Cannon 50cm Free Standing Gas Cooker C50GCIW User Manual

The Art of Cooking  
Instructions for Installation and Use  
50cm Free Standing Gas Cooker  
Langdale  
C50GLB  
C50GLK  
C50GLW  
C50GLS  
C50GLX  
C50LCIK  
C50LCIW  
C50GCIK  
C50GCIW  
To the Installer  
Before installation fill in the product details on the back cover this book.  
The information can be found on the rating plate.  
To the User  
You must read the instructions prior to installing and using the appliance and  
then retain them for future reference.  
Introduction  
Your new appliance is guaranteed* and will give lasting service. This guarantee is only applicable if the appliance  
has been installed in accordance with the installation instructions detailed in this booklet.  
To help make best use of your cooking equipment, please read this booklet carefully.  
The cooker is designed specifically for domestic use and responsibility will not be accepted for use in any other  
installation.  
When the cooker is first used an odour may be emitted,  
this will cease after a period of use.  
When first using the cooker ensure that the room is well ventilated (e.g. open a window or use an extractor fan) and  
that persons who may be sensitive to the odour avoid any fumes. It is suggested that any pets be removed from the  
room until the smell has ceased. This odour is due to temporary finish on oven liners and elements and also any  
moisture absorbed by the insulation.  
* The guarantee is subject to the provisions that the appliance:  
(a)  
(b)  
Has been used solely in accordance with the Users Instruction Book.  
Has been properly connected to a suitable supply voltage as stated on the  
rating plate attached to this equipment.  
(c)  
(d)  
Has not been subjected to misuse or accident or been modified or repaired by  
any person other than the authorised employee or agent.  
Has been correctly installed.  
1
This appliance is intended for nonprofessional use within the home.  
2 These instructions are only for those countries whose symbols appear in the booklet and on the serial no.plate  
of the appliance.  
3 This owner’s manual is for a class 1 appliance (insulated) or class 2, subclass 1 appliances (installed  
between two cabinets.  
Keep the appliance clean, as a build up of grease or fat from  
cooking can cause a fire.  
3
Installation  
The appliance must only be installed by a competent person. In the UK, CORGI registered installers undertake  
to work to safe and satisfactory standards.  
Before moving your cooker check that it is cool, and switch off at the cooker control unit. Movement of your cooker is  
most easily achieved by lifting the front as follows:  
Open the grill door sufficiently to allow a comfortable grip on the underside front edge of the oven roof, avoiding any  
grill elements.  
Note: Take care in moving the cooker as it is heavy. Take care to ensure that any floor covering is not damaged.  
(FIG. C)  
Splashplate optional, apply to Parts Department (see Back Cover for contact number.)  
The following instructions should be read by a qualified technician to ensure that the appliance is installed,  
regulated and technically serviced correctly in compliance with current regulations.  
Important: remember to unplug the appliance from the mains before regulating the appliance or  
carrying out any maintenance work.  
Positioning  
Important: this unit may be installed and used only in permanently ventilated rooms according to the British  
Standards Codes Of Practice:B.S.6172/B.S.5440, Par.2 and B.S.6891 Current Editions.The following requirements  
must be observed:  
a) The cooker should not be installed in a bed sitting room with a volume of less than 20m3. If it is installed in a  
room of volume less than 5m3 an air vent of effective area of 110cm2 is required, if it is installed in a room of  
volume between 5m3 and 10m3 a supplementary airvent area of 50cm2 is required, if the volume exceeds 11m3  
no airvent is required. However, if the room has a door or a window which opens directly to the outside no air  
vent is required even when the volume is between 5m3 and 11m3.  
b) During prolonged use of the appliance you may consider it necessary to open a window to the outside to  
improve ventilation.  
c) If there are other fuel burning appliances in the same room, B.S.5440 Part 2 Current Edition, should, be  
consulted to determine the requisite air vent requirements.  
Installation of the cooker  
For a correct installation of the cooker the following precautions must be followed:  
The height of the cooker can be adjusted by means of adjustable feet in the plinth (900mm - 930mm). Adjust the feet by  
tilting the cooker from the side. Then install the product into position.  
NOTE: This appliance must not be fitted on a platform.  
The cooker is designed to fit between kitchen cabinets spaced 500mm apart. The space either side need only be sufficient  
to allow withdrawal of the cooker for servicing. It can be used with cabinets one side or both as well as in a corner setting.  
It can also be used free-standing.  
Adjacent side walls which project above hob level, must not be nearer to the cooker than 150mm or 65mm (Fig. A) and should  
be protected by heat resistant material. Any overhanging surface or cooker hood should not be nearer than 750mm. (Fig.A)  
a) The cooker may be located in a kitchen, a kitchen/diner or bed sitting room, but not in a bathroom or  
shower room.  
b) The hoods must be installed according to the requirements in the hood handbook.  
c) The wall in contact with the back of the cooker must be of flameproof material.  
d) The cooker is fitted with a safety chain that must be attached to a hook, secured to the wall behind the  
appliance.  
Note: some models can have their gas connection inverted.It is important to make sure the safety chain  
is always situated on the side which corresponds to the hose holder (Fig. B).  
Tall cupboard on the right hand  
side of 50cm gas cooker  
Tall cupboard on the left hand  
side of 50cm gas cooker  
Moving the Cooker  
150 mm min  
400 mm min  
65 mm min  
400 mm min  
500 mm min  
500 mm min  
Fig. A  
Fig. B  
Fig. C  
4
Gas connection  
The cooker should be connected to the gas-supply by a corgi registered installer. During installation of this  
product it is essential to fit an approved gas tap to isolate the supply from the appliance for the convenience  
of any subsequent removal or servicing. Connection of the appliance to the gas mains or liquid gas must be  
carried out according to the prescribed regulation in force, and only after it is ascertained that it is adaptable  
to the type of gas to be used. If not, follow the instructions indicated in the paragraph headed “Adaptation to  
different gas types”. On some models the gas supply can be connected on the left or on the right, as  
necessary; to change the connection, reverse the position of the hose holder with that of the cap and  
replace the gasket (supplied with the appliance). In the case of connection to liquid gas, by tank, use  
pressure regulators that conform to the regulation in force. The gas supply must be connected to the left of  
the appliance. Be sure that the hose does not pass through the rear of the cooker touching hot parts.  
HOT PARTS  
Important: make sure the supply pressure conforms with the values shown in the table entitled “Caracteristics of  
the burners and nozzles”. When the cooker is installed between cabinets (recessed), the gas connection  
must be effected by an approved flexible hose with bayonet fitting (BS 669 Current Edition).The gas inlet  
for the cookers is a threaded G 1/2 gas female fitting.  
Connecting the gas supply  
To make the connection, a flexible hose should be used corresponding to the current gas regulations which are:  
the hose must never be at any point in its lenght in contact with the “hot” parts of the cooker;  
the hose must never be longer than 1,5 metre;  
the hose must not be subject to any tension or torsional stress and it must not have any excessively narrow  
curves or bottlenecks;  
the hose must be easy to inspect along its entire length to check its condition;  
the hose must always be in good condition, never attempt to repair.  
Important: the installation must comply with gas safety (installation and use) regulations 1984. In all cases for the  
above, by low, a qualified, corgi approved engineer must be called for installation.  
Disposing of the appliance  
When disposing of the appliance please remove the plug by cutting the mains cable as close as possible to the  
plug body and dispose of it as described above.  
Adapting the cooker to different types of gas  
In order to adapt the cooker to a different type of gas with respect to the gas for which it was produced  
(indicated on the label attached to the lid), follow these steps:  
a) replace the hose holder mounted on the appliance with that supplied in the bag of “cooker accessories”.  
b) Replacing the burner nozzles on the hob:  
remove the grids and slide the burners from their housings;  
unscrew the nozzles using a 7 mm socket spanner, and replace them with nozzles for the new type of  
gas (see table 1 “Burner and nozzle characteristics”).  
replace all the components by repeating the steps in reverse order.  
5
c) Minimum regulation of the hob burners:  
turn the tap to minimum;  
remove the knob and adjust the regulation screw, which is positioned in or next to the tap pin, until the  
flame is small but steady.  
N.B.: in the case of liquid gas, the regulation screw must be screwed in to the bottom.  
check that the flame does not turn off when you turn the tap quickly from high to low.  
d) Regulating the primary air of the burners:  
The primary air of the burners requires no regulation.  
Adapting to different types of gas  
In order to adapt the oven to a different type of gas with respect to the gas for which it was manufactured  
(indicated on the label), follow these simple steps:  
a) Replacing the oven burner nozzle  
open the oven door fully  
pull out the sliding oven bottom  
Z
V
V
Pry the fixing tab “V” and remove the oven burner  
Unscrew the oven burner nozzle using the socket spanner for the nozzles “Z”, or a 7 mm socket spanner,  
and replace it with a nozzle suited to the new type of gas (see Table 1).  
Take particular care handling the spark plug wires and the thermocouple pipes.  
Replace all the parts, following the steps described above in the reverse order.  
b) Minimum regulation of the gas oven burner with thermostat:  
light the burner as described in the paragraph “the oven knob” of the instruction booklet.  
turn the knob to Max for about 10 minutes and then turn the knob to the Min setting;  
remove the knob;  
regulate the screw positioned outside the thermostat pin until the flame is small but steady.  
N.B.: in the case of liquid gas, the regulation screw must be screwed in to the bottom.  
6
check that the burner does not turn off when you turn the knob from Max to Min and and when you open  
and close the oven door quickly.  
Adapting the gas grill to different types of gas  
Replacing the nozzle of the grill burner:  
remove the screw and then slide out the grill burner “V” (see Fig. E);  
unscrew the grill burner nozzle using the special socket spanner for the nozzles (see Fig. F) or better still  
a 7 mm socket spanner; replace the nozzle with a nozzle for the new type of gas (see table 1).  
V
I
Fig. E  
Fig. F  
Important  
On completion of the operation, replace the old rating sticker with one indicating the new type of gas used.  
This sticker is available from our Service Centres.  
Note  
Should the pressure of the gas used be different (or vary) from the recommended pressure, it is necessary to  
fit a suitable pressure regulator onto the inlet pipe in compliance with current National Regulations relative to  
“regulators for channelled gas”.  
7
Electrial connection  
Power supply voltage and frequency:220-240V a.c.50 Hz.  
Note: the supply cable must be positioned so that it never reaches at any point a temperature 50°C higher than the  
room temperature.The cable must be routed away from the rear vents.Should you require it, you may use a longer  
cable, however, you must ensure that the cable supplied with the appliance is replaced by one of the same  
specifications in accordance with current standards and legislation.  
Your appliance is supplied with a 13 amp fused plug that can be plugged into a 13 amp socket for immediate use.  
Before using the appliance please read the instructions below.  
WARNING -THIS APPLIANCE MUST BE EARTHED.  
THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN.  
Replacing the fuse:  
When replacing a faulty fuse, a 13 amp ASTA approved fuse to BS 1362 should always be used, and the fuse  
cover re-fitted. If the fuse cover is lost, the plug must not be used until a replacement is obtained.  
Replacement fuse covers:  
If a replacement fuse cover is fitted, it must be of the correct colour as indicated by the coloured marking or the  
colour that is embossed in words on the base of the plug. Replacements can be obtained directly from your  
nearest Service Depot.  
Removing the plug:  
If your appliance has a non-rewireable moulded plug and you should wish to remove it to add a cable extension or  
to re-route the mains cable through partitions, units etc., please ensure that either:  
the plug is replaced by a fused 13 amp re-wireable plug bearing the BSI mark of approval.  
or:  
the mains cable is wired directly into a 13 amp cable outlet, controlled by a switch, (in compliance with BS  
5733) which is accessible without moving the appliance.  
Please note: for appliances with a rating greater than 13 amp (eg: electric hob, double ovens and freestanding  
electric cookers etc.) the mains cable must be wired into a cooker output point with a rating of 45 amp. In this case  
the cable is not supplied.  
Disposing of the plug:  
Ensure that before disposing of the plug itself, you make the pins unusable so that it cannot be accidentally  
inserted into a socket. Instructions for connecting cable to an alternative plug:  
Important: the wires in the mains lead are coloured in accordance with the following code:  
Green &Yellow  
Blue  
Brown  
- Earth  
- Neutral  
- Live  
If the colours of the wires in the mains lead do not correspond with the coloured markings identifying the terminals  
in your plug, proceed as follows:  
Connect Green &Yellow wire to terminal marked “Eor 6or coloured Green or Green &Yellow.  
Connect Brown wire to terminal markedLor coloured Red.  
Connect Blue wire to terminal marked “N” or coloured Black.  
If a 13 amp plug (BS 1363) is used it must be fitted with a 13 amp fuse. A 15 amp plug must be protected by a 15  
amp fuse, either in the plug or adaptor or at the distribution board. If you are in any doubt about the electrical supply  
to your machine, consult a qualified electrician before use.  
How to connect an alternative plug:  
The wires in this mains lead are coloured in accordance with the following code:  
BLUE  
BROWN  
NEUTRAL(N”)  
LIVE” (“L”)  
GREEN &  
YELLOW  
GREEN ANDYELLOW  
EARTH” (“E”)  
13 amp fuse  
BROWN  
BLUE  
CROSS-BAR  
CORD GRIP  
8
Burner and Nozzle Specifications  
Table 1  
Liquid Gas  
Diameter Thermal Thermal By-Pass Nozzle  
Natural Gas  
Burner  
Flow*  
g/h  
Thermal Nozzle Flow*  
Power  
kW  
Power  
kW  
1/100 1/100  
Power  
kW  
1/100  
l/h  
(p.c.s.*) (p.c.s.*)  
(p.c.s.*)  
(mm)  
Nominal Reduced (mm)  
(mm)  
80  
***  
**  
Reduced (mm)  
Fast  
(Large)(R)  
100 94  
2,60  
1,90  
1,00  
0,70  
0,40  
0,40  
41  
30  
30  
189  
138  
73  
186  
0,70  
0,40  
0,40  
118  
104  
76  
248  
181  
95  
Semi Fast  
(Medium)(S)  
75 69  
51 46  
70  
52  
136  
71  
Auxiliary  
(Small)(A)  
Oven  
Grill  
-
-
2,60  
2,50  
0,60  
1,30  
36  
63  
71  
80  
189  
182  
186  
179  
0,60  
1,30  
115  
122  
248  
238  
Nominal (mbar)  
Minimum (mbar)  
Maximum (mbar)  
28-30 37  
20  
17  
25  
Supply  
Pressures  
20  
35  
25  
45  
*
At 15°C and 1013 mbar- dry gas  
**  
***  
Propane  
Butane  
Natural  
P.C.S. = 50,37 MJ/Kg  
P.C.S. = 49,47 MJ/Kg  
P.C.S. = 37,78 MJ/m3  
S
A
S
R
C50GLB  
C50GLK  
C50GLW  
C50GLS  
C50GLX  
C50LCIK  
C50LCIW  
C50GCIK  
C50GCIW  
9
Safety Information  
When used properly your appliance is completely safe but as with any electrical product there are certain  
precautions that must be observed.  
PLEASE READ THE PRECAUTIONS BELOW BEFORE USING YOUR APPLIANCE.  
Always  
l
l
l
l
l
l
l
Remove all packing from inside the oven and grill compartments before switching on for the first time.  
Understand the controls prior to using the appliance.  
Keep children away from the appliance when grilling as the surfaces will get extremely hot during and after use.  
Turn controls off when you have finished cooking and when not in use.  
Stand back when opening an oven door to allow any build up of steam or heat to disperse.  
Use dry good quality oven gloves when removing items from the oven/grill.  
Place pans centrally over the hotplate making sure handles are kept away from the edge of the hob and cannot  
become heated by other hotplate/pans.  
l
l
l
l
l
l
l
l
l
l
l
Take care to avoid heat/steam burns when operating the controls.  
Turn off the electricity supply at the wall switch before cleaning and allow the appliance to cool.  
Make sure the shelves are in the correct position before switching on the oven.  
Keep the oven and grill doors closed when the appliance is not in use.  
Take care when removing items from the grill when the lower oven is on as the contents will be hot.  
Keep the appliance clean, as a build up of grease or fat from cooking can cause a fire.  
Follow the basic principles of food handling and hygiene to prevent the possibility of bacterial growth.  
Keep ventilation slots clear of obstructions.  
Refer servicing to a qualified appliance service engineer.  
Take care to avoid touching heating elements inside the oven, as during use the oven becomes hot.  
Before operating the product, remove all plastic film from the sides of the appliance.  
1 0  
Safety Information  
Never  
l
Never line the interior of the oven with foil as this may cause the appliance to overheat.  
l
Never leave children unsupervised where a cooking appliance is installed as all surfaces will be hot during  
and after its use.  
l
l
l
l
l
l
l
Do not allow children or persons who are not familiar with the appliance to use it, without supervision.  
Never allow anyone to sit or stand on any part of the appliance.  
Never store items above the appliance that children may attempt to reach.  
Never leave anything on the hob surface when unattended and not in use.  
Never remove the oven shelves whilst the oven is hot.  
Never heat up unopened food containers as pressure can build up causing the container to burst.  
Never store chemicals/food stuffs, pressurised container in or on the appliance, or in cabinets immediately  
above or next to the appliance.  
l
l
Never place flammable or plastic items on or near the hob.  
Never fill a deep fat frying pan more than 1/3 full of oil, or use a lid.  
DO NOT LEAVE UNATTENDED WHILE COOKING.  
l
l
l
l
l
l
Never operate the grill with the grill door closed as this will cause the appliance to overheat.  
Never use the appliance as a room heater.  
Never use the grill to warm plates.  
Never dry any items on either the hob or oven doors.  
Never install the appliance next to curtains or other soft furnishings.  
Never use steam cleaners.  
SAFETY ADVICE IN CASE OF A CHIP-PAN FIRE  
In the event of a chip pan fire or any other pan fire.  
1. TURN OFF THE COOKER APPLIANCE AT THE WALL SWITCH.  
2. COVER THE PAN WITH A FIRE BLANKET OR DAMP CLOTH, this will smother the flames and extinguish the  
fire.  
3. LEAVE THE PAN TO COOL FOR AT LEAST 60 MINUTES BEFORE MOVING IT. Injuries are often caused by  
picking up a hot pan and rushing outside with it.  
NEVER USE A FIRE EXTINGUISHER TO PUT OUT A PAN FIRE as the force  
of the extinguisher is likely to tip the pan over.  
Never use water to extinguish oil or fat fires.  
1 1  
Features  
GLASS COVER  
HOB VENTILATION SLOTS  
1900W  
2600W  
1900W  
1000W  
CONTROL  
PANEL  
GRILL/MEAT PAN  
WITH REMOVABLE  
HANDLE AND WIRE  
FOOD SUPPORT  
GRILL  
GRILL DOOR  
REMOVABLE  
INNER GLASS  
DOOR  
MAIN OVEN  
WIREWORK  
SHELF  
SUPPORTS  
MODEL & SERIAL  
NUMBER  
OVEN ROD  
SHELVES  
1 2  
Control Panel  
RIGHT  
FRONT  
BURNER  
RIGHT  
REAR  
BURNER  
LEFT  
REAR  
BURNER  
LEFT  
FRONT  
BURNER  
ELECTRONIC  
TIMER  
MAIN  
OVEN  
GRILL  
To light a specific burner push the corresponding knob all the way in and turn it counter-clockwise to  
Electronic  
Ignition  
for the Gas Hob*  
maximum keeping it pressed down until the burner lights.  
Important: Should the burner flames accidentally go out, turn off the control knob and wait at least 1  
minute before trying to relight.  
The position of the gas burner controlled by each one of the knobs is shown by a solid ring •. To light  
one of the burners, hold a lighted match or lighter near the burner and, at the same time, press down  
Control Knobs  
for the gas  
burners  
and turn the corresponding knob counter clockwise to the maximum setting. Each burner can be  
operated at its maximum, minimum or intermediate power. Shown on the knob are the different symbols  
for off • (the knob is on this setting when the symbol corresponds with the reference mark on the  
control panel), for maximum and minimum . To obtain these settings, turn the knob counter  
clockwise with respect to the off position. To turn off the burner, turn the knob clockwise until it stops  
(corresponding again with the • symbol).  
Models with Hob  
Gas Burner Safety  
Devices to Prevent  
Leaks *  
These models can be identified by the presence of the device itself.  
Important: Since the hob burners are equipped with a safety device, you must hold the control knob in  
for about 3 seconds after the burner has been lighted to allow the gas to pass until the safety  
thermocouple has heated.  
The main oven has a ‘SLOWCOOK’ setting specially designed to reduce energy usage. Full details of  
this can be found in the Slow cooking section of this book.  
Slow cooking  
‘SLOWCOOK’  
The electronic timer displays the time and the timer function with countdown.  
Electronic  
timer*  
* (only available on certain models)  
1 3  
Use of Hotplates  
Practical Advice on Using the Burners  
To use the burners as efficiently as possible, some basic guidelines should be followed:  
Use cookware that is the right size for each burner (see table) in order to prevent the flame from spreading  
beyond the bottom of the cookware.  
Only use cookware with flat bottoms.  
As soon as the boiling point is reached, turn the knob to the lowest setting.  
Always use lids with pots and pans.  
Burner  
ø Cookware diameter (cm)  
Fast (R)  
20 - 22  
16 - 20  
10 - 14  
Semi Fast (S)  
Auxiliary (A)  
N.B.: On models equipped with a reduction grid, the grid should only be used with the auxiliary burner when cookware  
with a diameter of less than 12 cm is used.  
1. To light a specific burner push the corresponding knob all the way in and turn it counter-clockwise to  
maximum keeping it pressed down until the burner lights.  
2. Turn the control knob anti-clockwise to the desired setting. Only turn the control knob between the large  
flame symbol and the small flame symbol for adjusting the setting.  
3. To turn off, turn the control knob fully clockwise to the symbol O.  
DO NOT use the hotplate unless all pan supports are in position.  
DO NOT use mis-shapen pans which may be unstable.  
DO NOT use round base woks directly on the pan supports.  
DO NOT use the glass lid (if fitted) as a working surface.  
Each burner is fitted with a spark ignitor for lighting the gas. To ensure rapid lighting of the burners every time they  
are used, the ignitors must be kept clean and dry. Remove any food spillage or cleaning materials from the  
electrode using a small nylon brush such as a tooth brush. Access to the electrode can be achieved by lifting off the  
loose burner parts carefully when the burners are cool.  
When the hotplate burner bodies and caps are removed for cleaning, be careful not to drop any food particles or  
cleaning materials into the burner bases, to avoid the possibility of blocking the gas jets.  
If aluminium based pans are used, a silvery deposit may appear on the top edge of the pan support fingers. See  
'Care and Cleaning' section for cleaning information.  
SAFETY REQUIREMENTS FOR DEEP FAT FRYING  
1. Never fill chip pans more than one third full with oil or fat.  
2. Never leave oil or fat unattended during the heating or cooling period.  
3. Never heat fat or fry with a lid on the pan.  
4. Always dry food thoroughly before frying, and lower it slowly into the hot oil or fat. Frozen foods in  
particular will cause frothing and spitting if added too quickly.  
5. Always keep the outside of the pan clean and free from streaks of oil or fat.  
HOW TO DEAL WITH A FAT FIRE  
1. Do not move the pan.  
2. Turn off the hotplate burners.  
3. Smother the flames with a fire blanket or damp cloth to extinguish the fire. Do not use water or a fire  
extinguisher as the force of it may spread the burning fat or oil over the edge of the pan.  
4. Leave the pan for at least 60 minutes before moving it.  
N.B.: After prolonged used of the gas hob there may be some small amount of discolouration in the area around the  
large burners. This is normal and can be easily removed using propriety stainless steel cleaning agents. We have  
included a sample of our own recommended stainless steel cleaner which will help maintain your new cooker in  
pristine condition.  
1 4  
Usa of Grill  
GRILLING MUST BE DONE WITH THE GRILL DOOR OPEN.  
CONTROL KNOBS MAY BECOME HOT DURING GRILLING.  
CAUTION: ACCESSIBLE PARTS WILL BECOME HOT WHEN THE GRILL  
IS USED - CHILDREN SHOULD BE KEPT AWAY.  
To operate the grill proceed as follows:  
l Open the grill door and remove the grill pan.  
l Push in and turn the control knob clockwise to the large flame symbol. Continue to push in the  
control knob for at least a further 5 seconds after the gas has lit, to allow time for the safety  
device to operate. If the burner extinguishes when the control knob is released, repeat the  
procedure ensuring the control knob is fully depressed and allowing more time for the safety  
device to operate.  
Grill Pan Handle  
l Turn the control knob anti-clockwise to the desired setting. There is a delay of about six seconds whilst the  
safety device operates before the burner comes on full. Only turn the control knob between the large  
flame symbol and the small flame symbol when adjusting the setting.  
Slide the grill pan along the runner towards the rear of the grill compartment until it stops. An  
odour may be noticed when first using the grill - this schould cease after a short period of use.  
Grill can be started from cold but for the best result preheat for approximately five  
minutes. Most cooking is done with the heat on full, but it may be necessary after sealing the  
food to reduce the heat as required.  
For au gratin dishes eg. Macaroni Cheese and meringue toppings eg. Baked Alaska place the  
dish on the floor of the grill compartment. The base of the grill pan can be used for warming  
fruit garnishes on the reduced setting.  
DO NOT cover the grill pan or grid with aluminium foil as this can hold fat, intensify the heat and create a fire hazard.  
In the event of the burner flames being accidentally extinguished, turn off the burner control and do not  
attempt to re-ignite the burner for at least one minute.  
Relighting‘  
the burner  
The grill pan handle is detachable from the pan, to facilitate cleaning and storage. Fix the grill pan  
handle securely in position before use.  
Fixing the Grill Pan  
Handle  
The handle fits onto the grill pan edge with the small recess, Fig.1.  
Tilt the handle over the recess and slide it towards the centre, Fig.2.  
Ensure the handle is fully located. Insert the washer and fixing screw and tighten fully to ensure handle  
is secured, Fig.3.  
Always hold the dripping pan handle in the highlighted zone marked "OK" in figure 4.  
OK  
Recess  
Fig. 1  
Fig. 4  
Fig. 2  
Fig. 3  
NO  
Always fit the screw prior to use.  
The food to be cooked should be placed on the grill pan/grill pan food support.  
Place the grill pan on the runners and push back to the stop position when the grill pan is  
correctly positioned beneath the grill element.  
Plates and dishes placed on the floor of the grill compartment will be heated when the oven is  
in use.  
1 5  
Usa ofTop Oven  
Theovenhasdifferentheatzones-thethermostatsettingsrefertothetemperatureonthemiddleshelf;abovethisshelfitis  
hotterandbelowitiscooler. Twoshelvesenablefulluseofthetemperaturesinsidetheoven.  
Eachshelfhasasafetystoptopreventiffrombeingpulledouttoofarwhenattendingtofood. Shelvesareremovedfromthe  
ovenbypullingthemouttothestopandthenliftingthematthefronttowithdraw.  
Thegrillpanwithoutthehandlecanbeusedintheoven. Themaximumsizeofbakingtraythatshouldbeusedis300mmx  
330mm(12"x13").  
TO USE THE OVEN 1. Place oven shelves in the chosen positions (refer to cooking charts).  
2. Push in and turn the control knob fully anti-clockwise. Continue to push in the control knob for at least a further 5  
seconds after the gas has lit to allow time for the safety device to operate. If the burner extinguishes when the control  
knob is released, repeat the procedure ensuring the control knob is fully depressed and allowing more time for the  
safety device to operate.  
3.Turn the control knob clockwise to the required setting (refer to cooking chart).There is a delay of about six  
seconds whilst the safety device operates before the burner comes on full.  
4.To turn off, turn the control knob fully clockwise the the symbol 0.  
Never place dishes on the oven base over the burner.  
An odour may be noticed when first using the oven - this should cease after a short period of use.  
5. The oven temperature control marking are gas marked 0 to 9.  
The equivalent degrees Celsius (sometimes called Centigrade) and degrees Fahrenheit are shown below as a guide.  
MAIN OVEN  
MAIN OVEN  
(Centre Oven Temperature)  
(Centre Oven Temperature)  
Gas Mark  
Gas Mark  
Celisus  
Fahrenheit °F  
°C  
Celisus  
Fahrenheit °F  
°C  
5
210  
220  
230  
240  
245  
410  
430  
445  
465  
475  
S
110  
145  
160  
180  
229  
290  
320  
355  
1
2
3
7
9
195  
385  
RELIGHTING  
THEBURNER  
Intheeventoftheburnerflamesbeingaccidentallyextinguished, turnofftheburnercontrolanddonotattempttore-ignite  
theburnerforatleastoneminute  
COLD START  
COOKING  
Anythingrequiringlongslowcookingsuchascasserolesandrichfruitcakescanbeputintoacoldoven. Satisfactoryresultscan  
alsobeobtainedwithcreamedmixture,richpastriesoryeastmixtures,butforperfectionwerecommendpreheatingtheoven  
forabout15minutes.  
ROASTING OF  
LARGE POULTRY  
Themaximumweightofpoultrythatcanbeaccommodatedis8kg(18Ibs)ofsuitableshape. Itisimportanttocheckthatthe  
birdDOESNOToverhangtheburneratthebackoftheoven.  
Itisvitallyimportanttostrictlyadheretothebasicprinciplesoffoodhandlingandhygienetopreventthepossibilityof  
bacterialgrowth.  
1. Iffoodistobefrozenornotservedimmediately, coolitinacleancontainerasquicklyaspossible.  
2.Completelythawfrozenfoodintherefrigeratorbeforereheating.  
3. Re-heatfoodthoroughlyandquicklyeitheronthehotplateorinahotoven, Mk. 6,andthenserveimmediately.  
4. Onlyre-heatfoodonce.  
STORAGE AND  
RE-HEATING  
OF FOOD  
‘COOK CHILL’  
DISHES  
Theseshouldalwaysbeplacedinapre-heatedovenideallyonthefirstorsecondshelfposition. Followthepacketinstructions  
forcookingtime.  
ALUMINIUM FOIL  
IfusingAluminiumFoil:  
1. Rememberthatitisimportanttoincreasethecookingtimebyonethird.  
2. Neverallowthefoiltotouchthesidesoftheoven.  
3. Nevercovertheoveninteriorwithfoil.  
4.Nevercovertheovenshelveswithfoil.  
1 6  
Oven Cooking Chart  
The following times and setting are for guidance only. You may wish to alter the setting to give a result more to your  
satisfaction. When a different setting to that shown below is given in a recipe, the recipe instructions should be  
followed. Allow 15 minutes preheat for best results. Always turn the thermostat knob to Mark 9 before selecting the  
appropriate gas Mark. Shelf position 1 is the highest.  
Food  
Gas  
Shelf  
Approx. Cooking Time and Comments  
Mark  
Position  
Fish  
Oily and white fish  
Meat and Poultry  
Beef  
3 or 4  
4
25-60 mins. depending on recipe  
4 or 5  
5
4
4
25-30 mins per 450g (1 Ib) + 25 mins. extra  
40 mins per 450g (1 Ib) covered in foil plus 40 mins.  
extra  
Ham  
Lamb  
5
4
30 mins per 450g (1 Ib) + 30 mins extra  
40 mins per 450g (1 Ib) + 40 mins extra  
25 mins per 450g (1 Ib) + 25 mins extra  
25 mins per 450g (1 Ib) + 25 mins extra  
15-20 mins per 450g (1 Ib) + 20 mins  
2-6 hrs. depending on cut of meat  
Pork  
5
4
Chicken  
5
4
Duckling & Goose  
Turkey  
5
4
4 or 5  
3
4 or 5  
3or4  
Casseroles  
Vegetables  
Baked jacket potatoes  
4 or 5  
3
4
1½ - 3 hrs. until soft, depending on size  
Puddings  
1¾-2½ stand dish on baking tray and started with  
warm milk  
Milk Puddings (500ml/1 pt)  
3
Baked Custard (500ml/1 pt)  
Baked Sponge Puddings  
Baked Apples  
3
4
3
1
6
5
4
45-60 mins. bain-marie  
40-50 mins  
3
3
30-45 mins depending on type and size of apples  
15 mins or until "tinged" with brown  
45-60 mins  
Meringue Topped Puddings  
Apple Tart (1 x205mm/8//)  
3or4  
2
2
Fruit Crumble  
35 -45 mins  
Cakes, Pastries & Biscuits  
Small Cakes 2 trays  
1 tray  
5
5
4
5
1
2
4
2
7
2
4
6
5
7
6
2 and 4  
15-25 mins.  
2
15-22mins.  
Victoria sandwich (2 x 7")  
Swiss Roll (3 egg quantity)  
Meringues  
2 and 4  
20-30 mins  
2
15-20 mins.  
3
2-3 hrs  
Christmas cake (1 x 205mm / 8")  
Madeira cake (1 x 180mm / 7")  
Rich Fruit cake (1 x 180mm / 7")  
Scones  
3
Time depending on recipe  
1¼-1½ hrs.  
4
4
Time depending on recipe  
10-20 mins.  
1 and 3  
Shortbread (1 x 180mm / 7")  
Biscuits  
3
55 -65 mins.  
1 and 3  
10-20 mins.  
Shortcrust Pastry  
2
15 - 60 mins depending on use.  
20-30 mins.  
Rich Short Crust  
1 and 3  
Flaky/Puff Pastry  
2
2
10-30 mins.  
Choux Pastry  
20-30mins.  
Yeast Mixtures  
Bread - rolls  
7
2 and 4  
20-30 mins.  
Miscellaneous  
Yorkshire Pudding:- large  
individual  
7
7
1
2
30-40 mins  
20-30mins  
When baking with two trays or tins on two levels, the top tray is removed first and the lower tray moved up to the top  
position for a few minutes longer.  
Soft Margarine -  
Use the oven settings recommended by the margarine manufacturer and not those indicated on the cooking chart.  
1 7  
Using the Main Oven for Other Functions  
SLOW Setting  
‘SLOWCOOK’  
This is used for slow cooking, keeping food warm and warming plates for short periods. Extra care  
should be taken when warming bone china, as it may be damaged in a hot oven.  
DO NOT place food or plates directly on the oven floor as this could damage both the oven  
lining and the plates which are being warmed.  
Advantages of “SLOW” cooking are:  
The oven stays cleaner because there is less splashing.  
Timing of food is not as critical, so there is less fear of overcooking.  
Inexpensive joints of meat are tenderised.  
Fully loading the oven can be economical.  
Cooking times can be extended in some cases by up to 2 hours.  
Operation:  
1. Place the prepared food in the main oven and ensure the door is fully closed.  
2. Select ‘SLOWCOOK’ (Slow Cooking Temperature) by turning the Main Oven Control clockwise  
ensuring the oven door is fully closed.  
Storage and re-heating of food:  
1. If food is to be frozen or not used immediately, place it in a clean container and cool as soon as  
possible.  
2. Always thaw frozen food completely in the refrigerator before re-heating.  
3. Always reheat food thoroughly and ensure it is piping hot before serving.  
4. Only re-heat food once.  
Points to consider when preparing food for “SLOW” cooking:  
1. Make sure that the dishes to be used will fit into the oven ensuring enough room for air to circulate.  
2. All dishes cooked on the slow setting will require a minimum of 6 hours, however, if they are cooked  
for 1 -2 hours longer then deterioration in their appearance may be noticed.  
3. Never cook joints of meat over 2.7kg (6 Ib) or poultry over 2.0kg (4lb 8oz).  
We do not recommend that joints of meat or poultry are stuffed before cooking on the slow setting.  
4. To seal in the meat juices, always cook meat or poultry at 170°C for 30 minutes before wrapping in  
foil and placing on a rack over a tin (to allow good air circulation) before turning the control to the slow  
setting and cooking immediately.  
5. Always ensure that joints of pork and poultry are thoroughly cooked by checking with a meat  
thermometer before serving.  
6. Always thaw frozen foods completely before cooking. We do not recommend placing frozen food in  
the oven to cook.  
7. Always bring soups, liquids and casseroles to the boil before placing in the oven.  
8. Ensure that casserole dishes have a good seal (not airtight) and cover to the top with foil to prevent  
loss of moisture.  
9. Ensure that fruit and vegetables are cut into even sized small pieces to cook properly.  
10. Always adjust seasoning before serving.  
11. If using dried red kidney beans it is important that the beans are soaked and then boiled fora  
minimum of 10 minutes before using in any dish to destroy any toxins.  
12. When cooking fish or egg dishes it may be necessary to check during cooking to avoid  
overcooking.  
1 8  
Care and Cleaning  
Remove the grill pan and the wire grid food support, it is best to wash these items immediately after  
Grill  
use to prevent stains from being burnt on when used again. Wipe out the Grill compartment, use a fine  
steel wool soap pad to remove stubborn stains from the grill runners and the floor of the compartment.  
Wipe over the control panel with a damp cloth and polish with a dry cloth.  
Do not use cream cleaners, oven cleaners or aerosols, scouring pads or abrasive powder for  
Control Panel  
cleaning the plastic knobs as damage will occur.  
It is advisable to clean the decorative trims regularly to prevent any build up of soiling. The  
recommended method of cleaning is to wipe over the trims with a soft cloth wrung out in warm water or  
mild non-abrasive cleaner. (If in doubt try the cleaner on a small area of trim which is not noticeable in  
normal use). Then, after wiping with a cloth wrung out in clear water, dry with a soft clean cloth.  
Decorative Trims  
Wipe over the outer door glass panels with a cloth wrung out in warm soapy water, then after wiping  
with a cloth wrung out in clear water, dry with a soft clean cloth. Ensure that glass doors are not  
subjected to any sharp mechanical blows.  
Doors  
Glass Inner Door Panel (where fitted) – open the door fully and carefully slide the inner glass  
towards you, taking care not to allow the glass to fall. The glass panel may now be washed at the sink.  
Stubborn stains can be removed by using a fine steel wool soap pad. Ensure the glass panel is not  
subjected to any sharp mechanical blows. Take particular care not to damage the inner surface  
which is coated with a heat reflective layer. After cleaning, rinse and dry with a soft cloth. For slight  
soiling the inner glass panel may be cleaned, while still warm, without removing it from the door.  
Warning: Oven must not be operated with inner door glass removed.  
Take care during cleaning not to damage or distort the door seals. Do not lift the door seal from the  
oven chassis, if necessary remove the seal by carefully unhooking the corner clips.  
Take care that the rating label edges are not lifted during cleaning, and furthermore that the lettering is  
not blurred or removed.  
Remove the rod shelves and grill pan. Use a fine steel wool soap pad to remove stubborn stains from  
the rod shelves, grill pan and the floor of the oven. Clean the glass part of the oven door using a  
sponge and a non-abrasive cleaning product, then dry thoroughly with a soft cloth. Do not use rough  
abrasive material or sharp metal scrapers as these could scratch the surface and cause the glass to  
crack.  
Ovens  
The shelf supports are removable and dishwasher safe.  
Oven Shelf  
Supports  
To remove hold the support at the front and pull away from the oven side, this can then be cleaned in  
a sink or a dishwasher. When removed it allows access to the oven side, which can be cleaned with  
warm soapy water.  
To refit the support, insert the longer leg into the rear fixing hole and push in the front leg.  
Open the oven door and remove the rod shelves. Using a suitable cloth to protect the fingers grip the  
light glass dome, unscrew anti-clockwise and lift. Reach into the aperture with fingers, and unscrew the  
lamp anticlockwise. Fit replacement lamp (25W 300°C rated SES), refit dome.  
Oven Lamp  
Replacement  
WARNING: To avoid electric shocks - please ensure that the electricity supply to the appliance  
is switched off and the appliance is fully cold, before removing the lamp lens.  
1 9  
Cooking Results Not Satisfactory?  
Problem  
Grilling  
Check  
Uneven cooking front to Ensure that the grill pan is positioned centrally below  
the grill element.  
back  
Fat splattering  
Ensure that the grill is not set to too high a  
temperature.  
Oven Baking  
Uneven rising of cake  
Ensure that the oven shelves are level by using a  
spirit level on the rod shelf and adjusting, using  
suitable packing e.g. wood, under the feet of the  
appliance. This should be checked both left to right  
and front to back. Ensure that the food is positioned  
centrally in the oven.  
Sinking of cakes  
The following may cause cakes to sink:  
1. Cooking at too high a temperature.  
2. Using normal creaming method with soft margarine.  
Over/Under cooking  
Fast/Slow cooking  
Refer to the cooking times and temperatures given in  
the oven temperature charts, however, it may be  
necessary to increase or decrease temperatures by  
10°C to suit personal taste.  
Do not use utensils greater than 2¼ ins in height.  
Uneven cooking of  
cakes  
1. Too large baking sheet used. (See 'Cookery Notes')  
2. Over loading of oven and always ensure even air  
gaps around baking tins.  
Uneven rising of cake  
Ensure that the shelf is level (see above) and that the  
food is positioned centrally in the oven.  
Food is taking too long Only cook one item at a time to avoid overloading the  
to cook oven.  
2 0  
Something Wrong with your Cooker?  
Before contacting your nearest Service Centre/Installer, check the problem guide below; there may be nothing wrong  
with your cooker.  
Problem  
Ignition does not work  
Check  
If all burners fail to ignite:  
Check that sparks appear at the burners;  
A clicking noise should be heard.  
If not  
Check that the plug is plugged in to a  
13amp Electric socket and the supply  
is switchedon.  
If all burners still fail to ignite  
Top Cavity  
Grill Burner  
Check and replace if necessary the 13amp fuse  
If only one burner fails to ignite  
Check that the burner is dry and that spillage of food or  
cleaning fluid remains are not affecting the Ignitor or burner  
ports.  
Clean away any debris with a dry nylon brush such as an  
old dry toothbrush.  
If a wire wool pad has been used for cleaning around the  
burner ensure the Ignitor is free from any stray strands.  
Any water on the burner should be dried with a cloth or  
kitchen towel.  
Burner Ports  
Burner Ports  
Oven Control  
Ignitor  
Hotplate Burner  
Hob Top  
On the hotplate make sure that all burner  
parts are correctly seated  
Ignitor  
For correct ignitionof oven/grill burners press theignitionbutton  
and then push in and turn control knobs anti-clockwise.  
Continue to press the ignition button until the spark lights the gas.  
Once alight release the ignition button and continue to hold the  
control knob in for a further 6 to 10 seconds.  
Oven or Grill will not stay lit  
when the control knob is released  
Control Panel  
Control Knobs  
Then release the control knob and set to the required temperature.  
The flame should now stay alight.  
If the flame does not hold and goes out wait 30 seconds and try  
again  
Grill Control  
Check that the temperature has been set in accordance with  
the temperature charts. It may be necessary to increase or  
decrease the recommended temperature by 10 C to suit your  
taste  
Oven Temperature seems too  
high or too low  
Check the temperature and shelf position are as recommended  
in the temperature charts  
Oven does not cook evenly.  
Check that the Utensil being used in the oven allow sufficient  
air flow around them.  
Check that the cooker is level.  
Check that your pans conform to the recommendations in  
these instructions.  
Hotplates are slow to boil or will  
not simmer  
This is normal and should cease after a short period.  
Condensation and steam is a by product of cooking food  
with a water content.  
Odour or smoke when using your new cooker  
Condensation / Steam in the Oven After Use  
To help minimise always:  
A) Try to avoid leaving food in the oven to cool after being cooked  
B) Use a coved Utensil wherever possible  
Steam and/or condensation may appear from the vent at the rear of  
the appliance when using an oven, particularly when cooking foods  
with a high water content (Such as Oven Chips or Chicken).  
This is normal and any excess should be wiped off  
Condensation on the Wall at the Rear of the Cooker  
2 1  
Technical Characteristics  
Oven  
Dimensions (HxWxD): 34x37,5x34 cm  
Volume:43 Litres  
Voltage and Frequency  
Burners:  
220-240V~ 50Hz  
Adaptable for use with all the types of gas indicated on the data plate.  
This appliance conforms with the following European Economic Community directives:  
-
-
-
-
-
2006/95/CEE of 12/12/06 (LowVoltage) and subsequent modifications;  
89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications;  
90/396/EEC of 29/06/90 (Gas) and subsequent modifications (only for models which use gas);  
93/68/EEC of 22/07/93 and subsequent modifications.  
2002/96/EC  
The European Directive 2002/96/EC onWaste Electrical and Electronic Equipment (WEEE), requires that old  
household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old  
appliances must be collected separately in order to optimise the recovery and recycling of the materials they  
contain and reduce the impact on human health and the environment.The crossed out “wheeled binsymbol  
on the product reminds you of your obligation, that when you dispose of the appliance it must be separately  
collected.  
Consumers should contact their local authority or retailer for information concerning the correct disposal of  
their old appliance.  
Mains frequency and voltage of the electric section and  
characteristics of the gas section  
Model  
Gas section  
Rated power  
Class  
kW (1)  
Langdale  
C50GLB  
C50GLK  
C50GLW  
C50GLS  
C50GLX  
C50LCIK  
C50LCIW  
C50GCIK  
C50GCIW  
12,50 (909 g/h - G30)  
(893 g/h - G31)  
II2H3+  
(1) The values in g/h refer to the capacities with liquid gas (Butane,  
Propane).  
2 2  
Electronic timer  
The electronic timer displays the time and the timer function with countdown.  
Note: This may be set while the oven is switched off or while it is switched on.  
To set  
the clock  
1. Press the  
button several times until the  
icon and the first two numerical digits on the display  
start to flash.  
2. Use the “+” and “-” buttons to adjust the hour value.  
3. Press the  
button again so that the other two numerical digits on the DISPLAY begin to flash.  
4. Use the “+” and “-” buttons to adjust the minute value.  
5. Press the  
button again to confirm.  
Note: If none of the buttons are pressed, the settings will be confirmed automatically after 10 seconds  
have passed.  
To set  
Note: This function does not interrupt cooking and does not affect the oven; it is simply used to  
the timer  
activate the buzzer when the set amount of time has elapsed.  
1. Press the  
button several times until the  
icon and the first two numerical digits on the display  
start to flash.  
2. Use the “+” and “-” buttons to adjust the hour value.  
3. Press the  
button again so that the other two numerical digits on the DISPLAY begin to flash.  
4. Use the “+” and “-” buttons to adjust the minute value.  
5. Press the  
button again to confirm.  
The countdown will then be displayed; at the end of this period of time the buzzer will sound (this may  
be stopped by pressing any of the buttons, or it will stop of its own accord after one minute).  
Press button “-” up until 0 00.  
To cancel a  
previous setting  
2 3  
Key Contacts  
After Sales Service  
Over 1200 trained specialists, directly employed by us, ensure that you can have complete confidence in  
both the appliances and services we offer.  
Repair Service and Information Desk  
UK: 08709 066 066  
(Open 8 to 8 Mon - Fri, 8 to 6 Sat, 10 to 4 Sun & Bank Holidays)  
Republic of Ireland: 1850 302 200  
Note: Our operators will require the following information:  
Model number:  
Serial number:  
Extended Warranties  
UK: 08709 088 088  
(Open 8 to 8 Mon - Sun)  
Republic of Ireland: 1850 502 200  
Genuine Parts and Accessories  
UK: 08709 077 077  
(Open 8-30 to 5-30 Mon - Fri & 9 to 12 Sat)  
Republic of Ireland: (01) 842 6836  
Indesit Company UK LTD, Morley Way, Peterborough, PE2 9JB.  
04/2008 - 19506068204  

GE 27980 User Manual
Frigidaire 790 42741402 User Manual
Fluke VICTOREEN 875 User Manual
Dell Computer Monitor ST2220TC User Manual
DCS BGC 3048 User Manual
Dacor ACTK30 User Manual
Brother P touch 550 User Manual
AT T DECT 6 0 EL52401 User Manual
Acer X213H User Manual
Acer AL1917C User Manual