Epson A881381 User Manual

14” Super VGA  
Color Monitor  
(Models A881381, A881389, and A881371)  
User’s Guide  
(for models A881381 and A881389)  
IMPORTANT NOTICE  
DISCLAIMER OF WARRANTY  
Epson America makes no representations or warranties, either express or implied, by or  
with respect to anything in this manual, and shall not be liable for any implied warranties  
of merchantability and fitness for a particular purpose or for any indirect, special, or  
consequential damages. Some states do not allow the exclusion of incidental or  
consequential damages, so this exclusion may not apply to you.  
COPYRIGHT NOTICE  
AU rights reserved. No part of this publication may be reproduced, stored in a retrieval  
system, or transmitted, in any form or by any means, electronic, mechanical,  
photocopying, recording, or otherwise, without the prior written permission of Epson  
America, Inc. No patent liability is assumed with respect to the use of information  
contained herein. Nor is any liability assumed for damages resulting from the use of the  
information contained herein. Further, this publication and features described herein are  
subject to change without notice.  
TRADEMARKS  
EPSON is a registered trademark of Seiko Epson Corporation.  
EPSON Connection and EPSON Direct are service marks of Epson America, Inc.  
General notice: Other product names used herein are for identification purposes only and  
may be trademarks of their respective companies.  
The Energy Star emblem does not represent EPA  
orsement of any product or service.  
end  
400296900  
2/94  
Copyright © 1994 by Epson America, Inc.  
Torrance, California, USA  
ii  
Important Safety Instructions  
Although this monitor is designed to assure your safety, improper use can  
cause electric shock or fire hazard. In order not to defeat the safeguards  
incorporated in the monitor, observe the following safety instructions:  
1.  
Read all of these instructions and save them for later reference.  
2. Follow all warnings and instructions in this manual and marked on the  
monitor.  
3. The monitor contains shock hazard potential. Do not attempt to open or  
remove any covers, and do not attempt to service the monitor yourself.  
Refer all servicing to authorized service personnel.  
4.  
5.  
6.  
Never push objects of any kind into the monitor through cabinet slots.  
Do not expose the monitor to liquids, such as rain or spills.  
Do not place the monitor on an unstable cart, stand, or table, and be  
careful not to drop it.  
Do not place the monitor near a heating appliance or in direct sunlight.  
Intense heat can damage the monitor’s circuitry.  
7.  
8.  
Slots and openings on the top, sides, and back of the cabinet are provided  
for ventilation; do not block or cover these openings. Do not place the  
monitor in a built-in insulator, such as a bookcase, unless proper  
ventilation is provided.  
9.  
Power supply voltages outside the monitor’s specified line voltage range  
may harm the monitor. The monitor should be operated from the type  
of power source indicated on the rear panel marking label.  
10. Make sure the combined amperage rating for all products plugged into  
the wall outlet used for the monitor does not exceed the amperage  
rating of the wall outlet.  
11. Use only the power cord supplied with the monitor. If you must use  
another power cord, make sure it meets the applicable standards  
(UL/CSA).  
12. Do not overload the computer inlet and extension cords as this can result  
in fire or electric shock.  
13. Be careful not to damage the power cord or plug.  
iii  
Do not allow anything to rest on the power cord. Do not place a cord  
where it may be stepped on.  
14.  
Do not replace the video interface cable with a non-shielded cable.  
15.  
16.  
Unplug the monitor from the computer and the wall outlet before  
cleaning. Use a damp cloth for cleaning.  
Excessive brightness for long periods may permanently imprint an image  
on the screen.  
17.  
18.  
To avoid picture distortion or color disturbance, do not put devices that  
generate magnetism (such as telephones, televisions, speakers, or  
magnetic screwdrivers) near the monitor.  
When the monitor will not be used for a long period of time, turn it off  
by pressing the power button. (Always wait at least five seconds before  
you turn it back on.)  
19.  
20.  
Unplug the monitor from the computer and the wall outlet and refer  
servicing to authorized service personnel under the following  
conditions:  
A. If the power cord or plug is damaged.  
B. If the monitor has come into contact with any liquids, such as rain or  
spills.  
C. If the monitor does not operate normally when the operating  
instructions are followed. Adjust only those controls that are  
covered by the operating instructions; improper adjustment of  
other controls may result in damage and will often require  
extensive work by a qualified technician to restore the product to  
normal operation.  
D. If the monitor has been dropped or the cabinet or glass faceplate has  
been damaged.  
E. If the monitor exhibits a distinct change in performance.  
iv  
Importantes mesures de sécurité  
Bien que le moniteur soit conçu pour assurer votre sécurité, un usage  
incorrect peut provoquer une décharge électrique ou poser un risque  
d’incendie. Pour ne pas aller à l’encontre des mesures de protection  
incorporées dans le moniteur, veuillez bien observer ces instructions:  
1.  
2.  
Lire attentivement les instructions qui suivent Les conserver en lieu sûr.  
Observer les avertissements marqués sur le moniteur et suivre  
rigoureusement les instructions contenues dans le manuel.  
3. Le moniteur pose des risques de décharge électrique. Ne pas tenter de  
soulever ou d’enlever les couvercles; ne pas essayer de réparer le  
moniteur soi-même; s’adresser au personnel de service autorisé par le  
fabricant.  
4.  
Ne jamais rien introduire dans les ouvertures du coffre.  
5. Protéger le moniteur de tout contact avec l’eau, la pluie, les boissons  
renversées, etc.  
6. Ne pas laisser tomber l’appareil. Éviter de le placer sur un meuble instable.  
7.  
Ne pas placer le moniteur  
à
proximité d’un appareil de chauffage, ni en  
plein soleil. La chaleur intense peut endommager les circuits.  
Il est important de ne pas bloquer les ouvertures situées sur le dessus et  
derrière l’appareil: ce sont des prises d’air qui en assurent l’aération. Ne  
8.  
pas placer le moniteur  
d’une bibliothèque fermée,  
d’air.  
à
l’intérieur d’un placard, ou sur les rayons  
à
moins d’y avoir une bonne circulation  
9. Un voltage inférieur ou supérieur  
pour le moniteur pourrait l’endommager. Utiliser seulement la source  
d’électricité indiquée sur l’étiquette l’arriére de l’appareil.  
à
celui qui est spécifiquement désigné  
à
10. L’ampérage total de toutes les pieces branchées sur le même socle ne doit  
pas dépasser la capacité en amperes du socle.  
11.  
Utiliser seulement le cordon électrique dont le moniteur est mum. S’il est  
nécessaire de se servir d’un autre cordon, s’assurer que les standards de  
fabrication sont conform& aux règlements en vigueur (UL/CSA).  
12.  
Ne pas surcharger les prises de courant ni les cordons prolongateurs, car  
cela pourrait mettre le feu ou causer une décharge électrique.  
V
Faire attention  
à
ne pas abîmer le cordon électrique ni la prise de courant.  
13.  
14.  
Ne rien mettre ni laisser sur les cordons électriques. Pour éviter de leur  
marcher dessus, ne pas les installer dâns un endrôit de passage.  
Ne pas remplacer un cordon d’interface par un cordon non protégé.  
15.  
16.  
Debrancher le moniteur du socle et de l’ordinateur avant de le nettoyer.  
Utiliser seulement un chiffon humide.  
Si la luminosité de l’écran reste  
longues pèriodes, l’image pourrait y rester imprimée de façon  
permanente.  
à
sa plus haute intensité pendant de  
17.  
18.  
19.  
20.  
Pour éviter les déformations de l’image ou les perturbations de couleur,  
ne pas placer de sources de magnétisme telles que téléphones, postes de  
television, ou haut-parleurs  
à
proximité du moniteur.  
Lorsqu’on ne devra pas utiliser le moniteur pendant de longues  
périodes, l’eteindre en pressant l’interrupteur. Toujours attendre au  
moins cinq secondes avant de le remettre en marche.  
Débrancher le moniteur et s’adresser au personnel de service autorisé  
darts les conditions suivantes:  
A. Si le cordon est effiloché ou la prise est endommagée  
B. Si le moniteur est entré en contact avec des liquides.  
C. Si le moniteur ne répond pas normalement aux commandes passées  
en suivant les instructions. Ajuster uniquement les contrôles décrits  
dans les instructions; il est possible de gravement endommager  
l’appareil en touchant les autres, ce qui pourrait nécessiter  
l’intervention d’un technicien qualifié pour le remettre en état de  
marche.  
D. Si le moniteur est tombé ou si l’écran ou le coffre ont été  
endommagés.  
E. Si la performance du moniteur est nettement différente de l’ordinaire.  
vi  
Contents  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
. . . . . . . . . . . . . . . . . . . . . . .  
1
1
2
3
4
4
5
7
7
9
9
11  
11  
2 3  
Introduction  
Energy Star Compliant  
. . . . . . . . . . . . . . . . . . . . . . . . . . .  
. . . . . . . . . . . . . . . . . . .  
WheretoGetHelp  
CompuServe On-line Support  
. . . . . . . . . . . . . . . . . . . . . . . . .  
Unpacking the Monitor  
Setting Up the Monitor  
. . . . . . . . . . . . . . . . . . . . . . . . .  
. . . . . . . . . . . . . . . .  
. . . . . . . . . . . . . . .  
. . . . . . . . . . .  
. . . . . . . . . . . . . . . . . . . . . . . .  
Attaching the Tilt and Swivel Base  
Selecting a Location for the Monitor  
Connecting the Monitor to Your Computer  
Turning On the Monitor  
Adjusting the Monitor Controls  
. . . . . . . . . . . . . . . . . . . .  
. . . . . . . . . . . . . . . . . . . . . . . . .  
Cleaning the Monitor  
Troubleshooting  
Specifications  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
vii  
Introduction  
Your EPSON® Super VGA Color Monitor is compatible with all  
IBM® 8514A, VGA, and Super VGA modes from 31 to 35 KHz.  
It offers the following features:  
K
K
14-inch, analog color CRT display  
High-resolution display of up to 1024 x 768 pixels,  
interlaced  
K
Six user-adjustable controls: brightness, contrast, horizontal  
centering, horizontal size, vertical centering, and vertical  
size  
K
K
Universal power supply with automatic line voltage  
selection between 100 and 240 volts  
Tilt and swivel base.  
This manual provides instructions on how to set up and use the  
monitor. It also provides troubleshooting information and  
specifications.  
Energy Star Compliant  
The A881381 and A881389 monitors comply with the U.S.  
Environmental Protection Agency’s Energy Star program,  
which promotes the manufacture of energy-efficient printers,  
computers, and monitors. If your computer is Energy Star  
compliant, the EPSON Super VGA Color Monitor  
automatically enters a low-power, standby mode when the  
computer stops sending certain signals to the monitor. The  
power indicator at the front right of the monitor turns amber  
when the monitor is in this low-power state.  
1
14 ” Super VGA Color Monitor  
The EPA estimates that if all desktop computers, monitors,  
printers, and other peripheral devices met Energy Star  
standards, energy cost savings would exceed $1 billion  
annually and carbon monoxide emissions would be reduced by  
20 million tons.  
The Energy Star emblem does not represent EPA endorsement of any  
product or service.  
Where to Get Help  
If you purchased your monitor outside the United States,  
contact an EPSON representative at the nearest marketing  
location for support and service. International marketing  
locations are listed at the back of this manual.  
If you purchased your monitor in the United States, EPSON  
provides the following support services through the EPSON  
ConnectionSM  
:
K
K
K
Technical assistance with the installation, configuration,  
and operation of EPSON products  
Assistance in locating your nearest Authorized EPSON  
Reseller or Service Center  
Sales of supplies, parts, documentation, and accessories for  
your EPSON products  
K
K
Customer Relations  
EPSON Fax Back technical information service-available  
directly by calling the toll number (310) 782-4214  
K
K
Product literature with technical specifications on current  
and new products  
User group locations.  
14” Super VGA Color Monitor  
2
You can reach the EPSON Connection at (800) 922-8911, or call  
(310) 782-0770 and ask for the EPSON Connection.  
CompuServe® On-line Support  
The fastest way to access helpful tips, specifications, and  
bulletins is through the Epson America Forum on CompuServe.  
If you are not currently a member of CompuServe, you are  
eligible for a free introductory membership as an owner of an  
EPSON product. This membership entitles you to:  
K
K
K
An introductory $15 credit on CompuServe  
Your own user ID and password  
A complimentary subscription to CompuServe Magazine,  
CompuServe’s monthly publication.  
To take advantage of this offer, call (800) 848-8199 in the United  
States and Canada and ask for representative #529. In other  
countries, call (614) 529-1611 or your local CompuServe access  
number.  
If you are already a CompuServe member, simply type  
GO EPSON at the menu prompt to reach the Epson America  
Forum.  
3
24” Super VGA Color Monitor  
Unpacking the Monitor  
When you unpack your monitor, make sure you have these  
items:  
K
K
K
EPSON 14” Super VGA Color Monitor  
AC power cord (to connect the monitor to a wall outlet)  
Video interface cable (to connect the monitor to your  
computer)  
K
Tilt and swivel base  
K Warranty card  
K Registration card.  
If anything is missing or damaged, contact your EPSON  
representative immediately.  
Be sure to keep the monitor’s original box and packing  
materials in case you need to transport the monitor later.  
Setting Up the Monitor  
This section describes how to attach the tilt and swivel base,  
select a location for the monitor, and connect the monitor to  
your computer.  
14  
Super VGA CoIor Monitor  
4
Attaching the Tilt and Swivel Base  
Before you attach the tilt and swivel base, cover your work area  
with a blanket or foam pad to avoid scratching the monitor  
during assembly. Then follow these steps:  
1.  
Carefully set the monitor face down on the padding so the  
bottom of the monitor is facing you.  
2.  
Locate the four sets of hooks on the top portion of the base.  
14” Super VGA Color Monitor  
5
3. Hold the base so the hooks are turned down and position  
the base next to the bottom of the monitor.  
4. Insert the hooks into the slots on the monitor.  
5. Slide the base toward the front of the monitor until the latch  
clicks into the locked position. Then turn the monitor over  
so it rests on the base.  
Note  
Always remove the tilt and swivel base before packing and  
transporting the monitor. To remove the base, disconnect  
the power cord from the electrical outlet and disconnect the  
cables from the back of the monitor. Carefully set the  
monitor face down on a padded surface. While pressing the  
latch on the bottom of the monitor, remove the base by  
lifting the hooks out of the slots.  
6
14  
Super VGA Color Monitor  
Selecting a Location for the Monitor  
Follow these guidelines when you select a location for the  
monitor:  
K
K
Read the safety instructions at the beginning of this manual.  
Use a large, sturdy desk that can support the weight of the  
computer, monitor, and any peripheral devices. The desk  
should also provide ample space to hold your equipment  
and work materials.  
K
K
For your comfort, it is best to place the monitor directly in  
front of you and sit about an arm’s length away from it.  
To minimize glare and reduce eye fatigue, position the  
monitor so that sunlight, desk lamps, or overhead lights do  
not shine directly on the screen.  
K
For comfortable viewing, the top of the screen should be  
slightly below eye level when you are sitting in front of the  
monitor. Your line of sight to the screen should be about  
10° to 20° below the horizontal.  
Connecting the Monitor to Your Computer  
before you connect the monitor to your computer, make sure  
your computer and video adapter are set up to use with the  
monitor. If necessary, install an appropriate video adapter card  
in your computer and set any DIP switches or jumpers on the  
card to match the monitor. You may also need to change  
jumper settings inside the computer. See your computer or  
video adapter card manual for instructions.  
14” Super VGA Color Monitor  
7
Follow these steps to connect the monitor to your computer:  
Make sure the monitor, computer, and any peripheral  
devices are turned off.  
1.  
2.  
3.  
Turn the monitor around so the back of the monitor is  
facing you.  
Plug the video interface cable into the VGA connector  
shown below. Tighten the two screws on the cable  
connector.  
Plug the other end of the video cable into the video  
connector on the back of the computer. Then tighten the  
two screws on the cable connector.  
4.  
Plug the power cord into the AC receptacle on the back of  
the monitor.  
5.  
6.  
Plug the other end of the power cord into a properly  
grounded wall outlet.  
14  
Super VGA Color Monitor  
8
The monitor contains a universal power supply, so you can  
connect it to any wall outlet supplying between 100 and  
240 volts.  
Turning On the Monitor  
Turn on the monitor by pressing the power button located at  
the front right of the monitor. Then turn on the computer. After  
a few seconds, an image appears on the screen. To make the  
image on the screen clear and easy to read, use the brightness  
and contrast controls.  
The power indicator is green when you first turn on the  
monitor and when the monitor is in the full-power state. When  
the monitor is in the low-power state, the power indicator is  
amber.  
9
14” Super VGA Color Monitor  
Adjusting the Monitor Controls  
The controls on the front of the monitor allow you to adjust  
the display to suit your preferences. The following table  
summarizes the functions of the monitor’s controls.  
Control  
Icon  
Function  
Vertical center  
Centers the image vertically. Turn the  
control clockwise to move the image up;  
turn it counterclockwise to move the  
image down.  
Vertical size  
Adjusts the vertical size of the image. Turn  
the control clockwise to increase the  
height: turn it counterclockwise to  
decrease the height.  
Horizontal  
center  
Centers the image horizontally. Turn the  
control clockwise to move the image to  
the left; turn it counterclockwise to move  
the image to the right.  
Horizontal size  
Contrast  
Adjusts the width of the image. Turn the  
control clockwise to increase the width;  
turn it counterclockwise to decrease the  
width.  
Adjusts the contrast (the degree of  
difference between the lightest and  
darkest parts of the display). Turn the  
control clockwise to increase the  
contrast; turn it counterclockwise to  
decrease the contrast.  
Brightness  
Adjusts the brightness of the image. Turn  
the control clockwise to increase the  
brightness turn it counterclockwise to  
decrease the brightness,  
Power button  
Turns the monitor on and off.  
I
14” Super VGA Color Monitor  
10  
Cleaning the Monitor  
To keep the monitor operating at its best, it is important to  
clean it regularly. Follow these steps:  
1. Turn off the monitor and unplug the power cord from the  
wall outlet. Also disconnect the video interface cable from  
the computer.  
2. Use a damp, lint-free cloth to wipe the monitor casing; do  
not use a wet cloth.  
3. To clean the screen, spray a household glass cleaner on a  
cloth; then wipe the screen.  
Caution  
To avoid electric shock, do not spray cleaner directly on the  
monitor. Do not use solvents, abrasives, or aerosol cleaners  
to clean the monitor; they can discolor the casing or damage  
the surface of the screen.  
Troubleshooting  
This section gives solutions to monitor problems you might  
encounter. If these procedures do not solve the problem, see  
page 2 for information on where to get help.  
The power indicator light does not light.  
1. The monitor’s power may not be on. Press the power button.  
2. The power cord might be unplugged or not fully connected.  
Make sure the power cord is properly connected to both the  
monitor and the electrical outlet.  
24” Super VGA Color Monitor  
11  
The electrical outlet might be dead. Test the outlet by  
plugging in a lamp or other device.  
3.  
The power indicator is on, but there is no image on the  
screen.  
1.  
Make sure the computer is turned on.  
2.  
Make sure the video interface cable is properly connected to  
the monitor and the video interface on the computer. See  
“Connecting the Monitor to Your Computer” on page 7.  
3. Adjust the contrast and brightness controls. See page 10.  
4.  
The input signals may be outside the monitor’s horizontal  
and vertical frequency ranges (31-35 KHz horizontal and  
56-87 Hz vertical). Make sure the input signals are within  
the specified ranges.  
Make sure your computer’s DIP switches, jumpers, and  
setup program settings match the monitor’s settings. If you  
are using a video card, make sure any DIP switches or  
jumpers on the card are set properly. See your computer or  
video adapter card manual for instructions.  
5.  
6. Make sure your application program settings are correctly  
set for the monitor.  
The image is not centered or if locks in place on the screen.  
Adjust the H-center and V-center controls on the front of the  
monitor as described on page 10.  
The image is too big or too small for the screen.  
Adjust the H-size and V-size controls on the front of the  
monitor as described on page 10.  
12  
24” Super VGA Color Monitor  
The image is scrambled.  
The input signals may be outside the monitor’s horizontal and  
vertical frequency ranges (31-35 KHz horizontal and 56-87 Hz  
vertical). Make sure the input signals are within the specified  
ranges.  
Specifications  
Model Numbers  
A881381, A881389, and A881371  
CRT  
Size  
14 inches (356 mm) diagonal  
1024 x 768  
Resolution  
Display area  
Deflection angle  
Dot pitch  
9.6 x 7 inches (245 x 180 mm)  
90°  
0.28 mm (A881381 and A881389)  
0.39 mm (A881371)  
Non-glare (A881381 and A881389)  
Surface  
0.35/0.5 mm (A881381 and A881389)  
0.6/0.7 mm (A881371)  
Misconvergence  
Video and Synchronization Signals  
Analog  
Video  
45 MHz  
bandwidth  
Signal cable  
15-pin, D-sub connector  
23  
14” Super VGA Color Monitor  
Physical Characteristics  
Weight  
Width  
Height  
Depth  
22.9 lb (10.4 Kg)  
14.2 inches (361 mm)  
15.2 inches (386 mm)  
13.8 inches (351 mm)  
15  
14” Super VGA Color Monitor  
Epson America (USA)  
Epson America, Inc.  
20770 Madrona Avenue  
Torrance, CA 90509-2842  
Tel: (310) 782-0770  
(800) 289-3776  
Fax: (310) 782-5051  
EPSON Connection  
Tel: (800) 922-8911  
EPSON DirectSM  
P.O. Box 2858  
20770 Madrona Avenue  
Torrance, CA 90509-1111  
(800) 374-7300 (Technical support and sales)  
(310) 782-5478 (Sales)  
Tel:  
Fax: (310) 782-4455 (Technical support and sales)  
Epson America (International)  
Epson Mexico, S.A. De C.V.  
Epson Latin America  
Miami, FL, USA  
Tel: (305) 265-0092  
Fax: (305) 265-0097  
Mexico, D.F., Mexico  
Tel: (525) 395-9897  
Fax: (525) 395-9499  
Epson Do Brasil  
Epson Argentina, S.A.  
Buenos Aires, Argentina  
Tel: (541) 322-7487  
Fax: (541) 322-4637  
São Paulo, SP Brazil  
Tel: (5511) 813-3044  
Fax: (5511) 210-9290  
Epson Venezuela, S.A.  
Caracas, Venezuela  
Tel: (582) 241-0433  
Fax: (582) 241-6515  
Epson Chile, S.A.  
Santiago, Chile  
Tel: (562) 232-8966  
Fax: (562) 233-3197  
Epson Canada Limited  
Willowdale, Ontario, Canada  
Tel: (416) 498-9955  
Epson Costa Rica, S.A.  
San Jose, Costa Rica  
Tel: (506) 34-6666  
Fax: (506) 25-5709  
Fax: (416) 498-4574  
Epson International Marketing Locations  
Epson Deutschland GmbH  
Zülpicher Straße 6,  
4000 Düsseldorf 11  
Germany  
Phone: 21l-56030  
Telex: 41-8584786  
Epson France S.A.  
B.P. 320,68 Bis Rue Marjolin  
92305 Levallois-Perret Cedex  
France  
Phone: 33-14737-3333  
Telex: 42-610657  
Epson Iberica, S.A.  
Avda. de Roma 18-26  
08290 Cerdanyola del valles  
08036 Barcelona, Spain  
Phone: 3-582-15-00  
Fax: 3-582-15-55  
Epson Italia s.p.a.  
V.le F.lli Casiraghi, 427  
20099 Sesto S. Giovanni  
Milano, Italy  
Phone: 2-262331  
Fax: 2-2440641 or 2-2440750  
Telex: 315132  
Telex: 50129  
Epson Hong Kong Ltd.  
25/F., Harbour Centre,  
25 Harbour Road  
Epson Australia Pty. Ltd.  
17 Rodborough Road  
Frenchs Forest, N.S.W. 2086  
Australia  
Phone: 2-452-0666  
Fax: 2-451-0251  
Telex: 71-75052  
Wanchai, Hong Kong  
Phone: 831-4600  
Fax: 572-5792  
Telex: 65542 EPSCO I-IX  
Epson Electronics Trading Ltd.  
Taiwan Branch  
pore Pte. Ltd.  
Place #26-00,  
Oub Centre, Singapore 0104  
Phone: 533-0477  
Telex: 87-39536  
Epson Sin  
No. 1 Raffles  
10F, No. 287, Nanking E. Road,  
Sec. 3, Taipei, Taiwan R.O.C.  
Phone: 886-2-717-7360  
Free phone: 886-080-211172  
Fax: 886-2-712-9164  
Telex: 785-24444  
Epson (U.K.) Ltd.  
Business Management Dept. (PC)  
Campus 100, Maylands Avenue  
Hemel Hempstead, Hertfordshire,  
HP27EZ,UK  
Phone: 0442 61144  
Free phone: linkline 0800 289622  
Fax: 0422 227227  
Telex: 51-824767  
Distributors  
South America  
SISCO  
Siser Ltda.  
La Paz, Bolivia  
São Paulo, SP Brazil  
Tel: (5511) 574-8877  
Fax: (5511) 572-1306  
Tel: (591-2) 3432-45  
Fax: (591-2) 35-92-68  
McSilver, S.A.  
Exhibit Computer  
Bogota, Colombia  
Tel: (57l) 218-2700  
Fax: (571) 218-5370  
Bogota, Colombia  
Tel: (571) 230-1014  
Fax: (571) 230-9205  
C.I.L.D.S.E.  
UPEN Computer Systems  
Bogota, Colombia  
Tel: (571) 257-7800  
Quito, Ecuador  
Tel: (593) 2-54-3418  
Fax: (593) 2-55-4780  
A.J. Vierci & CIA  
Ace Computers & Electronics  
Georgetown, Guyana  
Tel: (592) 25-65-48  
Asuncion, Paraguay  
Tel: (595) 21-449-220  
Fax: (595) 21-449-234  
Fax: (592) 26-39-67  
Alvimer S.R.L. Trading Inc.  
Ciudad Del Este, Paraguay  
Tel: (595) 61-60234  
Infocenter  
Asuncion, Paraguay  
Tel: (595) 214-98762  
Fax: (595) 214-49514  
Fax: (595) 61-60566  
Control De Procesos Informaticos  
Lima, Peru  
Tel: (5114) 328-384  
Fax: (5114) 355-017  
Peru Mercantil, S.A.  
Lima, Peru  
Tel: (5114) 62-2566  
Fax: (5114) 61-8256  
Interfase S.A.  
Montevideo, Uruguay  
Tel: (598) 249-4600  
Fax: (598) 249-3040  
Caribbean  
Caribbean Computer Systems, Ltd.  
Bridgetown, Barbados  
Tel: (809) 429-7050  
Da Costas Limited  
Bridgetown, Barbados  
Tel: (809) 427-5854  
Fax: (809) 436-9870  
Fax: (809) 427-6089  
North Atlantic Data Systems  
Hamilton, Bermuda  
Tel: (809) 295-7111  
The Computer Center  
Nassau, Bahamas  
Tel: (809) 328-0304  
Fax: (809) 328-0307  
Fax: (809) 292-3834  
Columbus Limited  
Compusupplies, Ltd.  
Kingston, Jamaica  
Tel: (809) 925-8382  
Fax: (809) 925-8115  
Grand Cayman, West Indies, B.W.I.  
Tel: (809) 949-8039  
Fax: (809) 949-7537  
WTG/APTEC Systems Limited  
Kingston, Jamaica  
Boolchand Pessomal N.V.  
Curacao, Netherlands Antilles  
Tel: (599) 961-7545  
Tel: (809) 929-9250  
Fax: (809) 929-8296  
Fax: (599) 961-7876  
Computer Gallery  
Hato Rey, Puerto Rico  
Tel: (809) 753-0500  
Fax: (809) 753-0552  
Micro Internacional, S.A.  
Santo Domingo, Republica Dominicana  
Tel: (809) 533-7096  
Fax: (809) 535-3218  
IMCON Limited  
Complete Computer Systems  
Port-of-Spain, Trinidad  
Tel: (809) 625-1204  
Castries, St. Lucia, West Indies  
Tel: (809) 452-6130  
Fax: (809) 452-3883  
Fax: (809) 623-5426  
Central America  
Equipos Electronicos Valdez y Cia  
San Salvador, El Salvador  
Tel: (503) 23-73-43  
PS2000  
Guatemala, Guatemala  
Tel: (502-2) 32-57-44  
Fax: (502-2) 31-24-49  
Fax: (503) 24-53-82  
Servicio Integral De Computacion, S.A. CODASA  
Guatemala, Guatemala  
Tel: (502-2) 31-11-70  
Fax: (502-2) 32-52-22  
Tegucigalpa, Honduras  
Tel: (504) 33-5685  
Fax: (504) 58-0255  
Micro-Tee  
Sonitel, C.A.  
Managua, Nicaragua  
Tel: (505-2) 66-27-15  
Fax: (505-2) 66-27-58  
Panama, Republica De Panama  
Tel: (507) 63-98-00  
Fax: (507) 63-98-15  

HP Hewlett Packard Hewlett Packard Computer Keyboard TFT7600 User Manual
Fujitsu Computer Monitor B17 3 User Manual
Dell UltraSharp 2005FPW User Manual
Dell ST2310B User Manual
Daewoo DTQ 25S2FCV User Manual
Cypress CY7C1312AV18 User Manual
Asus M2N8 VMX User Manual
Arcam Amplifiers P90 User Manual
Analog Devices Inc Computer Hardware ADSP 21535 E KIT LITE User Manual
Acer AC713B 17 User Manual