Epson A882459 User Manual

EPSON®  
14" Super VGA  
Color Monitor-  
(Models A882441 and A882459)  
User’s Guide  
FCC COMPLIANCE STATEMENT  
FOR AMERICAN USERS  
This equipment has been tested and found to comply with the limits for a class B digital  
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in a residential installation. This  
equipment generates, uses and can radiate radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off and on, the  
user is encouraged to try to correct the interference by one or more of the following  
measures:  
Reorient or relocate the receiving antenna  
q
q
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the  
receiver is connected.  
q
Consult the dealer or an experienced radio/ TV technician for help  
q
NOTICE  
(1) Any changes or modification not expressly approved by the party responsible for  
compliance could void the user’s authority to operate the equipment.  
(2) Shielded interface cables and AC power cord must be used in order to comply with the  
emission limits.  
FOR CANADIAN USERS  
This digital apparatus does not exceed the Class B limits for radio noise emissions from  
digital apparatus as set out in the radio interference regulations of the Canadian  
Department of Communications.  
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites  
applicables aux appareils numériques de Classe B prescrites dans le règlement sur le  
brouillage radioélectrique édicté par le Ministère des Communications du Canada.  
IMPORTANT NOTICE  
DISCLAIMER OF WARRANTY  
Epson America makes no representations or warranties, either express or implied, by or  
with respect to anything in this manual, and shall not be liable for any implied warranties  
ofmerchantability and fitness for a particular purpose or for any indirect, special, or  
consequential damages. Some states do not allow the exclusion of incidental or  
consequential damages, so this exclusion may not apply to you.  
COPYRIGHTNOTICE  
All rights reserved. No part of this publication may be reproduced, stored in a retrieval  
system, or transmitted, in any form or by any means, electronic, mechanical,  
photocopying, recording, or otherwise, without the prior written permission of Epson  
America, Inc. No patent liability is assumed with respect to the use of information  
contained herein. Nor is any liability assumed for damages resulting from the use of the  
information contained herein. Further, this publication and features described herein are  
subject to change without notice.  
TRADEMARKS  
EPSON is a registered trademark of Seiko Epson Corporation  
EPSON Connection is a service mark of Epson America, Inc.  
General notice: Other product names used herein are for identification purposes only and  
may be trademarks of their respective companies.  
The Energy Star emblem does not represent EPA endorsement of any product or service  
Copyright © 1995 by Epson America, Inc.  
Torrance, California, USA  
400508100  
7/ 95  
ii  
Important Safety Instructions  
Although this monitor is designed to assure your safety, improper use can  
cause electric shock or fire hazard. In order not to defeat the safeguards  
incorporated in the monitor, observe the following safety instructions:  
1.  
Read all of these instructions and save them for later reference.  
2. Follow all warnings and instructions in this manual and marked on the  
monitor.  
3. The monitor contains shock hazard potential. Do not attempt to open or  
remove any covers, and do not attempt to service the monitor yourself.  
Refer all servicing to authorized service personnel.  
4. Never push objects of any kind into the monitor through cabinet slots.  
5. Do not expose the monitor to liquids, such as rain or spills.  
6. Do not place the monitor on an unstable cart, stand, or table, and be  
careful not to drop it.  
7. Do not place the monitor near a heating appliance or in direct sunlight.  
Intense heat can damage the monitor’s circuitry.  
8.  
Slots and openings on the top, sides, and back of the cabinet are provided  
for ventilation; do not block or cover these openings. Do not place the  
monitor in a built-in insulator, such as a bookcase, unless proper  
ventilation is provided.  
9. Power supply voltages outside the monitor’s specified line voltage range  
may harm the monitor. The monitor should be operated from the type  
of power source indicated on the rear panel marking label.  
10 Make sure the combined amperage rating for all products plugged into  
the wall outlet used for the monitor does not exceed the amperage  
rating of the wall outlet.  
11 Use only the power cord supplied with the monitor. If you must use  
another power cord, make sure it meets the applicable standards  
(UL/ CSA).  
12 Do not overload the computer inlet and extension cords as this can result  
in fire or electric shock.  
13. Be careful not to damage the power cord or plug  
iii  
14. Do not allow anything to rest on the power cord. Do not place a cord  
where it may be stepped on.  
15. Do not replace the video interface cable with a non-shielded cable  
16. Unplug the monitor from the computer and the wall outlet before  
cleaning. Use a damp cloth for cleaning.  
17. Excessive brightness for long periods may permanently imprint an image  
on the screen.  
18. To avoid picture distortion or color disturbance, do not put devices that  
generate magnetism (such as telephones, televisions, speakers, or  
magnetic screwdrivers) near the monitor.  
19. When the monitor will not be used for a long period of time, turn it off  
by pressing the power button. (Always wait at least five seconds before  
you turn it back on.)  
20. Unplug the monitor from the computer and the wall outlet and refer  
servicing to authorized service personnel under the following  
conditions:  
A. If the power cord or plug is damaged  
B. If the monitor has come into contact with any liquids, such as rain or  
spills.  
C. If the monitor does not operate normally when the operating  
instructions are followed. Adjust only those controls that are  
covered by the operating instructions; improper adjustment of  
other controls may result in damage and will often require  
extensive work by a qualified technician to restore the product to  
normal operation.  
D. If the monitor has been dropped or the cabinet or glass faceplate has  
been damaged.  
E. If the monitor exhibits a distinct change in performance.  
iv  
Contents  
1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
. . . . . . . . . . . . . . . . . . . . .  
Introduction  
1
Energy Star Compliant  
2
. . . . . . . . . . . . . . . . . . . . . . . .  
Where to Get Help  
. . . . . . . . . . . . . . . . . .  
3
Electronic Support Services  
4
4
. . . . . . . . . . . . . . . . . . . . . . .  
. . . . . . . . . . . . . . . . . . . . . . .  
Unpacking the Monitor  
Setting Up the Monitor  
. . . . . . . . . . . . .  
. . . . . . . . . . . . . . .  
. . . . . . . . . . . .  
5
7
7
9
Attaching the Tilt and Swivel Base  
Selecting a Location for the Monitor  
Connecting the Monitor to Your Computer  
. . . . . . . . . . . . . . . . . . . . . .  
Turning On the Monitor  
. . . . . . . . . . . . . . . . . 10  
. . . . . . . . . . . . . . . . . 10  
Accessing the Monitor Controls  
Adjusting the Monitor Controls  
12  
12  
15  
. . . . . . . . . . . . . . . . . . . . . . .  
. . . . . . . . . . . . . . . . . . . . . . . . . . . .  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Cleaning the Monitor  
Troubleshooting  
Specifications  
vii  
Introduction  
Your EPSON® Super VGA Color Monitor (models A882441 and  
A882459) is compatible with all IBM® 8514A, VGA, and Super  
VGA modes from 30 to 50 KHz. It offers the following features:  
o
o
o
14-inch, analog color CRT display with non-glare surface  
and a 13.2-inch viewing area  
High-resolution display of up to 1024 x 768 pixels,  
non-interlaced  
Six user-adjustable controls: brightness, contrast, horizontal  
centering, horizontal size, vertical centering, and vertical  
size  
o
Universal power supply with automatic line voltage  
selection between 100 and 240 volts  
o
o
Energy Star compliant  
Tilt and swivel base.  
This manual describes how to set up and use the monitor. It  
also provides troubleshooting information and specifications.  
Energy Star Compliant  
Your EPSON monitor complies with the U.S. Environmental  
Protection Agency’s Energy Star program, which promotes the  
manufacture of energy-efficient printers, computers, and  
monitors. If your computer is Energy Star compliant, the  
EPSON Super VGA Color Monitor automatically enters a  
low-power, standby mode when the computer stops sending  
input signals to the monitor. The power indicator at the front  
right of the monitor turns amber when the monitor is in this  
low-power state.  
14" Super VGA Color Monitor  
1
The EPA estimates that if all desktop computers, monitors,  
printers, and other peripheral devices met Energy Star  
standards, energy cost savings would exceed $1 billion  
annually and carbon monoxide emissions would be reduced by  
20 million tons.  
The Energy Star emblem does not represent EPA endorsement of any  
product or service.  
Where to Get Help  
If you purchased your monitor outside the United States,  
contact an EPSON representative at the nearest marketing  
location for support and service. International marketing  
locations are listed at the back of this manual.  
If you purchased your monitor in the United States or Canada,  
EPSON provides customer support and service through a  
network of Authorized EPSON Customer Care Centers.  
EPSON also provides the following services when you dial  
(800) 9224911:  
o
Technical assistance with the installation, configuration,  
and operation of EPSON products  
o
Assistance in locating your nearest Authorized EPSON  
Reseller or Service Center  
o
o
o
Customer Relations  
EPSON Technical information library fax service  
Product literature on current and new products.  
You can purchase printed manuals, accessories, or parts for  
EPSON products from EPSON Accessories at (800) 873-7766  
(U.S. sales only). In Canada, call (800) BUY-EPSON.  
2
14" Super VGA Color Monitor  
Electronic Support Services  
If you have a modem, the fastest way to access helpful tips,  
specifications, drivers, application notes, DIP switch or jumper  
settings, and bulletins for EPSON products is through the  
online services below.  
EPSON bulletin board service  
You can call the EPSON Bulletin Board Service (BBS) at  
(310) 782-4531. No membership is required. Make sure your  
communications software is set to 8 data bits with no stop bit, 1  
parity bit, and a modem speed up to 28.8 Kbps. See the  
documentation that came with your communications software  
for more information.  
CompuServe® online support  
CompuServe members can call the Epson America Forum on  
CompuServe. If you are already a member, simply type GO  
EPSON at the menu prompt to reach the Forum.  
If you are not currently a member, you are eligible for a free  
introductory membership as an owner of an EPSON product  
This membership entitles you to:  
o
o
o
An introductory $15 credit on CompuServe  
Your own user ID and password  
A complimentary subscription to CompuServe Magazine,  
CompuServe’s monthly publication.  
To take advantage of this offer, call (800) 848-8199 in the United  
States and Canada and ask for representative #529. In other  
countries, call the following U.S. telephone number:  
(614) 529-1611, or your local CompuServe access number.  
14" Super VGA Color Monitor  
3
Unpacking the Monitor  
When you unpack your monitor, make sure you have these  
items :  
o
o
o
EPSON 14" Super VGA Color Monitor  
AC power cord (to connect the monitor to a wall outlet)  
Tilt and swivel base  
Warranty card  
o
o
Registration card.  
If anything is missing or damaged, contact your EPSON  
representative immediately.  
Be sure to keep the monitor’s original box and packing  
materials in case you need to transport the monitor later.  
Setting Up the Monitor  
This section describes how to attach the tilt and swivel base,  
select a location for the monitor, and connect it to your  
computer.  
4
14" Super VGA Color Monitor  
Attaching the Tilt and Swivel Base  
Before you attach the tilt and swivel base, cover your work area  
with a blanket or foam pad to avoid scratching the monitor.  
Then follow these steps:  
1. Carefully set the monitor face down on the padding so the  
bottom of the monitor is facing you.  
2. Locate the four sets of hooks on the top portion of the base.  
3. Hold the base so the hooks are turned down and position  
the base next to the bottom of the monitor.  
14" Super VGA Color Monitor  
5
4. Insert the hooks into the slots on the monitor.  
5. Slide the base toward the front of the monitor until the base  
clicks into position.  
6. Carefully turn the monitor over so it rests on its base  
Note  
Always remove the tilt and swivel base before packing and  
transporting the monitor. To remove the base, disconnect  
the power cord from the electrical outlet and disconnect the  
video interface cable from the back of the computer.  
Carefully set the monitor face down on a padded surface.  
With the bottom of the monitor toward you, press down on  
the release tab and lift the base to remove the hooks from the  
slots.  
6
14" Super VGA Color Monitor  
Selecting a Location for the Monitor  
Follow these guidelines when you select a location for the  
monitor:  
Read the safety instructions at the beginning of this manual.  
o
o
Use a large, sturdy desk that can support the weight of the  
computer, monitor, and any peripheral devices. The desk  
should also provide ample space to hold your equipment  
and work materials.  
For your comfort, it is best to place the monitor directly in  
front of you and sit about an arm’s length away from it.  
o
o
To minimize glare and reduce eye fatigue, position the  
monitor so that sunlight, desk lamps, or overhead lights do  
not shine directly on the screen.  
o
For comfortable viewing, the top of the screen should be  
slightly below eye level when you are sitting in front of the  
monitor. Your line of sight to the screen should be about  
10° to 20° below the horizontal.  
Connecting the Monitor to Your Computer  
Before you connect the monitor to your computer, make sure  
your computer and video adapter are set up to use with the  
monitor. If necessary, install an appropriate video adapter card  
in your computer and set any DIP switches or jumpers on the  
card to match the monitor. You may also need to change  
jumper settings inside the computer. See your computer or  
video adapter card manual for instructions.  
14" Super VGA Color Monitor  
7
Follow these steps to connect the monitor to your computer:  
1. Make sure the monitor, computer, and any peripheral  
devices are turned off.  
2. Turn the monitor around so its back is facing you.  
3.  
4.  
Plug the end of the video cable into the video  
connector on the back of the computer and tighten the two  
screws on the cable connector.  
Plug one end of the power cord into the monitor’s AC  
receptacle. Plug the other end into a properly grounded  
wall outlet.  
The monitor contains a universal power supply, so you can  
connect it to any wall outlet supplying between 100 and  
240 volts.  
5.  
Turn the monitor around so the screen faces you and use the  
tilt and swivel base to adjust the position of the screen for  
comfortable viewing.  
14" Super VGA Color Monitor  
8
Turning On the Monitor  
Turn on the monitor by pressing the power button located at  
the front right of the monitor. Then turn on the computer. After  
a few seconds, an image appears on the screen.  
The power indicator is green when you first turn on the  
monitor and when the monitor is in the full-power state. When  
the monitor is in the low-power state, the power indicator is  
amber.  
14" Super VGA Color Monitor  
9
Accessing the Monitor Controls  
The image control box contains the image controls for the  
monitor. It is located at the bottom left of the monitor. To access  
the controls, you need to open the control box cover. Place your  
finger at the left side of the cover and pull it gently forward  
until the cover opens.  
Adjusting the Monitor Controls  
The controls on the front of the monitor allow you to adjust the  
display to suit your preferences. The brightness and contrast  
controls at the bottom right of the screen adjust the screen to  
make it clear and easy to read.  
10  
14" Super VGA Color Monitor  
The following table summarizes the functions of the monitor’s  
controls.  
Function  
Control  
Icon  
Centers the image vertically. Turn the  
control clockwise to move the image up:  
turn it counterclockwise to move the  
image down.  
Vertical center  
Adjusts the vertical size of the image. Turn  
the control clockwise to increase the  
height: turn it counterclockwise to  
decrease the height.  
Vertical size  
Centers the image horizontally. Turn the  
control clockwise to move the image to  
the right: turn it counterclockwise to move  
the image to the left.  
Horizontal  
center  
Adjusts the width of the image. Turn the  
control clockwise to increase the width:  
turn it counterclockwise to decrease the  
width.  
Horizontal size  
Contrast  
Adjusts the contrast (the degree of  
difference between the lightest and  
darkest parts of the display). Turn the  
control clockwise to increase the  
contrast: turn it counterclockwise to  
decrease the contrast.  
Adjusts the brightness of the image. Turn  
the control clockwise to increase the  
brightness: turn it counterclockwise to  
decrease the brightness.  
Brightness  
Turns the monitor on and off.  
Power button  
14" Super VGA Color Monitor  
11  
Cleaning the Monitor  
To keep the monitor operating at its best, it is important to  
clean it regularly. Follow these steps:  
1. Turn off the monitor and unplug the power cord from the  
wall outlet. Also disconnect the video interface cable from  
the computer.  
2. Use a damp, lint-free cloth to wipe the monitor casing; do  
not use a wet cloth.  
3. To clean the screen, spray a household glass cleaner on a  
cloth; then wipe the screen.  
Caution  
To avoid electric shock, do not spray cleaner directly on the  
monitor. Do not use solvents, abrasives, or aerosol cleaners  
to clean the monitor; they can discolor the casing or damage  
the anti-glare surface of the screen.  
Troubleshooting  
This section gives solutions to monitor problems you might  
encounter. If these procedures do not solve the problem, see  
page 2 for information on where to get help.  
The power indicator light does not light.  
1. The monitor’s power may not be on. Press the power button.  
2. The power cord might be unplugged or not fully connected.  
Make sure the power cord is properly connected to both the  
monitor and the electrical outlet.  
12  
14" Super VGA Color Monitor  
3. The electrical outlet may not be functional. Test the outlet by  
plugging in a lamp or other device.  
The power indicator is on, but there is no image on the  
screen.  
1. Make sure the computer is turned on.  
2. Make sure the video interface cable is properly connected to  
the monitor and the video interface on the computer. See  
“Connecting the Monitor to Your Computer” on page 7.  
3. Adjust the contrast and brightness controls. See page 11.  
4. The input signals may be outside the monitor’s horizontal  
and vertical frequency ranges (30-50 KHz horizontal and  
50-90 Hz vertical). Make sure the input signals are within  
the specified ranges.  
5. Make sure your computer’s DIP switches, jumpers, and  
setup program settings match the monitor’s settings. If you  
are using a video card, make sure any DIP switches or  
jumpers on the card are set properly. See your computer or  
video adapter card manual for instructions.  
6. Make sure your application program settings are correctly set  
for the monitor.  
The power indicator is amber.  
1. The monitor may be in power management mode. Press any  
computer key or move the mouse to return to normal mode.  
2. Make sure the video interface cable is properly connected to  
the computer’s video interface. See “Connecting the  
Monitor to Your Computer” on page 7.  
14" Super VGA Color Monitor  
13  
3. The input signals may be outside the monitor’s horizontal  
and vertical frequency ranges (30 to 50 KHz horizontal and  
50 to 90 Hz vertical). Make sure the input signals are within  
the specified ranges.  
4. Make sure your computer’s video adapter is set up for use  
with the monitor and that any DIP switches or jumpers in  
the computer or on a video adapter card are set properly.  
See your computer or video adapter card manual for  
instructions.  
The image is not centered or if locks in place on the screen.  
Adjust the H-center and V-center controls on the front of the  
monitor as described on page 11.  
The image is too big or too small for the screen.  
Adjust the H-size and V-size controls on the front of the  
monitor as described on page 11.  
The image is scrambled.  
The input signals may be outside the monitor’s horizontal and  
vertical frequency ranges (30-50 KHz horizontal and 50-90 Hz  
vertical). Make sure the input signals are within the specified  
ranges.  
14  
14" Super VGA Color Monitor  
Specifications  
Model Number  
A882441, A882459  
CRT  
14 inches (356 mm) diagonal  
13.2 inches (335 mm) diagonal  
1024 x 768, non-interlaced  
9.6 x 7.3 inches (245 x 185 mm)  
90°  
Size  
Viewing area  
Resolution  
Display area  
Deflection angle  
Dot pitch  
0.28 mm  
Surface  
Non-glare tinted  
0.35/0.45 mm  
Misconvergence  
Video and Synchronization Signals  
Video  
Analog  
65 MHz  
Bandwidth  
Signal cable  
15-pin, D-sub connector  
30 to 50 KHz  
Horizontal  
frequency  
50 to 90 Hz  
Vertical  
frequency  
14" Super VGA Color Monitor  
15  
D-type connectorpin assignments  
Pin  
Signal  
Pin  
Signal  
Not connected  
Digital GND  
Ground  
Not connected  
H-sync  
Red  
Green  
Blue  
Ground  
Self test  
Red return  
Green return  
Blue return  
1
2
9
10  
11  
12  
13  
14  
15  
3
4
5
6
7
8
V-sync  
Not connected  
Scanning Modes  
Vertical frequency  
70 Hz  
Resolution  
640 x 350  
640 x 400  
640 x 480  
800 x 600  
1024 x 768  
70 Hz  
60/72/75 Hz  
56/60/72/75 Hz  
interlaced/60 Hz  
* Interlaced  
Power Supply  
100-240 VAC, 50/60 Hz, 0.8 A at 120 VAC  
Input voltage  
14" Super VGA Color Monitor  
1 6  
Display Power Management  
Environment Requirements  
40° F to 85° F (5° C to 35° C)  
Operating  
temperature  
Humidity  
8% to 80% noncondensing  
UL, CSA, FCC-B, DHHS  
Safety Standards  
Physical Characteristics  
25 lb (11.3 Kg)  
Net weight  
14 inches (356 mm)  
15.3 inches (387 mm)  
15.9 inches (403 mm)  
Width  
Height  
Depth  
14" Super VGA Color Monitor  
17  
Epson America (USA)  
EPSON Connection  
Tel: (800) 922-8911  
EPSON Accessories  
Tel: (800) 873-7766  
Fax: (310) 782-4401  
Epson America, Inc.  
20770 Madrona Avenue  
Torrance, CA 90509-2842  
Tel: (310) 782-0770  
Epson America (lnternational)  
Epson Latin America  
Miami, FL, USA  
Tel: (305) 265-0092  
Fax: (305) 265-0097  
Epson Mexico, S.A. De C.V.  
Mexico, D.F., Mexico  
Tel: (525) 395-9944  
Hotline: (91800) 50326  
Fax: (525) 395-9499  
Epson Argentina, S.A.  
Buenos Aires, Argentina  
Tel: (541) 322-6898  
Epson Do Brasil  
São Paulo, SP Brazil  
Tel: (5511) 536-0300  
Fax: (5511) 536-9200  
Fax: (541) 322-9725  
Epson Chile, S.A.  
Santiago, Chile  
Tel: (562) 232-8966  
Fax: (562) 233-3197  
Epson Venezuela, S.A  
Caracas, Venezuela  
Tel: (582) 241-0433  
Fax: (582) 241-4561  
Epson Costa Rica, S.A.  
San Jose, Costa Rica  
Tel: (506) 234-6666  
Fax: (506) 225-5709  
Epson Canada Limited  
Willowdale, Ontario, Canada  
Tel: (416) 498-9955  
Fax: (416) 498-4574  
EPSON International Marketing Locations  
Epson Deutschland GmbH  
Zülpicher Straße 6,  
40549 Düsseldorf 11  
Germany  
Epson France S.A.  
B.P. 320, 68 Bis Rue Marjolin  
92305 Levallois-Perret Cedex  
France  
Tel: (49) (211) 56030  
Telex: (41) (211) 504-7787  
Tel: (33) (1) 4087-3737  
Telex: (42) 610657  
Fax: (33) (1) 4737-2240  
Epson Iberica, S.A.  
Avda. de Roma 18-26  
08290 Cerdanyola del valles  
Barcelona, Spain  
Epson Italia s.p.a.  
V.le F.lli Casiraghi, 427  
20099 Sesto, S. Giovanni  
Milano, Italy  
Tel: (34) (3) 582-1500  
Fax: (34) (3) 582-1555  
Telex: 50129  
Tel: (39) (2) 26233  
Fax: (39) (2) 244-0750  
Telex: 315132  
Epson Hong Kong Ltd.  
Rooms 4706-10, 47th Floor  
China Resources Building  
26 Harbour Road  
Epson Australia Pty. Ltd.  
l/ 70 Gibbes Street  
Chatswood 2067 NSW  
Australia  
Wanchai, Hong Kong  
Tel: (852) 585-4600  
Fax: (852) 827-4346  
Tel: (61) (2) 415-9000  
Fax: (61) (2) 417-0077  
Telex: 71-75052  
Telex: 65542 EPSCO HX  
Epson Electronics Trading Ltd.  
Taiwan Branch  
l0F, No. 287, Nanking E. Road,  
Sec. 3, Taipei, Taiwan R.O.C.  
Tel: 886-2-717-7360  
Epson Singapore Pte. Ltd.  
No. 1 Raffles Place #26-00,  
Oub Centre, Singapore 0104  
Tel: (65) 533-0477  
Fax: (65) 533-8119  
Free phone: 886-080-211172  
Telex: 87-39536  
Fax: 886-2-712-9164  
Telex: 785-24444  
Epson (U.K.) Ltd.  
Business Management Dept. (PC)  
Campus 100, Maylands Avenue  
Hemel Hempstead, Hertfordshire,  
HP2 7EZ, UK  
Tel: (44) (442) 227-355  
Free phone: linkline 0800 289622  
Fax: (44) (442) 227-427  
Telex: 51-824767  
Distributors  
South America  
Siser Ltda.  
SISCO  
La Paz, Bolivia  
Tel: (591-2) 34-32-45  
Fax: (591-2) 35-92-68  
São Paulo, SP Brazil  
Tel: (5511) 549-4846  
Fax: (5511) 549-4571  
Merisel Columbia  
Bogota, Columbia  
Tel: (571) 257-7800  
Fax: (571) 610-0674  
McSilver, S.A.  
Bogota, Colombia  
Tel: (571) 270-4303  
Fax: (571) 230-9205  
Ace Computers & Electronics  
Georgetown, Guyana  
Tel: (592) 25-65-48  
C.I.L.D.S.E.  
Quito, Ecuador  
Tel: (593) 2-54-3418  
Fax: (593) 2-55-4780  
Fax: (592) 26-39-67  
Alvimer S.R.L. Trading Inc.  
Ciudad Del Este, Paraguay  
Tel: (595) 61-60234  
A.J. Vierci & CIA  
Asuncion, Paraguay  
Tel: (595) 21-449-220  
Fax: (595) 21-449-514  
Fax: (595) 61-60566  
Control De Procesos Informaticos  
Lima, Peru  
Tel: (5114) 42-3973  
Fax: (5114) 35-5017  
Infocenter  
Asuncion, Paraguay  
Tel: (595) 21-49-862  
Fax: (595) 214-49514  
Interfase S.A.  
Peru Mercantil, S.A.  
Lima, Peru  
Tel: (5114) 62-2566  
Fax: (5114) 61-8256  
Montevideo, Uruguay  
Tel: (598) (2) 49-4600  
Fax: (598) (2) 49-3040  
Caribbean  
Da Costas Limited  
Bridgetown, Barbados  
Tel: (809) 427-5854  
Fax: (809) 436-9870  
Caribbean Computer Systems, Ltd.  
Bridgetown, Barbados  
Tel: (809) 429-7050  
Fax: (809) 427-6509  
WTG/ APTEC Systems Limited  
Kingston, Jamaica  
Computer Business Systems  
Kingston, Jamaica  
Tel: (809) 929-9250  
Fax: (809) 929-8296  
Tel: (809) 925-8600  
Fax: (809) 925-8115  
Computer Gallery  
Hato Rey, Puerto Rico  
Tel: (809) 753-0500  
Fax: (809) 753-0552  
Boolchand Pessomal N.V.  
Curacao, Netherlands Antilles  
Tel: (599) 961-2262  
Fax: (599) 961-4345  
IMCON Limited  
Castries, St. Lucia, West Indies  
Tel: (809) 452-6130  
Micro International, S.A.  
Santo Domingo, Republica Dominicana  
Tel: (809) 533-8110  
Fax: (809) 452-3883  
Fax: (809) 535-3218  
Complete Computer Systems  
Port-of-Spain, Trinidad  
Tel: (809) 625-1204  
Fax: (809) 623-5426  
Central America  
PS2000  
Equipos Electronicos Valdez y Cia  
San Salvador, El Salvador  
Tel: (503) 23-73-43  
Guatemala, Guatemala  
Tel: (502-2) 31-1129  
Fax: (502-2) 31-2449  
Fax: (503) 24-53-82  
CODASA  
Servicio Integral De Computacion, S.A.  
Guatemala, Guatemala  
Tel: (502-2) 31-11-70  
Tegucigalpa, Honduras  
Tel: (504) 33-5685  
Fax: (504) 58-0255  
Fax: (502-2) 32-52-22  
Sonitel, C.A.  
Micro-Tec  
Panama, Republica De Panama  
Tel: (507) 63-98-00  
Fax: (507) 63-98-15  
Managua, Nicaragua  
Tel: (505-2) 66-27-15  
Fax: (505-2) 66-27-58  

HP Hewlett Packard Hewlett Packard Computer Monitor LP2465 24 User Manual
GE 25831 User Manual
Fluke 1750 User Manual
Electrolux 584155 User Manual
Dell Computer Hardware I2200 User Manual
Crestron electronic TPS GA TPI User Manual
Cres Cor CO151FWUA12B User Manual
AT T CL80101 User Manual
AT T 9345 User Manual
AOC LED Monitor E2243FWU User Manual