Dell E1913S/E1913/E2213 Monitor User's Guide
Dell™ E1913S/E1913/E2213 Monitor User's Guide
Notes, Cautions, Warnings
NOTE: A NOTE indicates important information that helps you make better use of your computer.
CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
Information in this document is subject to change without notice.
© 2012 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.; Microsoft and Windows are either trademarks or registered trademarks of Microsoft Corporation in
the United States and/or other countries. ENERGY STAR is a registered trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has determined
that this product meets the ENERGY STAR guidelines for energy efficiency.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary
interest in trademarks and trade names other than its own.
Model E1913Sf/E1913Sc/E1913c/E2213c
April 2012 Rev. A00
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/index.htm[2012-3-19 16:21:58]
About Your Monitor: Dell E1913S/E1913/E2213 Monitor User's Guide
VGA Cable (attached to the monitor)
DVI Cable (Packing for E1913 and E2213 only)
Drivers and Documentation media
Quick Setup Guide
Product Information Guide
Product Features
The Dell™ E1913S/E1913/E2213 flat panel display has an active matrix, Thin-Film Transistor, Liquid Crystal Display. The monitor's features include:
E1913S: 48.3 cm (19.0 inches) viewable area display. 1280 x 1024 resolution, plus full-screen support for lower resolutions.
E1913: 48.3 cm (19.0 inches) viewable area display. 1440 x 900 resolution, plus full-screen support for lower resolutions.
E2213: 55.9 cm (22.0 inches) viewable area display. 1680 x 1050 resolution, plus full-screen support for lower resolutions.
Tilt adjustment capability.
Removable stand and Video Electronics Standards Association (VESA) 100 mm mounting holes for flexible mounting solutions.
Plug and play capability if supported by your system.
On-Screen Display (OSD) adjustments for ease of set-up and screen optimization.
Software and documentation media which includes an information file (INF), Image Color Matching File (ICM), and product documentation.
Dell Display Manager included (comes in the CD attached with the monitor).
Security lock slot.
Asset Management Capability.
ENERGY STAR compliant.
EPEAT™ Gold compliant.
RoHS compliant.
Halogen Reduced.
TCO Certified Display.
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/about.htm[2012-3-19 16:21:58]
About Your Monitor: Dell E1913S/E1913/E2213 Monitor User's Guide
Identifying Parts and Controls
Front View
Function buttons (For more information, see
1.
2. Power On/Off button (with LED indicator)
Back View
Label Description
VESA mounting holes (100 mm)
Use
1
To mount the monitor.
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/about.htm[2012-3-19 16:21:58]
About Your Monitor: Dell E1913S/E1913/E2213 Monitor User's Guide
2
3
4
5
Rating label
Power ratings and energy information.
Barcode serial number label
Security lock slot
Refer to this label if you need to contact Dell for technical support.
Use a security lock with the slot to help secure your monitor.
To attach the optional Dell Soundbar.
Dell soundbar mounting brackets
Side View
Right Side
Bottom View
E1913S:
E1913/E2213:
Label Description
Use
Label Description
Use
1
2
3
4
5
Regulatory label
AC power connector
DVI connector
Lists the regulatory approvals.
1
2
3
4
Regulatory label
AC power connector
VGA connector
Lists the regulatory approvals.
To connect the monitor power cable.
To connect your computer to the monitor using a VGA cable.
Lists the regulatory approvals.
To connect the monitor power cable.
To connect your computer to the monitor using a DVI cable.
To connect your computer to the monitor using a VGA cable.
Lists the regulatory approvals.
VGA connector
Regulatory label
Regulatory label
Monitor Specifications
The following sections give you information about the various power management modes and pin assignments for the various connectors of your monitor.
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/about.htm[2012-3-19 16:21:58]
About Your Monitor: Dell E1913S/E1913/E2213 Monitor User's Guide
Power Management Modes
If you have VESA's DPM compliance display card or software installed in your PC, the monitor automatically reduces its power consumption when not in use. This is referred to as Power Save Mode. If the computer detects
input from keyboard, mouse, or other input devices, the monitor automatically resumes functioning. The following table shows the power consumption and signaling of this automatic power saving feature:
E1913S:
VESA Modes
Horizontal Sync
Vertical Sync
Video
Power Indicator
Power Consumption
Normal operation
Active
Active
Active
Blue
23 W (Maximum)
18 W (Typical)
Active-off mode
Switch off
Inactive
-
Inactive
-
Blank
-
Amber
Off
Less than 0.5 W
Less than 0.5 W
E1913:
VESA Modes
Horizontal Sync
Vertical Sync
Video
Power Indicator
Power Consumption
Normal operation
Active
Active
Active
Blue
23 W (Maximum)
18 W(Typical)
Active-off mode
Switch off
Inactive
-
Inactive
-
Blank
-
Amber
Off
Less than 0.5 W
Less than 0.5 W
E2213:
VESA Modes
Horizontal Sync
Vertical Sync
Video
Power Indicator
Power Consumption
Normal operation
Active
Active
Active
Blue
24 W (Maximum)
19 W (Typical)
Active-off mode
Switch off
Inactive
-
Inactive
-
Blank
-
Amber
Off
Less than 0.5 W
Less than 0.5 W
The OSD will only function in the normal operation mode. When any button except power button is pressed in Active-off mode, the following messages will be displayed:
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/about.htm[2012-3-19 16:21:58]
About Your Monitor: Dell E1913S/E1913/E2213 Monitor User's Guide
NOTE: Dell E1913S/E1913/E2213 monitor is ENERGY STAR®-
compliance.
* Zero power consumption in OFF mode can only be achieved by disconnecting the main cable from the monitor.
** Maximum power consumption with max luminance and contrast.
Pin Assignments
15-pin D-Sub connector
Pin Number Monitor Side of the 15-pin Side Signal Cable
1
2
3
4
5
6
7
8
Video-Red
Video-Green
Video-Blue
GND
Self-test
GND-R
GND-G
GND-B
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/about.htm[2012-3-19 16:21:58]
About Your Monitor: Dell E1913S/E1913/E2213 Monitor User's Guide
9
DDC +5V
GND-sync
GND
10
11
12
13
14
15
DDC data
H-sync
V-sync
DDC clock
DVI Connector
Pin
Number
24-pin Side of the Connected Signal
Cable
1
2
3
4
5
TMDS RX2-
TMDS RX2+
TMDS Ground
Floating
Floating
6
DDC Clock
DDC Data
7
8
Floating
9
TMDS RX1-
TMDS RX1+
TMDS Ground
Floating
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Floating
+5 V power
Self test
Hot Plug Detect
TMDS RX0-
TMDS RX0+
TMDS Ground
Floating
Floating
TMDS Ground
TMDS Clock+
TMDS Clock-
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/about.htm[2012-3-19 16:21:58]
About Your Monitor: Dell E1913S/E1913/E2213 Monitor User's Guide
Plug and Play Capability
You can install the monitor in any Plug and Play compatible system. The monitor automatically provides the computer with its Extended Display Identification Data (EDID) using Display Data Channel (DDC) protocols so
that the system can configure itself and optimize the monitor settings. Most monitor installations are automatic. You can select different settings if required.
Flat Panel Specifications
Model number
Screen type
Panel Type
Dell E1913S monitor
Active matrix - TFT LCD
TN
Dell E1913 monitor
Active matrix - TFT LCD
TN
Dell E2213 monitor
Active matrix - TFT LCD
TN
48.3 cm (19.0 inches) (19.0-inch
viewable image size)
48.3 cm (19.0 inches) (19.0-inch wide
viewable image size)
55.9 cm (22.0 inches) (22.0-inch wide
viewable image size)
Screen dimensions
Preset display area:
Horizontal
376.3 mm (14.81 inches)
301.1 mm (11.85 inches)
408.2 mm (16.07 inches)
255.2 mm (10.05 inches)
473.8 mm (18.65 inches)
296.1 mm (11.66 inches)
Vertical
Pixel pitch
0.294 mm
0.284 mm
0.282 mm
Viewing angle
Horizontal
Vertical
170 ° typical
160 ° typical
170 ° typical
160 ° typical
170 ° typical
160 ° typical
Luminance output
Contrast ratio
Faceplate coating
Backlight
250 cd/m² (typical)
250 cd/m² (typical)
250 cd/m² (typical)
1000 to 1 (typical)
1000 to 1 (typical)
1000 to 1 (typical)
Antiglare with hard-coating 3H
LED light bar system
5 ms typical (black to white)
16.7 mil colors
Antiglare with hard-coating 3H
LED light bar system
5 ms typical (black to white)
16.7 mil colors
Antiglare with hard-coating 3H
LED light bar system
5 ms typical (black to white)
16.7 mil colors
Response Time
Color Depth
Color Gamut
83 % (typical) **
83 % (typical) **
83 % (typical) **
* Based on estimation.
** [E1913S/E1913/E2213] color gamut (typical) is based on CIE1976 (82 %) and CIE1931 (72 %) test standards.
Resolution Specifications
Model number
Dell E1913S monitor
Dell E1913 monitor
Dell E2213 monitor
Scan range
Horizontal
Vertical
30 kHz to 81 kHz (automatic)
30 kHz to 83 kHz (automatic)
30 kHz to 83 kHz (automatic)
56 Hz to 76 Hz (automatic)
56 Hz to 75 Hz (automatic)
56 Hz to 75 Hz (automatic)
Maximum preset resolution
1280 x 1024 at 60 Hz
1440 x 900 at 60 Hz
1680 x 1050 at 60 Hz
Electrical Specifications
Model number
Dell E1913S/E1913/E2213 monitor
Analog RGB: 0.7 Volts +/- 5 %, 75 ohm input
impedance
DVI-D: Single link maximum data rate including
8b/10b overhead is 4.95 Gbit/s @ 165 MHz base
Video input signals
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/about.htm[2012-3-19 16:21:58]
About Your Monitor: Dell E1913S/E1913/E2213 Monitor User's Guide
on four TMDS pairs, 100 ohm input
impedence.(For E1913 and E2213 only)
Separate horizontal and vertical synchronizations,
polarity-free TTL level, SOG (Composite SYNC on
green)
Synchronization input signals
100 VAC to 240 VAC/50 Hz or 60 Hz + 3 Hz/1.5 A
(Max.)
AC input voltage / frequency / current
Inrush current
120 V: 30 A (Max.)
240 V: 60 A (Max.)
Preset Display Modes
The following table lists the preset modes for which Dell guarantees image size and centering:
E1913S:
Display Mode
Horizontal Frequency
(kHz)
Vertical Frequency
(Hz)
Pixel Clock (MHz)
Sync Polarity
(Horizontal/Vertical)
VESA, 720 x 400
31.5
31.5
37.5
37.9
46.9
48.4
60.0
67.5
64.0
80.0
70.1
59.9
75.0
60.3
75.0
60.0
75.0
75.0
60.0
75.0
28.3
25.2
31.5
40.0
49.5
65.0
78.8
108.0
108.0
135.0
-/+
-/-
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 x 1024
VESA, 1280 x 1024
-/-
+/+
+/+
-/-
+/+
+/+
+/+
+/+
E1913:
Display Mode
Horizontal Frequency
(kHz)
Vertical Frequency
(Hz)
Pixel Clock (MHz)
Sync Polarity
(Horizontal/Vertical)
VESA, 720 x 400
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 x 1024
VESA, 1280 x 1024
VESA, 1280 x 800
VESA, 1440 x 900
VESA, 1440 x 900
31.5
31.5
37.5
37.9
46.9
48.4
60.0
67.5
64.0
80.0
49.7
55.9
70.6
70.1
59.9
75.0
60.3
75.0
60.0
75.0
75.0
60.0
75.0
59.8
59.9
75.0
28.3
25.2
-/+
-/-
31.5
-/-
40.0
+/+
+/+
-/-
49.5
65.0
78.8
+/+
+/+
+/+
+/+
-/+
-/+
-/+
108.0
108.0
135.0
83.5
106.5
136.8
E2213:
Display Mode
Horizontal Frequency
(kHz)
Vertical Frequency
(Hz)
Pixel Clock (MHz)
Sync Polarity
(Horizontal/Vertical)
VESA, 720 x 400
VESA, 640 x 480
VESA, 640 x 480
31.5
31.5
37.5
70.1
59.9
75.0
28.3
25.2
31.5
-/+
-/-
-/-
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/about.htm[2012-3-19 16:21:58]
About Your Monitor: Dell E1913S/E1913/E2213 Monitor User's Guide
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 x 1024
VESA, 1280 x 1024
VESA, 1680 x 1050
37.9
46.9
48.4
60.0
67.5
64.0
80.0
65.3
60.3
75.0
60.0
75.0
75.0
60.0
75.0
60.0
40.0
49.5
+/+
+/+
-/-
65.0
78.8
+/+
+/+
+/+
+/+
-/+
108.0
108.0
135.0
146.3
Physical Characteristics
The following table lists the monitor's physical characteristics:
Model Number
Dell E1913S monitor
Dell E1913 monitor
Dell E2213 monitor
D-subminiature, blue connector
DVI-D: White connector
D-subminiature, blue connector;
Connector type
D-subminiature, blue connector
DVI-D: White connector
Analog: Detachable, D-Sub, 15 pins, shipped
attached to the monitor
D-sub: Detachable, Analog, 15 pin, shipped
attached to the monitor
Analog: Detachable, D-Sub, 15 pins, shipped
attached to the monitor
Signal cable type
DVI-D: Detachable, DVI-D, Solid pins (optional)
DVI-D: Detachable, DVI-D, Solid pins (optional)
Dimensions: (with stand)
Height
Width
Depth
408.6 mm (16.09 inches)
411.9 mm (16.22 inches)
163.5 mm (6.44 inches)
372.8 mm (14.68 inches)
443.8 mm (17.47 inches)
163.5 mm (6.44 inches)
414.2 mm (16.31 inches)
510.4 mm (20.09 inches)
180.1 mm (7.09 inches)
Dimensions: (without stand)
Height
Width
Depth
336.7 mm (13.26 inches)
411.9 mm (16.22 inches)
52.0 mm (2.05 inches)
290.8 mm (11.45 inches)
443.8 mm (17.47 inches)
52.0 mm (2.05 inches)
332.7 mm (13.10 inches)
510.4 mm (20.09 inches)
52.0 mm (2.05 inches)
Stand dimensions:
Height
141.4 mm (5.57 inches)
236.0 mm (9.29 inches)
163.5 mm (6.44 inches)
141.4 mm (5.57 inches)
236.0 mm (9.29 inches)
163.5 mm (6.44 inches)
169.6mm (6.68 inches)
255.0 mm (10.04 inches)
180.1 mm (7.09 inches)
Width
Depth
Weight:
Weight with packaging
4.08 kg (8.98 lbs)
3.43 kg (7.55 lbs)
3.90 kg (8.58 lbs)
3.28 kg (7.22 lbs)
5.13 kg (11.29 lbs)
4.37 kg (9.61 lbs)
Weight with stand assembly and cables
Weight without stand assembly
(For wall mount or VESA mount
considerations - no cables)
2.79 kg (6.14 lbs)
0.33 kg (0.73 lbs)
2.54 kg (5.59 lbs)
0.33 kg (0.73 lbs)
3.17 kg (6.97 lbs)
0.79 kg (1.74 lbs)
Weight of stand assembly
Environmental Characteristics
The following table lists the environmental conditions for your monitor:
Model Number
Dell E1913S monitor
Dell E1913 monitor
Dell E2213 monitor
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/about.htm[2012-3-19 16:21:58]
About Your Monitor: Dell E1913S/E1913/E2213 Monitor User's Guide
Temperature
Operating
0 ° C to 40 ° C (32 ° F to 104 ° F)
0 ° C to 40 ° C (32 ° F to 104 ° F)
0 ° C to 40 ° C (32 ° F to 104 ° F)
Non-operating
Storage: -20 ° C to 60 ° C (-4 ° F to 140 ° F)
Shipping: -20 ° C to 60 ° C (-4 ° F to 140 ° F) Shipping: -20 ° C to 60 ° C (-4 ° F to 140 ° F) Shipping: -20 ° C to 60 ° C (-4 ° F to 140 °
F)
Storage: -20 ° C to 60 ° C (-4 ° F to 140 ° F) Storage: -20 ° C to 60 ° C (-4 ° F to 140 ° F)
Humidity
10 % to 80 % (non-condensing)
10 % to 80 % (non-condensing)
10 % to 80 % (non-condensing)
Operating
Storage: 5 % to 90 % (non-condensing)
Shipping: 5 % to 90 % (non-condensing)
Storage: 5 % to 90 % (non-condensing)
Shipping: 5 % to 90 % (non-condensing)
Storage: 5 % to 90 % (non-condensing)
Shipping: 5 % to 90 % (non-condensing)
Non-operating
Altitude
Operating
Non-operating
3,048 m (10,000 ft) max
10,668 m (35,000 ft) max
3,048 m (10,000 ft) max
10,668 m (35,000 ft) max
3,048 m (10,000 ft) max
10,668 m (35,000 ft) max
78.48 BTU/hour (maximum)
61.42 BTU/hour (typical)
78.48 BTU/hour (maximum)
61.42 BTU/hour (typical)
81.89 BTU/hour (maximum)
64.83 BTU/hour (typical)
Thermal dissipation
LCD Monitor Quality & Pixel Policy
During the LCD Monitor manufacturing process, it is not uncommon for one or more pixels to become fixed in an unchanging state. The visible result is a fixed pixel that appears as an extremely tiny dark or bright
discolored spot. When the pixel remains permanently lit, it is known as a "bright dot". Wh en the pixel remains black, it is known as a "dark dot".
In almost every case, these fixed pixels are hard to see and do not detract from display quality or usability. A display with 1 to 5 fixed pixels is considered normal and within competitive standards. For more information,
Maintenance Guidelines
Caring for Your Monitor
CAUTION: Before cleaning the monitor, unplug the monitor power cable from the electrical outlet.
For best practices, follow the instructions in the list below while unpacking, cleaning, or handling your monitor:
To clean your antistatic screen, slightly dampen a soft, clean cloth with water. If possible, use a special screen-cleaning tissue or solution suitable for the antistatic coating. Do not use benzene, thinner, ammonia,
abrasive cleaners, or compressed air.
Use a slightly dampened, warm cloth to clean the plastics. Avoid using detergent of any kind as some detergents leave a milky film on the plastics.
If you notice a white powder when you unpack your monitor, wipe it off with a cloth. This white powder occurs during the shipping of the monitor.
Handle your monitor with care as a darker-colored monitor may scratch and show white scuff marks more than a lighter-colored monitor.
To help maintain the best image quality on your monitor, use a dynamically changing screen saver and power off your monitor when not in use.
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/about.htm[2012-3-19 16:21:58]
Dell E1913S/E1913/E2213 Monitor User's Guide
Setting Up the Monitor
Dell™ E1913S/E1913/E2213 Monitor User's Guide
Attaching the Stand
NOTE: The stand base is detached when the monitor is shipped from the factory.
1. Assemble the stand riser to stand base.
a. Place the monitor stand base on a stable table top.
b. Slide the monitor stand body in the correct direction down onto the stand base until it clicks into place.
2. Attach the stand assembly to the monitor:
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/setup.htm[2012-3-19 16:22:02]
Dell E1913S/E1913/E2213 Monitor User's Guide
a. Place the monitor on a soft cloth or cushion near the edge of desk.
b. Align the stand assembly bracket to the monitor groove.
c. Insert the bracket towards monitor until it locks in place.
Removing the Monitor Stand for VESA Wall Mount
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/setup.htm[2012-3-19 16:22:02]
Dell E1913S/E1913/E2213 Monitor User's Guide
After placing the monitor panel on a soft cloth or cushion, complete the following steps to remove the monitor stand:
1. Use a long screwdriver to push the release latch located in a hole just above the monitor stand.
2. Once the latch is released, remove the monitor stand away from the monitor.
Connecting Your Monitor
To connect your monitor to the computer:
1. Turn off your computer and disconnect the power cable.
2. Connect either the white (digital DVI-D) or the blue (analog VGA) display connector cable to the corresponding video port on the back of your computer. Do not use
both cables on the same computer. Use both the cables only when they are connected to two different computers with appropriate video systems.
Connecting the Blue VGA Cable
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/setup.htm[2012-3-19 16:22:02]
Dell E1913S/E1913/E2213 Monitor User's Guide
Connecting the white DVI cable (for E1913/E2213 only)
CAUTION: The graphics are used for the purpose of illustration only. Appearance on the computer may vary.
Attaching Dell Soundbar AX510PA (optional)
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/setup.htm[2012-3-19 16:22:02]
Dell E1913S/E1913/E2213 Monitor User's Guide
CAUTION: Do not use with any device other than the Dell Soundbar.
To attach the soundbar:
1.
2.
3.
4.
Working from the back of the monitor, attach Soundbar by aligning the two slots with the two tabs along the bottom of the monitor.
Slide the Soundbar to the left until it snaps into place.
Connect the Soundbar with the DC power connector from the Soundbar Power Adapter.
Insert the mini stereo plug from the back of the Soundbar into the computer's audio output jack.
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/setup.htm[2012-3-19 16:22:02]
Dell E1913S/E1913/E2213 Monitor User's Guide
Operating the Monitor
Dell™ E1913S/E1913/E2213 Monitor User's Guide
Power On the Monitor
Press the
button to turn on the monitor.
Using the Front Panel Controls
Use the buttons on the front of the monitor to adjust the image settings.
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
Front panel button
A
Description
Preset modes
B
Use the Brightness / Contrast button to direct access to the "Brightness" and "Contrast" control menu.
Brightness / Contrast
C
Use Menu button to open the on-screen display (OSD).
Menu
D
Use the Exit button to exit on-screen display (OSD) from menu and sub-menus.
Exit
Front panel button
Use the button on the front of the monitor to adjust the image settings.
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
Front panel button
A
Description
Use the Up button to adjust (increase ranges) items in the OSD menu.
Up
B
Use the Down button to adjust (decrease ranges) items in the OSD menu.
Down
C
Use the OK button to confirm your selection.
OK
D
Use the Back button to go back to the previous menu.
Back
Using the On-Screen Display (OSD) Menu
Accessing the Menu System
NOTE: If you change the settings and then either proceed to another menu or exit the OSD menu, the monitor automatically saves those changes. The changes are also
saved if you change the settings and then wait for the OSD menu to disappear.
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
1. Press the
button to open the OSD menu and display the main menu.
Main Menu
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
2. Press the and buttons to toggle between options in the Menu. As you move from one icon to another, the option name is highlighted.
3. To select the highlighted item on the menu press the button again.
buttons to select the desired parameter.
4. Press the
5. Press the
6. Select the
and
button to enter the slide bar and then use the
or
buttons, according to the indicators on the menu, to make your changes.
to accept and return to previous menu.
to return to previous menu without accepting current settings or
The table below provides a list of all the OSD menu options and their functions.
Icon
Menu and
Submenus
Description
This meter shows the energy level being consumed by the monitor in real time.
Energy Use
Brightness/Contrast Use the Brightness and Contrast menu to adjust the Brightness/Contrast.
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
Brightness
Allows you to adjust the brightness or luminance of the backlight.
Press the button to increase brightness and press the button to decrease brightness (min 0 ~ max 100).
Contrast
Allows you to adjust the contrast or the degree of difference between darkness and lightness on the monitor screen. Adjust brightness first,
and adjust contrast only if you need further adjustment.
Press the
button to increase contrast and press the
button to decrease contrast (min 0 ~ max 100).
Auto Adjust
Use this button to activate automatic setup and adjust menu. The following dialog appears on a black screen as the monitor self-adjusts to
the current input:
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
Auto Adjustment allows the monitor to self-adjust to the incoming video signal. After using Auto Adjustment, you can further tune your
monitor by using the Pixel Clock (Coarse) and Phase (Fine) controls under Display Settings.
NOTE: Auto Adjust option is only available when you are using an analog (VGA) connector.
Input Source (for
E1913 and E2213
only)
Use the Input Source menu to select between different video signals that may be connected to your monitor.
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
Auto Select
VGA
Select Auto Select to scan for available input signals.
Select VGA input when you are using the analog (VGA) connector. Push
to select the VGA input source.
to select the DVI input source.
DVI-D
Select DVI-D input when you are using the Digital (DVI) connector. Push
Color Settings
Use the Color Settings menu adjust the monitor's color settings.
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
Input Color Format
Allows you to set the video input mode to:
RGB: Select this option if your monitor is connected to a computer or DVD player using the HDMI to DVI adapter.
YPbPr: Select this option if your DVD player supports only YPbPr output.
Preset Modes
Allows you to choose from a list of preset color modes.
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
Standard: Loads the monitor's default color settings. This is the default preset mode.
Multimedia: Loads color settings ideal for multimedia applications.
Text: Loads color settings ideal for office environment.
Warm: Decreases the color temperature. The screen appears warmer with a red/yellow tint.
Cool: Increases the color temperature. The screen appears cooler with a blue tint.
Custom Color: Allows you to manually adjust the color settings. Press the
and
button to adjust the Red, Green, and Blue
values and create your own preset color mode.
Use the Displays Settings menu to adjust the monitor's display settings.
Display Settings
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
Adjusts the image ratio as Wide 16:10, 4:3, or 5:4.
Aspect Ratio
(for E1913 and E2213
NOTE: Wide 16:10 adjustment is not required at maximum preset resolution 1440 x 900 (for E1913) or 1680 x 1050 (for E2213) .
only)
Horizontal Position
Use the
Use the
or
or
buttons to adjust image left and right. Minimum is '0' (-). Maximum is '100' (+).
buttons to adjust image up and down. Minimum is '0' (-). Maximum is '100' (+).
Vertical Position
Sharpness
Pixel Clock
Phase
This feature can make the image look sharper or softer. Use
or
to adjust the sharpness from '0' to '100'.
The Phase and Pixel Clock adjustments allow you to adjust your monitor to your preference. Use
quality.
or
buttons to adjust for best image
If satisfactory results are not obtained using the Phase adjustment, use the Pixel Clock (coarse) adjustment and then use Phase (fine),
again.
NOTE: Horizontal Position, Vertical Position, Pixel Clock and Phase adjustment are only available for VGA input.
Reset Display
Settings
Select this option to restore default display settings.
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
Select this option to adjust the settings of the OSD, such as, the languages of the OSD, the amount of time the menu remains on screen,
and so on.
Other Settings
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
Language
Allows you to set the OSD display to one of eight languages: English, Spanish, French, German, Brazilian Portuguese, Russian, Simply
Chinese, Japanese.
Menu Transparency Allows you to adjust the OSD background from opaque to transparent.
Menu Timer
Menu Lock
Allows you to set the time for which the OSD remains active after you press a button on the monitor.
Use the
and
button to adjust the slider in 1 second increments, from 5 to 60 seconds.
Controls user access to adjustments. When Lock is selected, no user adjustments are allowed. All button are locked except
button.
NOTE: When the OSD is locked, pressing the menu button takes you directly to the OSD settings menu, with 'OSD Lock' pre-selected
on entry. press and hold
button for 10 seconds to unlock and allow user access to all applicable settings.
DDC/CI
DDC/CI (Display Data Channel/Command Interface) allows a software on your computer to adjust the monitor display settings like the
brightness, color balance etc.
Enable (Default): Optimizes the performance of your monitor and provides a better customer experience.
Disable: Disables the DDC/CI option and the following message appears on the screen.
This feature helps reduce minor cases of image retention.
LCD Conditioning
If an image appears to be stuck on the monitor, select LCD Conditioning to help eliminate any image retention. Using the LCD Conditioning
feature may take some time. LCD Conditioning feature cannot remove severe cases of image retention or burn-in.
NOTE: Use LCD Conditioning only when you experience a problem with image retention.
The below warning message appears once user selects " Enable" LCD Conditioning.
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
Factory Reset
Personalize
Resets all OSD settings to the factory preset values.
Select this option allows you to set two shortcut button.
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
Shortcut Key 1
User can select from "Preset Modes", "Brightness/Contrast", "Auto Adjust", "Input Source" (for E1913 and E2213 only), "Aspect Ratio" (for
E1913 and E2213 only) and set as shortcut Key.
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
Shortcut Key 2
User can select from "Preset Modes", "Brightness/Contrast", "Auto Adjust", "Input Source"(for E1913 and E2213 only), "Aspect Ratio" (for
E1913 and E2213 only) and set as shortcut key.
Reset Personalize
Allows you to restore shortcut key to the default setting.
OSD Messages
When the monitor does not support a particular resolution mode you will see the following message:
E1913S:
E1913:
E2213:
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
This means that the monitor cannot synchronize with the signal that it is receiving from the computer. See Monitor Specifications for the horizontal and
vertical frequency ranges addressable by this monitor. Recommended mode is 1280 x 1024 (for E1913S) or 1440 x 900 (for E1913) or 1680 x 1050 (for
E2213).
You will see the following message before the DDC/CI function is disabled.
When the monitor enters the Power Save mode, the following message appears:
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
If you press any button other than the power button the following messages will appear depending on the selected input:
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
If VGA or DVI cable is not connected, a floating dialog box as shown below appears. The monitor will enter Power Save Mode after 5 minutes if left at this state.
Setting the Maximum Resolution
To set the Maximum resolution for the monitor:
Windows Vista® , Windows® 7:
1. Right-click on the desktop and select Personalization.
2. Click Change Display Settings.
3. Move the slider-bar to the right by pressing and holding left-mouse button and adjust the screen resolution to 1280 x 1024 (for E1913S) or 1440 x 900 (for E1913) or
1680 x 1050 (for E2213).
4. Click OK.
If you do not see 1280 x 1024 (for E1913S) or 1440 x 900 (for E1913) or 1680 x 1050 (for E2213) as an option, you may need to update your graphics driver. Depending on
your computer, complete one of the following procedures.
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
If you have a Dell desktop or portable computer:
Go to support.dell.com, enter your service tag, and download the latest driver for your graphics card.
If you are using a non-Dell computer (portable or desktop):
Go to the support site for your computer and download the latest graphic drivers.
Go to your graphics card website and download the latest graphic drivers.
Using the Dell Soundbar
The Dell Soundbar is a stereo two channel system, mountable on Dell Flat Panel Displays. The soundbar has an on/off power and rotary volume control to adjust the overall sound
system, an LED for power indication and two audio headset jacks
1.
2
Attach mechanism
Power control/ indicator
Volume control
3.
4.
5.
Audio-in jack
Headphone jack
Using the Tilt
Tilt
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
With the stand assembly, you can tilt the monitor for the most comfortable viewing angle.
NOTE: The stand base is detached when the monitor is shipped from the factory.
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/operate.htm[2012-3-19 16:22:04]
Dell E1913S/E1913/E2213 Monitor User's Guide
Troubleshooting
Dell™ E1913S/E1913/E2213 monitor
Self-Test
Your monitor provides a self-test feature that allows you to check whether your monitor is functioning properly. If your monitor and computer are properly
connected but the monitor screen remains dark, run the monitor self-test by performing the following steps:
1. Turn off both your computer and the monitor.
2. Unplug the video cable from the back of the computer. To ensure a successful Self-Test operation, remove the Analog connector for E1913S. For E1913
and E2213, remove both the Digital (white connector) and the Analog (blue connector) connectors from the back of the computer.
3. Turn on the monitor.
The floating dialog box should appear on-screen (against a black background) if the monitor cannot sense a video signal and is working correctly.
While in self-test mode, the power LED remains blue. Also, depending upon the selected input, one of the dialogs shown below will continuously scroll
through the screen.
or
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/solve.htm[2012-3-19 16:22:08]
Dell E1913S/E1913/E2213 Monitor User's Guide
4. This box also appears during normal system operation, if the video cable becomes disconnected or damaged. The monitor will enter Power Save Mode
after 5 minutes if left at this state.
5. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor.
If your monitor screen remains blank after you use the previous procedure, check your video controller and computer, because your monitor is functioning
properly.
NOTE: Self-test feature check is not available for S-Video, Composite, and Component video modes.
Built-in Diagnostics
Your monitor has a built-in diagnostic tool that helps you determine if the screen abnormality you are experiencing is an inherent problem with your monitor, or
with your computer and video card.
NOTE: You can run the built-in diagnostics only when the video cable is unplugged and the monitor is in self-test mode.
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/solve.htm[2012-3-19 16:22:08]
Dell E1913S/E1913/E2213 Monitor User's Guide
To run the built-in diagnostics:
1. Ensure that the screen is clean (no dust particles on the surface of the screen).
2. Unplug the video cable(s) from the back of the computer or monitor. The monitor then goes into the self-test mode.
3. Press and hold the Button 1 and Button 4 on the front panel simultaneously for 2 seconds. A gray screen appears.
4. Carefully inspect the screen for abnormalities.
5. Press the Button 4 on the front panel again. The color of the screen changes to red.
6. Inspect the display for any abnormalities.
7. Repeat steps 5 and 6 to inspect the display in green, blue, black, white and text screens.
The test is complete when the white screen appears. To exit, press the Button 4 again.
If you do not detect any screen abnormalities upon using the built-in diagnostic tool, the monitor is functioning properly. Check the video card and computer.
Common Problems
The following table contains general information about common monitor problems you might encounter and the possible solutions.
Common Symptoms
No Video/Power LED off
What You Experience
No picture
Possible Solutions
Ensure that the video cable connecting the monitor and the computer is properly connected
and secure.
Verify that the power outlet is functioning properly using any other electrical equipment.
Ensure that the power button is depressed fully.
No Video/Power LED on
No picture or no brightness
Increase brightness & contrast controls via OSD.
Perform monitor self-test feature check.
Check for bent or broken pins in the video cable connector.
Run the built-in diagnostics.
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/solve.htm[2012-3-19 16:22:08]
Dell E1913S/E1913/E2213 Monitor User's Guide
Poor Focus
Picture is fuzzy, blurry, or
ghosting
Perform Auto Adjust via OSD.
Adjust the Phase and Pixel Clock controls via OSD.
Eliminate video extension cables.
Reset the monitor to Factory Settings.
Change the video resolution to the correct aspect ratio (16:10).
Shaky/Jittery Video
Wavy picture or fine
movement
Perform Auto Adjust via OSD.
Adjust the Phase and Pixel Clock controls via OSD.
Reset the monitor to Factory Settings.
Check environmental factors.
Relocate the monitor and test in another room.
Missing Pixels
LCD screen has spots
Cycle power on-off.
Pixel that is permanently off is a natural defect that can occur in LCD technology.
For more information on Dell Monitor Quality and Pixel Policy, see Dell Support site at:
Stuck-on Pixels
LCD screen has bright spots
Cycle power on-off.
Pixel that is permanently off is a natural defect that can occur in LCD technology.
For more information on Dell Monitor Quality and Pixel Policy, see Dell Support site at:
Brightness Problems
Geometric Distortion
Picture too dim or too bright
Screen not centered correctly
Reset the monitor to Factory Settings.>
Auto Adjust via OSD.
Adjust brightness & contrast controls via OSD.
Reset the monitor to Factory Settings.
Auto Adjust via OSD.
Adjust brightness & contrast controls via OSD.
NOTE: When using 'DVI-D', the positioning adjustments are not available.
Horizontal/Vertical Lines
Synchronization Problems
Screen has one or more lines
Reset the monitor to Factory Settings.
Perform Auto Adjust via OSD.
Adjust Phase and Pixel Clock controls via OSD.
Perform monitor self-test feature check and determine if these lines are also in self-test
mode.
Check for bent or broken pins in the video cable connector.
NOTE: When using 'DVI-D', the Pixel Clock and Phase adjustments are not available.
Screen is scrambled or
appears torn
Reset the monitor to Factory Settings.
Perform Auto Adjust via OSD.
Adjust Phase and Pixel Clock controls via OSD.
Perform monitor self-test feature check to determine if the scrambled screen appears in
self-test mode.
Check for bent or broken pins in the video cable connector.
Restart the computer in the safe mode.
Safety-Related Issues
Intermittent Problems
Visible signs of smoke or
sparks
Do not perform any troubleshooting steps.
Contact Dell immediately.
Monitor malfunctions on & off
Ensure that the video cable connecting the monitor to the computer is connected properly
and is secure.
Reset the monitor to Factory Settings.
Perform monitor self-test feature check to determine if the intermittent problem occurs in
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/solve.htm[2012-3-19 16:22:08]
Dell E1913S/E1913/E2213 Monitor User's Guide
self-test mode.
Missing Color
Picture missing color
Picture color not good
Perform monitor self-test feature check.
Ensure that the video cable connecting the monitor to the computer is connected properly
and is secure.
Check for bent or broken pins in the video cable connector.
Wrong Color
Change the Color Setting Mode in the Color Settings OSD to Graphics or Video depending
on the application.
Try different Color Preset Settings in Color Settings OSD. Adjust R/G/B value in Color
Settings OSD if the Color Management is turned off.
Change the Input Color Format to PC RGB or YPbPr in the Advance Setting OSD.
Image retention from a static Faint shadow from the static
image left on the monitor for image displayed appears on
Use the Power Management feature to turn off the monitor at all times when not in use(for
Alternatively, use a dynamically changing screensaver.
a long period of time
the screen
Product Specific Problems
Specific Symptoms
What You Experience
Possible Solutions
Screen image is too small
Image is centered on screen,
but does not fill entire viewing
area
Reset the monitor to Factory Settings.
Cannot adjust the monitor with OSD does not appear on the
the buttons on the front panel screen
Turn off the monitor, unplug the power cord, plug back, and then turn on the monitor.
No Input Signal when user
controls are pressed
No picture, the LED light is
blue. When you press "up",
"down" or "Menu" key, the
message " No input signal" will
appear.
Check the signal source. Ensure the computer is not in the power saving mode by
moving the mouse or pressing any key on the keyboard.
Check whether the signal cable is plugged in properly. Re-plug the signal cable if
necessary.
Reset the computer or video player.
The picture does not fill the
entire screen
The picture cannot fill the
height or width of the screen
Due to different video formats (aspect ratio) of DVDs, the monitor may display in full
screen.
Run the built-in diagnostics.
NOTE: When choosing DVI-D mode, the Auto Adjust function is not available.
Dell™ Soundbar Problems
Common Symptoms
What You Experience
Possible Solutions
No sound for system where the No power to Soundbar - the
Soundbar draws power from an power indicator is off
AC adapter
Turn the Power/Volume knob on the Soundbar clockwise to the middle position; check if
the power indicator (blue LED) on the front of the Soundbar is illuminated.
Confirm that the power cable from the Soundbar is plugged into the adapter.
No Sound
Soundbar has power - power
indicator is on
Plug the audio line-in cable into the computer's audio out jack.
Set all volume controls to their maximum and ensure that the mute option is not
enabled.
Play some audio content on the computer (example, audio CD, or MP3).
Turn the Power/Volume knob on the Soundbar clockwise to a higher volume setting.
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/solve.htm[2012-3-19 16:22:08]
Dell E1913S/E1913/E2213 Monitor User's Guide
Clean and reseat the audio line-in plug.
Test the Soundbar using another audio source (For example: portable CD player, MP3
player).
Distorted Sound
Computer's sound card is used
as the audio source
Clear any obstructions between the Soundbar and the user.
Confirm that the audio line-in plug is completely inserted into the jack of the sound
card.
Set all Windows volume controls to their midpoints.
Decrease the volume of the audio application.
Turn the Power/Volume knob on the Soundbar counter-clockwise to a lower volume
setting.
Clean and reseat the audio line-in plug.
Troubleshoot the computer's sound card.
Test the Soundbar using another audio source (For example: portable CD player, MP3
player).
Avoid using an audio cable extension or audio jack converter.
Distorted Sound
Other audio source is used
Clear any obstructions between the Soundbar and the user.
Confirm that the audio line-in plug is completely inserted into the jack of the audio
source.
Decrease the volume of the audio source.
Turn the Power/Volume knob on the Soundbar counter-clockwise to a lower volume
setting.
Clean and reseat the audio line-in plug.
Unbalanced Sound Output
Sound from only one side of
Soundbar
Clear any obstructions between the Soundbar and the user.
Confirm that the audio line-in plug is completely inserted into the jack of the sound card
or audio source.
Set all Windows audio balance controls (L-R) to their midpoints.
Clean and reseat the audio line-in plug.
Troubleshoot the computer's sound card.
Test the Soundbar using another audio source (For example: portable CD player, MP3
player).
Low Volume
Volume is too low
Clear any obstructions between the Soundbar and the user.
Turn the Power/Volume knob on the Soundbar clockwise to the maximum volume
setting.
Set all Windows volume controls to their maximum.
Increase the volume of the audio application.
Test the Soundbar using another audio source (For example: portable CD player, MP3
player)
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/solve.htm[2012-3-19 16:22:08]
Dell E1913S/E1913/E2213 Monitor User's Guide
Appendix
Dell™ E1913S/E1913/E2213 Monitor User's Guide
WARNING: Safety Instructions
WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to
shock, electrical hazards, and/or mechanical hazards.
For information on safety instructions, see the Product Information Guide.
FCC Notices (U.S. Only) and Other Regulatory Information
For FCC notices and other regulatory information, see the regulatory compliance website located at www.dell.com\regulatory_compliance.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference
(2) this device must accept any interference received including interference that may cause undesired operation
Contacting Dell
For customers in the United States, call 800-WWW-DELL (800-999-3355).
NOTE:If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or
Dell product catalog.
Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services
may not be available in your area. To contact Dell for sales, technical support, or customer service issues:
2. Verify your country or region in the Choose A Country/Region drop-down menu at the bottom of the page.
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/appendx.htm[2012-3-19 16:22:09]
Dell E1913S/E1913/E2213 Monitor User's Guide
3. Click Contact Us on the left side of the page.
4. Select the appropriate service or support link based on your need.
5. Choose the method of contacting Dell that is convenient for you.
file:///K|/Dell/E1913/Dell%20E1913(S)%20E2213%20E-DOC%20Source/en/ug/appendx.htm[2012-3-19 16:22:09]
|