IMPORTANT SAFEGUARDS
Table of Contents
IMPORTANT SAFEGUARDS
1 . I n s t a l l a t i o n… … …… … … … …….. . …… …… …… …… . 1
1.1 Package………………………….……….....…………………..… 1
1.2 Precautions-when using this monitor…………………...…..1
1.3 Pedestal ………..………….……………..……………..……...… 1
1.4 How to install/remove the swivel base …..……………..……...… 1
Warnings:
1. Read all of these instructions. Save these instructions for later use, please.
2. Follow all warning and instructions marked on the product.
3. Unplug this monitor from the wall outlet before cleaning. Do not use liquid cleaners
or aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use attachments not recommended by the monitor manufacturer as they may
cause hazards.
5. Do not use this monitor near water. For example near a bathtub, washbowl, kitchen
sink, or laundry tub, in a wet basement, or near a swimming pool, etc.
6. Do not place this monitor on an unstable cart, stand, or table. The monitor may fall,
causing serious injury to a child or adult, and serious damage to the appliance. Use
only with a cart or stand recommended by the manufacturer or sold with monitor.
Wall or shelf mounting should follow the manufacturer's instructions, and should
use a mounting kit approved by the manufacturer.
7. Slots and openings in the cabinet and the back or bottom are provided for ventilation,
and to insure reliable operation of the television receiver and to protect it from
overheating, these openings must not be blocked or covered. The openings should
never be blocked by placing the monitor on a bed, sofa, rug, or other similar surface.
This monitor should never be placed near or over a radiator or heat register. This
monitor should not be placed in built-in installation such as a bookcase unless
proper ventilation is provided.
2. Front control location and functions …………….………………2
2.1 Operation ……………………………………..………...……..… 2
2.2 Adjusting and programming …………………….…….…….….3
2.3 Self test pattern ………………….………………………….…...4
2.4 Safety protection …………….……………..……………………4
2.5 Timing guide ……………………………………..………..……4
3. Technicalinformation ……..………………..……………..….……5
3.1 Products specifications ………………. ………………...……..5
3.2 Signal connector pin assignment …………….…….……...……6
8. This monitor should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supplied in your home,
consult your monitor dealer or local power company.
4.Troubleshooting …………………..………….……………..… 6
9. This monitor is equipped with a three-wire grounding type plug, a plug having a
third (grounding) pin. This plug will only fit into a grounding-type power outlet.
This is a safety feature. If you are unable to insert the plug into the outlet. Contact
your electrician to replace your obsolete outlet. Do not defeat the safety purpose of
the grounding-type plug.
10.Do not allow anything to rest on the power cord. Do not locate this monitor where
the cord will be abused by persons working on it.
11. For added protection for this monitor, when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will prevent damage to the
monitor due to power-line surges.
12. Do not overload wall outlets and extension cords as this can result into fire or
2 Front control locations and functions
PINCUSHION: To adjust the curvature of the sides
TRAPEZOID: To adjust the bottom of the screen to be the same as the top.
PARALLELOGRAM: To adjust the tilt of the side.
2.1 Operation
PIN. BALANCE: To adjust the curvature of the side.
(1) Power ON/OFF Switch ( ): This button is used to turn the monitor on and off.
(2) Power indicator: This indicator lights up green when the monitor operates
normally. If the monitor is in Energy saving mode, this indicator color changes to flash.
(3)To adjust visual settings ( “▼”, “▲”, “MENU”, “EXIT” ): Please following
the procedure of selection and adjusting an item using the OSD system as below steps
for main functions adjustment.
ADVANCED SELECT:
MOIRE ADJUSTMENT: The screen image may shake slightly while
the moire cancellation function is ON. It is normally OFF(H=0,V=0).
V. MOIRE: To adjust the vertical moire of the image.
H. MOIRE: To adjust the horizontal moire of the image.
CORNER: Use to adjust the alignment of top and bottom corner .
TOP CORNER: To adjust the top corner of the image.
BOTTOM CORNER: To adjust the bottom corner of the image.
COLOR SELECT: This control adjusts the color temperature of the screen
image.9300°K and 6500°K are preset by factory. You can not do adjustment.
9300°K: Which is bluish white light.
6500°K: Which is reddish white light.
USER: You can adjust the individual color gun intensity by yourself. Increase
or decrease red, green or blue depending upon which is selected.
OSD ADJUSTMENT:
Step 1: Press and release MENU control key to activate the OSD menu.
Step 2: Press ▲ or ▼ key to highlight the desired option of OSD icon.
Step 3: Press and release MENU key to access the option. The color of the inner area
of the OSD will changed from blue to green.
Step 4: To make your adjustments, press ▲ key to increase or ▼ key to decrease the
setting.
You can choose where you would like OSD image to appear on your screen.
H. POSITION: Moves the OSD image horizontally.
V. POSITION: Moves the OSD image vertically.
TIMER (SEC.):You can select how long the monitor waits after the
last adjust of the knob to shut off the OSD menu. The time setting
choices are from 8 to 60 seconds.
Step 5: Press and release MENU key to store the changed, the color of the inner area
will go back to blue. You can select other function to make adjustments by ▲
and ▼ key. Also you can select EXIT icon or press EXIT key to exit the OSD
menu.
RESET: Reset all settings and back to the factory defaults. If the monitor is
operating in a user mode, this control has no effect.
LANGUAGE: Activates the LANGUAGE submenu. Allow you to choose the
language for the menu screens. Seven languages can be chosen; English,
German, French, Italian, Spanish, Portugal and Chinese.
EXIT: Exits the OSD controls. (Turning off the OSD windows)
DEGAUSS: Eliminates the build-up of stray magnetic fields which alter the
correct scan of the electron beams and affect the purity of the screen colors
focus and convergence. When pressed, your image will jump and waver a bit
as the screen is demagnetized.
2.2 Adjust and Programming
CONTRAST: Adjusts the image brightness in relation to the background.
BRIGHTNESS: Adjusts the overall image and background screen brightness.
H. POSITION: To moves the picture image horizontally left or right.
H. SIZE: To adjust the horizontal size of the image.
V. POSITION: To moves the picture image vertically.
V. SIZE: To adjust the vertical size of the image.
ROTATION: Rotates the entire display clockwise or counter clockwise.
2.3 Self test pattern
3. Technical information
The monitor may display a three colors test pattern. This is to indicate that the
monitor is functioning properly, but the computer’s video signal is not reaching
the monitor. In this case, please make sure the video cable is properly connected.
The test pattern will disappear when the monitor is able to receive the video signal.
However, if the test pattern does not display all three colors (blue, green and red),
the monitor is not functioning properly. Please contact your local dealer for
assistance.
3.1 Products specifications
Picture tube (flat Screen CRT)
Size:
Dot pitch:
17-inch (43.18 cm) diagonal
0.25mm
Tinted screen glass non-glare, black matrix
Surface / transmission:
Maximum viewable area
16.02” (40.69cm) diagonal
310 mm (H) x 230 mm (V)
12.20 inch (H) x 9.06 inch (V) ( Adjustable)
2.4 Safety protection
Display size (factory setting)
The safety protection function is protecting for the monitor itself. When frequency
of video signal from computer’s was out of range, (please refer to monitor
“specifications”) The monitor will protect by itself and a warning message of OSD
will appear on the screen, warning you to resetting monitor type on your computer.
Synchronization range
Horizontal frequency:
Vertical frequency:
30-86KHz
50-160Hz
Max. Resolution
1600x1200
Recommended resolution
Dot Rate
1024x768 /85Hz
150MHz
2.5 Timing guide
This multi-scanning monitor can automatically detect and display several video
modes. If the monitor recognizes one of preset timing signals, it will reset that
mode and any stored display adjustments you have made.
The factory preset modes as indicated in the following table
Power supply (universal)
Input Voltage:
Consumption:
AC 100-240V，60/50 Hz
110 watts maximum.
Video: Analog 0.7Vp -p / 75 Ohms
Sync. : Separate sync. TTL level
Unlimited Number of colors
(depends upon video card)
Input signal
Display Analog Input
Resolution
Resolution
Mode
Fh.
Fv.
Mode
Fh.
Fv.
Weight
Net :
Gross :
(dots x lines)
(dots x lines)
18.5kg (40.7Lb)
21.0kg (46.2Lb)
720 ´ 400
800 ´ 600
31.47
31.47
43.27
46.87
37.88
53.67
70
60
85
75
60
85
63.90
48.36
60.02
68.67
75.01
100
60
75
85
60
1
2
3
4
5
6
7
8
640 ´ 480
640 ´ 480
800 ´ 600
800 ´ 600
800 ´ 600
1024 ´ 768
1024 ´ 768
1024 ´ 768
1600 ´ 1200
Unit dimension (W x H x D)
410 x 412 x 420 (mm)
9
Operating condition
Temperature:
Humidity:
5°C~40°C (41°F to 104°F)
20 ~ 80
10
11
Storage condition
Temperature:
Humidity:
-20°~60°C (-4°F to 140°F)
10 ~ 90
Fh: Horizontal Frequency (KHz)
Fv: Vertical Frequency (Hz)
VESA standard
DDC1/DDC2B (Plug and Play)
NOTE: All technical specifications are subject to change without notice.
Page 4
Page 5
3.2 Signal connector pin assignment
FEDERAL COMMUNICATIONS
COMMISSION(F.C.C)STATEMENT
Pin
1
Assignment
Pin
9
Assignment
No connection
Ground
Red Video
Green Video
Blue Video
Ground
2
10
11
12
13
14
15
This equipment has been tested and found to comply with the limits of a Class B digital
device. Pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
3
Ground
4
SDA For DDC
H. Sync.
5
Ground
6
Red Ground
Green Ground
Blue Ground
V. Sync.
7
SCL For DDC
8
4. Troubleshooting
If your monitor is not performing properly, use the following troubleshooting
for quick solutions to common problems, If the problem persists, call the
dealer. Where you purchased the monitor.
1. Reorient/Relocate the receiving antenna.
No Picture:
2. Increase the separation between the equipment and receiver.
Please check these items
l
l
l
Power cord and signal cable are securely connected.
Monitor in power save mode?
Adjust the brightness and contrast controls.
3. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Display image is too large or small:
Use the function keys to adjust the image.
Picture is scrolling or unstable:
l
CAUTION: Changes or modifications not expressly approved by the manufacturer
responsible for compliance could void the user's authority to operate the
equipment.
l
l
Signal cable should be completely attached to the computer.
Check the signal cable pin assignments incorrect?
Color is abnormal:
l
l
l
Magnetic object nearby?
NOTE: The use of a non-shielded interface cable with this equipment is prohibited.
Signal cable pin assignments incorrect?
Signal cable properly connected?
Image is not correctly shaped:
l
l
A new video mode is selected
User control has not yet been adjusted. Use the function keys to adjust
image.
|