.
TABLE OF CONTENTS
FOR YOUR SAFETY -------------------------------------------------- 1
SAFETY PRECAUTIONS -------------------------------------- 2
SPECIAL NOTES ON LCD MONITORS ------------------- 3
BEFORE YOU OPERATE THE MONITOR --------------------- 3
FEATURES -------------------------------------------------------- 3
PACKING LIST --------------------------------------------------- 3
INSTALLATION INSTRUCTIONS --------------------------- 4
CONTROLS AND CONNECTORS -------------------------- 5
ADJUSTING THE VIEWING ANGLE ----------------------- 6
OPERATING INSTRUCTIONS ------------------------------------- 7
GENERAL INSTRUCTIONS ---------------------------------- 7
HOW TO ADJUST A SETTING ------------------------------ 9
ADJUSTING THE PICTURE ----------------------------- 10-11
PLUG AND PLAY ----------------------------------------------- 12
TECHNICAL SUPPORT(FAQ) -------------------------------- 13-14
ERROR MESSAGE & POSSIBLE SOLUTION ------- 15
APPENDIX ------------------------------------------------------------- 16
SPECIFICATIONS ------------------------------------------ 16-17
FACTORY PRESET TIMING TABLE --------------------- 18
CONNECTOR PIN ASSIGNMENT ------------------------ 19
PRECAUTIONS
z Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen
sink, laundry tub, swimming pool or in a wet basement.
z Do not place the monitor on an unstable cart, stand, or table. If the monitor
falls, it can injure a person and cause serious damage to the appliance.
Use only a cart or stand recommended by the manufacturer or sold with
the monitor. If you mount the monitor on a wall or shelf, use a mounting kit
approved by the manufacturer and follow the kit instructions.
z Slots and openings in the back and bottom of the cabinet are provided for
ventilation. To ensure reliable operation of the monitor and to protect it
from overheating, be sure these openings are not blocked or covered. Do
not place the monitor on a bed, sofa, rug, or similar surface. Do not place
the monitor near or over a radiator or heat register. Do not place the
monitor in a bookcase or cabinet unless proper ventilation is provided.
z The monitor should be operated only from the type of power source
indicated on the label. If you are not sure of the type of power supplied to
your home, consult your dealer or local power company.
z The monitor is equipped with a three-pronged grounded plug, a plug with a
third (grounding) pin. This plug will fit only into a grounded power outlet as
a safety feature. If your outlet does not accommodate the three-wire plug,
have an electrician install the correct outlet, or ground the appliance safely.
Do not defeat the safety purpose of the grounded plug.
z Unplug the unit during a lightening storm or when it will not be used for
long period of time. This will protect the monitor from damage due to
power surges.
z Do not overload power strips and extension cords. Overloading can result
in fire or electric shock.
z Never push any object into the slot on the monitor cabinet. It could short
circuit parts causing a fire or electric shock. Never spill liquids on the
monitor.
z Do not attempt to service the monitor by yourself; opening or removing
covers can expose you to dangerous voltages and other hazards. Please
refer all servicing to qualified service personnel.
z To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked
between 100 - 240V AC, Min. 5A.
z The wall socket shall be installed near the equipment and shall be easily
accessible.
z For use only with the attached power adapter (Output 12Vdc) which have
UL, CSA listed license
2
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitor and do not indicate a
problem.
NOTES
•
Due to the nature of the fluorescent light, the screen may flicker during
initial use. Turn off the Power Switch and then turn it on again to make
sure the flicker disappears.
•
•
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
The LCD screen has effective pixels of 99.99% or more. It may include
blemishes of 0.01% or less such as a missing pixel or a pixel lit all of the
time.
•
Due to the nature of the LCD screen, an afterimage of the previous screen
may remain after switching the image, when the same image is displayed
for hours. In this case, the screen is recovered slowly by changing the
image or turning off the Power Switch for hours.
BEFORE YOU OPERATE THE MONITOR
FEATURES
•
•
•
•
•
•
•
43.2cm(17”) TFT Color LCD Monitor
Crisp, Clear Display for Windows
Recommened Resolutions: 1280 X 1024 @60Hz
EPA ENERGY STAR®
Dual Input (DVI + Analog) (Only Dual-Input Model)
Ergonomic Design (TCO’99 Approved)
Space Saving, Compact Case Design
CHECKING THE CONTENTS OF THE PACKAGE
The product package should include the following items:
1. LCD Monitor
2. Owner's Manual
3. Power Cord
4. External Adapter
5. 15-pin D-Sub Cable
6. DVI Cable (only Dual-Input Model)
7. Audio Cable
3
POWERCORD
Power Source:
1. Make sure that the power cord is the correct type required in your area.
2. This LCD monitor has an External universal power supply that allows operation in
either 100/120V AC or 220/240V AC voltage area (No user adjustment is
required.)
3. Connect the AC-power cord into your LCD monitor’ s DC-power-input. The AC-
power cord may be connected to either a wall power outlet or the power outlet
socket on your PC, depending on the type of power cord supplied with your LCD
monitor.
NOTES
A certified power supply cord has to be used with this equipment. The relevant
national installation and/or equipment regulations shall be considered. A certified
power supply cord not lighter than ordinary polyvinyl chloride flexible cord according
to IEC 60227 (designation H05VV-F 3G 0.75mm2 or H05VVH2-F2 3G 0.75mm2)
shall be used. Alternative a flexible cord be of synthetic rubber according to IEC
60245 (designation H05RR-F 3G 0.75mm2) shall be used.
Installing the wall mounting bracket (not included)
This monitor display can be connected to the wall mounting bracket that is sold
separately. Please see the following diagram for information on how to disconnect it
from the power cable and fold the monitor:
Installation of the wall mounting bracket is as follows:
1. Place the wall mounting bracket on the underside of the monitor. Attach to
monitor through the holes in the bracket and on the underside of monitor;
Attach (7.5cm X 7.5cm) as shown in figure a.
2. Place four screws into the holes as shown and tighten;
3. Re-connect the cable. For instructions on how to attach the monitor to the wall,
see the Users’ Manual included with the wall mounting bracket;(This product is
not provided with wall mounting bracket, which is sold seperately)
4. Fighre b shows how the bracket should sit against the wall;
a
b
4
CABLE CONNECTIONS
Turn off your computer before performing the procedure below.
1. Connect the power adapter dc cable to the DC-In port on the back of the
monitor.
2. Connect one end of the 15-pin D-Sub cable to the back of the monitor and
connect the other end to the computer’s D-Sub port.
3. (only Dual-Input Model)Connect one end of the 24-pin DVI cable to the
back of the monitor and connect the other end to the computer’s DVI port.
4. Connect the audio cable between the monitor's audio input and the PC's
audio output (green port).
5. Plug the power cable of your monitor into a nearby outlet. Plug the other
end of the power cord into the power adapter.
6. Turn on your monitor and computer.
Figure 1 Connecting Cables
1. D-SUB Cable
2. DC-Jack Power Cable
3. AC Power Cord
4.
5.
6.
External Adapter
DVI Cable
Audio cable
5
ADJUSTING THE VIEWING ANGLE
•
•
•
For optimal viewing it is recommended to look at the full face of the
monitor, then adjust the monitor’s angle to your own preference.
Hold the stand so you do not topple the monitor when you change the
monitor’s angle.
You can adjust the angle of the monitor from -5° to 15°, but please notice that
the rear obliquity of the monitor must not be over 15° when you adjust it,
otherwise the machine may be inclined.
Figure 2
NOTES
•
•
Do not touch the LCD screen when you change the angle. It may cause
damage or break the LCD screen.
Careful attention is required not to catch your fingers or hands when you
change the angle.
6
OPERATING INSTRUCTIONS
GENERAL INSTRUCTIONS
Press the power button to turn the monitor on or off. The other control buttons
are located at front panel of the monitor (See Figure 3). By changing these
settings, the picture can be adjusted to your personal preferences.
•
•
•
The power cord should be connected.
Connect the video cable from the monitor to the video card.
Press the power button to turn on the monitor position. The power indicator
will light up.
Figure 3
External Control Button
EXTERNAL CONTROLS
1. >/ Volume
2. </ Volume
4.
5.
MENU/ENTER
Auto Adjust Key/Exit
3.
Power Key /Power Indicator
7
FRONT PANEL CONTROL
• Power Button:
Press this button to turn the monitor ON or OFF, And display the monitor’s
state.
• Power Indicator:
Blue
Orange
—
—
Power On mode.
Power off.
• MENU / ENTER :
Activate OSD menu when OSD is OFF or activate/de-activate adjustment
function when OSD is ON or Exit OSD menu when in Volume Adjust OSD
status.
• </Volume:
Activates the volume control when the OSD is OFF or navigate through
adjustment icons when OSD is ON or adjust a function when function is
activated.
• >/Volume:
Activates the volume control when the OSD is OFF or navigate through
adjustment icons when OSD is ON or adjust a function when function is
activated.
•
Auto Adjust button / Exit:
1. When OSD menu is in active status, this button will act as EXIT-KEY
(EXIT OSD menu).
2. When OSD menu is in off status, press this button for 2 seconds to
activate the Auto Adjustment function.
The Auto Adjustment function is used to set the HPos, VPos, Clock
and Focus.
NOTES
•
Do not install the monitor in a location near heat sources such as radiators
or air ducts, or in a place subject to direct sunlight, or excessive dust or
mechanical vibration or shock.
•
•
•
Save the original shipping carton and packing materials, as they will come
in handy if you ever have to ship your monitor.
For maximum protection, repackage your monitor as it was originally
packed at the factory.
To keep the monitor looking new, periodically clean it with a soft cloth.
Stubborn stains may be removed with a cloth lightly dampened with a mild
detergent solution. Never use strong solvents such as thinner, benzene, or
abrasive cleaners, since these will damage the cabinet. As a safety
precaution, always unplug the monitor before cleaning it.
8
HOW TO ADJUST A SETTING
1. Press the MENU-button to activate the OSD window.
2. Press < or > to select the desired function.
3. Press the MENU-button to select the function that you want to adjust.
4. Press < or > to change the settings of the current function.
5. To exit and save, select the exit function. If you want to adjust any other
function, repeat steps 2-4.
I. Analog-Only Model
II. Dual-Input Model, Analog Signal Input
9
III. Dual-Input Model, Digital Signal Input
ADJUSTING THE PICTURE
The descriptions for function control LEDS
Sub
Main
Sub Menu
Item
Menu
Icon
Description
Menu Icon
Adjusts the contrast between the
foreground and background of the screen
image.
Contrast
Adjusts the background brightness of the
screen image.
Brightness
Focus
Adjusts picture Focus (available in Analog
mode only).
Adjusts picture Clock (available in Analog
mode only).
Clock
Adjust picture Focus (available in Analog
mode only).
H. Position
V. Position
Adjust picture Clock (available in Analog
mode only).
N/A Warm
N/A Cool
Set the color temperature to warm white.
Set the color temperature to cool white.
User /Red
Adjusts Red/Green/Blue intensity.
User/Green
User/Blue
10
N/A English
繁體中文
N/A
N/A Deutsch
N/A Français
N/A Español
N/A Italiano
Multi-language selection.
简体中文
日本語
N/A
N/A
H. Position
Adjust the horizontal position of the OSD.
V. Position
Adjust the vertical position of the OSD.
Adjust the OSD timeout.
OSD
Timeout
Auto Adjust the H/V Position, Focus and
Clock of picture.
(only
Analog-
input
N/A Auto Config
Model)
N/A Analog
N/A Digital
Select input signal from analog (D-Sub)
Select input signal from digital (DVI)
(only Dual-
Input
Model)
Show the resolution, H/V frequency and
input port of current iput timing.
N/A Information
N/A Reset
N/A Exit
Clear each old status of Auto-configuration
and set the color temperature to Cool.
Save user adjustment and OSD disappear.
11
PLUG AND PLAY
Plug & Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the
VESA DDC STANDARD. It allows the monitor to inform the host system of its
identity and, depending on the level of DDC used, communicate additional
information about its display capabilities.
The DDC2B is a bidirectional data hannel based on the I2C protocol. The
host can request EDID information over the DDC2B channel.
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS
NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE
PROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL.
This monitor meets the Green monitor standards as set by the Video
Electronics Standards Association (VESA) and/or the United States
Environmental Protection Agency (EPA) and The Swedish Confederation
Employees (NUTEK). This feature is designed to conserve electrical energy
by reducing power consumption when there is no video-input signal present.
When there is no video input signal this monitor, following a time-out period,
will automatically switch to an OFF mode. This reduces the monitor's internal
power supply consumption. After the video input signal is restored, full power
is restored and the display is automatically redrawn. The appearance is similar
to a "Screen Saver" feature except the display is completely off. The display is
restored by pressing a key on the keyboard, or clicking the mouse.
USING THE RIGHT POWER CORD :
The accessory power cord for the Northern American region is the wallet plug
with NEMA 5-15 style and is UL listed and CSA labeled. The voltage rating for
the power cord shall be 125 volts AC.
Supplied with units intended for connection to power outlet of personal
computer: Please use a cord set consisting of a minimum No. 18 AWG, type
SJT or SVT three conductors flexible cord. One end terminates with a
grounding type attachment plug, rated 10A, 250V, CEE-22 male configuration.
The other end terminates with a molded-on type connector body, rated 10A,
250V, having standard CEE-22 female configuration.
Please note that power supply cord needs to use VDE 0602, 0625, 0821
approval power cord in European counties.
12
TECHNICAL SUPPORT (FAQ)
Problem & Question
Power LED is not on
Possible Solution
*Check if the Power Switch is in the ON
position
*Power Cord should be connected
*Check if the PC system is Plug & Play
compatible
No Plug & Play
*Check if the Video Card is Plug & Play
compatible
*Check if the D-15 plug pin of Video
Cable is bent
Picture is fuzzy
*Adjust the Contrast and Brightness
Controls.
Picture bounces or a wave *Move electrical devices that may cause
pattern is present in the picture
electrical interference.
The power LED is ON
*Computer Power Switch should be in
(Orange) but there’s no video or nothe ON position.
picture. *Computer Video Card should be snugly
seated in its slot
*Make sure monitor’s video cable is
properly connected to the computer.
*Inspect monitor’s video cable and make
sure none of the pins are bent.
*Make sure computer is operational by
hitting the CAPS LOCK key on the
keyboard while observing the CAPS
LOCK LED. The LED should either
turn ON or OFF after hitting the CAPS
LOCK key.
Missing one of the primary *Inspect the monitor’s video cable and
colors (RED, GREEN, or
BLUE)
make sure that none of the pins are
bent.
13
Screen image is not centered or sized *Adjust pixel frequency (CLOCK) and
properly.
Picture has color defects
(white does not look white)
FOCUS or press hot-key (AUTO)
*Adjust RGB color or select color
temperature
Horizontal or vertical disturbances on *Use win 95/98 shut-down mode
the screen
Adjust CLOCK and FOCUS or
perform hot- key (AUTO-key).
CLOCK (pixel frequency) controls the number of pixels scanned by one
horizontal sweep. If the frequency is not correct, the screen shows vertical
stripes and the picture has not correct width.
FOCUS adjusts the phase of the pixel clock signal. With a wrong phase
adjustment the picture has horizontal disturbances in light picture.
For FOCUS and CLOCK adjustment use “dot-pattern” or win 95/98 shut-down
mode pattern.
14
ERROR MESSAGE & POSSIBLE SOLUTION
CABLE NOT CONNECTED :
1. Check that the signal-cable is properly connected , If the connector is
loose, tighten the connector’s screws.
2. Check the signal -cable connection pins for damage.
INPUT NOT SUPPORT :
Your computer has been set to unsuitable display mode ,set the computer to
display mode given in the following table(See page 18).
15
APPENDIX
SPECIFICATIONS
Driving system TFT Color LCD
LCD Panel
Size
43.2cm(17.0")
Pixel pitch
Brightness
Contrast
0.264mm( H )x 0.264mm( V )
300cd/m2 (Typical)
700:1(Typical)
Viewable angle
150° (H) 135° (V)
Response time 8ms
Video
R,G,B Analog Interface
Digital interface(Only Dual-Input
Model)
30KHz – 80KHz
Input
H-Frequency
V-Frequency
55-75Hz
Display Colors
Dot Clock
16.2M Colors
135MHz
Max. Resolution
Plug & Play
EPA ENERGY STAR® ON Mode
OFF Mode
1280 x 1024 @75Hz
VESA DDC2BTM
≤45W
≤ 2W
Input Connector
D-Sub 15pin
DVI-D 24pin (Only Dual-Input Model)
Analog:0.7Vp-p(standard),
75 OHM, Positive
Digital signal (Only Dual-Input
Model)
Input Video Signal
Maximum Screen Size
Horizontal : 337.92mm
Vertical : 270.34mm
100~264VAC,47~63Hz
Operating Temp: 0° to 40°C
Storage Temp.: -20° to 65°C
Operating Humidity: 10% to 85%
379X400X163.6(W×H×D)mm
4.8kg Unit (net)
Power Source
Environmental
Considerations
Dimensions
Weight (N. W.)
16
Switch
• Auto Adjust Key
• </Volume
• >/ Volume
• Power Button
• MENU
External Controls:
Functions
• Contrast
• Brightness
• Focus
• Clock
• H.Position
• V.Position
• Input signal Selection
(only Dual-Input Model)
• Language
• Auto configuration
(only Analog-input Model)
• (Warm) Color
• (Cool)Color
• RGB Color temperature
• Reset
• OSD position . timeout
• Display information
• Exit
Power Consumption ( Maximum )
Audio Output
Regulatory Compliance
45 Watts
Rated Power 1.5W rms (Per channel)
CUL, FCC, VCCI, CCC, MPR II, CE,
TÜV/GS, TCO’99, UL, ISO13406-2
17
Preset Display Modes
HORIZONTAL
FREQUENCY(kHz) FREQUENCY(Hz)
VERTICAL
VIDEO MODE RESOLUTION
640 × 480
VGA
31.469
37.500
37.879
59.940
75.000
60.317
640 × 480
800 × 600
SVGA
800 × 600
46.875
48.363
56.476
60.023
75.000
1024 × 768
VESA
60.004
70.069
75.029
XGA
1024 × 768
1024 × 768
1280 × 1024
1280 × 1024
64.000
80.000
31.469
48.780
60.241
60.000
75.000
70.087
60.001
74.927
SXGA
DOS
IBM
720 × 400
1024 × 768
1024 × 768
MAC XGA
18
CONNECTOR PIN ASSIGNMENT
1
6
5
10
11
15
15 - Pin Color Display Signal Cable
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1.
2.
3.
4.
5.
6.
7.
8.
Red
Green
Blue
Monitor Ground
DDC-return
R-Ground
G-Ground
B-Ground
9.
10.
11.
12.
13.
14.
15.
+5V
Logic Ground
Monitor Ground
DDC-Serial Data
H-Sync
V-Sync
DDC-Serial Clock
(Dual-Input Model)
Pin
Meaning
Pin
9.
Meaning
Pin
Meaning
1.
2.
TMDS Data2-
TMDS Data2+
TMDS Data1-
17. TMDS Data0-
18. TMDS Data0+
10. TMDS Data1+
TMDS
2/4 Shield
Data
TMDS
1/3 Shield
Data
TMDS Data 0/5
Shield
3.
11.
19.
4.
5.
TMDS Data4-
TMDS Data4+
12. TMDS Data3-
13. TMDS Data3+
20. TMDS Data5-
21. TMDS Data5+
TMDS Clock
Shield
6.
7.
8.
DDC Clock
14. +5V Power
22.
GND(return for
15. +5V
DDC Data
23. TMDS Clock+
hsync.vsync)
Analogue
Vertical Sync
Hot
Detect
Plug
DDC TMDS
Clock-
16.
24.
19
|