Dacor Convection Oven ERWD30 User Manual

Installation Instructions  
Warming Drawer  
Models:  
DWD30, ERWDEWD24, EWD27,  
EWD30, EWD27, IWD30, MRWD27,  
MRWD30DH30, MWDV27,  
MWDVDV30  
Part No. 102345 Rev. S  
Table of Contents  
Before You Begin... ........................................................... 1 Installation Instructions.................................................... 7  
Important Safety Instructions .......................................... 1  
General Safety Precautions............................................. 2  
Installation Specifications................................................ 3  
Verifying the Package Contents....................................... 3  
Installation Planning......................................................... 3  
Install Support Platform in Cabinet .................................. 6  
Electrical and Environmental Specifications .................... 6  
Remove the Drawer ........................................................ 7  
Installing the Chassis....................................................... 7  
Re-installing the Drawer................................................... 8  
Towel Rack Installation ................................................... 8  
Verify Warming Drawer Operation ................................... 9  
Installation Checklist ........................................................ 9  
Before You Begin...  
Important:  
Installer: In the interest of safety and to minimize problems, read these installation instructions completely and carefully  
before you begin the installation process. Leave these installation instructions with the customer.  
Customer: Keep these installation instructions for future reference and the locrical inspector’s use.  
If you have questions or problems with installation, contact  
your Dacor dealer or the Dacor Customer Service Team.  
For repairs to Dacor appliances under warranty call the  
Dacor Distinctive Service line. Whenever you call, have  
the complete model and serial number for your appliance  
available. The numbers are found on the product data label  
located on back of the drawer front.  
The data label also contains the product electrical  
requirements.  
Dacor Customer Service  
Phone: (800) 793-0093 (U.S.A. and Canada
Monday — Friday 6:00 a.m. to 5:00 p.m. Pa
Web site:  
Product data label  
on back for drawer  
front  
Dacor Distinctive Service (repaily)  
Phone: (877) 337-3226 (U.S.A
Monday — Friday 6:00 a.m. e  
Imant Safety Instructions  
Safety Symbols and Labels  
Important Information About  
Safety Instructions  
DANGER  
Immediate hazards that WILL result in severe personal  
injury or death.  
The Important Safety Instructions and warnings in  
these instructions are not meant to cover all possible  
problems and conditions that can occur. Use common  
sense and caution when installing, maintaining or  
operating this or any other appliance.  
WARNING  
Hazards or unsafe practices that COULD result in severe  
personal injury or death.  
Always contact the Dacor Customer Service Team  
about problems and conditions that you don’t  
understand.  
CAUtION  
Hazards or unsafe practices that COULD result in minor  
personal injury or property damage.  
1
Important Safety Instructions  
General Safety Precautions  
To reduce risk of fire, electric shock, serious injury or death when using your appliance, follow basic precautions, including  
the following:  
WARNING  
WARNING  
Clean the warming drawer thoroughly before  
Use this appliance only for its intended use as  
described in this manual. Use it only to warm food  
and heat plates and utensils. It is not designed for  
commercial, industrial or laboratory use.  
operating it for the first time.  
To reduce the risk of fire in the warming drawer, do  
not overcook food. Do not leave it unattended with  
paper, plastic or other combustible materials inside.  
Only model OWD24 is approved for use in outdoor  
installations and near water (bathrooms). Do not  
use, store or install warming drawer models other  
than OWD24 near water, for example, near sinks,  
swimming pools or in a wet basement.  
If materials inside the warming drawer should ignite,  
keep the drawer closed and shut off the power at the  
circuit breaker panel or fuse box.  
Exercise cautioopening the warming drawer.  
Let hot air ope before looking or reaching  
into the w
Model OWD24, when installed as a towel warmer,  
must be installed indoors and have the supplied wire  
rack installed in the drawer bottom according to these  
instructions.  
Use oen removing food and  
coong drawer. Wet pot holders  
cs.  
Do not install or operate a product that is  
damaged, has a damaged power cord or plug, or is  
malfunctioning in any manner. Return the appliance to  
the nearest authorized service facility for examination,  
repair or adjustment.  
e whole eggs, sealed containers  
ars in the drawer. They may explode  
causing injury.  
warming drawer is on in continuous mode  
ill remain on until turned off manually. Exercise  
ion when operating the unit in continuous mode.  
Make sure that the appliance has been properly  
installed and grounded by a qualified installer  
according to the accompanying installation  
instructions. Have the installer show you
of the electrical outlet so that you know
disconnect power to the appliance.  
Do not place more than 50 pounds in the drawer.  
Properly clean and maintain the unit regularly as  
instructed in the use and care manual. Clean only  
those parts listed, in the manner specified.  
Do not repair or replace any par
drawer unless specifically rec
literature accompanying it. ld be  
done by a qualified techni
Do not use abrasive scrubbers or abrasive/caustic  
cleaners or detergents on this appliance. They may  
permanently damage the finishes. Do not use aerosol  
cleaners, because they may be flammable or cause  
corrosion of metal parts.  
Use of accessory attachmentended by  
the appliance manufacturer may injuries.  
Before cleaning or performing any type of service,  
make sure that the power plug is disconnected from  
the electrical outlet and that the unit is cool.  
Make sure the warming drawer is used only by those  
individuals who are able to operate it properly.  
Do not tamper with the controls.  
DO NOT TOUCH ANY HOT SURFACES IN OR  
ON THE WARMING DRAWER DURING OR  
IMMEDIATELY AFTER USE. Use the handle instead.  
After use, make sure these surfaces have had  
sufficient time to cool before touching them. Heating  
elements may be hot, even though they are dark in  
color.  
Never allow anyone, including children to sit, stand  
or climb on any part of the appliance, including the  
drawer. Doing so may cause tipping, damage, serious  
injury or death.  
Do not leave children unattended in the area around  
the appliance. Do not allow children to operate it, play  
with the controls, pull on the handle or touch other  
parts. Do not store items of interest to children above  
the warming drawer. Children could be burned or  
injured while climbing on the appliance.  
To avoid the possibility of fire or burns, do not allow  
clothing, potholders, towels or rags to come into  
contact with any part of the warming drawer during  
and immediately after use. Do not wear loose or  
hanging apparel while using the appliance.  
2
Installation Specifications  
Verifying the Package Contents  
C
B
(3) mounting screws - PN 83569  
Wire rack with mounting hardware (OWD24 only)  
(1) PN 83619 (screw), (1) PN 83267 (clamp)  
Installation Planning  
Chassis  
E
A qualified technician must complete the installation of this built-  
in appliance. Proper installation is the customer's responsibility.  
Carefully check the location where the drawer is to be installed.  
The drawer should be placed for convenient access. Make  
certain that electrical power can be provided in the selected  
location. Install the warming drawer in wood cabinets only.  
5/16”  
(8 mm)  
Plan the installation so that all minimum clearances are met or  
exceeded. Dimensions shown provide minimum clearances,  
unless otherwise noted. Be certain that proper clearance is  
provided for the drawer when it is in the open position.  
r open  
F
The specified minimum cabinet depth and width must be  
provided. The cabinet depth and width must completely enclose  
the recessed portion of the drawer.  
Cabinet cutout dimensions must be used as indicated. All  
contact surfaces between the appliance and the cabin
be solid and level. The drawer support platform mus
with the bottom edge of the cabinet cutout.  
rall Dimensions - IWD/OWD Series  
top View  
Make certain that you have everything neces
proper installation before proceeding.  
40" (101.6 cm)  
3 prong  
120 Vac power cord  
Mounting hole,  
9 places  
A custom front panel is required for IW
series models and optional for OWD
An optional Epicure® style front p
is available for model OWD24
**  
**  
**  
G
D
Chassis without  
drawer installed  
** = OWD24 mounting holes  
A
Drawer Face Dimensions  
Chassis Dimensions  
(IWD/OWD Series)  
(IWD/OWD Series)  
(D)  
(E)  
(F)  
(G)  
(A) Dimension  
Drawer Face  
Width  
(C) Dimension  
Chassis Face  
Width  
(B) Dimension  
Chassis Width  
Dimension Dimension Dimension Dimension  
Drawer  
Face Height  
Model  
Chassis  
Depth  
Drawer  
Depth  
Chassis  
Height  
22 5/16” (56.7 cm) 22 1/4” (56.5 cm) 22 3/8” (56.8 cm)  
25 5/16” (64.3 cm) 25 1/4” (64.1 cm) 25 3/8” (64.5 cm)  
28 5/16” (71.9 cm) 28 1/4” (71.8 cm) 28 3/8” (72.1 cm)  
IWD24  
8 15/16”  
(22.7 cm)  
23 3/8”  
(59.4 cm)  
23 13/16”  
(60.5 cm)  
9 1/16”  
(23.0 cm)  
IWD27  
IWD30  
11 7/8”  
(30.2 cm)  
20”  
(50.8 cm)  
18”  
(45.7 cm)  
11 7/8”  
(30.2 cm)  
22 1/2” (57.1 cm) 22 1/2” (57.1 cm) 22 1/2” (57.1 cm)  
OWD24  
See following page for chassis dimensions for other models  
3
Installation Specifications  
(A) Drawer Face  
Width  
(B) Chassis Face  
Model  
(C) Chassis Width  
Width  
DWD30  
30” (76.2 cm)  
27” (68.6 cm)  
30” (76.2 cm)  
24” (61.0 cm)  
27” (68.6 cm)  
30” (76.2 cm)  
36” (91.4 cm)  
26 3/4” (67.9 cm)  
29 3/4” (75.6 cm)  
27” (68.6 cm)  
30” (76.2 cm)  
27” (68.6 cm)  
30” (76.2 cm)  
30” (76.2 cm)  
29 5/8” (75.2 cm)  
26 5/8” (67.6 cm)  
29 5/8” (75.2 cm)  
23 5/8” (60.0 cm)  
26 5/8” (67.6 cm)  
29 5/8” (75.2 cm)  
35 5/8” (90.5 cm)  
26 5/8” (67.6 cm)  
29 5/8” (75.2 cm)  
26 5/8” (67.6 cm)  
29 5/8” (75.2 cm)  
2(67.6 cm)  
.2 cm)  
m)  
28 1/4” (71.8 cm)  
25 1/4” (64.1 cm)  
28 1/4” (71.8 cm)  
22 1/4” (56.5 cm)  
25 1/4” (64.1 cm)  
28 1/4” (71.8 cm)  
34 1/4” (87.0 cm)  
25 1/4” (64.1 cm)  
28 1/4” (71.8 cm)  
25 1/4” (64.1 cm)  
28 1/4” (71.8 cm)  
25 1/4” (64.1 cm)  
28 1/4” (71.8 cm)  
28 1/4” (71.8 cm)  
10 1/8”  
(25.7 cm)  
ERWD27  
ERWD30  
EWD24  
EWD27  
EWD30  
EWD36  
A
MRWD27  
MRWD30  
MWDH27  
MWDH30  
MWDV27  
MWDV30  
RWDV30  
Drawer Face Dimensions  
(MWD series shown)  
B
C
Warmimensions  
See page 3 fes chassis dimensions  
ERWD  
EWD  
2”  
9 cm)  
3 7/16”  
(8.7 cm)  
23 3/8”  
(59.4 cm)  
Chassis  
1 1/8”  
(2.9 cm)  
1”  
(2.5 cm)  
MWDH, MWDV,  
RWDV  
3 1/4”  
MRWD30B  
(only)  
All other MRWD  
series  
1 7/16”  
1”  
(8.3 cm)  
(3.7 cm)  
(2.5 cm)  
1”  
(2.5 cm)  
13/16”  
(60.5 cm)  
Drawer open  
Handle Dimensions  
40” (101.6 cm)  
3-prong 120 Vac  
power cord  
Mounting  
hole 9 places  
9"  
(22.9 cm)  
Overall Dimensions  
top View  
1/2" (1.3 cm)  
(EWD series shown)  
10"  
(25.4 cm)  
Chassis without  
drawer inserted  
1/2" (1.3 cm)  
Chassis Dimensions  
4
Installation Specifications  
27"/30"/36" Dacor  
single wall oven  
3/4" min.*  
(1.9 cm)  
Warming  
drawer  
D
C
D
C
C
C
36" typ.  
(91.4 cm)  
Warming  
drawer  
120 Vac  
elect.  
D
120 Vac  
electrical  
outlet  
Warming  
drawer  
3/4" min.*  
(1.9 cm)  
Warming  
drawer  
120 Vac  
elect.  
A
B
1 1/2" (3.8 cm)  
Typical countertop  
Toe kick  
Cooktop  
3/4" min.*  
(1.9 cm)  
A
3/4” min.*  
(1.9 cm)  
Cutouts Dimensions  
Warming  
C
drawer  
NOtES:  
Models EWD36 and OWD24 cannot  
installed above or below another  
ing drawer (any type).  
36" typ.  
(91.4 cm)  
120 Vac  
electrical  
outlet  
A
B
OWD24 is not approved for  
llation above, below or adjacent  
a wall oven or a warming drawer,  
including the same model.  
(B) Min. Width to  
(A) Cutout Width Adjacent Doors/  
Drawers  
D) Min. Vertical Gap  
Between Cutouts  
Min. Cutout  
Depth  
Model  
DWD30  
28 1/2” (72.4 cm) 30 1/4” (76.8 c
)  
cm)  
23.2 cm)  
8” (23.2 cm)  
1/8” (23.2 cm)  
9 1/8” (23.2 cm)  
9 1/8” (23.2 cm)  
9 1/8” (23.2 cm)  
9 1/8” (23.2 cm)  
9 1/8” (23.2 cm)  
9 1/8” (23.2 cm)  
9 1/8” (23.2 cm)  
9 1/8” (23.2 cm)  
9 1/8” (23.2 cm)  
9 1/8” (23.2 cm)  
9 1/8” (23.2 cm)  
1 1/4” (3.2 cm)*  
1 1/4” (3.2 cm)*  
1 1/4” (3.2 cm)*  
1 1/4” (3.2 cm)*  
1 1/4” (3.2 cm)*  
1 1/4” (3.2 cm)*  
NA  
ERWD27 25 1/2” (64.8 cm) 27 1/4” (69.
ERWD30 28 1/2” (72.4 cm) 30 1/4” (
EWD24  
EWD27  
EWD30  
EWD36  
IWD24  
IWD27  
IWD30  
22 1/2” (57.2 cm) 24 1/
25 1/2” (64.8 cm) 2
28 1/2” (72.4 cm) 
34 1/2” (87.6 c)*  
22 1/2” (57.2
25 1/2” (64.8 cm)  
28 1/2” (72.4 cm)  
1 1/16” (2.7 cm)  
1 1/16” (2.7 cm)  
1 1/16” (2.7 cm)  
1 1/4” (3.2 cm)*  
1 1/4” (3.2 cm)*  
1 1/4” (3.2 cm)*  
1 1/4” (3.2 cm)*  
1 1/4” (3.2 cm)*  
1 1/4” (3.2 cm)*  
NA  
24” (61.0 cm)  
**  
MRWD27 25 1/2” (64.8 cm)  
27” (68.6 cm)*  
30” (76.2 cm)*  
MRWD30 28 1/2” (72.4 cm)  
MWDH27 25 1/2” (64.8 cm) 27 1/4” (69.2 cm)*  
MWDH30 28 1/2” (72.4 cm) 30 1/4” (76.8 cm)*  
MWDV27 25 1/2” (64.8 cm) 27 1/4” (69.2 cm)*  
MWDV30 28 1/2” (72.4 cm) 30 1/4” (76.8 cm)*  
OWD24  
22 5/8” (57.5 cm) 24 1/4” (61.6 cm)*** 11 15/16” (30.3 cm)  
9 1/8” (23.2 cm)  
20 1/8” (51.1 cm)  
24” (61.0 cm)  
RWDV30 28 1/2” (72.4 cm) 30 1/4” (76.8 cm)*  
1 1/4” (3.2 cm)*  
* Bare minimum spacing to allow for ventilation and avoid scraping on DWD, ERW, EWD, MRW, MWD and RWD models.  
** IWD models or OWD24 without the optional front panel kit: The chassis and drawer faceplate are smaller than the  
cutout. The custom front panel mounts to the drawer faceplate. The height and width of the custom front panel must  
exceed the cutout dimensions (A and C above) to cover the hole. Allow 1/4" minimum additional space on the top, bottom  
and sides from the custom front panel edge to prevent scraping against adjacent doors, drawers and the countertop.  
*** OWD24 with optional factory front panel kit only. Bare minimum spacing shown to avoid scraping. Gap above and  
below cutout is 3/4” minimum. See ** above for OWD24 with custom front panel.  
5
Installation Specifications  
Install Support Platform in  
Cabinet  
Chassis  
face  
Provide a platform (100 lb. load capacity) within the cabinet  
upon which the warming drawer will be supported. The  
platform must be installed level and straight. The top edge  
of the platform must be flush with the cutout at the front of  
the cabinet. There are no provisions to level the warming  
drawer after it has been installed. 3/4” (1.9 cm) thick  
plywood is recommended.  
Support  
platform  
NOtE: If the drawer is not installed in a level fashion, the  
drawer may slide open on its own or may not seal tightly,  
allowing heat to escape and resulting in poor warming  
drawer performance.  
Minimum aming temperature: 32°F (0°C).  
Electrical and Environmental  
Specifications  
The correcy and amperage must be  
supplieet from a grounded, single  
phated by a properly sized circuit  
buse.  
WARNING  
e, frequency and amperage ratings  
product data label. See page 1 for  
IMPORtANt: This appliance is equipped with a three  
prong grounding electric plug for protection against  
possible electric shock hazards. It must be plugged into  
a dedicated, grounded, electrical outlet. If only a two  
prong electrical outlet is available, it is the responsi
of the customer to have it replaced with a dedica
properly grounded three prong electrical outle
avoid an electric shock hazard, do not u
circumstances:  
Electrical Supply Requirements  
ac, 60 Hz, 15 Amp., dedicated circuit  
he warming drawer is supplied with a 40” (101.6 cm)  
power cord with a three prong grounded plug.  
total Connected Load 0.5 kW (4 Amp.)  
Cut or remove the third (ground)
The power supply requirements shown above are for  
reference only. If they do not agree with those listed  
on the product data label, use the requirements on the  
product data label.  
cord.  
Use an adapter plug.  
Use a power cord that is fra
It is the owner’s responsibility to ensure that the  
electrical outlet is installed by a qualified electrician.  
The electrical installation must comply with the latest  
revision of the National Electric Code ANSI/NFPA 70  
and local codes and ordinances.  
Immerse the power cord or plug or other  
liquid.  
Connect the appliance to an extension cord.  
NOtE: Use of a ground fault interrupter (GFI) is not  
recommended.  
If the electrical service provided does not meet the  
product specification, or does not conform to the NEC  
or local standards, do not proceed with the installation.  
Call a licensed electrician to correct the electrical  
service before proceeding.  
Be certain to locate the electrical outlet in an  
accessible location, so that the warming drawer may  
be easily unplugged in the event that service becomes  
necessary.  
Keep the electrical cord away from hot surfaces.  
Three prong plug  
Three prong  
grounded outlet  
6
Installation Instructions  
WARNING  
Installing the Chassis  
1. Grasp the warming drawer chassis on opposite  
sides and slide it partially into the cabinet opening.  
Temporarily support the chassis in place so that it will  
not tilt or fall.  
To avoid personal injury caused by the appliance  
falling forward when the drawer is opened, secure  
the chassis to the cabinet and support platform as  
instructed.  
Be certain that the power plug is disconnected from  
2. From an adjoining cabinet, reach in behind the drawer  
and pull the power cord until the plug is next to the  
electrical outlet. Do not plug in the power cord at this  
time.  
the electrical outlet before installation.  
Verify that the electrical supply matches the ratings  
found on the appliance data plate and the installation  
specifications before proceeding.  
3. After positioning the power cord and plug, slide the  
chassis completely into the cabinet until the front frame  
is positioned flush against the cabinet face.  
Remove the Drawer  
Remove the drawer from the appliance to allow access  
to the mounting holes during installation, and to reduce  
weight:  
4. Use the screws provided to secure the warming drawer  
chassis to the binet and support platform, insert them  
into the mooles and tighten into place. You may  
want to dprior to installing the mounting  
screw
1. Pull the drawer out to the fully open position.  
2. Push in on the locking tab on one side as you pull the  
drawer up.  
le, 9 places  
3. When the drawer comes loose from the slide, repeat  
the same process on the opposite side.  
4. Grip the drawer on both sides and pull it free.  
5. For safety, push both drawer slides into the drawe
opening.  
StEP 2: Push  
locking tab  
Mounting Hole Locations - ERW, EWD, IWD, MRW and  
MWD Series Models  
(IWD series models do not have a flange around  
the edge of the faceplate)  
Mounting hole, 4 places  
StEP 3: Pull up on  
front of drawer  
Mounting Hole Locations -  
OWD24  
Continued...  
Style varies, EWD27 shown  
7
Installation Instructions  
Re-installing the Drawer  
1. Pull the drawer slides all the way out of the drawer  
opening.  
Towel Rack Installation  
(OWD24 Only)  
Model OWD24 is designed so that it can be used as a  
towel warmer if desired. Other models are not equipped for  
this application. To use model OWD24 as a towel warmer,  
you must install the towel rack included with the unit in the  
bottom of the drawer.  
2. Gently lower the drawer between the extended slides  
until it is suspended by them.  
3. Slide the back of the drawer mounting brackets under  
the drawer mounting clips on the slides.  
4. Push one side of the drawer down onto its locking tab,  
until the tab locks into place.  
to install the towel rack:  
1. Open the drawer completely.  
5. Repeat the same process on the opposite side.  
2. Insert the towel rack into the drawer in the orientation  
shown below.  
6. Gently open and close the drawer to make sure that it  
is properly installed.  
StEP 3: Slide mounting  
bracket under clip on slide  
Clip on slide  
Slide  
3. Use the clamp and screw included with the rack to  
attach it to the back of the drawer face as shown  
below. There is a hole for the screw in the back of the  
face plate near the bottom.  
StEP 4: Push fr
of drawer down u
tabs lock into place  
8
Installation Instructions  
Warming Drawer Control Panel Layout  
Verify Warming Drawer  
Installation Checklist  
Operation  
WARNING  
1. Connect power plug to the electrical outlet.  
To ensure a d proper installation, the following  
checklist mpleted by the installer to  
ensure e installation has been  
over
2. Open the drawer and press the ON/OFF key on the  
control panel.  
3. Press the PROOF, LOW, MED and HIGH keys each  
in turn. When you press each key, the indicator directly  
above it should light. Leave the control panel set to  
HIGH.  
Pe responsibility of the  
portance of proper installation of  
wer cannot be overemphasized.  
4. Press the SELECt key. The 1 HOUR indicator should  
light. Press and release the SELECt key three (3)  
more times. Each time you press the SELECt ke
2 HOUR, 3 HOUR and 4 HOUR indicator light
come on. All lights should be on after press
SELECt key the third time.  
orm has been installed according to the  
s on page 6.  
rly grounded, dedicated, three prong electrical  
let has been installed for the appliance by a licensed  
electrician. See page 6.  
5. Press the "∞" key. The indicator li
should come on and the 1, 2 ,
lights should go out.  
The chassis has been properly fastened to the support  
platform and sides of the cabinet.  
See page 7.  
6. The warming drawer sho
You should begin to fe
drawer begin to heaten (10)  
minutes.  
The drawer has been properly installed. See page  
8.  
Model OWD24 for use as towel warmer: The towel rack  
has been installed. See page 8.  
7. When you have determihe heating  
element is working, press N/OFF key.  
Proper operation has been verified?  
If the warming drawer does not operate properly, follow  
these troubleshooting steps:  
The warranty has been activated on-line or the  
warranty card filled out completely and mailed?  
Verify that the circuit breaker for the electrical outlet  
is on and not tripped. Make sure the power plug is  
connected.  
Save these instructions for future reference.  
Repeat the above tests.  
If the appliance still does not work, contact Dacor  
Distinctive Service at (877) 337-3226. Do not attempt  
to repair the appliance yourself. Be sure to have the  
model and serial numbers available when you call. See  
page 1 for model/serial number location.  
Dacor is not responsible for the cost of correcting problems  
resulting from a faulty installation.  
9

HP Hewlett Packard Hewlett Packard Computer Monitor LE19F User Manual
HP Hewlett Packard Hewlett Packard Computer Hardware XA User Manual
Hanns G HN198DP User Manual
Franke Consumer Products Cooktop FPL 607 I XS 645H User Manual
Electrolux G 11602, G 21602 User Manual
Eizo RadiForce RX320 User Manual
CyberResearch PCIDIO 96H User Manual
Cisco Systems ASA5500XSSD120 User Manual
Atlantis Land WIRELESS ROUTER ADSL A02 RA210 W54 User Manual
Asus KCMA D8 User Manual