Instruction Manual
EN-75080C / EN-75084C
8” / 8.4” Compact Size
TFT-LCD MONITOR
SAFETY INSTRUCTION …………………………………………………………………..
CAUTIONS ………………………………………………………………..........................
FCC RF INTERFERENCE STATEMENT ……………………………...........................
CONNECTING WITH EXTERNAL EQUIPMENT ……………………………………….
CONTROLS AND FUNCTIONS …………………………………………………………..
2 ~ 3
4
5
6
7 ~ 24
MOUNTING GUIDE ……………………………………………………………………….. 25 ~ 26
D-SUB CONNECTOR PIN ASSIGNMENTS …………………………………………….
POWER MANAGEMENT ………………………………………………………………….
SPECIFICATIONS ………………………………………………………………………….
TROUBLE SHOOTING GUIDE …………………………………………………………...
27
28
29
30
INSTRUCTION MANUAL ……………………………………………………………………. 1
Important Safety Instruction
1. Read these instructions.
2. Keep these Instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers,stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug.
Apolarized plug has two blades with one wider than the other.
Agrounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician for replacement of the
bsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles and the point where they exit from the apparatus.
11. Only use attachment/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or sold with
the apparatus. When a cart is used, use caution when moving
the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused
for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or
moisture does not operate normally or has been dropped.
2 ……………………………………………………………………. INSTRUCTION MANUAL
- The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids,
such as vases, shall be placed no the apparatus.
- Minimum distances(e.g. 10cm) around the apparatus for sufficient ventilation.
“WARNING - To reduce the risk of fire or electric shock, do not expose the apparatus to rain or moisture.”
“The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids,
such as vases, shall be placed on the apparatus.”
This symbol is intended to alert the user to the presence of uninsulated :
dangerous voltage with in the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating
and maintenance(servicing) instructions in the literature accompanying the
appliance.
INSTRUCTION MANUAL ……………………………………………………………………. 3
CAUTION
The power supply cord is used as the main disconnect device, ensure that the socket-outlet is
located/installed near the equipment and is easily accessible.
ATTENTIONN
Le cordon d`alimentation est utillsé comme interrupteur général. La prise de courant doit être
située ou installée à proximité du matériel et être facile d`accès
NEVER REMOVE THE BACK COVER
Removal of the back cover should be carried out only by qualified personnel.
DO NOT USE IN HOSTILE ENVIRONMENTS
To prevent shock or fire hazard, do not expose the unit to rain or moisture.
This unit is designed to be used in the office or home. Do not subject the unit to vibrations,
dust of corrosive gases.
KEEP IN A WELL VENTILATED PLACE
Ventilation holes are provided on the cabinet to prevent the temperature from rising.
Do not cover the unit or place anything on the top of unit.
AVOID HEAT
Avoid placing the unit in direct sunshine or near a heating appliance.
TO ELIMINATE EYE FATIGUE
Do not use the unit against a bright back ground and where sunlight or other light sources will
shine directly on the monitor.
BE CAREFUL OF HEAVY OBJECT
Neither the monitor itself nor any other heavy object should rest on the power cord.
Damage to a power cord can cause fire or electrical shock.
4 ……………………………………………………………………. INSTRUCTION MANUAL
NOTE
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio, TV technician for help.
- Only shielded interface cable should be used.
Finally, any changes or modifications to the equipment by the user not expressly approved by
the grantee or manufacturer could void the users authority to operate such equipment.
DOC COMPLIANCE NOTICE
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital
apparatus set out in the radio interference regulation of Canadian Department of
communications.
INSTRUCTION MANUAL ……………………………………………………………………. 5
A. BACK
1. TRIGGER INPUT
Sensor Signal Input
2. AUDIO IN
3.5Φ STEREO IN
3. S-VIDEO IN
Y/C separated signal input
4. AV1 OUT
Video looping output for AV1
5. AV1 IN
Composite signal Input for AV1
6. AV2 OUT
Video looping output for AV2
7. AV2 IN
Composite signal Input for AV2
8. VGA
PC Analog Signal Input
6 ……………………………………………………………………. INSTRUCTION MANUAL
B. FRONT
1. INPUT
Select input source.
2. MENU
Activates and exits the On Screen Display.
This button can also be used to move previous menu or status.
OSD MENU(MAIN) : Input Source, Screen, Audio, OSD, Color, Utility, Exit.
3/4. ▲ / ▼
This button allows user to enter the sub-menu of the activated function
▼ : Auto geometry adjustment in PC Source.
5/6. ◀ / ▶
Adjust the volume / Adjust menu settings.
7. POWER ON/OFF
Turns the power ON or OFF. There will be a few seconds delay before the display appears.
8. POWER LED
The power LED(next to the power switch) lights with green when the power is turned ON.
The power is turned off by pressing the power switch again and the power LED goes to Red.
INSTRUCTION MANUAL ……………………………………………………………………. 7
OSD Menu Description
A: CUSTOM MENU (For AV1, AV2 & S-Video Input)
1) Press the MENU button and then press the up(▲) or down(▼) button to select the Custom.
2) Press the up(▲) or down(▼) button to select the sub menu.
3) Press the left(◀) or right(▶) button to adjust the picture setting.
4) Press the MENU button to save.
Brightness: Increase or decrease the intensity of the image.
Contrast: Increase or decrease the intensity (lightness or dimness) of the image.
Color: Increase or decrease the colour of the picture.
Tint: Increase or decrease the tint of the picture.
Sharpness: Increase or decrease the sharpness of the picture.
A: CUSTOM MENU (PC Input)
1) Press the MENU button and then press the up(▲) or down(▼) button to select the Custom.
2) Press the up(▲) or down(▼) button to select the sub menu.
3) Press the left(◀) or right(▶) button to adjust the picture setting.
4) Press the MENU button to save.
8 ……………………………………………………………………. INSTRUCTION MANUAL
B. Picture / Sound Menu (For AV1, AV2 & S-Video)
1. Picture Mode
1) Press the MENU button and then press the up(▲) or down(▼) button to select the Picture / Sound.
2) Press the right(▶) or INPUT button.
3) Press the up(▲) or down(▼) button to select the Picture Mode.
4) Press the right(▶) or INPUT button.
5) Press the up(▲) or down(▼) button to select the Picture Mode option.
6) Press the MENU button to save
2. Color Tone
1) Press the up(▲) or down(▼) button to select the Color Tone.
2) Press the right(▶) or INPUT button.
3) Press the up(▲) or down(▼) button to select the Color Tone option.
4) Press the MENU button to save.
INSTRUCTION MANUAL ……………………………………………………………………. 9
3. Mute
1) Press the up(▲) or down(▼) button to select the Mute.
2) Press the right(▶) or INPUT button.
3) Press the up(▲) or down(▼) button to select the On or Off.
4) Press the MENU button to save.
4. Volume
1) Press the up(▲) or down(▼) button to select the Volume
2) Press the left(◀) or right(▶) button to adjust Volume setting.
3) Press the MENU button to save.
10 ……………………………………………………………………. INSTRUCTION MANUAL
5. Size
1) Press the up(▲) or down(▼) button to select the Size
2) Press the right(▶) or INPUT button.
3) Press the up(▲) or down(▼) button to select the Size option.
4) Press the MENU button to save.
6. NR
1) Press the up(▲) or down(▼) button to select the NR.
2) Press the right(▶) or INPUT button.
3) Press the up(▲) or down(▼) button to select the On or Off.
4) Press the MENU button to save.
INSTRUCTION MANUAL ……………………………………………………………………. 11
7. 3D Comb
1) Press the up(▲) or down(▼) button to select the 3D Comb.
2) Press the right(▶) or INPUT button.
3) Press the up(▲) or down(▼) button to select the On or Off.
4) Press the MENU button to save.
8. Camera 540
3) Press the up(▲) or down(▼) button to select the Camera 540 menu.
4) Press the right(▶) or INPUT button.
5) Press the up(▲) or down(▼) button to select the Camera 540 option.
6) Press the MENU button to save.
12 ……………………………………………………………………. INSTRUCTION MANUAL
B. Picture / Sound Menu (For PC Input)
1. Picture Mode
1) Press the MENU button and then press the up(▲) or down(▼) button to select the Picture/Sound.
2) Press the right(▶) or INPUT button.
3) Press the up(▲) or down(▼) button to select the Picture Mode.
4) Press the right(▶) or INPUT button.
5) Press the up(▲) or down(▼) button to select the Picture Mode option.
6) Press the MENU button to save.
2-1. Color Tone
1) Press the up(▲) or down(▼) button to select the Color Tone.
2) Press the right(▶) or INPUT button.
INSTRUCTION MANUAL ……………………………………………………………………. 13
3) Press the left(▶) or INPUT button again.
4) Press the up(▲) or down(▼) button to select the Color Tone option.
5) Press the MENU button to save.
2-2. Color Tone (Custom)
1) Press the up(▲) or down(▼) button to select the Custom in the Color Tone.
2) Press the Menu button to save.
14 ……………………………………………………………………. INSTRUCTION MANUAL
3) Press the up(▲) or down(▼) button to select the Red(R), Green(G) or Blue(B).
4) Press the left(◀) or right(▶) button to adjust color density.
5) Press the MENU button to save.
4. PC control (Only PC Input)
1) Press the up(▲) or down(▼) button to select the PC.
2) Press the right(▶) or INPUT button.
3) Press the up(▲) or down(▼) button to select the PC sub menu.
4) Press the right(▶) or INPUT button.
5) Press the left(◀) or right(▶) button to adjust the PC setting.
6) Press the MENU button to save.
Auto Adjust: Auto geometry adjustment.
Phase: Adjust the number of horizontal picture elements.
H-Position: Move image horizontally on screen right or left.
V-Position: Move image vertically on screen up or down.
Frequency: Adjust the vertical noise of screen image.
INSTRUCTION MANUAL ……………………………………………………………………. 15
C. SETUP MENU
1) Press the MENU button and then press the up(▲) or down(▼) button to select the Setup.
1. Reset
1) Press the right(▶) or INPUT button
2) Press the right(▶) or INPUT button again.
3) Press INPUT button to execute the reset.
Reset: All settings go to the factory initialization.
16 ……………………………………………………………………. INSTRUCTION MANUAL
2. Language
1) Press the up(▲) or down(▼) button to select the Language.
2) Press the right( ) or INPUT button.
3) Press the up(▲) or down(▼) button to select language.
4) Press the MENU button to save.
3. OSD Tone
1) Press the up(▲) or down(▼) button to select the OSD Tone.
2) Press the right( ) or INPUT button
3) Press the up(▲) or down(▼) button to select the OSD Tone option.
4) Press the MENU button to save.
INSTRUCTION MANUAL ……………………………………………………………………. 17
4. Blue Screen
1) Press the up(▲) or down(▼) button to select the Blue Screen.
2) Press the right( ) or INPUT button.
3) Press the up(▲) or down(▼) button to select the On or Off.
4) Press the MENU button to save.
5. Key Lock
1) Press the up(▲) or down(▼) button to select the Key Lock.
2) Press the right( ) or INPUT button
3) Press the up(▲) or down(▼) button to select the On or Off
4) Press the MENU button to save.
※ How to unlock
1) On the front key: Press the INPUT and MENU button at the same time over 3 seconds.
2) On the Remote Controller: The Remote Controller operates well because the Key Lock
function is only allowed for the front key of this product.
18 ……………………………………………………………………. INSTRUCTION MANUAL
6. Trigger
1) Press the up(▲) or down(▼) button to select the Trigger.
2) Press the right( ) or INPUT button.
6-1. Trigger Enable
1) Press the up(▲) or down(▼) button to select the Trigger Enable.
2) Press the right( ) or INPUT button.
3) Press the up(▲) or down(▼) button to select the On or Off.
4) Press the Menu button to save.
INSTRUCTION MANUAL ……………………………………………………………………. 19
6-2. Trigger Input
1) Press the up(▲) or down(▼) button to select the Trigger Input .
2) Press the right( ) or INPUT button.
3) Press the up(▲) or down(▼) button to select the Trigger Input option.
4) Press the Menu button to save.
6-3. Buzzer
1) Press the up(▲) or down(▼) button to select the Buzzer.
2) Press the right( ) or INPUT button.
3) Press the up(▲) or down(▼) button to select the On or Off.
4) Press the Menu button to save.
20 ……………………………………………………………………. INSTRUCTION MANUAL
6-4. Trigger Time
1) Press the up(▲) or down(▼) button to select the Trigger Time.
2) Press left( ) or right( ) button to adjust Trigger Time setting.
3) Press the MENU button to save.
6-5 Trigger Option
1) Press the up(▲) or down(▼) button to select the Trigger Option.
2) Press the right( ) or INPUT button.
3) Press the up(▲) or down(▼) button to select the Trigger Option setting.
4) Press the Menu button to save.
N/C (Normal Closed): When Trigger cable is opened, Trigger function is activated.
N/O (Normal Opened): When Trigger cable is closed, Trigger function is activated.
High: When Trigger signal is high(2~5[V]), Trigger function is activated.
Low: When Trigger signal is low(0~0.6[V]), Trigger function is activated.
INSTRUCTION MANUAL ……………………………………………………………………. 21
7. Auto switching
1) Press the up(▲) or down(▼) button to select the Auto switching.
2) Press the right( ) or INPUT button.
7-1. Auto switching On/Off
1) Press the right( ) or INPUT button.
3) Press the up(▲) or down(▼) button to select the On or Off .
4) Press the Menu button to save.
22 ……………………………………………………………………. INSTRUCTION MANUAL
7-2. Auto switching Inputs enabled
1) Press the up(▲)or down(▼) button to select the Inputs enabled.
2) Press the right( ) or INPUT button.
3) Press the up(▲) or down(▼) button to select the Input.
4) Press the right( ) or INPUT button.
5) Press the up(▲) or down(▼) button to select the On or Off and then press the Menu button to save.
INSTRUCTION MANUAL ……………………………………………………………………. 23
7-3. Auto switching Time
1) Press the up(▲) or down(▼) button to select the Time.
2) Press the left(◀) or right(▶) button to adjust the Time and then press the MENU button to save.
24 ……………………………………………………………………. INSTRUCTION MANUAL
A. Wall mount(Optional)
1) Using the 75 mm VESA holes.
2) Using the VESA standard wall mount design and the 75mm hole pattern on the back side
to install the LCD monitor to the wall.
TRIGGER
INPUT
AUDIO
IN
75mm
S-VIDEO
IN
IN
AV1
OUT
IN
AV2
OUT
VGA
DC12V
INSTRUCTION MANUAL ……………………………………………………………………. 25
B. Rack mount(Optional)
1) Install the monitor in the Pre-Rack using the 75 mm VESA holes.
2) Install the Pre-Rack in the Open Rack using side mounting holes.
※ The Pre-Rack is available rotation of 360° on the Open Rack.
26 ……………………………………………………………………. INSTRUCTION MANUAL
▶ PIN ASSIGNMENTS
Pin 1
RED VIDEO
9
2
GREEN VIDEO
BLUE VIDEO
GROUND
10
11
12
13
14
15
SIGNAL CABLE DETECT
GROUND
3
4
5
6
7
8
SDA(for DDC)
GROUND
H-SYNC.(or H+V SYNC.)
V-SYNC.
RED GROUND
GREEN GROUND
BLUE GROUND
SCL(for DDC)
ACCESSORY
1. POWER CORD
2. USER’S MANUAL
3. PC cable
4. Adaptor
5. Trigger Cable(Option)
6. Wall mount (Option)
7. Rack mount (Option)
INSTRUCTION MANUAL ……………………………………………………………………. 27
This monitor features a power management system to “power down” upon receipt of the VESA
DPMS(The display power management signaling) from a VESA DPMS video card.
The VESA DPMS-compliant video card performs this signaling system through not sending
horizontal, vertical, or sync signal.
This monitor enters an appropriate mode through identifying each of the three modes of the
signaling system.
POWER CONSUMPTION
MODE
ON
POWER CONSUMPTION
< 21W
< 20.5W
< 20.5W
< 9.5W
STANDBY
SUSPEND
ACTIVE OFF
LED INDICATOR
The power management feature of the monitor is comprised of four stages: On(Green),
Standby, Suspend, Active off(Red on/off 1 sec) and Unsupported mode(Green).
MODE
ON
LED COLOR
MONITOR OPERATION
Normal Operation
GREEN
STANDBY
SUSPEND
ACTIV OFF
Screen blanks after preset idle time
And some electronic circuits or all
Circuitry in the monitor shut down.
RED ON/OFF
1 SEC
UNSUPPORTES
MODE
Normal operation but the on screen
Display will show error massage
GREEN
RED
POWER OFF
Not Operation
28 ……………………………………………………………………. INSTRUCTION MANUAL
8RTC
8RTF’
8’’ Diagonal AM-TFT(Active-Matrix)
8.4’’ Diagonal AM-TFT(Active-Matrix)
Pixel pitch(mm) : 0.2025(H) x 0.2025(V) Pixel pitch(mm) : 0.213(H) x 0.213(V)
LCD-Type
BRIGHTNESS: 250cd/㎡(Typical)
CONTRAST RATIO: 500:1(Typical)
RESPONSE TIME: 25msec(Typical)
800X600 @60Hz
BRIGHTNESS: 600cd/㎡(Typical)
CONTRAST RATIO: 600:1(Typical)
RESPONSE TIME: 25msec(Typical)
RESOLUTION
(H x V)
HORIZONTAL: 37.5KHz, VERTICAL: 60Hz
FREQUENCY
VIDEO(2ch input 1.0Vp-p, 75Ω terminated, loop-through out)
SYNC(Separate TTL Level)
INPUT SIGNAL
S-VIDEO(1ch input (Y/C))
3.5Φ Stereo Sound
ACTIVE DISPLAY
AREA (H x V)
162mm x 121.5mm
170.4mm X 127.8mm
PACKING
DIMENSIONS
(W x D x H)
215.3mm x 40.4mm x 184.3mm
215.3mm X 40.4mm X 184.3mm
Net Weight : 1.1Kg
Gross Weight : 2.25Kg
DC 12V/ 3.33A
Net Weight : 1.19Kg
Gross Weight : 2.34Kg
DC 12V/ 3.33A
WEIGHT
ELECTRICAL
RATINGS
▶▶ NOTE :
Technical specifications are subject to change without notice.
INSTRUCTION MANUAL ……………………………………………………………………. 29
WEEE Symbols
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other
European countries with separate collection systems)
This marking shown on the product or its literature,
indicates that it should not be disposed with other
household wastes at the end of its working life. To
prevent possible harm to the environment or human
health from uncontrolled waste disposal, please
separate this from other types of wastes and
recycle it responsibly to promote the sustainable
reuse of material resources. Household users should
contact either the retailer where they purchased this
product, or their local government office, for details of
where and how they can take this item for
environmentally safe recycling. Business users
should contact their supplier and check the terms
and conditions of the purchase contract. This product
should not be mixed with other commercial wastes
for disposal.
30 ……………………………………………………………………. INSTRUCTION MANUAL
Taiwan - Headquarter Office
12F, No.79 Sec.1 Shin-Tai Wu Road,
Hsi-Chi, Taipei, Taiwan
China - Beijing Office
Room 609,Technology Trade Building.
Shangdi Information Industry Base,
Haidian District,Beijing China
Tel: +86-10-62971096
Tel: +886-2-26982334
Fax: +886-2-26982380
Fax: +86-10-62971423
Europe - Germany Office
Albert-Einstein-Strasse 1,
D-46446 Emmerich, Germany
Tel: +49-2822-9394-0
Japan Office
1809 WBG Marive East 18F,
2-6 Nakase, Mihama-ku,
Chiba City 261-7118, Japan
Tel: +81-43-212-8188
Fax: +81-43-297-0081
Fax: +49-2822-939495
USA - California Office
1801 Highland Ave. Unit A
Duarte, CA 91010 ,U.S.A
Tel: +1-626-844-8888
USA - New York Office
415 Oser Ave Unit S
Hauppauge, NY 11788
Sales: +1-631-436-5070
Fax: +1-631-436-5027
Fax: +1-626-844-8838
Ihr
entwickelt und hergestellt mit qualitativ
hochwertigen Materialien und
Komponenten, die recycelt und wieder
verwendet werden können.
EverFocus
Produkt
wurde
Your EverFocus product is designed
and manufactured with high quality
materials and components which can
be recycled and reused.
This symbol means that electrical and
electronic equipment, at their end-of-
life, should be disposed of separately
from your household waste.
Dieses
Symbol
bedeutet,
dass
elektrische und elektronische Geräte
am Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Please, dispose of this equipment at
your
local
community
waste
Bitte entsorgen Sie dieses Gerät bei
collection/recycling centre.
Ihrer
örtlichen
kommunalen
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Sammelstelle oder im Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!
P/N: L39ME0138 Rev.2
|