Fujitsu Computer Monitor P19 3 User Manual

English  
Monitor  
Operating Manual  
SCENICVIEW B17-3/B19-3/P19-3  
This manual was produced by  
Xerox Global Services  
Published by  
Fujitsu Siemens Computers GmbH  
Order No.: A26361-K1143-Z120-1-7619  
Edition 3  
AG 08/07  
SCENICVIEW  
B17-3/B19-3/P19-3  
LCD monitor  
Operating Manual  
august 2007 edition  
VESA, DDC and DPMS are registered trademarks of Video Electronics Standards  
Association.  
Copyright © Fujitsu Siemens Computers GmbH 2007  
All rights, including rights of translation, reproduction by printing, copying or similar methods,  
in part or in whole, are reserved.  
Offenders will be liable for damages.  
All rights, including rights created by patent grant or registration of a utility model or design,  
are reserved.  
Delivery subject to availability. Right of technical modification reserved.  
No liability for content and printing error.  
Contents  
Adjusting height, rake and rotation............................................................................................. 14  
Adjusting portrait format ............................................................................................................. 15  
Switching the monitor on and off (B17-3 / B19-3)....................................................................... 15  
Switching the monitor on and off (P19-3)................................................................................... 16  
Notes on power management .................................................................................................... 17  
Changing the monitor settings.................................................................................................... 18  
Notes on ergonomic colour adjustment.............................................................................................. 23  
Troubleshooting.................................................................................................................................. 24  
Notes regarding the DIN EN ISO 13406-2 standard .......................................................................... 26  
Technical data .................................................................................................................................... 27  
VESA-DDC-compatible VGA interface....................................................................................... 28  
Preset operating modes ............................................................................................................. 28  
Pin assignment D-SUB............................................................................................................... 29  
Monitor port DVI-D...................................................................................................................... 29  
A26361-K1143-Z120-1-7619, edition 3  
Contents  
A26361-K1143-Z120-1-7619, edition 3  
Introduction  
Your new LCD (Liquid Crystal Display) monitor SCENICVIEW B17-3/B19-3/P19-3 offers numerous  
features and functions, for example:  
TFT display (Thin Film Transistor; active matrix)  
minimal space requirements thanks to slim casing  
optimum ergonomic characteristics (totally distortion-free, excellent picture definition and colour  
purity right into the corners)  
high degree of brightness and good contrast  
high resolution (1280 x 1024)  
presentation of up to 16.7 million colours (in conjunction with an appropriate graphics card)  
automatic scanning of horizontal frequencies from 30 to 82 kHz and refresh rates (vertical  
frequencies) from 56 to 76 Hz (absolutely flicker-free)  
digital screen controller with microprocessor for storing 26 different display modes  
freely adjustable colour alignment for matching the screen colours to the colours of various  
input and output devices  
convenient operation via integrated OSD (On-Screen-display) menu  
VESA-DDC compatibility  
VESA-FPMPMI compatibility (Flat Panel Monitor Physical Mounting Interface) – Mounting  
device for swivel arm and wall bracket  
plug&play capability  
power management for reducing power consumption when the computer is not in use  
compliance with the recommendations in accordance with TCO’03  
The monitor fulfils all GS (“Geprüfte Sicherheit”, Certified Security) requirements.  
This operating manual contains important information you require to start up and run your LCD  
monitor.  
A graphics card (screen controller) with VGA interface or a digital graphics card with DVI interface is  
required to control the SCENICVIEW B17-3/B19-3/P19-3 LCD monitor. The monitor processes the  
data supplied to it by the screen controller. The screen controller or the associated driver software is  
responsible for setting the modes (resolution and refresh rate).  
When putting the monitor into operation for the first time, the screen display should be optimally  
adapted to the screen controller used and adjusted in accordance with your needs (see the  
"Changing the monitor settings" section in the "Operation of the monitor" chapter).  
Target group  
You don't need to be an "expert" to perform the operations described here. However, please observe  
the safety information given in the operating instructions of the computer and in this manual.  
In the event of any problems occurring, please contact your sales outlet or our help desk.  
Additional information  
Details of how you set the resolution and refresh rate are provided in the documentation on your  
screen controller/the associated driver software.  
For ergonomic reasons we recommend a screen resolution of 1280 x 1024 pixels for the monitors  
SCENICVIEW B17-3, B19-3 and P19-3.  
Because of the technology used (active matrix) an LCD monitor provides a totally flicker-free picture  
even with a refresh rate of 60 Hz.  
A26361-K1143-Z120-1-7619, edition 3  
1
 
SCENICVIEW B17-3/B19-3/P19-3  
Notational conventions  
The meanings of the symbols and fonts used in this manual are as follows:  
Pay particular attention to text marked with this symbol. Failure to observe this warning  
endangers your life, destroys the device, or may lead to loss of data.  
!
Supplementary information, remarks, and tips follow this symbol.  
i
Text which follows this symbol describes activities that must be performed in the order shown.  
"Quotation marks" indicate names of chapters or terms.  
This font indicates filenames and menu items.  
This fontindicates screen outputs.  
Important notes  
In this chapter you will find information regarding safety which is essential to take note of  
with your monitor.  
!
Safety notes  
This device complies with the relevant safety regulations for data processing equipment, including  
electronic office machines for use in an office environment. If you have any questions, contact your  
sales outlet or our help desk.  
The display surface of the LCD monitor is sensitive to pressure and scratches. You should  
therefore be careful with the display surface so as to avoid lasting damage (scratches).  
If the device is brought into the installation site from a cold environment, condensation can  
form. Before operating the device, wait until it is absolutely dry and has reached approximately  
the same temperature as the installation site.  
During installing and operating the device, please observe the instructions on environmental  
conditions in the "Technical data" chapter as well as the instructions in the "Installing an  
ergonomic video workstation" chapter.  
2
A26361-K1143-Z120-1-7619, edition 3  
   
SCENICVIEW B17-3/B19-3/P19-3  
To ensure sufficient ventilation, the intake and exhaust air openings of the monitor must never  
be blocked.  
The monitor automatically sets itself to a mains voltage in the range of 100 V to 240 V. Ensure  
that the local mains voltage lies within these limits.  
Ensure that the power socket on the device or the grounded mains outlet is freely accessible.  
The ON/OFF switch does not disconnect the device from the mains voltage. To completely  
disconnect the mains voltage, remove the power plug from the socket.  
The monitor is equipped with a power cable that complies with safety standards.  
Lay all cables so that nobody can stand on them or trip over them. When attaching the device,  
observe the relevant notes in the "Connecting the monitor" chapter.  
No data transfer cables should be connected or disconnected during a thunderstorm.  
Make sure that no objects (e.g. jewellery chains, paper clips, etc.) or liquids get inside the  
device (danger of electric shock, short circuit).  
The device is not waterproof! Never immerse the device in water and protect it from spray  
water (rain, sea water).  
In emergencies (e.g. damaged casing, elements or cables, penetration of liquids or foreign  
matter), switch off the unit, disconnect the power plug and contact your sales outlet or our help  
desk.  
The monitor must be disposed of in accordance with the local regulations for disposal of  
special waste. The screen background lighting contains mercury. You must observe the  
applicable handling and disposal safety regulations for fluorescent tubes.  
Only qualified technicians should repair the device. Unauthorised opening and incorrect repair  
may greatly endanger the user (electric shock, fire risk).  
You may set only those resolutions and refresh rates specified in the "Technical data" chapter.  
Otherwise you may damage your monitor. If you are in any doubt, contact your sales outlet or  
our help desk.  
Use a screen saver with moving images and activate the power management for your monitor  
to prevent still images from "burning in".  
If you operate the monitor with the swivel arm or wall bracket, it may not be turned by 180°.  
The SCENICVIEW B17-3/B19-3/P19-3 monitor may only be operated in landscape mode (0°)  
and portrait mode (90°). The control buttons are located at the bottom of the monitor in  
landscape mode (0°) and at the left-hand side of the monitor in portrait mode (90°).  
Store this manual close to the device. If you pass the device on to third parties, you should  
pass this manual on with it.  
A26361-K1143-Z120-1-7619, edition 3  
3
SCENICVIEW B17-3/B19-3/P19-3  
Power cable  
To guarantee safe operation, use the cable supplied. Use the following guidelines if it is necessary to  
replace the original cable set.  
The female/male receptacles of the cord set must meet IEC60320/CEE-22 requirements.  
The cable has to be HAR-certified or VDE-certified. The mark HAR or VDE will appear on the  
outer sheath.  
For devices which are mounted on a desk or table, type SVT or SJT cable sets may be used.  
For devices which sit on the floor, only SJT type cable sets may be used.  
The cable set must be selected according to the rated current for your device.  
If necessary, replace the original power cable with a regular grounded 3-core mains lead.  
Transport  
Transport the monitor with care and only in its original packaging or another corresponding  
packaging fit to protect it against knocks and jolts.  
Never drop the LCD monitor (danger of glass breakage).  
Cleaning  
Always pull out the power plug before you clean the monitor.  
Do not clean any interior parts yourself, leave this job to a service technician.  
Do not use any cleaning agents that contain abrasives or may corrode plastic.  
Ensure that no liquid will run into the system.  
Ensure that the ventilation areas of the monitor are free.  
The display surface of the LCD monitor is sensitive to pressure and scratches. Clean it only  
using a soft, slightly moistened cloth.  
Wipe the monitor casing with a dry cloth. If the monitor is particularly dirty, use a cloth which has  
been moistened in mild domestic detergent and then carefully wrung out.  
CE marking  
The shipped version of this device complies with the requirements of the following EC  
Directives: 2004/108/EC "Electromagnetic Compatibility" and 2006/95/EC "Low Voltage  
Directive".  
4
A26361-K1143-Z120-1-7619, edition 3  
 
SCENICVIEW B17-3/B19-3/P19-3  
FCC Class B Compliance Statement  
The following statement applies to the products covered in this manual, unless otherwise specified  
herein. The statement for other products will appear in the accompanying documentation.  
NOTE:  
This equipment has been tested and found to comply with the limits for a "Class B" digital device,  
pursuant to Part 15 of the FCC rules and meets all requirements of the Canadian Interference-  
Causing Equipment Standard ICES-003 for digital apparatus. These limits are designed to provide  
reasonable protection against harmful interference in a residential installation. This equipment  
generates, uses and can radiate radio frequency energy and, if not installed and used in strict  
accordance with the instructions, may cause harmful interference to radio communications. However,  
there is no guarantee that interference will not occur in a particular installation. If this equipment does  
cause harmful interference to radio or television reception, which can be determined by turning the  
equipment off and on, the user is encouraged to try to correct the interference by one or more of the  
following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between equipment and the receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is  
connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Fujitsu Siemens Computers GmbH is not responsible for any radio or television interference caused  
by unauthorised modifications of this equipment or the substitution or attachment of connecting  
cables and equipment other than those specified by Fujitsu Siemens Computers GmbH. The  
correction of interferences caused by such unauthorised modification, substitution or attachment will  
be the responsibility of the user.  
The use of shielded I/O cables is required when connecting this equipment to any and all optional  
peripheral or host devices. Failure to do so may violate FCC and ICES rules.  
Declaration of Conformity  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two  
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any  
interference received, including interference that may cause undesired operation.  
Product name:  
Colour LCD Monitor  
Trade name:  
Fujitsu Siemens Computers Inc.  
SCENICVIEW B17-3/B19-3/P19-3  
Model number(s):  
Name of responsible party:  
Fujitsu Siemens Computers Inc.  
1250E. Arques Avenue  
Sunnyvale, CA 94085  
U.S.A.  
Contact person:  
Phone No.:  
Fax No.:  
Schroettle-Henning, Bernd  
(408) 834-0306  
(408) 746-8299  
We, Fujitsu Siemens Computers Inc., hereby declare that the equipment bearing the trade name and  
model number specified above was tested confirming to the applicable FCC Rules under the most  
accurate measurement standards possible, and that all the necessary steps have been taken and  
are in force to assure that production units of the same equipment will continue to comply with the  
Commissions requirements.  
A26361-K1143-Z120-1-7619, edition 3  
5
 
SCENICVIEW B17-3/B19-3/P19-3  
Energy Star Guidelines  
The Fujitsu Siemens LCD monitor SCENICVIEW B17-3/B19-3/P19-3 is  
designed to conserve electricity by dropping to less than 1 W when it goes  
into standby, suspend and OFF mode. With this new power management  
the LCD monitor SCENICVIEW B17-3/B19-3/P19-3 qualifies for the U.S.  
Environmental Protection Agency's (EPA) Energy Star Computers award.  
The EPA estimates that computer equipment uses 5 % percent of all business electricity and that  
this is growing rapidly. If all desktop computers and peripherals enter a low-power mode when not in  
use, the overall savings in electricity could amount to $ 2 thousand million annually. These savings  
could also prevent the emission of 20 million tons of carbon dioxide into the atmosphere - the  
equivalent of 5 million automobiles.  
As an Energy Star Partner, Fujitsu Siemens Computers GmbH has determined that this product  
meets the Energy Star guidelines for energy efficiency.  
Disposal and recycling  
This device has been manufactured to the highest possible degree from materials which can be  
recycled or disposed of in a manner that is not environmentally damaging. The device may be taken  
back after use to be recycled, provided that it is returned in a condition that is the result of normal  
use. Any components not reclaimed will be disposed of in an environmentally acceptable manner.  
If you have any questions on disposal, please contact your local office, our help desk, or:  
Germany  
Belgium  
Switzerland  
Fujitsu Siemens Computers  
GmbH  
Remarketing und Recycling  
D-33106 Paderborn  
Tel.: +49 5251 / 81 80 10  
Fax: +49 5251 / 81 80 15  
RECUPEL  
Boulevard Reyers, 80  
B-1030 Brussels  
Tel.: +32 2 / 706 86 16  
Fax: +32 2 / 706 86 13  
SWICO  
Schweizerischer  
Wirtschaftsverband der  
Informations-,  
Kommunikations- und  
Organisationstechnik  
A list of the SWICO  
Acceptance places can be  
found at:  
Asia  
USA  
Taiwan: Environmental  
Protection Administration  
Executive Yuan R.O.C.  
Fujitsu Siemens  
Computers Inc.  
1250E. Arques Avenue  
Sunnyvale, CA 94085 U.S.A.  
Contact: Schroettle-Henning,  
Bernd  
Phone No.: (408) 834-0306  
Fax No.: (408) 746-8299  
You can find more information on the Internet at www.fujitsu-siemens.com/recycling.  
6
A26361-K1143-Z120-1-7619, edition 3  
 
SCENICVIEW B17-3/B19-3/P19-3  
Checking the contents of the consignment  
The display surface of the LCD monitor is sensitive to pressure and scratches. Always  
hold the device by the casing!  
!
Unpack all the individual parts.  
Check the delivery for damage incurred during transportation.  
Check whether the delivery agrees with the details in the delivery note.  
The complete LCD monitor package includes:  
one monitor  
one data cable (D-SUB)  
one data cable (DVI-D)  
one audio cable  
one power cable  
one CD with software and documentation  
one Warranty Booklet  
one "Getting Started" manual  
Should you discover that the delivery does not correspond to the delivery note, notify your local sales  
outlet immediately.  
We recommend that you keep the original packaging material. Keep it for future  
transportation.  
i
A26361-K1143-Z120-1-7619, edition 3  
7
 
SCENICVIEW B17-3/B19-3/P19-3  
Installing an ergonomic video workstation  
2
1
1
Avoid glare from electric  
lighting.  
1 = Windows  
1 = Edge of desk  
2 = Permissible reaching  
sector  
Avoid direct and reflected glare.  
Position the keyboard where it  
is easiest to reach.  
1
0°  
65°  
30°  
30°  
60°  
65°  
2
2
Example layout of monitor,  
keyboard and copy-holder  
1 = Bearing surface for palms  
of hands  
2 = Reaching area for  
frequently used equipment  
1 = Preferred viewing distance  
2 = Permissible viewing  
distance  
Position the monitor for  
distance to the monitor should  
be approximately 50 cm.  
Position the monitor for  
optimum viewing. The viewing  
distance to the monitor should  
be approximately 50 cm.  
Keep ventilated areas clear.  
i
Depending on the situation, the use of a swivel arm or wall bracket (VESA FPMPMI), are available  
from specialised dealers, may be advisable. For this purpose the monitor base must be removed  
beforehand as described in the "Mounting and removing the monitor base" chapter.  
8
A26361-K1143-Z120-1-7619, edition 3  
   
SCENICVIEW B17-3/B19-3/P19-3  
Mounting and removing the monitor base  
The display surface is susceptible to scratching! Therefore, lay the monitor on a soft  
surface when mounting or removing the monitor base.  
!
Folding out monitor base  
When delivered the lower part of the monitor base is folded up and secured to the monitor by a  
collar.  
The monitor base springs up about 5 cm when the collar is released.  
!
Lay the monitor on its face on a soft surface (A).  
First release one of the collar fasteners (1).  
Release carefully the second collar fastener (2).  
The monitor base can now be folded out.  
A26361-K1143-Z120-1-7619, edition 3  
9
   
SCENICVIEW B17-3/B19-3/P19-3  
Proceed according to the four steps in the illustrations to fold out the monitor base.  
10  
A26361-K1143-Z120-1-7619, edition 3  
SCENICVIEW B17-3/B19-3/P19-3  
Removing monitor base  
Before you can use a swivel arm or a wall bracket, you must remove the monitor base:  
The display surface is susceptible to scratching!  
!
Switch off the monitor and pull the power plug out of the power socket.  
Lay the monitor on its face on a soft surface.  
Remove the cover and disconnect all cables.  
Remove the four screws on the rear of the  
monitor.  
You can now mount a swivel arm or a wall  
bracket as per VESA FPMPMI with 100 mm hole  
spacing.  
For instructions on how to mount the swivel arm  
or wall bracket, please see the documentation for  
the swivel arm or wall bracket.  
If you operate the monitor with the swivel arm or wall bracket, it may not be turned by 180°.  
!
A26361-K1143-Z120-1-7619, edition 3  
11  
 
SCENICVIEW B17-3/B19-3/P19-3  
Connecting the monitor  
Please take note of the safety information in the "Important notes" chapter.  
!
CE conformance and optimum picture quality are guaranteed only if you use the data  
cables supplied.  
Do not cover the ventilation openings of the monitor.  
The computer power plug must be pulled out!  
Be sure that the monitor and the computer are switched off.  
12  
A26361-K1143-Z120-1-7619, edition 3  
   
SCENICVIEW B17-3/B19-3/P19-3  
Connecting cables to the monitor  
The monitor ports are protected by a cover.  
Remove the cover.  
1
2
3 5  
7
7
1 = Power connector  
2 = DVI-D connection socket (DIGITAL)  
3 = D-SUB connection socket (ANALOG)  
4 = Security slot for "Kensington Lock"  
5 = AUDIO-IN connector  
6 = Cover position  
7 = Holes for fixing swivel arm or wall bracket  
4
6
The data cables supplied have two 15-pin D-SUB connectors / two 24-pin DVI connectors for  
connection to the monitor and to the computer.  
Select the suitable data cable for your computer.  
Digital graphics card with DVI interface:  
Graphics card with VGA interface:  
DVI connector  
D-SUB connector  
Information on the computer connections and interfaces is contained in the operating manual  
for your computer.  
Connect one of the connectors of the data cable to the D-SUB connector (3) or the DVI-D  
connector (2) on the monitor and secure the plug-in connection by tightening the safety screws.  
The monitor automatically detects the input when only one signal source is connected.  
i
i
Insert one plug of the audio line in the AUDIO IN (5) socket on the monitor and make sure it is  
properly engaged.  
Plug the power cable supplied into the power connector (1) of the monitor.  
Mount the cover over the connections.  
A lock (Kensington Lock) can be mounted in the security slot (4) to protect the monitor  
from theft. A Kensington Lock is not included in the consignment of the monitor.  
A26361-K1143-Z120-1-7619, edition 3  
13  
 
SCENICVIEW B17-3/B19-3/P19-3  
Connecting cables to the computer  
Information on the computer connections and interfaces is contained in the operating manual for your  
computer.  
If your computer has two monitor ports ("onboard" screen controller and separate  
graphics card), the monitor port for the separate graphics card is usually active.  
i
Connect the data cable to the (active) monitor port on the computer and secure the plug-in  
connection by tightening the safety screws.  
Insert the other plug of the audio line in the audio output of the computer.  
Plug the connector of the mains cable provided into the monitor outlet of the computer or into a  
properly earthed outlet and ensure a safe connection.  
Plug the power connector of the computer into a properly grounded mains outlet.  
When you start working with your monitor for the first time you should install the  
appropriate graphics drivers for your application software. Details of how to do this are  
provided in the documentation on your screen controller/the associated driver software.  
i
Operation of the monitor  
The monitor offers the following possibilities that enable it to be optimally adjusted for the respective  
user and the respective situation.  
Adjusting height, rake and rotation  
The height of the monitor can be adjusted by approximately 120 mm.  
Grasp the monitor with both hands on the right and left edge of the casing and move it up or  
down.  
The rake of the monitor can be adjusted by -2° (forward) and +35° (back) from its vertical position.  
Grasp the monitor with both hands on the right and left edge of the casing and adjust it to the  
desired rake.  
The monitor can be turned horizontally by approximately 90° from its central position.  
Grasp the monitor with both hands on the right and left edge of the casing and turn it to the  
desired position.  
14  
A26361-K1143-Z120-1-7619, edition 3  
   
SCENICVIEW B17-3/B19-3/P19-3  
Adjusting portrait format  
The monitor can be turned from the "wide format" (landscape mode) into the "high format" position  
(portrait mode).  
Grasp the monitor with both hands on the right and left edge of the casing, move it into the  
highest position and turn it clockwise until it is in the portrait position.  
You must use corresponding software (pivot software) so that the screen display is also  
shown in the portrait mode. This software is included in the delivery (CD-ROM) and must  
be installed on your computer.  
i
In the OSD menu you have the option of switching the OSD manually from landscape mode  
into portrait mode (see section "Monitor settings using the OSD menu").  
To reset the monitor to the landscape mode, the monitor must be turned counter-clockwise. The  
OSD display can be reset again in the OSD menu.  
Switching the monitor on and off (B17-3 / B19-3)  
The ON/OFF switch at the front is used for switching the monitor on and off.  
3 2  
1
1 = Buttons for the OSD menu  
(On-Screen-display)  
2 = ON/OFF switch  
3 = Power indicator  
1
3
2
The buttons are to be pressed from the bottom upwards.  
i
A26361-K1143-Z120-1-7619, edition 3  
15  
 
SCENICVIEW B17-3/B19-3/P19-3  
Switching the monitor on and off (P19-3)  
The main switch on the underside and the On/Off switch on the front of the monitor are used to  
switch it on and off.  
Switch on the monitor via the main switch (4) on the underside.  
43 2  
1
1 = Buttons for the OSD menu  
(on-screen display)  
2 = On/Off switch  
3 = Mains power indicator  
4 = Main switch  
1
3
2
The mains power indicator (3) lights up blue when the monitor and the computer are switched on.  
The mains power indicator lights up orange when the monitor is not receiving a video signal or when  
it is in energy saving mode. The mains power indicator goes out when the monitor is switched off.  
When you switch the computer system on, you must proceed in the following order:  
First switch on the LCD monitor with the ON/OFF switch (2).  
Then switch on the computer.  
If your computer has a power management function (energy-saving mode), you should  
read the "Notes on power management" section in this chapter.  
i
16  
A26361-K1143-Z120-1-7619, edition 3  
 
SCENICVIEW B17-3/B19-3/P19-3  
Notes on power management  
If your computer is equipped with power management, the monitor can support this function fully.  
Here the monitor does not distinguish between the individual energy-saving modes of the computer  
(standby mode, suspend mode and OFF mode), as it is capable of immediately switching into the  
mode with the highest energy-saving effect.  
Stage  
Power indicator  
Function  
ON  
Power-Saving Mode  
lights up orange  
lights up blue  
the monitor is working  
normally  
the screen is dark  
Power consumption  
Normal  
reduced to < 1 W  
< 37 W typical  
If your computer detects inactivity (no input) it sends an appropriate signal to the monitor to reduce  
the power consumption (energy-saving mode). The power indicator of the monitor changes colour to  
indicate the status change.  
Once an input is made at the computer the screen contents are redrawn and full power is restored.  
For detailed information on how energy-saving mode operates refer to the operating manual or  
technical manual of the computer.  
When the monitor is switched to the energy-saving mode by the power management  
system a power consumption of up to 1 W is maintained to feed the circuit for redrawing  
the screen contents.  
i
In order to stop the monitor from using any power at all, switch it off at the main switch on  
the underside (P19-3).  
A26361-K1143-Z120-1-7619, edition 3  
17  
   
SCENICVIEW B17-3/B19-3/P19-3  
Changing the monitor settings  
When putting the monitor into operation for the first time, the screen display should be optimally  
adapted to the screen controller used and adjusted in accordance with your needs.  
Choosing basic monitor settings using the supplied software  
If one of the operating systems Windows 95/98, Windows NT, Windows Me, Windows 2000,  
Windows XP or OS/2 (with Windows emulation installed) is used, the basic monitor settings can be  
set with the CD supplied.  
Insert the supplied CD into the CD-ROM drive.  
Open the Readme file on the CD and follow the instructions in the file.  
Your monitor should now already be properly adjusted. If none of the above operating systems is  
used or minor corrections are to be made to the screen display, then change the monitor settings  
with the OSD menu.  
Changing the monitor settings with the buttons of the control panel  
1 = Buttons for the OSD menu  
(On-Screen-display)  
2 = ON/OFF switch  
3 = Power indicator  
Use the buttons of the control panel to make the following monitor settings directly while the OSD  
menu is switched off.  
Performing auto-adjustment of the monitor  
Press the AUTO button for approx. 1 second while the OSD menu is switched off.  
The Auto Processing message is displayed.  
Picture quality and position are set to optimum values for your system.  
Selecting input signal (D-SUB/DVI-D)  
Press the INPUT button for calling the Input select setting window.  
Press the or button to select the desired input (analogue D-SUB or digital DVI-D).  
6
5
This setting window can also be called, when the OSD menu is locked.  
Activating/deactivating muting  
Press the  
button to switch the sound off and on again.  
A message is displayed that the action has been performed.  
18  
A26361-K1143-Z120-1-7619, edition 3  
   
SCENICVIEW B17-3/B19-3/P19-3  
Locking the OSD menu  
The OSD menu can be locked to prevent accidental or unauthorised changes to the monitor settings.  
Press and hold the SELECT/MENU button for a few seconds while you switch on the monitor  
with the ON/OFF switch.  
A message is displayed that the action has been performed.  
Please proceed in the same manner to release the locked OSD menu again.  
Locking the ON/OFF button  
The ON/OFF switch can be locked to prevent accidental or unauthorised changes to the monitor  
settings.  
Press and hold both buttons  
and  
simultaneously for a few seconds.  
6
5
A message is displayed that the action has been performed.  
Please proceed in the same manner to release the locked ON/OFF switch again.  
Monitor settings using the OSD menu  
With the buttons on the control panel, call up and use the integrated OSD (On-Screen display) menu.  
The OSD menu is available in different languages. The English menu names are used in  
the following description (default setting). With the OSD function Language in the OSD Setup  
you can select another language.  
i
To set the OSD menu, perform the following steps:  
Press the SELECT/MENU button to activate the OSD menu.  
The main menu appears on the screen (on the left-hand side) with icons for the setting functions.  
The first symbol (Brightness/Contrast) is  
highlighted. In the right-hand part of the display  
the associated functions are shown.  
If necessary, press the  
or  
button to  
mark another icon (e.g.6Image5adjust).  
Press the SELECT/MENU button to select  
the highlighted icon.  
A26361-K1143-Z120-1-7619, edition 3  
19  
 
SCENICVIEW B17-3/B19-3/P19-3  
The corresponding setting window (here: Image Adjust) is displayed (on the right-hand side).  
The first function (H-Position) is highlighted.  
If necessary, press the  
mark another function.  
or  
button to  
6
5
Press the SELECT/MENU button to select  
the highlighted function.  
Press the  
value for the selected function.  
or  
button to adjust the  
6
5
Press the EXIT/AUTO button to exit the  
function.  
If necessary, press the button  
mark another function or press the  
or  
to  
6
5
EXIT/AUTO button to return to the main  
menu.  
All changes are stored automatically.  
If you want to change other settings, select the corresponding function from the OSD main menu. All  
possible adjustments of the main menu are described in the following.  
The OSD menu for analogue monitor operation is described in the following. During digital  
operation some functions are not available, as they are not required due to the digital  
transmission technology used.  
i
Adjusting the brightness and contrast  
Calling the Brightness / Contrast setting window  
Setting the brightness of the display  
Brightness  
Contrast  
With this function you change the brightness of the background lighting.  
Setting the contrast of the display  
With this function you modify the contrast of bright colour tones.  
Setting the brightness of the display  
Black Level  
Auto Level  
With this function you modify the contrast of dark colour tones.  
Setting the brightness of the display  
With this function you can automatically set the contrast.  
Press the SELECT/MENU button to activate the function.  
If the contrast is set too high, bright surfaces can no longer be distinguished from very  
bright surfaces. If the contrast is set too low, the maximum brightness will not be achieved.  
i
20  
A26361-K1143-Z120-1-7619, edition 3  
SCENICVIEW B17-3/B19-3/P19-3  
Adjusting size and position  
Calling the Image adjust setting window  
Adjusting the horizontal position  
H-Position  
V-Position  
Clock  
With this function you move the picture to the left or to the right.  
Adjusting the vertical position  
With this function you move the picture up or down.  
Setting synchronisation  
With this function you adjust the picture width to eliminate vertical picture  
disturbances.  
Eliminating picture interference  
Phase  
With this function you fine-tune your monitor to eliminate picture interference.  
Adjusting the volume  
Calling the Audio setting window  
Setting the volume for playback with the integrated loudspeakers  
Switching the loudspeakers off or on  
Volume  
Mute  
Setting colour temperature and colours  
Calling the Colour setting window  
Selecting the colour temperature  
The "warmth" of the screen colours is set using the colour temperature. The colour  
temperature is measured in K (= Kelvin). You can select from sRGB, 6500 K,  
9300 K, Native and Custom Colour.  
sRGB  
= setting colour display according to the sRGB standard  
= Original colour of the LCD display  
= User-defined colours  
Native  
Custom Colour  
In the user-defined setting you can change the colour ratios of the basic colours  
(red, green, blue) as required.  
A26361-K1143-Z120-1-7619, edition 3  
21  
SCENICVIEW B17-3/B19-3/P19-3  
Setting display of the OSD menu  
Calling the OSD Setup setting window  
Setting language for the OSD menu  
Language  
With this function you choose between English (default setting), French, German,  
Italian and Spanish as the language for the OSD menu.  
Setting the horizontal position of the OSD menu  
OSD  
H-Position  
With this function you move the OSD menu to the left or to the right.  
Setting the vertical position of the OSD menu  
OSD  
V-Position  
With this function you move the OSD menu up or down.  
Setting the display duration of the OSD menu  
OSD  
Timeout  
With this function you select a value from 10 to 120 seconds.  
If the set time expires without a setting being made, the OSD menu is automatically  
faded out.  
Setting the display format of the OSD menu  
OSD  
Rotation  
With this function you switch the OSD menu from portrait mode to landscape mode  
and vice versa.  
Off = The OSD menu is displayed in portrait mode.  
On = The OSD menu is displayed in landscape mode.  
Setting functions in the "Advanced" menu  
Calling the Advanced setting window  
Selecting input signal  
Input select  
DDC-CI  
With this function you switch the monitor from the analogue to the digital mode and  
vice versa, when two signal sources are connected.  
The condition is that the graphic card used supports this function.  
Activate/deactivate DDC-CI function  
On = the DDC-CI function is activated (default setting)  
Off = the DDC-CI function is deactivated  
Displaying monitor data  
Resolution  
Notifier  
The optimum resolution for this monitor is 1280 x 1024 pixels. With the function  
activated (On), a message appears on the screen after approx. 30 seconds if a  
different resolution is set.  
Change the resolution to 1280 x 1024 to achieve optimum picture quality.  
With the function deactivated (Off), no message appears.  
Activating the factory settings  
Factory Recall  
With this function all settings are reset to the factory settings without prompting for  
confirmation.  
Press the SELECT/MENU button to activate the function. The Auto Processing  
message is displayed.  
22  
A26361-K1143-Z120-1-7619, edition 3  
SCENICVIEW B17-3/B19-3/P19-3  
Displaying information  
Calling the Information setting window  
With this function the model designation, serial number, resolution, H/V frequency,  
input signal and polarity of the synchronisation signal are displayed.  
Notes on ergonomic colour adjustment  
If you select colours for the display in your application programmes, take note of the information  
below.  
The primary colours blue and red on a dark background do not produce the minimum required  
contrast of 3:1 and are therefore not suitable for continuous text and data entry.  
When using several colours for characters and background and giving the primary colours full  
modulation, you can obtain very suitable colour combinations (see the following table):  
Background  
Characters  
black  
white  
+
purple  
blue  
cyan  
green  
yellow  
red  
black  
white  
purple  
blue  
+
+
-
+
-
+
-
+
-
+
-
-
+
-
+
+
-
+
+
-
-
-
-
-
-
+
-
+
-
-
cyan  
green  
yellow  
red  
+
+
+
-
+
+
+
-
-
-
-
-
-
-
-
-
-
-
+
-
-
-
+
+
+
+
-
Colour combination very suitable  
Colour combination not suitable because colour locations are too close together, thin characters  
are not identifiable or rigorous focusing is demanded of the human eye.  
A26361-K1143-Z120-1-7619, edition 3  
23  
 
SCENICVIEW B17-3/B19-3/P19-3  
Troubleshooting  
Should an error occur, first check the following points. If the distortion is still not eliminated, the  
monitor should, if possible, be checked on another computer.  
If you are unable to solve the problem, please inform our help desk.  
Having this problem?  
Check the following points:  
No screen display  
(power indicator does not light)  
Check whether the main switch on the underside  
of the monitor is switched on (P19-3).  
Check whether the power cable on the monitor is  
connected correctly.  
Check whether the computer is switched on.  
Check whether the computer is switched on.  
No screen display  
(power indicator lights)  
Check whether the data cable for the monitor is  
correctly attached to the monitor port on the  
computer.  
Press any key on the computer keyboard - the  
computer may be in energy saving mode.  
Alter the brightness and/or contrast until you get a  
picture.  
Message:  
No Signal  
Check whether the data cable for the monitor is  
correctly attached to the monitor port on the  
computer.  
Check whether the computer is switched on.  
Message:  
Frequency out of range:  
## kHz / ## Hz  
The input signal (horizontal frequency and refresh rate)  
at the displayed input does not correspond to the  
technical monitor data.  
Please change the display mode to  
1280 x 1024 with 60 Hz  
Adjust the video frequency range using the  
computer software (see documentation for your  
computer or your graphics card).  
Adjust a different screen resolution using the  
computer software (see documentation for your  
computer or your screen controller).  
Picture position not correct  
Picture is shaking  
The monitor recognises an undefined mode (see the  
"Technical data" chapter).  
Press the EXIT/AUTO button to perform the auto-  
adjustment of the screen.  
Check whether the data cable for the monitor is  
correctly attached to the monitor port on the  
computer.  
Press the EXIT/AUTO button to perform the auto-  
adjustment of the screen.  
24  
A26361-K1143-Z120-1-7619, edition 3  
 
SCENICVIEW B17-3/B19-3/P19-3  
Having this problem?  
Check the following points:  
Picture is wrongly adjusted  
Press the SELECT/MENU button to activate the  
function Factory Recall. The Auto Processing  
message is displayed.  
Picture disturbances (vertical lines)  
Press the EXIT/AUTO button to perform the auto-  
adjustment of the screen.  
Picture disturbances (horizontal lines,  
picture noise)  
Press the EXIT/AUTO button to perform the auto-  
adjustment of the screen.  
The background lighting has a limited lifetime. If your  
monitor display should become too dark, the  
background lighting will have to be exchanged.  
The screen becomes darker  
Please contact our help desk.  
A26361-K1143-Z120-1-7619, edition 3  
25  
SCENICVIEW B17-3/B19-3/P19-3  
Notes regarding the DIN EN ISO 13406-2 standard  
Permanently unlit or lit pixels  
The standard of production techniques today cannot guarantee an absolutely fault-free screen  
display. A few isolated constant lit or unlit pixels (picture elements) may be present. The maximum  
permitted number of pixels faults is stipulated in the stringent international standard ISO 13406-2  
(Class II).  
Examples:  
A 17" or 19" flat-screen monitor with a resolution of 1280 x 1024 has 1280 x 1024 = 1310720 pixels.  
Each pixel consists of three subpixels (red, green and blue), so there are almost 4 million subpixels  
in total. In accordance with ISO 13406-2 (Class II), a maximum of 6 pixels and 7 subpixels may be  
faulty.  
Pixel  
A pixel consists of 3 subpixels, normally red, green and blue. A pixel  
is the smallest element that can be generated by complete  
functionality of the display.  
Subpixel  
Cluster  
A subpixel is a separately addressable internal structure within a pixel  
that enhances the pixel function.  
A cluster contains two or more defective pixels or subpixels in a 5 x 5  
pixel block.  
26  
A26361-K1143-Z120-1-7619, edition 3  
 
SCENICVIEW B17-3/B19-3/P19-3  
Technical data  
B17-3  
B19-3 / P19-3  
Dimensions and weight  
Visible diagonals:  
Dot pitch:  
43 cm  
48 cm  
0.264 mm  
0.294 mm  
Screen size:  
Width:  
Height:  
337.9 mm  
270.3 mm  
376.3 mm  
301 mm  
Maximal resolution:  
1280 x 1024  
1280 x 1024  
Dimensions incl.  
monitor base:  
Width:  
Height:  
Depth:  
375 mm  
469 mm  
249 mm  
412 mm  
497 mm  
249 mm  
Box dimensions:  
Width:  
Height:  
Depth:  
438 mm  
418 mm  
176 mm  
484 mm  
452 mm  
176 mm  
Weight (without packaging):  
approx. 6.8 kg  
approx. 7.5 kg  
Storable display modes:  
25  
25  
Pixel error classes according to  
ISO 13406-2:  
Class II  
Class II  
Accessories:  
Power cable (1.8 m)  
D-SUB data cable (1.8 m)  
DVI-D data cable (1.8 m)  
Audio cable (1.8 m)  
Electrical data  
Video:  
Analogue, positive, 0.7 Vpp, 75  
Digital: DVI-D  
Synchronisation:  
Horizontal frequency:  
Refresh rate:  
Separate Sync. TTL, positive or negative  
30 kHz .... 82 kHz (multi-scanning)  
56 Hz .... 76 Hz  
Maximum pixel rate:  
Power supply:  
135 MHz  
switches automatically  
100 V - 240 V, 50 Hz - 60 Hz  
Total power consumption:  
Sound output:  
< 37 W in normal mode  
< 1 W in energy-saving mode  
(standby mode, suspend mode and OFF mode)  
2.0 W left; 2.0 W right  
A26361-K1143-Z120-1-7619, edition 3  
27  
   
SCENICVIEW B17-3/B19-3/P19-3  
Environmental conditions  
Environment class 3K2, IEC 721  
Rated range of operation:  
Humidity:  
15 °C .... 35 °C  
20 % .... 85 %  
Limit range of operation:  
Humidity:  
5 °C .... 35 °C  
20 % .... 85 %  
Condensation must be avoided.  
VESA-DDC-compatible VGA interface  
Your monitor is equipped with a VESA-DDC-compatible VGA interface. VESA-DDC (Video  
Electronics Standard Association, Display Data Channel) is used as the communications interface  
between the monitor and the computer. If your computer is equipped with a VESA-DDC-compatible  
VGA interface, it can automatically read the data for ensuring optimum operation from your monitor  
and select the appropriate settings.  
If the monitor SCENICVIEW B17-3/B19-3/P19-3 is not yet displayed in the list of  
monitors, you can select the following monitor instead:  
i
Fujitsu Siemens P17-2, P19-2, B17-2, B19-2  
Preset operating modes  
The picture position and size have been set to optimum values at the factory for the  
operating modes listed above. Depending on the screen controller used, it may be  
necessary to adjust the display position and size. In this case, you can change and save  
the settings (see "Operation of the monitor").  
i
The following are the most frequently used of the preset operating modes:  
Horizontal frequency  
Refresh rate  
Screen resolution  
31.5 kHz  
31.5 kHz  
37.5 kHz  
37.9 kHz  
46.9 kHz  
48.4 kHz  
60.0 kHz  
64.0 kHz  
80.0 kHz  
70 Hz  
60 Hz  
75 Hz  
60 Hz  
75 Hz  
60 Hz  
75 Hz  
60 Hz  
75 Hz  
720 x 400  
640 x 480  
640 x 480  
800 x 600  
800 x 600  
1024 x 768  
1024 x 768  
1280 x 1024  
1280 x 1024  
For ergonomic reasons, a screen resolution of 1280 x 1024 pixels is recommended. Because of the  
technology used (active matrix) an LCD monitor provides a totally flicker-free picture even with a  
refresh rate of 60 Hz.  
28  
A26361-K1143-Z120-1-7619, edition 3  
 
SCENICVIEW B17-3/B19-3/P19-3  
Pin assignment D-SUB  
1
5
6
10  
11  
15  
Pin  
1
Meaning  
Video input red  
Video input green  
Video input blue  
Earth  
Pin  
Meaning  
+5 V (DDC)  
Sync. earth  
Earth  
9
2
10  
11  
12  
13  
14  
15  
3
4
DDC-Data  
H. sync  
5
Earth  
6
Red video earth  
Green video earth  
Blue video earth  
V. sync  
7
DDC Clock  
8
Monitor port DVI-D  
1
9
17  
Pin  
1
Meaning  
TMDS Data2-  
TMDS Data2+  
Pin  
Meaning  
TMDS Data1-  
Pin  
Meaning  
9
17 TMDS Data0-  
2
10 TMDS Data1+  
11 TMDS Data 1/3 Shield  
12 not connected  
13 not connected  
14 +5V Power  
18 TMDS Data0+  
19 TMDS Data 0/5 Shield  
20 not connected  
21 not connected  
22 TMDS Clock Shield  
23 TMDS Clock+  
24 TMDS Clock-  
3
TMDS Data 2/4 Shield  
not connected  
4
5
not connected  
6
DDC Clock  
7
DDC Data  
15 Earth  
8
Analogue Vertical Sync  
16 Hot Plug Detect  
A26361-K1143-Z120-1-7619, edition 3  
29  
 

HP Hewlett Packard Compaq TFT 2025 User Manual
Franke Consumer Products Cooktop FPL 606 User Manual
Electrolux Thermaline 9CHG584146 User Manual
Electrolux EKM6044 User Manual
D Link VoiceCenter DPH 128MS User Manual
Dell MD3200I User Manual
Briggs Stratton 92500 User Manual
Black Box Computer Hardware KV1722A User Manual
AT T 8243 User Manual
Addonics Technologies ADS3GX4R5 E User Manual