L1N64-SLI WS
Contents
Notices........................................................................................................ vii
Safety information .................................................................................... viii
About this guide ......................................................................................... ix
L1N64-SLI WS specifications summary ................................................... xi
Chapter 1:
Product introduction
1.1
1.2
Welcome! ...................................................................................... 1-1
Special features............................................................................ 1-2
1.2.1
1.2.2
Product highlights ........................................................... 1-2
ASUS Special features ................................................... 1-4
Chapter 2:
Hardware information
2.1
2.2
Before you proceed ..................................................................... 2-1
Motherboard overview................................................................. 2-2
2.2.1
2.2.2
2.2.3
2.2.4
Placement direction ........................................................ 2-2
Screw holes .................................................................... 2-2
Motherboard layout......................................................... 2-3
Layout contents............................................................... 2-4
2.3
2.4
Central Processing Unit (CPU) ................................................... 2-6
2.3.1
2.3.2
2.3.3
Installing the CPU ........................................................... 2-6
Installing the heatsink and fan ........................................ 2-9
Installing the fan............................................................ 2-12
System memory ......................................................................... 2-13
2.4.1
2.4.2
2.4.3
2.4.4
Overview....................................................................... 2-13
Memory configurations.................................................. 2-14
Installing a DIMM .......................................................... 2-15
Removing a DIMM ........................................................ 2-15
2.5
Expansion slots.......................................................................... 2-16
2.5.1
2.5.2
2.5.3
2.5.4
2.5.5
2.5.6
Installing an expansion card ......................................... 2-16
Configuring an expansion card ..................................... 2-16
Interrupt assignments ................................................... 2-17
PCI slot ......................................................................... 2-18
PCI Express x1 slot....................................................... 2-18
Four PCI Express x16 slots .......................................... 2-18
iii
Contents
2.6
2.7
Jumper ........................................................................................ 2-20
Connectors ................................................................................. 2-21
2.7.1
2.7.2
Rear panel connectors.................................................. 2-21
Internal connectors ....................................................... 2-23
Chapter 3:
Powering up
3.1
Starting up for the first time........................................................ 3-1
3.2
Powering off the computer.......................................................... 3-2
3.2.1
3.2.2
Using the OS shut down function.................................... 3-2
Using the dual function power switch.............................. 3-2
Chapter 4:
BIOS setup
4.1
Managing and updating your BIOS ............................................ 4-1
4.1.1
4.1.2
4.1.3
4.1.4
ASUS Update utility ........................................................ 4-1
Creating a bootable floppy disk....................................... 4-4
AFUDOS utility................................................................ 4-5
ASUS CrashFree BIOS 3 utility ...................................... 4-8
4.2
BIOS setup program .................................................................... 4-9
4.2.1
4.2.2
4.2.3
4.2.4
4.2.5
4.2.6
4.2.7
4.2.8
4.2.9
BIOS menu screen........................................................ 4-10
Menu bar....................................................................... 4-10
Navigation keys............................................................. 4-10
Menu items ....................................................................4-11
Sub-menu items.............................................................4-11
Configuration fields ........................................................4-11
Pop-up window ..............................................................4-11
Scroll bar........................................................................4-11
General help ..................................................................4-11
4.3
Main menu .................................................................................. 4-12
4.3.1
4.3.2
4.3.3
4.3.4
4.3.5
4.3.6
4.3.7
4.3.8
System Time ................................................................. 4-12
System Date ................................................................. 4-12
Legacy Diskette A ......................................................... 4-12
Language...................................................................... 4-12
Primary IDE Master/Slave............................................. 4-13
SATA 1-12 ..................................................................... 4-14
IDE Configuration.......................................................... 4-15
System Information....................................................... 4-16
iv
Contents
4.4
Advanced menu ......................................................................... 4-17
4.4.1
4.4.2
4.4.3
4.4.4
4.4.5
4.4.6
JumperFree Configuration ............................................ 4-17
CPU Configuration........................................................ 4-21
Chipset.......................................................................... 4-22
Onboard Devices Configuration.................................... 4-25
PCI PnP ........................................................................ 4-27
USB Configuration ........................................................ 4-28
4.5
Power menu................................................................................ 4-29
4.5.1
4.5.2
4.5.3
4.5.4
4.5.5
Suspend Mode [Auto] ................................................... 4-29
ACPI 2.0 Support.......................................................... 4-29
ACPI APIC Support....................................................... 4-29
APM Configuration........................................................ 4-30
Hardware Monitor ......................................................... 4-32
4.6
4.7
Boot menu .................................................................................. 4-34
4.6.1
4.6.2
4.6.3
Boot Device Priority ...................................................... 4-34
Boot Settings Configuration .......................................... 4-35
Security......................................................................... 4-36
Exit menu.................................................................................... 4-39
Chapter 5:
Software support
5.1
5.2
Installing an operating system ................................................... 5-1
Support CD information .............................................................. 5-1
5.2.1
5.2.2
5.2.3
5.2.4
5.2.5
5.2.6
5.2.7
Running the support CD ................................................. 5-1
Drivers menu................................................................... 5-2
Utilities menu .................................................................. 5-3
Make Disk menu ............................................................. 5-4
Manuals menu ................................................................ 5-5
ASUS Contact information.............................................. 5-5
Other information ............................................................ 5-6
v
Contents
Chapter 5:
Software support
5.1
5.2
Installing an operating system ................................................... 5-1
Support CD information .............................................................. 5-1
5.2.1
5.2.2
5.2.3
5.2.4
5.2.5
5.2.6
5.2.7
Running the support CD ................................................. 5-1
Drivers menu................................................................... 5-2
Utilities menu .................................................................. 5-3
Make Disk menu ............................................................. 5-5
Manuals menu ................................................................ 5-6
ASUS Contact information.............................................. 5-7
Other information ............................................................ 5-7
vi
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
•
•
This device may not cause harmful interference, and
This device must accept any interference received including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with manufacturer’s
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is
required to assure compliance with FCC regulations. Changes or modifications
to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of the
Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
vii
Safety information
Electrical safety
•
To prevent electrical shock hazard, disconnect the power cable from the
electrical outlet before relocating the system.
•
When adding or removing devices to or from the system, ensure that the
power cables for the devices are unplugged before the signal cables are
connected. If possible, disconnect all power cables from the existing system
before you add a device.
•
•
•
Before connecting or removing signal cables from the motherboard, ensure
that all power cables are unplugged.
Seek professional assistance before using an adpater or extension cord.
These devices could interrupt the grounding circuit.
Make sure that your power supply is set to the correct voltage in your area.
If you are not sure about the voltage of the electrical outlet you are using,
contact your local power company.
•
If the power supply is broken, do not try to fix it by yourself. Contact a
qualified service technician or your retailer.
Operation safety
•
Before installing the motherboard and adding devices on it, carefully read all
the manuals that came with the package.
•
Before using the product, make sure all cables are correctly connected and the
power cables are not damaged. If you detect any damage, contact your dealer
immediately.
•
•
To avoid short circuits, keep paper clips, screws, and staples away from
connectors, slots, sockets and circuitry.
Avoid dust, humidity, and temperature extremes. Do not place the product in
any area where it may become wet.
•
•
Place the product on a stable surface.
If you encounter technical problems with the product, contact a qualified
service technician or your retailer.
viii
About this guide
This user guide contains the information you need when installing and configuring
the motherboard.
How this guide is organized
This guide contains the following parts:
•
Chapter 1: Product introduction
This chapter describes the features of the motherboard and the new
technology it supports.
•
Chapter 2: Hardware information
This chapter lists the hardware setup procedures that you have to perform
when installing system components. It includes description of the switches,
jumpers, and connectors on the motherboard.
•
•
•
Chapter 3: Powering up
This chapter describes the power up sequence and ways of shutting down
the system.
Chapter 4: BIOS setup
This chapter tells how to change system settings through the BIOS Setup
menus. Detailed descriptions of the BIOS parameters are also provided.
Chapter 5: Software support
This chapter describes the contents of the support CD that comes with the
motherboard package.
Where to find more information
Refer to the following sources for additional information and for product and
software updates.
1.
2.
ASUS websites
The ASUS website provides updated information on ASUS hardware and
software products. Refer to the ASUS contact information.
Optional documentation
Your product package may include optional documentation, such as warranty
flyers, that may have been added by your dealer. These documents are not
part of the standard package.
ix
Conventions used in this guide
To make sure that you perform certain tasks properly, take note of the following
symbols used throughout this manual.
DANGER/WARNING: Information to prevent injury to yourself
when trying to complete a task.
CAUTION: Information to prevent damage to the components
when trying to complete a task.
IMPORTANT: Instructions that you MUST follow to complete a
task.
NOTE: Tips and additional information to help you complete a
task.
Typography
Bold text
Italics
Indicates a menu or an item to select.
Used to emphasize a word or a phrase.
<Key>
Keys enclosed in the less-than and greater-than sign
means that you must press the enclosed key.
Example: <Enter> means that you must press the
Enter or Return key.
<Key1+Key2+Key3>
If you must press two or more keys simultaneously, the
key names are linked with a plus sign (+).
Example: <Ctrl+Alt+D>
Command
Means that you must type the command exactly
as shown, then supply the required item or value
enclosed in brackets.
Example: At the DOS prompt, type the command line:
afudos /i[filename]
afudos /iL1N64WS.ROM
x
L1N64-SLI WS specifications summary
CPU
Supports 2 AMDAtholon™ 64FX Socket L1 (1207FX)
CPU
Supports AMD Cool ‘n’ Quiet™ Technology
AMD64 architecture enables simultaneous 32-bit and
64-bit computing
Chipset
2 x NVIDIA® MCP55PXE
2000 / 1600 MT/s
System bus
Memory
Dual-channel memory architecture
-
4 x 240-pin DIMM sockets support unbufferred
ECC/non-ECC DDR2 800/667/533/400 MHz
memory modules
-
Supports up to 8 GB system memory
Expansion slots
4 x PCI Express™ x16 slots (at x16, x8, x16, x8)
1 x PCI-E x1 slot
1 x PCI 2.2 slot
Scalable Link Interface
(SLI™)
Supports two identical NVIDIA® SLI™-ready graphics
cards
Storage
2x NVIDIA® MCP55PXE supports:
-
-
-
1 x IDE connector for up to two Ultra DMA
133/100 devices
12 x Serial ATA 3.0 Gb/s connectors support twelve
Serial ATA devices
RAID 0, RAID1, RAID 0+1, RAID 5, and JBOD
configurations spanning across Serial ATA drives
via the onboard NVIDIA® MediaShield™ RAID
controller
SiliconImage® Sil3531 Serial ATA controller supports:
1 x External Serial ATA 3.0 Gb/s on the rear panel
-
LAN
2 x Marvell® 88E1116 PHY support:
Gigabit LAN
Firewall function
Supports Teaming functions
Wake up from S5
High Definition Audio
SoundMAX® ADI AD1988B 8-channel High Definition
Audio CODEC
Supports Jack-Sensing, Enumeration, Multi-Streaming,
and Jack-Retasking Technology
Optical and Coaxial S/PDIF Out interfaces at the rear
panel
IEEE 1394
USB
VIA 6308P 1394 controller supports:
-
2 x IEEE 1394a connectors
Supports up to 10 USB 2.0/1.1 ports
(continued on the next page)
xi
L1N64-SLI WS specifications summary
ASUS special features
Performance
Intelligent overclocking tools:
-
-
ASUS C.P.R. (CPU Parameter Recall)
Adjustable FSB/DDR2 ratio. Fixed PCI/PCIe
frequencies.
-
Hyper Path 3
Precision Tweaker:
-
-
vDIMM: 25-step DRAM voltage control
vCore: Adjustable CPU voltage at 0.0125 V
increment
-
-
Stepless Frequency Selection(SFS) allows FSB
tuning from 200 MHz up to 400 MHz at 1 MHz
increment
PCI Express x16 frequency allows PCI Express x16
frequency tuning from 100 MHz to 150 MHz at 1
MHz increment
ASUS special features
Thermal
ASUS 8-Phase Power Design for each VRM
Q-Fan 2
ASUS Heat-pipe Thermal solution
ASUS special features
Life
Multi-language BIOS
SATA on the Go
CrashFree BIOS 3
Rear panel
1 x PS/2 keyboard port (purple)
1 x PS/2 mouse port (green)
1 x Parallel port
1 x External Serial ATA 3.0 Gb/s
1 x Optical S/PDIF Out port
1 x Coaxial S/PDIF Out port
2 x LAN (RJ-45) ports
4 x USB 2.0/1.1 ports
8-channel audio ports
Internal connectors
3 x USB 2.0 connectors support 6 additional USB 2.0
ports
1 x Floppy disk drive connector
1 x IDE connector
12 x Serial ATA connectors
2 x CPU / 4 x Chassis / 1 x Power / 3 x fan connectors
2 x IEEE 1394a connectors
1 x EZ-plug
Chassis intrusion connector
Front panel audio connector
1 x CD audio in connector
1 x TPM connector (optional)
24-pin ATX power connector
8-pin ATX 2.0/1.1 power connector
System panel connector
(continued on the next page)
xii
L1N64-SLI WS specifications summary
BIOS features
Manageability
8 Mb AMI BIOS, PnP, DMI 2.0, WfM2.0, SM BIOS 2.3
WOL by PME, WOR by PME, PXE, AI NET 2, Chassis
Intrusion
Power requirements
Support CD contents
ATX power supply (with 24-pin and 4-pin 12 V plugs)
ATX 12 V 2.0 compliant
Device drivers
BIOS flash utility under DOS
ASUS PC Probe II
ASUS Update
NVIDIA® RAID
Form factor
CEB form factor: 12 in x 10.5 in (30.5 cm x 26.7 cm)
*Specifications are subject to change without notice.
xiii
xiv
This chapter describes the motherboard
features and the new technologies
it supports.
Product
1
introduction
Chapter summary
1
1.1
1.2
Welcome! ...................................................................................... 1-1
Special features............................................................................ 1-2
ASUS L1N64-SLI WS
1.1
Welcome!
Thank you for buying an ASUS® L1N64-SLI WS motherboard!
The motherboard delivers a host of new features and latest technologies, making it
another standout in the long line of ASUS quality motherboards!
Before you start installing the motherboard, and hardware devices on it, check the
items in your package with the list below.
ASUS L1N64-SLI WS
1-1
1.2
Special features
1.2.1
Product highlights
Latest processor technology
The motherboard comes with dual 1207-pin surface mount Land Grid Array
(LGA) sockets coded Socket L1 (1207FX), designed for AMD processors. The
motherboard with the new socket delivers advanced performance and ensuring
reliable data protection. See page 2-6 for details.
AMD Cool ‘n’ Quiet Technology
The motherboard supports the AMD Cool ‘n’ Quiet Technology, which monitors
system operation and automatically adjusts CPU voltage and frequency for a cool
and quiet operating environment. See page 4-18 for details.
NVIDIA® Scalable Link Interface (SLI™)
The NVIDIA® Scalable Link Interface (SLI™) technology allows two graphics
processing units (GPUs) in a single system. This technology takes advantage of
the PCI Express™ bus architecture and features intelligent hardware and software
solutions that allows multiple GPUs to work together and achieve exceptional
graphics performance.
64-bit CPU support
The motherboard supports 64-bit computing, which is the next generation
technology to replace the current 32-bit architecture. The 64-bit architecture
delivers advanced system performance, faster memory access, and increased
productivity. This motherboard provides excellent compatibility and flexibility by
support either 64-bit or 32-bit architecture. See page 2-6 for details.
DDR2 memory support
The motherboard supports DDR2 memory that features data transfer rates of
800/667/533/400 MHz to meet the higher bandwidth requirements of the latest
3D graphics, multimedia, and Internet applications. The dual-channel DDR2
architecture doubles the bandwidth of your system memory to boost system
performance, eliminating bottlenecks with peak bandwidths of up to 10.7 GB/s.
See pages 2-13 to 2-14 for details.
1-2
Chapter 1: Product introduction
PCI Express™ interface
The motherboard fully supports PCI Express, the latest I/O interconnect technology
that speeds up the PCI bus. PCI Express features point-to-point serial
interconnections between devices and allows higher clockspeeds by carrying data
in packets. This high speed interface is software compatible with existing PCI
specifications. See page 2-18 for details.
Serial ATA I/II technology and SATA-On-The-Go
The motherboard fully supports the Serial ATA II 3.0 Gb/s technology through the
Serial ATA interfaces and the NVIDIA® nForce® 680a SLI™ chipset. The Serial
ATA 3 Gb/s specification provides twice the bandwidth of the current Serial
ATA products with a host of new features, including Power Management (PM)
Implementation Algorithm. Serial ATA allows for thinner, more flexible cables with
lower pin count and reduced voltage required. Leveraging these Serial ATA 3.0
Gb/s features is the SATA-On-The-Go. Supported by the Marvell® 88SE614x Serial
ATA controller, four Serial ATA 3.0 Gb/s connectors (three at mid-board and one
on the rear panel) provide smart setup, and hot-plug function. See pages 2-22 and
2-25 for details.
IEEE 1394a support
The IEEE 1394a interface provides high-speed and flexible PC connectivity to
a wide range of peripherals and devices compliant to the IEEE 1394a standard.
The IEEE 1394a interface allows up to 400 Mbps transfer rates through simple,
low-cost, high-bandwidth asynchronous (real-time) data interfacing between
computers, peripherals, and consumer electronic devices such as camcorders,
VCRs, printers, TVs, and digital cameras. See page 2-26 for details.
S/PDIF digital sound ready
The motherboard supports the S/PDIF technology through the S/PDIF interfaces
on the rear panel. The S/PDIF technology turns your computer into a high-end
entertainment system with digital connectivity to powerful audio and speaker
systems. See page 2-22 for details.
USB 2.0 technology
The motherboard implements the Universal Serial Bus (USB) 2.0 specification,
dramatically increasing the connection speed from the 12 Mbps bandwidth on USB
1.1 to a fast 480 Mbps on USB 2.0. USB 2.0 is backward compatible with USB 1.1.
See pages 2-22 and 2-26 for details.
ASUS L1N64-SLI WS
1-3
Dual Gigabit LAN solution
The motherboard comes with dual Gigabit LAN controllers to provide the total
solution for your networking needs. These network controllers use the PCI Express
segment to provide faster data bandwidth for your wired or wireless Internet, LAN,
and file sharing requirements. See page 2-21 for details.
1.2.2
ASUS Special features
Advanced Thermal Design
8-Phase Power Design
The ASUS 8-Phase Power Design prolongs CPU lifespan and keeps the
system stable by preventing high power stress to the CPU and power supply
module. The design ensures high efficiency operation to generate less heat
compared with conventional power solutions, thus achieving cool system
environment and making this motherboard ideal for overclocking.
ASUS CrashFree BIOS 3
The ASUS CrashFree BIOS 3 allows users to restore corrupted BIOS data from a
USB flash disk containing the BIOS file. This utility saves users the cost and hassle
of buying a replacement BIOS chip. See page 4-8 for details.
Precision Tweaker
This feature allows you to fine tune the CPU/memory voltage and gradually
increase the memory Front Side Bus (FSB) and PCI Express frequency at 1MHz
increment to achieve maximum system performance.
ASUS Multi-language BIOS
The multi-language BIOS allows you to select the language of your choice from the
available options. The localized BIOS menus allow easier and faster configuration.
See page 4-11 for details.
C.P.R. (CPU Parameter Recall)
The C.P.R. feature of the motherboard BIOS allows automatic re-setting to the
BIOS default settings in case the system hangs due to overclocking. When the
system hangs due to overclocking, C.P.R. eliminates the need to open the system
chassis and clear the RTC data. Simply shut down and reboot the system, and the
BIOS automatically restores the CPU default setting for each parameter.
1-4
Chapter 1: Product introduction
This chapter lists the hardware setup
procedures that you have to perform
when installing system components. It
includes description of the jumpers and
connectors on the motherboard.
Hardware
2
information
Chapter summary
2
2.1
2.2
2.3
2.4
2.5
2.6
2.7
Before you proceed ..................................................................... 2-1
Motherboard overview................................................................. 2-2
Central Processing Unit (CPU) ................................................... 2-6
System memory ......................................................................... 2-13
Expansion slots.......................................................................... 2-16
Jumper ........................................................................................ 2-20
Connectors ................................................................................. 2-21
ASUS L1N64-SLI WS
2.1
Before you proceed
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
•
•
Unplug the power cord from the wall socket before touching any
component.
Use a grounded wrist strap or touch a safely grounded object or to
a metal object, such as the power supply case, before handling
components to avoid damaging them due to static electricity.
•
•
Hold components by the edges to avoid touching the ICs on them.
Whenever you uninstall any component, place it on a grounded
antistatic pad or in the bag that came with the component.
•
Before you install or remove any component, ensure
that the ATX power supply is switched off or the power cord is detached
from the power supply. Failure to do so may cause severe damage to the
motherboard, peripherals, and/or components.
Onboard LED
The motherboard comes with a standby power LED. The green LED lights up
to indicate that the system is ON, in sleep mode, or in soft-off mode. This is a
reminder that you should shut down the system and unplug the power cable
before removing or plugging in any motherboard component. The illustration
below shows the location of the onboard LED.
SB_PWR
L1N64-SLI
WS
ON
Standby
Power
OFF
Powered
Off
L1N64-SLI WS Onboard LED
ASUS L1N64-SLI WS
2-ꢀ
2.2
Motherboard overview
Before you install the motherboard, study the configuration of your chassis to
ensure that the motherboard fits into it.
Make sure to unplug the power cord before installing or removing the
motherboard. Failure to do so can cause you physical injury and damage
motherboard components.
2.2.1
Placement direction
When installing the motherboard, make sure that you place it into the chassis in
the correct orientation. The edge with external ports goes to the rear part of the
chassis as indicated in the image below.
2.2.2
Screw holes
Place nine (9) screws into the holes indicated by circles to secure the motherboard
to the chassis.
Do not overtighten the screws! Doing so can damage the motherboard.
Place this side towards
the rear of the chassis
L1N64-SLI
WS
2-2
Chapter 2: Hardware information
2.2.3
Motherboard layout
26.7cm (10.5in)
PS/2KBMS
T: Mouse
B: Keyboard
ATX12V
HP_FAN2
HP_FAN1
CPU1_FAN
SPS_FAN
CPU0_FAN
SPDIF_O
SPDIF_O2
CPU0
CPU1
LAN2_USB34
LAN1_USB12
AUDIO
HP_FAN3
CHA_FAN1
CHA_FAN3
EZ_PLUG1
EATXPWR
Marvell
88E1116
PCIEX16_1
Super
I/O
®
NVIDIA
MCP55PXE
L1N64-SLI
WS
CR2032 3V
Lithium Cell
CMOS Power
PCIEX1_1
SATA 1/3/5
Marvell
88E1116
CD
8Mb
BIOS
PCIEX16_2
AAFP
SATA 2/4/6
SATA 7/9/11
®
NVIDIA
MCP55PXE
ADI
1988B
PCI1
SATA 8/10/12
PCIEX16_3
PCIEX16_4
VIA
VT6308P
COM1
SB_PWR
CHASSIS
CLRTC
PANEL
IE1394_1
IE1394_2
CHA_FAN2
FLOPPY
CHA_FAN4
USB910
USB78
USB56
TPM
ASUS L1N64-SLI WS
2-ꢁ
2.2.4
Layout contents
Slots
Page
2-13
2-18
2-18
2-18
1.
2.
3.
4.
DDR2 DIMM slots
PCI slots
PCI Express x16 slots
PCI Express x1 slot
Jumper
Page
1.
Clear RTC RAM (3-pin CLRTC)
2-20
Rear panel connectors
Page
2-21
2-21
2-21
2-21
2-21
2-21
2-21
2-21
2-22
2-22
2-22
2-22
2-22
2-22
2-22
2-22
1.
PS/2 mouse port (green)
2.
Parallel port
3.
LAN 1 (RJ-45) port
4.
LAN 2 (RJ-45) port
5.
Rear Speaker Out port (black)
Center/Subwoofer port (orange)
Line In port (light blue)
Line Out port (lime)
6.
7.
8.
9.
Microphone port (pink)
Side Speaker Out port (gray)
USB 2.0 ports 1 and 2
USB 2.0 ports 3 and 4
External SATA port
10.
11.
12.
13.
14.
15.
16.
Optical S/PDIF Out port
Coaxial S/PDIF Out port
PS/2 keyboard port (purple)
2-ꢂ
Chapter 2: Hardware information
Internal connectors
Page
2-23
2-23
2-25
1.
2.
3.
Floppy disk drive connector (34-1 pin FLOPPY)
NVIDIA® IDE connector (40-1 pin PRI_IDE)
NVIDIA® MCP55PXE Southbridge Serial ATA
connectors (7-pin SATA1-6 [red], SATA7-12 [black])
4.
5.
USB connectors (10-1 pin USB56, USB78, USB910)
2-26
2-26
IEEE 1394a port connectors (10-1 pin IE1394_1, 10-1 pin
IE1394_2)
6.
CPU, chassis, power, and Heat-pipe Fan connectors
(4-pin CPU0_FAN, 4-pin CPU1_FAN, 3-pin HP_FAN1~3, 3-pin
CHA_FAN1~4, 3-pin SPS_FAN1)
2-27
7.
8.
Chassis intrusion connector (4-1 pin CHASSIS)
2-28
2-28
Power connectors (24-pin EATXPWR, 8-pin ATX12V, 4-pin
EZ_PLUG1)
9.
Front panel audio connector (10-1 pin AAFP)
Internal audio connector (4-pin CD [black])
Serial port connector (10-1 pin COM1)
TPM connector (20-1 pin TPM)
2-29
2-30
2-30
2-31
2-32
10.
11.
12.
13.
System panel connector (20-8 pin PANEL)
•
•
•
•
•
System power LED (2-pin PLED)
Hard disk drive activity LED (2-pin IDE_LED)
System warning speaker (4-pin SPEAKER)
ATX power button/soft-off button (2-pin PWR)
Reset button (2-pin RESET)
ASUS L1N64-SLI WS
2-ꢃ
2.3
Central Processing Unit (CPU)
The motherboard comes with dual surface mount Socket L1 (1207FX) designed for
the AMD CPU in the Land Grid Array (LGA) package.
•
Upon purchase of the motherboard, make sure that the PnP cap is on
the socket and the socket contacts are not bent. Contact your retailer
immediately if the PnP cap is missing, or if you see any damage to the PnP
cap/socket contacts/motherboard components. ASUS shoulders the repair
cost only if the damage is shipment/transit-related.
•
•
Keep the cap after installing the motherboard. ASUS will process Return
Merchandise Authorization (RMA) requests only if the motherboard comes
with the cap on the Socket L1 (1207FX).
The product warranty does not cover damage to the socket contacts
resulting from incorrect CPU installation/removal, or misplacement/loss/
incorrect removal of the PnP cap.
2.3.1
Installing the CPU
To install a CPU:
1. Locate the CPU socket on the motherboard.
CPU1
CPU0
L1N64-SLI
WS
L1N64-SLI WS CPU Socket
•
•
Before installing the CPU, make sure that the cam box is facing towards
you and the load lever is on your left.
When installing only one CPU, always install the CPU on the CPU0
socket; otherwise, the system will not boot up.
2-ꢄ
Chapter 2: Hardware information
2.
Press the load lever with your thumb (A), then move it to the left (B) until it is
released from the retention tab.
Retention tab
Load lever
A
PnP cap
This side of
B
the socket box
should face
you.
To prevent damage to the socket pins, do not remove the PnP cap until you are
installing a CPU.
3.
4.
Lift the load lever in the direction of
the arrow to a 135º angle.
Lift the load plate with your thumb
and forefinger to a 100º angle (A),
B
then push the PnP cap from the
load plate window to remove (B).
A
Load plate
5.
Position the CPU
over the socket,
making sure that the
gold triangle is on the
bottom-right corner
of the socket. The
socket alignment
keys should fit into
the CPU notches.
Alignment keys
Gold triangle mark
ASUS L1N64-SLI WS
2-ꢅ
The CPU fits in only one correct orientation. DO NOT force the CPU into the
socket to prevent bending the connectors on the socket and damaging the CPU!
A
6.
Close the load plate (A), then push
the load lever (B) until it snaps into
the retention tab.
B
2-ꢆ
Chapter 2: Hardware information
2.3.2
Installing the heatsink and fan
The AMD processor requires a specially designed heatsink and fan assembly to
ensure optimum thermal condition and performance.
Make sure that you use only AMD-certified heatsink and fan assembly.
To install the CPU heatsink and fan:
1.
Place the heatsink on top of the installed CPU, making sure that the heatsink
fits properly on the retention module base.
•
•
•
The retention module base is already installed on the motherboard
upon purchase.
You do not have to remove the retention module base when
installing the CPU or installing other motherboard components.
If you purchased a separate CPU heatsink and fan assembly, make
sure that a Thermal Interface Material is properly applied to the CPU
heatsink or CPU before you install the heatsink and fan assembly.
CPU fan
CPU heatsink
Retention bracket lock
Retention bracket
Retention module base
Your boxed CPU heatsink and fan assembly should come with installation
instructions for the CPU, heatsink, and the retention mechanism. If the
instructions in this section do not match the CPU documentation, follow the
latter.
ASUS L1N64-SLI WS
2-ꢇ
2.
Attach one end of the retention bracket
to the retention module base.
3.
Align the other end of the retention
bracket (near the retention bracket
lock) to the retention module base.
A clicking sound denotes that the
retention bracket is in place.
Make sure that the fan and
heatsink assembly perfectly fits
the retention mechanism module
base, otherwise you cannot snap
the retention bracket in place.
4.
Push up the retention bracket lock on
the retention mechanism to secure the
heatsink and fan to the module base.
2-ꢀ0
Chapter 2: Hardware information
5.
When the fan and heatsink assembly is in place, connect the CPU fan cable
to the connector on the motherboard labeled CPU0_FAN.
CPU0_FAN
CPU0_FAN
CPU1_FAN
CPU1_FAN
L1N64-SLI
WS
L1N64-SLI WS CPU fan connectors
Do not forget to connect the CPU fan connector! Hardware monitoring errors
can occur if you fail to plug this connector.
6.
Repeat steps 1 to 5 to install the other heatsink if you have installed a second
CPU, then connect the fan cable to the 4-pin connector labeled CPU1_FAN.
ASUS L1N64-SLI WS
2-ꢀꢀ
2.3.3
Installing the fan
Install the fan only if you are using a passive cooler or a water cooler. Installing
the fan with an active CPU cooler will interfere with the airflow and destabilize
the system.
1.
Position the fan above the pipe
and heatsink assembly.
2.
Fit the grooved edge to the
heatsink.
3.
5.
Carefully push down the fan until
it snugly fits the heatsink, then
connect the fan cables.
4.
The above photo shows the fan
installed on the motherboard.
Repeat step 1-4 to install the other fans.
•
•
Plug the fan cables to any of the HP_FAN1~3 connectors on the
motherboard.
Make sure the fan is installed correctly to prevent damage to the fan and
motherboard components.
2-ꢀ2
Chapter 2: Hardware information
2.4
System memory
2.4.1
Overview
The motherboard comes with four Double Data Rate 2 (DDR2) Dual Inline Memory
Modules (DIMM) sockets.
A DDR2 module has the same physical dimensions as a DDR DIMM but has a
240-pin footprint compared to the 184-pin DDR DIMM. DDR2 DIMMs are notched
differently to prevent installation on a DDR DIMM socket.
The figure illustrates the location of the DDR2 DIMM sockets:
L1N64-SLI
WS
L1N64-SLI WS 240-pin DDR2 DIMM sockets
Channel
Sockets
Channel 1
Channel 2
DIMM_A1 and DIMM_B1
DIMM_A2 and DIMM_B2
•
When using only one CPU, install memory modules to DIMM_A1 and
DIMM_B1 slots only.
•
•
Always use memory modules with same memory size and frequency.
For dual-channel memory configuration, the DDR2 DIMMs can be installed
in DIMM_A1 and DIMM_A2 either in one CPU mode or dual CPU mode.
ASUS L1N64-SLI WS
2-ꢀꢁ
2.4.2
Memory configurations
You may install 256 MB, 512 MB, and 1 GB unbuffered ECC/non-ECC DDR2
DIMMs into the DIMM sockets.
•
For dual-channel configuration, the total size of memory module(s) installed
per channel must be the same (DIMM_A1 + DIMM_B1 = DIMM_A2 +
DIMM_B2).
•
Always install DIMMs with the same CAS latency. For optimum
compatibility, we recommend that you obtain memory modules from
the same vendor. Visit the ASUS website (www.asus.com) for the latest
Qualified Vendors List.
•
When using only one DDR2 DIMM module, install it into slot DIMM_A1
only.
•
For single-channel memory configuration, start installing the DDR2 DIMMs
from slot DIMM_A1 or DIMM_B1.
Important notice on installing Windows® XP 32-bit version
If you install Windows® XP 32-bit version Operating System (OS), the limitation
of this OS version is that it may reserve a certain amount of memory space for
system devices. We recommend that you install less than 3 GB system memory
if you would like to work under Windows® XP 32-bit version OS. The excess
memory installation will not cause any usage problem, but it will not give users
the benefit of manipulating this excess memory space.
Visit the ASUS FAQ site for further
explanation:
http://support.asus.com/faq/faq.
aspx?SLanguage=en-us
Under General Search, make the
selections as shown, then click Search.
Click the article titled “4GB memory installed but less memory size
detected.”
You also may check the URLs below for third party comments on this issue:
http://dlsvr01.asus.com/pub/ASUS/mb/4GB_Rev1.pdf
http://www.intel.com/support/motherboards/server/sb/cs-016594.htm
2-ꢀꢂ
Chapter 2: Hardware information
2.4.3
Installing a DIMM
Unplug the power supply before adding or removing DIMMs or other
system components. Failure to do so can cause severe damage to both the
motherboard and the components.
2
To install a DIMM:
DDR2 DIMM notch
3
1.
2.
3.
Unlock a DIMM socket by
pressing the retaining clips
outward.
Align a DIMM on the socket
such that the notch on the DIMM
matches the break on the socket.
1
Firmly insert the DIMM into the
socket until the retaining clips
snap back in place and the
DIMM is properly seated.
Unlocked retaining clip
•
A DDR2 DIMM is keyed with a notch so that it fits in only one direction. Do
not force a DIMM into a socket to avoid damaging the DIMM.
•
The DDR2 DIMM sockets do not support DDR DIMMs. DO not install DDR
DIMMs to the DDR2 DIMM sockets.
2.4.4
Removing a DIMM
To remove a DIMM:
2
1. Simultaneously press the retaining
clips outward to unlock the DIMM.
Support the DIMM lightly with
your fingers when pressing the
retaining clips. The DIMM might
get damaged when it flips out
with extra force.
1
DDR2 DIMM notch
1
2.
Remove the DIMM from the socket.
ASUS L1N64-SLI WS
2-ꢀꢃ
2.5
Expansion slots
In the future, you may need to install expansion cards. The following sub-sections
describe the slots and the expansion cards that they support.
Make sure to unplug the power cord before adding or removing expansion
cards. Failure to do so may cause you physical injury and damage motherboard
components.
2.5.1
Installing an expansion card
To install an expansion card:
1.
2.
3.
4.
Before installing the expansion card, read the documentation that came with
it and make the necessary hardware settings for the card.
Remove the system unit cover (if your motherboard is already installed in a
chassis).
Remove the bracket opposite the slot that you intend to use. Keep the screw
for later use.
Align the card connector with the slot and press firmly until the card is
completely seated on the slot.
5.
6.
Secure the card to the chassis with the screw you removed earlier.
Replace the system cover.
2.5.2
Configuring an expansion card
After installing the expansion card, configure the it by adjusting the software
settings.
1.
Turn on the system and change the necessary BIOS settings, if any. See
Chapter 4 for information on BIOS setup.
2.
3.
Assign an IRQ to the card. Refer to the tables on the next page.
Install the software drivers for the expansion card.
When using PCI cards on shared slots, ensure that the drivers support “Share
IRQ” or that the cards do not need IRQ assignments; otherwise, conflicts will
arise between the two PCI groups, making the system unstable and the card
inoperable.
2-ꢀꢄ
Chapter 2: Hardware information
2.5.3
Interrupt assignments
Standard interrupt assignments
IRQ
0
Standard function
System timer
1
4
Standard 101/102-key or Microsoft Natural Keyboard
Communications Port (COM1)*
5
6
NVIDIA nForce PCI system management
Standard floppy disk controller
8
System CMOS/real-time clock
9
9
9
Microsoft ACPI-compliant system
NVIDIA nForce networking controller
NVIDIA nForce networking controller #2
NVIDIA nForce PCI system management
PS/2 compatible mouse port
Numeric data processor
Silicon Image Sil 3531 SATA controller
NVIDIA GeForce 6600 GT
VIA OHCI compliant IEEE 1394 host controller
NVIDIA nForce 680a Serial ATA controller
Standard Enhanced PCI to USB host controller
Microsoft UAA Bus Driver for High Definition Audio
NVIDIA network bus enumerator
Standard OpenHCD USB host controller
NVIDIA nForce 680a Serial ATA controller
NVIDIA network bus enumerator
NVIDIA nForce 680a Serial ATA controller
NVIDIA nForce 680a Serial ATA controller
NVIDIA nForce 680a Serial ATA controller
NVIDIA nForce 680a Serial ATA controller
11
12
13
16
17
17
20
20
21
22
22
22
23
23
45
46
47
* These IRQs are usually available for ISA or PCI devices.
ASUS L1N64-SLI WS
2-ꢀꢅ
2.5.4
PCI slot
The PCI slot supports cards such as a LAN card, SCSI card, USB card, and other
cards that comply with PCI specifications. Refer to the figure below for the location
of the slot.
2.5.5
PCI Express x1 slot
This motherboard supports PCI Express x1 network cards, SCSI cards and other
cards that comply with the PCI Express specifications. Refer to the figure below for
the location of the slot.
2.5.6
Four PCI Express x16 slots
This motherboard supports four SLI-ready PCI Express x16 graphic cards that
comply with the PCI Express specifications. The cards run at x16, x8, x16, x8
mode. Refer to the figure below for the location of the slots.
PCI Express x16 slot (blue)
PCI Express x16 slot (black)
PCI Express x1 slot
PCI Express x16 slot (blue)
PCI Express x16 slot (black)
PCI slot
2-ꢀꢆ
Chapter 2: Hardware information
•
Connect a rear chassis fan to the chassis (CHA_FAN1 or CHA_FAN2)
connector when using two graphics cards for better thermal environment.
See page 2-27 for details.
•
In single card mode, you may use either the blue or black slot for PCI
Express x16 graphics cards.
•
We recommend that you provide sufficient power when running NVIDIA®
SLI™ mode. See page 2-25 for details.
ASUS L1N64-SLI WS
2-ꢀꢇ
2.6
Jumper
Clear RTC RAM (CLRTC)
This jumper allows you to clear the Real Time Clock (RTC) RAM in
CMOS. You can clear the CMOS memory of date, time, and system setup
parameters by erasing the CMOS RTC RAM data. The onboard button
cell battery powers the RAM data in CMOS, which include system setup
information such as system passwords.
To erase the RTC RAM:
1. Turn OFF the computer and unplug the power cord.
2. Remove the onboard battery.
3. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on
pins 2-3 for about 5~10 seconds, then move the cap back to pins 1-2.
4. Reinstall the battery.
5. Plug the power cord and turn ON the computer.
6. Hold down the <Del> key during the boot process and enter BIOS setup
to re-enter data.
Except when clearing the RTC RAM, never remove the cap on CLRTC jumper
default position. Removing the cap will cause system boot failure!
CLRTC
L1N64-SLI
WS
1
2
2
3
Normal
(Default)
Clear RTC
L1N64-SLI WS Clear RTC RAM
•
•
Make sure to re-enter your previous BIOS settings after you clear the
CMOS.
You do not need to clear the RTC when the system hangs due to
overclocking. For system failure due to overclocking, use the C.P.R. (CPU
Parameter Recall) feature. Shut down and reboot the system so the BIOS
can automatically reset parameter settings to default values.
2-20
Chapter 2: Hardware information
2.7
Connectors
2.7.1
Rear panel connectors
1
2
3
4
5 6 7 8
16
15
14
12
11
10 9
13
1.
2.
PS/2 mouse port (green). This port is for a PS/2 mouse.
Parallel port. This 25-pin port connects a parallel printer, a scanner, or other
devices.
3.
4.
LAN 1 (RJ-45) port. Supported by Marvell® 88E1116 Gigabit LAN controller,
this port allows Gigabit connection to a Local Area Network (LAN) through a
network hub. Refer to the table below for the LAN port LED indications.
LAN 2 (RJ-45) port. Supported by the Marvell® 88E1116 Gigabit LAN
controller, this port allows Gigabit connection to a Local Area Network
(LAN) through a network hub. Refer to the table below for the LAN port LED
indications.
LAN port LED indications
ACT/LINK SPEED
LED LED
Activity/Link Speed LED
Status
Description
No link
Status
OFF
Description
OFF
10 Mbps connection
100 Mbps connection
1 Gbps connection
ORANGE
BLINKING
Linked
ORANGE
GREEN
Data activity
LAN port
5.
6.
7.
8.
Rear Speaker Out port (black). This port connects the rear speakers in a
4-channel, 6-channel, or 8-channel audio configuration.
Center/Subwoofer port (orange). This port connects the center/subwoofer
speakers.
Line In port (light blue). This port connects the tape, CD, DVD player, or
other audio sources.
Line Out port (lime). This port connects a headphone or a speaker. In
4-channel, 6-channel, and 8-channel configuration, the function of this port
becomes Front Speaker Out.
ASUS L1N64-SLI WS
2-2ꢀ
9.
Microphone port (pink). This port connects a microphone.
10. Side Speaker Out port (gray). This port connects the side speakers in an
8-channel audio configuration.
Refer to the audio configuration table below for the function of the audio ports in
2, 4, 6, or 8-channel configuration.
Audio 2, 4, 6, or 8-channel configuration
Port
Headset
4-channel
6-channel
8-channel
2-channel
Light Blue
Lime
Line In
Line In
Line In
Front Speaker Out
Mic In
Line In
Line Out
Front Speaker Out
Front Speaker Out
Mic In
Pink
Mic In
Mic In
Gray
–
–
–
–
–
Side Speaker Out
Rear Speaker Out
Black
Rear Speaker Out
–
Rear Speaker Out
Orange
Center/Subwoofer Center/Subwoofer
11. USB 2.0 ports 1 and 2. These two 4-pin Universal Serial Bus (USB) ports
are available for connecting USB 2.0 devices.
12. USB 2.0 ports 3 and 4. These two 4-pin Universal Serial Bus (USB) ports
are available for connecting USB 2.0 devices.
13. External SATA port. This port connects to an external SATA box or a Serial
ATA port multiplier.
The external SATA port supports
external Serial ATA 3.0 Gb/s
devices. Longer cables support
higher power requirements to
deliver signal up to two meters
away, and enables improved hot-
swap function.
14. Optical S/PDIF Out port. This port connects an external audio output device
via an optical S/PDIF cable.
15. Coaxial S/PDIF Out port. This port connects an external audio output device
via an coaxial S/PDIF cable.
16. PS/2 keyboard port (purple). This port is for a PS/2 keyboard.
2-22
Chapter 2: Hardware information
2.7.2
Internal connectors
1.
Floppy disk drive connector (34-1 pin FLOPPY)
This connector is for the provided floppy disk drive (FDD) signal cable. Insert
one end of the cable to this connector, then connect the other end to the
signal connector at the back of the floppy disk drive.
Pin 5 on the connector is removed to prevent incorrect cable connection when
using a FDD cable with a covered Pin 5.
FLOPPY
L1N64-SLI
WS
PIN 1
NOTE: Orient the red markings on
the floppy ribbon cable to PIN 1.
L1N64-SLI WS Floppy disk drive connector
2.
NVIDIA® IDE connector (40-1 pin PRI_IDE)
The onboard IDE connector is for the Ultra DMA (133/)100/66 signal cable.
There are three connectors on each Ultra DMA 133/100/66 signal cable:
blue, black, and gray. Connect the blue connector to the motherboard’s IDE
connector, then select one of the following modes to configure your device.
PRI_IDE
NOTE: Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
L1N64-SLI
WS
L1N64-SLI WS IDE connector
ASUS L1N64-SLI WS
2-2ꢁ
Drive jumper setting
Mode of
Cable connector
device(s)
Single device
Two devices
Cable-Select or Master
Cable-Select
-
Black
Black
Master
Slave
Master
Slave
Gray
Master
Slave
Black or gray
•
•
Pin 20 on the IDE connector is removed to match the covered hole on the
Ultra DMA cable connector. This prevents incorrect insertion when you
connect the IDE cable.
Use the 80-conductor IDE cable for Ultra DMA 100/66 IDE devices.
If any device jumper is set as “Cable-Select,” make sure all other device
jumpers have the same setting.
2-2ꢂ
Chapter 2: Hardware information
3.
NVIDIA® MCP55PXE Southbridge Serial ATA connectors (7-pin SATA1-6
[red], SATA7-12 [black])
These connectors are for the Serial ATA signal cables for Serial ATA 3.0
Gb/s hard disk and optical disk drives. The Serial ATA 3.0 Gb/s is backward
compatible with Serial ATA 1.5 Gb/s specification.
If you installed Serial ATA hard disk drives, you can create a RAID 0, RAID
1, RAID 0+1, RAID 5, or JBOD configuration through the onboard NVIDIA®
MediaShield™ controller.
GND
RSATA_TXP3
RSATA_TXN3
GND
RSATA_RXP3
RSATA_RXN3
GND
GND
RSATA_TXP5
RSATA_TXN5
GND
RSATA_RXP5
RSATA_RXN5
GND
SATA 1/3/5
SATA 2/4/6
GND
RSATA_RXN1
RSATA_RXP1
GND
RSATA_TXN1
RSATA_TXP1
GND
GND
RSATA_TXP4
RSATA_TXN4
GND
GND
RSATA_TXP6
RSATA_TXN6
GND
GND
RSATA_RXN2
RSATA_RXP2
GND
RSATA_RXP4
RSATA_RXN4
GND
RSATA_RXP6
RSATA_RXN6
GND
RSATA_TXN2
RSATA_TXP2
GND
L1N64-SLI
WS
GND
RSATA_TXP9
RSATA_TXN9
GND
RSATA_RXP9
RSATA_RXN9
GND
GND
RSATA_TXP11
RSATA_TXN11
GND
RSATA_RXP11
RSATA_RXN11
GND
SATA 7/9/11
SATA 8/10/12
GND
RSATA_RXN7
RSATA_RXP7
GND
RSATA_TXN7
RSATA_TXP7
GND
GND
RSATA_TXP10
RSATA_TXN10
GND
RSATA_RXP10
RSATA_RXN10
GND
GND
RSATA_TXP12
RSATA_TXN12
GND
RSATA_RXP12
RSATA_RXN12
GND
GND
RSATA_RXN8
RSATA_RXP8
GND
RSATA_TXN8
RSATA_TXP8
GND
L1N64-SLI WS SATA connectors
ASUS L1N64-SLI WS
2-2ꢃ
4.
USB connectors (10-1 pin USB56, USB78, USB910)
These connectors are for USB 2.0 ports. Connect the USB/GAME module
cable to any of these connectors, then install the module to a slot opening at
the back of the system chassis. These USB connectors comply with USB 2.0
specification that supports up to 480 Mbps connection speed.
USB910 USB78 USB56
L1N64-SLI
WS
PIN1
PIN1
PIN1
L1N64-SLI WS USB 2.0 connectors
Never connect a 1394 cable to the USB connectors. Doing so will damage the
motherboard!
5.
IEEE 1394a port connectors (10-1 pin IE1394_1; 10-1 pin IE1394_2)
These connectors are for IEEE 1394a ports. Connect the IEEE 1394a
module cables to any of these connectors, then install the module to a slot
opening at the back of the system chassis.
L1N64-SLI
WS
IE1394_1
IE1394_2
1
1
L1N64-SLI WS IEEE 1394 connectors
Never connect a USB cable to the IEEE 1394a connector. Doing so will damage
the motherboard!
2-2ꢄ
Chapter 2: Hardware information
6.
CPU, Chassis, Power, and Heat-pipe Fan connectors
(4-pin CPU0_FAN, 4- pin CPU1-FAN, 3-pin HP_FAN1~3 3-pin CHA_
FAN1~4, SPS_FAN1)
The fan connectors support cooling fans of 350 mA ~ 2000 mA (24 W max.) or
a total of 1 A ~ 3.48 A (41.76 W max.) at +12V. Connect the fan cables to the
fan connectors on the motherboard, making sure that the black wire of each
cable matches the ground pin of the connector.
Do not forget to connect the fan cables to the fan connectors. Insufficient air
flow inside the system may damage the motherboard components. These are
not jumpers! Do not place jumper caps on the fan connectors!
CPU0_FAN
CPU1_FAN HP_FAN1 HP_FAN2 SPS_FAN CPU0_FAN
SPS_FAN
HP_FAN1
HP_FAN2
CPU1_FAN
HP_FAN3
GND
Rotation
HP_FAN3
CHA_FAN1
+12V
CHA_FAN3
L1N64-SLI
WS
CHA_FAN1 CHA_FAN3 CHA_FAN2 CHA_FAN4
CHA_FAN2
CHA_FAN4
L1N64-SLI WS Fan connectors
ASUS L1N64-SLI WS
2-2ꢅ
7.
Chassis intrusion connector (4-1 pin CHASSIS)
This connector is for a chassis-mounted intrusion detection sensor or switch.
Connect one end of the chassis intrusion sensor or switch cable to this
connector. The chassis intrusion sensor or switch sends a high-level signal to
this connector when a chassis component is removed or replaced. The signal
is then generated as a chassis intrusion event.
By default, the pins labeled “Chassis Signal” and “Ground” are shorted with
a jumper cap. Remove the jumper caps only when you intend to use the
chassis intrusion detection feature.
L1N64-SLI
WS
CHASSIS
(Default)
L1N64-SLI WS Chassis intrusion connector
8.
Power connectors (24-pin EATXPWR, 8-pin EATX12V, 4-pin EZ_PLUG1)
These connectors are for ATX power supply plugs. The power supply plugs
are designed to fit these connectors in only one orientation. Find the proper
orientation and push down firmly until the connectors completely fit.
for CPU1
for CPU0
EATXPWR
ATX12V
L1N64-SLI
WS
EZ_PLUG1
L1N64-SLI WS ATX power connectors
•
•
Make sure to connect the 8-pin ATX +12V power plug when installing two
CPUs.
You can either use the 4-pin +12V power plug or 8-pin ATX +12V power
plug when installing only one CPU.
2-2ꢆ
Chapter 2: Hardware information
•
For a fully configured system, we recommend that you use a power supply
unit (PSU) that complies with ATX 12 V Specification 2.0 (or later version)
and provides a minimum power of 600 W.
•
Do not forget to connect the 4-pin/8-pin ATX +12 V power plug; otherwise,
the system will not boot up.
•
Make sure to connect the EZ Plug™ when using two PCI Express graphics
card and a 20-pin ATX power supply unit; otherwise, the system will be
unstable.
•
Use of a PSU with a higher power output is recommended when
configuring a system with more power-consuming devices. The system
may become unstable or may not boot up if the power is inadequate.
9.
Front panel audio connector (10-1 pin AAFP)
This connector is for a chassis-mounted front panel audio I/O module that
supports either HD Audio or legacy AC`97 audio standard. Connect one end
of the front panel audio I/O module cable to this connector.
AAFP
HD Audio-compliant
pin definition
Legacy AC ‘97 audio
pin definition
L1N64-SLI
WS
L1N64-SLI WS Analog front panel connector
•
•
We recommend that you connect a high-definition front panel audio
module to this connector to avail of the motherboard’s high-definition audio
capability.
By default, this connector is set to [AC97]. If you want to connect a high-
definition front panel audio module to this connector, set the Front Panel
Type item in the BIOS to [HD Audio]. See page 4-23 for details.
ASUS L1N64-SLI WS
2-2ꢇ
10. Internal audio connector (4-pin CD [Black])
These connectors allow you to receive stereo audio input from sound sources
such as a CD-ROM, TV tuner, or MPEG card.
L1N64-SLI
WS
CD
(black)
L1N64-SLI WS Internal audio connector
11. Serial port connector (10-1 pin COM1)
This connector is for a serial (COM) port. Connect the serial port module
cable to this connector, then install the module to a slot opening at the back
of the system chassis.
L1N64-SLI
WS
COM1
PIN 1
L1N64-SLI WS COM port connector
2-ꢁ0
Chapter 2: Hardware information
12. TPM connector (20-1 pin TPM) [Optional]
This connector supports a Trusted Platform Module (TPM) system, which can
securely store keys, digital certificates, passwords, and data. A TPM system
also helps enhance network security, protects digital identities, and ensures
platform integrity.
L1N64-SLI
WS
TPM
PIN 1
L1N64-SLI WS TPM connector
The TPM module is purchased separately.
ASUS L1N64-SLI WS
2-ꢁꢀ
13. System panel connector (20-8 pin PANEL)
This connector supports several chassis-mounted functions.
PLED
SPEAKER
PANEL
L1N64-SLI
WS
IDE_LED
RESET
PWRSW
* Requires an ATX power supply.
L1N64-SLI WS System panel connector
•
•
System power LED (2-pin PLED)
This 3-pin connector is for the system power LED. Connect the chassis
power LED cable to this connector. The system power LED lights up when
you turn on the system power, and blinks when the system is in sleep mode.
Hard disk drive activity LED (2-pin IDE_LED)
This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity
LED cable to this connector. The IDE LED lights up or flashes when data is
read from or written to the HDD.
•
•
System warning speaker (4-pin SPEAKER)
This 4-pin connector is for the chassis-mounted system warning speaker. The
speaker allows you to hear system beeps and warnings.
ATX power button/soft-off button (2-pin PWRSW)
This connector is for the system power button. Pressing the power button
turns the system on or puts the system in sleep or soft-off mode depending
on the BIOS settings. Pressing the power switch for more than four seconds
while the system is ON turns the system OFF.
•
Reset button (2-pin RESET)
This 2-pin connector is for the chassis-mounted reset button for system
reboot without turning off the system power.
2-ꢁ2
Chapter 2: Hardware information
This chapter describes the power up
sequence and ways of shutting down the
system.
Powering up
3
Chapter summary
3
3.1
Starting up for the first time........................................................ 3-1
3.2
Powering off the computer.......................................................... 3-2
ASUS L1N64-SLI WS
3.1
Starting up for the first time
1.
2.
3.
After making all the connections, replace the system case cover.
Be sure that all switches are off.
Connect the power cord to the power connector at the back of the system
chassis.
4.
5.
Connect the power cord to a power outlet that is equipped with a surge
protector.
Turn on the devices in the following order:
a. Monitor
b. External SCSI devices (starting with the last device on the chain)
c. System power
6.
After applying power, the system power LED on the system front panel case
lights up. For systems with ATX power supplies, the system LED lights up
when you press the ATX power button. If your monitor complies with “green”
standards or if it has a “power standby” feature, the monitor LED may light up
or switch between orange and green after the system LED turns on.
The system then runs the power-on self tests or POST. While the tests are
running, the BIOS beeps or additional messages appear on the screen.
If you do not see anything within 30 seconds from the time you turned on
the power, the system may have failed a power-on test. Check the jumper
settings and connections or call your retailer for assistance.
7.
At power on, hold down the <Delete> key to enter the BIOS Setup. Follow the
instructions in Chapter 4.
ASUS L1N64-SLI WS
ꢁ-ꢀ
3.2
Powering off the computer
3.2.1
Using the OS shut down function
If you are using Windows® 2000:
1.
2.
Click the Start button then click Shut Down...
Make sure that the Shut Down option button is selected, then click the OK
button to shut down the computer.
3.
The power supply should turn off after Windows® shuts down.
If you are using Windows® XP:
1.
2.
3.
Click the Start button then select Turn Off Computer.
Click the Turn Off button to shut down the computer.
The power supply should turn off after Windows® shuts down.
3.2.2
Using the dual function power switch
While the system is ON, pressing the power switch for less than four seconds puts
the system to sleep mode or to soft-off mode, depending on the BIOS setting.
Pressing the power switch for more than four seconds lets the system enter the
soft-off mode regardless of the BIOS setting. Refer to section “4.5 Power Menu”
in Chapter 4 for details.
ꢁ-2
Chapter ꢁ: Powering up
This chapter tells how to change
the system settings through the BIOS
Setup menus. Detailed descriptions
of the BIOS parameters are also
provided.
BIOS setup
4
Chapter summary
4
4.1
4.2
4.3
4.4
4.5
4.6
4.7
Managing and updating your BIOS ............................................ 4-1
BIOS setup program .................................................................... 4-9
Main menu .................................................................................. 4-12
Advanced menu ......................................................................... 4-17
Power menu................................................................................ 4-29
Boot menu .................................................................................. 4-34
Exit menu.................................................................................... 4-39
ASUS L1N64-SLI WS
4.1
Managing and updating your BIOS
The following utilities allow you to manage and update the motherboard Basic
Input/Output System (BIOS) setup.
1.
ASUS Update (Updates the BIOS in Windows® environment.)
2.
ASUS AFUDOS (Updates the BIOS in DOS mode using a bootable floppy
disk.)
Refer to the corresponding sections for details on these utilities.
Save a copy of the original motherboard BIOS file to a bootable floppy disk in
case you need to restore the BIOS in the future. Copy the original motherboard
BIOS using the ASUS Update or AFUDOS utilities.
4.1.1
ASUS Update utility
The ASUS Update is a utility that allows you to manage, save, and update the
motherboard BIOS in Windows® environment. The ASUS Update utility allows you
to:
•
•
•
•
•
Save the current BIOS file
Download the latest BIOS file from the Internet
Update the BIOS from an updated BIOS file
Update the BIOS directly from the Internet, and
View the BIOS version information.
This utility is available in the support CD that comes with the motherboard
package.
ASUS Update requires an Internet connection either through a network or an
Internet Service Provider (ISP).
Installing ASUS Update
To install ASUS Update:
1.
2.
Place the support CD in the optical drive. The Drivers menu appears.
Click the Utilities tab, then click ASUS Update. See page 5-3 for the Utilities
screen menu.
3.
The ASUS Update utility is copied to your system.
Quit all Windows® applications before you update the BIOS using this utility.
ASUS L1N64-SLI WS
4-1
Updating the BIOS through the Internet
To update the BIOS through the Internet:
1.
Launch the ASUS Update utility from the Windows® desktop by clicking Start
> Programs > ASUS > ASUSUpdate > ASUSUpdate. The ASUS Update main
window appears.
2.
Select Update BIOS from the
Internet option from the drop-down
menu, then click Next.
3.
Select the ASUS FTP site nearest
you to avoid network traffic, or
click Auto Select. Click Next.
4-2
Chapter 4: BIOS setup
4.
5.
From the FTP site, select the BIOS
version that you wish to download.
Click Next.
Follow the screen instructions to
complete the update process.
The ASUS Update utility is
capable of updating itself
through the Internet. Always
update the utility to avail of all
its features.
Updating the BIOS through a BIOS file
To update the BIOS through a BIOS file:
1.
Launch the ASUS Update utility from the Windows® desktop by clicking Start
> Programs > ASUS > ASUSUpdate > ASUSUpdate. The ASUS Update main
window appears.
2.
Select Update BIOS from a file
option from the drop-down menu,
then click Next.
3.
Locate the BIOS file from the Open
window, then click Save.
4.
Follow the screen instructions to
complete the update process.
ASUS L1N64-SLI WS
4-3
4.1.2
Creating a bootable floppy disk
1.
Do either one of the following to create a bootable floppy disk.
DOS environment
a. Insert a 1.44MB floppy disk into the drive.
b. At the DOS prompt, type format A:/S then press <Enter>.
Windows® XP environment
a. Insert a 1.44 MB floppy disk to the floppy disk drive.
b. Click Start from the Windows® desktop, then select My Computer.
c. Select the 3 1/2 Floppy Drive icon.
d. Click File from the menu, then select Format. A Format 3 1/2 Floppy Disk
window appears.
e. Windows® XP users: Select Create an MS-DOS startup disk from the
format options field, then click Start.
Windows® 2000 environment
To create a set of boot disks for Windows® 2000:
a. Insert a formatted, high density 1.44 MB floppy disk into the drive.
b. Insert the Windows® 2000 CD to the optical drive.
c. Click Start, then select Run.
d. In the Open field, type D:\bootdisk\makeboot a:
assuming that D is your optical drive letter.
e. Press <Enter>, then follow screen instructions to continue.
2.
Copy the original or the latest motherboard BIOS file to the bootable floppy
disk.
4-4
Chapter 4: BIOS setup
4.1.3
AFUDOS utility
The AFUDOS utility allows you to update the BIOS file in DOS environment using
a bootable floppy disk with the updated BIOS file. This utility also allows you to
copy the current BIOS file that you can use as backup when the BIOS fails or gets
corrupted during the updating process.
Copying the current BIOS
To copy the current BIOS file using the AFUDOS utility:
•
Make sure that the floppy disk is not write-protected and has at least 1.2
MB free space to save the file.
•
The succeeding BIOS screens are for reference only. The actual BIOS
screen displays may not be same as shown.
1.
2.
Copy the AFUDOS utility (afudos.exe) from the motherboard support CD to
the bootable floppy disk you created earlier.
Boot the system in DOS mode, then at the prompt type:
afudos /o[filename]
where the [filename] is any user-assigned filename not more than eight
alphanumeric characters for the main filename and three alphanumeric
characters for the extension name.
A:\>afudos /oOLDBIOS1.rom
Main filename
Extension name
3.
Press <Enter>. The utility copies the current BIOS file to the floppy disk.
A:\>afudos /oOLDBIOS1.rom
AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB))
Copyright (C) 2002 American Megatrends, Inc. All rights reserved.
Reading flash ..... done
Write to file...... ok
A:\>
The utility returns to the DOS prompt after copying the current BIOS file.
ASUS L1N64-SLI WS
4-5
Updating the BIOS file
To update the BIOS file using the AFUDOS utility:
1.
Visit the ASUS website (www.asus.com) and download the latest BIOS file for
the motherboard. Save the BIOS file to a bootable floppy disk.
Write the BIOS filename on a piece of paper. You need to type the exact BIOS
filename at the DOS prompt.
2.
3.
Copy the AFUDOS utility (afudos.exe) from the motherboard support CD to
the bootable floppy disk you created earlier.
Boot the system in DOS mode, then at the prompt type:
afudos /i[filename]
where [filename] is the latest or the original BIOS file on the bootable floppy
disk.
A:\>afudos /L1N64WS.rom
4.
The utility verifies the file and starts updating the BIOS.
A:\>afudos /L1N64WS.rom
AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB))
Copyright (C) 2002 American Megatrends, Inc. All rights reserved.
WARNING!! Do not turn off power during flash BIOS
Reading file ....... done
Reading flash ...... done
Advance Check ......
Erasing flash ...... done
Writing flash ...... 0x0008CC00 (9%)
Do not shut down or reset the system while updating the BIOS to
prevent system boot failure!
4-6
Chapter 4: BIOS setup
5.
The utility returns to the DOS prompt after the BIOS update process is
completed. Reboot the system from the hard disk drive.
A:\>afudos /L1N64WS.rom
AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB))
Copyright (C) 2002 American Megatrends, Inc. All rights reserved.
WARNING!! Do not turn off power during flash BIOS
Reading file ....... done
Reading flash ...... done
Advance Check ......
Erasing flash ...... done
Writing flash ...... done
Verifying flash .... done
Please restart your computer
A:\>
ASUS L1N64-SLI WS
4-7
4.1.4
ASUS CrashFree BIOS 3 utility
The ASUS CrashFree BIOS 3 is an auto recovery tool that allows you to restore
the BIOS file when it fails or gets corrupted during the updating process. You can
update a corrupted BIOS file using the motherboard support CD or the floppy disk
that contains the updated BIOS file.
Prepare the motherboard support CD or the floppy disk containing the updated
motherboard BIOS before using this utility.
Recovering the BIOS from the support CD
To recover the BIOS from the support CD:
1.
2.
3.
Turn on the system.
Insert the motherboard support CD to the optical drive.
The utility displays the following message and automatically checks the CD
for the BIOS file.
Award BootBlock BIOS v1.0
Copyright (c) 2000, Award Software, Inc.
BIOS ROM checksum error
Detecting IDE ATAPI device...
When found, the utility reads the BIOS file and starts flashing the corrupted
BIOS file.
Award BootBlock BIOS v1.0
Copyright (c) 2000, Award Software, Inc.
BIOS ROM checksum error
Detecting IDE ATAPI device...
Found CDROM, try to Boot from it... Pass
4.
Restart the system after the utility completes the updating process.
Recovering the BIOS from the USB flash disk
To recover the BIOS from the USB flash disk:
1.
2.
3.
Insert the USB flash disk that contains BIOS file to the USB port.
Turn on the system.
The utility will automatically checks the devices for the BIOS file When found,
the utility reads the BIOS file and starts flashing the corrupted BIOS file.
4.
Restart the system after the utility completes the updating process.
•
Only the USB flash disk with FAT 32/16/12 format and single partition can
support ASUS CrashFree BIOS 3. The device size should be smaller than
8GB.
•
DO NOT shut down or reset the system while updating the BIOS! Doing so
can cause system boot failure!
4-8
Chapter 4: BIOS setup
4.2
BIOS setup program
This motherboard supports a programmable firmware chip that you can update
using the provided utility described in section “4.1 Managing and updating your
BIOS.”
Use the BIOS Setup program when you are installing a motherboard, reconfiguring
your system, or prompted to “Run Setup.” This section explains how to configure
your system using this utility.
Even if you are not prompted to use the Setup program, you can change the
configuration of your computer in the future. For example, you can enable the
security password feature or change the power management settings. This
requires you to reconfigure your system using the BIOS Setup program so that the
computer can recognize these changes and record them in the CMOS RAM or the
firmware hub.
The firmware hub on the motherboard stores the Setup utility. When you start up
the computer, the system provides you with the opportunity to run this program.
Press <Del> during the Power-On-Self-Test (POST) to enter the Setup utility;
otherwise, POST continues with its test routines.
If you wish to enter Setup after POST, restart the system by pressing
<Ctrl+Alt+Delete>, or by pressing the reset button on the system chassis. You can
also restart by turning the system off and then back on. Do this last option only if
the first two failed.
The Setup program is designed to make it as easy to use as possible. Being a
menu-driven program, it lets you scroll through the various sub-menus and make
your selections from the available options using the navigation keys.
•
The default BIOS settings for this motherboard apply for most conditions
to ensure optimum performance. If the system becomes unstable after
changing any BIOS settings, load the default settings to ensure system
compatibility and stability. Select the Load Default Settings item under the
Exit Menu. See section “4.7 Exit Menu.”
•
The BIOS setup screens shown in this section are for reference purposes
only, and may not exactly match what you see on your screen.
•
Visit the ASUS website (www.asus.com) to download the latest BIOS file for
this motherboard.
ASUS LꢀNꢄꢂ-SLI WS
ꢂ-ꢇ
4.2.1
Menu items
Main
BIOS menu screen
Menu bar
Configuration fields
General help
BIOS SETUP UTILITY
Boot Tools
Advanced
Power
Exit
System Time
System Date
Legacy Diskette A
Language
[10:55:25]
[Mon 07/05/2006]
[1.44M, 3.5 in]
[English]
Use [ENTER], [TAB] or
[SHIFT-TAB] to select
a field.
Primary IDE Master
Primary IDE Slave
SATA 1
[ST320410A]
Use [+] or [-] to
[ASUS CD-S520/A]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
configure the System
SATA 2
SATA 3
SATA 4
SATA 5
Select Screen
Select Item
SATA 6
SATA 7
+-
Tab
F1
Change Field
Select Field
General Help
Save and Exit
Exit
SATA 8
SATA 9
SATA 10
F10
ESC
SATA 11
SATA 12
v02.58 (C)Copyright 1985-2006, American Megatrends, Inc.
Sub-menu items
Navigation keys
4.2.2
Menu bar
The menu bar on top of the screen has the following main items:
Main
For changing the basic system configuration
Advanced
Power
For changing the advanced system settings
For changing the advanced power management (APM)
configuration
Boot
Tools
Exit
For changing the system boot configuration
For configuring options for special functions
For selecting the exit options and loading default
settings
To select an item on the menu bar, press the right or left arrow key on the keyboard
until the desired item is highlighted.
4.2.3
Navigation keys
At the bottom right corner of a menu screen are the navigation keys for that
particular menu. Use the navigation keys to select items in the menu and change
the settings.
Some of the navigation keys differ from one screen to another.
ꢂ-ꢀ0
Chapter ꢂ: BIOS setup
4.2.4
Menu items
BIOS SETUP UTILITY
Boot Tools
Main
Advanced
Power
Exit
The highlighted item on the menu
bar displays the specific items for that
menu. For example, selecting Main
shows the Main menu items.
System Time
System Date
Legacy Diskette
Language
[10:55:25]
[Mon 07/05/2006]
[1.44M, 3.5 in]
[English]
Use [ENTER], [TAB] or
[SHIFT-TAB] to select
field.
A
a
Primary IDE Master
Primary IDE Slave
[ST320410A]
Use [+] or [-] to
configure the System
[ASUS CD-S520/A]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
SATA
SATA
SATA
SATA
SATA
SATA
SATA
SATA
SATA
1
2
3
4
5
6
7
8
9
Select Screen
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
+-
Tab
F1
F10
ESC
The other items (Advanced, Power,
Boot, and Exit) on the menu bar have
their respective menu items.
SATA 10
SATA 11
SATA 12
v02.58 (C)Copyright 1985-2006, American Megatrends, Inc.
Main menu items
4.2.5
Sub-menu items
A solid triangle before each item on any menu screen means that the iteam has a
sub-menu. To display the sub-menu, select the item and press <Enter>.
4.2.6
Configuration fields
These fields show the values for the menu items. If an item is user- configurable,
you can change the value of the field opposite the item. You cannot select an item
that is not user-configurable.
A configurable field is enclosed in brackets, and is highlighted when selected. To
change the value of a field, select it then press <Enter> to display a list of options.
Refer to “4.2.7 Pop-up window.”
4.2.7
Pop-up window
Select a menu item then press <Enter> to display a pop-up window with the
configuration options for that item.
4.2.8
Scroll bar
Advanced Chipset settings
WARNING: Setting wrong values in the sections below
may cause system to malfunction.
A scroll bar appears on the right side of a
menu screen when there are items that do
not fit on the screen. Press the
Up/Down arrow keys or <Page Up> /<Page
Down> keys to display the other items on
the screen.
Configure DRAM Timing by SPD
Memory Acceleration Mode
DRAM Idle Timer
[Enabled]
[Auto]
[Auto]
DRAm Refresh Rate
Graphic Adapter Priority
Graphics Aperture Size
Spread Spectrum
[
64 MB]
[Enabled]
[Enabled]
[1.4]
Select Screen
Select Item
ICH Delayed Transaction
MPS Revision
+-
F1
Change Option
General Help
F10 Save and Exit
ESC Exit
Pop-up window
4.2.9
General help
Scroll bar
At the top right corner of the menu screen
is a brief description of the selected item.
ASUS LꢀNꢄꢂ-SLI WS
ꢂ-ꢀꢀ
4.3
Main menu
When you enter the BIOS Setup program, the Main menu screen appears, giving
you an overview of the basic system information.
Refer to section “4.2.1 BIOS menu screen” for information on the menu screen
items and how to navigate through them.
BIOS SETUP UTILITY
Main
Advanced
Power
Boot
Exit
System Time
System Date
Legacy Diskette A
Language
[10:55:25]
[Mon 07/05/2006]
[1.44M, 3.5 in]
[English]
Use [ENTER], [TAB] or
[SHIFT-TAB] to select
a field.
Primary IDE Master
Primary IDE Slave
SATA 1
[ST320410A]
Use [+] or [-] to
[ASUS CD-S520/A]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
configure the System
SATA 2
SATA 3
SATA 4
SATA 5
Select Screen
Select Item
SATA 6
SATA 7
+-
Tab
F1
Change Field
Select Field
General Help
Save and Exit
Exit
SATA 8
SATA 9
SATA 10
F10
ESC
SATA 11
SATA 12
v02.58 (C)Copyright 1985-2006, American Megatrends, Inc.
4.3.1
System Time [xx:xx:xx]
Allows you to set the system time.
4.3.2
System Date [Day xx/xx/xxxx]
Allows you to set the system date.
4.3.3
Legacy Diskette A [1.44M, 3.5 in.]
Sets the type of floppy drive installed. Configuration options: [Disabled] [360K, 5.25
in.] [1.2M , 5.25 in.] [720K , 3.5 in.] [1.44M, 3.5 in.] [2.88M, 3.5 in.]
4.3.4
Language [English]
Allows you to choose the BIOS language version from the options. Configuration
options: [English] [Français] [German] [Japanese] [Chinese (GB)] [Chinese BIG5]
ꢂ-ꢀ2
Chapter ꢂ: BIOS setup
4.3.5
Primary IDE Master/Slave
The BIOS automatically detects the connected IDE devices. There is a separate
sub-menu for each IDE device. Select a device item, then press <Enter> to display
the IDE device information.
Primary IDE Master
Device
: Not Detected
Type
[Auto]
[Auto]
LBA/Large Mode
Block(Multi-sector Transfer) M [Auto]
PIO Mode
DMA Mode
[Auto]
[Auto]
SMART Monitoring
32Bit Data Transfer
[Auto]
[Disabled]
The BIOS automatically detects the values opposite the dimmed items (Device,
Vendor, Size, LBA Mode, Block Mode, PIO Mode, Async DMA, Ultra DMA, and
SMART monitoring). These values are not user-configurable. These items show
N/A if no IDE device is installed in the system.
Type [Auto]
Selects the type of IDE drive. Setting to [Auto] allows automatic selection of the
appropriate IDE device type. Select [CDROM] if you are specifically configuring a
CD-ROM drive. Select [ARMD] (ATAPI Removable Media Device) if your device is
either a ZIP, LS-120, or MO drive.
Configuration options: [Not Installed] [Auto] [CDROM] [ARMD]
LBA/Large Mode [Auto]
Enables or disables the LBA mode. Setting to [Auto] enables the LBA mode if the
device supports this mode, and if the device was not previously formatted with LBA
mode disabled. Configuration options: [Disabled] [Auto]
Block (Multi-sector Transfer) M [Auto]
Enables or disables data multi-sector transfer mode. When set to [Auto], the
data transfer from and to the device occurs multiple sectors at a time if the
device supports multi-sector transfer feature. When set to [Disabled], the data
transfer from and to the device occurs one sector at a time. Configuration options:
[Disabled] [Auto]
ASUS LꢀNꢄꢂ-SLI WS
ꢂ-ꢀꢁ
PIO Mode [Auto]
Selects the PIO mode.
Configuration options: [Auto] [0] [1] [2] [3] [4]
DMA Mode [Auto]
Selects the DMA mode. Configuration options: [Auto] [SWDMA0] [SWDMA1]
[SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0] [UDMA1] [UDMA2]
[UDMA3] [UDMA4] [UDMA5]
SMART Monitoring [Auto]
Sets the Smart Monitoring, Analysis, and Reporting Technology. Configuration
options: [Auto] [Disabled] [Enabled]
32Bit Data Transfer [Enabled]
Enables or disables 32-bit data transfer.
Configuration options: [Disabled] [Enabled]
4.3.6
SATA 1-12
While entering Setup, the BIOS automatically detects the presence of Serial ATA
devices. There is a separate sub-menu for each SATA device. Select a device
item, then press <Enter> to display the SATA device information.
SATA 1
Disabled: Disables
LBA Mode.
Device
: Not Detected
Auto: Enables LBA
Mode if the device
supports it and
the device is not
already formatted
with LBA Mode
LBA/Large Mode
[Auto]
Block(Multi-sector Transfer) M [Auto]
PIO Mode
DMA Mode
SMART Monitoring
32Bit Data Transfer
[Auto]
[Auto]
[Auto]
disabled.
[Enabled]
LBA/Large Mode [Auto]
Enables or disables the LBA mode. Setting to [Auto] enables the LBA mode if the
device supports this mode, and if the device was not previously formatted with LBA
mode disabled. Configuration options: [Disabled] [Auto]
ꢂ-ꢀꢂ
Chapter ꢂ: BIOS setup
Block (Multi-sector Transfer) M [Auto]
Enables or disables data multi-sector transfer mode. When set to [Auto], the
data transfer from and to the device occurs multiple sectors at a time if the
device supports multi-sector transfer feature. When set to [Disabled], the data
transfer from and to the device occurs one sector at a time. Configuration options:
[Disabled] [Auto]
PIO Mode [Auto]
Selects the PIO mode.
Configuration options: [Auto] [0] [1] [2] [3] [4]
DMA Mode [Auto]
Selects the DMA mode. Configuration options: [Auto] [SWDMA0] [SWDMA1]
[SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0] [UDMA1] [UDMA2]
[UDMA3] [UDMA4] [UDMA5]
SMART Monitoring [Auto]
Sets the Smart Monitoring, Analysis, and Reporting Technology. Configuration
options: [Auto] [Disabled] [Enabled]
32Bit Data Transfer [Enabled]
Enables or disables 32-bit data transfer.
Configuration options: [Disabled] [Enabled]
4.3.7
IDE Configuration
The items in this menu allow you to set or change the configurations for the IDE
devices installed in the system. Select an item then press <Enter> if you want to
configure the item.
Options
Disabled
IDE Configuration
OnChip RAID1 Function
OnChip RAID2 Function
[Disabled]
[Disabled]
Enabled
OnChip RAID1 Function [Disabled]
Enables or disables the onchip RAID function.
Configuration options: [Enabled] [Disabled]
OnChip RAID2 Function [By RAID1]
Configuration options: [By RAID1]
ASUS LꢀNꢄꢂ-SLI WS
ꢂ-ꢀꢃ
4.3.8
System Information
This menu gives you an overview of the general system specifications. The BIOS
automatically detects the items in this menu.
AMIBIOS
Version
:
:
0114
10/14/06
Build Date
Processor
Type
:
:
:
AND Engineering Sample
Speed
2815MHz
Count
4
System Memory
Usable Size:
2048MB
AMI BIOS
Displays the auto-detected BIOS information.
Processor
Displays the auto-detected CPU specification.
System Memory
Displays the auto-detected system memory.
ꢂ-ꢀꢄ
Chapter ꢂ: BIOS setup
4.4
Advanced menu
The Advanced menu items allow you to change the settings for the CPU and other
system devices.
Take caution when changing the settings of the Advanced menu items. Incorrect
field values can cause the system to malfunction.
BIOS SETUP UTILITY
Main
Advanced
Power
Boot
Tools
Exit
JumperFree Configuration
CPU Configuration
Chipset
Onboard Devices Configuration
PCIPnP
USB Configuration
Select Screen
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
+-
Tab
F1
F10
ESC
v02.58 (C)Copyright 1985-2006, American Megatrends, Inc.
4.4.1
JumperFree Configuration
Configure System Frequency/Voltage
Select the target CPU
frequency, and the
relevant parameters
will be auto-adjusted.
Frequencies higher
than CPU manufacturer
recommends are not
guaranteed to be
AI Overclocking
[Auto]
CPU FID/VID Control
Runtime Legacy PSB
[Auto]
[Disabled]
[Disabled]
[1000 MHz]
[1000 MHz]
[1000 MHz]
Cool N’Quiet
HyperTransport (CPU & CPU)
HyperTransport (CPU & SB1)
HyperTransport (CPU & SB2)
stable. If the system
becomes unstable,
return to the default.
AI Overclocking [Auto]
Allows you to select the overclocking options to achieve the desired CPU internal
frequency. Select either one of the preset overclocking configiuration options.
Manual
Auto
Allows you to individually set overclocking parameters.
Loads the optimal settings for the system.
Standard
Loads the standard settings for the system.
Overclock Profile Loads overclocking profiles with optimal parameters for
stability when overclocking.
EPP Memory
ASUS LꢀNꢄꢂ-SLI WS
ꢂ-ꢀꢅ
The following items appear only when you set the AI Overclocking item to
[manual].
FSB Frequency [200]
Allows you to adjust the FSB frequency. The value of this item is auto-detected by the
BIOS. Use the <+> and <-> keys to adjust the FSB frequency. You can also type the
desired FSB frequency using the numeric keypad. The values range from 200 to 400.
PCIE Frequency [100]
Allows you to adjust the PCIE frequency. The value of this item is auto-detected by the
BIOS. Use the <+> and <-> keys to adjust the PCIE frequency. You can also type the
desired PCIE frequency using the numeric keypad. The values range from 100 to 200.
The following items appear only when you set the AI Overclocking item to
[manual] or [EPP Memory].
CPU1/CPU2 VCORE Over-Voltage [Auto]
Allows you to enable or disable VCORE over-voltage.
Configuration options: [Auto] [+50mV] [+100mV] [+150mV] [+200mV]
DDR VTT Switch [Auto]
Configuration options: [Auto] [0.6 x DDR Voltage] [0.5 x DDR Voltage]
DDR Voltage [Auto]
Allows you to set the DDR memory voltage.
Configuration options: [Auto] [1.800V] [1.825V] [1.850V]...[2.475V] [2.500V]
Setting a very high voltage may damage the component permanently. Setting a
very low voltage may cause the system to become unstable.
HyperTransport Voltage [Auto]
Allows you to set the Hypertransport voltage.
Configuration options: [Auto] [1.200V] [1.250V] [1.300V] [1.350V] [1.400V]
1.5V Voltage [Auto]
Configuration options: [Auto] [1.500V] [1.525V] [1.550V]...[1.675V] [1.700V]
1.5V Stand-By Voltage [Auto]
Configuration options: [Auto] [1.500V] [1.600V] [1.700V]
AI Clock Skew 1 for Channel A/Channel B [Auto]
Configuration options: [Auto] [Normal] [Advance 150ps] [Advance 300ps]
...[Advance 900] [Delay 150ps] [Delay 300ps]...[Delay 900]
AI Clock Skew 2 for Channel A/Channel B [Auto]
Configuration options: [Auto] [Advance 900] [Advance 750ps] [Advance 600ps]
...[Advance 150] [Normal] [Delay 150ps] [Delay 300ps]...[Delay 900]
ꢂ-ꢀꢆ
Chapter ꢂ: BIOS setup
CPU FID/VID Control [Auto]
When set to [Auto], FID/VID will be set at the rated frequency/voltage. When set to
[Manual], FID/VID will be set based on the user selection.
Configuration options: [Auto] [Manual]
The following items appears only when you set the CPU FID/VID Control item
to [Auto].
Runtime Legacy PSB [Disabled]
Enables or disables the generation of Power State Block for the use of the
PowerNow™ driver in a single-core system.
Cool N’ Quiet [Disabled]
Enables or disables the generation of ACPI_PPC, ACPI_PSS, and ACPI_
PCT objects.
The following items appears only when you set the CPU FID/VID Control item to
[Auto] or set the AI Overclocking item to [EPP Memory].
CPU Multiplier [Auto]
Allows you to set the operating CPU multiplier. The configuration options may
vary depending on the type of CPU installed. Configuration options: [Auto]
[x5.0] [x5.5] [x6.0] [x6.5] [x7.0] [x7.5]...[x24.5] [x25.0]
CPU Voltage [Auto]
Allows you to set the operating CPU voltage.
Configuration options: [1.425V] [1.400V] [1.375V]...[0.825V] [0.800V] [Auto]
HyperTransport (CPU & CPU) [1000MHz]
Configuration options: [200 MHz] [400 MHz] [600 MHz] [800 MHz] [1000 MHz]
HyperTransport (CPU & SB1) [1000MHz]
Configuration options: [200 MHz] [400 MHz] [600 MHz] [800 MHz] [1000 MHz]
HyperTransport (CPU & SB2) [1000MHz]
Configuration options: [200 MHz] [400 MHz] [600 MHz] [800 MHz] [1000 MHz]
The following item appears only when you set the AI Overclocking item to
[Overclocking Profile] or [EPP Memory].
Overclock Options [Overclock 5%]
Allows you to overclock the CPU speed through the available preset values.
Configuration options: [Overclock 3%] [Overclock 5%] [Overclock 10%] [Overclock
15%] [Overclock 20%] [Overclock 30%]
ASUS LꢀNꢄꢂ-SLI WS
ꢂ-ꢀꢇ
The following items appear only when you set the AI Overclocking item to [EPP
Memory].
EPP Mode [Optimal]
Allows you to set the EPP mode.
Configuration options: [Optimal] [High Performance] [High Frequency]
CPU OC Percentage [100]
Allows you to adjust the CPU OC percentage. Use the <+> and <-> keys to adjust
the value. You can also type the desired value using the numeric keypad. The values
range from 100 to 200.
ꢂ-20
Chapter ꢂ: BIOS setup
4.4.2
CPU Configuration
The items in this menu show the CPU-related information that the BIOS
automatically detects.
CPU Configuration
Sets the ratio
between CPU Core
Clock and the FSB
Frequency.
NOTE: If an invalid
ratio is set in CMOS
then actual and
setpoint values may
differ.
AMD Engineering Sample
Revision: F2
Cache L1: 128KB
Cache L2: 2048KB
Speed
: 2815MHz
Current FSB Multiplier: 14x
Maximum FSB Multiplier: 25x
Able to Change Freq. : Yes
uCode Patch Level
: None Required
GART Error Reporting
[Disabled]
GART Error Reporting [Disabled]
Allows you to enable or disable GART error checking for testing purpose.
Configuration options: [Disabled] [Enabled]
ASUS LꢀNꢄꢂ-SLI WS
ꢂ-2ꢀ
4.4.3
Chipset
The Chipset menu allows you to change the advanced chipset settings. Select an
item then press <Enter> to display the sub-menu.
Advanced Chipset Settings
Memory Options &
Information
WARNING: Setting wrong values in below sections may
cause system to malfunction.
Memory Controller
SouthBridge Configuration
Memory Controller
Memory Options &
Information
Memory Setting: 533MHz-4.0-4-4-12-2T
Memclock Mode
CAS Latency (CL)
TRCD
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[2T]
[Auto]
[Auto]
[Auto]
TRP
TRAS
1T/2T Memory Timing
MCT Timing Mode
Bank Interleaving
Node Interleaving
DQS Signal Training Control [Enabled]
MemClk Tristate C3/ATLVID
CS Sparing Enable
[Disabled]
[Disabled]
[Enabled]
[Disabled]
Memory Hole Remapping
Power Down Control
Memclock Mode [Auto]
[Auto] allows the BIOS to set the memclock mode automatically. [Limit] or
[Manual] allows you to select from any of the standard values.
Configuration options: [Auto] [Limit] [Manual]
The following item appears when the Memclock Mode item is set to [Limit] or
[Manual].
Memclock Value [400 MHz]
Allows you to set the memclock value.
Configuration options: [400 MHz] [533 MHz] [667 MHz] [800 MHz]
ꢂ-22
Chapter ꢂ: BIOS setup
CAS Latency (CL) [Auto]
Configuration options: [Auto] [3.0] [4.0] [5.0] [6.0]
TRCD [Auto]
Configuration options: [Auto] [3 CLK] [4 CLK] [5 CLK] [6 CLK]
TRP [Auto]
Configuration options: [Auto] [3 CLK] [4 CLK] [5 CLK] [6 CLK]
TRAS [Auto]
Configuration options: [Auto] [5 CLK] [6 CLK] [7 CLK] [8 CLK]... [18 CLK]
1T/2T Memory Timing [2T]
Configuration options: [Auto] [1T] [2T]
MCT Timing Mode [Auto]
Allows you to manually configure the MCT Timing Mode parameters.
Configuration options: [Auto] [Manual]
The following items appear when the MCT Timing Mode item is set to [Manual].
TRRD [Auto]
Configuration options: [Auto] [2T] [3T] [4T] [5T]
TRC [Auto]
Configuration options: [Auto] [11T] [12T] [13T]...[25T] [26T]
Bank Interleaving [Auto]
Sets whether to allow memory accesses to be spread out over BANKS on the same
node or across nodes, decreasing access contention.
Configuration options: [Disabled] [Auto]
Node Interleaving [Auto]
Sets whether to allow memory accesses to be spread out over NODES on the same
node or across nodes, decreasing access contention.
Configuration options: [Disabled] [Auto]
DQS Signal Training Control [Disabled]
Enables or disable the DQS Signal Timing Training control.
Configuration options: [Enabled] [Disabled]
MemClk Tristate C3/ATLVID [Disabled]
Enables or disable the MemClk Tri-Stating during C3 and Alt VID.
Configuration options: [Enabled] [Disabled]
CS Sparing Enable [Disabled]
Configuration options: [Enabled] [Disabled]
Memory Hole Remapping [Enabled]
Enables or disable the memory remapping around the memory hole.
Configuration options: [Enabled] [Disabled]
Power Down Control [Disabled]
Allows DIMMs to enter the power down mode by deasserting the clock enable signal
when DIMMs are not in use.
Configuration options: [Auto ] [Disabled]
ASUS LꢀNꢄꢂ-SLI WS
ꢂ-2ꢁ
SouthBridge Chipset Configuration
Options
OnChip HD Audio
Front Panel Type
OnChip LAN1
[Enabled]
Enabled
Disabled
[AC97]
[Enabled]
[Enabled]
[Disabled]
OnChip LAN2
LAN OptionROM
SLI1 Optimization
SLI2 Optimization
[Enabled]
[Enabled]
OnChip HD Audio [Enabled]
Enables or disables the onchip high-definition audio CODEC.
Configuration options: [Enabled] [Disabled]
The following item appears when the OnChip HD Audio item is set to [Enabled] .
Front Panel Type [AC97]
Allows you to set the front panel audio connector (AAFP) mode to legacy AC’97 or high-
definition audio depending on the audio standard that the front panel audio module supports.
Configuration options: [AC97] [HD Audio]
OnChip LAN1/LAN2 [Enabled]
Enables or disables the onchip LAN1/LAN2 controller.
Configuration options: [Enabled] [Disabled]
LAN OptionROM [Disabled]
Enables or disables the LAN boot ROM.
Configuration options: [Enabled] [Disabled]
SLI1/SLI2 Optimization [Enabled]
Configuration options: [Enabled] [Disabled]
ꢂ-2ꢂ
Chapter ꢂ: BIOS setup
4.4.4
Onboard Devices Configuration
Configure ITE8712 Super IO Chipset
Allows BIOS to Enable
or Disable Floppy
Controller.
Onboard Floppy Controller
[Enabled]
[3F8/IRQ4]
[378]
Serial Port1 Address
Parallel Port Address
Parallel Port Mode
EPP Version
[EPP+ECP]
[1.9]
ECP Mode DMA Channel
Parallel Port IRQ
[DMA3]
[IRQ7]
Configure Onboard Device
OnBoard VT6308 1394
OnBoard Sil3531 eSATA
eSATA OptionROM
[Enabled]
[Enabled]
[Disabled]
Onboard Floppy Controller [Enabled]
Allows you to enable or disable the onboard floppy controller
Configuration options: [Enabled] [Disabled]
Serial Port1 Address [3F8/IRQ4]
Allows you to select the Serial Port1 base address.
Configuration options: [Disabled] [3F8/IRQ4] [2F8/IRQ3] [3E8/IRQ4] [2E8/IRQ3]
Parallel Port Address [378]
Allows you to select the Parallel Port base address.
Configuration options: [Disabled] [378] [278]
Parallel Port Mode [EPP+ECP]
Allows you to select the Parallel Port mode.
Configuration options: [Normal] [EPP] [ECP] [EPP+ECP]
EPP Version [1.9]
Appears only when the Parallel Port Mode is set to [EPP] or [EPP+ECP]. This item allows the
BIOS to select the Parallel Port EPP version.
Configuration options: [1.9] [1.7]
ECP Mode DMA Channel [DMA3]
Appears only when the Parallel Port Mode is set to [ECP] or [EPP+ECP]. This item allows the
BIOS to set the Parallel Port ECP DMA.
Configuration options: [DMA0] [DMA1] [DMA3]
Parallel Port IRQ [IRQ7]
Allows you to select the parallel port IRQ.
Configuration options: [IRQ5] [IRQ7]
ASUS LꢀNꢄꢂ-SLI WS
ꢂ-2ꢃ
OnBoard VT6308 1394 [Enabled]
Allows you to enable or disable the onboard VIA® VT6308 IEEE 1394a controller.
Configuration options: [Enabled] [Disabled]
OnBoard Sil3531 eSATA [Enabled]
Allows you to enable or disable the onboard Silicon Image® Sil3531 external SATA
controller. Configuration options: [Enabled] [Disabled]
eSATA OptionROM [Disabled]
Allows you to enable or disable the Silicon Image® Sil3531 external SATA boot ROM.
Configuration options: [Disabled] [Enabled]
ꢂ-2ꢄ
Chapter ꢂ: BIOS setup
4.4.5
PCI PnP
The PCI PnP menu items allow you to change the advanced settings for PCI/PnP
devices.
Advanced PCI/PnP Settings
NO: lets the BIOS
configue all the
WARNING: Setting wrong values in below sections
may cause system to malfunction.
devices in the system.
YES: lets the
Plug And Play O/S
[No]
operating system
configure Plug and Play
(PnP) devices not
required for boot if
your system has a Plug
and Play operating
system.
Plug And Play O/S [No]
When set to [No], BIOS configures all the devices in the system. When set to
[Yes] and if you install a Plug and Play operating system, the operating system
configures the Plug and Play devices not required for boot. Configuration options:
[No] [Yes]
ASUS LꢀNꢄꢂ-SLI WS
ꢂ-2ꢅ
4.4.6
USB Configuration
The items in this menu allows you to change the USB-related features. Select an
item then press <Enter> to display the configuration options.
USB Configuration
Options
Module Version - 2.24.0-12.4
Enabled
Disabled
USB Devices Enabled:
None
USB 1.1 Controller
USB 2.0 Controller
Legacy USB Support
USB 2.0 Controller Mode
BIOS EHCI Hand-off
[Enabled]
[Enabled]
[Enabled]
[HiSpeed]
[Enabled]
The Module Version and USB Devices Enabled items show the
auto-detected values. If no USB device is detected, the item shows None.
USB 1.1 Controller [Enabled]
Allows you to enable or disable the USB 1.1 controller.
Configuration options: [Enabled] [Disabled]
The following item appears only when the USB 1.1 Controller is set to
[Enabled].
USB 2.0 Controller [Enabled]
Allows you to enable or disable the USB 2.0 controller.
Configuration options: [Enabled] [Disabled]
Legacy USB Support [Enabled]
Allows you to enable or disable support for legacy USB devices. Setting to [Auto]
allows the system to detect the presence of USB devices at startup. If detected,
the USB controller legacy mode is enabled. If no USB device is detected, the
legacy USB support is disabled.
Configuration options: [Disabled] [Enabled] [Auto]
USB 2.0 Controller Mode [HiSpeed]
Allows you to set the USB 2.0 controller mode to HiSpeed (480 Mbps) or
FullSpeed (12 Mbps). Configuration options: [FullSpeed] [HiSpeed]
BIOS EHCI Hand-off [Enabled]
Allows you to enable support for operating systems without an EHCI hand-off
feature. Configuration options: [Disabled] [Enabled]
ꢂ-2ꢆ
Chapter ꢂ: BIOS setup
4.5
Power menu
The Power menu items allow you to change the settings for the ACPI and
Advanced Power Management (APM) features. Select an item then press <Enter>
to display the configuration options.
BIOS SETUP UTILITY
Main
Advanced
Power
Boot
Tools
Exit
Suspend Mode
ACPI 2.0 Support
ACPI APIC Support
[Auto]
[ACPI v1.0]
[Enabled]
Select the ACPI state
used for System
Suspend.
APM Configuration
Hardware Monitor
Select Screen
Select Item
Change Field
General Help
Save and Exit
Exit
+-
F1
F10
ESC
v02.58 (C)Copyright 1985-2006, American Megatrends, Inc.
4.5.1
Suspend Mode [Auto]
Allows you to select the Advanced Configuration and Power Interface (ACPI) state
to be used for system suspend. Setting this item to [Auto] allows the OS to select the
ACPI state. Configuration options: [S1 (POS) only] [S3 only] [Auto]
4.5.2
ACPI 2.0 Support [ACPI v1.0]
Allows you to add more tables for Advanced Configuration and Power Interface
(ACPI) 2.0 specifications. Configuration options: [ACPI v1.0] [ACPI v2.0] [ACPI
v3.0]
4.5.3
ACPI APIC Support [Enabled]
Allows you to enable or disable the Advanced Configuration and Power Interface
(ACPI) support in the Advanced Programmable Interrupt Controller (APIC). When
set to Enabled, the ACPI APIC table pointer is included in the RSDT pointer list.
Configuration options: [Disabled] [Enabled]
ASUS LꢀNꢄꢂ-SLI WS
ꢂ-2ꢇ
4.5.4
APM Configuration
APM Configuration
Options
Restore on AC Power Loss
Power Management/APM
Resume On PME#
[Power Off]
[Enabled]
Power Off
Power On
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
Resume On PCIE Wake#
Resume On LAN
Resume On Ring
Resume On PS/2 Keyboard
Resume On PS/2 Mouse
Resume On RTC Alarm
Restore on AC Power Loss [Power Off]
When set to Power Off, the system goes into off state after an AC power loss.
When set to Power On, the system goes on after an AC power loss. When set to
Last State, the system goes into either off or on state, whatever the system state
was before the AC power loss.
Configuration options: [Power Off] [Power On]
Power Management/APM [Enabled]
Enables or disables the Advanced Power Management (APM) features.
Configuration options: [Disabled] [Enabled]
The succeeding items appear when the Power Management/APM item is set to
[Enabled].
Resume On PME# [Disabled]
Enables or disables the Power Management Event (PME) function to generate a
wake event. Configuration options: [Disabled] [Enabled]
Resume On PCIE Wake# [Disabled]
Enables or disables the PME to wake up from S5 by PCIE devices.
Configuration options: [Disabled] [Enabled]
Resume On LAN [Disabled]
Enables or disables the Marvell® LAN to generate a wake event.
Configuration options: [Disabled] [Enabled]
Resume On Ring [Disabled]
Enables or disables the RI to generate a wake event.
Configuration options: [Disabled] [Enabled]
ꢂ-ꢁ0
Chapter ꢂ: BIOS setup
Resume On PS/2 Keyboard [Disabled]
Allows you to use specific keys on the keyboard to turn on the system. This
feature requires an ATX power supply that provides at least 1A on the +5VSB lead.
Configuration options: [Disabled] [Enabled]
Resume On PS/2 Mouse [Disabled]
When set to [Enabled], this parameter allows you to use the PS/2 mouse to turn on
the system. This feature requires an ATX power supply that provides at least 1A on
the +5VSB lead. Configuration options: [Disabled] [Enabled]
Resume on RTC Alarm [Disabled]
Allows you to enable or disable RTC to generate a wake event. Configuration
options: [Disabled] [Enabled]
The succeeding items appear when the Resume on RTC Alarm item is set to
[Enabled].
RTC Alarm Date [xx]
To set the alarm date, highlight this item and press the <+> or <-> key to
make the selection. Configuration options: [Every day] [1] [2] [3]... ~ [31]
System Time [xx:xx:xx]
To set the alarm time, use [ENTER], [TAB], or [SHIFT-TAB] ro select a field
and press the <+> or <-> key to make the selection.
Configuration options: [00] [01]... ~ [23]
[00] [01]... ~ [59]
[00] [01]... ~ [59]
ASUS LꢀNꢄꢂ-SLI WS
ꢂ-ꢁꢀ
4.5.5
Hardware Monitor
Hardware Monitor
CPU Temperature
CPU1 Temperature
CPU2 Temperature
MB Temperature
[60ºC/140ºF]
[60ºC/140ºF]
[46ºC/114.5ºF]
Smart Fan Control
CPU Fan Mode
[Disabled]
[PWM]
CPU Fan1 Speed
CPU Fan2 Speed
CHA Fan1 Speed
CHA Fan2 Speed
SPS Fan Speed
HP Fan3 Speed
[2564RPM]
[4354RPM]
[N/A]
[N/A]
[4655RPM]
VCORE1 Voltage
VCORE2 Voltage
3.3V Voltage
5V Voltage
[ 1.440V]
[ 1.440V]
[ 2.992V]
[ 4.889V]
[10.579V]
12V Voltage
CPU1/CPU2 Temperature [xxxºC/xxxºF]
MB Temperature [xxxºC/xxxºF]
The onboard hardware monitor automatically detects and displays the motherboard
and CPU temperatures. Select [Disabled] if you do not wish to display the detected
temperatures.
Smart Fan Control [Disabled]
Allows you to enable or disable the smart fan feature that smartly adjusts the fan
speeds for more efficient system operation. Configuration options: [Disabled]
[Enabled]
CPU Fan Mode [PWM]
Allows you to select the type of CPU fan cable connected to the CPU fan
connector. Set to [PWM] when using a 4-pin CPU fan cable. Set to [DC] when
using a 3-pin CPU fan cable. Configuration options: [PWM] [DC]
Some CPU fans with a 4-pin cable do not comply with Intel®’s PWM fan
specification. When using this type of CPU fan, you can not reduce the CPU fan
speed even if you set the CPU Q-Fan Mode to [PWM].
CPU Fan1/Fan2 Speed (RPM) [xxxxRPM] or [N/A] or [Ignored]
The onboard hardware monitor automatically detects and displays the CPU
fan speed in rotations per minute (RPM). If the fan is not connected to the
motherboard, the field shows N/A. Select [Ignore] from the item options to disable
CPU fan speed monitoring.
ꢂ-ꢁ2
Chapter ꢂ: BIOS setup
CHA Fan1/Fan2 Speed (RPM) [xxxxRPM] or [N/A] or [Ignored]
The onboard hardware monitor automatically detects and displays the chassis fan
speed in rotations per minute (RPM). If the fan is not connected to the chassis, the
specific field shows N/A. Select [Ignore] from the item options to disable chassis
fan speed monitoring.
SPS Fan/HP Fan3 Speed (RPM) [xxxxRPM] or [N/A] or [Ignored]
The onboard hardware monitor automatically detects and displays the SPS/
Heatpipe fan speed in rotations per minute (RPM). If the fan is not connected to
the chassis, the specific field shows N/A. Select [Ignore] from the item options to
disable chassis fan speed monitoring.
VCORE1/VCORE2 Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage
The onboard hardware monitor automatically detects the voltage output through
the onboard voltage regulators.
ASUS LꢀNꢄꢂ-SLI WS
ꢂ-ꢁꢁ
4.6
Boot menu
The Boot menu items allow you to change the system boot options. Select an item
then press <Enter> to display the sub-menu.
BIOS SETUP UTILITY
Main
Advanced
Power
Boot
Tools
Exit
Specifies the Boot
Device Priority
sequence.
Boot Device Priority
Boot Settings Configuration
Security
A virtual floppy disk
drive (Floppy Drive
B:) may appear when
you set the CD-ROM
drive as the first
boot device.
Select Screen
Select Item
Enter Go to Sub Screen
F1
F10
ESC
General Help
Save and Exit
Exit
v02.58 (C)Copyright 1985-2006, American Megatrends, Inc.
4.6.1
Boot Device Priority
Specifies the boot
Boot Device Priority
sequence from the
available devices.
1st Boot Device
2nd Boot Device
3rd Boot Device
[1st FLOPPY DRIVE]
[HDD: PM-ST330620A]
[ATAPI CD-ROM]
A device enclosed
in parenthesis has
been disable din the
corresponding type
menu.
1st ~ xxth Boot Device [1st FLOPPY DRIVE]
These items specify the boot device priority sequence from the available devices.
The number of device items that appears on the screen depends on the number of
devices installed in the system.
Configuration options: [1st FLOPPY DRIVE] [HDD:xxxxxx] [ATAPI CDROM]
[Disabled]
ꢂ-ꢁꢂ
Chapter ꢂ: BIOS setup
4.6.2
Boot Settings Configuration
Boot Settings Configuration
Allows BIOS to skip
certain tests while
booting. This will
decrease the time
needed to boot the
system.
Quick Boot
Full Screen Logo
AddOn ROM Display Mode
Bootup Num-Lock
PS/2 Mouse Support
Wait For ‘F1’ If Error
Hit ‘DEL’ Message Display
Interrupt 19 Capture
[Enabled]
[Enabled]
[Force BIOS]
[On]
[Auto]
[Enabled]
[Enabled]
[Disabled]
Quick Boot [Enabled]
Enabling this item allows the BIOS to skip some power on self tests (POST) while
booting to decrease the time needed to boot the system. When set to [Disabled],
BIOS performs all the POST items.
Configuration options: [Disabled] [Enabled]
Full Screen Logo [Enabled]
Allows you to enable or disable the full screen logo display feature.
Configuration options: [Disabled] [Enabled]
AddOn ROM Display Mode [Force BIOS]
Sets the display mode for option ROM.
Configuration options: [Force BIOS] [Keep Current]
Bootup Num-Lock [On]
Allows you to select the power-on state for the NumLock.
Configuration options: [Off] [On]
PS/2 Mouse Support [Auto]
Allows you to enable or disable support for PS/2 mouse.
Configuration options: [Disabled] [Enabled] [Auto]
Wait for ‘F1’ If Error [Enabled]
When set to Enabled, the system waits for the F1 key to be pressed when error
occurs. Configuration options: [Disabled] [Enabled]
Hit ‘DEL’ Message Display [Enabled]
When set to Enabled, the system displays the message “Press DEL to run Setup”
during POST. Configuration options: [Disabled] [Enabled]
Interrupt 19 Capture [Disabled]
When set to [Enabled], this function allows the option ROMs to trap Interrupt 19.
Configuration options: [Disabled] [Enabled]
ASUS LꢀNꢄꢂ-SLI WS
ꢂ-ꢁꢃ
4.6.3
Security
The Security menu items allow you to change the system security settings. Select
an item then press <Enter> to display the configuration options.
Security Settings
<Enter> to change
password.
<Enter> again to
disabled password.
Supervisor Password
User Password
: Not Installed
: Not Installed
Change Supervisor Password
Change User Password
Select Screen
Select Item
Enter Change
F1
F10
ESC
General Help
Save and Exit
Exit
Change Supervisor Password
Select this item to set or change the supervisor password. The Supervisor
Password item on top of the screen shows the default Not Installed. After you set a
password, this item shows Installed.
To set a Supervisor Password:
1.
2.
Select the Change Supervisor Password item, then press <Enter>.
From the password box, type a password composed of at least six letters
and/or numbers, then press <Enter>.
3.
Confirm the password when prompted.
The message “Password Installed” appears after you successfully set your
password.
To change the supervisor password, follow the same steps as in setting a user
password.
To clear the supervisor password, select the Change Supervisor Password then press
<Enter>. The message “Password Uninstalled” appears.
If you forget your BIOS password, you can clear it by erasing the CMOS Real
Time Clock (RTC) RAM. See section “2.6 Jumper” for information on how to
erase the RTC RAM.
ꢂ-ꢁꢄ
Chapter ꢂ: BIOS setup
After you have set a supervisor password, the other items appear to allow you to
change other security settings.
Security Settings
Supervisor Password
User Password
: Not Installed
: Not Installed
Change Supervisor Password
User Access Level
Change User Password
Clear User Password
Password Check
[Full Access]
[Setup]
Select Screen
Select Item
Enter Change
F1
F10
ESC
General Help
Save and Exit
Exit
User Access Level [Full Access]
This item allows you to select the access restriction to the Setup items.
Configuration options: [No Access] [View Only] [Limited] [Full Access]
No Access prevents user access to the Setup utility.
View Only allows access but does not allow change to any field.
Limited allows changes only to selected fields, such as Date and Time.
Full Access allows viewing and changing all the fields in the Setup utility.
Change User Password
Select this item to set or change the user password. The User Password item on
top of the screen shows the default Not Installed. After you set a password, this
item shows Installed.
To set a User Password:
1.
2.
Select the Change User Password item and press <Enter>.
On the password box that appears, type a password composed of at least six
letters and/or numbers, then press <Enter>.
3.
Confirm the password when prompted.
The message “Password Installed” appears after you set your password
successfully.
To change the user password, follow the same steps as in setting a user password.
ASUS LꢀNꢄꢂ-SLI WS
ꢂ-ꢁꢅ
Clear User Password
Select this item to clear the user password.
Password Check [Setup]
When set to [Setup], BIOS checks for user password when accessing the Setup
utility. When set to [Always], BIOS checks for user password both when accessing
Setup and booting the system.
Configuration options: [Setup] [Always]
ꢂ-ꢁꢆ
Chapter ꢂ: BIOS setup
4.7
Exit menu
The Exit menu items allow you to load the optimal or failsafe default values for the
BIOS items, and save or discard your changes to the BIOS items.
BIOS SETUP UTILITY
Main
Advanced
Power
Boot
Exit
Exit Options
Exit & Save Changes
Exit & Discard Changes
Discard Changes
Load Setup Defaults
Select Screen
Select Item
Enter Go to Sub Screen
F1
F10
ESC
General Help
Save and Exit
Exit
v02.58 (C)Copyright 1985-2006, American Megatrends, Inc.
Pressing <Esc> does not immediately exit this menu. Select one of the options
from this menu or <F10> from the legend bar to exit.
Exit & Save Changes
Once you are finished making your selections, choose this option from the Exit
menu to ensure the values you selected are saved to the CMOS RAM. An onboard
backup battery sustains the CMOS RAM so it stays on even when the computer is
turned off. When you select this option, a confirmation window appears. Select OK
to save the changes and exit.
If you attempt to exit the Setup program without saving your changes, the
program prompts you with a message asking if you want to save your changes
before exiting. Press <Enter> to save the changes while exiting.
Exit & Discard Changes
Select this option only if you do not want to save the changes that you made to
the Setup program. If you made changes to fields other than System Date, System
Time, and Password, the BIOS asks for a confirmation before exiting.
Discard Changes
Allows you to discard the selections you made and restore the previously saved
values. After selecting this option, a confirmation appears. Select Ok to discard any
changes and load the previously saved values.
ASUS LꢀNꢄꢂ-SLI WS
ꢂ-ꢁꢇ
Load Setup Defaults
Allows you to load the default values for each of the parameters on the Setup
menus. When you select this option or if you press <F5>, a confirmation window
appears. Select Ok to load default values. Select Exit & Save Changes or make
other changes before saving the values to the non-volatile RAM.
ꢂ-ꢂ0
Chapter ꢂ: BIOS setup
This chapter describes the contents
of the support CD that comes with the
motherboard package.
Software
5
support
Chapter summary
5
5.1
5.2
Installing an operating system ................................................... 5-1
Support CD information .............................................................. 5-1
ASUS L1N64-SLI WS
5.1
Installing an operating system
This motherboard supports Windows® 2000/2003 Server/XP/64-bit XP operating
systems (OS). Always install the latest OS version and corresponding updates to
maximize the features of your hardware.
•
Motherboard settings and hardware options vary. Use the setup
procedures presented in this chapter for reference only. Refer to your OS
documentation for detailed information.
•
Make sure that you install Windows® 2000 Service Pack 4 or the Windows®
XP Service Pack2 or later versions before installing the drivers for better
compatibility and system stability.
5.2
Support CD information
The support CD that came with the motherboard package contains the drivers,
software applications, and utilities that you can install to avail all motherboard
features.
The contents of the support CD are subject to change at any time without
notice. Visit the ASUS website(www.asus.com) for updates.
5.2.1
Running the support CD
Place the support CD to the optical drive. The CD automatically displays the
Drivers menu if Autorun is enabled in your computer.
Click an icon to display
support CD/motherboard
information
Click an item to install
If Autorun is NOT enabled in your computer, browse the contents of the support
CD to locate the file ASSETUP.EXE from the BIN folder. Double-click the
ASSETUP.EXE to run the CD.
ASUS LꢀNꢄꢂ-SLI WS
ꢃ-ꢀ
5.2.2
Drivers menu
The drivers menu shows the available device drivers if the system detects installed
devices. Install the necessary drivers to activate the devices.
Nvidia Chipset Driver Program
Installs the NVIDIA® Chipset drivers for the NVIDIA® nForce® 680a SLI chipset.
AMD Cool ‘n’ Quiet Driver
Installs the AMD Cool ‘n’ Quiet™ technology driver.
SoundMAX ADI1988 Audio Driver
Installs the SoundMAX® ADI1988 audio driver and application.
Silicon Image Sil3531 SATA Driver and Utility
Installs the Silicon Image® Sil3531 SATA driver and utility.
USB 2.0 Driver
Installs the Universal Serial Bus 2.0 (USB 2.0) driver.
ꢃ-2
Chapter ꢃ: Software support
5.2.3
Utilities menu
The Utilities menu shows the applications and other software that the motherboard
supports.
ASUS Cool ‘n’ Quiet Utility
Installs the AMD Cool ‘n’ Quiet™ software.
ASUS Update
The ASUS Update utility allows you to update the motherboard BIOS in Windows®
environment. This utility requires an Internet connection either through a network
or an Internet Service Provider (ISP).
Adobe Acrobat Reader V7.0
Installs the Adobe® Acrobat® Reader that allows you to open, view, and print
documents in Portable Document Format (PDF).
Microsoft DirectX 9.0c
Installs the Microsoft® DirectX 9.0c driver. The Microsoft DirectX® 9.0c is a
multimedia technology that enhances computer graphics and sound. DirectX®
improves the multimedia features of you computer so you can enjoy watching
TV and movies, capturing videos, or playing games in your computer. Visit the
Microsoft website (www.microsoft.com) for updates.
Anti-virus Utility
The anti-virus application scans, identifies, and removes computer viruses. View
the online help for detailed information.
ASUS LꢀNꢄꢂ-SLI WS
ꢃ-ꢁ
5.2.4
Make Disk menu
The Make Disk menu contains items to create the NVIDIA® nForce® 680a or Silicon
Image SATA/PATA RAID driver disk.
Make nVidia 32bit/64bit SATA RAID Driver
Allows you to create an NVIDIA® Serial ATA RAID driver disk for a 32-bit/64-bit
system.
Silicon Image Sil3531 32bit/64bit SATA Driver
Allows you to create a Silicon Image® Sil3531 Serial ATA driver disk for a 32-bit/64-
bit system.
ꢃ-ꢂ
Chapter ꢃ: Software support
5.2.5
Manuals menu
The Manuals menu contains a list of supplementary user manuals. Click an item to
open the folder of the user manual.
Most user manual files are in Portable Document Format (PDF). Install the
Adobe® Acrobat® Reader from the Utilities menu before opening a user manual
file.
5.2.6
ASUS Contact information
Click the Contact tab to display the ASUS contact information. You can also find
this information on the inside front cover of this user guide.
ASUS LꢀNꢄꢂ-SLI WS
ꢃ-ꢃ
5.2.7
Other information
The icons on the top right corner of the screen give additional information on the
motherboard and the contents of the support CD. Click an icon to display the
specified information.
Motherboard Info
Displays the general specifications of the motherboard.
Browse this CD
Displays the support CD contents in graphical format.
ꢃ-ꢄ
Chapter ꢃ: Software support
Technical support Form
Displays the ASUS Technical Support Request Form that you have to fill out when
requesting technical support.
Filelist
Displays the contents of the support CD in text format.
ASUS LꢀNꢄꢂ-SLI WS
ꢃ-ꢅ
ꢃ-ꢆ
Chapter ꢃ: Software support
|