Eizo FlexScan T550 User Manual

English  
User's Manual  
®
FlexScan  
T550  
Color Display Monitor  
PRECAUTIONS  
IMPORTANT!  
* This product has been adjusted specifically for use in the region to which it was originally shipped.  
The performance of the product, (i.e. picture geometry, picture positioning and color convergence  
and purity in the case of color monitors) is optimally adjusted to the earth's magnetic field of the  
specific destination. If operated outside the region to which it was originally shipped, the product  
may not perform as stated in the specifications.  
E
* The manufacturer is not responsible for damage or malfunction caused by improper connection.  
The power cord should be connected directly to a standard wall power outlet.  
Location of the caution statements  
The equipment must be connected to a grounded main outlet.  
Jordet stikkontakt skal benyttes när apparatet tilkobles datanett.  
Apparaten skall anslutas till jordat nätuttag.  
IMPORTANT!  
To ensure personal safety and proper maintenance. Please read this  
section and the caution statements on the monitor (refer to the figure  
above).  
This manual uses the safety symbols below. They denote critical information.  
Please read them carefully.  
Indicates a prohibited action.  
Indicates to ground for safety.  
WARNING  
Failure to abide by the information in a WARNING may result in serious  
injury and can be life threatening.  
CAUTION  
Failure to abide by the information in a CAUTION may result in moderate  
injury and/or property or product damage.  
WARNING  
• If the monitor begins to emit smoke, smells like something is  
burning, or makes strange noises, disconnect all power  
connections immediately and contact your dealer for advice.  
Attempting to use a malfunctioning monitor can be dangerous.  
• Do not dismantle the cabinet or modify the monitor.  
Dismantling the cabinet or modifying the monitor may result in electric  
shock or burn.  
PRECAUTIONS  
3
• Keep small objects away from the monitor.  
Small objects may accidentally fall through the ventilation slots into the  
cabinet, leading to fire, shock, or equipment damage.  
• Keep liquids away from the monitor.  
Spillage into the cabinet may result in fire, electric shock, or equipment  
damage. If an object or liquid falls/spills into the cabinet, unplug the  
monitor immediately. Have the unit checked by a qualified service engineer  
before using it again.  
• Place the monitor on a strong, stable surface.  
A unit placed on an inadequate surface may fall, resulting in injury or  
equipment damage. If the monitor falls, disconnect the power immediately  
and have the unit checked by a qualified service engineer before using it  
again. Using a monitor after it has been dropped may result in fire or  
electric shock.  
OK  
• Keep the plastic packing bags away from children and infants.  
Plastic bags can be dangerous. To avoid danger of suffocation, keep the  
bag away from babies and children.  
• Keep power terminal covers for the optional i·Soundä sound unit  
away from children and infants.  
Children and infants may accidentally swallow the covers and choke. If  
swallowed, consult a doctor immediately.  
• Use the enclosed power cord. If using the power cord other than the  
enclosed one, use the following cord.  
In USA and Canada:  
* Rating: min. 125 V, 10 A * Length: max. 2.1 m * Type: SVT  
* Plug type:NEMA 5-15P, Parallel blade, Grounding type, 125 V, 10 A  
In Europe:  
* Rating: min. 250 V, 10 A * Length: max. 2.1 m  
* Type:  
H05VV-F 3G 1 mm2  
Use a plug type approved by the country where you use  
Failure to do so may cause fire or electric shock.  
• The equipment must be connected to a grounded main outlet.  
• Use the correct voltage.  
The monitor is designed for use with a specific voltage only. Connection to  
a different voltage may cause fire, electric shock, or other damage.  
• Do not overload your power circuit, as this may result in fire or  
electric shock.  
• For proper connections of the power cord, be certain to plug the  
power cord to the provided monitor connector and directly to a wall  
outlet.  
By not doing so may result in fire or electric shock.  
• Handle the power cord with care.  
* Do not place the cord underneath the monitor or other heavy objects.  
* Do not pull on the cord.  
* Do not attempt to repair a damaged cord.  
If the power cord becomes damaged, stop using it. Use of a damaged cord  
may result in fire or electric shock.  
PRECAUTIONS  
4
• To disconnect the power cord, grasp the plug firmly and pull.  
Never tug on the cord, doing so may cause damage and could result in fire or  
electric shock.  
OK  
E
CAUTION  
• Disconnect the power cord, signal cables and remove the optional  
i·Soundsound unit and i·StationUSB hub (if applicable) when  
moving the monitor.  
Moving the monitor with the cord attached or lifting it by the i·Sound sound  
unit or i·Station USB hub is dangerous. It may result in injury or equipment  
damage.  
• Handle with care when carrying the monitor  
Note that the monitor is heavier at the front than at the rear. Do not move it  
alone. Always work with another person.  
The screen is optically coated to reduce glare. Keep hard objects (such as  
buttons, tie pins, and other clothing accessories) away from the screen surface to  
prevent scratches.  
OK  
• Set the monitor in an appropriate location.  
* Do not install in a dusty or humid environment.  
* Do not place in a location where light shines directly on the screen.  
* Do not place near heat generating devices or a humidifier.  
• Use an easily accessible power outlet.  
This will ensure that you can disconnect the power quickly in case of a problem.  
• Do not sit on the cabinet or place any heavy objects on the cabinet.  
A unit with heavy objects on it may fall or be damaged and result in injury.  
• Do not block the ventilation slots on the cabinet.  
* Do not place books or any other papers on the ventilation slots.  
* Do not install the monitor in a closed space.  
* Do not use the monitor laying down or upside down.  
* Do not remove the tilt-swivel stand.  
Using the monitor in this way blocks the ventilation slots and prevents proper  
airflow, leading to fire or other damage.  
• Do not remove the tilt-swivel stand.  
The stand is required to maintain clearance for the ventilation slots on the  
bottom of the cabinet. Removing the stand will block these slots and may result  
in fire or electric shock.  
• Do not touch the plug with wet hands.  
Touching the plug with wet hands is dangerous and can cause electrical shock.  
• At the end of the day or if you plan to leave the monitor unused for an  
extended period, after turning off the power switch disconnect the power  
cord from the wall socket so that no power connections are made.  
• Unplug the monitor before cleaning it.  
Cleaning the monitor while it is plugged into a power outlet may result in  
electric shock.  
• When adjusting the viewing angle of the monitor, do not do so by  
handling the sound unit or USB hub (if applicable).  
Adjusting the monitor in this way may break the unit or cause bodily injury.  
PRECAUTIONS  
5
Others  
Do not install the monitor within an area subject to strong magnetic  
fields (for example, in the vicinity of a speaker, except the optional  
i·Sound unit, or a high-voltage transformer). Magnetic fields can cause  
noise, image shaking, and other distortions.  
Generally, for maximum viewing comfort position the monitor slightly  
below eye level. Staring at the monitor for prolonged periods can cause  
eye strain. Be sure to take adequate rests. (A 10-minute rest period each  
hour is suggested.)  
Do not remove the covers to the power terminal for the optional i·Sound  
speaker unit for any reason except to attach the unit.  
PRECAUTIONS  
6
INTRODUCTION  
About This Manual  
This manual explains the precautions, specifications, and operation of your EIZO  
monitor. Please read through this manual as it will help you to get the most out of  
your monitor.  
E
Controls & Connectors:  
Front  
Power indicator  
Indicates the power-on status, as follows:  
Solid green:  
Power is ON  
AUTO-SIZING button  
Flashing green: PowerManager Mode 1  
Advance Notice Mode  
Automatically centers the  
displayed image, bringing  
the image borders into  
alignment with the  
Yellow:  
PowerManager Mode 2  
Flashing Yellow: Off Timer Mode  
monitor frame.  
Power switch  
QuickSetControl pad  
(hereinafter “Control pad”)  
Power terminal covers for the  
optional i·Sound sound unit  
Rear  
D-Sub mini 15 pin input connector  
Power connector  
Package Contents:  
EIZO Utility  
Disk  
Power Cord  
Warranty  
Registration  
Card  
User’s Manual  
Signal Cable  
(MD-C87)  
• If any of the above-listed items are missing or damaged, please contact your local  
dealer for assistance.  
INTRODUCTION  
7
1 INSTALLATION  
Connecting the monitor to the PC  
1)Be sure that the power switches of both the PC and the monitor are OFF.  
2)Plug the signal cable into the connector at the rear of the monitor.  
• When connecting the signal cable or cable adapter, first check that the shape at the  
cable side matches the shape at the connecting side. After connecting, secure the  
connection with the screw-in fasteners.  
3)Plug the other end of the cable into the video connector on the rear of the PC. Refer  
to the figures below.  
Standard PC graphics board  
D-Sub  
mini 15 pin  
D-Sub  
mini 15 pin  
Standard PC graphics board  
MD-C87 (enclosed)  
Using the monitor with Windows 95/98  
A monitor information file is in the EIZO utility disk enclosed with the package. It  
includes all the required information for best operation with Windows 95/98.  
Install the enclosed utility and select your model name from the monitor list in  
Windows 95/98. For installation procedure, read the Readme file in the utilily disk.  
Macintosh  
An optional Macintosh adapter must be connected to the PC before connecting the  
signal cable. Please consult EIZO dealer.  
D-Sub 15 pin  
D-Sub  
mini 15 pin  
D-Sub  
mini 15 pin  
Macintosh  
MD-C87 (enclosed)  
Macintosh Adapter (Optional)  
4)Plug the power cord into the power connector at the rear of the monitor. Then plug  
the other end of the cord into a power outlet.  
5)Turn on the monitor first, then the PC . The monitors power indicator will light up  
(green). The monitor will warm up briefly, then display an image. Whenever  
finishing your operation, turn off the PC and the monitor.  
• If an image does not appear, refer to the “TROUBLESHOOTINGsection on page  
15 for an advice.  
1
INSTALLATION  
8
Using the AUTO-SIZING button  
After connecting the monitor to the  
PC, first press the AUTO-SIZING  
button on the front panel. The  
AUTO-SIZING function centers the  
displayed image, aligning the  
images borders with respect to the  
monitor frame.  
E
In general, press the AUTO-SIZING button whenever changing the graphics board  
ro the resolution or when image size and/or position is incorrect.  
If further adjustment is required, adjust the picture size/position as desired using the  
Size/Position function in the ScreenManager. Refer to page 11.  
• Some signals from the graphics board may not function properly.  
• A solid-color screen (i.e. red, green, blue) may appear for an instant while  
performing the AUTO-SIZING function, while this phenomenon is not a failure.  
Setting the resolution  
The following look-up table shows the maximum (Non-interlaced) vertical refresh  
rates for this model with regard to standard resolutions set forth by VESA. The best  
way to see if the monitor will work with a given resolution and rate, is to compare the  
vertical refresh rate of the graphics board to the monitors range (Refer to the graphics  
board manual for specifications). If the refresh rate is within the specified range of  
the monitor, it should operate properly.  
Maximum Vertical Refresh rate (Hz)  
Horizontal Scan  
Frequency (kHz)  
640x480  
160  
800x600  
123  
1024x768  
101  
1280x1024  
76  
30-82  
What is Resolution?  
Resolution is expressed as the number of dots (pixels) displayed on the screen. A  
larger number of dots produces a more sharply defined (a higher-resolution) image.  
Note that for a given screen size the dot size decreases as the number of dots  
increases: a 640 × 480 (dot × line) resolution uses larger pixels than a 1024 × 768  
resolution. The display size of a given font therefore varies according to the  
resolution. Higher resolutions allow you to display more information on the screen.  
1
INSTALLATION  
9
2 SCREEN ADJUSTMENT  
How to use the ScreenManager  
Entering the ScreenManager  
Press the ENTER key to display the ScreenManager Main menu.  
Main menu  
Making the Adjustments and Settings  
1)Select the desired icon using the Arrow keys, and then press the ENTER key to  
display the each adjustment/setting menu.  
Adjustment menu  
2)Use the Control pad (the four Arrow keys and the ENTER key) to make the  
required adjustments and settings.  
Save & Exit  
1)To save settings and return to the Main menu, press the ENTER key.  
2)To exit the ScreenManager, select the Exit icon (or push the down Arrow key twice)  
and press the ENTER key.  
Adjustments and Settings  
Allow the monitor to stabilize for at least 30 minutes before making image  
adjustments.  
Function (Arrow Keys Used)  
OSD  
Adjusts: a) Contrast (left/right)  
b) Brightness (up/down)  
Contrast/  
Brightness  
· When a white text against a black  
background (e.g., DOS text) is used, setting  
the brightness at its maximum is  
recommended because a dark setting will  
result in eye strain due to high character  
contrast.  
2
SCREEN ADJUSTMENT  
10  
Function (Arrow Keys Used)  
OSD  
E
Adjusts: Horizontal image size (left/right)  
Vertical image size (up/down)  
Size  
Adjusts: Screen position  
Position  
Adjusts: Side-pin balance (left/right)  
Side-pincushion (up/down)  
Side-  
Pin Balance/  
Side-  
Pincushion  
·Tilts:  
image sides to sides (left/right)  
Parallelogram/  
Trapezoidal  
·Expands: top side/bottom side, shirnking the  
other side (up/down)  
Tilts:  
the image (left/right)  
Tilt  
Adjusts: Horizontal convergence (left/right)  
Vertical convergence (up/down)  
Convergence  
· The convergence adjustment adjusts the  
entire screen. It is not possible to limit  
adjustment to specific screen areas.  
What is convergence?  
Convergence is the monitors ability to precisely  
illuminate specific phosphors and line them up  
properly in order to produce pure color.  
Moiré  
Adjusts horizontal moiré (left/right)  
What is moiré?  
Moiré refers to an interference pattern of  
dark wavy lines on the screen. It is not a  
defect, but rather an interference  
phenomenon caused by the relationship  
between the phosphor layout and the  
imaging signal. Moiré is often an indication  
of a good focus level. Moiré is particularly  
noticeable when using a light-gray or every-  
other-dot pattern background. Although  
moiré can not be eliminated, it can be  
reduced with the moiré reduction feature.  
2
SCREEN ADJUSTMENT  
11  
Function (arrow keys usd)  
OSD  
Color  
Adjusts: Color temperature  
Temperature can be set from 6,500 K to  
10,000 K, in 500 K increments.  
· Each monitor is slightly different, if two  
monitors are set to the same color  
temperature value (i.e. 6,500K), they  
may not necessarily look the same.  
PowerManager  
Reset  
· VESA DPMS  
· Off Timer  
(Refer to the text below)  
Default settings are as follows.  
· Contrast/Brightness:100%/50%  
· Moiré:  
· Color:  
0%  
9,300K  
· PowerManager:  
VESA DPMS = On  
Off Timer = Disable  
PowerManager (VESA DPMS, OffTimer)  
What is PowerManager?  
The PowerManager feature automatically reduces the monitors power  
consumption during idle periods. The EIZO PowerManager functions comply  
with the VESA DPMS standard.  
As an ENERGY STAR® Partner, EIZO NANAO CORPORATION has determined that this  
product meets the ENERGY STAR® guidelines for energy efficiency.  
• Do your part to conserve energy, turn off the monitor when your finished using  
it. Complete energy use can only be stopped by disconnecting the monitor  
from the power supply.  
• When the monitor is in a power saving mode, the optional EIZO i·Sound  
speaker unit and the optional EIZO i·Station USB hub will turn off.  
• Off Timer will work while PowerManager is active, but there will be no advance  
notice before the monitor's power switches off.  
VESA DPMS  
What is VESA DPMS?  
The acronym VESA stands for “Video Electronics Standards Association,”  
and DPMS stands for “Display Power Management Signaling.” DPMS is a  
communication standard that PCs and graphics boards use to implement  
power savings at the monitor side.  
2
SCREEN ADJUSTMENT  
12  
Set-up Procedure  
1)First, make the appropriate settings for the PC.  
2)Select VESA DPMS icon in the ScreenManagers PowerManager menu.  
3)Select On”.  
E
Power saving method of VESA DPMS and the monitor  
VESA DPMS utilizes four signals: ON, STAND-BY, SUSPEND, and OFF. The  
monitor detects these signals from the graphics board and executes power-saving  
accordingly, as shown in the table below.  
Signal  
ON  
Screen  
Operation  
LED  
Green  
Power consumption  
110 W (normal)  
80% of normal  
less than 10 W  
less than 3 W  
STAND-BY  
SUSPEND  
OFF  
Blank  
Green  
Blank (Mode 1)  
Blank (Mode 2)  
Flashing green  
Yellow  
Off Timer  
What is Off Timer?  
The Off Timer function allows the user to set the time in which the monitor  
will be in operation, called the “On Period” and automatically shifts the  
operation into the “Off Timer Mode” when the set “On Period” expires. The  
energy consumption of the monitor in the “Off Timer Mode” is as low as the  
one of the monitor in “PowerManger Mode 2” although no setting PC to  
operate the Off Timer function is required.  
Set-up Procedure  
(1)Select the Off Timer” icon.  
(2)Select Enable”.  
(3)Press the right/left key to adjust how long (1 to 23 hours) the monitor should  
be in the “On Period”.  
Advance notice (LED flashing green) will be given 15 minutes before the monitor  
automatically enters the “Off Timer Mode”.  
To Delay Entering the “Off Timer Mode”  
To delay entering the “Off Timer Mode”, press any keys on the front panel  
located to the left of the power switch during the “Advance notice Mode”. The  
monitor will continue to operate for an additional 90 minutes. There will be  
another advance notice for 15 minutes as described. Delayed entrance into the  
“Off Timer Mode” can be extended as many times as desired.  
2
SCREEN ADJUSTMENT  
13  
What is ENERGY STAR?  
ENERGY STAR” is a set of power saving guidelines issued by the U.S.  
Environmental Protection Agency (EPA). The guidelines apply to PC systems and  
peripherals.  
Shortcut Keys  
Before entering the ScreenManager, brightness and contrast can be adjusted directly  
by moving the Control pad. To record the new setting and exit the ScreenManager,  
press the Enter key. (The brightness and contrast functions are also available in the  
ScreenManager “contrast/brightness” menu.)  
Brightness Up  
Contrast  
Down  
Contrast  
Up  
Brightness Down  
Adjustment Lock  
The ScreenManager operation can be disabled by holding down the AUTO-SIZING  
button while switching on the monitors power. This will disable (“lock”) the  
ScreenManager and AUTO-SIZING button, protecting from accidental changes. To  
unlock the buttons: switch the power off, then hold down AUTO-SIZING button  
once again and turn the power back on.  
Note that brightness and contrast can be adjusted using the shortcut keys even  
while the Control pad is locked. After making such an adjustment, push the  
ENTER key to clear the brightness/contrast adjustment menu from the screen.  
2
SCREEN ADJUSTMENT  
14  
3 TROUBLESHOOTING  
Troubleshooting  
If a problem persists even after applying the suggested remedies, contact an  
EIZO dealer.  
E
Problems  
Points to check with possible solutions  
1) Indicator status: OFF  
Check that the power cord is correctly connected.  
2) Indicator status: GREEN  
Try pressing a key on the keyboard, or clicking the  
mouse. (The monitor may be in a power saving mode.)  
Check brightness and contrast settings. Minimum  
settings will cause screen to be blank.  
Try pressing a key on the keyboard, or clicking the  
mouse. (The monitor may be in a power saving mode.)  
3) Indicator status: YELLOW  
Try pressing any keys on the front panel, or switch the  
monitor off and then on. (The monitor may be in “Off  
Timer Mode”.)  
4) Indicator status: YELLOW  
(flashing)  
If the problem persists, switch off the monitor power for a  
few minutes, then switch it back on and try again.  
5) Following message appears.  
Check that the PC is switched ON.  
Check that the signal cable is properly connected to the  
graphics board or PC.  
Check that the graphics board is correctly inserted in  
the PC.  
6) Following message appears.  
(Example)  
Use the graphics boards utility software to change the  
frequency setting. (Refer to the manual of the graphics  
board.)  
Whenever an error signal message appears, the signal frequency will be displayed in red.  
Error messages shown above will remain on the screen for 30 seconds. An error message  
may not appear at all if the signal frequency is extremely high or extremely low.  
Use of the “Moiré” adjustment may cause a slight  
vibration. To eliminate the vibration, set the adjust-  
ment level to lower percentage or 0% . See page 11.  
7) The image vibrates on the  
screen.  
Check that the signal cable is properly connected to the  
graphics board or PC.  
Check that the graphics board is correctly mounted in  
the PC.  
3
TROUBLESHOOTING  
15  
Problems  
Points to check with possible solutions  
The monitor may be located close to a device that is  
generating a magnetic field. Such devices include  
speakers (other than the EIZO optional i·Sound  
speaker), electric motors, high-voltage cables, and other  
monitors. It may be solved by switching off or moving  
the interfering device, or by relocating the monitor.  
If the volume level of the EIZO optional i·Sound  
speaker is too high, it may, in some cases, cause a slight  
vibration. To eliminate, turn down the volume of the  
speaker.  
An unstable signal from the graphics board may be the cause of the above problem when  
using the monitor with a high resolution or in a high refresh mode. (The video signal from  
the graphics board might be made irregular due to the use of a high speed dot clock.)  
Change the resolution or the refresh rate to another setting.  
Reduce the moiré using the ScreenManagers Moiré”  
adjustment menu following the procedure below.  
8)Moiré patterns are  
distracting.  
1) Set the desktop to an every-other-dot pattern so that  
moiré will be visible.  
2) Go to the ScreenManagers Moiré” menu and adjust  
so that moiré becomes almost unnoticeable. See page 11.  
3) Change to a different desktop background to reduce  
moiré even further.  
Change the horizontal and vertical dimensions of the  
desplay area.  
Change the selected desktop or wallpaper pattern to any  
solid color pattern. For detailed information on how to  
change these patterns, refer to the documentation for  
the PC and operating system.  
9) The image is flickering.  
Flicker will occur with interlaced scanning, or  
non-interlaced scanning with a low refresh rate. All  
EIZO monitors are capable of reproducing high refresh  
rates for non-interlaced scanning. If a problem occurs  
when using a non-interlaced signal, try adjusting the  
graphics board to increase the refresh rate (if possible).  
Refer to the graphics board manual for information.  
Flicker  
The term “flicker” refers to noticeable shimmering that occurs when the image on the  
screen is redrawn (“refreshed”) too slowly. A refresh rate of 80 Hz means the image is  
redrawn 80 times per second. Most people will notice flicker at image refresh rates as high  
as 60 or 70 Hz, whereas refresh rates of 72 Hz or above usually is not noticeable. Flicker  
is known to be the cause of visual fatigue.  
3
TROUBLESHOOTING  
16  
Problems  
Points to check with possible solutions  
10)• The entire screen appears  
bluish or reddish.  
The CRT is not warmed up. Allow 30 minutes for the  
monitor to stabilize.  
E
• Color purity is not  
uniform.  
Misconvergence of colors.  
(red, green, blue)  
Explanation of the Characteristics of CRTs  
When the monitor is not fully warmed up, the screen may look slightly colored, e.g.  
reddish or bluish. This phenomenon is due to the unstableness of the electron gun during  
its warm-up period. Please wait for about 30 minutes until the monitor stabilizes in order  
to gain its proper color.  
11)• Control Pad “ENTER  
key” does not operate.  
The Adjustment Lock is probably on. To unlock: switch  
off the monitor power, then hold down the AUTO-  
SIZING button and switch the monitor back on. See  
page 14.  
• AUTO-SIZING button  
does not operate.  
12)AUTO-SIZING button does  
not work properly.  
The AUTO-SIZING function is intended for use on the  
Macintosh and on IBM compatibles running Windows.  
It may not work properly if either of the following  
applies.  
- You are running an AT-compatible PC on  
MS-DOS (not Windows).  
- The background color for the “wallpaper” or  
“desktop” pattern is set to black.  
Some signals from graphics boards may not function  
properly.  
A solid-color screen (i.e. red, green, blue) may appear for an instant while performing the  
AUTO-SIZING function, althought, this phenomenon is not a failure.  
3
TROUBLESHOOTING  
17  
Problems  
Points to check with possible solutions  
13)Two horizontal hairlines are  
visible on the screen.  
These are dampening wires. Dampening wires are used  
to support the CRTs aperture grille, and are visible as  
thin dark lines across the screen. All EIZO aperture-  
grille type CRTs include two such  
horizontal wires.  
The aperture grille itself is a grid of taut metal filaments  
that spans the entire screen from top to bottom.  
The aperture grille may be misaligned. Shock or  
vibration during transport may, in some cases, cause the  
aperture grille to fall out of alignment. The problem  
will appear as one or more faint black lines across the  
screen.  
14)Faint black vertical lines are  
visible on the screen.  
If this problem occurs, it may be able to solved by:  
degaussing the screen, or  
lightly tapping (do not hit) the side of  
the monitor.  
If neither of these methods works, try executing the  
following procedure.  
1) Display a bright white field over the area where  
the black line(s) appear, with a black field over  
the unaffected areas. (Do this by opening a  
bright-white window on top of a black desktop  
or wallpaper background. Position the window  
so that it just covers the area of misalignment.)  
2) Set brightness and contrast to maximum values,  
and keep the display ON until the problem is  
corrected. Try tapping the side of the display  
lightly to help expedite realignment. The white  
field will heat up the misaligned area of the  
grille, returning it to proper alignment.  
3
TROUBLESHOOTING  
18  
4 CLEANING  
WARNING  
Keep liquids away from the monitor.  
E
Spillage into the cabinet may result in fire, electric shock, or equipment  
damage.  
If an object or liquid falls/spills into the cabinet, unplug the monitor  
immediately. Have the unit checked by a qualified service engineer  
before using it again.  
Using the monitor in this condition could cause serious injury or  
equipment damage.  
CAUTION  
To ensure safety, always unplug the monitor before cleaning it.  
Failure to do so may result in electric shock.  
Periodically clean the area around the plug.  
Buildup of dust, water, or oil on the plug may result in fire.  
Never use thinner, benzene, alcohol (ethanol, methanol, or  
isopropyl alcohol), abrasive cleaners, or other strong solvents, as  
these may cause damage to the cabinet or CRT.  
Periodic cleaning is recommended to keep the monitor looking new and  
to prolong its operational lifetime. Clean the cabinet and CRT areas as  
follows:  
Cabinet  
To remove stains, wipe the cabinet with a soft, lightly moistened cloth  
using a mild detergent. Do not spray wax or cleaner directly onto the  
cabinet.  
CRT Surface  
The CRT surface can be cleaned with a soft cloth, such as cotton or  
lens paper.  
If necessary, stubborn stains can be removed by moistening part of a  
cloth with water to enhance its cleaning power.  
4
CLEANING  
19  
5 SPECIFICATIONS  
Electrical Specifications  
CRT  
45 cm (17 inch) class, 90° deflection Aperture Grille type  
CRT with Anti-Reflective SuperErgoCoat®  
0.25 mm  
CRT AG Pitch  
Scan Frequency  
Horizontal:  
Vertical:  
30 kHz-82 kHz (Automatic)  
50 Hz-160 Hz (Automatic)  
Max. Active Display Area 323 mm (H) × 242 mm (V)  
(12.7” (H) × 9.5” (V))  
(Viewable image size: 403 mm (15.8”))  
* Display size can be set by the user through  
microprocessor control panel.  
* The actual size displayed can be dependent on the  
graphics board or PC utilized.  
Power Supply  
Power Consumption  
Normal:  
100-120/220-240 VAC±10% , 50/60 Hz, 1.3/0.6 A  
110 W  
Max.:  
135 W (with EIZO optional speaker attached)  
PowerManager Mode 1: Less than 10 W  
PowerManager Mode 2: Less than 3 W  
Input Connector  
D-Sub mini 15-pin  
Recommended Resolution 1024 dots × 768 lines  
Input Signal  
Sync:  
H/V Separate, TTL, Positive/Negative  
H/V Composite, TTL, Positive/Negative  
• Sync on Green 0.3 Vp-p, Negative  
• Analog 0.7 Vp-p/75 , Positive  
VESA DDC1/2B  
Video:  
Plug & Play  
Mechanical Specifications  
Dimensions  
410 mm (W) × 413 mm (H) × 439 mm (D)  
(16.1” (W) × 16.3” (H) × 17.3” (D))  
20.8 kg (45.8 lbs.)  
Weight  
Environmental Specifications  
Temperature  
operating: 0°C to 35°C (32°F to 95°F)  
storage: -20°C to 60°C (-4°F to 140°F)  
30% to 80% R.H. Non-condensing  
Humidity  
20  
5
SPECIFICATIONS  
PresetTiming  
E
2 factory presets shown below have been registered in the monitors  
microprocessor.  
Resolution  
Frequencies  
Interlace Sync Polarity Video Signal  
Level  
fH (kHz) fV (Hz)  
VGA  
(text)  
720 × 400  
31.47  
70.09  
Non  
H/Negative 0.7V(p-p)/75  
V/Positive  
VESA 1024 × 768 68.68  
85.00  
Non  
H/Positive  
V/Positive  
0.7V(p-p)/75Ω  
Pin Assignment  
D-Sub mini 15 pin connector  
Pin No.  
1
Signal  
Pin No.  
Signal  
Red video  
9
No pin  
Green video/  
Green video/  
Green video with  
10  
Ground  
Ground  
(shorted)  
(shorted)  
2
11  
12  
composite sync  
composite sync  
Data  
3
4
5
6
7
8
Blue video  
Ground  
H. Sync/  
H. Sync/  
H/V composite  
13  
sync  
No pin  
sync  
Red ground  
Green ground  
Blue ground  
14  
15  
V. Sync  
Clock  
Dimensions  
mm  
(inches)  
302.1  
(11.9)  
410  
(16.1)  
323  
(12.7)  
242  
413  
(9.5)  
(16.3)  
74.9 122  
(2.9) 4.8  
46.9  
(1.8)  
439  
(17.3)  
ø265  
ø10.4)  
(
5
SPECIFICATIONS  
21  
LIMITED WARRANTY  
EIZO NANAO CORPORATION (“EIZO”) and EIZO’s authorized distributors warrant to the original purchaser that the product shall be  
free from defect in material and/or workmanship for a period of three (3) years from the date of purchase. The service parts stock for  
this model shall be maintained for 5 years after the production is discontinued. To ensure the warranty, EIZO highly suggests that  
you return your “Warranty Registration” card to EIZO.  
In the event of malfunction during the warranty period attributable directly to faulty material and/or workmanship, EIZO and EIZO’s  
authorizes distributors will, at their option, either repair or replace the faulty product with the same or similar model. EIZO and EIZO’s  
authorized distributors shall have no obligation under this warranty, however, in the following cases:  
(a) Any defect caused by freight damage, modification, alteration, abuse, misuse, accident, incorrect installation, disaster, faulty  
maintenance or improper repair by third party other than EIZO and EIZO’s authorizes distributors.  
(b) Any deformation, discoloration, warping, losing brightness or focus, or whatsoever due to normal deterioration of the product.  
(c) Any incompatibility of the products with subsequent technical innovations or regulations.  
(d) Any defects that are caused by burning of the screen phosphor, scratches on the surface and/or the blistering, peeling or  
flaking of the coating/panel on the CRT tube itself.  
(e) Any defect of the product caused by external equipment.  
(f)  
Any defect of the product on which the original serial number has been altered or removed.  
To obtain service under this warranty, the original purchaser must deliver the product, freight prepaid, in its original package or other  
adequate package affording an equal degree of protection, assuming the risk of damage and/or loss in transit, to your local EIZO  
authorized distributor. The original purchaser must present proof of purchase establishing proof and date of purchase of the  
product when requesting warranty service.  
Once the warranty period has expired, the warranty on any replaced and/or repaired part also expires.  
EIZO AND EIZO’S AUTHORIZED DISTRIBUTORS MAKE NO FURTHER WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT  
TO THE PRODUCT AND ITS QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR USE. IN  
NO EVENT SHALL EIZO AND EIZO’S AUTHORIZES DISTRIBUTORS BE LIABLE FOR ANY SPECIAL, CONSEQUENTIAL,  
INCIDENTAL OR OTHERS DAMAGES (INCLUDING, WITHOUT LIMITATION, LOSS OR PROFIT) WHETHER OR NOT EIZO AND  
EIZO’S AUTHORIZED DISTRIBUTORS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, ARISING OUT OF  
ANY BREACH OR REPUDIATION OF CONTRACT, OR WARRANTY, NEGLIGENCE, OR OTHERWISE. THIS EXCLUSION ALSO  
INCLUDES ANY LIABILITY WHICH MAY ARISE OUR OF THIRD PARTY CLAIMS AGAINST THE ORIGINAL PURCHASER. THE  
ESSENCE OF THE PROVISION IS TO LIMIT THE POTENTIAL LIABILITY OF EIZO AND EIZO’S AUTHORIZES DISTRIBUTORS  
ARISING OUT OF THIS AGREEMENT AND/OR SALES.  
GARANTIE LIMITEE  
EIZO NANAO CORPORATION (EIZO) et ses distributeurs agréés donnent à l’acquéreur une garantie couvrant les défauts matériels  
et/ou de fabrication pendant trois ans à compter de la date d’acquisition. Pour bénéficier de la garantie de trois (3) ans veuillez  
renvoyer la carte d'enregistrement à EIZO CORPORATION. Un stock de pièces détachées devra être maintenu dans les 5  
années suivant la fin de vie de ce produit.  
Dans l’éventualité d’un défaut de fonctionnement, pendant la période de garantie, attribué directement à un défaut matériel et/ou de  
fabrication, EIZO et ses distributeurs agréés, selon leur choix, répareront ou remplaceront le produit défectueux par un modèle  
identique ou similaire. EIZO et ses distributeurs agréés, d’après cette garantie, n’ont aucune obligation dans les cas suivants:  
(a) Tous défauts causés par un transport sans précautions, par des modifications, par des changements, par une mauvaise  
utilisation, par un accident, par une installation incorrecte, par un désastre, par un entretien défectueux ou une mauvaise  
réparation par un tiers autre qu'EIZO et ses distributeurs.  
(b) Toutes déformations, décolorations, perte de luminosité ou de mise au point, ou tout autre défaut dû à la détérioration  
normale du produit.  
(c) Toutes incompatibilités des produits avec des innovations ou règlements techniques ultérieurs.  
(d) Tous défauts causés par une brûlure du phosphore de l’écran, par des éraflures, par des décollements, par des écaillements  
et/ou des boursouflures de la couche du panneau arrière du tube CRT.  
(e) Tous défauts du produit causés par des équipements externes.  
(f) Tous défauts du produit sur lequel le numéro de série originel a été retiré ou modifié.  
Pour profiter de cette garantie, l’acheteur originel doit retourner le produit (en port payé) à son distributeur EIZO agréé, dans son  
emballage d’origine ou dans un autre emballage offrant un degré de protection équivalent, et en prenant la responsabilité en cas de  
détériorations et/ou de perte pendant le transport. Dans le cas de l’utilisation de la garantie, l’acheteur originel doit présenter  
un document prouvant l’achat ainsi que la date d’achat.  
Après l’expiration de la période de garantie, cette dernière expire aussi sur les pièces réparèes et/ou remplacées.  
EIZO ET SES DISTRIBUTEURS AGREES, NE FOURNISSENT AUCUNE AUTRE GARANTIE, EXPRIMEE OU INSINUEE, EN CE  
QUI CONCERNE LE PRODUIT ET SA QUALITE, SES PERFORMANCES, SA COMMERCIALISATION OU SON APTITUDE EN  
CAS D’UTILISATIONS PARTICULIERES. EN AUCUN CAS, EIZO ET SES DISTRIBUTEURS AGREES NE SONT RESPONSABLES  
DES DOMMAGES CONSECUTIFS, D’IMPORTANCE SECONDAIRE ET DETOUT AUTRE SORTE (INCLUANT AUCUNE LIMITATION  
DE PERTES OU DE PROFITS), QU’EIZO ET SES DISTRIBUTEURS AGREES AIENT ETE AVISES DE LA POSSIBILITE DETELS  
DEGATS, PROVENANT DE LA VIOLATION OU DU REFUS DU CONTRAT OU DE LA GARANTIE, DE NEGLIGENCES OU DANS  
TOUT AUTRE CAS, CES RESTRICTIONS S’APPLIQUENT EGALEMENT EN CAS DE RECLAMATION D’UN TIERS CONTRE  
LACHETEUR ORIGINEL, LE BUT DE CES PROVISIONS EST DE LIMITER LA RESPONSABILITE D’EIZO ET DE SES  
DISTRIBUTEURS AGREES DANS LE CADRE DE CET ACCORD ET/OU DE CES VENTTES.  
GARANTIE  
EIZO NANAOCorporation (EIZO) und die autorisierten Distributoren garantieren dem Erstkäufer für drei (3) Jahre ab  
Kaufdatum, daß das von ihnen gelieferte Produkt frei von Material- und Verarbeitungsfehlern ist. Ersatzteile für dieses  
Modell werden für fünf (5) Jahre nach Produktionsende lieferbar sein. Um die Garantie zu gewährleisten, empfiehlt EIZO  
die Rücksendung der „Warranty Registration Card“ an EIZO.  
Im Fall einer Fehlfunktion innerhalb dieser Garantiezeit, die direkt auf Material- und Verarbeitungsfehler zurückzuführen ist,  
werden EIZO bzw. die autorisierten Distributoren, nach freier Wahl, das defekte Produkt entweder reparieren oder durch ein  
gleiches oder gleichwertiges ersetzen. EIZO bzw. den Distributoren entsteht in folgenden Fällen jedoch keine Verpflichtung  
aus dieser Garantie:  
(a) bei jeglichen Transportschäden, Modifizierungen, Änderungen, Mißbrauch, nicht bestimmungsgemäßer Nutzung,  
Unglücksfällen, fehlerhafter Installation, fehlerhafter Wartung oder nicht sachgemäßer Reparatur durch Dritte außer  
EIZO oder deren autorisierten Distributoren.  
(b) bei jeglicher Verformung, Farbveränderung, Helligkeits- oder Schärfeverlust, oder sonstige Mängel, die durch  
normale Abnutzung bedingt sind.  
(c) bei jeglicher Inkompatibilität der Produkte mit künftigen technischen Neuerungen und Regelungen.  
(d) bei jeglichen Defekten, die durch Einbrennen des Phosphors entstehen, Kratzer oder Bläschen auf der  
Bildschirmoberfläche, Ablösung der Oberflächenbeschichtung der Bildröhre selbst.  
(e) bei jeglichem Defekt, der auf externes Equipment zurückzuführen ist.  
(f) bei jeglichem Defekt des Produktes, bei dem die Originalseriennummer verändert oder entfernt wurde.  
Im Garantiefall muß das Produkt in Original- oder gleichwertiger Verpackung, die denselben Schutz bietet, an Ihren  
autorisierten EIZO-Distributor frei zurückgeschickt werden, wobei der Käufer das Risiko für Verlust oder Beschädigung trägt.  
Garantieleistungen können nur unter Nachweis des Kaufbeleges durch den Käufer in Anspruch genommen werden.  
Die 3 jährige Garantiedauer verlängert sich durch Austausch und/oder Reparatur von Teilen nicht.  
EIZO und die autorisierten Distributoren übernehmen keine weitergehende Garantie, weder ausdrücklich noch eingeschlossen, in  
Hinsicht auf das Produkt und seine Qualität, auf Leistungsmerkmale, auf Vermarktungsfähigkeit oder seine Eignung für spezielle  
Anwendungen. In keinem Fall haftet EIZO bzw. die Distributoren für besondere, zufällige, Folge- oder andere Schäden (einschl.  
entgangenem Gewinn) gleichgültig, ob Sie auf die Möglichkeit eines solchen Schadens, der aus Verstoß oder Verletzung vonVertrags-  
oder Garantiebestimmungen, sowie Fahrlässigkeit oder ähnlichem entstehen kann, hingewiesen wurden. Ausgeschlossen ist auch  
jedeVerantwortung, die aus möglichen Ansprüchen Dritter gegen den Erstkäufer entstehen kann. Die Absicht dieser Bestimmung ist  
die Einschränkung der eventuellen Haftung EIZOs oder der autorisierten Distributoren, die aus dieser Vereinbarung und/oder dem  
Kauf entstehen könnte.  
GARANTIA LIMITADA  
EIZO NANAO CORPORATION (“EIZO”) y los distribuidores autorizados de EIZO garantizan al comprador original que el  
producto estará libre de defectos en material y/o mano de obra por un periodo de tres (3) años desde la fecha de compra. El  
stock de piezas de repuesto será mantenido durante cinco años desde que acabe la producción de este modelo. Para que la  
garantía sea válida, EIZO sugiere encarecidamente, que se envíe a EIZO la tarjeta de Registro de Garantía.  
En el caso de mal funcionamiento atribuible directamente a defectos de material y/o mano de obra durante el periodo de  
garantía, EIZO y sus distribuidores autorizados se reservan el derecho de reparar o reemplazar el producto defectuoso por el  
mismo o similar modelo. No obstante, EIZO y sus distribuidores autorizados no están obligados por esta garantía en los  
siguientes casos:  
(a) Cualquier defecto producido por daños en el transporte, modificación, alteración, abuso, maltrato, accidente, instalación  
incorrecta, desastre, mal mantenimiento o reparación por parte de cualquiera que no sea EIZO o alguno de sus  
distribuidores autorizados.  
(b) Cualquier deformación, decoloración, perdida debrillo o foco, o todo lo causad por eldeterioro normal del producto.  
(c) Cualquier incompatibilidad de los productos con reglamentaciones o innovaciones tecnológicas posteriores.  
(d) Cualquier defecto causado por el desgaste del fósforo de la pantalla, rayas en la superficie y/o la formación de burbujas,  
desconchamientos o peladuras del panel del propio tubo de rayos catódicos.  
(e) Cualquier defecto del producto producido por equipamiento externo.  
(f) Cualquier defecto del producto en el cual el número de serie original haya sido alterado o retirado.  
Para obtener la prestación del servicio bajo esta garantía, el comprador original debe devolver el producto al distribuidor  
autorizado de EIZO, con los gastos de envío pagados, en su embalaje original o en otro que ofrezca igual grado de protección  
y asumiendo el riesgo de daño y/o pérdida durante el envío. El comprador original debe presentar, cuando así se lo pida  
el servicio de garantías, una prueba con la fecha y el lugar de compra del producto.  
Una vez que el periodo de garantía finalice, también se da por terminada la garantía sobre cualquier parte reparada y/o  
sustituida.  
EIZO Y SUS DISTRIBUIDORES AUTORIZADOS NO CUBREN MAS GARANTIAS, EXPRESADAS O IMPLICITAS, CON  
RESPECTO AL PRODUCTO Y SU CALIDAD, PRESTACIONES, CAPACIDAD COMERCIAL O SALUD PARA CUALQUIER  
USO EN PARTICULAR. EN NINGUN CASO EIZO Y SUS DISTRIBUIDORES AUTORIZADOS SERAN RESPONSABLES DE  
CUALQUIER OTRO DAÑO (INCLUYENDO, SIN LIMITACION, PERDIDAS O BENEFICIOS) HAYAN O NO AVISADO EIZO Y  
SUS DISTRIBUIDORES AUTORIZADOS DE LA POSIBILIDAD DE TALES DAÑOS, COMO CONSECUENCIA DE CUALQUIER  
INCUMPLIMIENTO O RECHAZO DE CONTRATO, GARANTIA, NEGLIGENCIA U OTROS. ESTA EXCLUSION TAMBIEN  
INCLUYE CUALQUIER RESPONSABILIDAD QUE PUEDA SURGIR DE DEMANDAS DE TERCEROS CONTRA EL  
COMPRADOR ORIGINAL. LA ESENCIA DE ESTA DISPOSICION ES LIMITAR LA RESPONSABILIDAD POTENCIAL QUE  
PUEDA SURGIR A EIZO Y SUS DISTRIBUIDORES AUTORIZADOS DE ESTE ACUERDO Y/O VENTA.  
GARANZIA LIMITATA  
EIZO NANAO CORPORATION (in seguito denominata EIZO) e i distributori autorizzati EIZO garantiscono il prodotto per quanto  
riguarda sia i difetti di materiale sia i difetti di lavorazione per il periodo di anni tre (3) dalla data di acquisto. Il magazzino delle parti  
di ricambio per questo modello dovrà essere mantenuto per 5 anni dopo il termine della produzione. La scheda di registrazione  
del cliente, qui allegata, deve essere compilata e spedita entro dieci (10) giorni dalla data di acquisto.  
Nel caso in cui, nel periodo di garanzia, si verifichino dei malfunzionamenti imputabili ai materiali e/o alla manodopera, EIZO e i  
distributori autorizzati EIZO, potranno, a loro scelta, riparare o sostituire il prodotto difettoso con uno identico o analogo. EIZO e i  
distributori autorizzati EIZO non si assumono alcuna responsabilità nei seguenti casi:  
(a) Difetti causati da trasporto, modifiche, uso improprio, cause accidentali, installazione eseguita scorrettamente, manutenzione  
carente o tentativi di riparazione eseguiti da terzi che non siano EIZO e i distributori autorizzati EIZO.  
(b) Qualsiasi deformazione, scolorament, perdita di luminosità o funco, o qualsiasi altro tipo di alterazione dovuto al normale  
deteriorament del prodotto.  
(c) Qualsiasi incompatibilità del prodotto con standard industriali introdotti successivamente.  
(d) Qualsiasi difetto relativo alla bruciatura dei fosfori dello schermo e al degrado del rivestimento interno del tubo catodico.  
(e) Qualsiasi difetto derivante dall’uso di dispositivi esterni al prodotto.  
(f) Qualsiasi difetto di qualsiasi origine se il numero di serie del prodotto è stato alterato o cancellato.  
Per usufruire del servizio di assistenza nei termini di questa garanzia, il cliente deve far pervenire il prodotto, franco di porto,  
nell’imballo originale o in imballo analogo che garantisca lo stesso grado di protezione, a EIZO o a un distributore autorizzato  
EIZO. Il cliente originale deve presentare un documento di prova che dimostri inequivocabilmente la data di acquisto  
del prodotto.  
Quando la garanzia del monitor termina, anche la garanzia sulle parti sostituite o riparate termina.  
EIZO E I DISTRIBUTORI AUTORIZZATI EIZO NON RILASCIANO ALCUNA GARANZIA, IMPLICITA O ESPLICITA,  
RELATIVAMENTE AL PRODOTTO E ALLA SUA QUALITÀ, ALLE SUE PRESTAZIONI, ALLA SUA VENDIBILITÀ E AL SUO  
IMPIEGO PER SCOPI PARTICOLARI. IN NESSUN CASO EIZO E I DISTRIBUTORI AUTORIZZATI EIZO POSSONO ESSERE  
RITENUTI RESPONSABILI DI QUALSIASI DANNO, DIRETTO O INDIRETTO (IVI COMPRESI QUELLI CONCERNENTI LA PERDITA  
DI PROFITTI, LINTERRUZIONE DELLATTIVITÀ E SIMILI) DERIVANTI DALLIMPIEGO E DALLIMPOSSIBILITÀ DI USO DI  
PRODOTTI EIZO ANCHE SE EIZO È STATA AVVERTITA DELLA POSSIBILITÀ DI TALI DANNI. QUESTA ESCLUSIONE DI  
RESPONSABILITÀ RIGUARDA ANCHE I RISARCIMENTI CHE TERZI POSSONO RECLAMARE NEI CONFRONTI  
DELLACQUIRENTE. QUESTA NOTA VUOLE LIMITARE LA RESPONSABILITÀ DI EIZO E DEI DISTRIBUTORI AUTORIZZATI  
EIZO AL CONTENUTO DELLACCORDO DI VENDITA.  
GARANTIVILLKOR  
EIZO NANAO CORPORATION (”EIZO”) och EIZOs auktoriserade distributörer garanterar ursprungskunden att produkten skall  
vara fri från materialfel och/eller tillverkningsfel under tre (3) år från inköpsdatum. Reservdelar för denna modell kommer att  
lagerhållas under 5 år efter att produktionen upphört. Vi rekommenderar att Ni skickar in det bifogade registreringskortet  
till oss för att registrering av korrekt inköpsdatum skall kunna ske.  
Om det skulle uppstå något fel på produkten under garantitiden som kan relateras till materialfel eller tillverkningsfel förbinder  
EIZO och EIZOs distributörer sig att avhjälpa felet eller byta ut den felaktiga produkten (EIZO eller distributören bestämmer  
vilket) mot samma eller likvärdig modell. EIZO och EIZOs distributörer tar dock inte något ansvar för fel som uppstått under  
någon eller några av följande omständigheter:  
(a) Skador uppkomna vid frakt, olycka, katastrof, åverkan, modifiering, felaktig installation, felaktigt användande, bristfälligt  
underhåll eller felaktig reparation utförd av annan än EIZO alternativt EIZOs auktoriserade distributör.  
(b) Bilddeformation, färgfel, vitjämnhetsfel, avtagande ljusstyrka, försämrad skärpa och andra bildfel som beror på normal  
förslitning.  
(c) Inkompatibilitet som uppstått på grund av teknisk utveckling.  
(d) Defekter som uppkommit på grund av fosforbränning, repor på ytan och/eller övriga skador på ytbehandlingen/glaspanelen  
på bildröret.  
(e) Defekter som orsakats av extern utrustning.  
(f) Defekter på produkter där serienumret har ändrats eller tagits bort.  
För att få garantiservice måste ursprungskunden leverera produkten med betald frakt till EIZOs lokala distributör. Produkten  
skall vara packad i originalförpackning, eller lämpligt förpackad med hänsyn till risken för transportskador. Ursprungskunden  
skall kunna visa när produkten köpts med kvitto/faktura från inköpsstället för att garantin skall gälla.  
När garantiperioden har gått ut, upphör även garantin på utbytta/reparerade delar.  
EIZO OCH EIZOs AUKTORISERADE DISTRIBUTÖRER UTFÄSTER INGA YTTERLIGARE GARANTIER, KLART UTTRYCK  
ELLER UNDERFÖRSTÅTT, MED AVSEENDE PÅ PRODUKTEN OCH DESS KVALITET, PRESTANDA, SÄLJBARHET ELLER  
LÄMPLIGHET FÖR SPECIELLA ANVÄNDNINGSOMRÅDEN.INTE I NÅGOT FALL KAN EIZO ELLER EIZOs AUKTORISERADE  
DISTRIBUTÖRER STÄLLAS ANSVARIGA FÖR EVENTUELLA FEL, SKADOR, FÖLJDFEL (INKLUDERAR ÄVEN, UTAN  
BEGRÄNSNING, FÖRLORAD INKOMST ELLER AFFÄRSVINST) OAVSETT OM EIZO ELLER EIZOs AUKTORISERADE  
DISTRIBUTÖRER UNDERRÄTTATS OM MÖJLIGHETEN AV SÅDANA SKADOR BEROENDE PÅ BROTT AV ELLER  
FÖRNEKANDE AV AVTAL ELLER GARANTI, FÖRSUMMELSE ELLER ANNAT.DETTA UNDANTAG INNEFATTAR ÄVEN ALLT  
ANSVAR TILL FÖLJD AV KRAV FRÅN TREDJE MAN RIKTADE MOT URSPRUNGSKUNDEN. DESSA VILLKOR SYFTAR  
VÄSENTLIGEN TILL ATT BEGRÄNSA DET ANSVAR FÖR EIZO OCH EIZOs AUKTORISERADE ÅTERFÖRSÄLJARE SOM  
KAN UPPSTÅ TILL FÖLJD AV DENNA ÖVERENSKOMMELSE OCH/ELLER FÖRSÄLJNING.  
Congratulations!  
You have just purchased a TCO99 approved and labelled product! Your choice has provided you  
with a product developed for professional use. Your purchase has also contributed to reducing the  
burden on the environment and also to the further development of environmentally adapted  
electronics products.  
Why do we have environmentally labelled computers?  
In many countries, environmental labelling has become an established method for encourag-  
ing the adaptation of goods and services to the environment. The main problem, as far as  
computers and other electronics equipment are concerned, is that environmentally harmful  
substances are used both in the products and during their manufacture. Since it is not so far  
possible to satisfactorily recycle the majority of electronics equipment, most of these potentially  
damaging substances sooner or later enter nature.  
There are also other characteristics of a computer, such as energy consumption levels, that are  
important from the viewpoints of both the work (internal) and natural (external) environments.  
Since all methods of electricity generation have a negative effect on the environment (e.g. acidic  
and climate-influencing emissions, radioactive waste), it is vital to save energy. Electronics  
equipment in offices is often left running continuously and thereby consumes a lot of energy.  
What does labelling involve?  
This product meets the requirements for the TCO99 scheme which provides for international  
and environmental labelling of personal computers. The labelling scheme was developed as a  
joint effort by the TCO (The Swedish Confederation of Professional Employees), Svenska  
Naturskyddsforeningen (The Swedish Society for Nature Conservation) and Statens  
Energimyndighet (The Swedish National Energy Administration).  
Approval requirements cover a wide range of issues: environment, ergonomics, usability,  
emission of electric and magnetic fields, energy consumption and electrical and fire safety.  
The environmental demands impose restrictions on the presence and use of heavy metals,  
brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among  
other things. The product must be prepared for recycling and the manufacturer is obliged to  
have an environmental policy which must be adhered to in each country where the company  
implements its operational policy.  
The energy requirements include a demand that the computer and/or display, after a certain  
period of inactivity, shall reduce its power consumption to a lower level in one or more stages.  
The length of time to reactivate the computer shall be reasonable for the user.  
Labelled products must meet strict environmental demands, for example, in respect of the  
reduction of electric and magnetic fields, physical and visual ergonomics and good usability.  
Below you will find a brief summary of the environmental requirements met by this product.  
The complete environmental criteria document may be ordered from:  
TCO Development  
SE-114 94 Stockholm, Sweden  
Fax: +46 8 782 92 07  
Email (Internet): development@tco.se  
Current information regarding TCO99 approved and labelled products may also be  
Environmental requirements  
Flame retardants  
Flame retardants are present in printed circuit boards, cables, wires, casings and housings.  
Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a  
computer casing can consist of flame retardant substances. Most flame retardants contain  
bromine or chloride, and those flame retardants are chemically related to another group of  
environmental toxins, PCBs. Both the flame retardants containing bromine or chloride and the  
PCBs are suspected of giving rise to severe health effects, including reproductive damage in fish-  
eating birds and mammals, due to the bio-accumulative* processes. Flame retardants have been  
found in human blood and researchers fear that disturbances in foetus development may occur.  
The relevant TCO99 demand requires that plastic components weighing more than 25 grams  
must not contain flame retardants with organically bound bromine or chlorine. Flame  
retardants are allowed in the printed circuit boards since no substitutes are available.  
Cadmium**  
Cadmium is present in rechargeable batteries and in the colour-generating layers of certain  
computer displays. Cadmium damages the nervous system and is toxic in high doses. The  
relevant TCO99 requirement states that batteries, the colour-generating layers of display  
screens and the electrical or electronics components must not contain any cadmium.  
Mercury**  
Mercury is sometimes found in batteries, relays and switches. It damages the nervous system  
and is toxic in high doses. The relevant TCO’99 requirement states that batteries may not  
contain any mercury. It also demands that mercury is not present in any of the electrical or  
electronics components associated with the labelled unit.  
CFCs (freons)  
The relevant TCO99 requirement states that neither CFCs nor HCFCs may be used during  
the manufacture and assembly of the product. CFCs (freons) are sometimes used for washing  
printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the  
stratosphere, causing increased reception on earth of ultraviolet light with e.g. increased risks of  
skin cancer (malignant melanoma) as a consequence.  
Lead**  
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the  
nervous system and in higher doses, causes lead poisoning. The relevant TCO’99 requirement  
permits the inclusion of lead since no replacement has yet been developed.  
For Europe, etc. (220-240 Vac) Only  
CE Marking  
Declaration of Conformity  
Kind of equipment/Type-designation:  
Monitor/T550  
is in compliance with:  
Council Directive 73/23/EEC  
Council Directive 89/336/EEC  
EN60950:1992+A1+A2+A3+A4+A11  
EN55022 (classB):1997 EN50082-1:1992  
EN61000-3-2:1995  
EN61000-3-3:1995  
Konformitätserklärung  
Geräteart/Gerätetyp :  
Monitor/T550  
den folgenden Normen oder Vorschriften entspricht:  
EU-Richtlinie 73/23/EEC  
EU-Richtlinie 89/336/EEC  
EN60950:1992+A1+A2+A3+A4+A11  
EN55022 (classB):1997 EN50082-1:1992  
EN61000-3-2:1995  
EN61000-3-3:1995  
Déclaration de conformité  
Nature de léquipement/Type-désignation : Moniteur/T550  
est en conformité avec :  
Directive Européenne 73/23/EEC  
Directive Européenne 89/336/EEC  
EN60950:1992+A1+A2+A3+A4+A11  
EN55022 (classB):1997 EN50082-1:1992  
EN61000-3-2:1995  
EN61000-3-3:1995  
Hinweis zur Ergonomie :  
Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach ZH1/618/10.80 durch die  
Ansteuerung mit der VGA - Videokarte, 1024 Punkte x 768 Zeilen, RGB analog, 0,7 Vp-p und  
mindestens 85,0 Hz Bildwiederholfrequenz, (non interlaced).  
Weiterhin wird aus ergonomischen Gründen empfohlen, die Grundfarbe Blau nicht auf dunklem  
Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem  
Zeichenkontrast.)  
PTB Note  
Eigensichere Kathodestranlröhre nach Anlage III Röntgenverordnung. Die in diesem Geraet  
entstehende Röntgenstrahlung ist durch die eigensichere Kathodenstrahlroehre ausreichend  
abgeschirmt.  
Recycle Auskunft  
Die Rücknahme dieses Produktes nach Nutzungsende übernimmt EIZO in Deutschland  
zusammen mit dem Partner von Roll MBB Recycling GmbH.  
Dort werden die Geräte in ihre Bestandteile zerlegt, die dann der Wiederverwertung zugeführt  
werden. Um einen Abholtermin zu vereinbaren und die aktuellen Kosten zu erfahren, benutzen  
Sie bitte folgende Rufnummber: 02153-73 35 00. Weitere Informationen finden Sie auch unter  
der Internet-Adresse: www.eizo.de.  
Hinweis  
Die Bildroehre dieses Monitors is frei von Cadmium.  
For U.S.A, Canada, etc. (rated 100-120 Vac) Only  
FCC Declaration of Conformity  
We, the Responsible Party  
EIZO Nanao Technologies Inc.  
5710 Warland Drive, Cypress, CA 90630  
Phone: (562) 431-5011  
declare that the product  
Trade name: EIZO  
Model: FlexScan T550  
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to  
the following two conditions: (1) this device may not cause harmful interference, and (2)  
this device must accept any interference received, including interference that may cause  
undesired operation.  
This equipment has been tested and found to comply with the limits for a Class B digital  
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provided  
reasonable protection against harmful interference in a residential installation. This  
equipment generates, uses, and can radiate radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off and on, the user  
is encouraged to try to correct the interference by one or more of the following measures.  
*Reorient or relocate the receiving antenna.  
*Increase the separation between the equipment and receiver.  
*Connect the equipment into an outlet on a circuit different from that to which the receiver  
is connected.  
*Consult the dealer or an experienced radio/TV technician for help.  
Changes or modifications not expressly approved by the party responsible for compliance  
could void the users authority to operate the equipment.  
Note  
Use the attached specified cable below or EIZO signal cable with this monitor so as to keep  
interference within the limits of a Class B digital device.  
-AC Cord  
-Sielded Signal Cable (D-SUB mini 15 pin - D-SUB mini 15 pin, the enclosed signal cable)  
Canadian Notice  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.  

HP Hewlett Packard D8896HP User Manual
Hanns G Computer Monitor HA192 User Manual
Envision Peripherals LCD User Manual
Electrolux CF604 User Manual
CDA HVC90 User Manual
Cadco LINE CHEF XAF 113 User Manual
Avaya one X Deskphone Value Edition 1608 User Manual
AT T E5634B User Manual
AMX VPN CP User Manual
Acnodes PMW6190 User Manual