(877) TWO - LCDS
USER'S MANUAL
DoubleSight DS-309W
LCD MONITOR
For the latest updates and more information, visit our website at
Safety Precautions
Safety Precautions
30”Type - 2560 x 1600 @60Hz
4
5
Safety Precautions
Safety Instructions
Available Temperature & Humidity
No
1
Test Item
Condition
Ta= 60°C 240h
High temperature storage test
Low temperature storage test
High temperature operation test
Low temperature operation test
2
Ta= -20°C 240h
3
Ta= 40°C 50%RH 240h
4
Ta= 0°C
240h
Wave form : random
Vibration level : 1.0G RMS
Bandwidth : 10-300Hz
Duration : X,Y,Z, 10 min
Vibration test
(non-operating)
5
One time each direction
Shock level : 100Grms
Shock test
(non-operating)
Waveform : half sine wave, 2ms
Direction : ±X, ±Y, ±Z
One time each direction
6
7
Altitude
Operating
Storage / Shipment
0 - 10,000 feet(3,048m)
0 - 40,000 feet(12,192m)
For dot defect [dead pixel] of LCD
TFT-LCD produced by using high-end semiconductor technology with precision of 99.9% above is used for
this monitor.
However the pixels of R.G.B. & White color seem to be right sometimes or some of black pixels could be seen
on the LCD. This is not from bad quality or functional problem and you can use it without any problem.
Supported resolution mode table
No
1
Resolution
No
6
Resolution
2560 X 1600 @ 60Hz (WQHD)
1920 X 1200 @ 60Hz (WUXGA)
1920 X 1080 @ 60Hz (WXGA+)
1600 X 900 @ 60Hz (WXGA)
1360 X 768 @ 60Hz~75Hz (SXGA)
1280 X 1024 @ 60Hz~75Hz (XGA)
1024 X 768 @ 60Hz~75Hz (SVGA)
800 X 600 @ 60Hz~75Hz (VGA)
640 X 480 @ 60Hz~75Hz (VGA)
2
7
3
8
4
9
5
6
7
Adjusting the Monitor Screen
Packing Contents
Base Function
Packing Contents
Please make sure the following items are included with your monitor.
If any items are missing, contact your dealer.
LCD Monitor
Power Cord
AC Adaptor
Dual Link DVI Cable
8
9
Connecting to PC
Troubleshooting
Computer Connection
Troubleshooting
If you encounter a problem with your monitor please review these troubleshooting tips.
If the problem persists please contact your monitor dealer or DoubleSight customer service for additional
assistance.
No image on the monitor
- Check whether a graphic card is correctly inserted into the slot.
- Check whether the power of the PC and the monitor is on.
- Check whether a graphic card or mode is set appropriately on the PC.
- Check whether DVI cable pins are not inserted or bent.
No Power
- Check whether the power cord is correctly inserted and reconnect if necessary.
- Pull out the power cord from wall outlet and reconnect in 1 ~ 2 minutes.
- Check whether DVI cable is connected to the monitor and the PC.
- Check whether the PC is in power saving made and attempt to operate keyboard and mouse.
Unstable or unfocused image or trembling
- Check whether DVI cable is connected to the monitor and the PC.
- If the PC’s display mode is changed, the screen needs readjusting. So check the display mode.
VGA
•
If only one connections is required a DVI connection is recommended if available
10
11
Dimensions
Specifications
Dimensions (mm)
Speciꢀcations
Dimensions, apparent design and speciꢀcations are subject to change without any prior notice
for the performance improvement.
Product Name
30” Wide TFT-LCD Monitor
692.15
76.2
Panel Type
TFT
Screen Size
Visible Screen Area
Resolution
29.55” (75.05cm) Diagonal
614.28mm(H) x 400.8mm(V)
2,560(H) X 1,600(V)
0.2331mm x 0.2331mm
1.07 Billion Colors, 10 bit with A-FRC
1000 : 1
Pixel Pitch
LCD Panel
Color Depth
Contrast Ratio
Brightness
370 cd /㎡
Viewing Angle
Response Time
Horizontal 178ꢀ, Vertical 178ꢀ
6ms (GTG)
Power Consumption
In-Operation
DPMS /OFF
< 120W
> 1.2W
Energy Saving Mode
Power
VESA DPMS
AC 100V~240V, 50~60Hz
DC 24V / 5.0A
349.25
Adaptor Input
Adaptor Output
180.00
Dual Link DVI, D-SUB, DP, Audio In, Audio Out, HDMI
Dual link DVI cable, VGA Cable, AC Adapter,
Power Cord
Video Interface
Accessories
Product Weight: approximately 22.5lbs
12
13
Connecting to PC
Adjusting the Monitor Screen
Connecting to PC
How to adjust monitors
OSD Functions Description
To connect the monitor to the PC, please follow these instructions:
1. Connect DVI cable to the PC. Tighten all the screws.
OSD Menus
2. Connect DVI cable to the DVI connector on the back of the monitor. Tighten all the screws.
3. Connect one end of the power cord to the AC adaptor and the other end to the AC power outlet.
4. Connect DC adaptor cable to the power input connector on the back of the monitor.
5. Turn On the monitor and PC.
6. Adjusting display resolution of PC
- Resolution : 2,560 X 1,600
- Refresh Rate : 60 Hz
OSD Control
This monitor does support OSD Menu control function.
SELECT MENU VOL+ VOL- UP DOWN
①
②
③
④
⑤
Image Setting.
- Adjust screen’s Brightness, Sharpness and Color Temperature.
① : Input Source Select / OSD Sub Menu Select
②
③ : Volume Up & Down / OSD Menu Left & Right
④ : OSD Menu Up & Down / Channel Up & Down
⑤
Display Setting.
- Adjust Aspect ratio, PIP mode/position/source, Transparency.
Audio Setting.
- Adjust Mute, Volume and Output.
PC.
③ VOL+, VOL- : Controls the speaker volume
④ DOWN : Switches Aspect Ratios(16:10 4:3)
- Adjust Display position automatically or manually.
④ UP : In VGA mode, Automaticaly adjust optimal settings of monitor
Setup.
- Adjust Language, OSD Menu time, OSD position and OSD transparency,
and Factory Reset.
14
15
Adjusting the Monitor Screen
Adjusting the Monitor Screen
How to adjust monitors
How to adjust monitors
OSD Functions Description
OSD Functions Description
Image Settings
Audio Setting
Brightness
- Adjust the brightness, Press (VOL+, VOL-)
buttons to adjust the level of these settings.
Mute
- Mute speaker on / off
Contrast
Volume
- Adjust the image contrast, Press (VOL+, VOL-)
buttons to adjust the level of these settings.
- Adjust the sound volume of the speaker
Sharpness
- Adjust the image sharpness, Press (VOL+,
VOL-) buttons to adjust the level of these settings.
Output
- Adjust the output of headphones and speaker
Color Temp.
- Adjust the color temperature by choosing the
color temperature presets(6500K, 7500K, 9300K),
press (DOWN, UP) buttons to adjust colors.
Customize color temperature by choosing the
User option.
Display Settings
Auto Adjustment
- Automaticaly adjust optimal settings of monitor
Image Position
- Adjust the position of the display horizontaly and
verticaly.
Display Settings
Aspect Ratio
- Choose between the aspect ratios (16:10 or 4:3).
PIP Mode(Picture in Picture)
- Adjusts the screen size of the PIP window.
PIP Position
- Adjust the position of the PIP window.
Setup
Factory Reset
- Reset all user settings to factory preset
PIP Source
- Select the input source of the PIP window .
Language
- Select a language for OSD menu
Transparency
- Adjust the level of PIP window’s transparency .
OSD Timer
- Control display time on OSD window
Note:
Operating PIP mode under DVI and HDMI connection at the same time is not available.
OSD Position
- Adjust position of the OSD window on display
E.X: Main display as DVI and PIP display as HDMI connection or vice versa is not available.
Any other combination of connection than above are available.(E.X: DVI and VGA)
Transparency
- Adjust the level of OSD window’s transparency
16
17
Adjusting the Monitor Screen
Note
How to adjust monitors
OSD Functions Description
Source Selection
Source
- Scroll Up and Down to select the source and press VOL+ to select
18
19
DS-279W
27
DS-279W
20
21
22
23
|