|
Setting Up Your
Studio Display
15-inch flat panel monitor
1
4
5
Protecting Your Display From Theft 30
Conserving Energy 31
Appendix
Technical Information 33
Communications Regulation Information 37
3
Flip-out stand
Power cord
Manual and service
and support materials
Software
Power adapter
C H A P T E R
1
1
About Your Apple Studio Display
Important Safety Instructions
m Turn off the computer before setting up your Apple Studio Display. Leave the computer
plugged into a grounded outlet.
Important The only way to disconnect the monitor’s power completely is to unplug the
power cord from the computer or electrical outlet. Make sure at least one end of the
power cord is within easy reach so that you can unplug the display if you need to.
m Don’t press or put hard objects against the screen.
m Read all the setup instructions carefully before you plug your display into a power source.
Warning Use only the power adapter that came with your display. Adapters for other
computer equipment may look similar, but they may damage your display.
This equipment is intended to be electrically grounded. This is a safety feature. Your
power cord has a plug that has a third grounding pin. Be sure to connect it only to a
grounded outlet. If you are unable to insert the plug into the outlet, contact a licensed
purpose of the grounding plug!
If your power cord connects directly to the power socket on your computer, be sure that
the computer is grounded.
For additional safety information, see Chapter 5, “Safety, Health, and Maintenance.”
Choosing a Good Location for Your Display
When determining where to place your display, keep the following points in mind:
m Make sure the power adapter cable, power cord, and display cables easily reach from the
back of the display to your computer and an electrical outlet or power strip.
m All cables should be unobstructed when you adjust the display. If you don’t allow enough
clearance, the connectors might be damaged when the cables hit an obstruction.
5
Step 2: Plug in the display’s power adapter.
Plug the power adapter cord
into a grounded wall outlet
or power strip. (Some cords may
connect to the power socket in
the back of your computer.)
Plug the display’s
power cable into
the power adapter.
About Your Apple Studio Display
7
Step 3: Plug In the display’s DVI and USB connectors.
Plug the USB connector
into the computer here.
Plug the DVI connector
into the computer here.
Although your graphics card may have two monitor ports, connect your Apple Studio Display
to the Digital Visual Interface (DVI) port only.
Important You can use only one monitor connected to your graphics card at a time.
8
Chapter 1
Step 4: Connect a USB keyboard to the display, if desired.
Connect your
USB keyboard here.
1
2
About Your Apple Studio Display
9
Step 5: Press the monitor power button.
Both your computer and your monitor start up. After a few moments, the Macintosh desktop
appears on the screen.
If nothing appears or you see other problems, see Chapter 3, “Troubleshooting,” for more
information.
How Do I Turn Off the Display?
Your monitor power button shuts down or puts to sleep both your monitor and computer at
the same time. Press the monitor power button again to start up or wake the monitor and
computer.
You can change the power button setting so that pressing the monitor power button affects
the monitor only. To change the power button setting, you use the Preferences section of the
Monitors control panel. For more information about sleep settings and the Energy Saver or
Monitors control panel, see Mac Help.
What’s Next
Congratulations—you’ve finished setting up your display. Next, you need to install the
software that came with your display.
10
Chapter 1
Power
indicator light
®
¤
® Power button
Brightness
controls
¤
Keyboard storage pads
Carrying handle
USB port cover
Desktop stand
Power adapter
Security ring
DVI connector
USB connector
About Your Apple Studio Display 11
Finding Answers
When you have questions about your display, there are several places to look for answers.
In this manual
Use this manual to find out how to set up your display, install the
software, and find solutions to common problems.
In Mac Help
If you need help using the Apple Displays Software or adjusting
the display, open the Help menu and choose Mac Help. Type the
topic you want information about and click Search, or use the
table of contents to find your topic.
On the Internet
Apple maintains a number of sites on the World Wide Web that
provide product information, software updates, and technical
support information. You can view Apple’s home page at
Over the telephone
If you can’t find answers in any of the materials provided, call the
Apple Assistance Center. (See the service and support
information that came with this display.)
12
Chapter 1
C H A P T E R
2
2
Installing the Apple Displays Software
To install the Apple Displays Software, follow these steps:
Insert the Apple Displays Software CD into your computer’s CD-ROM drive.
The CD icon appears on the desktop.
1
Important Make sure that you install the software from the Apple Displays Software CD
that came with your monitor.
2
Double-click the CD icon.
The Apple Displays Software window opens.
3
4
5
6
Double-click the folder that contains the language you want to use.
Double-click the Apple Displays Software folder.
Double-click the Upgrader icon to start the installation program.
Follow the instructions on the screen until the installation is complete.
Note: During installation, you are presented with the terms of your software license
agreement. Please read the terms carefully before you agree.
The program checks to make sure you have the system software you need to use the display.
If anything is missing, a message tells you what you need. You won’t be able to install the
software until you correct the problem.
After the installation, you need to restart your computer.
Click Restart.
7
The software is now installed and the display is ready for use.
13
About Your Apple Displays Software
The Apple Displays Software is a set of files that let you adjust basic picture and color
settings.
m The Monitors control panel lets you change the way your computer displays images. The
Monitors control panel is located in the Control Panels folder in the Apple (K) menu. For
help using the Monitors control panel, open the Help menu and choose Show Balloons.
For more information, see Mac Help.
m The Sound control panel lets you change the way your computer processes sound. You
can use it to set speaker volume, select input and output devices such as microphones
and speakers, and choose other settings such as alert sounds. The Sound control panel is
located in the Control Panels folder in the Apple (K) menu. For more information, see
Mac Help.
m The Control Strip lets you quickly adjust screen resolution and color depth. For help
using the Control Strip, see Mac Help.
m DigitalColor Meter, located in the Apple (K) menu, lets you obtain the RGB (red, green,
and blue) values your computer uses to create colors and specify these values using other
color systems. For help using DigitalColor Meter, click the Help button in the upper-right
corner of the DigitalColor Meter window.
®
m The PANTONE Color Picker for Apple lets you specify PANTONE values for colors used in
your documents in many application programs. In these applications, the system color
picker opens automatically when a new color needs to be specified. For more information
about using the PANTONEColor Picker for Apple, see Mac Help.
m ColorSync is Apple’s unique color-matching software that ensures the colors you input
(using a scanner or camera) closely match the colors you see on your screen and on the
printed page. For help using ColorSync, see Mac Help.
Adjusting the Display
You can adjust the monitor’s brightness by pressing the brightness buttons on the display.
You can calibrate the display and adjust additional settings using the Monitors control panel.
For more information about the Monitors control panel, choose Mac Help from the Help
menu.
14
Chapter 2
C H A P T E R
3
3
Troubleshooting
Check this section for solutions to problems you might experience with your display.
Warning If you have a problem with your display and nothing presented in this manual
solves it, consult the service and support information that came with your display for
instructions on how to contact an Apple-authorized service provider or Apple for
assistance. If you attempt to repair the display yourself, any damage you may cause to the
display will not be covered by the limited warranty on your display. Contact an Apple-
authorized dealer or service provider for additional information about this or any other
warranty question.
The light on the front of the monitor is flashing amber.
The power light flashes amber when an error has been detected.
m If you see a repeating sequence of three short flashes, the monitor is detecting input in
the wrong video format. Check that you have the correct graphics card installed and that
you’ve installed the correct monitor software.
m If you see a sequence of two short flashes and a long flash, the monitor is detecting a
problem with a backlighting lamp. Contact an Apple-authorized dealer or service provider
for information about resolving the problem.
No image appears on the screen.
m Make sure the display is turned on.
m Make sure the computer is turned on.
m Make sure the power cord is plugged in properly.
If the display power cord is plugged into a grounded wall outlet or power strip, check to
see whether power to the outlet has been interrupted. You can test the outlet by plugging
in something that you know works—like a desk lamp or radio.
m Make sure the DVI and USB display cables are connected to your computer properly.
m Make sure your computer is not in sleep.
15
m Make sure the brightness is set properly. The brightness control (marked by ¤) is under
the right front edge of the display.
During installation of the Apple Displays Software, a message appears, “This
version of system software is not supported by the Apple Displays Software.”
m Make sure you’re using the latest version of the Mac OS.
startup hard disk in the Installation dialog box.
A message appears, “This monitor is not supported by this version of the Apple
Displays Software.”
m Make sure you have installed the Apple Displays Software that came with your display. For
installation instructions, see Chapter 2, “Installing the Apple Displays Software.”
The screen image appears dim or flickers.
m Adjust the brightness setting. The brightness control (marked by ¤) is under the right
front edge of the display.
m Calibrate the monitor using the Calibrate option of the Monitors control panel.
m The flickering could be caused by interference from a nearby power line, a fluorescent
light, or an electrical device—for example, a radio, a microwave oven, or another
computer. Try relocating nearby electrical devices, or moving your computer and display.
The screen image is blurry.
m Switch the resolution of the display using the Monitors control panel or the Control Strip.
It’s recommended that you choose the 1024 x 768 resolution for best results.
No colors appear on the screen or the colors don’t look right.
m Make sure the display cables are connected firmly to the correct ports on the computer.
m You may want to calibrate your monitor using the Monitors control panel. For more
information on color and your display, see Mac Help.
m Open the Monitors control panel and check if your monitor is set to display shades of
gray. For more information on color and your display, see Mac Help.
After you change the screen resolution, desktop icons move.
m Changing the screen resolution affects the display of information on your screen. The
operating system may automatically reposition icons after you change the screen
resolution.
The screen freezes.
m If you are using both Energy Saver and a screen-saver program, the screen-saver program
may be conflicting with Energy Saver. Turn off either the screen-saver program or Energy
Saver, and restart your computer.
16
Chapter 3
The name of your display doesn’t appear in the title bar of the Monitors control
panel.
m Make sure you’ve installed the Apple Displays Software that came with your display. For
installation instructions, see Chapter 2, “Installing the Apple Displays Software.”
Changes in the Monitors control panel don’t appear on the display.
m Each display connected to your computer has its own Monitors control panel. Use the
control panel with the name of your display in the window’s title bar.
m Make sure you have installed the Apple Displays Software that came with your display. For
installation instructions, see Chapter 2, “Installing the Apple Displays Software.”
You don’t see an onscreen display when you press the brightness button, or
you don’t see power mode options in the Monitors control panel.
m Make sure you’ve connected the USB connector on the display cable to the USB port on
your computer. Some of the features of the Apple Displays Software require a USB
m If the Apple Displays Software is installed and you start up your computer holding the
Shift key down to disable extensions, the software will not run. Restart your computer
without disabling extensions to use the software.
m Reinstall the software that came with your display. For installation instructions, see
Chapter 2, “Installing the Apple Displays Software.”
When you press the monitor power button, the computer shuts down or goes to
sleep.
m The monitor power button shuts down or puts to sleep both the monitor and your
computer. To change the monitor power button setting so that it affects the monitor only,
use the Preferences section of the Monitors control panel.
Troubleshooting 17
m You can use the flip-out stand if you want the display to be more portable, such as when
you are giving presentations.
Positioning the Display
If you’re using the flip-out stand, move the display on the desk or table until you can see the
screen clearly; there are no height adjustments.
If you’re using the display with the desktop stand, you can adjust it for your greatest comfort.
Important Before you adjust the display, make sure there is enough slack in the cables. If
you don’t allow enough clearance, the cables or connectors might be damaged.
1
Place the display so the screen faces you.
20
Chapter 4
2
Adjust the height of the display by pulling up or pushing down on the display.
3
Adjust the viewing angle of the monitor by tilting it up or down and turning it left or right on
the desktop stand.
Using Your Display Stands 21
Storing the Keyboard
When the display is attached to the desktop stand, you can store the keyboard on the
keyboard holders, small rubber indentations on the desktop stand.
Keyboard storage pads
Changing the Display Stand
You can use the display with the desktop stand or with the smaller flip-out stand.
Removing the Desktop Stand
1
2
Place a towel or cloth on a clean, flat surface to protect the display once it’s removed from
the stand.
Pull the display up so that the desktop stand is at its maximum height.
If you don’t do this, the desktop stand will automatically rise to its highest position when you
remove the display from the stand.
3
4
5
6
7
Choose Shut Down from the Special menu to turn off your computer and monitor.
Unplug the power cord from the power adapter.
If necessary, remove the locking cable from the security slot on the back of the display.
Unplug the monitor’s DVI and USB cables from the computer.
Unplug any USB cables that are attached to the USB ports on the monitor.
22
Chapter 4
8
9
Remove any cables from the cable guide on the desktop stand.
Use a coin or flathead screwdriver to unscrew the two plastic thumbscrews on the back cover
of the display.
Plastic
thumbscrews
10 Pull the display slightly up and away from the stand.
Warning The desktop stand will automatically rise to its highest position, if it’s not
already at its maximum height. Be careful not to drop the display.
11 Place the display on a clean, flat surface.
12 Store the stand in a safe place.
Using Your Display Stands 23
Attaching the Desktop Stand
1
2
If necessary, remove the flip-out stand.
For instructions, see “Removing the Flip-Out Stand” on page 25.
Lift the display up and hook the three plastic tabs on the top of the desktop stand into the
three openings on the back center area of the display.
First, hook the
display onto
the desktop stand.
Then tighten the
thumbscrews.
3
4
Screw in the two plastic thumbscrews on the bottom of the cover.
Use a coin or flathead screwdriver to tighten the screws. Don’t overtighten the screws; you
might strip the threads.
Place the DVI and USB cables through the cable guide, if desired.
Important Make sure you leave some slack in the cables so you can tilt, swivel, and turn the
display.
5
6
7
8
Connect the DVI and USB cables to the computer.
Connect the keyboard and mouse to the USB ports on the display, if desired.
If you’re using a locking cable, attach it to the security slot on the back of the display.
If desired, use the height, tilt, and swivel adjustments to position the display the way you
want.
9
Plug in the monitor’s power cord.
24
Chapter 4
Attaching the Flip-Out Stand
1
2
If necessary, remove the desktop stand.
For instructions, see “Removing the Desktop Stand” on page 22.
Hook the three plastic tabs on the top cover of the flip-out stand into the three openings on
the back center area of the display.
First, hook the
flip-out stand
onto the back
of the display.
Then, tighten
the thumbscrews.
3
4
Place the bottom part of the cover against the display and screw in the two plastic
thumbscrews.
Use a coin or flathead screwdriver to tighten the screws. Don’t overtighten the screws; you
might strip the threads.
Flip out the stand and place the display with the stand on a flat surface, such as a table or
desk.
5
6
7
8
Connect the DVI and USB cables to the computer.
Connect the keyboard and mouse to the USB ports on the display, if desired.
If desired, attach a locking cable to the security slot on the back of the display.
Plug in the monitor’s power cord.
Removing the Flip-Out Stand
1
Place a towel or cloth on a clean, flat surface to protect the display once it’s removed from
the stand.
2
3
Choose Shut Down from the Special menu to turn off your computer and monitor.
If necessary, lift the display up slightly and press the power button (®) to turn the display
off.
Using Your Display Stands 25
4
5
6
7
8
Unplug the power cord from the power adapter.
If necessary, remove the locking cable from the security slot on the back of the display.
Unplug the monitor’s DVI and USB cables from the computer.
Unplug any USB cables that are attached to the USB ports on the monitor.
Use a coin or flathead screwdriver to unscrew the two plastic thumbscrews connecting the
flip-out stand to the display.
Plastic
thumbscrews
9
With one hand holding the display, use your other hand to move the flip-out stand slightly
downward to disconnect the three plastic tabs from the three openings on the back center
area of the display.
10 Place the display on a clean, flat surface.
11 Store the flip-out stand in a safe place.
26
Chapter 4
C H A P T E R
5
5
Safety, Health, and Maintenance
Disconnect the power plug (by pulling the plug, not the cord) if any of the following
conditions exists:
m The power cord or plug becomes frayed or otherwise damaged.
m You spill something into the case.
m Your display is exposed to rain or any other excess moisture.
m Your display has been dropped or the case has been otherwise damaged.
m You suspect that your display needs service or repair.
m You want to clean the case or screen. (Use only the recommended procedures. See
“Cleaning the Screen and Case” on page 29.)
Be sure that you always follow these instructions:
m Keep your display away from sources of liquids and moisture.
m Keep the display’s vents free from obstruction.
m Don’t hang anything on the display.
m Keep these instructions handy for reference by you and others.
m Follow all instructions and warnings dealing with your system.
Warning Never remove the case from the display or power adapter! You could come in
contact with hazardous voltage. Electrical equipment may be hazardous if misused.
Operation of this product, or similar products, must always be supervised by an adult. Do
not allow children access to the interior of any electrical product and do not permit them
to handle any cables.
27
Healthy Use of Your Computer Equipment
Use the following illustration to help you in positioning your monitor.
45–70 cm (18–28 in.)
Shoulders relaxed
Top of the screen at or slightly
below eye level (You may need
to adjust the height of your
display)
Forearms and hands
in a straight line
Forearms level or
tilted down slightly
Tilt screen to avoid
reflected glare
Lower back supported
Thighs tilted slightly
Clearance under work surface
Feet flat on the floor
Here are some guidelines for adjusting the furniture in your work area to accommodate your
physical size and shape.
m An adjustable chair that provides firm, comfortable support is best. Adjust the height of
the chair so your thighs are horizontal and your feet flat on the floor. The back of the
chair should support your lower back (lumbar region). Follow the manufacturer’s
instructions for adjusting the backrest to fit your body properly.
m When you use the computer keyboard, your shoulders should be relaxed. Your upper arm
and forearm should form an approximate right angle or be tilted down slightly, with your
wrist and hand in roughly a straight line. Make sure the armrests of your chair don’t
interfere with your positioning. You may have to raise your chair so your forearms and
hands are at the proper angle to the keyboard. If this makes it impossible to rest your feet
flat on the floor, you can use a footrest with adjustable height and tilt to make up for any
gap between the floor and your feet. Or try lowering the desktop to eliminate the need
for a footrest. Another option is to use a desk with a keyboard tray that is lower than the
regular work surface.
m Position the mouse at the same height as your keyboard. Allow adequate space to use the
mouse comfortably to the immediate right or left.
m Position the monitor directly in front of you with the keyboard directly in line with the
monitor. The best distance from your eyes to the screen is up to you, although most
people seem to prefer 18 to 28 inches (45 to 70 cm).
28
Chapter 5
m Position the monitor to minimize glare and reflections on the screen from overhead lights
and windows. Tilt the monitor to the best angle for viewing, helping to reduce or
eliminate glare from lighting sources you can’t move.
m Adjust the brightness of the screen to ensure the best image quality and viewing comfort.
For more health and safety information about your computer equipment, choose Mac Help
from the Help menu in the Finder. You can also see the following (English only) World Wide
Web site:
General Maintenance
To maintain your Apple Studio Display and ensure its long life:
m Do not block the display’s vents.
m Do not let liquid get on or into the display.
m Do not press on the surface of the display screen.
m Do not write on the screen or touch the screen with a sharp object.
m Turn off your monitor when the computer is idle for a prolonged time.
m If you will not be using your display and computer for a day or more, turn off the
computer and display or use Energy Saver.
Important Using a screen-saver program will reduce the lifespan of the monitor’s
backlighting.
Cleaning the Screen and Case
If you need to clean the screen or case beyond wiping it down with a dry cloth, follow these
instructions:
1
2
3
4
Turn your computer and display off.
Disconnect the display’s power cord from the electrical outlet or power strip.
Disconnect the USB and DVI cables from the back of the computer.
Clean the screen with soft, lint-free paper or cloth dampened with mild soap and water.
Warning Do not spray liquid directly onto the display screen. Liquid could drip inside
the display and cause electrical shock.
5
Wipe the case surfaces lightly with a clean, soft cloth dampened with water.
Warning Don’t use alcohol, aerosol sprays, solvents, or abrasives that might damage the
finish on the case.
Safety, Health, and Maintenance 29
Protecting Your Display From Theft
The back of the display has a built-in slot for connecting a security lock. This lets you attach a
narrow, flexible cable that you can use to secure your display to prevent theft. Your monitor
cable also has a security ring that you can use to secure your monitor. Security locks are
available from an Apple-authorized dealer or computer retailer.
F Security slot
Follow the instructions that came with the locking cable to secure it to your display.
Important When you attach a locking cable, make sure you leave enough slack in other
cables attached to the display. If you don’t, you may damage the cables or the connectors
when you adjust the position of the display.
Do You Need to Install a Graphics Card?
Your Apple Studio Display works with a graphics card with a DVI digital-only connector. If
your computer doesn’t have the required graphics card, you must install one to use this
display.
If you are not sure whether your computer or graphics card has the appropriate built-in
video capability, check with an Apple-authorized dealer.
Note: If you’re using more than one display, you may need a graphics card for each display
you are using.
30
Chapter 5
Conserving Energy
You can use the Energy Saver control panel to set your monitor to conserve energy after a
specified period of inactivity. When Energy Saver detects that you’re not using the computer,
the monitor, press any key on the keyboard. For more information about using Energy Saver,
choose Mac Help or Mac OS Help from the Help menu in the Finder. Also see the documents
in the TCO Information folder, located on the CD that came with your monitor, and see
®
ENERGY STAR compliance information in “Power-Saving and Environmental Features” on
page 33.
Safety, Health, and Maintenance 31
A P P E N D I X
Technical Information
General Specifications
Screen
m 15.1-inch (38.4 centimeters) viewable diagonal image, 307 millimeters (mm) horizontal x
230 mm vertical
m 1024 horizontal x 768 vertical active pixels
m Color depth: 8 bit/color, 24 bit
Desktop Stand
m Tilt adjustment: –10 degrees downward and +45 degrees upward
m Swivel adjustment: 45 degrees
m Height adjustment: 4.4 inches (110 mm)
Power-Saving and Environmental Features
The color of the power indicator light on the front of the monitor indicates the operating
mode:
Power
consumption
Mac OS Energy
Saver mode
Power mode
Power indicator
On
Green
<40 watts (W)
<15/5 W
Normal
Standby/
Suspend
Amber
Monitor sleep
Off
Off
<5 W
System sleep
33
For instructions on adjusting the system and display sleep settings and additional energy-
conservation information, see Mac Help.
m TCO/NUTEK: This product has been certified by TCO (the Swedish Confederation of
Professional Employees) to meet the standards for ergonomics, energy efficiency
(NUTEK), emissions, and ecology.
m MPR II: This product meets the strict limits for reduced electromagnetic and electrostatic
emissions.
®
®
m ENERGY STAR : As an ENERGY STAR partner, Apple Computer has determined that this
®
product meets the ENERGY STAR guidelines for energy efficiency. The United States
Environmental Protection Agency’s ENERGY STAR program is a partnership with office
®
product equipment manufacturers to promote energy-efficiency. Reducing energy
consumption of office products saves money and reduces pollution by eliminating wasted
energy.
Weight
m Display: 6 pounds (2.7 kilograms)
m Desktop stand: 4.6 pounds (2.08 kilograms)
Dimensions of Display (With Desktop Stand)
m Minimum height: 15.0 inches (in.) 0.2 in. (375 mm 5 mm)
m Maximum height: 19.3 in. 0.2 in. (483 mm 5 mm)
m Width: 15.7 in. 0.2 in. (393.6 mm 5 mm)
m Depth: 9.8 in. 0.2 in. (249 mm 5 mm)
Dimensions of Display (With Flip-Out Stand)
m Height: 11.6 in. 0.2 in. (297 mm 5mm)
m Width: 15.7 in. 0.2 in. (393.6 mm 5 mm)
m Depth: 6.9 in. 0.2 in. (184.5 mm 5 mm)
Temperature
m Operating: 50˚ to 95˚ F (10˚ to 35˚ C)
m Storage (up to 6 months): –4˚ to 140˚ F (–20˚ to 60˚ C)
m Shipping (up to 72 hours): –40˚ to 149˚ F (–40˚ to 65˚ C)
34 Appendix
Humidity (Noncondensing)
m Operating: 20% to 80%
m Storage (up to 6 months): 20% to 80%
m Shipping (up to 72 hours): 20% to 80%
Altitude
m Operating: 0 to 10,000 feet (0 to 3,030 meters)
m Shipping: 0 to 35,000 feet (0 to 10,606 meters)
Active Video Image Area
The recommended resolution for your monitor is 1024 x 768. You can choose other standard
resolutions that are scaled to fit your monitor’s screen size. Resolutions supported for
computer input:
Input resolution
Output size from scaler
Vertical refresh rate (Hertz)
640 x 480
1024 x 768
75.0
800 x 600
1024 x 768
1024 x 768
75.0
60
1024 x 768
Note: The number of resolutions that your computer supports may be different from those
listed here. Your computer may not support all resolutions.
Power Adapter Electrical Requirements
m Input: 100–240 volts (V) alternating current, 50–60 hertz (Hz) 1.2 amp
m Output: 24 V direct current, 1.875 amp
Interfaces
m Two self-powered USB ports supporting USB input devices (such as a keyboard, mouse,
or trackball)
™
m VESA Display Data Channel (DDC) Standard: This display supports VESA DDC 2B.
Technical Information 35
Display Cable Specifications
m DVI digital-only connector
The digital-only connector contains 24 signal contacts organized in three rows of 8
contacts.
Pin
Signal assignment
Pin
Signal assignment
Pin
Signal assignment
1
TMDS Data2-
9
TMDS Data1-
17
TMDS Data0-
2
3
4
5
6
7
8
TMDS Data2+
TMDS Data2 Shield
No Connect
No Connect
DDC Clock
10
11
12
13
14
15
16
TMDS Data1+
TMDS Data1 Shield
No Connect
18
19
20
21
22
23
24
TMDS Data0+
TMDS Data0 Shield
No Connect
No Connect
No Connect
+5 V Power
TMDS Clock Shield
TMDS Clock +
TMDS Clock -
DDC Data
Ground (for +5 V)
Hot Plug Detect
No Connect
36 Appendix
Communications Regulation Information
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with
the specifications in Part 15 of FCC rules. See instructions if interference to radio or television reception is
suspected.
Radio and Television Interference
The equipment described in this manual generates, uses, and can radiate radio-frequency energy. If it is not
installed and used properly—that is, in strict accordance with Apple’s instructions—it may cause interference with
radio and television reception.
This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with
the specifications in Part 15 of FCC rules. These specifications are designed to provide reasonable protection
against such interference in a residential installation. However, there is no guarantee that interference will not occur
in a particular installation.
You can determine whether your computer system is causing interference by turning it off. If the interference stops,
it was probably caused by the computer or one of the peripheral devices.
If your computer system does cause interference to radio or television reception, try to correct the interference by
using one or more of the following measures:
m Turn the television or radio antenna until the interference stops.
m Move the computer to one side or the other of the television or radio.
m Move the computer farther away from the television or radio.
m Plug the computer into an outlet that is on a different circuit from the television or radio. (That is, make certain
the computer and the television or radio are on circuits controlled by different circuit breakers or fuses.)
If necessary, consult an Apple-authorized service provider or Apple. See the service and support information that
came with your Apple product. Or, consult an experienced radio/television technician for additional suggestions.
Important Changes or modifications to this product not authorized by Apple Computer, Inc., could void the FCC
Certification and negate your authority to operate the product.
This product was tested for FCC compliance under conditions that included the use of Apple peripheral devices and
Apple shielded cables and connectors between system components. It is important that you use Apple peripheral
devices and shielded cables and connectors between system components to reduce the possibility of causing
interference to radios, television sets, and other electronic devices. You can obtain Apple peripheral devices and the
proper shielded cables and connectors through an Apple-authorized dealer. For non-Apple peripheral devices,
contact the manufacturer or dealer for assistance.
Responsible party (contact for FCC matters only): Apple Computer, Inc., Product Compliance, 1 Infinite Loop
M/S 26-A, Cupertino, CA 95014-2084, 408-974-2000.
Industry Canada Statement
This Class B device meets all requirements of the Canadian interference-causing equipment regulations.
Cet appareil numérique de la Class B respecte toutes les exigences du Règlement sur le matériel brouilleur du
Canada.
VCCI Class 2 Statement
37
|