CDA HVC60 User Manual

HVC60 / 70 / 90 Ceramic Hobs  
Manual for Installation, Use and Maintenance  
Customer Care Department • The  
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY  
T : 01949 862 012 F : 01949 862 003 E : [email protected] W : www.cda.eu  
Please note:  
Before operating this hob, please read the instructions carefully  
After unpacking the appliance, make sure it is not damaged. In case of doubt, do not use the appliance and contact your  
supplier.  
Remove all packaging and do not leave the packing materials in easy reach of children as they may cause serious injury. The  
packaging materials are recyclable.  
Always disconnect the appliance from the power supply before undertaking any cleaning or maintenance.  
Ceramic hobs become hot and remain hot during and immediately after use. Do not touch the hob until it has been allowed  
to cool.  
After use, please ensure that all the zones have been switched off.  
Keep children away from the appliance when in use.  
Pan handles should never stand out beyond the edge of the worktop. This will ensure children cannot reach them.  
Do not use pans with rough bases (e.g. cast iron) as these may scratch the hob surface.  
Ensure the base of the saucepan is clean and dry before placing it on the zone.  
Do not switch on the zones without cookware in place.  
Do not lean over the hob when it is in use.  
Do not drop heavy or sharp objects on to the hob top.  
Do not scratch the hob top with sharp objects.  
Follow the cleaning instructions carefully.  
Never put cooking foil or plastic materials on the hob top when it is hot. These materials could melt and cause damage to  
the hob.  
Do not leave inflammable materials on the hob top.  
Never use the hob top for storage or as a worktop.  
Do not leave wet or damp pan lids on the hob.  
Important  
Do not use the hob if the glass surface is cracked or damaged to prevent risk of electric shock, Disconnect it from the power  
supply.  
Do not use the hob if the electrical cord is damaged.  
When correctly installed, this hob meets all the safety requirements laid down for this type of product. However, special  
care should be taken around the underneath of the appliance as this area is not designed or intended to be touched and may  
contain sharp or rough edges, that may cause injury.  
This hob (Class 3) has been designed for use only as a cooking appliance. Any other use (e.g. heating rooms) should be  
considered incorrect and therefore dangerous.  
This appliance is not intended to be operated by any means of an external timer or separate remote control system.  
Make sure that electrical cords connecting other appliance do not come into contact with the hob top.  
Before disposing of an unwanted appliance, it is recommended that it is made inoperative and that all potentially hazardous  
parts are removed.  
2
Using your hob  
HVC60  
Zones:  
1.  
Front left 1.2 kW 140 mm  
2. Rear left 2.3 kW 210 mm  
3. Rear right 0.75/2.2 kW 120/210 mm dual  
4. Front right 1.2 kW 140 mm  
2
1
3
4
Control panel:  
5. Front left zone control  
6. Rear left zone control  
7.  
Rear right zone control  
8. Front right zone control  
9. Residual heat indicators  
10. Power indicator light  
5
6
7
8
9
10  
Fig.1  
HVC70  
Zones:  
1.  
Front left 1.2 kW 140 mm  
2. Rear left 0.8/2.2 kW 180x260 mm oval dual  
3. Rear right 1.2 kW 140 mm  
4. Front right 0.75/2.2 kW 120/210 mm dual  
3
4
2
1
Control panel:  
5. Front left zone control  
6. Rear left zone control  
7.  
Rear right zone control  
8. Front right zone control  
9. Residual heat indicators  
10. Power indicator light  
5
6
7
8
9
10  
Fig.2  
HVC90  
Zones:  
1.  
Front left 1.8 kW 180 mm  
2. Rear left 1.2 kW 140 mm  
3. Centre 0.8/2.2 kW 180x260 mm oval dual  
4. Rear right 0.75/2.2 kW 120/210 mm dual  
5. Front right 1.2 kW 140 mm  
2
3
4
5
Control panel:  
6. Front left zone control  
1
7.  
Rear left zone control  
8. Centre zone control  
9. Rear right zone control  
10. Front right zone control  
11. Residual heat indicators  
12. Power indicator light  
6
7
8
9
10  
12  
11  
Fig.3  
3
How to use the hob  
The ceramic surface of the hob allows fast transmission of heat vertically from the heating elements under the glass to the  
pans on the hob top.  
The heat does not spread horizontally, so the hob top remains relatively cool only a few centimetres from the zone in use.  
Please note:  
The heating elements are equipped with a temperature limiter that will switch the element off to prevent damage to the hob.  
The temperature limiter may also operate when incorrect pans are used or pans are poorly positioned. This will affect cooking  
performance.  
The temperature limiter can be seen in the zone as the straight line out from the centre of the element. This is not a fault with  
the hob.  
Using the single zones  
The heating element is formed of a coil of resistant material which  
reaches the required cooking temperature quickly.  
Hi-light cooking zone  
Ø 140mm  
Hi-light cooking zone  
Ø 180mm  
Before using the hob, first check the hob and the pan are clean and  
dry, then place the pan correctly on to the zone.  
Hi-light cooking zone  
Ø 210mm  
The power level for each zone can be regulated by turning  
the control knob to the required level between 0 (off) and 12  
(maximum).  
fig. 4  
Second element  
The power indicator light will switch on automatically when any of  
the zones are in use.  
Using the dual zones  
The dual zones are formed of two separate coils of resistant  
material.  
Hi-light oval  
double zone  
Hi-light double zone  
fig. 5  
fig. 6  
fig. 7  
To turn on the dual zone, turn the control knob fully clockwise to  
the position.  
Residual heat indicators  
The hob is equipped with residual heat indicators which warn when  
any of the zones are hot to the touch, both during and after cooking.  
A light will show on the display (fig 6 for HVC60/HVC70, fig 7  
for HVC90) to indicate a zone is hot until the zone is at a safe  
temperature to touch, when the residual heat indicator will the  
switch off.  
Please note:  
You should avoid touching the zones when the hob is in use, or  
when the residual heat indicator is on.  
In the event of a power cut, the residual heat indicators will  
illuminate after the power supply is restored. However, when  
there is no power supply to the hob the residual heat indicators will  
not work, so extra care must be taken.  
4
How to use the hob  
Cooking  
zone  
settings  
TYPE OF COOKING  
Cooking  
zone  
setting  
0
Switched OFF  
1
2
For melting operations (butter, chocolate).  
2
3
4
To maintain food hot and to heat small quantities  
of liquid (sauces, eggs).  
1
2
4
5
6
To heat bigger quantities; to whip creams and  
sauces. (vegetables, fruits, soups).  
3
Slow boiling, i.e.: boiled meats, spaghetti, soups,  
continuations of steam cooking of roasts, stews,  
potatoes.  
6
7
4
6
7
For every kind of frying, cutlets, uncovered cook-  
ing, i.e.: risotto.  
5
8
9
Browning of meats, roasted potatoes, fried fish,  
omelettes, and for boiling large quantities of  
water.  
6
10  
7
11  
12  
Fast frying, grilled steaks, etc.  
8
Switching on the second element (Double and  
oval zones only)  
9
10  
11  
12  
Heating  
Cooking  
Roasting-frying  
fig.8  
5
Efficient Use of your Hob  
The hob is equipped with zones of different sizes, designed to accommodate most shapes and sizes of pan. For best  
results, only use pans with flat bottoms and choose an appropriate zone depending on the size of the pan. The most  
efficient use of the hob is shown below, where the pan and zone are correctly chosen.  
Use pan lids where possible to minimize the energy usage of your appliance.  
To reduce the cooking time, set the control knob to its maximum position when you first switch the plate on. Once the  
zone has reached its temperature, then turn the control knob to the required position.  
As the zone will remain hot for a period of time after it has been switched off, five to ten minutes before the planned  
end of cooking time, turn the zone off. The residual heat in the hob will be sufficient to finish the cooking.  
Fig.9  
Zone Size  
140 mm  
Minimum Pan Size (mm)  
Maximum Pan Size (mm)  
110  
150  
160  
180 mm  
200  
210 mm  
180  
230  
140/230  
120/210 dual  
180 x 260 dual  
90/180  
150  
160 (280 when dual zone in use)  
It is very important that the pans used on the hob are made of a suitable material and have the correct type of base.  
The base should be flat and smooth, as any rough part on the pan base could scratch the ceramic hob top.  
Choose pans which are between the sizes recommended in the table above, and with bases that are as non-reflective as  
possible, e.g. dull and dark.  
Only pans recommended for use on ceramic hobs should be used.  
Pans with aluminium bases may leave silver streaks or spots on the hob. Glassware and pans with rough circular  
machined bases should not be used  
6
Care and Maintenance  
Always disconnect the appliance from the power supply before undertaking any cleaning or maintenance.  
You should use a non-abrasive cleaner to clean the hob top. Any abrasive cleaner (including Cif) will scratch the surface and  
could erase the control panel markings.  
Do not use steel wool, abrasive sponges or sharp utensils such as knives to clean the hob as these could damage the hob.  
The hob surface and the pans must be clean.  
Carefully remove any food remains (especially those containing sugar), dirt etc. as soon as is possible after spillage - using a  
ceramic hob scraper if necessary whilst the zone is still hot.  
Once they have cooled and hardened they become increasingly difficult to remove.  
Sugar, syrup and starch mixtures could permanently pit the hob surface if left to burn on and should be removed as quickly  
as possible after spillage.  
The stainless steel trims should be rinsed with water and dried with a soft, clean cloth, a chamois leather or an E-Cloth.  
If necessary, the control knobs can be removed for cleaning, but you should take care not to damage the seal nor to allow  
water inside the hob itself.  
All cleaner residues should be removed with a damp cloth.  
Types of residues  
Clean with  
Cleaning advice  
Wipe over the zone to be cleaned with a sponge and hot  
water, and then wipe off with a soft dry cloth.  
Light  
Cleaning sponge and soft cloth  
Wipe over the zone to be cleaned with a sponge and hot  
water, using a ceramic scraper to remove any large marks  
or stains and then wipe off with a soft dry cloth.  
Accumulated baked-on stains/  
dirt, sugar spills or melted plastics  
Cleaning sponge or glass scraper  
and soft cloth  
Pour a small amount of warm white vinegar onto the stain,  
leave it to stand, and then wipe off with a soft dry cloth.  
Rings and hard water residues  
White vinegar and soft cloth  
Important:  
Steam cleaners must not be used when cleaning this appliance.  
Mains electrical voltage:  
230 – 240Vac  
Total rated electrical consumption:  
HVC60  
HVC70  
HVC90  
6.9 kW  
6.8 kW  
8.6 kW  
If your Hob is not working:  
1. Check that the control knobs are switched on.  
2. Check that the mains supply has not been switched off.  
3. Check that the fuse in the spur has not blown.  
Contact CDA Customer Care  
A : Customer Care Department, The CDA Group Ltd, Harby Road, Langar, Nottinghamshire, NG13 9HY  
7
Mains Electricity Connection  
Warning! this appliance must be earthed  
We recommend that the appliance is connected by a qualified  
electrician, who is a member of the N.I.C.E.I.C. and who will comply  
with the I.E.E. and local regulations.  
This appliance is intended to be connected to fixed wiring and  
is not suitable for connection to a 13A plug or 13A supply.  
C
A
This appliance is intended to be connected to fixed wiring by a  
double pole switch, having a contact separation of at least 3mm in  
all poles. The switch must be positioned no further than 2m from  
the appliance.  
B
B
Fig.10  
Please note:  
The mains cable must only be replaced by a qualified electrician  
or service engineer and must be of equivalent or better rating  
(i.e. 2.5 mm² for HVC60/HVC70, 4mm² for HVC90,  
HO5RR-F, HO5VV-F or H05V2V2-F).  
C
G
E
This appliance is intended to be connected to the mains supply  
with a cable of cross section area 2.5 mm² (HVC60/70) or  
4mm² (HVC90). A larger cable will not fit the terminal  
connections.  
E
N
L
The marking of the current rating of the fuse or circuit breaker  
protecting this appliance should be marked on the  
socket outlet.  
F
D
Fig.11  
Assembly and electrical connection should be carried out by  
specialised personnel.  
When installing this product we recommend you seek the help  
of another individual.  
Ensure that the brass links are securely fitted. Failure to do so  
will prevent the hob from operating correctly.  
8
Fitting the Hob  
Unpacking the hob:  
Take care not to lose or mishandle any parts.  
Fitting position of the hob:  
This appliance must be installed a minimum of 50mm from any back wall and a minimum of 190mm away from any  
adjacent vertical surfaces, e.g. a tall cupboard end panel. This may be reduced to 100mm if the adjacent surface is resistant  
to fire (tiles or steel, for example). These dimensions are shown in Fig.12.  
If fitting a cooker hood above the hob:  
If a cooker hood is to be installed above the hob, the height of the hood above the hob must be at least 600mm (650mm is  
recommended) (Fig.13). If the instructions supplied with the hood dictate that the hood must be installed at a height greater  
than 600mm, then that height is the minimum required.  
Wall furniture requirements:  
The minimum height of any cabinet immediately above the hob is 900mm. The minimum height of any adjacent units  
(including light pelmets) is 400mm, unless they are manufactured from a material resistant to fire (steel, for example)  
Notes:  
Do not position this appliance above a refrigeration unit. The heat generated may cause the refrigeration unit to fail.  
This appliance is designed to be installed into cabinet units capable of withstanding temperatures of 65°C or greater above  
ambient temperature.  
If there is no oven to be built in below the hob, an isolation shelf should be fitted to protect the user from high  
temperatures. If the hob is to be installed above a working drawer, then a partition should be fitted to protect the contents  
and user from the heat generated during use.  
Never place perishable foods in the cupboard below the appliance.  
9
How to Install the Hob  
How to install the hob:  
Overall dimensions of the hob: HVC60 Width 590mm Depth 510mm  
HVC70 Width 770mm Depth 510mm  
HVC90 Width 900mm Depth 510mm  
Worktop cut-out dimensions:  
HVC60 Width 560mm Depth 490mm  
HVC70 Width 740mm Depth 490mm  
HVC90 Width 870mm Depth 490mm  
1. Make the required hole in the worktop. Before doing this, you must check the instructions supplied with any cooker hood  
to ensure that you will have the required clearance. The cut-out (Fig.12) shows a 60mm gap from the wall to the cut-out  
edge. The distance from the hob, when fitted, to the back wall is 50mm. If a splashback/worktop upstand is to be fitted,  
take this into account when cutting the hole. The minimum distance that the hob should be positioned away from the rear  
wall or splashback is 50mm.  
2. Position the hob seal, as shown in (Fig.14), ensuring that the ends meet without overlapping. Do not use silicone type sealant.  
3. Secure the hob to the worktop using the fixing brackets and screws supplied, as shown in (Fig.15). Remove any excess  
sealant after tightening the brackets. Do not over-tighten the fixing brackets.  
60mm  
490mm  
4
560mm  
740mm  
870mm  
1
190mm  
190mm  
Fig.12  
Fig.13  
3cm  
4cm  
Fig.14  
Fig.15  
10  
To contact our Customer Care Department, or for Service,  
please contact us on the details below.  
Customer Care Department • The  
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY  
T : 01949 862 012 F : 01949 862 003 E : [email protected] W : www.cda.eu  

Grundig XENTIA LXW 94 8625 User Manual
GE Monogram ZGU36N4R User Manual
GE General Electric Convection Oven cr401 User Manual
Gateway ALR 9200 User Manual
Emerson Computer Hardware MITX 430 User Manual
Elo TouchSystems ET 1525C Series User Manual
Electrolux Icon E30GC70ISS User Manual
Dacor CER304 User Manual
Belkin P73768 A User Manual
AT T E3813B User Manual