Fisher Paykel Cooktop CG903MLD User Manual

Installation instructions  
IZONA CookSurface  
CG903ML & CG903MLD models  
NZ AU  
Important!  
SAVE THESE INSTRUCTIONS  
The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please visit our  
local website listed at the end of this document or contact your local Fisher & Paykel dealer.  
1
SAFETY AND WARNINGS  
Before you install the appliance, please make sure that  
WARNING!  
the local distribution conditions (nature of gas and pressure) and the adjustment of the appliance  
are compatible. For adjustment conditions for this appliance, see ‘Gas rate summary’  
a suitable disconnection switch is incorporated in the permanent wiring, mounted and positioned to  
comply with the local wiring rules and regulations. A means of disconnection with at least a 3 mm  
air gap contact separation in all poles must be incorporated into the ꢀxed wiring in accordance with  
the wiring rules, unless the local wiring rules allow for alternative means  
the appliance is connected to a 220V - 240V 50Hz (10 A) power supply only and earthed via the  
power supply cable  
Electrical shock hazard  
Disconnect appliance from main power supply before continuing.  
Failure to do so could result in electrical shock or death.  
WARNING!  
there is a power outlet within reach of the power supply cable (900 mm from the centre rear of the  
product). This must be accessible after installation. The power supply cable should not touch any  
metal parts  
Cut hazard  
if the power supply cable is damaged, it is replaced only by the special cable: Part no. 531953 - Flex  
Terminal Block Assy NZ/AU, obtainable from authorised Fisher & Paykel Service Agents  
the supply connection point (gas shut-oꢁ valve) is accessible after installation  
the benchtop is made of a heat resistant material  
Take care - panel edges are sharp.  
Failure to use caution could result in injury or cuts.  
the installation complies with all the requirements of Australian and New Zealand Gas Installation  
Standards (AS5601, NZS5261), including that the product has to be installed so that the surface  
temperature of any nearby combustible surface will not exceed 65 OC above ambient. See 3  
‘Clearance Dimensions.  
Important safety precautions!  
Particular attention shall be given to the relevant requirements regarding ventilation.  
Please make this information available to the person installing the appliance as it could reduce your  
installation costs.  
When you install the appliance  
This appliance is to be installed and connected to the electricity and gas supply only by an authorised  
person.  
Installation must comply with your local building and local gas authority codes and electricity  
regulations.  
Failure to install the appliance correctly could invalidate any warranty or liability claims.  
This gas appliance is suitable for connection to natural gas only. If in doubt, refer to the local gas  
network operator or gas supplier to conꢀrm gas type at installation site.  
We do not recommend you ꢂush mount or seal this appliance into the bench with silicone or glue.  
Doing so will make future servicing diꢃcult. Fisher & Paykel will not be liable for any costs associated  
with removing or replacing a sealed-in appliance, nor for repairing any damage that may be incurred  
by doing this.  
Seal exposed bare edges of the cutout with an oil-based paint or moisture-proof polyurethane to  
prevent possible moisture creeping between the cooktop trim and the benchtop.  
We do not recommend the use of a down-draught extractor fan with the appliance, as it may distort  
the ꢂame pattern, causing uneven heating and reduced cooking performance.  
Where this appliance is installed in marine craft or in caravans, it shall not be used as a space heater.  
No combustible material or products should be placed on this appliance at any time.  
Do not spray aerosols in the vicinity of this appliance while it is in operation.  
If, after following the instructions given, the appliance cannot be adjusted to perform correctly,  
please refer to the Service & Warranty book for warranty details and your nearest Authorised Service  
4
5
PARTS SUPPLIED  
3
Wok stand (1)  
Flexible  
hose (1)  
Blue washer (1)  
Elbow  
/
“ NPT (1)  
Clamping  
brackets (4)  
and screws (4)  
NG regulator (1)  
Air intake  
grill (1) and  
screws (6)  
8
GAS RATE SUMMARY  
All appliances are factory set for natural gas and are not currently convertable to LPG.  
NZ AU  
SMALL  
MEDIUM  
WOK  
NG (1.0 kPa)*  
NG  
NG  
NG  
CG903ML &  
CG903MLD  
1.09Y  
7.2  
1.15Y  
8.0  
1.65  
12.8  
*Nominal pressure with the two smaller burners on High.  
6
FLUSH MOUNTING INSTALLATION (NOT RECOMMENDED)  
view from below  
A
C
E
B
WARNING!  
B
x 4  
C
A
D
We do not recommend ꢁush  
mounting and sealing as servicing  
requires the CookSurface to be  
removed from the benchtop. The  
owner carries all risk for ꢀush  
mounting the CookSurface.  
The owner must ensure the  
F
G
E
M
CookSurface has been cut out  
from the benchtop before  
L
Reꢀt existing  
screw to secure  
into basepan  
K
I
servicing can be carried out. Fisher  
& Paykel will not be liable for any  
costs associated with removing  
or replacing a ꢁush-mounted  
and/or sealed-in product, nor for  
repairing any damage that may be  
incurred by doing this.  
2
1
20-50 mm  
H
5 mm  
Fresh air from  
outside cabinetry  
For benchtops thicker than  
50 mm, reverse the clamping  
brackets, as shown in 11  
Top view  
D
M
J
1
2
H
HI  
II  
I
Ensure silicone does  
N
not leak underneath glass.  
3
min. 150 OC rated  
Product and cabinetry dimensions (mm)  
Apply tape/foam  
inside recess to stop  
silicone leaking underneath.  
overall height of product (including dials/pan supports)  
96  
96  
900  
530  
94  
A
B
C
D
E
F
G
H
HI  
I
II  
J
K
L
M
N
overall width of product  
900  
410  
94  
overall depth of product  
F
height of chassis (below top of bench)  
TO REMOVE PRODUCT  
width of chassis  
856  
384  
424  
905  
865  
415  
390  
max. 10  
64  
856  
480  
480  
905  
865  
535  
494  
depth of chassis  
2
depth of chassis  
tted elbow)  
overall width of routered recess  
width of cutout  
overall depth of routered recess  
depth of cutout  
corner radius of cutout  
max. 10  
64  
1
distance from top of bench to centre of gas inlet on product  
distance from edge of chassis to gas inlet on product  
corner radius of routered recess  
20  
20  
max. 2  
5
max. 2  
5
height of routered recess  
7
8
REMOVE FROM PACKAGING  
ENSURE THERE IS ADEQUATE AIR SUPPLY  
A
A
500 mm  
50 mm  
The CookSurface requires adequate air supply to fully function. The base of the CookSurface must have direct  
unrestricted ventilation to the room where the CookSurface is installed. Do not ventilate the base area to an  
external area that can be at diꢁerent air pressure to that of the burners. You may ventilate from adjacent  
cupboards, but ensure that the available air supply will not be restricted. The ventilation area must be  
500 x 50 mm or of an equivalent area. If the 50 mm wide slot is not possible due to the width of the available toe  
recess, increase the length of the slot so as to maintain an equivalent area of 250 cm2. An air intake grill is provided.  
Ensure that the grill is not covered or obstructed.  
9
10  
FIT THE ELBOW & FLEXIBLE HOSE  
LOWER GENTLY INTO THE CUTOUT  
A
A
Important!  
The ꢀexible hose supplied  
1
must be used to enable servicing.  
2
NPT  
1
Ensure there is enough  
ꢀexible hose looped to  
allow for removing  
2
PTFE  
1
appliance for servicing.  
11  
12  
SECURE THE PRODUCT TO THE BENCHTOP  
CONNECT TO THE GAS & ELECTRICAL SUPPLY  
A
view from below  
B
A
NG  
x 4  
Ensure the blue washer is ꢂtted  
½“ BSP  
For benchtops thicker than 50 mm,  
reverse the clamping brackets, as shown  
Reꢂt existing  
screw to secure  
into basepan  
Reꢂt existing  
screw to secure  
into basepan  
NG  
2
2
1
1
Fresh air from  
outside cabinetry  
Fresh air from  
outside cabinetry  
20-50 mm  
50+mm  
13  
14  
CHECK FOR GAS LEAKS  
TEST OPERATION  
A
A
Test operation by  
lighting all burners.  
1
2
3
4
GAS  
GS  
ON  
15  
FINAL CHECKLIST  
Installer’s name:  
TO BE COMPLETED BY THE INSTALLER  
Have you installed the clamping brackets?  
Installer’s signature:  
Installation company:  
Date of installation:  
Have you allowed for adequate air supply to the product?  
Have you used the supplied ꢁexible hose and blue washer?  
Have you leak-tested all connections?  
Is the regulator set to the correct working pressure?  
Have you placed the supplied duplicate data plate on an adjacent surface?  
Is the CookSurface earthed?  
LEAVE THESE INSTRUCTIONS WITH THE CUSTOMER  
Check that the power supply cable is NOT touching the CookSurface.  
OPERATION:  
Do all burners ignite both individually and in combination?  
Are the ꢁames consistent and appropriately sized?  
Have you demonstrated the basic operation to the customer?  

HP Hewlett Packard L1755 User Manual
Hobart CG731 User Manual
GE General Electric Cooktop ZEU30R User Manual
GE DECT 28165xx2 User Manual
Extron electronic Extron Electronics Computer Hardware RGB 118 PLUS User Manual
Eizo FlexScan L778 User Manual
DoubleSight Displays Computer Monitor DS 1900WA User Manual
Curtis TC924 User Manual
Asus A7V133 M User Manual
Acer AL 1911 User Manual