Asus MW221 User Manual

MW221/MW201 Series  
LCD Monitor  
User Guide  
Table of contents  
Notices................................................................................................ iv  
Safety information ...............................................................................v  
Care & Cleaning................................................................................... vi  
Chapter 1:  
Product introduction  
1.1  
1.2  
1.3  
Welcome!.............................................................................. 1-1  
Package contents ................................................................. 1-1  
Monitor introduction............................................................. 1-2  
1.3.1  
1.3.2  
Front of the LCD monitor ....................................... 1-2  
Rear of the LCD monitor......................................... 1-3  
Chapter 2:  
Setup  
2.1  
2.2  
2.3  
2.4  
Connecting the cables.......................................................... 2-1  
Turning the monitor on ........................................................ 2-1  
Adjusting the monitor .......................................................... 2-2  
Detaching the arm/stand (for VESA wall mount) ................ 2-3  
Chapter 3:  
General Instruction  
3.1  
OSD (On-Screen Display) menu ............................................ 3-1  
3.1.1  
3.1.2  
How to reconfigure................................................. 3-1  
OSD Function Introduction ..................................... 3-1  
3.2  
3.3  
Troubleshooting (FAQ)......................................................... 3-4  
Supported operating modes................................................. 3-5  
iii  
Notices  
Federal Communications Commission Statement  
This device complies with Part 15 of the FCC Rules. Operation is subject to  
the following two conditions:  
• This device may not cause harmful interference, and  
• This device must accept any interference received including interference  
that may cause undesired operation.  
This equipment has been tested and found to comply with the limits for a  
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against harmful interference in a  
residential installation. This equipment generates, uses and can radiate radio  
frequency energy and, if not installed and used in accordance with  
manufacturer’s instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that interference will not  
occur in a particular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged to try to correct  
the interference by one or more of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and receiver.  
• Connect the equipment to an outlet on a circuit different from that to  
which the receiver is connected.  
• Consult the dealer or an experienced radio/TV technician for help.  
As an Energy Star® Partner, our company has determined that  
this product meets the Energy Star® guidelines for energy  
efficiency.  
Canadian Department of Communications Statement  
This digital apparatus does not exceed the Class B limits for radio noise  
emissions from digital apparatus set out in the Radio Interference  
Regulations of the Canadian Department of Communications.  
This class B digital apparatus complies with Canadian  
ICES-003.  
i v  
Safety information  
• Before setting up the monitor, carefully read all the documentation that  
came with the package.  
• To prevent fire or shock hazard, never expose the monitor to rain or  
moisture.  
• Never try to open the monitor cabinet. The dangerous high voltages  
inside the monitor may result in serious physical injury.  
• If the power supply is broken, do not try to fix it by yourself. Contact a  
qualified service technician or your retailer.  
• Before using the product, make sure all cables are correctly connected  
and the power cables are not damaged. If you detect any damage,  
contact your dealer immediately.  
• Slots and openings on the back or top of the cabinet are provided for  
ventilation. Do not block these slots. Never place this product near or  
over a radiator or heat source unless proper ventilation is provided.  
• The monitor should be operated only from the type of power source  
indicated on the label. If you are not sure of the type of power supply to  
your home, consult your dealer or local power company.  
• Use the appropriate power plug which complies with your local power  
standard.  
• Do not overload power strips and extention cords. Overloading can result  
in fire or electric shock.  
• Avoid dust, humidity, and temperature extremes. Do not place the  
monitor in any area where it may become wet. Place the monitor on a  
stable surface.  
• Unplug the unit during a lightning storm or if it will not be used for a long  
period of time. This will protect the monitor from damage due to power  
surges.  
• Never push objects or spill liquid of any kind into the slots on the monitor  
cabinet.  
• To ensure satisfactory operation, use the monitor only with UL listed  
computers which have appropriate configured receptacles marked  
between 100-240V AC.  
• If you encounter technical problems with the monitor, contact a qualified  
service technician or your retailer.  
v
Care & Cleaning  
• Before you lift or reposition your monitor, it is better to disconnect the  
cables and power cord. Follow the correct lifting techniques when  
positioning the monitor. When lifting or carrying the monitor, grasp the  
edges of the monitor. Do not lift the display by the stand or the cord.  
• Cleaning. Turn your monitor off and unplug the power cord. Clean the  
monitor surface with a lint-free, non-abrasive cloth. Stubborn stains may  
be removed with a cloth dampened with mild cleaner.  
• Avoid using a cleaner containing alcohol or acetone. Use a cleaner  
intended for use with the LCD. Never spray cleaner directly on the  
screen, as it may drip inside the monitor and cause an electric shock.  
The following symptoms are normal with the monitor:  
• The screen may flicker during the initial use due to the nature of the  
fluorescent light. Turn off the Power Switch and turn it on again to make  
sure that the flicker disappears.  
• You may find slightly uneven brightness on the screen depending on the  
desktop pattern you use.  
• When the same image is displayed for hours, an afterimage of the  
previous screen may remain after switching the image. The screen will  
recover slowly or you can turn off the Power Switch for hours.  
• When the screen becomes black or flashes, or cannot work anymore,  
contact your dealer or service center to fix it. Do not repair the screen  
by yourself!  
Conventions used in this guide  
WARNING: Information to prevent injury to yourself when trying to  
complete a task.  
CAUTION: Information to prevent damage to the components  
when trying to complete a task.  
IMPORTANT: Information that you MUST follow to complete a  
task.  
NOTE: Tips and additional information to aid in completing a task.  
v i  
Where to find more information  
Refer to the following sources for additional information and for product  
and software updates.  
1 . ASUS websites  
The ASUS websites worldwide provide updated information on ASUS  
2 . Optional documentation  
Your product package may include optional documentation, such as  
warranty card, that may have been added by your dealer. These  
documents are not part of the standard package.  
vii  
viii  
1.1 Welcome!  
Thank you for purchasing the ASUS® MW221/MW201 Series LCD monitor!  
The latest widescreen LCD monitor from ASUS provides a crisper, broader,  
and brighter display, plus a host of features that enhance your viewing  
experience. The ASUS® MW221/MW201 Series LCD monitor gives you a full  
view of documents and web pages, and saving you the trouble of having to  
scroll the bar while you read or surf the Internet.  
With these features, you can enjoy the convenience and delightful visual  
experience that the MW221/MW201 Series brings you!  
1.2 Package contents  
Check your MW221/MW201 Series LCD package for the following items:  
LCD monitor  
User manual CD  
Quick start guide  
1 x Power cord  
1 x VGA cable  
1 x DVI cable (For some models)  
1 x Audio cable  
1 x Rear cover  
1 x VESA cover  
If any of the above items is damaged or missing, contact your retailer  
immediately.  
ASUS LCD Monitor MW221/MW201 Series  
1-1  
1.3 Monitor introduction  
1.3.1 Front of the LCD monitor  
Stereo  
speaker  
Base  
1
2
3
4
5
6
1. Headphone port  
. This port connects a headphone with a stereo  
The headphone port is under the icon .  
mini-plug (3.5mm).  
The headphone is purchased separately.  
2. SPLENDID Button:  
• Use this hotkey to switch from five video preset modes (Game  
Mode, Night View Mode, Scenery Mode, Standard Mode, Theater  
Mode) with SPLENDID™ Video Enhancement Technology.  
• Exit the OSD menu or go back to the previous menu as the OSD  
menu is active.  
• Automatically adjust the image to its optimized position, clock,  
and phase by pressing this button for 2-4 seconds.  
3.  
Button:  
• Press this button to decrease the value of the function selected  
or move left/up to the previous function.  
• This is also a hotkey for Volume adjustment.  
1-2  
Chapter 1: Product introduction  
4. MENU Button:  
• Press this button to enter/select the icon (function) highlighted  
while the OSD is activated.  
5.  
6.  
Button:  
• Press this button to increase the value of the function selected  
or move right/down to the next fuction.  
• This is also a hotkey for Brightness adjustment.  
Power button/power indicator  
• Press this button to turn the monitor on/off  
• The color definition of the power indicator is as the below table.  
Status  
Description  
Blue  
ON  
Amber  
OFF  
Standby mode  
OFF  
1.3.2 Rear of the LCD monitor  
Rear connectors  
Rear connectors (from left to right)  
1. PWR port. This port connects the power connector from the  
bundled power cord.  
2. Audio-in port  
. This port connects PC audio source by the  
bundled audio cable.  
3. DVI port. This 24-pin port is for PC (Personal Computer) DVI-D  
digital signal connection.  
4. VGA port. This 15-pin port is for PC VGA connection.  
ASUS LCD Monitor MW221/MW201 Series  
1-3  
1-4  
Chapter 1: Product introduction  
2.1 Connecting the cables  
1. Remove the rear cover.  
2. Connect the cables as the following instructions:  
To connect the audio cable: connect one end of the audio cable to  
the monitor’s Audio-in port, and then connect the other end to the  
computer multi-media (or audio) card’s audio output.  
To connect the power cord: connect one end of the power cord  
securely to the monitor’s AC input port, the other end to a power outlet.  
To connect the VGA cable:  
a. Plug the VGA/DVI connector to the LCD monitor’s VGA/DVI port.  
b. Connect the other end of the VGA/DVI cable to your computer’s  
VGA/DVI port.  
c. Tighten the two screws to secure the VGA/DVI connector.  
3. Gather all the cables, then hold them with the cable holder.  
4. Close the rear connector. Align the cover to the four slots near the  
ports and the two slots at the bottom of the monitor, then close the  
cover carefully. A click indicates that the cover has been closed  
successfully.  
Cable holder  
2.2 Turning the monitor on  
Gently touch the power sensor  
power sensor. The power indicator  
monitor is ON.  
. See page 1-3 for the location of the  
lights up in blue to show that the  
ASUS LCD Monitor MW221/MW201 Series  
2-1  
2.3 Adjusting the monitor  
• For optimal viewing, we recommend that you look at the full face of the  
monitor, then adjust the monitor to the angle that is most comfortable  
for you.  
• Hold the stand to prevent the monitor from falling when you change its  
angle.  
• You can adjust the monitor’s angle from -5º to 25º.  
-5º~25º  
It is normal that the monitor slightly shakes while you adjust the the  
viewing angle.  
2-2  
Chapter 2: Setup  
2.4 Detaching the arm/stand  
(for VESA wall mount)  
The detachable stand of the MW221/MW201 Series LCD monitor is  
specially designed for VESA wall mount.  
To detach the arm/stand:  
1. Remove the rear cover.  
2. Push Button 1 on the arm/stand with one hand, then lift the monitor  
with the other hand at the same time.  
3. Have the front of the monitor face down on a table and use a  
screwdriver to remove the three screws on the arm/stand as the  
below drawing shows.  
4. Push Button 2 to remove the VESA cover.  
We recommend that you cover the table surface with soft cloth to  
prevent damage to the monitor.  
VESA  
cover  
Rear  
cover  
Button 1  
Screws  
Button 2  
The VESA wall mount kit (100 mm x 100 mm) is purchased separately.  
ASUS LCD Monitor MW221/MW201 Series  
2-3  
2-4  
Chapter 2: Setup  
3.1 OSD (On-Screen Display) menu  
3.1.1 How to reconfigure  
1. Press the MENU button to activate  
the OSD menu.  
2. Press  
and  
to navigate through the functions. Highlight and  
activate the desired function by pressing the MENU button. If the  
function selected has a sub-menu, press + and - again to navigate  
through the sub-menu functions. Highlight and activate the desired  
sub-menu function by pressing the MENU button.  
3. Press  
and  
to change the settings of the selected function.  
4. To exit the OSD menu, press the SPLENDID button. Repeat step 2 and  
step 3 to adjust any other function.  
3.1.2 OSD Function Introduction  
1. Spendid  
This function contains five  
sub-functions you can select  
for your preference.  
Scenery Mode: advance for scenery use with SPLENDID™ Video  
Enhancement.  
Standard Mode: advance for general Window use with  
SPLENDID™ Video Enhancement.  
Theater Mode: advance for movie use with SPLENDID™ Video  
Enhancement.  
Game Mode: advance for game use with SPLENDID™ Video  
Enhancement.  
Night View Mode: advance for dark-display use with SPLENDID™  
Video Enhancement.  
ASUS LCD Monitor MW221/MW201 Series  
3-1  
2. Image  
You can adjust brightness, contrast,  
sharpness, saturation,position (VGA  
only), and focus (VGA only) from  
this main function.  
Brightness: the adjusting range is from 0 to 100.  
hotkey to activate this function.  
is a  
Contrast: the adjusting range is from 0 to 100.  
Sharpness: the adjusting range is from 0 to 100.  
Saturation: the adjusting range is from 0 to 100.  
Position: adjusts the horizontal postition (H-Position) and the  
vertical position (V-Position) of the image. The adjusting range is  
from 0 to 100.  
Focus: reduces Horizonal-line noise and Vertical-line noise of the  
image by adjusting (Phase) and (Clock) separately. The adjusting  
range is from 0 to 100.  
Phase adjusts the phase of the pixel clock signal. With a wrong  
phase adjustment, the screen shows horizontal disturbances.  
Clock (pixel frequency) controls the number of pixels scanned by  
one horizontal sweep. If the frequency is not correct, the screen  
shows vertical stripes and the image is not proportional.  
3. Color  
Select the image color you like  
from this function.  
Color Temp.: contains five color modes including Cool, Normal,  
Warm, sRGB, and User mode.  
Skin Tone: contains three color modes including Reddish, Natural,  
and Yellowish.  
In the User mode, colors of R (Red), G (Green), and B (Bluee) are user-  
configurable; the adjusting range is from 0-100.  
3-2  
Chapter 3: General Instruction  
4. Input Select  
In this function, you can select  
either VGA or DVI input source.  
(Only for some models)  
5. System Setup  
Allow you to adjust the system.  
Volume: the adjusting range is from 0 to 100.  
activate this function.  
OSD Setup: adjusts the horizontal postition (H-Position) and  
the vertical position (V-Position) of the OSD. The adjusting range is  
from 0 to 100. In the OSD Timeout selection, you can adjust the  
OSD timeout from 10 to 120.  
is a hotkey to  
Language: there are eleven languages for your selection,  
including English, German, Italian, French, Dutch, Spanish, Russian,  
Traditional Chinese, Simplified Chinese, Japanese, and Korean.  
Information: shows the monitor information.  
Reset: Yes” allows you to revert to the preset mode.  
ASUS LCD Monitor MW221/MW201 Series  
3-3  
3.2 Troubleshooting (FAQ)  
Problem  
Power LED is not ON  
Possible Solution  
button to check if the monitor is in the ON  
• Press the  
mode.  
• Check if the power cord is properly connected to the  
monitor and the power outlet.  
The Power LED lights  
amber and there is  
no screen image  
• Check if the monitor and the computer are in the ON mode.  
• Make sure the signal cable is properly connected the  
monitor and the computer.  
• Inspect the signal cable and make sure none of the pins are  
bent.  
• Connect the computer with another available monitor to  
check if the computer is properly working.  
Screen image is too  
light or dark  
• Adjust the Contrast and Brightness settings via OSD.  
Screen image is not  
centered or sized  
properly  
• Press the SPLENDID button for two seconds to  
automatically adjust the image.  
• Adjust the H-Position or V-Position settings via OSD.  
Screen image  
• Make sure the signal cable is properly connected to the  
monitor and the computer.  
bounces or a wave  
pattern is present in  
the image  
• Move electrical devices that may cause electrical  
interference.  
Screen image has  
• Inspect the signal cable and make sure that none of the  
pins are bent.  
color defects (white  
does not look white)  
• Perform Reset via OSD.  
• Adjust the R/G/B color settings or select the Color  
Temperature via OSD.  
Screen image is  
blurry or fuzzy  
• Press the SPLENDID button for two seconds to  
automatically adjust the image.  
• Adjust the Phase and Clock settings via OSD.  
No sound or sound is  
low  
• Ensure that the audio cable is properly connected to the  
monitor and the computer  
• Adjust the volume settings of both your monitor and  
computer.  
• Ensure that the computer sound card driver is properly  
installed and activated.  
3-4  
Chapter 3: General Instruction  
3.3 Supported operating modes  
Standard  
Resolution  
Horizontal  
Frequency  
Vertical  
Pixel  
Frequency  
Frequency  
DOS  
VGA  
720 x 400  
640 x 480  
640 x 480  
640 x 480  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
1024 x 768  
1024 x 768  
1024 x 768  
1280 x 1024  
1280 x 1024  
1152 x 864  
1440 x 900  
1680 x 1050  
31.47KHz  
31.47KHz  
37.90KHz  
37.50KHz  
35.16KHz  
37.90KHz  
48.10KHz  
46.90KHz  
48.40KHz  
56.50KHz  
60.02KHz  
64.00KHz  
80.00KHz  
67.50KHz  
55.94KHz  
65.29KHz  
70Hz  
60Hz  
72Hz  
75Hz  
56Hz  
60Hz  
72Hz  
75Hz  
60Hz  
70Hz  
75Hz  
60Hz  
75Hz  
75Hz  
60Hz  
60Hz  
28.32MHz  
25.18MHz  
31.50MHz  
31.50MHz  
36.00MHz  
40.00MHz  
50.00MHz  
49.50MHz  
65.00MHz  
75.00MHz  
78.75MHz  
108.00MHz  
135.00MHz  
108.00MHz  
106.00MHz  
146.25MHz  
SVGA  
XGA  
SXGA  
VESA  
VESA  
VESA  
(Primary)  
* Modes not listed in the table may not be supported. For optimal  
resolution, we recommend that you choose a mode listed in the table  
above.  
ASUS LCD Monitor MW221/MW201 Series  
3-5  
3-6  
Chapter 3: General Instruction  

GE PP932 User Manual
GE JP386 User Manual
Frigidaire FFEC3024LB User Manual
Electrolux Thermaline 9CHG584121 User Manual
Dometic DOTRC11B User Manual
Cres Cor RO151FUA18B Q1 User Manual
Compaq AlphaPC 164LX User Manual
Axis Communications BLADE VIDEO SERVER AXIS 243Q User Manual
AT T E2662B User Manual
Atlantis A02 RA240 W54 User Manual