AT T DECT CL82109 User Manual

Quick start guide

CL82109/CL82209/CL82309/

CL82359/CL82409/CL82509/

CL82609/CL82659/CL82859

DECT 6.0 corded/cordless

telephone/answering system

with caller ID/call waiting

Telephone base & charger installation

Install the telephone as shown below.

The telephone base is ready for tabletop use. If you want to change to wall

mounting, see user’s manual for details.

2. Route the power adapter cord through the slot.

1. Plug one end of

the telephone line

cord into the

3. Plug the small

end of the

telephone jack on

the bottom of the

telephone base.

telephone base

power adapter

into the power

jack on the

bottom of the

telephone base.

7. Raise the antenna.

4. Place the cords

into the

channels.

Telephoneline

cord

Power

adapter

5. Plug the large end of

the power adapter

into a power outlet

not controlled by a

wall switch.

6. Plug the other end

of the telephone

line cord into a

telephone jack or a

DSL filter.

If you have DSL high

speed Internet

service, a DSL filter

(not included) is

required.

Charger

installation

Plug the power adapter

into an electrical outlet

not controlled by a wall

switch.

IMPORTANT INFORMATION

1. Use only the power adapter(s) supplied with this product. To order a replacement power

^{adapter, visit our website at}www.telephones.att.com, or call

1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.

2. The power adapters are intended to be correctly oriented in a vertical or floor mount position.

The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-

the-table or cabinet outlet.

Battery installation & charging

Install the battery as shown below. Once you have installed the battery, the

screen indicates the battery status (see table below). If necessary, place the

handset in the telephone base or charger to charge the battery. For best

performance, keep the handset in the charger when not in use. The battery is

fully charged after 16 hours of continuous charging. See the table on the

Technical specifications page of the user’s manual for battery

operating times.

If the screen is blank, you need to charge the handset without interruption

for at least 10 minutes to give the handset enough charge to use the

telephone for a short time. The screen shows LOW BATTERY and the

backlight is off until you have charged the battery without interruption for at

least one hour. The following table summarizes the battery charge indicators

and actions take.

Battery indicators

Battery status

Action

The screen is blank.

Battery has no charge and the

handset cannot be used.

Charge without interruption until

the screen shows LOW BATTERY

(at least 10 minutes).

The screen shows PLACE Battery has very little charge

Charge without interruption until

IN CHARGER and

and the handset cannot be used. the screen shows LOW BATTERY

flashes.

(at least four minutes).

The screen shows LOW

Battery has enough charge to

Charge until the screen shows

BATTERY and flashes. be used for a short time.

HANDSET X (about one hour).

The screen shows

Battery is charged.

To keep the battery charged,

place it in the telephone base or

charger when not in use.

HANDSET X.

NOTE: If you are on a phone call in low battery mode, you hear four short beeps

every minute.

Step 1

Step 2

Plug the battery securely into the

connector inside the handset battery

compartment, matching the color-coded

Align the cover flat against the

battery compartment, then slide

it upwards until it clicks into

label. Insert the supplied battery with the place.

label THIS SIDE UP facing up as indicated.

Battery installation and charging

Step 3

Charge the handset by placing it face up in the

telephone base or charger. The CHARGE light on the top

of the handset is on during charging.

IMPORTANT INFORMATION

1. Use only the supplied rechargeable battery or replacement battery (model

BT8001). To order, visit our website at www.telephones.att.com or call

1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.

2. If you do not use the handset for a long time, disconnect and remove the battery

to prevent possible leakage.

Quick reference guide - handset

MENU/SELECT

CHARGE indicator

On when the handset is

charging in the telephone

base or charger.

Press to show the menu.

While in the menu, press to

select an item or save an

entry or setting.

TCID/-VOLUME

DIRS/+VOLUME

Press TCID to display caller ID

history.

Press DIRS to show

directory entries.

Press to scroll down while in

menus.

Press to scroll up while in

menus.

While entering names or

numbers, press to move the

cursor to the left.

While entering names or

numbers, press to move the

cursor to the right.

Press to decrease the listening

volume when on a call.

Press to increase the

listening volume when on a

call.

PHONE/FLASH

Press to make or answer a

call.

OFF/CLEAR

During a call, press to hang

up.

During a call, press to answer

an incoming call when you

receive a call waiting alert.

While in a menu, press to

cancel an operation, back up

to the previous menu, or exit

the menu display.

Press and hold while the

telephone is not in use to

erase the missed calls

indicator.

While reviewing a call log

entry, press repeatedly to add

or remove 1 in front of the

telephone number before

dialing or saving it in the

directory.

Press repeatedly to display

other dialing options when

reviewing a call log entry.

MUTE/DELETE

During a call, press to mute

the microphone.

REDIAL/PAUSE

Press repeatedly to view the

last five numbers dialed.

While reviewing the caller ID

history, the directory or the

redial memory, press to delete

an individual entry.

While entering numbers,

press and hold to insert a

dialing pause.

While predialing, press to

delete digits.

INT

Press to begin an intercom

conversation or to transfer a

call.

SPEAKER

Press to switch between

speakerphone and handset.

Quick reference guide - handset

Main menu

ANS. SYSTEM

DIRECTORY

> shows a highlighted item

?!BOT/TZTUFN

EJSFDUPSZ

CALL LOG

EJSFDUPSZ

RINGER VOLUME

RINGER TONE

KEY TONE

LCD LANGUAGE

SET DATE/TIME

CLR VOICEMAIL

HOME AREA CODE

Using menus

Press MENU/SELECT to show the first

menu item, ANS. SYSTEM.

Press TCID or DIRS to scroll through

menu items.

Press MENU/SELECT to select or save

changes to a highlighted menu item.

Press OFF/CLEAR to cancel an

operation, back up to the previous

menu, or exit the menu display.

Quick reference guide - telephone base

IN USE indicator

On when the handset is in

use, when the answering

system is answering an

incoming call or when you

are registering a handset.

VOICEMAIL indicator

Flashes when you have new

voicemail. Voicemail service

is offered by your local

telephone company, and is

different from answering

system messages.

Flashes when another

telephone is in use on the

same line, or when you are

deregisteringhandset(s)from

the telephone base.

Flashes quickly when there is

an incoming call.

HANDSET LOCATOR

Press to make handsets beep

so you can locate them.

MESSAGE COUNTER

PLAY/STOP

Number of messages (or

during playback, message

number currently playing).

Press to start or stop

message playback.

XDELETE

Press to delete the

message currently playing.

REPEAT

Press to repeat a

message.

Press twice to delete all

old messages when the

phone is not in use.

Press twice to play the

previous message.

ANSWER ON/OFF

SKIP

Press to turn the

answering system on or

off.

Press to skip a

message.

VOLUME ST

During message playback,

press to adjust the

listening volume.

While in idle mode, press

to adjust the base ringer

volume.

www.telephones.att.com

AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed to

Advanced American Telephones, San Antonio, TX 78219.

Printed in China. Issue 4 AT&T 09/09.

HP Hewlett Packard Hewlett Packard Computer Monitor W2371D User Manual
GE 25202 User Manual
Foster e 7370 230 User Manual
Electrolux Thermaline WLWWCFOOOO User Manual
Dimplex DS5629 User Manual
Diamond Multimedia Radeon X1050 User Manual
Cypress CY7C024BV User Manual
ClearOne comm Audio Conferencing User Manual
Atmel ATmega88PA User Manual
Acnodes PMW6190 User Manual