Cypress CY7C1018CV33 User Manual

CY7C1018CV33  
128K x 8 Static RAM  
device has an automatic power-down feature that significantly  
reduces power consumption when deselected.  
Features  
• Pin- and function-compatible with CY7C1018BV33  
• High speed  
Writing to the device is accomplished by taking Chip Enable  
(CE) and Write Enable (WE) inputs LOW. Data on the eight I/O  
pins (I/O through I/O ) is then written into the location  
— t = 10 ns  
0
7
AA  
specified on the address pins (A through A ).  
0
16  
• CMOS for optimum speed/power  
• Center power/ground pinout  
• Data retention at 2.0V  
• Automatic power-down when deselected  
• Easy memory expansion with CE and OE options  
Reading from the device is accomplished by taking Chip  
Enable (CE) and Output Enable (OE) LOW while forcing Write  
Enable (WE) HIGH. Under these conditions, the contents of  
the memory location specified by the address pins will appear  
on the I/O pins.  
• Available in Pb-free and non Pb-free 300-mil-wide  
32-pin SOJ  
The eight input/output pins (I/O through I/O ) are placed in a  
0
7
high-impedance state when the device is deselected (CE  
HIGH), the outputs are disabled (OE HIGH), or during a write  
operation (CE LOW, and WE LOW).  
Functional Description[1]  
The CY7C1018CV33 is a high-performance CMOS static  
RAM organized as 131,072 words by 8 bits. Easy memory  
expansion is provided by an active LOW Chip Enable (CE), an  
active LOW Output Enable (OE), and tri-state drivers. This  
The CY7C1018CV33 is available in a standard 300-mil-wide  
SOJ.  
Logic Block Diagram  
Pin Configurations  
SOJ  
Top View  
A
A
1
A
A
32  
1
0
16  
31  
30  
2
3
4
5
6
15  
A
A
14  
A
13  
2
A
3
29  
28  
I/O  
0
CE  
OE  
I/O  
I/O  
INPUT BUFFER  
27  
26  
I/O  
0
1
7
I/O  
1
A
0
I/O  
V
7
8
9
10  
11  
12  
13  
6
A
A
2
25  
24  
23  
22  
21  
1
V
CC  
SS  
I/O  
2
V
V
CC  
I/O  
SS  
A
3
I/O  
I/O  
2
3
5
4
A
I/O  
4
3
128K x 8  
ARRAY  
I/O  
A
A
5
A
WE  
A
4
12  
6
I/O  
4
A
A
11  
7
20  
19  
A
8
A
5
A
10  
14  
15  
16  
I/O  
5
A
6
A
9
A
8
18  
17  
A
7
I/O  
6
POWER  
DOWN  
COLUMN  
DECODER  
CE  
I/O  
7
WE  
OE  
Note:  
Cypress Semiconductor Corporation  
Document #: 38-05131 Rev. *D  
198 Champion Court  
San Jose, CA 95134-1709  
408-943-2600  
Revised August 3, 2006  
CY7C1018CV33  
AC Test Loads and Waveforms[4]  
ALL INPUT PULSES  
90%  
10%  
R 317Ω  
3.0V  
3.3V  
90%  
10%  
OUTPUT  
GND  
R2  
351Ω  
30 pF  
Fall Time: 1 V/ns  
Rise Time: 1 V/ns  
(a)  
(b)  
High-Z characteristics:  
R 317Ω  
3.3V  
OUTPUT  
R2  
351Ω  
5 pF  
(c)  
[5]  
Switching Characteristics Over the Operating Range  
-10  
-12  
-15  
Parameter  
Description  
Min.  
10  
3
Max.  
Min.  
12  
Max.  
Min.  
15  
3
Max.  
Unit  
Read Cycle  
t
t
t
t
t
t
t
t
t
t
t
Read Cycle Time  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
RC  
Address to Data Valid  
Data Hold from Address Change  
CE LOW to Data Valid  
OE LOW to Data Valid  
OE LOW to Low-Z  
10  
12  
15  
AA  
3
OHA  
ACE  
DOE  
LZOE  
HZOE  
LZCE  
HZCE  
10  
5
12  
6
15  
7
0
3
0
0
3
0
0
3
0
[6, 7]  
OE HIGH to High-Z  
5
5
6
6
7
7
[7]  
CE LOW to Low-Z  
[6, 7]  
CE HIGH to High-Z  
[8]  
CE LOW to Power-up  
PU  
[8]  
CE HIGH to Power-down  
10  
12  
15  
PD  
[9, 10]  
Write Cycle  
t
t
t
t
t
t
t
t
t
t
Write Cycle Time  
10  
8
12  
9
15  
10  
10  
0
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
WC  
CE LOW to Write End  
SCE  
AW  
Address Set-up to Write End  
Address Hold from Write End  
Address Set-up to Write Start  
WE Pulse Width  
8
9
0
0
HA  
0
0
0
SA  
7
8
10  
8
PWE  
SD  
Data Set-up to Write End  
Data Hold from Write End  
5
6
0
0
0
HD  
[7]  
WE HIGH to Low-Z  
3
3
3
LZWE  
HZWE  
[6, 7]  
WE LOW to High-Z  
5
6
7
Notes:  
4. AC characteristics (except High-Z) for all speeds are tested using the Thèvenin load shown in Figure (a). High-Z characteristics are tested for all speeds using  
the test load shown in Figure (c).  
5. Test conditions assume signal transition time of 3 ns or less, timing reference levels of 1.5V, input pulse levels of 0 to 3.0V.  
6.  
t
, t  
, and t  
are specified with a load capacitance of 5 pF as in (d) of AC Test Loads. Transition is measured ± 500 mV from steady-state voltage.  
HZOE HZCE  
HZWE  
7. At any given temperature and voltage condition, t  
is less than t  
, t  
is less than t  
, and t  
is less than t  
for any given device.  
HZCE  
LZCE HZOE  
LZOE  
HZWE  
LZWE  
8. This parameter is guaranteed by design and is not tested.  
9. The internal Write time of the memory is defined by the overlap of CELOW and WE LOW. CE and WE must be LOW to initiate a Write, and the transition of any of these  
signals can terminate the Write. The input data set-up and hold timing should be referenced to the leading edge of the signal that terminates the Write.  
10. The minimum Write cycle time for Write Cycle No. 3 (WE controlled, OE LOW) is the sum of t  
and t  
.
HZWE  
SD  
Document #: 38-05131 Rev. *D  
Page 3 of 7  
CY7C1018CV33  
Switching Waveforms  
[11, 12]  
Read Cycle No. 1  
t
RC  
ADDRESS  
t
AA  
t
OHA  
DATA OUT  
PREVIOUS DATA VALID  
DATA VALID  
[12, 13]  
Read Cycle No. 2 (OE Controlled)  
ADDRESS  
t
RC  
CE  
OE  
t
ACE  
t
HZOE  
t
DOE  
t
HZCE  
t
LZOE  
HIGH  
IMPEDANCE  
HIGH IMPEDANCE  
DATA OUT  
DATA VALID  
t
LZCE  
t
PD  
ICC  
t
PU  
V
CC  
50%  
50%  
SUPPLY  
CURRENT  
ISB  
[14, 15]  
Write Cycle No. 1 (CE Controlled)  
t
WC  
ADDRESS  
CE  
t
SCE  
t
SA  
t
SCE  
t
t
HA  
AW  
t
PWE  
WE  
t
t
HD  
SD  
DATA I/O  
DATA VALID  
Notes:  
11. Device is continuously selected. OE, CE = V .  
IL  
12. WE is HIGH for Read cycle.  
13. Address valid prior to or coincident with CE transition LOW.  
14. Data I/O is high impedance if OE = V  
.
IH  
15. If CE goes HIGH simultaneously with WE going HIGH, the output remains in a high-impedance state.  
Document #: 38-05131 Rev. *D  
Page 4 of 7  
CY7C1018CV33  
Switching Waveforms (continued)  
[14, 15]  
Write Cycle No. 2 (WE Controlled, OE HIGH During Write)  
t
WC  
ADDRESS  
t
SCE  
CE  
t
t
HA  
AW  
t
t
PWE  
SA  
WE  
OE  
t
t
SD  
HD  
DATA VALID  
DATA I/O  
IN  
NOTE 16  
t
HZOE  
[10, 15]  
Write Cycle No. 3 (WE Controlled, OE LOW)  
t
WC  
ADDRESS  
CE  
t
SCE  
t
t
HA  
AW  
t
SA  
t
PWE  
WE  
t
t
HD  
SD  
NOTE 16  
DATA I/O  
DATA VALID  
t
t
LZWE  
HZWE  
Truth Table  
CE  
H
L
OE  
WE  
X
I/O –I/O  
Mode  
Power  
0
7
X
L
High-Z  
Power-down  
Read  
Standby (I  
)
SB  
H
Data Out  
Data In  
High-Z  
Active (I  
Active (I  
Active (I  
)
CC  
L
X
H
L
Write  
)
CC  
L
H
Selected, Outputs Disabled  
)
CC  
Note:  
16. During this period the I/Os are in the output state and input signals should not be applied.  
Document #: 38-05131 Rev. *D  
Page 5 of 7  
CY7C1018CV33  
Ordering Information  
Speed  
(ns)  
Package  
Diagram  
Operating  
Range  
Ordering Code  
Package Type  
10  
CY7C1018CV33-10VC  
CY7C1018CV33-12VC  
CY7C1018CV33-12VXI  
CY7C1018CV33-15VXC  
51-85041 32-lead 300-mil Molded SOJ  
32-lead 300-mil Molded SOJ  
Commercial  
Commercial  
Industrial  
12  
32-lead 300-mil Molded SOJ (Pb-Free)  
15  
32-lead 300-mil Molded SOJ (Pb-Free)  
Commercial  
Package Diagram  
32-lead (300-mil) Molded SOJ (51-85041)  
51-85041-*A  
All product and company names mentioned in this document are the trademarks of their respective holders.  
Document #: 38-05131 Rev. *D  
Page 6 of 7  
© Cypress Semiconductor Corporation, 2006. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use  
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be  
used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its  
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress  
products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.  
CY7C1018CV33  
Document History Page  
Document Title: CY7C1018CV33 128K x 8 Static RAM  
Document Number: 38-05131  
Issue  
Date  
Orig. of  
Change  
REV.  
**  
ECN NO.  
109426  
113432  
115046  
116476  
493543  
Description of Change  
12/14/01  
04/10/02  
05/30/02  
09/16/02  
See ECN  
HGK  
NSL  
HGK  
CEA  
NXR  
New Data Sheet  
AC Test Loads split based on speed  
and I modified  
*A  
*B  
I
CC  
SB1  
*C  
Add applications foot note on data sheet, pg 1  
*D  
Added Industrial Operating Range  
Removed 8 ns speed bin from Product offering  
Changed the description of I from Input Load Current to  
IX  
Input Leakage Current in DC Electrical Characteristics table  
Removed I parameter from DC Electrical Characteristics table  
OS  
Updated the Ordering Information Table  
Document #: 38-05131 Rev. *D  
Page 7 of 7  

Geemarc Jupiter 4 User Manual
GE 28031EE1 User Manual
Garland SGM 100D1 User Manual
Electrolux Air O Convect AOS102GCD1 User Manual
Dukane P42A User Manual
Dell SE198WFP User Manual
Crosley Radio Crosley Sultan CR93 User Manual
Cisco Systems Computer Hardware 1240AG User Manual
Addonics Technologies AD2MS6GPX8 E User Manual
Aastra Telecom BE 3872 User Manual