Dishwasher
D 5001 E
Instruction Manual
D 5001 ES
D 5001 EM
D 5001 EX
TABLE OF CONTENTS
1 Getting To Know Your Machine 3 5 Program Selection and Operat
View of the Machine
Technical Specifications
3
4
ting Your Machine
Button and Button Descriptions
Program Selection
Adding Functions to the Program
Program Steps Follow-up
Canceling a Program
Changing a Program
Programming the Delayed Start
Usage of Child Lock
Salt Indicator
21
22
23
23
23
23
24
24
25
25
25
25
26
27
2 Safety Instructions
Before Installation
Before First Use
Child Safety
For daily operation
Problems
4
4
4
4
5
5
What should not be washed in your
dishwasher
Rinse Aid Indicator
5
Rinse Aid Indicator Setting
Starting Your Machine
Programme Table
3 Directions for Assembly
Safety notes for installation
Installing Your Dishwasher
Water connection
Connect water inlet hose
Water drainage
6
6
6
7
7
8
8
8
6 How to clean your dishwasher 28
Cleaning the filters
Cleaning the spray arms
28
29
Electrical connection
Disposal
7 Troubleshooting:
What to do if the dishwasher will not
run
The cleaning results are
unsatisfactory
30
30
4 Using Your Dishwasher
Filling the dishwasher salt
When operating for the first time:
Filling the Rinse Aid Dispenser
Filling the Detergent Dispenser
Detergent
Multipurpose Detergents
Loading the dishwasher
Suggestions for loading the
dishwasher
9
9
30
36
10
11
11
12
13
13
Service
14
Loading suggestions
18
1
Getting To Know Your Machine
View of the Machine
��
�
�
�
��
�
��
�
�
�
�
�
1. Upper dish basket with shelf
2. Guide rail for the upper dish
basket
��
3. Salt container
4. Cutlery basket
5. Detergent dispenser
6. Door
7. Control panel
8. Filters
9. Lower sprayer arm
10. Lower basket
11. Upper sprayer arm
12. Housing (depends on the model)
13. Turbo fan heat drying system
(depends on the model)
3
GB
improve our products, we may change
our specifications and designs without
prior notice.
Technical Specifications
Permitted water pressure: 0,3 –10
bar (= 3 – 100 N/cm² = 0,01-1,0Mpa)
Electrical connection: 220-240 Volts,
10 Amps (see type plate)
Note for Testing Institutes
The necessary information for
performance testing will be provided
upon request. The request can be
done by e-mail through:
Please do not forget to write the model
code and stock code information of
the appliance besides your contact
information in the e-mail. The model
code and stock code information can
be found on the rating label, which is
placed on the side of the door.
Output: 1900-2200 W
Heat output: 1800 W
This device corresponds to the
following EU directives:
2006/95/EC: Low Voltage Directive
2004/108/EC: EMV Directive
DIN EN 50242: Electrical dishwasher
for home use Testing procedures for
practical service conditions
Because we continually strive to
2
Safety Instructions
disconnected from the mains
during installation.
Before Installation
Check the appliance for transit
damage. Never install or use damaged
machines. If in doubt, contact your
supplier.
•
The appliance must not be
connected to the mains using
an extension cable. Extension
cables do not provide the
necessary safety (e.g. danger of
overheating).
Always use the original plug
delivered with the appliance.
The plug must be freely accessible
after the appliance has been
installed.
Before First Use
•
See Notes for Installation on page
6.
•
•
•
Have the grounding system
installed by a qualified electrician.
The manufacturer cannot be held
liable for any damage caused by
operating the appliance without
proper grounding.
Child Safety
•
Do not allow children to play with
•
•
Before operating the system,
please check that the information
on the type plate corresponds to
the information on your power
supply.
the appliance.
•
Dishwasher detergents are caustic
and may cause injury to the eyes,
mouth and throat. Please note the
safety instructions provided by the
The dishwasher must be
4
GB
manufacturers of the detergents.
Never leave children unsupervised
while the appliance is open, as
the appliance may still contain
detergent leftovers.
The water in the dishwasher is not
drinking water. Danger of caustic
injuries.
Always place long and sharp/
pointed objects (e.g. serving forks,
bread knives) into the cutlery
basket with the pointed end down
or flat on the upper basket to avoid
possible injuries.
the plug. Turn off the water supply
tap.
•
What should not be washed in
your dishwasher
•
•
•
•
Rust sensitive steel parts
Cutlery with wooden or horn
handles
Cutlery with mother of pearl or
porcelain handles
Non heat resistant plastic parts
No glued dish or cutlery parts
No items made out of copper, tin
or aluminium
•
•
•
•
•
Sensitive decorative glasses and
porcelain parts
Lead crystal glasses
Art and crafted articles
Aluminium and silver tend to
discolour
Glass and crystal articles may lose
their shine over time
For daily operation
•
•
•
•
•
Use your appliance only for the
following domestic uses: Washing
household dishes.
Do not use chemical solvents in
the appliance; there is a danger of
explosion.
Do not sit or stand on the opened
door or place other objects on it.
The appliance may tip over.
Do not open the door while the
appliance is running, as hot water
or steam may escape.
•
•
•
•
•
Sponges and dishcloths
Note
Do not wash items soiled with cigarette
ash, candle wax, varnish, paints or
chemicals.
Do not leave the door open – an
open door can be a hazard.
Recommendation:
When buying new dishes, note whether
they are suitable for the dishwasher.
(marked as dishwasher proof)
Problems
•
Repairs and modifications to the
appliance may only be carried
out by qualified customer service
personnel.
•
In the event of a problem, or
before performing a repair,
disconnect the appliance from the
mains supply:
- disconnect the appliance by
pulling out the mains plug
- shut off the power.
•
Do not pull on the cable – pull on
5
GB
3
Directions for Assembly
Safety notes for installation
Prior to installing and using your
appliance, please check it for possible
transit damage.
Installing Your Dishwasher
•
Choose a suitable location for your
dishwasher. Take care to ensure
that the appliance is stable on a
level surface.
If the appliance is damaged, please
contact your supplier.
•
Unevenness in the floor can be
equalised by adjusting the screw
feet. When the appliance is
standing correctly, the door can be
closed without difficulty.
Never install or use a damaged
appliance.
•
•
Water inlet and drainage hoses
must be positioned so that they
can move freely without bending
or squeezing.
The appliance may not be installed
in a room where the temperature
is below 0° Celsius.
The following directions must be
followed to connect the dishwasher
properly.
•
Before operating your dishwasher,
please ensure that the information
on the type plate corresponds to
the current and voltage of your
power supply.
•
The appliance may only be
connected using a properly
grounded socket. Ensure that the
appliance is grounded according
to regulations.
•
•
The grounded socket must be
easily accessible and close to the
appliance.
Do not use extension cables or
multiple adapters, as this can lead
to overheating, which can be a fire
hazard.
•
•
Hardwiring may only be carried out
by a qualified electrician.
Check the power cable, the
water inlet hose and the drainage
hose. Damaged parts may only
be replaced by customer service
personnel or by a qualified
electrical service expert.
6
GB
tap with a ¾ inch external thread. If
required, use a filter insert to filter
deposits from the pipes.
Water connection
•
There are two different types of
water inlet hoses:
- Cold water inlet hose (up to
25°C)
- Hot water inlet hose (up to
60°C)please check which one is
applicable to your model.
Check that the connection does not
leak.
Important
For safety reasons, turn off the tap
after every rinse process.
If you are willing to connect
your machine to natural
energy resources or to the central
hot water supply, first check out
whether your water inlet hose
type is suitable by checking the
temperature values written on the
hose. If your hose is not suitable,
apply to your authorized service to
change the hose.
The dishwasher may not be
connected to open warm water
devices or flow-through water
heaters.
AQUASAFE+ (some models)
The Aquasafe+ System protects
against water damage hich may be
caused at the water inlet hose.
•
Do not immerse the system’s valve
box into water; it contains electrical
components.
Permitted water pressure:
Lowest permitted water pressure: 0.3
bars = 3 N/cm² = 30 kPa
When the water pressure is below 1
bar, please contact your technician.
In case of damage, pull out the power
supply plug.
Do not shorten or lengthen the hose
insert as it contains electrical cables
and components.
Highest permitted water pressure: 10
bar = 100N/cm² = 1Mpa
When the water pressure is above 10
bars, a pressure reduction valve must
be installed (available in trade supply
stores).
����
������
Connect water inlet hose
Ensure that the water inlet hose is not
bent or squeezed. Do not install a used
hose set.
���������
Use a screw-on hose connector to
connect the water inlet hose to a water
7
GB
Extension hoses
Water drainage
If a hose extension is required, a
drainage hose of equal quality must be
used.
Connecting the drainage hose.
Take care to ensure that the drainage
hose is not bent or squeezed.
The maximum length must not exceed
4m. Using a longer hose will produce
poorer cleaning results.
Check that the drainage hose is firmly
seated.
Siphon connection
����������
The drainage height must be between
50 and 100cm above the floor.
Use hose clamps to fasten the
drainage hose to the siphon.
���������
�������
Electrical connection
Please refer to the type plate for
information on current type, mains
voltage, and fuse protection.
The type plate is located on the inside
of the door.
The mains plug must be freely
accessible after installation.
Power cables and insulated cables
must not be accessible (exposed) after
installation.
Disposal
Packaging
The packaging and some parts of your
appliance are made from recyclable
materials. These materials are marked
with the recycling symbol and the
relevant material type (PE, PS, POM).
Before operating your appliance,
remove the packaging material and
dispose of it in accordance with
regulations.
8
GB
Warning
the product, it’s packaging or in the
manual.
Packaging materials may be
dangerous to children.Reusable
substances may be dropped off at your
local disposal facilities. You may obtain
further information from your local
authorities and disposal facilities.
Materials used are recyclable
according to their labelling. Reuse,
recycling of materials and further
reutilization of used products are
important contributions to protect our
environment.
Used appliances –
Environmental notice
This product must not
be disposed of with your
Please ask your local town council for
the nearest collection point.
regular household waste.
Instead, you need to dispose of the
waste equipment by handing it over
to a designated collection point for
the recycling of waste electrical
and electronic equipment. This is
indicated by a symbol to be found on
To avoid possible dangers, disable
your waste appliance prior to
discarding it. Pull the mains plug and
cut the power cord. Disable any door
locks.
4
Using Your Dishwasher
Important
in water easily and will damage the
softening device.
The electricity and water connections
of the dishwater must be in compliance
with the instructions in this booklet.
Remove the lower basket from the
appliance.
Filling the dishwasher salt
Important
Only use special dishwasher salt in
your appliance.The manufacturer is
not liable for damage resulting from the
use of the wrong type of salt.
Open the screw-in cap of the salt
container by turning it counter
clockwise (fig. A,B).
Do not use coarse-grained salt. Small
grains or powdered salt is more easily
soluble. Never use culinary or table
salt. These types of salt do not dissolve
9
GB
When operating for the first
�
time:
Pour 1 litre of water into the salt
container (Fig. C).
Pour the salt into the container with the
aid of the salt funnel provided (Fig. D).
Pour in enough salt to fill the container.
The container holds approx. 2 kg.
To speed up the rate of dissolution of
salt in water, stir it with a spoon.
�
Close the cap tightly.
Begin a washing program immediately
after filling the salt container. The
washing program prevents damage to
the appliance which may be caused by
any spilled salt solution. After the first
washing cycle, the salt level indicator
light will go out.
�
Important
Depending on the particle sizes of
different salt brands in the market,
tablet properties and water hardness,
dissolution of the salt in water may take
a couple of hours.
So, the salt indicator continues lighting
for a while after filling salt into the
machine. (For models with a salt
indicator)
�
10
GB
Filling the Rinse Aid
Dispenser
Rinse aids allow washing water to
rinse off more cleanly and prevent
watermarks or streaks on the dishes.
Only use rinse aid designed for use in
dishwashers.
Note
�
If you use “2 in 1” or “3 in 1“ detergents
/ tablets, you do not need an additional
rinse aid.
Open the rinse aid dispenser by
pressing the locking lever (B)
�
Carefully pour in rinse aid to the MAX
mark. Close the lid until it clicks (3).
Carefully wipe off spilled rinse aid.
Excessive rinse aid causes excessive
foam formation, which may hinder
cleaning.
Set the dose of rinse aid
�
The dose of rinse aid to be used can
be set by means of the dispenser
regulator (between levels 1 and 6) (4).
Your appliance is pre-set at the factory
to level 3.
Filling the Detergent
Dispenser
Note
Only use detergents formulated for use
in dishwashers.
Only change the setting if the following
applies after washing:
Open the detergent container by
pushing the locking lever to the right
(A).
•
•
Watermarks are visible on the
dishes: Set dosage higher
Streaks are visible on the dishes:
Set dosage lower
The lines on the inside of the detergent
container will help you measure the
correct amount of detergent.
The detergent container holds a total of
40 cm³ of detergent (1).
11
GB
When the dishwasher is fully loaded
and the dishes are very dirty, we
recommend filling the detergent
container up to the 25 cm³ mark. When
the dishes are less dirty, it is generally
sufficient to fill the detergent up to the
15 cm³ mark.
Detergent
Please use detergents produced
specially for the dishwashers in your
machine.
Keep the opened detergent packages
in a cool and dry place where children
can not reach.
If your dishes have been in the
dishwasher for some time without
being washed, you should also fill the
small detergent container up to the line
(2).
Put the detergent into the detergent
dispenser just before operating the
machine.
Please contact the manufacturer to
get detailed information about the
detergent you are using.
The programme table shows the
amounts of detergent required for the
different wash programmes.
Always use powder detergents in
short programs without pre-washing.
Fill in the powder detergent into the
compartment nr. 2 with a grid cover
as shown in the picture and close the
detergent box lid. When completely
full, this compartment will contain 6 g
of powder detergent.
These may differ according to how dirty
the dishes are and the water hardness
in your location.
�
Do not use tablet detergents in short
programs since the solubility of them
changes depending on the temperature
and time.
In programs with pre-washing and high
temperature, in which you may use
tablet detergents, make sure that the
detergent box lid is closed firmly.
Excessive usage of powder detergents
can cause the detergent not dissolve
completely and can also cause
scratches on the glassware.
�����
�
����
�����
�
12
GB
Make sure that salt and rinse aid
compartments are full.
Multipurpose Detergents
The best washing results in
dishwashers is obtained by using
detergent, rinse aid and water
softening salt individually.
Set the water hardness to its highest
degree and perform an empty run.
After the empty washing review the
user manual and readjust the water
hardness level so as to suit your water
supply.
New products of the detergent
producers what they call as
“Multipurpose Detergent” can act as
water softening salt and/or rinse aid
in addition to acting as a detergent.
Some types of these detergents can
also contain special-purpose washing
chemicals such as glass and stainless
steel protectors.
Make the appropriate rinse aid
settings.
Depending on the model, salt indicator
and/or rinse aid indicator should be
enabled again if they are disabled
before.
Multipurpose detergents commonly
found in the market:
2in1: Those contain detergent, rinse
aid or water softening salt.
Loading the dishwasher
General:
3in1: Those contain detergent, rinse
aid and water softening salt.
4in1: Those containing glass protectors
in addition to detergent, rinse aid and
water softening salt.
5in1: Those containing glass and
stainless steel protectors in addition
to detergent, rinse aid and water
softening salt.
Before you load the dishwasher with
dishes
•
•
Remove coarse food leftovers
Place all containers such as
cups, glasses and pots into the
machine with the opening facing
downwards (so that no water can
collect)
•
Dishes and cutlery may not be
placed above each other
Glasses may not touch
The movement of the spray arms
must not be hindered
Multipurpose detergents give satisfying
results only under certain usage
conditions. Observe the instructions
of the detergent manufacturer on the
package when using such detergents.
•
•
•
•
•
Place all large and very dirty items
in the lower basket.
Small and light items can go into
the upper basket.
Long and narrow items are placed
in the middle of the baskets.
Contact the detergent producer if your
dishes are wet and/or if you notice lime
spots particularly on your glasses after
the washing program is over.
When you give up using such
detergents:
13
GB
Attention
4 folding plate support rods
Knives and other utensils with sharp
tips and edges must be placed
horizontally into the upper basket due
to risk of injury.
(depending on the model)
There are four separate “folding plate
support rods” in the lower basket of
your dishwasher designed to allow
you more space to accommodate
saucepans and large bowls in the
lower basket. You can either fold each
section (1, 2, 3, 4) individually or, all at
once, to create a large empty space.
Simply press the handgrips (A) and
fold them down”
Please do not overload your
dishwasher and pay attention to the
notes regarding dishes which are
suited to the dishwasher.
Only in this manner will you obtain
optimal washing results with a sensible
use of energy.
�
�
Suggestions for loading the
dishwasher
Use the lower basket for plates, bowls,
pots etc.
�
�
�
14
GB
2 folding plate support rods
(depending on the model)
�
�
There are four separate “folding plate
support rods” in the lower basket of
your dishwasher designed to allow
you more space to accommodate
saucepans and large bowls in the
lower basket. You can either fold each
section (1, 2) individually or, all at once,
to create a large empty space.
Simply press the handgrips (A) and
fold them down”
�
Bottle holder
(depends on some models)
For cleaning your bottles. To remove,
pull the holders apart in opposite
directions (H).
�
15
GB
Variable cutlery basket
(depending on the model)
The variable cutlery basket can be
separated into 3 parts depending on
the amount of cutlery and the degree
of dirtiness.
Small cutlery basket sections also fit
into the upper basket.
To do this, turn the lock on the handle
to the right (A).
�
Pull the smaller cutlery basket upwards
and out of its holders (B).
�
To put the parts together again,
proceed in the opposite direction.
�
Use the basket inset (C) for your
cutlery so that all items in the basket
are surrounded by a sufficient water
flow.
For larger items (e.g. wire whisks), the
basket inset may be removed (C).
To make loading easier, the cutlery
basket can be removed.
Place long items such as ladles,
cooking spoons etc. on the rack in the
upper basket.
16
GB
Basket insert with variable height
settings
(depending on some models)
You can also use this insert in the
lower basket for glasses and long-
handled cutlery / utensils.
If you do not need the insert, fold the
rack upwards at the angle shown (A).
Push the entire insert upwards (B).
Place the insert in the upright position
(C). Push the insert downwards and
lock it into place with the holder (D).
When you want to use the basket
again, reverse the procedure.
�
�
To set the height, push the rack
upwards and fold it open in position
(G).
�
�
When finished, check that the sprayer
arm can still move freely.
�
�
�
�
�
17
GB
Loading suggestions
Load the upper basket with dessert
plates, cups, glasses etc.
Upper basket with variable height
setting
(depends on some models)
The upper basket is equipped with a
lifting mechanism which enables you
to change the height of the basket
without having to remove it from the
dishwasher, even if it is fully loaded.
The height of the upper basket was
set to its lowest position at the factory.
To lift the upper basket to the “high”
(A) position, hold it on one side and
carefully pull it upwards. To lift the
opposite side of the basket, hold it and
pull it upwards in the same manner (A).
�
�
To lower the upper basket, hold the
basket lever on one side and carefully
lower the basket without releasing the
lever (B). Repeat the procedure with
the lever on the opposite side of the
basket. Make sure that both levers
catch at the same height.
�
18
GB
Height setting with empty basket
(depends on the model)
In this model, the height setting of the
upper basket may be changed using
the wheels which are mounted at two
different heights.
Release the latches on both the right
and left tracks of the upper basket by
pushing them outwards (C).
�
�
�
Pull out the basket out completely (D).
Place the basket back into the tracks at
the desired height (E).
Push the latches back into the correct
position.
Rack
(depends on the model)
Depending on the size of the glasses
and cups, the rack height setting may
be adjusted (C, D, E).
�
�
�
19
GB
Glass Support
(depends on the model)
When placing the glasses or goblets
with a long grip, lean them against the
glass support, the edge of the basket
or the shelf but not against the other
pieces. Do not lean the long glasses
against each other, otherwise they do
not remain stable during washing cycle
and may get damaged.
When you need to place the bulky
pieces into the upper basket,
disconnect the lug of the glass support
from the bar of the basket where it is
attached to. Thus, you will acquire a
wider place.
Upper Basket Drawer
(depends on the model)
You can easily place additional desert
spoons, small forks and knives into the
drawer installed to the upper basket of
your machine.
20
GB
5
Program Selection and Operating Your Machine
�
�
�
�
�
�
�
� �
��
��
�� ��
��
��
��
�
�
�
�
��
1. On / Off Button
12. Delayed Start Indicator
13. Half Load (1/2) Indicator
14. Child Lock Indicator
15. Salt Indicator
2. Combi Tablet Button
3. Program Selection Button
4. Half Load Button
5. Display
16. Rinse Aid Indicator
6. Start/Pause/Cancel Button
17. Program Steps Follow-up Indicator
a Washing Step Indicator
b Rinsing Step Indicator
c Drying Step Indicator
7. Delayed Start Button
8. Combi Tablet Indicator light
9. Handle
10. Program Indicator
d End of Program Indicator
11. Remaining Time Indicator/Delay
Time Indicator
21
GB
programs can change depending on
the model you have purchased.
Button and Button
Descriptions
On / Off Button (1)
When you press the On/Off button,
the display switches on with the last
program used and it dims when you
turn the machine off.
Half Load Button (4)
If you want to run your machine without
loading it completely, place your dishes
into the machine as you desire. First,
press the On / Off Button (1). Select
the desired program and press the Half
Load (4) button. You must see the Half
If the Half Load (4), Extra Drying (5),
Child Lock (16), Combi Tablet (2)
and Delayed Start (13) functions are
enabled during the last program used,
these functions will remain active
when the machine is turned off and on
again. If you would like to disable these
functions after turning the machine
off and on again, you must press the
relevant buttons.
Load indicator (14)
appearing on
the screen. Start the program by
pressing the Start / Pause / Cancel
button (7). Thanks to the Half Load
option, you can use both lower and
upper baskets of your machine and
you can save water and energy.
Extra Drying Button (5)
(Depending on the model)
Start / Pause / Cancel Button (7)
It is used to start, pause or cancel the
selected program or the delayed start
countdown. The selected program will
start running when the Start / Pause /
Cancel button (7) is pressed.
Some washing programs provide
premium-drying performance. The
programs in which the extra drying
function can be enabled are indicated
in the Program Data and Table of
Average Consumption Values. Extra
drying
symbol lights up (15) on the
Wait for two seconds to view the full
display on the screen after you turn on
the machine by pressing the On/Off
button (1) before you press Start /
Pause / Cancel (7) button.
display when you select the extra
drying (5) function.
Combi Tablet Button (2)
Allows to obtain a better drying
performance from the multi-purpose
detergents called as all in one
detergents such as 2in1, 3in1, 4in1,
5in1 and etc., depending on the
hardness level of the tap water. The
programs in which the Combi Tablet
function can be enabled are indicated
in the Program Data and Table of
Average Consumption Values. Combi
Tablet indicator light (9) lights up when
you select the Combi Tablet function
(2).
Program Selection Button (3)
You can select the washing program
you want to use with the aid of the
“Program Data and Table of Average
Consumption Values” after pressing
the program selection button. Number
of the selected program appears in the
program indicator (11) on the display
(6) in the format of
Program number will increase by one
each time you press the program
.......
selection button. Number of the defined
22
GB
Delayed Start Button (8)
You will obtain a better drying
performance if you select the Combi
Tablet function in cases where you use
a multi-purpose detergent.
You can delay the start of the selected
program until 24 hours with increments
of 1 hour by means of the Delayed
Start Function.
To add a function to the program:
1. Select the program by pressing
program selection button (3).
2. Press the button of the function
that you want to enable and
check to see thee indicator for the
relevant function on the display.
3. You can start the program by
pressing the Start / Pause / Cancel
button (7).
Program Selection
You can select the desired program
after turning on the machine by
pressing the On / Off button (1).
Switch to the program you want to
operate by pressing program selection
button (3). You can follow up the
program you are in from the program
indicator (11) on the screen. Program
number will increase by one each time
you press the program selection button
(Number of the defined programs can
change depending on the model you
have hhhpurchased). The selected
washing program will start running
when the Start / Pause / Cancel
Program Steps Followtup
You can follow-up the step in which the
current program is in from the Program
Steps Follow-up indicator (19) on the
display.
a Washing Step Indicator (19 a)
b Rinsing Step Indicator (19 b)
c Drying Step Indicator (19 c)
d End of Program Indicator (19 d)
button (7) is pressed. Time indicator
(12) will start displaying the estimated
remaining time to the end of program.
The display shows the steps for
Total time can be different from
the time indicated at the beginning
since it can change while the
program is running, depending
on the temperature of the room
where your machine is installed,
temperature of the supply water,
autotcleaning of the water softening
system (regeneration) and amount
of the dishes.
washing 19 a, rinsing 19 b and drying
19 c, respectively, while the selected
program is running. Only the End of
Program indicator 19 d lights up when
the program is over. Remaining Time
Indicator (6) displays “00:00”.
Canceling a Program
Press Start / Pause / Cancel button ( 7)
for three seconds to cancel a program
that is already running. Release the
button when indicator and End of
Program Indicator (19 d) start flashing
above the program indicator (11) in the
display. For a couple of minutes the
machine will fulfill the necessary
Adding Functions to the
Program
With the help of the add function
buttons, you can run the selected
program together with the Half Load
(1/2) (4), Extra Drying (5), Combi
Tablet (2) and Delayed Start (8)
functions.
operations required for cancellation.
End of Program Indicator (19 d) starts
23
GB
lighting continuously when the program
cancellation is completed. You may
select and operate a new program
following the program cancellation
process. There might be residues of
detergent or rinse aid left in the
machine and/or on the pieces being
washed depending on the step the
previous program was in at the time of
such cancellation.
the delayed start button (8). Press the
Start / Pause / Cancel button (7) after
setting the time. The delayed start
indicator sand glass (13) will remain
lit on the display during the delayed
start countdown and the delay time
indicator (12) will display the remaining
time. Program will start automatically
when the countdown is over.
You can use the delayed start function
if you are utilizing the economic
electricity tariff.
Changing a Program
Press Start / Pause / Cancel button (7)
first to switch your machine into pause
mode if you want to change your
selection after you started the program.
Then, switch to the desired program
by pressing Program Selection
If you want to change the program
or functions while the delayed start
function is enabled, then pause the
machine by pressing the Start / Pause
/ Cancel button (7). You will see that
the countdown stops. Select the new
program and/or add the functions
as described in Program Selection
and Table of Average Consumption
Values. Resume the delayed start
countdown by pressing the Start /
Pause / Cancel button (7).
button (3). Start the new program
by pressing Start / Pause / Cancel
button (7) again. Your new selection
will resume operation from the step in
the previous program (For example,
if the previous program was in rinsing
step, the new one will also start from
the rinsing step). If you want to run
the newly selected program from the
very beginning, you have to apply the
program cancellation process first and
then select a new program.
If you want to cancel delayed start
countdown while it is in progress, then
press the Start / Pause / Cancel button
(7) for three seconds. Release the
button when indicator and End of
Program Indicator (19 d) start flashing
above the program indicator (11) in the
display. For a couple of minutes the
machine will fulfill the necessary
operations required for cancellation.
End of Program Indicator (19 d) starts
lighting continuously when the delayed
start countdown cancellation is
Programming the Delayed
Start
You can delay the start of the selected
program until 24 hours. Delayed start
can not be set after the program starts.
The selected program must not be
started in order to be able to set the
delay time.
completed. You may select and
operate a new program following the
delayed start countdown cancellation
process.
Delayed start indicator sand glass
(13) will start flashing when the
delayed start button (8) is pressed. You
can set the desired time by pressing
24
GB
If you want to select a new delayed
start time while the delayed start
countdown is in progress, then pause
the machine by pressing the Start /
Pause / Cancel button (7). Set the
desired time by pressing the Delayed
Start Button (8). Start the countdown
for the new time by pressing the Start /
Pause / Cancel button (7) again.
container when the rinse aid indicator
comes on.
WARNING:
If the Rinse Aid Indicator is set to
(OFF), rinse aid indicator will never
come on even if the rinse aid container
is empty.
Rinse Aid Indicator Setting
Usage of Child Lock
•
When your machine is switched
off, press Half Load ( ) button
(4) and then On / Off button (1) to
switch it on.
Press the Child Lock buttons ((3) and
(4) simultaneously for three seconds
in order to activate the child lock. Child
lock indicator (16) will appear on the
screen. Repeat the same procedure
to disable the child lock. Child lock
does not lock the door of the machine
but it prevents the selected program
or functions from being changed and
disables the Start / Pause / Cancel
button (2).
•
Hold Half Load ( ) button (4)
pressed and release On / Off
button (1).
•
•
Keep Half Load ( ) button (4)
pressed for three seconds more.
Rinse Aid Indicator (18) comes on
and the stored rinse aid indicator
status of your machine appears on
the display in the format of “ON” or
“OFF”.
Salt Indicator
•
You can change the status of the
indicator as “ON” or “OFF” with
Start / Pause / Cancel button (7).
If you switch off the machine with
“On/Off” button (1) when the status
is “ON”, then the rinse aid indicator
will come on when the rinse aid
level in your machine becomes
low while the machine is in use.
If you switch off the machine
with “On/Off” button (1) when the
status is “OFF”, then the rinse aid
indicator will never come on.
Please check the salt indicator (17)
on the display to see whether there is
enough softening salt in your machine
or not. You need to refill the powder
dispenser whenever the salt warning
indicator light lights.
WARNING:
If the water hardness level is stored
as (r1), salt indicator will never come
on even if the salt container is empty.
(Adjusting the water hardness level is
explained in Water Softening System
section.)
Rinse Aid Indicator
Check the rinse aid warning display
(18) on the screen to find out if there
is sufficient amount of rinse aid in your
machine. You must refill the rinse aid
25
GB
•
•
End of Program indicator (19 d)
will light up.
Turn off your machine by pressing
On / Off button (1).
Close the tap.
Unplug the mains plug from the
wall socket.
Leave your dishes in the machine
for about 15 minutes after they
are washed in order to have them
cooled down. Your dishes will dry
in a shorter time if you leave the
door of your machine ajar during
this period. This will increase
the drying effectiveness of your
machine.
Starting Your Machine
•
Plug the mains plug into the wall
socket.
•
•
•
•
Open the tap.
Open the door.
Place the dishes.
Check if the upper and lower
impellers rotate freely.
•
•
•
•
Put sufficient amount of detergent
in the detergent dispenser and
close its lid.
•
•
Press On/Off button.
Check if the salt and rinse aid
warning indicators (17,18) light
and add salt and/or rinse aid if
needed.
•
•
Determine your washing program
with the aid of the Program
Data and Table of Average
Consumption Values.
You can select the determined
washing program by pressing
program selection button (3).
You can see the program time in
the Remaining Time Indicator (6).
If necessary, you can change your
washing program as you prefer
by means of the Add Function
Buttons (4,5,2,8).
•
•
•
Start the program by pressing the
Start / Pause / Cancel button (7).
WARNING:
Pay attention not to open the door
of the machine when it is running.
Stop the machine by pressing Start /
Pause / Cancel button (7) if you have
to open the door. Then, open the door
of your machine. There may be a rush
of vapor when you open the door of
your machine; be careful. Close the
door and press Start/Pause/Cancel
button (7) again. Program will resume
running.
26
GB
27
GB
6
How to clean your dishwasher
Cleaning your machine at regular
intervals ensures longer product life
and reduces the risk of reccurring
problems.
Warning
Do not operate your dishwasher
without a filter. Ensure that your filters
are correctly installed. Clean the filters
regularly.
Warning
Always unplug the machine and turn
off the water supply before cleaning.
Use a gentle household cleaner for the
outside and the door seals. Clean the
control panel only with a moist cloth
and clear water.
�
�
Cleaning the filters
Clean the filters and the spray arms
regularly. A dirty machine will have a
negative effect on the cleaning results.
�
1. Main filter
2. Coarse filter
3. Micro filter
1. Remove the lower basket from the
machine.
2. Turn the coarse filter to the right
and pull it out in an upward
direction (A).
�
3. Pull out the main filter (B).
4. Press on the two tongues of the
coarse filter and remove the micro
filter (C).
5. Clean the filters thoroughly under
running water. Use a brush if
necessary.
�
6. Replace main fitler.
7. Replace the micro filter and the
coarse filter into the main filter.
Twist it clockwise until it clicks in.
�
28
GB
Cleaning the filter inset in the water
inlet hose (depending on the model)
Dirt from deposits in the water pipes is
prevented by a filter in the water inlet
hose. Check the filter and the water
inlet from time to time.
Cleaning the spray arms
Dirt or calcium residue may block the
nozzles on the spray arms. For this
reason, regularly check the spray
nozzles.
1. Lower spray arm
2. Upper spray arm
1. Close the water tap and unscrew
the water inlet hose.
2. Take out the filter and clean it
under running water.
1. Remove the lower basket from the
machine.
3. Replace the cleaned filter.
4. Fasten the water inlet hose to the
water tap again.
2. Pull off the lower spray arm in an
upward direction (A).
3. Loosen the fastening screw of the
upper spray arm and pull off the
spray arm (B).
4. Clean the spray arms under
running water.
5. Replace the spray arms.
Warning
Ensure that the fastening screws are
screwed tight.
�
�
�
�
29
GB
7
Troubleshooting:
What to do if the dishwasher will not run
•
•
•
•
•
•
Check that the mains plug is properly connected.
Are all fuses working?
Is the water supply fully turned on?
Is the dishwasher door closed firmly?
Have you pressed the On/Off button?
Is the filter on the water intake and dishwasher clogged?
The cleaning results are unsatisfactory
Uncleaned Dishes
Disorderly placement
-
Load your dishes as described in the manual.
Program selection
-
For products with program selecting feature, choose a longer program that
washes in higher temperatures.
Blocked impellers
-
Prior to starting the program, ensure by turning by hand that the upper and
lower impellers are freely rotating.
Clogged filters
From time to time, remove the complete filter system as shown in the manual
and wash it under flowing water.
Misplaced or displaced filters
After washing the filter system, replace them as shown in the manual.
Clogged impeller holes
Take out and clean the impellers from time to time as shown in the figure.
Overloading the baskets
Do not overload the baskets in excess of their capacity
Detergent kept under unsuitable conditions
-
-
-
-
-
If you are using powder detergents, do not store them in humid places after
you open their boxes. Keep them in a closed container, if possible. For ease-
of-storing, we recommend you to use tablet detergents.
Inadequate detergent
-
If you are using powder detergents, adjust the amount of detergent
according to the soiling degree of your dishes and/or program definitions. We
recommend you to use tablet detergents for optimum results.
30
GB
Inadequate rinse aid
Increase rinse aid setting or add rinse aid into rinse aid compartment.
Unsealed detergent dispenser lid
-
-
Always ensure that the detergent compartment lid is closed tightly after every
detergent filling process.
Drying
Disorderly placement
-
Load your dishes as described in the manual.
Inadequate rinse aid
Increase rinse aid setting or add rinse aid into rinse aid compartment.
Unloading the machine right after dishwashing
-
-
Do not unload your dishwasher right after washing process is completed.
Slightly open the door and wait for evacuation of the inside steam for a while.
Unload the dishes after the pieces cool down to a touchable level. Start
unloading process from the lower basket.
Program Selection
-
For products with program selecting feature, choose a longer program that
washes in higher temperatures.
Tea, Coffee And Lipstick Stains
Program Selection
-
For products with program selecting feature, choose a longer program that
washes in higher temperatures.
Detergent kept under unsuitable conditions
-
If you are using powder detergents, do not store them in humid places after
you open their boxes. Keep them in a closed container, if possible.
For ease-of-storing, we recommend you to use tablet detergents.
-
Usage of silverwaretkitchenware with corrupted surface quality
-
Silverware or kitchenware with corrupted surface quality should not be
washed in dishwashers.
31
GB
Lime Stains, Hazy Look
Inadequate rinse aid
Increase rinse aid setting or add rinse aid into rinse aid compartment.
Insufficient water softening
-
-
In products equipped with water softening setting, water softening should be
properly set in accordance with the hardness of the supply water. Add salt
into the salt container, if necessary.
Salt leakage*
Use the supplied salt funnel while filling in softening salt. Make sure that
-
the salt box cover is tightly closed after finishing the filling process. Run a
washing program to clean up the salts spilled in the machine. Recheck the
salt box cover after the program is completed.
Metallic Look In Bluish Rainbow Color
Excessive rinse aid
-
Lower rinse aid setting.
Hazy, MilkytDish Look And Bluish / Rainbow
Color Appearance In Glassware When They
Are Hold Against Light
Glass corrosion due to soft water
-
In products equipped with water softening setting, water softening should
be properly set in accordance with the hardness of the supply water. If your
supply water is soft (<5dH), do not use salt. For products with program
selecting feature, choose programs that wash in higher temperatures (e.g.
60-65°C).
32
GB
Scratch / Break In Glassware
Kitchenware containing Aluminum
Kitchenware that contains aluminum should not be washed in dishwashers.
Salt leakage*
Use the supplied salt funnel while filling in softening salt. Make sure that
-
-
the salt box cover is tightly closed after finishing the filling process. Run a
washing program to clean up the salts spilled in the machine. Recheck the
salt box cover after the program is completed.
Low water softening setting, inadequate salt*
-
In products equipped with water softening setting, water softening should be
properly set in accordance with the hardness of the supply water. Add salt
into the salt container, if necessary.
Detergent kept under unsuitable conditions
-
If you are using powder detergents, do not store them in humid places after
you open their boxes. Keep them in a closed container, if possible. For ease-
of-storing, we recommend you to use tablet detergents.
Overloading the baskets
-
In order to avoid scratches and breaks in glasses and other glass tableware
because of collision with each other during washing process arising from their
placement, do not overload the baskets in excess of their capacity.
Rusts, Blackening And Corruption Of Surface
Unsealed closing of the salt box cover*
-
Salt may cause oxidation on metal surfaces. Use the supplied salt funnel
while filling in softening salt. Make sure that the salt box cover is tightly
closed after finishing the filling process. Run a washing program to clean up
the salts spilled in the machine. Recheck the salt box cover after the program
is completed.
Grounding line
Check if your dishwasher is connected to the actual grounding line.
-
Otherwise, the static electric created in the dishwasher may remove the
protective coating on metal surfaces and cause blackening and corruption.
33
GB
Detergent Remains In The Detergent
Dispenser
Damp detergent compartment
-
Make sure that the detergent dispenser is well dried prior to filling it with
detergent.
Putting detergent in the detergent dispenser long before washing
Take care that detergent is put shortly before startup of washing.
Preventing opening of detergent dispenser lid during washing
-
-
Ensure that the lid of detergent dispenser is not opened during loading the
dishes so that entering of water from the impellers into it is prevented.
Detergent kept under unsuitable conditions
-
If you are using powder detergents, do not store them in humid places after
you open their boxes. Keep them in a closed container, if possible. For ease-
of-storing, we recommend you to use tablet detergents.
Clogged impeller holes
-
Take out and clean the impellers from time to time as shown in the figure.
Water Remained In The Dishwashing
Compartment After Washing
Clogged filters
From time to time, remove the complete filter system as shown in the manual
and wash it under flowing water.
Blocking / twisting of drainage hose
Connect the drainage hose as described in the manual.
-
-
Odour
Odor of new dishwasher
-
A new dishwasher has a peculiar odor. It will fade out after a couple of
washing.
Clogged filters
From time to time, remove the complete filter system as shown in the manual
and wash it under flowing water.
-
34
GB
Leaving the dishes in the dishwasher for a long time
-
If you are not going to run your dishwasher immediately, load the dishes into
your machine after scraping the excessive soil on them and do not tightly
close the door of the machine. Every other day, perform washing without
detergent in the shortest program for products with program selecting feature.
Foam
Loading the dishes into the dishwasher without completely drying after
washing them with handtwash detergent.
-
Hand-wash detergents do not contain antifoam. There is no need to hand-
wash the dishes with detergent before loading the dishes into the machine.
Scraping the coarse soil on the surfaces with a tissue paper or fork will be
sufficient.
Spilling rinse aid in the machine while filling
-
Take care that rinse aid is not spilled in the machine when you are filling it.
Clean any spilled amount with the help of a tissue paper/towel.
Leaving the rinse aid lid open or not closing it
-
Rinse aid compartment should always be closed as shown in the manual
after it is filled with rinse aid.
Erasing Of Decorations
Usage of decorated glasses and porcelains
-
Decorated glasses and decorated luster porcelains are not suitable for
dishwasher washing. Manufacturers of glassware and porcelain tableware
items do not recommend washing these items in the dishwashers either.
*: In products with a salt container
35
GB
Service
If your appliance ever malfunctions, check the notes and advice given in the
operating manual.
If this does not fix the problem, our customer service staff are available to assist
you.
36
GB
GB
17 1577 0100-03
|