dealing with consumables
Please dispose batteries in accordance with local government regulations.
Do not throw lithium batteries into the household waste. They must be disposed
of in accordance with local regulations concerning special waste.
Notes on labeling plastic housing parts
Please avoid attaching your own labels to plastic housing parts wherever
possible, since this makes it difficult to recycle them.
D2630 (RX600 S3) SAS
7
Environment Protection
Important notes
Returning used electrical and electronic devices in EU countries
–
Separate collection
Users of electrical and electronic devices are obligated to collect used
devices separately. Electrical (electronic) used devices may not be disposed
of together with unsorted household refuse. The separate collection is a
condition for reuse, recycling and utilisation of used electrical (electronic)
devices, which ensures the protection of resources.
–
Return and collection systems
Electrical (electronic) used devices from private households can be returned
free of charge. To return your used device, please use the country-specific
return and collection systems available to you (see “Local contacts” on
page 9).
The return of used devices which pose a health or safety risk for human
beings due to soiling during use may be refused.
–
–
Reuse, recycling and utilisation
By actively using the offered return and collection systems, you make your
contribution to the reuse, recycling and utilisation of electrical (electronic)
devices.
Effects on the environment and human health
Electrical (electronic) used devices contain parts which must be handled
selectively according to the EU directive. Separate collection and selective
treatment are the basis for environment-friendly disposal and the protection
of human health.
–
Meaning of the symbol "Crossed out rubbish bin on wheels"
Electrical (electronic) devices which are marked with one of the following
symbols may not be disposed of with household refuse in accordance with
the EU directive.
Figure 2: Symbols for electrical (electronic) devices
8
D2630 (RX600 S3) SAS
Important notes
Environment Protection
Returning batteries
Batteries which are marked with one of the following symbols may not be
disposed of together with household refuse according to the applicable EU
directive.
Figure 3: Symbols for batteries
With batteries containing harmful substances, the chemical symbol for the
heavy metal contained is indicated below the waste bin.
Cd Cadmium
Hg Mercury
Pb Lead
The following applies to Germany:
–
Private consumers can return batteries at the point of sale or the immediate
vicinity thereof free of charge (exception: starter batteries).
–
The final consumer is obligated to return defective or used batteries to the
seller or to the return points established for this purpose.
Local contacts
For details on take-back and reuse of devices and consumables within Europe,
contact your Fujitsu Siemens Computers branch office/subsidiary or our
recycling center in Paderborn:
Fujitsu Siemens Computers
Recycling Center
D-33106 Paderborn
Germany
Tel. +49 5251 8 18010
Fax +49 5251 8 18015
D2630 (RX600 S3) SAS
9
3
Features
3.1
Overview
System board
●
Up to four Intel® XEON MP dual-core processors
Intel® E8501 chipset:
●
–
Intel® E8501 chipset Northbridge (TNB): has two shared 64-bit FSB
interfaces configured for symmetric multiprocessing.
–
–
–
External Memory Board (XMB): provides support for DDR-2 memory.
PXH: provides support for PCI-X .
Intel® IOP333 I/O processor with Intel XScale® Microarchitecture:
provides support for PCI-X and contains Intel XScale® technology to
support RoMB (RAID on Motherboard).
–
Intel® 82801EB I/O controller Hub 5 (Southbridge) provides support for
system BIOS, USB 2.0 and SATA.
●
Advanced I/O architecture:
–
–
–
–
One hot-plug x8 PCI-Express slot
Three hot-plug x4 PCI-Express slots
One hot-plug 133 MHz, 64-bit PCI-X slot
Two 100 MHz, 64-bit PCI-X slots (not hot-plug)
●
●
LSI Logic® 53C1030 LVD SCSI controller:
–
–
Dual independent U320 SCSI interfaces
64-bit PCI-X 100 Mhz interface
Integrated ATI Technologies Inc® Radeon 7000M with 16 MB embedded
SDRAM
D2630 (RX600 S3) SAS
11
Overview
Features
●
USB 2.0 support:
–
–
–
Two ports at the rear of the chassis
Three ports at the front of the chassis
One port onboard
Main memory
–
Up to 4 hot-plug memory boards with each 4 slots for main memory PC2-
3200 DDRII/400 MHz, DIMM memory modules with 1 Gbyte, 2 Gbyte and
4 Gbyte
–
–
–
–
Maximum 64 Gbyte of memory
Memory mirroring function or memory RAID
Optional hot-spare memory function
Single Device Data Correction (SDDC) function (Chipkill™)
External connectors
–
Front side (front panel):
3x USB 2.0 ports
1x VGA port (15 pin)
–
Rear side (I/O shield):
2x USB 2.0 ports
1x VGA port (15 pin)
1x RS-232-C interface (serial 9 pin)
2x RJ45 LAN ports (onboard LAN)
1x RJ45 LAN port (presently not used, reserved for future development)
BIOS features
–
–
–
–
–
–
Intel® Platform Innovation Framework EFI BIOS
MultiProcessor Specification 1.4
Server Hardware Design Guide 3.0
WfM 2.0
IPMI V1.5
ACPI 1.0b support
12
D2630 (RX600 S3) SAS
Features
Overview
–
–
–
–
–
Intel® RoMB BIOS
LSI SCSI BIOS
SATA support
USB keyboard/mouse
boot possible from:
–
–
–
–
CD/DVD-ROM
USB drive
LAN
hard disk
–
–
–
–
console redirection support
OEM logo
CPU, Memory disable
memory mirroring/RAID/spare support
Environmental protection
Battery in holder
Form factor
16.4“ x 18.3“
D2630 (RX600 S3) SAS
13
Main memory
Features
3.2
Main memory
The system board offers four slots for hot-plug memory boards. Each memory
board can be equipped with up to four memory modules (in two memory banks).
The slots for main memory can be populated with 1 Gbyte, 2 Gbyte or 4 Gbyte
DDR II/400 MHz DIMM memory modules. The maximum memory is 64 Gbyte.
ECC with memory scrubbing and with the Single Device Data Correction
(SDDC) function is supported.
I
You will find the descriptions how to install a memory board in the
Operating Manual of your server and how to install memory modules in
the Opttion Guide of your server.
Memory board population
DIMM 1B
DIMM 1A
DIMM 2B
DIMM 2A
Figure 4: Memory board population
–
–
Start with memory bank 1 (DIMM1A/DIMM1B).
Install the memory modules in pairs. All DIMMs in a pair must be of the same
type and size.
–
The module capacity between pairs can differ: pair 2A/2B can be populated
with two 1 Gbyte modules and pair 1A/1B with two 2 Gbyte modules.
14
D2630 (RX600 S3) SAS
Features
PCI bus
3.3
PCI bus
1
2
3
4
5
6
7
Figure 5: PCI slots
PCI slots
The following table shows an overview of the PCI slots:
PCI slot
Transfer rate
2500 Mbyte/s
1064 Mbyte/s
1250 Mbyte/s
1250 Mbyte/s
1250 Mbyte/s
800 Mbyte/s
800 Mbyte/s
Description
Hot-plug
yes
1
2
3
4
5
6
7
PCI-Express x8 slot
PCI-X bus slot (133 MHz) yes
PCI-Express x4 slot
PCI-Express x4 slot
PCI-Express x4 slot
yes
yes
yes
PCI-X bus slot (100MHz) no
PCI-X bus slot (100MHz) no
Assignment of the PCI interrupts
The PCI interrupts are assigned automatically by the BIOS and no further
settings are possible.
D2630 (RX600 S3) SAS
15
Screen resolution
Features
3.4
Screen resolution
Depending on the operating system used the screen resolutions in the following
table refer to the screen controller on the system board. If you are using an
external screen controller, you will find details of supported screen resolutions
in the operating manual or technical manual supplied with the controller.
Screen resolution Refresh rate
(Hz)
Digital Display Max. number of colours
(Hz)
640x480
200
200
200
150
130
90
75
75
75
-
16,7 Mio.
16,7 Mio.
16,7 Mio.
16,7 Mio.
16,7 Mio.
16,7 Mio.
800x600
1024x768
1152x864
1280x1024
1600x1200
75
60
3.5
Temperature / system monitoring
Temperature and system monitoring aim to reliably protect the computer
hardware against damage caused by overheating. In addition, any unnecessary
noise is also prevented by reducing the fan speed, and information is provided
about the system status.
The temperature and system monitoring are controlled by an onboard controller.
The following functions are supported:
Temperature monitoring
Measurement of the processor temperature, measurement of the ambient
temperature by a temperature sensor on the LED board.
16
D2630 (RX600 S3) SAS
Features
Temperature / system monitoring
Fan monitoring
Fans that are no longer available, blocked or sticky fans are detected.
Fan control
The fans are regulated according to temperature. Maximum speed if the
housing cover has been opened.
Sensor monitoring
The removal of, or a fault in, a temperature sensor is detected. Should this
happen all fans monitored by this sensor run at maximum speed, to achieve the
greatest possible protection of the hardware.
Voltage monitoring
When voltage exceeds warning level high or falls below warning level low an
alert will be generated.
System Event Log (SEL)
All monitored events of the system board are recorded in the System Event Log.
They could be retrieved after a system reboot via ServerView.
D2630 (RX600 S3) SAS
17
Connectors and jumpers
Features
3.6
Connectors and jumpers
1 2
3
4
5
6
7
8
9
34 33
32
10
11
31 30
1
2
29
28
27
26
25
4
3
12
13
24
23 22 21 20
19 18 17 16 15
14
Figure 6: Schematic overview of the system board D2630
1 = J8C2 (jumper)
12 = Processor socket 4
13 = Processor socket 3
14 = SCSI connector channel A
2 = Memory board connector B
3 = Memory board connector A
4 = Battery
rd
15 = VRM 9.DO connector (for 3 LC-CPU)
16 = VRM 10.2 connector (CPU 4)
17 = VRM 10.2 connector (CPU 3)
18 = SCSI connector channel B
5 = SATA connector
6 = BMC connector
7 = Front panel connector
8 = PDB signal connector
9 = DC power connectors
10 = Processor socket 1
11 = Processor socket 2
19 = RAID DDR2 DIMM connector (RoMB)
20 = Memory board connector D
21 = Memory board connector C
22 = USB onboard connector
18
D2630 (RX600 S3) SAS
Features
Connectors and jumpers
23 = IPMI connector
29 = J4A4 (jumper)
30 = LAN 1 (top)
24 = GCM connector (not used)
25 = RAID Activation Key (RoMB)
26 = J4A1 (jumper)
31 = LAN 2 (bottom)
32 = Dual USB connector
33 = Serial connector (top)
34 = Video connector (bottom)
27 = J4A2 (jumper)
28 = J4A3 (jumper)
Settings with jumpers
The system board is supplied with all jumpers set on the following positions.
1
3
J4A1 = Password Clear
J4A2 = BIOS Write Protect
J4A3 = BIOS Recovery
J4A4 = NVRAM Clear
J8C2 = BMC Reset
Figure 7: Jumper default settings
J4A1 (26) - Password Clear
1-2 Password enabled
2-3 Password disabled/cleared
J4A2 (27) - BIOS Write Protect
1-2 BIOS unprotected
2-3 BIOS write protected
J4A3 (28) - BIOS Recovery
1-2 Normal boot
2-3 BIOS recovery
D2630 (RX600 S3) SAS
19
Connectors and jumpers
J4A4 (29) - NVRAM Clear
Features
1-2 NVRAM settings are not cleared
2-3 NVRAM settings cleared
J8C2 (1) - BMC Reset
1-2 BMC enabled
2-3 BMC disabled
3.6.1 External connectors
1
2
3
4
5
6
Figure 8: External connectors I/O shield
1 = Video connector
2 = Serial connector
3 = Dual USB connector
4 = LAN 1
5 = LAN 2
6 = GCM connector (not used)
LAN connectors
On this system board you will find one GbE Broadcom LAN controller 5704C.
This LAN controller supports the transfer rates of 10 Mbit/s, 100 Mbit/s and
1 Gbit/s. The LAN controller supports WOL function through Magic Packet™.
It is also possible to boot a device without its own boot hard disk via LAN. Here
Intel PXE is supported.
20
D2630 (RX600 S3) SAS
Features
RoMB
The LAN controller connectors are equipped with two LEDs (light emitting
diode) indicating the transfer rate and the activity.
1
2
Figure 9: LAN connectors
1
LAN link/activity
green
on
off
LAN connection
no LAN connection
flashing LAN transfer
2
LAN transfer rate
off
transfer rate 10 Mbit/s (or
no connection)
green
on
on
transfer rate 100 Mbit/s
transfer rate 1000 Mbit/s
orange
3.7
RoMB
The onboard Intel® IOP333 I/O processor becomes a RAID5 (RAID 0, 1, 5, 10,
50 ) controller by using a RAID activation key and a cache module. The following
figure shows the installed components.
1
2
Figure 10: RoMB; 1=RAID activation key, 2=cache module
D2630 (RX600 S3) SAS
21
Replacing the RAID Controller
Features
3.8
Replacing the RAID Controller
The MegaRAID™ SAS 8408E RAID controller is part of your system board
D2630. It offers the following features:
●
●
●
●
●
●
●
Eight internal SAS/SATA ports - Two x4 SFF 8484 connectors
3 Gb/s throughput per port
RAID Levels 0, 1, 5, 10, and 50
RAID 6 and 60 ready1
Greater than 2 TB array support
Intel®IOP333 I/O Processor
PCI Express 1.0a compliant
2.5 Gb/s and x8 interface
●
●
●
●
●
256MB DDRII 400 MHz SDRAM
Optional intelligent transportable battery backed DIMM module
Advanced data integrity and recovery
Enhanced error handling and reporting
FlexRAID®:
–
–
Online Capacity Expansion (OCE)
Online RAID Level Migration (RLM)
●
●
Comprehensive management and configuration utilities
Full SAS expander support (32 disk support)
This section describes what you have to do, when the RAID controller is
defective and has to be replaced.
Please take a few minutes to read this installation guide before you install a new
controller.
1
available in a subsequent release
22
D2630 (RX600 S3) SAS
Features
Replacing the RAID Controller
V
Caution!
Back up your data before you change your system configuration, to
ensure no loss of data.
Perform the following steps to install the new RAID™ SAS controller:
Step 1
Step 2
Unpack the controller
Unpack the new controller in a static-free environment. Remove
it from the antistatic bag and inspect it for damage.
If the controller appears to be damaged, contact FSC support
service.
Prepare the Computer
Turn off the computer and unplug the power cord(s) from the
back of the power supply. Remove the cover from the chassis.
V
Caution!
Make sure the computer is disconnected from the power
and from any networks before removing the controller.
Step 3
Review the Jumpers and Connectors
The following figure shows the location of the jumpers and
connectors on the RAID SAS controller. The jumpers are set at
the factory and you usually do not need to change them.
J1
J15
J3
J4
J5
J6 J7
J9
J10
U11
J11
J12 J18
U13
table 2 describes the jumpers and connectors on the controller.
D2630 (RX600 S3) SAS
23
Replacing the RAID Controller
Features
Jum- Type
pers
Description
J1
Universal Asynchronous
Receiver/Transmitter
(UART) debugging
3-pin connector
Reserved for internal use
J3
J4
GND connector
Reserved for internal use
x4 SAS ports 4 - 7
SFF 8484 x4 connector for connection to
physical drives and expanders.
J5
J6
I 2C connector
3-pin connector
Used for enclosure management.
Reserved for internal use
Onboard BIOS Enable
2-pin connector
the optional BIOS function is enabled or
disabled in software depending on the
status of this jumper.
No jumper: BIOS is enabled (default)
Jumper: BIOS is disabled
J7
Firmware Initialization
Mode Select
2-pin connector
If the firmware flashed onto the board is
corrupted, you need to mount jumper J7
(this holds the CPU core in reset), so you
can flash the firmware. Remove the
jumper after you flash the new firmware.
No jumper: this is the setting during
normal operation (Mode 3). This is the
default.
Jumper: this holds the CPU core in reset
(Mode 0).
Note: the card does not function as a
RAID controller if this jumper is
mounted.
J8
GND connector
Reserved for internal use
Table 2: Jumpers and Connectors
24
D2630 (RX600 S3) SAS
Features
Replacing the RAID Controller
Jum- Type
pers
Description
J9
I 2C connector
3-pin connector
Used for enclosure management.
Reserved for internal use
J10
Write Pending Indication
LED
2-pin connector
Connector for enclosure LED.
When lit, it indicates the onboard cache
contains data and a write from the cache
to the hard drives is pending. Optional.
J11
x4 SAS ports 0 - 3
SFF 8484 x4 connector for connection to
physical drives and expanders.
J12
J13
J14
J15
GND connector
GND connector
GND connector
I 2C connector
Reserved for internal use
Reserved for internal use
Reserved for internal use
4-pin connector
Used for enclosure management.
Reserved for internal use
J18
SMBUS header for
3-pin header
enclosure management
Used for enclosure management.
Reserved for internal use
Table 2: Jumpers and Connectors
Step 4
Remove the RAID SAS controller from the Mainboard
Remove the PCI card hold down latches that fix the RAID SAS
controller to the computer chassis.
Remove the RAID SAS controller from the PCI Express slot on
the motherboard (see your mainboard guide for information
about the PCI Express slot).
D2630 (RX600 S3) SAS
25
Replacing the RAID Controller
Features
Pull
here
Pull
here
Step 5
Installing the new RAID SAS controller
Press
here
Press
here
Insert the MegaRAID SAS controller in PCI Express slot #4 on
the motherboard, as shown in the figure above. Press down
gently but firmly to ensure the card is properly seated in the slot.
Secure the controller to the computer chassis with the PCI card
hold down latches (see your mainboard guide for information
about the PCI Express slot).
26
D2630 (RX600 S3) SAS
Features
Replacing the RAID Controller
Step 6
Power-Up the Computer
Replace the computer cover and reconnect the power cord(s).
Turn on the computer. Ensure that the SAS and/or SATA II
devices are powered up before or at the same time as the host
computer. If the host computer is powered up before the SAS or
SATA II devices, the devices might not be recognized.
During boot, a MegaRAID BIOS message similar to the
following displays:
LSI MEGARAID BIOS VERSION xxxx [date] Copyright(c)
2005, LSI Logic Corporation HA-1 (Bus x Dev y)
MegaRAID SAS 8408E PCI-Express RAID Controller
Standard FW xxxx DRAM=xxx MB(SDRAM)
Step 7
Step 8
Run the WebBIOS Configuration Utility
Run the WebBIOS Configuration Utility to configure the physical
arrays and logical drives. When the message Press
<Ctrl><H> for WebBIOSdisplays on the screen, press
CTRL+H immediately to run the utility.
Install the Operating System Driver
The SAS 8408E can operate under various operating systems.
To operate under these operating systems, you must install
software drivers.
The ServerSupport CD includes drivers for the supported
operating systems, along with documentation. You can view the
supported operating systems and download the latest drivers
for RAID adapters on the web site at:
D2630 (RX600 S3) SAS
27
4
Replacing the lithium battery
In order to save the system information permanently, a lithium battery is
installed to provide the CMOS-memory with a current. When the charge is too
low or the battery is empty, a corresponding error message is provided. The
lithium battery must then be replaced.
V
The lithium battery must be replaced with an identical battery or a battery
type recommended by the manufacturer (CR2032).
Do not throw lithium batteries into the trashcan. It must be disposed of in
accordance with local regulations concerning special waste.
Make sure that you insert the battery the right way round. The plus pole
must be on the top!
4
2
1
3
Figure 11: Replacing the lithium battery (holder is similar)
Ê
Ê
Remove the memory board in connector A (for description see the Operating
Manual of your server, chapter "Hot-plug Components").
Press the locking spring into direction of of the arrow (1), so that the lithium
battery jumps out of its socket.
Ê
Ê
Ê
Remove the battery (2).
Insert a new lithium battery of the same type into the socket (3) and (4).
Reinstall the memory board in connector A.
D2630 (RX600 S3) SAS
29
Abbreviations
The technical terms and abbreviations given below represent only a selection of
the full list of common technical terms and abbreviations.
Not all technical terms and abbreviations listed here are valid for the described
system board.
AC
Alternating Current
ACPI
Advanced Configuration and Power management Interface
ANSI
American National Standards Institute
ASR&R
Automatic Server Recovery and Restart
ATA
Advanced Technology Attachment
BBU
Battery Backup Unit
BIOS
Basic Input Output System
BMC
Baseboard Management Controller
CMOS
Complementary Metal Oxide Semiconductor
COM
COMmunication port
CPU
Central Processing Unit
D2630 (RX600 S3) SAS
31
Abbreviations
DDR
Double Data Rate
DIMM
DIP
Dual In-line Memory Module
Dual In-line Package
DMI
Desktop Management Interface
Dynamic Random Access Memory
Error Correction Code
DRAM
ECC
EEPROM
Electrical Erasable Programmable Read Only Memory
EFI
Extensible Firmware Interface
EGB
EMI
Elektrostatisch gefährdete Bauteile
Electromagnetic interference
EMRL
EMV
Embedded RAID Logic
Elektromagnetische Verträglichkeit (electromagnetic compatibility)
EPROM
Erasable Programmable Read Only Memory
ESD
ElectroStatic Discharge
32
D2630 (RX600 S3) SAS
Abbreviations
EVRD
HPC
FPC
FRU
FSB
ICE
Enterprise VRD
Hotplug Controller
Front Panel Controller
Field Replaceable Unit
Front Side Bus
In Circuit Emulation
IDE
Integrated (intelligent) Drive Electronics
International Electrotechnical Commission
Integrated Mirroring Enhanced
Intelligent Organisation Of PCI
Intelligent Platform Management Bus
Intelligent Platform Management Interface
International Organisation for Standardisation
Local Area Network
IEC
IME
IOOP
IPMB
IPMI
ISO
LAN
D2630 (RX600 S3) SAS
33
Abbreviations
LED
Light Emitting Diode
MPS
NMI
Multi Processor Specification
Non Maskable Interrupt
OEM
OHCI
OS
Original Equipment Manufacturer
Open Host Controller Interface
Operating System
PCI
Peripheral Components Interconnect
Prefailure Detection and Analyzing
Programmed Input Output
Power Distribution Board
PDA
PIO
PDB
PLD
PS(U)
PWM
PXE
Programmable Logic Device
Power Supply (Unit)
Pulse Wide Modulation
Preboot eXecution Environment
34
D2630 (RX600 S3) SAS
Abbreviations
RAID
Redundant Array of Inexpensive Disks
RoHS
Restriction of the Use of Certain Hazardous Substances (Waste from
Electric and Electronic Equipment, EU Directive)
RoMB
RSB
RAID on Motherboard
Remote Service Board
ReSeT
RST
RTC
Real Time Clock
SCSI
SATA
SDDC
Small Computer Systems Interface
Serial Advanced Technology Attachment
Single Device Data Correction
SDRAM
Synchronous Dynamic Random Access Memory
SEL
System Event Log
SHDG
SMB
SMM
Server Hardware Design Guide
System Management Bus
Server Management Mode
D2630 (RX600 S3) SAS
35
Abbreviations
SMP
Symmetrical Multi Processing
UHCI
USB
VGA
VRD
VRM
WEEE
WfM
WOL
Unified Host Controller Interface
Universal Serial Bus
Video Graphics Adapter
Voltage Regulator Down
Voltage Regulator Module
Waste from Electric and Electronic Equipment (EU Directive)
Wired for Management
Wake up On LAN
36
D2630 (RX600 S3) SAS
Fujitsu Siemens Computers GmbH
User Documentation
33094 Paderborn
Comments
Suggestions
Corrections
Germany
Fax: (++49) 700 / 372 00001
e-mail: [email protected]
Submitted by
Comments on System Board D2630
for RX600 S3 SAS
D2630 (RX600 S3) SAS
|