USER GUIDE
2-PORT USB 3.0 SUPERSPEED PCI EXPRESS CARD
Model: 29055
INTRODUCTION
Thank you for purchasing the 2-Port USB 3.0 SuperSpeed PCI Express Card. The 2-Port USB 3.0
SuperSpeed PCI Express Card adds SuperSpeed USB capabilities to your computer. Simply install this
card into an available PCI slot on your computer to add two USB 3.0 SuperSpeed ports. SuperSpeed
USB supports transfer rates of up to 5 Gbps- up to 10 times faster than USB 2.0. The 2-Port USB 3.0
SuperSpeed PCI Express Card is ideal for quickly transferring large amounts of data from such devices
as external hard drives, memory card readers, real-time video cameras, and other data intensive USB
devices. We recommend that you read this manual thoroughly and retain for future reference.
2
FEATURES
™ Adds two USB 3.0 A-Male ports to a computer
™ Connects internally via the PCI-e connector
™ 5 Gbps signaling rate- 10X faster than USB 2.0
™ Backwards compatible with USB 2.0
™ Improved power efficiency over USB 2.0
™ Ideal for large data transfers from external hard drives, real-time video cameras, and other data
intensive devices
3
SYSTEM REQUIREMENTS
™ Operating System: Windows 7, XP, or Vista™
4
PACKAGE CONTENTS
™ 2-Port USB 3.0 SuperSpeed PCI Express Card
™ Driver CD
™ User Guide
5
DEVICE OVERVIEW
USB 3.0 Ports
6
DRIVER INSTALLATION
Before you install the device in your computer, you will need to install the necessary driver for proper
operation. Please follow the procedure below.
For Windows XP, Vista, Windows 7
Note: The following setup is an example shown using a Windows XP operating system. Some
screenshots may vary slightly depending on your operating system. The setup wizard is designed to step
you through each part of the driver installation process successfully.
Step 1
Insert the CD provided with this product and click Install
Driver. The following screen will appear. Click Next.
7
DRIVER INSTALLATION
Step 2
After reading the End-User License Agreement, please
select “I accept the terms in the License Agreement”
and click Next.
Step 3
Please click Browse to choose the destination folder, and
then click Next.
8
DRIVER INSTALLATION
Step 4
Click Install to begin driver installation.
The driver installation may take a few minutes. You may
also get a software installation Windows security pop-up
during this time. Click Continue Anyway when it appears to
complete the installation.
9
DRIVER INSTALLATION
Step 5
When the installation has completed, click Finish to exit the
setup wizard.
10
DEVICE INSTALLATION
Step 1
Turn off your computer and remove the cover/panel to expose the PCI slot.
Step 2
Plug the 2-Port USB 3.0 Card into the PCI slot on the computer.
Step 3
Replace the cover/panel and turn on your computer.
When your computer starts up, a Found New Hardware Wizard will appear.
Note: The following setup is an example shown using a Windows XP operating system. Some
screenshots may vary slightly depending on your operating system. The setup wizard is designed to step
you through each part of the driver installation process successfully.
The process outlined below will have to be completed two times because there are two USB 3.0 ports
that need to be installed and recognized.
11
DEVICE INSTALLATION
Step 4
When the Found New Hardware Wizard appears, select
Yes, this time only, and click Next.
Step 5
Choose Install the software automatically and click Next.
The Windows security pop-up may appear during this
process. Click Continue Anyway to continue with the
installation.
12
DEVICE INSTALLATION
Step 6
Click Finish to complete the installation and exit the
wizard.
Step 7
The Found New Hardware Wizard will appear again. Repeat steps 4-6 for second USB 3.0 port
installation.
13
VERIFY DEVICE INSTALLATION
After you have completed the driver and device installation, you can go to the Device Manager to verify
the product is installed and recognized properly.
Windows XP
Windows Vista/Windows 7
14
TECHNICAL SPECIFICATIONS
Product No.
Complies USB Rev.
29055
Ver. 3.0
Revision 2.0;
PCI Bus Power
Management Interface
Specification: Revision
1.2
PCI Express Base
Specification
Connectors
(Downstream)
USB 3.0 Type A x2
Low-speed (1.5Mbps)/
Full-speed (12Mbps)/
High-speed
Data Speed Support
(480Mbps)/ Super-
speed (5Gbps)
Control/ Bulk/
Interrupt/
Date Transfer Type
Support
Isochoronous
500 mA (max.)
.20 lbs
Power to Ports
Product Weight
15
CABLES TO GO™ ONE YEAR WARRANTY
At Cables To Go, we want you to be totally confident in your purchase. That is why we offer a one year
warranty on this device. If you experience problems due to workmanship or material defect for the
duration of this warranty, we will repair or replace this device. To request a Return Merchandise
Cables To Go
3555 Kettering Blvd.
Moraine, OH 45439
1-800-506-9607
16
IMPORTANT SAFETY INFORMATION
! Do not plug the unit in any outlet that does not have enough current to allow the device to function. Refer to the
specifications in this manual for power level of the unit.
! Liquid:
If this unit or its corresponding power adapter has had liquid spilled on or in it, do not attempt to use the unit.
Do not attempt to use this product in an outdoor environment as elements such as rain, snow, hail, etc. can
damage the product.
! In case of a storm, it is recommended that you unplug this device from the outlet.
! Avoid placing this product next to objects that produce heat such as portable heaters, space heaters, or heating
ducts.
! THERE ARE NO USER SERVICEABLE PARTS
Do not attempt to open this product and expose the internal circuitry. If you feel that the product is defective,
unplug the unit and refer to the warranty information section of this manual.
©2010 Cables To Go. Microsoft, XP, and Vista are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries. This product is not endorsed or manufactured by Microsoft
Corporation.
17
REGULATORY COMPLIANCE
FCC Conditions
This equipment has been tested and found to comply with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received. Including interference that may cause
undesired operation.
CE
This equipment is in compliance with the requirements of the following regulations:
EN 55 022: CLASS B
18
19
For more information on this product or to check for updated drivers,
manuals or frequently asked questions please visit our website.
VER. 1.0.4.16.10
|