IMPORTANT SAFEGUARDS
HOW TO GET THE MOST ENJOYMENT FROM YOUR NEW COLOR TV SET
Your new Color TV incorporates a host of features designed to give you excellent performance.
In addition, this model utilizes a highly sophisticated Control Microprocessor that can give
you unprecedented convenience and control in the areas of Picture Adjustment, Channel
Tuning, On-Screen Information.
We therefore strongly urge that you read all of these instructions before using your TV for
the first time.
It is especially important that you read and follow the instructions under the heading:
"CHANNEL MEMORY" on page 16.
SAFETY INSTRUCTION
ANTENNA
OWNER' S MANUAL
Unless your TV is connected to a Cable TV system or to a centralized antenna system, a good
outdoor color TV antenna is recommended for the best performance. However, if you are
located in a strong signal area that is free from interference and ghost conditions (multipath),
an indoor antenna may be insufficient. The two pole antenna packed with this set is for your
convenience only. It is not capable of providing you with the sharp detail and rich color that this
television was designed to display.
DDQ-9 H1 S C
LOCATION
Select an area where sunlight or bright indoor illumination will not fall directly on the picture
screen.
Also, be sure that the location selected allows a free flow of air to and from the perforated back
cover of the set.
NOTES
Never remove the back cover of the set. This can expose you to very high voltage and other
hazards.
If the set does not operate properly, unplug it and call your dealer or service shop.
VIEWING
This color receiver may be viewed from any desired distance. Most viewers prefer a distance
of three to six feet or more depending on-screen size for maximum eye comfort.
Caution
To prevent electric shock do not use this (polarized) plug with an extension cord, receptacle or
other outlet unless the blades can be inserted to prevent blade exposure.
BEFORE USING TELEVISION RECEIVER,
READ AND OBSERVE ALL OF THIS OWNER’S MANUAL.
Part No. 11906570B
2
LOCATION OF CONTROLS
CONNECTING EXTERNAL EQUIPMENT
AUDIO/VIDEO IN JACK
If your receiver has AUDIO/VIDEO IN JACK, connect this JACK to VCR and TV receiver.
Select AV by pressing the AV mode selection key on the remote control.
Push PLAY key of your VCR. The advantage of this connection is a superior quality of picture
and sound during play back.
ANTENNA
To "RF IN"
From Audio/Video Out (VCR)
To Audio/Video Input(TV)
OR
ANTENNA
To "RF IN"
To Audio/Video Input(TV)
From Audio/Video Out (VCR)
5
6
CONNECTING EXTERNAL EQUIPMENT
ANTENNA CONNECTION
Antenna
EARPHONES
The antenna requirements for a good color television reception are more important than those
for black & white television reception. For this reason,a good quality of outdoor antenna is
strongly recommended.
The earphones must have an impedance of between 8 and 32 ohms and have a 3.5mm
stereo jack plug.
1. Plug the earphone jack into the earphone socket on the right hand side of the TV.
2. Adjust the volume of sound using VOL-,+ buttons.
The following is a brief explanation of the type of connections that are provided with the various
antenna systems:
NOTE : If earphone is inserted there will be no sound output at the loud speaker.
1. A 75 ohm system is generally a round cable
with F-type connector that can easily be
attached to a terminal without tools.
F-type connector
75-ohm coaxial cable (round)
300-ohm twin-lead cable (flat)
2. A 300 ohm system is a flat "twin-lead" cable
that can be attached to a 75 ohm terminal
through a 300-75 ohm ADAPTOR.
VCR OPERATION BY USING THE RF OUT
To connect a home VCR to the receiver, connect the coaxial cable from the RF OUT
socket of the VCR to the antenna socket of the TV SET, and connect the antenna lead-in
cable to the RF IN socket of the recorder.
(Refer to 300-75 ohm ADAPTOR as supplied)
OUTDOOR ANTENNA CONNECTION
Coaxial cable
Use one of the following two diagrams if you connect an outdoor antenna.
A : Using a VHF/UHF combination outdoor antenna.
ANTENNA
To "RF IN"
To "RF OUT"
B : Using separate VHF and/or UHF outdoor antenna.
Connect an outdoor antenna cable lead-in to the COAXIAL CABLE CONNECTOR on the rear
of the TV set.
A. Combination VHF/UHF Antennas
VHF/UHF ANTENNA
300/75-ohm
ADAPTOR
(as supplied)
To antenna socket
VHF/UHF ANTENNA
300-ohm
twin-lead
or
75-ohm coaxial cable
ANT/
CABLE
REAR OF TV
75Ω
B. Separated VHF/UHF Antennas
VHF ANTENNA UHF ANTENNA
REAR OF TV
300-ohm
twin-lead
COMBINER
(not supplied)
300-ohm
twin-lead
ANT/
CABLE
IN OUT
or
75-ohm
coaxial cable
75Ω
7
8
CABLE TV(CATV) CONNECTION
VIDEO/AUDIO CONNECTIONS
Prior to making any connections to your TV set, be sure to turn the POWER off.
For a more detailed understanding of each connection, it is recommended that you read the
instruction manual for each connected component.
A 75 ohm coaxial cable connector is built into the set for easy hookup.
When connecting the 75 ohm coaxial cable to the set, screw the 75 ohm cable to the
COAXIAL CABLE CONNECTOR.
If you use video or audio equipment placed near the Monitor/Receiver,picture and/or sound
may become distorted due to interference between these components.
Some cable TV companies offer "premium pay channels". Since the signals of these premium
pay channels are scrambled, a cable TV converter/descrambler is generally provided to the
subscriber by the cable TV company. This converter/descrambler is necessary for normal
viewing of the scrambled channels. (Place your TV on channel 3 or 4, typically one of these
channels is used. If this is unknown, consult your cable TV company. One possible method of
utilizing the converter/descrambler provided by your cable TV company is explained below.
In such a case,separate each piece of equipment at a sufficient distance.
The following shows examples for connecting external equipment.
Do not connect another audio source to the same speaker to which the TV set is connected,
otherwise damage may result to the amplifier of the TV set or to that of the other audio source.
NOTE : RF switch equipped with position A/B(not provided) is required.
75 ohm
ANT
VCR or VDP
"A" position on the RF switch (not supplied)
TO VIDEO OUT
TO AUDIO OUT
TO VIDEO IN
TO AUDIO IN
: You can view all unscrambled channels using the TV's channel keys.
"B" position on the RF switch (not supplied)
: You can view the scrambled channels via the converter/descrambler using the converter's
channel keys.
VHF/ UHF
OUTPUT
VIDEO AUDIO
RF switch (not supplied)
Two-set
signal
splitter
(not supplied)
A
Cable TV line
OUT
IN
AUDIO/VIDEO INPUT
B
1.Connect the VIDEO OUT jack from the VCR to the VIDEO IN jack on the TV.
2.Connect the AUDIO OUT jack from the VCR to the AUDIO IN jack on the TV.
3.Turn TV on and press VIDEO button on the Remote control to select VIDEO mode.
4.Turn the VCR on and Playback tape.(consult your VCR system's owner's manual.)
OUT
IN
TV
Cable TV converter/
descrambler
9
10
REMOTE CONTROL USE
TV FUNCTION & OPERATION
Connect either Antenna or Cable TV according to "ANTENNA CONNECTION"
instruction on page 8.
Insert batteries into the Remote Control unit according to "REMOTE CONTROL USE"
instruction on page 11.
Connect the power cord to AC outlet.
– Voltage is between 120 Volts.
Correct
Point at the Remote Control Sensor of the TV set.
The maximum operable distance is approximately 6m from the Remote Control Sensor, and
not more than 30 to either side of center.
The operation of the Remote Control is most effective when there is nothing between it and
the Remote Control Sensor.
The duration of the batteries is approximately 6 months to 1 year.
Replace the batteries when the remote control operation becomes unstable.
– Frequency is compatible (50/60Hz)
POWER ON
Battery Installation/Notes
Press the indentation and lift up the cover in the direction of the arrow.
1) Press the MAIN POWER switch on the control panel of the set to turn on and stand-by
RED LED will illuminate.
Correctly install the batteries, observing
polarities as shown
2) The TV set is now in stand-by mode, to turn it on press CH
key located front panel
Do not use a combination of old and new batteries or batteries of different types.
If batteries become exhausted, remove and replace them soon.
When battery leakage occurs, clean the battery compartment with a soft cloth and replace the
batteries.
of the set or press power or CH
The NO LED will illuminate.
key on the remote control hand unit.
or
or
Direct channel
100 Button
Remote control
(Front panel)
POWER OFF
selection Buttons
1) Press the POWER key on the remote control hand unit.
The RED LED will illuminate.
2) If you want to turn off for a long time, Press the MAIN POWER switch on the control panel.
3) When there is no broadcasting signal, the TV set goes off automatically after 15 minutes.
In this case, the TV set goes to stand-by mode, there for The RED LED will illuminate.
This function is the same as in the AV mode.
TV/Video Button
TV Menu Button
Power Button
Mute Button
DVD Control Button
NOTE : Power button of front panel is not active when you use the DC battery cord.
Display Button
Channel Down( )/
Up( ) Buttons
CHANNEL SELECTION
MTS Button
DVD 3D Button
Use CHANNEL (
front panel).
) buttons on the Remote Control (or CHANNEL (
) buttons on the
Volume Down(-)/
Up(+) Buttons
Pressing the ( ) button to advances for the higher channels, and press the ( ) button to go
down for the lower channels.
NOTE : Certain channels have been preset at the factory. It may be necessary to add or
erase some channels in your areas. See "AUTO PROGRAM" on page 17 for
presetting channels.
Quick View Buttons
Add/Delete Buttons
DVD Function Buttons
Channels can be selected directly by using 10-Digit Keypad on the Remote Control.
For example, if you select channel 5, press "0" first, then press "5". (Be sure to press "0" first,
before pressing "5" for channel 5.)
For channel 120, press the 100 button first, then press "2", "0". Also refer to the CABLE
CHANNEL CONVERSION CHART below.
NOTICE : To select channels (to jump directly to a desired channel)100 through 125, press the
"1" button for 2 second and then the last two digits within a few seconds after
pressing the " 1" button.
11
12
ON SCREEN LANGUAGE SELECTION
1) Press the TV MENU button.
CABLE TV CHANNEL CONVERSION CHART
MENU
2) Press the CHANNEL UP/DOWN
reach LANGUAGE mode.
button to
PICTURE
In addition to the normal TV reception from an antenna for VHF (Channels 2-13) and UHF
(Channel 14-69), your TV set is equipped to receive non-scrambled cable TV channels.
SOUND
TIME
SETUP
FUNCTION
LANGUAGE ENGLISH
3) Press the
language.
or VOLUME+ button to select the desired
SubMid band (A-8, A-5-A-1), Mid band (A-I) Super band (J-W) Hyper band (W
1
-
W
28)
and Ultra band (W 29 - W 84) can be received by using the channel selections as shown in
the following chart.
4) It will appear on the screen like below;
ENGLISH ESPAÑOL PORTUGUÊS
FRANÇAIS
: MOVE
: ADJ.
: EXIT
A-5
95
P
A-8
01
O
A-4 A-3 A-2 A-1
A
14
U
B
15
V
C
D
E
F
G
H
I
J
K
L
M
N
96
Q
97
R
98
S
99
T
16
W
36
17
W
18
W
19
W
20
W
21 22
W
23 24
25
W
26
27
5) Press the TV MENU button to exit.
1
2
3
4
5
W
6
W
7
W
44
8
9
W
10
46
29
65
48
84
67
28 29
11 12
47 48
30 31
66 67
49 50
85 86
68 69
30
31
32
33
34
35
37
20
56
39
75
58
38
21
57
40
76
59
39
22
58
41
77
60
40 41
23 24
59 60
42 43
78 79
61 62
42 43
25 26
61 62
44 45
80 81
63 64
45
28
64
47
83
66
W
W
W
13
49
32
68
51
87
70
W
14
50
33
69
52
88
71
W
15
51
34
70
53
89
72
W
16
52
35
71
54
90
73
W
17
53
36
72
55
91
74
W
18
54
37
73
56
92
75
W
19
55
38
74
57
93
76
W
W
W
W
W
W
W
W
W
27
63
W
W
BASIC OPERATION
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
46
W
W
82
1. Press POWER button to turn the TV on.
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
65
W
W
2. Press TV MENU button and move the cursor to "SET UP" option and press
button, then the "SET UP" menu is displayed.
or VOLUME+
94 100 101 102 103 104 105 106 107 108
77 78 79 80 81 82 83 84
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125
MENU
SET UP
Regular cable channel designations.
PICTURE
SOUND
Your TV set's corresponding on-screen CABLE channel numbers.
ANTENNA
CATV 2
0
AUTO PROGRAM
FINE TUNE
TIME
SETUP
Press VOLUME
buttons on either the
FUNCTION
LANGUAGE ENGLISH
Remote Control or(
desired listening level.
) front panel to adjust volume to your
or
Pressing the
button will increase
button will
:
MOVE
:
SELECT
:
PREV.
:
MOVE
:
SELECT
:
EXIT
VOLUME
ADJ.
25
sound volume, the
decrease sound volume.
3. Press VOLUME
button to Select ANTENNA option.(TV or CATV)
The volume level is indicated on the
screen by reference number (0-100)and by bar scale as shown.
4. Press CH
+ button.
/
buttons to place cursor on the "AUTO PROGRAM " option and press VOL
SET UP
NOTES The volume level can be muted instantly by pressing MUTE button on the Remote
Control. See "MUTE Button" on page 34.
ANTENNA
AUTO PROGRAM
FINE TUNE
CATV 2
0
Your TV set can receive the normal TV channel(2-13) including the CABLE TV
channel
AUTO PROGRAMMING
2
or
NOTE TO CATV SYSTEM INSTALLER
:
STOP
:
MOVE
:
SELECT
:
PREV.
This reminder is provided to call the CATV system installer’s attention to article 820-40 of the
NEC that provides guidelines for proper grounding and, in particular, specifies that cable ground
shall be connected to the grounding system of the building, as close to the point of cable entry as
practical.
5. Press CH
/
buttons to Select the channel you want.
6. Press VOL + or VOL - buttons to adjust volume to your desired listening level.
13
14
BASIS OF "MENU" OPERATION METHOD
CHANNEL MEMORY(SET UP)
You can execute every operation by pressing CH
alternately.
/
buttons and VOL +/- or
buttons
ANTENNA SELECTION
In this mode, you can change the broadcast mode between
channels) and " CATV " (for cable channels).
"TV" (for regular VHF/UHF
If you learn one method, You can easily operate another function by viewing picture.
1. Pressing these buttons alternately makes
every operation easy.
1. Press TV MENU button and move the cursor to "SET UP" option and press VOL + or
button then the "SET UP" menu is displayed.
2. MOVE
cursor.
Press CH
/
buttons to place
MENU
SET UP
3. PICTURE CHANGE Press VOL +/- or
buttons to change picture by inputting
selected function.
PICTURE
SOUND
ANTENNA
CATV 2
AUTO PROGRAM
FINE TUNE
TIME
SETUP
0
FUNCTION
MENU
LANGUAGE
ENGLISH
: SELECT : EXIT
PICTURE
SOUND
: MOVE
: SELECT
: PREV.
: MOVE
TIME
SETUP
2. Press CH
/
buttons to place the cursor on the "ANTENNA" option and press VOL + or
FUNCTION
LANGUAGE
ENGLISH
button. You can select "TV"(on-air) or "CATV"(cable TV) broadcast mode.
:
MOVE
:
SELECT
:
EXIT
SET UP
SET UP
TIME
SET UP
ANTENNA
CATV 2
ANTENNA
TV 2
AUTO PROGRAM
FINE TUNE
AUTO PROGRAM
FINE TUNE
CLOCK
SLEEP
TIMER
ON TIME
OFF TIME
ON CHANNEL
AM12:00
OFF
OFF
AM12:00
AM12:00
2
ANTENNA
AUTO PROGRAM
FINE TUNE
CATV2
0
0
0
: MOVE
: SELECT
: PREV.
: MOVE
: SELECT
: PREV.
: MOVE
: SELECT
: PREV.
: MOVE
: SELECT
: PREV.
3. After you have finished selecting "ANTENNA" mode, press TV MENU button repeatedly until
the menu disappears.
PICTURE
PICTURE
CONTRAST
BRIGHTNESS
SHARPNESS
COLOR
FUNCTION
SOUND
SOUND
EQUALIZER
BALANCE
SURROUND
AVL
STANDARD
BLUE BACK
HALF TONE
CCD
ON
ON
OFF
STANDARD
75
50
50
50
0
0
OFF
OFF
TINT
: MOVE
: ADJ.
: PREV.
: MOVE
: ADJ.
: PREV.
: MOVE
: ADJ.
: PREV.
15
16
CHANNEL MEMORY(SET UP)
CHANNEL MEMORY(SET UP)
AUTO PROGRAM
MANUAL MEMORY(channel add/delete)
This function allows the channels to be memorized automatically to match the TV broadcasts
and cable channels in your area.
1. TO ADD A CHANNEL
If you want to add to the memory a channel the TV did not store during AUTO PROGRAM,
follow these steps.
1. Press TV MENU button and move the cursor to "SET UP" option and press VOL + or
button, then the "SET UP" menu is displayed.
Press the 10-Digit Keypad button to select a channel you want to view.
Press
"A/D" button on the Remote Control.
MENU
SET UP
The channel is added to memory and the color of the channel number changes from red
to green.
PICTURE
SOUND
TIME
SETUP
ANTENNA
AUTO PROGRAM
FINE TUNE
CATV 2
0
CH DELETING
CH ADDING
FUNCTION
LANGUAGE
ENGLISH
: SELECT : EXIT
CATV 12
CATV 12
: MOVE
: SELECT
: PREV.
: MOVE
CHANNEL ADDED
CHANNEL DELETED
2. Press CH
or button.
/
buttons to place cursor on the "AUTO PROGRAM" option and press VOL +
SET UP
COLOR : GREEN
COLOR : RED
ANTENNA
CATV 2
AUTO PROGRAM
FINE TUNE
2. TO DELETE CHANNEL
0
You can exclude the channels of your choice from the memorized channel.
Follow these steps to delete the channel in the TV's memory.
AUTO PROGRAMMING
2
:
STOP
: MOVE
: SELECT
: PREV.
Press CH
to delete.
/
buttons or Press the 10-Digit keypad button to select a channel you want
Press "A/D" button on the Remote Control.
When tuned to a channel in which TV program is broadcasted, this channel is memorized and
the color changes from magenta to green.
The channel is removed from the memory, and the color of the channel number changes
from green to red.
After every channels were memorized, "SET UP" menu is displayed.
3. When you have finished "AUTO PROGRAMMING", press TV MENU button repeatedly until
the menus disappear.
NOTES
If the broadcast signal is weak, the channel will not be memorized.
In this case, perform the MANUAL MEMORY procedure.(Refer to the next page)
If you wish to stop this procedure during the operation, Press VOL + or
button.
17
18
CHANNEL MEMORY(SET UP)
PICTURE ADJUSTMENT 1
USING ON-SCREEN MENU
FINE TUNE
You can sequentially select any one of the four possible preferred analogue picture presets.
If the reception is clear, you do not have to fine-tune the channel, as this is done automatically
during auto program and manual memory.
MENU
If however the signal is weak or distorted, you may have to fine-tune the channel manually.
1
PICTURE
SOUND
1. Press CH
/
buttons or Press the 10-Digit keypad button to adjust a channel you want.
Press the TV MENU button. Move the
cursor to PICTURE by pressing the CH
TIME
SETUP
2. Press TV MENU button and move the cursor to "SET UP" option and press VOL + or
button, then the "SET UP" menu is displayed.
FUNCTION
LANGUAGE ENGLISH
/
buttons and press the VOL + or
button.
MENU
SET UP
:
MOVE
:
SELECT
:
EXIT
PICTURE
SOUND
TIME
SETUP
ANTENNA
AUTO PROGRAM
FINE TUNE
CATV 2
PICTURE
2
3
0
PICTURE
STANDARD
FUNCTION
CONTRAST
BRIGHTNESS
SHARPNESS
COLOR
75
50
50
50
0
LANGUAGE
ENGLISH
: SELECT : EXIT
Move the cursor to PICTURE by
pressing the CH buttons.
/
: MOVE
: MOVE
: SELECT.
:PREV.
TINT
3. Press CH
/
buttons to place the cursor on the "FINE TUNE" option.
4. Use VOL +/- or
buttons until you obtain a sharp and clear picture and good sound quality.
: MOVE
: ADJ.
: PREV.
SET UP
SET UP
PICTURE
ANTENNA
AUTO PROGRAM
FINE TUNE
CATV 2
ANTENNA
AUTO PROGRAM
FINE TUNE
CATV 2
Press the VOL +/- or
button.
PICTURE
CONTRAST
BRIGHTNESS
SHARPNESS
COLOR
DYNAMIC
100
50
75
50
0
Whenever this button is pressed, the
mode will change as follows.
0
+1
STANDARD
CUSTOM
DYNAMIC
MILD
A/D:MEMORY
A/D:MEMORY
TINT
: MOVE
: ADJ.
:PREV.
: MOVE
: ADJ.
:PREV.
: MOVE
: ADJ.
: PREV.
5. If you wish to memorize adjusted FINE TUNE state, press "A/D" button, and then the memorie
icon is displayed.
MODE
PICTURE
If you wish to initialize it, press that button again, and then the icon disappear.
STANDARD
Select this mode to view the factory-presetting standard picture.
NOTES
The memorized channel does not operate AFT(automatic frequency tuning)mode.
The FINE-TUNE is operated only selected channel.
Select this mode to view a powerful and clear picture.
- watch in the brighter(daylight) environments.
DYNAMIC
After the "AUTO PROGRAM", the memorized channel operate AFT(automatic
frequency tuning)mode automatically.
Select this mode to emphasize mildness
- When it is dark around to lessen the fatigue of eyes.
MILD
Select this mode to view the adjusted picture you want.
CUSTOM
19
20
PICTURE ADJUSTMENT 2
SOUND ADJUSTMENT
You can sequentially select and adjust one of five picture levels.
Contrast, Brightness, Color, Sharpness or Tint
USING ON-SCREEN MENU
There is a choice of five audio settings by using the on-screen menu, the five settings can by viewed in
the sequence illustrated.
e.g. : Contrast Adjustment.
MENU
1
PICTURE
SOUND
TIME
SETUP
FUNCTION
LANGUAGE ENGLISH
Press the TV MENU button. Move the
MENU
1
cursor to SOUND by pressing the CH
PICTURE
SOUND
TIME
SETUP
FUNCTION
LANGUAGE ENGLISH
Press the TV MENU button. Move the
cursor to PICTURE by pressing the CH
buttons and press the VOL + or
button.
/
buttons and press the VOL + or
button.
/
:
MOVE
:
SELECT
:
EXIT
:
MOVE
:
SELECT
:
EXIT
SOUND
2
3
PICTURE
SOUND
EQUALIZER
BALANCE
SURROUND
AVL
STANDARD
2
Move the cursor to SOUND by pressing
PICTURE
CONTRAST
BRIGHTNESS
SHARPNESS
COLOR
STANDARD
0
OFF
OFF
the CH
/
buttons.
75
50
50
50
0
Move the cursor to CONTRAST by
pressing the CH
/
buttons and
buttons.
press the VOL +/- or
: MOVE
: ADJ.
: PREV.
TINT
: MOVE
: ADJ.
: PREV.
75
SOUND
SOUND
MUSIC
Press the VOL + or
button.
3
4
EQUALIZER
BALANCE
SURROUND
AVL
CONTRAST
Whenever this button is pressed, the
mode will change as follows.
0
OFF
OFF
Adjust "CONTRAST" by VOL +/- or
buttons.
: ADJ.
: PREV.
: MOVE
: ADJ.
: PREV.
STANDARD
MUSIC
MOVIE
SPEECH
CUSTOM
When you have finished contrast adjustment,
press TV MENU repeatedly until the menu
disappears.
STANDARD
MUSIC
Select this mode to use the factory presetting.
Select this mode when listening to music
Select this mode when viewing a movie.
Select this mode to hear voices clearly.
MOVIE
SPEECH
CUSTOM
Select this mode to hear the adjusted sound you want. See EQUALIZER page.
21
22
SOUND ADJUSTMENT
SOUND ADJUSTMENT
EQUALIZER
BALANCE
You can adjust five frequency ranges to your preference.
SOUND MENU
MENU
MENU
1
1
Press the TV MENU button. Move the
cursor to SOUND by pressing the CH
PICTURE
SOUND
TIME
PICTURE
SOUND
TIME
Press the TV MENU button. Move the
cursor to SOUND by pressing the CH
/
buttons and press the VOL + or
/
buttons and press the VOL + or
SETUP
SETUP
FUNCTION
LANGUAGE
button.
FUNCTION
LANGUAGE
button.
ENGLISH
: SELECT : EXIT
ENGLISH
: SELECT : EXIT
: MOVE
: MOVE
2
3
2
3
SOUND
SOUND
SOUND
STANDARD
SOUND
STANDARD
Move the cursor to BALANCE by
Move the cursor to EQUALIZER by
EQUALIZER
BALANCE
SURROUND
AVL
EQUALIZER
BALANCE
SURROUND
AVL
pressing the CH
/
buttons.
0
OFF
OFF
0
OFF
OFF
pressing the CH
press the VOL + or
/
buttons and
button.
: MOVE
: ADJ.
: PREV.
: MOVE
: ADJ.
: PREV.
EQUALIZER
BALANCE
: ADJ.
0
Press the VOL +/- or
buttons.
50
50
50
50
50
The Sound BALANCE is adjusted.
Adjust each frequency band, using
CH buttons.
: PREV.
/
120 500 1.5K 5K
: ADJ : MOVE
10K
: PREV.
23
24
SOUND ADJUSTMENT
SOUND ADJUSTMENT
SURROUND SOUND
AVL
SOUND MENU
SOUND MENU
MENU
MENU
1
1
Press the TV MENU button. Move the
cursor to SOUND by pressing the CH
Press the TV MENU button. Move the
cursor to SOUND by pressing the CH
PICTURE
SOUND
TIME
PICTURE
SOUND
TIME
/
buttons and press the VOL + or
/
buttons and press the VOL + or
SETUP
FUNCTION
SETUP
FUNCTION
button.
button.
LANGUAGE
ENGLISH
: SELECT : EXIT
LANGUAGE
ENGLISH
: SELECT : EXIT
: MOVE
: MOVE
SOUND
SOUND
2
3
2
3
SOUND
STANDARD
SOUND
STANDARD
Move the cursor to SURROUND by
Move the cursor to AVL by pressing the
EQUALIZER
BALANCE
SURROUND
AVL
EQUALIZER
BALANCE
SURROUND
AVL
pressing the CH
/
buttons.
CH
/
buttons.
0
OFF
OFF
0
OFF
OFF
: MOVE
: ADJ.
: PREV.
: MOVE
: ADJ.
: PREV.
Press the VOL + or
buttons.
Press the VOL + or
buttons.
Whenever this button is pressed, the mode will change as follows.
Whenever this button is pressed, the mode will change as follows.
OFF
ON
OFF
ON
AVL(Automatic Volume Limitter)
Different sound sources fairly do not have the same volume level.
This results in annoying volume changes.
AVL solves the problem by equalizing the volume levels.
25
26
SOUND ADJUSTMENT
TIME SETTING
MTS
CLOCK
You can set the television’s clock so that the current time will be displayed when you press the
USING MTS BUTTON :
TV MENU button.
Your TV set incorporates an MTS (Multichannel Television Sound) decoder to receive stereo
broadcasts and any accompanying SAP (Second Audio Program) such as another language
sound track).
You must set the current time before you can set the automatic On/Off timer.
1. Press the MTS button
Depending on the audio signal type of the currently receiving broadcast, on-screen selection
appears as follows:
MENU
1
Press TV MENU button and move the
PICTURE
SOUND
cursor to TIME by CH
/
buttons.
Receiving signal
On-screen selections
STEREO SAP MONO
TIME
SETUP
FUNCTION
LANGUAGE
Press VOL + or
again.
button and press it
Stereo and SAP
ENGLISH
: SELECT : EXIT
Stereo or SAP
Mono
STEREO
MONO or SAP
MONO
: MOVE
MONO only
GREEN
TIME
WHITE
2
3
4
The "STEREO", "SAP" text indicate that MTS mode is being broadcast.
CLOCK
SLEEP
TIMER
ON TIME
OFF TIME
ON CHANNEL
AM12:00
OFF
OFF
AM12:00
AM12:00
2
Adjust "HOUR" by CH
/
buttons.
When the power is switched on or channel is changed, the "STEREO", "SAP" text are
automatically displayed, depending on the current broadcast.
Whenever these buttons are pressed,
the hour increases or decreases by 1.
: ADJ.
TIME
: MOVE
: PREV.
MTS STEREO
WHITE
GREEN
Press VOL + or
button and adjust
buttons.
CLOCK
SLEEP
TIMER
ON TIME
OFF TIME
ON CHANNEL
AM12:00
OFF
OFF
AM12:00
AM12:00
2
NOTES
"MINUTE " by CH
/
If the received signal is weak, noise may be heard.
Whenever these buttons are pressed,
the minute increases or decreases
by 1.
In such a case, press MTS button to set to the MONO mode for better sound reception.
If the received SAP signal is weak, the SAP will not be heard.
Even if both STEREO and SAP broadcasts are received, both broadcasts cannot be
heard at the same time.
: ADJ.
: MOVE
: PREV.
Transmission of CABLE TV signals may differ from off-air TV broadcasts.
Press the TV MENU button to return
to the main menu.
27
28
TIME SETTING
TIME SETTING
ON/OFF TIMER
SLEEP TIMER
The ON/OFF time lets you use alarm and automatic off function.
You can select a time period from 15 through 90 minutes so that the television automatically
switches to power-off mode.
Press TV MENU button.
Move the cursor to TIME by pressing the
MENU
1
2
MENU
PICTURE
SOUND
TIME
SETUP
FUNCTION
LANGUAGE
1
CH
or
/
buttons and press the VOL +
PICTURE
SOUND
TIME
SETUP
FUNCTION
LANGUAGE
Press TV MENU button the cursor to
button.
TIME by pressing the CH
/
button and press the VOL + or
button.
"TIME " is displayed on the screen.
ENGLISH
: SELECT : EXIT
ENGLISH
: SELECT : EXIT
: MOVE
: MOVE
TIME
Move the cursor to Timer by CH
buttons and press VOL + or
to set "TIMER ON"
/
TIME
button
2
CLOCK
SLEEP
TIMER
ON TIME
OFF TIME
ON CHANNEL
AM12:00
OFF
ON
AM12:00
AM12:00
2
"TIME " is displayed on the screen.
CLOCK
SLEEP
TIMER
ON TIME
OFF TIME
ON CHANNEL
AM12:00
OFF
OFF
AM12:00
AM12:00
2
Move the cursor to SLEEP by CH
buttons and press the VOL + or
button to set SLEEP time.
/
Whenever VOL + or
button is
pressed, the time is changed.
: ADJ.
: MOVE
: PREV.
: ADJ.
: MOVE
: PREV.
NOTES If you have not yet set the television’s clock, the message "CLOCK STOPPED" is
displayed.
OFF
15
30
45
60
90
If this happens, refer to "CLOCK" on the previous page.
NOTE : To cancel the sleep timer function, in this mode, press VOL + or
button
repeatedly until the word " OFF " is displayed.
29
30
TIME SETTING
TIME SETTING
ON TIME CHANNEL NUMBER
You can select the channel on which the TV turns on as programmed by ON-TIMER.
This function will not work if the TIMER is set to OFF or the current time has not been set.
TIME
4
CLOCK
SLEEP
TIMER
ON TIME
OFF TIME
ON CHANNEL
AM12:00
OFF
ON
AM07:30
AM12:00
2
Move the cursor to "ON TIME" by CH
buttons and press the VOL +/- or
buttons to set the time.
/
TIME
1) Move cursor to ON CHANNEL and
CLOCK
SLEEP
AM12:00
OFF
press VOL + or
button the color of
the channel number changes to white.
2) Set channel number you want use
TIMER
ON
ON TIME
OFF TIME
ON CHANNEL
AM07:30
PM10:15
2
: ADJ.
TIME
: MOVE
: PREV.
CH
/
buttons.
5
6
: ADJ.
: MOVE
: PREV.
CLOCK
SLEEP
TIMER
ON TIME
OFF TIME
ON CHANNEL
AM12:00
OFF
ON
AM07:30
PM10:15
2
Move the cursor to "OFF TIME"by CH
buttons and press the VOL +/- or
buttons to set the time.
/
FUNCTION
: ADJ. : MOVE
: PREV.
1. Press the TV MENU button. Move the cursor to a FUNCTION by pressing the CH
buttons.
/
Adjust it by pressing the VOL + or
button.
Press "TV MENU" to return to the
main menu.
or
MENU
MENU
PICTURE
SOUND
TIME
SETUP
FUNCTION
LANGUAGE
AUTOMATIC POWER OFF MODE
FUNCTION
If the set is not switched off when the TV station stops broadcasting, it will automatically go to
PICTURE
SOUND
TIME
SETUP
FUNCTION
LANGUAGE
BLUE BACK
HALFTONE
CCD
OFF
OFF
OFF
power-off mode after about 15 minutes.
the
NOTES If you set "ON TIME" and "OFF TIME" with the same time,
will be clear and please set again the "ON/OFF TIME".
"ON/OFF TIME"
ENGLISH
: SELECT : EXIT
ENGLISH
: SELECT : EXIT
If the power is disconnected (in case of a power failure) and reapplied later, the
clock operation will stop.
: MOVE
: MOVE
: MOVE
: ADJ.
: PREV.
31
32
FUNCTION
OTHER USEFUL FUNCTIONS
QUICK VIEW Button :
BLUE BACK
Press QUICK VIEW button on the Remote Control. The previously viewed channel will
appear on the screen. Press QUICK VIEW again to switch back to the original channel.
Repeatedly pressing QUICK VIEW switches between these two channel.
When no picture signal is inputed, or the signal is weak, the screen reverts to a blue back color.
FUNCTION
FUNCTION
BLUE BACK
HALFTONE
CCD
ON
OFF
OFF
BLUE BACK
HALFTONE
CCD
OFF
OFF
OFF
DISPLAY BUTTON :
or
Press DISPLAY button on the Remote Control The channel number of the program you are
now viewing, the current time and sleep time setting are displayed.
: MOVE
: ADJ.
: PREV.
: MOVE
: ADJ.
: PREV.
On this feature disable to continue watching very weak signals.
MUTE BUTTON :
Press MUTE button on the Remote Control. The volume of the TV program being viewed will
be reduced to zero and "MUTE" will appear on the screen.
HALFTONE
You can select Halftone mode in the on-screen.
FUNCTION
FUNCTION
NOTE : Changing the audio volume also restores the sound.
BLUE BACK
HALFTONE
CCD
OFF
ON
OFF
BLUE BACK
HALFTONE
CCD
OFF
OFF
OFF
or
: MOVE
: ADJ.
: PREV.
: MOVE
: ADJ.
: PREV.
CCD
You can select closed caption mode.
In this mode, press VOL + or
button.Whenever this button is pressed.
OFF
CCD 1
CCD 2
TEXT 1
TEXT 2
FUNCTION
FUNCTION
BLUE BACK
HALFTONE
CCD
OFF
OFF
CCD1
BLUE BACK
HALFTONE
CCD
OFF
OFF
OFF
or
: MOVE
: ADJ.
: PREV.
: MOVE
: ADJ.
: PREV.
33
34
DVD FUNCTION & OPERATION
INTRODUCTION
Manufactured under license from Dolby Laboratories.
"Dolby" and the double-D symbol are trademarks of Dolby Laboratories.
35
36
Disc Requirements/Copyright Information
Remote Control Unit (DVD)
1. OPEN/CLOSE BUTTON
Use this button to open/close the disc tray.
Pressing this button will while on TV/Video mode will automatically change it to DVD mode.
2. PLAY/PAUSE BUTTON
Use this button to play or pause the disc. Pressing this button during play, cause the disc
pause if in pause mode it function as the play.
Pressing this button will while on TV/Video mode will automatically change it to DVD mode.
3. STOP BUTTON
Use this button to stop the current playing mode.
4. SETUP BUTTON
Use this button to setup the various operation information of this unit to customize DVD
performance.
5. FF/SF BUTTON
Use this button to play the disc fast forward or slow forward. During pause or step state, the
button work as slow forward.
6. FR/SR BUTTON
Use this button to play the disc fast reverse or slow reverse. During pause or step state, the
button work as slow reverse.
7. NEXT BUTTON
Use this button to move to the next chapter (DVD).
8. PREV BUTTON
Use this button to move to the previous chapter (DVD).
9. MENU BUTTON
Use this button to display the contents menu of the loaded DVD disc. This function is disc
dependent. A DVD disc may not contain a contents menu.
10. STEP BUTTON
Use this button to play one frame at a time.
11. SUBTITLE BUTTON
Use this button to change the subtitle language to a different language or from the one selected
at the initial settings. When the loaded disc support multiple subtitle.
37
38
Remote Control Unit (DVD)
Basic Playback
12. ANGLE BUTTON
If a disc includes multi angle information, the user can watch a screen in multi angles. The
function is limited to a DVD disc supporting multi angle information.
13. ZOOM BUTTON
Use this button to enlarge DVD or DVD screen image up to 4 times. You may also move the
image using CH
,
buttons.
14. TITLE BUTTON
Use this button to display the title menu of the loaded DVD disc. This function is disc
dependent. A DVD disc may not contain a contents menu.
15. 3D BUTTON
Use this button for stereophonic sound system.
16. AUDIO BUTTON
Use this button to change the audio language to a different language from the one selected at
the initial settings, when the loaded disc supports multiple audio language.
17. REPEAT BUTTON
Use this button to set up repeat viewing during play, for repeated playback of disc titles, to
repeat the selected segment, or for specifying and repeating playback of a chapters or sound.
39
40
Searching for a specific screen/song during playback
Searching for a specific screen/song during playback
41
42
Setting a custom view
Changing the audio/subtitle language
43
44
Changing the size and angle of the screen
Selecting a menu and 3D
45
46
Using the Setup Menu
Setting the Language
47
48
Setting the Language
Setting the VIDEO
49
50
Setting the SPEAKERS
Setting the Audio
51
52
CUSTOM settings
Setting rating level and password
53
54
Operation with an MP3 disc
Operation with an MP3 disc
C:001 / T:008
55
56
Use of JPEG DISC
Use of JPEG DISC
57
58
TROUBLE SHOOTING GUIDE
TV
DVD
Before requesting service, please refer to the following chart for the symptom and possible
solution. For more information, see the corresponding page in this manual.
SYMPTOM
POSSIBLE SOLUTIONS
Make sure the power cord is plugged in.
Try another AC outlet.
Power is off, check fuse or circuit breaker.
TV does not
operate
Station or CATV experiencing problems, turn to another station.
Check sound adjustments (Volume and Mute).
Check for sources of possible interference.
Poor sound or
no sound
Station or CATV experiencing problems, turn to another station.
Check antenna or CATV connections, reorient antenna.
Check for sources of possible interference.
Poor picture or
no picture
Check picture control adjustments.
Station or CATV experiencing problems, turn to another station.
Station signal is weak, reorient antenna to receive a strong signal.
Check for sources of possible interference.
Poor reception
on some channels.
Station or CATV experiencing problems, turn to another station.
Make sure channels are set into memory.
Check picture control adjustments.
Make sure TV/CATV Mode is in the correct position.
Check antenna or CATV connections, reorient antenna.
Check for sources of possible interference.
Poor color or no
color
Station or CATV experiencing problems, turn to another station.
Make sure channels are set into memory.
CATV company is scrambling signal.
Picture wobbles
or drifts
Check antenna connections and reorient antenna.
Check CATV connections
Make sure TV/CATV is in the correct position.
Station or CATV system problems,try another station.
No CATV
reception
Check antenna connections and reorient antenna.
Make sure TV/CATV Mode in the correct position.
Check for sources of possible interference.
Horizontal or
diagonal bars
on screen
No reception above
Channel 13
Make sure TV/CATV Mode is in the correct position.
If using antenna, check UHF antenna connections.
Batteries are weak, dead, or inserted improperly.
Remote is out of range, move closer to TV.
Make sure remote is aimed at sensor.
No remote
operation
Confirm there are no obstructions between the remote and the TV.
Make sure the power cord is plugged in.
Power interrupted.
Sleep Timer , On Timer or Off Timer are set; Station has stopped
broadcasting.
TV shuts off
59
60
SPECIFICATION
INTERFERENCE CAUSES
The most up-to-date technology to eliminate an interference is incorporated in your
television receiver. Local conditions, however, can create the disturbances which visibly
affect your picture. Proper installation, good antenna connection and following advice of
your dealer are your best safeguards against the following disturbances.
Power Source
AC 120V~, 60Hz, 60W
DC 12-24V, 54W
The most common type of television disturbances are as follows:
TV Broadcasting
NTSC
IGNITION
Receiving Channels
VHF 2-13CH, UHF 14-69CH
CATV 1, 14 -125CH (T/T 181CH)
On Screen Display
Black spots or horizontal streaks may appear, picture may
flutter or drift. Usually caused by interference from
automobile ignition system, neon lamps, electrical drills
and other electrical appliances.
TV
Channel indicator
Sound Output
Speakers
GHOSTING
1.5W+1.5W (Stereo)
3W(8ohm) x 2 (Stereo)
273mm (W) x 318mm (H) x 318mm (D)
8.4Kg
Ghostings are caused by the television signal following two
paths. One is the direct path and the other is reflected from
tall buildings, hills or some other objects. Changing the
direction or position of the antenna may improve the
reception.
Dimension (W H D)
Weight
SNOW
Video Output
Audio Output
1.0Vp-p, 75 unbalanced
2.0Vrms (at 1KHz)
lf your receiver is located at the fringe area of a television
station where the signal is weak, your picture may be
blurred by the appearance of small dots. When the signal
is extremely weak, it may be necessary to install a special
antenna to improve the picture.
DVD
RADIO FREQUENCY INTERFERENCE
The interference produces moving ripples or diagonal
streaks, and in some cases, causes the loss of the contrast
in picture.
61
62
MEMO
63
64
MEMO
65
|