KV8 Pro
AMD AthlonTM 64 System Board
Socket 754
User’s Manual
4200-0405-01
Rev. 1.00
Table Of Contents
Chapter 1. Introduction ..........................................................................1-1
Install CPU and Heatsink.........................................................................2-2
(11). IDE Connectors............................................................................2-15
(14). Status Indicators...........................................................................2-18
Chapter 3. BIOS Setup............................................................................3-1
User’s Manual
3-10. Set Password ..........................................................................................3-26
3-11. Save & Exit Setup..................................................................................3-26
3-12. Exit Without Saving...............................................................................3-26
Appendix A. Install VIA 4-in-1 Driver .................................................................A-1
Appendix B. Install Audio Driver.........................................................................B-1
Appendix C. Install LAN Driver...........................................................................C-1
Appendix D. Install VIA USB 2.0 Driver .............................................................D-1
Appendix F. Install ABIT µGuru Driver..............................................................F-1
Appendix G. POST Code Definition.....................................................................G-1
Appendix I. How to Get Technical Support ......................................................... I-1
KV8 Pro
Introduction
1-1
Chapter 1. Introduction
1-1. Features & Specifications
1. CPU
•
•
Supports 64-bit AMD AthlonTM 64 processor (Socket 754)
1600MHz system bus using HyperTransportTM technology
2. CPU Integrated Memory Controller
•
•
•
72-bit memory controller supports DDR at 266, 333 and 400MHz
Support 2 DIMM DDR 400
Support 2 DIMM up to 2GB Max.
3. Chipset
•
•
•
•
VIA K8T800 Pro + VT8237
Up to 2000MHz HyperTransport
Supports Advanced Configuration and Power Management Interface (ACPI)
Accelerated Graphics Port connector supports AGP 8X/4X (0.8V/1.5V)
4. SATA RAID
•
•
Supports SATA data transfer rates at 150 MB/s (1.5G bps)
Supports SATA RAID 0/1 JBOD
5. Gigabit LAN
•
On board VT6122 10/100/1000 Mb PCI Ethernet Controller
6. Audio
•
•
On board 6-Channel AC 97 CODEC
Professional digital audio interface supports optical S/PDIF Input/Output
7. ABIT Engineered
•
•
•
•
ABIT µGuruTM Technology
ABIT SoftMenuTM Technology
ABIT FanEQTM Technology
CPU ThermalGuardTM Technology
8. Internal I/O Connectors
•
•
•
•
•
1x AGP 8X/4X slot
5x PCI slots
1x floppy port supports up to 2.88MB
2x Ultra DMA 33/66/100/133 connectors
2x Serial ATA 150 connectors
User’s Manual
1-2
Chapter 1
•
•
2x USB headers
1x CD-IN, 1x AUX-IN header
9. Back Panel I/O
•
•
•
•
•
•
1x PS/2 keyboard, 1x PS/2 mouse
1x Serial port connector, 1x Parallel port connector
1x S/PDIF In connector
1x S/PDIF Out connector
5 holes Audio connector (Front Speaker, Line-In, Mic-In, Center/Sub, Surround Speaker)
4x USB, 1x RJ-45 LAN Connector
10. Miscellaneous
•
ATX form factor: 305 x 225 mm
ꢀ
Specifications and information contained herein are subject to change without notice.
KV8 Pro
1-4
Chapter 1
KV8 Pro
Hardware Setup
2-1
Chapter 2. Hardware Setup
Before the Installation: Turn off the power supply switch (fully turn off the +5V standby power), or
disconnect the power cord before installing or unplugging any connectors or add-on cards. Failing to do
so may cause the motherboard components or add-on cards to malfunction or damaged.
2-1. Install The Motherboard
Most computer chassis have a base with many mounting holes to allow motherboard to be securely
attached on and at the same time, prevented from short circuits. There are two ways to attach the
motherboard to the chassis base:
1. use with studs
2. or use with spacers
In principle, the best way to attach the board is to
use with studs. Only if you are unable to do this
should you attach the board with spacers. Line up
the holes on the board with the mounting holes on
the chassis. If the holes line up and there are
screw holes, you can attach the board with studs.
If the holes line up and there are only slots, you
can only attach with spacers. Take the tip of the
spacers and insert them into the slots. After doing
this to all the slots, you can slide the board into
position aligned with slots. After the board has been positioned, check to make sure everything is OK
before putting the chassis back on.
ATTENTION: To prevent shorting the PCB circuit, please REMOVE the metal studs or spacers if they
are already fastened on the chassis base and are without mounting-holes on the motherboard to align with.
User’s Manual
2-2
Chapter 2
2-2. Install CPU and Heatsink
This motherboard provides a ZIF (Zero Insertion
Force) Socket 754 to install AMD Socket 754
CPU. The CPU you bought should contain with a
kit of heatsink, cooling fan, retention frame and
blackplate. If that’s not the case, buy one specially
designed for Socket 754.
Please refer to the figure shown here to install
CPU and heatsink. (For reference only. Your
Heatsink & Fan Assembly may not be exactly the
same as this one.)
1. Locate the Socket 754 on this motherboard.
Pull the CPU release lever sideways to
unlatch and then raise it all the way up.
2. Drop the processor with its pin side down into
the CPU socket. Do not use extra force to
insert CPU; it only fits in one direction. Close
the CPU release lever.
3. Align the Backplate Standoffs with the
mounting holes on motherboard. Position the
backplate onto motherboard.
4. Place the Retention Frame onto the
motherboard and align it with the Backplate
Standoffs.
5. Place heatsink on top of CPU, and make sure
the heatsink fits properly on the retention
frame.
6. Hook both sides of the Spring Clip onto the
Mounting Tabs of Retention Frame. Tighten
screws until the Spring Clip is fully installed.
7. Attach the fan connector of Heatsink & Fan
Assembly with the CPU-FAN connector on
the motherboard.
ATTENTION: Do not forget to set the correct
bus frequency and multiple for your processor.
KV8 Pro
Hardware Setup
2-3
2-3. Install System Memory
This motherboard provides 2 184-pin DDR DIMM slots for memory expansion available from minimum
128MB to maximum 2GB.
Table 2-1. Valid Memory Configurations
Bank
Memory Module
128, 256, 512MB, 1GB
128, 256, 512MB, 1GB
Total Memory
128MB ~ 1GB
128MB ~ 1GB
128MB ~ 2GB
Bank 0, 1 (DIMM1)
Bank 2, 3 (DIMM2)
Total System Memory
NOTE: No hardware or BIOS setup required after adding or removing memory modules.
User’s Manual
2-4
Chapter 2
Power off the computer and unplug the AC power cord before installing or removing memory modules.
1. Locate the DIMM slot on the board.
2. Hold two edges of the DIMM module
carefully, keep away of touching its
connectors.
3. Align the notch key on the module with the
rib on the slot.
4. Firmly press the module into the slots until
the ejector tabs at both sides of the slot
automatically snaps into the mounting notch.
Do not force the DIMM module in with extra
force as the DIMM module only fit in one direction.
5. To remove the DIMM modules, push the two ejector tabs on the slot outward simultaneously, and
then pull out the DIMM module.
ATTENTION: Static electricity can damage the electronic components of the computer or optional
boards. Before starting these procedures, ensure that you are discharged of static electricity by touching a
grounded metal object briefly.
KV8 Pro
Hardware Setup
2-5
2-4. Connectors, Headers and Switches
Here we will show you all of the connectors, headers and switches, and how to connect them. Please read
the entire section for necessary information before attempting to finish all the hardware installation inside
the computer chassis. A complete enlarged layout diagram is shown in Chapter 1 for all the position of
connectors and headers on the board that you may refer to.
WARNING: Always power off the computer and unplug the AC power cord before adding or removing
any peripheral or component. Failing to so may cause severe damage to your motherboard and/or
peripherals. Plug in the AC power cord only after you have carefully checked everything.
(1). ATX Power Input Connectors
This motherboard provides two power connectors to connect to an ATX12V power supply.
NOTE: It is recommended to connect to a power supply with 350W, 20A +5VDC capacity at least for
heavily loaded system, and 2A +5VSB capacity at least for supporting wake-up features.
User’s Manual
2-6
Chapter 2
(2). FAN Connectors
These 3-pin connectors each provide power to the cooling fans installed in your system.
The CPU must be kept cool by using a powerful fan with heatsink. The system is capable of monitoring
the speed of the CPU fan.
•
•
•
•
CPUFAN1: CPU Fan
NBFAN1: Chipset Fan
SYSFAN1: System Fan
AUXFAN1, AUXFAN2: Auxiliary Fan
WARNING: These fan connectors are not jumpers. DO NOT place jumper caps on these connectors.
KV8 Pro
Hardware Setup
2-7
(3). CMOS Memory Clearing Header
This header uses a jumper cap to clear the CMOS memory.
•
•
Pin 1-2 shorted (default): Normal operation.
Pin 2-3 shorted: Clear CMOS memory.
WARNING: Turn the power off first (including the +5V standby power) before clearing the CMOS
memory. Failing to do so may cause your system to work abnormally or malfunction.
User’s Manual
2-8
Chapter 2
(4). Wake-up Header
These headers use a jumper cap to enable/disable the wake-up function.
•
•
USBPWR1:
Pin 1-2 shorted (default): Disable wake-up function support at USB1 port.
Pin 2-3 shorted: Enable wake-up function support at USB1 port.
USBPWR2:
Pin 1-2 shorted (default): Disable wake-up function support at USB2 port.
Pin 2-3 shorted: Enable wake-up function support at USB2 port.
KV8 Pro
Hardware Setup
2-9
(5). Front Panel Switches & Indicators Headers
This header is used for connecting switches and LED indicators on the chassis front panel.
Watch the power LED pin position and orientation. The mark “+” align to the pin in the figure below
stands for positive polarity for the LED connection. Please pay attention to connect these headers. A
wrong orientation will only cause the LED not lighting, but a wrong connection of the switches could
cause system malfunction.
•
•
•
•
•
•
HLED (Pin 1, 3):
Connects to the HDD LED cable of chassis front panel.
RST (Pin 5, 7):
Connects to the Reset Switch cable of chassis front panel.
SPK (Pin 15, 17, 19, 21):
Connects to the System Speaker cable of chassis.
SLED (Pin 2, 4):
Connects to the Suspend LED cable (if there is one) of chassis front panel.
PWR-ON (Pin 6, 8):
Connects to the Power Switch cable of chassis front panel.
PLED (Pin 16, 18, 20):
Connects to the Power LED cable of chassis front panel.
User’s Manual
Hardware Setup
2-11
(7). Front Panel Audio Connection Header
This header provides the connection to audio connector at front panel.
•
To use the audio connector at front panel, remove all the jumpers on this header, and then connect
to front panel by the extension cable provided with the chassis.
•
To use the audio connector at rear panel, disconnect the extension cable, attach the jumpers back at
pin 5-6, and pin 9-10 (default setting).
Pin
1
Pin Assignment
Audio Mic.
Pin
2
Pin Assignment
Ground
3
Audio Mic. Bias
4
VCC
Speaker Out Right
Channel
Speaker Out Right
Channel Return
5
7
9
6
8
X
NC
Speaker Out Left
Channel
Speaker Out Left
Channel Return
10
11 Ground
13 VCC
12 S/PDIF In
14 S/PDIF Out
User’s Manual
Hardware Setup
2-13
(9). Accelerated Graphics Port Slot
This slot supports an optional AGP graphics card up to AGP 8X mode. Please refer to our Web site for
more information on graphics cards.
ATTENTION: This motherboard does not support 3.3V AGP cards. Use only 1.5V or 0.8V AGP cards.
User’s Manual
2-14
Chapter 2
(10). Floppy Disk Drive Connector
This connector supports two standard floppy disk drives via a 34-pin 34-conductor ribbon cable.
Connecting the Floppy Disk Drive Cable:
1. Install one end of the ribbon cable into the FDC1 connector. The colored edge of the ribbon cable
should be aligned with pin-1 of FDC1 connector.
2. Install the other end(s) of ribbon cable into the disk drive connector(s). The colored edge of the
ribbon cable should be also aligned with pin-1 of disk drive connector. The endmost connector
should be attached to the drive designated as Drive A.
KV8 Pro
Hardware Setup
2-15
(11). IDE Connectors
This motherboard provides two IDE ports to connect up to four IDE drives at Ultra DMA mode by Ultra
ATA/66 ribbon cables. Each cable has 40-pin 80-conductor and three connectors, providing two hard
drives connection with motherboard. Connect the single end (blue connector) at the longer length of
ribbon cable to the IDE port on motherboard, and the other two ends (gray and black connector) at the
shorter length of the ribbon cable to the connectors on hard drives.
If you want to connect two hard drives together through one IDE channel, you must configure the second
drive to Slave mode after the first Master drive. Please refer to the drives’ documentation for jumper
settings. The first drive connected to IDE1 is usually referred to as “Primary Master”, and the second
drive as “Primary Slave”. The first drive connected to IDE2 is referred to as “Secondary Master” and the
second drive as “Secondary Slave”.
Keep away from connecting one legacy slow speed drive, like CD-ROM, together with another hard drive
on the same IDE channel; this will drop your integral system performance.
User’s Manual
2-16
Chapter 2
(12). POST Code Display
This is an LED device to display the “POST” Code, the acronym of Power On Self Test. The computer
will execute the POST action whenever you power on the computer. The POST process is controlled by
the BIOS. It is used to detect the status of the computer’s main components and peripherals. Each POST
Code corresponds to different checkpoints that are also defined by the BIOS in advance. For example,
“memory presence test” is an important checkpoint and its POST Code is “C1”. When the BIOS execute
any POST item, it will write the corresponding POST Code into the address 80h. If the POST passes, the
BIOS will process the next POST item and write the next POST Code into the address 80h. If the POST
fails, we can check the POST Code in address 80h to find out where the problem lies.
This LED device also displays the “POST” Code of AC2003, an “uGuru” chipset developed exclusively
by ABIT computer.
NOTE: The decimal point lights up when executing the AC2003 POST action.
See Appendix for both AWARD and AC2003 POST Code definition.
KV8 Pro
Hardware Setup
2-19
(15). System Management Bus Headers
This header is reserved for system management bus (SM bus). The SM bus is a specific implementation
of an I2C bus. I2C is a multi-master bus, which means that multiple chips can be connected to the same
bus and each one can act as a master by initiating a data transfer. If more than one master simultaneously
tries to control the bus, an arbitration procedure decides which master gets priority.
User’s Manual
2-20
Chapter 2
(16). Back Panel Connectors
•
•
•
•
Mouse: Connects to PS/2 mouse.
Keyboard: Connects to PS/2 keyboard.
LPT1: Connects to printer or other devices that support this communication protocol.
COM1: Connects to external modem, mouse or other devices that support this communication
protocol.
•
•
•
OPTIN1: This connector provides an S/PDIF in connection through optical fiber to digital
multimedia devices.
OPTOUT1: This connector provides an S/PDIF out connection through optical fiber to digital
multimedia devices.
AUDIO1:
R.L./R.R. (Rear Left / Rear Right): Connects to the rear left and rear right channel in the 5.1
channel audio system.
Cen./Sub. (Center / Subwoofer): Connects to the center and subwoofer channel in the 5.1
channel audio system.
•
AUDIO2:
Mic In: Connects to the plug from external microphone.
Line In: Connects to the line out from external audio sources.
F.L./F.R. (Front Left / Front Right): Connects to the front left and front right channel in the
5.1-channel or regular 2-channel audio system.
•
•
LAN: Connects to Local Area Network.
USB1/USB2: Connects to USB devices such as scanner, digital speakers, monitor, mouse,
keyboard, hub, digital camera, joystick etc.
KV8 Pro
BIOS Setup
3-1
Chapter 3. BIOS Setup
This motherboard provides a programmable EEPROM that you can update the BIOS utility. The BIOS
(Basic Input/Output System) is a program that deals with the basic level of communication between
processor and peripherals. Use the BIOS Setup program only when installing motherboard, reconfiguring
system, or prompted to “Run Setup”. This chapter explains the Setup Utility of BIOS utility.
After powering up the system, the BIOS message appears on the screen, the memory count begins, and
then the following message appears on the screen:
PRESS DEL TO ENTER SETUP
If this message disappears before you respond, restart the system by pressing <Ctrl> + <Alt> + <Del>
keys, or by pressing the Reset button on computer chassis. Only when it failed by these two methods can
you restart the system by powering it off and then back on.
After pressing <Del> key, the main menu screen appears.
NOTE: In order to increase system stability and performance, our engineering staffs are constantly
improving the BIOS menu. The BIOS setup screens and descriptions illustrated in this manual are for
your reference only, may not completely match what you see on your screen.
In the BIOS Setup main menu, you can see several options. We will explain these options step by step in
the following pages of this chapter, but let us first see a short description of the function keys you may
use here.
Esc:
Press this button to quit the BIOS Setup.
↑↓← →:
Press these buttons to choose, in the main menu, the option you want to confirm or to modify.
F10:
When you have completed the setup of BIOS parameters, press this button to save these parameters and
to exit the BIOS Setup menu.
User’s Manual
3-2
Chapter 3
F6:
You may create a profile to save the new BIOS settings in it. Press <F6> button in the main menu, a
dialog box with five numbers (1~5) will appear on the screen. Select one number, and press <Enter>.
Then, you will get a confirmation dialog box with a message similar to:
Save Profile To BIOS (Y/N)?
After pressing “Y”, the following message will appear to assist you in creating a name for the profile.
Enter Profile Name:
Type the profile name, and press <Enter>. The new BIOS settings now are saved to the selected profile.
NOTE: You may save up to five profiles to BIOS.
F7:
Press <F7> button in the main menu, a dialog box with five numbers (1~5) will appear on the screen.
Select the profile you want, and press <Enter>. Then, you will get a confirmation dialog box with a
message similar to:
Load Profile From BIOS (Y/N)?
Press “Y” to load the BIOS settings in this profile.
KV8 Pro
BIOS Setup
3-3
3-1. µGuru Utility
Brand Name:
This item displays the CPU model name, for example: AMD AthlonTM 64 processor 3200+.
Frequency:
This item displays the processor speed.
CPU Operating Speed:
This item displays the CPU operating speed according to the type and speed of your CPU. You can also
select the [User Define] option to enter the manual option.
User Define:
WARNING: The wrong settings of the multiplier and external clock in certain circumstances may cause
CPU damage. Setting the working frequency higher than the PCI chipset or processor specs, may cause
abnormal memory module functioning, system hangs, hard disk drive data lose, abnormal functioning of
the VGA card, or abnormal functioning with other add-on cards. Using non-specification settings for your
CPU is not the intention of this explanation. These should be used for engineering testing, not for normal
applications.
There will be no guaranty for the settings beyond specification, any damage of any component on this
motherboard or peripherals result therein is not our responsibility.
ꢀ
External Clock:
This item selects the external clock frequency. Due to the specification limit of the CPU you installed, the
speed you set over its standard bus speed is supported, but not guaranteed.
ꢀ
Multiplier Factor:
This item displays the multiplier factor for the CPU you installed.
NOTE: Some processors might have this multiplier factor locked, so there is no way to choose a higher
multiplier factor.
User’s Manual
3-4
Chapter 3
Voltages Control:
This option allows you to switch between the default and user-defined voltages. Leave this setting to
default unless the current voltage setting cannot be detected or is not correct. The option “User Define”
enables you to select the following voltages manually.
ꢀ
CPU Core Voltage:
This item selects the CPU core voltage.
AGP VDDQ Voltage:
This item selects the voltage for AGP slot.
DDR SDRAM Voltage:
This item selects the voltage for DRAM slot.
NB Voltage:
This item selects the NB voltage.
SB Voltage:
This item selects the SB voltage.
HyperTransport Voltage:
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
This item selects the voltage for LDT Bus.
<F8> function key:
After a new configuration on items “External Clock” and “Voltage”, pressing <F8> button now in this
menu will make it become effective immediately.
ATTENTION: An external clock too much over its specification may cause the system unstable or even
fail, please proceed with highly attention.
Power Cycle Statistics:
Click <Enter> key to enter its submenu:
These items display the power cycle statistics for each element.
KV8 Pro
BIOS Setup
3-5
ꢀ
Back to µGuru Utility Setup Menu:
Use<→> key to switch from OC Guru setup menu to ABIT EQ setup menu:
ABIT EQ Beep Control:
This item allows you to enable or disable ABIT EQ Beep Control function.
ꢀ
Temperature Monitoring:
Click <Enter> key to enter its submenu:
CPU Temperature/System Temperature/PWM Temperature:
These items display the temperature of CPU, System, and Power Module.
ꢀ
Shutdown Enable:
Use <Space> key to enable system shutdown function. If the CPU/System/PWM’s temperature exceeds
the shutdown temperature limit, the system would shutdown automatically.
User’s Manual
3-6
Chapter 3
ꢀ
Shutdown Temp.:
This items sets the temperature that would shutdown the system automatically in order to prevent system
overheats.
ꢀ
Beep Enable:
Use <Space> key to enable warning beeps function. Once the system has detected that the
CPU/System/PWM’s temperature exceeded the beep temperature limit, warning beeps will sound.
ꢀ
Beep Temp.:
This item selects the warning temperature limit.
NOTE: The shutdown temperature must be set above the warning temperature.
ꢀ
Voltage Monitoring:
Click <Enter> key to enter its submenu:
All Voltages:
These items display the voltage of each element.
ꢀ
Shutdown Enable:
Use <Space> key to enable system shutdown function. If the voltage of corresponding element is
higher/lower than the high/low limit, the system would automatically shutdown.
ꢀ
Beep Enable:
Use <Space> key to enable warning beeps function. If the voltage of corresponding element is
higher/lower than the high/low limit, warning beeps will sound.
ꢀ
High/Low Limit:
These items set the high and low voltage limit.
NOTE: The value of high limit must be set above the one of low limit.
KV8 Pro
BIOS Setup
3-7
ꢀ
Fan Speed Monitoring:
Click <Enter> key to enter its submenu:
CPU/NB/SYS/AUX1/AUX2 FAN Speed:
These items display the speed of the fans connected to CPU, NB, SYS, AUX1 and AUX2 FAN headers.
Shutdown Enable:
ꢀ
Use <Space> key to enable system shutdown function. Once the system has detected that the fan speed is
lower than the low limit value, system will shutdown automatically.
ꢀ
Beep Enable:
Use <Space> key to enable warning beeps function. If the fan speed is lower than the low limit value,
warning beeps will sound.
ꢀ
Low Limit:
These items set the low limit of fan speed.
NOTE: Only the fans with 3-pin plugs provide the speed monitoring function.
User’s Manual
3-8
Chapter 3
ꢀ
FanEQ Control:
Click <Enter> key to enter its submenu:
CPU/NB/SYS FanEQ Control:
When set to [Enabled], these items allow you to control the CPU/NB/System fan speed by its setting
combination of temperature and voltage high/low limit.
ꢀ
Reference Temperature:
These items display the CPU/NB/System temperature.
Control Temp. High/Low:
These items set the high and low temperature limit that you want to do the fan speed control.
DC Fan Voltage High/Low:
ꢀ
ꢀ
These items set the high and low voltage limit that you want to provide the fan with.
NOTE: The value of high limit must be set above the one of low limit.
KV8 Pro
BIOS Setup
3-9
3-2. Standard CMOS Features
This section contains the basic configuration parameters of the BIOS. These parameters include date,
hour, VGA card, FDD and HDD settings.
Date (mm:dd:yy):
This item sets the date you specify (usually the current date) in the format of [Month], [Date], and [Year].
Time (hh:mm:ss):
This item sets the time you specify (usually the current time) in the format of [Hour], [Minute], and
[Second].
IDE Channel 1 Master / Slave, IDE Channel 2 Master / Slave:
Click <Enter> key to enter its submenu:
IDE HDD Auto-Detection:
This item allows you to detect the parameters of IDE drives by pressing <Enter> key. The parameters will
be shown on the screen automatically.
User’s Manual
3-10
Chapter 3
IDE Channel 1 Master / Slave, IDE Channel 2 Master / Slave:
When set to [Auto], the BIOS will automatically check what kind of IDE drive you are using. If you want
to define your own drive by yourself, set it to [Manual] and make sure you fully understand the meaning
of the parameters. Please refer to the instruction manual provided by the device’s manufacturer to get the
setting right.
Access Mode:
This item selects the mode to access your IDE devices. Leave this item to its default [Auto] setting to
detect the access mode of your HDD automatically.
Capacity:
This item displays the approximate capacity of the disk drive. Usually the size is slightly greater than the
size of a formatted disk given by a disk-checking program.
Cylinder:
This item configures the numbers of cylinders.
Head:
This item configures the numbers of read/write heads.
Precomp:
This item displays the number of cylinders at which to change the write timing.
Landing Zone:
This item displays the number of cylinders specified as the landing zone for the read/write heads.
Sector:
This item configures the numbers of sectors per track.
ꢀ
Back to Standard CMOS Features Setup Menu:
Drive A & Drive B:
This item sets the type of floppy drives (usually only Drive A) installed.
Floppy 3 Mode Support:
This item allows you to use “3 Mode Floppy Drive” in Japanese computer system by selecting drive A, B,
or both. Leave this item to its default [Disabled] setting if you are not using this Japanese standard floppy
drive.
Video:
This item selects the type of video adapter used for the primary system monitor.
KV8 Pro
BIOS Setup
3-11
[EGA/VGA]: (Enhanced Graphics Adapter/Video Graphics Array) For EGA, VGA, SVGA and PGA
monitor adapters.
[CGA 40]: (Color Graphics Adapter) Power up in 40-column mode.
[CGA 80]: (Color Graphics Adapter) Power up in 80-column mode.
[Mono]: (Monochrome adapter) Includes high-resolution monochrome adapters.
Halt On:
This item determines whether the system stops if an error is detected during system boot-up.
[All Errors]: The system-boot will stop whenever the BIOS detect a non-fatal error.
[No Errors]: The system-boot will not stop for any error detected.
[All, But Keyboard]: The system-boot will stop for all errors except a keyboard error.
[All, But Diskette]: The system-boot will stop for all errors except a diskette error.
[All, But Disk/Key]: The system-boot will stop for all errors except a diskette or keyboard error.
Base Memory:
This item displays the amount of base memory installed in the system. The value of the base memory is
typically 640K for system with 640K or more memory size installed on the motherboard.
Extended Memory:
This item displays the amount of extended memory detected during system boot-up.
Total Memory:
This item displays the total memory available in the system.
User’s Manual
3-12
Chapter 3
3-3. Advanced BIOS Features
Hard Disk Boot Priority:
This item selects the hard disks booting priority. By pressing <Enter> key, you can enter its submenu
where the hard disks detected can be selected for the booting sequence to boot up system.
This item functions only when there is the option of [Hard Disk] in any one of the First/Second/Third
Boot Device items.
ꢀ
Bootable Add-in Device:
This item allows you to select the add-in device priority between [PCI Slot Device] and [Onchip SATA
RAID]. Onchip SATA RAID means VIA SATA RAID.
First Boot Device / Second Boot Device / Third Boot Device / Boot Other Device:
Select the drive to boot first, second and third in the [First Boot Device], [Second Boot Device], and
[Third Boot Device] items respectively. The BIOS will boot the operating system according to the
sequence of the drive selected. Set [Boot Other Device] to [Enabled] if you wish to boot from another
device other than these three items.
Swap Floppy Drive:
When set to [Enabled], and the system is booting from the floppy drive, the system will boot from drive B
instead of the regular drive A. There must be two floppy drives connected in the system to use this
function.
Boot Up NumLock Status:
This item determines the default state of the numeric keypad at system booting up.
[On]: The numeric keypad functions as number keys.
[Off]: The numeric keypad functions as arrow keys.
Security Option:
This item determines when the system will prompt for password - every time the system boots or only
when enters the BIOS setup.
KV8 Pro
BIOS Setup
3-13
[Setup]: The password is required only when accessing the BIOS Setup.
[System]: The password is required each time the computer boots up.
NOTE: Don’t forget your password. If you forget the password, you will have to open the computer case
and clear all information in the CMOS before you can start up the system. But by doing this, you will
have to reset all previously set options.
MPS Version Ctrl For OS:
This item specifies which version of MPS (Multi-Processor Specification) this motherboard will use. The
options are 1.1 and 1.4. The default setting is 1.4. If you use an older OS for dual processor executing,
please set this option to 1.1.
Report No FDD For OS:
When set to [Enabled], this item allows you to run some older operating system without floppy disk drive.
Leave this item to its default setting.
Delay IDE Initial (Secs):
This item allows the BIOS to support some old or special IDE devices by prolonging this delay time. A
larger value will give more delay time to the device for which to initialize and to prepare for activation.
Full Screen LOGO Show:
This item determines to show the full screen logo when booting.
Disable unused PCI Clock:
This option disables the clock of PCI slot that is not in use.
[Enabled]: The system automatically detect the unused PCI slots, and stop sending clock signal to these
unused PCI slots.
[Disabled]: The system always send clock signal to all PCI slots.
NOTE: Set this option to [Disabled] setting if there are adapters that cannot be automatically detected by
the system and will cause malfunction.
User’s Manual
3-14
Chapter 3
3-4. Advanced Chipset Features
AGP & P2P Bridge Control:
Click <Enter> key to enter its submenu:
AGP Aperture Size:
This option specifies the amount of system memory that can be used by the AGP device. The aperture is a
portion of the PCI memory address range dedicated for graphics memory address space.
AGP 2.0 Mode:
This item selects the data transfer rate of AGP device. A higher rate delivers faster and better graphics to
your system. Make sure your graphics card supports the mode you select.
AGP Driving Control:
Leave this item to its default setting.
ꢀ
AGP Driving Value:
Leave this item to its default setting.
KV8 Pro
BIOS Setup
3-15
AGP Fast Write:
Two options are available: Disabled ꢀ Enabled. The default setting is Enabled. If your AGP adapter can
support this function, then you can choose Enabled. Otherwise, choose Disabled.
AGP Master 1 WS Write:
Two options are available: Disabled ꢀ Enabled. The default setting is Disabled. This implements a
single delay when writing to the AGP Bus. When you set it to Enabled, two-wait states are used by the
system, allowing for greater stability.
AGP Master 1 WS Read:
Two options are available: Disabled ꢀ Enabled. The default setting is Disabled. This implements a
single delay when reading to the AGP Bus. When you set it to Enabled, two-wait states are used by the
system, allowing for greater stability.
AGP 3.0 Calibration cycle:
Leave this item to its default setting.
DBI Output for AGP Trans.:
Leave this item to its default setting.
ꢀ
Back to Advanced Chipset Features Setup Menu:
DRAM Configuration:
Click <Enter> key to enter its submenu:
Current FSB Frequency:
This item will show you the current system front side bus speed.
Current DRAM Frequency:
This item will show you the current DRAM bus speed.
User’s Manual
3-16
Chapter 3
DRAM Timing Selectable:
Two options are available: Manual ꢀ By SPD. The default setting is By SPD. When set to “By SPD”, the
BIOS will read the DRAM module SPD data and automatically set to the values stored in it.
ꢀ
DRAM Clock:
This item sets the DRAM clock of your DRAM module. The system may be unstable or unable to boot up
if your DRAM module does not support the clock you set.
When set to [By SPD], the BIOS will read the DRAM module SPD data and automatically set the DRAM
clock by the value stored in it.
ꢀ
CAS Latency Time:
Three options are available: 2 ꢀ 2.5 ꢀ 3. The default setting is 2.5. You can select SDRAM CAS
(Column Address Strobe) latency time according your SDRAM specification.
ꢀ
RAS# to CAS# Delay:
This item specifies the RAS# active to CAS# read write delay time to the same bank.
Min. RAS# Active Time:
This item specifies the minimum RAS# active time.
RAS# Precharge Time:
This item specifies the RAS# precharge time.
Row Cycle Time:
This item specifies the RAS# active to RAS# active time or auto refresh time of the same bank.
Row Refresh Cycle Time:
This item specifies the auto refresh active to RAS# active time or RAS# auto refresh time.
RAS# to RAS# Delay:
This item specifies the RAS# active to RAS# active delay time of different bank.
Write Recovery Time:
This item specifies the time measured from the last write datum is safely registered by the DRAM.
Write to Read Delay:
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
This item specifies the time measured from the rising edge following the last non-masked data strobe to
the rising edge of the next read command.
ꢀ
Read to Write Delay:
This item specifies the read to write delay.
KV8 Pro
BIOS Setup
3-17
ꢀ
Back to Advanced Chipset Features Setup Menu:
LDT & PCI Bus Control:
Click <Enter> key to enter its submenu:
Upstream/Downstream LDT Bus Width:
This item allows you to select LDT Bus Width.
LDT Bus Frequency:
This item allows you to select LDT Bus Frequency.
PCI1/PCI2 Master 0 WS Write:
Two options are available: Enabled or Disabled. The default setting is Enabled. When Enabled, writes to
the PCI bus are executed with zero wait state (immediately) when PCI bus is ready to receive data. If it is
set to Disabled, the system will wait one state before data is written to the PCI bus.
PCI1/PCI2 Post Write:
Two options are available: Enabled or Disabled. The default is Enabled, When Enable, data transmission
from CPU to PCI bus are buffered and compensate for the different speed between CPU and PCI bus. If it
is set to Disabled, data transmissions are not buffered and CPU must wait until the data transmission is
complete and then start another transmission cycle.
ꢀ
Back to Advanced Chipset Features Setup Menu:
Memory Hole:
When set to [15M–16M], the memory address space at 15M-16M will be reserved for ISA expansion
cards that specifically requires this setting. This makes the memory from 15MB and up unavailable to the
system. Leave this item to its default setting.
Vlink Data Rate:
This item can let you select the Vlink Data Rate between northbridge and southbridge.
User’s Manual
3-18
Chapter 3
3-5. Integrated Peripherals
OnChip IDE Device:
Click <Enter> key to enter its submenu:
SATA RAID ROM:
This item allows you to use the boot ROM of on-chip Serial ATA RAID to boot-up system.
IDE Bus Master:
This option enables or disables the IDE bus mastering capability under the DOS environment.
Onboard IDE-1/IDE-2 Controller:
This item allows you to enable or disable the primary and secondary IDE controller. Select [Disabled] if
you want to add a different hard drive controller.
IDE Prefetch Mode:
Two options are available: Disabled or Enabled. The default setting is Enabled. The onboard IDE drive
interfaces supports IDE prefetching for faster drive accesses. If you install a primary and/or secondary
add-in IDE interface, set this field to Disabled if the interface does not support prefetching.
KV8 Pro
BIOS Setup
3-19
ꢀ
Back to Integrated Peripherals Setup Menu:
OnChip PCI Device:
Click <Enter> key to enter its submenu:
OnChip Audio Controller:
This option enables or disables the audio controller.
Onboard LAN Controller:
This option enables or disables the LAN controller.
ꢀ
LAN Boot ROM:
This item enables or disables the Boot ROM on LAN controller.
OnChip USB Controller:
This option enables or disables the USB controller.
ꢀ
USB 2.0 Controller:
This option enables or disables the USB 2.0 controller.
USB Keyboard Support:
ꢀ
This item allows you to select [BIOS] for using USB keyboard in DOS environment, or [OS] in OS
environment.
ꢀ
USB Mouse Support:
This item allows you to select [BIOS] for using USB mouse in DOS environment, or [OS] in OS
environment.
User’s Manual
3-20
Chapter 3
ꢀ
Back to Integrated Peripherals Setup Menu:
SuperIO Device:
Click <Enter> key to enter its submenu:
Onboard FDD Controller:
Two options are available: Enabled and Disabled. The default setting is Enabled. You can enable or
disable the onboard FDD controller.
Onboard Serial Port 1:
This is used to specify the I/O address and IRQ of Serial Port 1. Six options are available: Disabled ꢀ
3F8/IRQ4 ꢀ 2F8/IRQ3 ꢀ 3E8/IRQ4 ꢀ 2E8/IRQ3 ꢀ AUTO. The default setting is 3F8/IRQ4.
Onboard Parallel Port:
Sets the I/O address and IRQ of the onboard parallel port. Four options are available: Disabled ꢀ
378/IRQ7 ꢀ 278/IRQ5 ꢀ 3BC/IRQ7. Default setting is 378/IRQ7.
ꢀ
Parallel1 Port Mode:
Four options are available: SPP ꢀ EPP ꢀ ECP ꢀ ECP+EPP.
EPP Mode Select:
ꢀ
Two options are available: EPP1.7 ꢀ EPP1.9. When the mode selected for the parallel port mode is EPP,
the two EPP version options are available.
ꢀ
ECP Mode Use DMA:
Two options are available: 1 ꢀ 3. The default setting is 3. When the mode selected for the parallel port
mode is ECP, the DMA channel selected can be Channel 1 or Channel 3.
ꢀ
Back to Integrated Peripherals Setup Menu:
Init Display First:
This item selects to initialize AGP or PCI Slot first when the system boots.
[PCI Slot]: When the system boots, it will first initialize PCI.
[AGP]: When the system boots, it will first initialize AGP.
KV8 Pro
BIOS Setup
3-21
3-6. Power Management Setup
ACPI Suspend Type:
This item selects the type of Suspend mode.
[S1(PowerOn-Suspend)]: Enables the Power On Suspend function.
[S3(Suspend-To-RAM)]: Enables the Suspend to RAM function.
ꢀ
Run VGABIOS if S3 Resume:
Three options are available: Auto ꢀ Yes ꢀ No. The default setting is Auto. This item can let you choose
when S3 resume active, the VGA BIOS need to be initiative or not.
ꢀ
Resume by OnChip USB:
Two options are available: Disabled or Enabled. The default setting is Disabled. When set to Enabled,
any event affecting from onchip USB will awaken a system that has powered down. This item can be
configured only if the item “ACPI Suspend Type” is set to [S3(STR)].
Power Button Function:
This item selects the method of powering off your system:
[Delay 4 Sec.]: Pushing the power button for more than 4 seconds will power off the system. This will
prevent the system from powering off in case you accidentally hit or pushed the power button.
[Instant-Off]: Pressing and then releasing the power button at once will immediately power off the
system.
CPU THRM-Throttling:
This item controls the CPU speed by cutting down its regular power to a percentage during the STR
(Suspend To RAM) state.
Restore On AC Power Loss:
This item selects the system action after an AC power failure.
User’s Manual
3-22
Chapter 3
[Power Off]: When power returns after an AC power failure, the system’s power remains off. You must
press the Power button to power-on the system.
[Power On]: When power returns after an AC power failure, the system’s power will be powered on
automatically.
[Last State]: When power returns after an AC power failure, the system will return to the state where you
left off before power failure occurs. If the system’s power is off when AC power failure occurs, it will
remain off when power returns. If the system’s power is on when AC power failure occurs, the system
will power-on when power returns.
Wakeup by PME# of PCI:
Two options are available: Disabled or Enabled. The default setting is Disabled. When set to Enabled,
any event affecting from PCI card (PME) will awaken a system that has powered down.
Resume by Ring:
Two options are available: Disabled or Enabled. The default setting is Disabled. When set to Enabled,
any event affecting from Modem Ring will awaken a system that has powered down.
Wakeup by Alarm:
Two options are available: Disabled or Enabled. The default setting is Disabled. When set to Enabled,
you can set the date and time at which the RTC (real-time clock) alarm awakens the system from Suspend
mode.
ꢀ
Date (of Month) Alarm / Resume Time (hh:mm:ss):
You can set the Date (month) Alarm and Time Alarm (hh:mm:ss). Any event occurring will awaken a
system that has powered down.
Cool’n’Quiet Technology:
This option enables or disables the AMD K8 cool and quiet function.
POWER ON Function:
This item selects the way you want your system to power on.
[Password]: Use a password to power on the system, select this option then press <Enter>. Enter your
password. You can enter up to 5 characters. Type in exactly the same password to confirm, and then press
<Enter>.
[Hot KEY]: Use any of the function keys between <F1> to <F12> to power on the system.
[Mouse Left]: Double click the mouse left button to power on the system.
[Mouse Right]: Double click the mouse right button to power on the system.
[Any KEY]: Use any keyboard keys to power on the system.
[BUTTON ONLY]: Use only the power button to power on the system.
[Keyboard 98]: Use the power-on button on the “Keyboard 98” compatible keyboard to power on the
system.
KV8 Pro
BIOS Setup
3-23
NOTE: To enable this “Power On” function, the wake-up header of [USBPWR1] and [USBPWR2] must
be set to [Enabled] position. Please refer to the configuration of “Wake-up Header” [USBPWR1] and
[USBPWR2] in section 2-4, chapter 2.
The mouse wake up function can only be used with the PS/2 mouse, not with the COM port or USB type.
Some PS/2 mice cannot wake up the system because of compatible problems. If the specs of your
keyboard are too old, it may fail to power on.
ꢀ
KB Power ON Password:
This item sets the password required in order to power on your computer.
NOTE: Do not forget your password, or you will have to clear the CMOS and reset all parameters in
order to utilize this function again.
ꢀ
Hot Key Power ON:
This item powers on the system by pressing <Ctrl> key plus one of each function key (<F1> ~ <F12>)
simultaneously.
User’s Manual
3-24
Chapter 3
3-7. PnP/PCI Configurations
Resources Controlled By:
This item configures all of the boot and Plug-and-Play compatible devices.
[Auto(ESCD)]: The system will automatically detect the settings.
[Manual]: Choose the specific IRQ resources in the “IRQ Resources” menu.
ꢀ
IRQ Resources:
Click <Enter> key to enter its submenu:
This item sets each system interrupt to either [PCI Device] or [Reserved].
ꢀ
Back to PnP/PCI Configurations Setup Menu:
PCI/VGA Palette Snoop:
This item determines whether the MPEG ISA/VESA VGA cards can work with PCI/VGA or not.
[Enabled]: MPEG ISA/VESA VGA cards work with PCI/VGA.
[Disabled]: MPEG ISA/VESA VGA cards do not work with PCI/VGA.
KV8 Pro
BIOS Setup
3-25
PIRQ_0 Use IRQ No. ~ PIRQ_7 Use IRQ No.:
This item specifies the IRQ number manually or automatically for the devices installed on PCI slots.
For the relations between the hardware layout of PIRQ (the signals from the VIA VT8237 chipset), INT#
(means PCI slot IRQ signals) and devices, please refer to the table below:
Signals
AGP
LAN PCI-1 PCI-2 PCI-3 PCI-4 PCI-5 SATA
INT A INT D INT C INT B
INT B INT A INT D INT C
INT C INT B INT A INT D
INT D INT C INT B INT A
INT A
PIRQ_0 Assignment INT A
PIRQ_1 Assignment INT B
PIRQ_2 Assignment
PIRQ_3 Assignment
PIRQ_4 Assignment
PIRQ_5 Assignment
INT B INT A
PIRQ_6 Assignment
INT A
INT C
INT D
PIRQ_7 Assignment
NOTE:
•
•
PCI slot 1 shares IRQ signals with AGP slot.
If you want to install two PCI cards into those PCI slots that share IRQ with one another at the same
time, you must make sure that your OS and PCI devices’ driver supports the IRQ sharing function.
User’s Manual
3-26
Chapter 3
3-8. Load Fail-Safe Defaults
This option loads the BIOS default values for the most stable, minimal-performance system operations.
3-9. Load Optimized Defaults
This option loads the BIOS default values that are factory settings for optimal-performance system
operations.
3-10. Set Password
This option protects the BIOS configuration or restricts access to the computer itself.
3-11. Save & Exit Setup
This option saves your selections and exits the BIOS setup menu.
3-12. Exit Without Saving
This option exits the BIOS setup menu without saving any change.
KV8 Pro
Install VIA 4-in-1 Driver
A-1
Appendix A. Install VIA 4-in-1 Driver
NOTE: Please install this VIA 4-in-1 driver first after having installed the Windows operating system.
The installation procedures and screen shots in
this section are based on Windows XP operating
system. For those of other OS, please follow its
on-screen instruction.
Insert the Driver & Utility CD into CD-ROM
drive, it should execute the installation program
automatically. If not, double-click the execution
file at the main directory of this CD to enter the
installation menu.
After entering the installation menu, move your
curser to [Drivers] tab. Click [VIA 4in1 Driver].
The following screen appears.
3. Click [Next].
1. Click [Next].
4. Click [Next].
2. Click [Yes].
5. Click [Next].
User’s Manual
A-2
Appendix A
6. Click [Next].
7. Choose [Yes, I want to restart my computer
now.], and click [OK] to complete setup.
KV8 Pro
Install Audio Driver
B-1
Appendix B. Install Audio Driver
The installation procedures and screen shots in
this section are based on Windows XP operating
system. For those of other OS, please follow its
on-screen instruction.
Insert the Driver & Utility CD into CD-ROM
drive, it should execute the installation program
automatically. If not, double-click the execution
file at the main directory of this CD to enter the
installation menu.
After entering the installation menu, move your
curser to [Drivers] tab. Click [Audio Driver].
The following screen appears.
3. After the system restarted, a shortcut icon
appears at the right corner of Windows task bar.
4. In this Speaker Configuration tab, select [6
channels mode for 5.1 speakers output] to
enable 6-channel audio system
1. Click [Next].
2. Choose [Yes, I want to restart my computer
now.], and click [Finish] to complete setup.
User’s Manual
B-2
Appendix B
KV8 Pro
Install LAN Driver
C-1
Appendix C. Install LAN Driver
To install the LAN driver, please insert the Driver & Utility CD into CD-ROM drive. It should execute
the installation program automatically. If not, double-click the execution file at the main directory of this
CD to enter the installation menu. The following screen appears.
Click [LAN Driver], and then follow the on-screen instruction to complete the driver installation.
User’s Manual
C-2
Appendix C
KV8 Pro
Install VIA USB 2.0 Driver
D-1
Appendix D. Install VIA USB 2.0 Driver
NOTE: There is no need to install VIA USB 2.0 driver for the Windows XP operating system with
Service Pack 1 already installed. Please run the Windows update for the latest Service Pack.
The installation procedures and screen shots in
this section are based on Windows 2000
operating system. For those of other OS, please
follow its on-screen instruction.
Insert the Driver & Utility CD into CD-ROM
drive, it should execute the installation program
automatically. If not, double-click the execution
file at the main directory of this CD to enter the
installation menu.
After entering the installation menu, move your
curser to [Drivers] tab. Click [VIA USB 2.0
Driver]. The following screen appears.
3. Click [Next].
4. Click [Yes].
1. Click [Next].
5. Click [Yes].
2. Click [Yes].
User’s Manual
D-2
Appendix D
6. Click [Yes].
7. Click [OK].
8. Click [Print to File].
9. Click [OK].
KV8 Pro
Install VIA Serial ATA RAID Driver
E-1
Appendix E. Install VIA Serial ATA RAID Driver
The installation procedures and screen shots in
this section are based on Windows XP operating
system. For those of other OS, please follow its
on-screen instruction.
Insert the Driver & Utility CD into CD-ROM
drive, it should execute the installation program
automatically. If not, double-click the execution
file at the main directory of this CD to enter the
installation menu.
After entering the installation menu, move your
curser to [Drivers] tab. Click [VIA SATA RAID
Driver]. The following screen appears.
3. Click [Next].
1. Click [Next].
4. Click [Next].
2. Click [Next].
5. Click [Next].
User’s Manual
E-2
Appendix E
8. This is the “VIA RAID Tool” configuration
menu. For more information on how to operate,
please refer to the “Help” menu.
6. Choose [Yes, I want to restart my computer
now.], and click [Finish] to complete setup.
7. After the system restarted, a shortcut icon
appears at the right corner of Windows task bar.
KV8 Pro
Install ABIT µGuru Driver
F-1
Appendix F. Install ABIT µGuru Driver
ABIT µGuru is a fresh Microprocessor developed by ABIT engineers used only on ABIT motherboards.
This processor combines the current ABIT engineered features into a user-friendly Windows-based
interface, providing users a perfect environment to maximize PC performance and stability.
To install the ABIT µGuru driver, please insert the Driver & Utility CD into CD-ROM drive. It should
execute the installation program automatically. If not, double-click the execution file at the main directory
of this CD to enter the installation menu. The following screen appears.
Move your mouse to “ABIT Utility” tab. Click [ABIT µGuru]. Follow the on-screen instruction to
complete the driver installation.
User’s Manual
F-2
Appendix F
KV8 Pro
POST Code Definition
G-1
Appendix G. POST Code Definition
AWARD POST Code Definition:
POST
Description
(hex)
CF
Test CMOS R/W functionality
Early chipset initialization:
-Disable shadow RAM
C0
-Disable L2 cache (socket 7 or below)
-Program basic chipset registers
Detect memory
C1
-Auto-detection of DRAM size, type and ECC
-Auto-detection of L2 cache (socket 7 or below)
Expand compressed BIOS code to DRAM
Call chipset hook to copy BIOS back to E000 & F000 shadow RAM
Expand the Xgroup codes locating in physical address 1000:0
Initial Superio_Early_Init switch
C3
C5
01
03
1. Blank out screen
05
07
08
2. Clear CMOS error flag
1. Clear 8042 interface
2. Initialize 8042 self-test
1. Test special keyboard controller for Winbond 977 series Super I/O chips
2. Enable keyboard interface
1. Disable PS/2 mouse interface (optional)
0A
2. Auto detect ports for keyboard & mouse followed by a port & interface swap (optional)
3. Reset keyboard for Winbond 977 series Super I/O chips
Test F000h segment shadow to see whether it is R/W-able or not. If test fails, keep
beeping the speaker
0E
10
12
14
16
18
Auto detect flash type to load appropriate flash R/W codes into the run time area in F000
for ESCD & DMI support
Use walking 1’s algorithm to check out interface in CMOS circuitry. Also set real-time
clock power status, and then check for override
Program chipset default values into chipset. Chipset default values are MODBINable by
OEM customers
Initial onboard clock generator if Early_Init_Onboard_Generator is defined. See also
POST 26.
Detect CPU information including brand, SMI type (Cyrix or Intel) and CPU level (586
or 686)
Initial interrupts vector table. If no special specified, all H/W interrupts are directed to
SPURIOUS_INT_HDLR & S/W interrupts to SPURIOUS_soft_HDLR.
1B
1D
Initial EARLY_PM_INIT switch
User’s Manual
G-2
Appendix G
1F
21
Load keyboard matrix (notebook platform)
HPM initialization (notebook platform)
1. Check validity of RTC value: e.g. a value of 5Ah is an invalid value for RTC minute.
23
24
2. Load CMOS settings into BIOS stack. If CMOS checksum fails, use default value
instead.
Prepare BIOS resource map for PCI & PnP use. If ESCD is valid, take into consideration
of the ESCD’s legacy information.
Early PCI Initialization:
-Enumerate PCI bus number.
25
-Assign memory & I/O resource
-Search for a valid VGA device & VGA BIOS, and put it into C000:0
1. If Early_Init_Onboard_Generator is not defined Onboard clock generator initialization.
Disable respective clock resource to empty PCI & DIMM slots.
26
27
29
2. Init onboard PWM
3. Init onboard H/W monitor devices
Initialize INT 09 buffer
1. Program CPU internal MTRR (P6 & PII) for 0-640K memory address.
2. Initialize the APIC for Pentium class CPU.
3. Program early chipset according to CMOS setup. Example: onboard IDE controller.
4. Measure CPU speed.
2B
2D
Invoke Video BIOS
1. Initialize double-byte language font (Optional)
2. Put information on screen display, including Award title, CPU type, CPU speed, full
screen logo.
Reset keyboard if Early_Reset_KB is defined e.g. Winbond 977 series Super I/O chips.
See also POST 63.
33
35
37
39
3C
3E
40
43
47
Test DMA Channel 0
Test DMA Channel 1.
Test DMA page registers.
Test 8254
Test 8259 interrupt mask bits for channel 1
Test 8259 interrupt mask bits for channel 2
Test 8259 functionality
Initialize EISA slot
1. Calculate total memory by testing the last double word of each 64K page
2. Program writes allocation for AMD K5 CPU
1. Program MTRR of M1 CPU
49
2. Initialize L2 cache for P6 class CPU & program CPU with proper cacheable range
3. Initialize the APIC for P6 class CPU
4E
4. On MP platform, adjust the cacheable range to smaller one in case the cacheable ranges
between each CPU are not identical
50
52
53
Initialize USB
Test all memory (clear all extended memory to 0)
Clear password according to H/W jumper (Optional)
KV8 Pro
POST Code Definition
G-3
55
57
Display number of processors (multi-processor platform)
Display PnP logo
Early ISA PnP initialization
-Assign CSN to every ISA PnP device
Initialize the combined Trend Anti-Virus code
59
5B
(Optional Feature) Show message for entering AWDFLASH.EXE from FDD (optional)
1. Initialize Init_Onboard_Super_IO
5D
60
2. Initialize Init_Onbaord_AUDIO
Okay to enter Setup utility; i.e. not until this POST stage can users enter the CMOS setup
utility
63
65
67
69
Reset keyboard if Early_Reset_KB is not defined
Initialize PS/2 Mouse
Prepare memory size information for function call: INT 15h ax=E820h
Turn on L2 cache
Program chipset registers according to items described in Setup & Auto-configuration
table
6B
1. Assign resources to all ISA PnP devices
6D
2. Auto assign ports to onboard COM ports if the corresponding item in Setup is set to
“AUTO”
1. Initialize floppy controller
6F
75
2. Set up floppy related fields in 40:hardware
Detect & install all IDE devices: HDD, LS120, ZIP, CDROM …
(Optional Feature)
Enter AWDFLASH.EXE if:
76
-AWDFLASH is found in floppy drive
-ALT+F2 is pressed
77
7A
7C
Detect serial ports & parallel ports.
Detect & install co-processor
Init HDD write protect
Switch back to text mode if full screen logo is supported
-If errors occur, report errors & wait for keys
-If no errors occur or F1 key is pressed to continue: Clear EPA or customization logo
7F
E8POST.ASM starts
1. Call chipset power management hook
2. Recover the text font used by EPA logo (not for full screen logo)
3. If password is set, ask for password
Save all data in stack back to CMOS
Initialize ISA PnP boot devices
82
83
84
1. USB final Initialization
85
87
89
2. Switch screen back to text mode
NET PC: Build SYSID Structure
1. Assign IRQs to PCI devices
2. Set up ACPI table at top of the memory.
User’s Manual
G-4
Appendix G
1. Invoke all ISA adapter ROMs
2. Invoke all PCI ROMs (except VGA)
1. Enable/Disable Parity Check according to CMOS setup
2. APM Initialization
8B
8D
8F
93
Clear noise of IRQs
Read HDD boot sector information for Trend Anti-Virus code
1. Enable L2 cache
2. Program Daylight Saving
3. Program boot up speed
4. Chipset final initialization.
94
5. Power management final initialization
6. Clear screen & display summary table
7. Program K6 write allocation
8. Program P6 class write combining
Update keyboard LED & typematic rate
1. Build MP table
95
96
FF
2. Build & update ESCD
3. Set CMOS century to 20h or 19h
4. Load CMOS time into DOS timer tick
5. Build MSIRQ routing table
Boot attempt (INT 19h)
KV8 Pro
POST Code Definition
G-5
AC2003 POST Code Definition:
POST
Description
(hex)
Power On Sequence
8.1.
8.2.
8.3.
8.4.
8.5.
8.6.
8.7.
8.8.
8.9.
8.A.
8.B.
8.C.
8.D.
8.D.
8.E.
8.F.
Start power on sequence
Enable ATX power supply
ATX power supply ready
DDR voltage ready
Setup PWM for CPU core voltage
Assert PWM for CPU core voltage
Check CPU core voltage
CPU core voltage ready
Initial clock generator IC
North Bridge chipset voltage ready
AGP voltage ready
3VDUAL voltage ready
VDDA 2.5V voltage ready
GMCHVTT voltage ready
Check CPU fan speed
Assert all power ready
Complete uGuru initial process
AWARD BIOS take over booting job
9.0.
Power Off Sequence
9.1.
9.2.
9.3.
9.4.
9.5.
9.6.
9.7.
9.8.
9.9.
Start power off sequence
De-Assert all power
Se-Assert power on
De-Assert LDT Bus power
De-Assert PWM for CPU core voltage
De-Assert CPU core voltage
Check CPU core voltage
De-Assert ATX power supply
Complete power off sequence
Others
F.0.
F.1.
F.2.
F.3.
Button reset
SoftMenu reset
Power on sequence timeout
Power off sequence timeout
NOTE: The decimal point lights up when executing the AC2003 POST action.
User’s Manual
G-6
Appendix G
KV8 Pro
Troubleshooting (Need Assistance?)
H-1
Appendix H. Troubleshooting (Need Assistance?)
Q & A:
Q: Do I need to clear the CMOS before I use a new motherboard to assemble my new computer
system?
A: Yes, we highly recommend that you clear the CMOS before installing a new motherboard. Please
move the CMOS jumper from its default 1-2 position to 2-3 for a few seconds, and then back. When
you boot up your system for the first time, follow the instructions in the user's manual to load the
optimized defaults.
Q: If my systems hang when I update the BIOS or set the wrong CPU parameters, what should I
do?
A: Whenever you update the BIOS or if the system hangs due to wrong CPU parameters setting, always
clear CMOS jumper before booting up again.
Q: Why the system failed to boot up and nothing was displayed on the screen after I did some
over-clocking or non-standard settings inside the BIOS? Is the motherboard dead? Do I need to
return it to where I bought from or go through an RMA process?
A: It should not cause hardware or permanent damage to motherboard when BIOS settings were
changed from default to over-clocking or non-standard status.
We suggest the following three troubleshooting methods to discharge CMOS data, recover the
hardware default status, and then make the motherboard working again. No need to bother returning
the motherboard to where you bought from or go through an RMA process.
Step 1. Switch off the power supply unit and then switch it on again after one minute. If there is no
power switch on the power supply unit, disconnect its power cord for one minute and then
connect it back.
Press and hold the <Insert> key on the keyboard, press the power-on button to boot up
system. If it works, loose the <Insert> key and hit <Del> key to enter the BIOS setup page to
do the correct settings.
If the situation remains the same, repeat the procedures in Step 1 for three times, or try Step
2.
Step 2. Switch off the power supply unit or disconnect the power cord. Open the chassis cover.
Locate the CCMOS jumper near the button battery. Change the jumper position from default
1-2 to 2-3 for one minute to discharge the CMOS data, and then put it back to default 1-2
position.
Close the chassis and switch on the power supply unit or plug in the power cord. Press the
power-on button to boot up system. If it works, hit <Del> key to enter the BIOS setup page
to do the correct settings.
If the situation remains the same, try Step 3.
Step 3. The same procedure as Step 2, but in the meantime of discharging the CMOS data, pull out
ATX power connectors from motherboard and remove the button battery during CMOS
discharging.
User’s Manual
H-2
Appendix H
Q: How can I get a quick response to my request for technical support?
A: Be sure to follow the guidelines as stated in the “Technical Support Form” section of this manual.
If you have a problem during operation, in order to help our technical support personnel quickly
determine the problem with your motherboard and give you the answers you need, before filling in
the technical support form, eliminate any peripheral that is not related to the problem, and indicate it
on the form. Fax this form to your dealer or to the company where you bought the hardware in order
to benefit from our technical support. (You can refer to the examples given below)
Example 1:
With a system including: motherboard (with CPU, DRAM, COAST...) HDD, CD-ROM, FDD, VGA
CARD, MPEG CARD, SCSI CARD, SOUND CARD, etc. After the system is assembled, if you
cannot boot up, check the key components of the system using the procedure described below. First
remove all interface cards except the VGA card and try to reboot.
If you still cannot boot up: Try installing another brand/model VGA card and see if the system will
start. If it still does not start, note the VGA card model, motherboard model, Bios identification
number, CPU on the technical support form (refer to main instructions), and describe the problem in
the problem description space provided.
If you can boot up: Insert the interface cards you have removed back into the system, one by one
and try to start the system each time you insert a card, until the system will not start. Keep the VGA
card and the interface card that caused the problem inserted on the motherboard, remove any other
cards or peripheral, and start again. If you still cannot start, note the information related to both cards
in the add-on Card space provided, and don’t forget to indicate the motherboard model, version,
BIOS identification number, CPU (refer to main instructions), and give a description of the problem.
Example 2:
With a system including the motherboard (with CPU, DRAM, COAST...) HDD, CD-ROM, FDD,
VGA CARD, LAN CARD, MPEG CARD, SCSI CARD, SOUND CARD, after assembly and after
having installed the Sound Card Driver, when you restart the system, when it runs the Sound Card
Driver, it resets automatically. This problem may be due to the Sound Card Driver. During the
Starting DOS… procedure, press SHIFT (BY-PASS) key, to skip CONFIG.SYS and
AUTOEXEC.BAT; edit CONFIG.SYS with a text editor, and in function the line that loads the
Sound Card Driver, add a remark REM, in order to disable the Sound Card Driver. See the example
below.
CONFIG.SYS:
DEVICE=C:\DOS\HIMEM.SYS
DEVICE=C:\DOS\EMM386.EXE HIGHSCAN
DOS=HIGH, UMB
FILES=40
BUFFERS=36
REM DEVICEHIGH=C:\PLUGPLAY\DWCFGMG.SYS
LASTDRIVE=Z
Restart the system. If the system starts and does not reset, you can be sure that the problem is due to
the Sound Card Driver. Write down the Sound Card model, motherboard model, BIOS identification
number on the technical support file (refer to main instructions), and describe the problem in the
space provided.
We will show you how to fill the “Technical Support Form”.
KV8 Pro
Troubleshooting (Need Assistance?)
H-3
Main instructions:
To fill in this “Technical Support Form”, refer to the step-by-step instructions given below:
1*. MODEL: Note the model number given in your user’s manual.
Example: KV8 Pro
2*. Motherboard model number (REV): Note the motherboard model number labeled on the
motherboard as “REV:*.**”.
Example: REV: 1.01
3*. BIOS ID and Part Number: See the on screen message.
4. DRIVER REV: Note the driver
version number indicated on the
DEVICE DRIVER disk (if any) as
“Release *.**”. For example:
5*. OS/APPLICATION: Indicate the
operating system and applications
you are running on the system.
Example: MS-DOS® 6.22,
Windows® 98 SE, Windows® 2000, etc....
6*. CPU: Indicate the brand and the speed (MHz) of your CPU.
Example:(A) In the “Brand” space, write “Intel”; in the “Specifications” space, write “Pentium®
1.9GHz”.
4
7. HDD: Indicate the brand and specifications of your HDD(s); specify if the HDD is using ꢀIDE1 or
ꢀIDE2. If you know the disk capacity, indicate it and check (“ꢁ”) “ ”; in case you give no
indication, we will consider that your HDD is “ꢂIDE1” Master.
Example: In the “HDD” space, check the box; in the Brand space, write “Seagate”; in the
Specifications space, write “ST31621A (1.6GB)”.
8. CD-ROM Drive: Indicate the brand and specifications of your CD-ROM drive. Specify if it uses ꢀ
IDE1 or ꢀIDE2， and check (“ꢁ”) “ ”; in case you give no indication, we will consider that your
CD-ROM is “ꢂIDE2” Master.
Example: In the “CD-ROM drive” space, check the box, in the Brand space, write “Mitsumi”, in the
Specifications space, write “FX-400D”.
9. System Memory (DDR SDRAM): Indicate the brand and specifications (DDR DIMM) of your
system memory. Such as Density, Description, Module Components, Module Part Number, CAS
Latency, and Speed (MHz).
For example: In the Brand space, write “Micron”; in the Specifications space, write: Density:
128MB, Description: SS 16 Megx72 2.5V ECC Gold, Module Components: (9) 16 Megx 8,
Module Part Number: MT9VDDT1672AG, CAS Latency: 2, Speed (MHz): 200 MHz.
Please give us the detailed information of your DDR SDRAM module; it will help us to simulate the
problems you met.
10. ADD-ON CARD: Indicate which add-on cards you are absolutely sure are related to the problem.
If you cannot identify the problem’s origin, indicate all the add-on cards inserted into your system.
NOTE: Items between the “*” are absolutely necessary.
User’s Manual
H-4
Appendix H
ꢀ Technical Support Form
ꢀ Company Name:
ꢁ Contact Person:
ꢀ E-mail Address:
ꢀ Phone Number:
ꢂ Fax Number:
Model
*
*
BIOS ID #
*
Motherboard Model No.
OS/Application
DRIVER REV
Hardware Name
CPU
Brand Specifications
*
IDE1
HDD
IDE2
IDE1
IDE2
CD-ROM-Drive
System Memory
ADD-ON CARD
Problem Description:
KV8 Pro
How to Get Technical Support
I-1
Appendix I. How to Get Technical Support
(From our website) http://www.abit.com.tw
(In North America) http://www.abit-usa.com
(In Europe) http://www.abit.nl
Thank you for choosing ABIT products. ABIT sells all our products through distributors,
resellers and system integrators; we have no direct sales to end-users. Before sending email
for tech support please check with your resellers or integrators if you need any services, they
are the ones who sold you your system and they should know best as to what can be done,
how they serve you is a good reference for future purchases.
We appreciate every customer and would like to provide the best service to you. Providing
fast service to our customers is our top priority. However we receive many phone calls and a
huge amount of email from all over the world. At the present time it is impossible for us to
respond to every single inquiry. Therefore it is quite possible that if you send an email to us
that you may not receive a response.
We have done many compatibility tests and reliability tests to make sure our products have
the best quality and compatibility. In case you need service or technical support, please
understand the constraint we have and always check with the reseller who sold the product
to you first.
To expedite service, we recommend that you follow the procedures outlined below before
contacting us. With your help, we can meet our commitment to provide the best service to the
greatest number of ABIT customers:
1. Check the Manual. It sounds simple but we have taken a lot of care in making a
well-written and thorough manual. It is full of information that doesn't only pertain to
motherboards. The CD-ROM included with your board will have the manual as well as
drivers. If you don't have either one, go to our Program Download Area of the Website or
FTP server.
2. Download latest BIOS, software or drivers. Please go to our Program Download area
on our Website to check to see if you have the latest BIOS. They are developed over
periods of time to fixes bugs or incompatibilities. Also please make sure you have the
latest drivers from your peripheral cards makers!
3. Check the ABIT Technical Terms Guide and FAQ on our Website. We are trying to
expand and make the FAQs more helpful and information rich. Let us know if you have
any suggestions. For hot topics, check out our HOT FAQ!
User’s Manual
I-2
Appendix I
4. Internet Newsgroups. They are a great source of information and many people there can
forum for the public to exchange information and discuss experiences they have had with
ABIT products. Many times you will see that your question has already been asked before.
This is a public Internet news group and it is reserved for free discussions. Here is a list of
some of the more popular ones:
5. Ask your reseller. Your ABIT authorized distributor should be able to provide the fastest
solution to your technical problem. We sell our products through distributors who sell to
resellers and stores. Your reseller should be very familiar with your system configuration
and should be able to solve your problem much more efficiently than we could. After all,
your reseller regards you as an important customer who may purchase more products and
who can urge your friends to buy from him or her as well. They integrated and sold the
system to you. They should know best what your system configuration is and your
problem. They should have reasonable return or refund policies. How they serve you is
also a good reference for your next purchase.
6. Contacting ABIT. If you feel that you need to contact ABIT directly you can send email
to the ABIT technical support department. First, please contact the support team for the
branch office closest to you. They will be more familiar with local conditions and
problems and will have better insight as to which resellers offer what products and
services. Due to the huge number of emails coming in every day and other reasons, such
as the time required for problem reproduction, we will not be able to reply to every email.
Please understand that we are selling through distribution channels and don't have the
resources to serve every end-user. However, we will try to do our best to help every
customer. Please also remember that for many of our technical support team English is a
second language, you will have a better chance of getting a helpful answer if your
question can be understood in the first place. Be sure to use very, simple, concise
language that clearly states the problem, avoid rambling or flowery language and always
list your system components. Here is the contact information for our branch offices:
KV8 Pro
How to Get Technical Support
I-3
North America and South America:
Japan:
ABIT Computer (U.S.A.) Corporation
45531 Northport Loop West,
Fremont, California 94538, U.S.A.
Tel: 1-510-623-0500
ABIT Computer (Japan) Co. Ltd.
Fax: 81-3-5396-5110
Fax: 1-510-623-1092
Shanghai:
ABIT Computer (Shanghai) Co. Ltd.
Tel: 86-21-6235-1829
Fax: 86-21-6235-1832
U.K. and Ireland:
ABIT Computer (U.K.) Corporation
Ltd.
Russia:
ABIT Computer (Russia) Co. Ltd.
Fax: 7-095-937-2837
Unit 3, 24-26 Boulton Road,
Stevenage, Herts SG1 4QX, U.K.
Tel: 44-1438-228888
Fax: 44-1438-226333
France, Italy, Spain, Portugal, and
Greece:
Germany, Benelux (Belgium,
Netherlands, Luxembourg), Denmark,
Norway, Sweden, Finland, and
Switzerland:
ABIT Computer France SARL
Tel: 33-1-5858-0043
Fax: 33-1-5858-0047
AMOR Computer B.V. (ABIT’s
European Office)
Van Coehoornstraat 7,
5916 PH Venlo, The Netherlands
Tel: 31-77-3204428
Fax: 31-77-3204420
All other territories not covered above
please contact Taiwan Head Office:
When contacting our headquarters please
Note we are located in Taiwan and we are
8+ GMT time. In addition, we have
holidays that may be different from those
in your country.
Austria, Czech, Romania, Bulgaria,
Yugoslavia, Slovakia, Slovenia, Croatia,
Bosnia, Serbia, and Macedonia:
ABIT Computer Corporation
No.323, Yang Guang St., Neihu, Taipei,
114, Taiwan
Tel: 886-2-8751-8888
Fax: 886-2-8751-3382
Asguard Computer Ges.m.b.H
Schmalbachstrasse 5,
A-2201 Gerasdorf/Wien, Austria
Tel: 43-1-7346709
Fax: 43-1-7346713
User’s Manual
I-4
Appendix I
7. RMA Service. If your system has been working but it just stopped, but you have not
installed any new software or hardware recently, it is likely that you have a defective
component. Please contact the reseller from whom you bought the product. You should be
able to get RMA service there.
8. Reporting Compatibility Problems to ABIT. Because of tremendous number of email
messages we receive every day, we are forced to give greater weight to certain types of
messages than to others. For this reason, any compatibility problem that is reported to us,
giving detailed system configuration information and error symptoms will receive the
highest priority. For the other questions, we regret that we may not be able to reply
directly. But your questions may be posted to the Internet news group in order that a
larger number of users can have the benefit of the information. Please check the news
group from time to time.
9. The information listed below are some chipset vendors’ WEB site addresses for your
reference:
HighPoint Technology Inc.’s WEB site: http://www.highpoint-tech.com/
Intel’s WEB site: http://www.intel.com/
Silicon Image’s WEB site: http://www.siimage.com/
SiS’ WEB site: http://www.sis.com.tw/
VIA’s WEB site: http://www.via.com.tw/
Thank You
ABIT Computer Corporation
KV8 Pro
|
