Acer LCD Monitor UM HG6AA D02 User Manual

Acer LCD Monitor  
User Guide  
iii  
Information for your safety and  
comfort  
Safety instructions  
Read these instructions carefully. Keep this document for future reference.  
Follow all warnings and instructions marked on the product.  
Special notes on LCD monitors  
The following are normal with the LCD monitor and do not indicate a problem.  
Due to the nature of the fluorescent light, the screen may flicker during  
initial use. Turn off the power switch and then turn it on again to make  
sure the flicker disappears.  
You may find slightly uneven brightness on the screen depending on the  
desktop pattern you use.  
The LCD screen has 99.99% or more effective pixels. It may include  
blemishes of 0.01% or less such as a missing pixel or a pixel lit all the time.  
Due to the nature of the LCD screen, an afterimage of the previous screen  
may remain after switching the image, when the same image is displayed  
for hours. In this case, the screen is recovered slowly by changing the image  
or turning off the power switch for a few hours.  
Cleaning your monitor  
Please carefully follow these guidelines when cleaning the monitor:  
Always unplug the monitor before cleaning.  
Use a soft cloth to wipe the screen and cabinet front and sides.  
iv  
Accessibility  
Be sure that the power outlet you plug the power cord into is easily accessible  
and located as close to the equipment operator as possible. When you need to  
disconnect power from the equipment, be sure to unplug the power cord from  
the electrical outlet.  
Safe listening  
To protect your hearing, follow these instructions.  
Gradually increase the volume until you can hear it clearly and comfortably  
and without distortion.  
After setting the volume level, do not increase it after your ears have  
adjusted.  
Limit the amount of time listening to music at high volume.  
Avoid turning up the volume to block out noisy surroundings.  
Turn the volume down if you can't hear people speaking near you.  
Warnings  
Do not use this product near water.  
Do not place this product on an unstable cart, stand or table. If the product  
falls, it could be seriously damaged.  
Slots and openings are provided for ventilation to ensure reliable  
operation of the product and to protect it from overheating. These  
openings must not be blocked or covered. The openings should never be  
blocked by placing the product on a bed, sofa, rug or other similar surface.  
This product should never be placed near or over a radiator or heat  
register, or in a built-in installation unless proper ventilation is provided.  
Never push objects of any kind into this product through cabinet slots as  
they may touch dangerous voltage points or short-out parts that could  
result in a fire or electric shock. Never spill liquid of any kind onto or into  
the product.  
To avoid damage of internal components and to prevent battery leakage,  
do not place the product on a vibrating surface.  
Never use it under sporting, exercising, or any vibrating environment  
which will probably cause unexpected short current or damage internal  
devices.  
The adapter is only used for this monitor ,do not be used for other purposes.  
Your device uses one of the following power supplies:  
Manufacturer: Asian Power Devices Inc., Model: DA-40A19  
Manufacturer: Delta Electronics Inc., Model: ADP-40PH BB  
Using electrical power  
This product should be operated from the type of power indicated on the  
marking label. If you are not sure of the type of power available, consult  
your dealer or local power company.  
Do not allow anything to rest on the power cord. Do not locate this  
product where people will walk on the cord.  
If an extension cord is used with this product, make sure that the total  
v
ampere rating of the equipment plugged into the extension cord does not  
exceed the extension cord ampere rating. Also, make sure that the total  
rating of all products plugged into the wall outlet does not exceed the fuse  
rating.  
Do not overload a power outlet, strip or receptacle by plugging in too  
many devices. The overall system load must not exceed 80% of the branch  
circuit rating. If power strips are used, the load should not exceed 80% of  
the power strip's input rating.  
This product's power cord is equipped with a three-wire grounded plug.  
The plug only fits in a grounded power outlet. Make sure the power outlet  
is properly grounded before inserting the power cord plug. Do not insert  
the plug into a non-grounded power outlet. Contact your electrician for  
details.  
Warning! The grounding pin is a safety feature. Using a power  
outlet that is not properly grounded may result in electric shock  
and/or injury.  
Note: The grounding pin also provides good protection from  
unexpected noise produced by other nearby electrical devices that  
may interfere with the performance of this product.  
Use the product only with the supplied power supply cord set. If you need  
to replace the power cord set, make sure that the new power cord meets  
the following requirements: detachable type, UL listed/CSA certified, type  
SPT-2, rated 7 A 125 V minimum, VDE approved or its equivalent, 4.6  
meters (15 feet) maximum length.  
Product servicing  
Do not attempt to service this product yourself, as opening or removing covers  
may expose you to dangerous voltage points or other risks. Refer all servicing to  
qualified service personnel.  
Unplug this product from the wall outlet and refer servicing to qualified service  
personnel when:  
the power cord or plug is damaged, cut or frayed  
liquid was spilled into the product  
the product was exposed to rain or water  
the product has been dropped or the case has been damaged  
the product exhibits a distinct change in performance, indicating a need  
for service  
the product does not operate normally after following the operating  
instructions  
vi  
Note: Adjust only those controls that are covered by the operating  
instructions, since improper adjustment of other controls may  
result in damage and will often require extensive work by a  
qualified technician to restore the product to normal condition.  
Potentially explosive environments  
Switch off your device in any area with a potentially explosive atmosphere and  
obey all signs and instructions. Potentially explosive atmospheres include areas  
where you would normally be advised to turn off your vehicle engine. Sparks in  
such areas could cause an explosion or fire resulting in bodily injury or even  
death. Switch off the device near gas pumps at service stations. Observe  
restrictions on the use of radio equipment in fuel depots, storage and  
distribution areas; chemical plants; or where blasting operations are in progress.  
Areas with a potentially explosive atmosphere are often, but not always,  
marked. They include below deck on boats, chemical transfer or storage  
facilities, vehicles using liquefied petroleum gas (such as propane or butane),  
and areas where the air contains chemicals or particles such as grain, dust or  
metal powders.  
Additional safety information  
Your device and its enhancements may contain small parts. Keep them out of  
the reach of small children.  
IT Equipment Recycling Information  
Acer is strongly committed to environmental protection and views recycling, in  
the form of salvaging and disposal of used equipment, as one of the company's  
top priorities in minimizing the burden placed on the environment.  
We at Acer are very conscious of the environmental effects of our business and  
strive to identify and provide the best working procedures to reduce the  
environmental impact of our products.  
For more information and help when recycling, please go to this website:  
Visit  
of our other products.  
for further information on the features and benefits  
Disposal instructions  
Do not throw this electronic device into the trash when discarding.  
To minimize pollution and ensure utmost protection of the global  
environment, please recycle. For more information on the Waste  
from Electrical and Electronics Equipment (WEEE) regulations, visit  
vii  
LCD pixel statement  
The LCD unit is produced with high-precision manufacturing techniques.  
Nevertheless, some pixels may occasionally misfire or appear as black or  
red dots. This has no effect on the recorded image and does not constitute  
a malfunction.  
This product has been shipped enabled for power management:  
Activate display’s Sleep mode within 15 minutes of user inactivity.  
Activate computer’s Sleep mode within 30 minutes of user inactivity.  
Wake the computer from Sleep mode by pushing the power button.  
Tips and information for comfortable use  
Computer users may complain of eyestrain and headaches after prolonged use.  
Users are also at risk of physical injury after long hours of working in front of a  
computer. Long work periods, bad posture, poor work habits, stress,  
inadequate working conditions, personal health and other factors greatly  
increase the risk of physical injury.  
Incorrect computer usage may lead to carpal tunnel syndrome, tendonitis,  
tenosynovitis or other musculoskeletal disorders. The following symptoms may  
appear in the hands, wrists, arms, shoulders, neck or back:  
numbness, or a burning or tingling sensation  
aching, soreness or tenderness  
pain, swelling or throbbing  
stiffness or tightness  
coldness or weakness  
If you have these symptoms, or any other recurring or persistent discomfort  
and/or pain related to computer use, consult a physician immediately and  
inform your company's health and safety department.  
The following section provides tips for more comfortable computer use.  
Finding your comfort zone  
Find your comfort zone by adjusting the viewing angle of the monitor, using a  
footrest, or raising your sitting height to achieve maximum comfort. Observe  
the following tips:  
refrain from staying too long in one fixed posture  
avoid slouching forward and/or leaning backward  
stand up and walk around regularly to remove the strain on your leg  
muscles  
viii  
Taking care of your vision  
Long viewing hours, wearing incorrect glasses or contact lenses, glare, excessive  
room lighting, poorly focused screens, very small typefaces and low-contrast  
displays could stress your eyes. The following sections provide suggestions on  
how to reduce eyestrain.  
Eyes  
Rest your eyes frequently.  
Give your eyes regular breaks by looking away from the monitor and  
focusing on a distant point.  
Blink frequently to keep your eyes from drying out.  
Display  
Keep your display clean.  
Keep your head at a higher level than the top edge of the display so your  
eyes point downward when looking at the middle of the display.  
Adjust the display brightness and/or contrast to a comfortable level for  
enhanced text readability and graphics clarity.  
Eliminate glare and reflections by:  
placing your display in such a way that the side faces the window or  
any light source  
minimizing room light by using drapes, shades or blinds  
using a task light  
changing the display's viewing angle  
using a glare-reduction filter  
using a display visor, such as a piece of cardboard extended from the  
display's top front edge  
Avoid adjusting your display to an awkward viewing angle.  
Avoid looking at bright light sources, such as open windows, for extended  
periods of time.  
Developing good work habits  
Develop the following work habits to make your computer use more relaxing  
and productive:  
Take short breaks regularly and often.  
Perform some stretching exercises.  
Breathe fresh air as often as possible.  
Exercise regularly and maintain a healthy body.  
UNPACKING  
Please check the following items are present when you unpack the box, and  
save the packing materials in case you will need to ship or transport the  
monitor in future.  
z LCD Monitor  
z
AC Power Cord  
z
D-Sub Cable  
(Optional)  
z
DVI Cable (Optional)  
z
AC Adapter  
z
User Manual  
z
Quick Start Guide  
LCD monitor  
EN-1  
 
ATTACHING / REMOVING THE BASE  
Note: Remove the monitor and monitor base from its packaging.  
Carefully place the monitor face-down on a stable surface -- use a  
cloth to avoid scratching the screen.  
1.  
Attach the monitor stand arm to the Ensure that the base is locked onto the  
base. monitor stand arm.  
2.  
D-Sub  
DVI  
HDMI  
D
C
I
N
D-Sub  
DVI  
HDMI  
D
C
I
N
SCREEN POSITION ADJUSTMENT  
In order to optimize the best viewing position, you can adjust the tilt of the  
monitor by using both of your hands to hold the edges of the monitor as  
shown in the figure below.  
The monitor can be adjusted to 15 degrees up or 5 degrees down as indicated  
by arrow below.  
EN-2  
   
CONNECTING THE POWER CORD  
z
z
z
z
z
Check first to make sure that the power cord you use is the correct type  
required for your area.  
This monitor has a universal power supply that allows operation in either  
100/120V AC or 220/240 V AC voltage area. No user-adjustment is required.  
Plug one end of the AC power cord to the adapter, and plug the other end  
into an AC outlet.  
For unit using at 120 V AC:  
Use a UL Listed Cord Set, Type SVT wire and plug rated 10 A/125 V.  
For unit using at 220/240 V AC (outside of U.S.):  
Use a Cord Set consisting of H05VV-F cord and plug rated 10 A, 250 V. The  
cord set should have the appropriate safety approvals for the country in  
which the equipment will be installed.  
SAFETY PRECAUTION  
z
Avoid placing the monitor, or any other heavy object, on the power cord  
to avoid damage to the cable.  
z
z
Do not expose the monitor to rain, excessive moisture, or dust.  
Do not cover the ventilation slots or openings of the monitor. Always put  
the monitor in a place where there is adequate ventilation.  
Avoid placing the monitor against a bright background or where sun-light  
or other light sources may reflect on the face of the monitor. Place the  
monitor just below eye level.  
z
z
z
Handle with care when transporting the monitor.  
Refrain from giving shock or scratch to the screen, as screen is fragile.  
CLEANING YOUR MONITOR  
Please carefully follow the below guidelines when cleaning the monitor.  
z
Always unplug the monitor before cleaning.  
z
Use a soft cloth to wipe the screen and cabinet front and sides.  
EN-3  
     
POWER SAVING  
The monitor will be driven into Power Saving” mode by the control signal  
from the display controller, as indicated by the amber-color power LED.  
State  
ON  
LED Light  
Blue  
Power Saving Mode  
Amber  
The power saving states will be kept until a control signal has been detected  
or the keyboard or mouse is activated. The recovery time from Active OFF  
state back to ON state is around 3 seconds.  
DDC  
To make your installation easier, the monitor is able to Plug and Play with  
your system if your system also supports DDC protocol. The DDC (Display Data  
Channel) is a communication protocol through which the monitor  
automatically informs the host system about its capabilities, for example,  
supported resolutions and corresponding timing. The monitor supports  
DDC2B standard.  
EN-4  
   
CONNECTOR PIN ASSIGNMENT  
15-Pin Color Display Signal Cable  
PIN NO.  
DESCRIPTION  
Red  
PIN NO.  
9.  
DESCRIPTION  
+5V  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
Green  
10.  
Logic Ground  
Monitor Ground  
DDC-Serial Data  
H-Sync  
Blue  
11.  
Monitor Ground  
DDC-return  
R-Ground  
G-Ground  
B-Ground  
12.  
13.  
14.  
V-Sync  
15.  
DDC-Serial Clock  
EN-5  
 
24-Pin Color Display Signal Cable*  
PIN  
1.  
Meaning  
TMDS Data2-  
TMDS Data2+  
TMDS Data 2/4 Shield  
NC  
PIN  
13.  
14.  
15.  
16.  
17.  
18.  
19.  
20.  
21.  
22.  
23.  
24.  
Meaning  
NC  
2.  
+5V Power  
3.  
Logic Ground  
Hot Plug Detect  
TMDS Data0-  
TMDS Data0+  
TMDS Data 0/5 Shield  
NC  
4.  
5.  
NC  
6.  
DDC Clock  
DDC Data  
7.  
8.  
NC  
9.  
TMDS Data1-  
TMDS Data1+  
TMDS Data 1/3 Shield  
NC  
NC  
10.  
11.  
12.  
TMDS Clock Shield  
TMDS Clock+  
DDC TMDS Clock-  
19-Pin Color Display Signal Cable*  
PIN  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
9.  
Meaning  
TMDS Data2+  
PIN  
10.  
11.  
12.  
13.  
14.  
15.  
16.  
17.  
18.  
19.  
Meaning  
TMDS Clock+  
TMDS Clock Shield  
TMDS Clock-  
CEC  
TMDS Data2 Shield  
TMDS Data2-  
TMDS Data1+  
TMDS Data1 Shield  
TMDS Data1-  
Reserved (N.C. on device)  
SCL  
TMDS Data0+  
SDA  
TMDS Data0 Shield  
TMDS Data0-  
DDC/CEC Ground  
+5V Power  
Hot Plug Detect  
* only for certain models  
EN-6  
STANDARD TIMING TABLE  
Mode  
Resolution  
1
640 x 480  
60  
66.66  
70  
56  
60  
60  
70  
75  
60  
60  
60  
60  
60  
60  
60  
Hz  
Hz  
Hz  
Hz  
Hz  
Hz  
Hz  
Hz  
Hz  
Hz  
Hz  
Hz  
Hz  
Hz  
Hz  
2
MAC  
640 x 480  
3
VESA  
720 x 400  
4
SVGA  
SVGA  
XGA  
800 x 600  
5
800 x 600  
6
1024 x 768  
1024 x 768  
1152 x 864  
1280 x1024  
1280 x 720  
1280 x 800  
1440 x 900  
1680 x 1050  
1920 x 1080  
1920 x 1080  
7
XGA  
8
VESA  
9
SXGA  
VESA  
10  
11  
12  
13  
14  
15  
WXGA  
WXGA+  
WSXGA+  
UXGA  
UXGA  
EN-7  
 
INSTALLATION  
To install the monitor to your host system, please follow the steps as given  
below:  
Steps  
1. 1-1 Connect Video Cable  
a. Make sure both the monitor and computer are powered-OFF.  
b. Connect the VGA video cable to the computer.  
1-2 Connect Digital Cable (Only Dual-input model)  
a. Make sure both the monitor and computer are powered-OFF.  
b. Connect one end of the 24-pin DVI cable to the back of the monitor  
and connect the other end to the computer’s port.  
1-3 Connect HDMI Cable (Only HDMI-input model)  
a. Make sure both the monitor and computer are powered-OFF.  
b. Connect the HDMI cable to the computer.  
2. Connect the adapter  
a. Connect the AC cord to the adapter.  
b. Connect one end of the adapter to the monitor and the other end to  
a properly grounded, AC outlet.  
3. Power-ON Monitor and Computer  
Power-ON the monitor first, then power-ON the computer.  
This sequence is very important.  
4. If the monitor still does not function properly, please refer to the  
troubleshooting section to diagnose the problem.  
DC IN  
HDMI  
DVI  
D-Sub  
DC  
D-Sub  
DVI  
HDMI  
HDMI  
DVI  
D-Sub  
DC IN  
EN-8  
 
USER CONTROLS  
Base Controls  
Power Switch / Power LED:  
To turn the monitor ON or OFF.  
Lights up to indicate the power is turned ON.  
W / X Minus / Plus:  
If the OSD is active, press the Minus or Plus buttons to toggle between the OSD  
options.  
MENU OSD functions  
Press this botton to activate the OSD menu.  
AUTO Auto Adjust:  
Press this button to activate the Auto Adjustment function. The Auto Adjustment  
function is used to set the HPos, VPos, Clock and Focus.  
Empowering:  
Press the Empowering Key to open the Acer eColor Management OSD and access the  
scenario modes.  
EN-9  
 
Acer eColor Management  
Operation instructions  
Step 1: Press “  
” Key to open the Acer eColor Management OSD and access  
the scenario modes  
Step 2: Press “W“ or “X” to select the mode  
Step 3: Press “ AUTO “ Key to confirm the mode and run Auto Adjust.  
Features and Benefits  
Main  
Menu icon  
Sub Menu Sub Menu  
Description  
icon  
item  
User defined. Settings can be fine-tuned to  
suit any situation  
N/A  
User mode  
Adjusts the settings to reduce power  
consumption.  
N/A  
N/A  
ECO mode  
Standard  
mode  
Default Setting. Reflects native display  
capability  
Enhances colors and emphasize fine detail.  
Pictures and photographs appear in vibrant  
colors with sharp detail.  
Grahpic  
mode  
N/A  
N/A  
Displays scenes in clearest detail. Presents  
great visuals, even in unsuitably-lit  
environments.  
Movie  
mode  
EN-10  
Adjusting the OSD settings  
Note: The following content is for general reference only. Actual  
product specifications may vary.  
The OSD can be used for adjusting the settings of your LCD Monitor.  
Press the MENU key to open the OSD. You can use the OSD to adjust the  
picture quality, OSD position and general settings. For advanced settings,  
please refer to following page:  
Adjusting the picture quality  
1 Press the MENU key to bring up the OSD.  
2 Using the e/ f keys, select  
Picture from the OSD. Then navigate to the  
picture element you wish to adjust.  
3 Use the e/ f keys to adjust the sliding scales.  
4 The Picture menu can be used to adjust the current Brightness, Contrast,  
Colour Temp, Auto Config and other image-related qualities.  
EN-11  
Adjusting the OSD position  
1 Press the MENU key to bring up the OSD.  
2 Using the directional keys, select  
OSD from the on screen display. Then  
navigate to the feature you wish to adjust.  
EN-12  
Adjusting the setting  
1 Press the MENU key to bring up the OSD.  
2 Using the e/ f keys, select  
Setting from the OSD. Then navigate to  
the feature you wish to adjust.  
3 The Setting menu can be used to adjust the screen Menu Language and  
other important settings.  
EN-13  
Product information  
1 Press the MENU key to bring up the OSD.  
2 Using the e/ f keys, select  
Information from the OSD. Then the basic  
information of LCD monitor will show up for current input.  
EN-14  
TROUBLESHOOTING  
Before sending your LCD monitor for servicing, please check the trouble-  
shooting list below to see if you can self-diagnose the problem.  
(VGA Mode)  
Problems  
Current Status  
LED ON  
Remedy  
z
Using OSD, adjust brightness and  
No Picture  
contrast to maximum or reset to  
their default settings.  
z
z
Check the power switch.  
Check if AC power cord is properly  
connected to the monitor.  
LED OFF  
z
Check if video signal cable is  
properly connected at the back of  
monitor.  
LED displays amber color  
z
z
Check if the power of computer  
system is ON.  
Check if the specification of graphics  
adapter and monitor is in  
compliance which may be causing  
the input signal frequency  
mismatch.  
Abnormal  
Picture  
Unstable Picture  
z
z
z
Using OSD, adjust RESOLUTION,  
CLOCK, CLOCK-PHASE, H-POSITION  
and V-POSITION with non-standard  
signals.  
Using OSD, in case of missing full-  
screen image, please select other  
resolution or other vertical refresh  
timing.  
Wait for a few seconds after  
adjusting the size of the image  
before changing or disconnecting  
the signal cable or powering OFF the  
monitor.  
Display is missing, center  
shift, or too small or too  
large in display size  
EN-15  
 
(DVI/HDMI Mode)  
Problems  
Current Status  
LED ON  
Remedy  
z
Using OSD, adjust brightness  
No Picture  
and contrast to maximum or  
reset to their default settings.  
z
z
Check the power switch.  
LED OFF  
Check if AC power cord is  
properly connected to the  
monitor.  
z
z
Check if video signal cable is  
properly connected at the back  
of monitor.  
Check if the power of computer  
system is ON.  
LED displays amber color  
EN-16  
Acer Incorporated  
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi  
New Taipei City 221, Taiwan  
Declaration of Conformity  
We,  
Acer Incorporated  
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan  
Contact Person: Mr. RU Jan, e-mail: [email protected]  
And,  
Acer Italy s.r.l  
Via Lepetit, 40, 20020 Lainate (MI) Italy  
Tel: +39-02-939-921, Fax: +39-02 9399-2913  
Hereby declare that:  
Product:  
LCD Monitor  
Trade Name:  
Model Number:  
SKU Number:  
Acer  
G276HL  
G276HL xxxxxx (“x” = 0~9, a ~ z, or A ~ Z)  
Is compliant with the essential requirements and other relevant provisions of the following EC directives,  
and that all the necessary steps have been taken and are in force to assure that production units of the same  
product will continue comply with the requirements.  
EMC Directive 2004/108/EC as attested by conformity with the following harmonized standards:  
-. EN55022, AS/NZS CISPR22 Class B.  
-. EN55024  
-. EN61000-3-2, Class D  
-. EN61000-3-3  
Low Voltage Directive 2006/95/EC as attested by conformity with the following harmonized  
standard:  
-. EN60950-1  
RoHS Directive 2002/95/EC on the Restriction of the Use of certain Hazardous Substances in  
Electrical and Electronic Equipment:  
-. The maximum concentration values of the restricted substances by weight in homogenous material are:  
Lead  
0.1% Polybrominated Biphenyls (PBB’s)  
0.1%  
0.1%  
0.01%  
Mercury  
0.1% Polybrominated Diphenyl Ethers (PBDE’s)  
Hexavalent Chromium 0.1% Cadmium  
Directive 2009/125/EC with regard to establishing a framework for the setting of ecodesign  
requirements for energy-related product.  
Year to begin affixing CE marking 2012.  
Mar. 30, 2012  
Date  
RU Jan / Sr. Manager  
Regulation, Acer Inc.  
EN-17  
Acer America Corporation  
333 West San Carlos St., San Jose  
CA 95110, U. S. A.  
Tel : 254-298-4000  
Fax : 254-298-4147  
Federal Communications Commission  
Declaration of Conformity  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  
(1) this device may not cause harmful interference, and (2) this device must accept any interference  
received, including interference that may cause undesired operation.  
The following local Manufacturer /Importer is responsible for this declaration:  
Product:  
LCD Monitor  
G276HL  
Model Number:  
SKU Number:  
G276HL xxxxxx  
(“x” = 0~9, a ~ z, or A ~ Z)  
Name of Responsible Party:  
Address of Responsible Party:  
Acer America Corporation  
333 West San Carlos St.  
San Jose, CA 95110  
U. S. A.  
Contact Person:  
Phone No.:  
Fax No.:  
Acer Representative  
254-298-4000  
254-298-4147  
EN-18  
ENERGY STAR®  
Acer’s ENERGY STAR qualified products save you money by reducing energy  
costs and helps protect the environment without sacrificing features or  
performance. Acer is proud to offer our customers products with the ENERGY  
STAR mark.  
What is ENERGY STAR?  
Products that are ENERGY STAR qualified use less energy and prevent  
greenhouse gas emissions by meeting strict energy efficiency guidelines set by  
the U.S. Environmental Protection Agency. Acer is committed to offer products  
and services worldwide that help customers save money, conserve energy and  
improve the quality of our environment. The more energy we can save through  
energy efficiency, the more we reduce greenhouse gases and the risks of climate  
Acer ENERGY STAR qualified products:  
• Produce less heat and reduce cooling loads, and warmer climates.  
• Automatically go into “display sleep” and “computer sleep” mode after 15 and 30  
minute of inactivity respectively.  
• Wake the monitor when it is in Active Off mode, move the mouse or press any  
keyboard key.  
• Computers will save more than 80% energy at “sleep” mode.  
ENERGY STAR and the ENERGY STAR mark are registered U.S. marks  
EN-19  

Desa VESBL User Manual
DeLonghi Convection Oven 1761030IDL User Manual
Creda C161E User Manual
Cannon 50cm Free Standing Electric Cooker C50EKW User Manual
Bosch Appliances NEM 95 User Manual
Bertazzoni C36500X User Manual
BenQ Computer Monitor G2220HDA User Manual
AOC USB Monitor E1649FWU User Manual
AMX Modero NXD 500i User Manual
Aluratek SDHC User Manual