Eizo EIZO FlexScan L330 User Manual
For Microsoft Windows CE 2.12  
Version C  
LCD Monitor integrated  
Windows-based Terminal  
Touch Panel  
LCD Monitor integrated  
Windows-based Terminal  
Please confirm the version of the software built in eClient, and refer to  
the suited User's Manual (Refer to the User's Manual Version List on  
next page).  
This is the manual for the following software version.  
*
*
*
Microsoft Windows CE: 2.12 Rev.3.53 or later  
Microsoft Terminal Server Client: Ver.5.60 or later  
ICA Client: Ver.6.30 [Build 1078] or later  
User’s Manual Version List  
A handling description changes with versions of the software built in eClient. Please  
refer to below.  
NOTE  
• The version of software built in eClient can be checked with a [System]-[ICA] tab of  
[Terminal Properties].  
OS: Microsoft Windows CE 2.12  
Software  
Microsoft  
Windows  
Terminal Server  
ICA Client  
Software  
Microsoft Windows CE  
Manual  
C
Version 6.30  
[Build1078] or later  
2.12 Rev.3.53 or later  
2.12 Rev.3.51 or later  
2.12 Rev.3.50 or later  
Version 5.60 or later  
Version 5.60 or later  
Version 5.51 or later  
(This Manual)  
Version 6.20  
[Build992] or later  
B
A
Version 6.20  
[Build992] or later  
English  
SAFETY SYMBOLS  
This manual uses the safety symbols below. They denote critical information. Please read them  
carefully.  
WARNING  
Failure to abide by the information in a WARNING may result in serious injury and  
can be life threatening.  
CAUTION  
Failure to abide by the information in a CAUTION may result in moderate injury  
and/or property or product damage.  
Indicates a prohibited action.  
Indicates to ground for safety.  
Copyright© 2002-2003 EIZO NANAO CORPORATION All rights reserved. No part of this  
manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any  
means, electronic, mechanical, or otherwise, without the prior written permission of Eizo Nanao  
Corporation.  
Eizo Nanao Corporation is under no obligation to hold any submitted material or information  
confidential unless prior arrangements are made pursuant to Eizo Nanao Corporation's receipt of  
said information. Although every effort has been made to ensure that this manual provides up-  
to-date information, please note that EIZO monitor specifications are subject to change without  
notice.  
ENERGY STAR is a U.S. registered mark.  
Apple and Macintosh are registered trademarks of Apple Computer, Inc.  
VGA is a registered trademark of International Business Machines Corporation.  
DPMS is a trademark and VESA is a registered trademark of Video Electronics Standards  
Association.  
Windows is a registered trademark of Microsoft Corporation.  
ScreenManager and PowerManager are trademarks of Eizo Nanao Corporation.  
FlexScan and EIZO are registered trademarks of Eizo Nanao Corporation.  
As an ENERGY STAR® Partner, Eizo Nanao Corporation has determined that this  
product meets the ENERGY STAR guidelines for energy efficiency.  
3
English  
TABLE OF CONTENTS  
1. INTRODUCTION..................................................................................... 5  
1-1. General Description......................................................................................5  
1-2. Features ........................................................................................................6  
1-3. Package Contents..........................................................................................6  
1-4. Controls & Connectors ................................................................................7  
1-5. Overview ......................................................................................................9  
2. CONNECTING THE eClient.................................................................. 10  
2-1. Setting up the eClient..................................................................................10  
2-2. Connecting the eClient................................................................................11  
3. SETTING UP THE eClient .................................................................... 13  
3-1. WBT Setup Wizard.....................................................................................13  
3-2. Dial-Up Connection (531L/531LT-GR only)...............................................27  
4. ADDING & CHANGING A CONNETION NAME................................... 34  
4-1. Adding a Connection Name........................................................................34  
4-2. Deleting a Connection ................................................................................52  
4-3. Editing a Connection ..................................................................................53  
4-4. Setting an Autostart Connection.................................................................55  
5. LOGON & LOGOFF.............................................................................. 56  
5-1. Logon to a WTS .........................................................................................56  
5-2. Logoff from the WTS..................................................................................59  
6. USING THE TERMINAL PROPERTIES ................................................ 61  
6-1. General Information & Reset to Default ....................................................61  
6-2. Input Devices Settings.................................................................................63  
6-3. Colors & Power Save Settings.....................................................................68  
6-4. Network Settings ........................................................................................70  
6-5. Printer Settings............................................................................................73  
6-6. Dial-Up (PPP) Connection Settings (531L/531LT-GR only) ........................76  
6-7. ICA Settings................................................................................................77  
6-8. Product Information, Security, & Updating Software .................................80  
7. PRACTICAL SETUP............................................................................. 87  
8.TROUBLESHOOTING........................................................................... 92  
9. CLEANING............................................................................................ 94  
10. SPECIFICATIONS............................................................................... 96  
11. REFERENCE..................................................................................... 100  
11-1. Attaching an Arm Stand .........................................................................100  
INDEX ..................................................................................................... 102  
TABLE OF CONTENTS  
4
English  
1. INTRODUCTION  
Thank you very much for purchasing the EIZO eClient 530L/531L/531LT-GR.  
1-1. General Description  
The eClient is a terminal which displays applications on a Windows Terminal Server  
(WTS) or a web site and conveys input by a keyboard or a mouse to the WTS. To  
operate the eClient, please connect it to a WTS with Microsoft Window NT Terminal  
Server Edition or Windows 2000 Server / Advanced Server / Datacenter Server.  
Windows Terminal Server (WTS)  
eClient  
Output data of  
applications  
Input data from  
keyboard/mouse  
(stylus)  
· Operation of applications  
· Storage of data  
· Display data  
· Operation by keyboard/mouse  
(stylus)  
1. INTRODUCTION  
5
English  
1-2. Features  
• Lower TCO*  
*TCO (Total Cost of Ownership)  
Expense for managing and administrating computer systems.  
• Saves Space and Power Consumption  
• Less Heat, Less Noise  
• 531L/531LT-GR  
*Serial Port for Modem/PDA (*Hayes AT Compatible Modem Supported)  
*Portrait resolution supported  
[In use of the Citrix ICA Client (ICA)]  
• 531LT-GR  
*A Touch Panel and a Stylus Provided  
1-3. Package Contents  
Please contact your local dealer for assistance if any of the listed items are missing or  
damaged. Please make sure that all the listed items are in the package.  
• eClient 530L/531L/531LT-GR  
• Mouse  
• Power Cord  
• Screw (M4 x 12 mm) x 4  
• User’s Manual  
• Stickers of the Brightness Control Guide  
• Stylus (531LT-GR only)  
NOTE  
• We recommend that you retain the original packing materials in case of future need.  
• A keyboard is not included. It must be purchased separately.  
• Key combinations on the keyboard can adjust brightness (see page 69). Key  
combinations for an adjustment are presented on the stickers. Please apply them  
for your convenience.  
Please use the enclosed mouse. Eizo Nanao Corporation will no be held responsible for  
accident or damage caused by the use of a mouse manufactured by other companies.  
6
1. INTRODUCTION  
English  
1-4. Controls & Connectors  
Front  
(1) (2)  
(1) Power Switch  
(2) Power Indicator  
Power Indicator  
Green  
Unit  
Operation  
Screen saver mode  
Power save mode  
Yellow  
NOTE  
• When turning off/on the unit, leave the unit off for a few seconds before turning  
it on again.  
1. INTRODUCTION  
7
English  
Rear  
(10)  
(8)  
(9)  
(11)  
(3)(4) (5)  
(6)  
(7)  
(3) Mouse Connector  
(4) Keyboard Connector  
(5) Ethernet Connector (10 Base-T)  
(6) Parallel Connector  
(7) Power Connector  
(8) Serial Connector (RS-232C) (531L/531LT-GR)  
(9) Security Lock*1  
(10) Holes for Mounting an Arm Stand*2  
(11) Stand  
1
*
This allows for connection of a security cable. This lock supports Kensington's  
MicroSaver security system. For further information, please consult:  
Kensington Technology Group  
2855 Campus Drive, San Mateo, CA  
94403 USA  
1-800-650-4242, x3348  
Intl: 650-572-2700  
Fax: 650-572-9675  
http://www.kensington.com  
Please see “11. REFERENCE” on page 100 for details.  
2
*
8
1. INTRODUCTION  
English  
1-5. Overview  
Directions for the eClient’s Setup  
2. CONNECTING THE  
p.10  
3. SETTING UP THE eClient  
3-1. WBT Setup Wizard  
p.13  
p.27  
3-2. Dial-Up Connection  
4. ADDING & CHANGING A CONNETION NAME  
4-1. Adding a Connection Name  
4-2. Deleting a Connection  
p.34  
p.52  
p.53  
p.55  
4-3. Editing a Connection  
4-4. Setting an Autostart Connection  
Directions for the eClient’s Operation.  
5. LOGON & LOGOFF  
5-1. Logon to a WTS  
p.56  
p.59  
5-2. Logoff from the WTS  
Directions for Changing Terminal Properties’ Settings.  
6. USING THE TERMINAL PROPERTIES  
6-1. General Information & Reset to Default  
6-2. Input Devices Settings  
p.61  
p.63  
p.68  
p.70  
p.73  
p.76  
p.77  
p.80  
6-3. Colors & Power Save Settings  
6-4. Network Settings  
6-5. Printer Settings  
6-6. Dial-Up (PPP) Connection Settings  
6-7. ICA Settings  
6-8. Product Information, Security, & Updating Software  
Directions for Using a DHCP Server, a Practical Setup  
7. PRACTICAL SETUP  
p.87  
1. INTRODUCTION  
9
English  
2. CONNECTING THE eClient  
This chapter shows how to connect the eClient to a WTS.  
2-1. Setting up the eClient  
Please observe the following cautions when connecting the eClient.  
WARNING  
Place the eClient on a strong, stable surface.  
A unit placed on an inadequate surface may fall, resulting in injury  
or equipment damage. If the unit falls, disconnect the power  
immediately and have the unit checked by a qualified service  
engineer before using it again. Using a unit after it has been  
dropped may result in fire or electric shock.  
Set the unit in an appropriate location.  
* Do not install in a dusty or humid environment.  
* Do not place in a location where steam can have direct contact  
with the screen.  
* Do not place near heat generating devices or a humidifier.  
10 2. CONNECTING THE eClient  
English  
2-2. Connecting the eClient  
NOTE  
• Before connecting the eClient, confirm the following:  
• The eClient is turned off.  
• The WTS is turned on.  
• Connect the peripherals to the appropriate connectors of the unit.  
1. In case of connecting the WTS through LAN:  
Connect the eClient to the network with an ethernet cable.  
In case of a dial-up or dial-in connection (531L/531LT-GR only):  
Connect the eClient to a modem or a modem card.  
Modem  
Card  
Power Cord  
Printer  
Network  
Keyboard  
Mouse  
2. Plug a keyboard and a mouse into the eClient. If using other devices,  
please connect them to the appropriate connectors.  
If using a touch panel, a mouse should not be connected (531LT-GR only).  
2. CONNECTING THE eClient 11  
English  
3. Plug the power cord into the power connector.  
WARNING  
Use the enclosed power cord and connect to the standard  
power outlet of your country.  
Be sure to remain within the rated voltage of the power cord.  
Not doing so may cause in fire or electric shock.  
The equipment must be connected to a grounded main  
outlet.  
Not doing so may cause in fire or electric shock.  
12 2. CONNECTING THE eClient  
English  
3. SETTING UP THE eClient  
This chapter presents how to prepare for a connection with a WTS when the eClient  
starts up for the first time.  
3-1. WBT Setup Wizard  
1. Turn on the power switch.  
The power indicator turns green.  
NOTE  
• When no picture is displayed, or when the following message is shown on the  
screen, please refer to “8. Troubleshooting” on page 92.  
- Message -  
In use of a stylus or a finger as an input device, “No Mouse Connected!!” caution  
does not effect your operation (531LT-GR only).  
3. SETTING UP THE eClient 13  
English  
2. “Touch panel calibration” is displayed (531LT-GR only).  
Five targets are displayed on the screen. Press the targets with a stylus or a  
fingertip to locate the center of the touch panel. If you accidentally touched the  
screen in the wrong spot during calibration, you will distort the touch panel  
calibration.  
3. “Calibration measured” window is displayed when you finished  
(531LT-GR only).  
Click the “Enter” key to accept the settings.  
14 3. SETTING UP THE eClient  
English  
4. “WBT Setup Wizard” is displayed.  
Click [Next>].  
5. End User License Agreement page is displayed.  
Read the content and click [Accept] to continue.  
3. SETTING UP THE eClient 15  
English  
6. IP address setting page is displayed.  
[Yes, use the IP information supplied by DHCP.]  
...................................Select this when using DHCP service. All the  
necessary information of the eClient including the IP  
address will be obtained by the DHCP.  
[No, I will enter static IP information.]  
...................................Select this when not using DHCP service. Enter the IP  
address of the eClient.  
If DHCP service is not in operation, following message  
appears.  
Type a [Terminal Name] for connection to a WTS by the RDP (Microsoft Remote  
Desktop Client) protocol.  
[Terminal Name] ................Type the name to identify this unit on the network.  
Click [Next>].  
Refer to step 8 if you select [Yes, use the IP information supplied by DHCP.]  
Refer to step 7 if you select [No, I will enter static IP information.]  
16 3. SETTING UP THE eClient  
English  
7. IP address page is displayed.  
[IP Address] ........................Type the IP address of the unit.  
[Subnet Mask] ....................Type the subnet mask of the network.  
[Gateway]...........................Type IP address of the Gateway machine if necessary.  
Click [Next>] when finished.  
3. SETTING UP THE eClient 17  
English  
8. DNS and WINS settings page is displayed.  
This check box should be marked when DNS or WINS is used.  
NOTE  
• Skip the page by clicking [Next>] if DNS or WINS is not used.  
If using DNS  
Click the [Enable DNS] check box to activate this box.  
[Default Domain Name] .....Type the default domain name.  
[Primary Server IP]..............Type the DNS primary Server IP address.  
[Secondary Server IP]..........Type the DNS secondary Server IP address.  
If using WINS  
Click the [Enable WINS] check box to activate this box.  
[Primary Server IP]..............Type the WINS primary Server IP address.  
[Secondary Server IP]..........Type the WINS secondary Server IP address.  
Click [Next>] when finished.  
18 3. SETTING UP THE eClient  
English  
9. Desktop area resolution and color settings page is displayed.  
Select the preferable display mode from the two available modes:  
· 1024 x 768 (256 colors)  
· 1024 x 768 (65,536 colors)  
· 768 x 1024 (256 colors) (531L/531LT-GR only)  
· 768 x1024 (65,536 colors) (531L/531LT-GR only)  
NOTE  
• The orientation of 768 x 1024 is a portrait. (768 x 1024 available for Citrix ICA.  
When RDP is used, 640 x 480 is displayed on center of the screen.)  
To use the portrait orientation mode, please change the monitor’s tilt stand to  
an arm, and set the monitor portrait (90° clockwise).  
Click [Next>] when finished.  
3. SETTING UP THE eClient 19  
English  
10. Local Printer Setup page is displayed.  
NOTE  
• The following is required to install a local printer;  
* A printer is connected to the printer port or the serial connector of the eClient.  
* An RDP protocol is used for connection to a WTS.  
* Microsoft Windows 2000 Server / Advanced Server / Datacenter Server is  
installed in a WTS  
• A Local Printer mentioned here is a printer connected directly to the Parallel  
Connector of the unit.  
Select [Yes] when using a local printer.  
Select [No] in the following cases:  
* When not using a Local Printer  
* When using a ICA protocol for connection to a Server  
* When the OS of the Server is Windows NT Server 4.0 Terminal Server  
Edition  
Click [Next>] when finished.  
Refer to step 11 if selecting [Yes].  
Refer to step 17 if selecting [No].  
20 3. SETTING UP THE eClient  
English  
11. Printer port selection page is displayed.  
Select a printer port.  
The eClient supports LPT1.  
Click [Next>].  
3. SETTING UP THE eClient 21  
English  
12. Printer model selection page is displayed.  
Select a manufacturer and model of your printer.  
[User Defined].....................Click the check box if your printer is not listed.  
Click [Next>] when finished.  
Refer to step 13 if clicking [User Defined].  
Refer to step 14 if not clicking [User Defined].  
13. Printer model and manufacturer settings page is displayed.  
[Model Name] ....................Type a model and manufacturer of your printer.  
Click [Next>] when finished.  
22 3. SETTING UP THE eClient  
English  
14. Printer name setting page is displayed.  
Name the printer or use the indicated name. (Some programs do not support the  
Server and the printer name combinations of more than 31 characters.)  
Click [Next>] when finished.  
3. SETTING UP THE eClient 23  
English  
15. Default printer setting page is displayed.  
Select [Yes] to set this printer as the default printer.  
Select [No] not to set this printer as the default printer.  
Click [Next>].  
24 3. SETTING UP THE eClient  
English  
16. Another printer configuration page is displayed.  
Select [Yes] to configure another printer.  
Select [No] to finish printer settings.  
Click [Next>] when finished.  
Refer to step 11 if selecting [Yes].  
Refer to step 17 if selecting [No].  
3. SETTING UP THE eClient 25  
English  
17. The last page of the “WBT Setup Wizard” is displayed.  
Click [Finish] in the last page to display a “Terminal Settings change” dialog box.  
(This dialog box is displayed only when there are changes in the settings.)  
Click [Yes] to restart the eClient to activate the changes.  
· Click [No] to finish the “WBT Setup Wizard” and display “Terminal Connection  
Manager” on the screen. The setting is not activated until the eClient is  
restarted.  
This completes the eClient settings.  
The “Terminal Connection Manager” dialog box will be displayed after restarting.  
NOTE  
• When you are connecting to the WTS with a LAN card, another installation for  
a LAN card connection must be completed. Please follow the next page.  
• When you are connecting to the WTS with a modem, another installation for a  
modem connection (a dial-up connection) must be completed. Please follow  
the “3-2. Dial-up Connection”, page 27.  
26 3. SETTING UP THE eClient  
English  
3-2. Dial-Up Connection (531L/531LT-GR only)  
The following details the installation of a dial-up connection for RAS (Remote Access  
Service).  
No restriction of the protocol is made for the “Dial-up connection”. To use a dial-up  
connection requires an RAS server in operation.  
[Dial-up Connection]  
Telephone  
Lines  
RAS Server  
WTS  
FTP Server  
eClient  
WTS  
NOTE  
• Another type of connection using a modem, a dial-in connection, is available to  
connect to the WTS with an ICA protocol. Please see page 40.  
[Dial-in Connection]  
Telephone  
Lines  
WTS  
eClient  
1. Press “F2” key in the “Terminal Connection Manager”.  
3. SETTING UP THE eClient 27  
English  
2. “Terminal Properties” is displayed.  
Click the [Network] tab.  
3. The network setting window is displayed.  
Select [Use PPP connection or another network adapter].  
Click [PPP] tab when finished.  
28 3. SETTING UP THE eClient  
English  
4. The dial-up setting window is displayed.  
NOTE  
• Enter your information in the pertinent fields.  
[Connection Name] ............Choose a connection name for a dial-up connection.  
([None] indicates no connection name chosen.)  
[New...]...............................Click the button to create a new dial-up connection  
name.  
“Create New Dial-Up Connection” dialog box is  
displayed.  
Enter the name and click [OK].  
[Remove] ............................Delete the connection name displayed currently.  
[Dialing Settings]  
[Select Dial-In Device].........Choose a modem connecting device type.  
[Country Code:], [Area Code:], [Phone Number]  
...................................Enter a country code, an area code, and a phone  
number for the connection name.  
[Force long distance]...........Click here to use the country code, area code, and the  
phone number when connecting to the connection  
name.  
[Force local]........................Click here to use only the phone number when  
connecting to the connection name. (In case the area  
code of the connection name is different from the  
present area code.)  
3. SETTING UP THE eClient 29  
English  
[Dialing Properties...]  
...................................Click the button to set information of the sender.  
[When dialing from:] ..........Choose the sender’s location.  
[New...]...............................Click this to add a new sender’s location.  
“Create New Location” dialog box is displayed.  
Enter a new sender’s location and click [OK].  
[Remove] ............................Remove the current sender’s location.  
[Local Settings are...]  
[The local area code is:], [The local country code is:]  
...................................Enter the area code and the country code of the  
sender’s location.  
[Dial using:] ........................Choose your using dial from;  
[Tone] / [Pulse]  
[Disable call waiting by dialing:]  
...................................Click the check box and enter the number to disable  
call waiting by dialing.  
[Dialing Patterns...].............Click the button and use this group box to set your  
modem’s dialing patterns.  
Click [OK] when finished.  
Click [OK] of the [Dialing Properties] when finished.  
“Terminal Properties” is displayed.  
30 3. SETTING UP THE eClient  
English  
[Device Configure...]  
...................................Click the button the detailed settings of the modem.  
(Please refer to the instruction manual of a modem for  
settings of the modem.)  
[Port Settings] tab  
[Manual Dial (user supplies dial strings)]  
...................................Click this box to set up for manual dialing.  
[Terminals]  
[Use terminal window before / after Dialing]  
...................................Click this box to record terminal window information  
before or after dialing.  
[Connection Preferences]  
[Baud Rate].........................Set data transmission rate from 110 to 115,200 bps.  
[Data Bits]...........................Set data bits.  
[Parity]................................Set enabling to check the data's transmission.  
[Stop Bits]...........................Set length of the Stop Bits.  
[Flow Control]....................Set Flow Control.  
[Call Option] tab  
[Cancel the call if not connected within]  
...................................Click the box and set the intervals to the right box  
before canceling the connection in case of connection  
failure.  
[Wait for dial tone before dialing]  
...................................Click to dial after dial tone.  
[Wait for credit card tone]  
...................................Click the box and set the intervals before canceling the  
connection in use of a credit card for dialing.  
[Extra Settings (Special modem commands may be inserted into the dial strings)]  
...................................Enter a special modem command if required.  
Click [OK] on [Device Properties] when finished. “Terminal Properties” will be  
displayed.  
NOTE  
• When changing settings in the [Device Properties], click the [Call Option] tab  
before clicking [OK] to close the window.  
3. SETTING UP THE eClient 31  
English  
[TCP/IP Settings...]  
Click the button to set the TCP/IP settings of the WTS.  
[Use server-assigned IP address]  
...................................Click the box to use a server-assigned IP address.  
[Specify an IP address] ........Enter a provided IP address.  
[Use server-assigned DNS or WINS server IP address]  
...................................Click the box to use a server-assigned DNS or WINS  
server IP address.  
[Specify DNS or WINS server IP address]  
...................................Enter an DNS or WINS server IP address provided.  
32 3. SETTING UP THE eClient  
English  
[Primary DNS], [Secondary DNS]  
...................................Enter IP address of the primary DNS and IP address of  
the secondary DNS.  
[Primary WINS], [Secondary WINS]  
...................................Enter IP address of the primary WINS and IP address  
of the secondary WINS.  
[Use software compression]  
...................................Click to use software compression.  
[Use IP header compression]  
...................................Click to IP header compression.  
[Use default gateway]..........Click to use the default Gateway.  
Click [OK] in the [TCP/IP Settings] when finished.  
“Terminal Properties” is displayed.  
[User’s Name], [Password], [Domain]  
...................................Enter your information in the pertinent fields. If you  
do not know the information, contact your system  
administrator.  
[Save the password] ............Click to save the password.  
Click [OK] in the “Terminal Properties” when finished.  
The “Terminal Properties” saves the settings and close.  
This completes the dial-up connection settings.  
A small window will be displayed on the right bottom of the window if the settings  
are successfully installed.  
3. SETTING UP THE eClient 33  
English  
4. ADDING & CHANGING A  
CONNETION NAME  
This chapter shows how to add, delete, and modify connection names to a WTS.  
All the settings are managed in the “Terminal Connection Manager”.  
4-1. Adding a Connection Name  
These are settings for the Server connection.  
Each protocol has different settings. Please install the appropriate settings.  
• In use of the Microsoft Remote Desktop Client (RDP) page 35  
• In use of the Citrix ICA Client (ICA)  
page 40  
NOTE  
• Please install Citrix MetaFrame server into the Server when using the ICA protocol.  
34 4. ADDING & CHANGING A CONNETION NAME  
English  
In Use of RDP Protocol  
1. Display [Terminal Connection Manager].  
Click the [Configure] tab and [Add...] to set the connection information of the  
WTS.  
2. Protocol selection dialog box is displayed.  
Select the “Microsoft Remote Desktop Client” (RDP)  
Click [OK] when finished.  
4. ADDING & CHANGING A CONNETION NAME 35  
English  
3. “WTS Connection Wizard” is displayed.  
[Name]................................Type the connection name to the Server. Name the  
connection to differentiate the Server from others.  
[Server] ...............................Type the IP address or the name of the Server, or  
WINS setting is necessary when the name is typed.  
[Low Speed Connection].....Click the check box when making a low speed  
connection. Enable this function when connecting  
through a Remote Access Service using a modem that  
takes time to receive data from the Server.  
Click [Next>] when finished.  
36 4. ADDING & CHANGING A CONNETION NAME  
English  
4. Automatic Logon setting page is displayed.  
Type the name, the password, and the domain name of the WTS beforehand to  
enable an Automatic Logon to the WTS after connecting.  
NOTE  
• If an Automatic Logon is not needed, click [Next>].  
Click the check box of the [Automatic Logon] to enable the item.  
[Username]..........................Type the name to connect the WTS.  
[Password]..........................Type the password for the user name.  
[Domain] ............................Type the domain name.  
Click [Next>] when finished.  
4. ADDING & CHANGING A CONNETION NAME 37  
English  
5. Specifying an application to run after connecting to a WTS is  
displayed.  
Select whether to display the Windows desktop screen or start up an application.  
[Desktop]............................Select this to start the Windows desktop screen when  
you connect.  
[Application file name:] .....Select this to start an application when you connect.  
[Working directory:]...........Input the name of the application and the working  
directory if necessary.  
NOTE  
• When the [Application file name:] and the [Working Directory] are named, only  
the specified application will be started after logging on. In this case, closing  
the application logs off and disconnects from the WTS.  
Click [Next>] when finished.  
38 4. ADDING & CHANGING A CONNETION NAME  
English  
6. The last page of the “WTS Connection Wizard” is displayed on the  
screen.  
Click [Finish] to return to the “Terminal Connection Manager” dialog box.  
The registered connection name is displayed in the “Terminal Connection  
Manager” dialog box.  
This completes the setup of the eClient for connection to a WTS with the RDP  
protocol.  
NOTE  
• Please repeat step 1 to 6 to entry more than two kinds of connections.  
4. ADDING & CHANGING A CONNETION NAME 39  
English  
In Use of the ICA protocol  
1. Click the [Configure] tab.  
Click [Add...].  
2. “New Connection” dialog box is displayed on the screen.  
Select “Citrix ICA Client” (ICA).  
Click [OK] when finished.  
40 4. ADDING & CHANGING A CONNETION NAME  
English  
3. “Specify Connection Type” dialog box is displayed.  
[Network Connection]........Select for network connection.  
[Dial-In Connection]...........Select for dial-in connection.  
Click [Next>] when finished.  
Go to step 4 when selecting [Network Connection].  
Go to step 5 when selecting [Dial-In Connection].  
4. ADDING & CHANGING A CONNETION NAME 41  
English  
4. Citrix Server or published application selection page is displayed.  
1)Select [Server] (WTS) or [Published Application].  
2)Click [Server Location…].  
[Server Group]................Select the WTS Group to connect. (A WTS Group  
consists of [Primary], [Backup 1], and [Backup 2].  
The WTS will be searched in order of [Primary],  
[Backup 1], and [Backup 2].  
[Add]...............................Add another Server address. Type the Server Name  
or IP address. (The typed Server Name or IP  
address will be shown in the [Address] list.  
[Delete]...........................Delete the selected WTS from the [Address] list.  
[Default List] ...................Revert the state of the [Address] list to the saved one.  
[Address]........................The added WTS IP address appears.  
Click the drop-down list box below [Address]. Select the appropriate WTS  
protocol from the list.  
[TCP browser] ................Citrix MetaFrame uses UDP protocol to search for the  
WTS. Select this when using a UDP protocol.  
[TCP + HTTP browser]...Select this when not using a UDP because of the  
firewall in your network environment.  
[SSL + HTTPS browser]  
...................................This is not available with eClient.  
Click [OK] to return to the previous page and save the adjustments.  
42 4. ADDING & CHANGING A CONNETION NAME  
English  
3)Click [Refresh] to refresh the list to the newest information.  
4)Select a WTS or a published application from the list.  
NOTE  
• Published applications are specific application set by a system administrator.  
When connected, you are presented with the application itself.  
Click [Next>].  
4. ADDING & CHANGING A CONNETION NAME 43  
English  
5. “Dial-In Devices” dialog box is displayed.  
NOTE  
• This setting is available in the 531L/531LT-GR only.  
• A dial-in connection is not available during a dial-up connection. Disconnect  
the dial-up connection before making dial-in connection.  
[Dial-In Device:]..................Select the device name connected to the modem.  
[Hayes Compatible on COM1] is available for the  
eClient.  
[Phone Number] .................Enter a country code, an area code, and a phone  
number for the connection.  
[Use Tone Dialing]..............Click to use tone dialing.  
[Configure] .........................Click the button the detailed settings of the modem.  
(Please refer to the instruction manual of the modem  
for details.)  
[Port Settings] tab  
[Manual Dial (user supplies dial strings)]  
...................................Click this box to set up for manual dialing.  
[Terminals]  
[Use terminal window before dialing]  
...................................Click this box to record terminal window information  
before dialing.  
[Use terminal window after dialing]  
...................................Click this box to record terminal window information  
after dialing.  
44 4. ADDING & CHANGING A CONNETION NAME  
English  
[Connection Preference]  
[Baud Rate].........................Set the data transmission rate from 110 to 115,200.  
[Data Bits]...........................Set the data bits.  
[Parity]................................Set to check the data’s appropriate transmission.  
[Stop Bits]...........................Set the length of the Stop Bits.  
[Flow Control]....................Set Flow Control.  
[Call Option] tab  
[Cancel the call if not connected within]  
...................................Click the box and type the interval to the right box  
before canceling the connection in case of connection  
failure.  
[Wait for dial tone before dialing]  
...................................Click to dial after dial tone.  
[Wait for credit card tone]  
...................................Click to set the intervals before canceling the  
connection using a credit card.  
[Extra Settings (Special modem commands may be inserted into the dial strings)]  
...................................Enter a special modem command if needed.  
Click [OK] on [Device Properties] when finished. The dialog box saves the settings  
and closes.  
• Click the [Close] button to cancel the settings.  
NOTE  
• When changing settings in the [Device Properties], click the [Call Option] tab  
before clicking [OK] to close the window.  
Click [Next>].  
4. ADDING & CHANGING A CONNETION NAME 45  
English  
6. A title for the ICA connection page is displayed.  
Type a connection name of the WTS.  
Click [Next].  
7. An application selection page is displayed.  
Specify the command line and the working directory of an application to operate.  
NOTE  
• Leave these fields blank and click [Next>] to run a Windows desktop.  
[Command Line:]................Type the application name and the path.  
[Working Directory:] ..........Type the working directory for the application.  
NOTE  
• When the [Command Line] and the [Working Directory] are named, only the  
specified application will be started after logging on. In this case, closing the  
application logs off from the WTS.  
Click [Next>] when finished.  
46 4. ADDING & CHANGING A CONNETION NAME  
English  
8. Automatic logon settings page is displayed.  
Type the name, the password, and the domain name of the WTS beforehand to  
enable an Automatic logon to the WTS after connecting.  
NOTE  
• If an Automatic Logon is not needed, click [Next.]  
[User Name:].......................Type the name to automatically connect the WTS.  
[Password:].........................Type the password for the user name.  
[Domain:] ...........................Type the domain name.  
[Allow Smart Card logon]...This is not available with eClient.  
Click [Next>] when finished.  
4. ADDING & CHANGING A CONNETION NAME 47  
English  
9. Colors selection page is displayed.  
Set the colors of the WTS’ screen.  
NOTE  
• Thousands can be selected only when the color setting of the eClient is 65536  
colors.  
Click [Next>] when finished.  
48 4. ADDING & CHANGING A CONNETION NAME  
English  
10. Compression and encryption, and sound settings page is displayed.  
[Use Printer Configuration Utility]  
...................................Click the check box to install the printer at the [ICA  
Client Printer Configurations].  
[Compress Data Stream].....Click the check box to reduce the amount of data  
transferred between the WTS and the eClient, which  
can increase performance. (If you have sufficient  
bandwidth, leave compression off to conserve  
processing power on the WTS.)  
[SpeedScreen:].....................Select the speed at which the keyboard and mouse  
perform on the screen.  
Select [On] when connecting to the WTS with a  
dial-up connection. Select [Off] when connecting to  
the WTS with a LAN connection. Select [Auto] to  
automatically switch the speed depending on the  
network environment.  
[Encryption Level:] .............Encryption level can be selected from RC5 (128 bit -  
Login Only), basic, RC 5 (40 bit), RC5 (56 bit), RC5  
(128 bit). The level becomes higher as the bit gains.  
RC5 (128 bit - Login Only) indicates the 128 bit level  
security available only at logon.  
Click [Next>] when finished.  
4. ADDING & CHANGING A CONNETION NAME 49  
English  
11. Firewall settings page is displayed.  
NOTE  
• These settings are effective when connecting to the WTS through internet.  
• If no change is made, the settings under the [Firewall settings] of [Global ICA  
Client Settings] will be applied (see page 78 for details).  
Set the connection to the WTS through the SOCKS proxy server when the SOCKS  
proxy server is working to limit the access to the WTS.  
[Proxy]  
Click the drop-down list box, and select [SOCKS] from the list.  
(The [Secure (HTTPS)] setting is not available with eClient.)  
[Address of SOCKS proxy to use] / [Port]  
...................................Type the IP address of the SOCKS proxy server and  
the port number of the proxy server.  
[Use alternate address through firewalls]  
...................................Click the check box to connect to the WTS through  
the Firewall.  
[SSL/TLS Relay]  
[Address of SSL relay to use] / [Port]  
...................................These are not available with eClient.  
Click [Finish] when finished.  
[Terminal Connection Manager] is displayed.  
The registered connection name is displayed in the “Terminal Connection  
Manager” dialog box.  
50 4. ADDING & CHANGING A CONNETION NAME  
English  
This completes the setup of the eClient for connection to a Server with the ICA  
protocol.  
NOTE  
• Please repeat the step 1 to 11 when you adding another connection name.  
4. ADDING & CHANGING A CONNETION NAME 51  
English  
4-2. Deleting a Connection  
This function deletes an existing Connection Name.  
1. Display the “Terminal Connection Manager” dialog box.  
2. Click the [Configure] Tab.  
3. Select the Connection Name you want to delete.  
4. Click [Delete].  
5. “Confirm Connection Delete” dialog box is displayed.  
Click [Yes] to delete the information of the selected WTS.  
52 4. ADDING & CHANGING A CONNETION NAME  
English  
4-3. Editing a Connection  
This function modifies attributes of the WTS connections.  
1. Display the “Terminal Connection Manager” dialog box.  
2. Click the [Configure] Tab.  
3. Select the connection you want to modify.  
4. Click [Edit...].  
5. [Edit Connection] dialog box or [Edit Connection Details] is  
displayed.  
•
For RDP Connection  
(Please see pages 35 to 39 for each setting.)  
[Net Connections] tab........Change connection settings to a WTS.  
[Application] tab................Change a description of an application on a startup.  
Click [OK] to enable the settings.  
4. ADDING & CHANGING A CONNETION NAME 53  
English  
•
For ICA Connection  
(Please see to pages 40 to 50 for each setting.)  
[Server/Dial-In] tab .............Either Server or Dial-In tab is displayed depending on  
the connection type.  
[Server] Tab (for LAN connection)  
To change the WTS / the public application to use  
[Dial-In] Tab (for Dial-In connection)  
To change settings of the Dial-In connection  
(531L/531LT-GR only)  
[Application] tab.................To change a description of an application to run  
[Logon] tab.........................To set/cancel Automatic Logon  
[Windows] tab ....................To set the colors of the WTS screen  
[Options] tab ......................To set/cancel the printer after connecting the WTS,  
compression of data, the speed at which the keyboard  
and mouse perform on the screen, and encryption level  
setting.  
[Title] tab............................To change the connection name  
[Firewall Settings] tab .........To change the settings on the Firewall and the proxy  
WTS  
If no change is made in this settings, the settings under  
the [Firewall settings] of “Global ICA Client Settings”  
will be applied (see page 78 for details).  
Click [OK] to enable the settings.  
NOTE  
• When changing settings in the Dial-In connection, click and show the [Call  
Option] tab of [Device Properties] of the [Dial-In] tab before clicking [OK] to  
close the window.  
54 4. ADDING & CHANGING A CONNETION NAME  
English  
4-4. Setting an Autostart Connection  
This function configures a connection to start automatically each time the eClient is  
turned on. (This function is available for a LAN connection.)  
1. Display the “Terminal Connection Manager” dialog box.  
2. Click the [Configure] tab.  
3. Select the desired Connection Name for Autostart Connection.  
4. Click [Startup...]  
5. “Connection Startup” dialog box is displayed.  
Select [Automatically start the selected connection at startup.]  
Click [OK] to save the setting. The setting is effective from the next startup.  
4. ADDING & CHANGING A CONNETION NAME 55  
English  
5. LOGON & LOGOFF  
This chapter shows how to log on to and log off from a WTS.  
5-1. Logon to a WTS  
1. Turn on the eClient.  
2. “Terminal Connection Manager” dialog box is displayed.  
Please follow the instruction depending on the network environment of the eClient.  
LAN connection  
Go to step 3.  
Modem connection (531L/531LT-GR only)  
* Dial-Up connection to the RAS Server  
Click the active button of a small window on the right bottom of the screen.  
A dial-up connection is made by clicking the button. Check the clock’s  
running, and go onto step 3.  
* Dial-In connection to the Citrix MetaFrame Server  
Go to step 3.  
NOTE  
• A dial-in connection is not available during a dial-up connection. Disconnect  
the dial-up connection before making dial-in connection.  
56 5. LOGON & LOGOFF  
English  
3. Click the [Connections] tab.  
Select the desired [Connection Name] and click [Connect] (or simply double click  
the connection name).  
NOTE  
• To connect to the default connection WTS set in the “Terminal Connection  
Manager” dialog box, press [Ctrl] + [Alt] + [Home] keys. (See page 55 on a  
default connection server setting.)  
4. The eClient connects to the WTS, and the “Log On to Windows”  
dialog box is displayed.  
Type your [User name] and [Password], and click [OK] to log on to the WTS.  
After logon, the eClient allows you to use Microsoft Windows applications  
running on the WTS.  
NOTE  
• If an Automatic Logon connection has been defined, this menu will not be  
displayed upon connection. (For details, please refer to [Automatic Logon] on  
page 37, 47.)  
5. LOGON & LOGOFF 57  
English  
Multi Session  
You can log on to the WTS with the several connection names, and switch the active  
sessions.  
• Logon  
1. Log on with a Connection Name, as following the previous steps.  
2. Press [Ctrl] + [Alt] + [End] keys after logon.  
3. “Terminal Connection Manager” is displayed.  
Select another Connection Name to log on to, and click [Connect]. (Or double  
click the connection name.)  
4. “Log On to Windows” dialog box is displayed after connecting to  
the WTS.  
Type your [User name] and [Password], and click [OK] to log on to the WTS.  
(Repeat the step 2 to 4 to log on to another connection name.)  
• Switching the Active Session of the WTS  
Press [Ctrl] + [Alt] + [UP ARROW] key / [DOWN ARROW] key to switch the active  
session.  
NOTE  
• The multi session is not available on a dial-in connection. (531L/531LT-GR only)  
58 5. LOGON & LOGOFF  
English  
5-2. Logoff from the WTS  
If your eClient starts its operation with a desktop  
1. Log off from the WTS.  
(1) Close all applications.  
(2) Select [Start] on the taskbar.  
(3) Microsoft Windows NT Server 4.0 Terminal Server Edition:  
Select [Logoff].  
Microsoft Windows 2000 Server / Advanced Server / Datacenter Server:  
Select [Shut Down...] and select [Logoff] of the [Shut Down Windows] dialog  
box.  
(4) Click [OK] on the Logoff Window. The session ends and automatically logs  
off from the WTS. The “Terminal Connection Manager” dialog box is  
displayed.  
If a dial-up connection is running, click the active button of the window on the  
right of the screen. Clicking the button Disconnects the dial-up connection.  
(531/531LT-GR only)  
2. Shut down the eClient.  
5. LOGON & LOGOFF 59  
English  
If your eClient starts its operation with an application  
1. Log off from the WTS.  
Close applications to log off from the WTS.  
“Terminal Connection Manager” is displayed.  
If a dial-up connection is running, click the active button of the window on the  
right bottom of the screen. Clicking the button Disconnects the dial-up  
connection.  
(531L/531LT-GR only)  
2. Shut down the eClient.  
NOTE  
• It is possible to Disconnect from a WTS without closing applications in use (or  
without logging off). (The last view of the application is displayed when the next  
connection to the WTS is made.)  
60 5. LOGON & LOGOFF  
English  
6. USING THE TERMINAL  
PROPERTIES  
This chapter presents how to modify all settings of the eClient using the “Terminal  
Properties”.  
To display the “Terminal Properties” during logging on, press F2 in the “Terminal  
Connection Manager” dialog box. (Press Ctrl + Alt + End to display the “Terminal  
Connection Manager”.)  
6-1. General Information & Reset to Default  
Click [General] tab to confirm general settings and to reset the eClient to factory-default  
settings.  
Product Information  
[Product Name] ..................Name of this model  
[Product ID]........................Product ID Number of the unit  
[OEM Software Version] ....Revision of the Microsoft Windows CE  
[Microsoft Windows CE]....Version of the Microsoft Windows CE  
6. USING THE TERMINAL PROPERTIES 61  
English  
Resetting to Default  
1. Click [Reset the terminal to factory-default property settings] check  
box.  
2. The “System Settings Change” dialog box is displayed.  
Click [Yes].  
3. “Terminal Properties” is displayed.  
Click [OK].  
“Terminal Setting Change” dialog box is displayed.  
Click [Yes] to restart the terminal. “WBT Setup Wizard” will be displayed after  
restarting the terminal.  
62 6. USING THE TERMINAL PROPERTIES  
English  
6-2. Input Devices Settings  
Click the [Input] tab to modify keyboard, NumLock Key, mouse characteristics, and  
touch panel calibration.  
(530L/531L)  
(531LT-GR)  
Keyboard Settings  
[Keyboard]  
[Locale]...............................Selects a keyboard language.  
[NumLock Enable on Boot UP]  
...................................enables/cancel NumLock function on start-up.  
[Character Repeat]  
[Repeat delay] ....................Allows adjusting the amount of time that elapses  
before begins repeating when you hold down a key.  
[Repeat rate] ......................Allows adjusting the speed at which a character  
repeats when hold down a key.  
6. USING THE TERMINAL PROPERTIES 63  
English  
Mouse Settings  
Click [Properties...] to display the [Mouse Properties].  
[Button Configuration] .......Assigns the primary mouse button and the secondary  
mouse button.  
[Speed]................................Adjusts the speed at which the pointer moves on your  
screen.  
[Acceleration]......................Adjusts the speed the mouse pointer accelerates as you  
move the mouse.  
64 6. USING THE TERMINAL PROPERTIES  
English  
Touch Panel Properties (531LT-GR only)  
Click [Properties...] to display the “Touch panel Properties”.  
[Mouse Right Click Emulation]  
[Enable right click emulation]  
...................................Holding stylus for a fixed period of time emulates  
mouse right button click. Click the [Enable right click  
emulation] check box , set a holding time, and adjust  
holding sensitivity.  
6. USING THE TERMINAL PROPERTIES 65  
English  
[Calibration]  
This enables to recalibrate the touch panel.  
Click [Recalibrate] to show the “Touch Panel calibration”.  
Five targets are displayed on the touch panel. Press the targets with a stylus or a  
fingertip to locate the center of the touch panel. If you accidentally touched the  
screen in the wrong spot during calibration, you will distort the touch panel  
calibration.  
“Calibration measured” window is displayed when you finished.  
66 6. USING THE TERMINAL PROPERTIES  
English  
Click [Enter] key to accept the settings.  
Click [OK] to return to the “Terminal Properties” and save the settings.  
Click [OK] to close “Terminal Properties” and save the adjustments.  
The “Terminal Settings change” dialog box will be displayed when the [Locale:],  
[Repeat delay:], and [Repeat rate:] are changed.  
Click [Yes] and restart the eClient.  
NOTE  
• Changing the Double-click speed, and Double-click width and height  
When you have difficulty with double-clicking on the touch panel with a stylus (or a  
fingertip):  
[Double-click speed]  
1) Click Window’s [Start] and select [Settings] - [Control Panel].  
2) Double-click [Mouse] and adjust the speed at [Double-click speed].  
[Double-click width and height]  
1) Click Window’s [Start] and select [Run…].  
2) Type ‘RegEdit.exe’ on [Name] and click [OK].  
3) [Registry Editor] is displayed. Select [HKEY_CURRENT_USER] - [Control  
Panel] - [Mouse].  
4) Double-click [DoubleClickHeight] and [DoubleClickWidth] and change the  
settings on [Value Data]. (Height and width will be increase as the value  
increase.)  
5) Close [Registry Editor].  
6) Logoff from the Server and re-logon to confirm the settings are effective. (If  
you do not logon to the Server after changing the settings, the change will not  
be effective.)  
6. USING THE TERMINAL PROPERTIES 67  
English  
6-3. Colors & Power Save Settings  
Click the [Display] tab to modify display parameters such as colors, screen saver, and  
power save.  
Resolution and Colors  
[Desktop Area and Colors]  
[Details] ..............................Adjusts the resolution and colors of the screen.  
Screen Saver  
[Screen Saver]  
[Enable Screen Saver]..........Click the [Enable Screen Saver] check box and set an  
idle period from 1 to 60 minutes before Screen Saver  
starts in minutes. Once the Screen Saver starts, the  
backlight is turned off.  
[Enable Power Save] ...........Interacts with [Screen Saver] and shift the state of the  
monitor into the power save mode. (The power  
consumption is lower than 10 W in the power save  
mode.)  
Click the [Enable Power save] check box and select an  
interval (from 0 to 60 minutes) between the time when  
the Screen Saver starts and when the unit shifts into  
[Power Saver].  
68 6. USING THE TERMINAL PROPERTIES  
English  
Brightness  
[Contrast/Brightness]  
[Settings].............................Enables to adjust the brightness of the screen.  
[Enable Contrast/Brightness control from Keyboard]  
Enables to adjust the brightness/contrast from a  
Keyboard.  
• [Alt] key and [+] key: The brightness of the screen  
increases.  
• [Alt] key and [-] key: The brightness of the screen  
decreases.  
Click [OK] to close “Terminal Properties” and save the adjustments.  
The “Terminal Settings change” dialog box will be displayed to restart the terminal and  
activate the adjustments when the [Details], [Wait] period of [Screen Saver], or [Enable  
Contrast/Brightness control from Keyboard] of [Brightness/Contrast] is changed.  
Click [Yes] to restart the unit.  
NOTE  
• Do your part to conserve energy, turn off the unit when you are finished using it.  
Complete energy use can only be accomplished by disconnecting the unit's power  
supply cord from the plug receptacle.  
6. USING THE TERMINAL PROPERTIES 69  
English  
6-4. Network Settings  
Click [Network] tab to set network information for the eClient.  
NOTE  
• All settings shown here are previously adjusted on the “WBT Setup Wizard”.  
• Please set the properties depending on the eClient connection settings.  
[Use PPP connection or another network adapter]  
...................................Click to use a modem connection to the WTS.  
(531L/531LT-GR only)  
To connect to the WTS with a LAN network, set the following.  
[Obtain an IP address from a DHCP server]  
...................................This allows the user to receive IP information from a  
DHCP service automatically. The DHCP service of a  
server must be in operation to receive the information.  
[Specify an IP address.] .......If not using a DHCP service, please select this and  
enter the information shown below.  
[IP address] .........................Type the eClient IP address.  
[Subnet Mask].....................Type the subnet mask.  
[Gateway] ...........................Type the Gateway IP address.  
[Terminal Name] ................Type a name to recognize this unit from others on the  
network (only in use of the RDP protocol).  
70 6. USING THE TERMINAL PROPERTIES  
English  
[DHCP Options...]..............Click this to receive essential information about the  
eClient from the DHCP server every time the eClient is  
turned on. Refer to “Practical Setup” on page 87 for  
details.  
[Advanced Network...] .......Allows setting for DNS/WINS service. A DNS/WINS  
server is required for the setting.  
[Enable DNS]......................Click the check box and type default domain name  
and IP address of the DNS server.  
[Enable WINS] ...................Click the check box and type IP address of the WINS  
server.  
Click [OK] to finish and return to the “Terminal Properties” dialog box.  
Click [OK] to show the [Terminal Settings Change] dialog box.  
Click [Yes] to restart the eClient.  
6. USING THE TERMINAL PROPERTIES 71  
English  
NOTE  
• The [Terminal Settings Change] dialog box will not be displayed when [Terminal  
Name], [DHCP Options], and [Advanced Network…] are changed, though the unit  
needs to be restarted to set the adjustment effective.  
72 6. USING THE TERMINAL PROPERTIES  
English  
6-5. Printer Settings  
Click [Printers] tab.  
You can add, delete and change the settings of the printer in this section.  
NOTE  
• The eClient supports a LPT1 port.  
• Use a RDP protocol to set the printer's adjustment. If you are using the ICA  
protocol, please refer to the instruction manual of the Citrix MetaFrame.  
6. USING THE TERMINAL PROPERTIES 73  
English  
Adding another printer settings  
This enables to add a printer when no printer is connected to the LPT1 port.  
1. Select LPT1 and click [Add].  
2. “Printer Properties” dialog box is displayed.  
[Friendly Name]..................Name the printer or use the indicated name. (Some  
programs do not support server and printer name  
combinations of more than 31 characters.)  
• When your printer is listed  
[Manufactures] / [Printers]  
...................................Select the manufacturer and model of your printer.  
• When your printer is not listed  
[User Defined].....................Click the check box.  
[Model Name] ....................Type the model and manufacturer of your printer.  
[Make this the default printer]  
...................................Click the check box to set the printer as the default  
printer.  
Click [OK] to return to the “Terminal Properties” dialog box.  
Click [OK] to save the settings and close the “Terminal Properties” dialog box.  
Deleting a printer settings  
This enables to delete printer settings when a printer is connected to the LPT1 port.  
1. Select LPT1 and click [Delete].  
2. “Delete Printer” dialog box is displayed.  
Click [Yes] to delete the settings of the printer.  
74 6. USING THE TERMINAL PROPERTIES  
English  
Modifying the settings  
This enables to delete printer settings when a printer is connected to the LPT1 port.  
1. Select LPT1 and click [Properties...].  
2. “Printer Properties” dialog box is displayed.  
Change the settings as needed.  
[Friendly Name]..................Changes the printer's name. (If you are naming the  
printer, the name combination must be 31 character or  
less.)  
• When your printer is listed  
[Manufactures] / [Printers]  
...................................Select the manufacturer and model of your printer.  
• When your printer is not listed  
[User Defined].....................Click the check box.  
[Model Name] ....................Type the model and manufacturer of your printer.  
[Make this the default printer]  
...................................Sets/cancels setting the printer as a default. (The  
eClient corresponds to only LPT1 port, and only one  
printer at a time can be installed. The installed printer  
will be always the default printer.)  
Click [OK] to return to the “Terminal Properties” dialog box.  
Click [OK] in the “Terminal Properties” dialog box to save the settings and close the  
“Terminal Properties” dialog box.  
6. USING THE TERMINAL PROPERTIES 75  
English  
6-6. Dial-Up (PPP) Connection Settings  
(531L/531LT-GR only)  
Click [PPP] tab to adjust the dial-up settings of eClient.  
The following details the installation of a dial-up connection to a WTS or a Web Server.  
(To use a dial-up connection requires an RAS server in operation.) Please see page 27  
for each setting.  
76 6. USING THE TERMINAL PROPERTIES  
English  
6-7. ICA Settings  
Click [ICA] tab to confirm information about Citrix ICA Client version and to change  
the settings when connecting to the Citrix Server with ICA protocol.  
NOTE  
• The ICA settings are effective only when the unit is connected to the WTS with ICA  
protocol. Also, the settings will affect all the settings with ICA protocol.  
Confirming Citrix ICA Client information  
[Client Software].................Version of the Citrix ICA Client.  
6. USING THE TERMINAL PROPERTIES 77  
English  
General Settings of the ICA Connection  
You can change the settings for the ICA Connection.  
1. Click [Settings...].  
2. “Global ICA Client Settings” dialog box is displayed.  
[Hotkeys] tab......................Enables to change the hotkeys when logging on to the  
Server. There are the hotkeys to control the eClient  
and the ones same as standard Windows hotkeys.  
Please refer to the instruction manual of the Citrix  
MetaFrame for details.  
NOTE  
• No hotkeys are set in the eClient in the factory default.  
[Preference] tab...................Select Colors sent from WTS, and type a client name  
to identify this unit on the network. The color setting  
change affects when adding a new connection.  
[Server Location] tab ..........Type the server location when the WTS is not on the  
same network (see page 42).  
This enables to change the server group name as well.  
78 6. USING THE TERMINAL PROPERTIES  
English  
[Firewall Settings] tab .........Change the settings of Firewall and SOCKS proxy  
server (see page 50).  
This setting change is displayed when adding a new  
connection.  
NOTE  
• If connecting a WTS through internet, the settings should be completed before  
the WTS is selected.  
• If you configure a default SOCKS proxy server, you must specify at least one  
WTS in the [Server Location] tab for a WTS and published application  
browsing to work.  
• If the Firewall settings are changed at the eClient, it is impossible to cancel the  
settings of a specific connection name. To change the Firewall settings, select  
a specific connection name and modify them or add a new connection name  
and change the settings.  
[PNLite] tab........................Register a public application name to a Terminal  
Connection Manager as a Connection Entry.  
Click [OK] to return to the “Terminal Properties” dialog box.  
Click [OK] of the “Terminal Properties” to close the “Terminal Properties” and save the  
settings.  
6. USING THE TERMINAL PROPERTIES 79  
English  
6-8. Product Information, Security & Updating  
Software  
Click [System] tab to confirm information about the eClient, to set the security, and to  
update firmware.  
Product Information  
[Software]  
[Microsoft Windows CE]  
...................................Microsoft Windows CE Version, Revision  
[Windows Terminal Server Client]  
...................................Window Terminal Server Client Revision  
[Boot software] ...................Boot Software Version of the eClient  
[Update...]...........................See page 83.  
[Hardware]  
[Serial Number] ..................Serial Number of the unit  
[Ethernet Address] ..............Ethernet address for the unit  
[Network] (Information adjusted for the connection to a WTS)  
[IP Address] ........................IP address of the unit  
[Subnet Mask].....................Subnet mask of the unit  
[Gateway] ...........................IP address of the Gateway machine if necessary  
80 6. USING THE TERMINAL PROPERTIES  
English  
Security Settings  
This enables settings on network information of the WTS invisible to prevent from  
undesirable change. When the security is active, the following settings become.  
• “Terminal Connection Manager”  
* [Configure] tab  
• “Terminal Properties”  
* [General] tab... [Reset the terminal to factory - default settings]  
* [Network] tab  
* [Printers] tab  
* [PPP] tab  
* [ICA] tab  
* [System] tab... [Update...], [Security]  
PROCEDURE  
1. Click the [Security Enable] box.  
2. Click [Setting Password...].  
3. “Security Password” dialog box is displayed.  
[Password]..........................Enter the password.  
[Confirm password:]...........Enter the same password for confirmation  
Click [Ok] to return to the “Terminal Properties” dialog box.  
Click [OK] to save the settings and close the “Terminal Properties” dialog box.  
6. USING THE TERMINAL PROPERTIES 81  
English  
CANCELING SETTINGS  
1. Display “Terminal Connection Manager”.  
2. Press [Ctrl], [A], and [F2] at the same time.  
3. “Enter Security Password” dialog box is displayed.  
[Password:] .........................Enter the password  
Click [OK] on [Enter Security Password] when finished.  
4. All settings in the “Terminal Properties” will be active.  
Click the [Security Enable] check box on the [System] tab and remove the check  
mark.  
Click [OK] on the “Terminal Properties” to save the settings and close the “Terminal  
Properties”. Security becomes canceled.  
Administration Console  
Assign the eClient a server with the Network Administrator, utility software for eClient.  
Other servers with the Network Administrator will not be able to control the eClient  
after setting the administration console.  
[Administration Console]....assign an IP address of a server with the Network  
Administrator.  
82 6. USING THE TERMINAL PROPERTIES  
English  
Software Updating  
You can update the built-in software.  
NOTE  
• Before updating, please complete the following:  
* Copy the update file (*.bin) to the accessible file folder of the FTP Server.  
* If the WTS is connected with LAN, close all the connections to the FTP Server.  
* Make a dial-up connection if it is adopted to connect the WTS. Software Updating  
is not available if a dial-in is adopted to connect the WTS.  
1. Click the [Update...] of [Software].  
The following message appears.  
Obey the instruction of the message completely and do not turn off the unit while  
updating.  
Click [Yes] to continue.  
6. USING THE TERMINAL PROPERTIES 83  
English  
2. The “Software Update” dialog box appears.  
[Server:] .............................Type IP address or full domain name of the FTP  
Server.  
[User Name:].......................Type the user name to connect the FTP Server.  
[Password:] .........................Type the password for the user name to connect the  
FTP Server.  
[File Name:]........................Type the folder and copied file name located in the  
FTP Server.  
<Example>  
Type the file name as indicated below if the file is in  
the “update folder” in the “software folder”:  
\software\update\*.bin  
84 6. USING THE TERMINAL PROPERTIES  
English  
NOTE  
• Clicking the "Execute automatic software update." check box will automatically  
consult the update file in the location indicated in the "Software Update" dialog  
box each time turning on the unit. If the update file consulted is newer, the  
software will be updated automatically while displaying the following dialog  
box. When updating the software, please set the following;  
(This function is not available for a modem connection. Please do not click the  
check box.)  
* Keep the keyboard and the mouse connected. (Operate with the keyboard  
and the mouse if failed to update.)  
* Click [Save Settings] to save settings.  
• Click [Save Settings] if using the same settings for the next update.  
* After inputting information, click [Save Setting] if using the “Automatic  
Update" function.  
3. Preventing from update failure, check if the settings are correct and  
the network environment is suitable.  
Click [Network Test].  
If the settings are correct, the following message is displayed.  
Click [OK].  
4. Click [Download].  
The following message is displayed when you successfully download the software.  
Click [OK] and restart the eClient.  
6. USING THE TERMINAL PROPERTIES 85  
English  
NOTE  
• Failing to download results in program's returning to the "Software Update"  
dialog box.  
* In case of returning to the "Software Update" dialog box, confirm such as  
network settings and redo the [Settings] before clicking [Download].  
* In case of retry dialog box is displayed, confirm connection or network  
settings by following the message, and click [Retry]. If the setting still fails,  
click [Cancel] to automatically restore the original software and restart the  
unit. the unit restarts and resets the update settings. Set the "Software  
Update" settings once again and download the software from the FTP  
Server. Do not turn off the unit when this dialog box is displayed until all the  
process is completed. The eClient will not restart correctly.  
86 6. USING THE TERMINAL PROPERTIES  
English  
7. PRACTICAL SETUP  
By utilizing the DHCP Option function of the DHCP Server, necessary information is  
supplied by the DHCP Server, and each setting is automatically set every time the unit is  
turned on.  
The following information can be obtained by the eClient.  
• WTS/Web Server Connection Settings  
• Automatic Software Update  
• Security Settings  
• Administration Console Setting  
NOTE  
• For DHCP Option settings, confirm the following:  
* The eClient is connected to the WTS/Web server through built-in LAN.  
* A DHCP Server is used for obtaining the IP address.  
• If you need to change the following settings from the defaults, please change them  
before using the DHCP option function.  
(information not given by using the DHCP option)  
Items  
Default Settings  
English (United States)  
Enable  
Input Tab Locale (Input Language)  
NumLock Enable on Boot UP  
Button Configuration  
Right-Handed  
Enable  
Enable right click emulation  
(531LT-GR)  
Holding time (531LT-GR)  
3 seconds  
Display  
Tab  
Desktop area and color  
Enable Screen Saver / Wait  
Enable Power Save / Wait  
Contrast/Brightness  
1024 x 768 256 Colors  
Enable / 5 Minutes  
Enable / 1 Minute  
Maximum  
[Enable Contrast/Brightness  
control from Keyboard]  
Enable  
Printer  
Tab  
Printer Settings  
No printer connected  
ICA Tab  
Hotkeys  
Disable  
Colors  
256 colors  
Client Name  
eClient******(Last 6 digits of the  
Mac address)  
Server Location  
Firewall Settings  
Automatically Found  
Disabled  
7. PRACTICAL SETUP 87  
English  
DHCP Server Settings  
Please open DHCP settings to configure each DHCP Option as follows.  
[Key]...................................Set the value as “EIZO”. (The eClient will not accept  
any value but “EIZO”.)  
[Server] ...............................Type an IP address of the Server installing an update  
file and a registry file of the eClient.  
[User Name]........................Type the user name to logon to the FTP Server.  
[Password] ..........................Type the password for the user name.  
[Automatic Connection] .....Enable/unable an automatic connection.  
[File Name].........................Type the file name to update the software of the  
eClient.  
[Security Setting].................Enable/unable the security settings.  
[Administration Console]....Type the IP address of the Server where Network  
Administrator (eClient utility software) is installed.  
88 7. PRACTICAL SETUP  
English  
NOTE  
• Making a Registry File to Connect to a WTS/Web Server.  
Please refer to the example below, make a registry file, and save it in Unicode  
format. Please change the italic bold phrases as necessary.  
- ConnectionName  
: Type the connection name in the “Terminal Connection Manager”.  
- TerminalServerAddress  
: Type the IP address or the full domain name of the WTS.  
- URL  
: Type the URL of the Web Server. (Including “http://”.)  
Registry file ..................................................................................... Value  
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\WBT]......  
"SetupWizardEnabled"=dword:0..................... Specifies whether starting up “WBT  
Setup Wizard” or not. (Fixed to  
“0”)  
(RDP Connection)  
Registry file ..................................................................................... Value  
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\WBT\Clients\  
Registration\RDP\Connections\ConnectionName]  
"DeleteCmdLineArgs"="/d ConnectionName".......... Command argument to delete  
connection information  
"DeleteExe"="TSConMan"........................... Fixed – command (an executable  
file) to delete connection  
information.  
"PropertiesCmdLineArgs"="/e ConnectionName"...... Command argument to change  
connection information.  
"PropertiesExe"="TSConMan"....................... Fixed – Command (executable file)  
to change connection information  
"StartCmdLineArgs"=""ConnectionName""............ Command argument to connect to a  
WTS  
"StartExe"="mstsc.exe"........................... Fixed – Command (executable file)  
to connect to a WTS  
"Description"="ConnectionName"................... Name displayed on the Connection  
Manager  
[HKEY_CURRENT_USER\Software\Microsoft\Terminal Server Client\ConnectionName]  
"Full Address"="TerminalServerAddress"........... IP address or full domain name of  
the WTS  
(ICA Connection)  
Registry file ..................................................................................... Value  
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\WBT\Clients\ Registration\ICA\Global\WFClient]  
"Version"="2".................................... Event for use of ICA protocol.  
(Fixed to “2”)  
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\WBT\Clients\Registration\ICA\Connections\  
ConnectionName]  
"DeleteCmdLineArgs"="/D:ConnectionName".......... Command argument to delete  
connection information  
"DeleteExe"="CEICAMGR"........................... Fixed – command (an executable  
file) to delete connection  
information.  
"PropertiesCmdLineArgs"="/P:ConnectionName"...... Command argument to change  
connection information.  
"PropertiesExe"="CEICAMGR"....................... Fixed – Command (executable file)  
to change connection information  
7. PRACTICAL SETUP 89  
English  
"StartCmdLineArgs"="/L "ConnectionName""......... Command argument to connect to a  
WTS  
"StartExe"="WFICACE"............................. Fixed – Command (executable file)  
to connect to a WTS  
"ScreenPercent"="100"............................ Fixed – Assign the ratio of the  
eClient screen to the displayed  
Window of the WTS.  
"Description"="ConnectionName"................... Name displayed on the Connection  
Manager  
"Address"="TerminalServerAddress"................ IP address or full domain name of  
the Meta Frame Server  
(Web Connection)  
Registry  
Value  
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\WBT]  
"SetupWizardEnabled"=dword:0..................... Specifies whether starting up “WBT  
Setup Wizard” or not. (0; not  
starting up, 1; starting up)  
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\WBT\Clients\  
Registration\Web\Connections\Web1]  
"StartCmdLineArgs"="URL"......................... Specifies the URL (including  
http://) to access.  
Registry  
Value  
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\WBT\Shell]  
"EnableAutoConnect"=dword:1...................... Specifies whether to  
enable/disable automatic  
connection. (0;disable, 1;enable)  
"ConnectionDefaultKey"="ConnectionName".......... Specify connection information  
name of the automatic connection.  
"ConnectionDefaultType"="RDP".................... Specify the type of the automatic  
connection. (The type is RDP,  
ICA, or Web.)  
*1 One entry name can be set at the Administration Console function.  
90 7. PRACTICAL SETUP  
English  
eClient Settings  
The eClient’s default setting is to enable DHCP Options. There is no need for extra  
settings. After initial setup, confirm the following:  
• [Use PPP connection or another network adapter]in the [Network] tab of “Terminal  
Properties” is selected.  
• Press “DHCP Option” on “Network” tab in the “Terminal Properties”. “DHCP  
Options” is displayed.  
[Enable DHCP Option] is selected, and code numbers assigned for the DHCP  
options.  
After completing the above, the eClient will automatically receive information such as  
an IP address from the DHCP Server every time the unit is turned on.  
NOTE  
• If the DHCP Option is used to setup the eClient for the first time, “Terminal  
Connection Manager” will appear because the unit automatically receives  
information from the DHCP Server. (“WBT Setup Wizard will not be displayed.)  
• If the DHCP Option is set once and needs to be canceled, please change the key of  
the DHCP Server. Even if changing the DHCP Option in the eClient, the DHCP  
Server will overwrite the option next time the unit is restarted, and the changes in  
the eClient will not be effective.  
7. PRACTICAL SETUP 91  
English  
8.TROUBLESHOOTING  
This page presents problem that can be corrected by the user. If a problem persists even  
after applying the suggested remedies, contact an EIZO dealer.  
Problems  
1. No picture is displayed on the screen. ꢀCheck if the power is OFF.  
ꢀCheck brightness setting. Minimum settings  
Points to check with possible solutions  
will cause screen to be blank.  
ꢀTry pressing a key on the keyboard, or clicking  
the mouse. (The monitor may be in a power  
saving mode.)  
2. The following messages appear on screen  
after the power is on:  
ꢀCheck if the cable of the keyboard is securely  
connected to the proper connector.  
(The operation automatically starts ꢀCheck if the cable of the mouse is securely  
up after the message disappears.)  
connected to the proper connector. (In use of a  
stylus or a finger as an input device, “No  
Mouse Connected!!” caution does not effect  
your operation.)  
* “WARNING  
No Keyboard Connected”  
* “WARNING  
No Mouse Connected”  
ꢀTurn off the power, and turn it on a few seconds  
later.  
3. Input devices (such as a keyboard, a  
mouse, a stylus) does not work properly.  
Solution on a mouse or a kyboard  
ꢀCheck if the cable of the keyboard or the mouse  
is securely connected.  
ꢀCheck if the cable of the keyboard or the mouse  
is connected to the proper connector.  
Solution on a stylus (531LT-GR)  
ꢀThe touch panel may not be calibrated properly.  
Please recalibrate the touch panel (see page 65).  
Solution on a keyboard, a mouse, and a stylus (531LT-  
GR)  
ꢀCheck if the network cable or the modem is  
securely connected. (To make sure the ethernet  
cable is connected securely, check if one of the  
indicators on the ethernet connector turns  
green.)  
92 8. TROUBLESHOOTING  
English  
Problems  
Points to check with possible solutions  
4. Afterimages appear on the screen.  
ꢀWhen the screen image has been changed after  
displaying the same image for a long period,  
afterimages may appear. Use the screen saver  
and avoid leaving the screen on all the time.  
5. The screen has defective pixels (e.g. ꢀThis is due to the characteristics of the panel  
slightly light or dark). itself, and not the failure.  
6. Finger prints appear on the screen. ꢀLeaving the white screen on may solve the  
problem.  
NOTE  
• Please do not connect and disconnect a keyboard or a mouse repeatedly while the  
eClient is in operation, as this may cause the eClient damage.  
8. TROUBLESHOOTING 93  
English  
9. CLEANING  
Periodic cleaning is recommended to keep the monitor looking new and to prolong its  
operation lifetime.  
NOTE  
• Never use thinner, benzene, alcohol (ethanol, methanol, or isopropyl alcohol),  
abrasive cleaners, or other strong solvents, as these may cause damage to the  
cabinet or LCD panel.  
Cabinet  
To remove stains, wipe the cabinet with a soft, lightly moistened cloth using a mild  
detergent. Do not spray wax or cleaner directly onto the cabinet.  
LCD Panel  
• The LCD surface can be cleaned with a soft cloth, such as cotton or lens paper.  
• If necessary, stubborn stains can be removed by moistening part of a cloth with water  
to enhance its cleaning power.  
94 9. CLEANING  
English  
Mouse  
If you find that the pointer on the screen doesn’t move smoothly, your mouse needs to  
be cleaned. Periodically clean the mouse for your operation.  
(1) Turn off the eClient.  
(2) Turn the mouse upside down and remove the mouse trackball cover. Press the  
cover towards “Open” while pulling the other side of the cover.  
Press  
(3) Remove the trackball.  
(4) Wipe the trackball with a soft cloth with neutral detergent.  
(5) Clean all the rollers, getting all the lint off of them.  
You can use a wet cotton swab to clean the rollers. Turn them to clean the  
entire roller.  
Rollers  
(6) Remove the dust inside of the mouse.  
(7) Put the trackball back into the mouse.  
(8) Close the mouse trackball cover.  
9. CLEANING 95  
English  
10. SPECIFICATIONS  
530L  
CPU and  
Memory  
CPU  
NEC VR4121-168, 168 MHz  
RAM; 32 MB, ROM;16 MB  
10BASE-T  
Memory  
LAN  
Display  
LCD Panel  
38 cm (15 inch) TFT color LCD panel  
Anti-Glare Hard Coating  
(Viewing Angle: Horizontal; 120°, Vertical; 140°)  
Dot Pitch  
0.297 mm x 0.297 mm  
1024 x 768  
Resolution  
Viewable  
Image Size  
304.1 mm (H) x 228.1 mm (V)  
(11.9" (H) x 8.9" (V))  
Display Color 256 / 65536 colors  
Complying Protocol  
Microsoft Remote Desktop (RDP)  
Citrix Independent Computing Architecture (ICA)  
Software  
Microsoft Windows CE Version 2.12  
Windows-based Terminal 1.5 Browser Add-on  
Citrix ICA Client 6.3  
Complying Software for  
Windows Terminal Server  
Microsoft Windows NT Server 4.0 Terminal Server  
Edition, Microsoft Windows 2000  
Server / Advanced Server / DataCenter Server,  
Citrix MetaFrame 1.8 / 1.8 + FR1 / XP  
Mouse  
PS/2 2 button Mouse  
Power Supply  
Power Consumption  
100-120/200-240 VAC ± 10 %, 50/60 Hz, 0.5/0.3 A  
Min: 30 W, Power saving mode: Less than 5 W  
10BASE-T (RJ-45) x 1  
Interface  
LAN  
Connector  
Keyboard,  
Mouse  
PS/2 (Mini DIN 6 pin) x 2  
Parallel  
IEEE1284 (D-Sub 25 pin) x 1  
Dimensions  
(With the tilt stand)  
396 mm (W) x 390 mm (H) x 164 mm (D)  
(15.6" (W) x 15.4" (H) x 6.5" (D))  
Weight  
5.0 kg (11.0 lbs.)  
(without the tilt stand  
3.6 kg (7.9 lbs.))  
Environmental Specifications Temperature  
Operating: 0°C to 35°C (32°F to 95°F)  
Storage: -20°C to 60°C (-4°F to 140°F)  
30 % to 80 % R.H. Non-condensing  
Humidity  
Certifications and Standards  
100 -120 VAC range  
TÜV/NRTL, c-TÜV, FCC class A, CB, TÜV Rheinland  
Ergonomics Approved, EPA ENERGY STAR® program,  
TCO’99  
200-240 VAC range  
CE, CB, TÜV Rheinland/GS, TÜV Rheinland/Ergonomic  
Approved, EPA ENERGY STAR® program, TCO’99  
96 10. SPECIFICATIONS  
English  
531L  
CPU and  
Memory  
CPU  
Memory  
LAN  
NEC VR4121-168, 168 MHz  
RAM; 32 MB, ROM;16 MB  
10BASE-T  
Display  
LCD Panel  
38 cm (15 inch) TFT color LCD panel  
Anti-Glare Hard Coating  
(Viewing Angle: Horizontal; 120°, Vertical; 140°)  
Dot Pitch  
0.297 mm x 0.297 mm  
1024 x 768 (768 x 1024)  
Resolution  
Viewable  
Image Size  
304.1 mm (H) x 228.1 mm (V)  
(11.9" (H) x 8.9" (V))  
Display Color 256 / 65536 colors  
Complying Protocol  
Microsoft Remote Desktop (RDP)  
Citrix Independent Computing Architecture (ICA)  
Software  
Microsoft Windows CE Version 2.12  
Windows-based Terminal 1.5 Browser Add-on  
Citrix ICA Client 6.3  
Complying Software for  
Windows Terminal Server  
Microsoft Windows NT Server 4.0 Terminal Server  
Edition, Microsoft Windows 2000  
Server / Advanced Server / DataCenter Server,  
Citrix MetaFrame 1.8 / 1.8 + FR1 / XP  
Mouse  
PS/2 2 button Mouse  
Power Supply  
Power Consumption  
100-120/200-240 VAC ± 10 %, 50/60 Hz, 0.5/0.3 A  
Min: 30 W, Power saving mode: Less than 5 W  
10BASE-T (RJ-45) x 1  
Interface  
LAN  
Connector  
Keyboard,  
Mouse  
PS/2 (Mini DIN 6 pin) x 2  
Parallel  
IEEE1284 (D-Sub 25 pin) x 1  
RS-232C (D-Sub 9 pin) x 1  
Serial Port  
Dimensions  
(With the tilt stand)  
396 mm (W) x 390 mm (H) x 164 mm (D)  
(15.6" (W) x 15.4" (H) x 6.5" (D))  
Weight  
5.0 kg (11.0 lbs.)  
(without the tilt stand  
3.6 kg (7.9 lbs.))  
Environmental Specifications Temperature  
Operating: 0°C to 35°C (32°F to 95°F)  
Storage: -20°C to 60°C (-4°F to 140°F)  
30 % to 80 % R.H. Non-condensing  
Humidity  
Certifications and Standards  
100 -120 VAC range  
TÜV/NRTL, c-TÜV, FCC class A, CB, TÜV Rheinland  
Ergonomics Approved, EPA ENERGY STAR® program,  
TCO’99  
200-240 VAC range  
CE, CB, TÜV Rheinland/GS, TÜV Rheinland/Ergonomic  
Approved, EPA ENERGY STAR® program, TCO’99  
10. SPECIFICATIONS 97  
English  
531LT-GR  
CPU and  
Memory  
CPU  
Memory  
LAN  
NEC VR4121-168, 168 MHz  
RAM; 32 MB, ROM;16 MB  
10BASE-T  
Display  
LCD Panel  
38 cm (15 inch) TFT color LCD panel  
Anti-Glare Hard Coating  
(Viewing Angle: Horizontal; 120°, Vertical; 140°)  
Dot Pitch  
0.297 mm x 0.297 mm  
1024 x 768 (768 x 1024)  
Resolution  
Viewable  
Image Size  
304.1 mm (H) x 228.1 mm (V)  
(11.9" (H) x 8.9" (V))  
Display Color 256 / 65536 colors  
Detective Method; Analog Resistive Type  
Touch Panel  
Surface Treatment; Non-Glare Coating  
Complying Protocol  
Software  
Microsoft Remote Desktop (RDP)  
Citrix Independent Computing Architecture (ICA)  
Microsoft Windows CE Version 2.12  
Windows-based Terminal 1.5 Browser Add-on  
Citrix ICA Client 6.3  
Complying Software for  
Windows Terminal Server  
Microsoft Windows NT Server 4.0 Terminal Server  
Edition, Microsoft Windows 2000  
Server / Advanced Server / DataCenter Server,  
Citrix MetaFrame 1.8 / 1.8 + FR1 / XP  
Mouse  
PS/2 2 button Mouse  
Power Supply  
Power Consumption  
100-120/200-240 VAC ± 10 %, 50/60 Hz, 0.5/0.3 A  
Min: 30 W, Power saving mode: Less than 5 W  
10BASE-T (RJ-45) x 1  
Interface  
LAN  
Connector  
Keyboard,  
Mouse  
PS/2 (Mini DIN 6 pin) x 2  
Parallel  
IEEE1284 (D-Sub 25 pin) x 1  
RS-232C (D-Sub 9 pin) x 1  
Serial Port  
Dimensions  
(With the tilt stand)  
396 mm (W) x 390 mm (H) x 164 mm (D)  
(15.6" (W) x 15.4" (H) x 6.5" (D))  
Weight  
5.0 kg (11.0 lbs.)  
(without the tilt stand  
3.6 kg (7.9 lbs.))  
Environmental Specifications Temperature  
Operating: 0°C to 35°C (32°F to 95°F)  
Storage: -20°C to 60°C (-4°F to 140°F)  
30 % to 80 % R.H. Non-condensing  
Humidity  
Certifications and Standards  
100 -120 VAC range  
TÜV/NRTL, c-TÜV, FCC class A, CB, EPA ENERGY  
STAR® program  
200-240 VAC range  
CE, CB, TÜV Rheinland/GS, EPA ENERGY STAR®  
program  
98 10. SPECIFICATIONS  
English  
Dimensions  
530L  
mm (inches)  
531L  
531LT-GR  
10. SPECIFICATIONS 99  
English  
11. REFERENCE  
11-1. Attaching an Arm Stand  
The eClient can be used with an arm stand by removing the tilt stand and attaching the  
arm stand to the terminal.  
NOTE  
• Use an arm stand that satisfies the following.  
- When using the eClient with an arm stand, the arm stand must be VESA  
approved :  
Use an arm stand with a 75 mm x 75 mm hole spacing on the arm mounting pad.  
Use an arm stand that is able to support an object weighing 8.0 kg.  
A GS approved arm stand.  
- Use an arm stand with sufficient stability (mechanical firmness) to support the  
weight of the monitor.  
- Use an arm stand remaining that position where it is manually moved.  
- Use an arm stand with the ability to tilt the monitor forward and backward.  
• Please connect cables after attaching an arm stand.  
Setup Procedure  
1. Lay the eClient down as shown below. Do not scratch the panel.  
2. Remove the stand by loosening the screws (M4 x 16 mm).  
100 11. REFERENCE  
English  
3. Attach an arm stand to the eClient securely.  
WARNING  
Install the unit securely when attaching to an arm stand.  
When attaching an arm stand, please refer to the user’s manual of  
the arm stand and install the unit securely with the enclosed  
screws. Not doing so may cause the unit to come unattached,  
which may result in injury or equipment damage. When the unit is  
dropped, please ask your dealer for advice. Do not continue using  
a damaged unit. Using a damaged unit may result in fire or electric  
shock.  
When reattaching the stand, please use the same screws (M4 x 16  
mm) and tighten them securely.  
Arm  
(2)  
(1)  
(4)  
(3)  
(1), (2), (3), (4): Enclosed Screws, M4 x 12 mm  
11. REFERENCE 101  
English  
INDEX  
A
I
ADDING & CHANGING A CONNETION  
NAME ...............................................34  
Administration Console............................82  
Application to Run..............................38, 46  
Attaching an Arm Stand.........................100  
Automatic Logon................................37, 47  
Autostart Connection ...............................55  
ICA ....................................................34, 40  
ICA Connection........................................54  
ICA Settings.............................................77  
IP address....................................16, 17, 36  
K
Keyboard..................................................11  
Keyboard Settings....................................63  
B
L
Brightness............................................6, 69  
Local Printer Setup ..................................20  
Logoff from the WTS................................59  
Logon & Logoff.........................................56  
Logon to a WTS.......................................56  
C
Calibration................................................65  
Citrix Server or Published Application  
Selection...........................................42  
Cleaning...................................................94  
Client Name .............................................78  
Colors.....................................19, 48, 68, 78  
Compress Data Stream ...........................49  
Connecting the eClient ............................10  
Connection Name..................36, 39, 46, 51  
Controls & Connectors...............................7  
M
Making a Registry File .............................89  
Mouse ........................................................6  
Mouse Right Click Emulation...................65  
Mouse Settings........................................64  
Multi Session............................................58  
N
D
Network Settings................................28, 70  
DHCP.................................................16, 70  
DHCP Options ...................................71, 87  
Dial-in Connection....................................27  
Dial-In Device...........................................44  
Dial-up Connection Settings ..............29, 76  
Dial-Up Connection settings ....................27  
Disconnect ...............................................60  
DNS .........................................................18  
Domain Name..........................................18  
O
Overview....................................................9  
P
Package Contents......................................6  
Portrait ........................................................6  
Power Indicator ..........................................7  
Printer Configuration Utility......................49  
Printer Settings ........................................73  
Product Information .................................80  
Program Neighborhood Lite.....................79  
Protocol..............................................35, 40  
E
Editing a Connection................................53  
Encryption Level ......................................49  
F
R
Firewall Settings.................................50, 79  
RAS..........................................................27  
RDP ...................................................34, 35  
Reference ..............................................100  
Resetting to Default .................................62  
Resolution..........................................19, 68  
G
General Information .................................61  
Global ICA Client Settings .......................78  
H
Hotkeys ....................................................78  
102 INDEX  
English  
S
Screen Saver ...........................................68  
Security Settings......................................81  
Serial Port..................................................6  
Server Location........................................78  
Setting up.................................................10  
Software Updating ...................................83  
Specifications...........................................96  
Specify an IP Address .............................17  
Specify Connection Type .........................41  
SpeedScreen...........................................49  
Stylus .........................................................6  
Subnet Mask............................................17  
T
TCO ...........................................................6  
Terminal Connection Manager...........39, 50  
Terminal Name...................................16, 70  
Terminal Properties............................30, 61  
Title for the ICA Connection.....................46  
Touch Panel Properties............................64  
Touch screen calibration .............................14  
Troubleshooting........................................92  
W
Windows Terminal Server (WTS)...............5  
WINS........................................................18  
WTS Connection Wizard .........................36  
INDEX 103  

Hanns G HG216DPO User Manual
Gateway FPD 1940 User Manual
Eizo TX D7 User Manual
Dell Axim X51 User Manual
Contec DIO 4 User Manual
Avsar Emaye San Tic A S DVD Copy User Manual
AT T HS8240 User Manual
AT T Four Handset Cordless Phone ATTCL82301 User Manual
Asus K8V F User Manual
AOC Computer Monitor 931SN User Manual