Asus Computer Monitor VW223 User Manual

VW223 Series  
LCD Monitor  
User Guide  
Contents  
iii  
 
Notices  
Federal Communications Commission Statement  
This device complies with Part 15 of the FCC Rules. Operation is subject to the  
following two conditions:  
This device may not cause harmful interference, and  
This device must accept any interference received including interference that  
may cause undesired operation.  
This equipment has been tested and found to comply with the limits for a  
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against harmful interference in a  
residential installation. This equipment generates, uses and can radiate radio  
frequency energy and, if not installed and used in accordance with manufacturer’s  
instructions, may cause harmful interference to radio communications. However,  
there is no guarantee that interference will not occur in a particular installation. If  
this equipment does cause harmful interference to radio or television reception,  
which can be determined by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one or more of the following  
measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment to an outlet on a circuit different from that to which the  
receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
The use of shielded cables for connection of the monitor to the graphics card is  
required to assure compliance with FCC regulations. Changes or modifications  
to this unit not expressly approved by the party responsible for compliance  
could void the user’s authority to operate this equipment.  
As an Energy Star® Partner, our company has determined that this product meets  
the Energy Star® guidelines for energy efficiency.  
Canadian Department of Communications Statement  
This digital apparatus does not exceed the Class B limits for radio noise emissions  
from digital apparatus set out in the Radio Interference Regulations of the  
Canadian Department of Communications.  
This class B digital apparatus complies with Canadian ICES-003.  
iv  
 
TCO Development  
Congratulations!  
The display you have just purchased carries the  
TCO’03 Displays label. This means that your  
display is designed, manufactured and tested  
according to some of the strictest quality and  
environmental requirements in the world. This  
makes for a high performance product, designed  
with the user in focus that also minimizes the  
impact on our natural environment.  
Some of the features of the TCO’03 Display requirements:  
Ergonomics  
Good visual ergonomics and image quality in order to improve the working  
environment for the user and to reduce sight and strain problems. Important  
parameters are luminance, contrast, resolution, reflectance, colour rendition  
and image stability.  
Energy  
Energy-saving mode after a certain time – beneficial both for the user and the  
environment  
Electrical safety  
Emissions  
Electromagnetic fields  
Noise emissions  
Ecology  
The product must be prepared for recycling and the manufacturer must have a  
certified environmental management system such as EMAS or ISO 14 001  
Restrictions on  
- chlorinated and brominated flame retardants and polymers  
- heavy metals such as cadmium, mercury and lead.  
The requirements included in this label have been developed by TCO  
Development in cooperation with scientists, experts, users as well as  
manufacturers all over the world. Since the end of the 1980s TCO has been  
involved in influencing the development of IT equipment in a more user-friendly  
direction. Our labelling system started with displays in 1992 and is now requested  
by users and IT-manufacturers all over the world.  
v
Safety information  
Before setting up the monitor, carefully read all the documentation that came  
with the package.  
To prevent fire or shock hazard, never expose the monitor to rain or moisture.  
Never try to open the monitor cabinet. The dangerous high voltages inside the  
monitor may result in serious physical injury.  
If the power supply is broken, do not try to fix it by yourself. Contact a qualified  
service technician or your retailer.  
Before using the product, make sure all cables are correctly connected and the  
power cables are not damaged. If you detect any damage, contact your dealer  
immediately.  
Slots and openings on the back or top of the cabinet are provided for  
ventilation. Do not block these slots. Never place this product near or over a  
radiator or heat source unless proper ventilation is provided.  
The monitor should be operated only from the type of power source indicated  
on the label. If you are not sure of the type of power supply to your home,  
consult your dealer or local power company.  
Use the appropriate power plug which complies with your local power  
standard.  
Do not overload power strips and extention cords. Overloading can result in  
fire or electric shock.  
Avoid dust, humidity, and temperature extremes. Do not place the monitor in  
any area where it may become wet. Place the monitor on a stable surface.  
Unplug the unit during a lightning storm or if it will not be used for a long period  
of time. This will protect the monitor from damage due to power surges.  
Never push objects or spill liquid of any kind into the slots on the monitor  
cabinet.  
To ensure satisfactory operation, use the monitor only with UL listed  
computers which have appropriate configured receptacles marked between  
100-240V AC.  
If you encounter technical problems with the monitor, contact a qualified  
service technician or your retailer.  
This symbol of the crossed out wheeled bin indicates that the product (electrical  
and electronic equipment) should not be placed in municipal waste.  
Please check local regulations for disposal of electronic products.  
vi  
 
Care & Cleaning  
Before you lift or reposition your monitor, it is better to disconnect the cables  
and power cord. Follow the correct lifting techniques when positioning the  
monitor. When lifting or carrying the monitor, grasp the edges of the monitor.  
Do not lift the display by the stand or the cord.  
Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor  
surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed  
with a cloth dampened with mild cleaner.  
Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended  
for use with the LCD. Never spray cleaner directly on the screen, as it may drip  
inside the monitor and cause an electric shock.  
The following symptoms are normal with the monitor:  
The screen may flicker during the initial use due to the nature of the fluorescent  
light. Turn off the Power Switch and turn it on again to make sure that the  
flicker disappears.  
You may find slightly uneven brightness on the screen depending on the  
desktop pattern you use.  
When the same image is displayed for hours, an afterimage of the previous  
screen may remain after switching the image. The screen will recover slowly or  
you can turn off the Power Switch for hours.  
When the screen becomes black or flashes, or cannot work anymore, contact  
your dealer or service center to fix it. Do not repair the screen by yourself!  
Conventions used in this guide  
To make sure that you perform certain tasks properly, take note of the following  
symbols used throughout this manual.  
DANGER/WARNING: Information to prevent injury to yourself  
when trying to complete a task.  
CAUTION: Information to prevent damage to the components  
when trying to complete a task.  
IMPORTANT: Instructions that you MUST follow to complete a  
task.  
NOTE: Tips and additional information to help you complete a  
task.  
vii  
 
Where to find more information  
Refer to the following sources for additional information and for product and  
software updates.  
1.  
2.  
ASUS websites  
The ASUS websites worldwide provide updated information on ASUS  
Optional documentation  
Your product package may include optional documentation that may have  
been added by your dealer. These documents are not part of the standard  
package.  
viii  
1.1  
Welcome!  
Thank you for purchasing the ASUS® VW223 Series LCD monitor!  
The latest widescreen LCD monitor from ASUS provides a crisper, broader, and  
brighter display, plus a host of features that enhance your viewing experience.  
With these features, you can enjoy the convenience and delightful visual  
experience that the VW223 Series brings you!  
1.2  
Package contents  
Check your VW223 Series LCD monitor package for the following items:  
LCD monitor  
Monitor base  
Quick start guide  
Power cord x1  
VGA cable x1  
Support CD (For VW223B only)  
USB cable x1 (For VW223B only)  
DVI cable x1 (For VW223N / VW223T only)  
Audio cable x1 (For VW223S / VW223T only)  
If any of the above items is damaged or missing, contact your retailer  
immediately.  
ASUS VW223 Series LCD Monitor  
1-1  
 
1.3  
Monitor introduction  
1.3.1  
Front view  
VW223B  
Base  
4
5
6
1
2
3
1.  
Button:  
Use this hotkey to switch from five video preset modes (Scenery Mode,  
Standard Mode, Theater Mode, Game Mode, Night View Mode) with  
SPLENDID™ Video Enhancement Technology.  
Exit the OSD menu or go back to the previous menu as the OSD menu  
is active.  
Automatically adjust the image to its optimized position, clock, and phase  
by pressing this button for 2-4 seconds (for VGA mode only).  
2.  
Button:  
Press this button to decrease the value of the function selected or move  
left/down to the previous function.  
This is also a hotkey for Contrast adjustment.  
3.  
4.  
MENU Button:  
Press this button to enter/select the icon (function) highlighted while the  
OSD is activated.  
Button:  
Press this button to increase the value of the function selected or move  
right/up to the previous function.  
This is also a hotkey for Brightness adjustment.  
Button:  
5.  
Use this hotkey to switch between the input sources (VGA and ASUS  
EzLink Display).  
1-2  
Chapter 1: Product introduction  
 
6.  
Power Button / Power Indicator:  
Press this button to turn the monitor on/off  
The color definition of the power indicator is as the below table.  
Status  
Blue  
Description  
ON  
Amber  
OFF  
Standby mode  
OFF  
VW223S  
1
2
4
5
6
3
1.  
Button:  
Use this hotkey to switch from five video preset modes (Scenery Mode,  
Standard Mode, Theater Mode, Game Mode, Night View Mode) with  
SPLENDID™ Video Enhancement Technology.  
Exit the OSD menu or go back to the previous menu as the OSD menu  
is active.  
2.  
Button:  
Press this button to decrease the value of the function selected or move  
left/down to the next function.  
This is also a hotkey for Volume adjustment.  
3.  
4.  
MENU Button:  
Press this button to enter/select the icon (function) highlighted while the  
OSD is activated.  
Button:  
Press this button to increase the value of the function selected or move  
right/up to the previous function.  
This is also a hotkey for Brightness adjustment.  
Button:  
5.  
6.  
Automatically adjust the image to its optimized position, clock, and phase  
by pressing this button for 2-4 seconds.  
Power Button / Power Indicator:  
Press this button to turn the monitor on/off  
The color definition of the power indicator is as VW223B.  
ASUS VW223 Series LCD Monitor  
1-3  
VW223D  
4
5
6
1
2
3
1.  
2.  
Button:  
Use this hotkey to switch from five video preset modes (Scenery Mode,  
Standard Mode, Theater Mode, Game Mode, Night View Mode) with  
SPLENDID™ Video Enhancement Technology.  
Exit the OSD menu or go back to the previous menu as the OSD menu  
is active.  
Button:  
Press this button to decrease the value of the function selected or move  
left/down to the previous function.  
This is also a hotkey for Contrast adjustment.  
3.  
4.  
MENU Button:  
Press this button to enter/select the icon (function) highlighted while the  
OSD is activated.  
Button:  
Press this button to increase the value of the function selected or move  
right/up to the previous function.  
This is also a hotkey for Brightness adjustment.  
Button:  
5.  
6.  
Automatically adjust the image to its optimized position, clock, and phase  
by pressing this button for 2-4 seconds.  
Power Button / Power Indicator:  
Press this button to turn the monitor on/off  
The color definition of the power indicator is as VW223B.  
1-4  
Chapter 1: Product introduction  
VW223N  
4
5
6
1
2
3
1.  
Button:  
Use this hotkey to switch from five video preset modes (Scenery Mode,  
Standard Mode, Theater Mode, Game Mode, Night View Mode) with  
SPLENDID™ Video Enhancement Technology.  
Exit the OSD menu or go back to the previous menu as the OSD menu  
is active.  
Automatically adjust the image to its optimized position, clock, and phase  
by pressing this button for 2-4 seconds (for VGA mode only).  
2.  
Button:  
Press this button to decrease the value of the function selected or move  
left/down to the previous function.  
This is also a hotkey for Contrast adjustment.  
3.  
4.  
MENU Button:  
Press this button to enter/select the icon (function) highlighted while the  
OSD is activated.  
Button:  
Press this button to increase the value of the function selected or move  
right/up to the previous function.  
This is also a hotkey for Brightness adjustment.  
Button:  
5.  
6.  
Use this hotkey to switch between the input sources (VGA and DVI).  
Power Button / Power Indicator:  
Press this button to turn the monitor on/off  
The color definition of the power indicator is as VW223B.  
ASUS VW223 Series LCD Monitor  
1-5  
VW223T  
4
5
6
1
2
3
1.  
Button:  
Use this hotkey to switch from five video preset modes (Scenery Mode,  
Standard Mode, Theater Mode, Game Mode, Night View Mode) with  
SPLENDID™ Video Enhancement Technology.  
Exit the OSD menu or go back to the previous menu as the OSD menu  
is active.  
Automatically adjust the image to its optimized position, clock, and phase  
by pressing this button for 2-4 seconds (for VGA mode only).  
2.  
Button:  
Press this button to decrease the value of the function selected or move  
left/down to the next function.  
This is also a hotkey for Volume adjustment.  
3.  
4.  
MENU Button:  
Press this button to enter/select the icon (function) highlighted while the  
OSD is activated.  
Button:  
Press this button to increase the value of the function selected or move  
right/up to the previous function.  
This is also a hotkey for Brightness adjustment.  
Button:  
5.  
6.  
Use this hotkey to switch between the input sources (VGA and DVI).  
Power Button / Power Indicator:  
Press this button to turn the monitor on/off  
The color definition of the power indicator is as VW223B.  
1-6  
Chapter 1: Product introduction  
1.3.2  
Back view  
Stereo  
speaker  
Stereo  
speaker  
Screw holes for  
VESA Wall Mount  
USB hub  
Rear connectors  
1
2
3
4
5
Rear connectors  
1.  
2.  
3.  
AC-IN port. This port connects the power connector from the bundled power  
cord.  
Audio-in port (VW223S, VW223T only). This port connects PC audio  
source by the bundled audio cable.  
DVI port (VW223N, VW223T onlyl). This 24-pin port is for PC (Personal  
Computer) DVI-D digital signal connection.  
4.  
5.  
VGA port. This 15-pin port is for PC VGA connection.  
USB 2.0 port (VW223B only). This port is for the built-in USB hub and ASUS  
EzLink Display connection.  
ASUS VW223 Series LCD Monitor  
1-7  
 
1-8  
Chapter 1: Product introduction  
2.1  
Assembling the monitor base  
To assemble the monitor base:  
1.  
2.  
Have the front of the monitor face down on a table.  
Connect the base with the arm according to the below drawing. A click shows  
that the base has been connected successfully.  
We recommend that you cover the table surface with soft cloth to prevent  
damage to the monitor.  
2.2  
Adjusting the monitor  
For optimal viewing, we recommend that you look at the full face of the monitor,  
then adjust the monitor to the angle that is most comfortable for you.  
Hold the stand to prevent the monitor from falling when you change its angle.  
You can adjust the monitor’s angle from -5º to 25º.  
-5º~25º  
It is normal that the monitor slightly shakes while you adjust the the viewing  
angle.  
ASUS VW223 Series LCD Monitor  
2-1  
 
2.3  
Detaching the arm/base  
(for VESA wall mount)  
The detachable arm/base of the VW223 Series LCD monitor is specially designed  
for VESA wall mount.  
To detach the arm/base:  
1.  
2.  
3.  
Have the front of the monitor face down on a table.  
Remove the rubbers in the four screw holes (Figure 1).  
Use a screwdriver to remove the two screws on the arm (Figure 1), then slide  
out the arm/base to detach it from the monitor (Figure 2).  
Rubbers in the  
screw holes  
Two screws  
Arm/base  
Figure 1  
Figure 2  
We recommend that you cover the table surface with soft cloth to prevent  
damage to the monitor.  
2-2  
Chapter 2: Setup  
 
2.4  
Connecting the cables  
1.  
Connect the cables as the following instructions:  
AC-IN  
AUDIO DVI  
IN  
VGA  
2.0  
(B-Type)  
To connect the power cord: connect one end of the power cord securely to  
the monitor’s AC input port, and the other end to a power outlet.  
To connect the USB cable (VW223B only): connect the B-type end of the  
USB cable to the monitor's USB port, and the A-type end to the computer's  
USB 2.0 port.  
To connect the VGA cable / DVI cable (VW223N / VW223T only):  
a. Plug the VGA / DVI connector to the LCD monitor’s VGA / DVI port.  
b. Connect the other end of the VGA / DVI cable to your computer’s VGA /  
DVI port.  
c. Tighten the two screws to secure the VGA / DVI connector.  
To connect the audio cable (VW223S / VW223T only): connect one end  
of the audio cable to the monitor’s Audio-in port, and the other end to the  
computer's audio-out port.  
When both the VGA and the DVI cables are connected, you can choose either  
VGA mode or DVI mode from the Input Select item of the OSD functions.  
2.  
Gather all the cables with the cable hook.  
Cable hook  
2.5  
Turning on the monitor  
Gently press the power button  
button. The power indicator  
. See page 1-2 for the location of the power  
lights up in blue to show that the monitor is ON.  
ASUS VW223 Series LCD Monitor  
2-3  
 
2-4  
Chapter 2: Setup  
3.1  
OSD (On-Screen Display) menu  
3.1.1  
How to reconfigure  
1.  
2.  
Press the MENU button to activate the  
OSD menu.  
Press and  
to navigate through the  
functions. Highlight and activate the  
desired function by pressing the MENU  
button. If the function selected has a sub-  
menu, press and  
again to navigate  
through the sub-menu functions. Highlight  
and activate the desired sub-menu  
function by pressing the MENU button.  
3.  
4.  
Press and  
to change the settings of the selected function.  
To exit the OSD menu, press the  
adjust any other function.  
button. Repeat step 2 and step 3 to  
3.1.2  
OSD Function Introduction  
1.  
Spendid  
This function contains five sub-functions  
you can select for your preference. Each  
mode has the Reset selection, allowing  
you to maintain your setting or return to  
the preset mode.  
Scenery Mode: best choice  
for scenery photo display with  
SPLENDID™ Video Enhancement.  
Standard Mode: best choice for document editing with SPLENDID™  
Video Enhancement.  
Theater Mode: best choice for movie with SPLENDID™ Video  
Enhancement.  
Game Mode: best choice for game playing with SPLENDID™ Video  
Enhancement.  
Night View Mode: best choice for dark-scene game or movie with  
SPLENDID™ Video Enhancement.  
In the Standard Mode, the Satuation and Sharpness functions are not user-  
configurable.  
In the other modes, the sRGB function is not user-configurable.  
ASUS VW223 Series LCD Monitor  
3-1  
 
2.  
Image  
You can adjust brightness, contrast,  
sharpness, saturation, position (VGA only),  
ASCR, and focus (VGA only) from this  
main function.  
Brightness: the adjusting range  
is from 0 to 100. is a hotkey to  
activate this function.  
Contrast: the adjusting range is from  
0 to 100.  
is a hotkey to activate this function (for those models without  
speakers).  
ASCR: turns on/off the ASCR(ASUS Smart Contrast Ratio) function.  
Sharpness: the adjusting range is from 0 to 100.  
Saturation: the adjusting range is from 0 to 100.  
Position: adjusts the horizontal postition (H-Position) and the vertical  
position (V-Position) of the image. The adjusting range is from 0 to 100.  
Focus: reduces Horizonal-line noise and Vertical-line noise of the image  
by adjusting (Phase) and (Clock) separately. The adjusting range is from  
0 to 100.  
Phase adjusts the phase of the pixel clock signal. With a wrong phase  
adjustment, the screen shows horizontal disturbances.  
Clock (pixel frequency) controls the number of pixels scanned by one  
horizontal sweep. If the frequency is not correct, the screen shows vertical  
stripes and the image is not proportional.  
3.  
Color  
Select the image color you like from this  
function.  
Color Temp.: contains five color  
modes including Cool, Normal, Warm,  
sRGB, and User mode.  
Skin Tone: contains three color  
modes including Reddish, Natural,  
and Yellowish.  
In the User mode, colors of R (Red), G (Green), and B (Bluee) are user-  
configurable; the adjusting range is from 0-100.  
3-2  
Chapter 3: General Instruction  
4.  
Input Select  
In this function, you can select from VGA,  
DVI (Only for some models), or EzLink  
(VW223B only) input source.  
5.  
System Setup  
Allow you to adjust the system.  
Volume: the adjusting range is from  
0 to 100. is a hotkey to activate  
this function (for those models with  
speakers.).  
OSD Setup:  
*Adjusts the horizontal postition  
(H-Position)/ the vertical position (V-Position) of the OSD from 0 to 100.  
*Adjusts the OSD timeout from 10 to 120.  
*Enables or disables the DDC/CI function.  
Language: there are ten languages for your selection, including English,  
German, Italian, French, Dutch, Spanish, Russian, Traditional Chinese,  
Simplified Chinese, and Japanese.  
Aspect Control: adjusts the aspect ratio to “Full” or “4:3”.  
Information: shows the monitor information.  
Reset: Yes” allows you to restore the default setting.  
ASUS VW223 Series LCD Monitor  
3-3  
3.2  
ASUS EzLink Display (VW223B only)  
ASUS VW223B provides the easy-to-use EzLink Display that allows you to transfer  
digital video signal from your PC to your LCD via a standard USB 2.0 cable.  
Without the necessity of purchasing additional graphics cards, EzLink Display  
supports up to 6 ASUS LCD monitors connected to a single PC, providing the  
flexibility for multi-screen applications.  
3
4
6
2
1
5
The above illustration of multi-monitor connection is for reference only.  
Refer to previous chapters for actual connector locations.  
ASUS EzLink Display supports 32-bit Windows® OS environment only. No  
image will be displayed under computer POST, motherboard BIOS, or DOS  
environment.  
3.2.1  
System requirements  
Before you install the ASUS EzLink Display software, check if your system meets  
the following requirements:  
Hardware:  
PC with 1 GHz or higher  
256MB of RAM or higher  
USB 2.0 port  
30MB of available disk space  
Super VGA (800 x 600) video adaptor or higher resolution  
USB cable A-type to B-type  
Supporting operating system:  
Windows 2000 SP4  
Windows XP SP2/SP3  
Windows Vista  
3-4  
Chapter 3: General Instruction  
 
3.2.2  
Installing ASUS EzLink Display:  
1.  
2.  
Close all other applications.  
Insert the support CD into the  
optical drive and select the EzLink  
Driver.  
3.  
Select the language of the software  
end user licence agreement and  
click I Accept.  
4.  
The software installation starts.  
When finished, click Yes to restart  
the computer.  
ASUS VW223 Series LCD Monitor  
3-5  
 
3.2.3  
Using ASUS EzLink Display:  
Right-click the EzLink system tray icon to show the EzLink software menu.  
Check and configure software update  
options  
Fast-switch supported screen resolutions  
(Recommended: 1680x1050)  
Sets the color depth between 16 bit and  
32 bit (Recommended: 32 bit)  
Sets the direction of screen rotation  
Sets the location of the extended desktop  
Enables desktop extension  
Mirrors the content of the primary  
desktop to the extended desktop  
Turn off the mirror/extended display  
Launches the Windows® Display Settings  
tool  
3. ASUS EzLink Display (USB_XXXX-XXXXXXXXXXXX)  
3-6  
Chapter 3: General Instruction  
 
3.3  
Specifications summary  
Model Name  
Display  
VW223B VW223S VW223D VW223N VW223T  
Panel Size  
Panel Type  
22" Wide Screen  
TN  
Physical  
Resolution  
1680 x 1050  
300cd/ m2  
1000:1  
Brightness (Max.)  
Intrisinc Contrast  
Ratio (Max.)  
Dynamic  
Contrast Ratio  
(Max.)  
3000:1  
Viewing Angle  
(CR=10)  
160°(V) ; 170°(H)  
Color Saturation  
(NTSC)  
72%  
Display Colors  
Response Time  
HDCP support  
16.7 M (6-bit + Hi-FRC)  
5ms (Tr+Tf)  
Video  
Features  
No  
No  
No  
Yes  
Yes  
Yes  
Yes  
SPLENDID™  
Video Intelligence  
Tech.  
DCR Technology  
SPLENDID™  
Video Preset  
Mode  
5 modes (Standard, Scenery, Theater, Game, Night View)  
3 modes (Reddish, Normal, Yellowish)  
Skin-tone  
Selection  
Color  
Temperature  
Selection  
5 modes (9300K/ 7500K/ 6500K/ sRGB/ User Mode)  
Yes  
sRGB  
Audio  
Features  
Satellite Speaker  
1W x 2  
stereo  
1W x 2  
stereo  
No  
No  
No  
Convenient SPLENDID™  
Yes (5 modes)  
Yes (VGA mode)  
Yes  
Hotkeys  
Mode Select.  
Auto. Adjustment  
Brightness  
Adjustment  
Contrast  
Adjustment  
Yes  
No  
No  
Yes  
No  
Yes  
No  
No  
Volume  
Adjustment  
Yes  
Yes  
(continued on the next page)  
ASUS VW223 Series LCD Monitor  
3-7  
 
Specifications summary (continue)  
Model Name  
VW223B VW223S VW223D VW223N VW223T  
Input / Output PC Digital Input  
USB 2.0  
No  
No  
DVI  
DVI  
PC Analogue  
Input  
D-Sub  
PC Audio Input  
(to built-in  
speakers)  
3.5mm  
Mini-jack  
3.5mm  
Mini-jack  
No  
No  
No  
Microphone Input  
Earphone Output  
No  
No  
Power  
Power ON  
65 W  
55W  
55W  
55W  
55W  
Consumption  
Power Saving  
Mode  
< 2W  
Power OFF Mode  
Detachable Base  
Tilt  
< 1W  
Yes  
Mechanical  
Design  
+25° to -5°  
No  
Swivel  
Pivot  
No  
Height  
Adjustment  
No  
VESA Wall  
Mounting  
Yes (100mm x 100mm)  
511.56(W) x 402.95(H) x 210(D) mm  
570(W) x 460(H) x 152(D) mm  
Dimension  
Weight  
Phys. Dimension  
(WxHxD)  
Box Dimension  
(WxHxD)  
Net Weight (Esti.) 4924 g  
4850 g  
6072 g  
4850 g  
6052 g  
4850 g  
6258 g  
4850 g  
6290 g  
Gross Weight  
6220 g  
(Esti.)  
Multi-  
languages  
OSD  
10 Languages (English, German, Italian, French, Dutch,  
Spanish, Russian, Traditional Chinese, Simplified  
Chinese, Japanese)  
User Guide /  
28 Languages QSG (English, German, Italian, French,  
Quick Start Guide Dutch, Spanish, Russian, Portuguese, Polish, Czech,  
Swedish, Norwegian, Finnish, Danish, Hungarian,  
Serbian, Greek, Romanian, Traditional Chinese,  
Simplified Chinese, Japanese, Turkish, Arabic, Korean,  
Thai, Indonesian, Bulgarian, Slovak)  
Accessories  
Power cord, VGA cable, USB cable (B only), Audio cable  
(S, T only), DVI cable (T, N only) Warranty card, QSG,  
CD  
Regulation Approvals  
Energy Star®, UL/cUL, CB, CE, FCC, CCC, BSMI,  
Gost-R, C-Tick, VCCI, PSB, J-MOSS, RoHS, WEEE,  
Windows Vista WHQL  
*Specifications are subject to change without notice.  
3-8  
Chapter 3: General Instruction  
3.4  
Troubleshooting (FAQ)  
Problem  
Possible Solution  
Power LED is not ON  
• Press the  
button to check if the monitor  
is in the ON mode.  
• Check if the power cord is properly  
connected to the monitor and the power  
outlet.  
The power LED lights amber and there is no • Check if the monitor and the computer are  
screen image  
in the ON mode.  
• Make sure the signal cable is properly  
connected the monitor and the computer.  
• Inspect the signal cable and make sure  
none of the pins are bent.  
• Connect the computer with another  
available monitor to check if the computer  
is properly working.  
Screen image is too light or dark  
• Adjust the Contrast and Brightness settings  
via OSD.  
Screen image is not centered or sized  
• Press the  
button for two seconds to  
properly  
automatically adjust the image.  
• Adjust the H-Position or V-Position settings  
via OSD.  
Screen image bounces or a wave pattern is • Make sure the signal cable is properly  
present in the image  
connected to the monitor and the computer.  
• Move electrical devices that may cause  
electrical interference.  
Screen image has color defects (white does • Inspect the signal cable and make sure that  
not look white)  
none of the pins are bent.  
• Perform Reset via OSD.  
• Adjust the R/G/B color settings or select the  
Color Temperature via OSD.  
Screen image is blurry or fuzzy  
• Press the  
button for two seconds to  
automatically adjust the image (for VGA  
mode only).  
• Adjust the Phase and Clock settings via  
OSD.  
No sound or sound is low  
• Ensure that the audio cable is properly  
connected to the monitor and the computer  
• Adjust the volume settings of both your  
monitor and computer.  
• Ensure that the computer sound card driver  
is properly installed and activated.  
ASUS VW223 Series LCD Monitor  
3-9  
 
3.5  
Supported operating modes  
Horizontal  
Resolution  
Refresh Rate  
Standard Type  
Frequency  
31.5 kHz  
31.5 kHz  
35.0 kHz  
37.9 kHz  
37.5 kHz  
37.9 kHz  
48.1 kHz  
46.9 kHz  
49.7 kHz  
48.4 kHz  
56.5 kHz  
60.0 kHz  
67.5 kHz  
60.0 kHz  
64.0 kHz  
80.0 kHz  
59.9 kHz  
75.0 kHz  
65.3 kHz  
720 x 400  
640 x 480  
640 x 480  
640 x 480  
640 x 480  
800 x 600  
800 x 600  
800 x 600  
832 x 624  
70 Hz  
60 Hz  
67 Hz  
72 Hz  
75 Hz  
60 Hz  
72 Hz  
75 Hz  
75 Hz  
60 Hz  
70 Hz  
75 Hz  
75 Hz  
60 Hz  
60 Hz  
75 Hz  
60 Hz  
60 Hz  
60 Hz  
DOS  
Industry Standard  
MAC  
VESA Standard  
VESA Standard  
VESA Guidelines  
VESA Standard  
VESA Standard  
MAC  
1024 x 768  
1024 x 768  
1024 x 768  
1152 x 864  
1280 x 960  
1280 x 1024  
1280 x 1024  
1440 x 900  
1600 x 1200  
1680 x 1050  
VESA Guidelines  
VESA Standard  
VESA Standard  
VESA Standard  
VESA Standard  
VESA Standard  
VESA Standard  
CVT  
VESA Standard  
CVT  
* Modes not listed in the table may not be supported. For optimal resolution, we recommend that  
you choose a mode listed in the table above.  
3-10  
Chapter 3: General Instruction  
 

GE ZEU36K User Manual
GE PP972 User Manual
Geemarc Clear Sound Dect 300 User Manual
Franke Consumer Products Cooktop PRI 5 User Manual
Electrolux 260708 User Manual
Dell ST2010B User Manual
Dell E170S User Manual
DCS CS 364GD User Manual
Dacor ETT304 User Manual
AG Neovo Neovo F 17 User Manual