DVD Recorder + VCR
DVD Recorder + VCR
DF-4501P
User Manual
Im p o rta n t Sa fe g u a rd s
Im p o r ta n t Sa fe g u a rd s
Im p o r ta n t Sa fe g u a rd s
This set has been designed and manufactured to
assure personal safety. Improper use can result in
electric shock or fire hazard. The safeguards
incorporated in this unit will protect you if you
observe the following procedures for installation, use
and servicing. This unit is fully transistorized and does
not contain any parts that can be repaired by the user.
ventilation to ensure reliable operation of the unit
and to protect it from overheating. These
openings must not be blocked or covered. These
openings must not be blocked by placing the unit
on a bed, sofa, rug, or other similar surface. This
unit should never be placed near or over a
radiator or heat radiator. This unit should not be
placed in a built-in installation such as a
bookcase or rack unless proper ventilation is
provided or the manufacturer’s instructions have
been adhered to.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
‘dangerous voltage‘ within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and servicing instructions in
the literature accompanying the appliance.
1
2
3
4
5
READ INSTRUCTIONS
All the safety and operating instructions should
be read before the unit is operated.
QUALIFIED SERVICE PERSONNEL.
RETAIN INSTRUCTIONS
The safety and operating instructions should be
retained for future reference.
1 0 POWER SOURCES
This unit should be operated only from the type of
power source indicated on the marking label. If
you are not sure of the type of power supply to
your home, consult your dealer or local power
company. For units intended to operate from
battery power, or other sources, refer to the
operating instructions.
WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE.
HEED WARNINGS
All warnings on the unit and in the operating
instructions should be adhered to.
CAUTION
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
FOLLOW INSTRUCTIONS
All operating and use instructions should be
followed.
IMPORTANT FOR LASER PRODUCTS
LASER
1 1 POWER-CORD PROTECTION
This Digital Video Disc Player employs a Laser System. To ensure proper use of this product please
read this owner’s manual carefully and retain for future reference. Should the unit require
maintenance, contact an authorized service location - see service procedure.
Use of control adjustments or the performance of procedures other than those specified may result
in hazardous radiation exposure.
To prevent direct exposure to the laser beam, do not try to open the enclosure. Visible laser
radiation when open and interlocks defeated.
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them, paying particular
attention to cords at plugs, convenience
receptacles, and the point where they exit from
the unit.
CLEANING
Unplug this unit from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
6
7
8
ATTACHMENTS
1 2 LIGHTNING
Do not use attachments unless recommended by
the unit’s manufacturer as they may cause
hazards.
DO NOT STARE INTO THE BEAM.
For added protection for this unit during a
lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from
the wall outlet and disconnect the antenna or
cable system. This will prevent damage to the
unit due to lightning and power line surges.
DANGER Visible laser radiation when open and interlock failed or defeated.
Avoid direct exposure to beam.
CLASS 1
WATER AND MOISTURE
CAUTION Do not open the top cover. There are no user serviceable parts inside the
LASER PRODUCT
Do not use this unit near water- for example, near
a bath tub, wash bowl, kitchen sink or laundry
tub, in a wet basement, or near a swimming pool.
Unit; leave all servicing to qualified service personnel.
1 3 DISC TRAY
ACCESSORIES
Keep your fingers well clear of the disc as it is
closing. It may cause serious personal injury.
Do not place this unit on an unstable cart, stand,
tripod, bracket, or table. The unit may fall,
causing serious injury to a child or adult as well
as serious damage to the unit. Use this unit only
with a cart, stand , tripod, bracket, or table
recommended by the manufacturer.
CAUTION
Any changes or modification in construction of this device which are not expressly approved by
the party responsible for compliance could void the user’s authority to operate the equipment.
1 4 OVERLOADING
Do not overload wall outlets of extension cords
as this can result in a risk of fire or electric shock.
1 5 OBJECT AND LIQUID ENTRY
PORTABLE CART WARNING
(symbol provided by RETAC)
8 A A unit and cart combination
should be moved with care.
Quick stops, excessive force,
and uneven surfaces may
cause the product and cart
combination to overturn.
Never push objects of any kind into this unit
through openings as they may touch dangerous
voltage points or ‘short-out’ parts that could
result in a fire or electric shock. Never spill liquid
of any kind on the unit.
1 6 BURDEN
9
VENTILATION
Do not place a heavy object on or step on the
product. The object may fall, causing serious
Slots and openings in the case are provided for
ii
iii
Im p o rta n t Sa fe g u a rd s
Ta b le o f Co n te n ts
Ta b le o f Co n te n ts
personal injury and serious damage to the
product.
2 3 HEAT
IN TRO DUCTIO N
RECO RDIN G
The product should be situated away from heat
sources such as radiators, heat registers, stoves,
or other products (including amplifiers) that
produce heat.
1 7 DISC
Im p o rta n t Sa fe g u a rd s _________________________i
Ta b le o f Co n te n ts ______________________________1
O ve rvie w ______________________________________2
Id e n tifica tio n o f Co n tro ls_______________________6
Ba sic Re co rd in g ________________________________3 9
Do not use a cracked, deformed or repaired disc.
These discs are easily broken and may cause
serious personal injury and product malfunction.
Recording from TV
39
39
40
40
40
41
41
41
One Touch Record (OTR)
Checking the Recording Time
To Pause the Recording
One Touch Copy - DVD to VHS
Copy Edit (DVD ➝➝VCR)
One Touch Copy - VHS to DVD
Copy Edit (VCR ➝➝DVD)
2 4 To prevent battery electrolyte leakage, which may
result in injury and damage to the unit or other
objects, observe the following precautions;
1 8 SERVICING
Do not attempt to service this unit yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
A. All batteries must be installed with the proper
polarity.
CO N N ECTIO N S
B. Do not mix new with old or used batteries.
C. Only use batteries of the same type and brand.
Co n n e ctin g An te n n a / Ca b le ____________________1 2
Co n n e ctin g a TV _______________________________1 3
Co n n e ctin g a n Am p lifie r/ Re ce ive r _____________1 4
Co n n e ctin g O p tio n a l Eq u ip m e n t ______________1 5
Co n n e ctin g a Dig ita l Ca m co rd e r ______________1 5
1 9 DAMAGE REQUIRING SERVICE
Tim e r Re co rd in g _______________________________4 2
Re co rd in g fro m a n Ex te rn a l In p u t _____________4 5
Unplug this unit from the wall outlet and refer
servicing to qualified service personnel under the
following conditions.
D. Remove the batteries when they are not to be
used for a long period time.
A. When the power-supply cord or plug is damaged.
B. If liquid has been spilled, or objects have fallen
into the unit.
E. When the batteries have become discharged,
they must be disposed of in a safe manner
which complies with all applicable laws.
DISC O PERATIO N
C. If the unit has been exposed to rain or water.
2 5 WEEE (Wa ste Electrica l a nd Electronic Equipm ent)
The meaning of the symbol on the
Disc In itia lize __________________________________4 7
Disc O p e ra tio n in DVD±RW d isc _______________4 7
Disc O p e ra tio n in DVD±R, DVD-RW d isc _______4 9
D. If the unit does not operate normally by following
the operating instructions. Adjust only those
controls that are covered by the operating
instructions. Improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the unit to its normal operation.
E. If the unit has been dropped or the cabinet has
been damaged.
F. When the unit exhibits a distinct change in
performance-this indicates a need for service.
SETUP
product, its accessory or packaging
indicates that this product shall not
be treated as household waste.
Please, dispose of this equipment at
your applicable collection point for
the recycling of electrical &
In itia l In sta lla tio n ______________________________1 6
In itia l Se tu p ____________________________________1 7
Setup Menu Overview
17
17
21
22
23
24
25
26
27
27
28
28
INSTALLATION Settings
RECORDING OPTIONS Settings
LANGUAGE Settings
PREFERENCE / Video Settings
PREFERENCE / Audio Settings
PREFERENCE / Parental Controls
Various PREFERENCE Settings
Preferences / VCR
electronic equipments waste. In the European
Union and Other European countries which there
are separate collection systems for used
electrical and electronic product. By ensuring the
correct disposal of this product, you will help
prevent potentially hazardous to the environment
and to human health, which could otherwise be
caused by unsuitable waste handling of this
product. The recycling of materials will help
conserve natural resources. Please do not
therefore dispose of your old electrical and
electronic equipment with your household waste.
For more detailed information about recycling of
this product, please contact your local city office,
your household waste disposal service or the
shop where you purchased the product.
DISC EDIT
Title Me n u _____________________________________5 0
2 0 REPLACEMENT PARTS
When replacement parts are required, have the
service technician verify that the replacements he
uses have the same safety characteristics as the
original parts. Use of replacements specified by
the unit manufacturer can prevent fire, electric
shock, or other hazards.
REFEREN CE
Preferences / Modulator Out
System Information
Restore Defaults
Tro u b le sh o o tin g _______________________________5 3
Te ch n ica l Sp e cifica tio n s ________________________5 6
2 1 SAFETY CHECK
O n -Scre e n Disp la y O ve rvie w __________________2 9
Upon completion of any service or repairs to this
unit, ask the service technician to perform safety
checks recommended by the manufacturer to
determine that the unit is in safe operating
condition.
PLAYBACK
DVD Pla y b a ck _________________________________3 1
VCR Pla y b a ck _________________________________3 4
O th e r Disc Pla y b a ck __________________________3 6
2 2 WALL OR CEILING MOUNTING
The product should be mounted to a wall or
ceiling only as recommended by the
manufacturer.
iv
1
O ve rvie w
O ve r vie w
O ve r vie w
DVD, DVD+R, DVD+RW ?
Re g io n a l co d e
If the region number on your DVD disc does not correspond to the region
number of this player, the disc cannot be played.
Wha t is a DVD?
DVD (Digital Versatile Disc) is a storage medium that combines the convenience of the compact disc with the
latest digital video technology. DVD video uses modern MPEG2 data compression technology that enables an
entire feature film to be stored on a single five inch disc.
ALL
2
How good is the resolution of DVD com pa red w ith VHS?
The razor-sharp digital images have more than 500 lines of resolution at 720 pixels per line. This is more than
twice as high as VHS and even better than laser disc quality. DVD picture quality is easily comparable to the
digital masters produced in recording studios.
W h ich d iscs y o u ca n u se
Wha t is a DVD+RW?
The following discs can be used in your DVD Recorder+VCR:
DVD+ReWritable uses ‘phase change‘ media, the same technology on which rewritable CDs are based. A high-
performance laser is used to change the reflective properties of the recording layer; this process can be
repeated more than a thousand times.
Pla yba ck a nd recording
DVD+RW (Digital Versatile Disc + ReWritable)
DVD-RW (DVD-Rerecordable)
Wha t is a DVD+R?
DVD+R (Digital Versatile Disc + Recordable)
DVD-R (DVD-Recordable)
Unlike a DVD+RW disc, a DVD+R (write-once DVD) can only be written to once. If it is not finalized after a
recording, further recordings can be added to it. Old recordings can be deleted but they can no longer be
overwritten. The deleted recordings (titles) are marked 'deleted title'.
Pla yba ck only
Before a DVD+R can be played in a DVD player, it must be finalized in the DVD Recorder+VCR. Once this
process is complete, no further recordings can be added.
DVD Video (Digital Versatile Disc)
VCD (Video CD)
Wha t ca n I do w ith m y DVD Recorder+VCR?
Audio CD (Compact Disc Digital Audio)
CD-R (CD recordable) Audio/ CD-RW (CD rewritable) Audio
Video Format : JPEG
Your DVD Recorder+VCR is a machine for recording and playing back digital video discs with ‘two-way‘
compatibility with the universal DVD video standard. This means:
•
•
existing DVD video discs can be played on the recorder.
recordings made on your DVD Recorder+VCR can be played on other DVD video players and DVD-ROM
drives.
Audio Format : CDDA / MP3
Not all recordable CDs may be played by your player.
Du a l Me d ia
Disc-re la te d Te rm s
Supporting Disc
Recording Form a t
Fina lize
±RW / ±R
Title (DVD only)
±Disc + VR format
The main film, accompanying feature content, or music album. Each title is assigned a title reference number
enabling you to locate it easily.
-RW, -R, +R
After fina lize other DVD pla yba ck
Consum er
All disc can playback
Does not need selection (recording format)
Cha pter (DVD only)
Sections of a movie or a musical piece that are smaller than titles. A title is composed of one or several
chapters. Each chapter is assigned a number to enable you to easily locate the chapter you want. Depending on
the disc, chapters may not be labeled.
Rem a rk :
A DVD Recorder+VCR that supports ‘dual media’ recording allows DVD+RW format recording (+VR) on either
DVD-R, DVD-RW, DVD+R or DVD+RW media. Any editing feature that is available with the +RW logical format
is available on any of the media types. This system allows the flexibility for the consumer to use any of the
above media formats for recording in the same system. Since the +VR format is DVD-Video compatible, the
consumer can take any disk recorded on this platform and should be capable of playing it back on the majority
of DVD players on the market.
Tra ck (Audio CD only)
Sections of a movie or a musical piece on an audio CD. Each track is assigned a number, enabling you to easily
locate the track you want.
2
3
O ve rvie w
O ve rvie w
Ab o u t DVD Re co rd in g
Clea ning the Unit
To clean the cabinet
Notes on Recording
Use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with a mild
detergent solution. Do not use strong solvents such as alcohol, benzine, or thinner, as these might damage
the surface of the unit.
•
The recording times shown are not exact because the DVD Recorder+VCR uses variable bit-rate video
compression. This means that the exact recording time will depend on the material being recorded.
When recording a TV broadcast, if the reception is poor or the picture contains interference, the recording
times may be shorter.
•
To obtain a clear picture
The DVD Recorder+VCR is a high-tech, precision device. If the optical pick-up lens and disc drive parts are
dirty or worn, the picture quality will be poor. Regular inspection and maintenance are recommended after
every 1,000 hours of use. (This depends on the operating environment.) For details, please contact your
nearest dealer.
•
•
•
Discs recorded at high speeds (equal to or greater than 2X) may not be recognized.
If you record still pictures or audio only, the recording time may be longer.
The displayed times for recording and time remaining may not always add up to the exact length of the
disc.
Rem ote Control Opera tion Ra nge
•
•
The available recording time may decrease if you heavily edit a disc.
When using a DVD+R disc, you can keep recording until the disc is full, or until you finalize the disc. Before
you start a recording session, check the amount of recording time left on the disc.
Point the remote control at the remote sensor and press the buttons.
Distance: Within 23 ft (7 m) of the remote sensor.
Angle: Within 30° in each direction of the remote sensor.
Rem ote Control Ba ttery Insta lla tion
Recording TV Audio Cha nnels
The DVD Recorder+VCR can record one or two channel audio. For TV broadcasts, this usually means mono or
stereo, but some programs are broadcast with a main and a SAP (Secondary Audio Program) audio channel.
You can record either the main audio or the SAP audio.
Detach the battery cover on the rear of the remote control, and insert two AAA
batteries. Make sure the polarities (+ and -) are aligned correctly.
Ca u tio n
Restrictions on Video Recording
Do not mix old and new batteries. Never mix different types of batteries (standard,
alkaline, etc.).
•
You cannot record copy-protected video using this DVD Recorder+VCR. Copy-protected video includes DVD-
Video discs and some satellite broadcasts. If copy-protected material is encountered during a recording,
recording will pause or stop automatically and an error message will be displayed on-screen.
•
Video that is ‘copy-once only’ can only be recorded using DVD+RW discs with CPRM.
Copyright Notice
N o te s o n Discs
•
Audio and video recordings you make using the DVD Recorder+VCR are for your personal use only. You may
Ha ndling Discs
not sell, lend, or rent them to other people.
Do not touch the playback side of the disc. Hold the disc by the edges
so that fingerprints will not get on the surface. Do not stick paper or
tape on the disc.
•
This product incorporates copyright protection technology that is protected by method claims of certain
U.S.patents and other intellectual property rights owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only unless otherwise authorized by Macrovision
corporation. Reverse engineering or disassembly is prohibited.
Storing Discs
After playing, store the disc in its case.
Do not expose the disc to direct sunlight or sources of heat, or leave it in a parked car exposed to direct
sunlight, as there may be a considerable temperature increase inside the car.
Pre ca u tio n s
Clea ning Discs
Fingerprints and dust on the disc can cause poor picture quality and
sound distortion. Before playing, clean the disc with a clean cloth.
Wipe the disc from the center outward.
Do not use strong solvents such as alcohol, benzine, thinner,
commercially available cleaners, or anti-static spray intended for older
vinyl records.
Ha ndling the Unit
When shipping the unit
Yes
No
The original shipping carton and packing materials come in handy. For maximum protection, re-pack the
unit as it was originally packaged at the factory.
When setting up the unit
The picture and sound of a nearby TV, VCR, or radio may be distorted during playback. In this case, position
the unit away from the TV, VCR, or radio, or turn off the unit after removing the disc.
To keep the surface clean
Ab o u t Sy m b o ls
Do not use volatile liquids, such as insecticide spray, near the unit. Do not leave rubber or plastic products
in contact with the unit for a long period of time. They will leave marks on the surface.
About the
Sym bol
‘
‘ may appear on the TV screen during operation. This icon means the function explained in this User's Guide
is not available on that specific disc.
4
5
Id e n tifica tio n o f Co n tro ls
Id e n tifica tio n o f Co n tro ls
Id e n tifica tio n o f Co n tro ls
Fro n t Pa n e l
!
@
#
$
%
POWER (STANDBY/ ON)
Turns the DVD Recorder+VCR on and off.
Ca ssette Com pa rtm ent (VCR deck )
Insert a video cassette here.
Disc Tra y (DVD deck )
Insert a disc here.
VCR EJECT
Ejects the tape in the VCR deck.
REC
Starts recording. Press repeatedly to set the
recording time.
STOP
Stops playback.
PLAY/ PAUSE
Starts playback of a disc or tape. Pauses playback
or recording temporarily.
REW
DVD: Skips to previous chapter.
VCR: Rewinds the tape during Stop mode. Press
during Play mode for fast reverse picture search.
) Front Pa nel Displa y
!
@
#
Shows the current status of the DVD
Recorder+VCR.
DF-x 5 x x
1
2
COPY
Copies from DVD to VCR (or from VCR to DVD).
PR+/ –
Scans up or down through memorized channels.
Also moves up and down in DVD navigation
menus.
3
SELECT DVD/ VCR
$
^
&
*
)
1 2 3
5
6
Toggles control between the DVD deck and the
VCR deck.
%
(
4
^
&
4
5
OPEN/ CLOSE
Opens or closes the disc tray.
Front AV (VIDEO, L-AUDIO-R)
!
@
#
Connects to the audio/video output of an external
source (VCR, Camcorder, etc.).
DF-x 7 x x
*
(
DV m o d e l o n ly
DV IN
6
Connects to the DV output of an external source
(VCR, Camcorder, etc.).
FF
DVD: Skips to next chapter.
VCR: Advances the tape during Stop mode. Press
during Play mode for fast forward picture search.
$
%
^
&
*
(
)
1 2 3
5
6
4
!
@
#
DF-x 4 x x
$
%
^
&
*
(
)
1 2 3
4
5
6
6
7
Id e n tifica tio n o f Co n tro ls
Id e n tifica tio n o f Co n tro ls
Fro n t Pa n e l Disp la y
Re m o te Co n tro l
Turns the DVD Recorder+VCR on and off.
- Opens and closes the disc tray in DVD mode.
- Ejects the tape in the VCR deck in VCR mode.
Selects VCR mode.
Selects DVD mode.
Switches the DVD Recorder+VCR input to TV tuner, AV1, AV2, FAV or DV.
Cha nnel
- Selects numbered options in menus.
- Selects TV channels.
- Manually adjusts tracking.
TV Channel
PR23
Input m ode
AV1 input
AV2 input
DV input
Au-2
DV
Au-1
Press and hold for 3 seconds to switch between Progressive Scan and
Interlace Scan mode.
DV m o d e l o n ly
Front AV input
F-Au
Resets the tape counter in VCR mode.
Copy
Accesses DVD disc menus.
COPY
DVD to VCR copying
COPY
VCR to DVD copying
Displays or exits the Setup menu.
VCR: Commercial Skip skips forward 30 seconds.
Recording on disc
Indicates a DVD Timer Recording is in
standby mode.
1 1 : 1 5
Indicates a DVD Timer recording is set.
Indicates the DVD is recording.
Recording Pause mode
1 1 : 1 5
0:30
R E C
OTR Recording mode
Displays information about the currently loaded disc, VHS tape, or TV
channel.
RECP
Recording on ta pe
- œ √…† : Selects menu options.
- PR(+/–) : Selects channels.
Indicates a VCR Timer Recording is in
standby mode.
1 1 : 1 5
0:30
1 1 : 1 5
R E C
RECP
Indicates a VCR Timer Recording is set.
Indicates the VCR is recording.
Recording Pause mode
OTR Recording mode
Confirms menu selections.
Selects a subtitle language, if available.
Others
Selects an audio language (DVD), audio channel (CD) or audio type (TV).
Displays the edit menu for DVD+RW/+R discs or sets a chapter marker.
Enlarges the DVD video image.
Indicates when the DVD Recorder+VCR is locked.
SAFE
VCR
Indicates the DVD Recorder+VCR is in
TV mode (set by [TV/VCR] button).
Indicates the DVD Recorder+VCR is in
TV
VCR mode (set by [TV/VCR] button).
Indicates when the DVD Recorder+
VCR is outputting the video signal in
Interlaced Scan mode.
Indicates when the DVD Recorder+ VCR
is outputting the video signal in
Progressive Scan mode.
- Starts playback.
I-S
P-S
- Pauses playback or recording temporarily. Press again to exit Pause mode.
- DVD: Searches backward/forward.
- VCR: Rewinds/advances during Stop mode. Press during Play mode for
fast reverse/forward picture search.
8
9
Id e n tifica tio n o f Co n tro ls
Id e n tifica tio n o f Co n tro ls
Re a r p a n e l
Stops playback or recording.
!
@#
$
^
Skips to the next or previous chapter/track.
Starts recording. Press repeatedly to set the recording time. For more
details, Refer to One Touch Record (OTR) on page 40.
Selects Recording mode: - DVD ; Approx 1 Hour (HQ mode), 2 Hours (SP
mode), 4 Hours (EP mode), 8 Hours (SEP mode)
- VCR : SP or LP.
Increases or decreases the slow motion speed when playing a DVD or VHS
tape.
)
*
(
%
&
Displays the finalize menu for DVD+R discs.
Displays the digest menu for DVD+RW/+R discs.
Displays a disc’s Title menu, if available.
!
@
AC Pow er Cord
Plug into a power outlet.
AUDIO OUT (L, R)
Connect to a TV or other equipment with audio
inputs.
^
&
*
RF IN (FROM ANT.)
Connect to your antenna or cable TV outlet.
RF OUT (TO TV)
Connect to a TV with an RF coaxial input.
COAXIAL (Digita l Audio Out)
Selects a DVD camera angle, if available.
#
$
COMPONENT/ PROGRESSIVE VIDEO OUT (Y Pb Pr)
Connect to a TV with Component Video (Y Pb Pr)
inputs.
Connect to an amplifier with a coaxial digital
audio input.
S-VIDEO OUT
Connect to a TV with an S-Video Input.
RESET Button
Recover from system down.
Switches between the DVD Recorder+VCR tuner and your TV tuner.
Repeats the current chapter, track, title or the entire disc.
Repeats playback between two points (A and B).
Displays the Timer Recording menu.
(
)
Sca rt sock et 2
Connection of an additional device (satellite
receiver, set-top box, video recorder, camcorder,
etc.)
%
Sca rt sock et 1
Connection of a TV set. Composite-output and
RGB-output
Pro g re ssive Sca n Mo d e
•
If your TV supports Progressive Scan, you can view high quality video by setting the
DVD Recorder+VCR to Progressive Scan mode. If your TV does not support
Progressive Scan, do NOT change to Progressive Scan mode.
If you do so accidentally, press and hold the [P.SCAN] button for 3 seconds to restore
normal viewing.
Ca u tio n
•
Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage
to the DVD Recorder+VCR.
•
•
When video output mode is changed from RGB to Interlace or Progressive (Scart 1)
will not be correct colour for Component video.
As component outputs have their own Jacks on the back side, change the TV input
into Component input, after connecting the component cables from the DVD
Recorder+VCR to TV.
•
Changing from Interlace or Progressive to RGB, should be the opposite of above.
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS
ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO
BE DISPLAYED IN THE PICTURE. IN CASE OF 525 PROGRESSIVE SCAN PICTURE
PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION
TO THE 'STANDARD DEFINITION' OUTPUT. IF THERE ARE QUESTIONS REGARDING
OUR TV SET COMPATIBILITY 'WITH THIS MODEL 525p DVD PLAYER, PLEASE
CONTACT OUR CUSTOMER SERVICE CENTER.
1 0
1 1
Co n n e ctio n s
Co n n e ctio n s
Co n n e ctio n s
•
•
•
There are a variety of ways to connect the DVD Recorder+VCR to your TV and other equipment. Use only one of
Co n n e ctin g a TV
the connections described below. Whichever TV connection you use will work with all input sources.
Please refer to the manuals for your TV, VCR, stereo system, or other devices as necessary to make the best
connections.
For better sound reproduction, connect the DVD Recorder+VCR’s AUDIO OUT jacks to the audio in jacks of your
amplifier, receiver, stereo, or audio/video equipment. See ‘Connecting an Amplifier/Receiver‘ on page 13.
Choose one of the following TV connections, depending on the capabilities of your equipment.
RF Connection
Connect the RF OUT (TO TV) jack on the DVD Recorder+VCR to the antenna in jack on your TV using the supplied
75-ohm RF cable (R). If you use this connection, tune your TV to the DVD Recorder+VCR's RF output channel
(CH52).
Ca u tio n
•
•
•
Make sure the DVD Recorder+VCR is connected directly to the TV, and the TV is set to the correct video input.
Rear of TV
Do not connect the DVD Recorder+VCR’s AUDIO OUT jack to the phono in jack (record deck) of your audio system.
Do not connect the DVD Recorder+VCR via your VCR. The DVD image could be distorted by the copy protection
system.
Sca rt Connection
S-VIDEO
INPUT
ANTENNA
INPUT
COMPONENT/PROGRESSIVE VIDEO INPUT
Y
Pr
Pb
1
Plug a scart cable into the scart socket EURO AV1 at
the back of the DVD Recorder+VCR and the
corresponding scart socket at the back of the TV set.
(V)
C
S
V
R
2
Plug a scart cable into the blue scart socket EURO
AV2/DECODER at the back of the DVD Recorder+VCR
and the corresponding scart socket at the back of a
satellite decoder or set top box.
Co n n e ctin g An te n n a / Ca b le
S-Video Connection
1
Disconnect the antenna/cable from the rear of your TV.
Antenna
Antenna
1
Connect the S-VIDEO OUT jack on the DVD
Recorder+VCR to the S-Video in jack on your TV using
an S-Video cable (S).
2
Connect this cable to the jack marked ANT IN (FROM ANT.)
on the rear panel of the DVD Recorder+VCR.
Rear of DVD Recorder+VCR
Cable TV
Wall Jack
Flat Wire
(300ohm)
2
Connect the Left and Right AUDIO OUT jacks from the DVD Recorder+VCR to the left/right audio in jacks on
your TV using the supplied audio cables.
OR
OR
300/75ohm Adapter
(Not supplied)
Com ponent Video Connection
1
Connect the COMPONENT/PROGRESSIVE VIDEO OUT jacks on the DVD Recorder+VCR to the corresponding
input jacks on your TV using a Y Pb Pr cable (C) if the Component Video jacks (Y, Pb, Pr) are available on
your TV.
2
Connect the Left and Right AUDIO OUT jacks from the DVD Recorder+VCR to the left/right audio in jacks on
your TV using the supplied audio cables.
Rear of DVD Recorder+VCR
Progressive Sca n Connection
•
If your television is a high-definition or ‘digital ready‘ television, you may take advantage of the DVD
Recorder+VCR’s Progressive Scan output for the highest video resolution possible.
If your cable wire is connected to your TV without a converter or descrambler box, unscrew the wire from your
TV and attach it to the ANT IN (FROM ANT.) jack on the rear panel of the DVD Recorder+VCR.
•
If your TV does not accept the Progressive Scan format, the picture will appear scrambled.
Use the supplied coaxial cable to connect between the DVD Recorder+VCR’s OUT (TO TV) jack and the antenna
input jack on your TV. With this connection, you can receive all midband, superband, and hyperband channels
(all cable channels).
1
2
Connect the COMPONENT/PROGRESSIVE VIDEO OUT jacks on the DVD Recorder+VCR to the corresponding
in jacks on your TV using an optional Y Pb Pr cable (C).
Connect the Left and Right AUDIO OUT jacks from the DVD Recorder+VCR to the left/right audio in jacks on
your TV using the supplied audio cables.
•
•
Be sure to set the DVD Recorder+VCR to Progressive Scan mode by pressing and holding [P.SCAN] for 3 seconds
(or changing the Video Output in the Setup Menu; see page 23).
Progressive Scan does not work with the RF, Audio/Video or S-Video connections.
1 2
1 3
Co n n e ctio n s
Co n n e ctio n s
Co n n e ctin g a n Am p lifie r/ Re ce ive r
Co n n e ctin g O p tio n a l Eq u ip m e n t
Jack Panel of Accessory Component
(VCR, Camcorder, etc.)
To receive audio/video signals from other equipment, connect
the AVF jacks on the DVD Recorder+VCR to the audio/video
out jacks on your external component, using optional
audio/video cables.
Connecting to a n a m plifier equipped w ith tw o cha nnel a na log stereo or Dolby Pro Logic ll/ Pro Logic
Connect the Left and Right AUDIO OUT jacks on the DVD Recorder+VCR to the left and right audio in jacks on
your amplifier, receiver, or stereo system, using the supplied audio cables (A).
Connecting to a n a m plifier equipped w ith tw o cha nnel digita l stereo (PCM) or to a n Audio/ Video receiver equipped
w ith a m ulti-cha nnel decoder (Dolby Digita l™, MPEG 2 , or DTS)
1
Connect the DVD Recorder+VCR’s DIGITAL AUDIO OUT jack (COAXIAL X) to the corresponding in jack on
your amplifier. Use an optional digital coaxial audio cable.
2
You will need to activate the DVD Recorder+VCR’s digital output; see ‘AUDIO Settings‘ on page 24.
Digita l Multi-Cha nnel Sound?
A digital multi-channel connection provides the best sound quality. For this you need a multi-channel
audio/video receiver that supports one or more of the audio formats supported by your DVD Recorder+VCR
(MPEG 2, Dolby Digital, and DTS). Check the receiver manual and the logos on the front of the receiver.
•
Due to the DTS Licensing agreement, the digital output will be in DTS digital out when DTS audio stream is
selected.
•
•
•
If the audio format of the digital output does not match the capabilities of your receiver, the receiver will produce
a strong, distorted sound or no sound at all.
5.1 channel digital surround sound via the digital connection can only be obtained if your receiver is equipped with
a digital multi-channel decoder.
Front of DVD Recorder+VCR
To see the audio format of the current DVD on the on-screen display, press [AUDIO].
The DVD Recorder+VCR does not perform internal (2- channel) decoding of DTS sound tracks. To enjoy DTS multi-
channel surround, you must connect the DVD Recorder+VCR to a DTS compatible receiver via one of the DVD
Recorder+VCR’s digital audio outputs.
DV m o d e l o n ly
Co n n e ctin g a Dig ita l Ca m co rd e r
Using the front panel DV IN jack, it is possible to connect a DV digital camcorder, video deck or DVD+R/RW
recorder and digitally transfer DV tapes or DVD+R/RW discs to DVD+R/RW.
Rear of DVD Recorder+VCR
Use a DV cable (not supplied) to connect the DV In/Out jack of your DV camcorder/video deck to the front panel
DV IN jack of the DVD Recorder+VCR.
DV Digital Camcorder
This jack is for connection to DV equipment only. It is not
compatible with digital satellite tuners or D-VHS video
DV
IN/OUT
decks.
A
X
L
R
COAXIAL
AUDIO INPUT
DIGITAL INPUT
Amplifier (Receiver)
D
Front of DVD Recorder+VCR
1 4
1 5
In itia l In sta lla tio n
In itia l In sta lla tio n
In itia l Se tu p
In itia l Se tu p
After successfully connecting your DVD Recorder+VCR to your TV and other devices, this chapter will show you
how to complete the initial installation.
Se tu p Me n u O ve r vie w
The DVD Recorder+VCR Setup menu includes four categories, including: Initial Setup, Disc Operation, Disc Edit
and Timer Recording. Press [SETUP], [œ/√] and [ENTER] on the remote control to view the first and second
levels of the Setup menu.
You must follow the initial installation process to set the time, date, channels, and language preferences for the DVD
Recorder+VCR.
1
‘Initial Setup Wizard‘ is displayed on the screen. Make sure the RF cable
from your antenna or cable TV jack is connected. Press [ENTER] to begin
initial installation.
Initial Setup Wizard
1/7
1 . Initia l Setup Screen
2 .
Disc Opera tion Screen
go to page 47~49.
Before using your recorder
Please complete this setup
go to page 17~28.
Next
2
3
4
5
'OSD Lang' message is displayed on the screen. Select the desired language
for the on screen menu using […/†]. Press [ENTER] to confirm.
ENTER OK
DVD Recorder
Init Setup ➝
DVD Recorder
Init Setup ➝
Init Setup
œ √ Select
Disc Operation
œ √ Select
OSD Lang
2/7
'Country Setting' message is displayed on the screen. Select the desired
country using […/†]. Press [ENTER] to confirm.
√
English
Français
Español
Init Setup
Disc Oper
Disc Edit
Timer REC
Init Setup
Disc Oper
Disc Edit
Timer REC
'Auto Scan' message is displayed on the screen. The DVD Recorder+VCR
detects channels automatically and stores them in memory.
Back
…† Choose
ENTER OK
3 . Disc Edit Screen
4 .
Tim er Recording Screen
'Clock Set' message is displayed on the screen.
Set the clock.
go to page 50~52.
go to page 42~44.
Country Setting 3/7
France
√
Germany
Greece
Use [œ/√] to move left/right and use […/†] to change the settings.
DVD Recorder
Init Setup ➝
DVD Recorder
Init Setup ➝
After setting the clock, press [ENTER] to confirm. If you cancel the process
during Initial Installation, you should repeat this procedure.
Back
Disc Edit
œ √ Select
Timer REC
œ √ Select
…† Choose
ENTER OK
Init Setup
Disc Oper
Disc Edit
Timer REC
Init Setup
Disc Oper
Disc Edit
Timer REC
6
7
'Adjust channels' message is displayed on the screen. Press [ENTER] to
confirm.
Auto Scan
4/7
Antenna
'Complete' message is displayed on the screen. 'Initial Installation' process is
finished.
5 CHs found
Back
Cancel
œ √ Choose
ENTER OK
Re -In sta lla tio n
This set is equipped with the multi-tuner for receiving many countries' broadcasting.
In order to receive broadcasting of different countries, follow as below.
‘In sta lla tio n ’ Se ttin g s
Ma nua l Setting
To complete the set-up of your DVD Recorder+VCR when the auto set has
not stored all of the channels or when you wish to store a new channel.
Clock Set
5/7
1
Press [SETUP] and select the 'Restore Defaults' using [œ /√]. Then, RESET the
set. (see page 28)
…
1
†
/
1
/ 2005 00 : 00
2
3
Power On, then you see the 'Initial Installation'.
Select the country which you want to, then repeat the steps as above.
Back
Installation
…† Choose
ENTER OK
• Manual Set
Auto Scan
Clock Set
1
Press [SETUP]. The Setup menu appears.
Adjust channels
6/7
Adjust channels
While ‘Init Setup‘ is selected, press [ENTER] to go to the initial setup
page.
…
NO. NAME
OK
Cancel
Back
PR1 BBC
PR2 P-02
PR3 P-03
…
†
2
3
4
5
Use [œ/√] to select ‘Installation‘.
œ
√
ENTER
SETUP
Exit
Choose
OK
†
While ‘Installation‘ is selected, press [†] to select ‘Manual Set‘.
Press [ENTER]. The ‘Manual Set’ menu appears.
Select ‘Standard‘ using [œ/√].
œ √ Choose
ENTER OK
Manual Set
Complete
7/7
Standard
…
Reception
Aerial
Auto Search
25
Fine Tune
0
Setup has been completed
Enjoy using your recorder
PAL BG
†
Use […/†] to select the desired ‘Standard’ (PAL BG, PAL DK, PAL II, or
SECAM L).
Decoder
Off
Store Channel
NAME
P-04
PR No.
4
Back
Finish
Store
Cancel
ENTER OK
This set is equipped with the Multi-Tuner. You can search broadcastings of
other countries. If the set can not search the channels, please Re-Install. (see
page 16.)
1 6
1 7
In itia l Se tu p
In itia l Se tu p
Manual Set
Standard
6
Select ‘Reception‘ using [œ/√].
Auto Sca n
Reception
…
Auto Search
Fine Tune
0
The DVD Recorder+VCR has a frequency synthesized tuner capable of
receiving up to 119 channels. These include VHF channels 2-20, 74-80, UHF
channels 21-69 and CATV channels 1-41.
PAL BG
Cable
†
- -
Use […/†] to select the desired broadcast system (Aerial or Cable).
Installation
Decoder
Off
Store Channel
NAME
P-04
Manual Set
• Auto Scan
Clock Set
Aeria l: If you are using a standard antenna to receive channels.
Ca ble: If you are using basic cable to receive channels.
Select ‘Auto Search‘ using [œ/√].
PR No.
- -
Store
Adjust channels
Cancel
Prepa ra tion:
Connect the DVD Recorder+VCR to the desired type of antenna or cable TV
system, as shown in ‘Connecting Antenna/Cable‘ on page 11.
Manual Set
Standard
7
8
Reception
Aerial
Auto Search
…
Fine Tune
0
…
†
œ
√
ENTER
SETUP
Choose
OK
Exit
Search the real channel number by pressing […/†].
PAL BG
25
†
1
2
3
Follow steps 1-2 as shown under ‘Manual Set’.
Auto Scan
TV
Decoder
Off
Store Channel
NAME
P-04
PR No.
4
While ‘Installation‘ is selected, press […/†] to select ‘Auto Scan‘.
Press [ENTER] to begin the channel search.
Store
1 CHs found
Cancel
Manual Set
Standard
Select ‘Fine Tune‘ using [œ/√]. You can adjust the fine tuning by
pressing […/†].
The tuner will automatically search for all available channels in your area
and place them in the tuner’s memory.
Reception
Aerial
Auto Search
25
Fine Tune
…
0
PAL BG
†
Decoder
Off
Store Channel
NAME
P-04
PR No.
4
•
After Auto Scan is complete, follow the instructions above to make sure that Tuning Band is set correctly.
Store
Cancel
Manual Set
Standard
Clock Set
Reception
Aerial
Auto Search
25
Fine Tune
0
9
Select ‘Decoder‘ using [œ/√].
PAL BG
1
2
Follow steps 1-2 as shown under ‘Manual Set’.
When the program is encoded (and you have a decoder connected to
socket EURO AV2), press […/†] to select ‘On’ .
Installation
Decoder
…
Store Channel
NAME
P-04
PR No.
4
Use […/†] to select ‘Clock Set‘.
Manual Set
Auto Scan
• Clock Set
Off
†
Store
Cancel
Adjust channels
Manual Set
Standard
1 0 Select ‘Store Channel‘ using [œ/√].
Reception
Aerial
Auto Search
25
Fine Tune
0
…
†
PAL BG
œ
√
ENTER
SETUP
Exit
Choose
OK
Use […/†] to select program number to store and press [ENTER].
Decoder
Off
Store Channel
NAME
Clock Set
PR No.
3
4
Press [ENTER]. The ‘Clock Set’ menu appears.
…
…
1
Store
4
†
P-04
1
2005
00 40
Cancel
†
Enter the date and time.
Manual Set
Standard
œ /√ (left/right): Moves the cursor to the previous or next column.
…/† (up/down): Changes the setting at the current cursor position.
1 1 Select ‘Program Name‘ using [œ/√]. Press [ENTER] to move to the
second level. If your DVD Recorder+VCR is showing no station name or
is showing a station name incorrectly, you can correct this.
Reception
Aerial
Auto Search
25
Fine Tune
0
PAL BG
Decoder
Off
Store Channel
NAME
5
Press [ENTER] to confirm your setting, then press [SETUP] to exit the Setup
menu.
PR No.
4
You can create the station name and enter a 4-digit name. Change the
Store
P-04
Cancel
letters with the […/†], move the next letter with the [œ/√].
Program Name
P-04
NB. You must backspace any digits already in the name box before
you can enter a new name.
A
H
O
B
I
C
J
D
K
E
L
S
F
M
T
G
N
U
P
V
Q
W
R
X
Y
Z
Clear
Space
OK
Cancel
1 8
1 9
In itia l Se tu p
In itia l Se tu p
‘Re co rd in g O p tio n s’ Se ttin g s
DVD Record Qua lity
Adjust Cha nnels
Installation
You can set the default DVD recording quality to: HQ (High Quality - 1
hr/disc), SP (Standard Quality - 2 hrs/disc), EP (Extended Play - 4 hrs/disc) or
SEP (Very Low Quality - 8 hrs/disc).
1
2
3
4
Follow steps 1-2 as shown under ‘Manual Set’.
Use […/†] to select ‘Adjust Channels‘.
Manual Set
Auto Scan
Clock Set
Recording Options
• DVD Quality
VCR Quality
Auto Chapter
Overwrite
HQ
SP
EP
SEP
• Adjust channels
Press [ENTER]. The ‘Adjust channels’ menu appears.
1
Press [SETUP]. The Setup menu appears.
Use […/†] to select the PR number you want to adjust. Then press
[ENTER].
While ‘Init Setup‘ is selected, press [ENTER] to go to the initial setup
page.
…
†
œ
√
ENTER
SETUP
Choose
OK
Exit
…
†
œ
√
ENTER
SETUP
Choose
OK
Exit
Adjust channels
NO.
PR1
PR2
PR3
PR3
PR3
PR3
NAME
2
3
4
5
6
Use [œ/√] to select ‘Recording Options
‘.
…
OK
BBC
P-02
P-03
P-03
P-03
Cancel
While ‘Recording Options ‘ is selected, press [†] to select ‘DVD Quality‘.
P-03
Press [√] to move to the second level.
†
…
†
ENTER
œ
√
Select
Move
Use […/†] to to select the desired Record Quality (HQ SP, EP or SEP).
,
Delete
Adjust channels
After tuning TV stations into your DVD Recorder+VCR, you may wish to delete a
station.
Press [ENTER] to confirm your selection, then press [SETUP] to exit the menu.
NO.
PR1
PR2
PR3
PR3
PR3
PR3
NAME
BBC
P-02
- -
- -
- -
…
OK
Cancel
VCR Record Qua lity
You can set the default VCR recording quality to SP (Standard Play) or LP
(Long Play). SP is higher quality, but LP provides 2 times the recording time;
e.g., a 2 hour tape will record for 4 hours in LP mode.
1
2
3
Select the PR number you want to delete using […/†].
Press [œ]. The selected PR will be deleted.
Select ‘OK’ to exit.
- -
†
Recording Options
➝
œ
Delete
Edit
DVD Quality
• VCR Quality
Auto Chapter
Overwrite
ENTER
…†
Move
Confirm
SP
LP
Follow the same procedure as the ‘DVD Record Quality’.
Edit
Label
After tuning TV stations into your DVD Recorder+VCR, you may wish to
put a name into any channel you want to.
- - - -
…
†
œ
√
ENTER
SETUP
Choose
OK
Exit
a
j
b
k
c
l
d
e
f
g
h
q
v
i
m
n
o
t
p
u
r
Clear
OK
Cancel
1
2
3
Select the PR number you want to edit using […/†].
Press [➝]. You can put a name by pressing […/†] and [œ /√].
Select ‘OK’ to exit.
Space
z
s
w
Auto Cha pter
x
y
_
-
Backspace
During recording, chapter markers are added automatically at fixed
intervals.
You can set this interval to 5 m in
But when you set DVD Record quality “SEP”, Auto Chapter interval could be
set only ‘10 min’ or ‘15 min’.
To turn off automatic chapter marking, select ‘Off ‘.
A’
a
Symbol
Recording Options
…
†
0-9
Input digits
Prev Page
Backspace
Next Page
œ
√
Select
œœ
DVD Quality
VCR Quality
• Auto Chapter
Overwrite
§
∞
Off
,
1 0 m in or 1 5 m in
.
05 min
10 min
15 min
Sort cha nnels
After tuning TV stations into your DVD Recorder+VCR, you may wish to change
the order of PR's you have in your set, as your preference.
…
†
œ
√
ENTER
SETUP
Choose
OK
Exit
Follow the same procedure as ‘DVD Record Quality’.
1
2
3
4
Select the PR number you want to move using […/†].
Press […/†] to select the PR number you want to move to.
Press [ENTER]. The selected PR Will be moved to the new PR number.
Select ‘OK’ to exit.
Overw rite
Immediately begins recording over the currently selected title.
Recording Options
DVD Quality
VCR Quality
Auto Chapter
Overwrite
• On
Off
…
†
œ
√
ENTER
SETUP
Choose
OK
Exit
2 0
2 1
In itia l Se tu p
In itia l Se tu p
‘La n g u a g e ’ Se ttin g s
OSD La ngua ge
Select a language for the DVD Recorder+VCR Setup menu and on-screen
displays.
‘Pre fe re n ce s’ / Vid e o Se ttin g s
1
Press [SETUP]. The Setup menu appears.
Preferences
• Video
Audio
Parental Ctrl
Auto Settings
VCR
TV Aspect
Video Output
4:3 PS
Interlace
While ‘Init Setup‘ is selected, press [ENTER] to go to the initial setup
page.
Language
• OSD Lang
Disc Menu
Subtitle
English
Modulator Out
Français
Español
Portugues
Italiano
Deutsch
Nederlands
Magyar
†
†
1
Press [SETUP]. The Setup menu appears.
2
3
4
Use [œ/√] to select ‘Preferences
While ‘Preferences ‘ is selected, press [†] to select ‘Video‘.
Press [√]. The ‘Video‘ submenu is displayed.
‘.
Audio
While ‘Init Setup‘ is selected, press [ENTER] to go to the initial setup
page.
…
†
œ
√
ENTER
SETUP
Choose
OK
Exit
…
†
œ
√
ENTER
SETUP
Choose
OK
Exit
2
3
4
5
6
Use [œ] and [√] to select ‘Language
‘.
While ‘Language‘ is selected, press [†] to select ‘OSD Lang‘.
Press [√] to move to the second level.
TV Aspect Ra tio
1
Use […/†] to select ‘TV Aspect‘ while the ‘Video‘ submenu is
displayed.
Use […/†] to select the desired language.
Preferences
Video
Audio
Parental Ctrl
Auto Settings
VCR
•
TV Aspect
Video Output
4:3 PS
4:3 LB
16:9
Press [ENTER] to confirm your selection, then press [SETUP] to exit the menu.
2
3
4
5
Press [√] to go to the second level.
Use […/†] to select the desired TV Aspect.
Press [ENTER] to confirm your selection.
Press [SETUP] to exit the menu.
Modulator Out
Menu/ Subtitle/ Audio La ngua ge
Select your preferred language for Disc Menus, Subtitles, and Audio
soundtracks.
…
†
œ
√
ENTER
SETUP
Choose
OK
Exit
Language
OSD Lang
• Disc Menu
Subtitle
Audio
Auto
English
French
Spanish
Portuguese
Italian
Follow the same procedure as the OSD Language.
4 :3 PS : Select when a standard 4:3 TV is connected. Displays pictures cropped to fill your TV screen. Both
sides of the picture are cut off.
German
Dutch
†
†
4 :3 LB : Select when a standard 4:3 TV is connected. Displays theatrical images with masking bars above and
below the picture.
…
†
œ
√
ENTER
SETUP
Choose
OK
Exit
1 6 :9 : Select when a 16:9 wide screen TV is connected.
Language
OSD Lang
Disc Menu
• Subtitle
Audio
Off
English
French
Spanish
Portuguese
Italian
Video Output
German
Dutch
†
†
Progressive Scan Video provides the highest picture quality with reduced
flickering.
…
†
œ
√
ENTER
SETUP
Choose
OK
Exit
Preferences
Video
Audio
Parental Ctrl
Auto Settings
VCR
TV Aspect
Video Output
•
Interlace
Progressive
RGB
Interla ce or Progressive : If you connect the DVD Recorder+VCR to a digital
television (DTV) or Monitor using the COMPONENT jacks, set Video Output
to ‘Interlace’ or ‘Progressive’.
Language
OSD Lang
Disc Menu
Subtitle
• Audio
Modulator Out
Auto
English
French
Spanish
Portuguese
Italian
…
†
œ
√
ENTER
SETUP
Choose
OK
Exit
RGB : If you connect the DVD Recorder+VCR to a analog television using
the SCART jacks, set Video Output to ‘RGB’.
Follow the same procedure as TV Aspect Ratio to change the Video Output.
German
Dutch
†
†
…
†
œ
√
ENTER
SETUP
Choose
OK
Exit
Ca u tio n
Once the Progressive Scan setting is entered, an image will only be visible on a Progressive Scan compatible TV or
monitor.
2 2
2 3
In itia l Se tu p
In itia l Se tu p
‘Pre fe re n ce s’ / Au d io Se ttin g s
‘Pre fe re n ce s’ / Pa re n ta l Co n tro ls
Set Pa renta l Level
The Parental Controls feature allows you to prevent DVDs from being played based on their ratings or to have
certain discs played with alternative scenes. You can set the parental level from ‘ADULT’ to ‘KID SAFE’.
1
Press [SETUP]. The Setup menu appears.
Preferences
Video
• Audio
Parental Ctrl
Auto Settings
VCR
Digital Output
Dynamic Range
BItstream
While ‘Init Setup‘ is selected, press [ENTER] to go to the initial setup
page.
Modulator Out
1
Press [SETUP]. The Setup menu appears.
2
3
4
Use [œ/√] to select ‘Preferences
While ‘Preferences ‘ is selected, press [†] to select ‘Audio‘.
Press [√]. The ‘Audio‘ submenu is displayed.
‘.
Preferences
Video
Audio
• Parental Ctrl
Auto Settings
VCR
While ‘Init Setup‘ is selected, press [ENTER] to go to the initial setup
page.
…
†
œ
√
ENTER
SETUP
Choose
OK
Exit
Parental
Password
Modulator Out
2
3
Use [œ/√] to select ‘Preferences
‘.
While ‘Preferences
Ctrl‘.
‘ is selected, press [†] to select ‘Parental
…
†
œ
√
ENTER
SETUP
Exit
Choose
OK
Digita l Output
4
Press [√]. The ‘Parental‘ submenu is displayed.
1
Use […/†] to select ‘Digital Output‘ while the Audio submenu is
displayed.
Preferences
Preferences
Video
Audio
Parental Ctrl
Auto Settings
VCR
Video
Audio
Parental Ctrl
Auto Settings
VCR
1 Kid Safe
2 G
3 PG
4 PG-13
5 PGR
6 R
7 NC-17
8 Adult
SETUP
Exit
•
Digital Output
Dynamic Range
Off
Bitstream
LPCM
• Parental
Password
2
3
4
5
Press [√] to go to the second level.
Use […/†] to select the desired digital output type.
Press [ENTER] to confirm your selection.
Press [SETUP] to exit the menu.
Modulator Out
Modulator Out
…
†
œ
√
ENTER
…
†
Choose
OK
œ
√
ENTER
SETUP
Choose
OK
Exit
Input Password
Password
5
The Password Input dialog will appear. Enter a 4-digit password using the [0-9]
buttons. If this is the first time you have entered a password, you will be prompted to
enter the password again to confirm it.
Off
OK
0-9
…
Cancel
ENTER
No signal will be output from the Digital Audio Out jacks.
Input digits
œ
√
†
Select
OK
The initial password is ‘3308‘. You must enter this password before you can
change the Parental Level.
Bitstrea m
Select when connected to a Dolby Digital or DTS decoder (or an amplifier or other equipment with a Dolby
Digital or DTS decoder).
Preferences
Video
Audio
Parental Ctrl
Auto Settings
VCR
After setting the password, press [ENTER].
1 Kid Safe
2 G
3 PG
4 PG-13
5 PGR
6 R
Parental
Password
LPCM
Modulator Out
Select when connected to a digital amplifier. The DVD Recorder+VCR's digital audio signal will be output in the
PCM format when you play a DVD recorded with a Dolby Digital (only for DVD) or MPEG soundtrack. If the DVD
is recorded with a DTS sound track then no sound will be heard.
7 NC-17
• 8 Adult
…
†
œ
√
ENTER
SETUP
Choose
OK
Exit
6
7
Enter your new password.
Input Password
New Password
Dyna m ic Ra nge
OK
Cancel
ENTER
While watching DVD movies, you may wish to compress the dynamic range
of the audio output (the difference between the loudest and quietest
passages). This allows you to listen to a movie at a lower volume without
losing clarity of sound.
Set 'Dynamic Range'to anymode you want for this effect.
0-9
Input digits
Select
…
†
Preferences
œ
√
OK
Video
Audio
Parental Ctrl
Auto Settings
VCR
Digital Output
Dynamic Range
–
–
–
–
–
–
–
–
–
–
FULL
1/2
Use […/†] to select the desired parental level and press [ENTER] to
confirm.
Preferences
Modulator Out
Video
Audio
OFF
1 Kid Safe
2 G
3 PG
4 PG-13
5 PGR
6 R
Parental Ctrl
Auto Settings
VCR
Parental
Password
Adult to Kid Sa fe : Some discs contain scenes not suitable for children.
If you set a rating for the DVD Recorder+VCR, all scenes with the same
rating or lower will be played. Higher rated scenes will not be played
unless an alternative scene is available on the disc. The alternative
must have the same rating or a lower one. If no suitable alternative is
Follow the same procedure as ‘Digital Output‘ to set the Dynamic Range.
…
†
œ
√
ENTER
SETUP
Exit
Choose
OK
Modulator Out
7 NC-17
• 8 Adult
…
†
œ
√
ENTER
SETUP
Choose
OK
Exit
found, playback will stop. You must enter the 4-digit password or change the rating level in order to play
the disc.
8
Press [ENTER] to confirm your rating selection, then press [SETUP] to exit the menu.
2 4
2 5
In itia l Se tu p
In itia l Se tu p
Cha nge Pa ssw ord
VPS/ PDC
VPS/PDC is a service provided by some stations to enable you to perform
timer recordings precisely even if the broadcaster delays the start time of
the programme slightly. The time you enter is the VPS/PDC time so this
must be correct. Not all stations offer VPS/PDC, in which case the player
will start at the time you enter and not the actual start time of the
programme.
If you wish to start recording at a specific time without it being adjusted by
the VPS/PDC system in the event of a delay, switch VPS/PDC off otherwise
the player will not record.
1
While ‘Preferences
Ctrl‘.
‘ is selected, press [†] to select ‘Parental
Preferences
Preferences
Video
Audio
Parental Ctrl
Auto Settings
VCR
Video
Audio
Parental Ctrl
Auto Settings
VCR
Parental
Password
2
Press [√] to select ‘Password‘. Then press [ENTER].
Auto Clock Set
VPS/PDC
•
Change
•
On
Off
Modulator Out
Modulator Out
…
†
…
†
œ
√
ENTER
SETUP
Choose
OK
Exit
œ
√
ENTER
SETUP
Choose
OK
Exit
3
4
The ‘Input Password’ submenu appears. Enter your current 4-digit
password then press [ENTER].
Input Password
Old Password
New Password
Confirm PWD
OK
Follow the same procedure as ‘Auto Clock Set’ to set the ‘VPS/PDC’ status.
Enter a new 4-digit password, then press [ENTER]. Re-enter the new password to
confirm, press [ENTER].
Cancel
ENTER
0-9
Input digits
Select
…
†
œ
√
OK
•
"VPS/PDC" and "Auto Clock Set" are not provided for some countries.
•
•
Ma ste r Pa ssw o rd
control and then press [ENTER].
Set the new password to something other than '0000'.
:
If you forget your password, press 3,3,0,8 on the remote
Pre fe re n ce s / VCR
This feature enables you to search for Index marks or specific times on your
VHS tapes.
Preferences
Video
Audio
1
2
3
4
5
While ‘Preferences‘ is selected, press [†] to move to the second level.
Use […/†] to select ‘VCR‘.
Parental Ctrl
Auto Settings
• VCR
Index+
Index-
Go to Zero
Modulator Out
Va rio u s ‘Pre fe re n ce s’ Se ttin g s
Press [ENTER] to display the submenu.
…
†
œ
√
ENTER
SETUP
1
Press [SETUP]. The Setup menu appears.
Choose
OK
Exit
Select ‘Index+’, ‘Index–’ or ‘Go to Zero’.
While ‘Init Setup‘ is selected, press [ENTER] to go to the initial setup
page.
Preferences
Video
Audio
Parental Ctrl
• Auto Settings
VCR
If you select ‘Index+’ (or ‘Index–’) and press [ENTER], your DVD
Recorder+VCR will locate your index mark and begin playback.
Preferences
Video
Audio
Parental Ctrl
Auto Settings
VCR
Auto Clock Set
VPS/PDC
Off
Off
2
3
Use [œ/√] to select ‘Preferences
‘.
Modulator Out
6
If you select ‘Go-To Search’ and press [ENTER], your DVD
Recorder+VCR will wind to the position 0:00:00 and stop.
•
Index+
Index-
Go to Zero
While ‘Preferences
Settings‘.
‘ is selected, press [†] to select ‘Auto
Modulator Out
…
†
œ
√
ENTER
SETUP
Exit
Choose
OK
…
†
œ
√
ENTER
SETUP
Choose
OK
Exit
4
Press [√]. The ‘Auto Settings‘ submenu is displayed.
•
The VCR menu is activated only when a video cassette tape is inserted.
Auto Clock Set
Auto Clock enables the DVD Recorder+VCR to set the clock automatically
whenever it is in Standby mode (plugged in but powered off).
Preferences
Pre fe re n ce s / Mo d u la to r O u t
Video
Audio
Parental Ctrl
Auto Settings
VCR
Auto Clock is only available for models with the VPS/PDC function.
Some broadcasting stations may send the time and date along with the VPS/PDC
data. The video will automatically use this time and date during the initial setting up
procedure during normal use, and every time you switch the video off at the mains.
If you find that this time and date is incorrect you can remove this feature by
following the steps below changing it to the OFF mode, you will then have to
manually set the time and date, see above.
• Auto Clock Set
VPS/PDC
On
Off
You can change the modulator out channel using the [0-9] buttons.
Preferences
Modulator Out
Video
Audio
Parental Ctrl
Auto Settings
VCR
•
"Modulator Out" is not provided for france.
…
†
œ
√
ENTER
SETUP
Exit
Choose
OK
• Modulator Out
…
†
œ
√
ENTER
SETUP
Choose
OK
Exit
1
2
Use […/†] to select 'Auto Clock Set' and press [ENTER].
Use […/†] to change the 'Auto Clock Set' status, and press [ENTER] to confirm.
Modulator Out
Channel
OK
œ
52
√
Cancel
2 6
2 7
In itia l Se tu p
O n -Scre e n Disp la y O ve r vie w
O n -Scre e n Disp la y O ve r vie w
The On-Screen Display provides feedback on the status of the DVD Recorder+VCR and/or the currently loaded
disc. To access the On-Screen Display (or OSD), press the [DISPLAY] button.
Sy ste m In fo rm a tio n
System Information helps service personnel identify key firmware
information about your DVD Recorder+VCR in case service is required.
System Info
Version
WP3000000FQ-050813
Loader Version
AA003 A100
1.0.6
Micom Software
DivX®
Disp la y in g DVD In fo rm a tio n
√√
Registration code
WWJR3845
During disc playback, press [DISPLAY] to show information about the current
disc.
…
†
œ
√
ENTER
SETUP
Exit
Choose
OK
Re sto re De fa u lts
Cha nging m enu options in displa y m enu
If you wish, you can reset the DVD Recorder+VCR to its original factory
settings.
Restore Defaults
1
2
3
Press [DISPLAY] during playback. The on-screen display appears on the TV screen.
Use [œ√] to select the desired icon on the on-screen display. Press [ENTER] to display a submenu.
Use […†] to change the numbers. Press [ENTER] to confirm.
•
Default
Reset
1
2
3
4
Press [SETUP].
Use [œ/√] to select ‘Restore Defaults
Press [ENTER].
‘.
…
†
œ
√
ENTER
SETUP
Exit
Choose
OK
•
Displa ying icons on DVD/ CDDA disc
The Initialize menu will appear. Use the […†œ √] buttons to select
‘RESET‘ and press [ENTER].
Title : Shows the current title number and total number of titles, and skips to the desired title
number.
•
•
Some options cannot be reset, including Parental Controls, Password, and Country Code.
After Restoring Defaults the unit reboots automatically and the Installation menu appears. You must set the
country, language, channel, and clock setting again.
02/17
Cha pter : Shows the current chapter number and total number of chapters, and skips to the
desired chapter number.
001/002
Tim e Ela psed
:
Shows the elapsed playing time, and skips to the desired time.
0:00:26
Audio : Shows the current audio soundtrack language, encoding method, and channel number,
and changes the setting; AC3 5.1 CH English or AC3 2 CH English
Subtitle : Shows the current subtitle language, and changes the setting
Off
Off
Repea t : Shows the current repeat mode, and changes the setting; Chapter, Title, All or Off
A-B Repea t : Shows the current A-B repeat mode, and changes the setting; A-, A-B or Off
Ra ndom Repea t : Shows the current random repeat mode, and changes the setting; On or Off
OSD La ngua ge : Shows the current OSD language, and changes the setting
Off
Off
1
Tra ck : Shows the current track number and total number of tracks, and skips to the desired
track number.
01/16
Audio Effect : Shows the current audio effect, and changes the setting; Stereo or Mix-Mono
Sound Effect : Shows the current sound effect, and changes the setting; Off, Concert, Living
Room, Hall, Bathroom, Cave, Area or Church
Off
2 8
2 9
O n -Scre e n Disp la y O ve rvie w
DVD Pla y b a ck
DVD Pla y b a ck
Disp la y in g TV In fo rm a tio n
Pla y in g a DVD/ VCD
While watching TV, press [DISPLAY] to display/remove the on-screen display.
You would see a screen like the following:
1
2
3
4
Press [EJECT] to open the disc tra y.
PR 1 : - - - -
STEREO
PDC
Loa d your disc in the tra y w ith the pla yba ck side dow n (la bel side up).
Press [EJECT] to close the tra y.
12:30
SP
‘LOAD’ appears on the front panel display, and playback starts automatically. If playback does not start,
press [PLAY (√)]. In some cases, the Disc menu might appear instead.
Pla y in g a DVD+R (+RW, -R, -RW )
When a DVD+RW or unfinalized DVD+R (-R, -RW)is inserted, no title is played automatically but the current TV
channel displays on the screen.
Ch a n g in g th e TV Au d io Ch a n n e l
1
If you w a nt to pla y a title on the DVD+R (+RW, -R, -RW), you m ust press
[MENU] or [PLAY] to displa y the disc m enu of a thum bna il index for ea ch
recorded title on the disc.
You can change the TV audio using the [AUDIO] button.
Press [AUDIO] repea tedly to cha nge the TV a udio, a ccording to the Broa dca st a udio signa l a s show n below .
The index picture screen of the title will be displayed. Also title
information (name of recording, recorded day, time, recording quality)
will be displayed.
•
•
•
STEREO Audio Signa l : Stereo ➝➝Mono ➝➝Stereo
MONO Audio Signa l : Mono
BIL Audio Signa l : BIL1 ➝➝BIL2 ➝➝BIL1
2
Select a title to pla y using [œ √] then press [ENTER] or [PLAY].
If a Disc m e n u is d isp la y e d
The current audio channel is displayed on-screen.
•
A Disc menu may be displayed when you load a DVD. Use the [œ √…†] buttons to select the title/chapter you
•
•
If the sound is poor quality when set to Stereo, you can often improve it by changing to Mono.
When an external input is selected, the audio channel can be switched only to Stereo.
want to view, then press [ENTER] to start playback. Press [TITLE] or [MENU] to return to the Disc menu.
•
•
•
If the Parental Level feature is set and the disc is below the current Parental Level setting, the 4-digit code must
be entered and/or the disc must be authorized; see ‘Set Parental Level‘ on page 25.
The DVD Recorder+VCR will not play discs with Region codes different from the DVD Recorder+VCR. The Region
code for this DVD Recorder+VCR is 2 (two).
Unless stated otherwise, all operations described below use the remote control. Some features may also be
available in the Setup menu.
Ch a n g in g TV Ch a n n e ls
•
•
•
A disc which is recorded by computer at high speeds (greater than or equal to 2x) may not be recognized.
A disc which is recorded with unauthorized movie material may not be played.
A disc which is recorded by other recorder or not recorded correctly may not be recognized or played.
If no disc is playing, you can change TV channels using the [0-9] or [PR+/-] buttons on the remote control or
[PR+/–] buttons on the front panel.
Still Picture a nd Fra m e-by-Fra m e Pla yba ck
1
2
Press [PLAY/PAUSE] during playback. The DVD Recorder+VCR will go into Pause mode.
You can back up or advance the picture frame-by-frame by pressing [FF (√√ )] repeatedly during Pause
mode.
Fa st Forw a rd/ Ba ck w a rd
1
2
Press [REW (œœ )] or [FF (√√ )] during playback. The DVD Recorder+VCR will go into Search mode.
Press [REW] or [FF] to select the desired speed: √√ X2, √√ X4, √√ X8, √√ X16, √√ X32,
, œœ X2, œœ X4, œœ X8, œœ X16, œœ X32 (backward).
√
(forward) or
œ
3 0
3 1
DVD Pla y b a ck
DVD Pla y b a ck
Slow Motion
A-B
You can repeat a scene between two points (A and B):
Press [SLOW+] or [SLOW–] to enter Slow Motion mode. The default speed is 1/2. When you press [SLOW+] or
[SLOW–] repeatedly, the speed will be set to 1/4, 1/8, 1/16, and normal speed.
1
2
3
4
5
Press [PLAY/PAUSE] play to the start of the desired scene.
Press [A-B] to mark the start point.
Cha nging the Audio La ngua ge (DVD)
Use [FF], [NEXT] to search the end point.
Press [A-B] to mark the end point.
Press [AUDIO] and then press
track.
[
AUDIO repeatedly during playback to hear a different audio language or audio
]
Subtitles (DVD)
The marked scenes are repeated continuously until you stop the repeat by pressing [A-B] button again.
Press [SUBTITLE] and then press
languages.
[
SUBTITLE repeatedly during playback to select among all available subtitle
]
Selecting Titles
Ca m era Angle (DVD)
When a disc has more than one title, you can select among all available titles as follows:
If a DVD contains scenes recorded at different camera angles, angle icon displays automatically. You can select
among these angles during playback.
Press [ANGLE] and then press it repeatedly during playback to select the desired angle.
The number of the current angle appears on the TV screen.
1
Press [DISPLAY] and use [œ √] to select the Title icon. Press [ENTER] to display a submenu. Use […†] to
select the desired title number and press [ENTER] to confirm.
Selecting Cha pters
When a title on a disc has more than one chapter, you can select among all available chapters as follows:
The Camera Angle icon is displayed on the TV screen when alternate angles are available.
1
2
Press [PREV (§)] or [NEXT (∞)] briefly during playback to select the next or previous chapter.
Zoom
To skip directly to any chapter during playback, press [DISPLAY]. Use [œ √] to select the Chapter icon, then
press [ENTER] to display a submenu. Use […†] to select the desired chapter number and press [ENTER] to
confirm.
The Zoom function allows you to magnify the video image and scroll around the enlarged image.
1
Press [ZOOM] during Play mode to activate the Zoom function.
Each press of the [ZOOM] button changes the Zoom level as follows: X1 (normal size) ➝ X2 ➝ X3 ➝➝X4 ➝
X1/2 ➝➝X1/3 ➝➝X1/4 ➝ X1 (normal size)
Disc Menus
Many DVDs contain Disc menus that allow you to access special features. To open a Disc menu, press [MENU].
Then use the [0-9] buttons to directly select the desired options, or use the […†] buttons to highlight your
desired selection and press [ENTER].
2
3
Use the [œ √…†] buttons to scroll around the zoomed picture.
To resume normal playback, press [ZOOM] repeatedly until the X1 (normal picture) appears.
1
2
Press [MENU]. The Disc menu is displayed.
To exit the Disc menu, press [STOP].
•
The Zoom function may not work on some DVDs.
Title Menus
Repea t
1
Press [TITLE]. If the current title has a menu, the Title menu will appear on the TV screen. Otherwise, the
Disc menu may appear.
1
2
To repeat the currently playing chapter, press [REPEAT]. REPEAT CHAPTER appears on the TV screen.
2
The Title menu may contain camera angles, spoken languages and subtitle options, as well as the chapters
for the title.
To repeat the currently playing title, press [REPEAT] a second time. REPEAT TITLE appears on the TV
screen.
3
4
To repeat the whole disc, press [REPEAT] a third time. REPEAT DISC appears on the TV screen.
You can play in other modes (including Repeat, A-B, Shuffle, or Scan) by pressing [REPEAT] repeatedly.
Digest
For displaying the edit menu for DVD+RW / +R discs, for setting chapter markers.
1
2
Press [DIGEST]. The Digest menu is displayed.
To exit the Disc menu, press [STOP].
You can repeat a scene that starts when ‘Repeat A-‘ displays on the screen. To mark the end point, press [A-B]. Press
[A-B] again to repeat the scene.
Digest
Title Digest
Chapter Digest
Title Interval
Chapter Interval
Digest
Track Digest
Disc Interval
Track Interval
“Track Interval” won’t be displayed in PBC ON
mode.
…† Select
➝ Exit
…† Select
➝ Exit
• • • DVD • • •
• • • VCD • • •
3 2
3 3
VCR Pla y b a ck
VCR Pla y b a ck
VCR Pla y b a ck
Be fo re Yo u Be g in
Sp e cia l Pla y b a ck Fe a tu re s
N o te s o n sp e cia l p la y b a ck fe a tu re s
Horizontal lines (noise bars) will appear on the TV screen. This is normal.
The audio is automatically muted during special playback modes, so there is no sound during search, slow motion, etc.
During high-speed picture search, a short time is needed to stabilize tape speed when re-entering Play mode. Slight
interference may be observed during this time.
1
2
Press the [VCR] button to set the remote control to operate the VCR deck.
Turn the TV on and select the video input source connected to the DVD Recorder+VCR.
Audio system: Turn the audio system on and select the input source connected to the DVD Recorder+VCR.
Fa st Forw a rd/ Ba ck w a rd
This function lets you visually search forward and backward for a desired scene on your tape.
1
Press [REW] or [FF] during playback.
Pla y in g a VHS Ta p e
Search mode will be activated.
If the DVD Recorder+VCR is left in Search mode for more than 3 minutes, the DVD Recorder+VCR will
automatically resume Play mode to protect the tape and video heads.
1
Insert a prerecorded video ca ssette.
If the DVD Recorder+VCR is powered off, it will power on automatically.
Make sure the TIMER indicator on the front panel display is not lit. If it is, press [POWER] once.
If a tape without a safety tab is inserted, the DVD Recorder+VCR will start playback automatically.
2
To return to normal playback, press [PLAY].
Still Picture
1
Press [PLAY/PAUSE] during playback.
If the DVD Recorder+VCR is powered on by inserting a video cassette, playback will not start automatically.
A still picture appears on the TV screen.
2
3
Press [PLAY].
If a still picture vibrates vertically, stabilize it by using the [TRACKING +/-] buttons on the remote control.
If the DVD Recorder+VCR is left in Still mode for more than 5 minutes, the DVD Recorder+VCR will
automatically enter Stop mode to protect the tape and video heads.
The PLAY icon appears on the TV screen. It is not necessary to select the tape speed (SP, LP) for playback.
It will be automatically selected by the DVD Recorder+VCR.
2
To return to normal playback, press [PLAY].
Press [STOP] to stop pla yba ck .
The STOP icon appears on the TV screen. If the tape reaches the end before [STOP] is pressed, the DVD
Recorder+VCR will automatically stop, rewind, and eject the tape.
Slow Motion
1
2
Press [SLOW+] for Slow Motion playback.
Press [SLOW+] and [SLOW-] repeatedly to adjust the Slow Motion playback speed.
Tra ck in g Co n tro l
Counter Mem ory Function
This is useful if there is a section of tape you want to view immediately after recording or if you want to return
to the same point several times.
Auto Tra ck ing
The automatic tracking function adjusts the picture to remove snow or streaks. It works in the following cases:
1
2
Begin recording or playing a tape.
•
•
•
When a tape is played for the first time.
When the tape speed (SP, LP) changes.
When streaks or snow appear because of scratches on the tape.
At the point you want to locate later, reset the real-time counter to 0:00:00 by pressing [CLEAR]. Continue
to play or record.
Ma nua l Tra ck ing
3
4
Press [STOP] when recording or playback finishes.
If noise appears on the screen during playback, press the [TRACKING +/-] buttons on the remote control until
the noise on the screen is reduced.
You can make the tape automatically stop when the counter returns to about ‘0:00:00‘ by selecting "Go-to-
Zero" function under ‘SETUP’ ➝ ’Preferences’ ➝➝’VCR’. See page 27.
•
•
In case of vertical jitter, adjust these controls very carefully.
Tracking is automatically reset to normal when the tape is ejected or the power cord is unplugged for more
than 3 seconds.
3 4
3 5
O th e r Disc Pla y b a ck
O th e r Disc Pla y b a ck
O th e r Disc Pla y b a ck
Au d io CD/ MP3 PLAYBACK
5
6
7
Press [NEXT] or [PREV] to manually skip to the next or previous image.
Press [ ] (or [ ]) to rotate the image (counter) clockwise.
Press [STOP] to exit the slideshow.
The DVD Recorder+VCR can play audio CDs and MP3 files on CD-ROM, CD-R or CD-RW discs.
√
œ
• • • MP3 • • •
1
2
Insert the CD disc and close the tray. The Audio CD or MP3 CD menu
appears on the TV screen after a few moments to load the disc.
Use […†] to select a track or a file, then press [PLAY] or [ENTER].
During playback, the current track's elapsed playing time will appear on
the menu. Playback will stop at the end of the disc.
•
•
•
When a CD contains both MP3 files and JPEG files, the default Play mode is JPEG image files.
The DVD Recorder+VCR can playback up to 1000 files per disc.
MP3 files encoded below 64kbps are not supported.
On the MP3 CD menu, you can display the folders on the disc.
Use […†œ √] to select the folder icon on the MP3 CD menu then press
[ENTER] or [PLAY].
You can also display just the tracks in the folders.
Use […†œ √] to select a folder then press [ENTER].
3
4
5
While playing an Audio CD, use [FF] or [REW] for 2X, 4X, 8X, 16X, 32X speed playback.
Use [PLAY/PAUSE] to pause playback while the disc is playing.
To stop playback at any time, press [STOP].
Pla y in g MP3 File s Du rin g a Slid e Sh o w
•
Press [REPEAT] to repeat a track (file) and press again to repeat the whole disc.
You can enjoy a slide show while listening to MP3 music files.
1
2
3
4
5
Prepare a CD which includes both MP3 and JPEG files.
Insert the CD and play an MP3 file.
Press [TITLE] while playing the MP3 file to change the Play mode. The music playback will not stop.
Select an image file and press [ENTER] to start the slide show.
The MP3 file you selected continues to play during the JPEG slide show.
JPEG / Ko d a k Pictu re CD PLAYBACK
The DVD Recorder+VCR can display JPEG files on CD-R/RW and Kodak Picture CDs.
1
Insert your CD and close the tray. The JPEG CD or Kodak Picture CD
folder tree appears.
2
If there are folders which contain JPEG files (e.g., pictures on a Kodak
Picture CD), select the desired folder using […†œ √] and press
[ENTER].
3
4
Select the thumbnail you want to display using […†œ √] and press
[ENTER].
The full size image will be displayed and a slide show starts
automatically with a time interval of 10 seconds.
3 6
3 7
O th e r Disc Pla y b a ck
Ba sic Re co rd in g
Ba sic Re co rd in g
DivX m o d e l o n ly
DivX PLAYBACK
The DVD Recorder can play DivX files on CD-R/RW.
Re co rd in g fro m TV
Follow the instructions below to record a TV program.
1
Insert the DivX disc and close the tray. The DivX Menu appears on the
TV screen after a few moments to load the disc.
1
Turn on the DVD Recorder+VCR a nd loa d a recorda ble disc or ta pe.
Make sure your TV input is set to view the DVD Recorder+VCR.
Set the desired Recording m ode by pressing [REC MODE] repea tedly.
2
3
Use […†] to select a file, then press [ENTER].
2
DVD: HQ (High Quality - 1 hr/disc), SP (Standard Play - 2 hrs/disc), EP (Extended Play - 4 hrs/disc), or SEP
(Super Long Play - 6 hrs/disc).
Press [FF] or [REW] during playback. The DVD Recorder will go into
Search mode.
VCR: SP (Standard Play), LP (Long Play - 2 times SP)
Press [FF ]or [REW ]to select the desired speed:
3
4
If your DVD Recorder+VCR does not show a TV progra m , press [INPUT] on the rem ote control. Use [PR+/ –] to
select the TV cha nnel you w ish to record.
√√ X8, √√ X16, √√ X32, √PLAY(forward) or œœ X8, œœ X16,
œœ X32, œ PLAY(backward)
4
5
Use [PLAY/PAUSE] to pause playback while the disc is playing.
Press [ZOOM] during Play mode to activate the Zoom function.
Press [AUDIO] to select the a udio cha nnel to record (Stereo, BIL, or Mono).
The table below shows what audio channel will be recorded with different settings and different types of
broadcasts.
The last column (Monitor Audio) shows what you will hear during recording. For example, if the TV
broadcast is in Stereo, then setting the DVD Recorder+VCR to Stereo will record the broadcast in Stereo,
and the Monitor Audio will also be in Stereo.
Each press of the [ZOOM] button changes the Zoom level as follow :X2 ➝ X4 ➝ 1 (normal size)
6
To stop playback at any time, press [STOP].
SUBTITLES
Bro a d ca st Au d io
Mo n ito r
Au d io
MONO
STEREO
MONO
BIL I
When the subtitles are not displayed provided although it has a file of
subtitles:
TV Bro a d ca st
Se le cte d Au d io
L Ch
MONO
L
R Ch
MONO
R
MONO
MONO
STEREO
MONO
BIL I
1
2
3
4
Move to the Menu of DivX by pressing the [STOP] button.
Use […†] to select a file of subtitles you want by using it.
Select the file of subtitles at that time by pressing the [ENTER] button.
STEREO
MONO
BIL I
MONO
BIL I
BIL
BIL II
BIL II
BIL II
BIL II
After moving the file of DivX you want to play, play it by pressing the
[ENTER] button.
5
6
Press [REC (➝)] once.
Recording will start. The REC indicator lights on the front panel display.
Recording continues until you press [STOP] or the disc is full.
To record for a fixed length of time, see One Touch Record on the next page.
•
DivX® is a high-quality video compression format for creating, editing, and distributing multimedia content. More
than just a video technology, DivX is a global phenomenon that has become the new standard for digital video.
Dubbed the “MP3 of video” for its remarkable compression and widespread popularity, DivX video enables
anyone, anywhere to create and enjoy DVD-quality digital video.
Press [STOP (➝)] to stop recording.
•
•
•
The maximum number of DVD titles per disc is 49. If the DVD Recorder+VCR is powered off during DVD recording,
the recording will not be saved.
If a DVD+RW or unfinalized DVD+R disc is inserted in the tray, no title is played automatically after loading is
finished.
If you are recording to a blank DVD+R (+RW) disc, it may take up to 7 minutes (it depends on disc) for post
processing after recording.
•
•
•
•
•
•
•
Playable MPEG 4 SP and ASP is DivX5.1, DivX5.05, DivX5.02, DivX4.1.2, DivX3.11, and Dr. DivX1.0.2.
ASP does not support GMC & Qpel(Quarter Pixel).
Playable biterates is to max. 4MBPS.
Playable frame number of screens per a second is 30, 25, 24, 12, and 8.
Playable resolution is from Min. 200X100 to max. 720X576.
Playable audio stream formats are MPEG I Layer III, MPEG II, PCM and AC-3.
It may not be played according to a type of DivX files, a recording method, or a disc state. (The device was
authenticated for DivX files from the DivX Networks, Inc. and it is available for playing a normal DivX but may be
unavailable for playing the DivX files that have been manufactured with an illegal or abnormal Codec.)
DivX,DivX certified and associated logos are trademarks of DivXNetworks, Inc. and are used under license.
O n e To u ch Re co rd (O TR)
One Touch Recording allows you add recording time in fixed increments at the touch of a button.
•
1
2
Follow steps 1 -4 under Recording from TV.
Press [REC (➝)] repea tedly to set the length of the recording.
Recording starts after the first press. Each subsequent press increases the recording time by 15 minutes
(DVD) within the available space or 30 minutes (VCR, to a maximum of 10 hours). The recording time is
displayed on the front panel display.
3 8
3 9
Ba sic Re co rd in g
Ba sic Re co rd in g
Ch e ck in g th e Re co rd in g Tim e
Co p y Ed it (DVD ➝VCR)
During one touch copy you can search or change REC SPEED and resume copy.
Total time and recorded time are displayed on the TV screen after pressing [DISPLAY]. Recorded time is
displayed on the front panel display.
1
2
3
4
During One Touch Copy, press [PLAY/ PAUSE] to enter COPY EDIT m ode.
Sea rch w ith [FF/ REW] or [NEXT/ PREV] button.
To Pa u se th e Re co rd in g
Press [VCR œœ DVD] a nd you ca n cha nge REC SPEED.
Press [VCR œœ DVD] a ga in to resum e copy.
1
2
Press [PLAY/PAUSE] to pause the disc or tape during recording.
When you want to continue recording, press [PLAY/PAUSE] or [REC (➝)] in DVD mode and press [REC (➝)]
in VCR mode.
O n e To u ch Co p y - VHS to DVD
N o te
You can copy the contents of a VHS tape to a DVD±R or DVD±RW. This allows you to archive your old VHS
tapes to DVD.
•
•
To quit One Touch Recording, press and hold [STOP] for 3 seconds.
The DVD Recorder+VCR will automatically power off when One Touch Recording ends.
If the VHS videotape you are attempting to copy is copy-protected, you will not be able to copy the tape. It is not
permitted to copy Macrovision encoded tapes.
Tip (VCR m o d e o n ly )
•
Always use [PLAY/PAUSE] for best results when making changes during recording.
1
2
Insert a VHS Ta pe.
For example: To change channels during recording, first press [PLAY/PAUSE] to put the unit in Pause mode. Then
select the desired channel on the DVD Recorder+VCR, and press [REC (➝)] again to resume recording.
Insert the VHS videotape you wish to copy into the VCR deck.
Insert a DVD±R or DVD±RW disc.
•
•
You cannot record on the VCR deck and DVD deck at the same time.
While the VCR is recording, DVD playback is possible. However, while the DVD is recording, all VCR functions are
disabled.
Insert a blank DVD±R or DVD±RW disc in the DVD deck and close the disc tray.
When using a DVD+RW disc, you must initialize before copying; see page 47.
O n e To u ch Co p y - DVD to VHS
3
Find the pla ce on the VHS ta pe from w hich you w a nt to sta rt recording using the [PLAY/ PAUSE], [FF] a nd [REW]
functions. And press [STOP].
Copy to Tape
Choose quality and
press COPY key:
LP
SP
If the DVD you are attempting to copy is copy-protected, you will not be able to copy
the disc. It is not permitted to copy Macrovision encoded DVDs.
4
5
Press [VCR √√ DVD] on the front pa nel.
Copy to Disc
Choose quality and
press COPY key:
1
Insert a Disc.
Press [ENTER] to select the desired Record Mode in ‘Copy to Disc’ m enu:
HQ
SP
Insert the disc you wish to copy in the DVD deck and close the disc tray.
Insert a VHS Ta pe.
• HQ (High Quality - 1 hr/disc)
• SP (Standard Play - 2 hrs/disc)
2
3
EP
➝ Stop
SEP
• EP (Extended Play - 4 hrs/disc)
Insert a blank VHS videotape into the VCR deck.
➝ Stop
• SEP (Very Low Quality - 8 hrs/disc)
Find the pla ce on the DVD disc ta pe from w hich you w a nt to sta rt recording using the [PLAY/ PAUSE], [FF] a nd
[REW] functions. And press [STOP].
6
7
Press [VCR √√ DVD] a ga in to sta rt copying.
4
5
Press [VCR œœ DVD] on the front pa nel.
Stop the Copy Process
To stop copying at any time, press [STOP].
Press [ENTER] to select the desired Record Mode in ‘Copy to Ta pe’ m enu:
Copying will stop automatically when the VHS tape ends.
• SP (Standard Play)
• LP (Long Play, 2 times SP).
6
7
Press [VCR œœ DVD] a ga in to sta rt copying.
Co p y Ed it (VCR ➝➝DVD)
During one touch copy you can search and resume copy.
Stop the Copy Process
To stop copying at any time, press [STOP]. You must stop the Copy process manually when the DVD movie
ends, or the unit may replay and record over and over again.
1
2
3
4
Press [PLAY/ PAUSE] to enter COPY EDIT m ode.
Press [PLAY/ PAUSE] a ga in to pla yba ck .
Sea rch w ith [FF/ REW] button.
If y o u w a n t to sta rt co p y a n y p o in t o f d isc
1. Find the place on the DVD (or Disc) from which you want to start recording using the [PLAY/PAUSE], [REW] and
[FF] functions.
2. Press [COPY] while DVD is in pause mode or in resume stop (» STOP) mode.
3. Follow the same procedure 5-7.
Press [VCR √√ DVD] to resum e copy.
4 0
4 1
Tim e r Re co rd in g
Tim e r Re co rd in g
Tim e r Re co rd in g
Tim e r Re co rd in g u sin g Ma n u a l Se t Re co rd Scre e n
•
•
The Timer indicator lights on the front panel display when the DVD Recorder+VCR is ready for the Timer
Recording.
The Timer Recording function allows you to record up to 8 programs within a period of one month.
The DVD Recorder+VCR will record the audio according to the current TV tuner setting (Stereo, Mono or SAP). Use
the [AUDIO] button to set the audio before switching the DVD Recorder+VCR to Standby mode.
The DVD Recorder+VCR will automatically power off when the Timer Recording ends.
There is a short delay when a timer recording finishes to confirm the recorded program. If two timer recordings
are set to record sequentially (one right after the other), the very beginning of the later program may not be
recorded.
1
2
Insert recorda ble m edia such a s DVD±R ,DVD±RW, recorda ble VHS ta pe.
Press [TIMER].
•
•
DVD Recorder
Init Setup ➝
or Press [SETUP] a nd select ‘Tim er REC’. Then press [ENTER].
The ‘Timer Recording’ menu appears.
Timer REC
œ √ Select
If you did not set the clock on the DVD Recorder+VCR, you must do so
before programming a timer recording.
Init Setup
Disc Oper
Disc Edit
Timer REC
Timer Recording
Tim e r Re co rd in g u sin g Sh o w Vie w (Vid e o Plu s) sy ste m
3
4
Select ‘Ma nua l’ w ith […/ †] a nd confirm w ith [ENTER].
Manual
Thanks to this programming system, you no longer need to tediously enter the date, programme number, start
and end time. All the information needed by the DVD Recorder+VCR for programming is contained in the
ShowView (VideoPlus) programming number. This ShowView (VideoPlus) number is found in most TV listings.
ShowView (VideoPlus)
…†
Move
Confirm
ENTER
Use […/ † ] to m ove to a tim er recording slot, a nd press [ ENTER] to m odify it.
Timer Recording
PR No Date Start Stop
1
2
Insert recorda ble m edia such a s DVD±R ,DVD±RW.
Press [TIMER].
01/01 00:13:23
Media Repeat Mode
New Input
Timer Recording
Manual
or Press [SETUP] a nd select ‘Tim er REC’. Then press [ENTER].
ShowView (VideoPlus)
The ‘Timer Recording’ menu appears.
…†
Move
Confirm
ENTER
➝
§
ENTER
TIMER
Exit
Delete
Edit
Next Page
Prev Page
∞
3
Select ‘Show View (VideoPlus)’ w ith […/ †] a nd confirm w ith [ENTER].
The ‘ShowView (VideoPlus)’ menu appears.
Enter the entire ‘ShowView (VideoPlus)’ number. This number is up to 9
digits long and can be found next to the start time of the TV programme in
your TV listings magazine.
e.g.: 5-234-89 or 5 234 89
Enter 523489 for the ‘ShowView (VideoPlus)’ number.
Timer Recording
01/01 00:13:23
Code
Media
Mode
1111
DVD
SP
Timer Recording
01/01 00:13:23
5
Enter the necessa ry inform a tion for your Tim er Recording(s).
PR No Date Start Stop
PR01 16/1 11:02 12:00
Media Repeat Mode
DVD
Once
SP
• PR No. – Choose the desired channel, or one of the external inputs from
which to record.
New Input
Repeat
Once
• Date – Choose a date up to 1 month in advance, or select a daily or weekly
program.
0-9 Input Digits ENTER Confirm and Exit
SETUP Exit timer rec
➝
§
ENTER
TIMER
Exit
Delete
Edit
Next Page
• Start – Set the recording start time.
• Stop – Set the recording end time.
• Repeat – Choose frequency of the recording. Once, Daily, Weekly,
Weekday.
• Media - Choose desired media (DVD or VHS) using […†].
• Title - Enter into title edit mode pressing [➝].
• Mode – Choose a Record mode.
4
5
Press [ENTER] to confirm .
Prev Page
∞
The decoded information appears after confirmation. You can change the
information by selecting the appropriate input field using […†]. If
required, change the information using […†].
If all the information is correct, press the [ENTER] button. The programming
information is stored in a TIMER block.
Timer Recording
01/01 00:13:23
Repeat
PR No
…
Date
Start
Stop
Timer Recording
01/01 00:13:23
Repeat
PR
1
†
16
/
1
11 : 00
12 : 00
Once
PR No
…
Date
Start
Stop
Sun
PR
1
†
16
/
1
11 : 00
12 : 00
Once
Media
DVD
Title
Mode
SP
Sun
Media
DVD
Title
Mode
SP
TITLE PR 4
6
7
Press [SETUP] to ex it the Tim er Record List.
TITLE PR 4
➝
0-9 Input Digits
Delete
DVD: HQ, SP, EP or SEP
VCR: SP, LP
TIMER Exit timer rec
➝
0-9 Input Digits
TIMER Exit timer rec
Delete
Tim er indica tor w ill light or be blink ing. Pow er Off the DVD Recorder+VCR to
sta rt the Tim er Recording.
[œ √] – Moves the cursor left/right.
Timer Recording
01/01 00:13:23
PR No Date Start Stop
PR01 16/1 11:02 12:00
Media Repeat Mode
[…†] – Changes the setting at the current cursor position.
Press [SETUP] to exit the Timer Record menu.
Press [ENTER] to save the program after filling in all the program information.
•
•
ShowView (VideoPlus) is not available in some countries.
ShowView (VideoPlus) is a trademark applied for by Gemstar
Development Corp. The ShowView (VideoPlus) system is manufactured
under license from Gemstar Development Corporation.
DVD
Once
SP
New Input
➝
§
ENTER
TIMER
Exit
Delete
Edit
Next Page
7
Tim er indica tor w ill light or blink ing. Pow er Off the DVD Recorder+VCR to sta rt the Tim er Recording.
Prev Page
∞
4 2
4 3
Tim e r Re co rd in g
Re co rd in g fro m a n Ex te rn a l In p u t
Re co rd in g fro m a n Ex te rn a l In p u t
Ca n ce lin g a Tim e r Re co rd in g
Re co rd in g fro m Ex te rn a l Co m p o n e n ts
You can clear a Timer Recording any time before the recording actually starts.
You can record from an external component, such as a camcorder or VCR, connected to any of the DVD
Recorder+VCR’s external inputs.
•
Use […†] to select the program you want to erase on the Timer Recorder List. Press [➝STOP] to delete the
program.
1
Ma k e sure the com ponent you w a nt to record from is connected properly to the DVD Recorder+VCR; see pa ges
1 1 a nd 1 4 .
2
3
4
Use [ … †] or [INPUT] to select the ex terna l input to record from .
Loa d a recorda ble disc or ta pe.
Sto p p in g a Tim e r Re co rd in g in Pro g re ss
After a Timer Recording has started, you can still cancel the program by pressing and holding [➝STOP] for 3
seconds.
Set the desired Recording m ode by pressing [REC MODE] repea tedly.
DVD: HQ (High Quality - 1 hr/disc), SP (Standard Play - 2 hrs/disc), EP (Extended Play - 4 hrs/disc), SEP (Very
Low Quality - 8 hrs/disc)
VCR: SP (Standard Play), LP (Long Play - 2 times SP)
Tim e r Re co rd in g Tro u b le sh o o tin g
5
6
Press [REC (➝)] once.
Even if a Tim er Recording is set, the DVD Recorder+VCR w ill not record if:
Recording will start. The REC indicator lights on the front panel display.
Recording continues until you press [STOP] or the disc is full.
To record for a fixed length of time, see ‘One Touch Record‘ on page 39.
•
•
•
•
No disc is loaded.
A non-recordable disc is loaded.
Disc is protected in the ‘Disc Operation’ menu; see page 47.
There are already 49 titles recorded on the disc.
Press [STOP (➝)] to stop recording.
N o te
You ca nnot enter a Tim er Recording if:
If your source is copy-protected, you will not be able to record it using the DVD Recorder+VCR. See ‘Copyright Notice‘
on page 4 for more details.
•
•
•
A recording is already under way.
The start time has already passed.
Eight Timer Recordings have already been set.
DV m o d e l o n ly
Re co rd in g fro m a Dig ita l Ca m co rd e r
If tw o or m ore Tim er Recordings overla p:
Timer Recording
Recording time is overlapped with
existing entry.Replace it?
You can record from a digital camcorder connected to the DV IN jack on the front panel of the DVD
Recorder+VCR.
You can use the DVD Recorder+VCR remote to control both the camcorder and the DVD Recorder+VCR. Before
recording, make sure the digital camcorder is properly connected to the front panel DV IN jack; see page 14.
•
•
•
You should set only one Timer Recording.
You can choose replace old Timer Recording or not.
Only one Timer recording will work.
OK
Cancel
Confirm a tion is not possible w hen:
The source signal must be DVC SD format.
•
•
Disc is protected in the ‘Disc Operation’ menu; see page 47.
There are already 49 titles recorded on the disc.
Some camcorders cannot be controlled using the DVD Recorder+VCR remote.
If you connect a second DVD recorder using a DV cable, you cannot control the second recorder from this one.
You cannot control the DVD Recorder+VCR remotely from a component connected to the DV IN jack.
You cannot record date and time information from a DV cassette.
If the disc is damaged, the recording may not complete successfully, even if the Check field shows ‘Rec. OK‘.
1
2
Ma k e sure your digita l ca m corder is connected to the front pa nel DV IN ja ck ; see pa ge 1 4 .
Press [INPUT] repea tedly to select the DV input.
DV appears on the front panel display and the TV screen.
Find the pla ce on the ca m corder ta pe from w hich you w a nt to sta rt recording.
3
For best results, pause playback at the point you want to start recording. Depending on your camcorder, you
can use the DVD Recorder+VCR remote to control the camcorder using the STOP, PLAY, and PAUSE
functions.
4
Press [REC] once to sta rt recording.
Recording is automatically stopped if the DVD Recorder+VCR detects no signal. You can pause or stop the
recording by pressing [PLAY/PAUSE] or [STOP]. You cannot control the camcorder from the remote control
during recording.
4 4
4 5
Re co rd in g fro m a n Ex te rn a l In p u t
Disc O p e ra tio n
Disc O p e ra tio n
DV m o d e l o n ly
W h a t is DV?
Disc In itia lize
Using DV, also known as i.LINK, you can connect a DV-equipped camcorder to the DVD Recorder+VCR using a
single DV cable for input and output of audio, video, data and control signals.
The i.LINK interface is also known as IEEE 1394-1995.
“i.LINK” and the “i.LINK” logo are trademarks.
•
•
•
If you load a blank DVD±R (±RW) disc, it will be initialized (formatted to enable recording).
Do not start recording until disc initialization is complete.
If you load a DVD±RW that has already been used you can record a program immediately.
• The DVD Recorder+VCR is only compatible with DV-format (DVC-SD) camcorders. Digital satellite tuners
and Digital VHS video recorders are not compatible.
• You cannot connect more than one DV camcorder at a time to the DVD Recorder+VCR.
• You cannot control the DVD Recorder+VCR from external equipment connected via the DV IN jack (including
two DVD Recorders).
Disc O p e ra tio n in DVD±RW d isc
• It may not always be possible to control the connected camcorder via the DV IN jack.
• Audio input to the DV IN jack should be 32 or 48kHz (not 44.1kHz).
• Picture disturbance on the recording may occur if the source component pauses playback or plays an
unrecorded section of tape, or if the power fails in the source component, or if the DV cable becomes
disconnected.
For recordable DVD media, such as DVD±R and DVD±RW discs, you can manage the disc using the Disc Menu.
The DVD±RW Disc Menu allows you to erase, lock, or unlock your disc. You can also make it compatible with
most other DVD players.
At first, go to Disc Opera tion m ode.
1
2
Press [SETUP]. The Setup menu appears.
DVD Recorder
Init Setup ➝
While ‘Disc Oper‘ is selected, press [ENTER] to go to the Disc
Operation page.
Disc Operation
œ √ Select
Init Setup
Disc Oper
Disc Edit
Timer REC
Era se the disc (DVD±RW)
3
4
5
Use […/†] to select the ‘Erase’ menu.
If you want to erase the whole disc, press [ENTER].
To confirm, select ‘OK‘. To cancel, select ‘Cancel‘.
Erase
Finalize
Protect
Make Comp
Adapt
Disc Info
Disc Operation
…†
Select
ENTER
OK
DISC
If you select ‘OK‘ and press [ENTER], all the contents of the disc will
be lost.
Exit
_
Exit
Erase
Erase this disc?
Cancel
OK
Protect Disc (DVD±R, DVD±RW)
If you want to protect a disc from accidental recording, editing, or
erasing, you can lock the disc. Later, if you change your mind, you can
unprotect the disc.
Erase
Finalize
Protect
Make Comp
Adapt
Disc Info
Disc Operation
…†
Select
ENTER
OK
3
4
5
Use […/†] to select ‘Protect’ menu.
DISC
Exit
_
Exit
If you want to protect the whole disc, press [ENTER].
To confirm, select ‘OK‘. To cancel, select ‘Cancel‘.
Protect
Protect this disc?
OK
Cancel
If you select ‘OK‘ and press [ENTER], all the contents of the disc will be protected.
4 6
4 7
Disc O p e ra tio n
Disc O p e ra tio n
Disc O p e ra tio n in DVD±R, DVD-RW d isc
Ma k e Com pa tible (DVD±RW)
'Make Compatible' for a DVD±RW will automatically create a menu
screen for navigating the disc. This menu screen is accessible by
pressing [MENU] or [TITLE].
For recordable DVD media, such as DVD±R and DVD±RW discs, you can manage the disc using the Disc Menu.
The DVD±R, DVD-RW Disc Menu allows you to rename your disc or finalize it so it will be compatible with most
other DVD players.
Erase
Finalize
Protect
Make Comp
Adapt
Disc Info
Disc Operation
…†
Select
At first, go to Disc Opera tion m ode.
3
4
5
Press […/†] to select ‘Make Compatible‘.
ENTER
OK
1
2
Press [SETUP]. The Setup menu appears.
DISC
Exit
_
Exit
If you want to make the disc compatible, press [ENTER].
To confirm, select ‘OK‘. To cancel, select ‘Cancel‘.
While ‘Disc Oper‘ is selected, press [ENTER] to go to the Disc Operation page.
Make Compatible
Make Compatible?
OK Cancel
If you select ‘OK‘ and press [ENTER], your disc will be made compatible.
Fina lize (DVD±R, DVD-RW)
Finalizing a DVD±R, DVD-RW ‘locks’ its recordings in place so the disc
can be played on most standard DVD players or computers equipped
with DVD-ROM drives.
•
•
‘Make Compatible’ can take up to 3-4 minutes depending on the type of disc, how much is recorded on the disc,
and the number of titles on the disc.
If you do not make your DVD±RW disc compatible, your edits will not be recognized by other DVD players.
Erase
Finalize
Protect
Disc Operation
…†
Select
Make Comp
Adapt
Disc Info
3
4
5
Use […/†] to select ‘Finalize’ menu.
ENTER
OK
DISC
Exit
_
Exit
If you want to finalize the whole disc, press [ENTER].
To confirm, select ‘OK‘. To cancel, select ‘Cancel‘.
If you select ‘OK‘ and press [ENTER], the disc will be finalized.
Ada pt
Finalize
DVD recordings from different manufacturers have their unique Disc
menu structure. When a recordable DVD disc is recorded in another
brand DVD recorder, the Disc has a different Disc menu structure from
DAEWOO DVD recorders. So, the Disc menu should be changed to
DAEWOO Disc menu to be compatible with DAEWOO DVD Recordings.
It is called Adapt function. After Adapt function is completed, recorded
title contents are exactly the same, but only Disc menu is changed.
Finalize this disc?
OK
Cancel
Erase
Finalize
Protect
Make Comp
Adapt
Disc Info
Disc Operation
…†
Select
•
•
Once you have finalized a DVD±R, DVD-RW disc, you cannot edit or record anything else on that disc.
It may take over 7 minutes for finalizing the edited disk, you'd better wait till the set finishes the finalising
operation.
‘Finalize’ can take up to 3-4 minutes depending on the type of disc, how much is recorded on the disc, and the
number of titles on the disc.
ENTER
OK
DISC
Exit
_
Exit
•
Adapt?
Adapt this disc?
3
4
5
Use […/†] to select ‘Adapt’ menu.
OK
Cancel
If you want to adapt the whole disc, press [ENTER].
To confirm, select ‘OK‘. To cancel, select ‘Cancel‘.
If you select ‘OK‘ and press [ENTER], the disc will be adapted.
Inform a tion
3
4
Press […/†] to select ‘Disc Info’.
The Disc Info Menu shows you disc information, such as disc type,
number of recordings, total titles, free space, etc.
Erase
Finalize
Protect
Disc Operation
…†
Select
Make Comp
Adapt
Disc Info
ENTER
OK
DISC
Exit
_
Exit
Remainder
HQ : 60 (M)
Label Empty
DVD+RW
Title NO.
3
Media
SP : 116 (M)
EP : 233 (M)
SEP : 438 (M)
Status Recordable (NTSC)
Close
154/4414MB
4 8
4 9
Disc Ed it
Disc Ed it
Disc Ed it
Title Me n u
Divide (DVD±RW)
This feature allows you to divide a title into two titles.
You can manage the titles on your DVD±R/±RW discs using the Title
menu.
Edit
DVD Recorder
Init Setup ➝
TITLE CH 10
TITLE CH 10
10:20 am 12/21/04
10:34 am 12/21/04
SEP
HQ
Label
Erase
Divide
2
3
4
5
Select the title to be divided using [ENTER].
Select ‘Divide’ using [… †] .
At first, go to Disc Edit m ode.
Disc Edit
œ √ Select
Protect
Chap Edit
Index Pic
1
2
Press [SETUP]. The Setup menu appears.
Init Setup
Disc Oper
Disc Edit
Timer REC
Press [ENTER] to divide the title.
While ‘Disc Edit‘ is selected, press [ENTER] to go to the Disc Edit
page.
_
Exit
…
†
œ
√
Select
SETUP Exit
Select 'OK' and press [ENTER] to confirm.
ENTER
Confirm
§
Prev Page
∞
Next Page
Edit
TITLE CH 10
TITLE CH 10
10:20 am 12/21/04
10:34 am 12/21/04
SEP
HQ
Label
Erase
Divide
Protect
Chap Edit
Index Pic
6
7
Press [ENTER] when the preferred picture is on your TV screen.
It may take a few minutes to divide the title.
Edit
_
Exit
…
†
œ
√
Select
SETUP Exit
ENTER
Confirm
§
Prev Page
∞
Next Page
La bel a Title
➝
ENTER
Stop
Confirm
To change the name of a title:
Edit
Divide
2
3
4
5
Select the title to be labelled using [ENTER].
Select ‘Label’ using [… †] .
TITLE CH 10
TITLE CH 10
10:20 am 12/21/04
10:34 am 12/21/04
SEP
HQ
Label
Erase
Divide
Protect
Chap Edit
Index Pic
Please wait....
Protect
Press [ENTER] to change the title name.
_
Exit
If you want to protect a title from accidental recording, editing, or
erasing, you can lock the title. Later, if you change your mind, you can
unprotect the title.
Edit
…
†
The Keyboard Menu will be displayed. Use [œ √…†] to select a
character or function and press [ENTER].
œ
√
Select
SETUP Exit
ENTER
Confirm
§
Prev Page
∞
Next Page
TITLE CH 10
TITLE CH 10
10:20 am 12/21/04
10:34 am 12/21/04
SEP
HQ
Label
Erase
Divide
Protect
Chap Edit
Index Pic
Label Title
6
After the new title name is complete, select ‘OK’ and press
[ENTER].
2
3
4
5
Select the title to be protected using [ENTER].
Select ‘Protect’ using [… †] .
TITLE CH 10
a
j
b
k
c
l
d
e
f
g
p
u
h
q
v
i
r
_
Exit
m
n
o
t
Clear
OK
Cancel
…
†
œ
√
Select
SETUP Exit
Space
z
s
w
Press [ENTER] to protect the title.
ENTER
Confirm
§
Prev Page
∞
Next Page
x
y
_
-
Backspace
‘A’
‘a’
Symbol
Protect
Select 'OK' and press [ENTER] to confirm.
…
†
Protect the title(s)?
OK Cancel
0-9
Input digits
Prev Page
Backspace
Next Page
œ
√
Select
Delete
œœ
➝
§
∞
Era se a Title
Protect
6
The Protect Title progress bar will be displayed. This may takes several seconds.
The Protect icon ‘ ’ will appear in front of Title name.
Please wait....
2
3
4
5
6
Select the title to be erased using [ENTER].
Edit
TITLE CH 10
TITLE CH 10
10:20 am 12/21/04
10:34 am 12/21/04
SEP
HQ
Label
Erase
Divide
Protect
Chap Edit
Index Pic
Then select ‘Erase‘ using [… †].
Press [ENTER] to erase the title.
Edit
TITLE CH 10
TITLE CH 10
10:20 am 12/21/04
10:34 am 12/21/04
SEP
HQ
Label
Erase
Divide
Protect
Chap Edit
Index Pic
Select 'OK' and press [ENTER] to confirm.
_
Exit
…
†
œ
√
Select
SETUP Exit
The Erase Title progress bar will be displayed. This may take
several seconds.
ENTER
Confirm
§
Prev Page
∞
Next Page
_
Exit
…
†
œ
√
Select
SETUP Exit
Erase
ENTER
Confirm
§
Prev Page
∞
Next Page
Erase the title(s)?
OK Cancel
7
After erasing is complete, the erased title remains as an empty title.
You can erase titles on DVD±RW discs only.
5 0
5 1
Disc Ed it
Tro u b le sh o o tin g
Tro u b le sh o o tin g
Check the following guide for the possible cause of a problem before contacting customer support.
Edit Cha pters
Sym ptom
Ca use
Solution
Edit
2
3
4
5
Select the title to be edited using [ENTER].
No power.
The power cord is disconnected.
Plug the power cord into the wall outlet
securely.
Select the appropriate video input on the
TV so the picture from the DVD
Recorder+VCR appears on the TV screen.
Connect the video cable securely.
TITLE CH 10
TITLE CH 10
10:20 am 12/21/04
10:34 am 12/21/04
SEP
HQ
Label
Erase
Divide
Protect
Chap Edit
Index Pic
Select ‘Chap Edit’ using [… †] .
No picture.
No sound.
The TV is not set to receive DVD
Recorder+VCR signal output.
Press [ENTER] to edit the chapters.
Select 'OK' and press [ENTER] to confirm.
_
Exit
…
†
œ
√
Select
SETUP Exit
ENTER
The video cable is not connected
securely.
Confirm
§
Prev Page
∞
∞
∞
Next Page
6
7
The Chapter Edit Menu will be displayed. Use [œ √…†] to select
one of the various chapter marker functions (Add, Delete, or Hide).
Chap Edit
The TV power is turned off.
The equipment connected with the
audio cable is not set to receive
DVD Recorder+VCR signal output.
The audio cables are not connected
securely.
The power on the equipment
connected with the audio cable is
turned off.
The audio cables are damaged.
The disc is dirty.
Tape heads are dirty.
Tape is a rental or was recorded on
another VCR.
No disc is inserted.
Turn on the TV.
Title
Play
Add Mark
Del Makr
Hide CH
Select the correct input mode on the
audio receiver so you can listen to the
sound from the DVD Recorder+VCR.
Connect the audio cables securely.
Press [ENTER] to confirm.
1
Add/ Delete a Ma rk er
You can add a chapter marker anywhere in a title during playback.
Once the chapter is marked, you can use the chapter search feature as
described above.
You can add/delete chapter markers or delete all chapter markers in a
title.
_
Exit
…
†
œ
√
Select
SETUP Exit
ENTER
Confirm
§
Prev Page
Next Page
Turn on the equipment connected with
the audio cable.
Chap Edit
Title
Play
Add Mark
Del Mark
Hide CH
Replace with new ones.
Clean the disc.
Clean the video heads.
Hide Cha pters
1
Playback picture is poor.
This feature allows you to hide or unhide a chapter. After hiding a
chapter, the chapter is not deleted but only hidden. If a chapter is
hidden then it shows ‘Unhide Chapter‘ and vice versa.
_
Exit
…
†
Use [Tracking +/–] for manual tracking
adjustment while a tape is playing.
Insert a disc or tape. (Check that the disc
indicator on the front panel display is lit.)
Insert a playable disc. (Check the disc
type, colour system, and regional code.)
Place the disc with the playback side down.
Place the disc on the disc tray correctly
inside the guide.
Clean the disc.
Cancel the Parental Control function or
change the rating level.
You cannot connect via the DVD
Recorder+VCR. Connect the component
directly to your TV.
œ
√
Select
SETUP Exit
Prev Page
ENTER
Confirm
§
Next Page
DVD Recorder+VCR does
not start playback.
Cha nge Index Picture
Each title displayed in the Playlist menu is represented by a thumbnail
picture taken from the start of that title or chapter. If you prefer, you
can select a different still picture from within the title.
An unplayable disc is inserted.
Edit
TITLE CH 10
TITLE CH 10
10:20 am 12/21/04
10:34 am 12/21/04
SEP
HQ
Label
Erase
Divide
Protect
Chap Edit
Index Pic
The disc is placed upside down.
The disc is not placed within the
guide.
The disc is dirty.
The Parental Control level is set.
2
3
4
5
Select the title to be edited using [ENTER].
Select ‘Index Pic’ using [… †] .
_
Exit
…
†
œ
√
Select
SETUP Exit
Press [ENTER] to change the index picture.
Press [ENTER] when the preferred picture is on your TV screen.
ENTER
Confirm
§
Prev Page
∞
Next Page
Edit
Picture from external input The video signal from the external
is distorted. component is copy-protected.
Some channels are skipped The skipped channels were deleted
Use the ‘Auto Scan’ menu to restore
channels. See ‘Auto Scan‘ on page 19.
Tighten connections or replace cable.
Try all ‘Tuning Band‘ options; see page
over when using [PR+/–].
Picture or sound of
with the ‘Adjust Channels’ menu.
Antenna or cables are loose.
➝
ENTER
Stop
Confirm
broadcasting channel is
weak or missing.
Wrong Tuning Band is selected in
the DVD Recorder+VCR Setup menu. 17 for details.
Camcorder image not shown. Camcorder is off.
Camcorder image via A/V DVD Recorder+VCR’s source is not
input to DVD Recorder+VCR set to AV1, AV2 or AVF.
is not shown on TV screen.
Turn camcorder on and operate properly.
Use [INPUT] to select AV input channel
(AV1, AV2 or AVF).
5 2
5 3
Tro u b le sh o o tin g
Tro u b le sh o o tin g
Mo istu re Co n d e n sa tio n
Sym ptom
Ca use
Solution
Moisture condensa tion ca n occur:
In loca tions w here m oisture condensa tion m a y occur:
Can’t play disc recorded
The disc was not finalized (or not
Finalise the disc; see page 49.
on this DVD Recorder+VCR made compatible if using a
When the DVD Recorder+VCR is moved from a cold
place to a warm place.
Keep the DVD Recorder+VCR plugged into an AC
power outlet with the power on. This will help
prevent condensation.
on another DVD player.
DVD+RW).
Some players will not play even a
finalized disc.
Discs recorded with copy-once
material cannot be played on other
players.
No solution.
No solution.
Under extremely humid conditions.
When condensation has occurred, wait a few hours
for the DVD Recorder+VCR to dry before using it.
Cannot record or did not
record successfully.
The remaining blank space on the
disc is insufficient.
Use another disc.
The source you are trying to record
is copy-protected.
You cannot record the source.
When setting the recording
channel, the channel is tuned on
your TV’s tuner.
Select the channel on the DVD
Recorder+VCR’s built-in TV tuner.
Timer Recording not
possible.
Clock in DVD Recorder+VCR is not
set to correct time.
Set clock to correct time. See ‘Set Clock‘
on page 19.
Timer has been programmed
incorrectly.
Reprogram Timer. See ‘Timer Recording‘
on page 42~44.
TIMER indicator light does not
appear after programming timer.
Reprogram Timer.
Stereo Audio Record and/or TV is not Stereo-compatible.
No solution.
No solution.
Playback not present.
Broadcast program is not in stereo
format.
DVD Recorder+VCR A/V Out jacks
are not connected to TV A/V In
jacks.
Make A/V connections. Stereo is
available only via A/V output from DVD
Recorder+VCR.
DVD Recorder+VCR Audio/Video
Out is not selected for viewing at
the TV.
Select AUX or A/V source as TV input.
Set TV audio channel mode to Stereo.
DVD Recorder+VCR’s TV audio
channel is set to BIL or MONO.
The remote control is not pointed at
the remote sensor of the DVD
Recorder+VCR.
See ‘Changing the TV Audio Channel‘ on
page 31.
Point the remote control at the remote
sensor of the DVD Recorder+VCR.
Remote control does not
work properly.
The remote control is too far from
the DVD Recorder+VCR.
There is an obstacle in the path of
the remote control and the DVD
Recorder+VCR.
Operate the remote control within 23 ft
(7m).
Remove the obstacle.
The batteries in the remote control
are dead.
Replace the batteries.
5 4
5 5
Te ch n ica l Sp e cifica tio n s
Te ch n ica l Sp e cifica tio n s
Frequency response DVD (PCM 48 kHz): 8 Hz to 22
kHz, CD: 8 Hz to 20 kHz
Ge n e ra l
Video S/N
Audio S/N
More than 60dB
More than 90dB
Power requirements 200-240V,50/60Hz
Power consumption Maximum 26W (Stand-by :3.7W)
Dimensions (approx.)
Harmonic distortion Less than 0.06%
Dynamic range
Resolution
More than 90 dB
over 500 lines (HQ Recording)
430 *92 *312 (w*h*d)
4.96 Kg
Mass (approx.)
Operating temperature
5°C to 35°C
Operating humidity 5% to 90%
In p u ts
ANTENNA IN
VIDEO IN
Antenna or CATV input, 75 Ω
1.0 Vp-p 75 Ω, sync negative,
RCA jack x 2
Signal system
PAL
Re co rd in g
Recording formats DVD Video Recording, DVD-
VIDEO
AUDIO IN
-8.8 dBm more than 47 k, RCA
jack (L, R) x 2
DV IN (Optional)
O u tp u ts
4 pin (i.LINK/IEEE 1394 standard)
Recordable discs
DVD+R, DVD+RW, DVD-R, DVD-
RW
[DVD] Approx 1 Hour (HQ mode),
2 Hours (SP mode), 4 Hours (EP
mode), 8 Hours (SEP mode)
[VCR] SP: 3 Hours (E-180), LP : 6
Hours (E-180)
VIDEO OUT
Composite output (1.0 Vp-p,
unbalanced) RGB output (75 in
load, R:0.7Vp-p, G:0.7Vp-p,
B:0.7Vp-p)
Recordable time
S-VIDEO OUT (Y)
1.0 V (p-p), 75 Ω, negative sync,
Mini DIN 4-pin x 1, (C) 0.286 V
(p-p) 75 Ω
Vid e o re co rd in g fo rm a t
Sampling frequency 27MHz
Compression format MPEG 2
Au d io re co rd in g fo rm a t
COMPONENT VIDEO OUT
(Y) 1.0 V (p-p), 75 Ω, negative
sync, RCA jack x 1
(Progressive Scan) (Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA
jack x 2
Sampling frequency 48kHz
Compression format MPEG1 Layer2
VCR Sp e cifica tio n s
Head system
AUDIO OUT
Digital audio : 0.5 V (p-p), 75 Ω,
RCA jack x 1
4 Head Video, 2 Head Hi-Fi
Analog audio : 1.1 Vrms (1 kHz, -
6 dB), 600 Ω, RCA jack (L, R) x 2
CH.52 (default)
helical scan azimuth system
24-hour display type
SP: 23.39 mm/sec, LP: 11.70
mm/sec
Timer
Tape speed
RF OUT
Acce sso rie s
Tape width
12.7 mm
Rewind time
less than 150 sec (E-180)
Scart cable (Only for france) .....................................1
RF Coaxial Cable ...................................................... 1
Blank DVD+RW disc ................................................ 1
Remote control ........................................................ 1
Batteries .................................................................. 2
Channel coverage VHF:2-12,13-20,74-80 / UHF:21-
69 / CATV:1-41
Frequency range
Signal-to-noise ratio 43 dB
Dynamic range 75 dB
20Hz to 20kHz
Channel separation 45 dB
Design and specifications are subject to change
without notice.
DVD Sp e cifica tio n s
Laser system
Semiconductor laser,
wavelength 650 nm
Manufactured under license from Dolby Laboratories. ‘Dolby‘ and the double-D symbol are trademarks of
Dolby Laboratories.
DTS and DTS Digital Out are registered trademarks of Digital Theater Systems, Inc.
Macrovision
This product incorporates copyright protection technology that is protected by method claims of certain U.S
patents and other intellectual property rights owned by Macrovision Corporation and other rights owners.
Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended
for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
5 6
|