Asus Computer Monitor VK191 User Manual

VK191 Series  
LCD Monitor  
User Guide  
 
Contents  
Chapter 1:  
Product introduction  
Chapter 2:  
Setup  
Chapter 3:  
General instruction  
iii  
 
Notices  
Federal Communications Commission Statement  
This device complies with Part 15 of the FCC Rules. Operation is subject to the  
following two conditions:  
This device may not cause harmful interference, and  
This device must accept any interference received including interference that  
may cause undesired operation.  
This equipment has been tested and found to comply with the limits for a  
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against harmful interference in a  
residential installation. This equipment generates, uses and can radiate radio  
frequency energy and, if not installed and used in accordance with manufacturer’s  
instructions, may cause harmful interference to radio communications. However,  
there is no guarantee that interference will not occur in a particular installation. If  
this equipment does cause harmful interference to radio or television reception,  
which can be determined by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one or more of the following  
measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment to an outlet on a circuit different from that to which the  
receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
The use of shielded cables for connection of the monitor to the graphics card is  
required to assure compliance with FCC regulations. Changes or modifications  
to this unit not expressly approved by the party responsible for compliance  
could void the user’s authority to operate this equipment.  
As an Energy Star® Partner, our company has determined that this product meets  
the Energy Star® guidelines for energy efficiency.  
Canadian Department of Communications Statement  
This digital apparatus does not exceed the Class B limits for radio noise emissions  
from digital apparatus set out in the Radio Interference Regulations of the  
Canadian Department of Communications.  
This class B digital apparatus complies with Canadian ICES-003.  
iv  
 
Safety information  
Before setting up the monitor, carefully read all the documentation that came  
with the package.  
To prevent fire or shock hazard, never expose the monitor to rain or moisture.  
Never try to open the monitor cabinet. The dangerous high voltages inside the  
monitor may result in serious physical injury.  
If the power supply is broken, do not try to fix it by yourself. Contact a qualified  
service technician or your retailer.  
Before using the product, make sure all cables are correctly connected and the  
power cables are not damaged. If you detect any damage, contact your dealer  
immediately.  
Slots and openings on the back or top of the cabinet are provided for  
ventilation. Do not block these slots. Never place this product near or over a  
radiator or heat source unless proper ventilation is provided.  
The monitor should be operated only from the type of power source indicated  
on the label. If you are not sure of the type of power supply to your home,  
consult your dealer or local power company.  
Use the appropriate power plug which complies with your local power  
standard.  
Do not overload power strips and extention cords. Overloading can result in  
fire or electric shock.  
Avoid dust, humidity, and temperature extremes. Do not place the monitor in  
any area where it may become wet. Place the monitor on a stable surface.  
Unplug the unit during a lightning storm or if it will not be used for a long period  
of time. This will protect the monitor from damage due to power surges.  
Never push objects or spill liquid of any kind into the slots on the monitor  
cabinet.  
To ensure satisfactory operation, use the monitor only with UL listed  
computers which have appropriate configured receptacles marked between  
100-240V AC.  
If you encounter technical problems with the monitor, contact a qualified  
service technician or your retailer.  
This symbol of the crossed out wheeled bin indicates that the product (electrical,  
electronic equipment, and mercury-containing button cell battery) should not  
be placed in municipal waste. Please check local regulations for disposal of  
electronic products.  
v
 
Care & Cleaning  
Before you lift or reposition your monitor, it is better to disconnect the cables  
and power cord. Follow the correct lifting techniques when positioning the  
monitor. When lifting or carrying the monitor, grasp the edges of the monitor.  
Do not lift the display by the stand or the cord.  
Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor  
surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed  
with a cloth dampened with mild cleaner.  
Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended  
for use with the LCD. Never spray cleaner directly on the screen, as it may drip  
inside the monitor and cause an electric shock.  
The following symptoms are normal with the monitor:  
The screen may flicker during the initial use due to the nature of the fluorescent  
light. Turn off the Power Switch and turn it on again to make sure that the  
flicker disappears.  
You may find slightly uneven brightness on the screen depending on the  
desktop pattern you use.  
When the same image is displayed for hours, an afterimage of the previous  
screen may remain after switching the image. The screen will recover slowly or  
you can turn off the Power Switch for hours.  
When the screen becomes black or flashes, or cannot work anymore, contact  
your dealer or service center to fix it. Do not repair the screen by yourself!  
Conventions used in this guide  
WARNING: Information to prevent injury to yourself when trying to  
complete a task.  
CAUTION: Information to prevent damage to the components when trying  
to complete a task.  
IMPORTANT: Information that you MUST follow to complete a task.  
NOTE: Tips and additional information to aid in completing a task.  
vi  
 
Where to find more information  
Refer to the following sources for additional information and for product and  
software updates.  
1.  
2.  
ASUS websites  
The ASUS websites worldwide provide updated information on ASUS  
Optional documentation  
Your product package may include optional documentation that may have  
been added by your dealer. These documents are not part of the standard  
package.  
vii  
viii  
1.1  
Welcome!  
Thank you for purchasing the ASUS® VK191 Series LCD monitor!  
The latest widescreen LCD monitor from ASUS provides a crisper, broader, and  
brighter display, plus a host of features that enhance your viewing experience.  
Besides, the built-in 1.3 mega-pixel webcam enhances image quality. No need  
for installing additional communication tools while having a video conference with  
friends online!  
With these features, you can enjoy the convenience and delightful audio-visual  
experience that the VK191 Series brings you!  
1.2  
Package contents  
Check your VK191 Series LCD monitor package for the following items:  
LCD monitor  
Support CD  
Quick start guide  
Power cord x1  
VGA cable x1  
DVI cable x1 (For some models)  
USB cable x1  
Audio cable x1 (For some models)  
If any of the above items is damaged or missing, contact your retailer  
immediately.  
ASUS VK191 Series LCD Monitor  
1-1  
1.3  
Monitor introduction  
1.3.1  
Front view  
Webcam  
Base  
1
2
3
4
5
1.  
Button:  
Use this hotkey to switch from five video preset modes (Game  
Mode, Night View Mode, Scenery Mode, Standard Mode, Theater Mode)  
with SPLENDID™ Video Enhancement Technology.  
Exit the OSD menu or go back to the previous menu as the OSD menu  
is active.  
Automatically adjust the image to its optimized position, clock, and phase  
by pressing this button for 2-4 seconds (for VGA mode only).  
2.  
Button (For those models with speakers):  
Press this button to decrease the value of the function selected or move  
left/down to the next function.  
This is also a hotkey for Volume adjustment.  
Button (For those models without speakers):  
Press this button to decrease the value of the function selected or move  
left/down to the previous function.  
This is also a hotkey for Contrast adjustment.  
3.  
4.  
MENU Button:  
Press this button to enter/select the icon (function) highlighted while the  
OSD is activated.  
Button:  
Press this button to increase the value of the function selected or move  
right/up to the previous function.  
This is also a hotkey for Brightness adjustment.  
1-2  
Chapter 1: Product introduction  
5.  
Power button/power indicator  
Press this button to turn the monitor on/off  
The color definition of the power indicator is as the below table.  
Status  
Blue  
Description  
ON  
Amber  
OFF  
Standby mode  
OFF  
1.3.2  
Back view  
Stereo speaker  
Stereo speaker  
(For some models)  
(For some models)  
Screw holes for  
VESA Wall Mount  
Rear connectors  
1
2
3
4
5
Rear connectors  
1.  
AC-IN port. This port connects the power connector from the bundled power  
cord.  
2.  
3.  
USB 2.0 port. This port is for the built-in webcam connection.  
DVI port (For some models). This 24-pin port is for PC (Personal Computer)  
DVI-D digital signal connection.  
4.  
5.  
VGA port. This 15-pin port is for PC VGA connection.  
Audio-in port (For those models with speakers). This port connects PC  
audio source by the bundled audio cable.  
The VESA wall mount kit (100 mm x 100 mm) is purchased separately.  
ASUS VK191 Series LCD Monitor  
1-3  
1-4  
Chapter 1: Product introduction  
2.1  
Assembling the monitor base  
To assemble the monitor base:  
1.  
2.  
Have the front of the monitor face down on a table.  
Connect the base with the arm according to the below drawing. A click shows  
that the base has been connected successfully.  
We recommend that you cover the table surface with soft cloth to prevent  
damage to the monitor.  
2.2  
Adjusting the monitor  
For optimal viewing, we recommend that you look at the full face of the  
monitor, then adjust the monitor to the angle that is most comfortable for you.  
Hold the stand to prevent the monitor from falling when you change its angle.  
You can adjust the monitor’s angle from -5˚ to 20˚.  
-5˚�20˚  
It is normal that the monitor slightly shakes while you adjust the the viewing  
angle.  
ASUS VK191 Series LCD Monitor  
2-1  
2.3  
Detaching the arm/base  
(for VESA wall mount)  
The detachable arm/base of the VK191 Series LCD monitor is specially designed  
for VESA wall mount.  
To detach the arm/base:  
1.  
2.  
3.  
Have the front of the monitor face down on a table.  
Remove the rubbers in the four screw holes (Figure 1).  
Follow the direction to remove the back lid (Figure 1). Use a screwdriver to  
remove the four screws on the arm, then slide out the arm/base to detach it  
from the monitor (Figure 2).  
Rubbers in the  
screw holes  
Back lid  
Arm/base  
Figure 1  
Figure 2  
We recommend that you cover the table surface with soft cloth to prevent  
damage to the monitor.  
2-2  
Chapter 2: Setup  
2.4  
Connecting the cables  
1.  
Connect the cables as the following instructions:  
USB  
VGA  
To connect the power cord: connect one end of the power cord securely to  
the monitor’s AC input port, and the other end to a power outlet.  
To connect the USB cable: connect one end of the USB cable (upstream) to  
the monitor's USB port, and the other end to the computer's USB 2.0 port.  
To connect the VGA/DVI cable:  
a. Plug the VGA/DVI connector to the LCD monitor’s VGA/DVI port.  
b. Connect the other end of the VGA/ DVI cable to your computer’s VGA/  
DVI port.  
c. Tighten the two screws to secure the VGA/DVI connector.  
To connect the audio cable (For those models with speakers): connect one  
end of the audio cable to the monitor’s Audio-in port, and the other end to the  
computer's audio-out port.  
When both the VGA and the DVI cables are connected, you can choose either  
VGA mode or DVI mode from the Input Select item of the OSD functions.  
2.  
Gather all the cables with the cable hook.  
Cable hook  
2.5  
Turning on the monitor  
Gently press the power button  
button. The power indicator  
. See page 1-2 for the location of the power  
lights up in blue to show that the monitor is ON.  
ASUS VK191 Series LCD Monitor  
2-3  
2.6  
LifeFrame 2 software  
ASUS VK191 provides the easy-to-use LifeFrame 2 software that can work with  
the webcam, allowing users to create their own photos or video clips.  
LifeFrame 2 only supports Microsoft® Windows® Vista / XP Service Pack 2  
operating systems.  
The LifeFrame 2 software is bundled in the support CD.  
Installation instructions  
1.  
2.  
3.  
Close all other applications.  
Insert the support CD into the optical drive and run the LifeFrame 2 program.  
Follow the on-screen instructions to complete the installation  
2-4  
Chapter 2: Setup  
3.1  
OSD (On-Screen Display) menu  
3.1.1  
How to reconfigure  
1.  
2.  
Press the MENU button to activate  
the OSD menu.  
Press and  
to navigate through the  
functions. Highlight and activate the  
desired function by pressing the MENU  
button. If the function selected has a sub-  
menu, press and  
again to navigate  
through the sub-menu functions. Highlight and activate the desired sub-menu  
function by pressing the MENU button.  
3.  
4.  
Press and  
to change the settings of the selected function.  
To exit the OSD menu, press the  
adjust any other function.  
button. Repeat step 2 and step 3 to  
3.1.2  
OSD Function Introduction  
1.  
Spendid  
This function contains five sub-functions  
you can select for your preference. Each  
mode has the Reset selection, allowing  
you to maintain your setting or return to  
the preset mode.  
Scenery Mode: best choice  
for scenery photo display with  
SPLENDID™ Video Intelligence  
Technology.  
Standard Mode: best choice for document editing with SPLENDID™  
Video Intelligence Technology.  
Theater Mode: best choice for movie with SPLENDID™ Video  
Intelligence Technology.  
Game Mode: best choice for game playing with SPLENDID™ Video  
Intelligence Technology.  
Night View Mode: best choice for dark-scene game or movie with  
SPLENDID™ Video Intelligence Technology.  
In the Standard Mode, the Saturation and Sharpness functions are not  
user-configurable.  
In the other modes, the sRGB function is not user-configurable.  
ASUS VK191 Series LCD Monitor  
3-1  
2.  
Image  
You can adjust brightness, contrast,  
sharpness, saturation, position (VGA only),  
ASCR, and focus (VGA only) from this main  
function.  
Brightness: the adjusting range is from  
0 to 100.  
function.  
is a hotkey to activate this  
Contrast: the adjusting range is from 0 to 100.  
is a hotkey to activate  
this function (For those models without speakers).  
ASCR: turns on/off the ASCR(ASUS Smart Contrast Ratio) function.  
Sharpness: the adjusting range is from 0 to 100.  
Saturation: the adjusting range is from 0 to 100.  
Position: adjusts the horizontal postition (H-Position) and the vertical  
position (V-Position) of the image. The adjusting range is from 0 to 100.  
Focus: reduces Horizonal-line noise and Vertical-line noise of the image  
by adjusting (Phase) and (Clock) separately. The adjusting range is from  
0 to 100.  
Phase adjusts the phase of the pixel clock signal. With a wrong phase  
adjustment, the screen shows horizontal disturbances.  
Clock (pixel frequency) controls the number of pixels scanned by one  
horizontal sweep. If the frequency is not correct, the screen shows vertical  
stripes and the image is not proportional.  
3.  
Color  
Select the image color you like from this  
function.  
Color Temp.: contains five color  
modes including Cool, Normal, Warm,  
sRGB, and User mode.  
Skin Tone: contains three color  
modes including Reddish, Natural, and  
Yellowish.  
In the User mode, colors of R (Red), G (Green), and B (Bluee) are user-  
configurable; the adjusting range is from 0-100.  
3-2  
Chapter 3: General Instruction  
4.  
Input Select  
In this function, you can select either VGA  
or DVI input source.  
5.  
System Setup  
Allow you to adjust the system.  
Volume: the adjusting range is from  
0 to 100. is a hotkey to activate  
this function (For those models with  
speakers.).  
OSD Setup:  
*Adjusts the horizontal postition (H-Position)/ the vertical position  
(V-Position) of the OSD from 0 to 100.  
*Adjusts the OSD timeout from 10 to 120.  
*Enables or disables the DDC/CI function.  
Language: there are ten languages for your selection, including English,  
German, Italian, French, Dutch, Spanish, Russian, Traditional Chinese,  
Simplified Chinese, and Japanese.  
Aspect Control: adjusts the aspect ratio to “Full” or “4:3”.  
Information: shows the monitor information.  
Reset: “Yes” allows you to restore the default setting.  
ASUS VK191 Series LCD Monitor  
3-3  
3.2  
Specifications summary  
Panel Type  
Panel size  
TFT LCD  
19" wide screen  
Max. Resolution  
Brightness  
WXGA+ 1440 x 900  
300cd/m2  
Contrast Ratio (Typ.) / (Max.) 1000:1 / 3000:1 (with ASCR ON)  
Viewing angle(H/V) CR>10  
Display colors  
160˚/160˚  
16.7M  
Response time  
Webcam  
5ms  
1.3 Mega pixel / VGA (VK191D only)  
Yes  
SPLENDID™ Video  
Intelligence Technology  
SPLENDID™ selection  
Auto adjustment  
5 video preset modes (by hotkey)  
Yes (by hotkey)  
Color temperature selection 5 color temperatures  
Skin-Tone selection  
Digital input  
Analog input  
Audio-in port  
Color  
3 skin-tones  
DVI-D with HDCP (VK191T / VK191N)  
D-Sub  
3.5 mm Mini-jack (VK191T / VK191S)  
Black  
Speaker (Built-in)  
Power LED  
1W x 2 Stereo, RMS (VK191T / VK191S)  
Blue (On)/ Amber (Standby)  
100 x 100mm (purchased separately)  
-5˚�+20˚  
VESA wall mount  
Tilt  
Kensington lock  
Voltage rating  
Yes  
AC: 100�240V  
*Specifications are subject to change without notice.  
3-4  
Chapter 3: General Instruction  
3.3  
Troubleshooting (FAQ)  
Problem  
Power LED is not ON  
Possible Solution  
• Press the  
button to check if the monitor is in  
the ON mode.  
• Check if the power cord is properly connected to  
the monitor and the power outlet.  
The power LED lights amber and there is no  
screen image  
• Check if the monitor and the computer are in the  
ON mode.  
• Make sure the signal cable is properly connected  
the monitor and the computer.  
• Inspect the signal cable and make sure none of  
the pins are bent.  
• Connect the computer with another available  
monitor to check if the computer is  
properly working.  
Screen image is too light or dark  
• Adjust the Contrast and Brightness settings via  
OSD.  
Screen image is not centered or sized properly  
• Press the  
button for 2–3 seconds to  
automatically adjust the image (VGA input only).  
• Adjust the H-Position or V-Position settings via  
OSD (VGA input only).  
Screen image bounces or a wave pattern is  
present in the image  
• Make sure the signal cable is properly  
connected to the monitor and the computer.  
• Move away electrical devices that may cause  
electrical interference.  
Screen image has color defects (white does not • Inspect the signal cable and make sure that  
look white)  
none of the pins are bent.  
• Perform All Reset via OSD.  
• Adjust the R/G/B color settings or select the  
Color Temperature via OSD.  
Screen image is blurry or fuzzy  
No sound or sound is low  
• Press the  
button for 2–3 seconds to  
automatically adjust the image (VGA input only).  
• Adjust the Phase and Clock settings via OSD  
(VGA input only).  
• Ensure that thse audio cable is properly  
connected to the monitor and the computer  
• Adjust the volume settings of both your  
monitor and computer.  
• Ensure that the computer sound card driver  
is properly installed and activated.  
Webcam is not working  
• Make sure that you have connected the USB cable  
securely to both the LCD monitor and your  
computer.  
• Make sure that you use the Microsoft® Windows®  
Vista / XP Service Pack 2 operating systems.  
ASUS VK191 Series LCD Monitor  
3-5  
3.4  
Supported operating modes  
Resolution  
Refresh Rate  
60 Hz  
72 Hz  
75 Hz  
56 Hz  
60 Hz  
75 Hz  
60 Hz  
70 Hz  
75 Hz  
60 Hz  
60 Hz  
60 Hz  
75 Hz  
60 Hz  
60 Hz  
60 Hz  
60 Hz  
60 Hz  
60 Hz  
Horizontal Frequency  
640 x 480  
640 x 480  
640 x 480  
800 x 600  
800 x 600  
800 x 600  
1024 x 768  
1024 x 768  
1152 x 864  
1280 x 720  
1280 x 768  
1280 x 768  
1280 x 768  
1280 x 800  
1280 x 960  
1280 x 1024  
1360 x 768  
1440 x 900  
1440 x 900  
31.5 kHz  
37.9 kHz  
37.5 kHz  
35.1 kHz  
37.9 kHz  
46.9 kHz  
48.4 kHz  
56.5 kHz  
60.0 kHz  
44.7 kHz  
47.4 kHz  
47.8 kHz  
60.3 kHz  
49.6 kHz  
60.0 kHz  
64.0 kHz  
47.7 kHz  
55.5 kHz  
59.9 kHz  
* Modes not listed in the table may not be supported. For optimal resolution, we recommend that  
you choose a mode listed in the table above.  
3-6  
Chapter 3: General Instruction  

HP Hewlett Packard Hewlett Packard Computer Monitor 9500 User Manual
Grundig Computer Hardware HMS470 User Manual
Frigidaire FGIC3667MB User Manual
Frigidaire FGEC3065K User Manual
Electrolux EHE 688W User Manual
Eizo EIZO FlexScan SX2761W BK User Manual
Cypress FLEx36 CYD09S36V User Manual
Audiovox ADV200S User Manual
AT T TL96371 User Manual
AOpen AK77 600N User Manual