Black Box Computer Hardware VSP DLDVI1X2 User Manual

VSP-DLDVI1X2  
VSP-DLDVI1X4  
Dual Link DVI Splitters  
Easily split and distribute dual-link DVI source video  
to two or four different screens.  
Customer Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S.  
Support call 724-746-5500) • FREE technical support 24 hours a day, 7 days  
Information a week: Call 724-746-5500 or fax 724-746-0746 • Mailing address:  
Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018  
FCC and IC RFI Statements/NOM Statement  
FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY  
CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS  
This equipment generates, uses, and can radiate radio-frequency energy,  
and if not installed and used properly, that is, in strict accordance with the  
manufacturer’s instructions, may cause interference to radio communication.  
It has been tested and found to comply with the limits for a Class A computing  
device in accordance with the specifications in Subpart B of Part 15 of FCC rules,  
which are designed to provide reasonable protection against such interference  
when the equipment is operated in a commercial environment. Operation of this  
equipment in a residential area is likely to cause interference, in which case the  
user at his own expense will be required to take whatever measures may be  
necessary to correct the interference.  
Changes or modifications not expressly approved by the party responsible  
for compliance could void the user’s authority to operate the equipment.  
This digital apparatus does not exceed the Class A limits for radio noise  
emission from digital apparatus set out in the Radio Interference Regulation  
of Industry Canada.  
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant  
les limites applicables aux appareils numériques de classe A prescrites dans le  
Règlement sur le brouillage radioélectrique publié par Industrie Canada.  
Normas Oficiales Mexicanas (NOM)  
Electrical Safety Statement  
INSTRUCCIONES DE SEGURIDAD  
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes  
de que el aparato eléctrico sea operado.  
2. Las instrucciones de seguridad y operación deberán ser guardadas para  
referencia futura.  
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de  
operación deben ser respetadas.  
4. Todas las instrucciones de operación y uso deben ser seguidas.  
724-746-5500  
|
blackbox.com  
Page 3  
NOM Statement  
5. El aparato eléctrico no deberá ser usado cerca del aguapor ejemplo,  
cerca de la tina de baño, lavabo, sótano mojado o cerca de una alberca,  
etc.  
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales  
que sean recomendados por el fabricante.  
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea  
recomendado por el fabricante.  
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más  
allá a lo descrito en las instrucciones de operación. Todo otro servicio  
deberá ser referido a personal de servicio calificado.  
9. El aparato eléctrico debe ser situado de tal manera que su posición no  
interfiera su uso. La colocación del aparato eléctrico sobre una cama, sofá,  
alfombra o superficie similar puede bloquea la ventilación, no se debe  
colocar en libreros o gabinetes que impidan el flujo de aire por los orificios  
de ventilación.  
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor  
como radiadores, registros de calor, estufas u otros aparatos (incluyendo  
amplificadores) que producen calor.  
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo  
del tipo descrito en el instructivo de operación, o como se indique en el  
aparato.  
12. Precaución debe ser tomada de tal manera que la tierra fisica y la  
polarización del equipo no sea eliminada.  
13. Los cables de la fuente de poder deben ser guiados de tal manera que no  
sean pisados ni pellizcados por objetos colocados sobre o contra ellos,  
poniendo particular atención a los contactos y receptáculos donde salen  
del aparato.  
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las  
recomendaciones del fabricante.  
15. En caso de existir, una antena externa deberá ser localizada lejos de las  
lineas de energia.  
16. El cable de corriente deberá ser desconectado del cuando el equipo no  
sea usado por un largo periodo de tiempo.  
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean  
derramados sobre la cubierta u orificios de ventilación.  
Page 4  
724-746-5500  
|
blackbox.com  
NOM Statement  
18. Servicio por personal calificado deberá ser provisto cuando:  
A: El cable de poder o el contacto ha sido dañado; u  
B: Objectos han caído o líquido ha sido derramado dentro del aparato; o  
C: El aparato ha sido expuesto a la lluvia; o  
D: El aparato parece no operar normalmente o muestra un cambio en su  
desempeño; o  
E: El aparato ha sido tirado o su cubierta ha sido dañada.  
724-746-5500  
|
blackbox.com  
Page 5  
Safety Instructions  
Safety Instructions  
The splitters have been tested for conformance to safety regulations and  
requirements, and have been certified for international use. However, like all  
electronic equipment, the splitters should be used with care. Please read and  
follow the safety instructions to protect yourself from possible injury and to  
minimize the risk of damage to the unit.  
• Follow all instructions and warnings marked on this unit.  
• Do not attempt to service this unit yourself, except where explained in this  
manual.  
• Provide proper ventilation and air circulation and do not use near water.  
• Keep objects that might damage the device away from it and be sure to place  
this unit on a stable surface.  
• Use only the power adapter and power cords and connection cables designed  
for this unit.  
• Do not use liquid or aerosol cleaners to clean this unit. Always unplug the  
power to the device before cleaning.  
Page 6  
724-746-5500  
|
blackbox.com  
Table of Contents  
Table of Contents  
1. Specifications ................................................................................................8  
2. Overview ................................................................................................9  
2.1 Introduction........................................................................................9  
2.2 Features ..............................................................................................9  
2.3 What’s Included..................................................................................9  
2.4 Hardware Description.......................................................................10  
2.4.1 VSP-DLDVI1X2 .....................................................................10  
2.4.2 VSP-DLDVI1X4 ......................................................................11  
3. Configuration .............................................................................................12  
3.1 DIP Switch.........................................................................................12  
3.2 EDID Learning...................................................................................12  
4. Hardware Installation .................................................................................13  
Appendix. Troubleshooting..............................................................................15  
A.1 Contacting Black Box........................................................................15  
A.2 Shipping and Packaging...................................................................15  
724-746-5500  
|
blackbox.com  
Page 7  
Chapter 1: Specifications  
1. Specifications  
Audio Support — No  
CEC Channel — N/A  
DVI Compliance — DVI 1.1  
ESD Protection — (1) human-body model: +19kV (air-gap discharge)  
12 kV (contact discharge)  
Firmware Update — Via RS-232 port  
HDCP Compliance — No  
Housing — Metal enclosure  
Input DDC Channel — 5 volts (peak-to-peak, TTL)  
Input TMDS Channel — 1.2 volts (peak-to-peak)  
PCB Stack-Up — 4-layer board;  
Impedance control: Differential: 100 ohms,  
Single: 50 ohms  
Resolutions — Up to 2560 x 1600  
Video Bandwidth — 300 MHz  
Connectors — VSP-DLDVI1X2: Input: (1) DVI-I (29-pin female digital only),  
Output: (2) DVI-I (29-pin female digital only),  
RS-232: (1) mini DB9;  
VSP-DLDVI1X4: Input: (1) DVI-I (29-pin female digital only),  
Output: (4) DVI-I (29-pin female digital only),  
RS-232: (1) mini DB9  
Temperature Tolerance — Operating: 32 to 104° F (0 to 40° C);  
Storage: -4 to +140° F (-20 to +60° C)  
Relative Humidity — 20 to 90%, noncondensing  
Power — Input: AC input: 100–240 VAC, 50–60 Hz, 0.8 A;  
Output: 5 VDC, 4 A;  
Consumption (maximum): 15 Watts  
Size — VSP-DLDVI1X2: 1"H x 2.2"W x 8.2"D (2.4 x 5.7 x 21 cm);  
VSP-DLDVI1X4: 1.7"H x 3.9"W x 8.6"D (4.3 x 10 x 21.9 cm)  
Weight — VSP-DLDVI1X4: 1.6 lb. (0.7 kg);  
VSP-DLDVI1X2: 0.9 lb. (0.4 kg)  
Page 8  
724-746-5500  
|
blackbox.com  
Chapter 2: Overview  
2. Overview  
2.1 Introduction  
The Dual Link DVI Splitter (VSP-DLDVI1X2 or VSP-DLDVI1X4) transmits  
super-high-definition graphics to 2 or 4 different locations without losing  
quality. It can also function as a typical single link 4-port DVI splitter. Use the  
splitter for CAD, post production, broadcast, or control room applications.  
2.2 Features  
• DVI 1.1 compliant.  
• Provides a wide frequency range: up to 300 MHz.  
• Enables EDID learning using a DIP switch.  
• Firmware upgradable via an RS-232 connection.  
• Uses wallmount housing design for easy installation.  
NOTES:  
1. The VSP-DLDVI1X2 and VSP-DLDVI1X4 do not support HDCP.  
2. To correctly display dual link DVI, users must pay attention to the EDID  
content. The graphics card will send video according to the presented EDID.  
2.3 What’s Included  
Your package should contain the following items. If anything is missing  
or damaged, contact Black Box Technical Support at 724-746-5500  
VSP-DLDVI1X2:  
• (1) 1 x 2 Dual Link DVI Splitter  
• (1) 5-VDC, 4-A power supply  
• (2) mounting screws  
• This user’s manual  
VSP-DLDVI1X4:  
• (1) 1 x 4 Dual Link DVI Splitter  
• (1) 5-VDC, 4-A power supply  
• (2) mounting screws  
• This user’s manual  
724-746-5500  
|
blackbox.com  
Page 9  
Chapter 2: Overview  
2.4 Hardware Description  
2.4.1 VSP-DLDVI1X2  
The front panel of the splitter is blank metal. Figure 2-1 shows the back panel.  
Table 2-1 describes its components.  
6
7
1
2
3
4
5
Figure 2-1. VSP-DLDVI1X2 back panel.  
Table 2-1. VSP-DLDVI1X2 components.  
Number  
Component  
Dual-Link DVI IN connector  
Description  
1
Links to DVI input source.  
DVI output 1.  
2
Dual-Link DVI OUT connector  
3
4
Dual-Link DVI OUT connector  
DIP switch  
DVI output 2.  
Used for EDID learning.  
Used for firmware update  
and control.  
5
6
7
DB9 F connector  
Power signal LED  
Lights when power to the  
unit is on.  
+5-VDC 4-A interlocking  
power jack  
Connects to interlocking  
5-V, 4-A power supply.  
Page 10  
724-746-5500  
|
blackbox.com  
Chapter 2: Overview  
2.4.2 VSP-DLDVI1X4  
The front panel of the VSP-DLDVI1X4 splitter is blank metal. Figure 2-2 shows  
the back panel. Table 2-2 describes its components.  
1
3
4
6
7 8 9  
2
5
Figure 2-2. VSP-DLDVI1X4 back panel.  
Table 2-2. VSP-DLDVI1X4 components.  
Number  
Component  
Description  
1
Dual-Link DVI OUT connector  
DVI output 1.  
2
3
Dual-Link DVI OUT connector  
Dual-Link DVI IN connector  
DVI output 2.  
Links to DVI input source.  
4
5
Dual-Link DVI OUT connector  
Dual-Link DVI OUT connector  
DVI output 3.  
DVI output 4.  
Used for firmware update  
and control.  
6
7
8
DB9 F connector  
DIP switch  
Used for EDID learning.  
Lights when power to the  
unit is on.  
Power signal LED  
+5-VDC 4-A interlocking  
power jack  
Connects to interlocking  
5-V, 4-A power supply.  
9
724-746-5500  
|
blackbox.com  
Page 11  
Chapter 3: Configuration  
3. Configuration  
3.1 DIP Switch  
Figure 3-1 shows the DIP switch on the VSP-DLDVI1X2 or VSP-DLDVI1X4 unit.  
Table 3-1 describes the settings.  
Figure 3-1. DIP switch.  
Table 3-1. DIP switch settings.  
Pin #1  
Pin #2  
EDID Feature  
OFF (UP)  
OFF (UP)  
Default for dual-link mode.  
OFF (UP)  
ON (DOWN)  
Default for single-link mode.  
ON (DOWN)  
ON (DOWN)  
ON (DOWN)  
OFF (UP)  
EDID learning mode.  
Reserved mode.  
NOTE: For the VSP-DLDVI1X2 unit, only DVI output 2 can be used to learn EDID.  
For the VSP-DLDVI1X4 unit, only DVI output 4 can be used to learn EDID.  
3.2 EDID Learning  
Follow these steps to identify the output display.  
1. Connect the output display to Output 2 on the VSP-DLDVI1X2 or to Output 4  
on the VSP-DLDVI1X4.  
2. Adjust the DIP switch to EDID learning mode (both switches are OFF).  
3. Unplug the power adapter, then plug it back it again.  
4. The Power LED will start blinking.  
5. When the EDID learning is done, the LED will stop blinking.  
Page 12  
724-746-5500  
|
blackbox.com  
Chapter 4: Hardware Installation  
4. Hardware Installation  
Broadcast DVI Signal to 2 or 4 DVI Displays  
1. Switch off all devices, including monitors.  
2. Connect to the receivers.  
3. Connect a DVI source to the DVI IN port.  
4. Plug in a 5-VDC power supply (included).  
5. Power on the DVI monitors.  
6. Power on the DVI source.  
DVI cable  
Laptop with DVI output  
VSP-DLDVI1X2  
DVI cable  
DVI cable  
Display with DVI input  
Display with DVI input  
Figure 4-1. VSP-DLDVI1X2 installation diagram.  
724-746-5500  
|
blackbox.com  
Page 13  
Chapter 4: Hardware Installation  
DVI cable  
Laptop with DVI output  
VSP-DLDVI1X4  
DVI cables  
Displays with DVI input  
Displays with DVI input  
Figure 4-2. VSP-DLDVI1X4 installation diagram.  
Page 14  
724-746-5500  
|
blackbox.com  
Appendix: Troubleshooting  
Appendix. Troubleshooting  
A.1 Contacting Black Box  
If you determine that your splitter is malfunctioning, do not attempt to alter or  
repair the unit. It contains no user-serviceable parts. Contact Black Box Technical  
Support at 724-746-5500 or [email protected].  
Before you do, make a record of the history of the problem. We will be able to  
provide more efficient and accurate assistance if you have a complete  
description, including:  
• the nature and duration of the problem.  
• when the problem occurs.  
• the components involved in the problem.  
• any particular application that, when used, appears to create the problem or  
make it worse.  
A.2 Shipping and Packaging  
If you need to transport or ship your splitter:  
• Package it carefully. We recommend that you use the original container.  
• If you are returning the unit, make sure you include everything you received  
with it. Before you ship for return or repair, contact Black Box to get a Return  
Authorization (RA) number.  
724-746-5500  
|
blackbox.com  
Page 15  
Black Box Tech Support: FREE! Live. 24/7.  
Tech support the  
way it should be.  
Great tech support is just 30 seconds away  
at 724-746-5500 or blackbox.com.  
About Black Box  
Black Box provides an extensive range of networking and infrastructure  
products. You’ll find everything from cabinets and racks and power and surge  
protection products to media converters and Ethernet switches all supported  
by free, live 24/7 Tech support available in 30 seconds or less.  
© Copyright 2012. Black Box Corporation. All rights reserved.  
VSP-DLDVI1X2, version 3  
724-746-5500  
|
blackbox.com  

HP Hewlett Packard Hewlett Packard Computer Monitor LA2206X User Manual
Heath Zenith SL 5411 User Manual
Heath Zenith 122C User Manual
Haier HTF20 User Manual
Grundig DIGI 100 SERVICE MANUAL CUC 1807 User Manual
Daewoo DTC 20, DTC 21, DTY 21, DTY 25, DTY 28, DTY 29, DTZ 24, DTZ 28, DTZ 29 User Manual
Dacor Convection Oven MRWD30 User Manual
Cres Cor RO151FWUA18B User Manual
Canon V8000HDe User Manual
Bosch Appliances NES 730 UC User Manual 1