Before operating the monitor, please read this manual thoroughly. This manual
should be retained for future reference.
FCC Class B Radio Frequency Interference Statement
WARNING: (FOR FCC CERTIFIED MODELS)
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
NOTICE:
1. The changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
2. Shielded interface cables and AC power cord, if any, must be used in order
to comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modification to this equipment. It is the
responsibilities of the user to correct such interference.
WARNING:
To prevent fire or shock hazard, do not expose the monitor to rain or moisture.
Dangerously high voltages are present inside the monitor. Do not open the
cabinet. Refer servicing to qualified personnel only.
2
PRECAUTIONS
Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen
sink, laundry tub, swimming pool or in a wet basement.
Do not place the monitor on an unstable cart, stand, or table. If the monitor
falls, it can injure a person and cause serious damage to the appliance. Use
only a cart or stand recommended by the manufacturer or sold with the
monitor. If you mount the monitor on a wall or shelf, use a mounting kit
approved by the manufacturer and follow the kit instructions.
Slots and openings in the back and bottom of the cabinet are provided for
ventilation. To ensure reliable operation of the monitor and to protect it from
overheating, be sure these openings are not blocked or covered. Do not
place the monitor on a bed, sofa, rug, or similar surface. Do not place the
monitor near or over a radiator or heat register. Do not place the monitor in a
bookcase or cabinet unless proper ventilation is provided.
The monitor should be operated only from the type of power source indicated
on the label. If you are not sure of the type of power supplied to your home,
consult your dealer or local power company.
The monitor is equipped with a three-pronged grounded plug, a plug with a
third (grounding) pin. This plug will fit only into a grounded power outlet as a
safety feature. If your outlet does not accommodate the three-wire plug, have
an electrician install the correct outlet, or use an adapter to ground the
appliance safely. Do not defeat the safety purpose of the grounded plug.
Unplug the unit during a lightening storm or when it will not be used for long
period of time. This will protect the monitor from damage due to power
surges.
Do not overload power strips and extension cords. Overloading can result in
fire or electric shock.
Never push any object into the slot on the monitor cabinet. It could short
circuit parts causing a fire or electric shock. Never spill liquids on the monitor.
Do not attempt to service the monitor by yourself; opening or removing
covers can expose you to dangerous voltages and other hazards. Please
refer all servicing to qualified service personnel.
To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked between
100 - 240V AC, Min. 5A.
The wall socket shall be installed near the equipment and shall be easily
accessible.
3
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitor and do not indicate a
problem.
NOTES
•
Due to the nature of the fluorescent light, the screen may flicker during initial
use. Turn off the Power Switch and then turn it on again to make sure the
flicker disappears.
•
•
•
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
The LCD screen has effective pixels of 99.99% or more. It may include
blemishes of 0.01% or less such as a missing pixel or a pixel lit all of the time.
Due to the nature of the LCD screen, an afterimage of the previous screen
may remain after switching the image when the same image has been
displayed for a long time. The monitor will slowly recover from this.
When the screen becomes black or flashing, or cannot illuminate any more,
contact your dealer or service center to replace parts. Don’t repair the screen
by yourself!
•
BEFORE YOU OPERATE THE MONITOR
FEATURES
•
•
•
•
•
558mm diagonal TFT Color LCD Monitor
Crisp, Clear Display for Windows
Recommened Resolutions: 1680 X1050@60Hz
Ergonomic Design
Space Saving, Compact Case Design
CHECKING THE CONTENTS OF THE PACKAGE
The product package should include the following items:
1. LCD Monitor
2. Owner's Manual
3. Power Cord
4. Signal Cable
5. DVI Cable
4
INSTALLATION INSTRUCTIONS
SWIVEL BASE
Install
Remove
Figure 1 Installing and Removing the Swivel Base
POWER CORD
Power Source:
1. Make sure that the power cord is the correct type required in your area.
2. This LCD monitor has an External universal power supply that allows
operation in either 100/120V AC or 220/240V AC voltage area (No user
adjustment is required.)
3. Connect the AC-power cord into your LCD monitor’s power input socket, The
AC-power cord may be connected to either a wall power outlet or the power
outlet socket on your PC, depending on the type of power cord supplied with
your LCD monitor.
5
CONTROLS AND CONNECTORS
SIGNAL CABLE
Connecting the Signal Cable: Plug the Signal Cable one end to LCD monitor’s
“DSUB-Input” socket, the other end to the computer's VGA port and tighten the
two screws on the cable connector.
Connecting the Power Cord: Plug the AC-power cord into the External Adapter.
Then plug the DC-jack power cable into DC-IN Inlet.
Connecting the DVI Cable: Connect one end of the 24-pin DVI cable to the
back of the monitor and connect the other end to the computer’s DVI port.
Caution: If the AC outlet is not grounded (with three holes), install the proper
grounding adapter (not supplied).
Figure 2 Connecting Cables
1. Power input socket
2
DVI input socket
3. D-SUB input socket
6
ADJUSTING THE VIEWING ANGLE
•
•
•
For optimal viewing it is recommended to look at the full face of the monitor,
then adjust the monitor’s angle to your own preference.
Hold the stand so you do not topple the monitor when you change the
monitor’s angle.
You are able to adjust the monitor’s angle from -5° to 20°.
Figure 3
NOTES
•
•
Do not touch the LCD screen when you change the angle. It may cause
damage or break the LCD screen.
Careful attention is required not to catch your fingers or hands when you
change the angle.
7
OPERATING INSTRUCTIONS
GENERAL INSTRUCTIONS
Press the power button to turn the monitor on or off. The other control buttons
are located on the side of the monitor (See Figure 4). By changing these settings,
the picture can be adjusted to your personal preferences.
•
•
•
The power cord should be connected.
Connect the video cable from the monitor to the video card.
Press the power button to turn on the monitor. The power indicator will light
up.
Figure 4
External Control Button
EXTERNAL CONTROLS
1. SOURCE
2. Auto Adjust button / Exit
3. -/Eco mode
4. +/DCR
5. MENU /ENTER
6. Power button
8
FRONT PANEL CONTROL
• Power Button:
Press this button to switch ON/OFF of monitor’s power.
• Power Indicator:
Green — Power On mode.
Orange —Off mode.
• MENU / ENTER :
Active OSD menu or function adjust confirm or Exit OSD menu when in
Contrast /Brightness OSD status.
• SOURCE:
Press this button to switch ON/OFF of DCR.
• -/Eco mode :
Press the Eco key continuously to select the Eco mode when there is
no OSD .
• +/DCR :
Press DCR key continuously to active or disable DCR function when
there is no OSD.
• Auto Adjust button / Exit:
1. When OSD menu is in active status, this button will act as EXIT-KEY
(EXIT OSD menu).
2. When OSD menu is in off status, press this button to activate the Auto
Adjustment function.
The Auto Adjustment function is used to optimized the HPos, VPos,
Clock and Focus.
OSD Lock Function:
To lock the OSD, press and hold the MENU button while the monitor is off and
then press power button to turn the monitor on. To un-lock the OSD - press and
hold the MENU button while the monitor is off and then press power button to
turn the monitor on.
NOTES
•
Do not install the monitor in a location near heat sources such as radiators or
air ducts, or in a place subject to direct sunlight, or excessive dust or
mechanical vibration or shock.
•
•
•
Save the original shipping carton and packing materials, as they will come in
handy if you ever have to ship your monitor.
For maximum protection, repackage your monitor as it was originally packed
at the factory.
To keep the monitor looking new, periodically clean it with a soft cloth.
Stubborn stains may be removed with a cloth lightly dampened with a mild
detergent solution. Never use strong solvents such as thinner, benzene, or
abrasive cleaners, since these will damage the cabinet. As a safety
precaution, always unplug the monitor before cleaning it.
Do not scratch the screen with hard things, it may cause permanent
damage.
•
•
Don’t leak liquid into monitor which will result in the damage of component.
9
HOW TO ADJUST A SETTING
1. Press the MENU-button to activate the OSD window (Figure 5).
2. Press < or > to navigate through the functions. Once the desired function
is highlighted, press the MENU-button to activate it. If the function selected
has a sub-menu, press < or > again to navigate through the sub-menu
functions. Once the desired function is highlighted, press MENU-button to
activate it.
3. Press < or > to change the settings of the selected function.
4. To exit and save, select the exit function. If you want to adjust any other
function, repeat steps 2-3.
Figure 5 The OSD Message
10
ADJUSTING THE PICTURE
The descriptions for function control LEDS
Main
Menu
Icon
Sub
Menu
Item
Main
Menu Item
Sub
Menu
Description
Backlight Adjustment
Brightn
ess
Contra
st
Contrast from Digital-register.
Standard Standard Mode
Text Text Mode
Internet Internet Mode
Game Game Mode
Eco
Luminance
Movie Movie Mode
Sports Sports Mode
Gamma1 Adjust to Gamma1
Gamma2 Adjust to Gamma 2
Gamma3 Adjust to Gamma 3
Gamm
a
Off
On
Disable dynamic contrast ratio
Enable dynamic contrast ratio
DCR
11
Main
Menu
Icon
Sub
Menu
Item
Main
Menu Item
Sub
Menu
Description
Adjust picture Clock to reduce
Vertical-Line noise.
Clock
Focus
Adjust Picture Phase to reduce
Horizontal-Line noise
Image
Setup
H.Posit
ion
Adjust the verticalposition of the
picture.
V.Positi
on
Adjust the horizontal position of the
picture.
Recall Warm Color Temperature
from EEPROM.
Warm
Normal
Cool
Recall Normal Color Temperature
from EEPROM.
Recall Cool Color Temperature
from EEPROM.
Color
Temp.
Recall SRGB Color Temperature
from EEPROM.
sRGB
Red Gain from Digital-register
Green Gain Digital-register.
Blue Gain from Digital-register
Red
Green
Blue
User
12
Main
Menu
Icon
Sub
Menu
Item
Main
Menu Item
Sub
Menu
Description
Full
Enhance
Disable or Enable Full Enhance
Mode
on or off
on or off
on or off
Nature
Skin
Disable or Enable Nature Skin
Mode
Green
Field
Disable or Enable Green Field
Mode
Color
Boost
Disable or Enable Sky-blue
Mode
Sky-blue on or off
AutoDetec
Disable or Enable AutoDetect
Mode
on or off
t
Demo
on or off Disable or Enable Demo
Adjust Frame Size
Frame
Size
Brightnes
s
Adjust Frame Brightness
Adjust Frame Contrast
Contrast
Picture
Boost
H.
position
Adjust Frame horizontal
Position
V.position
Adjust Frame vertical Position
Bright
Frame
on or off Disable or Enable Bright Frame
13
Main
Menu
Icon
Sub
Menu
Item
Main
Menu Item
Sub
Menu
Description
Adjust the verticalposition of
OSD
H.Position
V.Position
Timeout
Adjust the horizontal position of
OSD
OSD
Setup
Adjust the OSD Timeout
Transpare
nce
Adjust the transparence of OSD
Select the OSD language
Language
Select to Auto Detect input
signal
Auto
Input
Select
Select Digital Sigal Source as
Input
DVI
Select Analog Sigal Source as
Input
D-SUB
Auto
Config
Auto adjust the picture to
default
Extra
Image
Ratio
Select wide or 4:3 format for
display
DDC/CI
Turn ON/OFF DDC/CI Support
Show the information of the
main image and sub-image
source
Informatio
n
Reset
Exit
Reset
Exit
yes or no Reset the menu to default
Exit the main OSD
PLUG AND PLAY
14
Plug & Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the VESA
DDC STANDARD. It allows the monitor to inform the host system of its identity
and, depending on the level of DDC used, communicate additional information
about its display capabilities.
The DDC2B is a bidirectional data channel based on the I²C protocol. The host
can request EDID information over the DDC2B channel.
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO
VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE
PROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL.
This monitor meets the Green monitor standards as set by the Video Electronics
Standards Association (VESA) and The Swedish Confederation Employees
(NUTEK). This feature is designed to conserve electrical energy by reducing
power consumption when there is no video-input signal present. When there is
no video input signal this monitor, following a time-out period, will automatically
switch to an OFF mode. This reduces the monitor's internal power supply
consumption. After the video input signal is restored, full power is restored and
the display is automatically redrawn. The appearance is similar to a "Screen
Saver" feature except the display is completely off. The display is restored by
pressing a key on the keyboard, or clicking the mouse.
15
TECHNICAL SUPPORT (FAQ)
Problem & Question
Possible Solution
*Check if the Power Switch is in the ON
position
Power LED is not on
*Power Cord should be connected
*Check if the PC system is Plug & Play
compatible
*Check if the Video Card is Plug & Play
compatible
*Check if the D-15 plug pin of Video
Cable is bent
*Adjust the Contrast and Brightness
Controls.
No Plug & Play
Picture is fuzzy
Picture bounces or a wave
pattern is present in the picture
*Move electrical devices that may cause
electrical interference.
*Computer Power Switch should be in
the ON position.
*Computer Video Card should be snugly
seated in its slot.
*Make sure monitor’s video cable is
properly connected to the computer.
*Inspect monitor’s video cable and make
sure none of the pins are bent.
*Make sure computer is operational by
hitting the CAPS LOCK key on the
keyboard while observing the CAPS
LOCK LED. The LED should either turn
ON or OFF after hitting the CAPS
LOCK key.
The power LED is ON (orange)
but there’s no video or no
picture.
Missing one of the primary
colors (RED, GREEN, or
BLUE)
*Inspect the monitor’s video cable and
make sure that none of the pins are
bent.
Screen image is not centered or *Adjust pixel frequency (CLOCK) and
sized properly.
Picture has color defects
(white does not look white)
FOCUS or press hot-key (AUTO).
*Adjust RGB color or select color
temperature.
*When the brightness of the screen
lowers after being used for a certain
period and the function of the display is
affected, send it to our authorized service
center for repair.
Poor brightness or contrast
*Use win 95/98/2000/ME/XP shut-down
mode Adjust CLOCK and FOCUS or
perform hot- key (AUTO-key).
Horizontal or vertical
disturbances on the screen
CLOCK (pixel frequency) controls the number of pixels scanned by one
horizontal sweep. If the frequency is not correct, the screen shows vertical
stripes and the picture has not correct width.
16
FOCUS adjusts the phase of the pixel clock signal. With a wrong phase
adjustment the picture has horizontal disturbances in light picture.
For FOCUS and CLOCK adjustment use “dot-pattern” or Win 95/98 shut-down
mode pattern .
17
ERROR MESSAGE & POSSIBLE SOLUTION
NO SIGNAL
1. Check that the signal-cable is properly connected , If the connector is loose,
tighten the connector’s screws.
2. Check the signal-cable’s connection pins for damage.
INPUT NOT SUPPORT
Your computer has been set to unsuitable display mode ,set the computer to
display mode given in the following table.
18
APPENDIX
SPECIFICATIONS
Driving system TFT Color LCD
Viewable
LCD Panel
558mm diagonal
image size
Pixel Pitch 0.282mm(H) × 0.282mm(V)
R,G,B Analog Interface
Video
Digital Interface
Input
Separate Sync. H/V TTL
H-Frequency 31kHz – 80kHz
V-Frequency 56-75Hz
Display Colors
Dot Clock
16.7M Colors
165MHz
Max. Resolution
Plug & Play
1680 x 1050@60Hz
VESA DDC2BTM
≤49W(max)
ON Mode
Power Consumption
OFF Mode ≤2W
D-Sub 15pin
Input Connector
DVI 24pin
Analog:0.7Vp-p(standard),
75 OHM, Positive
Input Video Signal
Digital signal
Horizontal : 473mm
Vertical : 296mm
Maximum Screen Size
Power Source
100~240VAC,47~63Hz
Operating Temp: 0° to 50°C
Storage Temp.: -20° to 60°C
Operating Humidity : 20% to 90%
Environmental
Considerations
Dimensions
505.9(W)x407.7(H)x194.8 (D)mm
4.8kg
Weight (N. W.):
19
• Auto Adjust Button
• -/Eco mode
• DCR/+
• Input Select
• Power Button
Switch
• MENU
• Luminance
• Image Setup
• Color Temp.
• Color Boost
• Picture Boost
• OSD Setup
• Extra
External Controls:
Functions
• Reset
• Exit
49Watts
Power Consumption (Maximum)
Regulatory Compliance
CCC
20
FACTORY PRESET TIMING TABLE
HORIZONTAL
RESOLUTION
VERTICAL
FREQUENCY
STANDARD
FREQUENCY
640x480
640x480
640x480
800x600
800x600
800x600
800x600
1024x768
1024x768
1024x768
1024x768
1280x1024
31.469kHz
60 Hz
37.861kHz
37.500kHz
35.156kHz
37.879kHz
48.077kHz
46.875kHz
48.363kHz
56.476kHz
57.515kHz
60.023kHz
63.981kHz
72 Hz
75 Hz
56 Hz
60 Hz
72 Hz
75 Hz
60 Hz
70 Hz
72 Hz
75 Hz
60 Hz
VGA
SVGA
XGA
SXGA
1280x1024
1280x960
1440x900
1440x900
1680x1050
79.976kHz
60.000kHz
55.935kHz
70.635KHz
65.290kHz
75 Hz
60 Hz
60 Hz
75Hz
60Hz
WXGA
WSXGA
21
CONNECTOR PIN ASSIGNMENT
1
6
5
10
11
15
15 - Pin Color Display Signal Cable
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1.
2.
3.
4.
5.
6.
7.
8.
Red
Green
Blue
Ground
Ground
R-Ground
G-Ground
B-Ground
9.
+5V
Detect Cable
Ground
DDC-Serial Data
H-Sync
V-Sync
10.
11.
12.
13.
14.
15.
DDC-Serial Clock
24 - Pin Color Display Signal Cable
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1.
2.
3.
4.
5.
6.
7.
8.
9.
TMDS Data 2-
TMDS Data 2+
TMDS Data 2/4 Shield
TMDS Data 4-
TMDS Data 4+
DDC Clock
DDC Data
N.C.
TMDS Data 1-
TMDS Data 1+
TMDS Data 1/3 Shield
TMDS Data 3-
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
TMDS Data 3+
+5V Power
Ground(for+5V)
Hot Plug Detect
TMDS Data 0-
TMDS Data 0+
TMDS Data 0/5 Shield
TMDS Data 5+
TMDS Data 5-
TMDS Clock Shield
TMDS Clock +
TMDS Clock -
10.
11.
12.
22
ISO 14001 Certification
ISO 14001 certification is the pattern of certification of the environmental
management system, is the core standard of ISO14000 series of standard
on environmental management.
23
|