Daewoo CMC 710B User Manual

Service Manual

XGA COLOR MONITOR

Model : 710B

DAEWOO ELECTRONICS CO., LTD

OVERSEAS SERVICE DEPT.

SAFETY PRECAUTIONS

CAUTION: No modifications of any circuit should be attempted. Service work should only be performed after

you are thoroughly familiar with all of the following safety check and servicing guidelines.

Safety Check

Care should be taken while servicing this analog color display because of the high voltages used in the deflection

circuits. These voltages are exposed in such areas as the associated flyback and yoke circuits.

Fire & Shock Hazard

• Insert an isolation transformer between the analog color display and AC power line before servicing chassis.

• In servicing, pay attention to original lead dress especially in the high voltage circuit. if a short circuit is found,

replace all parts which have been overheated as a result of the short circuit.

• All the protective devices must be reinstalled per original design.

• Soldering must be inspected for possible cold solder points, frayed leads, damaged insulation, solder splashes

or sharp solder points. Be certain to remove all foreign materials.

Implosion Protection

Picture tube in this monitor employs integral implosion protection system, but care should be taken to avoid

damage and scratching during installation.

Use only same type replacement picture tubes.

IMPORTANT SAFETY NOTICE: There are special components used in analog color display, which are

important for safety. These parts are shaded on the schematic diagram and

on the replacement parts list. It is essential that these critical parts should be

replaced with manufacturer’s specified parts to prevent X-radiation, shock,

fire or other hazards. Do not modify the original design without getting a

written permission from DAEWOO ELECTRONICS CO. or this will void the

original parts and labor warranty.

X-Radiation

WARNING: The only potential source of X-Radiation is the picture tube. However when the high voltage circuitry

is operating properly, there is no possibility of an X-Radiation problem. The basic precaution which

must be exercised is to keep the high voltage at the following factory recommended level.

NOTE: It is important to use an accurate, periodically calibrated high voltage meter.

•

To measure the high voltage, use a high-impedance high-voltage meter.

Connect(-) to chassis and (+) to the CRT anode button.

• Turn the Contrast & brightness control fully counterclockwise.

• Measure the high voltage. The high voltage meter should indicate the following factory recommended

level.

• If the upper meter indication exceeds the maximum level, immediate service is required to prevent the

possibility of premature component failure.

• To prevent X-Radiation possibility, it is essential to use the specified picture tube.

• The normal high voltage is 26.5KV or below, and must not exceed 29KV at zero beam current at rated

voltage.

GENERAL SAFETY INFORMATION

Terms in the manual

CAUTION Statements identify conditions or practices that could result in damage to the equipment or other

property.

WARNING Statements identify conditions or practices that could result in personal injury or loss of life.

Terms as marked on equipment

CAUTION Statements indicate a personal injury hazard not immediately accessible as one reads the

marking, or a hazard to properly including the equipment itself.

WARNING Statements indicate a personal injury hazard immediately accessible as one reads the marking

Symbols in the manual

This symbol indicates where applicable cautionary or other information is to be found.

Symbols as marked on equipment

Protective GROUND terminal

High Voltage Warning And Critical Component Warning Label

Following warning label is on the CRT PWB shield case inside the unit.

Warning: This product includes critical

mechanical and electrical parts which are

essential for x radiation safety. For continued

safety, replace critical components indicated in

the service manual only with exact

replacement parts given in the parts list.

Operating high voltage for this product is 29Kv

at minimum brightness. Refer to service

manual for measurement procedures and

proper service adjustments.

SERVICING PRECAUTIONS

CAUTION: Before servicing instruments covered by this service manual, its supplements and addendum,

read and follow the SAFETY PRECAUTIONS of this manual.

NOTE: If unforeseen circumstances create conflict between the following servicing precautions and any of the

safety precautions on page 1 of this manual, always follow the safety precautions.

Remember: Safety First.

General Servicing Precautions

1. Always unplug the AC power cord from the AC power source before:

a. Removing or reinstalling any component, circuit board, module, or any other instrument assembly.

b. Disconnecting or reconnecting any electrical plug or other electrical connection.

c. Connecting a test substitute in parallel with an electrolytic capacitor in the instrument.

CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in

a explosion hazard.

d. Discharging the picture tube anode.

2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device

(DVM, FETVOM. etc.) equipped with a suitable high voltage probe. Do not test high voltage by “drawing an

arc”.

3. Discharge the picture tube anode only by: (a) first connecting one end of an insulated clip lead to the

degaussing or line grounding system shield at the point where the picture tube socket ground lead is

connected, and then (b) touching the other end of the insulated clip lead to the picture tube anode button, using

an insulating handle to avoid personal contact with high voltage.

4. Do not any spray chemicals on or near this instrument or any or its assemblies.

5. Unless specified otherwise in this service manual, clean electrical contacts by applying the following mixture to

the contacts with a pipe cleaner, cotton-tipped stick or comparable nonabrasive applicator: 10% (by volume)

Acetone and 90% (by volume) isopropyl alcohol (90%-99% strength).

CAUTION: This is a flammable mixture. Unless specified otherwise in this service manual, lubrication of

contacts is not required.

6. Do not defeat any plug/socket B+ voltage interlocks with which instruments covered by this service manual

might be equipped.

7. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device

heat sinks are correctly installed.

8. Always connect the test instrument ground lead to the appropriate instrument chassis ground before connecting

the test instrument positive lead. Always remove the test instrument ground lead last.

9. Use only the test fixtures specified in this service manual with this instrument.

CAUTION: Do not connect the test fixture ground strap to any heatsink in this instrument.

Electrostatically Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity.

Such components commonly are called Electrostatically Sensitive (ES) Devices.

The examples of typical ES devices are integrated circuits, some field-effect transistors and semiconductor “chip”

components. The following techniques should be used to help reduce the incidence of component damage

caused by static electricity.

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any

electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a

commercially available discharging wrist strap device which should be removed for potential shock reasons

prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface

such as aluminum foil to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static type solder removal device. Some solder removal devices not classified as “anti-static”

can generate enough electrical charges to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate enough electrical charges to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to

install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive

foam, aluminum foil or comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the

protective material to the chassis or circuit assembly into which the device will be installed.

CAUTION: Be sure that no power is applied to the chassis or circuit, and observe all other safety

precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmful motion such

as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate

enough static electricity to damage an ES devices).

General Soldering Guidelines

1. Use a grounded-tip, low-wattage soldering iron with appropriate tip size and shape that will maintain tip

temperature within a 550°F-660°F (288°C-316°C) range.

2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead.

3. Keep the soldering iron tip clean.

4. Thoroughly clean the surface to be soldered. Use a small wire-bristle (0.5 inch or 1.25cm) brush with a metal

handle. Do not use freon-propelled spray-on cleaners.

5. Use the following soldering technique:

a. Allow the soldering iron tip to reach normal temperature (550°F to 660°F or 288°C to 316°C)

b. Hold the soldering iron tip and solder strand against the component lead until the solder melts.

c. quickly move the soldering iron tip to the junction of the component lead and the printed circuit foil, and hold it

there only until the solder flows onto and around both the component lead and the foil.

d. Closely inspect the solder area and remove any excess or splashed solder with a small wire-bristle brush.

CAUTION: Work quickly to avoid overheating the circuit board printed foil.

FIGURE 1. USE SOLDERING IRON TO PRY LEADS

IC Removal/Replacement

Some utilized chassis circuit boards have slotted (oblong) holes through which the IC leads are inserted and then

bent flat against the circuit foil. When holes are slotted, the following technique should be used to remove and

replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in

paragraphs 5 on the page under the title of general soldering guidelines.

Removal

1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip

as the solder melts.

2. Draw away the melted solder with an anti-static suction-type solder removal device (or with desoldering braid

before removing the IC.

Replacement

1. Carefully insert the replacement IC in the circuit board.

2. Carefully bend each IC lead against the circuit foil pad and solder it.

3. Clean the soldered areas with a small wire-bristle brush. (lt is not necessary to reapply acrylic coating to the

area).

“Small-Signal” Discrete Transistor Removal/Replacement

1. Remove the defective transistor by clipping its leads as close as possible to the component body.

2. Bend the end of each of three leads remaining on the circuit board into a “U” shape.

3. Bend the replacement transistor leads into a “U” shape.

4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp

the “U” with long nose pliers to insoure metal-to-metal contact, then solder each connection.

Power IC, Transistor or Devices Removal/Replacement

1. Heat and remove all solders from the device leads.

2. Remove the heatsink mounting screw (if applicable).

3. Carefully remove the device from the circuit board.

4. Insert new device in circuit board.

5. Solder each device lead, and clip off excess lead.

6. Replace heatsink.

Diode Removal/Replacement

1. Remove defective diode by clipping its leads as close as possible to diode body.

2. Bend the two remaining leads perpendicularly to the circuit board.

3. Observing diode polarity, wrap each lead out of the new diode around the corresponding lead on the circuit

board.

4. Securely crimp each connection and solder it.

5. Inspect the solder joints of the two “original” leads on the circuit board copper side. If they are not shiny, reheat

them and apply additional solder if necessary.

TECHNICAL INFORMATION

Picture Tube

Type : 17-inch, Flat Square Tube type

(16.2-inch, viewing area)

Dot Pitch : 0.28mm

Face Treatment : Non-glare / Anti-static

Video

Input Signal : R.G.B Analog

Amp. Bandwidth : 85 MHz

Input Sync : TTL, separate negative / positive

Scan Frequency

Horizontal : 30-69 KHz

Vertical : 50-160 Hz

Max. Resolution

Power Source

Display Area

1280 dots X 1024 lines (at 60Hz)

Free Voltage (100-240 Vac, 50/60Hz)

Standard Display Area : 310mm(H)X232mm(V)

Full Screen Size : 330mm(H)X250mm(V)

Power Consumption

Max. 100W

State

Recovery Time

None

Power LED

Green

Stand-by

Green : 1 second

3 seconds

7 seconds

Suspend

Amber : 0.5 second

Off

Amber

Dimension

424(W)X440(H)X447.2(D)mm

(set with stand)

Weight (Net/Gross)

16.8/19.7 kg

Operating Environment

Temperature : 10-40°C/50-104°F

Relative Humidity : 8-80%

Storage Environment

Temperature : -20-45°C/-4-113°F

Relative Humidity : 5-90%

GENERAL INFORMATION

This color monitor automatically scans all horizontal frequencies from 30KHz to 69KHz, and all vertical

frequencies from 50Hz to 160Hz. This color monitor adopted the OSD (On Screen Display), it shows the sync

polarity and frequency and it provides that easily adjust control. This color monitor supports IBM PC, PC/XT,

PC/AT, personal System/2 (PS/2), Apple Macintosh, and compatible users crisp text and vivid color graphics

display when using the following graphics adapters : (VGA, 8514/A, Super VGA, VESA and XGA and Apple

Macintosh Video Card). And so, this color monitor has a maximum horizontal resolution of 1280 dots and a

maximum vertical resolution of 1024 lines for superior clarity of display.

By accepting analog signal inputs which level is zero to 0.7 Volts. This color monitor can display and unlimited

palette of colors depending on the graphics adapter and software being used.

Abbreviations

ADJ

Adjustment

AFC

Automatic Frequency Control

Cathode Ray Tube

Deflection

CRT

Def

D.Y

Deflection Yoke

FBT

Flyback Transformer

Horizontal Synchronization

Oscillator

H.SYNC

OSC

P.S.U

PWA

R.G.B

V.Sync

Power Supply Unit

Printed Circuit Board Wiring Assembly

Red, Green, Blue

Vertical Synchronization

PIN CONNECTOR

Signal

Red

Green

Blue

GND

GND - Red

GND - Green

GND - Blue

Reserved

GND - H.Sync

GND

Arrangement of 15-pin D-sub connector

Bi-directional Data (SDA)

Horizontal Sync

Vertical Sync (VCLK)

Data Clock (SCL)

CAUTIONS FOR ADJUSTMENT AND REPAIR

• Degaussing is always required when adjusting purity or convergence.

• The white balance adjustment has been done by a color analyzer in factory. The adjustment procedure,

described in the service manual is made by a visual check.

• Allow 20 minutes warm-up time for the display before checking or adjusting only electrical specification or

function.

• Reform the leadwire after any repair work.

Caution For Servicing

• In case of servicing or replacing CRT, high voltage sometimes remains in the anode of the CRT. Completely

discharge high voltage before servicing or replacing CRT to prevent a shock to the serviceman.

OPERATION & ADJUSTMENT

ADJUSTMENT KEY

Launch OSD(On-Screen Display) menus

Select the next function

Increase the value of any selected function

Decrease the value of any selected function

ADJUSTMENT PROCESS

BRIGHTNESS

50%

CONTRAST

50%

PINCUSHION

50%

TRAPEZOID

50%

COLOR TEMP.

9300 6550

RED GAIN

50%

_ZZ

RECALL

STATUS

H : +31.5KHZ

YES

V : +70.5 HZ

When you choose the icon

on the OSD window, you can exit the OSD screen.

OSD(On-Screen Display) Menu 1

Adjust the contrast of image, the difference between light and dark

CONTRAST

areas on the screen.

Range : 0-100%

50%

BRIGHTNESS

Adjust the brightness of the entire display.

Adjust the position of the display horizontally

(left or right).

H.POSITION

H.SIZE

Adjust the display width (horizontal size).

50%

V.POSITION

Adjust the position of the display vertically (up or down).

V.SIZE

Adjust the display height (vertical size).

50%

Degauss the display and restore image quality.

OSD(On-Screen Display) Menu 2

Adjust the left and right margins for more convex or more concave

margins.

• Image turns to

Adjust the trapezoid of the screen by moving the lines inward or outward.

TRAPEZOID

• Image turns to

50%

Adjust parallelogram when the screen is leaning left or right.

PARALLELOGRAM

50%

• Image turns to

Adjust the side balance when the sides of the screen are bowed towards

left or right.

PIN BALANCE

• Image turns to

50%

• Image turns to

Adjust the vertical picture moire cancellation.

• Image turns to

V. MOIRE

50%

Adjust the rotation when the screen is tilted left or right(Optional).

ROTATION

• Image turns to

OSD(On-Screen Display) Menu 3

Choose different preset color temperatures or set your own customized

color parameters.

Adjust the red gain.

RED GAIN

50%

GREEN GAIN

Adjust the green gain.

Adjust the blue gain.

Adjust the red bias.

Adjust the green bias.

Adjust the blue bias.

BLUE GAIN

RED BIAS

50%

GREEN BIAS

BLUE BIAS

50%

OSD(On-Screen Display) Menu 4

STATUS

Display horizontal & vertical frequency and polarity.

H : +31.5KHZ

V : +70.5 HZ

Reset the screen to the Factory Preset Display Settings.

YES : VESA DPMS operation.

NO : NO DPMS operation.

Select language for OSD.

Self Diagnosis

When the monitor doesn’t display, if you press any key, Self Diagnosis screen is displayed.

Self Diagnosis function checks if the status of the monitor is No Signal or Out of range.

No Signal screen is displayed when the D-Sub signal connector is not

connected or the status of the monitor is on DPMS mode.

Out of Range screen is displayed when the applied frequency is

under or over normal range.

Normal range

H : 30-69 KHz

V : 50-160 Hz

TROUBLESHOOTING HINTS

1. No Character

No Character

Are the

Contrast &

Brightness Controls

maximum

Change the Contrast &

Brightness control to

maximum

Yes

Is whole

screen bright?

Refer to

No Raster

Yes

Is CRT

Cathode (Rk, Gk, Bk)

signal level

Yes

Check the peripheral circuit

of CRT Board

Rk, Gk, Bk

About 45Vpp

normal?

Is the

output signal of the

(pin 21, 24, 26) pre-amp

(IC801, KA2500)

normal?

Check the video output

circuit and IC803 (pin 1, 3, 5)

and their ambient circuit

Yes

Is 12V DC line

normal?

Trouble in 12V DC line

of the Main PWB

Yes

Is clamping

pulse (pin 18 of IC801)

normal?

Check the clamping pulse

circuit

Yes

Is input signal

normal?

Check the signal cable

Yes

Trouble in IC801 and

its ambient circuit

2. No Raster

No Raster

Is Heater

Voltage (CRT PWB)

about 6V?

Is CRT

heater red-hot?

Trouble in

CRT

Yes

Trouble in

power supply

circuit

Turn the Brightness

& Contrast control

to set Maximum

Refer to trouble in

power supply unit.

Yes

Is whole

Trouble in power

supply circuit

screen bright?

Yes

Check

G1 voltage about

-40V?

Trouble in G1

line of Main PWB

Yes

Is CRT

G2 (screen) voltage

about 500V?

Trouble in FBT

Yes

Trouble in 80/

120V DC line of

power supply unit

Is 80V DC

line normal?

Refer to trouble

in P,S,U

Yes

Does

turning the Brightness

control counterclockwise

make screen

High Voltage

trouble in FBT

bright?

Yes

Trouble in FBT

3. A missing Color

One color is

missing

Is input signal

normal?

Check video signal

cable or video card.

0.7Vpp

Yes

Is the

output of pre-amp

(IC801, KA2500)

pin 21, 24, 26 all

normal?

Trouble in IC801 or its

ambient circuit

Yes

CRT

Is video

output IC803 waveform

normal?

Trouble in

Cathode (Rk, Gk, Bk)

is normal?

video output

circuit, IC803

or ambient

RK, GK, BK

About 40V p-p

Yes

Trouble in 80/120V DC

line

Each grid (G1, G2)

voltage normal?

Yes

Trouble in 80/120V DC

line

Replace CRT

4. Abnormal OSD Font

Abnormal OSD Font

* If menu key selected.

Is menu

key selected?

Is OSD Font

exist?

Is Heater

Voltage (CRT PWB)

about 6V?

Trouble in

Heater voltage

line.

Refer to trouble in P.S.U

Yes

One color is

missing

Troubie in

IC802 or its

ambient circuit

Yes

Is the

Trouble in IC802

and its ambient

circuit

output of IC802

(pin 13, 14, 15)

normal?

Yes

Refer to Missing Color

5. Horizontal Output Circuit

Trouble in Horizontal

output circuit

(No Raster

Trouble in B+ Booster Circuit

(Check the B+section of IC501,

Check Q603 and its ambient

circuit).

Is the

B+line voltage

over 45V?

Yes

Is the H-out

waveform of IC501

normal?

11V

Trouble in IC501

Yes

Is the Collector

wave form of

Q501 or Q502

normal?

10V

Trouble in Q501, Q502

Yes

Is the Collector

waveform of

Q503 normal?

Trouble in Q503 and its

ambient circuit.

66V

Yes

Trouble in Q504 and

its ambient circuit.

6. Unstable Picture

6-1. Horizontal

Unstable

picture

Is H.Sync

input pin of IC501

correct?

Check H.Sync Out of

Micom or its ambient

circuits.

Yes

Is the

pin 3 of IC501

5V?

Check the value of

C503, R502

Yes

Trouble in IC501

6-2. V.OSC/Deflection Circuit

Unstable or

Abnormal picture

Yes

Trouble in

± 13V DC line

power supply unit

correct?

Yes

the output

45Vp-p

V.DY

failure

waveform of IC401

(pin 6) normal?

Is the

output pulse

of IC501 (pin 23)

normal?

Trouble in IC401 or

its ambient circuit

Trouble in V.Sync line

or IC501 failure.

7. Focus

Monitor remains

unfocused

Check

Focus VR in

FBT

focus

Yes

acceptable?

Trouble in Focus

circuit (FBT)

7-1. Dynamic Focus

FVH FVV

* Check after adjusting the static focus

finely by VR in FBT

Focus is poor

PHILIPS

NEC

: 440V 180V

: 300V 120V

SAMSUNG : 300V 120V

waveform

Is the

1. Check the CRT socket

or connector wire

Yes

waveform of the

DF pin in FBT

correct?

FVH

2. Trouble in FBT or CRT

FVV

Is the

cathode voltage

of the D575

about 600V?

1. Check the waveform of

the pin 3 of FBT.

2. Check D575

Yes

Is the

base voltage of

the Q751 about

2.6V?

1. Check the 12V DC line.

2. Check Q751,D755

Yes

Is the

waveform of

the pin 10 in IC501

correct?

Trouble in IC501 or C520

waveform

4.5V

Yes

0.8V

Trouble in Q752, Q753, Q754,

D751, D752, D753, D754,

Q755, Q756

8. Convergence

Poor convergence

Yes

convergence

on the center area

bad?

Adjust static

convergence

Refer to

Adjustment

procedure of

convergence

Yes

Adjust D.Y

Location

convergence on the

fringe area bad?

9. Abnormal Picture

9-1. Horizontal Size

Abnormal

H.Size

When

the VR601 is

changed, is the H.size

changed?

Check pin 15 of IC501

and its ambient circuit

(D604, R605, R606, R607)

Yes

Is the

1.Check B+ section of TDA9109

and its ambient circuit.

2.Check Q601 and its ambient

circuit.

H.Size about 295mm

at VGAmode and Min. H.Size

in OSD Menu?

Yes

It isn't out of order.

9-2. Vertical Size

Abnormal

V.Size

Check the IC401

and its

ambient circuit

changeable the

DC voltage of

IC401 pin 1?

Yes

the 3.5Vdc of pin

23 of the IC501?

Yes

Trouble V.OSC/

Deflection Circuit

Check the IC501 and

its ambient circuit

Refer to V.OSC/Deflection circuit

10. High Voltage Circuit

Trouble in H.V circuit

(No Raster)

Trouble in power

supply circuit

B+(45V) line

voltage normal?

Yes

Is Q574

base waveform

normal?

Yes

Trouble in Q574 or FBT

Is Q571

collector waveform

normal?

Yes

Trouble in Q572, Q573

12V Line

Is Q501

emitter waveform

normal?

Trouble in Q571

Is IC501

pin 26 waveform

normal?

Trouble in Q501, Q502

Is IC501

pin 29 voltage

about 12V?

Trouble in power supply

Yes

Is the

input H.Sync

correct?

Yes

Trouble in IC501

ambient circuit.

Trouble in H.Sync

11. Side-Pincushion Circuit

Side-Pincusion distortion

is excessive or barrel

Select the

side-pincushion

icon on OSD menu,

and adjust acceptable

position.

Yes

O.K

Check IC501 or

their ambient circuit

(pin 14, 15, 16)

Is the pin 24

waveform of IC501

correct

Yes

Is the

waveform of IC501

pin 1, 2

Check IC501 or

it's ambient circuit.

Trouble in H.V Sync

12. Power Supply Unit (P.S.U)

Trouble in P.S.U

power switch

on?

Switch on

Yes

Check the power cord outlet

and diode D001, D002,

D003, D004

fuse F001

O.K?

Yes

Is the

voltage of IC001

pin 3 16V?

Replace R004

Replace C005

Yes

Trouble in D001, D002,

D003, D004, C004 and

TH001.

voltage of T001

pin 6 130V

(370V)?

Yes

Is the

waveform of IC001

pin 1correct?

Trouble in T001, IC001,

IC101, PH001 and D005 etc.

400Vpp (620Vpp)

Yes

Trouble in D102, D103 or

B+ Part

voltage of C103

45V DC?

Yes

Trouble in D101 or

Video Part

voltage of C101

80V DC?

Yes

Trouble in D108 or

Video Part

voltage of C113

120V DC?

Is voltage

Trouble in D104, IC102 or

horizontal Part.

of C104 13V DC?

Yes

Trouble in D105 or vertical

Part.

voltage of C105

-13V DC?

Yes

Is voltage

of C106

8.7V DC?

Trouble in D106 or Q103

Yes

P.S.U O.K

ALIGNMENT PROCEDURE

Standard Adjustment Conditions

1. Power source voltage : AC 120V, 60Hz./AC 220V, 50Hz

2. Aging : Take at least 20 minutes warm-up time.

3. Signals.

Video : Analog 0.7Vpp 75 terminal positive polarity

Synchronizing : TTL level Negative/Positive Separate/Composite

Deflection frequency

Horizontal Frequency : 30KHz - 69KHz

Vertical Frequency : 50Hz - 160Hz

Pre-Adjustment

1. High voltage Adjustment

Adjust 26 kvdc between Anode cap and ground at a cross hatch pattern of 31.5KHz by using VR551.

2. B+ Adjustment (H.min size)

(a) Receive a cross hatch pattern of 31.5KHz

(b) Set the H-Size control to the minimum.

Main Adjustment

1. Setting the Controls

Set the value of items as following.

Contrast : Max. (OSD value up to 100)

Brightness : Center (Set the OSD value to 50)

2. H.size, V.size, H.phase, V.position, Pincushion, Trapezoid

Perceive the cross hatch pattern of Factory preset mode.

H.Size, V.size, H.phase, V.position, Pincushion, Trapezoid are adjusted at each mode.

In Factory, Auto Alignment was done at each mode. Therefore, Factory preset mode has it’s own value

according to each control.

3. Focus

(a) Set brightness control to center and contrast control to MAX.

(b) Receive all “H” character pattern of 60KHz mode signal.

4. Geometric Distortion Adjustment.

(a) Receive the cross hatch pattern of VGA mode signal by using the signal generator.

(b) Pin balance, Parallelogram are adjusted the best geometric status.

5. White Balance Adjustment

(a) Receive a full white pattern of 60KHz mode.

(b) Select 9300°K on the OSD Menu.

(d) Adjust the FBT screen VR to get the screen luminosity to 1 Ft/L.

(e) Select the R, G, B Bias on the OSD menu and adjust the ADJUST +/– key to get the color coordinates in

X=0.281, Y=0.311

(f) If the screen luminosity is changed adjust the sub brightness control to get the 1 Ft/L screen luminosity.

(g) Set the brightness control to the center and contrast control to the maximum.

(h) Receive a full white pattern.

(i) Select the R, G, B gain on the OSD menu and adjust the ADJUST +/– key to get the color coordinates in

X=0.281±0.03, Y=0.311±0.03

(j) Adjust the sub contrast control to get the screen luminosity to 34 Ft/L/

(k) Select 6550°K on the OSD menu and set the bright control and contrast control to the maximum and receive

the all black pattern.

(l) Repeat (e),(f),(g),(h),(i),(j).

Just a difference from 9300°K mode is color coordinates.

Set color coordinates in X=0.313, Y=0.329

6. Static Convergence Adjustment

(a) Apply an magenta cross hatch pattern on display.

(b) Adjust the focus from the best over all focus on the display.

Also adjust the brightness to the desired condition.

(d) Horizontal red and blue lines are converged by varying the tabs together, keeping the angle between them

constant.

(e) Apply a white cross hatch pattern on display.

(f) Vertical green and magenta lines are converged by varying the the angle between the two tabs of the 6-pole

magnets.

(g) Horizontal green and magenta lines are converged by varying the tabs together, keeping the angle between

them constant.

(R.G.B)

VIDEO OUTPUT

LM2407T

VIDEO

PREAMP

OSD IC

KA2500

OSD

LSC4525P2

(R.G.B)

BIAS CONTROL

SCREEN,

FOCUS

H.VTG

H.V

SCL SDA

BIAS(R.G.B)

MICOM

SCL

EEPROM

24C08B

V.DRV AMP

KA2142

V.DY

SDA SCL

SDA

68HC705BD32

TILT IC

L272M

FBT

H.OSC.

CF1147DW2300

H.V SDA SCL

V.DRV

TDA9109

120V,80V,45V

12V, –12V

SMPS

TRANS

CONTROL

GND

H.VTG

B+

CONTROL

H.DRV

H.DY

FILTER

KA2S0880

KA7500B

B+

CONTROL

PCB LAYOUT

Main PCB Component Side

Main PCB Solder Side

Video PCB Component Side

Video PCB Solder Side

EXPLODED VIEW DIAGRAM

REPLACEMENT PARTS LIST

Important Safety Notice

Components identified with the International Symbol have special characteristics important for safety.

When replacing any components, use only manufacturer’s specified parts.

Abbreviation of Description

RESISTOR Description

Allowance

± 1%

± 5%

± 10%

± 20%

± 2%

Example:

Fig &

Index

Part No

Description

Cabron: 82J

Resistors

R101

RE-42820J

CAPACITOR Description

Allowance

± 0.25pF

± 0.5%

± 1pF

± 5%

± 10%

± 100% ~ 0%

± 80% ~ –

Example:

Fig &

Index

Part No

Description

Capacitors

CCXF1H104Z Ceramic 50V Z

CBSLH200J Ceramic 50V J

CCXB1H331K Ceramic 50V K

C102

C105

C402

CIRCUIT BOARD ELECTRICAL PARTS LIST

The components identified by mark

have special characteristics important for safety and x-ray radiation.

These should be replaced only with the types specified in the parts list.

LOC

10010

CT801

CT802

DG001

20010

CA801

CA802

CN001

C001

C004

C006

C103

C402

C406

C409

C519

C553

C578

DL001

D102

D103

D104

F001

PART-CODE

PCFMCAJ046

9979617018

9970710176

5MG0000062

PCMPM1J046

99707A0016

9970770019

9970700123

CL1UC3224M

CEYP2G221Z

CCYB3A103K

CEXF2A471V

CMXL2A474J

CEXF1C471V

CMXM2A224J

CMYH3D532J

CMXF2D824J

CMXM2A224J

DLT2462A2D

DS3L60----

PART-NAME

COVER FRONT AS

CDT

PART-DESC

CMC-710B

M41QAR361X124(E)

0.12*5*24+BL102NG=730

DG-710B

CRT GND AS

COIL DEGAUSSING

PCB MAIN MANUAL AS

CONN AS

CMC-710B

SMH250-10+1007#24#28=160

SMH250-07+1007#24=220

4.3+35404-9002+1015#18=50

0.22MF 1J(UCVSNDF/SV)+Q/O

400V SMH 220MF (25.4*40)

1KV B 0.01MF K

100V RSS 470MF 16*31.5

MEU 100V 0.47MF J

16V RSS 470MF (10X12.5)TP

100V 0.22MF J

CONN AS

C LINE ACROSS

C ELECTRO

C CERA

C ELECTRO

C MYLAR

C ELECTRO

C MYLAR

2KV BUP 5300PF J BULK

MPP 200V 0.82MF J

100V 0.22MF J

C MYLAR

LED

LT2462-A2-D51

S3L60

DIODE

DS3L60----

DIODE

S3L60

DS3L60----

DIODE

S3L60

5F3CB3122L

1KA2S0880-

1KA78R12--

1K1A7805P1

1DWM209T--

1KA2142---

FUSE CERA

IC POWER

IC REGULATOR

IC MICOM

SEMKO TL 3.15A 250V MF51

KA2S0880

IC001

IC102

IC103

IC201

IC401

IC501

IC801

L001

KA78R12

KIA7805PI

68HC705BD32

IC V-OUT

KA2142

1TDA9109--

1KA2500---

IC H.OSC

TDA9109

KA2500

5PDLF3055-

5MH0000051

5MC0000069

5MC0000068

5MC0000065

1TLP721GR-

9979500014

TKSC3502E-

FILTER LINE

COIL H-LINEARITY

COIL CHOKE

IC PHOTO COUPLER

RECEPTACLE

DLF-3055L

L501

TRL-195A

L502

33UH K BULK(14*16)

CH-85A

L571

L601

CH-85

PH001

P001

TLP721D4GR

YA03P/FILTER EMI

KSC3502E

Q503

LOC

D504

Q504

Q574

Q551

Q552

Q555

Q577

Q603

RL001

RL501

R754

SG900

SW001

S001

TH001

T001

PART-CODE

DDTV32F---

PART-NAME

DIODE

PART-DESC

DTV32F

T2SC5387--

TR H.OUT

2SC5387

TKSC5386--

T1RF630ATS

T2SK2799--

KSC5386

FET

IRF630A-TSTU

FET

IRF630A-TSTU

FET

IRF630A-TSTU

FET

2SK2799

T2SK2799--

FET

2SK2799

5SC0201103

5SC0101031

RS01Z104J-

4SG0D00104

5S50101Z01

9970800015

DTP8D15---

SW RELAY

R M-OXIDE FILM

SPARK GAP

SW TACT

HR-CR323 2C-1P DC12V

HR-703V DC12V 1C-1P

1W 100K OHM J (TAPPING)

S-23 1.5KV

KPT-1115VM 1C-1P

15P+2C/DDC=1.5M (IVY)

TP8D15

CABLE SIGNAL AS

THERMISTOR

TRANS SMPS

TRANS SYNC

TRANS DRIVE

FBT

5RM0000090

5RY0000002

5RD0000037

5RH0000105

5RF0000003

PCMPJ1J046

HCFK104ZCA

HCQK101JCA

HCFK104ZCA

HCQK360JCA

HCQK181JCA

HCFK104ZCA

HCBK223KCA

HCQK102JCA

HCFK333ZCA

HCFK224ZCA

HCQK102JCA

HCFK104ZCA

HCQK181JCA

HCFK104ZCA

DWT-44A1

T002

DST-603

T501

DDT-710B

T571

CF1147DW2300

T601

TRANS DUMMY

PCB SMD AS

C CHIP CERA

TDH-710B

30010

C015

C117

C119

C120

C122

C203

C204

C205

C206

C212

C403

C502

C503

C506

C507

C520

C532

C549

C581

CMC-710B

50V Y5V 0.1MF Z 2012

50V CH 100PF J 2012

50V Y5V 0.1MF Z 2012

50V CH 36PF J 2012

50V CH 180PF J 2012

50V Y5V 0.1MF Z 2012

50V X7R 0.022MF K 2012

50V CH 1000PF J 2012

Y5V 50V 0.033MF Z 2012

Y5V 50V 0.22MF Z 2012

50V CH 1000PF J 2012

50V Y5V 0.1MF Z 2012

50V CH 180PF J 2012

50V Y5V 0.1MF Z 2012

LOC

C802

C803

C812

C813

C814

C815

C832

C833

C862

C863

C878

C879

C881

C882

C883

C884

C885

R117

R205

R208

R209

R210

R216

R217

R218

R228

R234

R235

R238

R246

R247

R248

R252

R272

R284

R285

R286

R289

R502

R505

PART-CODE

HCFK104ZCA

HCQK101JCA

HCFK104ZCA

HCQK122JCA

HCFK103ZCA

HCQK220JCA

HRFT272JCA

HRFT472JCA

HRFT000JCA

HRFT472JCA

HRFT151JCA

HRFT201JCA

HRFT472JCA

HRFT222JCA

HRFT101JCA

HRFT472JCA

HRFT563JCA

HRFT912JCA

HRFT202JCA

HRFT682JCA

HRFT472JCA

PART-NAME

C CHIP CERA

R CHIP

PART-DESC

50V Y5V 0.1MF Z 2012

50V CH 100PF J 2012

50V Y5V 0.1MF Z 2012

50V CH 1200PF J 2012

50V Y5V 0.01MF Z 2012

50V CH 22PF J 2012

1/10 2.7K OHM J 2012

1/10 4.7K OHM J 2012

1/10 0 OHM J 2012

R CHIP

1/10 4.7K OHM J 2012

1/10 150 OHM J 2012

1/10 200 OHM J 2012

1/10 4.7K OHM J 2012

1/10 2.2K OHM J 2012

1/10 100 OHM J 2012

1/10 4.7K OHM J 2012

1/10 56K OHM J 2012

1/10 9.1K OHM J 2012

1/10 2K OHM J 2012

1/10 6.8K OHM J 2012

1/10 4.7K OHM J 2012

R CHIP

LOC

R506

R508

R513

R515

R516

R517

R531

R576

R581

R753

R801

R831

R853

R856

R861

R880

R885

R886

R887

R888

R889

R890

R936

R938

R942

40010

CW201

CW202

C002

C003

C008

C010

C101

C102

C104

C106

C113

C116

C522

C523

PART-CODE

HRFT272JCA

HRFT472JCA

HRFT153JCA

HRFT105JCA

HRFT122JCA

HRFT103JCA

HRFT223JCA

HRFT752JCA

HRFT621JCA

HRFT750JCA

HRFT472JCA

HRFT750JCA

HRFT101JCA

HRFT562JCA

HRFT105JCA

HRFT561JCA

HRFT182JCA

HRFT101JCA

HRFT472JCA

HRFT244JCA

HRFT243JCA

HRFT562JCA

PCMPJ0J046

485923282S

485923272S

CH1FDF222M

CEXF2A470V

CCXB3D102K

CEXF1E471V

CEXF1C471V

CEXF2C470V

CCXB3D222K

CMXF2G184J

CMXF2G154J

PART-NAME

R CHIP

PART-DESC

1/10 2.7K OHM J 2012

1/10 4.7K OHM J 2012

1/10 15K OHM J 2012

1/10 1M OHM J 2012

1/10 1.2K OHM J 2012

1/10 10K OHM J 2012

1/10 22K OHM J 2012

1/10 7.5K OHM J 2012

1/10 620 OHM J 2012

1/10 75 OHM J 2012

1/10 4.7K OHM J 2012

1/10 75 OHM J 2012

1/10 100 OHM J 2012

1/10 5.6K OHM J 2012

1/10 1M OHM J 2012

1/10 560 OHM J 2012

1/10 1.8K OHM J 2012

1/10 100 OHM J 2012

1/10 4.7K OHM J 2012

1/10 240K OHM J 2012

1/10 24K OHM J 2012

1/10 5.6K OHM J 2012

CMC-710B

R CHIP

PCB MAIN ODD SHAPE AS

CONN WAFER

C CERA AC

C ELECTRO

C CERA

5267-07A STICK TYPE

5267-06A STICK TYPE

HIKB AC400V 222M

100V RSS 47MF (10X16) TP

2KV B 1000PF K (TAPPING)

25V RSS 470MF (10X16) TP

16V RSS 470MF (10X12.5)TP

160V RSS 47MF (13X25) TP

HIKB 2KV 2200PF K

MPP 400V 0.18MF J

MPP 400V 0.15MF J

C ELECTRO

C CERA

C MYLAR

LOC

C531

C551

C552

C555

C574

C582

C584

C587

C588

C592

C605

C902

D001

D002

D003

D004

D005

D006

D101

D105

D106

D108

D403

D511

D512

D573

D575

D576

D577

D602

D603

D913

D914

IC203

IC502

IC802

IC804

PR001

P002

P003

PART-CODE

CEXF1C102V

CMXF2D204J

CMXF2D184J

CMXF2D334J

CMXH3C102J

CEXF2A221V

CMXF2D564J

CEXF2G220D

CEXF2C220V

CMXF2D474J

CMXF2D104J

D2A05-----

PART-NAME

C ELECTRO

C MYLAR

C ELECTRO

C MYLAR

C ELECTRO

C MYLAR

DIODE

PART-DESC

16V RSS 1000MF (10X20) TP

MPP 200V 0.2MF J (TP)

MPP 200V 0.18MF J (TP)

200V MPP 0.33MF J (TP)

1.6KV BUP 1000PF J

100V RSS 220MF (16X25) TP

MPP 200V 0.56MF J

400V KMG 22MF(12.5*25) TP

160V RSS 22MF (10X20) TP

MPP 200V 0.47MF J

MPP 200V 0.1MF J

2A05

D2A05-----

DIODE

2A05

D2A05-----

DIODE

2A05

D2A05-----

DIODE

2A05

D1N4937GP-

DHER107---

DRU1P-----

DIODE

1N4937GP (TAPPING)

HER107

DIODE

RU 1P (TAPPING)

HER107

DHER107---

DRU1P-----

DIODE

HER107

DIODE

RU 1P (TAPPING)

1N4002

D1N4002A--

DTVR1G----

DS2L60---R

DRU1P-----

DIODE

TVR1G TPA1

DIODE

TVR1G TPA1

DIODE

S2L60

DIODE

RU 1P (TAPPING)

TVR1G TPA1

DTVR1G----

DS2L60---R

DHER107---

1M24C08BN6

1KA7500B--

1LSC4525P2

1LM358N---

DECPAC140M

9977410800

DIODE

TVR1G TPA1

DIODE

TVR1G TPA1

DIODE

S2L60

DIODE

HER107

DIODE

HER107

IC EEPROM

M24C08BN6

KA7500B

IC OSD

LSC4525P2

IC OP AMP

POSISTOR

TERMINAL PIN

LM358N

ECPAC140M290

BSP1(SN) L=15MM

LOC

P401

P402

P403

P501

P502

P503

P504

R004

R006

R007

R107

R109

R110

R118

R407

R408

R518

R520

R529

R532

R554

R573

R587

R589

R603

R604

R631

R632

R633

R755

R756

R757

SW201

SW202

SW203

SW204

VR551

VR601

50010

C005

PART-CODE

9977410800

RS02Z513J-

RS01Z683J-

RS02Z392J-

RS02Z369J-

RS02Z399J-

RS02Z100J-

RS01Z109J-

RS02Z479J-

RS01Z101J-

RS01Z159J-

RS01Z101J-

RS01Z471J-

RS01Z470J-

RS02Z102J-

RW01Z308JN

RS02Z331J-

RW01Z308JN

RS02Z129J-

RS01Z104J-

5S50101Z01

RV6421503P

RV6121202P

PCMPJRJ046

CEXF1H101V

PART-NAME

TERMINAL PIN

R M-OXIDE FILM

R WIRE WOUND

R M-OXIDE FILM

R WIRE WOUND

R M-OXIDE FILM

SW TACT

PART-DESC

BSP1(SN) L=15MM

2W 51K OHM J

1W 68K OHM J (TAPPING)

2W 3.9K OHM J (TAPPING)

2W 3.6 OHM J (TAPPING)

2W 3.9 OHM J

2W 10 OHM J (TAPPING)

1W 1 OHM J (TAPPING)

2W 4.7 OHM J (TAPPING)

1W 100 OHM J (TAPPING)

1W 1.5 OHM J (TAPPING)

1W 100 OHM J (TAPPING)

1W 470 OHM J (TAPPING)

1W 47 OHM J (TAPPING)

2W 1K OHM J (TAPPING)

1W 0.30 OHM J NON-INDUCT

2W 330 OHM J TAPPING

1W 0.30 OHM J NON-INDUCT

2W 1.2 OHM J (TAPPING)

1W 100K OHM J (TAPPING)

KPT-1115VM 1C-1P

SW TACT

KPT-1115VM 1C-1P

SW TACT

KPT-1115VM 1C-1P

SW TACT

KPT-1115VM 1C-1P

R SEMI FIXED

CCT 065AT 50K OHM B TAP

CCT 063BT 2K OHM B TAP

CMC-710B

R SEMI FIXED

PCB MAIN RADIAL AS

C ELECTRO

50V RSS 100MF (8X11.5) TP

LOC

C011

C013

C014

C105

C107

C108

C109

C110

C111

C112

C114

C118

C202

C209

C210

C211

C266

C267

C271

C276

C277

C278

C279

C281

C401

C404

C405

C407

C408

C410

C411

C417

C504

C505

C509

C510

C511

C512

C513

C514

PART-CODE

CEXF1H109V

CCXF1H223Z

CEXF1C101V

CCXF1H223Z

CEXF1C101V

CEXF1C221V

CEXF1H100V

CMXM2A104J

CEXF1C101V

CCXB2H102K

CEXF1C101V

CCXB1H221K

CEXF1H100V

CMXM2A104J

CEXD1H220F

CEXF1H100V

CMX12A154J

CEXF1E470V

CEXF1C221V

CEXF1H101V

CCXB1H471K

CCXF1H104Z

CMXM2A562J

CCXF1H104Z

CMXM2A182J

CEXF1H479V

CCXF1H104Z

CEXF1E470V

CCXB1H102K

CEXF1H339V

CMXM2A392J

CEXF1H109V

PART-NAME

C ELECTRO

C CERA

PART-DESC

50V RSS 1MF (5X11) TP

50V F 0.022MF Z (TAPPING)

16V RSS 100MF (6.3X11) TP

50V F 0.022MF Z (TAPPING)

16V RSS 100MF (6.3X11) TP

16V RSS 220MF (8X11.5) TP

50V RSS 10MF (5X11) TP

100V 0.1MF J (TP)

C ELECTRO

C CERA

C ELECTRO

C MYLAR

C ELECTRO

C CERA

16V RSS 100MF (6.3X11) TP

500V B 1000PF K (TAPPING)

16V RSS 100MF (6.3X11) TP

50V B 220PF K (TAPPING)

50V RSS 10MF (5X11) TP

100V 0.1MF J (TP)

C ELECTRO

C CERA

C ELECTRO

C MYLAR

C ELECTRO

C MYLAR

50V RND 22MF (10*11.5)

50V RSS 10MF (5X11) TP

MEU 100V 0.15MF J(TP)

25V RSS 47MF (5X11) TP

16V RSS 220MF (8X11.5) TP

50V RSS 100MF (8X11.5) TP

50V B 470PF K (TAPPING)

50V F 0.1MF Z

C ELECTRO

C CERA

C MYLAR

100V 5600PF J (TP)

C CERA

50V F 0.1MF Z

C MYLAR

100V 1800PF J (TP)

C ELECTRO

C CERA

50V RSS 4.7MF (5X11) TP

50V F 0.1MF Z

C ELECTRO

C CERA

25V RSS 47MF (5X11) TP

50V B 1000PF K (TAPPING)

50V RSS 3.3MF (5X11) TP

100V 3900PF J (TP)

C ELECTRO

C MYLAR

C ELECTRO

50V RSS 1MF (5X11) TP

LOC

C515

C516

C517

C518

C525

C528

C533

C554

C556

C570

C572

C573

C577

C579

C580

C583

C586

C591

C593

C601

C603

C606

C751

C801

C804

C808

C811

C831

C861

C880

C901

C996

C998

F001A

F001B

IC101

IC202

Q102

Q103

Q104

PART-CODE

CMXM2A104J

CCXF1H104Z

CEXF2A100V

CMXM2A104J

CEXF1H100V

CEXF1H229V

CEXF1C101V

CCXB2H102K

CMXM2A104J

CEXF1H100V

CEXF1C221V

CEXF1C101V

CMXM2A562J

CEXF1C470V

CEXF1C101V

CCXB2H471K

CEXF1H100V

CMXM2A104J

CEXF1H339V

CEXF1H109V

CCXB2H102K

CMXM2A473J

CEXF1H100V

CEXF1C470V

CEXF1C220V

CEXF1H100V

CEXF1H101V

CMXM2A473J

CEXF1C220V

CEXF1H100V

9977410900

PART-NAME

C MYLAR

PART-DESC

100V 0.1MF J (TP)

C CERA

50V F 0.1MF Z

C ELECTRO

C MYLAR

100V RSS 10MF (6.3X11) TP

100V 0.1MF J (TP)

C ELECTRO

C CERA

50V RSS 10MF (5X11) TP

50V RSS 2.2MF (5X11) TP

16V RSS 100MF (6.3X11) TP

500V B 1000PF K (TAPPING)

100V 0.1MF J (TP)

C MYLAR

C ELECTRO

C MYLAR

50V RSS 10MF (5X11) TP

16V RSS 220MF (8X11.5) TP

16V RSS 100MF (6.3X11) TP

100V 5600PF J (TP)

C ELECTRO

C CERA

16V RSS 47MF (5X11) TP

16V RSS 100MF (6.3X11) TP

500V B 470PF K (TAPPING)

50V RSS 10MF (5X11) TP

100V 0.1MF J (TP)

C ELECTRO

C MYLAR

C ELECTRO

C CERA

50V RSS 3.3MF (5X11) TP

50V RSS 1MF (5X11) TP

500V B 1000PF K (TAPPING)

100V 0.047MF J (TP)

50V RSS 10MF (5X11) TP

16V RSS 47MF (5X11) TP

RSS 16V 22MF 5*11

C MYLAR

C ELECTRO

C MYLAR

50V RSS 10MF (5X11) TP

50V RSS 100MF (8X11.5) TP

100V 0.047MF J (TP)

RSS 16V 22MF 5*11

C ELECTRO

FUSE CLIP

IC SHUNT

IC VOTAGE DETECTOR

50V RSS 10MF (5X11) TP

BSP3-H T0.4 SN 5.2

KA431ZTA

9977410900

1KA431ZTA-

1KA7542---

KA7542

TKSD471ACY

TKTA1273Y-

KSD471ACY

KTA1273-Y

TZSR1006--

KSR1006 (AUTO)

LOC

Q201

Q202

Q203

Q204

Q501

Q502

Q516

Q517

Q525

Q553

Q556

Q557

Q558

Q571

Q572

Q573

Q575

Q601

Q602

Q751

Q752

Q753

Q754

Q755

Q756

Q871

Q901

Q902

Q903

Q904

Q905

X201

60010

A0001

B001

B002

B101

B175

B345

B381

PART-CODE

TKSD471ACY

TZSR1006--

TKSD471ACY

TKSA539CY-

TZSR1006--

TZTA1270Y-

TZSR1006--

T2N3904---

TKSD471ACY

TKSA539CY-

TKSD471ACY

TKSA539CY-

TKSD471ACY

TKSP45----

PART-NAME

PART-DESC

KSD471ACY

KSR1006 (AUTO)

KSD471ACY

KSA539CY

KSR1006 (AUTO)

KTA1270Y(AUTO)(562Y)

KSR1006 (AUTO)

2N3904

KSD471ACY

KSA539CY

KSD471ACY

KSA539CY

KSD471ACY

KSP45

TKSP92----

KSP92

TKSP92----

KSP92

TKSP45----

KSP45

TKSP45----

KSP45

TKSP45----

KSP45

TZSR1006--

TKSA910Y--

TZSC945CY-

TKSD471ACY

TKSA539CY-

TZSR1009--

5XJ6R0000E

PCMPJAJ046

9979800462

5PB13857--

KSR1006 (AUTO)

KSA910Y

KSC945C-Y (AUTO)

KSD471ACY

KSA539CY

KSR1009

CRYSTAL QUARTZ

PCB MAIN AXIAL AS

PCB MAIN

COIL BEAD

HC-49/S 6MHZ 22PF 30PPM

CMC-710B

T1.6*330*246

BI3857(AXIAL)

LOC

B881

C009

C201

C207

C208

C214

C246

C501

C524

C534

C548

C571

C575

C576

C752

C903

C941

C994

C995

C997

C999

DZ001

DZ008

DZ201

DZ202

DZ203

DZ401

DZ501

DZ571

DZ581

D012

D107

D206

D207

D209

D503

D525

D531

D532

D571

PART-CODE

5PB13857--

PART-NAME

COIL BEAD

C CERA

PART-DESC

BI3857(AXIAL)

CCZB1H102K

CCZB1H181K

CCZB1H221K

CCZF1H104Z

CCZB1H101K

CCZB1H471K

CCZF1H104Z

CCZB1H181K

CCZB1H471K

CCZB1H103K

CCZB1H102K

CCZF1H104Z

CCZB1H103K

CCZB1H102K

CCZF1H104Z

CCZB1H152K

CCZF1H104Z

DDZ4R3BM--

DDZ8R2BM--

DDZ5R1B---

DDZ15BM---

DZN4148---

50V B 1000PF K

50V B 180PF K

C CERA

50V B 220PF K

C CERA

50V B 220PF K

C CERA

50V HIKF 0.1MF Z

50V B 100PF K

C CERA

50V B 470PF K

C CERA

50V HIKF 0.1MF Z

50V B 180PF K

C CERA

50V B 470PF K

C CERA

HIKB 50V 0.01MF K AXIAL

50V B 1000PF K

50V HIKF 0.1MF Z

HIKB 50V 0.01MF K AXIAL

50V B 1000PF K

50V HIKF 0.1MF Z

50V B 1500PF K (AXIAL)

50V HIKF 0.1MF Z

DZ4.3BM

C CERA

DIODE ZENER

DIODE

DZ8.2BM

DZ-5.1B

DZ15BM

1N4148 AUTO 52MM

DZN4148---

DIODE

DZN4148---

DIODE

DZN4148---

DIODE

DZN4148---

DIODE

DZN4148---

DIODE

DZN4148---

DIODE

DZN4148---

DIODE

DZN4148---

DIODE

DZN4148---

DIODE

LOC

D572

D574

D578

D601

D604

D751

D752

D753

D754

D755

D756

D757

D801

D802

D831

D832

D861

D862

D901

D902

D912

J411

L881

R001

R010

R102

R105

R106

R108

R111

R112

R113

R115

R116

R201

R202

R203

R204

R207

R211

PART-CODE

DZN4148---

DFDH400---

DZN4148---

RD-AZ101J-

5CPZ101K02

RD-2Z105J-

RD-4Z101J-

RD-4Z201J-

RD-AZ222J-

RD-AZ511J-

RN-AZ2102F

RD-AZ102J-

RD-AZ153J-

RD-AZ102J-

RN-AZ1211F

RD-AZ472J-

RD-AZ333J-

RD-AZ472J-

RD-AZ911J-

RD-AZ122J-

RD-AZ472J-

RN-AZ1212F

PART-NAME

DIODE

PART-DESC

1N4148 AUTO 52MM

FDH400

DIODE

1N4148 AUTO 52MM

1/6 100 OHM J

DIODE

R CARBON FILM

COIL PEAKING

R CARBON FILM

R METAL FILM

R CARBON FILM

R METAL FILM

R CARBON FILM

R METAL FILM

100UH K (AXIAL 3.5MM)

1/2 1M OHM J

1/4 100 OHM J

1/4 200 OHM J

1/6 2.2K OHM J

1/6 510 OHM J

1/6 21K OHM F

1/6 1K OHM J

1/6 15K OHM J

1/6 1K OHM J

1/6 1.21K OHM F

1/6 4.7K OHM J

1/6 33K OHM J

1/6 4.7K OHM J

1/6 910 OHM J

1/6 1.2K OHM J

1/6 4.7K OHM J

1/6 12.1K OHM F

LOC

R212

R213

R214

R215

R226

R227

R229

R230

R231

R232

R241

R249

R250

R281

R282

R283

R293

R294

R295

R296

R401

R402

R403

R405

R406

R410

R411

R412

R501

R503

R504

R507

R509

R510

R511

R512

R514

R519

R521

PART-CODE

RN-AZ9091F

RN-AZ8252F

RN-AZ1502F

RN-AZ3012F

RD-AZ101J-

RD-AZ222J-

RD-AZ750J-

RD-AZ472J-

RD-AZ101J-

RD-AZ472J-

RD-AZ122J-

RD-AZ563J-

RD-AZ331J-

RD-AZ102J-

RD-AZ103J-

RN-AZ1002F

RN-AZ2211F

RN-4Z4000F

RN-AZ5601F

RD-2Z229J-

RD-2Z209J-

RD-AZ102J-

RD-AZ182J-

RD-AZ122J-

RD-AZ102J-

RD-AZ361J-

RD-AZ183J-

RD-AZ333J-

RD-AZ474J-

RD-AZ563J-

RD-AZ472J-

RD-4Z200J-

PART-NAME

R METAL FILM

PART-DESC

1/6 9.09K OHM F

1/6 82.5K OHM F

1/6 15K OHM F

1/6 30.1K OHM F

1/6 100 OHM J

1/6 2.2K OHM J

1/6 75 OHM J

R METAL FILM

R CARBON FILM

R METAL FILM

1/6 4.7K OHM J

1/6 100 OHM J

1/6 4.7K OHM J

1/6 1.2K OHM J

1/6 56K OHM J

1/6 330 OHM J

1/6 1K OHM J

1/6 10K OHM J

1/6 10K OHM F

1/6 2.21K OHM F

1/4W 400 OHM F

1/6 5.6K OHM F

1/2 2.2 OHM J

1/2 2 OHM J

R METAL FILM

R CARBON FILM

1/6 1K OHM J

1/6 1.8K OHM J

1/6 1.2K OHM J

1/6 1K OHM J

1/6 360 OHM J

1/6 18K OHM J

1/6 33K OHM J

1/6 470K OHM J

1/6 56K OHM J

1/6 4.7K OHM J

1/4 20 OHM J

LOC

R522

R524

R525

R526

R527

R533

R535

R541

R543

R545

R551

R552

R553

R556

R557

R558

R559

R560

R561

R562

R571

R572

R574

R575

R577

R578

R579

R580

R582

R583

R584

R585

R586

R591

R592

R594

R601

R602

R605

R606

PART-CODE

RD-AZ203J-

RD-4Z101J-

RD-4Z121J-

RD-AZ473J-

RD-4Z433J-

RD-AZ472J-

RD-AZ473J-

RD-AZ331J-

RD-4Z100J-

RD-AZ473J-

RD-AZ102J-

RD-AZ109J-

RD-AZ102J-

RD-AZ472J-

RD-4Z471J-

RD-AZ102J-

RD-2Z100J-

RD-4Z279J-

RD-4Z470J-

RD-4Z109J-

RD-AZ822J-

RD-AZ332J-

RD-AZ822J-

RD-AZ104J-

RD-AZ102J-

RD-AZ332J-

RD-4Z229J-

RN-AZ9092F

RD-AZ512J-

RD-AZ105J-

RD-2Z100J-

RD-AZ203J-

RD-AZ392J-

PART-NAME

PART-DESC

1/6 20K OHM J

R CARBON FILM

R METAL FILM

1/4 100 OHM J

1/4 120 OHM J

1/6 47K OHM J

1/4 43K OHM J

1/6 4.7K OHM J

1/6 47K OHM J

1/6 330 OHM J

1/4 10 OHM J

1/6 47K OHM J

1/6 1K OHM J

1/6 1 OHM J

1/6 1K OHM J

1/6 4.7K OHM J

1/4 470 OHM J

1/6 1K OHM J

1/2 10 OHM J

1/4 2.7 OHM J

1/4 47 OHM J

1/4 1 OHM J

1/6 8.2K OHM J

1/6 3.3K OHM J

1/6 8.2K OHM J

1/6 100K OHM J

1/6 1K OHM J

1/6 3.3K OHM J

1/4 2.2 OHM J

1/6 90.9K OHM F

1/6 5.1K OHM J

1/6 1M OHM J

1/2 10 OHM J

1/6 20K OHM J

1/6 3.9K OHM J

R CARBON FILM

LOC

R607

R611

R751

R752

R758

R759

R802

R803

R814

R832

R833

R844

R855

R862

R863

R874

R881

R902

R903

R904

R905

R906

R907

R908

R909

R910

R911

R916

R935

R937

R939

R940

R941

R943

R944

R945

R946

R947

R994

R997

PART-CODE

RD-AZ153J-

RD-AZ103J-

RD-AZ153J-

RD-AZ332J-

RD-2Z202J-

RD-AZ101J-

RD-AZ330J-

RD-AZ100J-

RD-AZ101J-

RD-AZ330J-

RD-AZ100J-

RD-AZ472J-

RD-AZ101J-

RD-AZ330J-

RD-AZ100J-

RD-AZ472J-

RD-AZ154J-

RD-AZ623J-

RD-AZ472J-

RD-AZ752J-

RD-AZ204J-

RD-AZ473J-

RD-AZ472J-

RD-AZ202J-

RD-AZ562J-

RD-AZ303J-

RD-AZ563J-

RD-AZ823J-

RD-AZ333J-

RD-AZ104J-

RD-AZ242J-

RD-AZ471J-

RD-AZ182J-

RD-AZ101J-

RD-AZ272J-

RD-AZ821J-

RD-AZ101J-

PART-NAME

PART-DESC

1/6 15K OHM J

R CARBON FILM

1/6 10K OHM J

1/6 15K OHM J

1/6 3.3K OHM J

1/2 2K OHM J

1/6 100 OHM J

1/6 33 OHM J

1/6 10 OHM J

1/6 100 OHM J

1/6 33 OHM J

1/6 10 OHM J

1/6 4.7K OHM J

1/6 100 OHM J

1/6 33 OHM J

1/6 10 OHM J

1/6 4.7K OHM J

1/6 150K OHM J

1/6 62K OHM J

1/6 4.7K OHM J

1/6 7.5K OHM J

1/6 200K OHM J

1/6 47K OHM J

1/6 4.7K OHM J

1/6 2K OHM J

1/6 5.6K OHM J

1/6 30K OHM J

1/6 56K OHM J

1/6 82K OHM J

1/6 33K OHM J

1/6 100K OHM J

1/6 2.4K OHM J

1/6 470 OHM J

1/6 1.8K OHM J

1/6 100 OHM J

1/6 2.7K OHM J

1/6 820 OHM J

1/6 100 OHM J

LOC

R998

R999

TP1

PART-CODE

RD-AZ471J-

RD-AZ433J-

85801052GY

PCCTSWJ046

9970710181

9979300008

9979220025

9979220022

CMXM2A224J

CCXE3D103P

CCXB3D471K

9970710179

1LM2407T--

PART-NAME

R CARBON FILM

WIRE COPPER

PCB CRT AS

CONN AS

PART-DESC

1/6 470 OHM J

1/6 43K OHM J

1/0.52 TIN COATING

CMC-710B

30020

CA804

CA805

CT801

CW801

CW802

C851

C891

C892

CA803

IC803

P11

1015#18+35068-9812=110

033 0 7700 44

CONN AS

SOCKET CRT

CONN WAFER

C MYLAR

SMAW250-10 (ANGLE)

SMAW250-07 (ANGLE)

100V 0.22MF J

C CERA

HIKE 2KV 0.01MF P

2KV B 470PF K (TAPPING)

1015#18+4.3PIEX2=160

LM2407T

C CERA

CONN AS

IC VIDEO OUTPUT

CONN WAFER

TERMINAL PIN

SPARK GAP

PCB CRT RADIAL AS

C ELECTRO

C MYLAR

4859242220

9977410800

4SG0D00104

PCCTJRJ046

CEXD1H109F

CMXM2A222J

CMXM2A333J

CCXF1H104Z

CEXF1E101V

CEXD1H109F

CMXM2A222J

CMXM2A333J

CEXF2A470V

CEXD1H109F

CMXM2A222J

CMXM2A333J

CCXB1H103K

CCXB1H102K

CEXF2A220V

TKSC1009Y-

TKSA910Y--

TKSC1009Y-

TKSA910Y--

TKSC1009Y-

TKSA910Y--

PCCTJAJ046

YFW800-02

SC801

SG891

40010

C805

C806

C807

C821

C822

C835

C836

C837

C852

C865

C866

C867

C893

C894

C895

Q805

Q806

Q835

Q836

Q865

Q866

50010

BSP1(SN) L=15MM

S-23 1.5KV

CMC-710B

50V RND 1MF (5X11) TP

100V 2200PF J (TP)

100V 0.033MF J (TP)

50V F 0.1MF Z

C MYLAR

C CERA

C ELECTRO

C MYLAR

25V RSS 100MF (6.3X11) TP

50V RND 1MF (5X11) TP

100V 2200PF J (TP)

100V 0.033MF J (TP)

100V RSS 47MF (10X16) TP

50V RND 1MF (5X11) TP

100V 2200PF J (TP)

100V 0.033MF J (TP)

50V B 0.01MF K

C MYLAR

C ELECTRO

C MYLAR

C CERA

50V B 1000PF K (TAPPING)

100V RSS 22MF (8*11.5)

KSC-1009-Y

C ELECTRO

KSA910Y

KSC-1009-Y

KSA910Y

KSC-1009-Y

KSA910Y

PCB CRT AXIAL AS

CMC-710B

LOC

B0001

B803

B805

B811

B812

B813

B814

B859

B863

B864

D803

D804

D805

D833

D834

D835

D863

D864

D865

L801

L831

L861

R804

R805

R807

R808

R809

R810

R811

R812

R822

R834

R835

R837

R838

R839

R840

R841

R842

R852

PART-CODE

9979800463

5PB13857--

DFDH400---

5CPZ568K02

RD-4Z271J-

RD-4Z101J-

RC-2Z470J-

RD-AZ133J-

RD-AZ683J-

RD-AZ224J-

RD-AZ154J-

RD-AZ474J-

RD-2Z104J-

RD-4Z271J-

RD-4Z101J-

RC-2Z470J-

RD-AZ133J-

RD-AZ683J-

RD-AZ224J-

RD-AZ154J-

RD-AZ474J-

RD-2Z104J-

PART-NAME

PCB VIDEO

PART-DESC

T1.6*244*246

COIL BEAD

BI3857(AXIAL)

FDH400

COIL BEAD

DIODE

FDH400

DIODE

FDH400

DIODE

FDH400

DIODE

FDH400

DIODE

FDH400

DIODE

FDH400

DIODE

FDH400

DIODE

FDH400

COIL PEAKING

R CARBON FILM

R CARBON COMP

R CARBON FILM

R CARBON COMP

R CARBON FILM

0.56UH K (AXIAL 3.5MM)

1/4 270 OHM J

1/4 100 OHM J

1/2 47 OHM J

1/6 13K OHM J

1/6 68K OHM J

1/6 220K OHM J

1/6 150K OHM J

1/6 470K OHM J

1/2 100K OHM J

1/4 270 OHM J

1/4 100 OHM J

1/2 47 OHM J

1/6 13K OHM J

1/6 68K OHM J

1/6 220K OHM J

1/6 150K OHM J

1/6 470K OHM J

1/2 100K OHM J

LOC

R864

R865

R867

R868

R869

R870

R871

R872

R882

R891

R892

R893

SG801

SG831

SG861

PART-CODE

RD-4Z271J-

RD-4Z101J-

RC-2Z470J-

RD-AZ133J-

RD-AZ683J-

RD-AZ224J-

RD-AZ154J-

RD-AZ474J-

RD-2Z104J-

RD-4Z562J-

RD-4Z564J-

RD-AZ103J-

DWSP201M--

PART-NAME

PART-DESC

1/4 270 OHM J

R CARBON FILM

R CARBON COMP

R CARBON FILM

SURGE ABSORBER

1/4 100 OHM J

1/2 47 OHM J

1/6 13K OHM J

1/6 68K OHM J

1/6 220K OHM J

1/6 150K OHM J

1/6 470K OHM J

1/2 100K OHM J

1/4 5.6K OHM J

1/4 560K OHM J

1/6 10K OHM J

WSP-201M

DAEWOO ELECTRONICS CO., LTD

686, AHYEON-DONG MAPOGU,

SEOUL, KOREA.

C.P.O. BOX 8003 SEOUL KOREA

TELEX: DWELEC K28177-8

CABLE: "DAEWOOELEC"

http://www.dwe.co.kr

PRINTED DATE: NOV.1998

HP Hewlett Packard HP Compaq 24IN LED MONITR LCD A9P21A8#ABA User Manual
GE 881 User Manual
Fisher Paykel CT655 User Manual
Electrolux E30GC74G User Manual
Black Box Computer Hardware VX HDV iP HDMI User Manual
Avaya B159 User Manual
AT T TL92370 User Manual
Asus M2A MVP User Manual
AOC 718Swag 1 User Manual
Advantech FPM 3150G User Manual