Eizo Nanao Computer Monitor CX270 User Manual

Important

Please read PRECAUTIONS, this User’s Manual, and the Setup Guide

(separate volume) carefully to familiarize yourself with safe and

effective usage.

•Please refer to the Setup Guide for basic information ranging from

connection of the monitor to a PC to using the monitor.

•The latest User’s Manual is available for download from our web site:

http://www.eizo.com

Notice for this monitor

Aside from general purposes like creating documents, viewing multimedia content, this product is also suited to

applications such as creations of images and graphics, and digital photo processing, where accurate color reproduction

is a priority.

This product has been adjusted speciﬁcally for use in the region to which it was originally shipped. If the product is

used outside the region, it may not operate as speciﬁed in the speciﬁcations.

This product may not be covered by warranty for uses other than those described in this manual.

The speciﬁcations noted in this manual are only applicable when the following are used:

· Power cords provided with the product

· Signal cables speciﬁed by us

Only use optional products manufactured or speciﬁed by us with this product.

It takes about 7 minutes (under our measurement conditions) for the performance of electrical parts to stabilize. Please

wait 7 minutes or more after the monitor power has been turned on, and then adjust the monitor.

Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and maintain a

stable display.

When the screen image is changed after displaying the same image for extended periods of time, an afterimage may

appear. Use the screen saver or power save function to avoid displaying the same image for extended periods of time.

Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer to

“Cleaning” (page 4)).

The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may appear on

the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994% or higher.

The backlight of the LCD panel has a ﬁxed lifetime. When the screen becomes dark or begins to ﬂicker, please contact

your local EIZO representative.

Do not press on the panel or edge of the frame strongly, as this may result in display malfunctions, such as interference

patterns, etc. If pressure is continually applied to the panel, it may deteriorate or damage your panel. (If the pressure

marks remain on the panel, leave the monitor with a black or white screen. The symptom may disappear.)

Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do not attempt

to brush with tissues as this may scratch the panel.

When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation may

occur on the interior and exterior surfaces of the monitor. In that case, do not turn the monitor on. Instead wait until

the dew condensation disappears, otherwise it may cause some damage to the monitor.

Noticeforthismonitor

Cleaning

Attention

• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet or panel,

and also quality deterioration of the image.

• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.

Note

• The optional ScreenCleaner is recommended for cleaning the cabinet and panel surface.

If necessary, the stains on the cabinet and panel surface can be removed by moistening part of a soft cloth with

water.

To use the monitor comfortably

• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor according to

the environmental conditions.

• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.

Noticeforthismonitor

Toresetthecoloradjustments...................... 32

Functions........................................................13

●

DigitalInput(HDMI)........................................15

●

Windows7

......................................................16

WindowsVista................................................16

AdjustingGamma.......................................... 20

Toenable/disableContrastEnhancer............21

AdjustingGain

............................................... 23

SystemRequirement

..................................... 44

Procedure

...................................................... 44

ReducingNoise............................................. 27

CONTENTS

Cover ...................................................................... 1

●

Chapter 3 Setting Monitor ............................... 28

3-1. Enabling/Disabling Mode Selection ......... 28

3-2. Selecting the Language ............................. 28

3-3. Setting Orientation ..................................... 28

Notice for this monitor ......................................... 3

Cleaning .................................................................... 4

To use the monitor comfortabl y ............................. 4

CONTENTS............................................................. 5

3-4. Changing Adjustment Menu Display

Positio n ........................................................ 29

Chapter 1 Introduction....................................... 7

1-1. Features ......................................................... 7

1-2. Controls and Functions ............................... 9

1-3. EIZO LCD Utility Disk...................................10

3-5. Showing and Hiding the EIZO Logo ......... 29

3-6. Locking Operation Button s ....................... 29

3-7 . S etting Signal Bandwidth .......................... 30

3-8. Switching USB Port Automaticall y ........... 30

Diskcontentsandsoftwareoverview............10

●

TouseColorNavigator/ColorNavigator

●

3-9. Changing DUE (Digital Uniformity

Equalizer) Setting ........................................31

Elements........................................................10

1-4. Basic Operations and Functions ...............11

3-10. Reset to defaul t ........................................... 32

BasicAdjustmentmenuoperations...............11

●

ShowingButtonGuide...................................12

●

Toresetalladjustmentstothedefault

●

settings .......................................................... 32

Chapter 2 Adjusting Screen s .......................... 15

2-1. Compatible Resolutions .............................15

Chapter 4 SelfCorrection................................. 33

4-1. Executing SelfCorrection .......................... 33

Chapter 5 Power Saving Functions ................ 34

5-1. Setting Power Save..................................... 34

DigitalInput(DVI-D/DisplayPort)................15

●

2-2. Setting the Resolution ................................16

●

5-2. Enabling/Disabling Automatic

Brightness Adjustmen t .............................. 35

WindowsXP ...................................................16

MacOSX .......................................................16

5-3. Checking the Power Saving Level ............ 35

5-4. Adjusting the Brightness of Indicator...... 35

5-5. Setting DisplayPort Power Save ............... 36

Chapter 6 Troubleshooting.............................. 37

6-1. No picture .....................................................37

6-2. Imaging problems....................................... 38

6-3. Other problem s ........................................... 39

2-3. Adjusting Colo r ............................................17

Toselectthedisplaymode(colormode).......17

●

Toperformadvancedadjustments................18

●

Adjustablesettingsineachmode ..................18

●

AdjustingBrightness......................................19

●

Adjustingthetemperature ..............................19

●

6-4. Built-in correction sensor and

●

AdjustingHue ................................................ 20

AdjustingSaturation .......................................21

SelfCorrection problems ........................... 40

Chapter 7 Reference ........................................ 41

7-1.

Attaching the Optional Arm........................41

Toenhanceoutlineofimage ..........................21

Tosetclipping............................................... 22

7-2. Connecting Multiple External Devices..... 42

Toswitchamonginputsignals ...................... 43

●

Tosetinputsignalselection“Input

●

Adjusting6Colors ......................................... 23

Selection”...................................................... 43

2-4. Expanding Signal Output Range .............. 24

2-5. Selecting Screen Size ................................ 24

7 -3. Making Use of USB (Universal Serial

Bus)............................................................... 44

DVI,DisplayPort(PCsignal)input .................24

●

HDMI(HDsignal)input ................................. 25

●

HDMI(SDsignal)input................................. 25

●

7 -4. Showing Monitor Information.................... 45

2-6. Conﬁguring Moving Image Performance. 26

Displayingsignalinformation“SignalInfo”... 45

●

2-7.

Specifying Color Space ............................. 26

DisplayingMonitorInformation“Monitor

●

Info”............................................................... 45

2-8. Setting HDMI................................................ 27

CONTENTS

7 -5. Speciﬁcations ............................................. 46

Chapter 8 Glossary .......................................... 49

Appendix.............................................................. 51

Trademark ................................................................51

License .....................................................................51

FCC Declaration of Conformity ............................ 52

Hinweise zur Auswahl des richtigen

Schwenkarms für Ihren Monitor........................... 53

Hinweis zur Ergonomie : ....................................... 53

LIMITED WARRANTY............................................. 54

Recycling Information ........................................... 63

China Measures for RoHS Compliance in

ChinaRoHS.............................................................. 67

CONTENTS

Chapter 1 Introduction

1-1. Features

• 27.0″ wide format LCD

• Wide color gamut (Adobe RGB coverage: 97%)

• Applicable to the resolution of 2560 × 1440.

• IPS panel with 178˚ horizontal and vertical viewing angles

• Frame synchronization mode supported (23.75 - 30.5Hz, 47.5 - 61.0Hz)

• 3 signal input terminals (DVI-D × 1, HDMI × 1, DisplayPort × 1)

DisplayPort connector (applicable to 8 bit and 10 bit)^*1

HDMI connector (applicable to 8 bit, 10 bit, and 12 bit)^*1

*1 Not applicable to audio signals.

• Color Mode function

Reproduces a color gamut and gamma compliant with the following standard.

Adobe^®RGB

The Paper mode reproduces a printed paper effect on the monitor.

See “T o select the display mode (color mode)” (page 17).

• Supports portrait and landscape format

• This product is equipped with a built-in correction sensor, and supports SelfCorrection in which the monitor

executes display correction independently.

See “Chapter 4 SelfCorrection” (page 33).

• The “ColorNavigator” color management software enables you to calibrate monitor characteristics and

generate color proﬁles^*2

*2 The color management software “ColorNavigator” is on the CD-ROM for the ColorNavigator Licensed models. See

“1-3. EIZO LCD Utility Disk” (page 10).

• Supports Photo Color Matching Software “ColorNavigator Elements”^*3

This software enables you to adjust the color of the monitor easily while comparing it with a printed picture.

*3 Stored on the CD-ROM for the ColorNavigator non-licensed models. See “1-3. EIZO LCD Utility Disk” (page 10).

• The software “ScreenManager Pro for LCD” to adjust the screen using the mouse and keyboard is included.

This software can be downloaded from our web site (http://www.eizo.com).

• Supports Color Vision Deﬁciency Simulation Software “UniColor Pro”

This software can be downloaded from our web site (http://www.eizo.com).

• Power saving function

Suppressing the power consumption reduces the carbon dioxide emissions. This product is equipped with power saving

function.

0 W when the main power is off

Equipped with main power switch.

Turning off the main power switch completely shuts off power supply to the monitor while the monitor is not used.

Auto EcoView function

The ambient light sensor on the front side of the monitor detects the environmental brightness to adjust the screen

brightness automatically and comfortably. Excessively high brightness may lead a damage to the natural environment

as well as to your eyes. Suppressing the excessively high brightness will be helpful to reduce the power consumption

and the damage to your eyes.

See “5-2. Enabling/Disabling Automatic Brightness Adjustment” (page 35).

• Displays HDCP (High-bandwidth Digital Protection) protected contents.

Chapter1Introduction

Attention

Be careful of the following points when using the built-in correction sensor.

Do not touch the built-in correction sensor.

Itmayreducethemeasurementaccuracyofthebuilt-incorrectionsensor,orresultininjury

orequipmentdamage.

Attention

• A high temperature or high humidity environment may affect the measurement accuracy of the built-in correction

sensor. We suggest storing and using the monitor under the following conditions.

- Temperature 30˚C or less

- Humidity 70% or less

Avoid storing or using the sensor where it may be exposed to direct sunlight.

Note

• This monitor supports both portrait and landscape format. You can change the orientation of the Setting menu when

using the monitor screen in vertical display position. (see “3-3. Setting Orientation” (page 28))

• For using the monitor with “Portrait” position, the graphics board supporting portrait display is required. When placing

the monitor in a “Portrait” position, settings of your graphics board need to be changed. Refer to the User’s Manual of

the graphics board for details.

Chapter1Introduction

1-2. Controls and Functions

Adjustment

menu^*1

10 11

12 1314

Executesdisplaycorrectionforanindependentmonitor.SelfCorrectionfunction

(page33)

1. Built-in correction sensor

2. Ambient Light Sensor

Measuresambientlight.

button

Switchesinputsignalsfordisplay(page43).

ChangesColorMode(page17).

Cancelsthesetting/adjustmentandexitstheAdjustmentmenu.

• Providesthemenuselectionaswellastheadjustmentandsettingofafunction.

• DisplaystheBrightnessmenu(page19).

button

DisplaystheAdjustmentmenu,determinesanitemonthemenuscreen,andsaves

valuesadjusted(page11).

Turnsthepoweronoroff.

Indicatesthemonitor’soperationstatus.

Blue:

Operating

Flashingblue

(2timesforeach):

Inthefollowingcases,thisnotiﬁesthatdisplayre-correction

isrequired.

9. Power Indicator

• WhenthetimerissetinColorNavigator(CALmode)

Orange:

OFF:

Powersavingmode

Mainpower/Poweroff

10. Main power switch

11. Power connector

Turnsthemainpoweronoroff.

Connectsthepowercord.

12. Input signal connectors

Left:DVI-Dconnector/Center:HDMIconnector/Right:DisplayPortconnector

ConnectstheUSBcabletousethesoftwarethatneedsUSBconnection,ortouse

USBhubfunction(page44).

13. USB upstream port

Attention

• By default, USB upstream port 1 is enabled. Connect the cable to USB upstream port 1

ﬁrst.

14. USB downstream port

15. Stand^*2

ConnectsaperipheralUSBdevice.

Usedtoadjusttheheightandangleofthemonitorscreen.

ComplieswithKensington’sMicroSaversecuritysystem.

Coversthemonitorcables.

16. Security lock slot

17. Cable holder

*1 For details, see “1-4. Basic Operations and Functions” (page 11).

*2 An optional arm (or an optional stand) can be attached by removing the stand section (see “7-1. Attaching the Optional Arm”

(page 41)).

Chapter1Introduction

1-3. EIZO LCD Utility Disk

An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The following table shows the disk contents

and the overview of the software programs.

Disk contents and software overview

The disk includes application software programs for adjustment, and User’s Manual. Refer to “Readme.txt” or

●

the “read me” ﬁle on the disk for software startup procedures or ﬁle access procedures.

Contents

A“Readme.txt”or“readme”ﬁle

ColorNavigator^*1

Overview

Windows Macintosh

√

Softwareforcalibratingmonitorcharacteristics

andgeneratingICCproﬁles(forWindows)and

AppleColorSyncproﬁles(forMacintosh).

(APCmustbeconnectedtothemonitorwith

thesuppliedUSBcable.)

√

ColorNavigatorElements^*2

Softwareforadjustingthecolorandbrightness

ofthemonitorwhilecomparingapicture

displayedonthemonitorwithaprintedpicture.

(APCmustbeconnectedtothemonitorwith

thesuppliedUSBcable.)

√

Screenadjustmentpatternﬁles^*3Usedwhenadjustingtheimageoftheanalog

signalinputmanually.IftheScreenAdjustment

UtilityisnotapplicabletoyourPC,usethis

√

patternﬁlestoadjusttheimage.

User’sManualofthismonitor(PDFﬁle)

√

*1 Only ColorNavigator Licensed models

*2 Only ColorNavigator Non-Licensed models

*3 This monitor does not support analog signal input, so these ﬁles are not used.

To use ColorNavigator/ColorNavigator Elements

●

Attention

• If “ColorNavigator License” in the monitor information screen is “Not Registered”, the ColorNavigator license must be

purchased and registered to the monitor. For the purchase of the license, contact your local EIZO representative.

• ColorNavigator Elements can be used without a license.

Refer to the corresponding User’s Manual on the CD-ROM disk in order to install and use the software.

When using this software, you will need to connect a PC to the monitor with the supplied USB cable. For

details of the USB cable connection, see “7-3. Making Use of USB (Universal Serial Bus)” (page 44).

Chapter1Introduction

1-4. Basic Operations and Functions

Basic Adjustment menu operations

●

Displaying Adjustment Menu

1. Press

. The Adjustment menu appears.

Menutitle

Item

Currentmode

Setting

Adjusting/Setting

1. Choose a menu to adjust/set with

, and then press

2. Choose an item to adjust/set with

3. Adjust/set the selected item with

Exiting the software

1. Press

a few times. The Adjustment menu ﬁnishes.

Chapter1Introduction

Showing Button Guide

When you press the front buttons (except the button), the button guide appears next to the button.

●

ButtonGuide

Controlbutton

Note

• The button guide will continue to appear while the Adjustment menu or Mode menu is showing.

• The button guide is displayed differently depending on the selected menu or status.

• In CAL mode, the brightness cannot be adjusted even though the button guide is displayed above the and buttons.

Chapter1Introduction

Functions

●

The following table shows the menus for adjustment and setting items of each menu.

Main Menu

Item

Reference

Color^*1

“2-3.AdjustingColor”(page17)

Brightness

Temperature

Gamma

Advanced

Hue

Settings

Saturation

ContrastEnhancer

OutlineEnhancer

Clipping

Gain

6Colors

“3-10.Resettodefault”(page32)

ColorReset

Execute

SelfCorrection

Screen

“4-1.ExecutingSelfCorrection”(page33)

“2-5.SelectingScreenSize”(page24)

ScreenSize

Overdrive

“2-6.ConﬁguringMovingImage

Performance”(page26)

“2-7 .SpecifyingColorSpace”(page26)

ColorSpace

“2-4.ExpandingSignalOutputRange”(page

24)

RangeExtension

HDMISettings^*2

NoiseReduction

“2-8.SettingHDMI”(page27)

Power

“5-1.SettingPowerSave”(page34)

PowerSave

Manager

“5-2.Enabling/DisablingAutomatic

BrightnessAdjustment”(page35)

AutoEcoView

“5-4.AdjustingtheBrightnessofIndicator”

(page35)

Indicator

“5-3.CheckingthePowerSavingLevel”

(page35)

EcoViewIndex

MenuSettings

“3-2.SelectingtheLanguage”(page28)

“3-3.SettingOrientation”(page28)

Language

Orientation

MenuPosition

“3-4.ChangingAdjustmentMenuDisplay

Position”(page29)

Chapter1Introduction

Tools

“T oswitchamonginputsignals”(page43)

InputSelection

ModePreset

“3-1.Enabling/DisablingModeSelection”(page

28)

DVI

“3-8.SwitchingUSBPortAutomatically”(page30)

USB

Selection

DisplayPort

HDMI

“7-4.ShowingMonitorInformation”(page45)

“3-10.Resettodefault”(page32)

SignalInfo

MonitorInfo

AllReset

*1 The adjustment/settings available on the “Color” menu depend on the selected mode. (See “2-3. Adjusting Color”

(page 17))

*2 This setting can be adjusted with HDMI signal input.

Chapter1Introduction

Chapter 2 Adjusting Screens

2-1. Compatible Resolutions

The monitor supports the following resolutions.

Digital Input (DVI-D / DisplayPort)

●

Vertical scan

Resolution

Applicable Signals

Dot clock

DVI-D

DisplayPort

frequency

60Hz

70Hz

60Hz

30Hz

60Hz

640×480

720×400

VGA

VGATEXT

VESA

√

800×600

1024×768

1280×960

1280×1024

1600×1200

1920×1080

1920×1200

2560×1440

2560×1440^*1

VESA

242MHz

(Max.)

VESACVTRB

SingleLink

VESACVTRB

√

Digital Input (HDMI)

• Video signal

●

VGA / 480i,480p,1080i,720p,1080p: 60 Hz

576i,576p,1080i,720p,1080p: 50 Hz

1080p: 24 Hz, 25 Hz, 30 Hz

AgraphicsboardinconformancewiththeVESAandCEA-861standardsisrequired.

*1 Recommended resolution

Chapter2AdjustingScreens

2-2. Setting the Resolution

When you connect the monitor to the PC and ﬁnd that the resolution is improper, or when you want to change the

resolution, follow the procedure below.

Windows 7

●

1. Right-click the mouse anywhere on the desktop except for icons.

2. From the displayed menu, click “Screen resolution”.

3. On the “Screen Resolution” dialog box, select the monitor.

4. Click “Resolution” to select the desired resolution.

5. Click the “OK” button.

6. When a conﬁrmation dialog box is displayed, click “Keep changes”.

Windows Vista

1. Right-click the mouse anywhere on the desktop except for icons.

●

2. From the displayed menu, click “Personalize”.

3. On the “Personalization” window, click “Display Settings”.

4. On the “Display Settings” dialog box, select the “Monitor” tab and select desired resolution in the

“Resolution” ﬁeld.

5. Click the “OK” button.

6. When a conﬁrmation dialog box is displayed, click “Yes”.

Windows XP

1. Right-click the mouse anywhere on the desktop except for icons.

●

2. From the displayed menu, click “Properties”.

3. When the “Display Properties” dialog box is displayed, click the “Settings” tab and select desired resolution

for “Screen resolution” under “Display”.

4. Click the “OK” button to close the dialog box.

Mac OS X

1. Select “System Preferences” from the Apple menu.

●

2. When the “System Preferences” dialog box is displayed, click “Displays” for “Hardware”.

3. On the displayed dialog box, select the “Display” tab and select desired resolution in the “Resolutions” ﬁeld.

4. Your selection will be reﬂected immediately. When you are satisﬁed with the selected resolution, close the

window.

Chapter2AdjustingScreens

2-3. Adjusting Color

To select the display mode (color mode)

This function allows easy selection of a desired mode according to monitor application.

●

Display Modes

Mode

Purpose

1-User1

Availableforthecolorsettingsaccordingtoyourpreference.

2-User2

3-User3

4-Paper

5-Adobe^®RGB

Producesaprintedpapereffectbydecreasingcontrastandcolortemperature.

SuitableforcolormatchingwithAdobe^®RGBcompatibleperipherals.

SuitableforcolormatchingwithsRGBcompatibleperipherals.

6-sRGB

7-CAL

Displaysthescreenadjustedby“ColorNavigator”colormanagementsoftwareand

“ColorNavigatorElements”photocolormatchingsoftware.

Note

• In CAL mode, ColorNavigator and ColorNavigator Elements can be used for adjustment.

• Available CAL mode differs depending on each input signal.

Attention

• Avoid operating any function of the monitor while using ColorNavigator and/or ColorNavigator Elements. Regarding

ColorNavigator and ColorNavigator Elements, see “T o u se ColorNavigator/ColorNavigator Elements” (page 10).

Example:AtDVIinput

Themodemenu

appears.

1-User1←→2-User2←→3-User3←→4-Paper

7-CAL←→6-sRGB←→5-Adobe^®RGB

Procedure

1. Press

The mode menu appears at the bottom left of the screen.

2. The mode among the list is highlighted in turn each time

is pressed.

You can switch the mode with or while the mode menu is displayed.

Note

• The Adjustment menu and the Mode menu cannot be displayed at the same time.

• You can disable a speciﬁc mode to be selected. For more information, see “3-1. Enabling/Disabling Mode Selection”

(page 28).

• “ScreenManager Pro for LCD” allows you to select the color mode automatically according to the application used (see

“Chapter 3 Auto FineContrast” in the “ScreenManager Pro for LCD” User’s Manual).

Chapter2AdjustingScreens

To perform advanced adjustments

“Color” of the Adjustment menu allows you to conﬁgure and save a separate set of color settings for each

●

mode.

Attention

• It takes about 7 minutes (under our measurement conditions) for the performance of electrical parts to stabilize. Please

wait 7 minutes or more after the monitor power has been turned on, and then adjust the monitor.

• The same image may be seen in different colors on multiple monitors due to their monitor-speciﬁc characteristics. Make

ﬁne color adjustment visually when matching colors on multiple monitors.

Note

• The values shown in “%” or “K” are available only as reference.

• Using the “ScreenManager Pro for LCD” allows you to perform the color adjustment by using the mouse and

keyboard of your PC. The adjusted conditions can be stored as the color data to be read in later. (See “Chapter 4 Color

Adjustment” in the User’s Manual for “ScreenManager Pro for LCD”.)

• Using ColorNavigator enables the monitor adjustment that prioritizes color matching of multiple monitors. For details,

refer to the ColorNavigator User’s Manual.

Adjustable settings in each mode

The adjustable settings depend on the mode. (You cannot select any non-adjustable or non-settable function.)

The adjustments or settings made for each mode are applied to all input signals.

√: Adjustable -: Not adjustable

Color Mode

5-Adobe^®

RGB

Function

1-User1

2-User2 3-User3 4-Paper

6-sRGB

7-CAL

Brightness

√

Temperature

Gamma

Hue

Saturation

ContrastEnhancer

OutlineEnhancer

Clipping

√

Gain

√

6Colors

Chapter2AdjustingScreens

Adjusting Brightness

The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD back

●

panel).

Setting Range

75 cd/m²to 350 cd/m²

Procedure

1. Press or

The Brightness menu appears.

2. Use or for adjustment.

3. Press

to exit.

Attention

• If the entered value cannot be set, the value will appear in magenta. In such a case, change the value.

Note

• Alternatively, you can use “Brightness” under “Color” in the Adjustment menu to adjust it.

• The values shown in “cd/m²” are available only as reference.

Adjusting the temperature

The color temperature can be adjusted.

●

The color temperature is normally used to express the hue of “White” and/or “Black” by a numerical value.

The value is expressed in degrees “K” (Kelvin).

The screen becomes reddish at a low color temperature, and bluish at a high color temperature, like the ﬂame

temperature. The gain preset values are set for each color temperature setting value.

Setting Range

Native, 4000K-10000K (speciﬁed every 100K), Standard

Procedure

1. Choose “Color” from the Adjustment menu, and press

2. Choose “Temperature” from “Color”, and press

3. Use or for adjustment.

4. Press

to exit.

Note

• “Gain” allows you to perform more advanced adjustment (see “Adjusting Gain” (page 23)).

• If you set “Native”, the image is displayed in the preset color of the monitor (Gain: 100% for each RGB).

• When gain is changed, the color temperature is changed to “User”.

• The default setting for each Adobe^®RGB/sRGB mode is set to “Standard”, which is the temperature in conformity with

each standard.

Chapter2AdjustingScreens

Adjusting Gamma

Gamma can be adjusted. The brightness of the monitor varies depending on the input signal, however, the

variation rate is not proportional to the input signal. To keep the balance between the input signal and the

brightness of the monitor is called as “Gamma correction”.

●

Setting Range

1.6-2.7, Standard

Procedure

1. Choose “Color” from the Adjustment menu, and press

2. Choose “Gamma” from “Color”, and press

3. Use or for adjustment.

4. Press

to exit.

Note

• The default setting for each Adobe^®RGB/sRGB mode is set to “Standard”, which is the gamma in conformity with each

standard.

• The gamma curve can be adjusted to L* by using ColorNavigator. For details, refer to the ColorNavigator User’s

Manual.

Adjusting Hue

This function allows you to adjust the hue.

Setting Range

●

-100 to 100

Procedure

1. Choose “Color” from the Adjustment menu, and press

2. Choose “Advanced Settings” from “Color”, and press

3. Choose “Hue”, and press

4. Use or for adjustment.

5. Press

to exit.

Attention

• Using this function may make some color gradations unavailable for display.

Chapter2AdjustingScreens

Adjusting Saturation

This function allows you to adjust color saturation.

Setting Range

●

-100 to 100

Procedure

1. Choose “Color” from the Adjustment menu, and press

2. Choose “Advanced Settings” from “Color”, and press

3. Choose “Saturation”, and press

4. Use or for adjustment.

5. Press

to exit.

Attention

• Using this function may make some color gradations unavailable for display.

Note

• The minimum value (-100) changes the screen to monochrome.

To enable/disable Contrast Enhancer

This feature manages the brightness and gain levels of the backlight to match the image displayed while also

●

improving the sense of contrast of images by correcting gamma values.

Procedure

1. Choose “Color” from the Adjustment menu, and press

2. Choose “Advanced Settings” from “Color”, and press

3. Choose “Contrast Enhancer”, and press

4. Select “On” or “Off” with or

5. Press to exit.

To enhance outline of image

OutlineEnhancer functions to emphasize outline of the images by emphasizing the color difference between

pixels composing the images. This may improve the texture of the material and its feel of the images. On the

contrary, it also functions to reproduce the images smoothly by gradating its outline.

Procedure

1. Choose “Color” from the Adjustment menu, and press

2. Choose “Advanced Settings” from “Color”, and press

3. Choose “Outline Enhancer”, and press

4. Select the display status in the range from -3 to 3 (soft to sharp) with or as desired.

5. Press to exit.

Chapter2AdjustingScreens

To set clipping

●

This function allows you to display the monitor with the colors based on the standard values of the deﬁned

color gamut (such as sRGB). The method of displaying the deﬁned color gamut outside the normal gamut of the

monitor can be set.

Procedure

1. Choose “Color” from the Adjustment menu, and press

2. Choose “Advanced Settings” from “Color”, and press

3. Choose “Clipping”, and press

4. Select “On” or “Off” with or

On:

Off:

Displayscolorsbasedonthestandardvalues.The Displayscolorswithpriorityonthecolorgradation

colorsoutsidethegamutofthemonitorareclipped.

ratherthanthecoloraccuracy.Theprimarycolors

outsidethegamutofthemonitor(blueinthediagram)

areadjustedtothecolorsmostsimilartothosethat

canbedisplayedbythemonitor.

Colorgamutofmonitor

Colorgamutdefinedbystandard

Colorgamutdisplayedonscreen

Attention

• Thisisaconceptualdiagram,anddoesnotdisplaytheactualcolorgamutofthemonitor.

5. Press

to exit.

Attention

• This function can be set only in the color mode speciﬁed by the color gamut standard.

Chapter2AdjustingScreens

Adjusting Gain

●

The brightness of each color component red, green, and blue is called Gain. You can change the hue of “white”

by adjusting gain.

Setting Range

0 to 100%

Procedure

1. Choose “Color” from the Adjustment menu, and press

2. Choose “Advanced Settings” from “Color”, and press

3. Choose “Gain”, and press

4. Choose the color for adjustment from “Red”, “Green”, and “Blue”, and press

5. Use or for adjustment.

6. Press

to exit.

Attention

• Using this function may make some color gradations unavailable for display.

Note

• The “Temperature” setting invalidates this setting.

• The value of gain changes with that of color temperature.

• When gain is changed, the color temperature is changed to “User”.

Adjusting 6 Colors

The hue and saturation can be adjusted for each of six colors: Magenta, Red, Yellow, Green, Cyan, and Blue.

●

Adjustable Range

-100 to 100

Procedure

1. Choose “Color” from the Adjustment menu, and press

2. Choose “Advanced Settings” from “Color”, and press

3. Choose “6 Colors”, and press

4. Choose the color for adjustment from “Magenta”, “Red”, “Yellow”, “Green”, “Cyan”, and “Blue”, and press

5. Select “Hue” or “Saturation”, and press

6. Use or for adjustment.

7. Press

to exit.

Chapter2AdjustingScreens

2-4. Expanding Signal Output Range

The output range of the signal is extended from 16 - 254 to 0 - 255 for display. When images are displayed in black

and white within the restricted range for purposes such as image creation, use this setting to improve the contrast

of the images.

Procedure

1. Choose “Screen” from the Adjustment menu, and press

2. Choose “Range Extension” from “Screen”, and press

3. Select “On”, “Off”, or “Auto” with or

Attention

• When the DVI signal is input, “Auto” cannot be selected.

4. Press

to exit.

2-5. Selecting Screen Size

The image with the resolution other than the recommended resolution is displayed in full screen automatically.

You can change the screen size by using the “Screen Size” function from “Screen”.

DVI, DisplayPort (PC signal) input

●

Settings

Function

Full

Displaysanimageinfullscreen.Imagesaredistortedinsomecasesbecausethevertical

rateisnotequaltothehorizontalrate.

Enlarged

Normal

Displaysanimageinfullscreen.Insomecases,ablankhorizontalorverticalborder

appearstoequalizetheverticalrateandthehorizontalrate.

Displaysimageswiththespeciﬁedresolution.

Example: Image size 1280 × 1024

Full

Enlarged

Normal

2560×1400

1800×1440

1280×1024

Procedure

1. Choose “Screen” from the Adjustment menu, and press

2. Choose “Screen Size” from “Screen”, and press

3. Select “Full”, “Enlarged”, or “Normal” with or

4. Press

to exit.

Attention

• Selecting “Normal” may make some color gradations unavailable for display.

Chapter2AdjustingScreens

HDMI (HD signal) input

●

Settings

Function

Enlarged

Displaysanimageinfullscreen.Insomecases,ablankhorizontalorverticalborder

appearstoequalizetheverticalrateandthehorizontalrate.

DotbyDot

Displaysimageswiththespeciﬁedresolution.

Example: 720p

Enlarged

DotbyDot

Procedure

1. Choose “Screen” from the Adjustment menu, and press

2. Choose “Screen Size” from “Screen”, and press

3. Select “Enlarged”, or “Dot by Dot” with or

4. Press to exit.

HDMI (SD signal) input

●

Settings

Function

Auto

Themonitorautomaticallychangesthescreensizeaccordingtotheaspectratiosentfrom

theautoinputsignal.

4:3

Displaysimagesina4:3formatscreen.Blackbarsappearonbothsidesofthescreen.

16:9imagesarehorizontallycompressed.

LetterBox

16:9

Displays16:9letterboxedimagesinfullscreen.

Imagesotherthantheletterboxedonesarepartlycutontopandbottom.

Displaystheentire16:9imageinfullscreen.Blackbarsappearonthetopandbottomof

thescreen.

4:3imagesarehorizontallyexpanded.

Example: 480i/480p (16:9)

Auto

4:3

16:9

LetterBox

Procedure

1. Choose “Screen” from the Adjustment menu, and press

2. Choose “Screen Size” from “Screen”, and press

3. Select “Auto”, “4:3”, “Letter Box”, or “16:9” with or

4. Press

to exit.

Chapter2AdjustingScreens

2-6. Conﬁguring Moving Image Performance

This function reduces visible afterimages that appear in fast moving images. If noise or afterimage is adversely

noticeable, set the “Overdrive” setting to “Off”.

Default setting: On

Procedure

1. Choose “Screen” from the Adjustment menu, and press

2. Choose “Overdrive” from “Screen”, and press

3. Select “On” or “Off” with or

4. Press to exit.

2-7. Specifying Color Space

The color space of the input signal can be speciﬁed. Set to other than “Auto” if this product cannot display correct

color.

Settings

Function

Auto

Identiﬁesthecolorspaceoftheinputsignalautomatically.

ConvertsthecolorspaceoftheinputsignaltoaYUV4:2:2format.

ConvertsthecolorspaceoftheinputsignaltoaYUV4:4:4format.

ConvertsthecolorspaceoftheinputsignaltoanRGVformat.

YUV4:2:2

YUV4:4:4

RGB

Procedure

1. Choose “Screen” from the Adjustment menu, and press

2. Choose “Color Space” from “Screen”, and press

3. Select “Auto”, “YUV 4:2:2”, “YUV 4:4:4”, or “RGB” with or

4. Press

to exit.

Attention

• The setting is required when a DVI device is connected to the monitor (at the HDMI connector port) using the DVI-

HDMI conversion connector.

• Even if “Auto” is set, correct color might not be displayed.

Note

• The color space at the DVI input is converted to an RGB format.

Chapter2AdjustingScreens

2-8. Setting HDMI

Reducing Noise

●

The small noises that occur in dark images are reduced. Use this function to reduce noise and roughness in

images.

Procedure

1. Choose “Screen” from the Adjustment menu, and press

2. Choose “HDMI Settings” from “Screen”, and press

3. Choose “Noise Reduction”, and press

4. Select “On” or “Off” with or

5. Press

to exit.

Attention

• Using the Noise Reduction function may deteriorate ﬁne images.

• For interlace signals, the setting value can be changed but this function does not work.

Chapter2AdjustingScreens

Chapter 3 Setting Monitor

3-1. Enabling/Disabling Mode Selection

This function selects / deselects modes that should be skipped. Please use this function if you would like to prevent

a mode from being used.

Procedure

1. Choose “Tools” from the Adjustment menu, and press

2. Choose “Mode Preset” from “Tools”, and press

3. Use or to select the mode to change, and press

4. Select “On” or “Off” with or

5. Press

to exit.

Attention

• You cannot set all the modes disable. Set at least one mode to “On”.

3-2. Selecting the Language

This function allows you to select a language for the Adjustment menu and messages.

Selectable languages

English/German/French/Spanish/Italian/Swedish/Japanese/Simpliﬁed Chinese/Traditional Chinese

Procedure

1. Choose “Menu Settings” from the Adjustment menu, and press

2. Choose “Language” from “Menu Settings”, and press

3. Select a language with or

4. Press to exit.

3-3. Setting Orientation

This function allows you to change the orientation of the Adjustment menu.

Procedure

1. Choose “Menu Settings” from the Adjustment menu, and press

2. Choose “Orientation” from “Menu Settings”, and press

3. Select “Landscape” or “Portrait” with or

4. Press to exit.

5. When selecting “Portrait”, turn the monitor screen 90˚ in clockwise direction.

Attention

• Be sure that the cables are correctly connected.

• Be sure to turn the monitor screen after pulling up the screen to the uppermost position of the stand and setting the

screen tilted upward.

Note

• For using the monitor with “Portrait” position, the graphics board supporting portrait display is required. When placing

the monitor in a “Portrait” position, settings of your graphics board need to be changed. Refer to the User’s Manual of

the graphics board for details.

Chapter3SettingMonitor

3-4. Changing Adjustment Menu Display Position

You can change the display position of the Adjustment menu.

Procedure

1. Choose “Menu Settings” from the Adjustment menu, and press

2. Choose “Menu Position” from “Menu Settings”, and press

3. Choose the position with or

4. Press to exit.

3-5. Showing and Hiding the EIZO Logo

Procedure

1. Press to turn off the monitor.

2. Holding

down, press for at least two seconds to turn on the monitor.

The “Optional Settings” menu appears.

3. Choose “Logo” from “Optional Settings”, and press

4. Select “On” or “Off” with or , and press

5. Select “Finish” with or

6. Press

3-6. Locking Operation Buttons

This function allows you to lock the settings status to prevent changing them.

Procedure

1. Press to turn off the monitor.

2. Holding

down, press for at least two seconds to turn on the monitor.

The “Optional Settings” menu appears.

3. Choose “Key Lock” from “Optional Settings”, and press

4. Choose “Off”, “Menu”, or “All” with or , and press

Settings

Buttons that can be locked

Off

None(Allbuttonsareenabled)

(Defaultsetting)

All

button

Allbuttonsexcluding

5. Select “Finish” with or

6. Press

Chapter3SettingMonitor

3-7. Setting Signal Bandwidth

The range of frequency and detection sensitivity of the change in signal can be switched.

Attention

• The graphics board supporting signal display is required. Refer to the User’s Manual of the graphics board.

• This function cannot be used with HDMI input.

Procedure

1. Press to turn off the monitor.

2. Holding

down, press for at least two seconds to turn on the monitor.

The “Optional Settings” menu appears.

3. Choose “Signal Selection” from “Optional Settings”, and press

4. Choose the input signal to set with or , and press

5. Select “Normal” or “Wide” with or , and press

6. Press

7. Select “Finish” with or

8. Press

twice.

3-8. Switching USB Port Automatically

This function allows the input signal to link the USB upstream port when one monitor is connected to two PCs.

This can switch the USB port automatically according to the switch of the input signal. To calibrate one monitor

using two PCs, the USB cables do not need to be connected again. USB devices such as the mouse and keyboard

connected to one monitor can be used with two PCs.

Attention

• To switch the USB port to be used, two USB cables are required. Prepare cables.

• If a storage device such as a USB memory is connected to the monitor, remove the device before changing the setting.

Otherwise, data may be lost or damaged.

• The key arrangement of the keyboard cannot be changed.

Note

• When the “Input Selection” function is set to “Auto”, the USB port automatically switches according to the switch of the

input signal.

• The USB downstream port can be operated using the currently monitored PC.

Procedure

1. Choose “Tools” from the Adjustment menu, and press

2. Choose “USB Selection” from “Tools”, and press

3. Choose the input signal to set with or , and press

4. Select “USB-1” or “USB-2” with or

5. Press to exit.

Chapter3SettingMonitor

3-9. Changing DUE (Digital Uniformity Equalizer)

Setting

The DUE setting can be changed.

Settings

Function

Brightness

Makesthebrightnessandcolorofthewholescreenuniformwithoutchangingthe

maximumbrightnessandcontrastratio.Thebrightnessofahighgradationareaisnot

corrected.Selectthissettingtoprioritizethelevelsofthebrightnessandcontrastoverthe

uniformityinthehighgradationarea.

Uniformity(Default

setting)

Makesthebrightnessandcolorofthewholescreenuniform.Thebrightnessofahigh

graduationareaisalsocorrectedsoitisuniform.Selectthissettingtoprioritizethe

uniformityoverthelevelsofthebrightnessandcontrastinthehighgradationarea.

Attention

• To change the DUE setting, the adjusted monitor display must be readjusted. Perform the target adjustment again using

ColorNavigator or ColorNavigator Elements. Regarding ColorNavigator and ColorNavigator Elements, see “T o u se

ColorNavigator/ColorNavigator Elements” (page 10).

Procedure

1. Press to turn off the monitor.

2. Holding

down, press for at least two seconds to turn on the monitor.

The “Optional Settings” menu appears.

3. Choose “DUE Priority” from “Optional Settings”, and press

4. Select “Uniformity” or “Brightness” with or , and press

5. Select “Finish” with or

6. Press

Chapter3SettingMonitor

3-10.Reset to default

The setting values are reset to the default settings.

Attention

• After resetting, you cannot undo the operation.

Note

• Regarding the default setting, see “Main Default Settings” (page 47).

To reset the color adjustments

The setting values are reset to the default settings.

●

Procedure

1. Choose “Color” from the Adjustment menu, and press

2. Choose “Color Reset” from “Color”, and press

3. Select “Execute” with or

4. Press

To reset all adjustments to the default settings

This function resets all adjustments to the default settings (except the “Optional Settings” menu and “USB

Selection”).

●

Procedure

1. Choose “Tools” from the Adjustment menu, and press

2. Choose “All Reset” from “Tools”, and press

3. Select “Execute” with or

4. Press

Chapter3SettingMonitor

Chapter 4 SelfCorrection

This product is equipped with a built-in correction sensor. The conditions that have been adjusted using ColorNavigator

and the measurement device, or ColorNavigator Elements can be maintained.

As the adjustment targets or interval times for SelfCorrection are set in advance using ColorNavigator or

ColorNavigator Elements, the built-in correction sensor automatically executes regular display correction.

Attention

• To execute SelfCorrection, it is necessary to set the correction details. Set the target value in advance using ColorNavigator

or ColorNavigator Elements. Regarding ColorNavigator and ColorNavigator Elements, see “T o u se ColorNavigator/

ColorNavigator Elements” (page 10).

Note

• SelfCorrection can also be executed when there are no computer signals being input.

4-1. Executing SelfCorrection

Procedure

1. Choose “SelfCorrection” from the Adjustment menu, and press

2. Choose “Execute” from “SelfCorrection”, and press

The built-in correction sensor is activated, and SelfCorrection is executed.

Attention

• After selecting “Execute”, aging may be executed before the built-in correction sensor is executed.

Chapter4SelfCorrection

Chapter 5 Power Saving Functions

5-1. Setting Power Save

This function allows you to set the monitor into the power saving mode according to the PC status. When the

monitor has shifted to the power saving mode, the images on the screen are not displayed.

Attention

• Turning off the main power switch or unplugging the power cord completely shuts off power supply to the monitor.

• Devices connected to the USB downstream port work when the monitor is in power saving mode or when the power button

of the monitor is Off . Therefore, power consumption of the monitor varies with connected devices even in the power saving

mode.

• Five seconds before the monitor enters the power saving mode, it displays a preliminary message.

Procedure

1. Choose “PowerManager” from the Adjustment menu, and press

2. Choose “Power Save” from “PowerManager”, and press

3. Select “On” or “Off” with or

4. Press to exit.

Power Saving System

DVI Signal Input

This monitor complies with the “DVI DMPM” standard.

DisplayPort Signal Input

This monitor complies with the “DisplayPort Standard V1.1a”.

Monitor

Operatingmode

Powersavingmode

Power Indicator

Blue

Powersavingmode

Orange

HDMI Signal Input

The monitor enters the power saving mode after ﬁve seconds in connection with the PC setting.

Monitor

Operatingmode

Powersavingmode

Power Indicator

Blue

Powersavingmode

Orange

Exiting the power saving mode

If the monitor receives input, it automatically exits the power saving mode and returns to the normal display

mode.

Chapter5PowerSavingFunctions

5-2. Enabling/Disabling Automatic Brightness

Adjustment

The ambient light sensor on the front side of the monitor detects the environmental brightness to adjust the screen

brightness automatically and comfortably by using the Auto EcoView function.

Attention

• Be careful not to block the ambient light sensor on the lower side of the monitor when using the Auto EcoView function.

• Auto EcoView cannot be used when ColorNavigator and/or ColorNavigator Elements is used.

Procedure

1. Choose “PowerManager” from the Adjustment menu, and press

2. Choose “Auto EcoView” from “PowerManager”, and press

3. Select “On” or “Off” with or

4. Press

to exit.

Note

• For this reason, as “Brightness” in the Adjustment menu is changed, the auto adjustment range is also changed.

5-3. Checking the Power Saving Level

The EcoView menu allows you to check Power Reduction, CO₂Reduction, and Eco Performance Level. The more

indicators light up representing the Eco Performance Level, the higher the power saving level attained.

Procedure

1. Choose “PowerManager” from the Adjustment menu, and press

2. Choose “EcoView Index” from “PowerManager”, and press

The “EcoView Index” appears.

5-4. Adjusting the Brightness of Indicator

The brightness of the power indicator (blue) can be adjusted. (Default setting: 4)

Procedure

1. Choose “PowerManager” from the Adjustment menu, and press

2. Choose “Indicator” from “PowerManager”, and press

3. Select the indicator brightness “Off” or in the range from 1 to 7 with or as desired.

4. Press to exit.

Chapter5PowerSavingFunctions

5-5. Setting DisplayPort Power Save

This function allows you to change the power setting of the DisplayPort of the monitor.

Attention

• For the “On” setting, the position of the window may be changed when the signal is switched. In such a case, turn the setting

to “Off”.

Procedure

1. Press to turn off the monitor.

2. Holding

down, press for at least two seconds to turn on the monitor.

The “Optional Settings” menu appears.

3. Choose “DP Power Save” from “Optional Settings”, and press

4. Select “On” or “Off” with or , and press

5. Select “Finish” with or

6. Press

Chapter5PowerSavingFunctions

Chapter 6 Troubleshooting

If a problem still remains after applying the suggested remedies, contact your local EIZO representative.

6-1. No picture

Problem

Possible cause and remedy

1. No picture

• Checkwhetherthepowercordisconnectedproperly.

• Powerindicatordoesnotlight.

• Press

• Turnthemainpowerswitchon.

• Turnoffthemainpower,andthenturnitonagainafew

minuteslater.

• Powerindicatorislightingblue.

• Powerindicatorislightingorange.

• Increase“Brightness”and/or“Gain”intheAdjustment

menu(see“T operformadvancedadjustments”(page18)).

• Switchtheinputsignalwith

• Operatethemouseorkeyboard.

• CheckwhetherthePCisturnedon.

• Powerindicatorﬂashesorangeandblue.

• ThedevicethatisconnectedusingDisplayPort/HDMI

haveaproblem.Solvetheproblem,turnoffthemonitor,

andthenturnitonagain.RefertotheUser’sManualof

theoutputdeviceforfurtherdetails.

2. The message below appears.

Thismessageappearswhenthesignalisnotinputcorrectly

evenwhenthemonitorfunctionsproperly.

• Thismessageappearswhennosignalis

input.

• Themessageshownleftmayappear,becausesomePCs

donotoutputthesignalsoonafterpower-on.

Example:

• CheckwhetherthePCisturnedon.

• Checkwhetherthesignalcableisconnectedproperly.

• Switchtheinputsignalwith

• Themessageshowsthattheinputsignalisout • CheckwhetherthePCisconﬁguredtomeettheresolution

ofthespeciﬁedfrequencyrange.(Suchsignal

frequencyisdisplayedinmagenta.)

Example:

andverticalscanfrequencyrequirementsofthemonitor

(see“2-1.CompatibleResolutions”(page15)).

• RebootthePC.

• Selectanappropriatesettingusingthegraphicsboards

utility.RefertotheUser’sManualofthegraphicsboard

fordetails.

fD: DotClock

fH: HorizontalScanFrequency

fV: Verticalscanfrequency

Chapter6Troubleshooting

6-2. Imaging problems

Problem

Possible cause and remedy

1. The screen is too bright or too dark.

• Use“Brightness”intheAdjustmentmenutoadjustit.(The

LCDmonitorbacklighthasalimitedlifespan.)Whenthe

screenbecomesdarkorbeginstoﬂicker,contactyour

localEIZOrepresentative.)

2. Characters are blurred.

3. Afterimages appear.

• CheckwhetherthePCisconﬁguredtomeettheresolution

andverticalscanfrequencyrequirementsofthemonitor

(see“2-1.CompatibleResolutions”(page15)).

• Use“OutlineEnhancer”intheAdjustmentmenutoadjust

it(see“T oenhanceoutlineofimage”(page21)).

• AfterimagesareparticulartoLCDmonitors.Avoid

displayingthesameimageforalongtime.

• Usethescreensaverorpowersavingfunctiontoavoid

displayingthesameimageforextendedperiodsoftime.

4. Green/red/blue/white dots or defective

dots remain on the screen.

• ThisisduetoLCDpanelcharacteristicsandisnota

failure.

5. Interference patterns or pressure marks

remain on the screen.

• Leavethemonitorwithawhiteorblackscreen.The

symptommaydisappear.

6. Noise appears on the screen.

• IntheAdjustmentmenu,set“Overdrive”to“Off”(see“2-6.

ConﬁguringMovingImagePerformance”(page26)).

• WhenenteringthesignalsofHDCP,thenormalimages

maynotbedisplayedimmediately.

7. (DisplayPort input)

• Whenthesignalisswitched,thepositionofthewindow

maybechanged.IntheAdjustmentmenu,set“DPPower

Save”to“Off”(see“5-5.SettingDisplayPortPowerSave”

(page36)).

Display position of the windows changes.

8. (HDMI input) Displays are abnormal.

• Use“Screen”-"ColorSpace"undertheAdjustmentmenu

toadjustit.

9. An image does not display on the entire

screen.

• Thescreenissettoasizeotherthan“Full”.Changethe

settingto“Full”.

Chapter6Troubleshooting

6-3. Other problems

Problem

Possible cause and remedy

1. The adjustment menu does not appear.

• Checkwhethertheoperationlockfunctionworks(see“3-6.

LockingOperationButtons”(page29)).

2. No mode menu is displayed.

• Checkwhethertheoperationlockfunctionworks(see“3-6.

LockingOperationButtons”(page29)).

3. The monitor connected with the USB cable

is not detected. / USB devices connected

to the monitor does not work.

• CheckwhethertheUSBcableisconnectedcorrectly(see

“7-3.MakingUseofUSB(UniversalSerialBus)”(page44)).

• Checkthe“Tools”–“USBSelection”settingsunder

theSettingmenu(see“3-8.SwitchingUSBPort

Automatically”(page30)).

• ChangetheUSBporttoanotherone.IfthePCor

peripheraldevicesworkscorrectlybychangingtheUSB

port,contactyourlocalEIZOrepresentative.(Refertothe

manualofthePCfordetails.)

• RebootthePC.

• IftheperipheraldevicesworkcorrectlywhenthePCand

peripheraldevicesareconnecteddirectly,pleasecontact

yourlocalEIZOrepresentative.

• CheckwhetherthePCandOSareUSBcompliant.(For

USBcomplianceoftherespectivedevices,consulttheir

manufacturers.)

• CheckthePC’sBIOSsettingforUSBwhenusing

Windows.(RefertothemanualofthePCfordetails.)

4. Audio is not output.

• ThismonitordoesnotsupporttheHDMI/DisplayPort

audiosignals.

Chapter6Troubleshooting

6-4. Built-in correction sensor and SelfCorrection

problems

Problem

Possible cause and remedy

1. The built-in correction sensor does not

come out/stays out.

• Turnoffthemainpower,andthenturnitonagainafew

minuteslater.

• Ifaproblemstillremainsafterapplyingthesuggested

remedies,contactyourlocalEIZOrepresentative.

2. SelfCorrection cannot be executed.

3. SelfCorrection failure

• CheckwhethertheColorNavigatorlicenseiscertiﬁed.

(See“T ouseColorNavigator/ColorNavigatorElements”

(page10).)

• SettheSelfCorrectiontargetusingColorNavigatoror

ColorNavigatorElements.

• Refertotheerrorcodetable.Ifanerrorcodethatdoes

notappearintheerrorcodetableisdisplayed,contact

yourlocalEIZOrepresentative.

Error Code Table

Error Code

Description

0014

• ExecuteSelfCorrectionagain.

• AdjustusingColorNavigatororColorNavigatorElements.

0034

• Thebuilt-incorrectionsensormaynothavecomeoutduringcalibration,orlightmay

haveenteredthesensorduringmeasurement.

• Turnoffthemainpower,waitforafewminutesbeforeturningthepowerbackon,and

thenexecuteSelfCorrectionagain.

0050

0061

• ExecuteSelfCorrectionagain.

• Thebuilt-incorrectionsensormaynothavecomeout.

• Checkwhetherthereisanyforeignobjectnearthebuilt-incorrectionsensor.

• ExecuteSelfCorrectionagain.

Chapter6Troubleshooting

Chapter 7 Reference

7-1. Attaching the Optional Arm

An optional arm (or an optional stand) can be attached by removing the stand section. Please refer to our web site

for the corresponding optional arm (or optional stand). http://www.eizo.com

Attention

• When attaching an arm or stand, follow the instructions of their User’s Manual.

• When using another manufacturer’s arm or stand, conﬁrm the following in advance and select one conforming to the VESA

standard.

- Clearance between the screw holes: 100 mm × 100 mm

- Thickness of plate: 2.6 mm

- Strong enough to support weight of the monitor unit (except the stand) and attachments such as cables.

• When using another manufacturer’s arm or stand, use the following screws to secure it.

- Screws ﬁxing the stand to the monitor.

• When using an arm or stand, attach it to meet the following tilt angles of the monitor.

- Up 45˚, down 45˚

• Connect the cables after attaching an arm or stand.

• Do not move the removed stand up and down. Doing so may result in injury or device damage.

• The monitor and arm or stand are heavy. Dropping them may result in injury or equipment damage.

• When setting the monitor to the portrait style, turn the monitor screen 90˚ in clockwise direction.

Procedure

Lay the LCD monitor on a soft cloth spread over on a stable surface with the

panel surface facing down.

Remove the stand.

Prepare a screwdriver. Loosen the screws (four) securing the unit and the stand with the screwdriver.

Attach the arm or stand to the monitor.

Secure the monitor to the arm or stand using the screws ﬁxing the stand to the monitor.

Chapter7Reference

7-2. Connecting Multiple External Devices

The product has multiple connections to external devices and allows you to switch to one of the connections for

display.

Connection examples

DisplayPort

connector

DVI-Dconnector

HDMIconnector

Digital

(DisplayPort)

Digital

(HDMI)

Digital

(DVI)

Signalcable

(suppliedPM200)

HDMIcable

Signalcable

(suppliedDD200DL)

(Commercially

availableproduct)*¹

HDMIconnector

DVIconnector

MiniDisplayPort

connector

Toexternaldevice1

Toexternaldevice2

Toexternaldevice3

*1 Use a product able to handle High Speed .

Chapter7Reference

To switch among input signals

●

The input signal switches each time

is pressed.

When the signal is switched, the active input port name appears at the top right corner of the screen.

To set input signal selection “Input Selection”

Settings

Function

Auto

Themonitorrecognizestheconnectorthroughwhichsignalsareinput.

Whenanexternaldeviceentersthepowersavingmode,themonitorautomaticallydisplays

anothersignal.

Manual

Themonitordisplaysthesignalfromtheselectedconnectordespitethesignalinput.Select

theinputsignalfordisplayusingthe

operationbutton.

Procedure

1. Choose “Tools” from the Adjustment menu, and press

2. Choose “Input Selection” from “Tools”, and press

3. Select “Auto” or “Manual” with or

4. Press

to exit.

Note

• When “Auto” is selected for “Input Selection”, the monitor’s power saving function works only when all external

devices are in the power saving mode.

Chapter7Reference

7-3. Making Use of USB (Universal Serial Bus)

This monitor has a USB hub. Connected to a PC compatible with USB, this monitor functions as a USB hub

allowing connection to peripheral USB devices.

System Requirement

• A PC equipped with a USB port.

●

• Windows 2000/XP/Vista/7 or Mac OS 9.2.2 and Mac OS X 10.2 or later

• USB cable

Attention

• This monitor may not work depending on PC, OS or peripheral devices. For USB compatibility of peripheral devices,

contact their manufactures.

• Devices connected to the USB upstream port and USB downstream port work when the monitor is in power saving

mode or when the power button of the monitor is Off. Therefore, power consumption of the monitor varies with

connected devices even in the power saving mode.

• When the main power of the monitor is Off, device connected to the USB downstream port does not operate.

Procedure

●

1. Connect the signal cable between a PC and the monitor, and turn on the PC.

2. Using the USB cable, connect the computer’s downstream port and the monitor’s upstream port 1.

3. Connect the peripheral USB device to the USB downstream port of the monitor.

Note

• By default, USB upstream port 1 is enabled. To connect two PCs, see “3-8. Switching USB Port Automatically” (page 30).

USB

downstream

port

USB

upstream

port

Chapter7Reference

7-4. Showing Monitor Information

Displaying signal information “Signal Info”

This function displays the information about the current input signals displayed.

●

Procedure

1. Choose “Tools” from the Adjustment menu, and press

2. Choose “Signal Info” from “Tools”, and press

The “Signal Info” appears.

(Example)

Displaying Monitor Information “Monitor Info”

This function displays the information about the monitor.

Procedure

●

1. Choose “Tools” from the Adjustment menu, and press

2. Choose “Monitor Info” from “Tools”, and press

The “Monitor Info” appears.

This function displays the model name, serial number, ﬁrmware version, usage time, and ColorNavigator license

status.

Attention

• The usage time is not always “0” when you purchase the monitor due to factory inspection.

• If “ColorNavigator License” in the monitor information screen is “Not Registered”, the ColorNavigator license must be

purchased and registered to the monitor. For the purchase of the license, contact your local EIZO representative.

Chapter7Reference

7-5. Speciﬁcations

LCDPanel

Size

27.0inch(680mm)

ColorTFT,IPS

Type

Surfacetreatment

Surfacehardness

Viewingangles

Dotpitch

HardCoating

Horizontal178˚,vertical178˚(CR≥10)

0.233mm

Responsetime

Black-white-black: Approx.12ms

Gray-to-gray:

242MHz

Approx.6ms

Max.dotclock DVI/DisplayPort

HDMI

149MHz

Horizontalscan DVI/DisplayPort

26kHz-89kHz

15kHz-68kHz

frequency

HDMI

Verticalscan

frequency

DVI/DisplayPort

23.75Hz-63Hz(non-interlace)

(VGATEXT:69Hz-71Hz)

HDMI

23.75Hz-61Hz

FrameSynchronousmode

Resolution

23.75Hz-30.5Hz,47.5Hz-61Hz

2560dots×1440lines

Max.displaycolor

Displayarea(H×V)

Powersupply

Approx.1073.74millioncolors(forDisplayPort10bit)

596.7mm(23.5inch)×335.7mm(13.2inch)

100-120VAC±10%,50/60Hz1.55A

200-240VAC±10%,50/60Hz0.8A

Power

ScreendisplayOn

154Worless

consumption

Powersavingmode

0.7Worless (whenonlytheDisplayPortsignalconnectoris

connected,whentheOSentersthesleepmodeor

whenthesettingtoturnoffthemonitorisenabled,

InputSelection:Manual,andnoUSBdeviceis

connected)

PowerOff

0.5Worless (whennoUSBdeviceisconnected)

MainpowerOff

Inputsignalconnectors

DVI-Dconnector(ApplicabletoHDCP)

DisplayPortconnector(StandardV1.1a,applicabletoHDCP)

HDMIconnector(ApplicabletoTypeA,HDCP)

TMDS(SingleLink/DualLink)

Digitalsignal

transmission

system

DVI

HDMI

TMDS(SingleLink)

Plug&Play

DVI/HDMI

DisplayPort

Mainunit

VESADDC2B/EDIDstructure1.3

VESADisplayPort/EDIDstructure1.4

Dimensions

(width)×(height)

×(depth)

646mm(25.4inch)×425mm–576.5mm(16.7inch-22.7inch)×

281mm(11.1inch)

Mainunit(withoutstand) 646mm(25.4inch)×402mm(15.8inch)×92mm(3.62inch)

Mainunit Approx.13.6kg(30lbs.)

Mainunit(withoutstand) Approx.9.7kg(21.4lbs.)

Mass

Movablerange Tilt:

Swivel:

Up:25˚,down:0˚

344˚

Adjustableheight:

Rotation:

190mm(7.5inch)(151.5mm(6.0inch)fortiltof0˚)

90˚(clockwise)

Chapter7Reference

Environmental Temperature

conditions

Operating:

Storage/Transportation: -20˚Cto60˚C(-4˚Fto140˚F)

Operating: 20%to80%R.H.(nocondensation)

Storage/Transportation: 10%to90%R.H.(nocondensation)

Operating: 700hPato1060hPa

0˚Cto35˚C(32˚Fto95˚F)

Humidity

Airpressure

Storage/Transportation: 200hPato1060hPa

USBSpeciﬁcationRevision2.0

USB

Standard

Upstreamport×2,Downstreamport×2

480Mbps(high),12Mbps(full),1.5Mbps(low)

Port

CommunicationSpeed

Supplycurrent

Downstream:

Max.500mA/1port

Main Default Settings

ColorMode

User1

OutlineEnhancer

ScreenSize

Full(DVI,DisplayPort)

Enlarged(HDMI,HD)

Auto(HDMI,SD)

Overdrive

PowerSave

AutoEcoView

Language

English

Center

Manual

MenuPosition

InputSelection

DPPowerSave

DUEPriority

Uniformity

Chapter7Reference

Outside Dimensions

Unit:mm(inch)

616 (24.3)

344°

SWIVEL

646 (25.4)

23.5 (0.93)

599 (23.6)

279 (11.0)

TILT

30°~

273 (10.7)

100 (3.9)

273 (10.7)

PIVOT

31 (1.22)

313 (12.3)

45.5 (1.79)

256.5 (10.1)

255 (10.0)

281.5 (11.1)

Chapter7Reference

Chapter 8 Glossary

Adobe RGB

This is a deﬁnition of the practical RGB color space proposed by Adobe Systems in 1998. The color

reproduction range (color gamut) is broader than sRGB, and is highly adaptable to such ﬁelds as printing etc.

Color Space

YUV and RGB, etc. are available. YUV expresses the color by using the luminance (Y), the color difference

of Blue (U), and the color difference of Red (V). RGB does this by using the gradation of the 3 colors, Red

(R), Green (G), and Blue (B).

DisplayPort

DisplayPort is a next-generation digital AV interface that allows connection of the PC, audio, imaging

devices, etc. to the monitor. One cable can transfer sound with images.

DVI (Digital Visual Interface)

DVI is a digital interface standard. DVI allows direct transmission of the PC’s digital data without loss.

This adopts the TMDS transmission system and DVI connectors. There are two types of DVI connectors.

One is a DVI-D connector for digital signal input only. The other is a DVI-I connector for both digital and

analog signal inputs.

DVI DMPM (DVI Digital Monitor Power Management)

DVI DMPM is a digital interface power saving function. The “Monitor ON (operating mode)” and “Active

Off (power saving mode)” are indispensable for DVI DMPM as the monitor’s power mode.

Gain

This is used to adjust each color parameter for red, green and blue. An LCD monitor displays the color by

the light passing through the panel color ﬁlter. Red, green and blue are the three primary colors. All the

colors on the screen are displayed by combining these three colors. The color tone can be changed by

adjusting the light intensity (volume) passing through each color’s ﬁlter.

Gamma

Generally, the monitor brightness varies nonlinearly with the input signal level, which is called “Gamma

Characteristic”. A small gamma value produces a low-contrast image, while a large gamma value produces a

highcontrast image.

HDCP (High-bandwidth Digital Content Protection)

Digital signal coding system developed to copy-protect the digital contents, such as video, music, etc.

This helps to transmit the digital contents safely by coding the digital contents sent via the DVI or HDMI

connector on the output side and decoding them on the input side.

Any digital contents cannot be reproduced if both of the equipments on the output and input sides are not

applicable to HDCP system.

Chapter8Glossary

HDMI (High-Deﬁnition Multimedia Interface)

HDMI is a digital interface standard, developed for consumer electrical appliance or AV device. This

standard is issued on the basis of the DVI standard which is one of an interface speciﬁcation for the

connection between a PC and a monitor. The projected image, sound and control signal without compressed

enable to be transmitted with one cable.

Overdrive

This technology enhances response speed by increasing the potential difference at the time of motion of

liquid-crystal pixels, and it is used for liquid-crystal TV sets and others in general. It provides clear-cut

three-dimensional display with little afterimage, by improving response speed of the intermediate graduation

range that frequently appears in moving images.

Resolution

The LCD panel consists of numerous pixels of speciﬁed size, which are illuminated to form images. This

monitor consists of horizontal 2560 pixels and 1440 vertical pixels. At a resolution of 2560 × 1440, all pixels

are illuminated as a full screen (1:1).

sRGB (Standard RGB)

International standard for color reproduction and color space among peripheral devices (such as monitors,

printers, digital cameras, scanners). As a form of simple color matching for the Internet, colors can be

displayed using tones close to those of the transmission and reception devices.

Temperature

Color temperature is a method to measure the white color tone, generally indicated in degrees Kelvin. The

screen becomes reddish at a low temperature, and bluish at a high temperature, like the ﬂame temperature.

5000 K: Slightly reddish white

6500 K: White referred to as daylight-balanced color

9300 K: Slightly bluish white

TMDS (Transition Minimized Differential Signaling)

A signal transmission system for digital interface.

Chapter8Glossary

Appendix

Trademark

The terms HDMI and HDMI High-Deﬁnition Multimedia Interface, and the HDMI Logo are trademarks or

registered trademarks of HDMI Licensing, LLC in the United States and other countries.

The DisplayPort Compliance Logo and VESA are registered trademarks of the Video Electronics Standards

Association.

Acrobat, Adobe, Adobe AIR, and Photoshop are registered trademarks of Adobe Systems Incorporated in the

United States and other countries.

AMD Athlon and AMD Opteron are trademarks of Advanced Micro Devices, Inc.

Apple, ColorSync, eMac, iBook, iMac, iPad, Mac, MacBook, Macintosh, Mac OS, PowerBook, and QuickTime

are registered trademarks of Apple Inc.

ColorMunki, Eye-One, and X-Rite are registered trademarks or trademarks of X-Rite Incorporated in the United

States and/or other countries.

ColorVision and ColorVision Spyder2 are registered trademarks of DataColor Holding AG in the United States.

Spyder3 and Spyder4 are trademarks of DataColor Holding AG.

ENERGY STAR is a registered trademark of the United States Environmental Protection Agency in the United

States and other countries.

GRACoL and IDEAlliance are registered trademarks of International Digital Enterprise Alliance.

NEC is a registered trademark of NEC Corporation.

PC-9801 and PC-9821 are trademarks of NEC Corporation.

NextWindow is a registered trademark of NextWindow Ltd.

Pentium is a registered trademark of Intel Corporation in the United States and other countries.

PowerPC is a registered trademark of International Business Machines Corporation.

PlayStation is a registered trademark of Sony Computer Entertainment Inc.

PSP and PS3 are trademarks of Sony Computer Entertainment Inc.

RealPlayer is a registered trademark of RealNetworks, Inc.

TouchWare is a trademark of 3M Touch Systems, Inc.

Windows, Windows Media, Windows Vista, SQL Server, and Xbox 360 are registered trademarks of Microsoft

Corporation in the United States and other countries.

EIZO, the EIZO Logo, ColorEdge, DuraVision, FlexScan, FORIS, RadiCS, RadiForce, RadiNET, Raptor, and

ScreenManager are registered trademarks of EIZO NANAO CORPORATION in Japan and other countries.

ColorNavigator, EcoView NET, EIZO EasyPIX, EIZO ScreenSlicer, i•Sound, Screen Administrator, and UniColor

Pro are trademarks of EIZO NANAO CORPORATION.

All other company and product names are trademarks or registered trademarks of their respective owners.

License

A round gothic bold bit map font designed by Ricoh is used for the characters displayed on this product.

Appendix

FCC Declaration of Conformity

For U.S.A. , Canada, etc. (rated 100-120 Vac) Only

FCC Declaration of Conformity

We, the Responsible Party

EIZONANAOTECHNOLOGIESINC.

5710WarlandDrive,Cypress,CA90630

Phone:(562)431-5011

declare that the product

Tradename:EIZO

Model:ColorEdgeCX270

is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuant

toPart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainst

harmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,uses,andcanradiateradio

frequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmful

interferencetoradiocommunications.However,thereisnoguaranteethatinterferencewillnotoccurin

aparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,

whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencouragedtotrytocorrectthe

interferencebyoneormoreofthefollowingmeasures.

* Reorientorrelocatethereceivingantenna.

* Increasetheseparationbetweentheequipmentandreceiver.

* Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.

* Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

Changesormodi cationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidthe

user’sauthoritytooperatetheequipment.

Note

Usetheattachedspeci edcablebeloworEIZOsignalcablewiththismonitorsoastokeepinterference

withinthelimitsofaClassBdigitaldevice.

- ACCord

- ShieldedSignalCable(Enclosed)

Canadian Notice

ThisClassBdigitalapparatuscomplieswithCanadianICES-003.

CetappareilnumériquedeleclasseBestcomformeàlanormeNMB-003duCanada.

Appendix

Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor

Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum Standardzubehör gehörige

Schwenkarm verwendet wird, muss statt dessen ein geeigneter anderer Schwenkarm installiert werden. Bei der

Auswahl des Schwenkarms sind die nachstehenden Hinweise zu berücksichtigen:

Der Standfuß muß den nachfolgenden Anforderungen entsprechen:

a)Der Standfuß muß eine ausreichende mechanische Stabilität zur Aufnahme des Gewichtes vom Bildschirmgerät

und des speziﬁzierten Zubehörs besitzen. Das Gewicht des Bildschirmgerätes und des Zubehörs sind in der

zugehörenden Bedienungsanleitung angegeben.

b)Die Befestigung des Standfusses muß derart erfolgen, daß die oberste Zeile der Bildschirmanzeige nicht höher

als die Augenhöhe eines Benutzers in sitzender Position ist.

c)Im Fall eines stehenden Benutzers muß die Befestigung des Bildschirmgerätes derart erfolgen, daß die Höhe der

Bildschirmmitte über dem Boden zwischen 135 – 150 cm beträgt.

d)Der Standfuß muß die Möglichkeit zur Neigung des Bildschirmgerätes besitzen (max. vorwärts: 5°, min. nach

hinten ≥ 5°).

e)Der Standfuß muß die Möglichkeit zur Drehung des Bildschirmgerätes besitzen (max. ±180°). Der maximale

Kraftaufwand dafür muß weniger als 100 N betragen.

f) Der Standfuß muß in der Stellung verharren, in die er manuell bewegt wurde.

g)Der Glanzgrad des Standfusses muß weniger als 20 Glanzeinheiten betragen (seidenmatt).

h)Der Standfuß mit Bildschirmgerät muß bei einer Neigung von bis zu 10° aus der normalen aufrechten Position

kippsicher sein.

Hinweis zur Ergonomie :

Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1-ITB2000 mit dem Videosignal, 2560 ×

1440, Digital Eingang und mindestens 60,0 Hz Bildwiederholfrequenz, non interlaced. Weiterhin wird aus

ergonomischen Gründen empfohlen, die Grundfarbe Blau nicht auf dunklem Untergrund zu verwenden (schlechte

Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast.)

„Maschinenlärminformations-Verordnung 3. GPSGV:

Der höchste Schalldruckpegel beträgt 70 dB(A) oder weniger gemäss EN ISO 7779“

Appendix

LIMITED WARRANTY

EIZONANAOCORPORATION(hereinafterreferredtoas“EIZO”)anddistributorsauthorizedbyEIZO(hereinafter

referredtoasthe“Distributors”)warrant,subjecttoandinaccordancewiththetermsofthislimitedwarranty(hereinafter

referredtoasthe“Warranty”),totheoriginalpurchaser(hereinafterreferredtoasthe“Original Purchaser”)who

purchasedtheproductspeci edinthisdocument(hereinafterreferredtoasthe“Product”)fromEIZOorDistributors,

thatEIZOandDistributorsshall,attheirsolediscretion,eitherrepairorreplacetheProductatnochargeiftheOriginal

PurchaserbecomesawarewithintheWarrantyPeriod(de nedbelow)thattheProductmalfunctionsorisdamagedinthe

courseofnormaluseoftheProductinaccordancewiththedescriptionintheinstructionmanualattachedtotheProduct

(hereinafterreferredtoasthe“User’s Manual”).

TheperiodofthisWarrantyislimitedto(i)five(5)yearsfromthedateofpurchaseoftheProduct;or,limitedtothe

expirationof(ii)30,000hoursofitsuseoftheProduct(hereinafterreferredtoasthe“Warranty Period”).EIZOand

DistributorsshallbearnoliabilityorobligationwithregardtotheProductinrelationtotheOriginalPurchaseroranythird

partiesotherthanasprovidedunderthisWarranty.

EIZOandDistributorswillceasetoholdorstoreanypartsoftheProductuponexpirationofseven(7)yearsafterthe

productionofsuchpartsisdiscontinued.Inrepairingthemonitor,EIZOandDistributorswilluserenewalpartswhich

complywithourQCstandards.

TheWarrantyisvalidonlyinthecountriesorterritorieswheretheDistributorsarelocated.TheWarrantydoesnotrestrict

anylegalrightsoftheOriginalPurchaser.

NotwithstandinganyotherprovisionofthisWarranty,EIZOandDistributorsshallhavenoobligationunderthisWarranty

whatsoeverinanyofthecasesassetforthbelow:

(a) AnydefectoftheProductcausedbyfreightdamage,modi cation,alteration,abuse,misuse,accident,incorrect

installation,disaster,faultymaintenanceand/orimproperrepairbythirdpartyotherthanEIZOandDistributors;

(b) AnyincompatibilityoftheProductduetopossibletechnicalinnovationsand/orregulations;

(d) AnydeteriorationofdisplayperformancecausedbythedeteriorationofexpendablepartssuchastheLCDpanel

and/orbacklight,etc.(e.g.changesinbrightness,changesinbrightnessuniformity,changesincolor,changesin

coloruniformity,defectsinpixelsincludingburntpixels,etc.);

(e) AnydefectoftheProductcausedbyexternalequipment;

(f) AnydefectoftheProductonwhichtheoriginalserialnumberhasbeenalteredorremoved;

(g) Anynormaldeteriorationoftheproduct,particularlythatofconsumables,accessories,and/orattachments(e.g.

buttons,rotatingparts,cables,User’sManual,etc.);and

(h) Anydeformation,discoloration,and/orwarpoftheexterioroftheproductincludingthatofthesurfaceoftheLCD

panel.

ToobtainserviceundertheWarranty,theOriginalPurchasermustdelivertheProduct,freightprepaid,initsoriginal

packageorotheradequatepackageaffordinganequaldegreeofprotection,assumingtheriskofdamageand/orloss

intransit,tothelocalDistributor.TheOriginalPurchasermustpresentproofofpurchaseoftheProductandthedateof

suchpurchasewhenrequestingservicesundertheWarranty.

TheWarrantyPeriodforanyreplacedand/orrepairedproductunderthisWarrantyshallexpireattheendoftheoriginal

WarrantyPeriod.

EIZOORDISTRIBUTORSARENOTRESPONSIBLEFORANYDAMAGETO,ORLOSSOF,DATAOROTHER

INFORMATIONSTOREDINANYMEDIAORANYPARTOFANYPRODUCTRETURNEDTOEIZOORDISTRIBUTORS

FORREPAIR.

EIZOANDDISTRIBUTORSMAKENOFURTHERWARRANTIES,EXPRESSEDORIMPLIED,WITHRESPECTTO

THEPRODUCTANDITSQUALITY,PERFORMANCE,MERCHANTABILITYORFITNESSFORANYPARTICULAR

USE.INNOEVENTSHALLEIZOORDISTRIBUTORSBELIABLEFORANYINCIDENTAL,INDIRECT,SPECIAL,

CONSEQUENTIALOROTHERDAMAGEWHATSOEVER(INCLUDING,WITHOUTLIMITATION,DAMAGESFOR

LOSSOFPROFIT,BUSINESSINTERRUPTION,LOSSOFBUSINESSINFORMATION,ORANYOTHERPECUNIARY

LOSS)ARISINGOUTOFTHEUSEORINABILITYTOUSETHEPRODUCTORINANYCONNECTIONWITHTHE

PRODUCT,WHETHERBASEDONCONTRACT,TORT,NEGLIGENCE,STRICTLIABILITYOROTHERWISE,EVEN

IFEIZOORDISTRIBUTORSHAVEBEENADVISEDOFTHEPOSSIBILITYOFSUCHDAMAGES.THISEXCLUSION

ALSOINCLUDESANYLIABILITYWHICHMAYARISEOUTOFTHIRDPARTYCLAIMSAGAINSTTHEORIGINAL

PURCHASER.THEESSENCEOFTHISPROVISIONISTOLIMITTHEPOTENTIALLIABILITYOFEIZOAND

DISTRIBUTORSARISINGOUTOFTHISLIMITEDWARRANTYAND/ORSALES.

Appendix

BEGRENZTE GARANTIE

EIZONANAOCORPORATION(imWeiterenals„EIZO“bezeichnet)unddieVertragsimporteurevonEIZO(imWeiteren

als„Vertrieb(e)“bezeichnet)garantierendemursprünglichenKäufer(imWeiterenals„Erstkäufer“bezeichnet),der

dasindiesemDokumentvorgegebeneProdukt(imWeiterenals„Produkt“bezeichnet)vonEIZOodereinemVertrieb

erworbenhat,gemäßdenBedingungendieserbeschränktenGarantie(imWeiterenals„Garantie“bezeichnet),dass

EIZOundderVertriebnacheigenemErmessendasProduktentwederkostenlosreparierenoderaustauschen,falls

derErstkäuferinnerhalbderGarantiefrist(weiteruntenfestgelegt)eineFehlfunktionbzw.BeschädigungdesProdukts

feststellt,diewährenddesnormalenGebrauchsdesProduktsgemäßdenAnweisungendeszumLieferumfangdes

ProduktsgehörendenBenutzerhandbuchs(imWeiterenals„Benutzerhandbuch“bezeichnet)aufgetretenist.

DieDauerderGarantieleistungbeträgt(i)fünf(5)JahreabdemErstverkaufsdatumdesProduktsoder(ii)30.000

BetriebsstundendesProdukts(imWeiterenals„Garantiefrist“bezeichnet).EIZOunddieVertriebeübernehmenüber

denRahmendieserGarantiehinaushinsichtlichdesProduktskeinerleiHaftungoderVerpflichtungdemErstkäufer

oderDrittengegenüber.EIZOunddieVertriebeverpflichtensich,ErsatzteilefürdasProduktübereinenZeitraum

vonsieben(7)JahrennachEinstellungderProduktionderErsatzteilezulagernbzw.anzubieten.EIZOundseine

Vertriebspartnerverp ichtensich,beieineretwaigenReparaturdesMonitorsausschließlichProduktegemäßdenEIZO-

Qualitätssicherungsstandardszuverwenden.

Diese Garantie gilt nur in Ländern oder Gebieten, in denen sich Vertriebe befinden. Die gesetzlichen

GewährleistungsrechtedesErstkäufersgegenüberdemVerkäuferwerdendurchdieseGarantienichtberührt.

EIZOunddieVertriebebesitzenimRahmendieserGarantiekeinerleiVerp ichtungindenfolgendenFällen:

(a) Produktdefekte,dieaufFrachtschäden,Modifikation,Nachgestaltung,Missbrauch,Fehlbedienung,Unfälle,

unsachgemäßeInstallation,Naturkatastrophen,fehlerhafteWartungund/oderunsachgemäßeReparaturdurcheine

andereParteialsEIZOunddieVertriebezurückzuführensind.

(b) EineInkompatibilitätdesProduktsaufgrundvontechnischenNeuerungenund/oderneuenBestimmungen,die

nachdemKaufinKrafttreten.

(d) JeglicheVerschlechterungderBildschirmleistung,diedurchVerschleißteilewiedasLCD-Panelund/oderdie

Hintergrundbeleuchtungusw.hervorgerufenwerden(z.B.VeränderungenvonHelligkeitoderHelligkeitsverteilung,

VeränderungenvonFarbeoderFarbverteilung,PixeldefekteeinschließlichvondurchgebranntenPixelnusw.).

(e) Produktdefekte,diedurchexterneGeräteverursachtwerden.

(f) JeglicherDefekteinesProdukts,dessenursprünglicheSeriennummergeändertoderentferntwurde.

(g) NormaleAbnutzungdesProdukts,insbesonderevonVerbrauchsteilen,Zubehörteilenund/oderBeilagen(z.B.

Tasten,drehbareTeile,Kabel,Benutzerhandbuchusw.);sowie

(h) Verformungen,Verfärbungenund/oderVerziehungenamProduktäußeren,einschließlichderOber ächedesLCD-

Panels.

BeiInanspruchnahmederGarantieleistungistderErstkäuferverpflichtet,dasProduktaufeigeneKostenund

inderOriginalverpackungbzw.eineranderengeeignetenVerpackung,dieeinengleichwertigenSchutzgegen

Transportschädenbietet,andenörtlichenVertriebzuübersenden,wobeiderErstkäuferdasTransportrisikogegenüber

Schädenund/oderVerlustträgt.ZumZeitpunktderInanspruchnahmederGarantieleistungmussderErstkäufereinen

Verkaufsbelegvorweisen,aufdemdasKaufdatumangegebenist.

DieGarantiefristfüreinimRahmendieserGarantieausgetauschtesund/oderrepariertesProdukterlischtnachAblauf

derursprünglichenGarantiefrist.

EIZOODERDIEEIZO-VERTRAGSIMPORTEUREHAFTENNICHTFÜRZERSTÖRTEDATENBESTÄNDEODERDIE

KOSTENDERWIEDERBESCHAFFUNGDIESERDATENBESTÄNDEAUFJEGLICHENDATENTRÄGERNODER

TEILENDESPRODUKTS,DIEIMRAHMENDERGARANTIEBEIEIZOODERDENEIZO-VERTRAGSIMPORTEUREN

ZURREPARATUREINGEREICHTWURDEN.

EIZOUNDDIEEIZO-VERTRAGSIMPORTEUREGEBENWEDEREXPLIZITENOCHIMPLIZITEGARANTIEN

INBEZUGAUFDIESESPRODUKTUNDSEINEQUALITÄT,LEISTUNG,VERKÄUFLICHKEITODEREIGNUNG

FÜREINENBESTIMMTENZWECK.AUFKEINENFALLSINDEIZOODERDIEEIZO-VERTRAGSIMPORTEURE

VERANTWORTLICHFÜRJEGLICHEZUFÄLLIGE,INDIREKTE,SPEZIELLE,FOLGE-ODERANDERESCHÄDEN

JEGLICHERART(EINSCHLIESSLICHOHNEJEDEBEGRENZUNGSCHÄDENBEZÜGLICHPROFITVERLUST,

GESCHÄFTSUNTERBRECHUNG,VERLUSTVONGESCHÄFTSINFORMATIONODERJEGLICHEANDEREN

FINANZIELLENEINBUSSEN),DIEDURCHDIEVERWENDUNGDESPRODUKTESODERDIEUNFÄHIGKEIT

ZURVERWENDUNGDESPRODUKTESODERINJEGLICHERBEZIEHUNGMITDEMPRODUKT,SEIES

BASIERENDAUFVERTRAG,SCHADENSERSATZ,NACHLAESSIGKEIT,STRIKTEHAFTPFLICHTODERANDEREN

FORDERUNGENENTSTEHEN,AUCHWENNEIZOUNDDIEEIZO-VERTRAGSIMPORTEUREIMVORAUSÜBER

DIEMÖGLICHKEITSOLCHERSCHÄDENINFORMIERTWURDEN.DIESERAUSSCHLUSSENTHÄLTAUCHJEDE

HAFTPFLICHT,DIEAUSFORDERUNGENDRITTERGEGENDENERSTKÄUFERENTSTEHENKANN.ZWECK

DIESERKLAUSELISTES,DIEHAFTUNGVONEIZOUNDDENVERTRIEBENGEGENÜBERFORDERUNGENZU

BEGRENZEN,DIEAUSDIESERBESCHRÄNKTENGARANTIEUND/ODERDEMVERKAUFENTSTEHENKÖNNEN.

Appendix

GARANTIE LIMITÉE

EIZONANAOCORPORATION(ci-aprèsdénommé«EIZO »)etlesdistributeursautorisésparEIZO(ci-après

dénommés«Distributeurs »),sousréserveetconformémentauxtermesdecettegarantielimitée(ci-aprèsdénommée

«Garantie »),garantissentàl’acheteurinitial(ci-aprèsdénommé«Acheteur initial »)duproduitspécifiédansla

présente(ci-aprèsdénommé«Produit »)achetéauprèsd’EIZOoudeDistributeursagréésEIZO,queEIZOetses

DistributeursaurontpouroptionderéparerouremplacergratuitementleProduitsil’Acheteurinitialconstate,pendantla

Périodedegarantie(dé nieci-dessous),qu’ilyaundysfonctionnementouqueleProduitasubiundommagedansle

cadred’uneutilisationnormaleduProduitconformémentàladescriptiondumoded’emploiquiaccompagneleProduit

(ci-aprèsdénommé«Manuel d’utilisation »).

LapériodedecetteGarantieestlimitéeà(i)cinq(5)ansàpartirdeladated’achatduProduit;ou,limitéejusqu’à

l’expirationde(ii)30000heuresd’utilisationduProduit(ci-aprèsdénommée«Période de Garantie»).EIZOetses

DistributeursdéclinenttouteresponsabilitéouobligationconcernantceProduitfaceàl’Acheteurinitialouàtouteautre

personneàl’exceptiondecellesstipuléesdanslaprésenteGarantie.

EIZOetsesDistributeurscesserontdetenirouconserverenstocktoutepiècedeceProduitaprèsl’expirationde

lapériodedesept(7)anssuivantl’arrêtdelaproductiondetellespièces.Pourréparerlemoniteur,EIZOetses

distributeursutiliserontdespiècesderechangeconformesànosnormesdecontrôlequalité.

LaGarantieestvalableuniquementdanslespaysoulesterritoiresoùsetrouventlesDistributeurs.LaGarantienelimite

aucundesdroitsreconnusparlaloiàl’Acheteurinitial.

NonobstanttouteautreclausedecetteGarantie,EIZOetsesDistributeursn’aurontd’obligationdanslecadredecette

Garantiepouraucundescasénumérésci-dessous:

(a) ToutdéfautduProduitrésultantdedommagesoccasionnéslorsdutransport,d’unemodi cation,d’unealtération,

d’unabus,d’unemauvaiseutilisation,d’unaccident,d’uneinstallationincorrecte,d’undésastre,d’unentretienet/

oud’uneréparationincorrectseffectuésparunepersonneautrequeEIZOousesDistributeurs;

(b) TouteincompatibilitéduProduitrésultantd’améliorationstechniqueset/ouréglementationspossibles;

(d) Toutedétériorationdesperformancesd’affichagecauséeparladétériorationdesélémentsconsommablestels

quelepanneauLCDet/oulerétroéclairage,etc.(parexempledeschangementsdeluminosité,deschangements

del’uniformitédelaluminosité,desmodi cationsdecouleur,deschangementsdel’uniformitédescouleurs,des

défectuositésdepixelsycomprisdespixelsbrûlés,etc.);

(e) ToutdéfautduProduitcauséparunappareilexterne;

(f) Toutdéfautd’unProduitsurlequellenumérodesérieoriginalaétéaltéréousupprimé;

(g) ToutedétériorationnormaleduProduit,particulièrementcelledesconsommables,desaccessoireset/oudes

piècesreliéesauProduit(touches,élémentspivotants,câbles,Manueld’utilisationetc.),et

(h) Toutedéformation,décoloration,et/ougondolagedel’extérieurduProduit,ycompriscelledelasurfacedu

panneauLCD.

Pourbéné cierd’unservicedanslecadredecetteGarantie,l’AcheteurinitialdoitrenvoyerleProduitportpayé,dans

sonemballaged’origineoutoutautreemballageappropriéoffrantundegrédeprotectionéquivalent,auDistributeurlocal,

etassumeralaresponsabilitédesdommageset/oupertepossibleslorsdutransport.L’Acheteurinitialdoitprésenterune

preuved’achatduProduitcomprenantsadated’achatpourbéné cierdeceservicedanslecadredelaGarantie.

LaPériodedegarantiepourtoutProduitremplacéet/ouréparédanslecadredecetteGarantieexpireraàla ndela

Périodedegarantieinitiale.

EIZOOUSESDISTRIBUTEURSNESAURAIENTÊTRETENUSRESPONSABLESDESDOMMAGESOUPERTESDE

DONNÉESOUD’AUTRESINFORMATIONSSTOCKÉESDANSUNMÉDIAQUELCONQUEOUUNEAUTREPARTIE

DUPRODUITRENVOYÉÀEIZOOUAUXDISTRIBUTEURSPOURRÉPARATION.

AUCUNEAUTREGARANTIE,EXPLICITEOUTACITE,N’ESTOFFERTEPAREIZOETSESDISTRIBUTEURS

CONCERNANTLEPRODUITETSESQUALITÉS,PERFORMANCES,QUALITÉMARCHANDEOUADAPTATION

ÀUNUSAGEPARTICULIER.ENAUCUNCAS,EIZOOUSESDISTRIBUTEURSNESERONTRESPONSABLES

DESDOMMAGESFORTUITS,INDIRECTS,SPÉCIAUX,INDUITS,OUDETOUTAUTREDOMMAGEQUEL

QU’ILSOIT(YCOMPRIS,SANSLIMITATION,LESDOMMAGESRÉSULTANTD’UNEPERTEDEPROFIT,D’UNE

INTERRUPTIOND’ACTIVITÉS,D’UNEPERTEDEDONNÉESCOMMERCIALES,OUDETOUTAUTREMANQUE

ÀGAGNER)RÉSULTANTDEL’UTILISATIONOUDEL’INCAPACITÉD’UTILISERLEPRODUITOUAYANTUN

RAPPORTQUELCONQUEAVECLEPRODUIT,QUECESOITSURLABASED’UNCONTRAT,D’UNTORT,D’UNE

NÉGLIGENCE,D’UNERESPONSABILITÉSTRICTEOUAUTRE,MÊMESIEIZOOUSESDISTRIBUTEURSONTÉTÉ

AVERTISDELAPOSSIBILITÉDETELSDOMMAGES.CETTELIMITATIONINCLUTAUSSITOUTERESPONSABILITÉ

QUIPOURRAITÊTRESOULEVÉELORSDESRÉCLAMATIONSD’UNTIERSCONTREL’ACHETEURINITIAL.

L’ESSENCEDECETTECLAUSEESTDELIMITERLARESPONSABILITÉPOTENTIELLEDEEIZOETDESES

DISTRIBUTEURSRÉSULTANTDECETTEGARANTIELIMITÉEET/OUDESVENTES.

Appendix

GARANTÍA LIMITADA

EIZONANAOCORPORATION(enlosucesivo“EIZO”)ysusdistribuidoresautorizados(enlosucesivolos

“Distribuidores”),conarregloydeconformidadconlostérminosdeestagarantíalimitada(enlosucesivola“Garantía”),

garantizanalcompradororiginal(enlosucesivoel“Comprador original”)quecompróelproductoespeci cadoeneste

documento(enlosucesivoel“Producto”)aEIZOoasusDistribuidores,queEIZOysusDistribuidores,asupropio

criterio,repararánosustituiránelProductodeformagratuitasielCompradororiginaldetectadentrodelperiododela

Garantía(indicadoposteriormente)queelProductonofuncionacorrectamenteoquesehaaveriadoduranteeluso

normaldelmismodeacuerdoconlasindicacionesdelmanualdeinstruccionessuministradoconelProducto(enlo

sucesivoel“Manual del usuario”).

ElperíododevalidezdeestaGarantíaestálimitadoa(i)cinco(5)añosapartirdelafechadecompradelProductoo(ii)

a30.000horasdeusodelProducto(enadelantedesignadocomoel“Periodo de Garantía”).EIZOysusDistribuidores

notendránningunaresponsabilidadniobligaciónconrespectoalProductoparaconelCompradororiginalniparacon

tercerosquenoseanlasestipuladasenlapresenteGarantía.

EIZOysusDistribuidoresnoestaránobligadosasuministrarcualquierrecambiodelProductounavezpasadossiete

(7)añosdesdequesedejedefabricarelmismo.Paralareparacióndelmonitor,EIZOylosdistribuidoresutilizarán

repuestosquecumplanconnuestrosestándaresdecontroldecalidad.

LaGarantíaesválidasóloenlospaísesyterritoriosdondeestánubicadoslosDistribuidores.LaGarantíanorestringe

ningúnderecholegaldelCompradororiginal.

ApesardelasestipulacionesdeestaGarantía,EIZOysusDistribuidoresnotendránobligaciónalgunabajoesta

Garantíaenningunodeloscasosexpuestosacontinuación:

(a) CualquierdefectodelProductocausadopordañoseneltransporte,modi cación,alteración,abuso,usoincorrecto,

accidente,instalaciónincorrecta,desastre,mantenimientoincorrectoy/oreparaciónindebidarealizadaporun

terceroquenoseaEIZOosusDistribuidores.

(b) CualquierincompatibilidaddelProductodebidaaposiblesinnovacionestécnicasy/oreglamentaciones.

(d) Cualquierdeterioroenelrendimientodelavisualizacióncausadoporfallosenlaspiezasconsumiblescomoel

panelLCDy/ola"Backlight",etc.(p.ej.cambiosdebrillo,cambiosdeuniformidaddelbrillo,cambiosdecolor,

cambiosdeuniformidaddelcolor,defectosdepíxeles,incluyendopíxelesmuertos,etc.).

(e) CualquierdefectodelProductocausadoporunequipoexterno.

(f) CualquierdefectodelProductoenelquehayasidoalteradooborradoelnúmerodeserieoriginal.

(g) CualquierdeterioronormaldelProducto,yenparticulardelaspiezasconsumibles,accesoriosydemás(p.ej.

botones,piezasgiratorias,cables,Manualdelusuario,etc.).

(h) Cualquierdeformación,decoloracióny/oalabeodelexteriordelProductoincluidalasuper ciedelpanelLCD.

ParaobtenerservicioenlostérminosdeestaGarantía,elProductodeberáserenviadoporelCompradororiginal,

asuDistribuidorlocal,coneltransportepreviamentepagado,enelembalajeoriginaluotroembalajeadecuadoque

ofrezcaelmismogradodeprotección,asumiendoelriesgodedañosy/opérdidadelProductoduranteeltransporte.El

CompradororiginaldeberápresentaruncomprobantedecompradelProductoenelquesere ejelafechadecompra

delmismocuandolosoliciteelserviciodeGarantía.

ElPeriododegarantíaparacualquierProductoreemplazadoy/oreparadoenlostérminosdeestaGarantíaexpiraráal

vencerelPeriododegarantíaoriginal.

EIZOOLOSDISTRIBUIDORESAUTORIZADOSDEEIZONOSERESPONSABILIZANDENINGÚNDAÑOO

PÉRDIDAQUEPUEDANSUFRIRLOSDATOSUOTRAINFORMACIÓNALMACENADAENCUALQUIERMEDIOO

CUALQUIERPARTEDECUALQUIERPRODUCTODEVUELTOAEIZOOALOSDISTRIBUIDORESDEEIZOPARA

SUREPARACIÓN.

EIZOYLOSDISTRIBUIDORESAUTORIZADOSDEEIZONOOFRECENNINGUNAOTRAGARANTÍA,IMPLÍCITA

NIEXPLÍCITA,CONRESPECTOALPRODUCTOYASUCALIDAD,RENDIMIENTO,COMERCIABILIDADE

IDONEIDADPARACUALQUIERUSOENPARTICULAR.ENNINGÚNCASOSERÁNEIZOOLOSDISTRIBUIDORES

AUTORIZADOSDEEIZORESPONSABLESDENINGÚNDAÑOEMERGENTE,INDIRECTO,ESPECIAL,INHERENTE

OCUALQUIERAQUESEA(INCLUYENDO,SINLIMITACIÓN,DAÑOSPORLUCROCESANTE,INTERRUPCIÓN

DELAACTIVIDADCOMERCIAL,PÉRDIDADEINFORMACIÓNCOMERCIALOCUALQUIEROTRAPÉRDIDA

PECUNIARIA)QUESEDERIVEDELUSOOIMPOSIBILIDADDEUSODELPRODUCTOOENRELACIÓNCONEL

PRODUCTO,YASEABASADOENCONTRATO,PORAGRAVIO,NEGLIGENCIA,ESTRICTARESPONSABILIDAD

OCUALQUIERAQUESEA,AUNCUANDOSEHAYAADVERTIDOAEIZOOALOSDISTRIBUIDORESDEEIZO

DELAPOSIBILIDADDETALESDAÑOS.ESTAEXCLUSIÓNTAMBIÉNABARCACUALQUIERRESPONSABILIDAD

QUEPUEDADERIVARSEDERECLAMACIONESHECHASPORUNTERCEROCONTRAELCOMPRADOR

ORIGINAL.LAESENCIADEESTAESTIPULACIÓNESLIMITARLARESPONSABILIDADPOTENCIALDEEIZOYLOS

DISTRIBUIDORESQUEPUDIERADERIVARSEDEESTAGARANTÍALIMITADAY/OVENTAS.

Appendix

GARANZIA LIMITATA

EIZONANAOCORPORATION(acuisifaràriferimentodaquiinpoicon“EIZO”)ediDistributoriautorizzatidaEIZO(a

cuisifaràriferimentodaquiinpoicon“Distributori”)garantiscono,secondoiterminidiquestagaranzialimitata(acuisi

faràriferimentodaquiinpoicon“Garanzia”)all’acquirenteoriginale(acuisifaràriferimentodaquiinpoicon“Acquirente

originale”)chehaacquistatoilprodottospecificatoinquestodocumento(acuisifaràriferimentodaquiinpoicon

“Prodotto”)daEIZOodaisuoiDistributori,cheEIZOeidistributori,alorodiscrezione,riparerannoosostituirannoil

Prodottosenzaaddebitosel’Acquirenteoriginaletrova,entroilperiododellaGaranzia(de nitosotto),cheilProdotto

malfunzionaesièdanneggiatonelcorsodelsuonormaleutilizzoosservandoleindicazionidelmanualediistruzioni

allegatoalProdotto(acuisifaràriferimentodaquiinpoicon“Manuale utente”).

LapresenteGaranziaèlimitataa(i)cinque(5)anniapartiredalladatad'acquistodelProdottoo(ii)alloscaderedi

30.000ored'utilizzodelProdotto(acuisifaràriferimentodaquiinpoicon“Periodo di Garanzia”).EIZOeisuoi

DistributorinonsiassumonoalcunaresponsabilitàenonhannoalcunobbligoriguardoalProdottoversol'Acquirente

originaleoterzidiversidaquellirelativiaquestaGaranzia.

EIZOeisuoiDistributoricesserannoditenereodiconservarequalsiasiricambiodelProdottoalloscaderedisette

(7)annidopochelaproduzioneditaliricambièstataterminata.Perlariparazionedelmonitor,EIZOeiDistributori

utilizzerannopartidiricambioconformiainostristandarddicontrollodellaqualità.

LaGaranziaèvalidasoltantoneipaesidovecisonoiDistributoriEIZO.LaGaranzianonlimitaalcundirittolegale

dell’Acquirenteoriginale.

IndipendentementedaqualsiasialtracondizionediquestaGaranzia,EIZOeisuoiDistributorinonavrannoalcunobbligo

derivantedaquestaGaranziainognunodeicasielencatidiseguito:

(a) QualsiasidifettodelProdottocausatodadanniditrasporto,modi che,alterazioni,abusi,usiimpropri,incidenti,

installazioneerrata,calamità,manutenzioneerratae/oriparazioniimproprieeseguitedaterzepartichenonsiano

EIZOoisuoiDistributori.

(b) QualsiasiincompatibilitàdelProdottodovutaapossibiliinnovazionitecnichee/onormative.

(d) Qualsiasideterioramentodelleprestazionidelloschermocausatodaldeterioramentodelleparticonsumabili,come

ilpannelloLCDe/olaretroilluminazione,ecc.(peresempio:icambiamentidiluminosità,cambiamentidiuniformità

dellaluminosità,icambiamentidicolore,icambiamentidiuniformitàdelcolore,idifettideipixel,inclusiipixel

bruciati,ecc.).

(e) QualsiasidifettodelProdottocausatodaapparecchiatureesterne.

(f) QualsiasidifettodelProdottoincuiilnumerodiserieoriginalesiastatoalteratoorimosso.

(g) QualsiasinormaledeterioramentodelProdotto,inparticolarmodonellesuepartidiconsumo,accessori,e/o

attacchi(peresempio:tasti,partirotanti,cavi,Manualedell’utente,ecc.).

(h) Qualsiasitipodideformazione,scolorimento,e/odiinvolucroesternodelProdottoinclusalasuper ciedelpannello

LCD.

PerricevereassistenzatecnicaconquestaGaranzia,l’AcquirenteoriginaledeveinviareilProdotto,contrasporto

pre-pagato,nellasuaconfezioneoriginaleoaltraconfezioneadeguatachefornisceunlivelloanalogodiprotezione,

assumendosiilrischiodidannie/operditaintransito,alDistributorelocale.L’Acquirenteoriginaledevepresentarela

provadiacquistochestabilisceladatadiacquistodelProdottoquandorichiedeserviziosottoGaranzia.

IlPeriododigaranziaperqualsiasiProdottosostituitoe/oriparatosottoquestaGaranziascadealla nedelPeriododi

garanziaoriginale.

EIZOOISUOIDISTRIBUTORINONSONORESPONSABILIPERQUALSIASIDANNOOPERDITADIDATIOALTRE

INFORMAZIONIMEMORIZZATISUQUALSIASISUPPORTOOQUALSIASIPARTEDIQUALSIASIPRODOTTO

INVIATOAEIZOOISUOIDISTRIBUTORIPERRIPARAZIONI.

EIZOEISUOIDISTRIBUTORINONOFFRONOALCUNAGARANZIAADDIZIONALE,IMPLICITAOESPLICITA,

RIGUARDOILPRODOTTOELASUAQUALITÀ,PRESTAZIONI,VENDIBILITÀOAPPROPRIATEZZAPER

QUALSIASIUSOPARTICOLARE.INNESSUNCASOEIZOOIDISTRIBUTORIEIZOAUTORIZZATISARANNO

RESPONSABILIPERQUALSIASIDANNOACCIDENTALE,INDIRETTO,SPECIALE,CONSEGUENTEODI

QUALSIASIALTRANATURA(INCLUSI,SENZALIMITI,DANNIPERPERDITADIPROFITTI,INTERRUZIONEDELLE

ATTIVITÀ,PERDITADIINFORMAZIONID’AFFARIOQUALSIASIALTRAPERDITAPECUNIARIA)DERIVANTI

DALL’USOODALL’IMPOSSIBILITÀDIUSAREILPRODOTTOOINQUALSIASIRELAZIONEALPRODOTTO,

SIASUBASEDICONTRATTO,TORTO,NEGLIGENZA,STRETTARESPONSABILITÀOALTRIMENTI,ANCHE

SEEIZOOIDISTRIBUTORIEIZOAUTORIZZATISONOSTATIAVVERTITIDELLAPOSSIBILITÀDITALIDANNI.

QUESTAESCLUSIONEINCLUDEANCHEQUALSIASIRESPONSABILITÀCHEPOSSAINSORGEREDARECLAMI

DITERZICONTROL’ACQUIRENTEORIGINALE.L’ESSENZADIQUESTOPROVVEDIMENTOÈLIMITARELA

RESPONSABILITÀPOTENZIALEDIEIZOEDEIDISTRIBUTORIDERIVANTEDAQUESTAGARANZIALIMITATAE/O

DALLEVENDITE.

Appendix

BEGRÄNSAD GARANTI

EIZONANAOCORPORATION(nedankallat“EIZO”)ochEIZOsauktoriseradedistributörer(nedankallade

“Distributörer”)garanterarienlighetmedvillkorenidennabegränsadegaranti(nedankallad“Garantin”)den

ursprungligeköparen(nedankalladden“Ursprunglige köparen”)somköptedenidokumentetspeci ceradeprodukten

(nedankallad“Produkten”)frånEIZOellerDistributörer,attEIZOellerDistributörerenligtegetgott nnandekostnadsfritt

antingenrepareraellerbytautdendefektaProduktenomdenUrsprungligeköpareninomGarantiperioden(de nieras

nedan)upptäckerattProduktenfungerarfelaktigtellerskadasundernormalanvändningavProduktenienlighetmed

beskrivningenibruksanvisningen(nedankallad“Bruksanvisning”).

Giltighetsperiodenfördennagarantiärbegränsadtill(i)fem(5)årfråndatumetförProduktensinköpeller,omdetta

inträffartidigare,begränsattillutlöpandetav(ii)30000timmarsanvändningavProdukten(härikallad“Garantiperioden”).

EIZOochDistributörerskainteundernågravillkorhanågotannatansvaränvadsomangesidennagarantigällande

ProduktenirelationtilldenUrsprungligeköparenellertredjepart.

EIZOochDistributörerkommerattupphöramedlagerhållningavProduktensdelareftersju(7)årefterattproduktionen

avdessadelarupphört.NätskärmenreparerasanvänderEIZOochdistributörerreservdelarsomuppfyllervåra

kvalitetsstandarder.

GarantinärendastgiltigideländerdärdetfinnsDistributörer.GarantinbegränsarintenågraavdenUrsprunglige

köparenslagstadgaderättigheter.

OavsettandravillkoridennagarantiskainteEIZODistributörerundernågravillkorhanågotansvarinågotavdefall

sombeskrivsnedan:

(a) NärnågonbristfällighethosProduktenkanhärledastillatthauppståttvidfrakt,modifiering,ändring,felaktigt

handhavande,olycka,felaktiginstallation,katastrof,felaktigtunderhålloch/ellerfelaktigreparationutfördavtredje

partannanänEIZOochDistributörer.

(b) AllaformeravinkompatibilitethosProduktenpågrundavmöjligatekniskainnovationeroch/ellerbestämmelser.

(d) Alla försämringar av bildens prestanda beroende på förbrukningsdelar så som LCD-panel och/eller

bakgrundsbelysningetc.(t.ex.ändringariljusstyrka,jämnhetiljusstyrka,färg,färgjämnhet,defektapixlaroch/eller

fastlysandepixlaretc.).

(e) AlladefekterhosProduktensomorsakatsavexternutrustning.

(f) AlladefekterhosProduktenpåvilkendetursprungligaserienumretharändratselleravlägsnats.

(g) AllnormalförsämringavProdukten,specielltförbrukningsartiklar,tillbehöroch/elleryttredelar(t.ex.knappar,

roterandedelar,kablar,Bruksanvisningenetc.).

(h) Varjedeformation,missfärgningoch/ellerskevhetavProduktensyttreinklusiveytanpåLCD-panelen.

FöratterhållaserviceunderdennagarantimåstedenUrsprungligeköparen(medhänseendetillriskenförskada

och/ellerförlustundertransport)levereraProduktentillnärmasteDistributörmedförebetaldfrakt,idessursprungliga

förpackningellerannanfullgodförpackningsomgerlikvärdigtskydd.DenUrsprungligeköparenmåstekunnavisa

inköpsbevisförProduktensomklargörProduktensinköpsdatumvidbegäranavgarantiservice.

Garantiperiodenförallautbyttaoch/ellerrepareradeprodukterunderdennagarantiskallupphöravidutgångenavden

ursprungligaGarantiperioden.

EIZOELLERDISTRIBUTÖRERÄRINTEANSVARIGAFÖRNÅGONFORMAVSKADAELLERFÖRLUSTAVDATA

ELLERANNANINFORMATIONSOMHARLAGRATSINÅGONFORMAVMEDIAELLERANNANDELAVNÅGON

PRODUKTSOMHARRETURNERATSTILLEIZOELLERDISTRIBUTÖRERFÖRREPARATION.

EIZOOCHDISTRIBUTÖRERNAGARANTERARINGET,UTTRYCKLIGENELLERUNDERFÖRSTÅTT,VAD

BETRÄFFARPRODUKTENOCHDESSKVALITET,PRESTANDA,SÄLJBARHETELLERLÄMPLIGHETFÖRNÅGON

FORMAVSPECIELLANVÄNDNING.UNDERINGAOMSTÄNDIGHETERSKALLEIZOELLERDISTRIBUTÖRERNA

HÅLLASANSVARIGAFÖRNÅGRASOMHELSTUNDERORDNADE,INDIREKTA,SPECIELLA,DÄRAVFÖLJANDE

ELLERÖVRIGASKADOR(INKLUSIVE,UTANBEGRÄNSNINGTILL,SKADORFÖRFÖRLUSTAVINKOMST,

AVBRUTENAFFÄRSRÖRELSE,FÖRLUSTAVAFFÄRSINFORMATIONELLERANNANSÄRSKILDFÖRLUST)SOM

UPPSTÅTTSOMETTRESULTATAVANVÄNDNINGELLEROFÖRMÅGAATTANVÄNDAPRODUKTENELLERI

NÅGONFORMAVANSLUTNINGTILLPRODUKTERNA,VARESIGDETTAGRUNDASPÅKONTRAKT,ÅTALBAR

HANDLING,FÖRSUMLIGHET,ANSVARSSKYLDIGHETELLERANNAT,ÄVENOMEIZOELLERDISTRIBUTÖRERNA

HARINFORMERATSBETRÄFFANDEMÖJLIGHETATTSÅDANASKADORFÖRELIGGER.DETTAUNDANTAG

OMFATTARÄVENALLFORMAVANSVARSSKYLDIGHETSOMKANUPPSTÅGENOMENTREDJEPARTSANSPRÅK

GENTEMOTDENURSPRUNGLIGEKÖPAREN.GRUNDBESTÅNDSDELENIBESTÄMMELSENÄRATTBEGRÄNSA

DETEVENTUELLAANSVARSTAGANDETFÖREIZOOCHDISTRIBUTÖRERNASOMKANUPPSTÅGENOMDENNA

BEGRÄNSADEGARANTIOCH/ELLERFÖRSÄLJNING.

Appendix

ΠΕΡΙΟΡΙΣΜΕΝΗ ΕΓΓΥΗΣΗ

ΗEIZONANAOCORPORATION(στοεξής«EIZO»)καιοιδιανομείςπουεξουσιοδοτείηEIZO(στοεξής«Διανομείς»)

παρέχουνεγγύηση,υποκείμενηκαισύμφωναμετουςόρουςτηςπαρούσαςπεριορισμένηςεγγύησης(στοεξής

«Εγγύηση»),στοναρχικόαγοραστή(στοεξής«Αρχικός Αγοραστής»)οοποίοςαγόρασετοπροϊόνπουκαθορίζεταιστο

παρόνέγγραφο(στοεξής«Προϊόν»)απότηνEIZOήτουςΔιανομείς,ηοποίαεξασφαλίζειότιηEIZOκαιοιΔιανομείς,

σύμφωναμετηδιακριτήευχέρειάτους,είτεθαεπισκευάσουνείτεθααντικαταστήσουντοΠροϊόνχωρίςχρέωσηεάνο

ΑρχικόςΑγοραστήςαντιληφθείεντόςτηςΠεριόδουΕγγύησης(ορίζεταικατωτέρω)ότιτοΠροϊόνδυσλειτουργείήέχει

υποστείβλάβηκατάτηδιάρκειακανονικήςχρήσηςτουΠροϊόντοςσύμφωναμετηνπεριγραφήστοεγχειρίδιοχρήσηςπου

συνοδεύειτοΠροϊόν(στοεξής«Εγχειρίδιο Χρήστη»).

ΗπερίοδοςτηςπαρούσαςΕγγύησηςείναι(i)πέντε(5)έτηαπότηνημερομηνίααγοράςτουΠροϊόντος,ή,στηλήξητων

(ii)30.000ωρώνχρήσηςτουΠροϊόντος(στοεξής«Περίοδος Εγγύησης»).ΗEIZOκαιοιΔιανομείςδενφέρουνκαμία

ευθύνηήυποχρέωσηόσοναφοράτοΠροϊόνσεσχέσημετονΑρχικόΑγοραστήήοποιοδήποτετρίτομέρος,ούτεάλλη

ευθύνηδιαφορετικήαπόαυτήνπουπαρέχεταιστηνπαρούσαΕγγύηση.

ΗEIZOκαιοιΔιανομείςθαπαύσουνναδιατηρούνήνααποθηκεύουντυχόνεξαρτήματατουΠροϊόντοςκατόπιντηςλήξης

τωνεπτά(7)ετώνμετάτηδιακοπήτηςπαραγωγήςτέτοιωνεξαρτημάτων.Κατάτηνεπισκευήτηςοθόνης,ηEIZOκαιοι

ΔιανομείςθαχρησιμοποιήσουνανταλλακτικάεπισκευήςπουσυμμορφώνονταιμεταπρότυπάμαςγιατηΔιασφάλιση

Ποιότητας.

ΗΕγγύησηισχύειμόνοσεχώρεςήπεριοχέςόπουβρίσκονταιοιΔιανομείς.ΗΕγγύησηδενπεριορίζειοποιαδήποτε

νόμιμαδικαιώματατουΑρχικούΑγοραστή.

ΛαμβανομένηςυπόψηκάθεδιάταξηςτηςπαρούσαςΕγγύησης,ηEIZOκαιοιΔιανομείςδενθαέχουνκαμίααπολύτως

υποχρέωσησύμφωναμετηνπαρούσαΕγγύησησεοποιαδήποτεαπότιςπεριπτώσειςπουδιατυπώνονταικατωτέρω:

(α) ΤυχόνελάττωματουΠροϊόντοςπουπροκαλείταιαπόζημιάκατάτημεταφορά,τροποποίηση,αλλαγή,κατάχρηση,

λανθασμένηχρήση,ατύχημα,λανθασμένηεγκατάσταση,καταστροφή,εσφαλμένησυντήρησηή/καιλανθασμένη

επισκευήαπότρίτομέροςεκτόςτηςEIZOκαιτωνΔιανομέων,

(β) ΤυχόνασυμβατότητατουΠροϊόντοςλόγωπιθανώντεχνικώνκαινοτομιώνή/καικανονισμών,

(γ) Τυχόνεπιδείνωσητουαισθητήρα,

(δ) Τυχόνεπιδείνωσητηςαπόδοσηςοθόνηςπουπροκαλείταιαπότηφθοράαναλώσιμωνεξαρτημάτωνόπως

τηςοθόνηςLCDή/καιτουφωτόςυποβάθρου,κτλ.(π.χ.αλλαγέςστηφωτεινότητα,αλλαγέςστηνομοιομορφία

φωτεινότητας,αλλαγέςστοχρώμα,αλλαγέςστηνομοιομορφίαχρώματος,ελαττώματασεpixelπεριλαμβανομένων

τωνκαμένωνpixel,κτλ.),

(ε) ΤυχόνελάττωματουΠροϊόντοςπουπροκαλείταιαπόεξωτερικόεξοπλισμό,

(στ)ΤυχόνελάττωματουΠροϊόντοςστοοποίοέχειτροποποιηθείήαφαιρεθείογνήσιοςαριθμόςσειράς,

(ζ) Τυχόν φυσιολογική φθορά του προϊόντος, ιδιαίτερα αυτής των αναλώσιµων, των αξεσουάρ ή/και των

προσαρτηµάτων(π.χ.κουµπιά,περιστρεφόµεναµέρη,καλώδια,ΕγχειρίδιοΧρήστη,κτλ.),και

(η) Τυχόν παραμόρφωση, αποχρωματισμό ή/και διαστρέβλωση του εξωτερικού μέρους του προϊόντος,

περιλαμβανομένηςτηςεπιφάνειαςτηςοθόνηςLCD.

ΟΑρχικόςΑγοραστήςγιαναδικαιούταιυπηρεσίεςεπισκευήςσύμφωναμετηνΕγγύηση,θαπρέπειναπαραδώσειτο

Προϊόν,μεπληρωμέναταμεταφορικάέξοδα,στηναρχικήτουσυσκευασίαήσεάλληεπαρκήσυσκευασίαμεισότιμο

βαθμόπροστασίας,αναλαμβάνονταςτονκίνδυνοβλάβηςή/καιαπώλειαςκατάτημεταφορά,στοντοπικόΔιανομέα.Ο

ΑρχικόςΑγοραστήςότανζητάυπηρεσίεςεπισκευήςσύμφωναμετηνΕγγύηση,θαπρέπειναπροσκομίζειτηναπόδειξη

αγοράςτουΠροϊόντοςκαιτηνημερομηνίατηςαγοράς.

ΗΠερίοδοςΕγγύησηςγιαοποιοδήποτεαντικατεστημένοή/καιεπισκευασμένοπροϊόνσύμφωναμετηνπαρούσα

ΕγγύησηλήγειστοτέλοςτηςαρχικήςΠεριόδουΕγγύησης.

ΗEIZOΉΟΙΔΙΑΝΟΜΕΙΣΔΕΝΕΥΘΥΝΟΝΤΑΙΓΙΑΟΠΟΙΑΔΗΠΟΤΕΒΛΑΒΗΉΑΠΩΛΕΙΑΔΕΔΟΜΕΝΩΝΉΑΛΛΩΝ

ΠΛΗΡΟΦΟΡΙΩΝΠΟΥΑΠΟΘΗΚΕΥΟΝΤΑΙΣΕΟΠΟΙΟΔΗΠΟΤΕΜΕΣΟΉΟΠΟΙΟΔΗΠΟΤΕΑΛΛΟΜΕΡΟΣΣΕ

ΟΠΟΙΟΔΗΠΟΤΕΠΡΟΪΟΝΠΟΥΕΠΙΣΤΡΕΦΕΤΑΙΣΤΗΝEIZOΉΣΕΔΙΑΝΟΜΕΑΓΙΑΕΠΙΣΚΕΥΗ.

ΗEIZOΚΑΙΟΙΔΙΑΝΟΜΕΙΣΔΕΝΠΑΡΕΧΟΥΝΚΑΜΙΑΠΕΡΑΙΤΕΡΩΕΓΓΥΗΣΗ,ΡΗΤΗΉΣΥΝΕΠΑΓΟΜΕΝΗ,ΟΣΟΝ

ΑΦΟΡΑΤΟΠΡΟΪΟΝΚΑΙΤΗΝΠΟΙΟΤΗΤΑ,ΤΗΝΑΠΟΔΟΣΗ,ΤΗΝΕΜΠΟΡΕΥΣΙΜΟΤΗΤΑΉΤΗΝΚΑΤΑΛΛΗΛΟΤΗΤΑ

ΤΟΥΓΙΑΟΠΟΙΑΔΗΠΟΤΕΣΥΓΚΕΚΡΙΜΕΝΗΧΡΗΣΗ.ΣΕΚΑΜΙΑΠΕΡΙΠΤΩΣΗΗEIZOΉΟΙΔΙΑΝΟΜΕΙΣΔΕΝ

ΘΑΕΥΘΥΝΟΝΤΑΙΓΙΑΚΑΜΙΑΑΠΟΛΥΤΩΣΤΥΧΑΙΑ,ΕΜΜΕΣΗ,ΕΙΔΙΚΗ,ΣΥΝΕΠΑΓΟΜΕΝΗΉΑΛΛΗΒΛΑΒΗ

(ΠΕΡΙΛΑΜΒΑΝΟΜΕΝΩΝ,ΜΕΤΑΞΥΑΛΛΩΝ,ΒΛΑΒΩΝΉΑΠΩΛΕΙΑΣΚΕΡΔΩΝ,ΔΙΑΚΟΠΗΣΕΠΙΧΕΙΡΗΜΑΤΙΚΩΝ

ΔΡΑΣΤΗΡΙΟΤΗΤΩΝ,ΑΠΩΛΕΙΑΣΕΠΙΧΕΙΡΗΜΑΤΙΚΩΝΠΛΗΡΟΦΟΡΙΩΝΉΤΥΧΟΝΑΛΛΗΣΧΡΗΜΑΤΙΚΗΣΑΠΩΛΕΙΑΣ)

ΠΟΥΠΡΟΚΥΠΤΕΙΑΠΟΤΗΧΡΗΣΗΉΤΗΝΑΝΙΚΑΝΟΤΗΤΑΧΡΗΣΗΣΤΟΥΠΡΟΪΟΝΤΟΣΉΤΥΧΟΝΑΛΛΗΣΣΥΝΔΕΣΗΣ

ΜΕΤΟΠΡΟΪΟΝ,ΕΙΤΕΒΑΣΙΖΕΤΑΙΣΕΣΥΜΒΟΛΑΙΟ,ΒΛΑΒΗ,ΑΜΕΛΕΙΑ,ΑΥΣΤΗΡΗΕΥΘΥΝΗΉΕΙΔΑΛΛΩΣ,ΑΚΟΜΗ

ΚΙΕΑΝΗEIZOΉΟΙΔΙΑΝΟΜΕΙΣΕΝΗΜΕΡΩΘΟΥΝΓΙΑΤΗΝΠΙΘΑΝΟΤΗΤΑΤΕΤΟΙΩΝΖΗΜΙΩΝ.ΗΕΞΑΙΡΕΣΗΑΥΤΗ

ΠΕΡΙΛΑΜΒΑΝΕΙΕΠΙΣΗΣΟΠΟΙΑΔΗΠΟΤΕΕΥΘΥΝΗΕΝΔΕΧΕΤΑΙΝΑΠΡΟΚΥΨΕΙΑΠΟΑΞΙΩΣΕΙΣΤΡΙΤΟΥΜΕΡΟΥΣ

ΚΑΤΑΤΟΥΑΡΧΙΚΟΥΑΓΟΡΑΣΤΗ.ΗΟΥΣΙΑΤΟΥΟΡΟΥΑΥΤΟΥΕΙΝΑΙΝΑΠΕΡΙΟΡΙΣΕΙΤΗΝΠΙΘΑΝΗΕΥΘΥΝΗΤΗΣ

EIZOΚΑΙΤΩΝΔΙΑΝΟΜΕΩΝΠΟΥΠΡΟΚΥΠΤΕΙΑΠΟΤΗΝΠΑΡΟΥΣΑΕΓΓΥΗΣΗΉ/ΚΑΙΤΙΣΠΩΛΗΣΕΙΣ.

Appendix

ОГРАНИЧЕННАЯ ГАРАНТИЯ

EIZONANAOCORPORATION(называемаявдальнейшем“EIZO”)иавторизированныеEIZOдистрибуторы

(называемыевдальнейшем“Дистрибуторы”)гарантируют,всоответствиисусловиямиипунктамиэтой

ограниченнойгарантии(называемойвдальнейшем“Гарантия”),первичномупокупателю(называемомув

дальнейшем“Первоначальный покупатель”),которыйприобрелуEIZOилиДистрибуторовпродукт,указанный

вэтомдокументе(называемыйвдальнейшем“Продукт”),чтоEIZOилиДистрибуторынасвоеусмотрение

либобесплатноотремонтируют,либобесплатнозаменятПродукт,еслиПервоначальныйпокупательпризнает

впределахГарантийногосрока(определенногониже),чтоПродуктнеисправенилионповрежденпроцессе

нормальногоиспользованияпродуктавсоответствиисописаниемвинструкциипоэксплуатации,прилагаемойк

Продукту(называемойвдальнейшем“Руководство пользователя”).

Гарантийныйпериодограниченсроком(i)пять(5)летотдатыприобретенияПродуктаилиограниченсроком

(ii)30000часовиспользованияПродукта(называемыйвдальнейшем“Гарантийный период”).EIZOи

ДистрибуторыненесутникакойответственностиинеберутобязательствотносительноПродуктапоотношениюк

Первоначальномупокупателюилипоотношениюклюбымтретьимсторонам,кромеобязательств,оговоренныхв

этойГарантии.

EIZOиДистрибуторыпрекратятхранениеилискладированиелюбыхдеталейПродуктапоистечениисеми(7)

летпослепрекращенияпроизводстватакихдеталей.ВслучаеремонтамонитораEIZOиДистрибьюторыбудут

использоватьзапчасти,которыесоответствуютнашимстандартамQC(контролькачества).

Гарантиядействительнатольковстранахилирегионах,гдерасположеныДистрибуторы.Гарантияне

ограничиваетникакиезаконныеправаПервоначальногопокупателя.

НесмотрянадругиеусловияэтойГарантииEIZOиДистрибуторыненесутникакихобязательствсогласноэтой

Гарантиивлюбомизперечисленныхнижеслучаев:

(а) ЛюбыедефектыПродукта,вызванныеповреждениямиприперевозке,модификацией,изменением,

неправильнымобращением,неправильнымиспользованием,авариями,неправильнойустановкой,

стихийнымибедствиями,неправильнымуходоми/илинеправильнымремонтомтретьейстороной,отличной

отEIZOилиДистрибуторов;

(б) ЛюбыенесовместимостиПродуктаиз-затехническихусовершенствованийи/илиизменениятехнических

норм;

(в) Любоеповреждениедатчика;

(г) Любыеухудшенияработыдисплея,вызванныеизнашиваниемневосстановимыхчастей,такихкак

панельЖКДи/илиподсветкаит.д.(например,изменениевяркости,изменениевравномерностияркости,

изменениевцветности,изменениевравномерностицветности,изменениевпикселах,включаявыгоревшие

пикселыит.д.);

(д) ЛюбыедефектыПродукта,вызванныевнешнимоборудованием;

(е) ЛюбыедефектыПродукта,прикоторыхоригинальныйсерийныйномербылизмененилиудален;

(ж) Любые естественные ухудшения продукта, в частности, вызванные износом расходных частей,

принадлежностейи/илиприспособлений(например,кнопок,вращающихсячастей,кабелей,Руководства

пользователяит.д.);и

(з) Любыедеформации,измененияцветаи/иликороблениявнешнейповерхностипродукта,включая

поверхностьпанелиЖКД.

ЧтобыполучитьтехническоеобслуживаниеврамкахГарантии,Первоначальныйпокупательдолжендоставить

ПродуктместномуДистрибутору,оплативперевозку,вегооригинальнойупаковкеиливдругойсоответствующей

упаковке,обеспечивающейравноценнуюстепеньзащиты,принимаявовниманиерискповрежденияи/илиутерюпри

транспортировке.ПризапросетехническогообслуживанияврамкахГарантииПервоначальныйпокупательдолжен

предоставитьсвидетельствопокупкипродуктаидатыпокупки.

Гарантийныйпериоддлялюбогозамененногои/илиотремонтированногопродуктаврамкахГарантииистекаетвконце

завершениясрокадействияоригинальногоГарантийногопериода.

EIZOИЛИДИСТРИБУТОРЫНЕНЕСУТОТВЕТСТВЕННОСТИЗАЛЮБЫЕПОВРЕЖДЕНИЯИЛИУТЕРЮДАННЫХИЛИ

ДРУГОЙИНФОРМАЦИИ,ХРАНЯЩИХСЯНАКАКИХ-ЛИБОНОСИТЕЛЯХИНФОРМАЦИИИЛИНАЛЮБЫХДРУГИХ

ЧАСТЯХПРОДУКТА,КОТОРЫЙВОЗВРАЩЕНEIZOИЛИДИСТРИБУТОРАМДЛЯРЕМОНТА.

EIZOИДИСТРИБУТОРЫНЕДАЮТНИКАКОЙДАЛЬНЕЙШЕЙГАРАНТИИ,ВЫРАЖЕННОЙИЛИПОДРАЗУМЕВАЕМОЙ,

ОТНОСИТЕЛЬНО ПРОДУКТА И ЕГО КАЧЕСТВА, ТЕХНИЧЕСКИХ ХАРАКТЕРИСТИК, ТОВАРНОСТИ ИЛИ

СООТВЕТСТВИЯДЛЯКАКОГО-ЛИБООПРЕДЕЛЕННОГОИСПОЛЬЗОВАНИЯ.НИПРИКАКИХУСЛОВИЯХEIZO

ИЛИДИСТРИБУТОРЫНЕНЕСУТОТВЕТСТВЕННОСТИЗАЛЮБОЙСЛУЧАЙНЫЙ,КОСВЕННЫЙ,СПЕЦИАЛЬНЫЙ,

ПОБОЧНЫЙИЛИИНОЙУЩЕРБ(ВКЛЮЧАЯ,БЕЗОГРАНИЧЕНИЙ,УЩЕРБИЗ-ЗАНЕПОЛУЧЕННОЙПРИБЫЛИ,

ПРЕРЫВАНИЯ БИЗНЕСА, ПОТЕРИ КОММЕРЧЕСКОЙ ИНФОРМАЦИИ ИЛИ ЛЮБЫЕ ДРУГИЕ ФИНАНСОВЫЕ

ПОТЕРИ),ВОЗНИКШИЙИЗ-ЗАИСПОЛЬЗОВАНИЯИЛИНЕВОЗМОЖНОСТИИСПОЛЬЗОВАТЬПРОДУКТИЛИВ

ЛЮБОЙДРУГОЙСВЯЗИСПРОДУКТОМ,ЛИБООСНОВАННЫЙНАКОНТРАКТНЫХОТНОШЕНИЯХ,ГРАЖДАНСКИХ

ПРАВОНАРУШЕНИЯХ,НЕБРЕЖНОСТИ,ПРИЧИНЕНИЯУЩЕРБАТРЕТЬЕЙСТОРОНЕИЛИЧЕМ-ЛИБОЕЩЕ,ДАЖЕ

ЕСЛИEIZOИЛИДИСТРИБУТОРЫБЫЛИУВЕДОМЛЕНЫОВОЗМОЖНОСТИТАКОГОУЩЕРБА.ЭТОИСКЛЮЧЕНИЕ

ТАКЖЕВКЛЮЧАЕТЛЮБЫЕОБЯЗАТЕЛЬСТВА,КОТОРЫЕМОГУТВОЗНИКНУТЬВРЕЗУЛЬТАТЕТРЕБОВАНИЙ

ТРЕТЬЕЙСТОРОНЫВОТНОШЕНИИПЕРВОНАЧАЛЬНОГОПОКУПАТЕЛЯ.СУЩЕСТВОМЭТОГОПОЛОЖЕНИЯ

ЯВЛЯЕТСЯОГРАНИЧЕНИЕПОТЕНЦИАЛЬНОЙОТВЕТСТВЕННОСТИEIZOИДИСТРИБУТОРОВ,ВОЗНИКАЮЩЕЙИЗ-

ЗАЭТОЙОГРАНИЧЕННОЙГАРАНТИИИ/ИЛИПРОДАЖ.

Appendix

有限责任保证书

EIZONANAO 有限公司以下简称 EIZO 和EIZO 授权的经销商以下简称经销商

”），

接受并依照本有限责任保证书

（

“

”）

（

“

以下简称保证书之条款向从EIZO 和经销商购买本文中所规定产品以下简称产品的原买方以下称原买方

”） ”） ”）

（

“

，

（

“

（

“

提供保证在保证期内规定如下如果原买方发现按本产品所附使用说明书以下简称用户手册所述方式正常使

）， ”）

：

（

“

用本产品过程中本产品出现故障或损坏 EIZO 和经销商根据其独自的判断免费修理或更换该产品

。

，

本保证期限定为 i 自本产品购买之日起的五 5 年期间或限定为到达 ii 使用本产品3 万小时的期限以下简称保证期限

（）（）（） ”）。

（

“

EIZO和经销商将不向原买方或任何第三方承担本保证书所规定之外的与本产品有关的任何责任或义务

。

本产品的任何部件停产七(7) 年后 EIZO 和经销商将不再保留或保管任何这类部件维修显示器时 EIZO 与经销商将使

，

用符合我方质量控制标准的替换零件

。

，

。

本保证书仅对于设有经销商的国家或地区有效本保证书并不限定原买方的任何法律权利

。

无论本保证书的任何其他条款如何规定对于任何下列情况之一 EIZO 和经销商将不承担本保证书规定责任

，

：

(a) 由于运输损害改装改动滥用误用意外事故错误安装灾害维护不善和/ 或由除EIZO 和经销商以外的

、

第三方进行不适当的修理造成本产品的任何故障

、

。

(b) 由于可能发生的技术变更和/ 或调整造成本产品的任何不兼容性

。

(d) 由于诸如液晶显示屏 LCD 和/ 或背灯等消耗品部件的老化造成的任何显示性能低劣如亮度变化亮度均一性变化

（

色彩变化色彩均一性变化如烧伤像素等像素缺陷

）

（

、

）。

(e) 因外部设备造成本产品的任何故障

。

(f) 因本产品的原序号被改变或消除造成本产品的任何故障

。

(g) 本产品的任何正常老化尤其是消耗品附件和/ 或附加装置如按钮旋转部件电缆用户手册等以及

）、

，

、

（

、

(h) 本产品表面包括液晶显示屏 LCD 表面的任何变形变色和/ 翘曲

。

（

）

、

为了获得本保证书规定的服务原买方必须使用原包装或其他具有同等保护程度的适当包装将本产品运送到当地的经销商

，

并且预付运费承担运输中的损坏和/ 或损失的风险要求提供本保证书规定的服务时原买方必须提交购买本产品和标

，

明此购买日期的证明

。

，

。

按本保证书规定进行了更换和/ 或修理的任何产品的保证期限将在原保证期限结束时终止

，

。

在返回给EIZO 和经销商进行修理后任何产品的任何媒体或任何部件中储存的数据或其他信息发生任何损坏或损失对

，

此EIZO 和经销商将不承担责任

。

对于本产品及其质量性能可销售性以及对于特殊用途的适合性 EIZO 和经销商不提供其他任何明示或暗示的保证因

、

，

。

使用本产品或无法使用本产品或因与本产品有任何关系无论是否根据合同而造成: 任何附带的间接的特殊的随

（

）

、

之发生的或其他的损害包括但不仅限于利润损失业务中断业务信息丢失或其他任何金钱损失以及侵权行为过失

（

：

、

）

、

。

严格赔偿责任或其他责任即使已经向EIZO 和经销商提出了发生这些损害的可能性对此EIZO 和经销商概不承担责任

，

本免责条款还包括因第三方向原买方提出索赔而可能发生的任何责任本条款的本质是限定由于本有限责任保证书和/ 或

销售本产品所发生的EIZO 和经销商的潜在责任

。

Appendix

Recycling Information

This product, when disposed of, is supposed to be collected and recycled according to your country’s

legislation to reduce environmental burden. When you dispose of this product, please contact a distributor or

an afﬁliate in your country.

The contact addressees are listed on the EIZO website below.

http://www.eizo.com

For recycling information for customers in Switzerland, please refer to the following website.

http://www.swico.ch

Informationen zum Thema Recycling

Dieses Produkt muss gemäß den Vorschriften Ihres Landes zur Entlastung der Umwelt recyclet werden.

Wenden Sie sich bei der Entsorgung dieses Produkts an einen Verteiler oder eine Tochtergesellschaft in

Ihrem Land.

Die Adressen zur Kontaktaufnahme sind auf der unten angegebenen Website von EIZO aufgeführt.

http://www.eizo.com

Kunden in der Schweiz entnehmen Informationen zum Recycling der folgenden Website:

http://www.swico.ch

Informations sur le recyclage

Ce produit doit être jeté aux points de collecte prévus à cet effet et recyclé conformément à la législation de

votre pays, aﬁn de réduire l’impact sur l’environnement. Lorsque vous jetez ce produit, veuillez contacter un

distributeur ou une société afﬁliée de votre pays.

Les adresses des distributeurs sont répertoriées sur le site Web EIZO ci-dessous.

http://www.eizo.com

Pour les clients en Suisse, veuillez consulter le site Web suivant afin d’obtenir des informations sur le

recyclage.

http://www.swico.ch

Información sobre reciclaje

Este producto debe desecharse y reciclarse según la legislación del país para reducir el impacto

medioambiental. Cuando desee deshacerse de este producto, póngase en contacto con un distribuidor o

una ﬁlial de su país.

Encontrará las direcciones de contacto en el sitio web de EIZO que se indica a continuación.

http://www.eizo.com

Informazioni sul riciclaggio

Per lo smaltimento e il riciclaggio del presente prodotto, attenersi alle normative vigenti nel proprio paese per

ridurre l’impatto ambientale. Per lo smaltimento, rivolgersi ad un distributore o un afﬁliato presenti nel proprio

paese.

Gli indirizzi sono elencati nel sito Web EIZO riportato di seguito.

http://www.eizo.com

Per informazioni sul riciclaggio per i clienti in Svizzera, consultare il sito Web riportato di seguito.

http://www.swico.ch

Återvinningsinformation

När denna produkt kasseras ska den hanteras och återvinnas enligt landets föreskrifter för att reducera

miljöpåverkan. När du kasserar produkten ska du kontakta en distributör eller representant i ditt land.

Kontaktadresserna listas på EIZO-webbplatsen nedan.

http://www.eizo.com

Appendix

Πληροφορίες ανακύκλωσης

Τοπροϊόναυτό,όταναπορρίπτεται,πρέπεινασυλλέγεταικαιναανακυκλώνεταισύμφωναμετηνομοθεσία

τηςχώραςσαςέτσιώστεναμηνεπιβαρύνειτοπεριβάλλον.Γιανααπορρίψετετοπροϊόν,επικοινωνήστεμε

έναναντιπρόσωποήμιαθυγατρικήεταιρείαστηχώρασας.

ΟιδιευθύνσειςεπικοινωνίαςαναγράφονταιστηντοποθεσίαwebτηςEIZOπαρακάτω.

http://www.eizo.com

Сведения по утилизации

По истечении срока службы данного продукта его следует принести на сборный пункт и

утилизироватьвсоответствиисдействующимипредписаниямиввашейстране,чтобыуменьшить

вредноевоздействиенаокружающуюсреду.Преждечемвыброситьданныйпродукт,обратитеськ

дистрибьюторуиливместноепредставительствокомпанииввашейстране.

Контактныеадресаможнонайтинавеб-узлеEIZO.

http://www.eizo.com

Informatie over recycling

Wanneeruditproductwiltweggooien,moethetuitmilieu-overwegingenwordenverzameldengerecycled

volgensdebetreffendewetgevingvanuwland.Wanneeruditproductwiltweggooien,moetucontact

opnemenmeteendistributeurofeenpartnerinuwland.

DecontactadressenwordenvermeldopdevolgendeEIZO-website.

http://www.eizo.com

Informação sobre reciclagem

Esteproduto,quandoodeitarfora,deveserrecolhidoerecicladodeacordocomalegislaçãodoseupaís

parareduzirapoluição.Quandodeitarforaesteproduto,contacteumdistribuidorouuma lialnoseupaís.

OsendereçosdecontactoestãolistadosnowebsitedoEIZO,abaixo.

http://www.eizo.com

Oplysninger om genbrug

Detteproduktforventesvedbortskaffelseatbliveindsamletoggenbrugtioverensstemmelsemed

lovgivningeniditlandforatreducerebelastningenafmiljøet.Nårdubortskafferdenneprodukt,skaldu

kontakteendistributørellerettilknyttetselskabiditland.

AdressernepåkontaktpersonerneerangivetpåEIZO’swebstednedenfor.

http://www.eizo.com

Kierrätystä koskevia tietoja

Tuote tulee hävittää kierrättämällä maan lainsäädännön mukaisesti ympäristön kuormittumisen

vähentämiseksi.Kunhävitättuotteen,otayhteyttäjälleenmyyjääntaitytäryhtiöönmaassasi.

YhteystiedotlöytyvätEIZOnInternet-sivustolta.

http://www.eizo.com

Wykorzystanie surowców wtórnych

Tenproduktpozużyciupowinienbyćzbieranyiprzetwarzanyzgodniezkrajowymiprzepisamidotyczącymi

ochronyśrodowiska.Wyrzucająctenprodukt,należyskontaktowaćsięzlokalnymdystrybutoremlub

partnerem.Adresykontaktowemożnaznaleźćwewskazanejponiżejwitrynieinternetowej rmyEIZO.

http://www.eizo.com

Appendix

Informace o recyklaci

Přilikvidaciproduktumusíbýtproduktvyzvednutarecyklovánpodlezákonůpříslušnézemě,aby

nedocházelokzatěžováníživotníhoprostředí.Zbavujete-liseproduktu,kontaktujtedistributoranebo

pobočkuvesvézemi.KontaktníadresyjsouuvedenynanásledujícíwebovéstráncespolečnostiEIZO.

http://www.eizo.com

Ringlussevõtu alane teave

Keskkonnakoormusevähendamisekstulekskasutatudtootedkokkukogudajavõttaringlussevastavaltteie

riigiseadustele.Kuikõrvaldatekäesolevatoote,võtkepalunühendustturustajavõi liaaligaomariigis.

KontaktisikudontoodudEIZOveebileheljärgmiselaadressil:

http://www.eizo.com

Újrahasznosítási információ

Jelenterméket,amikoreldobjuk,azilletőországtörvényeialapjánkellösszegyűjteniésújrahasznosítani,

hogycsökkentsükakörnyezetterhelését.Amikoreztaterméketeldobja,kérjüklépjenkapcsolatbaegy

országonbelüliforgalmazóvalvagytársvállalkozással.

AkapcsolatcímeiazEIZOalábbiweboldalántalálhatókfelsorolva:

http://www.eizo.com

Podatki o recikliranju

Obkoncuuporabeodsluženizdelekizročitenazbirnomestozarecikliranjevskladuzokoljevarstveno

zakonodajovašedržave.Prosimo,dasepriodstranjevanjuizdelkaobrnetenalokalnegadistributerjaali

podružnico.

KontaktninaslovisoobjavljeninaspodajnavedenihspletnihstranehEIZO:

http://www.eizo.com

Informácie o recyklácii

Prilikvidáciimusíbyťtentovýrobokrecyklovanývsúladeslegislatívouvašejkrajiny,abysaznížilozaťaženie

životnéhoprostredia.Keďsachcetezbaviťtohtovýrobku,kontaktujteprosímdistribútoraalebopobočkuvo

vašejkrajine.

Zoznamkontaktnýchadriesjeuvedenýnanasledovnejwebovejstránke rmyEIZO:

http://www.eizo.com

Pārstrādes informācija

Utilizējotšoproduktu,tāsavākšanaunpārstrādeveicamaatbilstošijūsuvalstslikumdošanasprasībām

attiecībāuzslodzesuzvidisamazināšanu.Laiveiktušīproduktautilizāciju,sazinietiesarizplatītājuvai

pārstāvniecībujūsuvalstī.

KontaktadresesirnorādītaszemākminētajāEIZOtīmekļavietnē.

http://www.eizo.com

Informacija apie grąžinamąjį perdirbimą

Šalinant(išmetant)šiuosgaminiusjuosreikiasurinktiirperdirbtigrąžinamuojubūdupagaljūsųšaliesteisės

aktus,siekiantsumažintiaplinkosteršimą.Kaireikiaišmestišįgaminį,kreipkitėsįjūsųšalyjeveikiančią

gaminiųpardavimoatstovybęarbajos lialą.

KontaktiniaiadresatainurodytiEIZOinternetosvetainėje.

http://www.eizo.com

Appendix

Информация относно рециклиране

Приизхвърлянетонатозипродуктсепредлагасъбиранетоирециклиранетомусъобразнозаконитена

вашатастраназадасенамализамърсяванетонаоколнатасреда.Когатоискатедасеосвободитеот

тозипродукт,молясвържетесестърговскиямупредставителилисъссъответнитеорганиотговарящи

затовавъввашатастрана.

ДаннитезавръзкаснассаописанинаследнияИнтернетсайтнаEIZO:

http://www.eizo.com

Informaţie referitoare la reciclare

Acestprodus,cânddebarasat,trebuiecolectatşireciclatconformlegislaţieiţăriirspectivecasăreducem

sarcinamediului.Cândsedebaraseazădeacestprodus,vărugămsăcontactaţiundistribuitorsauuna liat

alţăriirespective.

AdreseledecontactlegăsiţipepaginadewebalEIZO:

http://www.eizo.com

Geri Dönüşüm Bilgisi

Buürünün,atılacağızaman,ülkenizinçevrekirliliğininazaltılmasıkonusundakimevzuatınagöretoplanması

veyenidendeğerlendirilmesigerekmektedir.Ürünüatacağınızzamanlütfenülkenizdekibirdistribütörveya

ilgilikuruluşlatemasageçiniz.

İrtibatadresleriaşağıdakiEIZOwebsitesindeverilmiştir.

http://www.eizo.com

Appendix

China Measures for RoHS Compliance in ChinaRoHS

关于电子信息产品污染控制标识

本标识根据「电子信息产品污染控制管理办法」，适用于在中华人民共和国销售的电子信息产品。标识中央的

数字为环保使用期限的年数。只要您遵守该产品相关的安全及使用注意事项，在自制造日起算的年限内，不会

产生对环境污染或人体及财产的影响。上述标识粘贴在机器背面。

•

有毒有害物质或元素的名称及含量

部件名称

有毒有害物质或元素

铅

（Pb）

汞

（Hg）

○

镉

（Cd）

○

六价铬

（Cr（VI））

多溴联苯

（PBB）

多溴二苯醚

（PBDE）

印刷电路板

机箱

○

液晶显示器

其他

○

○：表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T 11363-2006规定的限量要求以下。

×：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T 11363-2006规定的限量要求。

(企业可在此处,根据实际情況对上表中打“×”的技术原因进行进一步说明)

Appendix

2nd Edition-November, 2012

03V24151B1

(U.M-CX270)

Electrolux SONATA 55LXa User Manual
Dell Computer Monitor E1911 User Manual
Cypress CY7C1415JV18 User Manual
Cypress CY7C1411JV18 User Manual
Channel Vision C 0150D User Manual
Bosch Appliances DHG6015DUC User Manual
Audiovox VOH1012 User Manual
Asus Computer Monitor VW223D User Manual
Amana AMC7159TA User Manual
Advantech PPC 175T User Manual