2
User’s Manual for
Cordless Digital
Answering System
Telephone 7625
Part 2
© 1998 Philips Consumer Communicaitons L.P. All rights reserved.
Printed in Mexico 848232914 Issue1AT&T
Please read Part 1—Important Product Information,
included in your package.
TABLE OF CONTENTS
INSTALLATION
Ring Select, Toll Saver and the Remote Access Code. . . . . . . . . . . . . . 16
Reviewing the Setting in the Feature Set-Up Menu . . . . . . . . . . . . . . . 18
Volume Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Incoming Message Length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Memory Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Antenna
MUTE/LOW
BATT indicator
Accesses
the
answering
system
Answering System Operation: At the Base
19
Answering Calls and Recording Messages. . . . . . . . . . . . . . . . . . . . . . 19
Screening and Intercepting Incoming Calls . . . . . . . . . . . . . . . . . . . . . 19
Listening to Your Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Saving Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Deleting Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Recording a Memo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Power Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Turns ringer on
or off (side of
handset)
Makes
a call
Answering System Operation:
Away From the Base (Cordless Handset/Remote)
22
Mutes
a call
Accessing the Answering System from the Cordless Handset . . . . . . . . 22
Accessing the Answering System from a Touch Tone Phone . . . . . . . . 23
Voice Help Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Remote Access Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
The Outgoing Announcement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Recording a Memo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
The Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Remote On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Recording a Message When the System is Off . . . . . . . . . . . . . . . . . . . 28
To Exit Remote Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Call Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Announcement Bypass. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Redials last
call made
Programs
a number
in memory
Accesses
custom calling
services
Temporary
Tone
Changes
handset
receiver
volume
Audible Signals
Batteries
29
30
Charging the Handset Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Changes
channels
Replacing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
In Case of Difficulty
31
2
3
INSTALLATION
INSTALLATION
Electrical
outlet
Telephone
jack
The base antenna is upright
Keep base antenna
fully extended
Use CLOCK with
CHANGE to set or
change time/day
Accesses
answering
system
Use CHANGE
with CLOCK
and ANNC
Use ANNC with
CHANGE to
record outgoing
announcement
set up
Records a
memo
Power cord
Deletes a
message
Battery pack
Plays a
message
Turns
answering
system
on or off
Battery
compartment
Skips a
message
Stops playing
a message
Adjusts volume
Repeats a
message
Message
counter
Handset
ringer switch
Battery
compartment cover
CHARGING/HANDSET IN USE
indicator
Page/Handset
locator
4
5
INSTALLATION
INSTALLATION
The instructions below are for both table and wall installation.
FOR WALL MOUNTING ONLY
Turn the base over and you will see a wedged, triangular-shaped plastic piece
that is attached to the bottom of the base. This is the mounting bracket. For
wall mounting, the mounting bracket must be attached to the base so that the
thickest end of the bracket is facing the floor (in wall mount position).
1
Choose a spot near an electrical outlet and a telephone jack.
•
This phone requires a modular telephone jack and a standard electrical
outlet (110v AC).
•
The outlet should not be controlled by a wall switch; if the switch is
turned off, operation can be affected.
To wall mount the phone:
•
Remove the mounting bracket by pushing in the two tabs at the large
end of the bracket and lifting the bracket from the base.
2
Install the handset battery.
•
•
•
Remove the battery compartment cover on the handset by pressing on
the indentation and sliding the cover downward.
•
Plug the power cord into the jack labeled POWER
on the back of
the base. Guide the power cord from the jack through the straight
channel on the bottom of the base, so that any excess cord extends
straight out of the channel end farthest from the jack. Wrap any
excess cord around the two crescent-shaped tabs on the underside of
the mounting bracket but be sure to leave enough cord free to extend
to an electrical outlet.
Plug the battery pack cord into the handset, insert the battery pack and
rest the cords on top of the battery pack.
Replace the cover by sliding it on its track up over the battery
compartment until it snaps firmly in place.
3
Set the handset ringer switch.
Set the switch on the side of the handset to ON so the handset will ring.
When this switch is set to OFF, the handset will not ring.
•
Plug one end of the telephone line cord into the jack on the base.
Guide the cord from the jack through the curved channel on the
bottom of the base. Wrap any excess cord around the two crescent-
shaped tabs on the underside of the mounting bracket but be sure to
leave enough cord free to extend to the wall jack. Take the end of the
cord and insert it through the rectangular-shaped hole in the center of
the bracket.
NOTE: If you set the ringer switch to OFF, the handset battery will last
longer. However, when the ringer switch is set to OFF, you will always
*
need to press
on the handset to answer a call, even if the handset
has been in the base. When the ringer switch is set to OFF, the ANS SYS
light will not flash to indicate new messages.
•
•
Place the bracket back on the base so that the thickest end of the
bracket will be closest to the floor when in wall mount position.
4
Connect the telephone line and power cords.
CAUTION: Use only the AC power adapter supplied with this
telephone. Power Supply HADW-1; Input: 120V AC, 60Hz, 16 W;
Output: 12V DC, 900mA
Plug the end of the telephone line cord into the modular phone jack
on the wall. Make sure the plug snaps firmly into place.
FOR TABLE INSTALLATION ONLY
•
Plug one end of the telephone line cord into the jack on the base. Plug
the other end of the line cord into a modular phone jack. Make sure
the plug snaps firmly in place.
•
Plug the power cord into the jack labeled POWER
the base. Plug the AC adapter on the power cord into an
electrical outlet.
on the back of
NOTE: When the system is first connected to AC power, it will go
through an automatic initialization routine. After this routine is completed,
CL will flash in the message counter display, indicating that the clock
needs to be set. See “Setting the Clock” in the section on “ANSWERING
SYSTEM SET-UP.”
*
6
7
INSTALLATION
TELEPHONE OPERATION (From the Handset)
•
Mount the base on the wall by holding the base so that the mounting
Making a Call
knobs on the standard wall jack will fit into the keyhole slots on the
base. Slide the base bracket down onto the knobs until it locks into
place. The cradle will support the handset when the base is on
the wall.
1
Press
on the handset. The PHONE light will go on.
2
When you hear a dial tone, dial the number.
Answering a Call
•
Plug the AC adapter on the power cord into an electrical outlet.
If the handset is in the base:
See note under Item 4.
1
2
Lift the handset.
Plug into
electrical outlet
The PHONE light goes on and the call will be connected.
If the Ringer Switch is set to OFF, or if the handset is away from the base:
1
2
Press
on the handset.
Telephone line cord
Power cord
The PHONE light goes on and the call will be connected.
NOTE: Although ringing will stop when you answer, you might not be
able to hear the other party until the PHONE light goes on steadily.
*
Plug into base unit
Ending a Call Using the Handset
If you are near the base:
Plug into modular
phone jack
•
Place the handset in the base.
If you are away from the base:
Press
Plug into back of
base unit
•
.
5
6
Position the base antenna so that it points upwards.
Charge the handset batteries before use.
Handset Volume
The handset VOLUME button allows you to increase or decrease the loudness
of an incoming voice. The handset volume can be set to three different levels.
Each time you press VOLUME, the level changes.
Place the handset in the base. The CHARGING light on the base goes on
to show the handset is in the right position to charge the batteries. This
phone requires 10 hours of charging. The handset will not operate until the
batteries are charged.
Flash
Press
7
Check for dial tone.
After the batteries are charged, pick up the handset. Check for dial tone by
to activate custom calling services such as Call Waiting or
pressing
dial tone. Press
; the PHONE light should go on and you should hear a
again to turn the phone off.
Three-Way Calling. You may have to press other buttons before or after
as explained in the custom calling instructions provided by your local
phone service company.
8
Set the dial mode.
If you have touch tone service, the phone will be ready to use as soon as
the battery is charged.
Redial
The last number dialed (up to 16 digits) on the phone is stored in redial
memory until you dial another number.
NOTE: If you have dial pulse service you will need to set the dial mode
*
by pressing
,
,
,
,
. To return to touch tone
1
2
Press
and wait for the PHONE light to go on.
dialing with touch tone service, press
when the phone is OFF.
,
,
,
,
.
When you hear a dial tone, press
.
8
9
TELEPHONE OPERATION (From the Handset)
TELEPHONE OPERATION (From the Base)
Mute
Page
The Mute feature allows you to hear your caller, but prevents the caller from
hearing you.
The Page feature allows you to signal someone at the handset from the base.
•
•
Make sure the Handset In Use light is not lit on the base.
To activate the Mute feature:
Press
on the base. A three-part paging tone will
•
•
Press
.
sound at the handset.
The MUTE/LOW BATT light will go on and the caller will not be able to
hear you.
NOTE: The handset Ringer Switch must be set to ON to operate the
PAGE feature.
*
To let the caller hear you again:
•
•
Press
.
Handset Locator
This feature is useful if you misplace the handset.
The MUTE/LOW BATT light will go off and the caller can hear you again.
To locate the handset using this feature:
Temporary Tone
•
Press and hold
seconds. A repeating paging tone is sounded in the handset.
To cancel the handset locator feature:
on the base for approximately four
NOTE: If you have touch tone service, you do not need to use the
*
Temporary Tone feature.
If you have dial pulse (rotary) service, this feature allows you to enter codes or
tones needed to operate certain answering machines or to use electronic bank-
ing services, calling cards, and other special services. This feature will operate
most special services; however, some services may actually require a touch
tone line. To be sure, ask the company that provides the special service.
•
Press
on the handset or
on the base.
NOTE: The Handset Locator feature will turn itself off in approximately
three minutes if you haven’t turned it off before then.
*
1
Dial the call, then press
tone signals.
. Any dial buttons pressed after this send
2
After you hang up, the phone automatically returns to dial pulse (rotary)
dialing.
Recording a Telephone Conversation
Once you have established a connection with the answering system, you can
record a telephone conversation. The telephone conversation will be recorded
along with other messages.
1
While you are having a conversation on the cordless handset, press
and wait for the ANS SYS light to go on to show that you have
made a connection with the answering system. Press
.
2
3
The system will beep once and start recording from the telephone line. The
recording will be treated as a new message.
To stop recording, press
.
10
11
OPERATING RANGE
MEMORY
This cordless integrated telephone answering system operates at the maximum
power allowed by the Federal Communications Commission (FCC). Even so,
the handset and base can communicate over only a certain distance—which
can vary with the locations of the base and handset, the weather, and the con-
struction of your home or office.
This cordless answering system can store 10 different phone numbers that you
can dial just by pressing
and one of the number buttons.
Storing Memory Numbers
1
2
3
4
5
Make sure the handset is OFF.
Press
Enter the phone number (up to 16 digits).
Press
NOTE: For best performance, point the base antenna upwards, as shown
in “INSTALLATION.”
.
*
If the handset is moved to a point where the base and handset can no longer
communicate, you are “out of range.” When you try to make a call, the handset
will sound two short beeps to indicate that you are out of range.
.
Press any number button (0-9) for the memory location where the number
is to be stored.
If you receive a call while you are out of range, the handset might not ring—
6
You will hear a three-part tone that confirms the number was stored
or, if it does ring, the call might not connect when you press
closer to the base, then press to answer the call.
. Move
properly. If you hear a long buzzing tone, or nothing at all, press
then follow the steps above to store the number again.
,
If you move out of range during a phone conversation, you will hear noise or
interference. To improve reception, move closer to the base.
For example, to store 555-1234 in memory location 9: press
then press
,
,
,
.
If you move out of range without pressing
, the phone will be left “off
the hook.” To hang up, walk back into range, periodically pressing
until the PHONE light goes off.
NOTE: You may choose to store emergency numbers in memory
locations. The manufacturer assumes no responsibility for customer
reliance upon this feature.
*
Changing Channels
This cordless telephone has an advanced 25-channel AutoSelect feature that
minimizes the chance of interference. Every time you answer or make a call,
the AutoSelect feature searches for and selects a clear channel.
Storing a Pause in a Memory Number
If this phone is connected to a switchboard, you might have to dial an access
number (usually 9) to get an outside line. You can store the access number and
a pause in the dialing sequence; the pause allows the switchboard enough time
to get an outside line dial tone.
In the unlikely event that you hear noise or interference while using handset:
1
2
Press
.
If the interference does not clear, continue to press
a clear channel (your call will not be interrupted).
until you find
To insert a pause in a stored number:
When storing a number in memory, press and hold down the number button
that comes before the pause until you hear the second beep. This inserts a 1.5
second pause after that digit. If you hold the number button down longer, you
will hear more beeps as additional pauses are stored.
—OR—
Move closer to the base and press
.
NOTE: You must be in range to change channels.
NOTE: Each pause you store is counted as a digit. You can store up to 16
digits in each memory location.
*
*
For example, to store 9, PAUSE, 555-1234 in memory location 3: Press
, then hold down
,
until a second beep is heard. Then press
,
.
12
13
MEMORY
ANSWERING SYSTEM SET-UP
Dialing Memory Numbers
Turning the Answering System On/Off
The answering system must be on in order to use any answering system func-
tion. If the answering system is on, the Message Counter will be on (a steady
1
2
3
Press
Press
.
.
or flashing display). To turn the answering system on, press
on the
Press the number button (0-9) you assigned to the number you’re calling.
base. A voice message will announce “The machine is on.”
For example, to dial the number you assigned to button “6”: you would
press
To turn the answering system off, press
announce “The machine is off.”
again. A voice message will
,
,
.
Storing Numbers Just Dialed
Whenever you make a telephone call, you can store the number you dialed in
Announcements to Callers
Before using the answering system, you should record the announcement (up
to three minutes long) that callers will hear when the system answers a call.
memory. Press
instead of entering the telephone number when storing
memory numbers.
Pre-recorded Announcement
If you choose not to record an announcement, callers will hear “Hello. Please
Replacing a Stored Number
You can replace a stored number by simply storing a new number in its place.
leave a message after the tone.”
Memory Guard
Recording an Announcement
The phone numbers you store in memory are protected from loss when you
change the handset battery, or in the event of a power failure.
1
2
3
Prepare your announcement.
Press
Press
on the base (CH is displayed on the Message Counter).
. You will hear “Record the announcement after the tone.
Press STOP when you are done.”
4
5
6
The system begins to record after the tone. The Message Counter will
display the length of the announcement in seconds.
Speak in a normal voice, about nine inches from the microphone and avoid
background noise.
Press
when you are finished speaking.
The announcement plays back automatically. The Message Counter displays
AP (for Announcement Play).
If the announcement did not record successfully, you will hear an error tone
to indicate that you need to record again.
To review your announcement at any time press
.
Deleting an Announcement
1
2
Press
Press
to begin reviewing the announcement.
while the announcement is playing.
The system will beep once while the announcement is deleted.
14
15
ANSWERING SYSTEM SET-UP
ANSWERING SYSTEM SET-UP
To change either the ring select or remote access code, or both, you must first
access the feature set-up menu. Follow the instructions below:
Announcement Play/Silent
Your system is factory preset to audibly play your announcement through the
speaker when the system answers a call. If you do not want your announce-
ment to be audible during answering, you can change your system as follows
so that the announcement is not heard:
1
2
Press
Press
.
on the base. SU will be displayed on the Message Counter
and you will hear “To listen to settings, press SET UP,” followed by two
beeps.
1
2
3
Press and hold
for approximately two seconds and the current setting
(AP for Announcement Play) will be displayed on the Message Counter.
Continue to hold down the button until AS (for Announcement Silent) is
displayed and then release the button.
3
Press
again. The current ring select setting will be displayed and
you will hear “number of rings, X” (“X” being 1, 2, 3, 4, 5, 6, 7 or “Toll
Saver.”) This message will be followed by “To change the number of
rings or select Toll Saver, press SKIP or REPEAT.”
To change back to Announcement Play, simply repeat the above steps.
4
5
Press
When you hear the desired ring setting, press
You will hear “remote access code is XYZ.” If you do not wish to change
your code, simply press on the base to exit the feature set-up menu.
If you want to change your remote access code, then proceed as outlined
below.
(to go forward) or
(to go backward).
Setting the Clock
You’ll need to set the clock so that it can record the day and time that each
message is received.
.
1
2
3
Press
Press
. The Message Window displays CH.
. The current day setting is announced.
To change the day setting, hold down
until the correct day is announced. Then release the button.
Press . The current hour setting is announced.
To change the hour setting, hold down
until the correct hour is announced. Then release the button.
Press . The current minute setting is announced.
To change the minute setting, hold down
until the correct minute is announced. Then release the button.
Press . The new day and time are announced.
or
6
After you hear the remote access code number, you will hear “To select
the first digit, press SKIP or REPEAT, then SET UP.” Press
4
5
or
until you hear the single digit number
or
you want. (For the first digit in your code, your choices are numbers
between 5 and 9. For the second and third digits in your code, your choices
6
7
are numbers between 0 and 9.) Press
.
or
7
8
You will hear “Select the second digit, then press SET UP.”
8
Use the
or
buttons to select the desired
.
To check the clock, press
.
single digit second number, and then press
9
You will hear “Select the third digit, then press SET UP.”
Ring Select, Toll Saver and the Remote Access Code
10 Use
or
until you hear the desired single
.
The Ring Select is the number of times the phone rings before the system answers.
digit third number and then press
The settings are numbers 1-7, and Toll Saver. The preset ring select setting is 4.
11 You will hear “Remote access code is XYZ.”
12 Press to exit the feature set-up menu or press
ring select feature.
Toll Saver sets the system to answer calls on the second ring only if you have
new messages. If no new messages have been recorded, the system will answer
on the fourth ring.
to access the
This setting can be used when you will be calling from another location to
check for messages. If you have new messages (i.e., messages you have not
listened to yet), the system will answer after two rings. If there are no new
messages, the phone will ring at least three times before the system answers.
You can then hang up after the third ring to avoid paying long distance charges.
The Remote Access Code gives you access to your messages, memos and
announcements when you call in from another location. You can use the preset
code which is 500 or you can choose a new code between 500 and 999.
16
17
ANSWERING SYSTEM SET-UP
ANSWERING SYSTEM OPERATION: At the Base
Reviewing the Setting in the Feature Set-Up Menu
Answering Calls and Recording Messages
Press
and you will hear the following sequence of messages:
“Set-up review”
“Number of rings X”
When the system is ON and the phone begins ringing, the system will answer
the call at the number of rings specified in Ring Select. The caller hears the
announcement you recorded followed by a single beep. After the beep, the
system begins recording your caller’s message. While the system is taking a
call, “— —” will be displayed in the Message Counter. Recording continues
until 7 seconds of silence occurs or the maximum message time is reached, at
which point the system will stop recording, and the Message Counter display
will be increased by one.
1
2
3
4
5
“Remote access code is XYZ”
“End of review”
“To change a setting, press CHANGE, then SET UP”
If the system is OFF and the phone rings, the call will be answered after 10
rings and the caller will hear “The machine is off.” If the system is ON and
the memory is full, the call will also be answered after 10 rings. The caller will
hear “Memory is full.” Remote access commands to change the ON/OFF
status are explained in “ANSWERING SYSTEM OPERATION AWAY
FROM BASE.”
Volume Control
Press
or
on the base to adjust speaker volume, from 0 (lowest) to
7 (highest). If the volume setting is set to 7 and you press , or if it’s set 0
and you press ,you’ll hear a beep to let you know you’re already at the max-
imum or minimum setting.
Incoming Message Length
Screening and Intercepting Incoming Calls
The maximum length of an incoming message is three minutes. If a caller is
still talking after three minutes, they will hear a beep and the system will then
disconnect.
To screen calls, make sure you have set your system to an appropriate volume
level so you can hear the caller’s voice.
If you decide to take a call, press
on the handset and talk to the caller.
If you pick up an extension phone during the announcement and the
announcement does not stop right away, press and release the telephone
Memory Capacity
switchhook or press
.
The system can store approximately 12 minutes of messages, memos and
announcements (up to a maximum of 99 messages).
Listening to Your Messages
The number of messages recorded will be displayed in the Message Counter
window.
When memory is full, or the maximum number of messages is recorded, an F,
for full, will flash on and off in the Message Counter. Delete messages to make
room for new ones.
To play all your messages:
1
2
3
Press
on the base.
The system displays the number 1 and begins to play the first message.
If there are no messages, you will hear “No messages” and see the
Message Counter go blank.
18
19
ANSWERING SYSTEM OPERATION: At the Base
ANSWERING SYSTEM OPERATION: At the Base
To play only your new messages:
To make sure you are deleting the right message, you can press
to replay the message after listening to it, then press
while the message is playing.
1
2
Hold down
for about two seconds.
The system displays the number of the first new message and begins to
play that message.
After the system reaches the end of the last message, any messages that were
not deleted are renumbered, and the Message Counter shows the total number
of messages remaining.
3
If there are no new messages, you will hear “No new messages” and the
Message Counter will go blank.
To replay a deleted message:
At the beginning of each message, the system announces the day and time the
message was received. While the message is playing, the Message Counter
displays the number of the message. After the last message has been played,
the system announces “End of messages.”
•
Before the system announces “End of messages,” a deleted message can
be replayed by pressing until the number of the message
is displayed in the Message Counter. However, once the system announces
“End of messages,” a deleted message cannot be replayed.
The following options are available during playback:
To delete ALL messages:
•
•
•
To repeat an entire message, press
playing.
while the message is
1
2
Listen to all your messages.
To back up to an earlier message, repeatedly press
the number of that message is displayed.
until
Press and hold
. The system deletes the messages and you will
hear “Messages deleted.” The Message Counter will return to 0.
To repeat part of a message (review), hold down
seconds, then release it to resume playing. (The system chirps while the
button is held down.)
for a few
NOTE: This system has a safety feature that prevents you from
accidentally deleting new messages. If there are new messages among
those you are trying to delete, you will hear an error tone and none of your
messages will be deleted.
*
•
•
To skip ahead to a later message, press
.
To skip part of a message (cue), hold down
for a few
seconds, then release it to resume playing. (The system chirps while the
button is held down.)
Recording a Memo
You can record a memo through the microphone in the base and play it as if it
were an incoming message.
•
To stop playback, press
.
To record a memo:
Saving Messages
The system saves your messages automatically if you do not delete them.
1
2
3
Press
on the base.
You will hear a beep and 0 will display in the Message Counter.
Start speaking towards the microphone. The elapsed time of your memo
will show in seconds in the memory counter.
Deleting Messages
To delete a selected message:
4
Press
to stop recording.
•
Press
while the message you want to delete is being played and its
The system stores and treats your memo as a message.
message number is being displayed.
The system erases the message corresponding to the number shown in
the Message Counter, beeps once, and continues with the next message
(or announces “End of messages”).
Power Failures
With the MESSAGE GUARD Power Fail Protection System, your messages
and announcement will be saved even in the event of a power failure.
20
21
ANSWERING SYSTEM OPERATION:
Away from the Base
ANSWERING SYSTEM OPERATION:
Away from the Base
(Cordless Handset/Remote)
(Cordless Handset/Remote)
This cordless answering system allows you to retrieve messages and operate
other functions even when you are away from your home or office. In addition,
this answering system has the advantage of allowing you to access your
answering machine not only when you are away from your home or office,
but also when you are using the cordless handset anywhere in or around your
home or office (as long as you are within range of the base).
Accessing the Answering System from a
Touch Tone Phone
1
Dial your phone number.
NOTE: Remember that if you set the RING SELECT feature to TOLL
SAVER, the system will answer after two rings if there are new messages
and after four rings if there are no new messages. If you hear the third ring
you can hang up and save the cost of the call.
*
This system has been designed to make access to the answering system’s
features as easy as possible. Whether you are using the cordless handset or
calling from a touch tone phone outside your home, you press the same buttons
in the same order on either phone. The only difference between using the
cordless handset and another touch tone phone is making the initial contact
with the base answering system.
2
When the answering system answers and the outgoing announcement
begins to play, enter your three-digit remote access code.
The system will announce the number of messages you have (for example:
“You have three messages.”), and then beep twice to indicate that it is ready
to accept a command.
Once you have established contact with the answering system, you can perform
a series of operations.
If it does not receive any instructions in a few seconds, the system will auto-
matically play all of your messages. You can allow the system to play your
messages, or you can use the number buttons on the phone to direct the system
to perform any of the operations shown below:
Accessing the Answering System From the
Cordless Handset
If your Ringer Switch is set to ON, the ANS SYS light on the handset will
flash on and off to indicate you have new messages. To access the system,
Voice Help Menu
press
on the handset and wait for the ANS SYS light to go on. The
The Voice Help Menu allows you to use the answering system from your cord-
less handset or from a remote touch tone telephone even if you do not know or
remember the various command codes. Once you have established a connection
with the answering system (see “Accessing the Answering System from a
Touch Tone Phone”), the Voice Help Menu will guide you through all the other
codes you will need for full access.
system will announce the number of messages you have (for example: “You
have three messages.”) and then beep twice to indicate that it is ready to
accept a command.
If it does not receive any instructions in a few seconds, the system will
automatically play all of your messages. You can allow the system to play
your messages, or you can use the number buttons on the handset to direct the
system to perform other operations.
You can access the Voice Help Menu any time after the system has given you
the two-beep signal to indicate that it is ready to accept a command.
If you have no messages and the system receives no command within a
few seconds after announcing “You have no messages,” you will hear a
list of possible commands from the built-in Voice Help menu. See “Voice
Help Menu.”
Using the Voice Help Menu:
Press . The system will announce a list of operations and the buttons you
need to press to activate them.
To end the connection from the cordless handset, press
handset to the base.
, or return the
At the end of the menu list, the system will beep twice to indicate that it is
ready to accept a command. If you have heard the number for the function you
want, simply press that number button.
22
23
ANSWERING SYSTEM OPERATION:
Away from the Base
ANSWERING SYSTEM OPERATION:
Away from the Base
(Cordless Handset/Remote)
(Cordless Handset/Remote)
Deleting selected messages:
Remote Access Commands
To delete only a selected message, press
be sure you delete the right message, you must press
indicates the end of the message.
while the message is playing. To
Playing all of your messages:
before the beep that
Press
. The system will play all of your messages and then beep twice to
indicate that it is ready to accept a new command.
If necessary, you can press
to replay the message after listening to it, then
press
when you are sure you are deleting the right message.
Playing new messages only:
Press
. The system will play only those messages recorded since the last
Deleting all messages:
time messages were checked, and then it will beep twice to indicate that it is
ready to accept a new command.
Listen to all messages. Press and release
twice to indicate that it is ready to accept a new command.
,
. The system will then beep
Saving messages:
Ring Select and the Remote Access Code
This system automatically saves messages after playback, unless you command
it to delete messages. After performing any answering system operation,
simply hang up the phone.
You can also review and change the remote access code and the ring select
from another touch tone phone (or the handset).
You can work with these features any time after the system has given you the
two-beep signal to indicate that it is ready to accept a command.
Repeating a message:
Press
. The system will stop playing, return to the beginning of the current
Reviewing your ring select and remote access code settings:
message, and then resume playing. Each time you press and release
system will back up one more message.
, the
Press
. The system will announce the current settings then beep twice to
indicate that it is ready to accept a command.
If you are calling from a touch tone phone which generates a continuous
touch tone when you hold down a button, you can repeat part of a message by
pressing and holding down . Release it to resume playing.
To change settings:
1
Press
You will hear “To listen to settings, press 9” followed by
two beeps.
Skipping a message:
2
Press
. The current ring select setting will be displayed and you will
Press . The system will stop playing, advance to the beginning of the next
message, and resume playing. Each time you press , the system will advance
one more message.
hear “Number of rings, X” (“X” being 1, 2, 3, 4, 5, 6, 7 or “Toll Saver”).
This message will be followed by “To change the number of rings or
select toll saver, press 6 or 4.”
If you are calling from a touch tone phone which generates a continuous touch
tone when you hold down a button, you can skip part of a message by pressing
and holding down . Release it to resume playing.
3
Press
to go forward or
to go backward. When you hear the desired
ring setting, press
.
4
5
You will hear “Remote access code is XYZ.”
Stop playback:
After you hear the remote access code number, you will hear “To select
the first digit, press 6 or 4 then press 9.”
Press
.
6
7
Press
or
until you hear the single digit number you want. Press
.
You will hear “Select the second digit then press 9.”
24
25
ANSWERING SYSTEM OPERATION:
Away from the Base
ANSWERING SYSTEM OPERATION:
Away from the Base
(Cordless Handset/Remote)
(Cordless Handset/Remote)
Recording a Memo
From another touch tone phone (or the handset), you can also record a memo
for yourself or anyone else who has access to the system. When the system
plays messages, it plays the memo along with the other messages on the system.
8
9
Press
press
or
.
to select the desired single digit second number, then
You will hear “Select the third digit then press 9.”
or until you hear the desired single digit third number, and
then press
11 You will hear “Remote access code is XYZ”.
12 Press to exit the feature set-up menu. You will hear “End of set-up”
and the system will beep twice to indicate that it is ready to accept a
10 Press
You can record a memo any time after the system has given you the two-beep
signal to indicate that it is ready to accept a command.
.
1
2
3
4
Press
.
The system will beep to signal that it is ready to record.
Speak into the phone in a normal tone of voice.
command.
To stop recording, press
.
The memo is counted as a new message.
The Outgoing Announcement
You can also review and change your outgoing announcement from another
touch tone phone (or the handset).
The Clock
You can also review and change the day and time setting on your clock from
another touch tone phone (or the handset).
You can work with your outgoing announcement any time after the system has
given you the two-beep signal to indicate that it is ready to accept a command.
You can work with the clock setting any time after the system has given you
the two-beep signal to indicate that it is ready to accept a command.
Reviewing your outgoing announcement:
Press
. The system will play your outgoing announcement, and beep twice
Reviewing the day/time setting:
to indicate that it is ready to accept a command.
Press
. The answering system will announce the current day/time setting
Changing your outgoing announcement:
and beep twice to indicate that it is ready to accept a command.
1
2
Press
. The system will beep to signal that it is ready to record.
Changing the day/time setting:
Record your new announcement by speaking into the phone in a normal
tone of voice.
1
Press
. You will hear the current day setting followed by “To
change, press 6 or 4. To change the hour, press 8.”
3
Press
when you are done. The system will beep and begin to play back
2
To set day:
your new announcement. At the end of the new announcement, the system
will beep twice to indicate that it is ready to accept a command.
Press
to move the setting to a day earlier in the week, or
to move
the setting to a day later in the week. Each time you press one of these
buttons, the system will announce the day. When you hear the correct day,
go on to set the hour.
3
To set hour:
Press
“To change press 6 or 4. To change the minutes, press 8.” Press
or to move the hour setting down or up. Each time you press one
. The system will announce the current hour setting followed by
of these buttons, the system will announce the hour. When you hear the
correct hour, go on to set minutes.
26
27
ANSWERING SYSTEM OPERATION:
Away from the Base
ANSWERING SYSTEM OPERATION:
Away from the Base
(Cordless Handset/Remote)
(Cordless Handset/Remote)
4
To set minutes:
Call Monitoring
Press
. The system will announce the current minute setting followed
As calls come in, the answering system will answer and record messages as
long as it is set for automatic answering operation. You can use the cordless
handset to listen to the callers as they leave messages. You can begin to speak
by “To change, press 6 or 4. Press 8 when you are done.”
Press
press one of these buttons, the system will announce the minute. When
you hear the correct minute, press . The system will announce the new
or
to move the minute setting down or up. Each time you
to a caller directly if you wish by pressing
.
day/time setting and beep twice to indicate that it is ready to accept a
command.
Monitoring calls:
1
If the handset is away from the base, press
ANS SYS light to go on.
and wait for the
or return the
Remote On/Off
You can also turn your system on or off from another touch tone phone
(or the handset).
2
To end monitoring without answering the call, press
handset to the base.
Announcement Bypass
To review on/off status:
Press
. You will hear “The machine is on” or “The machine is off.” The
You can instruct frequent callers who use touch tone phones to press
they hear your announcement. The system will stop playing the announcement
and beep so that the caller can immediately begin recording a message.
when
system will beep twice to indicate that it is ready to accept a command.
To change the status from off to on:
Even if the system is off, it will answer a call after 10 rings (provided it is
connected to AC power) and announce “The machine is off” and will beep
AUDIBLE SIGNALS
twice to indicate it is ready to accept a command. Press
. The system
will announce “The machine is on” and beep twice to indicate it is ready for a
new command.
The following is a list of the system’s audible signals and their meaning.
To change the status from on to off:
Sound
Meaning
Press
. The system will announce “The machine is off” and beep
Long ringing
Incoming call
twice to indicate it is ready for a new command.
Single beep
A valid button has been pressed
Page
Three-part tone
Repeating three-part tone
Two short beeps
Four short beeps
Four long beeps
Long buzzing tone
Series of ascending tones
Recording a Message When the System is Off
If the system is off, you can still leave a message by pressing
handset or another touch tone phone (once the system answers after 10 rings). The
system will turn on, beep to signal “begin recording” and record your message.
Handset locator
from the
Handset is out of range of base
Low battery
Base busy
To Exit Remote Access
If you are using another touch tone phone or the handset, simply hang up at
any time during remote access. If you are using the handset, pressing
will cause the system to exit remote access.
Error (action has been unsuccessful)
Action has been successful
28
29
BATTERIES
IN CASE OF DIFFICULTY
If you have difficulty operating this phone, try the suggestions below. If you
still have trouble, call 1 800 722-9125.
Charging the Handset Battery Pack
The batteries need charging when:
If the phone does not work at all, check these items first
•
•
The phone beeps four times when you press
.
•
•
Make sure the power cord is plugged into the base and an electrical outlet.
The MUTE/LOW BATT light on the handset is on when the phone is off.
The MUTE/LOW BATT light on the handset flashes on and off when the
phone is on.
Make sure the telephone line cord is plugged firmly into the base unit and
the telephone jack.
•
If the phone does not beep or beeps four times when you press
batteries might need recharging.
, the
•
The phone does not respond when you press
and no lights go on.
Place the handset in the base so the CHARGING light goes on. The batteries
will be fully charged in 10 hours. Once the batteries are fully charged, you
need only put the handset in the base when the LOW BATT light flashes.
•
•
•
If the LOW BATT light is flashing, the batteries need recharging.
Make sure the battery pack is installed correctly.
If it is more convenient for you, you can leave the handset in the base all the
time. It is impossible to overcharge the batteries.
If the battery pack will still not charge, replace it with Replacement
Battery 4051.
If you get a low-battery signal even after 10 hours of charging, the battery
should be replaced.
•
If the above suggestions do not solve the problem, try resetting the
security code, as described below.
■
Place the handset in the base, and check to make sure the CHARGING
CAUTION: To reduce the risk of fire or injury to persons or
damage to the telephone, read and follow these instructions carefully.
light is on. Wait 15 seconds, then pick up the handset and press
The phone should operate properly. If it does not, try the next step.
.
•
•
•
Use only Replacement Battery 4051.
■
Place the handset in the base, and check to make sure the CHARGING
light is on. Unplug the AC adapter from the outlet, wait 15 seconds,
then plug it in again. The CHARGING light should go on. Wait
Do not dispose of the battery in a fire. The cell might explode.
Do not open, puncture or mutilate the battery. Released electrolyte is
corrosive and might cause damage to the eyes or skin. It might be toxic if
swallowed.
another 15 seconds, then pick up the handset and press
. The
phone should operate properly. If it does not, try the next step.
■
Pick up the handset, open the battery compartment, and unplug the
battery pack. Wait 15 seconds, then reinstall the battery pack, close the
battery compartment, place the handset in the base. The CHARGING
light should go on. Wait another 15 seconds, then pick up the handset
Replacing the Battery Pack
1
Remove the battery compartment cover on the handset by pressing on the
indentation and sliding the cover downward.
and press
. The phone should operate properly.
2
3
Lift out the old battery pack and unplug it from the handset.
If you hear a two-beep signal when you try to use the handset
Hold the new battery pack and plug the cord into the handset. Place
the battery pack in the compartment so the cords rest on top of the
battery pack.
•
•
The handset and base are not communicating properly. You might be out of
range while attempting to dial. Move closer to the base and try the call again.
If moving closer to the base does not help, the handset and base might be
set to different security codes. To reset the security code, as described in
the previous section.
4
5
Replace the cover by sliding it on its track up over the battery
compartment until it snaps firmly in place.
The new batteries must be charged before using this telephone. Place
the handset in the base unit and allow it to charge for 10 hours. The
telephone may operate before that, but, for best performance, let the
batteries charge fully.
If you have no dial tone, check all the previous suggestions. If you still do not
hear a dial tone, disconnect the phone and try another phone in the same jack.
If there is no dial tone on that phone either, the problem is probably in your
wiring or local service. Call your local telephone service company.
30
31
IN CASE OF DIFFICULTY
IN CASE OF DIFFICULTY
If you hear noise or interference when using the phone
If this answering system does not work properly, try the following suggestions
before seeking repair assistance.
•
•
You may be out of range. Move closer to the base.
Press
to change to another of the 25 channels available. If the noise
If messages are incomplete
is exceptionally loud, move closer to the base before changing channels.
•
•
•
If a caller leaves a very long message, part of it may be lost when the
system disconnects the call after three minutes.
If the caller pauses for more than seven seconds, the system stops
recording and disconnects the call.
If the system’s memory becomes full during a message, the system stops
recording and disconnects the call.
•
•
Household appliances plugged into the same circuit as the base can
sometimes cause interference. Try moving the appliance or the base to
another outlet.
The layout of your home or office may be limiting the operating range.
Try moving the base to another location, preferably on an upper floor.
If you have difficulty hearing messages
Check the VOLUME setting.
If the phone does not ring when you receive a call
•
•
Make sure the handset ringer switch is set to ON.
If the system does not answer after correct number of rings
Make sure the telephone line cord is connected firmly to the base and the
telephone jack. Make sure the power cord is plugged into an outlet not
controlled by a wall switch.
•
•
•
•
Make sure that the two-digit message counter in the base is on. If it is off,
press
If TOLL SAVER is on, the number of rings changes from four to two
when you have new messages waiting. See “Ring Select.”
In some cases, the system may be affected by the ringing system used by
the local telephone company.
.
•
•
You might be too far from the base. Move closer to the base.
You might have too many extension phones on your telephone line to
allow all of them to ring. Try unplugging some of the other phones.
If the memory is full or the system is off, the system answers after
10 rings.
If you hear other calls while using the phone
•
•
Press
to change to another channel.
If CL appears in Message Counter
If the clock stops running because of a power failure, CL blinks in the Message
Counter to indicate that the clock should be reset. See “Setting the Clock.”
Disconnect the base from the telephone jack, and plug in a corded
telephone. If you still hear other calls, the problem is probably in your
wiring or local service. Call your local phone company.
If the system does not respond to remote commands from a remote
touch tone phone
If your telephone misdials or you don’t hear the other person right away
•
It might take a few seconds for your handset to find a good connection to
the phone system. While it is searching, the PHONE light blinks rapidly.
Do not start dialing until the PHONE light is on steadily.
•
Make sure you are calling from a touch tone phone. When you dial a
number, you should hear tones. If you hear clicks instead, the phone is not
a touch tone telephone.
•
•
If you have dial pulse (rotary) service, you’ll need to set the dial mode.
•
The answering system may not detect the Remote Access Code while your
announcement is playing. Try waiting until the announcement is over
before entering the code.
Make sure you enter your Remote Access Code correctly.
There may be noise or interference on the phone line you are using. Press
keys firmly.
Press
.
If you have TONE service and you hear strange clicks while you are dial-
ing, you’ll need to set the dial mode. Press
•
•
.
If you hear noise in the handset and the buttons don’t work
The base unit and handset might not be set to the same security code. Place the
handset in the base for at least 15 seconds to reset the security code.
32
33
AT&T 7625 WC_1ATT 7/28/98 11:30 PM Page 1
2
Cordless Digital Answering System
Telephone 7625
Answering System Operation
From a Remote Touch Tone Phone
1
2
3
Dial your telephone number.
NOTE: Remember that if the system was
set to TOLL SAVER, it will answer after
two rings if there are new messages and after
four rings if there are no new messages.
When the system answers, enter your
3-digit remote access code. The system
announces the number of messages you
have, then beeps twice and is ready to
accept a command.
Enter a command (see other side)
Your Remote Access Code _____________.
(The preset code is 500.)
©1998 Philips Consumer Communications L.P.
All rights reserved. Printed in Mexico.
848232930 Issue 1AT&T
2
Cordless Digital Answering System
Telephone 7625
Answering System Operation
From a Remote Touch Tone Phone
1
2
3
Dial your telephone number.
NOTE: Remember that if the system was
set to TOLL SAVER, it will answer after
two rings if there are new messages and after
four rings if there are no new messages.
When the system answers, enter your
3-digit remote access code. The system
announces the number of messages you
have, then beeps twice and is ready to
accept a command.
Enter a command (see other side)
Your Remote Access Code _____________.
(The preset code is 500.)
©1998 Philips Consumer Communications L.P.
All rights reserved. Printed in Mexico.
848232930 Issue 1AT&T
AT&T 7625 WC_1ATT 7/28/98 11:30 PM Page 2
Play all messages
Play new messages only
Save messages
Hang up
,
Delete message being played
Delete all messages
Repeat
Stop playback
Skip a message
Review announcement
Change announcement
, after beep, press
to end
Review day/time setting
Change day/time setting
Review ring select and
remote access code settings
Change ring select and
remote access code
Review on/off status
Change on/off status
Voice Help Menu
any time you hear 2 beeps
Play all messages
Play new messages only
Save messages
Hang up
,
Delete message being played
Delete all messages
Repeat
Stop playback
Skip a message
Review announcement
Change announcement
, after beep, press
to end
Review day/time setting
Change day/time setting
Review ring select and
remote access code settings
Change ring select and
remote access code
Review on/off status
Change on/off status
Voice Help Menu
any time you hear 2 beeps
|