Black Box Computer Hardware LBPS310A KIT User Manual

LBPS310A-KIT  
LBPS311A  
LBPS312A  
Hardened PoL PoE Ethernet Extenders  
Hardened PoL PoE Ethernet Extenders  
Extends Power over Ethernet up to 1.2 km over ordinary  
voice-grade copper wire.  
Features Ethernet extension up to 2.2 km.  
Customer Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S.  
Support call 724-746-5500) • FREE technical support 24 hours a day,  
Information  
7 days a week: Call 724-746-5500 or fax 724-746-0746  
• Mailing address: Black Box Corporation, 1000 Park Drive,  
Lawrence, PA 15055-1018 • Web site: www.blackbox.com  
10/100Base-TX Hardened PoL/PoE Ethernet Extender  
Connect one end of the one pair copper wire to the RJ-11 phone jack or 2-pin  
Terminal Block interface of the Transmitter and connect the other end to RJ-11  
phone jack or 2-pin Terminal Block interface of the Receiver.  
Data can be transmitted between the Transmitter and the Receiver via copper wire.  
Physical Description  
The Port Status LEDs and Power Inputs  
Transmitter  
Receiver  
DC Terminal Block Power Inputs: 2.5A @ 48VDC (Peak current 3.26A). Two pairs of  
power inputs can be used to power up this Ethernet Extender. The redundant power  
supplies function is supported. You only need to have one power input connected to  
run the Ethernet Extender.  
DC JACK Power input: 2.5A @ 48VDC (Peak current 3.26A).  
User’s Manual  
2
10/100Base-TX Hardened PoL/PoE Ethernet Extender  
Power Input Assignment  
Power1  
48VDC  
DC Jack  
T:46-57V / R:46-57V DC  
Power Ground  
Power2  
Terminal  
Block  
T:46-57V / R:46-57V DC  
Power Ground  
Power3  
Earth Ground  
DIP Switch Down  
Transmitter  
Up  
PoL  
Disable Power over Link  
Std (Standard)  
Standard line speed  
Better noise immunity  
Enable Power over Link  
Per (Performance)  
Better line speed  
Type  
Poor noise immunity  
Receiver  
Mode  
Loc (Local)  
Set Receiver to Local Mode  
Std (Standard)  
Standard line speed  
Better noise immunity  
Rmt (Remote)  
Set Receiver to Remote Mode  
Per (Performance)  
Better line speed  
Type  
Poor noise immunity  
LEDs  
Power  
1/2/3  
State  
Steady  
Off  
Indication  
Power received  
Power off  
Steady  
Power Ethernet extension interface function is enabled  
No power is transmitted over Ethernet extension  
interface  
PoL  
PoE  
Off  
Steady  
Off  
Steady  
Powered device (PD) is connected  
Powered device (PD) is disconnected  
A valid Extender connection is established  
Fast  
Flashing  
Slow  
Flashing  
Off  
Data is being transmitted or received  
Link  
Extender port under negotiation mode  
Extender interface connection is not established  
Displays the link speed in Mbps  
Line  
Steady  
Speed  
PSE  
Output  
Steady  
All off  
PoE power can be transmitted for PD  
No PoE power can be transmitted for PD  
Steady  
Flashing  
Off  
Steady  
Off  
A valid Ethernet connection established  
Data transmitted or received  
Non-Ethernet connection is established  
Link speed at 100Mbps  
Green  
Yellow  
Link speed at 10Mbps  
User’s Manual  
3
10/100Base-TX Hardened PoL/PoE Ethernet Extender  
Power over Link (PoL) Enabled  
Distance Data Rate Receiver PoE Output  
300M  
400M  
600M  
800M  
1000M  
1200M  
100Mbps 30.0W  
90Mbps  
60Mbps  
45Mbps  
35Mbps  
20Mbps  
15.4W  
14.0W  
9.5W  
7.0W  
5.0W  
Power over Link (PoL) Disabled  
Power Supply Applied on Receiver  
Distance  
1400M  
1600M  
1800M  
Data Rate Receiver PoE Output  
15Mbps  
10Mbps  
3Mbps  
30.0W  
30.0W  
30.0W  
30.0W  
Up to 2200M 1Mbps  
<Note> The Reference Performance is tested on 24AWG Telephone wire (0.5mm  
diameter, 1-pair wire, Cable impedance: 100ohm).  
10/100Base-TX and Ethernet Extender Connectors  
10/100Base-TX Connection  
The following table lists the pinouts  
of the 10/100Base-TX RJ-45 port.  
Pin Regular Port  
PoE Port  
Output Transmit Data + Output Transmit Data +  
Output Transmit Data - Output Transmit Data -  
1
2
3
4
5
6
7
8
Input Receive Data +  
Input Receive Data +  
Positive (VCC+)  
Positive (VCC+)  
Input Receive Data -  
Input Receive Data -  
Negative (VCC-)  
Negative (VCC-)  
User’s Manual  
4
10/100Base-TX Hardened PoL/PoE Ethernet Extender  
Ethernet Extender Connection  
The RJ-11 and Terminal Block port pinouts:  
Pin 3: Tip, Pin 4: Ring.  
Use a telephone line to connect two  
RJ-11 or Terminal Block ports between  
two Hardened Ethernet Extenders.  
Functional Description  
Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity  
for industrial environment.  
Ethernet port: Supports IEEE802.3/802.3u/802.3x. Auto-negotiation:  
10/100Mbps, full/half-duplex; Auto MDI/MDIX.  
Auto data rate negotiation for the Ethernet extension interface.  
Supports six speeds with speed indicator LEDs on the front panel of the  
unit, up to 100Mbps @ about 300 meters (984 ft.), down to 1Mbps @  
about 2,200 meters (7,218 ft.).  
Supports Power over Ethernet applications up to 1,200meters (3,937ft.)  
for Max. 5 watts power consumed PoE powered devices.  
Power consumption:  
-
-
Enable Power over Link (PoL) function: Max. 65 Watts  
Disable Power over Link (PoL) function: Transmitter: Max. 5 W.  
Receiver: Max. 35 W with PoE output, Max. 5 W without PoE  
output.  
Power Supply: Redundant T:46-57V / R:46-57V DC Terminal Block  
power inputs and 48 VDC Latched DC JACK interface.  
Operating temperature range @ -40 to 75 (-40to 167). Tested  
for functional operation @ -40 to 85 (-40to 185).  
Supports Din-Rail or Panel Mounting installation.  
User’s Manual  
5
10/100Base-TX Hardened PoL/PoE Ethernet Extender  
Preface  
This manual describes how to install and use the Hardened Ethernet  
Extender. The Hardened Ethernet Extender introduced here provides one  
channel for Ethernet over existing voice grade copper wire.  
The Hardened Ethernet Extender fully complies with IEEE802.3 10Base-T  
and IEEE802.3u 100Base-TX standards.  
In this manual, you will find:  
Product overview  
Features on the Hardened Ethernet Extender  
Illustrative LED functions  
Installation instructions  
Specifications  
User’s Manual  
6
10/100Base-TX Hardened PoL/PoE Ethernet Extender  
Table of Contents  
Quick Start Guide............................................................................. 1  
Installation........................................................................................ 1  
Physical Description........................................................................ 2  
The Port Status LEDs and Power Inputs ..................................... 2  
10/100Base-TX and Ethernet Extender Connectors................... 4  
Functional Description.................................................................... 5  
Preface ................................................................................................ 6  
Table of Contents .............................................................................. 7  
Introduction ....................................................................................... 8  
Product Overview ............................................................................ 8  
Product Features ............................................................................. 8  
Packing List...................................................................................... 9  
One-Channel Hardened Ethernet Extender............................... 10  
Ports................................................................................................ 10  
Ethernet Extender Mode Settings.................................................. 10  
DIP Switch...................................................................................... 10  
Front Panel & LEDs...................................................................... 11  
LED Indicators ............................................................................ 11  
10/100Base-TX and Ethernet Extender Connectors................. 12  
Installation ....................................................................................... 13  
Selecting a Site for the Equipment................................................ 13  
DIN Rail Mounting ........................................................................ 13  
Connecting to Power ..................................................................... 15  
Redundant DC Terminal Block Power Inputs........................... 15  
48VDC DC Jack.......................................................................... 15  
Specifications ................................................................................... 17  
User’s Manual  
7
10/100Base-TX Hardened PoL/PoE Ethernet Extender  
Introduction  
The Hardened Ethernet Extender provides one channel for Ethernet over  
existing voice grade copper wire. This Hardened Ethernet Extender solution  
works in industrial applications or rugged environments.  
Product Overview  
Transmitter  
Receiver  
Product Features  
Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity  
for industrial environment.  
Ethernet port: Supports IEEE802.3/802.3u/802.3x. Auto-negotiation:  
10/100Mbps, full/half-duplex; Auto MDI/MDIX.  
Auto data rate negotiation for Ethernet extension interface.  
Support six speeds with speed indicator LEDs on front panel of unit, up  
to 100Mbps @ about 300 meters (984 ft.), down to 1Mbps @ about  
2,200 meters (7,218 ft.).  
User’s Manual  
8
10/100Base-TX Hardened PoL/PoE Ethernet Extender  
Supports Power over Ethernet applications up to 1,200 meters (3,937ft.)  
for Max. 5 watts of power consumed by PoE powered devices.  
Power consumption:  
-
-
Enable Power over Link (PoL) function: Max. 65Watts  
Disable Power over Link (PoL) function: Transmitter: Max. 5W.  
Receiver: Max. 35W with PoE output, Max. 5W without PoE output.  
Power Supply: Redundant T:46-57V / R:46-57V DC Terminal Block  
power inputs and 48 VDC Latched DC JACK interface.  
Operating temperature range @ -40 to 75 (-40to 167). Tested  
for functional operation @ -40 to 85 (-40to 185).  
Supports Din-Rail or Panel Mounting installation.  
Packing List  
Your package should contain the following items. IIf anything is missing or  
damaged, contact Black Box Technical Support at 724-746-5500 or  
The Hardened Ethernet Extender  
User’s Manual  
AC to DC Power Adapter and Power Cable (optional)  
User’s Manual  
9
10/100Base-TX Hardened PoL/PoE Ethernet Extender  
One-Channel Hardened Ethernet Extender  
Ports  
The Hardened Ethernet Extender provides TX ports and one Ethernet  
Extender port.  
For the TX ports, it uses RJ-45 connectors and auto senses the speed of  
10/100 Mbps.  
For the Ethernet Extender port, it uses RJ-11 and Terminal Block  
connectors  
and  
auto  
senses  
the  
speed  
of  
Link  
(below  
20)/20/40/60/80/100Mbps.  
Ethernet Extender Mode Settings  
Ethernet Extender mode settings are simple using a DIP (Dual Inline  
Package) switch on the top panel of the Hardened Ethernet Extender.  
DIP Switch  
DIP  
Down  
Up  
Switch  
Transmitter  
PoL Disable Power over Link  
Std (Standard)  
Type Standard line speed  
Better noise immunity  
Receiver  
Enable Power over Link  
Per (Performance)  
Better line speed  
Poor noise immunity  
Loc (Local)  
Set Receiver to Local Mode  
Std (Standard)  
Standard line speed  
Better noise immunity  
Rmt (Remote)  
Mode  
Set Receiver to Remote Mode  
Per (Performance)  
Better line speed  
Type  
Poor noise immunity  
User’s Manual  
10  
10/100Base-TX Hardened PoL/PoE Ethernet Extender  
Front Panel & LEDs  
LED Indicators  
The LED indicators give you instant feedback on the status of the Hardened  
Ethernet Extender:  
LEDs  
Power  
1/2/3  
State  
Steady  
Off  
Indication  
Power received  
Power off  
Power Ethernet extension interface function is  
enabled  
No power is transmitted over Ethernet  
extension interface  
Powered device (PD) is connected  
Powered device (PD) is disconnected  
A valid Extender connection established  
Steady  
Off  
PoL  
PoE  
Steady  
Off  
Steady  
Fast  
Flashing  
Slow  
Flashing  
Off  
Data transmitted or received  
Link  
Extender port under negotiation mode  
Extender interface connection is not established  
Displays the link speed in Mbps  
Line  
Speed  
Steady  
PSE  
Output  
Steady  
All off  
PoE power can be transmitted for PD  
No PoE power can be transmitted for PD  
A
valid Ethernet connection  
Steady  
Flashing  
Off  
established  
Data transmitted or received  
Non-Ethernet  
established  
Green  
Yellow  
connection  
is  
Steady  
Off  
Link speed at 100Mbps  
Link speed at 10Mbps  
Power over Link (PoL) Enabled  
Distance Data Rate Receiver PoE Output  
300M  
400M  
600M  
800M  
1000M  
1200M  
100Mbps 30.0W  
90Mbps  
60Mbps  
45Mbps  
35Mbps  
20Mbps  
15.4W  
14.0W  
9.5W  
7.0W  
5.0W  
User’s Manual  
11  
10/100Base-TX Hardened PoL/PoE Ethernet Extender  
Power over Link (PoL) Disabled  
Power Supply Applied on Receiver  
Distance  
1400M  
1600M  
1800M  
Data Rate Receiver PoE Output  
15Mbps  
10Mbps  
3Mbps  
30.0W  
30.0W  
30.0W  
30.0W  
Up to 2200M 1Mbps  
<Note> The Reference Performance is tested on 24 AWG Telephone wire (0.5 mm  
diameter, 1-pair wire, Cable impedance: 100 ohm).  
10/100Base-TX and Ethernet Extender Connectors  
10/100Base-TX Connection:  
The following table lists the pinouts  
of a 10/100Base-TX RJ-45 port.  
Pin Regular Port  
PoE Port  
Output Transmit Data + Output Transmit Data +  
Output Transmit Data - Output Transmit Data -  
1
2
3
4
5
6
7
8
Input Receive Data +  
Input Receive Data -  
Input Receive Data +  
Positive (VCC+)  
Positive (VCC+)  
Input Receive Data -  
Negative (VCC-)  
Negative (VCC-)  
Ethernet Extender Connection  
The RJ-11 and Terminal Block port pinouts:  
Pin 3: Tip, Pin 4: Ring.  
Use a telephone line to connect two  
RJ-11 or Terminal Block ports between  
two Hardened Ethernet Extenders.  
User’s Manual  
12  
10/100Base-TX Hardened PoL/PoE Ethernet Extender  
Installation  
This chapter gives step-by-step installation instructions for the Hardened  
Ethernet Extender.  
Selecting a Site for the Equipment  
As with any electric device, you should place the equipment where it will not  
be subjected to extreme temperatures, humidity, or electromagnetic  
interference. Specifically, the site you select should meet the following  
requirements:  
The Surrounding Air temperature should be between -40 to +167 degrees Fahrenheit  
(-40 to +75 degrees Celsius).  
The relative humidity should be less than 95 percent, non-condensing.  
Surrounding electrical devices should not exceed the electromagnetic field (RFC)  
standards.  
Make sure that the equipment receives adequate ventilation. Do not block the  
ventilation holes of the equipment.  
The power outlet should be within 6 feet (1.8 meters) of the product.  
DIN Rail Mounting  
Fix the DIN rail attachment plate to the back panel of the Hardened Ethernet  
Extender.  
Installation: Place the Hardened Ethernet Extender on the DIN rail from  
above using the slot. Push the front of the Hardened Ethernet Extender  
toward the mounting surface until it audibly snaps into place.  
Removal: Pull out the lower edge and then remove the Hardened Ethernet  
Extender from the DIN rail.  
User’s Manual  
13  
10/100Base-TX Hardened PoL/PoE Ethernet Extender  
User’s Manual  
14  
10/100Base-TX Hardened PoL/PoE Ethernet Extender  
Connecting to Power  
Redundant DC Terminal Block Power Inputs or 48-VDC DC Jack:  
Redundant DC Terminal Block Power Inputs  
Two pairs of power inputs can be used to power up this device. You only  
need to have one power input connected to run the Hardened Ethernet  
Extender.  
Step 1: Connect the DC power cord to the pluggable terminal block on the Hardened  
Ethernet Extender, and then plug it into a standard DC outlet.  
Step 2: Disconnect the power cord if you want to shut down the Hardened Ethernet  
Extender.  
48VDC DC Jack  
Step 1: Connect the supplied AC to DC power adapter to the receptacle on the top side of  
the Hardened Ethernet Extender.  
Step 2: Connect the power cord to the AC to DC power adapter and attach the plug to a  
standard AC outlet with the appropriate AC voltage.  
User’s Manual  
15  
10/100Base-TX Hardened PoL/PoE Ethernet Extender  
Power Input Assignment  
Power1  
48VDC  
DC Jack  
T:46-57V / R:46-57V DC  
Power Ground  
T:46-57V / R:46-57V DC  
Power Ground  
Power2  
Terminal  
Block  
Power3  
Earth Ground  
User’s Manual  
16  
10/100Base-TX Hardened PoL/PoE Ethernet Extender  
Specifications  
IEEE802.3 10Base-T, IEEE802.3u 100Base-TX  
10/100Mbps Ethernet ports with RJ-45 connectors  
Applicable Standards  
Fixed Ports  
1 x Ethernet Extender port with RJ-11 and Terminal  
Block connectors  
Speed  
10Base-T  
10/20Mbps for half/full-duplex  
100Base-TX  
Ethernet Extender  
100/200Mbps for half/full-duplex  
Link (Below 20), 20, 40, 60, 80, 100Mbps  
Switching Method  
Forwarding rate  
Cable  
Store-and-Forward  
14,880/148,810pps for 10/100Mbps  
10Base-T  
100Base-TX  
Ethernet Extender  
4-pair UTP/STP Cat. 3, 4, 5 up to 100m  
4-pair UTP/STP Cat. 5 up to 100m  
Telephone wires  
LED Indicators  
Per Unit (3 LEDs)- Power1, Power2, Power3  
Transmitter-  
PoL; Line Speed (Mbps): Link, 20, 40, 60, 80, 100  
Receiver-  
PoE; Line Speed (Mbps): Link, 20, 40, 60, 80, 100; PSE  
Output (Watts): 5, 15, 30  
Dimensions  
Weight  
50mm (W) 110mm (D) x 135mm (H)  
(1.97” (W) x 4.33” (D) x 5.31” (H))  
0.77Kg (1.7lbs.)  
Terminal Block: T:46-57V / R:46-57V DC  
DC Jack: 48VDC, External AC/DC required  
Terminal Block & DC Jack Power Inputs: 2.5A @  
48VDC (Peak current 3.26A)  
Power  
Power Consumption  
Enable PoL: Max. 65Watts  
Disable PoL:  
Transmitter: Max. 5W  
Receiver: Max. 35W with PoE output  
Max. 5W without PoE output  
User’s Manual  
17  
10/100Base-TX Hardened PoL/PoE Ethernet Extender  
Operating Temperature  
-40~ 75(-40~ 167)  
Tested for functional operation @  
-40~ 85(-40~ 185)  
Storage Temperature  
-40~ 85(-40~ 185)  
5 ~ 95%, non-condensing  
FCC Part 15, Class A  
Humidity  
EMI  
EN61000-6-4: EN55022, EN61000-3-2, EN61000-3-3  
EN61000-6-2:  
EN61000-4-2 (ESD Standard)  
EMS  
EN61000-4-3 (Radiated RFI Standards)  
EN61000-4-4 (Burst Standards)  
EN61000-4-5 (Surge Standards)  
EN61000-4-6 (Induced RFI Standards)  
EN61000-4-8 (Magnetic Field Standards)  
IEC60068-2-6 Fc (Vibration Resistance)  
IEC60068-2-27 Ea (Shock)  
Environmental Test  
Compliance  
IEC60068-2-32 Ed (Free Fall)  
User’s Manual  
18  
Black Box Tech Support: FREE! Live. 24/7.  
Tech support the  
way it should be.  
Great tech support is just 30 seconds away at 724-746-5500  
or blackbox.com.  
About Black Box  
Black Box provides an extensive range of networking and infrastructure products.  
You’ll find everything from cabinets and racks and power and surge protection  
products to media converters and Ethernet switches all supported by free, live  
24/7 Tech support available in 30 seconds or less.  
© Copyright 2013. Black Box Corporation. All rights reserved. Black Box® and the Double Diamond  
logo are registered trademarks of BB Technologies, Inc. Any third-party trademarks appearing in  
this white paper are acknowledged to be the property of their respective owners.  
LBPS310A-KIT, version 1  

Glen Dimplex Home Appliances Ltd 121R User Manual
Gateway FPD 1540 User Manual
Garland 7000 User Manual
Frigidaire 318200612 User Manual
Fostex PD 6 User Manual
Eizo LA 130 D User Manual
Eizo EIZO FlexScan L352T C User Manual
Celluon LASERKEY CL800BT User Manual
Asus P8b75 M Lx Plus Desktop Motherboard P8B75 M LX PLUS User Manual
Ampro Corporation COM 830 User Manual