Contents
1. Before Use................................................... 3
2. Features ...................................................... 3
3. Names of the Buttons.................................. 4
4. Operations................................................... 4
5. Connections................................................. 7
6. Installation ................................................... 8
7. Troubleshooting........................................... 9
8. Specifications .............................................. 9
This unit has been tested and found to
installation.
comply with the limits for a Class B digital If this unit does cause harmful
device, pursuant to Part 15 of the FCC
Rules.
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user
is encouraged to consult the dealer or an
experienced radio/TV technician for help.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This unit generates, uses, and can
radiate radio frequency energy, and, if not
installed and used in accordance with the
instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
„ INFORMATION FOR USERS:
CHANGES OR MODIFICATIONS TO THIS
PRODUCT NOT APPROVED BY THE
MANUFACTURER WILL VOID THE
WARRANTY AND WILL VIOLATE FCC
APPROVAL.
2
1. Before Use
Warning
• Do Not Back Up Vehicle While Relying Only on the Monitor Image
• Use Slow Speeds When Backing Up
• The rear-view monitor image has the same right-left inversion as your vehicle’s
rearview mirrors. Depending on the vehicle, the field and angle of view may differ.
„ Precautions (when you use the monitor)
z Do not touch the LCD panel.
z Use the product at the temperature range of -10°C ~ 60°C.
z Screen may be a little dark when the product is operated in low temperature areas.
Screen will show normal luminosity after a few minutes.
z Do not disassemble and modify the product in any way.
This may cause fire and/or electric shock.
z When you install the product in a car and watch monitor, the car engine should be
running as there might occur excessive discharge of the car battery.
z Any liquid leaking into product may cause malfunction.
„ Precautions (when you use the product in a car)
z The driver should not use the product while he/she is driving.
z Be cautious of humidity and shock when you use the product in a car.
z Cover the product when exposed to direct rays of the sun for a long period of
time.
(You should keep the product at a temperature range of -20°C ~ 70°C.)
2. Features
z Application of 5.6" TFT LCD with high resolution and low reflection
z All functions are displayed on screen (OSD function)
z 7 Language Display Selection
(ENGLISH-DEUTSCH-ITALIANO-FRANÇAIS-ESPAñON-
z Free voltage (From DC12V to DC24V)
z Dimmer selection function
-
)
z Picture quality control (PWM control)
z Camera input (2 system)/Work together with back gear/turn signal
3
3. Names of the Buttons
[POWER]
[MODE]
[MENU]
[UP]
[DOWN]
STAND BY LED
4. Operations
1
2
POWER
(1) Press [POWER] button to on the power.
(STAND BY state is OFF)
(2) Press [POWER] button again to off the
power.
ON
OFF
(STAND BY state is ON)
MODE (Camera Selection)
„ It is a function to change CAMERA (CAM1/CAM2).
(1) Press [MODE] button.
(2) CAM1 or CAM2 appears on the screen
and it disappears after 5 seconds.
CAM1
CAM1
CAM2
Note: In the mirror mode, the character is
inverted.
4
3
MENU
„ It is a function to select MAIN MENU (SETUP, PICTURE CAMERA)
(1) Press [MENU] button to select MAIN MENU, changed color in red when it is selected.
•
Every time the button is pressed, the setting changes.
SETUP
PICTURE
CAMERA
(2) Press [MODE] button to select SUB MENU, changed color in red when it is selected.
Every time the button is pressed, the setting changes.
•
z SETUP
z PICTURE
CONTRAST
BRIGHTNESS
COLOR
50
70
50
50
DIMMER
LANGUAGE
ENGLISH
0
DIRECTION
RESET
TINT
SUB MENU
z CAMERA
CAM1
CAM2
NORMAL
NORMAL
SET UP (SUB MENU)
(3) Press [UP]/[DOWN] button to change Settings.
z DIMMER
–
z LANGUAGE
ENGLISH
–
–
–
ITALIANO
–
FRANÇAIS
–
–
DEUTSCH
ESPAñON
5
z DIRECTION (Inverted upside down)
R E S E T
1 8 0
D I R E C T I O N
L A N G U A G E
D I M M E R
E N G L I S H
DIMMER
LANGUAGE
DIRECTION
RESET
ENGLISH
0
z RESET X
A factory default reset will clear all of OSD information
PICTURE (SUB MENU)
(3) Press [UP]/[DOWN] button to change Settings.
z CONTRAST
z BRIGHTNESS
z COLOR
CONTRAST
BRIGHTNESS
COLOR
70
40
40
40
CONTRAST
BRIGHTNESS
COLOR
40
70
40
40
CONTRAST
BRIGHTNESS
COLOR
40
40
70
40
TINT
TINT
TINT
z TINT
CONTRAST
BRIGHTNESS
COLOR
40
40
40
50
TINT
CAMERA (SUB MENU)
(3) Press [UP]/[DOWN] button to change Settings.
z In the mirror mode, the screen is inverted laterally.
CAM1
CAM2
NORMAL
NORMAL
6
5. Connections
CAMERA1
*1
(Sold Separately)
CAMERA2
*1
*3
*3
(Sold Separately)
GREEN
BLACK
CAMERA1
CAMERA2
(CAMERA2) (CAMERA1)
*2
*2
*1
*2
Use a Clarion camera.
A relay cable, sold separately, is required
for connecting the camera.
Use tape to keep the connection between
the monitor cable and the camera relay
cable secure.
RED
POWER
DC12V~24V
BLACK
GROUND
*3
BLACK (CAMERA-1, priority)
GREEN (CAMERA-2)
Standby + (for rear-view)
Connect this cable to “+” of back gear lamp.
Standby + (for side-view)
Connect this cable to “+” of turn signal lamp.
7
6. Installation
1. Choose a location where you install the Monitor. Clean the place for the Stand with cleanser
and remove the Protective Tape. And then attach it exactly where you want.
2. Fasten the Monitor with Tapping Screw.
3. Adjust angle of Stand and install Monitor.
4. Connect each connecting cable as in the product installation reference.
Cable Guidance
Fix Knob
(Bracket)
Tapping Screw
Stand Base
Safeguard tape
Control Knob
(Angle)
„Monitor Cable Connection
* Installed on the ceiling
* Normal Installation
8
7. Troubleshooting
Problem
Cause
Measure
Is camera connected Check the wiring to the camera and the
No image is displayed.
properly?
camera connection.
Check the wiring.
Is power cable
connected properly?
Power does not turn on.
Color is washed-out.
Replace with a fuse of the same amperage
(2A).
Is a fuse blown out?
Operating
environment is
inappropriate.
Temperature in the car is below 0°C or over
60°C. Check to see that the temperature in
the car is appropriate (around 25°C).
8. Specifications
SPECIFICATION
ITEM
NTSC
PAL
SCREEN SIZE
NUMBER OF PIXELS
DOT PITCH
5.6 INCH (14.22cm)
320(W) x 3(RGB) x 234(H)
0.118(W) x 0.362(H) mm
2
PANEL
BRIGHTNESS
DISPLAY AREA
CONTRAST RATIO
VIEW ANGLE (H/U/D)
VOLTAGE
350 cd/m
113.28(W) x 84.7(H) mm
300:1
65deg / 45deg / 65deg
DC 12V - 24V
POWER SUPPLY
CURRENT
550mA (DC 12V, MONITOR SET ONLY)
DC 12V - 24V
REAR INPUT POWER
INPUT SYSTEM
AUTO (NTSC/PAL)
HORIZONTAL
VERTICAL
15.734 KHz
60Hz
15.625 KHz
50Hz
FREQUENCY
OSD DISPLAY
7 LANGUAGE
USER CONTROLS
POWER, MODE, MENU, UP, DOWN
-10°C ~ + 60°C
OPERATING TEMPERATURE
STORAGE TEMPERATURE
DIMENSION (W x H x D)
WEIGHT
-20°C ~ + 70°C
163(W) x 112(H) x 30(D)
0.3Kg
MONITOR CABLE ASS’Y·····································1
STAND ASS’Y·······················································1
ACCESSORIES
Caution: The design and specifications of this product in order to improve its quality may be changed without notice.
9
|