ARM Cortex r1p3 User Manual

Cortex -R4 and Cortex-R4F  
Revision: r1p3  
Technical Reference Manual  
Copyright © 2009 ARM Limited. All rights reserved.  
ARM DDI 0363E (ID013010)  
Contents  
Cortex-R4 and Cortex-R4F Technical Reference  
Manual  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
iii  
Contents  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
iv  
Contents  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
v
List of Tables  
Cortex-R4 and Cortex-R4F Technical Reference  
Manual  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
vii  
List of Tables  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
viii  
List of Tables  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
ix  
List of Tables  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
x
List of Tables  
Table 14-17  
Cycle timing behavior of Load and Store Multiples, other than load multiples including the PC .......  
14-21  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
xi  
List of Figures  
Cortex-R4 and Cortex-R4F Technical Reference  
Manual  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
xiii  
List of Figures  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
xiv  
List of Figures  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
xv  
Preface  
This preface introduces the Cortex-R4 and Cortex-R4F Technical Reference Manual. It contains  
the following sections:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
xvi  
 
Preface  
About this book  
This is the Technical Reference Manual (TRM) for the Cortex-R4 and Cortex-R4F processors.  
In this book the generic term processor means both the Cortex-R4 and Cortex-R4F processors.  
Any differences between the two processors are described where necessary.  
Note  
The Cortex-R4F processor is a Cortex-R4 processor that includes the optional Floating Point  
Unit (FPU) extension, see Product revision information on page 1-24 for more information.  
In this book, references to the Cortex-R4 processor also apply to the Cortex-R4F processor,  
unless the context makes it clear that this is not the case.  
Product revision status  
The rnpn identifier indicates the revision status of the product described in this book, where:  
rn  
Identifies the major revision of the product.  
pn  
Identifies the minor revision or modification status of the product.  
Intended audience  
Using this book  
This book is written for system designers, system integrators, and programmers who are  
designing or programming a System-on-Chip (SoC) that uses the processor.  
This book is organized into the following chapters:  
Read this for an introduction to the processor and descriptions of the major  
functional blocks.  
Read this for a description of the processor registers and programming  
information.  
Read this for a description of clocking and resetting the processor, and the steps  
that the software must take to initialize the processor after reset.  
Read this for a description of the system control coprocessor registers and  
programming information.  
Read this for a description of the functions of the Prefetch Unit (PFU), including  
dynamic branch prediction and the return stack.  
Read this for a description of the Performance Monitoring Unit (PMU) and the  
event bus.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
xvii  
   
Preface  
Read this for a description of the Memory Protection Unit (MPU) and the access  
permissions process.  
Read this for a description of the Level One (L1) memory system.  
Read this for a description of the power control facilities.  
Read this for a description of the debug support.  
Read this for a description of the Floating Point Unit (FPU) support in the  
Cortex-R4F processor.  
Read this for a description of the Integration Test Registers, and of integration  
testing of the processor with an ETM-R4 trace macrocell.  
Read this for a description of the timing parameters applicable to the processor.  
Read this for a description of the instruction cycle timing and instruction  
interlocks.  
Read this for a description of the inputs and outputs of the processor.  
Read this for a description of how to select the Error Checking and Correction  
(ECC) scheme depending on the Tightly-Coupled Memory (TCM) configuration.  
Read this for a description of the technical changes between released issues of this  
book.  
Read this for definitions of terms used in this guide.  
Conventions  
Conventions that this book can use are described in:  
Typographical  
The typographical conventions are:  
italic  
Highlights important notes, introduces special terminology, denotes  
internal cross-references, and citations.  
bold  
Highlights interface elements, such as menu names. Denotes signal  
names. Also used for terms in descriptive lists, where appropriate.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
xviii  
 
Preface  
monospace  
Denotes text that you can enter at the keyboard, such as commands, file  
and program names, and source code.  
monospace  
Denotes a permitted abbreviation for a command or option. You can enter  
the underlined text instead of the full command or option name.  
monospace italic  
Denotes arguments to monospace text where the argument is to be  
replaced by a specific value.  
monospace bold  
Denotes language keywords when used outside example code.  
< and >  
Enclose replaceable terms for assembler syntax where they appear in code  
or code fragments. For example:  
MRC p15, 0 <Rd>, <CRn>, <CRm>, <Opcode_2>  
Timing diagrams  
The figure named Key to timing diagram conventions explains the components used in timing  
diagrams. Variations, when they occur, have clear labels. You must not assume any timing  
information that is not explicit in the diagrams.  
Shaded bus and signal areas are undefined, so the bus or signal can assume any value within the  
shaded area at that time. The actual level is unimportant and does not affect normal operation.  
Clock  
HIGH to LOW  
Transient  
HIGH/LOW to HIGH  
Bus stable  
Bus to high impedance  
Bus change  
High impedance to stable bus  
Key to timing diagram conventions  
Signals  
The signal conventions are:  
Signal level  
The level of an asserted signal depends on whether the signal is  
active-HIGH or active-LOW. Asserted means:  
HIGH for active-HIGH signals  
LOW for active-LOW signals.  
Lower-case n  
Prefix A  
At the start or end of a signal name denotes an active-LOW signal.  
Denotes global Advanced eXtensible Interface (AXI) signals.  
Denotes AXI read address channel signals.  
Prefix AR  
Prefix AW  
Prefix B  
Denotes AXI write address channel signals.  
Denotes AXI write response channel signals.  
Prefix P  
Denotes Advanced Peripheral Bus (APB) signals.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
xix  
       
Preface  
Prefix R  
Prefix W  
Denotes AXI read data channel signals.  
Denotes AXI write data channel signals.  
Further reading  
This section lists publications by ARM and by third parties.  
See http://infocenter.arm.comfor access to ARM documentation.  
ARM publications  
This book contains information that is specific to the processor. See the following documents  
for other relevant information:  
AMBA® AXI Protocol Specification (ARM IHI 0022)  
AMBA 3 APB Protocol Specification (ARM IHI 0024)  
ARM Architecture Reference Manual, ARMv7-A and ARMv7-R edition (ARM DDI 0406)  
ARM PrimeCell® Vectored Interrupt Controller (PL192) Technical Reference Manual  
(ARM DDI 0273)  
Cortex-R4 and Cortex-R4F Integration Manual (ARM DII 0130)  
Cortex-R4 and Cortex-R4F Configuration and Sign-off Guide (ARM DII 0185)  
CoreSightDAP-Lite Technical Reference Manual (ARM DDI 0316)  
CoreSight ETM-R4 Technical Reference Manual (ARM DII 0367)  
RealViewCompilation Tools Developer Guide (ARM DUI 0203)  
Application Note 98, VFP Support Code (ARM DAI 0098)  
Application Note 204, Understanding processor memory types and access ordering  
(ARM DAI 0204).  
Other publications  
This section lists relevant documents published by third parties:  
ANSI/IEEE Std 754-1985, IEEE Standard for Binary Floating-Point Arithmetic  
JEP106M, Standard Manufactures Identification Code, JEDEC Solid State Technology  
Association.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
xx  
 
Preface  
Feedback  
ARM welcomes feedback on this product and its documentation.  
Feedback on this product  
If you have any comments or suggestions about this product, contact your supplier and give:  
The product name.  
The product revision or version.  
An explanation with as much information as you can provide. Include symptoms if  
appropriate.  
Feedback on this book  
If you have any comments on this book, send an e-mail to [email protected]. Give:  
the title  
the number  
the relevant page number(s) to which your comments apply  
a concise explanation of your comments.  
ARM also welcomes general suggestions for additions and improvements.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
xxi  
   
Chapter 1  
Introduction  
This chapter introduces the processor and its features. It contains the following sections:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
1-1  
   
Introduction  
1.1  
About the processor  
The processor is a mid-range CPU for use in deeply-embedded systems.  
The features of the processor include:  
An integer unit with integral EmbeddedICE-RT logic.  
High-speed Advanced Microprocessor Bus Architecture (AMBA) Advanced eXtensible  
Interfaces (AXI) for Level two (L2) master and slave interfaces.  
Dynamic branch prediction with a global history buffer, and a 4-entry return stack.  
Low interrupt latency.  
Non-maskable interrupt.  
Optional Floating Point Unit (FPU). The Cortex-R4F processor is a Cortex-R4 processor  
that includes the FPU.  
A Harvard Level one (L1) memory system with:  
optional Tightly-Coupled Memory (TCM) interfaces with support for error  
correction or parity checking memories  
optional caches with support for optional error correction schemes  
optional ARMv7-R architecture Memory Protection Unit (MPU)  
optional parity and Error Checking and Correction (ECC) on all RAM blocks.  
The ability to implement and use redundant core logic, for example, in fault detection.  
An L2 memory interface:  
single 64-bit master AXI interface  
64-bit slave AXI interface to TCM RAM blocks and cache RAM blocks.  
A debug interface to a CoreSight Debug Access Port (DAP).  
A trace interface to a CoreSight ETM-R4.  
A Performance Monitoring Unit (PMU).  
A Vectored Interrupt Controller (VIC) port.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
1-2  
   
Introduction  
1.2  
About the architecture  
The processor implements the ARMv7-R architecture and ARMv7 debug architecture. In  
addition, the Cortex-R4F processor implements the VFPv3-D16 architecture. This includes the  
VFPv3 instruction set.  
The ARMv7-R architecture provides 32-bit ARM and 16-bit and 32-bit Thumb instruction sets,  
including a range of Single Instruction, Multiple-Data (SIMD) Digital Signal Processing (DSP)  
instructions that operate on 16-bit or 8-bit data values in 32-bit registers.  
See the ARM Architecture Reference Manual, ARMv7-A and ARMv7-R edition for more  
information on the:  
ARM instruction set and Thumb instruction set  
ARMv7 debug architecture  
VFPv3 instruction set.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
1-3  
   
Introduction  
1.3  
Components of the processor  
This section describes the main components of the processor:  
Figure 1-1 shows the structure of the processor.  
ETM  
Debug  
Processor  
ETM  
interface  
Debug  
interface  
Data  
Processing  
Unit  
Load/Store  
Unit  
Prefetch Unit  
Level one memory system  
L1  
Memory  
Protection  
Unit  
L1  
instruction  
cache control  
data cache  
control  
Tightly-  
Coupled  
Memory  
(TCM)  
ATCM  
B1TCM  
B0TCM  
L1  
L1  
data  
cache RAM  
interface  
instruction  
cache RAM  
Level two interface  
L2 interface  
AXI  
slave port  
L2 interface  
AXI  
master port  
AXI slave bus  
AXI master bus  
Figure 1-1 Processor block diagram  
The PreFetch Unit (PFU) fetches instructions from the memory system, predicts branches, and  
passes instructions to the Data Processing Unit (DPU). The DPU executes all instructions and  
uses the Load/Store Unit (LSU) for data memory transfers. The PFU and LSU interface to the  
L1 memory system that contains L1 instruction and data caches and an interface to a L2 system.  
The L1 memory can also contain optional TCM interfaces.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
1-4  
       
Introduction  
1.3.1  
Data Processing Unit  
The DPU holds most of the program-visible state of the processor, such as general-purpose  
registers, status registers and control registers. It decodes and executes instructions, operating  
on data held in the registers in accordance with the ARM Architecture. Instructions are fed to  
the DPU from the PFU through a buffer. The DPU performs instructions that require data to be  
transferred to or from the memory system by interfacing to the LSU. See Chapter 2  
Programmers Model for more information.  
Floating Point Unit  
The Floating Point Unit (FPU) is an optional part of the DPU which includes the VFP register  
file and status registers. It performs floating-point operations on the data held in the VFP register  
1.3.2  
1.3.3  
Load/store unit  
Prefetch unit  
The LSU manages all load and store operations, interfacing with the DPU to the TCMs, caches,  
and L2 memory interfaces.  
The PFU obtains instructions from the instruction cache, the TCMs, or from external memory  
and predicts the outcome of branches in the instruction stream. See Chapter 5 Prefetch Unit for  
more information.  
Branch prediction  
The branch predictor is a global type that uses history registers and a 256-entry pattern history  
table.  
Return stack  
The PFU includes a 4-entry return stack to accelerate returns from procedure calls. For each  
procedure call, the return address is pushed onto a hardware stack. When a procedure return is  
recognized, the address held in the return stack is popped, and the prefetch unit uses it as the  
predicted return address.  
1.3.4  
L1 memory system  
The processor L1 memory system includes the following features:  
separate instruction and data caches  
flexible TCM interfaces  
64-bit datapaths throughout the memory system  
MPU that supports configurable memory region sizes  
export of memory attributes for L2 memory system  
parity or ECC supported on local memories.  
For more information of the blocks in the L1 memory system, see:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
1-5  
       
Introduction  
Instruction and data caches  
You can configure the processor to include separate instruction and data caches. The caches  
have the following features:  
Support for independent configuration of the instruction and data cache sizes between  
4KB and 64KB.  
Pseudo-random cache replacement policy.  
8-word cache line length. Cache lines can be either write-back or write-through,  
determined by MPU region.  
Ability to disable each cache independently.  
Streaming of sequential data from LDMand LDRDoperations, and sequential instruction  
fetches.  
Critical word first filling of the cache on a cache miss.  
Implementation of all the cache RAM blocks and the associated tag and valid RAM  
blocks using standard ASIC RAM compilers  
Parity or ECC supported on local memories.  
Memory Protection Unit  
An optional MPU provides memory attributes for embedded control applications. You can  
configure the MPU to have eight or twelve regions, each with a minimum resolution of 32 bytes.  
MPU regions can overlap, and the highest numbered region has the highest priority.  
The MPU checks for protection and memory attributes, and some of these can be passed to an  
external L2 memory system.  
For more information, see Chapter 7 Memory Protection Unit.  
TCM interfaces  
Because some applications might not respond well to caching, there are two TCM interfaces that  
permit connection to configurable memory blocks of Tightly-Coupled Memory (ATCM and  
BTCM). These ensure high-speed access to code or data. As an option, the BTCM can have two  
memory ports for increased bandwidth.  
An ATCM typically holds interrupt or exception code that must be accessed at high speed,  
without any potential delay resulting from a cache miss.  
A BTCM typically holds a block of data for intensive processing, such as audio or video  
processing.  
You can individually configure the TCM blocks at any naturally aligned address in the memory  
map. Permissible TCM block sizes are:  
0KB  
4KB  
8KB  
16KB  
32KB  
64KB  
128KB  
256KB  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
1-6  
     
Introduction  
512KB  
1MB  
2MB  
4MB  
8MB.  
The TCMs are external to the processor. This provides flexibility in optimizing the TCM  
subsystem for performance, power, and RAM type. The INITRAMA and INITRAMB pins  
enable booting from the ATCM or BTCM, respectively. Both the ATCM and BTCM support  
wait states.  
For more information, see Chapter 8 Level One Memory System.  
Error correction and detection  
To increase the tolerance of the system to soft memory faults, you can configure the caches for  
either:  
parity generation and error correction/detection  
ECC code generation, single-bit error correction, and two-bit error detection.  
Similarly, you can configure the TCM interfaces for:  
parity generation and error detection  
ECC code generation, single-bit error correction, and two-bit error detection.  
For more information, see Chapter 8 Level One Memory System.  
L2 AXI interfaces  
1.3.5  
The L2 AXI interfaces enable the L1 memory system to have access to peripherals and to  
external memory using an AXI master and AXI slave port.  
AXI master interface  
The AXI master interface provides a high bandwidth interface to second level caches, on-chip  
RAM, peripherals, and interfaces to external memory. It consists of a single AXI port with a  
64-bit read channel and a 64-bit write channel for instruction and data fetches.  
The AXI master can run at the same frequency as the processor, or at a lower synchronous  
frequency. If asynchronous clocking is required an external asynchronous AXI slice is required.  
AXI slave interface  
The AXI slave interface enables AXI masters, including the AXI master port of the processor,  
to access data and instruction cache RAMs and TCMs on the AXI system bus. You can use this  
for DMA into and out of the TCM RAMs and for software test of the TCM and cache RAMs.  
The slave interface can run at the same frequency as the processor or at a lower, synchronous  
frequency. If asynchronous clocking is required an external asynchronous AXI slice is required.  
Bits in the Auxiliary Control Register and Slave Port Control Register can control access to the  
AXI slave. Access to the TCM RAMs can be granted to any master, to only privileged masters,  
or completely disabled. Access to the cache RAMs can be separately controlled in a similar way.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
1-7  
   
Introduction  
1.3.6  
Debug  
The processor has a CoreSight compliant Advanced Peripheral Bus version 3 (APBv3) debug  
interface. This permits system access to debug resources, for example, the setting of  
watchpoints and breakpoints.  
The processor provides extensive support for real-time debug and performance profiling.  
The following sections give an overview of debug:  
System performance monitoring  
This is a group of counters that you can configure to monitor the operation of the processor and  
memory system. For more information, see About the PMU on page 6-6.  
ETM interface  
The Embedded Trace Macrocell (ETM) interface enables you to connect an external ETM unit  
to the processor for real-time code tracing of the core in an embedded system.  
The ETM interface collects various processor signals and drives these signals from the  
processor. The interface is unidirectional and runs at the full speed of the processor. The ETM  
interface connects directly to the external ETM unit without any additional glue logic. You can  
disable the ETM interface for power saving. For more information, see the CoreSight ETM-R4  
Technical Reference Manual.  
Real-time debug facilities  
The processor contains an EmbeddedICE-RT logic unit to provide real-time debug facilities. It  
has:  
up to eight breakpoints  
up to eight watchpoints  
a Debug Communications Channel (DCC).  
Note  
The number of breakpoints and watchpoints is configured during implementation, see  
The EmbeddedICE-RT logic monitors the internal address and data buses. You access the  
EmbeddedICE-RT logic through a memory-mapped APB interface.  
The processor implements the ARMv7 Debug architecture, including the extensions of the  
architecture to support CoreSight.  
To get full access to the processor debug capability, you can access the debug register map  
through the APBv3 slave port. See Chapter 11 Debug for more information on debug.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
1-8  
       
Introduction  
The EmbeddedICE-RT logic supports two modes of debug operation:  
Halt mode On a debug event, such as a breakpoint or watchpoint, the debug logic stops the  
processor and forces it into debug state. This enables you to examine the internal  
state of the processor, and the external state of the system, independently from  
other system activity. When the debugging process completes, the processor and  
system state are restored, and normal program execution resumes.  
Monitor debug mode  
On a debug event, the processor generates a debug exception instead of entering  
debug state, as in halt mode. The exception entry enables a debug monitor  
program to debug the processor while enabling critical interrupt service routines  
to operate on the processor. The debug monitor program can communicate with  
the debug host over the DCC or any other communications interface in the  
system.  
1.3.7  
1.3.8  
System control coprocessor  
The system control coprocessor provides configuration and control of the memory system and  
its associated functionality. Other system-level operations, such as memory barrier instructions,  
are also managed through the system control coprocessor.  
Interrupt handling  
Interrupt handling in the processor is compatible with previous ARM architectures, but has  
several additional features to improve interrupt performance for real-time applications.  
VIC port  
The core has a dedicated port that enables an external interrupt controller, such as the ARM  
PrimeCell Vectored Interrupt Controller (VIC), to supply a vector address along with an  
Interrupt Request (IRQ) signal. This provides faster interrupt entry, but you can disable it for  
compatibility with earlier interrupt controllers.  
Note  
If you do not have a VIC in your design, you must ensure the nIRQ and nFIQ signals are  
asserted, held LOW, and remain LOW until the exception handler clears them.  
Low interrupt latency  
On receipt of an interrupt, the processor abandons any pending restartable memory operations.  
Restartable memory operations are the multiword transfer instructions LDM  
,
LDRD  
,
STRD  
,
STM  
,
PUSH  
,
and POPthat can access Normal memory.  
To minimize the interrupt latency, ARM recommends that you do not perform:  
multiple accesses to areas of memory marked as Device or Strongly Ordered  
SWP operations to slow areas of memory.  
Exception processing  
The ARMv7-R architecture contains exception processing instructions to reduce interrupt  
handler entry and exit time:  
SRS  
Save return state to a specified stack frame.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
1-9  
   
Introduction  
RFE  
CPS  
Return from exception using data from the stack.  
Change processor state, such as interrupt mask setting and clearing, and mode  
changes.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
1-10  
Introduction  
1.4  
External interfaces of the processor  
The processor has the following interfaces for external access:  
For more information on these interfaces and how they are integrated into the system, see the  
AMBA 3 APB Protocol Specification and the CoreSight Architecture Specification.  
1.4.1  
APB Debug interface  
AMBA APBv3 is used for debugging purposes. CoreSight is the ARM architecture for  
multi-processor trace and debug. CoreSight defines what debug and trace components are  
required and how they are connected.  
Note  
The APB debug interface can also connect to a DAP-Lite. For more information on the  
DAP-Lite, see the CoreSight DAP-Lite Technical Reference Manual.  
1.4.2  
ETM interface  
You can connect an ETM-R4 to the processor through the ETM interface. The ETM-R4  
provides instruction and data trace for the processor. For more information on how the ETM-R4  
connects to the processor, see the CoreSight ETM-R4 Technical Reference Manual.  
All outputs are driven directly from a register unless specified otherwise. All signals are relative  
to CLKIN unless specified otherwise.  
The ETM interface includes these signals:  
an instruction interface  
a data interface  
an event interface  
other connections to the ETM.  
See ETM interface signals on page A-19 for information about the names of signals that form  
these interfaces. See Event bus interface on page 6-19 for more information about the event bus.  
1.4.3  
Test interface  
The test interface provides support for test during manufacture of the processor using Memory  
Built-In Self Test (MBIST). For more information on the test interface, see MBIST signals on  
page A-21. See the Cortex-R4 and Cortex-R4F Integration Manual for information about the  
timings of these signals.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
1-11  
           
Introduction  
1.5  
Power management  
The processor includes several microarchitectural features to reduce energy consumption:  
Accurate branch and return prediction, reducing the number of incorrect instruction fetch  
and decode operations.  
The caches use sequential access information to reduce the number of accesses to the tag  
RAMs and to unmatched data RAMs.  
Extensive use of gated clocks and gates to disable inputs to unused functional blocks.  
Because of this, only the logic actively in use to perform a calculation consumes any  
dynamic power.  
The processor uses four levels of power management:  
Run mode  
This mode is the normal mode of operation where all of the functionality  
of the processor is available.  
Standby mode  
This mode disables most of the clocks of the device, while keeping the  
device powered up. This reduces the power drawn to the static leakage  
current and the minimal clock power overhead required to enable the  
device to wake up from the Standby mode.  
Shutdown mode  
Dormant mode  
This mode has the entire device powered down. All state, including cache  
and TCM state, must be saved externally. The assertion of reset returns the  
processor to the run state.  
The processor can be implemented in such a way as to support Dormant  
mode. Dormant mode is a power saving mode in which the processor  
logic, but not the processor TCM and cache RAMs, is powered down. The  
processor state, apart from the cache and TCM state, is stored to memory  
before entry into Dormant mode, and restored after exit.  
For more information on preparing the Cortex-R4 to support Dormant  
mode, contact ARM.  
For more information on the power management features, see Chapter 10 Power Control.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
1-12  
   
Introduction  
1.6  
Configurable options  
Table 1-1 shows the features of the processor that can be configured using either  
build-configuration or pin-configuration. See Product documentation, design flow, and  
architecture on page 1-21 for information about configuration of the processor. Many of these  
features, if included, can also be enabled and disabled during software configuration.  
Table 1-1 Configurable options  
Build-configuration  
or pin-configuration  
Feature  
Options  
Sub-options  
Redundant core  
Single-core (no redundancy)  
Dual-core (redundant)  
-
Build  
Build  
In-phase clocks  
Out-of-phase clocks  
Instruction cache No i-cache  
i-cache included  
-
Build  
Build  
No error checking  
Parity error checking  
64-bit ECC error checking  
4KB (4x1KB ways)  
8KB (4x2KB ways)  
16KB (4x4KB ways)  
32KB (4x8KB ways)  
64KB (4x16KB ways)  
Build  
Data cache  
No d-cache  
-
Build  
Build  
d-cache included  
No error checking  
Parity error checking  
32-bit ECC error checking  
4KB (4x1KB ways)  
8KB (4x2KB ways)  
16KB (4x4KB ways)  
32KB (4x8KB ways)  
64KB (4x16KB ways)  
Build  
ATCM  
No ATCM ports  
One ATCM port  
-
Build and pin  
Build  
No error checking  
Parity error checking  
32-bit ECC error checking  
64-bit ECC error checking  
4KB, 8KB, 16KB, 32KB, 64KB,  
128KB, 256KB, 512KB, 1MB, 2MB,  
4MB, or 8MB  
Pin  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
1-13  
       
Introduction  
Table 1-1 Configurable options (continued)  
Build-configuration  
or pin-configuration  
Feature  
Options  
Sub-options  
BTCM  
No BTCM ports  
-
Build and pin  
Build  
One BTCM port (B0TCM)  
No error checking  
Parity error checking  
32-bit ECC error checking  
64-bit ECC error checking  
4KB, 8KB, 16KB, 32KB, 64KB,  
128KB, 256KB, 512KB, 1MB, 2MB,  
4MB, or 8MB  
Pin  
Two BTCM ports (B0TCM  
and B1TCM)  
No error checking  
Build  
Parity error checking  
32-bit ECC error checking  
64-bit ECC error checking  
2x2KB, 2x4KB, 2x8KB, 2x16KB,  
2x32KB, 2x64KB, 2x128KB,  
2x256KB, 2x512KB, 2x1MB, 2x2MB,  
or 2x4MB  
Pin  
Pin  
Interleaved on 64-bit granularity in  
memory  
Adjacent in memory  
Instruction  
endianness  
Little-endian  
-
Build  
Pin  
Pin-configured  
Little-endian  
Big-endian  
Floating point  
(VFP)  
No FPU  
-
-
-
Build  
FPU includeda  
No MPU  
MPU  
Build  
Build  
MPU included  
8 MPU regions  
12 MPU regions  
TCM bus parity  
No TCM address and control  
bus parity  
-
Build  
TCM address and control  
bus parity generated  
-
AXI bus parity  
No AXI bus parity  
-
-
Build  
AXI bus parity generated/  
checked  
Breakpoints  
Watchpoints  
ATCM at reset  
2-8 breakpoint register pairs  
1-8 watchpoint registers  
Disabled  
-
-
-
Build  
Build  
Pin  
Enabledb  
Base address 0x0  
Pin and build  
Base address configured  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
1-14  
 
Introduction  
Table 1-1 Configurable options (continued)  
Build-configuration  
or pin-configuration  
Feature  
Options  
Sub-options  
BTCM at reset  
Disabled  
Enabledb  
-
Pin  
Base address configured  
Pin and build  
Base address 0x0  
Peripheral ID  
RevAnd field  
Any 4-bit value  
-
Build  
Build  
AXI slave  
interface  
No AXI-slave  
-
-
-
-
AXI-slave included  
No TCM Hard Error Cache  
TCM Hard Error  
Cache  
Build  
Pin  
TCM Hard Error Cache  
included c  
Non-Maskable  
FIQ Interrupt  
Disabled (FIQ can be  
masked by software  
-
Enabled  
-
-
-
Parity typed  
Odd parity  
Even parity  
Pin  
a. Only available with the Cortex-R4F processor.  
b. Only if the relevant TCM port(s) are included.  
c. Only if at least one TCM port is included and uses ECC error checking.  
d. Only relevant if at least one TCM port is included and uses parity error checking, one of the caches includes parity checking,  
or AXI or TCM bus parity is included.  
Table 1-2 describes the various features that can be pin-configured to be either enabled or  
disabled at reset. It also shows which CP15 register field provides software configuration of the  
feature when the processor is out of reset. All of these fields exist in either the system control  
register, or one of the auxiliary control registers.  
Table 1-2 Configurable options at reset  
Feature  
Options  
Register  
Exception endianness  
Exception state  
Little-endian/big-endian data for exception handling  
ARM/Thumb state for exception handling  
EE  
TE  
Exception vector table  
TCM error checking  
Base address for exception vectors: 0x00000000  
/
0xFFFF0000  
V
ATCM parity check enablea  
ATCMPCEN  
BTCM parity check enable, for B0TCM and B1TCM independently a  
B0TCMPCEN/  
B1TCMPCEN  
ATCM ECC check enablea  
ATCMPCEN  
BTCM ECC check enabled, for B0TCM and B1TCM togethera  
B0TCMPCEN/  
B1TCMPCEN  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
1-15  
     
Introduction  
Table 1-2 Configurable options at reset (continued)  
Feature  
Options  
Register  
TCM external errors  
ATCM external error enable  
ATCMECEN  
BTCM external error enable, for B0TCM and B1TCM independently B0TCMECEN/  
B1TCMECEN  
ATCM load/store-64 enableb  
BTCM load/store-64 enableb  
TCM load/store-64  
(read-modify-write) behavior  
ATCMRMW  
BTCMRMW  
a. Can only be enabled if the appropriate TCM is configured with the appropriate error checking scheme, and the appropriate  
number of ports  
b. Can only be enabled if the appropriate TCM is not configured with 32-bit ECC.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
1-16  
 
Introduction  
1.7  
Execution pipeline stages  
The following stages make up the pipeline:  
the Fetch stages  
the Decode stages  
an Issue stage  
the three or four Execution stages.  
Figure 1-2 shows the Fetch and Decode pipeline stages of the processor and the pipeline  
operations that can take place at each stage.  
Fe1  
Fe2  
Pd  
De  
Instruction  
formatting  
branch  
1st fetch  
stage  
2nd fetch  
stage  
Instruction  
decode  
predicting  
Predicted branches and returns  
Figure 1-2 Processor Fetch and Decode pipeline stages  
The names of the pipeline stages and their functions are:  
Fe  
Pd  
De  
Instruction fetch where data is returned from instruction memory.  
Pre-decode where instructions are formatted and branch prediction occurs.  
Instruction decode.  
Figure 1-3 shows the Issue and Execution pipeline stages for the Cortex-R4 processor.  
Iss  
Ex1  
Ex2  
Wr  
Ret  
Register  
read,  
Load/store  
pipeline  
DC1  
DC2  
address  
generation,  
and  
Data  
processing  
pipeline  
instruction  
issue  
EX1  
EX1  
Wr  
Mispredicted direct branches  
Exception flush and mispredicted  
indirect branches  
Figure 1-3 Cortex-R4 Issue and Execution pipeline stages  
Figure 1-4 on page 1-18 shows the Issue and Execution pipeline stages for the Cortex-R4F  
processor.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
1-17  
           
Introduction  
Iss  
Ex1  
Ex2  
Wr  
Ret  
Load/store  
pipeline  
DC1  
DC2  
Register  
read,  
address  
generation,  
and  
instruction  
issue  
Data  
EX1  
F0  
EX1  
F1  
Wr  
processing  
pipeline  
Floating point  
pipeline  
F2  
Fwr  
Mispredicted direct branches  
Exception flush and mispredicted  
indirect branches  
Figure 1-4 Cortex-R4F Issue and Execution pipeline stages  
The names of the common pipeline stages and their functions are:  
Iss  
Register read and instruction issue to execute stages.  
Execute stages.  
Ex  
Wr  
Ret  
Write-back of data from the execution pipelines.  
Instruction retire.  
The names of the load/store pipeline stages and their functions are:  
DC1  
DC2  
First stage of data memory access.  
Second stage of data memory access.  
The names of the floating point pipeline stages and their functions are:  
F0  
Floating point register read.  
F1  
First stage of floating point execution.  
Second stage of floating point execution.  
Floating point writeback.  
F2  
Fwr  
The pipeline structure provides a pipelined 2-cycle memory access and single-cycle load-use  
penalty. This enables integration with slow RAM blocks and maintains good CPI at reasonable  
frequencies.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
1-18  
   
Introduction  
1.8  
Redundant core comparison  
The processor can be implemented with a second, redundant copy of most of the logic. This  
second core shares the input pins and the cache RAMs of the master core, so only one set of  
cache RAMs is required. The master core drives the output pins and the cache RAMs.  
Comparison logic can be included during implementation which compares the outputs of the  
redundant core with those of the master core. If a fault occurs in the logic of either core, because  
of radiation or circuit failure, this is detected by the comparison logic. Used in conjunction with  
the RAM error detection schemes, this can help protect the system from faults. The inputs  
DCCMINP[7:0] and DCCMINP2[7:0] and the outputs DCCMOUT[7:0] and  
DCCMOUT2[7:0] enable the comparison logic inside the processor to communicate with the  
rest of the system.  
ARM provides example comparison logic, but you can change this during implementation. If  
you are implementing a processor with dual-redundant cores, contact ARM for more  
information. If you are integrating a Cortex-R4 macrocell with dual-redundant cores, contact the  
implementer for more details.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
1-19  
   
Introduction  
1.9  
Test features  
The processor is delivered as fully-synthesizable RTL and is a fully-static design. Scan-chains  
and test wrappers for production test can be inserted into the design by the synthesis tools during  
implementation. See the relevant reference methodology documentation for more information.  
Production test of the processor cache and TCM RAMs can be done through the dedicated,  
pipelined MBIST interface. This interface shares some of the multiplexing present in the  
processor design, which improves the potential frequency compared to adding multiplexors to  
the RAM modules. See the Cortex-R4 and Cortex-R4F Integration Manual for more  
information about this interface, and how to control it.  
In addition, you can use the AXI slave interface to read and write the cache and TCM RAMs.  
You can use this feature to test the cache RAMs in a running system. This might be required in  
a safety-critical system. The TCM RAMs can be read and written directly by the program  
running on the processor. You can also use the AXI slave interface for swapping a test program  
in to the TCMs for the processor to execute. See Accessing RAMs using the AXI slave interface  
on page 9-24 for more information about how to access the RAMs using the AXI slave interface.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
1-20  
   
Introduction  
1.10 Product documentation, design flow, and architecture  
This section describes the content of the product documents, how they relate to the design flow,  
and the relevant architectural standards and protocols.  
Note  
See Further reading on page xx for more information about the documentation described in this  
section.  
1.10.1 Documentation  
The following books describe the processor:  
Technical Reference Manual  
The Technical Reference Manual (TRM) describes the processor functionality  
and the effects of functional options on the behavior of the processor. It is required  
at all stages of the design flow. Some behavior described in the TRM might not  
be relevant, because of the way the processor has been implemented and  
integrated. If you are programming the processor, contact the implementer to  
determine the build configuration of the implementation, and the integrator to  
determine the pin configuration of the SoC that you are using.  
Configuration and Sign-Off Guide  
The Configuration and Sign-Off Guide (CSG) describes:  
the available build configuration options and related issues in selecting  
them  
how to configure the Register Transfer Level (RTL) with the build  
configuration options  
the processes to sign off the configured RTL and final macrocell.  
The ARM product deliverables include reference scripts and information about  
using them to implement your design. Reference methodology documentation  
from your EDA tools vendor complements the CSG. The CSG is a confidential  
book that is only available to licensees.  
Integration Manual  
The Integration Manual (IM) describes how to integrate the processor into a SoC  
including describing the pins that the integrator must tie off to configure the  
macrocell for the required integration. Some of the integration is affected by the  
configuration options that were used to implement the processor. Contact the  
implementer of the macrocell that you are using to determine the implemented  
build configuration options. The IM is a confidential book that is only available  
to licensees.  
1.10.2 Design flow  
The processor is delivered as synthesizable RTL. Before it can be used in a product, it must go  
through the following process:  
1.  
Implementation. The implementer configures and synthesizes the RTL to produce a hard  
macrocell. This includes integrating the cache RAMs into the design.  
2.  
Integration. The integrator integrates the hard macrocell into a SoC, connecting it to a  
memory system and to appropriate peripherals for the intended function. This memory  
system includes the Tightly Coupled Memories (TCMs).  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
1-21  
   
Introduction  
3.  
Programming. The system programmer develops the software required to configure and  
initialize the processor, and possibly tests the required application software on the  
processor.  
Each of these stages can be performed by a different company. Configuration options are  
available at each stage. These options affect the behavior and available features at the next stage:  
Build configuration  
The implementer chooses the options that affect how the RTL source files are  
pre-processed. They usually include or exclude logic that can affect the area or  
maximum frequency of the resulting macrocell.  
For example, the BTCM interface can be configured to have zero, one (B0TCM)  
or two (B0TCM and B1TCM) ports. If one port is chosen, the logic for the second  
port is excluded from the macrocell, although the pins remain, and the second port  
(B1TCM) cannot be used on that macrocell.  
Configuration inputs  
The integrator configures some features of the processor by tying inputs to  
specific values. These configurations affect the start-up behavior before any  
software configuration is made. They can also limit the options available to the  
software.  
For example, if the build configuration for the macrocell includes both BTCM  
ports, the integrator can choose how many ports to actually use, and therefore  
how many RAMs must be integrated with the macrocell. If the integrator only  
wishes to use one BTCM port, they can connect RAM to the B0TCM port only,  
and tie the ENTCM1IF input to zero to indicate that the B1TCM is not available.  
Software configuration  
The programmer configures the processor by programming particular values into  
software-visible registers. This affects the behavior of the processor.  
For example, the enable bit in the BTCM Region Register controls whether or not  
memory accesses are performed to the BTCM interface. However, the BTCM  
cannot, and must not, be enabled if the build configuration does not include any  
BTCM ports, or if the pin configuration indicates that no RAMs have been  
integrated onto the BTCM ports.  
Note  
This manual refers to implementation-defined features that are applicable to build configuration  
options. References to a feature which is included mean that the appropriate build and pin  
configuration options have been selected, while references to an enabled feature mean one that  
has also been configured by software.  
1.10.3 Architectural information  
The Cortex-R4 processor conforms to, or implements, the following specifications:  
ARM Architecture  
This describes:  
The behavior and encoding of the instructions that the processor can  
execute.  
The modes and states that the processor can be in.  
The various data and control registers that the processor must contain.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
1-22  
Introduction  
The properties of memory accesses.  
The debug architecture you can use to debug the processor. The TRM gives  
more information about the implemented debug features.  
The Cortex-R4 processor implements the ARMv7-R architecture profile.  
Advanced Microcontroller Bus Architecture protocol  
Advanced Microcontroller Bus Architecture (AMBA) is an open standard,  
on-chip bus specification that defines the interconnection and management of  
functional blocks that make up a System-on-Chip (SoC). It facilitates  
development of embedded processors with multiple peripherals.  
IEEE 754  
This is the IEEE Standard for Binary Floating Point Arithmetic.  
An architecture specification typically defines a number of versions, and includes features that  
are either optional or partially specified. The TRM describes which architectures are used,  
including which version is implemented, and the architectural choices made for the  
implementation. The TRM does not provide detailed information about the architecture, but  
some architectural information is included to give an overview of the implementation or, in the  
case of control registers, to make the manual easier to use. See the appropriate specification for  
more information about the implemented architectural features.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
1-23  
Introduction  
1.11 Product revision information  
This manual is for major revision 1 of the processor. At the time of release, this includes the  
r1p0, r1p1, r1p2, and r1p3 releases, although the vast majority of the information in this  
document will also be applicable to any future r1px releases. The following broadly describes  
the changes made in each subsequent revision of the processor:  
Revision 1 Introduction of the ECC functional options and addition of the FPU options, to  
implement the Cortex-R4F processor.  
Note  
The r1p0 release was not generally available.  
1.11.1 Processor identification  
The Cortex-R4 processor contains a number of IDentification (ID) registers that enable software  
or a debugger to identify the processor as Cortex-R4, and the variant (major revision) and  
revision (minor revision) of the design. These registers are:  
Main ID Register (MIDR)  
This register is accessible by software and identifies the part, the variant, and the  
revision. See c0, Main ID Register on page 4-14. A copy of this register can also  
be read by a debugger through the debug APB interface. See Processor ID  
Debug ID Register (DIDR)  
This register can be read by a debugger through the debug APB interface, and by  
software. It identifies the variant and revision. See CP14 c0, Debug ID Register  
Peripheral ID Registers  
These registers can be accessed through the debug APB interface only, and  
identify the revision number of the processor. See Debug Identification Registers  
Floating Point System ID Register (FPSID)  
When the build-configuration includes the floating point unit, this register  
identifies the revision number of the floating-point unit. See Floating-Point  
Note  
Floating point functionality is provided only with the Cortex-R4F processor.  
The revision number of the processor, in the Peripheral ID and FPSID registers, is a single field  
that incorporates information about both major and minor revisions.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
1-24  
   
Introduction  
Table 1-3 shows the mappings between these various numbers, for all releases.  
Table 1-3 ID values for different product versions  
ID value  
r0p0 r0p1 r0p2 r0p3 r1p0 r1p1 r1p2 r1p3  
0x1  
0x3  
0x1  
0x3  
0x7  
0x7  
Variant field, Main ID Register  
0x0  
0x0  
0x0  
0x0  
0x0  
-
0x0  
0x1  
0x0  
0x1  
0x1  
-
0x0  
0x2  
0x0  
0x2  
0x2  
-
0x0  
0x3  
0x0  
0x3  
0x5  
-
0x1  
0x0  
0x1  
0x0  
0x3  
0x3  
0x1  
0x1  
0x1  
0x1  
0x4  
0x4  
0x1  
0x2  
0x1  
0x2  
0x6  
0x6  
Revision field, Main ID Register  
Variant field, Debug ID Register  
Revision field, Debug ID Register  
Revision number, Peripheral ID Registers  
Revision number, FPSID Register  
1.11.2 Architectural information  
The ARM Architecture includes a number of registers that identify the version of the  
architecture and some of the architectural features that a processor implements. Chapter 4  
System Control Coprocessor describes the values that the processor implements for the fields in  
these registers. For details of the possible values and their meanings for these fields, see the  
ARM Architecture Reference Manual.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
1-25  
   
Chapter 2  
Programmer’s Model  
This chapter describes the processor registers and provides an overview for programming the  
microprocessor. It contains the following sections:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-1  
   
Programmer’sModel  
2.1  
About the programmer’s model  
The processor implements the ARMv7-R architecture that provides:  
the 32-bit ARM instruction set  
the extended Thumb instruction set introduced in ARMv6T2, that uses Thumb-2  
technology to provide a wide range of 32-bit instructions.  
For more information on the ARM and Thumb instruction sets, see the ARM Architecture  
Reference Manual. This chapter describes some of the main features of the architecture but, for  
a complete description, see the ARM Architecture Reference Manual.  
This chapter also makes reference to older versions of the ARM architecture that the processor  
does not implement. These references are included to contrast the behavior of the Cortex-R4  
processor with other processors you might have used that implement an older version of the  
architecture.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-2  
   
Programmer’sModel  
2.2  
Instruction set states  
The processor has two instruction set states:  
ARM state  
The processor executes 32-bit, word-aligned ARM instructions in this  
state.  
Thumb state  
The processor executes 32-bit and 16-bit halfword-aligned Thumb  
instructions in this state.  
Note  
Transition between ARM state and Thumb state does not affect the processor mode or the  
register contents.  
2.2.1  
Switching state  
The instruction set state of the processor can be switched between ARM state and Thumb state:  
Using the BXand BLXinstructions, by a load to the PC, or with a data-processing instruction  
that does not set flags, with the PC as the destination register. Switching state is described  
in the ARM Architecture Reference Manual.  
Note  
When the BXJinstruction is used the processor invokes the BXinstruction.  
Automatically on an exception. You can write an exception handler routine in ARM or  
Thumb code. For more information, see Exceptions on page 2-16.  
2.2.2  
Interworking ARM and Thumb state  
The processor enables you to mix ARM and Thumb code. For more information about  
interworking ARM and Thumb, see the RealView Compilation Tools Developer Guide.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-3  
   
Programmer’sModel  
2.3  
Operating modes  
In each state there are seven modes of operation:  
User (USR) mode is the usual mode for the execution of ARM or Thumb programs. It is  
used for executing most application programs.  
Fast interrupt (FIQ) mode is entered on taking a fast interrupt.  
Interrupt (IRQ) mode is entered on taking a normal interrupt.  
Supervisor (SVC) mode is a protected mode for the operating system and is entered on  
taking a Supervisor Call (SVC), formerly SWI.  
Abort (ABT) mode is entered after a data or instruction abort.  
System (SYS) mode is a privileged user mode for the operating system.  
Undefined (UND) mode is entered when an Undefined instruction exception occurs.  
Modes other than User mode are collectively known as Privileged modes. Privileged modes are  
used to service interrupts or exceptions, or access protected resources.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-4  
   
Programmer’sModel  
2.4  
Data types  
The processor supports these data types:  
doubleword, 64-bit  
word, 32-bit  
halfword, 16-bit  
byte, 8-bit.  
Note  
When any of these types are described as unsigned, the N-bit data value represents a  
non-negative integer in the range 0 to +2N-1, using normal binary format.  
When any of these types are described as signed, the N-bit data value represents an integer  
in the range -2N-1 to +2N-1-1, using two’s complement format.  
For best performance you must align these data types in memory as follows:  
doubleword quantities aligned to 8-byte boundaries, doubleword aligned  
word quantities aligned to 4-byte boundaries, word aligned  
halfword quantities aligned to 2-byte boundaries halfword aligned  
byte quantities can be placed on any byte boundary.  
The processor supports mixed-endian and unaligned access. For more information, see  
Note  
You cannot use LDRD LDM, STRD, or STMinstructions to access 32-bit quantities if they are not  
,
32-bit aligned.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-5  
   
Programmer’sModel  
2.5  
Memory formats  
The processor views memory as a linear collection of bytes numbered in ascending order from  
zero. For example, bytes 0-3 hold the first stored word, and bytes 4-7 hold the second stored  
word.  
The processor can treat words of data in memory as being stored in either:  
Additionally, the processor supports mixed-endian and unaligned data accesses. For more  
information, see the ARM Architecture Reference Manual.  
2.5.1  
Byte-invariant big-endian format  
In byte-invariant big-endian (BE-8) format, the processor stores the most significant byte of a  
word at the lowest-numbered byte, and the least significant byte at the highest-numbered byte.  
Figure 2-1 shows byte-invariant big-endian (BE-8) format.  
Memory  
Register  
Address  
A[31:0]  
7
0
31  
24 23  
16 15  
8
7
0
B0  
B1  
B2  
B3  
msbyte  
lsbyte  
B0  
B1  
B2  
B3  
+1  
+2  
+3  
Figure 2-1 Byte-invariant big-endian (BE-8) format  
2.5.2  
Little-endian format  
In little-endian format, the lowest-numbered byte in a word is the least significant byte of the  
word and the highest-numbered byte is the most significant. Figure 2-2 shows little-endian  
format.  
Memory  
Register  
Address  
A[31:0]  
7
0
31  
24 23  
16 15  
8
7
0
b0  
b1  
b2  
b3  
lsbyte  
b3  
b2  
b1  
b0  
+1  
+2  
+3  
msbyte  
Figure 2-2 Little-endian format  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-6  
                   
Programmer’sModel  
2.6  
Registers  
The processor has a total of 37 program registers:  
31 general-purpose 32-bit registers  
six 32-bit status registers.  
These registers are not all accessible at the same time. The processor state and operating mode  
determine the registers that are available to the programmer.  
2.6.1  
The register set  
In the processor the same register set is used in both the ARM and Thumb states. Sixteen general  
registers and one or two status registers are accessible at any time. In Privileged modes,  
alternative mode-specific banked registers become available. Figure 2-3 on page 2-9 shows the  
registers that are available in each mode.  
The register set contains 16 directly-accessible registers, R0-R15. Another register, the Current  
Program Status Register (CPSR), contains condition code flags, status bits, and current mode  
bits. Registers R0-R12 are general-purpose registers that hold either data or address values.  
Registers R13, R14, R15, and the CPSR have these special functions:  
Stack pointer  
Software normally uses register R13 as a Stack Pointer (SP). The SRSand  
RFEinstructions use Register R13.  
Link Register  
Register R14 is used as the subroutine Link Register (LR).  
Register R14 receives the return address when a Branch with Link (BLor  
BLX) instruction is executed.  
You can use R14 as a general-purpose register at all other times. The  
corresponding banked registers R14_svc, R14_irq, R14_fiq, R14_abt, and  
R14_und similarly hold the return values when interrupts and exceptions  
are taken, or when BLor BLXinstructions are executed within interrupt or  
exception routines.  
Program Counter Register R15 holds the PC:  
in ARM state this is word-aligned  
in Thumb state this is either word or halfword-aligned.  
Note  
There are special cases for reading R15:  
reading the address of the current instruction plus, either:  
4 in Thumb state  
8 in ARM state.  
reading 0x00000000(zero).  
There are special cases for writing R15:  
causing a branch to the address that was written to R15  
ignoring the value that was written to R15  
writing bits [31:28] of the value that was written to R15 to the  
condition flags in the CPSR, and ignoring bits [27:20] (used for the  
MRCinstruction only).  
You must not assume any of these special cases unless it is explicitly stated  
in the instruction description. Instead, you must treat instructions with  
register fields equal to R15 as Unpredictable.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-7  
   
Programmer’sModel  
For more information, see the ARM Architecture Reference Manual.  
In Privileged modes, another register, the Saved Program Status Register (SPSR), is accessible.  
This contains the condition code flags, status bits, and current mode bits saved as a result of the  
exception that caused entry to the current mode.  
Banked registers have a mode identifier that indicates which mode they relate to. Table 2-1lists  
these identifiers.  
Table 2-1 Register mode identifiers  
Mode  
Mode identifier  
usra  
User  
Fast interrupt fiq  
Interrupt  
Supervisor  
Abort  
irq  
svc  
abt  
usra  
und  
System  
Undefined  
a. The usridentifier is usually  
omitted from register  
names. It is only used in  
descriptions where the User  
or System mode register is  
specifically accessed from  
another operating mode.  
FIQ mode has seven banked registers mapped to R8–R14 (R8_fiq–R14_fiq). As a result many  
FIQ handlers do not have to save any registers.  
The Supervisor, Abort, IRQ, and Undefined modes each have alternative mode-specific  
registers mapped to R13 and R14, permitting a private stack pointer and link register for each  
mode.  
Figure 2-3 on page 2-9 shows the register set, and those registers that are banked.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-8  
   
Programmer’sModel  
General registers and program counter  
System and User  
FIQ  
Supervisor  
Abort  
R0  
IRQ  
Undefined  
R0  
R0  
R1  
R2  
R3  
R4  
R5  
R6  
R7  
R0  
R0  
R1  
R2  
R3  
R4  
R5  
R6  
R7  
R8  
R9  
R0  
R1  
R1  
R1  
R1  
R2  
R2  
R2  
R2  
R3  
R3  
R3  
R3  
R4  
R4  
R4  
R4  
R5  
R5  
R5  
R5  
R6  
R6  
R6  
R6  
R7  
R7  
R7  
R7  
R8  
R8_fiq  
R8  
R8  
R8  
R9  
R9_fiq  
R9  
R9  
R9  
R10  
R11  
R12  
R13  
R14  
R15  
R10_fiq  
R11_fiq  
R12_fiq  
R13_fiq  
R14_fiq  
R15 (PC)  
R10  
R11  
R12  
R13_svc  
R14_svc  
R15 (PC)  
R10  
R11  
R12  
R13_abt  
R14_abt  
R15 (PC)  
R10  
R10  
R11  
R12  
R13_und  
R14_und  
R15 (PC)  
R11  
R12  
R13_irq  
R14_irq  
R15 (PC)  
Program status registers  
CPSR  
CPSR  
CPSR  
CPSR  
CPSR  
CPSR  
SPSR_fiq  
SPSR_svc  
SPSR_abt  
SPSR_irq  
SPSR_und  
= banked register  
Figure 2-3 Register organization  
Note  
For 16-bit Thumb instructions, the high registers, R8–R15, are not part of the standard register  
set. You can use special variants of the MOVinstruction to transfer a value from a low register, in  
the range R0–R7, to a high register, and from a high register to a low register. The CMPinstruction  
enables you to compare high register values with low register values. The ADDinstruction  
enables you to add high register values to low register values. For more information, see the  
ARM Architecture Reference Manual.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-9  
   
Programmer’sModel  
2.7  
Program status registers  
The processor contains one CPSR and five SPSRs for exception handlers to use. The program  
status registers:  
hold information about the most recently performed ALU operation  
control the enabling and disabling of interrupts  
set the processor operating mode.  
Figure 2-4 shows the bit arrangement in the status registers.  
31 30 29 28 27 26 25 24 23  
N Z C V Q  
20 19  
16 15  
10 9  
8
7
I
6
F
5
T
4
0
J
DNM  
GE[3:0]  
IT[7:2]  
E A  
M[4:0]  
Mode bits  
Greater than  
or equal to  
Java state bit  
IT[1:0]  
Thumb state bit  
FIQ disable  
IRQ disable  
Sticky overflow  
Overflow  
Imprecise abort  
disable bit  
Carry/Borrow/Extend  
Zero  
Data endianness bit  
Negative/Less than  
Figure 2-4 Program status register  
The following sections explain the meanings of these bits:  
2.7.1  
The N, Z, C, and V bits  
The N, Z, C, and V bits are the condition code flags. You can optionally set them with arithmetic  
and logical operations, and also with MSRinstructions and MRCinstructions to R15. The processor  
tests these flags in accordance with an instruction's condition code to determine whether to  
execute that instruction.  
In ARM state, most instructions can execute conditionally on the state of the N, Z, C, and V bits.  
The exceptions are:  
BKPT  
CPS  
LDC2  
MCR2  
MCRR2  
MRC2  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-10  
         
Programmer’sModel  
MRRC2  
PLD  
RFE  
SETEND  
SRS  
STC2  
.
In Thumb state, the processor can only execute the Branch instruction conditionally. Other  
instructions can be made conditional by placing them in the If-Then (IT) block. For more  
information about conditional execution in Thumb state, see the ARM Architecture Reference  
Manual.  
2.7.2  
The Q bit  
Certain multiply and fractional arithmetic instructions can set the Sticky Overflow, Q, flag:  
QADD  
QDADD  
QSUB  
QDSUB  
SMLAD  
SMLAxy  
SMLAWy  
SMLSD  
SMUAD  
SSAT  
SSAT16  
USAT  
USAT16  
.
The Q flag is sticky in that, when an instruction sets it, this bit remains set until an MSRinstruction  
writing to the CPSR explicitly clears it. Instructions cannot execute conditionally on the status  
of the Q flag.  
To determine the status of the Q flag you must read the PSR into a register and extract the Q flag  
from this. For information of how the Q flag is set and cleared, see individual instruction  
definitions in the ARM Architecture Reference Manual.  
2.7.3  
The IT bits  
IT[7:5] encodes the base condition code for the current IT block, if any. It contains b000 when  
no IT block is active.  
IT[4:0] encodes the number of instructions that are to be conditionally executed, and whether  
the condition for each is the base condition code or the inverse of the base condition code. It  
contains b00000 when no IT block is active.  
When an IT instruction is executed, these bits are set according to the condition in the  
instruction, and the Then and Else (T and E) parameters in the instruction. During execution of  
an IT block, IT[4:0] is shifted to:  
reduce the number of instructions to be conditionally executed by one  
move the next bit into position to form the least significant bit of the condition code.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-11  
   
Programmer’sModel  
For more information on the operation of the IT execution state bits, see the ARM Architecture  
Reference Manual.  
2.7.4  
2.7.5  
The J bit  
The J bit in the CPSR returns 0 when read.  
Note  
You cannot use an MSRto change the J bit in the CPSR.  
The DNM bits  
Software must not modify the Do Not Modify (DNM) bits. These bits are:  
Readable, to preserve the state of the processor, for example, during process context  
switches.  
Writable, to enable the processor to restore its state. To maintain compatibility with future  
ARM processors, and as good practice, use a read-modify-write strategy when you  
change the CPSR.  
2.7.6  
The GE bits  
Some of the SIMD instructions set GE[3:0] as greater-than-or-equal bits for individual  
halfwords or bytes of the result, as Table 2-2 shows.  
Table 2-2 GE[3:0] settings  
GE[0]  
GE[3]  
GE[2]  
GE[1]  
A op B greater than  
or equal to C  
A op B greater than  
or equal to C  
A op B greater  
than or equal to C  
A op B greater  
than or equal to C  
Instruction  
Signed  
SADD16  
SSUB16  
SADDSUBX  
SSUBADDX  
SADD8  
[31:16] + [31:16] 0  
[31:16] - [31:16] 0  
[31:16] + [15:0] 0  
[31:16] - [15:0] 0  
[31:24] + [31:24] 0  
[31:24] - [31:24] 0  
[31:16] + [31:16] 0  
[31:16] - [31:16] 0  
[31:16] + [15:0] 0  
[31:16] - [15:0] 0  
[23:16] + [23:16] 0  
[23:16] - [23:16] 0  
[15:0] + [15:0] 0  
[15:0] - [15:0] 0  
[15:0] - [31:16] 0  
[15:0] + [31:16] 0  
[15:8] + [15:8] 0  
[15:8] - [15:8] 0  
[15:0] + [15:0] 0  
[15:0] - [15:0] 0  
[15:0] - [31:16] 0  
[15:0] + [31:16] 0  
[7:0] + [7:0] 0  
SSUB8  
[7:0] - [7:0] 0  
Unsigned  
UADD16  
USUB16  
UADDSUBX  
USUBADDX  
UADD8  
[31:16] + [31:16] 216 [31:16] + [31:16] 216  
[15:0] + [15:0] 216  
[15:0] - [15:0] 0  
[15:0] - [31:16] 0  
[15:0] + [15:0] 216  
[15:0] - [15:0] 0  
[15:0] - [31:16] 0  
[31:16] - [31:16] 0  
[31:16] + [15:0] 216  
[31:16] - [15:0] 0  
[31:16] - [31:16] 0  
[31:16] + [15:0] 216  
[31:16] - [15:0] 0  
[15:0] + [31:16] 216 [15:0] + [31:16] 216  
[31:24] + [31:24] 28  
[23:16] + [23:16] 28  
[15:8] + [15:8] 28  
[7:0] + [7:0] 28  
USUB8  
[31:24] - [31:24] 0  
[23:16] - [23:16] 0  
[15:8] - [15:8] 0  
[7:0] - [7:0] 0  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-12  
         
Programmer’sModel  
Note  
GE bit is 1 if A op B C, otherwise 0.  
The SELinstruction uses GE[3:0] to select which source register supplies each byte of its result.  
Note  
For unsigned operations, the usual ARM rules determine the GE bits for carries out of  
unsigned additions and subtractions, and so are carry-out bits.  
For signed operations, the rules for setting the GE bits are chosen so that they have the  
same sort of greater than or equal functionality as for unsigned operations.  
2.7.7  
The E bit  
ARM and Thumb instructions are provided to set and clear the E bit. The E bit controls  
load/store endianness. See the ARM Architecture Reference Manual for information on where  
the E bit is used.  
Architecture versions prior to ARMv6 specify this bit as SBZ. This ensures no endianness  
reversal on loads or stores.  
2.7.8  
2.7.9  
The A bit  
The A bit is set automatically. It disables imprecise Data Aborts. For more information on how  
The I and F bits  
The I and F bits are the interrupt disable bits:  
when the I bit is set, IRQ interrupts are disabled  
when the F bit is set, FIQ interrupts are disabled.  
Software can use MSR  
,
CPS, MOVS pc, SUBS pc, LDM ..,{..pc}^, or RFE instructions to change the  
values of the I and F bits.  
When NMFIs are enabled, updates to the F bit are restricted. For more information see  
2.7.10 The T bit  
The T bit reflects the instruction set state:  
when the T bit is set, the processor executes in Thumb state  
when the T bit is clear, the processor executes in ARM state.  
Note  
Never use an MSRinstruction to force a change to the state of the T bit in the CPSR. The processor  
ignores any attempt to modify the T bit using an MSRinstruction.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-13  
       
Programmer’sModel  
2.7.11 The M bits  
M[4:0] are the mode bits. These bits determine the processor operating mode as Table 2-3  
shows.  
Table 2-3 PSR mode bit values  
Visible state registers  
M[4:0] Mode  
Thumb  
ARM  
b10000 User  
b10001 FIQ  
R0–R7, R8-R12, SP, LR, PC, CPSR  
R0–R14, PC, CPSR  
R0–R7, R8_fiq-R12_fiq, SP_fiq, LR_fiq PC,  
CPSR, SPSR_fiq  
R0–R7, R8_fiq–R14_fiq, PC, CPSR,  
SPSR_fiq  
b10010 IRQ  
R0–R7, R8-R12, SP_irq, LR_irq, PC, CPSR,  
SPSR_irq  
R0–R12, R13_irq, R14_irq, PC, CPSR,  
SPSR_irq  
b10011 Supervisor R0–R7, R8-R12, SP_svc, LR_svc, PC, CPSR,  
SPSR_svc  
R0–R12, R13_svc, R14_svc, PC, CPSR,  
SPSR_svc  
b10111 Abort  
R0–R7, R8-R12, SP_abt, LR_abt, PC, CPSR,  
SPSR_abt  
R0–R12, R13_abt, R14_abt, PC, CPSR,  
SPSR_abt  
b11011 Undefined R0–R7, R8-R12, SP_und, LR_und, PC, CPSR,  
SPSR_und  
R0–R12, R13_und, R14_und, PC, CPSR,  
SPSR_und  
b11111 System  
R0–R7, R8-R12, SP, LR, PC, CPSR  
R0–R14, PC, CPSR  
Note  
In Privileged mode an illegal value programmed into M[4:0] causes the processor to enter  
System mode.  
In User mode M[4:0] can be read. Writes to M[4:0] are ignored.  
2.7.12 Modification of PSR bits by MSR instructions  
In architecture versions earlier than ARMv6, MSRinstructions can modify the flags byte, bits  
[31:24], of the CPSR in any mode, but the other three bytes are only modifiable in Privileged  
modes.  
In the ARMv7-R architecture each CPSR bit falls into one of these categories:  
Bits that are freely modifiable from any mode, either directly by MSRinstructions or by  
other instructions whose side-effects include writing the specific bit or writing the entire  
CPSR.  
Bits in Figure 2-4 on page 2-10 that are in this category are N, Z, C, V, Q, GE[3:0], and E.  
Bits that an MSRinstruction must never modify, and so must only be written as a side-effect  
of another instruction. If an MSRinstruction tries to modify these bits, the results are  
architecturally Unpredictable. In the processor these bits are not affected.  
The bits in Figure 2-4 on page 2-10 that are in this category are the execution state bits  
[26:24], [15:10], and [5].  
Bits that can only be modified from Privileged modes, and that instructions completely  
protect from modification while the processor is in User mode. Entering a processor  
exception is the only way to modify these bits while the processor is in User mode, as  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-14  
     
Programmer’sModel  
Bits in Figure 2-4 on page 2-10 that are in this category are A, I, F, and M[4:0].  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-15  
Programmer’sModel  
2.8  
Exceptions  
Exceptions are taken whenever the normal flow of a program must temporarily halt, for  
example, to service an interrupt from a peripheral. Before attempting to handle an exception, the  
processor preserves the critical parts of the current processor state so that the original program  
can resume when the handler routine has finished.  
This section provides information of the processor exception handling:  
Note  
When the processor is in debug halt state, and an exception occurs, it is handled differently to  
2.8.1  
Exception entry and exit summary  
Table 2-4 summarizes the PC value preserved in the relevant R14 on exception entry, and the  
recommended instruction for exiting the exception handler.  
Table 2-4 Exception entry and exit  
Previous state  
Exception  
or entry  
Recommended return instruction  
Notes  
ARMR14_x Thumb R14_x  
SVCa  
MOVS PC, R14_svc  
IA + 4  
IA + 4  
IA + 2  
IA + 2  
Where the IA is the  
address of the SVC or  
Undefined instruction.  
Variesb  
UNDEF  
SUBS PC, R14_abt, #4  
PABT  
IA + 4  
IA + 4  
Where the IA is the  
address of instruction that  
had the Prefetch Abort.  
SUBS PC, R14_fiq, #4  
SUBS PC, R14_irq, #4  
FIQ  
IRQ  
IA + 4  
IA + 4  
IA + 4  
IA + 4  
Where the IA is the  
address of the instruction  
that was not executed  
because the FIQ or IRQ  
took priority.  
SUBS PC, R14_abt, #8  
DABT  
IA + 8  
IA + 8  
Where the IA is the  
address of the Load or  
Store instruction that  
generated the Data Abort.  
NA  
RESET  
BKPT  
-
-
The value saved in  
R14_svc on reset is  
Unpredictable.  
SUBS PC, R14_abt, #4  
IA + 4  
IA + 4  
Software breakpoint.  
a. Formerly SWI.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-16  
         
Programmer’sModel  
b. The return instruction you must use after an UNDEF exception has been handled depends on whether you want to retry the  
undefined instruction or not and, if so, on the size of the undefined instruction.  
Taking an exception  
When taking an exception the processor:  
1.  
Preserves the address of the next instruction in the appropriate LR. When the exception is  
taken from:  
ARM state  
The processor writes the address of the instruction into the LR, offset by a value  
(current IA + 4 or IA + 8 depending on the exception) that causes the program  
to resume from the correct place on return.  
Thumb state  
The processor writes the address of the instruction into the LR, offset by a value  
(current IA + 2, IA + 4 or IA + 8 depending on the exception) that causes the  
program to resume from the correct place on return.  
2.  
Copies the CPSR into the appropriate SPSR. Depending on the exception type, the  
processor might modify the IT execution state bits of the CPSR prior to this operation to  
facilitate a return from the exception.  
3.  
4.  
Forces the CPSR mode bits to a value that depends on the exception and clears the IT  
execution state bits in the CPSR.  
Sets the E bit based on the state of the EE bit. Both these bits are contained in the System  
5.  
6.  
The T bit is set based on the state of the TE bit.  
Forces the PC to fetch the next instruction from the relevant exception vector.  
The processor can also set the interrupt disable flags to prevent otherwise unmanageable nesting  
of exceptions.  
Leaving an exception  
When an exception has completed, the exception handler must move the LR, minus an offset,  
to the PC. The offset varies according to the type of exception, as Table 2-4 on page 2-16 shows.  
Typically the return instruction is an arithmetic or logical operation with the S bit set and Rd =  
R15, so the processor copies the SPSR back to the CPSR. Alternatively, an LDM ..,{..pc}^or  
RFEinstruction can perform a similar operation if the return state has been pushed onto a stack.  
Note  
The action of restoring the CPSR from the SPSR:  
Automatically restores the T, E, A, I, and F bits to the value they held immediately prior  
to the exception.  
Normally resets the IT execution state bits to the values held immediately prior to the  
exception. If the exception handler wants to return to the following instruction, these bits  
might require to be manually advanced to avoid applying the incorrect condition codes to  
that instruction. For more information about the IT instruction and Undefined instruction,  
and an example of the exception handler code, see the ARM Architecture Reference  
Manual.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-17  
Programmer’sModel  
Because SVC handlers are always expected to return after the SVCinstruction, the IT  
execution state bits are automatically advanced when an exception is taken prior to  
copying the CPSR into the SPSR.  
2.8.2  
Reset  
When the nRESET signal is driven LOW a reset occurs, and the processor abandons the  
executing instruction.  
When nRESET is driven HIGH again the processor:  
1.  
Forces CPSR M[4:0] to b10011 (Supervisor mode) and sets the A, I, and F bits in the  
CPSR. The E bit is set based on the state of the CFGEE pin. Other bits in the CPSR are  
indeterminate.  
2.  
3.  
Forces the PC to fetch the next instruction from the reset vector address.  
Reverts to ARM state or Thumb state depending on the state of the TEINIT pin, and  
resumes execution.  
After reset, all register values except the PC and CPSR are indeterminate.  
behavior for the processor.  
2.8.3  
Interrupts  
The processor has two interrupt inputs, for normal interrupts (nIRQ) and fast interrupts (nFIQ).  
Each interrupt pin, when asserted and not masked, causes the processor to take the appropriate  
type of interrupt exception. See Exceptions on page 2-16 for more information. The CPSR.F and  
CPSR.I bits control masking of fast and normal interrupts respectively.  
A number of features exist to improve the interrupt latency, that is, the time taken between the  
assertion of the interrupt input and the execution of the interrupt handler. By default, the  
processor uses the Low Interrupt Latency (LIL) behaviors introduced in version 6 and later of  
the ARM Architecture. The processor also has a port for connection of a Vectored Interrupt  
Controller (VIC), and supports Non-Maskable Fast Interrupts (NMFI).  
The following subsections describe interrupts:  
Interrupt request  
The IRQ exception is a normal interrupt caused by a LOW level on the nIRQ input. An IRQ  
has a lower priority than an FIQ, and is masked on entry to an FIQ sequence. You must ensure  
that the nIRQ input is held LOW until the processor acknowledges the interrupt request, either  
from the VIC interface or the software handler.  
Irrespective of whether the exception is taken from ARM state or Thumb state, an IRQ handler  
returns from the interrupt by executing:  
SUBS PC, R14_irq, #4  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-18  
       
Programmer’sModel  
You can disable IRQ exceptions within a Privileged mode by setting the CPSR.I bit to b1. See  
Program status registers on page 2-10. IRQ interrupts are automatically disabled when an IRQ  
occurs, by setting the CPSR.I bit. You can use nested interrupts but it is up to you to save any  
corruptible registers and to re-enable IRQs by clearing the CPSR.I bit.  
Fast interrupt request  
The Fast Interrupt Request (FIQ) reduces the execution time of the exception handler relative  
to a normal interrupt. FIQ mode has eight private registers to reduce, or even remove the  
requirement for register saving (minimizing the overhead of context switching).  
An FIQ is externally generated by taking the nFIQ input signal LOW. You must ensure that the  
nFIQ input is held LOW until the processor acknowledges the interrupt request from the  
software handler.  
Irrespective of whether exception entry is from ARM state or Thumb state, an FIQ handler  
returns from the interrupt by executing:  
SUBS PC, R14_fiq, #4  
If Non-Maskable Fast Interrupts (NMFIs) are not enabled, you can mask FIQ exceptions by  
setting the CPSR.F bit to b1. For more information see:  
FIQ and IRQ interrupts are automatically masked by setting the CPSR.F and CPSR.I bits when  
an FIQ occurs. You can use nested interrupts but it is up to you to save any corruptible registers  
and to re-enable interrupts.  
Non-maskable fast interrupts  
When NMFI behavior is enabled, FIQ interrupts cannot be masked by software. Enabling NMFI  
behavior ensures that when the FIQ mask, that is, the CPSR.F bit, has been cleared by the reset  
handler, fast interrupts are always taken as quickly as possible, except during handling of a fast  
interrupt. This makes the fast interrupt suitable for signaling critical events. NMFI behavior is  
controlled by a configuration input signal CFGNMFI, that is asserted HIGH to enable NMFI  
operation. There is no software control of NMFI.  
Software can detect whether NMFI operation is enabled by reading the NMFI bit of the System  
Control Register:  
NMFI == 0 Software can mask FIQs by setting the CPSR.F bit to b1.  
NMFI == 1 Software cannot mask FIQs.  
When the NMFI bit in the System Control Register is b1:  
an instruction writing b0 to the CPSR.F bit clears it to b0  
an instruction writing b1 to the CPSR.F bit leaves it unchanged  
the CPSR.F bit can be set to b1 only by an FIQ or reset exception entry.  
Low interrupt latency  
Low Interrupt Latency (LIL) is a set of behaviors that reduce the interrupt latency for the  
processor, and is enabled by default. That is, the FI bit [21] in the System Control Register is  
Read-as-One.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-19  
       
Programmer’sModel  
LIL behavior enables accesses to Normal memory, including multiword accesses and external  
accesses, to be abandoned part-way through execution so that the processor can react to a  
pending interrupt faster than would otherwise be the case. When an instruction is abandoned in  
this way, the processor behaves as if the instruction was not executed at all. If, after handling the  
interrupt, the interrupt handler returns to the program in the normal way using instruction SUBS  
pc, r14, #4, the abandoned instruction is re-executed. This means that some of the memory  
accesses generated by the instruction are performed twice.  
Memory that is marked as Strongly Ordered or Device type is typically sensitive to the number  
of reads or writes performed. Because of this, instructions that access Strongly Ordered or  
Device memory are never abandoned when they have started accessing memory. These  
instructions always complete either all or none of their memory accesses. Therefore, to  
minimize the interrupt latency, you must avoid the use of multiword load/store instructions to  
memory locations that are marked as Strongly Ordered or Device.  
Interrupt controller  
The processor includes a VIC port for connection of a Vectored Interrupt Controller (VIC). An  
interrupt controller is a peripheral that handles multiple interrupt sources. Features usually  
found in an interrupt controller are:  
multiple interrupt request inputs, one for each interrupt source, and one or more  
amalgamated interrupt request outputs to the processor  
the ability to mask out particular interrupt requests  
prioritization of interrupt sources for interrupt nesting.  
In a system with an interrupt controller with these features, software is still required to:  
determine from the interrupt controller which interrupt source is requesting service  
determine where the service routine for that interrupt source is loaded  
mask or clear that interrupt source, before re-enabling processor interrupts to allow  
another interrupt to be taken.  
A VIC does all these in hardware to reduce the interrupt latency. It supplies the starting address  
of the service routine corresponding to the highest priority asserted interrupt source directly to  
the processor. When the processor has accepted this address, it masks the interrupt so that the  
processor can re-enable interrupts without clearing the source. The PL192 VIC is an Advanced  
Microcontroller Bus Architecture (AMBA) compliant, System-on-Chip (SoC) peripheral that is  
developed, tested, and licensed by ARM for use in Cortex-R4 designs.  
You can use the VIC port to connect a PL192 VIC to the processor. See the ARM PrimeCell  
Vectored Interrupt Controller (PL192) Technical Reference Manual for more information about  
the PL192 VIC. You can enable the VIC port by setting the VE bit in the System Control  
Register. When the VIC port is enabled and an IRQ occurs, the processor performs an handshake  
over the VIC interface to obtain the address of the handling routine for the IRQ.  
See the Cortex-R4 and Cortex-R4F Integration Manual for more information about the VIC  
port, its signals, and their timings.  
Interrupt entry flowchart  
Figure 2-5 on page 2-21 is a flowchart for processor interrupt recognition. It shows all the  
necessary decisions and actions for complete interrupt entry.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-20  
 
Programmer’sModel  
Start  
!VE || VIC  
handshake  
complete  
TRUE  
FALSE  
!((nFIQ||F)  
&&  
(nIRQ||I))  
VE==1  
FALSE  
TRUE  
FALSE  
Start handshake with VIC  
TRUE  
SPSR_irq = CPSR  
LR_irq = RA+4  
!(nFIQ||F)  
TRUE  
FALSE  
CPSR[4:0] = IRQ mode  
CPSR[5] = TE  
SPSR_fiq = CPSR  
LR_fiq = RA+4  
CPSR[7] = 1  
CPSR[4:0] = FIQ mode  
CPSR[5] = TE  
V==1  
FALSE  
VE==1  
TRUE  
CPSR[7] = 1, CPSR[6] = 1  
FALSE  
Is VIC ready to  
provide handler  
address?  
V==1  
FALSE  
TRUE  
TRUE  
FALSE  
TRUE  
PC[31:0] = Handler address  
provided by VIC  
Acknowledge address to VIC  
PC[31:0] =  
0xFFFF001C  
PC[31:0] =  
0x0000001C  
PC[31:0] =  
0xFFFF0018  
PC[31:0] =  
0x00000018  
Figure 2-5 Interrupt entry sequence  
For information on the I and F bits that Figure 2-5 shows, see Program status registers on  
page 2-10. For information on the V and VE bits that Figure 2-5 shows, see c1, System Control  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-21  
   
Programmer’sModel  
2.8.4  
Aborts  
When the processor's memory system cannot complete a memory access successfully, an abort  
is generated. Aborts can occur for a number of reasons, for example:  
a permission fault indicated by the MPU  
an error response to a transaction on the AXI memory bus  
an error detected in the data by the ECC checking logic.  
An error occurring on an instruction fetch generates a prefetch abort. Errors occurring on data  
accesses generate data aborts. Aborts are also categorized as being either precise or imprecise.  
When a prefetch or data abort occurs, the processor takes the appropriate type of exception. See  
about the type of abort is stored in registers, and signaled as events. See Fault handling on  
page 8-7 for more details of the types of fault that can cause an abort and the information that  
the processor provides about these faults.  
Prefetch aborts  
When a Prefetch Abort (PABT) occurs, the processor marks the prefetched instruction as  
invalid, but does not take the exception until the instruction is to be executed. If the instruction  
is not executed, for example because a branch occurs while it is in the pipeline, the abort does  
not take place.  
All prefetch aborts are precise.  
Data aborts  
An error occurring on a data memory access can generate a data abort. If the instruction  
generating the memory access is not executed, for example, because it fails its condition codes,  
or is interrupted, the data abort does not take place.  
A Data Abort (DABT) can be either precise or imprecise, depending on the type of fault that  
caused it.  
The processor implements the base restored Data Abort model, as opposed to a base updated  
Data Abort model.  
With the base restored Data Abort model, when a Data Abort exception occurs during the  
execution of a memory access instruction, the processor hardware always restores the base  
register to the value it contained before the instruction was executed. This removes the  
requirement for the Data Abort handler to unwind any base register update that the aborted  
instruction might have specified. This simplifies the software Data Abort handler. For more  
information, see the ARM Architecture Reference Manual.  
Precise aborts  
A precise abort, also known as a synchronous abort, is one for which the exception is guaranteed  
to be taken on the instruction that generated the aborting memory access. The abort handler can  
use the value in the Link Register (r14_abt) to determine which instruction generated the abort,  
and the value in the Saved Program Status Register (SPSR_abt) to determine the state of the  
processor when the abort occurred.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-22  
   
Programmer’sModel  
Imprecise aborts  
An imprecise abort, also known as an asynchronous abort, is one for which the exception is  
taken on a later instruction to the instruction that generated the aborting memory access. The  
abort handler cannot determine which instruction generated the abort, or the state of the  
processor when the abort occurred. Therefore, imprecise aborts are normally fatal.  
Imprecise aborts can be generated by store instructions to normal-type or device-type memory.  
When the store instruction is committed, the data is normally written into a buffer that holds the  
data until the memory system has sufficient bandwidth to perform the write access. This gives  
read accesses higher priority. The write data can be held in the buffer for a long period, during  
which many other instructions can complete. If an error occurs when the write is finally  
performed, this generates an imprecise abort.  
Imprecise abort masking  
The nature of imprecise aborts means that they can occur while the processor is handling a  
different abort. If an imprecise abort generates a new exception in such a situation, the r14_abt  
and SPSR_abt values are overwritten. If this occurs before the data is pushed to the stack in  
memory, the state information about the first abort is lost. To prevent this from happening, the  
CPSR contains a mask bit to indicate that an imprecise abort cannot be accepted, the A-bit.  
When the A-bit is set, any imprecise abort that occurs is held pending by the processor until the  
A-bit is cleared, when the exception is actually taken. The A-bit is automatically set when abort,  
IRQ or FIQ exceptions are taken, and on reset. You must only clear the A-bit in an abort handler  
after the state information has either been stacked to memory, or is no longer required.  
Only one pending imprecise abort of each imprecise abort type is supported. The processor  
supports the following pending imprecise aborts:  
Imprecise external abort  
If a subsequent imprecise external abort is signaled while another one is pending, the later  
one is ignored and only one abort is taken.  
One TCM write external error for each TCM port.  
Cache write parity or ECC error.  
If a subsequent cache parity or ECC error is signaled while another one is pending, the  
later one is normally ignored and only one abort is taken. However, if the pending error  
was correctable, and the later one is not correctable, the pending error is ignored, and one  
abort is taken for the error that cannot be corrected.  
Memory barriers  
When a store instruction, or series of instructions has been executed to normal-type or  
device-type memory, it is sometimes necessary to determine whether any errors occurred  
because of these instructions. Because most of these errors are reported imprecisely, they might  
not generate an abort exception until some time after the instructions are executed. To ensure  
that all possible errors have been reported, you must execute a DSBinstruction. Abort exceptions  
are only taken because of these errors if they are not masked, that is, the CPSR A-bit is clear. If  
the A-bit is set, the aborts are held pending.  
Aborts in Strongly Ordered and Device memory  
When a memory access generates an abort, the instruction generating that access is abandoned,  
even if it has not completed all its memory accesses, and the abort exception is taken. The abort  
handler can then do one of the following:  
fix the error and return to the instruction that was abandoned, to re-execute it  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-23  
 
Programmer’sModel  
perform the appropriate data transfers on behalf of the aborted instruction and return to  
the instruction after the abandoned instruction  
treat the error as fatal and terminate the process.  
If the abort handler returns to the abandoned instruction, some of the memory accesses  
generated are repeated. The effect is that multiword load/store instructions can access the same  
memory location twice. The first access occurs before the abort is detected, and the second when  
the instruction is restarted.  
In Strongly Ordered or Device type memory, repeating memory accesses might have  
unacceptable side-effects. Therefore, if the abort handler can fix the error and re-execute the  
aborted instruction, you must ensure that for all memory errors on multiword load/store  
instructions, either:  
all side effects of repeating accesses are inconsequential  
the error must either occur on the first word accessed or not at all.  
The instructions that this rule applies to are:  
All forms of ARM instructions LDM, and LDRD, all forms of STM  
variants, and unaligned LDR  
,
STRDincluding VFP  
,
STR, LDRH, and STRH  
Thumb instructions LDMIA  
,
LDRD  
,
SDRD, PUSH, POP, and STMIAincluding VFP variants, and  
unaligned LDR  
,
STR  
,
LDRH, and STRH.  
Abort handler  
If you configure the processor with parity or ECC on the caches or the TCMs, and the abort  
handler is in one of these memories, then it is possible for a parity or ECC error to occur in the  
abort handler. If the error is not recoverable, then a precise abort occurs and the processor loops  
until the next interrupt. The LR and SPSR values for the original abort are also lost. Therefore,  
you must construct software that ensures that no precise aborts occur when in the abort handler.  
This means the abort handler must be in external memory and not cached.  
2.8.5  
Supervisor call instruction  
You can use the SuperVisor Call (SVC) instruction (formerly SWI) to enter Supervisor mode,  
usually to request a particular supervisor function. The SVC handler reads the opcode to extract  
the SVC function number. A SVC handler returns by executing the following instruction,  
irrespective of the processor operating state:  
MOVS PC, R14_svc  
This action restores the PC and CPSR, and returns to the instruction following the SVC.  
IRQs are disabled when a software interrupt occurs.  
The processor modifies the IT execution state bits on exception entry so that the values that the  
processor writes into the SPSR are correct for the instruction following the SVC. This means  
that the SVC handler does not have to perform any special action to accommodate the IT  
instruction. For more information on the IT instruction, see the ARM Architecture Reference  
Manual.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-24  
 
Programmer’sModel  
2.8.6  
Undefined instruction  
When an instruction is encountered which is UNDEFINED, or is for the VFP when the VFP is  
not enabled, the processor takes the Undefined instruction exception. Software can use this  
mechanism to extend the ARM instruction set by emulating UNDEFINED coprocessor  
instructions. UNDEFINED exceptions also occur when a UDIVor SDIVinstruction is executed,  
the value in Rm is zero, and the DZ bit in the System Control Register is set.  
If the handler is required to return after the instruction that caused the Undefined exception, it  
must:  
Advance the IT execution state bits in the SPSR before restoring SPSR to CPSR. This is  
so that the correct condition codes are applied to the next instruction on return. The  
pseudo-code for advancing the IT bits is:  
Mask = SPSR[11,10,26,25];  
if (Mask != 0) {  
Mask = Mask << 1;  
SPSR[12,11,10,26,25] = Mask;  
}
if (Mask[3:0] == 0) {  
SPSR[15:12] = 0;  
}
Obtain the instruction that caused the Undefined exception and return correctly after it.  
Exception handlers must also be aware of the potential for both 16-bit and 32-bit  
instructions in Thumb state.  
After testing the SPSR and determining the instruction was executed in Thumb state, the  
Undefined handler must use the following pseudo-code or equivalent to obtain this  
information:  
addr = R14_undef - 2  
instr = Memory[addr,2]  
if (instr >> 11) > 28 { /* 32-bit instruction */  
instr = (instr << 16) | Memory[addr+2,2]  
if (emulating, so return after instruction wanted) }  
R14_undef += 2 //  
} //  
}
After this, instrholds the instruction (in the range 0x0000  
0xFFFFFFFFfor a 32-bit instruction), and the exception can be returned from  
using a MOVS PC, R14to return after it.  
-0xE7FFfor a 16-bit instruction,  
0xE8000000  
-
IRQs are disabled when an Undefined instruction trap occurs. For more information about  
Undefined instructions, see the ARM Architecture Reference Manual.  
2.8.7  
Breakpoint instruction  
A breakpoint (BKPT) instruction operates as though the instruction causes a Prefetch Abort.  
A breakpoint instruction does not cause the processor to take the Prefetch Abort exception until  
the instruction is to be executed. If the instruction is not executed, for example because a branch  
occurs while it is in the pipeline, the breakpoint does not take place.  
After dealing with the breakpoint, the handler executes the following instruction irrespective of  
the processor operating state:  
SUBS PC, R14_abt, #4  
This action restores both the PC and the CPSR, and retries the breakpointed instruction.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-25  
   
Programmer’sModel  
Note  
If the EmbeddedICE-RT logic is configured into Halt debug-mode, a breakpoint instruction  
causes the processor to enter debug state. See Halting debug-mode debugging on page 11-3.  
2.8.8  
Exception vectors  
You can configure the location of the exception vector addresses by setting the V bit in CP15 c1  
System Control Register to enable HIVECS, as Table 2-5 shows.  
Table 2-5 Configuration of exception vector address locations  
Exception vector  
Value of V bit  
base location  
0
0x00000000  
0xFFFF0000  
1 (HIVECS)  
Table 2-6 shows the exception vector addresses and entry conditions for the different exception  
types.  
Table 2-6 Exception vectors  
Offset from  
Exception  
Mode on entry A bit on entry F bit on entry I bit on entry  
vector base  
Reset  
0x00  
0x04  
0x08  
0x0C  
0x10  
0x18  
0x1C  
Supervisor  
Undefined  
Supervisor  
Abort  
Set  
Set  
Set  
Set  
Set  
Set  
Set  
Set  
Set  
Undefined instruction  
Software interrupt  
Abort (prefetch)  
Abort (data)  
IRQ  
Unchanged  
Unchanged  
Unchanged  
Unchanged  
Unchanged  
Unchanged  
Set  
Unchanged  
Set  
Set  
Set  
Set  
Abort  
IRQ  
FIQ  
FIQ  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-26  
         
Programmer’sModel  
2.9  
Acceleration of execution environments  
Because the ARMv7-R architecture requires Jazelle® software compatibility, three Jazelle  
registers are implemented in the processor.  
Table 2-7 shows the Jazelle register instruction summary and the response to the instructions.  
Table 2-7 Jazelle register instruction summary  
Register  
Instruction  
Response  
Jazelle ID  
MRC p14, 7, <Rd>, c0, c0, 0  
MCR p14, 7, <Rd>, c0, c0, 0  
Read as zero  
Ignore writes  
Jazelle main configuration  
Jazelle OS control  
MRC p14, 7, <Rd>, c2, c0, 0  
MCR p14, 7, <Rd>, c2, c0, 0  
Read as zero  
Ignore writes  
MRC p14, 7, <Rd>, c1, c0, 0  
MCR p14, 7, <Rd>, c1, c0, 0  
Read as zero  
Ignore writes  
Note  
Because no hardware acceleration is present in the processor, when the BXJinstruction is used,  
the BXinstruction is invoked.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-27  
       
Programmer’sModel  
2.10 Unaligned and mixed-endian data access support  
The processor supports unaligned memory accesses. Unaligned memory accesses was  
introduced with ARMv6. Bit [22] of c1, Control Register is always 1.  
The processor supports byte-invariant big-endianness BE-8 and little-endianness LE. The  
processor does not support word-invariant big-endianness BE-32. Bit [7] of c1, Control Register  
is always 0.  
For more information on unaligned and mixed-endian data access support, see the ARM  
Architecture Reference Manual.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-28  
   
Programmer’sModel  
2.11 Big-endian instruction support  
The processor supports little-endian or big-endian instruction format, and is dependent on the  
setting of the CFGIE pin. This is reflected in bit [31] of the System Control Register. For more  
Note  
The facility to use big-endian or little-endian instruction format is an implementation option,  
and you can therefore remove it in specific implementations. If this facility is not present, the  
CFGIE pin is still reflected in the System Control Register but the instruction format is always  
little-endian.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
2-29  
   
Chapter 3  
Processor Initialization, Resets, and Clocking  
Before you can run application software on the processor, it must be reset and initialized, including  
loading the appropriate software-configuration. This chapter describes the signals for clocking and  
resetting the processor, and the steps that the software must take to initialize the processor after  
reset. It contains the following sections:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
3-1  
   
Processor Initialization, Resets, and Clocking  
3.1  
Initialization  
Most of the architectural registers in the processor, such as r0-r14, and s0-s31 and d0-d15 when  
floating-point is included, are not reset. Because of this, you must initialize these for all modes  
before they are used, using an immediate-MOV instruction, or a PC-relative load instruction.  
The Current Program Status Register (CPSR) is given a known value on reset. This is described  
in the ARM Architecture Reference Manual. The reset values for the CP15 registers are  
described along with the registers in Chapter 4 System Control Coprocessor.  
In addition, before you run the application, you might want to:  
program particular values into various registers, for example, stack pointers  
enable various processor features, for example, error correction  
program particular values into memory, for example, the TCMs.  
Other initialization requirements are described in:  
3.1.1  
MPU  
If the processor has been built with an MPU, before you can use it you must:  
program and enable at least one of the regions  
enable the MPU in the System Control Register.  
unless at least one MPU region is programmed and active. If the MPU is enabled, before using  
the TCM interfaces you must program MPU regions to cover the TCM regions to give access  
permissions to them.  
3.1.2  
CRS  
In processor revisions r1p2 and earlier the Call-Return-Stack (CRS) in the PFU is not reset. This  
means it contains UNPREDICTABLE data after reset. ARM recommends that you initialize the  
CRS before it is used. For more information on the PFU, see Chapter 5 Prefetch Unit,  
To do this, before any return instructions are executed, such as BX LDR pc, or LDM pc, execute  
,
four branch-and-link instructions, as follows:  
; Initialise call-return-stack (CRS) with four call instructions.  
BL call1  
call1  
call2  
call3  
next  
BL call2  
BL call3  
BL next  
3.1.3  
FPU  
If the processor has been built with a Floating Point Unit (FPU) you must enable it before VFP  
instructions can be executed:  
enable access to the FPU in the coprocessor access control register, see c1, Coprocessor  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
3-2  
         
Processor Initialization, Resets, and Clocking  
enable the FPU by setting the EN-bit in the FPEXC register, see Floating-Point Exception  
Note  
Floating-point logic is only available with the Cortex-R4F processor.  
3.1.4  
Caches  
If the processor has been built with instruction or data caches, these must be invalidated before  
they are enabled, otherwise UNPREDICTABLE behavior can occur. See Cache operations on  
If you are using an error checking scheme in the cache, you must enable this by programming  
the auxiliary control register as described in Auxiliary Control Registers on page 4-38 before  
invalidating the cache, to ensure that the correct error code or parity bits are calculated when the  
cache is invalidated. An invalidate all operation never reports any ECC or parity errors.  
3.1.5  
TCM  
The processor does not initialize the TCM RAMs. It is not essential to initialize all the memory  
attached to the TCM interface but ARM recommends that you do. In addition, you might want  
to preload instructions or data into the TCM for the main application to use. This section  
describes various ways that you can perform data preloading. You can also configure the  
processor to use the TCMs from reset.  
Preloading TCMs  
You can write data to the TCMs using either store instructions or the AXI slave interface.  
Depending on the method you choose, you might require:  
particular hardware on the SoC that you are using  
boot code  
a debugger connected to the processor.  
Methods to preload TCMs include:  
Memory copy with running boot code  
The boot code includes a memory copy routine that reads data from a ROM, and  
writes it into the appropriate TCM. You must enable the TCM to do this, and it  
might be necessary to give the TCM one base address while the copy is occurring,  
and a different base address when the application is being run.  
Copy data from the debug communications channel  
The boot code includes a routine to read data from the Debug Communications  
Channel (DCC) and write it into the TCM. The debug host feeds the data for this  
operation into the DCC by writing to the appropriate registers on the processor  
APB debug port.  
Execute code in debug halt state  
The processor is put into debug halt state by the debug host, which then feeds  
instructions into the processor through the Instruction Transfer Register (ITR).  
The processor executes these instructions, which replace the boot code in either  
of the two methods described above.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
3-3  
     
Processor Initialization, Resets, and Clocking  
DMA into TCM  
The SoC includes a Direct Memory Access (DMA) device that reads data from a  
ROM, and writes it to the TCMs through the AXI slave interface.  
Write to TCM directly from debugger  
A Debug Access Port (DAP) in the system is used to generate AMBA  
transactions to write data into the TCMs through the AXI slave interface. This  
DAP is controlled from the debug host through a JTAG chain.  
Preloading TCMs with parity or ECC  
The error code or parity bits in the TCM RAM, if configured with an error scheme, are not  
initialized by the processor. Before a RAM location is read with ECC or parity checking  
enabled, the error code or parity bits must be initialized. To calculate the error code or parity bits  
correctly, the logic must have all the data in the data chunk that those bits protect. Therefore,  
when the TCM is being initialized, the writes must be of the same width and aligned to the data  
chunk that the error scheme protects.  
You can initialize the TCM RAM with error checking turned on or off, according to the rules  
below see. See Auxiliary Control Registers on page 4-38. The error code or parity bits written  
to the TCM are valid even if the error checking is turned off.  
If the slave port is used, write transactions must be used that write to the TCM memory as  
follows:  
If the error scheme is parity, any write transaction can be used.  
If the error scheme is 32-bit ECC, the write transactions must start at a 32-bit aligned  
addresses and write a continuous block of memory, containing a multiple of 4 bytes. All  
bytes in the block must be written, that is, have their byte lane strobe asserted.  
If the error scheme is 64-bit ECC, the write transactions must start at a 64-bit aligned  
addresses and write a continuous block of memory, containing a multiple of 8 bytes. All  
bytes in the block must be written, that is, have their byte lane strobe asserted.  
If initialization is done by running code on the processor, this is best done by a loop of stores  
that write to the whole of the TCM memory as follows:  
If the error scheme is parity, or no error scheme, any store instruction can be used.  
If the scheme is 32-bit ECC, use Store Word (STR), Store Two Words (STRD), or Store  
Multiple Words (STM) instructions to 32-bit aligned addresses.  
If the scheme is 64-bit ECC, use STRD or STM, that has an even number of registers in  
the register list, with a 64-bit aligned starting address.  
Note  
You can use the alignment-checking features of the processor to help you ensure that memory  
accesses are 32-bit aligned, but there is no checking for 64-bit alignment. If you are using STRD  
or STM, an alignment fault is generated if the address is not 32-bit aligned. For the same  
behavior with STRinstructions, enable strict-alignment-checking by setting the A-bit in the  
If the error scheme is 64-bit ECC, a simpler way to initialize the TCM is:  
Turn off error checking.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
3-4  
Processor Initialization, Resets, and Clocking  
Turn on 64-bit store behavior using CP15. See c15, Secondary Auxiliary Control Register  
Write to the TCM using any store instructions, or any AXI write transactions. The  
processor performs read-modify-write accesses to ensure that all writes are to 64-bit  
aligned quantities, even though error checking is turned off.  
Note  
You can enable error checking and 64-bit store behavior on a per-TCM interface basis.  
References above to these controls relate to whichever TCM is being initialized.  
Using TCMs from reset  
The processor can be pin-configured to enable the TCM interfaces from reset, and to select the  
address at which each TCM appears from reset. See TCM initialization on page 8-16 for more  
details. This enables you to configure the processor to boot from TCM but, to do this, the TCM  
must first be preloaded with the boot code. The nCPUHALT pin can be asserted while the  
processor is in reset to stop the processor from fetching and executing instructions after coming  
out of reset. While the processor is halted in this way, the TCMs can be preloaded with the  
appropriate data. When the nCPUHALT pin is deasserted, the processor starts fetching  
instructions from the reset vector address in the normal way.  
Note  
When it has been deasserted to start the processor fetching, nCPUHALT must not be asserted  
again except when the processor is under processor or power-on reset, that is, nRESET  
asserted. The processor does not halt if the nCPUHALT pin is asserted while the processor is  
running.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
3-5  
Processor Initialization, Resets, and Clocking  
3.2  
Resets  
The processor has the following reset inputs:  
nRESET  
This signal is the main processor reset that initializes the majority of the  
processor logic.  
PRESETDBGn  
This signal resets processor debug logic and CoreSight ETM-R4.  
nSYSPORESET This signal is the reset that initializes the entire processor, including CP14  
debug logic and the APB debug logic. See CP14 registers reset on page  
11-23 for information.  
nCPUHALT  
This signal stops the processor from fetching instructions after reset.  
All of these are active-LOW signals that reset logic in the processor. You must take care when  
designing the logic to drive these reset signals.  
The processor synchronizes the resets to the relevant clock domains internally.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
3-6  
   
Processor Initialization, Resets, and Clocking  
3.3  
Reset modes  
The reset signals in the processor enable you to reset different parts of the design independently.  
Table 3-1 shows the reset signals, and the combinations and possible applications that you can  
use them in.  
Table 3-1 Reset modes  
Reset mode  
nRESET PRESETDBGn nSYSPORESET nCPUHALT Application  
Power-on reset  
0
0
x
x
0
1
x
x
Reset at power up, full system  
reset. Hard reset or cold reset.  
Processor reset  
Reset of processor only,  
watchdog reset. Soft reset or  
warm reset.  
Normal  
Halt  
1
1
x
x
1
1
1
0
Normal run mode.  
Halt mode, provided normal  
mode has not been entered  
since reset.  
Debug reset  
x
0
x
x
Resets all debug logic and  
debug APB interface.  
Note  
If nRESET is set to 1 and nSYSPORESET is set to 0 the behavior is architecturally  
Unpredictable.  
This section of the manual describes:  
3.3.1  
Power-on reset  
You must apply power-on or cold reset to the processor when power is first applied to the  
system. In the case of power-on reset, the leading, or falling, edge of the reset signals, nRESET  
and nSYSPORESET, does not have to be synchronous to CLKIN. Because the nRESET and  
nSYSPORESET signals are synchronized within the processor, you do not have to synchronize  
these signals. Figure 3-1 shows the application of power-on reset.  
CLKIN  
nRESET  
nSYSPORESET  
Figure 3-1 Power-on reset  
ARM recommends that you assert the reset signals for at least four CLKIN cycles to ensure  
correct reset behavior.  
It is not necessary to assert PRESETDBGn on power-up.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
3-7  
             
Processor Initialization, Resets, and Clocking  
3.3.2  
Processor reset  
A processor or warm reset initializes the majority of the processor, excluding the  
EmbeddedICE-RT logic. Processor reset is typically used for resetting a system that has been  
operating for some time, for example, watchdog reset.  
Because the nRESET signal is synchronized within the processor, you do not have to  
synchronize this signal.  
3.3.3  
3.3.4  
Normal operation  
During normal operation, neither processor reset nor power-on reset is asserted. If the  
Embedded ICE-RT is not used, the value of PRESETDBGn does not matter.  
Halt operation  
When nCPUHALT is asserted, and nSYSPORESET and nRESET deasserted, the processor  
is out of reset, but the PFU is inhibited from fetching instructions. For example, you can use  
nCPUHALT to enable DMA into the TCMs using the processor. You can then deassert  
nCPUHALT and the PFU starts fetching instructions from TCMs. When the processor has  
started fetching, nCPUHALT must not be asserted again except when the processor is reset.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
3-8  
     
Processor Initialization, Resets, and Clocking  
3.4  
Clocking  
The processor has two functional clock inputs. Externally to the processor, you must connect  
together CLKIN and FREECLKIN.  
In addition, there is the PCLKDBG clock for the debug APB bus. This is asynchronous to the  
main clock.  
All clocks can be stopped indefinitely without loss of state.  
Three additional clock inputs, CLKIN2, DUALCLKIN, and DUALCLKIN2, are related to  
the dual-redundant core functionality, if included. If you are integrating a Cortex-R4 macrocell  
with dual-redundant core, contact the implementer of that macrocell for information about how  
to connect the clock inputs.  
The following is described in this section:  
3.4.1  
AXI interface clocking  
The AXI master and AXI slave interfaces must be connected to AXI systems that are  
synchronous to the processor clock, CLKIN, even if this might be at a lower frequency. This  
means that every rising edge on the AXI system clock must be synchronous to a rising edge on  
CLKIN.  
The AXI master interface clock enable signal ACLKENM and the AXI slave interface clock  
enable signal ACLKENS must be asserted on every CLKIN rising edge for which there is a  
simultaneous rising edge on the AXI system clock.  
Figure 3-2 shows an example in which the processor is clocked at 400MHz (CLKIN), while the  
AXI system connected to the AXI master interface is clocked at 200MHz (ACLKM). The  
ACLKENM clock indicates the relationship between the two clocks.  
CLKIN  
ACLKM  
ACLKENM  
Figure 3-2 AXI interface clocking  
If the AXI system connected to an interface is clocked at the same frequency as the processor,  
then the corresponding clock enable signal must be tied HIGH.  
3.4.2  
Clock gating  
You can use the STANDBYWFI output to gate the clock to the TCMs when the processor is in  
Standby mode. If you do, you must design the logic so that the TCM clock starts running within  
four cycles of STANDBYWFI going LOW.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
3-9  
               
Chapter 4  
System Control Coprocessor  
This chapter describes the purpose of the system control coprocessor, its structure, operation, and  
how to use it. It contains the following sections:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-1  
   
System Control Coprocessor  
4.1  
About the system control coprocessor  
This section gives an overview of the system control coprocessor. For more information of the  
registers in the system control coprocessor, see System control coprocessor registers on  
The purpose of the system control coprocessor, CP15, is to control and provide status  
information for the functions implemented in the processor. The main functions of the system  
control coprocessor are:  
overall system control and configuration  
cache configuration and management  
Memory Protection Unit (MPU) configuration and management  
system performance monitoring.  
The system control coprocessor does not exist in a distinct physical block of logic.  
System control coprocessor functional groups  
4.1.1  
The system control coprocessor appears as a set of registers that you can write to and read from.  
Some of the registers permit more than one type of operation. The functional groups for the  
registers are:  
Table 4-1 on page 4-3 shows the overall functionality for the system control coprocessor,  
provided through the registers. The registers are listed in their functional groups.  
Table 4-2 on page 4-9 lists the registers in the system control processor, in register order, and  
gives the reset value for each register.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-2  
   
System Control Coprocessor  
Table 4-1 System control coprocessor register functions  
Reference to description  
Function  
Register/operation  
System control and  
configuration  
Control  
Auxiliary control  
Coprocessor Access Control  
Main IDa  
Product Feature IDs  
Multiprocessor ID  
Slave Port Control  
Context ID  
FCSE PID  
Software compatibility Thread And Process ID  
MPU control and  
configuration  
Data Fault Status  
Auxiliary Fault Status  
Instruction Fault Status  
Instruction Fault Address  
Data Fault Address  
MPU Type  
Region Base Address  
Region Size and Enable  
Region Access Control  
Memory Region Number  
Cache Type  
Cache control and  
configuration  
Current Cache Size  
Identification  
Current Cache Level  
Cache Size Selection  
c7, Cache Operations  
c15, Invalidate all data cache  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-3  
   
System Control Coprocessor  
Table 4-1 System control coprocessor register functions (continued)  
Function  
Register/operation  
Reference to description  
TCM control and  
configuration  
TCM Status  
Region  
System performance  
monitoring  
Performance monitoring  
System validation  
Validation  
a. Known as the ID Code Register on previous designs. Returns the device ID code.  
4.1.2  
System control and configuration  
The system control and configuration registers provide overall management of:  
memory functionality  
interrupt behavior  
exception handling  
program flow prediction  
coprocessor access rights for CP0-CP13, including the VFP, CP10-11.  
The system control and configuration registers also provide the processor ID and information  
on configured options.  
The system control and configuration registers consist of 18 read-only registers and seven  
read/write registers. Figure 4-1 shows the arrangement of registers in this functional group.  
CRn  
c0  
Opcode_1  
0
CRm Opcode_2  
c0  
0
Main ID Register  
5
Multiprocessor ID Register  
Processor Feature Registers 0, 1  
Debug Feature Register 0  
Auxiliary Feature Register 0  
Memory Model Feature Registers 0 - 3  
Instruction Set Attributes Registers 0 - 5  
System Control Register  
Auxiliary Control Register  
Coprocessor Access Register  
Slave Port Control Register  
FCSE PID Register  
c1  
{0, 1}  
2
3
{4–7}  
{0-5}  
0
1
2
0
0
1
0
0
1
c2  
c0  
c1  
0
c11  
c13  
0
0
c0  
c0  
Context ID Register  
Secondary Auxiliary Control Register  
Build Options Register 1  
0
c0  
c2  
c15  
Build Options Register 2  
Read-only  
Read/write  
Write-only  
Accessible in User mode  
Figure 4-1 System control and configuration registers  
Some of the functionality depends on how you set external signals at reset.  
System control and configuration behaves in three ways:  
as a set of flags or enables for specific functionality  
as a set of numbers, with values that indicate system functionality  
as a set of addresses for processes in memory.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-4  
       
System Control Coprocessor  
4.1.3  
MPU control and configuration  
The MPU control and configuration registers:  
control program access to memory  
designate areas of memory as either:  
Normal, Non-cacheable  
Normal, Cacheable  
Device  
Strongly Ordered.  
detect MPU faults and external aborts.  
The MPU control and configuration registers consist of one read-only register and eleven  
read/write registers. Figure 4-2 shows the arrangement of registers in this functional group.  
CRn  
Opcode_1  
CRm Opcode_2  
c0  
c5  
0
0
c0  
c0  
4
0
MPU Type Register  
Data Fault Status Register  
1
0
1
0
2
0
2
4
0
0
Instruction Fault Status Register  
Auxilary Data Fault Status Register  
Auxilary Instruction Fault Status Register  
Data Fault Address Register  
Instruction Fault Address Register  
Region Base Register  
Region Size and Enable Register  
Region Access Control Register  
Memory Region Number Register  
Correctable Fault Location Register  
c1  
c0  
c1  
c6  
0
c2  
c3  
c15  
0
Read-only  
Read/write  
Write-only  
Accessible in User mode  
Figure 4-2 MPU control and configuration registers  
MPU control and configuration can behave:  
as a set of numbers, with values that describe aspects of the MPU or indicate its current  
state  
as a set of operations that act on the MPU.  
4.1.4  
Cache control and configuration  
The cache control and configuration registers:  
provide information on the size and architecture of the instruction and data caches  
control cache maintenance operations that include clean and invalidate caches, drain and  
flush buffers, and address translation  
override cache behavior during debug or interruptible cache operations.  
The cache control and configuration registers consist of three read-only registers, one read/write  
register, and a number of write-only registers. Figure 4-3 on page 4-6 shows the arrangement of  
the registers in this functional group.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-5  
         
System Control Coprocessor  
CRn  
c0  
Opcode_1  
CRm Opcode_2  
0
1
c0  
c0  
1
0
1
0
0
Cache Type Register  
Current Cache Size Identification Register  
Current Cache Level Identification Register  
Cache Size Selection Register  
Cache Operations Registers ‡  
Invalidate all Data Cache Register  
2
0
0
c0  
c7  
c15  
c5  
Read-only  
Read/write  
Write-only  
Accessible in User mode  
See description of cache operations  
for operations with User mode access  
† See description of cache operations for  
implemented CRm and Opcode_2 values  
Figure 4-3 Cache control and configuration registers  
Cache control and configuration registers behave as:  
a set of numbers, with values that describe aspects of the caches  
a set of bits that enable specific cache functionality  
a set of operations that act on the caches.  
4.1.5  
TCM control and configuration  
The TCM control and configuration registers:  
inform the processor about the status of the TCM regions  
define TCM regions.  
The TCM control and configuration registers consist of two read-only registers and two  
read/write registers. Figure 4-4 shows the arrangement of registers.  
CRn  
Opcode_1  
CRm Opcode_2  
TCM Type Register  
c0  
c9  
0
0
c0  
c1  
2
0
1
0
BTCM Region Register  
ATCM Region Register  
TCM Selection Register  
c2  
Read-only  
Read/write  
Write-only  
Accessible in User mode  
Figure 4-4 TCM control and configuration registers  
TCM control and configuration behaves in three ways:  
as a set of numbers, with values that describe aspects of the TCMs  
as a set of bits that enable specific TCM functionality  
as a set of addresses that define the memory locations of data stored in the TCMs.  
4.1.6  
System performance monitor  
The performance monitor registers:  
control the monitoring operation  
count events.  
The system performance monitor consists of 12 read/write registers. Figure 4-5 on page 4-7  
shows the arrangement of registers in this functional group.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-6  
           
System Control Coprocessor  
CRn  
c9  
Opcode_1  
0
CRm Opcode_2  
c12  
0
1
2
3
4
5
0
1
2
0
1
2
Performance Monitor Control Register †  
Count Enable Set Register †  
Count Enable Clear Register †  
Overflow Flag Status Register †  
Software Increment Register †  
Performance Counter Selection Register †  
Cycle Count Register †  
Event Select Register †  
Performance Count Register †  
User Enable Register  
0
0
c13  
c14  
Interrupt Enable Set Register  
Interrupt Enable Clear Register  
Read-only  
Read/write  
Write-only  
Accessible in User mode  
† If enabled in User  
Enable Register  
Figure 4-5 System performance monitor registers  
System performance monitoring counts system events, such as cache misses, pipeline stalls, and  
other related features to enable system developers to profile the performance of their systems.  
It can generate interrupts when the number of events reaches a given value.  
For more information on the programmer’s model of the performance counters see the ARM  
Architecture Reference Manual.  
See Chapter 6 Events and Performance Monitor for more information on the registers.  
4.1.7  
System validation  
The system validation registers extend the use of the system performance monitor registers to  
provide some functions for validation. You must not use them for other purposes. The system  
validation registers schedule and clear:  
resets  
interrupts  
fast interrupts  
external debug requests.  
The system validation registers consist of nine read/write registers and one write-only register.  
Figure 4-6 shows the arrangement of registers.  
CRn  
c15  
Opcode_1  
0
CRm Opcode_2  
c1  
0
nVAL IRQ Enable Set Register †  
1
nVAL FIQ Enable Set Register †  
2
3
4
5
6
7
0
nVAL Reset Enable Set Register †  
nVAL Debug Request Enable Set Register †  
nVAL IRQ Enable Clear Register †  
nVAL FIQ Enable Clear Register †  
nVAL Reset Enable Clear Register †  
nVAL Debug Request Enable Clear Register †  
Cache size override register  
0
c14  
Read-only  
Read/write  
Write-only  
Accessible in User mode  
† If enabled in User  
Enable Register  
Figure 4-6 System validation registers  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-7  
         
System Control Coprocessor  
You can only change the cache size to a size supported by the cache RAMs implemented in your  
design.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-8  
System Control Coprocessor  
4.2  
System control coprocessor registers  
This section describes all of the registers in the system control coprocessor. The section presents  
a summary of the registers and descriptions in register order of CRn, Opcode_1, CRm,  
Opcode_2.  
For more information on using the system control coprocessor and the general method of how  
to access CP15 registers, see the ARM Architecture Reference Manual.  
4.2.1  
Register allocation  
Table 4-2 shows a summary of address allocation and reset values for the registers in the system  
control coprocessor where:  
CRn is the register number within CP15  
Op1 is the Opcode_1 value for the register  
CRm is the operational register  
Op2 is the Opcode_2 value for the register.  
Table 4-2 Summary of CP15 registers and operations  
CRn  
Op1 CRm  
Op2  
{0, 3, 6-7} Main ID  
Cache Type  
Register or operation  
Type  
Reset value  
Page  
a
c0  
0
c0  
Read-only  
Read-only  
Read-only  
Read-only  
Read-only  
Read-only  
Read-only  
Read-only  
Read-only  
Read-only  
Read-only  
Read-only  
Read-only  
0x41xFC14x  
1
2
4
5
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6-7  
0x8003C003  
0x00010001  
TCM Type  
b
MPU Type  
0x00000000  
Multiprocessor ID  
Processor Feature 0  
Processor Feature 1  
Debug Feature 0  
0x00000000  
0x00000131  
0x00000001  
0x00010400  
0x00000000  
0x00210030  
0x00000000  
0x01200000  
0x00000011  
0x01101111  
0x13112111  
0x21232131  
0x01112131  
0x00010142  
0x00000000  
0x00000000  
c1  
Auxiliary Feature 0  
Memory Model Feature 0  
Memory Model Feature 1  
Memory Model Feature 2  
Memory Model Feature 3  
c2  
c2  
Instruction Set Attributes 0 Read-only  
Instruction Set Attributes 1 Read-only  
Instruction Set Attributes 2 Read-only  
Instruction Set Attributes 3 Read-only  
Instruction Set Attributes 4 Read-only  
Instruction Set Attributes 5 Read-only  
c0  
0
Reserved, Read As Zero  
Read-only  
(RAZ)  
c3-c7  
0-7  
Reserved, RAZ  
Read-only  
0x00000000  
-
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-9  
         
System Control Coprocessor  
Table 4-2 Summary of CP15 registers and operations (continued)  
CRn  
Op1 CRm  
Op2  
Register or operation  
Type  
Reset value  
Page  
c8-c15  
0-7  
0
Undefined  
-
-
-
cd  
1
c0  
Current Cache Size ID  
Current Cache Level ID  
Undefined  
Read-only  
Read-only  
-
-
-
c
1
0x09000003  
2-7  
0-7  
0
-
c1-c15  
c0  
2
0
Cache Size Selection  
System Control  
Auxiliary Control  
Coprocessor Access  
Undefined  
Read/write  
Read/write  
Read/write  
Read/write  
-
Unpredictable  
-
d
c1  
c0  
0
-
d
1
-
2
0x00000000  
3-7  
0-7  
0-7  
0
-
c1-c15  
c0-c15  
c0  
c2-c4  
c5  
0
0
Data Fault Status  
Instruction Fault Status  
Undefined  
Read/write  
Read/write  
-
Unpredictable  
Unpredictable  
-
-
1
2-7  
0
c1  
c1  
Auxiliary Data Fault Status Read/write  
Unpredictable  
Unpredictable  
c5  
c6  
0
0
1
Auxiliary Instruction Fault  
Status  
Read/write  
2-7  
0-7  
0
Undefined  
-
-
-
c2-c15  
c0  
Data Fault Address  
Undefined  
Read/write  
Unpredictable  
1
-
-
-
2
Instruction Fault Address  
Undefined  
Read/write  
-
Unpredictable  
3-7  
0
-
-
c1  
MPU Region Base Address Read/write  
0x00000000  
-
-
1
Undefined  
-
2
MPU Region Size and  
Enable  
Read/write  
0x00000000  
3
4
Undefined  
-
-
-
MPU Region Access  
Control  
Read/write  
0x00000000  
5-7  
0
Undefined  
-
-
-
c2  
MPU Memory Region  
Number  
Read/write  
0x00000000  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-10  
   
System Control Coprocessor  
Table 4-2 Summary of CP15 registers and operations (continued)  
CRn  
Op1 CRm  
Op2  
Register or operation  
Type  
Reset value  
Page  
1-7  
1-7  
0-3  
4
Undefined  
-
-
-
c3-c15  
c7  
0
c0  
Undefined  
-
-
-
-
NOP, previously Wait For  
Interrupt  
Write-only  
5-7  
0-7  
0
Undefined  
-
-
-
c1-c4  
c5  
Invalidateentireinstruction Write-only  
cache  
-
-
c7  
0
c5  
1
Invalidateinstructioncache Write-only  
line by address to  
Point-of-Unification.  
2-3  
4
Undefined  
-
-
-
-
-
-
Flush prefetch buffer  
Undefined  
Write-only  
-
-
5
6
Invalidate entire branch  
predictor array  
Write-only  
7
Invalidate address from  
branch predictor array  
Write-only  
-
c6  
0
1
Undefined  
-
-
-
-
Invalidate data cache line  
by physical address  
Write-only  
2
Invalidate data cache line  
by Set/Way  
Write-only  
-
-
-
-
3-7  
0-7  
0
Undefined  
c7-9  
c10  
1
Clean data cache line by  
physical address  
Write-only  
Write-only  
-
-
2
Clean data cache line by  
Set/Way  
3
4
Undefined  
-
-
-
-
Data Synchronization  
Barrier  
Write-only  
5
Data Memory Barrier  
Undefined  
Write-only  
-
-
-
-
6-7  
0
c11  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-11  
System Control Coprocessor  
Table 4-2 Summary of CP15 registers and operations (continued)  
CRn  
Op1 CRm  
Op2  
Register or operation  
Type  
Reset value  
Page  
c7  
0
c11  
1
Clean data cache line by  
physical address to  
Write-only  
-
Point-of-Unification  
2-7  
Undefined  
-
-
-
-
c12-c13 0-7  
c14  
0
1
Clean and invalidate data  
cache line by physical  
address to  
Write-only  
Point-of-Unification  
c14  
2
Clean and invalidate data  
cache line by Set/Way  
Write-only  
-
-
-
-
3-7  
0-7  
0-7  
0-7  
0
Undefined  
c15  
c0-c15  
c0  
c8  
c9  
0
0
Undefined  
-
-
-
-
Undefined  
-
-
d
c1  
BTCM Region  
ATCM Region  
Undefined  
Read/write  
-
d
1
Read/write  
-
2-7  
0
-
-
-
c2  
TCM selection  
Undefined  
Read/write  
-
0x00000000  
-
1-7  
0-7  
0
-
c3-c11  
c12  
Performance Monitor  
Control  
Read/write  
0x41141800  
1
2
3
4
5
Count Enable Set  
Read/write  
Read/write  
Read/write  
Write-only  
Read/write  
Unpredictable  
Unpredictable  
Unpredictable  
-
Count Enable Clear  
Overflow Flag Status  
Software Increment  
c9  
0
c12  
c13  
Performance Counter  
Selection  
Unpredictable  
6-7  
0
Undefined  
-
-
-
Cycle Count  
Event Select  
Read/write  
Read/write  
Read/write  
0x00000000  
Unpredictable  
0x00000000  
1
2
Performance Monitor  
Count  
3-7  
Undefined  
-
-
-
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-12  
System Control Coprocessor  
Table 4-2 Summary of CP15 registers and operations (continued)  
CRn  
Op1 CRm  
Op2  
Register or operation  
Type  
Reset value  
Page  
c14  
0
User Enable  
Read/write  
Read/write  
Read/write  
-
0x00000000  
Unpredictable  
Unpredictable  
-
-
1
Interrupt Enable Set  
Interrupt Enable Clear  
Undefined  
c14  
c15  
2
3-7  
0-7  
0-7  
0
c10  
c11  
0
0
c0-c15  
c0  
Undefined  
-
-
-
Slave Port Control  
Undefined  
Read/write  
-
0x00000000  
-
c0  
1-7  
0-7  
0-7  
0
-
c1-c15  
c0-c15  
c0  
c12  
c13  
0
0
FCSE PID  
Context ID  
RAZ,ignore  
writes  
0x00000000  
1
2
Read/write  
Read/write  
0x00000000  
0x00000000  
User read/write  
Thread and Process ID  
0x00000000  
0x00000000  
3
4
User Read-only  
Thread and Process ID  
Read/write  
Read/write  
Privileged Only  
Thread and Process ID  
5-7  
0-7  
0-7  
0
Undefined  
Undefined  
-
-
-
-
-
-
c13  
c14  
c15  
0
0
0
c1-c15  
c0-c15  
c0  
d
Secondary Auxiliary  
Control  
Read/write  
-
1-7  
0
Undefined  
-
-
-
c1  
nVAL IRQ Enable Set  
nVAL FIQ Enable Set  
nVAL Reset Enable Set  
Read/write  
Read/write  
Read/write  
Read/write  
Unpredictable  
Unpredictable  
Unpredictable  
Unpredictable  
1
2
3
nVAL Debug Request  
Enable Set  
4
5
6
7
nVAL IRQ Enable Clear  
nVAL FIQ Enable Clear  
nVAL Reset Enable Clear  
Read/write  
Read/write  
Read/write  
Read/write  
Unpredictable  
Unpredictable  
Unpredictable  
Unpredictable  
c1  
c2  
nVAL Debug Request  
Enable Clear  
d
0
Build Options 1  
Read-only  
-
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-13  
System Control Coprocessor  
Table 4-2 Summary of CP15 registers and operations (continued)  
CRn  
Op1 CRm  
Op2  
Register or operation  
Build Options 2  
Undefined  
Type  
Reset value  
Page  
d
1
Read-only  
-
-
2-7  
0
-
-
c3  
Correctable Fault Location Read/write  
Unpredictable  
-
-
1-7  
0-7  
0
Undefined  
-
c4  
c5  
Invalidate all data cache  
Undefined  
Write-only  
-
-
-
-
1-7  
0-7  
0
c6-c13  
c15  
0
c14  
Cache Size Override  
Undefined  
Write-only  
-
-
-
-
1-7  
0-7  
c15  
a. The value of bits [23:20,3:0] of the Main ID Register depend on product revision. See the register description for more  
information.  
b. Reset value depends on number of MPU regions.  
c. Reset value depends on the cache size implemented.  
d. See register description for more information.  
4.2.2  
c0, Main ID Register  
The Main ID Register returns the device ID code that contains information about the processor.  
The Main ID Register is:  
a read-only register  
accessible in Privileged mode only.  
Figure 4-7 shows the arrangement of bits in the register.  
31  
24 23  
20 19  
16 15  
4
3
0
Implementor  
Variant Architecture  
Primary part number  
Revision  
Figure 4-7 Main ID Register format  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-14  
       
System Control Coprocessor  
The contents of the Main ID Register depend on the specific implementation. Table 4-3 shows  
how the bit values correspond with the Main ID Register functions.  
Table 4-3 Main ID Register bit functions  
Bits  
Field  
Function  
[31:24] Implementer  
Indicates implementer.  
0x41- ARM Limited.  
[23:20] Variant  
Identifies the major revision of the processor. This is the major revision number n in  
the rn part of the rnpn description of the product revision status. See Product revision  
information on page 1-24 for details of the value of this field.  
[19:16] Architecture  
Indicates the architecture version.  
0xF- see feature registers.  
[15:4]  
[3:0]  
Primary part number Indicates processor part number.  
0xC14- Cortex-R4.  
Revision  
Identifies the minor revision of the processor. This is the minor revision number n in  
the pn part of the rnpn description of the product revision status. See Product revision  
information on page 1-24 for details of the value of this field.  
Note  
If an MRCinstruction is executed with CRn = c0, Opcode_1 = 0, CRm = c0, and an Opcode_2  
value corresponding to an unimplemented or reserved ID register, the system control  
coprocessor returns the value of the main ID register.  
To access the Main ID Register, read CP15 with:  
MRC p15, 0, <Rd>, c0, c0, 0 ; Read Main ID Register  
For more information on the processor features, see The Processor Feature Registers on  
4.2.3  
c0, Cache Type Register  
The Cache Type Register determines the instruction and data minimum line length in bytes to  
enable a range of addresses to be invalidated.  
The Cache Type Register is:  
a read-only register  
accessible in Privileged mode only.  
The contents of the Cache Type Register depend on the specific implementation. Figure 4-8  
shows the arrangement of bits in the register.  
31  
28 27  
24 23  
20 19  
16 15 14 13  
4
3
0
Reserved  
CWG  
ERG  
DMinLine  
1
1
Reserved  
IMinLine  
Figure 4-8 Cache Type Register format  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-15  
         
System Control Coprocessor  
Table 4-4 shows how the bit values correspond with the Cache Type Register functions.  
Table 4-4 Cache Type Register bit functions  
Bits  
Field  
Function  
[31:28]  
-
Always b1000.  
[27:24] CWG  
[23:20] ERG  
Cache Write-back Granule  
0x0= no information provided. See maximum cache line size in c0, Current Cache Size  
Exclusives Reservation Granule  
0x0= no information provided.  
[19:16] DMinLine Indicates log2 of the number of words in the smallest cache line of the data and unified caches  
controlled by the processor:  
0x3= eight words in an L1 data cache line.  
[15:14]  
[13: 4]  
[3: 0]  
-
Always 0x3  
.
-
Always 0x000  
.
IMinLine  
Indicates log2 of the number of words in the smallest cache line of the instruction caches  
controlled by the processor:  
0x3- eight words in an L1 instruction cache line.  
To access the Cache Type Register, read CP15 with:  
MRC p15, 0, <Rd>, c0, c0, 1 ; Returns cache details  
4.2.4  
c0, TCM Type Register  
The TCM Type Register informs the processor of the number of ATCMs and BTCMs in the  
system.  
The TCM Type Register is:  
a read-only register  
accessible in Privileged mode only.  
Figure 4-9 shows the arrangement of bits in the register.  
31 30 29 28  
19 18  
16 15  
3
2
0
0
0
0
Reserved  
BTCM  
Reserved  
ATCM  
Figure 4-9 TCM Type Register format  
Table 4-5 shows how the bit values correspond with the TCM Type Register functions.  
Table 4-5 TCM Type Register bit functions  
Bits  
Field  
Function  
[31:29]  
[28:19]  
-
Always 0.  
Reserved SBZ.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-16  
             
System Control Coprocessor  
Table 4-5 TCM Type Register bit functions (continued)  
Bits  
Field  
Function  
[18:16]  
BTCM  
Specifies the number of BTCMs implemented. This is always set to b001because the processor  
has one BTCM.  
[15:3]  
[2:0]  
Reserved SBZ.  
ATCM Specifies the number of ATCMs implemented. Always set to b001. The processor has one ATCM.  
To access the TCM Type Register, read CP15 with:  
MRC p15, 0, <Rd>, c0, c0, 2 ; Returns TCM type register  
Note  
The ATCM and BTCM fields in the TCM Type Register occupy the same space as the  
ITCM and DTCM fields as defined by the ARM Architecture. These fields, and the  
corresponding TCM interfaces, can be considered equivalent to those defined in the  
Architecture.  
The ARM Architecture requires only the ITCM to be accessible from both instruction and  
data sides. In the Cortex-R4 processor, both ATCM and BTCM are accessible from both  
instruction and data sides.  
4.2.5  
c0, MPU Type Register  
The MPU Type Register holds the value for the number of instruction and data memory regions  
implemented in the processor.  
The MPU Type Register is:  
read-only register  
accessible in Privileged mode only.  
Figure 4-10 shows the arrangement of bits in the register.  
31  
16  
8
7
1
0
Reserved  
DRegion  
Reserved  
S
Figure 4-10 MPU Type Register format  
Table 4-6 shows how the bit values correspond with the MPU Type Register functions.  
Table 4-6 MPU Type Register bit functions  
Bits  
Field  
Function  
[31:16] Reserved  
SBZ.  
[15:8]  
[7:1]  
[0]  
DRegion  
Reserved  
S
Specifies the number of unified MPU regions. Set to 0, 8 or 12 data MPU regions.  
SBZ.  
Specifies the type of MPU regions, unified or separate, in the processor.  
Always set to 0, the processor has unified memory regions.  
To access the MPU Type Register, read CP15 with:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-17  
         
System Control Coprocessor  
MRC p15, 0, <Rd>, c0, c0, 4 ; Returns MPU details  
4.2.6  
c0, Multiprocessor ID Register  
The Multiprocessor ID Register enables cores to be recognized and characterized within a  
multiprocessor system.  
The Multiprocessor ID Register is:  
read-only register  
accessible in Privileged mode only.  
Figure 4-11 shows the arrangement of bits in the register.  
31  
24 23  
16  
8
7
0
Reserved  
Affinity Level 2  
Affinity Level 1  
Affinity Level 0  
Figure 4-11 Multiprocessor ID Register format  
Because this is a uniprocessor system, this register is Read-As-Zero.  
To access the Multiprocessor ID Register, read CP15 with:  
MRC p15, 0, <Rd>, c0, c0, 5 ; Returns Multiprocessor ID details  
4.2.7  
The Processor Feature Registers  
There are two Processor Feature Registers, PFR0 and PFR1. This section describes:  
c0, Processor Feature Register 0, PFR0  
The Processor Feature Register 0 provides information about the execution state support and  
programmer’s model for the processor.  
Processor Feature Register 0 is:  
a read-only register  
accessible in Privileged mode only.  
Figure 4-12 shows the bit arrangement for Processor Feature Register 0.  
31  
16 15  
12 11  
8
7
4
3
0
Reserved  
State3  
State2  
State1  
State0  
Figure 4-12 Processor Feature Register 0 format  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-18  
             
System Control Coprocessor  
Table 4-7 shows how the bit values correspond with the Processor Feature Register 0 functions.  
Table 4-7 Processor Feature Register 0 bit functions  
Bits  
[31:16] Reserved SBZ.  
[15:12] State3 Indicates support for Thumb Execution Environment (ThumbEE).  
Field  
Function  
0x0, no support.  
[11:8]  
[7:4]  
[3:0]  
State2  
State1  
State0  
Indicates support for acceleration of execution environments in hardware or software.  
0x1, the processor supports acceleration of execution environments in software.  
Indicates type of Thumb encoding that the processor supports.  
0x3, the processor supports Thumb encoding with all Thumb instructions.  
Indicates support for ARM instruction set.  
0x1, the processor supports ARM instructions.  
To access the Processor Feature Register 0 read CP15 with:  
MRC p15, 0, <Rd>, c0, c1, 0 ; Read Processor Feature Register 0  
c0, Processor Feature Register 1, PFR1  
The Processor Feature Register 1 provides information about the execution state support and  
programmer’s model for the processor.  
Processor Feature Register 1 is:  
a read-only register  
accessible in Privileged mode only.  
Figure 4-13 shows the bit arrangement for Processor Feature Register 1.  
31  
12 11  
8
7
4
3
0
Reserved  
Microcontroller programmer’s model  
Security extension  
ARMv4 Programmer’s model  
Figure 4-13 Processor Feature Register 1 format  
Table 4-8 shows how the bit values correspond with the Processor Feature Register 1 functions.  
Table 4-8 Processor Feature Register 1 bit functions  
Bits  
Field  
Function  
[31:12] Reserved  
SBZ.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-19  
             
System Control Coprocessor  
Table 4-8 Processor Feature Register 1 bit functions (continued)  
Function  
Bits  
Field  
[11:8]  
Microcontroller programmer’s model Indicates support for Microcontroller programmer’s model:  
0x0, no support.  
[7:4]  
[3:0]  
Security extension  
Indicates support for Security Extensions Architecture:  
0x0, no support.  
ARMv4 Programmer’s model  
Indicates support for standard ARMv4 programmer’s model:  
0x1, the processor supports the ARMv4 model.  
To access the Processor Feature Register 1 read CP15 with:  
MRC p15, 0, <Rd>, c0, c1, 1 ; Read Processor Feature Register 1  
4.2.8  
c0, Debug Feature Register 0  
The Debug Feature Register 0 provides information about the debug system for the processor.  
Debug Feature Register 0 is:  
a read-only register  
accessible in Privileged mode only.  
Figure 4-14 shows the bit arrangement for Debug Feature Register 0.  
31  
24 23  
20 19  
16 15  
12 11  
8
7
4
3
0
Reserved  
Microcontroller debug model – memory mapped  
Trace debug model – memory mapped  
Trace debug model – coprocessor  
Core debug model – memory mapped  
Secure debug model  
Core debug model – coprocessor  
Figure 4-14 Debug Feature Register 0 format  
Table 4-9 shows how the bit values correspond with the Debug Feature Register 0 functions.  
Table 4-9 Debug Feature Register 0 bit functions  
Bits  
Field  
Function  
[31:24] Reserved  
SBZ.  
[23:20] Microcontroller  
Debug model -  
Indicates support for the microcontroller debug model - memory mapped:  
0x0, no support.  
memory mapped  
[19:16] Trace debug model -  
memory mapped  
Indicates support for the trace debug model - memory mapped:  
0x1, trace supported, memory mapped access.  
[15:12] Trace debug model -  
coprocessor  
Indicates support for the trace debug model - coprocessor:  
0x0, no support.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-20  
         
System Control Coprocessor  
Table 4-9 Debug Feature Register 0 bit functions (continued)  
Bits  
Field  
Function  
[11:8]  
Core debug model -  
memory mapped  
Indicates the type of embedded processor debug model that the processor supports:  
0x4, ARMv7 based model - memory mapped.  
[7:4]  
[3:0]  
Secure debug model  
Indicates the type of secure debug model that the processor supports:  
0x0, no support.  
Core debug model -  
coprocessor  
Indicates the type of applications processor debug model that the processor supports:  
0x0, no support.  
To access the Debug Feature Register 0 read CP15 with:  
MRC p15, 0, <Rd>, c0, c1, 2 ; Read Debug Feature Register 0  
4.2.9  
c0, Auxiliary Feature Register 0  
The Auxiliary Feature Register 0 provides additional information about the features of the  
processor.  
The Auxiliary Feature Register 0 is:  
a read-only register  
accessible in Privileged mode only.  
In this processor, the Auxiliary Feature Register 0 reads as 0x00000000  
.
To access the Auxiliary Feature Register 0 read CP15 with:  
MRC p15, 0, <Rd>, c0, c1, 3 ; Read Auxiliary Feature Register 0.  
4.2.10 Memory Model Feature Registers  
There are four Memory Model Feature Registers, MMFR0 to MMFR3. They are described in  
the following subsections:  
c0, Memory Model Feature Register 0, MMFR0  
The Memory Model Feature Register 0 provides information about the memory model, memory  
management, and cache support operations of the processor.  
The Memory Model Feature Register 0 is:  
a read-only register  
accessible in Privileged mode only.  
Figure 4-15 on page 4-22 shows the bit arrangement for Memory Model Feature Register 0.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-21  
     
System Control Coprocessor  
31  
28 27  
24 23  
20 19  
16 15  
12 11  
8
7
4
3
0
Reserved  
FCSE  
TCM  
PMSA  
VMSA  
Auxiliary Control Register  
Outer shareable  
Cache coherence  
Figure 4-15 Memory Model Feature Register 0 format  
Table 4-10 shows how the bit values correspond with the Memory Model Feature Register 0  
functions.  
Table 4-10 Memory Model Feature Register 0 bit functions  
Function  
Bits  
Field  
[31:28] Reserved  
[27:24] FCSE  
SBZ.  
Indicates support for Fast Context Switch Extension (FCSE).  
0x0, no support.  
[23:20] Auxiliary Control Register Indicates support for the auxiliary registers.  
0x2, the processor supports the Auxiliary Instruction and Data Fault Status  
Registers (AIFSR and ADFSR) and the Auxiliary Control Register.  
[19:16] TCM  
Indicates support for TCM and associated DMA.  
0x1, implementation defined.  
[15:12] Outer shareable  
Indicates support for the Outer shareable attribute.  
0x0, no support.  
[11:8]  
[7:4]  
[3:0]  
Cache coherence  
PMSA  
Indicates support for cache coherency maintenance.  
0x0, no support for shared caches.  
Indicates support for Physical Memory System Architecture (PMSA).  
0x3, the processor supports PMSAv7 (subsection support).  
VMSA  
Indicates support for Virtual Memory System Architecture (VMSA).  
0x0, no support.  
To access the Memory Model Feature Register 0 read CP15 with:  
MRC p15, 0, <Rd>, c0, c1, 4 ; Read Memory Model Feature Register 0.  
c0, Memory Model Feature Register 1, MMFR1  
The Memory Model Feature Register 1 provides information about the memory model, memory  
management, and cache support of the processor.  
The Memory Model Feature Register 1 is:  
a read-only register  
accessible in Privileged mode only.  
Figure 4-16 on page 4-23 shows the bit arrangement for Memory Model Feature Register 1.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-22  
         
System Control Coprocessor  
31  
28 27  
24 23  
20 19  
16 15  
12 11  
8
7
4
3
0
Branch predictor  
L1 test clean operations  
L1 cache maintenance operations (unified)  
L1 cache maintenance operations (Harvard)  
L1 cache line maintenance operations - Set and Way (unified)  
L1 cache line maintenance operations - Set and Way (Harvard)  
L1 cache line maintenance operations - MVA (unified)  
L1 cache line maintenance operations - MVA (Harvard)  
Figure 4-16 Memory Model Feature Register 1 format  
Table 4-11 shows how the bit values correspond with the Memory Model Feature Register 1  
functions.  
Table 4-11 Memory Model Feature Register 1 bit functions  
Function  
Bits  
Field  
[31:28] Branch predictor  
Indicates Branch Predictor management requirements.  
0x0, no MMU present.  
[27:24] L1 test clean operations  
Indicates support for test and clean operations on data cache, Harvard or unified  
architecture.  
0x0, no support.  
[23:20] L1 cache maintenance  
operations (unified)  
Indicates support for L1 cache, entire cache maintenance operations, unified  
architecture.  
0x0, no support.  
[19:16] L1 cache maintenance  
operations (Harvard)  
Indicates support for L1 cache, entire cache maintenance operations, Harvard  
architecture.  
0x0, no support.  
[15:12] L1 cache line maintenance  
operations - Set and Way  
(unified)  
Indicates support for L1 cache line maintenance operations by Set and Way,  
unified architecture.  
0x0, no support.  
[11:8]  
[7:4]  
[3:0]  
L1 cache line maintenance  
operations - Set and Way  
(Harvard)  
Indicates support for L1 cache line maintenance operations by Set and Way,  
Harvard architecture.  
0x0, no support.  
L1 cache line maintenance  
operations - MVA (unified)  
Indicates support for L1 cache line maintenance operations by address, unified  
architecture.  
0x0, no support.  
L1 cache line maintenance  
operations - MVA (Harvard)  
Indicates support for L1 cache line maintenance operations by address, Harvard  
architecture.  
0x0, no support.  
To access the Memory Model Feature Register 1 read CP15 with:  
MRC p15, 0, <Rd>, c0, c1, 5 ; Read Memory Model Feature Register 1.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-23  
       
System Control Coprocessor  
c0, Memory Model Feature Register 2, MMFR2  
The Memory Model Feature Register 2 provides information about the memory model, memory  
management, and cache support operations of the processor.  
The Memory Model Feature Register 2 is:  
a read-only register  
accessible in Privileged mode only.  
Figure 4-17 shows the bit arrangement for Memory Model Feature Register 2.  
31  
28 27  
24 23  
20 19  
16 15  
12 11  
8
7
4
3
0
Hardware  
access flag  
Memory  
barrier  
WFI  
TLB maintenance operations (unified)  
TLB maintenance operations (Harward)  
L1 cache maintenance range operations (Harward)  
L1 background prefetch cache operations  
L1 foreground prefetch cache operations  
Figure 4-17 Memory Model Feature Register 2 format  
Table 4-12 shows how the bit values correspond with the Memory Model Feature Register 2  
functions.  
Table 4-12 Memory Model Feature Register 2 bit functions  
Function  
Bits  
Field  
[31:28] Hardware access flag Indicates support for Hardware Access Flag.  
0x0, no support.  
[27:24] WFI  
Indicates support for Wait-For-Interrupt stalling.  
0x1, the processor supports Wait-For-Interrupt.  
[23:20] Memory barrier  
Indicates support for memory barrier operations.  
0x2, the processor supports:  
DSB (formerly DWB)  
ISB (formerly Prefetch Flush)  
DMB.  
[19:16] TLB maintenance  
operations (unified)  
Indicates support for TLB maintenance operations, unified architecture.  
0x0, no support.  
[15:12] TLB maintenance  
operations (Harvard)  
Indicates support for TLB maintenance operations, Harvard architecture.  
0x0, no support.  
[11:8]  
L1 cache  
Indicates support for cache maintenance range operations, Harvard architecture.  
maintenance range  
operations (Harvard)  
0x0, no support.  
[7:4]  
L1 background  
prefetch cache  
operations  
Indicates support for background prefetch cache range operations, Harvard  
architecture.  
0x0, no support.  
[3:0]  
L1 foreground  
prefetch cache  
operations  
Indicates support for foreground prefetch cache range operations, Harvard  
architecture.  
0x0, no support.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-24  
         
System Control Coprocessor  
To access the Memory Model Feature Register 2 read CP15 with:  
MRC p15, 0, <Rd>, c0, c1, 6 ; Read Memory Model Feature Register 2.  
c0, Memory Model Feature Register 3, MMFR3  
The Memory Model Feature Register 3 provides information about the two cache line  
maintenance operations for the processor.  
The Memory Model Feature Register 3 is:  
a read-only register  
accessible in Privileged mode only.  
Figure 4-18 shows the bit arrangement for Memory Model Feature Register 3.  
31  
12 11  
8
7
4
3
0
Reserved  
Branch predictor maintenance operations  
Hierarchical cache maintenance operations by Set and Way  
Hierarchical cache maintenance operations by MVA  
Figure 4-18 Memory Model Feature Register 3 format  
Table 4-13 shows how the bit values correspond with the Memory Model Feature Register 3  
functions.  
Table 4-13 Memory Model Feature Register 3 bit functions  
Function  
Bits  
Field  
[31:12] Reserved  
SBZ.  
[11:8]  
[7:4]  
Branch predictor maintenance  
operations  
Indicates support for branch predictor maintenance operations in systems  
with hierarchical cache maintenance operations.  
0x0, no support.  
Hierarchical cache maintenance  
operations by Set and Way  
Indicates support for hierarchical cache maintenance operations by Set and  
Way.  
0x1, the processor supports invalidate cache, clean and invalidate, and clean  
by Set and Way.  
[3:0]  
Hierarchical cache maintenance  
operations by MVA  
Indicates support for hierarchical cache maintenance operations by address.  
0x1, the processor supports:  
Invalidate data cache by address  
Clean data cache by address  
Clean and invalidate data cache by address  
Invalidate instruction cache by address  
Invalidate all instruction cache entries.  
To access the Memory Model Feature Register 3 read CP15 with:  
MRC p15, 0, <Rd>, c0, c1, 7 ; Read Memory Model Feature Register 3.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-25  
         
System Control Coprocessor  
4.2.11 Instruction Set Attributes Registers  
There are eight Instruction Set Attributes Registers, ISAR0 to ISAR7, but three of these are  
currently unused. This section describes:  
c0, Instruction Set Attributes Register 0, ISAR0  
The Instruction Set Attributes Register 0 provides information about the instruction set that the  
processor supports beyond the basic set.  
The Instruction Set Attributes Register 0 is:  
a read-only register  
accessible in Privileged mode only.  
Figure 4-19 shows the bit arrangement for Instruction Set Attributes Register 0.  
31  
28 27  
24 23  
20 19  
16 15  
12 11  
8
7
4
3
0
Reserved  
Divide instructions  
Debug instructions  
Coprocessor instructions  
Compare and branch instructions  
Bitfield instructions  
Bit count instructions  
Atomic instructions  
Figure 4-19 Instruction Set Attributes Register 0 format  
Table 4-14 shows how the bit values correspond with the Instruction Set Attributes Register 0  
functions.  
Table 4-14 Instruction Set Attributes Register 0 bit functions  
Bits  
Field  
Function  
[31:28] Reserved  
SBZ  
[27:24] Divide instructions  
Indicates support for divide instructions.  
0x1, the processor supports SDIVand UDIVinstructions.  
[23:20] Debug instructions  
Indicates support for debug instructions.  
0x1, the processor supports BKPT  
.
[19:16] Coprocessor instructions Indicates support for coprocessor instructions other than separately attributed  
feature registers, such as CP15 registers and VFP.  
0x0, no support.  
[15:12] Compare and branch  
instructions  
Indicates support for combined compare and branch instructions.  
0x1, the processor supports combined compare and branch instructions, CBNZand  
CBZ  
.
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-26  
           
System Control Coprocessor  
Table 4-14 Instruction Set Attributes Register 0 bit functions (continued)  
Bits  
Field  
Function  
[11:8]  
Bitfield instructions  
Indicates support for bitfield instructions.  
0x1, the processor supports bitfield instructions, BFC BFI, SBFX, and UBFX.  
,
[7:4]  
[3:0]  
Bit counting instructions Indicates support for bit counting instructions.  
0x1, the processor supports CLZ  
.
Atomic instructions  
Indicates support for atomic load and store instructions.  
0x1, the processor supports SWPand SWPB  
.
To access the Instruction Set Attributes Register 0, read CP15 with:  
MRC p15, 0, <Rd>, c0, c2, 0 ; Read Instruction Set Attributes Register 0  
c0, Instruction Set Attributes Register 1, ISAR1  
The Instruction Set Attributes Register 1 provides information about the instruction set that the  
processor supports beyond the basic set.  
The Instruction Set Attributes Register 1 is:  
a read-only register  
accessible in Privileged mode only.  
Figure 4-20 shows the bit arrangement for Instruction Set Attributes Register 1.  
31  
28 27  
24 23  
20 19  
16 15  
12 11  
8
7
4
3
0
Jazelle instructions  
Interworking instructions  
Immediate instructions  
ITE instructions  
Extend instructions  
Exception 2 instructions  
Exception 1 instructions  
Endian instructions  
Figure 4-20 Instruction Set Attributes Register 1 format  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-27  
     
System Control Coprocessor  
Table 4-15 shows how the bit values correspond with the Instruction Set Attributes Register 1  
functions.  
Table 4-15 Instruction Set Attributes Register 1 bit functions  
Bits  
Field  
Function  
[31:28] Jazelle  
Indicates support for Jazelle instructions.  
instructions  
0x1, the processor supports:  
BXJinstruction  
J bit in PSRs.  
[27:24] Interworking  
instructions  
Indicates support for interworking instructions.  
0x3, the processor supports:  
BX, and T bit in PSRs  
BLX, and PC loads have BX behavior.  
Data-processing instructions in the ARM instruction set with the PC as the destination  
and the S bit clear have BX-like behavior.  
[23:20] Immediate  
instructions  
Indicates support for immediate instructions.  
0x1, the processor supports:  
the MOVT instruction  
MOV instruction encodings with 16-bit immediates  
Thumb ADD and SUB instructions with 12-bit immediates.  
[19:16] ITE  
instructions  
Indicates support for if then instructions.  
0x1, the processor supports ITinstructions.  
[15:12] Extend  
instructions  
Indicates support for sign or zero extend instructions.  
0x2, the processor supports:  
SXTB  
,
SXTB16  
,
SXTH  
,
UXTB  
,
UXTB16, and UXTH  
UXTAB16, and UXTAH.  
SXTAB  
,
SXTAB16  
,
SXTAH  
,
UXTAB  
,
[11:8]  
[7:4]  
Exception 2  
instructions  
Indicates support for exception 2 instructions.  
0x1, the processor supports RFE  
,
SRS, and CPS.  
Exception 1  
instructions  
Indicates support for exception 1 instructions.  
0x1, the processor supports LDM(exception return), LDM(user registers), and STM(user  
registers).  
[3:0]  
Endian  
Indicates support for endianness control instructions.  
instructions  
0x1, the processor supports SETENDand E bit in PSRs.  
To access the Instruction Set Attributes Register 1 read CP15 with:  
MRC p15, 0, <Rd>, c0, c2, 1 ; Read Instruction Set Attributes Register 1  
c0, Instruction Set Attributes Register 2, ISAR2  
The Instruction Set Attributes Register 2 provides information about the instruction set that the  
processor supports beyond the basic set.  
The Instruction Set Attributes Register 2 is:  
a read-only register  
accessible in Privileged mode only.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-28  
     
System Control Coprocessor  
Figure 4-21 shows the bit arrangement for Instruction Set Attributes Register 2.  
31  
28 27  
24 23  
20 19  
16 15  
12 11  
8
7
4
3
0
Reversal instructions  
PSR instructions  
Unsigned multiply instructions  
Signed multiply instructions  
Multiply instructions  
Interruptible instructions  
Memory hint instructions  
Load/store instructions  
Figure 4-21 Instruction Set Attributes Register 2 format  
Table 4-16 shows how the bit values correspond with the Instruction Set Attributes Register 2  
functions.  
Table 4-16 Instruction Set Attributes Register 2 bit functions  
Function  
Bits  
Field  
[31:28] Reversal  
instructions  
Indicates support for reversal instructions.  
0x2, the processor supports REV REV16, REVSH, and RBIT.  
,
[27:24] PSR  
instructions  
Indicates support for PSRinstructions.  
0x1, the processor supports MRSand MSR, and the exception return forms of data-processing  
instructions.  
[23:20] Unsigned  
multiply  
Indicates support for advanced unsigned multiply instructions.  
0x2, the processor supports:  
instructions  
UMULLand UMLAL  
UMAAL  
.
[19:16] Signed  
multiply  
Indicates support for advanced signed multiply instructions.  
0x3, the processor supports:  
instructions  
SMULLand SMLAL  
SMLABB  
,
,
SMLABT  
,
,
SMLALBB  
,
SMLALBT  
,
SMLALTB  
SMULWB  
SMLSD  
,
SMLALTT  
,
SMLATB  
,
SMLATT  
,
SMLAWB  
,
SMLAWT  
,
SMULBB  
SMULBT  
SMULTB  
,
SMULTT  
SMLALDX  
SMUAD  
,
,
SMULWT, and Q flag in PSRs  
SMLAD  
,
SMLADX  
,
,
SMLALD  
,
,
,
,
SMLSDX  
,
SMLSLD  
,
SMLSLDX  
,
SMMLA  
,
SMMLAR  
,
SMMLS  
,
SMMLSR  
,
SMPUL  
SMPULR  
,
SMUADX  
,
SMUSD, and SMUSDX.  
[15:12] Multiply  
instructions  
Indicates support for multiply instructions.  
0x2, the processor supports MUL  
,
MLA, and MLS.  
[11:8]  
[7:4]  
[3:0]  
Interruptible  
instructions  
Indicates support for multi-access interruptible instructions.  
0x1, the processor supports restartable LDMand STM  
.
Memory hint  
instructions  
Indicates support for memory hint instructions.  
0x3, the processor supports PLDand PLI  
.
Load/store  
instructions  
Indicates support for additional load and store instructions.  
0x1, the processor supports LDRDand STRD  
.
To access the Instruction Set Attributes Register 2 read CP15 with:  
MRC p15, 0, <Rd>, c0, c2, 2 ; Read Instruction Set Attributes Register 2  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-29  
       
System Control Coprocessor  
c0, Instruction Set Attributes Register 3, ISAR3  
The Instruction Set Attributes Register 3 provides information about the instruction set that the  
processor supports beyond the basic set.  
The Instruction Set Attributes Register 3 is:  
a read-only registers  
accessible in Privileged mode only.  
Figure 4-22 shows the bit arrangement for Instruction Set Attributes Register 3.  
31  
28 27  
24 23  
20 19  
16 15  
12 11  
8
7
4
3
0
ThumbEE extension  
True NOP instructions  
Thumb copy instructions  
Table branch instructions  
Synchronization primitive instructions  
SVC instructions  
SIMD instructions  
Saturate instructions  
Figure 4-22 Instruction Set Attributes Register 3 format  
Table 4-17 shows how the bit values correspond with the Instruction Set Attributes Register 3  
functions.  
Table 4-17 Instruction Set Attributes Register 3 bit functions  
Function  
Bits  
Field  
[31:28] ThumbEE  
extension  
Indicates support for ThumbEE Execution Environment extension.  
0x0, no support.  
[27:24] True NOP  
instructions  
Indicates support for true NOPinstructions.  
0x1, the processor supports NOP16 NOP32and various NOPcompatible hints in both the ARM  
,
and Thumb instruction sets.  
[23:20] Thumb copy  
instructions  
Indicates support for Thumb copy instructions.  
0x1, the processor supports Thumb MOV(3)low register low register.  
[19:16] Table branch  
instructions  
Indicates support for table branch instructions.  
0x1, the processor supports table branch instructions, TBBand TBH  
.
[15:12] Synchronization  
primitive  
Indicates support for synchronization primitive instructions.  
0x2, the processor supports:  
instructions  
LDREXand STREX  
LDREXB LDREXH LDREXD STREXB, STREXH, STREXD, and CLREX.  
,
,
,
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-30  
           
System Control Coprocessor  
Table 4-17 Instruction Set Attributes Register 3 bit functions (continued)  
Bits  
Field  
Function  
[11:8]  
SVC instructions  
Indicates support for SVC(formerly SWI) instructions.  
0x1, the processor supports SVC  
.
[7:4]  
SIMD  
Indicates support for Single Instruction Multiple Data (SIMD) instructions.  
instructions  
0x3, the processor supports:  
PKHBT  
,
PKHTB  
,
QADD16  
,
QADD8  
SHSUB16 SHSUB8  
UASX UHADD16 UHADD8  
UQSAX USAD8 USADA8  
,
QASX  
,
QSUB16  
,
QSUB8  
SSAT SSAT16  
UHSUB16  
USAT16  
,
QSAX  
,
SADD16  
,
SADD8  
SSUB8 SSAX  
USAX UQADD16  
USUB8 USAX UXTAB16  
,
SASX  
SXTAB16  
UQADD8  
,
SEL  
,
SHADD16  
SXTB16  
UQASX  
UXTB16  
,
SHADD8  
,
,
SHASX  
,
,
,
,
SHSAX  
,
,
,
,
,
SSUB16  
UHSUB8  
USUB16  
,
,
,
,
,
,
,
,
,
UADD16  
UADD8  
,
,
,
UASX  
,
,
,
,
UQSUB16  
,
UQSUB8  
,
,
,
,
USAT  
,
,
,
,
and the GE[3:0] bits in the PSRs.  
Indicates support for saturate instructions.  
0x1, the processor supports QADD QDADD, QDSUB, QSUBand Q flag in PSRs.  
[3:0]  
Saturate  
instructions  
,
To access the Instruction Set Attributes Register 3 read CP15 with:  
MRC p15, 0, <Rd>, c0, c2, 3 ; Read Instruction Set Attributes Register 3  
c0, Instruction Set Attributes Register 4, ISAR4  
The Instruction Set Attributes Register 4 provides information about the instruction set that the  
processor supports beyond the basic set.  
The Instruction Set Attributes Register 4 is:  
a read-only register  
accessible in Privileged mode only.  
Figure 4-23 shows the bit arrangement for Instruction Set Attributes Register 4.  
31  
24 23  
20 19  
16 15  
12 11  
8
7
4
3
0
Reserved  
Exclusive instructions  
Barrier instructions  
SMC instructions  
Unprivileged instructions  
With shift instructions  
Write-back instructions  
Figure 4-23 Instruction Set Attributes Register 4 format  
Table 4-18 shows how the bit values correspond with the Instruction Set Attributes Register 4  
functions.  
Table 4-18 Instruction Set Attributes Register 4 bit functions  
Function  
Bits  
Field  
[31:24] Reserved  
SBZ.  
[23:20] Exclusive instructions  
Indicates support for Exclusive instructions.  
0x0, Only supports synchronization primitive instructions as indicated by bits  
[15:12] in the ISAR3 register. See c0, Instruction Set Attributes Register 3, ISAR3  
on page 4-30 for more information.  
[19:16] Barrier instructions  
Indicates support for Barrier instructions.  
0x1, the processor supports DMB DSB, and ISBinstructions.  
,
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-31  
         
System Control Coprocessor  
Table 4-18 Instruction Set Attributes Register 4 bit functions (continued)  
Function  
Bits  
Field  
[15:12] SMC instructions  
Indicates support for Secure Monitor Call (SMC) (formerly SMI) instructions.  
0x0, no support.  
[11:8]  
[7:4]  
Write-back instructions  
Indicates support for write-back instructions.  
0x1, supports all the writeback addressing modes defined in ARMv7.  
With shift instructions  
Indicates support for with-shift instructions.  
0x4, the processor supports:  
the full range of constant shift options, on load/store and other instructions  
register-controlled shift options.  
[3:0]  
Unprivileged instructions Indicates support for Unprivileged instructions.  
0x2, the processor supports LDR{SB|B|SH|H}Tand STR{B|H}T  
.
To access the Instruction Set Attributes Register 4 read CP15 with:  
MRC p15, 0, <Rd>, c0, c2, 4 ; Read Instruction Set Attributes Register 4  
c0, Instruction Set Attributes Registers 5-7  
The Instruction Set Attributes Registers 5-7 provide additional information about the properties  
of the processor.  
The Instruction Set Attributes Register 5 is:  
a read-only register  
accessible in Privileged mode only.  
In the processor, Instruction Set Attributes Register 5 is read as 0x00000000  
.
To access the Instruction Set Attributes Register 5, read CP15 with:  
MRC p15, 0, <Rd>, c0, c2, 5 ; Read Instruction Set Attribute Register 5  
Instruction Set Attributes Registers 6 and 7 are not implemented, and their positions in the  
register map are Reserved. They correspond to CP15 accesses with:  
MRC p15, 0, <Rd>, c0, c2, 6 ; Read Instruction Set Attribute Register 6  
MRC p15, 0, <Rd>, c0, c2, 7 ; Read Instruction Set Attribute Register 7  
These registers are read-only, and are accessible in Privileged mode only.  
4.2.12 c0, Current Cache Size Identification Register  
The Current Cache Size Identification Register provides the current cache size information for  
the instruction and data caches. Architecturally, there can be up to eight levels of cache,  
containing instruction, data, or unified caches. This processor contains L1 instruction and data  
caches. The Cache Size Selection Register determines which Current Cache Size Identification  
The Current Cache Size Identification Register is:  
a read-only register  
accessible in Privileged mode only.  
Figure 4-24 on page 4-33 shows the bit arrangement for the Current Cache Size Identification  
Register.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-32  
   
System Control Coprocessor  
31 30 29 28 27  
W W R W  
13 12  
2
0
Line  
Size  
NumSets  
Associativity  
T
B A A  
Figure 4-24 Current Cache Size Identification Register format  
Table 4-19 shows how the bit values correspond with the Current Cache Size Identification  
Register.  
Table 4-19 Current Cache Size Identification Register bit functions  
Bits  
Field  
Function  
[31]  
WT  
Indicates support available for write-through:  
1 = write-through support availablea  
[30]  
[29]  
[28]  
WB  
RA  
WA  
Indicates support available for write-back:  
1 = write-back support availablea  
Indicates support available for read allocation:  
1 = read allocation support availablea  
Indicates support available for write allocation:  
1 = write allocation support availablea  
[27:13] NumSets  
Indicates the number of sets as  
(number of sets) - 1a  
[12:3]  
[2:0]  
Associativity Indicates the number of ways as  
(number of ways) - 1a  
Indicates the number of words in each cache linea  
LineSize  
a. See Table 4-20 for valid bit field encodings.  
The LineSize field is encoded as 2 less than log(2) of the number of words in the cache line. For  
example, a value of 0x0indicates there are four words in a cache line, that is the minimum size  
for the cache. A value of 0x1indicates there are eight words in a cache line.  
Table 4-20 shows the individual bit field and complete register encodings for the Current Cache  
Size Identification Register. Use this to match the cache size and level of cache set by the  
Current Cache Size Selection Register (CSSR). See c0, Cache Size Selection Register on  
Table 4-20 Bit field and register encodings for Current Cache Size Identification Register  
Register bit field encoding  
Complete  
register  
Size  
encoding  
WT WB RA WA NumSets Associativity LineSize  
4KB  
0xF003E019  
0xF007E019  
0xF00FE019  
0xF01FE019  
0xF03FE019  
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0x001F  
0x003F  
0x007F  
0x00FF  
0x01FF  
0x3  
0x1  
8KB  
16KB  
32KB  
64KB  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-33  
           
System Control Coprocessor  
To access the Current Cache Size Identification Register read CP15 with:  
MRC p15, 1, <Rd>, c0, c0, 0 ; Read Current Cache Size Identification Register  
4.2.13 c0, Current Cache Level ID Register  
The Current Cache Level ID Register indicates the cache levels that are implemented.  
Architecturally, there can be a different number of cache levels on the instruction and data side.  
The register also captures the point-of-coherency and the point-of-unification.  
The Current Cache Level ID Register is:  
a read-only register  
accessible in Privileged mode only.  
Figure 4-25 shows the bit arrangement for the Current Cache Level ID Register.  
31 30 29  
27 26  
24 23  
21 20  
18 17  
15 14  
12 11 10  
CL 4  
8
6
5
3
2
0
LoU  
LoC  
CL 8  
CL 7  
CL 6  
CL 5  
CL 3  
CL 2  
CL 1  
Reserved  
Figure 4-25 Current Cache Level ID Register format  
Table 4-21 shows how the bit values correspond with the Current Cache Level ID Register.  
Table 4-21 Current Cache Level ID Register bit functions  
Bits  
Field  
Function  
[31:30] Reserved SBZ  
[29:27] LoU  
[26:24] LoC  
[23:21] CL 8  
[20:18] CL 7  
[17:15] CL 6  
[14:12] CL 5  
0b001 = Level of Unification  
0b001 = Level of Coherency  
0b000 = no cache at Cache Level (CL) 8  
0b000 = no cache at CL 7  
0b000 = no cache at CL 6  
0b000 = no cache at CL 5  
[11:9]  
[8:6]  
[5:3]  
[2]  
CL 4  
CL 3  
CL 2  
CL 1  
CL 1  
0b000 = no cache at CL 4  
0b000 = no cache at CL 3  
0b000 = no cache at CL 2  
RAZ. Indicates no unified cache at CL1  
[1]  
0b001 if a data cache is implemented  
0b000 if no data cache is implemented  
[0]  
CL 1  
0b001 if an instruction cache is implemented  
0b000 if no instruction cache is implemented  
To access the Current Cache Level ID Register, read CP15 with:  
MRC p15, 1, <Rd>, c0, c0, 1 ; Read Current Cache Level ID Register  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-34  
         
System Control Coprocessor  
4.2.14 c0, Cache Size Selection Register  
The Cache Size Selection Register holds the value that the processor uses to select the Current  
Cache Size Identification Register to use.  
The Cache Size Selection Register is:  
a read/write register  
accessible in Privileged mode only.  
Figure 4-26 shows the bit arrangement for the Cache Size Selection Register.  
31  
4
3
1
0
Reserved  
Level  
InD  
Figure 4-26 Cache Size Selection Register format  
Table 4-22 shows how the bit values correspond with the Cache Size Selection Register.  
Table 4-22 Cache Size Selection Register bit functions  
Bits  
Field  
Function  
[31: 4] Reserved SBZ.  
[3:1]  
[0]  
Level  
InD  
Identifies which cache level to select.  
b000 = Level 1 cache  
This field is read only, writes are ignored.  
Identifies instruction or data cache to use.  
1 = instruction  
0 = data.  
To access the Current Cache Size Identification Registers read or write CP15 with:  
MRC p15, 2, <Rd>, c0, c0, 0 ; Read Cache Size Selection Register  
MCR p15, 2, <Rd>, c0, c0, 0 ; Write Cache Size Selection Register  
4.2.15 c1, System Control Register  
The System Control Register provides control and configuration information for:  
memory alignment, endianness, protection, and fault behavior  
MPU and cache enables and cache replacement strategy  
interrupts and the behavior of interrupt latency  
the location for exception vectors  
program flow prediction.  
The System Control Register is:  
a read/write register  
accessible in Privileged mode only.  
Figure 4-27 on page 4-36 shows the arrangement of bits in the register.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-35  
             
System Control Coprocessor  
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10  
SBO  
7
6
3
2
1
0
1
V
I
SBZ  
SBO  
C A M  
IE  
TE  
Z
AFE  
TRE  
NMFI  
SBZ  
EE  
RR  
SBZ  
SBO  
BR  
SBO  
DZ  
VE  
FI  
SBZ  
Figure 4-27 System Control Register format  
Table 4-23 shows the purposes of the individual bits in the System Control Register.  
Table 4-23 System Control Register bit functions  
Bits  
Field  
Function  
[31]  
IE  
Identifies little or big instruction endianness in use:  
0 = little-endianness  
1 = big-endianness.  
The primary input CFGIE defines the reset value. This bit is read-only.  
[30]  
TE  
Thumb exception enable:  
0 = enable ARM exception generation  
1 = enable Thumb exception generation.  
The primary input TEINIT defines the reset value.  
[29]  
[28]  
[27]  
AFE  
Access Flag Enable. On the processor this bit is SBZ.  
TEX Remap Enable. On the processor this bit is SBZ.  
TRE  
NMFI  
NMFI, non-maskable fast interrupt enable:  
0 = Software can disable FIQs  
1 = Software cannot disable FIQs.  
This bit is read-only. The configuration input CFGNMFI defines its value.  
[26]  
[25]  
Reserved SBZ.  
EE  
Determines how the E bit in the CPSR is set on an exception:  
0 = CPSR E bit is set to 0 on an exception  
1 = CPSR E bit is set to 1 on an exception.  
The primary input CFGEE defines the reset value.  
[24]  
VE  
Configures vectored interrupt:  
0 = offset for IRQ = 0x18  
1 = VIC controller provides offset for IRQ.  
The reset value of this bit is 0.  
[23:22] Reserved SBO.  
[21]  
FI  
Fast Interrupts enable.  
On the processor Fast Interrupts are always enabled. This bit is SBO.  
[20]  
Reserved SBZ.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-36  
       
System Control Coprocessor  
Table 4-23 System Control Register bit functions (continued)  
Bits  
Field  
Function  
[19]  
DZ  
Divide by zero:  
0 = do not generate an Undefined instruction exception  
1 = generate an Undefined instruction exception.  
The reset value of this bit is 0.  
[18]  
[17]  
[16]  
[15]  
[14]  
Reserved SBO.  
BR  
MPU background region enable.  
Reserved SBO.  
Reserved SBZ.  
RR  
Round-robin bit, controls replacement strategy for instruction and data caches:  
0 = random replacement strategy  
1 = round-robin replacement strategy.  
The reset value of this bit is 0. The processor always uses a random replacement strategy,  
regardless of the state of this bit.  
[13]  
[12]  
[11]  
V
I
Determines the location of exception vectors:  
0 = normal exception vectors selected, address range = 0x00000000-0x0000001C  
1 = high exception vectors (HIVECS) selected, address range = 0xFFFF0000-0xFFFF001C  
.
The primary input VINITHI defines the reset value.  
Enables L1 instruction cache:  
0 = instruction caching disabled. This is the reset value.  
1 = instruction caching enabled.  
If no instruction cache is implemented, then this bit is SBZ.  
Z
Branch prediction bit.  
The processor supports branch prediction. This bit is SBO. The Auxiliary Control Register can  
control branch prediction, see Auxiliary Control Registers on page 4-38.  
[10:7]  
[6:3]  
[2]  
Reserved SBZ.  
Reserved SBO.  
C
Enables L1 data cache:  
0 = data caching disabled. This is the reset value.  
1 = data caching enabled.  
If no data cache is implemented, then this bit is SBZ.  
[1]  
[0]  
A
Enables strict alignment of data to detect alignment faults in data accesses:  
0 = strict alignment fault checking disabled. This is the reset value.  
1 = strict alignment fault checking enabled.  
M
Enables the MPU:  
0 = MPU disabled. This is the reset value.  
1 = MPU enabled.  
If no MPU is implemented, the MPU has zero regions, this bit is SBZ.  
To use the System Control Register ARM recommends that you use a read-modify-write  
technique. To access the System Control Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c1, c0, 0 ; Read System Control Register configuration data  
MCR p15, 0, <Rd>, c1, c0, 0 ; Write System Control Register configuration data  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-37  
System Control Coprocessor  
Attempts to read or write the System Control Register from User mode results in an Undefined  
exception.  
4.2.16 Auxiliary Control Registers  
The Auxiliary Control Registers control:  
branch prediction  
performance features  
error and parity logic.  
c1, Auxiliary Control Register  
The Auxiliary Control Register is:  
a read/write register  
accessible in Privileged mode only.  
Figure 4-28 shows the arrangement of bits in the register.  
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9  
BP  
8
7
6
5
3
2
1
0
CEC  
DICDI  
DIB2DI  
DIB1DI  
ATCMECEN  
B0TCMECEN  
B1TCMECEN  
DILS  
DIADI  
B1TCMPCEN  
B0TCMPCEN  
ATCMPCEN  
AXISCEN  
AXISCUEN  
DILSM  
sMOV  
FDSnS  
FWT  
FORA  
DNCH  
ERPEG  
DLFO  
DEOLP  
DBHE  
DBWR  
FRCDIS  
RSDIS  
Reserved  
Figure 4-28 Auxiliary Control Register format  
Table 4-24 shows how the bit values correspond with the Auxiliary Control Register functions.  
Table 4-24 Auxiliary Control Register bit functions  
Function  
Bits  
Field  
DICDIa  
[31]  
Case C dual issue control:  
0 = Enabled. This is the reset value.  
1 = Disabled.  
DIB2DIa  
DIB1DIa  
[30]  
[29]  
Case B2 dual issue control:  
0 = Enabled. This is the reset value.  
1 = Disabled.  
Case B1 dual issue control:  
0 = Enabled. This is the reset value.  
1 = Disabled.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-38  
                 
System Control Coprocessor  
Table 4-24 Auxiliary Control Register bit functions (continued)  
Bits  
Field  
Function  
DIADIa  
[28]  
Case A dual issue control:  
0 = Enabled. This is the reset value.  
1 = Disabled.  
[27]  
[26]  
B1TCMPCEN B1TCM parity or ECC check enable:  
0 = Disabled  
1 = Enabled.  
The primary input PARECCENRAM[2]b defines the reset value.  
If the BTCM is configured with ECC, you must always set this bit to the same value as  
B0TCMPCEN.  
B0TCMPCEN B0TCM parity or ECC check enable:  
0 = Disabled  
1 = Enabled.  
The primary input PARECCENRAM[1]b defines the reset value.  
If the BTCM is configured with ECC, you must always set this bit to the same value as  
B1TCMPCEN.  
[25]  
[24]  
ATCMPCEN  
AXISCEN  
ATCM parity or ECC check enable:  
0 = Disabled  
1 = Enabled.  
The primary input PARECCENRAM[0]b defines the reset value.  
AXI slave cache RAM access enable:  
0 = Disabled. This is the reset value.  
1 = Enabled.  
Note  
When AXI slave cache access is enabled, the caches are disabled and the processor cannot  
run any cache maintenance operations. If the processor attempts a cache maintenance  
operation, an Undefined instruction exception is taken.  
[23]  
[22]  
[21]  
[20]  
[19]  
[18]  
AXISCUEN  
DILSM  
AXI slave cache RAM non-privileged access enable:  
0 = Disabled. This is the reset value.  
1 = Enabled.  
Disable Low Interrupt Latency (LIL) on load/store multiples:  
0 = Enable LIL on load/store multiples. This is the reset value.  
1 = Disable LIL on all load/store multiples.  
DEOLP  
Disable end of loop prediction:  
0 = Enable loop prediction. This is the reset value.  
1 = Disable loop prediction.  
DBHE  
Disable Branch History (BH) extension:  
0 = Enable the extension. This is the reset value.  
1 = Disable the extension.  
FRCDIS  
Reserved  
Fetch rate control disable:  
0 = Normal fetch rate control operation. This is the reset value.  
1 = Fetch rate control disabled.  
SBZ.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-39  
 
System Control Coprocessor  
Table 4-24 Auxiliary Control Register bit functions (continued)  
Bits  
Field  
Function  
[17]  
RSDIS  
Return stack disable:  
0 = Normal return stack operation. This is the reset value.  
1 = Return stack disabled.  
[16:15] BP  
This field controls the branch prediction policy:  
b00 = Normal operation. This is the reset value.  
b01 = Branch always taken.  
b10 = Branch always not taken.  
b11 = Reserved. Behavior is Unpredictable if this field is set to b11.  
[14]  
[13]  
[12]  
DBWR  
Disable write burst in the AXI master:  
0 = Normal operation. This is the reset value.  
1 = Disable write burst optimization.  
DLFO  
Disable linefill optimization in the AXI master:  
0 = Normal operation. This is the reset value.  
1 = Limits the number of outstanding data linefills to two.  
ERPEGc  
Enable random parity error generation:  
0 = Random parity error generation disabled. This is the reset value.  
1 = Enable random parity error generation in the cache RAMs.  
Note  
This bit controls error generation logic during system validation. A synthesized ASIC  
typically does not have such models and this bit is therefore redundant for ASICs.  
[11]  
[10]  
[9]  
DNCH  
FORA  
FWT  
Disable data forwarding for Non-cacheable accesses in the AXI master:  
0 = Normal operation. This is the reset value.  
1 = Disable data forwarding for Non-cacheable accesses.  
Force outer read allocate (ORA) for outer write allocate (OWA) regions:  
0 = No forcing of ORA. This is the reset value.  
1 = ORA forced for OWA regions.  
Force write-through (WT) for write-back (WB) regions:  
0 = No forcing of WT. This is the reset value.  
1 = WT forced for WB regions.  
[8]  
FDSnS  
sMOV  
Force D-side to not-shared when MPU is off:  
0 = Normal operation. This is the reset value.  
1 = D-side normal Non-cacheable forced to Non-shared when MPU is off.  
[7]  
sMOV of a divide does not complete out of order. No other instruction is issued until the  
divide is finished.  
0 = Normal operation. This is the reset value.  
1 = sMOV out of order disabled.  
[6]  
DILS  
CEC  
Disable low interrupt latency on all load/store instructions.  
0 = Enable LIL on all load/store instructions. This is the reset value.  
1 = Disable LIL on all load/store instructions.  
[5:3]  
Cache error control for cache parity and ECC errors.  
See Table 8-2 on page 8-21 and Table 8-3 on page 8-22 for details of how these bits are used.  
The reset value is b100.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-40  
System Control Coprocessor  
Table 4-24 Auxiliary Control Register bit functions (continued)  
Bits  
Field  
Function  
[2]  
B1TCMECEN B1TCM external error enable:  
0 = Disabled  
1 = Enabled.  
The primary input ERRENRAM[2] defines the reset value.  
[1]  
[0]  
B0TCMECEN B0TCM external error enable:  
0 = Disabled  
1 = Enabled.  
The primary input ERRENRAM[1] defines the reset value.  
ATCMECEN  
ATCM external error enable:  
0 = Disabled  
1 = Enabled.  
The primary input ERRENRAM[0] defines the reset value.  
c. This bit is only supported if parity error generation is implemented in your design.  
To access the Auxiliary Control Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c1, c0, 1 ; Read Auxiliary Control Register  
MCR p15, 0, <Rd>, c1, c0, 1 ; Write Auxiliary Control Register  
ARM recommends that any instruction that changes bits [31:28] or [7] is followed by an ISB  
instruction to ensure that the changes have taken effect before any dependent instructions are  
executed.  
c15, Secondary Auxiliary Control Register  
The Secondary Auxiliary Control Register is:  
a read/write register  
accessible in Privileged mode only.  
Note  
This register is implemented from the r1pm releases of the processor. Attempting to access this  
register in r0pm releases of the processor results in an Undefined Instruction exception.  
Figure 4-29 on page 4-42 shows the arrangement of bits in the register.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-41  
   
System Control Coprocessor  
31  
23 22 21 20 19 18 17 16 15 14 13 12 11 10 9  
8
7
4
3
2
1
0
Reserved  
DCHE  
ATCMRMW  
BTCMRMW  
DR2B  
DF6DI  
DF2DI  
DDI  
ATCMECC  
B0TCMECC  
Reserved  
IDC  
DZC  
IOC  
UFC  
DOODPFP  
DOOFMACS  
Reserved  
IXC  
OFC  
Figure 4-29 Secondary Auxiliary Control Register format  
Table 4-25 shows how the bit values correspond with the Secondary Auxiliary Control Register  
functions.  
Table 4-25 Secondary Auxiliary Control Register bit functions  
Function  
Bits  
Field  
[31:23] Reserved  
SBZ.  
Disable hard-error support in the caches.a  
[22]  
[21]  
DCHE  
DR2Bb  
0 = Enabled. The cache logic recovers from some hard errors. You must not use this value on  
revisions r1p2 or earlier of the processor.  
1 = Disabled. Most hard errors in the caches are fatal. This is the reset value.  
See Hard errors on page 8-5 for more information.  
Enable random 2-bit error generation in cache RAMs. This bit has no effect unless ECC is  
0 = Disabled. This is the reset value.  
1 = Enabled.  
Note  
This bit controls error generation logic during system validation. A synthesized ASIC  
typically does not have such models and this bit is therefore redundant for ASICs.  
F6 dual issue control.c  
0 = Enabled. This is the reset value.  
1 = Disabled.  
[20]  
[19]  
[18]  
[17]  
DF6DI  
DF2DI  
DDI  
F2_Id/F2_st/F2D dual issue control.c  
0 = Enabled. This is the reset value.  
1 = Disabled.  
F1/F3/F4dual issue control.c  
0 = Enabled. This is the reset value.  
1 = Disabled.  
Out-of-order Double Precision Floating Point instruction control.c  
0 = Enabled. This is the reset value.  
1 = Disabled.  
DOODPFP  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-42  
         
System Control Coprocessor  
Table 4-25 Secondary Auxiliary Control Register bit functions (continued)  
Bits  
Field  
Function  
Out-of-order FMACScontrol.c  
0 = Enabled. This is the reset value.  
1 = Disabled.  
[16]  
DOOFMACS  
[15:14] Reserved  
SBZ.  
Floating-point inexact exception output mask.c  
[13]  
[12]  
[11]  
[10]  
[9]  
IXC  
OFC  
UFC  
IOC  
DZC  
IDC  
0 = Mask floating-point inexact exception output. The output FPIXC is forced to zero. This  
is the reset value.  
1 = Propagate floating point inexact exception flag FPSCR.IXCto output FPIXC.  
Floating-point overflow exception output mask.c  
0 = Mask floating-point overflow exception output. The output FPOFC is forced to zero. This  
is the reset value.  
1 = Propagate floating-point overflow exception flag FPSCR.OFCto output FPOFC.  
Floating-point underflow exception output mask.c  
0 = Mask floating-point underflow exception output. The output FPUFC is forced to zero.  
This is the reset value.  
1 = Propagate floating-point underflow exception flag FPSCR.UFCto output FPUFC.  
Floating-point invalid operation exception output mask.c  
0 = Mask floating-point invalid operation exception output. The output FPIOC is forced to  
zero. This is the reset value.  
1 = Propagate floating-point invalid operation exception flag FPSCR.IOCto output FPIOC.  
Floating-point divide-by-zero exception output mask.c  
0 = Mask floating-point divide-by-zero exception output. The output FPDZC is forced to  
zero. This is the reset value.  
1 = Propagate floating-point divide-by-zero exception flag FPSCR.DZCto output FPDZC.  
Floating-point input denormal exception output mask.c  
[8]  
0 = Mask floating-point input denormal exception output. The output FPIDC is forced to zero.  
This is the reset value.  
1 = Propagate floating-point input denormal exception flag FPSCR.IDCto output FPIDC.  
[7:4}  
[3]  
Reserved  
SBZ.  
Correction for internal ECC logic on BTCM ports.d  
0 = Enabled. This is the reset value.  
1 = Disabled.  
BTCMECC  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-43  
   
System Control Coprocessor  
Table 4-25 Secondary Auxiliary Control Register bit functions (continued)  
Bits  
Field  
Function  
Correction for internal ECC logic on ATCM port.d  
0 = Enabled. This is the reset value.  
1 = Disabled.  
[2]  
ATCMECC  
[1]  
[0]  
BTCMRMW  
ATCMRMW  
Enables 64-bit stores for the BTCMs. When enabled, the processor uses read-modify-write to  
ensure that all reads and writes presented on the BTCM ports are 64 bits wide.e  
0 = Disabled  
1 = Enabled.  
The primary input RMWENRAM[1] defines the reset value.  
Enables 64-bit stores for the ATCM. When enabled, the processor uses read-modify-write to  
ensure that all reads and writes presented on the ATCM port are 64 bits wide.e  
0 = Disabled  
1 = Enabled.  
The primary input RMWENRAM[0] defines the reset value.  
a. This bit is RAZ if both caches have neither ECC nor parity.  
b. This bit is only supported if parity error generation is implemented in your design.  
c. This bit has no effect unless the Floating Point Unit (FPU) has been configured, see Configurable options on page 1-13.  
d. This bit has no effect unless TCM ECC logic has been configured for the respective TCM interface, see Configurable options  
e. This feature is not available when the TCM interface has been built with 32-bit ECC.  
To access the Secondary Auxiliary Control Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c15, c0, 0 ; Read Secondary Auxiliary Control Register  
MCR p15, 0, <Rd>, c15, c0, 0 ; Write Secondary Auxiliary Control Register  
ARM recommends that any instruction that changes bits [20:16] is followed by an ISB  
instruction to ensure that the changes have taken effect before any dependent instructions are  
executed.  
4.2.17 c1, Coprocessor Access Register  
The Coprocessor Access Register sets access rights for coprocessors CP0-CP13. This register  
has no effect on access to CP14, the debug control coprocessor, or CP15, the system control  
coprocessor. This register also provides a means for software to determine if any particular  
coprocessor, CP0-CP13, exists in the system.  
The Coprocessor Access Register is:  
a read/write register  
accessible in Privileged mode only.  
Because this processor does not support coprocessors CP0 through CP9, CP12, and CP13, bits  
[27:24] and [19:0] in this register are read-as-zero and ignore writes.  
Figure 4-30 shows the arrangement of bits in the register.  
31  
28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9  
8
7
6
5
4
3
2
1
0
Reserved cp13 cp12 cp11 cp10 cp9 cp8 cp7 cp6 cp5 cp4 cp3 cp2 cp1 cp0  
Figure 4-30 Coprocessor Access Register format  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-44  
         
System Control Coprocessor  
Table 4-26 shows how the bit values correspond with the Coprocessor Access Register  
functions.  
Table 4-26 Coprocessor Access Register bit functions  
Bits  
Field  
Function  
[31:28] Reserved SBZ.  
[27:0] Defines access permissions for each coprocessor.  
cp<n>a  
Access denied is the reset condition, and is the behavior for non-existent coprocessors.  
b00 = Access denied. Attempts to access generates an Undefined exception.  
b01 = Privileged mode access only  
b10 = Reserved  
b11 = Privileged and User mode access.  
Access permissions for the FPU are set by fields cp10 and cp11. For all other  
coprocessor fields, the value is fixed to b00.  
a. n is the coprocessor number between 0 and 13.  
To access the Coprocessor Access Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c1, c0, 2 ; Read Coprocessor Access Register  
MCR p15, 0, <Rd>, c1, c0, 2 ; Write Coprocessor Access Register  
4.2.18 Fault Status and Address Registers  
The processor reports the status and address of faults that occur during its operation. For both  
data and instruction faults there are two Fault Status Registers (FSRs) and one Fault Address  
Register (FAR).  
Fields within the Data and Instruction FSRs indicate the priority and source of a fault and the  
validity of the address in the corresponding FAR. Table 4-27 shows this encoding for the FSRs.  
Table 4-27 Fault Status Register encodings  
FSR  
[10,3:0]  
Priority Sources  
FAR  
Highest  
Alignment  
0b00001 Valid  
Background  
0b00000 Valid  
Permission  
0b01101 Valid  
Precise External Abort  
Imprecise External Abort  
Precise Parity/ECC Error  
Imprecise Parity/ECC Error  
Debug Event  
0b01000 Valid  
0b10110 Unpredictable  
0b11001 Valid  
0b11000 Unpredictable  
0b00010 Unchanged  
Lowest  
All other encodings for these FSR bits are Reserved.  
c5, Data Fault Status Register  
The Data Fault Status Register (DFSR) holds status information regarding the source of the last  
data abort.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-45  
           
System Control Coprocessor  
The Data Fault Status Register is:  
a read/write register  
accessible in Privileged mode only.  
Figure 4-31 shows the bit arrangement in the Data Fault Status Register.  
31  
13 12 11 10 9  
8
0
7
4
3
0
Reserved  
S
0
Domain  
Status  
RW  
SD  
Figure 4-31 Data Fault Status Register format  
Table 4-28 shows how the bit values correspond with the Data Fault Status Register functions.  
Table 4-28 Data Fault Status Register bit functions  
Bits  
Field  
Function  
[31:13]  
[12]  
Reserved SBZ.  
SD  
Distinguishes between an AXI Decode or Slave error on an external abort. This bit is only valid  
for external aborts. For all other aborts types of abort, this bit is set to zero:  
0 = AXI Decode error (DECERR) caused the abort  
1 = AXI Slave error (SLVERR, or OKAY in response to exclusive read transaction) caused the  
abort.  
[11]  
RW  
Indicates whether a read or write access caused an abort:  
0 = read access caused the abort  
1 = write access caused the abort.  
[10]a  
[9:8]  
[7:4]  
[3:0]a  
S
Part of the Status field.  
-
Always read as 0. Writes ignored.  
Domain  
Status  
SBZ. This is because domains are not implemented in this processor.  
Indicates the type of fault generated. To determine the data fault, you must use bit [12] and bit [10]  
in conjunction with bits [3:0].  
a. For more information on how these bits are used in reporting faults, see Table 4-27 on page 4-45.  
To use the DFSR read or write CP15 with:  
MRC p15, 0, <Rd>, c5, c0, 0 ; Read Data Fault Status Register  
MCR p15, 0, <Rd>, c5, c0, 0 ; Write Data Fault Status Register  
c5, Instruction Fault Status Register  
The Instruction Fault Status Register (IFSR) holds status information regarding the source of  
the last instruction abort.  
The Instruction Fault Status Register is:  
a read/write register  
accessible in Privileged mode only.  
Figure 4-32 on page 4-47 shows the bit arrangement in the Instruction Fault Status Register.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-46  
         
System Control Coprocessor  
31  
13 12 11 10 9  
S
8
7
4
3
0
Reserved  
Domain  
Status  
Reserved  
Reserved  
SD  
Figure 4-32 Instruction Fault Status Register format  
Table 4-29 shows how the bit values correspond with the Instruction Fault Status Register  
functions.  
Table 4-29 Instruction Fault Status Register bit functions  
Function  
Bits  
Field  
[31:13] Reserved SBZ.  
[12]  
SD  
Distinguishes between an AXI Decode or Slave error on an external abort. This bit is only valid for  
external aborts. For all other aborts types of abort, this bit is set to zero:  
0 = AXI Decode error (DECERR) caused the abort  
1 = AXI Slave error (SLVERR) caused the abort.  
[11]  
Reserved SBZ.  
[10]a  
[9:8]  
[7:4]  
[3:0]a  
S
Part of the Status field.  
Reserved SBZ.  
Domain  
Status  
SBZ. This is because domains are not implemented in this processor.  
Indicates the type of fault generated. To determine the instruction fault, bit [12] and bit [10] must  
be used in conjunction with bits [3:0].  
a. For more information on how these bits are used in reporting faults, see Table 4-27 on page 4-45.  
To access the IFSR read or write CP15 with:  
MRC p15, 0, <Rd>, c5, c0, 1 ; Read Instruction Fault Status Register  
MCR p15, 0, <Rd>, c5, c0, 1 ; Write Instruction Fault Status Register  
c5, Auxiliary Fault Status Registers  
There are two auxiliary fault status registers:  
the Auxiliary Data Fault Status Register (ADFSR)  
the Auxiliary Instruction Fault Status Register (AIFSR).  
These registers provide additional information about data and instruction parity, ECC, and  
external TCM errors.  
The auxiliary fault status registers are:  
read/write registers  
accessible in Privileged mode only.  
Figure 4-33 on page 4-48 shows the bit arrangement in the auxiliary fault status registers.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-47  
           
System Control Coprocessor  
31  
28 27  
24 23 22 21 20  
14 13  
5
4
0
Reserved  
Reserved  
Recoverable error  
Index  
Reserved  
CacheWay  
Side  
Figure 4-33 Auxiliary fault status registers format  
Table 4-30 shows how the bit values correspond with the auxiliary fault status register functions.  
Table 4-30 ADFSR and AIFSR bit functions  
Bits  
Field  
Function  
[31:28] Reserved  
SBZ.  
CacheWaya  
[27:24]  
The value returned in this field indicates the cache way or ways in which the error occurred.  
[23:22] Side  
The value returned in this field indicates the source of the error. Possible values are:  
b00 = Cache or AXI-master interface  
b01 = ATCM  
b10 = BTCM  
b11 = Reserved.  
[21]  
Recoverable The value returned in this field indicates if the error is recoverable.  
error  
0 = Unrecoverable error.  
1 = Recoverable error. This includes all correctable parity/ECC errors and recoverable  
TCM external errors.  
[20:14] Reserved  
SBZ.  
Indexb  
[13:5]  
[4:0]  
This field returns the index value for the access giving the error.  
SBZ.  
Reserved  
a. This field is only valid for data cache store parity/ECC errors, otherwise it is Unpredictable.  
b. This field is only valid for data cache store parity/ECC errors. On the AIFSR, and for TCM accesses, this field SBZ.  
To access the auxiliary fault status registers, read or write CP15 with:  
MCR p15, 0, <Rd>, c5, c1, 0 ; Write Auxiliary Data Fault Status Register  
MRC p15, 0, <Rd>, c5, c1, 0 ; Read Auxiliary Data Fault Status Register  
MCR p15, 0, <Rd>, c5, c1, 1 ; Write Auxiliary Instruction Fault Status Register  
MRC p15, 0, <Rd>, c5, c1, 1 ; Read Auxiliary Instruction Fault Status Register  
The contents of an auxiliary fault status register are only valid when the corresponding Data or  
Instruction Fault Status Register indicates that a parity error has occurred. At other times the  
contents of the auxiliary fault status registers are Unpredictable.  
c6, Data Fault Address Register  
The Data Fault Address Register (DFAR) holds the address of the fault when a precise abort  
occurs.  
The DFAR is:  
a read/write register  
accessible in Privileged mode only.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-48  
         
System Control Coprocessor  
The Data Fault Address Register bits [31:0] contain the address where the precise abort  
occurred.  
To access the DFAR read or write CP15 with:  
MRC p15, 0, <Rd>, c6, c0, 0 ; Read Data Fault Address Register  
MCR p15, 0, <Rd>, c6, c0, 0 ; Write Data Fault Address Register  
A write to this register sets the DFAR to the value of the data written. This is useful for a  
debugger to restore the value of the DFAR.  
The processor also updates the DFAR on debug exception entry because of watchpoints. See  
c6, Instruction Fault Address Register  
The purpose of the Instruction Fault Address Register (IFAR) is to hold the address of  
instructions that cause a prefetch abort.  
The IFAR is:  
a read/write register  
accessible in Privileged mode only.  
The Instruction Fault Address Register bits [31:0] contain the Instruction Fault address.  
To access the IFAR read or write CP15 with:  
MRC p15, 0, <Rd>, c6, c0, 2 ; Read Instruction Fault Address Register  
MCR p15, 0, <Rd>, c6, c0, 2 ; Write Instruction Fault Address Register  
A write to this register sets the IFAR to the value of the data written. This is useful for a  
debugger to restore the value of the IFAR.  
4.2.19 c6, MPU memory region programming registers  
The MPU memory region programming registers program the MPU regions.  
There is one register that specifies which one of the sets of region registers is to be accessed.  
to specify:  
region base address  
region size and enable  
region access control.  
You can implement the processor with eight or 12 regions, or without an MPU entirely. If you  
implement the processor without an MPU, then there are no regions and no region programming  
registers.  
Note  
When the MPU is enabled:  
The MPU determines the access permissions for all accesses to memory, including  
the TCMs. Therefore, you must ensure that the memory regions in the MPU are  
programmed to cover the complete TCM address space with the appropriate access  
permissions. You must define at least one of the regions in the MPU.  
An access to an undefined area of memory generates a background fault.  
For the TCM space the processor uses the access permissions but ignores the region  
attributes from MPU.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-49  
   
System Control Coprocessor  
CP15, c9 sets the location of the TCM base address. For more information see c9, BTCM  
c6, MPU Region Base Address Registers  
The MPU Region Base Address Registers describe the base address of the region specified by  
the Memory Region Number Register. The region base address must always align to the region  
size.  
The MPU Region Base Address Registers are:  
32-bit read/write registers  
accessible in Privileged mode only.  
Figure 4-34 shows the arrangement of bits in the registers.  
31  
5
4
0
Base address  
Reserved  
Figure 4-34 MPU Region Base Address Registers format  
Table 4-31 shows how the bit values correspond with the MPU Region Base Address Register  
functions.  
Table 4-31 MPU Region Base Address Registers bit functions  
Bits  
Field  
Base address Physical base address. Defines the base address of a region.  
Reserved SBZ  
Function  
[31:5]  
[4:0]  
To access an MPU Region Base Address Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c6, c1, 0 ; Read MPU Region Base Address Register  
MCR p15, 0, <Rd>, c6, c1, 0 ; Write MPU Region Base Address Register  
c6, MPU Region Size and Enable Registers  
The MPU Region Size and Enable Registers:  
specify the size of the region specified by the Memory Region Number Register  
identify the address ranges that are used for a particular region  
enable or disable the region, and its sub-regions, specified by the Memory Region  
Number Register.  
The MPU Region Size and Enable Registers are:  
32-bit read/write registers  
accessible in Privileged mode only.  
Figure 4-35 on page 4-51 shows the arrangement of bits in the registers.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-50  
           
System Control Coprocessor  
31  
16 15  
8
7
6
5
1
0
Reserved  
Sub-region disable  
Region size  
Reserved  
Enable  
Figure 4-35 MPU Region Size and Enable Registers format  
Table 4-32 shows how the bit values correspond with the MPU Region Size and Enable  
Registers.  
Table 4-32 Region Size Register bit functions  
Bits  
Field  
Function  
[31:16]  
[15:8]  
Reserved  
SBZ.  
Each bit position represents a sub-region, 0-7a.  
Bit [8] corresponds to sub-region 0  
...  
Sub-region disable  
Bit [15] corresponds to sub-region 7  
The meaning of each bit is:  
0 = address range is part of this region  
1 = address range is not part of this region.  
Reserved  
SBZ.  
[5:1]  
Region size  
Defines the region size:  
b00000 - b00011=Unpredictable  
b00100 = 32 bytes  
b00101 = 64 bytes  
b00110 = 128 bytes  
b00111 = 256 bytes  
b01000 = 512 bytes  
b01001 = 1KB  
b01100 = 8KB  
b10110 = 8MB  
b10111 = 16MB  
b11000 = 32MB  
b11001 = 64MB  
b11010 = 128MB  
b11011 = 256MB  
b11100 = 512MB  
b11101 = 1GB  
b01101 = 16KB  
b01110 = 32KB  
b01111 = 64KB  
b10000 = 128KB  
b10001 = 256KB  
b10010 = 512KB  
b10011 = 1MB  
b10100 = 2MB  
b10101 = 4MB  
b01010 = 2KB  
b11110 = 2GB  
b01011 = 4KB  
b11111 = 4GB.  
[0]  
Enable  
Enables or disables a memory region:  
0 = Memory region disabled. Memory regions are disabled on reset.  
1 = Memory region enabled. A memory region must be enabled before it is used.  
a. Sub-region 0 covers the least significant addresses in the region, while sub-region 7 covers the most significant  
addresses in the region. For more information, see Subregions on page 7-3.  
To access an MPU Region Size and Enable Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c6, c1, 2 ; Read Data MPU Region Size and Enable Register  
MCR p15, 0, <Rd>, c6, c1, 2 ; Write Data MPU Region Size and Enable Register  
Writing a region size that is outside the range results in Unpredictable behavior.  
c6, MPU Region Access Control Registers  
The MPU Region Access Control Registers hold the region attributes and access permissions  
for the region specified by the Memory Region Number Register.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-51  
           
System Control Coprocessor  
The MPU Region Access Control Registers are:  
read/write registers  
accessible in Privileged mode only.  
Figure 4-36 shows the arrangement of bits in the register.  
31  
13 12 11 10  
XN  
8
7
6
5
3
2
1
0
Reserved  
AP  
TEX  
S C B  
Reserved  
Figure 4-36 MPU Region Access Control Register format  
Table 4-33 shows how the bit values correspond with the Region Access Control Register  
functions.  
Table 4-33 MPU Region Access Control Register bit functions  
Function  
Bits  
Field  
Reserved SBZ.  
[31:13]  
[12]  
XN  
Execute never. Determines if a region of memory is executable:  
0 = all instruction fetches enabled  
1 = no instruction fetches enabled.  
[11]  
-
Reserved.  
[10:8]  
AP  
Access permission. Defines the data access permissions. For more information on AP bit values  
[7:6]  
[5:3]  
[2]  
Reserved SBZ.  
Type extension. Defines the type extension attributea.  
TEX  
S
Share. Determines if the memory region is Shared or Non-shared:  
0 = Non-shared.  
1 = Shared.  
This bit only applies to Normal, not Device or Strongly Ordered memory.  
C bita:  
B bita:  
[1]  
[0]  
C
B
a. For more information on this region attribute, see Table 7-3 on page 7-9.  
Table 4-34 shows the AP bit values that determine the permissions for Privileged and User data  
access.  
Table 4-34 Access data permission bit encoding  
AP bit values Privileged permissions User permissions Description  
b000  
b001  
b010  
No access  
Read/write  
Read/write  
No access  
No access  
Read-only  
All accesses generate a permission fault  
Privileged access only  
Writes in User mode generate permission  
faults  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-52  
               
System Control Coprocessor  
Table 4-34 Access data permission bit encoding (continued)  
AP bit values Privileged permissions User permissions Description  
b011  
b100  
b101  
b110  
b111  
Read/write  
UNP  
Read/write  
UNP  
Full access  
Reserved  
Read-only  
Read-only  
UNP  
No access  
Read-only  
UNP  
Privileged read-only  
Privileged/User read-only  
Reserved  
To access the MPU Region Access Control Registers read or write CP15 with:  
MRC p15, 0, <Rd>, c6, c1, 4 ; Read Region access control Register  
MCR p15, 0, <Rd>, c6, c1, 4 ; Write Region access control Register  
To execute instructions in User and Privileged modes:  
the region must have read access as defined by the AP bits  
the XN bit must be set to 0.  
c6, MPU Memory Region Number Register  
The MPU Region Registers are multiple registers with one register for each memory region  
implemented. The value contained in the MPU Memory Region Number Register determines  
which of the multiple registers is accessed.  
The MPU Memory Region Number Registers are:  
read/write register  
accessible in Privileged mode only.  
Figure 4-37 shows the arrangement of bits in the register.  
31  
4
3
0
Reserved  
Region  
Figure 4-37 MPU Memory Region Number Register format  
Table 4-35 shows how the bit values correspond with the MPU Memory Region Number  
Register bits.  
Table 4-35 MPU Memory Region Number Register bit functions  
Function  
Bits  
Field  
[31:4] Reserved SBZ.  
[3:0]  
Region  
Defines the group of registers to be accessed. Read the MPU Type Register to determine the number  
of supported regions, see c0, MPU Type Register on page 4-17.  
To access the MPU Memory Region Number Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c6, c2, 0 ; Read MPU Memory Region Number Register  
MCR p15, 0, <Rd>, c6, c2, 0 ; Write MPU Memory Region Number Register  
Writing this register with a value greater than or equal to the number of regions from the MPU  
Type Register is Unpredictable. Associated register bank accesses are also Unpredictable.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-53  
         
System Control Coprocessor  
4.2.20 Cache operations  
The purpose of c7 is to manage the associated caches. The maintenance operations are formed  
into two management groups:  
Set and Way:  
clean  
invalidate  
clean and invalidate.  
Address, usually labelled MVA for Modified Virtual Address, but on this processor all  
addresses are identical:  
clean  
invalidate  
clean and invalidate.  
In addition, the maintenance operations use these definitions:  
Point of Coherency (PoC)  
A point where all instruction, data, or translation-table walks are transparent to  
any processor in the system.  
Point of Unification (PoU)  
A point where instruction and data become unified and self-modifying code can  
function.  
Figure 4-38 on page 4-55 shows the arrangement of the functions in this group that operate with  
the MCRand MRCinstructions.  
Note  
The following operations, as Figure 4-38 on page 4-55 shows, are implemented as No  
Operation, NOP, on the processor:  
Wait For Interrupt, CRm= c0, Opcode_2 = 4  
Invalidate Entire Branch Predictor Array, CRm= c5, Opcode_2 = 6  
Invalidate Branch Predictor Array Line using MVA, CRm= c5, Opcode_2 = 7  
The Wait For Interrupt (WFI) instruction provides the Wait For Interrupt function. For more  
information see the ARM Architecture Reference Manual.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-54  
   
System Control Coprocessor  
CRn Opcode_1  
CRm Opcode_2  
SBZ  
SBZ  
MVA  
SBZ  
SBZ  
c7  
0
c0  
c5  
4
0
1
4
6
7
1
2
1
2
4
5
1
1
2
0
Wait For Interrupt (NOP)  
Invalidate All Instruction Caches  
Invalidate Instruction Cache Line to Point-of-Unification by MVA  
Flush Prefetch buffer  
Invalidate entire branch predictor array (NOP)  
Invalidate VA from Branch Predictor Array (NOP)  
Invalidate data cache line to Point-of-Coherency by MVA  
Invalidate data cache line by set/way  
Clean data cache line to Point-of-Coherency by MVA  
Clean data cache line by set/way  
Data Synchronization Barrier  
Data Memory Barrier  
Clean data cache line to Point-of-Unification by MVA  
Clean and Invalidate data cache line to Point-of-Unification by MVA  
Clean and Invalidate data cache line by set/way  
Invalidate all Data Caches  
MVA  
Way  
MVA  
Way  
SBZ  
SBZ  
MVA  
MVA  
Way  
SBZ  
c6  
c10  
c11  
c14  
c15  
0
c5  
Read-only  
Read/write  
Write-only  
Accessible in User mode  
SBZ  
MVA  
Way  
Should Be Zero  
Using MVA  
Using Set and Way  
Figure 4-38 Cache operations  
In addition to the register c7 cache management functions in this processor, an Invalidate all  
data caches operation is provided as a c15 operation. For convenience, that c15 operation is also  
described in this section.  
Note  
Writing c7 with a combination of CRm and Opcode_2 not listed in Figure 4-38 results in  
an Undefined exception.  
In this processor, reading from c7 causes an Undefined exception.  
All accesses to c7 can only be executed in a Privileged mode of operation, except for the  
Flush Prefetch Buffer, Data Synchronization Barrier, and Data Memory Barrier  
operations. These can be performed in User mode. Attempting to execute a Privileged  
instruction in User mode results in an Undefined exception.  
This processor does not contain an address-based branch predictor array.  
Invalidate and clean operations  
The terms that describe the invalidate, clean, and prefetch operations are defined in the ARM  
Architecture Reference Manual.  
You can perform invalidate and clean operations on:  
single cache lines  
entire caches.  
Set and Way format  
Figure 4-39 on page 4-56 shows the Set and Way format for invalidate and clean operations.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-55  
     
System Control Coprocessor  
31 30 29  
Way  
S+5 S+4  
5
4
0
Reserved  
Set  
Reserved  
Figure 4-39 c7 format for Set and Way  
Table 4-36 shows how the bit values correspond with the Cache Operation functions for Set and  
Way format operations.  
Table 4-36 Functional bits of c7 for Set and Way  
Bits  
Field  
Way  
Function  
[31:30]  
Indicates the cache way to invalidate or clean.  
[29:S+5] Reserved SBZ.  
[S+4:5]  
Set  
Indicates the cache set to invalidate or clean. Because the cache sizes are configurable, the width  
of the Set field is unique to the cache size. See Table 4-37.  
[4:0]]  
Reserved SBZ.  
Table 4-37 shows the cache sizes and the resultant bit range for Set.  
Table 4-37 Widths of the set field for L1 cache sizes  
Size  
Set  
4KB  
8KB  
[9:5]  
[10:5]  
16KB [11:5]  
32KB [12:5]  
64KB [13:5]  
See c0, Cache Type Register on page 4-15 for more information on cache sizes.  
Address format  
Figure 4-40 shows the address format for invalidate and clean operations.  
31  
5
4
0
Address  
Reserved  
Figure 4-40 Cache operations address format  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-56  
               
System Control Coprocessor  
Table 4-38 shows how the bit values correspond with the address format for invalidate and clean  
operations.  
Table 4-38 Functional bits of c7 for address format  
Bits  
Field  
Function  
[31:5] Address  
Specifies the address to invalidate or clean  
[4:0]  
Reserved SBZ  
Data Synchronization Barrier operation  
The purpose of the Data Synchronization Barrier operation is to ensure that all outstanding  
explicit memory transactions complete before any following instructions begin. This ensures  
that data in memory is up to date before the processor executes any more instructions.  
The Data Synchronization Barrier Register is:  
a write-only operation  
accessible in both User and Privileged mode.  
To access the Data Synchronization Barrier operation, write CP15 with:  
MCR p15, 0, <Rd>, c7, c10, 4 ; Data Synchronization Barrier operation  
For more information about memory barriers, see the ARM Architecture Reference Manual.  
Data Memory Barrier operation  
The purpose of the Data Memory Barrier operation is to ensure that all outstanding explicit  
memory transactions complete before any following explicit memory transactions begin. This  
ensures that data in memory is up to date before any memory transaction that depends on it.  
The Data Memory Barrier operation is:  
write-only  
accessible in User and Privileged mode.  
To access the Data Memory Barrier operation write CP15 with:  
MCR p15, 0, <Rd>, c7, c10,5 ; Data Memory Barrier Operation.  
For more information about memory barriers, see the ARM Architecture Reference Manual.  
4.2.21 c9, BTCM Region Register  
The BTCM Region Register holds the base address and size of the BTCM. It also determines if  
the BTCM is enabled.  
The BTCM Region Register is:  
a read/write register  
accessible in Privileged mode only.  
Figure 4-41 on page 4-58 shows the arrangement of bits in the register.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-57  
           
System Control Coprocessor  
31  
12 11  
7
6
2
1
0
Base address  
Reserved  
Size  
Reserved  
Enable  
Figure 4-41 BTCM Region Registers  
Table 4-39 shows how the bit values correspond with the BTCM Region Register.  
Table 4-39 BTCM Region Register bit functions  
Bits  
Field  
Function  
[31:12]  
Base  
address  
Base address. Defines the base address of the BTCM. The base address must be aligned to the  
size of the BTCM. Any bits in the range [(log2(RAMSize)-1):12] are ignored.  
At reset, if LOCZRAMA is set to:  
0 =The initial base address is 0x0  
.
1 =The initial base address is implementation-defined. See Configurable options on page 1-13.  
[11:7]  
[6:2]  
Reserved  
Size  
UNP on reads, SBZ on writes.  
Size. Indicates the size of the BTCM on reads. On writes this field is ignored. See About the  
b00000 = 0KB  
b00011 = 4KB  
b00100 = 8KB  
b00101 = 16KB  
b00110 = 32KB  
b00111 = 64KB  
b01000 = 128KB  
b01001 = 256KB  
b01010 = 512kB  
b01011 = 1MB  
b01100 = 2MB  
b01101 = 4MB  
b01110 = 8MB  
[1]  
[0]  
Reserved  
Enable  
SBZ.  
Enables or disables the BTCM.  
0 = Disabled  
1 = Enabled. The reset value of this field is determined by the INITRAMB input pin.  
To access the BTCM Region Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c9, c1, 0 ; Read BTCM Region Register  
MCR p15, 0, <Rd>, c9, c1, 0 ; Write BTCM Region Register  
4.2.22 c9, ATCM Region Register  
The ATCM Region Register holds the base address and size of the ATCM. It also determines if  
the ATCM is enabled.  
The ATCM Region Register is:  
a read/write register  
accessible in Privileged mode only.  
Figure 4-42 on page 4-59 shows the arrangement of bits in the register.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-58  
           
System Control Coprocessor  
31  
12 11  
7
6
2
1
0
Base address  
Reserved  
Size  
Reserved  
Enable  
Figure 4-42 ATCM Region Registers  
Table 4-40 shows how the bit values correspond with the ATCM Region Register.  
Table 4-40 ATCM Region Register bit functions  
Bits  
Field  
Function  
[31:12]  
Base  
address  
Base address. Defines the base address of the ATCM. The base address must be aligned to the  
size of the ATCM. Any bits in the range [(log2(RAMSize)-1):12] are ignored.  
At reset, if LOCZRAMA is set to:  
0 = The initial base address is implementation-defined. See Configurable options on page 1-13  
1 = The initial base address is 0x0  
.
[11:7]  
[6:2]  
Reserved  
Size  
UNP on reads, SBZ on writes.  
Size. Indicates the size of the ATCM on reads. On writes this field is ignored. See About the TCMs  
b00000 = 0KB  
b00011 = 4KB  
b00100 = 8KB  
b00101 = 16KB  
b00110 = 32KB  
b00111 = 64KB  
b01000 = 128KB  
b01001 = 256KB  
b01010 = 512kB  
b01011 = 1MB  
b01100 = 2MB  
b01101 = 4MB  
b01110 = 8MB.  
[1]  
[0]  
Reserved  
Enable  
SBZ  
Enables or disables the ATCM.  
0 = Disabled  
1 = Enabled. The reset value of this field is determined by the INITRAMA input pin.  
To access the ATCM Region Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c9, c1, 1 ; Read ATCM Region Register  
MCR p15, 0, <Rd>, c9, c1, 1 ; Write ATCM Region Register  
4.2.23 c9, TCM Selection Register  
The TCM Selection Register determines the TCM region register that the processor writes to.  
The processor only supports one TCM region for each TCM interface, and the TCM Selection  
Register Reads-As-Zero and ignores writes. It is only accessible in Privileged mode.  
4.2.24 c11, Slave Port Control Register  
The Slave Port Control Register enables or disables TCM access to the AXI slave port in  
Privileged or User mode.  
Note  
Use the Auxiliary Control Register to enable access to the cache RAMs through the AXI slave  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-59  
             
System Control Coprocessor  
The Slave Port Control Register is:  
a read/write register  
accessible in User and Privileged mode.  
Figure 4-43 shows the arrangement of bits in the register.  
31  
2
1
0
Reserved  
Privilege access  
AXI slave enable  
Figure 4-43 Slave Port Control Register  
Table 4-41 shows how the bit values correspond with the Slave Port Control Register functions.  
Table 4-41 Slave Port Control Register bit functions  
Bits  
Field  
Function  
[31:2] Reserved  
RAZ/UNP  
[1]  
[0]  
Privilege access  
Defines level of access for TCM accesses:  
0 = Non-privileged and privileged access, reset value  
1 = Privileged access only.  
AXI slave enable Enables or disables the AXI slave port for TCM accesses:  
0 = Enables AXI slave port, reset value  
1 = Disables AXI slave port.  
To access the Slave Port Control Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c11, c0, 0 ; Read Slave Port Control Register  
MCR p15, 0, <Rd>, c11, c0, 0 ; Write Slave Port Control Register  
4.2.25 c13, FCSE PID Register  
This processor does not support Fast Context Switch Extension (FCSE).  
The FCSE Process IDentifier (PID) Register is accessible in Privileged mode only. This register  
reads as zero and ignores writes.  
4.2.26 c13, Context ID Register  
The Context ID Register holds a process IDentification (ID) value for the currently-running  
process.  
The Embedded Trace Macrocell (ETM) and the debug logic use this register. The ETM can  
broadcast its value to indicate the process that is running currently. You must program each  
process with a unique number.  
The Context ID value can also enable process dependent breakpoints and instructions.  
The Context ID Register is:  
a read/write register  
accessible in Privileged mode only.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-60  
           
System Control Coprocessor  
The Context ID Register, bits [31:0] contain the process ID number.  
To use the Context ID Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c13, c0, 1 ; Read Context ID Register  
MCR p15, 0, <Rd>, c13, c0, 1 ; Write Context ID Register  
4.2.27 c13, Thread and Process ID Registers  
The Thread and Process ID Registers provide locations to store the IDs of software threads and  
processes for Operating System (OS) management purposes.  
The Thread and Process ID Registers are:  
three read/write registers:  
User read/write Thread and Process ID Register  
User read-only Thread and Process ID Register  
Privileged-only Thread and Process ID Register.  
each accessible in different modes:  
The User read/write register can be read and written in User and Privileged modes.  
The User read-only register can only be read in User mode, but can be read and  
written in Privileged modes.  
The Privileged-only register can be read and written in Privileged modes only.  
To access the Thread and Process ID registers, read or write CP15 with:  
MRC p15, 0, <Rd>, c13, c0, 2 ; Read User read/write Thread and Proc. ID Register  
MCR p15, 0, <Rd>, c13, c0, 2 ; Write User read/write Thread and Proc. ID Register  
MRC p15, 0, <Rd>, c13, c0, 3 ; Read User Read Only Thread and Proc. ID Register  
MCR p15, 0, <Rd>, c13, c0, 3 ; Write User Read Only Thread and Proc. ID Register  
MRC p15, 0, <Rd>, c13, c0, 4 ; Read Privileged Only Thread and Proc. ID Register  
MCR p15, 0, <Rd>, c13, c0, 4 ; Write Privileged Only Thread and Proc. ID Register  
Reading or writing the Thread and Process ID registers has no effect on processor state or  
operation. These registers provide OS support, and the OS must manage them.  
You must clear the contents of all Thread and Process ID registers on process switches to  
prevent data leaking from one process to another. This is important to ensure the security of data.  
The reset value of these registers is 0.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-61  
 
System Control Coprocessor  
4.2.28 Validation Registers  
The processor implements a set of validation registers. This section describes:  
c15, nVAL IRQ Enable Set Register  
The nVAL IRQ Enable Set Register enables any of the PMC Registers, PMC0-PMC2, and  
CCNT, to generate an interrupt request on overflow. If enabled, the interrupt request is signaled  
by nVALIRQ being asserted LOW.  
The nVAL IRQ Enable Set Register is:  
A read/write register.  
Always accessible in Privileged mode. The USEREN Register determines access, see c9,  
Figure 4-44 shows the bit arrangement for the nVAL IRQ Enable Set Register.  
31  
3
2
1
0
C
Reserved  
Cycle count overflow IRQ request enable  
P2  
P1  
P0  
Performance monitor counter  
overflow IRQ request enables  
Figure 4-44 nVAL IRQ Enable Set Register format  
Table 4-42 shows how the bit values correspond with the nVAL IRQ Enable Set Register.  
Table 4-42 nVAL IRQ Enable Set Register bit functions  
Bits  
Field  
Function  
[31]  
C
CCNT overflow IRQ request  
[30: 3] Reserved UNP or SBZP  
[2]  
[1]  
[0]  
P2  
P1  
P0  
PMC2 overflow IRQ request  
PMC1 overflow IRQ request  
PMC0 overflow IRQ request  
To access the nVAL IRQ Enable Set Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c15, c1, 0 ; Read nVAL IRQ Enable Set Register  
MCR p15, 0, <Rd>, c15, c1, 0 ; Write nVAL IRQ Enable Set Register  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-62  
             
System Control Coprocessor  
On reads, this register returns the current setting. On writes, interrupt requests can be enabled.  
If an interrupt request has been enabled it is disabled by writing to the nVAL IRQ Enable Clear  
If one or more of the IRQ request fields (P2, P1, P0, and C) is enabled, and the corresponding  
counter overflows, then an IRQ request is indicated by nVALIRQ being asserted LOW. This  
signal might be passed to a system interrupt controller.  
c15, nVAL FIQ Enable Set Register  
The nVAL FIQ Enable Set Register enables any of the PMC Registers, PMC0-PMC2, and  
CCNT, to generate an fast interrupt request on overflow. If enabled, the interrupt request is  
signaled by nVALFIQ being asserted LOW.  
The nVAL FIQ Enable Set Register is:  
A read/write register.  
Always accessible in Privileged mode. The USEREN Register determines access, see c9,  
Figure 4-45 shows the bit arrangement for the nVAL FIQ Enable Set Register.  
31  
3
2
1
0
C
Reserved  
Cycle count overflow FIQ request enable  
P2  
P1  
P0  
Performance monitor counter  
overflow FIQ request enables  
Figure 4-45 nVAL FIQ Enable Set Register format  
Table 4-43 shows how the bit values correspond with the nVAL FIQ Enable Set Register.  
Table 4-43 nVAL FIQ Enable Set Register bit functions  
Bits  
Field  
Function  
[31]  
C
CCNT overflow FIQ request  
[30:3] Reserved UNP or SBZP  
[2]  
[1]  
[0]  
P2  
P1  
P0  
PMC2 overflow FIQ request  
PMC1 overflow FIQ request  
PMC0 overflow FIQ request  
To access the FIQ Enable Set Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c15, c1, 1 ; Read FIQ Enable Set Register  
MCR p15, 0, <Rd>, c15, c1, 1 ; Write FIQ Enable Set Register  
On reads, this register returns the current setting. On writes, interrupt requests can be enabled.  
If an interrupt request has been enabled it is disabled by writing to the FIQ Enable Clear  
If one or more of the FIQ request fields (P2, P1, P0, and C) is enabled, and the corresponding  
counter overflows, then an FIQ request is indicated by nVALFIQ being asserted LOW. This  
signal can be passed to a system interrupt controller.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-63  
         
System Control Coprocessor  
c15, nVAL Reset Enable Set Register  
The nVAL Reset Enable Set Register enables any of the PMC Registers, PMC0-PMC2, and  
CCNT, to generate a reset request on overflow. If enabled, the reset request is signaled by  
nVALRESET being asserted LOW.  
The nVAL Reset Enable Set Register is:  
A read/write register.  
Always accessible in Privileged mode. The USEREN Register determines access, see c9,  
Figure 4-46 shows the bit arrangement for the nVAL Reset Enable Set Register.  
31  
3
2
1
0
C
Reserved  
Cycle count overflow reset request enable  
P2  
P1  
P0  
Performance monitor counter  
overflow reset request enables  
Figure 4-46 nVAL Reset Enable Set Register format  
Table 4-44 shows how the bit values correspond with the nVAL Reset Enable Set Register.  
Table 4-44 nVAL Reset Enable Set Register bit functions  
Bits  
Field  
Function  
[31]  
C
CCNT overflow reset request  
[30:3] Reserved UNP or SBZP  
[2]  
[1]  
[0]  
P2  
P1  
P0  
PMC2 overflow reset request  
PMC1 overflow reset request  
PMC0 overflow reset request  
To access the nVAL Reset Enable Set Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c15, c1, 2 ; Read nVAL Reset Enable Set Register  
MCR p15, 0, <Rd>, c15, c1, 2 ; Write nVAL Reset Enable Set Register  
On reads, this register returns the current setting. On writes, reset requests can be enabled. If a  
reset request has been enabled, it is disabled by writing to the nVAL Reset Enable Clear  
If one or more of the reset request fields (P2, P1, P0, and C) is enabled, and the corresponding  
counter overflows, then a reset request is indicated by nVALRESET being asserted LOW. This  
signal can be passed to a system reset controller.  
c15, nVAL Debug Request Enable Set Register  
The Debug Request Enable Set Register enables any of the PMC Registers, PMC0-PMC2, and  
CCNT, to generate a debug request on overflow. If enabled, the debug request is signaled by  
VALEDBGRQ being asserted HIGH.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-64  
           
System Control Coprocessor  
The nVAL Debug Request Enable Set Register is:  
A read/write register.  
Always accessible in Privileged mode. The USEREN Register determines access, see c9,  
Figure 4-47 shows the bit arrangement for the nVAL Debug Request Enable Set Register.  
31  
C
3
2
1
0
Reserved  
Cycle count overflow debug request enable  
P2  
P1  
P0  
Performance monitor counter  
overflow debug request enables  
Figure 4-47 nVAL Debug Request Enable Set Register format  
Table 4-45 shows how the bit values correspond with the nVAL Debug Request Enable Set  
Register.  
Table 4-45 nVAL Debug Request Enable Set Register bit functions  
Bits  
Field  
Function  
[31]  
C
CCNT overflow debug request  
[30:3] Reserved UNP or SBZP  
[2]  
[1]  
[0]  
P2  
P1  
P0  
PMC2 overflow debug request  
PMC1 overflow debug request  
PMC0 overflow debug request  
To access the nVAL Debug Request Enable Set Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c15, c1, 3 ; Read nVAL Debug Request Enable Set Register  
MCR p15, 0, <Rd>, c15, c1, 3 ; Write nVAL Debug Request Enable Set Register  
On reads, this register returns the current setting. On writes, debug requests can be enabled. If  
a debug request has been enabled, it is disabled by writing to the nVAL Debug Request Enable  
If one or more of the reset request fields (P2, P1, P0, and C) is enabled, and the corresponding  
counter overflows, then a debug reset request is indicated by VALEDBGRQ being asserted  
HIGH. This signal can be passed to an external debugger.  
c15, nVAL IRQ Enable Clear Register  
The nVAL IRQ Enable Clear Register disables overflow IRQ requests from any of the PMC  
Registers, PMC0-PMC2, and CCNT, for which they have been enabled.  
The nVAL IRQ Enable Clear Register is:  
A read/write register.  
Always accessible in Privileged mode. The USEREN Register determines access, see c9,  
Figure 4-48 on page 4-66 shows the bit arrangement for the nVAL IRQ Enable Clear Register.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-65  
         
System Control Coprocessor  
31  
C
3
2
1
0
Reserved  
P2  
P1  
P0  
Cycle count overflow  
IRQ request disable  
Performance monitor counter  
overflow IRQ request disables  
Figure 4-48 nVAL IRQ Enable Clear Register format  
Table 4-46 shows how the bit values correspond with the nVAL IRQ Enable Clear Register.  
Table 4-46 nVAL IRQ Enable Clear Register bit functions  
Bits  
Field  
Function  
[31]  
C
CCNT overflow IRQ request  
[30:3] Reserved UNP or SBZP  
[2]  
[1]  
[0]  
P2  
P1  
P0  
PMC2 overflow IRQ request  
PMC1 overflow IRQ request  
PMC0 overflow IRQ request  
To access the nVAL IRQ Enable Clear Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c15, c1, 4 ; Read nVAL IRQ Enable Clear Register  
MCR p15, 0, <Rd>, c15, c1, 4 ; Write nVAL IRQ Enable Clear Register  
On reads, this register returns the current setting. On writes, overflow interrupt requests that are  
currently enabled can be disabled.  
For more information of how to enable IRQ requests on counter overflows, and how the requests  
c15, nVAL FIQ Enable Clear Register  
The nVAL FIQ Enable Clear Register disables overflow FIQ requests from any of the PMC  
Registers, PMC0-PMC2, and CCNT, that are enabled.  
The nVAL FIQ Enable Clear Register is:  
A read/write register.  
Always accessible in Privileged mode. The USEREN Register determines access mode,  
Figure 4-49 shows the bit arrangement for the nVAL FIQ Enable Clear Register.  
31  
3
2
1
0
C
Reserved  
P2  
P1  
P0  
Cycle count overflow  
FIQ request disable  
Performance monitor counter  
overflow FIQ request disables  
Figure 4-49 nVAL FIQ Enable Clear Register format  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-66  
             
System Control Coprocessor  
Table 4-47 shows how the bit values correspond with the FIQ Enable Clear Register.  
Table 4-47 nVAL FIQ Enable Clear Register bit functions  
Bits  
Field  
Function  
[31]  
C
CCNT overflow FIQ request  
[30:3] Reserved UNP or SBZP  
[2]  
[1]  
[0]  
P2  
P1  
P0  
PMC2 overflow FIQ request  
PMC1 overflow FIQ request  
PMC0 overflow FIQ request  
To access the FIQ Enable Clear Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c15, c1, 5 ; Read FIQ Enable Clear Register  
MCR p15, 0, <Rd>, c15, c1, 5 ; Write FIQ Enable Clear Register  
On reads, this register returns the current setting. On writes, overflow interrupt requests that are  
currently enabled can be disabled.  
For information on how to enable FIQ requests on counter overflows, and how the requests are  
c15, nVAL Reset Enable Clear Register  
The nVAL Reset Enable Clear Register disables overflow reset requests from any of the PMC  
Registers, PMC0-PMC2, and CCNT, that are enabled.  
The nVAL Reset Enable Clear Register is:  
A read/write register.  
Always accessible in Privileged mode. The USEREN Register determines access, see c9,  
Figure 4-50 shows the bit arrangement for the nVAL Reset Enable Clear Register.  
31  
3
2
1
0
C
Reserved  
P2  
P1  
P0  
Cycle count overflow  
reset request disable  
Performance monitor counter overflow  
reset request disables  
Figure 4-50 nVAL Reset Enable Clear Register format  
Table 4-48 shows how the bit values correspond with the nVAL Reset Enable Clear Register.  
Table 4-48 nVAL Reset Enable Clear Register bit functions  
Bits  
Field  
Function  
[31]  
C
CCNT overflow reset request  
[30:3] Reserved UNP or SBZP  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-67  
             
System Control Coprocessor  
Table 4-48 nVAL Reset Enable Clear Register bit functions (continued)  
Bits  
Field  
Function  
[2]  
[1]  
[0]  
P2  
P1  
P0  
PMC2 overflow reset request  
PMC1 overflow reset request  
PMC0 overflow reset request  
To access the nVAL Reset Enable Clear Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c15, c1, 6 ; Read nVAL Reset Enable Clear Register  
MCR p15, 0, <Rd>, c15, c1, 6 ; Write nVAL Reset Enable Clear Register  
On reads, this register returns the current setting. On writes, overflow reset requests that are  
currently enabled can be disabled.  
For more information of how to enable reset requests on counter overflows, and how the  
c15, nVAL Debug Request Enable Clear Register  
The nVAL Debug Request Enable Clear Register disables overflow debug requests from any of  
the PMC Registers, PMC0-PMC2, and CCNT, that are enabled.  
The nVAL Debug Request Enable Clear Register is:  
A read/write register.  
Always accessible in Privileged mode. The USEREN Register determines access, see c9,  
Figure 4-51 shows the bit arrangement for the nVAL Debug Request Enable Clear Register.  
31  
C
3
2
1
0
Reserved  
P2  
P1  
P0  
Cycle count overflow  
debug request disable  
Performance monitor counter overflow  
debug request disables  
Figure 4-51 nVAL Debug Request Enable Clear Register format  
Table 4-49 shows how the bit values correspond with the nVAL Debug Request Enable Clear  
Register.  
Table 4-49 nVAL Debug Request Enable Clear Register bit functions  
Bits  
Field  
Function  
[31]  
C
CCNT overflow debug request  
[30:3] Reserved UNP or SBZP  
[2]  
[1]  
[0]  
P2  
P1  
P0  
PMC2 overflow debug request  
PMC1 overflow debug request  
PMC0 overflow debug request  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-68  
         
System Control Coprocessor  
To access the nVAL Debug Request Enable Clear Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c15, c1, 7 ; Read nVAL Debug Request Enable Clear Register  
MCR p15, 0, <Rd>, c15, c1, 7 ; Write nVAL Debug Request Enable Clear Register  
On reads, this register returns the current setting. On writes, overflow debug requests that are  
currently enabled can be disabled.  
For more information of how to enable debug requests on counter overflows, and how the  
c15, nVAL Cache Size Override Register  
The nVAL Cache Size Override Register overwrites the caches size fields in the main register.  
This enables you to choose a smaller instruction and data cache size than is implemented.  
The nVAL Cache Size Override Register is:  
a write-only register  
only accessible in Privileged mode.  
Figure 4-52 shows the bit arrangement for the nVAL Cache Size Override Register.  
31  
16 15  
8 7  
4
3
0
Dcache  
Reserved  
Icache  
Figure 4-52 nVAL Cache Size Override Register format  
Table 4-50 shows how the bit values correspond with the nVAL Cache Size Override Register.  
Table 4-50 nVAL Cache Size Override Register  
Bits  
Field  
Function  
[31:8] Reserved SBZ.  
[7:4]  
[3:0]  
Dcache  
Icache  
Defines the nVAL data cache size. See Table 4-51.  
Defines the nVAL instruction cache size. See Table 4-51.  
Table 4-51 shows the encodings for the nVAL instruction and data cache sizes.  
Table 4-51 nVAL instruction and data cache size encodings  
Encoding Instruction and data cache size  
b0000  
b0001  
b0011  
b0111  
b1111  
4kB  
8kB  
16kB  
32kB  
64kB  
To access the nVAL Cache Size Override Register, write CP15 with:  
MCR p15, 0, <Rd>, c15, c14, 0 ; nVAL Cache Size Override Register  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-69  
             
System Control Coprocessor  
Note  
The nVAL Cache Size Override Register can only be used to select cache sizes for which the  
appropriate RAM has been integrated. Larger cache sizes require deeper data and tag RAMs,  
and smaller cache sizes require wider tag RAMs. Therefore, it is unlikely that you can change  
the cache size using this register except using a simulation model of the cache RAMs.  
4.2.29 Correctable Fault Location Register  
The Correctable Fault Location Register (CFLR) indicates the location of the last correctable  
error that occurred during cache or TCM operations. It is not updated on speculative accesses,  
for example, an instruction fetch for an instruction that is not executed because of a previous  
branch. This register is:  
a read/write register  
accessible in Privileged mode only.  
Note  
This register is implemented from the r1pm releases of the processor. Attempting to access this  
register in r0pm releases of the processor results in an Undefined Instruction exception.  
The processor updates this register regardless of whether an abort is taken or an access is retried  
in response to the error.  
This register is updated on:  
parity or ECC errors in the instruction cache  
single-bit ECC errors in the data cache  
parity or multi-bit errors in the data cache when write-through behavior is forced  
single-bit TCM ECC errors.  
The CFLR is not updated on a TCM external error or external retry request.  
Every correctable error that causes a CFLR update also has an associated event. See Table 6-1  
on page 6-2 for the events which are related to CFLR updates. If two correctable errors occur  
simultaneously, for example an AXI slave error and an LSU or PFU error, the LSU or PFU write  
takes priority. If multiple errors occur, the value in the CFLR reflects the location of the latest  
event.  
The same register is updated by all correctable errors. You can read bits [25:24] to determine  
whether the error was from a cache or TCM access. Figure 4-53 shows the bit arrangement of  
the CFLR when it indicates a correctable cache error.  
31 30 29  
26 25 24 23  
Side  
14 13  
5
4
2
1
0
Way  
Reserved  
Reserved  
Index  
Type  
Reserved  
Figure 4-53 Correctable Fault Location Register - cache  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-70  
       
System Control Coprocessor  
Table 4-52 shows how the bit values correspond to the CFLR when it indicates a correctable  
cache error.  
Table 4-52 Correctable Fault Location Register - cache  
Bits  
Field  
Function  
[31:30] Reserved RAZ  
[29:26] Way  
[25:24] Side  
Indicates the Way of the error.  
Indicates the source of the error. For cache errors, this value is always 0b00  
.
[23:14] Reserved RAZ  
[13:5]  
[4:2]  
[1:0]  
Index  
Indicates the index of the location where the error occurred.  
Reserved RAZ  
Type Indicates the type of access that caused the error.  
0b00= Instruction cache.  
0b01= Data cache.  
Figure 4-54 shows the bit arrangement of the CFLR when it indicates a correctable TCM error.  
31  
26 25 24 23 22  
Side  
3
2
1
0
Reserved  
Address[22:3]  
Type  
Reserved  
Reserved  
Figure 4-54 Correctable Fault Location Register - TCM  
Table 4-53 shows how the bit values correspond to the CFLR when it indicates a correctable  
TCM error.  
Table 4-53 Correctable Fault Location Register - TCM  
Bits  
Field  
Function  
[31:26] Reserved RAZ  
[25:24] Side Indicates the source of the error.  
0b01= ATCM  
0b10= BTCM  
[23]  
[22:3]  
[2]  
Reserved RAZ  
Address  
Indicates the address in the TCM where the error occurred.  
Reserved RAZ  
[1:0]  
Type Indicates the type of access that caused the error.  
0b00= Instruction.  
0b01= Data.  
0b10 0b11= AXI slave.  
,
To access the Correctable Fault Location Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c15, c3, 0 : Read CFLR  
MCR p15, 0, <Rd>, c15, c3, 0 : Write CFLR  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-71  
           
System Control Coprocessor  
4.2.30 Build Options Registers  
Build options registers reflect the build configuration options used to build the processor. They  
do not reflect any pin-configuration options. These registers are:  
read-only registers  
accessible in Privileged mode only.  
Note  
These registers are implemented from the r1pm releases of the processor. Attempting to access  
these registers in r0pm releases of the processor results in an Undefined Instruction exception.  
c15, Build Options 1 Register  
Figure 4-55 shows the bit arrangement for the Build Options 1 Register.  
31  
12 11  
0
TCM_HI_INIT_ADDR  
Reserved  
Figure 4-55 Build Options 1 Register format  
Table 4-54 shows how the bit values correspond with the Build Options 1 Register.  
Table 4-54 Build Options 1 Register  
Function  
[31:12] TCM_HI_INIT_ADDR Default high address for the TCM.  
[11:0] Reserved SBZ  
Bits  
Field  
To access the Build Options 1 Register, write CP15 with:  
MRC p15, 0, <Rd>, c15, c2, 0 ; read Build Options 1 Register  
c15, Build Options 2 Register  
Figure 4-56 on page 4-73 shows the bit arrangement for the Build Options 2 Register.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-72  
               
System Control Coprocessor  
31 30 29 28 27 26 25 24 23 22 21 20 19  
17 16  
14 13 12 11 10 9  
8
7
6
5
4
3
2
0
DUAL_CORE  
DUAL_NCLK  
NO_ICACHE  
NO_DCACHE  
ATCM_ES  
BTCM_ES  
NO_IE  
NO_FPU  
NO_MPU  
MPU_REGIONS  
BREAK_POINTS  
WATCH_POINTS  
NO_A_TCM_INF  
NO_B0_TCM_INF  
NO_B1_TCM_INF  
TCMBUSPARITY  
NO_SLAVE  
ICACHE_ES  
DCACHE_ES  
N0_HARD_ERROR_CACHE  
AXIBUSPARITY  
RESERVED  
Figure 4-56 Build Options 2 Register format  
Table 4-55 shows how the bit values correspond with the Build Options 2 Register.  
Table 4-55 Build Options 2 Register  
Bits  
Field  
Function  
DUAL_COREa  
[31]  
Indicates whether a second, redundant, copy of the processor logic and  
checking logic was instantiated:  
0 = single core  
1 = dual core.  
DUAL_NCLKa  
NO_ICACHE  
NO_DCACHE  
[30]  
[29]  
[28]  
Indicates whether an inverted clock is used for the redundant core:  
0 = inverted clock not used  
1 = inverted clock used.  
Indicates whether the processor contains instruction cache:  
0 = processor contains instruction cache  
1 = processor does not contain instruction cache.  
Indicates whether the processor contains data cache:  
0 = processor contains data cache  
1 = processor does not contain data cache.  
[27:26] ATCM_ES  
Indicates whether an error scheme is implemented on the ATCM interface:  
00 = no error scheme  
01 = 8-bit parity logic  
10 = 32-bit error detection and correction  
11 = 64-bit error detection and correction.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-73  
         
System Control Coprocessor  
Table 4-55 Build Options 2 Register (continued)  
Bits  
Field  
Function  
[25:24] BTCM_ES  
Indicates whether an error scheme is implemented on the BTCM interface(s):  
00 = no error scheme  
01 = 8-bit parity logic  
10 = 32-bit error detection and correction  
11 = 64-bit error detection and correction.  
[23]  
[22]  
[21]  
[20]  
NO_IE  
Indicates whether the processor supports big-endian instructions:  
0 = processor supports big-endian instructions  
1 = processor does not support big-endian instructions.  
NO_FPU  
Indicates whether the processor contains a floating point unit:  
0 = processor contains a floating point unit  
1 = processor does not contain a floating point unit.  
NO_MPU  
MPU_REGIONS  
Indicates whether the processor contains a Memory Protection Unit (MPU):  
0 = processor contains an MPU  
1 = processor does not contain an MPU.  
Indicates the number of regions in the included MPU:  
0 = 8  
1 = 12.  
If the processor does not contain an MPU (bit [21] set to 0), this bit is set to 0.  
[19:17] BREAK_POINTS  
[16:14] WATCH_POINTS  
Indicates the number of break points implemented in the processor, minus 1.  
Indicates the number of watch points implemented in the processor, minus 1.  
[13]  
[12]  
[11]  
[10]  
[9]  
NO_A_TCM_INF  
NO_B0_TCM_INF  
NO_B1_TCM_INF  
TCMBUSPARITY  
NO_SLAVE  
Indicates whether the processor contains an ATCM port:  
0 = processor contains ATCM port  
1 = processor does not contain ATCM port.  
Indicates whether the processor contains a B0TCM port:  
0 = processor contains B0TCM port  
1 = processor does not contain B0TCM port.  
Indicates whether the processor contains a B1TCM port:  
0 = processor contains B1TCM port  
1 = processor does not contain B1TCM port.  
Indicates whether the processor contains TCM address bus parity logic:  
0 = processor does not contain TCM address bus parity logic  
1 = processor contains TCM address bus parity logic.  
Indicates whether the processor contains an AXI slave port:  
0 = processor contains an AXI slave port  
1 = processor does not contain an AXI slave port.  
[8:7]  
ICACHE_ES  
Indicates whether an error scheme is implemented for the instruction cache:  
00 = no error scheme  
01 = 8-bit parity error detection  
11 = 64-bit error detection and correction.  
If the processor does not contain an i-cache, these bits are set to 00.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-74  
System Control Coprocessor  
Table 4-55 Build Options 2 Register (continued)  
Bits  
Field  
Function  
[6:5]  
DCACHE_ES  
Indicates whether an error scheme is implemented for the data cache:  
00 = no error scheme  
01 = 8-bit parity error detection  
10 = 32-bit error detection and correction.  
If the processor does not contain a d-cache, these bits are set to 00.  
[4]  
NO_HARD_ERROR_CACH  
E
Indicates whether the processor contains cache for corrected TCM errors:  
0 = processor contains TCM error cache  
1 = processor does not contain TCM error cache.  
[3]  
AXIBUSPARITY  
Reserved  
Indicates whether the processor contains AXI bus parity logic.  
0 = processor does not contain AXI bus parity logic  
1 = processor contains AXI bus parity logic.  
[2:0]  
Undefined.  
a. The value of this bit is UNPREDICTABLE in revision r1p0 of the processor.  
To access the Build Options 2 Register, write CP15 with:  
MRC p15, 0, <Rd>, c15, c2, 1 ; read Build Options 2 Register  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
4-75  
Chapter 5  
Prefetch Unit  
This chapter describes how the PreFetch Unit (PFU), in conjunction with the DPU, uses program  
flow prediction to locate branches in the instruction stream and the strategies used to determine if  
a branch is likely to be taken or not. It contains the following sections:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
5-1  
   
PrefetchUnit  
5.1  
About the prefetch unit  
The purpose of the PFU is to:  
perform speculative fetch of instructions ahead of the DPU by predicting the outcome of  
branch instructions  
format instruction data in a way that aids the DPU in efficient implementation.  
The PFU fetches instructions from the memory system under the control of the DPU, and the  
internal coprocessors CP14 and CP15. In ARM state the memory system can supply up to two  
instructions per cycle. In Thumb state the memory system can supply up to four instructions per  
cycle.  
The PFU buffers up to three instruction data fetches in its FIFO. There is an additional FIFO  
between the PFU and the DPU that can normally buffer up to eight instructions. This reduces or  
eliminates stall cycles after a branch instruction. This increases the performance of the  
processor.  
Program flow prediction occurs in the PFU by:  
predicting the outcome of conditional branches using the branch predictor and, for direct  
branches, calculating their destination address using the offset encoded in the instruction  
predicting the destination of procedure returns using the return stack.  
The DPU resolves the program flow predictions that the PFU makes.  
The PFU fetches the instruction stream as dictated by:  
the Program Counter  
the branch predictor  
procedure returns signaled by the return stack  
exceptions including aborts and interrupts signaled by the DPU  
correction of mispredicted branches as indicated by the DPU.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
5-2  
   
PrefetchUnit  
5.2  
Branch prediction  
The PFU normally fetches instructions from sequential addresses. If a branch instruction is  
fetched, the next instruction to be fetched can only be determined with certainty after the  
instruction has completed execution at the end of the pipeline in the DPU. If the branch is taken,  
the next instruction to be executed is not sequential. The sequential instructions that the PFU  
has fetched while the branch instruction was executing must be flushed from the pipeline and  
the correct instruction fetched. This has the effect of reducing the performance of the processor.  
The PFU can detect branches in the Pd-stage of the pipeline, predict whether or not the branch  
is taken, and determine or predict the target address for a taken branch. This enables the PFU to  
start fetching instructions at the destination of a taken branch before the branch has completed  
execution in the DPU. The branch instruction is still executed in the DPU to determine the  
accuracy of the prediction. If the branch was mispredicted, the pipeline must be flushed and the  
correct instruction fetched. In general, more branches are correctly predicted than mispredicted  
so fewer pipeline flushes occur and the performance of the processor is enhanced.  
Two major classes of branch are addressed in the processor prediction scheme:  
1.  
Direct branches, including  
B
,
BL, CZB, and BLXimmediate, where the target address is a  
fixed offset, encoded in the instruction, from the program counter. If such an instruction  
has been fetched, and the program counter is known, predicting the destination of the  
branch only involves predicting whether the instruction passes or fails its condition code,  
that is, whether the branch is taken or not taken.  
2.  
Indirect branches such as load and Branch and eXchange (BX), instructions which write to  
the PC, that can be identified as a likely return from a procedure call. Two identifiable  
cases are:  
loads to the PC from an address derived from R13  
BX from R0-R14.  
In these cases, if the calling operation can also be identified, the likely return address can  
be stored in the return stack. Typical calling operations are BLand BLXinstructions.  
Note  
Unconditional instructions of either class of program flow are always executed, and do not  
affect prediction history. Unconditional return stack operations always affect the return stack.  
This section describes:  
5.2.1  
Disabling program flow prediction  
You cannot disable program flow prediction using the Z bit, bit [11], of CP15 Register c1. The  
Z bit is tied to 1. To disable the program flow prediction you must disable the return stack and  
set the branch prediction policy to not-taken. For more information see c1, System Control  
You can also control the return stack, the branch predictor, and the fetch rate using the Auxiliary  
Control Register. For more information see Auxiliary Control Registers on page 4-38.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
5-3  
     
PrefetchUnit  
5.2.2  
Branch predictor  
Branch prediction in the processor is dynamic and is based around a global history prediction  
scheme. In addition, there is extra logic to handle predictions that thrash and to predict the end  
of long loops.  
The global history scheme is an adaptive predictor that learns the behavior of branches during  
execution, based on the historical pattern of behavior of the preceding branches. For each  
pattern of branch behavior, the history table holds a 2-bit hint value. The 2-bit hint indicates if  
the next branch must be predicted taken or predicted not-taken based on the behavior of previous  
branches. The history table contains 256 entries.  
For loops beyond a certain number of iterations, the branch history is not large enough to learn  
the history and predict the loop exit. The PFU includes logic to count the number of iterations  
(up to 31) of a loop, and thereby predict the not-taken branch that exits the loop. If the number  
of iterations taken exceeds 31, the loop branch is never predicted as not-taken.  
If multiple branch histories index into the same hint value, this can cause thrashing in the history  
table and reduce accuracy of the branch predictor. Logic in the branch predictor detects these  
cases and provides some hysteresis for the hint value.  
For direct branches, the target address is calculated statically from the instruction encoding and  
the program counter. For indirect branches, the hint value predicts if the branch is taken or  
not-taken, and the return stack can sometimes be used to predict the target address. When the  
destination of a branch cannot be calculated statically, or popped from the return stack, PFU  
assumes the branch to be not-taken.  
The PFU updates the history for each occurrence of a branch when the DPU indicates how the  
branch was resolved.  
Configuring the branch predictor  
You can configure the branch predictor by setting bits in the Auxiliary Control Register:  
Set bits [16:15] to b00 to enable prediction using the pattern history tables.  
Set bits [16:15] to b01 to force branches to be always predicted taken.  
Set bits [16:15] to b10 to force branches to be always predicted not-taken.  
Set bit [21] to disable prediction using the dynamic branch predictor loop cache.  
Set bit [20] to disable prediction using the dynamic branch predictor register extension  
cache.  
Incorrect predictions and correction  
5.2.3  
The DPU resolves branches that the dynamic branch predictor predicts at the Wr-stage of the  
pipeline, see Figure 1-3 on page 1-17. A misprediction causes the PFU to flush the pipeline and  
fetch the correct instruction stream.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
5-4  
   
PrefetchUnit  
5.3  
Return stack  
The call-return stack predicts procedural returns that are program flow changes such as loads,  
and branch register. The dynamic branch predictor determines if conditional procedure returns  
are predicted as taken or not-taken. The return stack predicts the target address for unconditional  
procedure returns, and conditional procedure returns that have been predicted as taken by the  
branch predictor.  
The return stack consists of a 4-entry circular buffer. When the PFU detects a taken procedure  
call instruction, the PFU pushes the return address onto the return stack. The instructions that  
the PFU recognizes as procedure calls are:  
for ARM and Thumb instructions:  
BL immediate  
BLX immediate  
BLX Rm  
.
When the return stack detects a taken return instruction, the PFU issues an instruction fetch from  
the location at the top of the return stack, and pops the return stack. The instructions that the  
PFU recognizes as procedure returns are, in both the ARM and Thumb instruction sets:  
POP {..,pc}  
LDMIB Rn{!}, {..,pc}  
LDMDA Rn{!}, {..,pc}  
LDMDB Rn{!}, {..,pc}  
LDR pc, [sp], #4  
BX Rm  
.
Return stack mispredictions can exist when:  
The prediction that a conditional return passed or failed its condition code is not correct.  
The return address is not correct. The DPU resolves indirect branches that the return stack  
predicts at the Ret-stage of the pipeline, see Figure 1-3 on page 1-17. A misprediction  
causes the PFU to flush the pipeline and fetch the correct instruction stream.  
The return stack has no underflow or overflow detection. Either scenario is likely to cause a  
misprediction.  
Note  
The MOV PC, LRinstruction is not decoded and is not predicted as a return.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
5-5  
   
Chapter 6  
Events and Performance Monitor  
This chapter describes the Performance Monitoring Unit (PMU) and event bus interface. It  
contains the following sections:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
6-1  
   
Events and Performance Monitor  
6.1  
About the events  
The processor includes logic to detect various events that can occur, for example, a cache miss.  
These events provide useful information about the behavior of the processor that you can use  
when debugging or profiling code.  
The events are made visible on an output bus, EVNTBUS, and can be counted using registers  
in the Performance Monitoring Unit (PMU). See Event bus interface on page 6-19 for more  
information about the event bus, and About the PMU on page 6-6 for more information about  
the PMU. Table 6-1 lists the events that are generated, along with the bit position of each event  
on the event bus, and the numbers that the PMU uses to refer the events. Event reference  
numbers that are not listed are Reserved. See Error detection events on page 8-36 for more  
information on the CFLR related events.  
Table 6-1 Event bus interface bit functions  
Event  
CFLR  
EVNTBUS  
bit position  
Description  
Ref.  
update  
Value  
N/A  
[0]  
Software increment. The register is incremented only on writes to the  
Software Increment Register. See c9, Software Increment Register on  
-
0x00  
0x01  
Instruction cache miss.  
-
-
Each instruction fetch from normal Cacheable memory that causes a refill  
from the level 2 memory system generates this event. Accesses that do not  
cause a new cache refill, but are satisfied from refilling data of a previous miss  
are not counted. Where instruction fetches consist of multiple instructions,  
these accesses count as single events. CP15 cache maintenance operations do  
not count as events.  
[1]  
Data cache miss.  
0x03  
Each data read from or write to normal Cacheable memory that causes a refill  
from the level 2 memory system generates this event. Accesses that do not  
cause a new cache refill, but are satisfied from refilling data of a previous miss  
are not counted. Each access to a cache line to normal Cacheable memory that  
causes a new linefill is counted, including the multiple transactions of an LDM  
and STM. Write-through writes that hit in the cache do not cause a linefill and  
so are not counted. CP15 cache maintenance operations do not count as  
events.  
[2]  
Data cache access.  
-
0x04  
Each access to a cache line is counted including the multiple transactions of  
an LDM STM, or other operations. CP15 cache maintenance operations do not  
,
count as events.  
[3]  
[4]  
Data Read architecturally executed.  
-
-
0x06  
0x07  
This event occurs for every instruction that explicitly reads data, including  
SWP  
.
Data Write architecturally executed.  
This event occurs for every instruction that explicitly writes data, including  
SWP  
.
[5]  
[6]  
[7]  
Instruction architecturally executed.  
-
-
-
0x08  
0x5e  
0x09  
Dual-issued pair of instructions architecturally executed.  
Exception taken.  
This event occurs on each exception taken.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
6-2  
         
Events and Performance Monitor  
Table 6-1 Event bus interface bit functions (continued)  
Event  
CFLR  
update  
Value  
EVNTBUS  
bit position  
Description  
Ref.  
[8]  
Exception return architecturally executed.  
-
0x0A  
This event occurs on every exception return, for example, RFE MOVSPC, LDM  
,
PC^  
.
[9]  
Change to Context ID executed.  
Software change of PC, except by an exception, architecturally executed.  
immediate, BL immediate or BLXimmediate instruction architecturally  
-
-
-
0x0B  
0x0C  
0x0D  
[10]  
[11]  
B
executed (taken or not taken).  
[12]  
[13]  
Procedure return architecturally executed, other than exception returns, for  
-
-
0x0E  
0x0F  
example, BX Rm; LDM PC  
.
MOV PC, LRdoes not generate this event, because it is not predicted as a return.  
Unaligned access architecturally executed.  
This event occurs for each instruction that was to an unaligned address that  
either triggered an alignment fault, or would have done so if the System  
Control Register A-bit had been set.  
[14]  
Branch mispredicted or not predicted.  
-
0x10  
This event occurs for every pipeline flush caused by a branch.  
N/A  
[15]  
Cycle count.  
-
-
0x11  
0x12  
Branches or other change in program flow that could have been predicted by  
the branch prediction resources of the processor.  
[16]  
Stall because instruction buffer cannot deliver an instruction.  
-
0x40  
This can indicate an ICache miss. This event occurs every cycle where the  
condition is present.  
[17]  
[18]  
[19]  
Stall because of a data dependency between instructions.  
This event occurs every cycle where the condition is present.  
-
-
-
0x41  
0x42  
0x43  
Data cache write-back.  
This event occurs once for each line that is written back from the cache.  
External memory request.  
Examples of this are cache refill, Non-cacheable accesses, write-through  
writes, cache line evictions (write-back).  
[20]  
[21]  
Stall because of LSU being busy.  
-
-
0x44  
0x45  
This event takes place each clock cycle where the condition is met. A high  
incidence of this event indicates the pipeline is often waiting for transactions  
to complete on the external bus.  
Store buffer was forced to drain completely.  
Examples of this are DMB, Strongly Ordered memory access, or similar events.  
N/A  
N/A  
N/A  
N/A  
The number of cycles FIQ interrupts are disabled.  
The number of cycles IRQ interrupts are disabled.  
ETMEXTOUT[0].  
-
-
-
-
0x46  
0x47  
0x48  
0x49  
ETMEXTOUT[1].  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
6-3  
Events and Performance Monitor  
Table 6-1 Event bus interface bit functions (continued)  
Event  
CFLR  
update  
Value  
EVNTBUS  
bit position  
Description  
Ref.  
[22]  
[23]  
[24]  
[25]  
[26]  
[27]  
N/A  
N/A  
N/A  
N/A  
N/A  
N/A  
N/A  
N/A  
[28]  
Instruction cache tag RAM parity or ECC error (correctable).  
Instruction cache data RAM parity or ECC error (correctable).  
Data cache tag or dirty RAM parity error or correctable ECC error.  
Data cache data RAM parity error. or correctable ECC error  
TCM parity error or fatal ECC error reported from the prefetch unit.  
TCM parity error or fatal ECC error reported from the load/store unit.  
Store buffer merge.  
Yes  
0x4A  
0x4B  
0x4C  
0x4D  
0x4E  
0x4F  
0x50  
0x51  
0x52  
0x53  
0x54  
0x55  
0x56  
0x57  
0x58  
Yes  
Yes  
Yes  
-
-
-
-
-
-
-
-
-
-
-
LSU stall caused by full store buffer.  
LSU stall caused by store queue full.  
Integer divide instruction, SDIVor UDIV, executed.  
Stall cycle caused by integer divide.  
PLDinstruction that initiates a linefill.  
PLDinstruction that did not initiate a linefill because of a resource shortage.  
Non-cacheable access on AXI master bus.  
Instruction cache access.  
This is an analog to event 0x04  
.
N/A  
Store buffer operation has detected that two slots have data in same cache line  
but with different attributes.  
-
0x59  
[29]  
[30]  
[31]  
[32]  
[33]  
[34]  
[35]  
[36]  
[37]  
[38]  
[39]  
[40]  
[41]  
[42]  
Dual issue case A (branch).  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0x5A  
0x5B  
0x5C  
0x5D  
0x60  
0x61  
0x62  
0x63  
0x64  
0x65  
0x66  
0x67  
0x68  
0x69  
Dual issue case B1, B2, F2 (load/store), F2D.  
Dual issue other.  
Double precision floating point arithmetic or conversion instruction executed.  
Data cache data RAM fatal ECC error.  
Data cache tag/dirty RAM fatal ECC error.  
Processor livelock because of hard errors or exception at exception vector.a  
Unused.  
ATCM parity or multi-bit ECC error.  
B0TCM parity or multi-bit ECC error.  
B1TCM parity or multi-bit ECC error.  
ATCM single-bit ECC error.  
B0TCM single-bit ECC error.  
B1TCM single-bit ECC error.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
6-4  
Events and Performance Monitor  
Table 6-1 Event bus interface bit functions (continued)  
Event  
CFLR  
update  
Value  
EVNTBUS  
bit position  
Description  
Ref.  
[43]  
[44]  
[45]  
[46]  
N/A  
TCM correctable ECC error reported by load/store unit.  
TCM correctable ECC error reported by prefetch unit.  
TCM parity or fatal ECC error reported by AXI slave interface.  
TCM correctable ECC error reported by AXI slave interface.  
Cycle count  
Yes  
Yes  
-
0x6A  
0x6B  
0x6C  
0x6D  
0xFF  
Yes  
-
a. This event is only generated for by revisions r1p2 and later of the processor.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
6-5  
Events and Performance Monitor  
6.2  
About the PMU  
The PMU consists of three event counting registers, one cycle counting register and 12 CP15  
registers, for controlling and interrogating the counters. The performance monitoring registers  
are always accessible in Privileged mode. You can use the User Enable (USEREN) Register to  
make all of the performance monitoring registers, except for the USEREN, Interrupt Enable Set  
(INTENS), and Interrupt Enable Clear (INTENC) Registers, accessible in User mode.  
All three event counters are read and written through the same CP15 register. The Performance  
Counter Selection (PMNXSEL) Register determines which counter is read or written. The three  
Event Selection registers, one per counter, are read and written through one CP15 register in the  
same way.  
Using the control registers, you can enable or disable each of the event counters individually,  
and read and reset the overflow flag for each counter. Any or all of the counters can be enabled  
to assert an interrupt request output, nPMUIRQ, on overflow.  
When the processor is in Debug halt state:  
the PMU does not count events  
events are not visible on the ETM interface  
the Cycle CouNT (CCNT) register is halted.  
For more information on Debug state see Chapter 11 Debug.  
The PMU only counts events when non-invasive debug is enabled, that is, when either DBGEN  
or NIDEN inputs are asserted. The Cycle Count (CCNT) Register is always enabled regardless  
of whether non-invasive debug is enabled, unless the DP bit of the PMNC register is set. See c9,  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
6-6  
   
Events and Performance Monitor  
6.3  
Performance monitoring registers  
The performance monitoring registers are described in:  
6.3.1  
c9, Performance Monitor Control Register  
The Performance MoNitor Control (PMNC) Register controls the operation of the three count  
registers, and the CCNT Register.  
The PMNC Register is:  
A read/write register.  
Always accessible in Privileged mode. The USEREN Register determines accessibility in  
Figure 6-1 shows the bit arrangement for the PMNC Register.  
31  
24 23  
16 15  
11 10  
6
5
4
3
2
1
0
D
P
IMP  
IDCODE  
N
Reserved  
X D C P E  
Figure 6-1 PMNC Register format  
Table 6-2 shows how the bit values correspond with the PMNC Register.  
Table 6-2 PMNC Register bit functions  
Bits  
Field  
Function  
[31:24] IMP  
Implementer code:  
0x41= ARM  
[23:16] IDCODE Identification code:  
0x14= Cortex-R4  
[15:11]  
N
Specifies the number of counters implemented:  
0x3= three counters implemented  
[10: 6]  
[5]  
Reserved RAZ on reads, Should Be Zero or Preserved (SBZP) on writes  
DP  
Disable CCNT when prohibited, that is, when non-invasive debug is not enabled:  
0 = Count is enabled in prohibited regions. This is the reset value.  
1 = Count is disabled in prohibited regions.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
6-7  
               
Events and Performance Monitor  
Table 6-2 PMNC Register bit functions (continued)  
Bits  
Field  
Function  
[4]  
X
Enable export of the events to the event bus for an external monitoring block, for example the  
ETM, to trace events:  
0 = Export disabled. This is the reset value.  
1 = Export enabled.  
[3]  
[2]  
D
C
Cycle count divider:  
0 = Counts every processor clock cycle. This is the reset value.  
1 = Counts every 64th processor clock cycle.  
Cycle counter reset:  
0 = no action  
1 = reset cycle counter, CCNT, to zero.  
This bit Reads-As-Zero.  
[1]  
[0]  
P
E
Event counter reset:  
0 = no action  
1 = reset all event counters to zero.  
This bit Reads-As-Zero.  
Enable:  
0 = Disable all counters, including CCNT. This is the reset value.  
1 = Enable all counters including CCNT.  
The PMNC Register is always accessible in Privileged mode. To access the register, read or  
write CP15 with:  
MRC p15, 0, <Rd>, c9, c12, 0 ; Read PMNC Register  
MCR p15, 0, <Rd>, c9, c12, 0 ; Write PMNC Register  
6.3.2  
c9, Count Enable Set Register  
The CouNT ENable Set (CNTENS) Register enables any of the performance monitor count  
registers. When read, this register indicates which counters are enabled. Writing a 1 to a  
particular count enable bit enables that counter. Writing a 0 to a count enable bit has no effect.  
You must use the Count Enable Clear Register to disable the counters.  
The CNTENS Register is:  
A read/write register.  
Always accessible in Privileged mode. The USEREN Register determines accessibility in  
The values in this register are ignored unless the E bit, bit [0], is set in the PMNC Register, see  
Figure 6-2 on page 6-9 shows the bit arrangement for the CNTENS Register.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
6-8  
   
Events and Performance Monitor  
31  
C
3
2
1
0
Reserved  
Cycle count enable  
P2  
P1  
P0  
Performance monitor  
counter enables  
Figure 6-2 CNTENS Register format  
Table 6-3 shows how the bit values correspond with the CNTENS Register.  
Table 6-3 CNTENS Register bit functions  
Field Function  
Cycle counter enable set:  
Bits  
[31]  
C
0 = disable  
1 = enable.  
[30:3] Reserved UNP on reads, SBZP on writes  
[2]  
[1]  
[0]  
P2  
P1  
P0  
Counter 2 enable  
Counter 1 enable  
Counter 0 enable  
To access the CNTENS Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c9, c12, 1 ; Read CNTENS Register  
MCR p15, 0, <Rd>, c9, c12, 1 ; Write CNTENS Register  
The CNTENS Register retains its value when the enable bit of the PMNC is clear, even though  
its settings are ignored.  
6.3.3  
c9, Count Enable Clear Register  
The CouNT ENable Clear (CNTENC) Register disables any of the Performance Monitor Count  
Registers.  
When reading this register, any enable that reads as 0 indicates the corresponding counter is  
disabled. Any enable that reads as 1 indicates the corresponding counter is enabled.  
When writing this register, any enable written with a value of 0 is ignored, that is, not updated.  
Any enable written with a value of 1 clears the counter enable.  
The CNTENC Register is:  
A read/write register  
Always accessible in Privileged mode. The User Enable Register determines accessibility  
Figure 6-3 on page 6-10 shows the bit arrangement for the CNTENC Register.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
6-9  
           
Events and Performance Monitor  
31  
C
3
2
1
0
Reserved  
Cycle count disable  
P2  
P1  
P0  
Performance monitor  
counter disables  
Figure 6-3 CNTENC Register format  
Table 6-4 shows how the bit values correspond with the CNTENC Register.  
Table 6-4 CNTENC Register bit functions  
Field Function  
Cycle counter enable clear:  
Bits  
[31]  
C
0 = disable  
1 = enable.  
[30:3] Reserved UNP on reads, SBZP on writes  
[2]  
[1]  
[0]  
P2  
P1  
P0  
Counter 2 enable  
Counter 1 enable  
Counter 0 enable  
To access the CNTENC Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c9, c12, 2 ; Read CNTENC Register  
MCR p15, 0, <Rd>, c9, c12, 2 ; Write CNTENC Register  
Writing to bits in this register disables individual counters, and clears the corresponding bits in  
You can use the enable, EN, bit [0] of the PMNC Register to disable all performance counters  
The CNTENC and CNTENS Registers retain their values when the enable bit of the PMNC is  
clear, even though their settings are ignored. The CNTENC Register can be used to clear the  
enabled flags for individual counters even when all counters are disabled in the PMNC Register.  
6.3.4  
c9, Overflow Flag Status Register  
The overflow FLAG status (FLAG) Register indicates if performance monitor counters have  
overflowed.  
The FLAG Register is:  
A read/write register  
Always accessible in Privileged mode. The USEREN Register determines accessibility in  
Figure 6-4 on page 6-11 shows the bit arrangement for the FLAG Register.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
6-10  
           
Events and Performance Monitor  
31  
C
3
2
1
0
Reserved  
Cycle count overflow  
P2  
P1  
P0  
Performance monitor counters  
overflow flags  
Figure 6-4 FLAG Register format  
Table 6-5 shows how the bit values correspond with the FLAG Register.  
Table 6-5 Overflow Flag Status Register bit functions  
Field Function  
Bits  
[31]  
Cycle counter overflow Cycle counter overflow flag:  
0 = disable  
1 = enable.  
[30:3] Reserved  
UNP on reads, SBZP on writes  
Counter 2 overflow flag  
Counter 1 overflow flag  
Counter 0 overflow flag  
[2]  
[1]  
[0]  
P2  
P1  
P0  
To access the FLAG Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c9, c12, 3 ; Read FLAG Register  
MCR p15, 0, <Rd>, c9, c12, 3 ; Write FLAG Register  
If an overflow flag is set to 1 in the FLAG register it remains set until one of the following  
happens:  
writing 1 to the flag bit in the FLAG Register clears the flag  
the processor is reset.  
The following operations do not clear the overflow flags:  
disabling the overflowed counter in the CNTENC Register  
disabling all counters in the PMNC Register  
resetting the overflowed counter using the PMNC Register.  
6.3.5  
c9, Software Increment Register  
The Software INCRement (SWINCR) Register increments the count of a Performance Monitor  
Count Register.  
The SWINCR Register is:  
A write-only register that Reads-As-Zero  
Always accessible in Privileged mode. The USEREN Register determine accessibility in  
Caution  
You must only use the SWINCR Register to increment performance monitor count registers  
when the counter event is set to 0x00, software count, in the Event Select Register, see c9, Event  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
6-11  
           
Events and Performance Monitor  
If you attempt to use the SWINCR Register to increment a performance monitor count register  
when the counter event is set to a value other than 0x00the result is Unpredictable.  
Figure 6-5 shows the bit arrangement for the SWINCR Register.  
31  
3
2
1
0
Reserved  
P2  
P1  
P0  
Performance monitor counters  
software increment bits  
Figure 6-5 SWINCR Register format  
Table 6-6 shows how the bit values correspond with the SWINCR Register.  
Table 6-6 SWINCR Register bit functions  
Field Function  
[31:3] Reserved RAZ on reads, SBZP on writes  
Bits  
[2]  
[1]  
[0]  
P2  
P1  
P0  
Increment Counter 2  
Increment Counter 1  
Increment Counter 0  
To access the SWINCR Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c9, c12, 4 ; Read SWINCR Register  
MCR p15, 0, <Rd>, c9, c12, 4 ; Write SWINCR Register  
6.3.6  
c9, Performance Counter Selection Register  
The Performance Counter SELection (PMNXSEL) Register selects a Performance Monitor  
Count Register. It determines which count register is accessed or controlled by accesses to the  
Event Selection Register and the Performance Monitor Count Register.  
The PMNXSEL Register is:  
A read/write register  
Always accessible in Privileged mode. The USEREN Register determines accessibility in  
Figure 6-6 shows the bit arrangement for the PMNXSEL Register.  
31  
4
0
5
Reserved  
SEL  
Figure 6-6 PMNXSEL Register format  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
6-12  
               
Events and Performance Monitor  
Table 6-7 shows how the bit values correspond with the PMNXSEL Register functions.  
Table 6-7 Performance Counter Selection Register bit functions  
Bits  
Field  
Function  
[31:5] Reserved RAZ on reads, SBZP on writes  
[4:0]  
SEL  
Counter select:  
b00000 = selects counter 0  
b00001 = selects counter 1  
b00010 = selects counter 2.  
Any values programmed in the PMNXSEL Register other than those specified in Table 6-7 are  
Unpredictable.  
To access the PMNXSEL Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c9, c12, 5 ; Read PMNXSEL Register  
MCR p15, 0, <Rd>, c9, c12, 5 ; Write PMNXSEL Register  
6.3.7  
c9, Cycle Count Register  
The Cycle CouNT (CCNT) Register counts clock cycles.  
The CCNT Register is:  
A read/write register  
Always accessible in Privileged mode. The USEREN Register determines accessibility in  
To access the CCNT read or write CP15 with:  
MRC p15, 0, <Rd>, c9, c13, 0 ; Read CCNT Register  
MCR p15, 0, <Rd>, c9, c13, 0 ; Write CCNT Register  
The Cycle Count Register must be disabled before software can write to it. Any attempt by  
software to write to this register when enabled is Unpredictable.  
6.3.8  
c9, Event Selection Register  
There are three Event Selection Registers in the processor, EVTSEL0 to EVTSEL2, each  
corresponding to one of the Performance Monitor Count (PMC) Registers, PMC0 to PMC2.  
Each register selects the events you want a PMC Register to count. The register to be accessed  
is determined by the value in the Performance Counter Selection Register.  
The EVTSEL Register is:  
A read/write register  
Always accessible in Privileged mode. The USEREN Register determines accessibility in  
Figure 6-7 on page 6-14 shows the bit arrangement for the EVTSELx Register.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
6-13  
           
Events and Performance Monitor  
31  
8
7
0
Reserved  
SEL  
Figure 6-7 EVTSELx Register format  
Table 6-8 shows how the bit values correspond with the EVTSELx Register.  
Table 6-8 EVTSELx Register bit functions  
Bits  
Field  
Function  
[31:8] Reserved RAZ or SBZP.  
[7:0]  
SEL  
Event number selected, see Table 6-1 on page 6-2 for  
values.  
The reset value of this field is Unpredictable.  
To access the EVTSELx Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c9, c13, 1 ; Read EVTSELx Register  
MCR p15, 0, <Rd>, c9, c13, 1 ; Write EVTSELx Register  
The absolute counts of events recorded might vary because of pipeline effects. This has  
negligible effect except in cases where the counters are enabled for a very short time.  
In addition to the counters within the processor, most of the events that Table 6-1 on page 6-2  
shows are available to the ETM unit or other external trace hardware to enable monitoring of  
the events. For information on how to monitor these events, see the CoreSight ETM-R4  
Technical Reference Manual.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
6-14  
       
Events and Performance Monitor  
6.3.9  
c9, Performance Monitor Count Registers  
There are three PMC Registers (PMC0-PMC2) in the processor. Each PMC Register, as selected  
by the PMNXSEL Register, counts instances of an event selected by the EVTSEL Register. Bits  
[31:0] of each PMC Register contain an event count. The register to be accessed is determined  
by the value in the Performance Counter Selection Register.  
Each PMC Register is:  
A read/write register  
Always accessible in Privileged mode. The USEREN Register determines access, see c9,  
To access the current Performance Monitor Count Registers, read or write CP15 with:  
MRC p15, 0, <Rd>, c9, c13, 2 ; Read current PMNx Register  
MCR p15, 0, <Rd>, c9, c13, 2 ; Write current PMNx Register  
6.3.10 c9, User Enable Register  
The USER ENable (USEREN) Register enables User mode to have access to:  
the performance monitor registers, see Performance monitoring registers on page 6-7  
the validation registers, see Validation Registers on page 4-62.  
Note  
The USEREN Register does not provide access to the registers that control interrupt generation.  
The USEREN Register is:  
a read/write register  
writable only in Privileged mode, readable in any processor mode.  
Figure 6-8 shows the bit arrangement for the USEREN Register.  
31  
1
0
Reserved  
EN  
Figure 6-8 USEREN Register format  
Table 6-9 shows how the bit values correspond with the Performance Monitor Count Enable Set  
Register.  
Table 6-9 USEREN Register bit functions  
Bits  
Field  
Function  
[31:1] Reserved RAZ or SBZP.  
[0]  
EN  
User mode access to performance monitor and validation registers:  
0 = Disabled. This is the reset value.  
1 = Enabled.  
If the EN bit in the USEREN Register is not set, any attempt to access a performance monitor  
register or a validation register from User mode causes an Undefined instruction exception.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
6-15  
               
Events and Performance Monitor  
Note  
For more information on access permissions to the performance monitor registers and validation  
registers, see the ARM Architecture Reference Manual.  
To access the USEREN Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c9, c14, 0 ; Read USEREN Register  
MCR p15, 0, <Rd>, c9, c14, 0 ; Write USEREN Register  
6.3.11 c9, Interrupt Enable Set Register  
The INTerrupt ENable Set (INTENS) Register determines if any of the PMC Registers,  
PMC0-PMC2 and CCNT, generate an interrupt request on overflow.  
The INTENS Register is:  
a read/write register  
accessible in Privileged mode only.  
Reading this register returns the current setting. Writing to this register can enable interrupts.  
You can disable interrupts only by writing to the INTENC Register.  
Figure 6-9 shows the bit arrangement for the INTENS Register.  
31  
C
3
2
1
0
Reserved  
Cycle count overflow interrupt enable  
P2  
P1  
P0  
Performance monitor counter  
overflow interrupt enables  
Figure 6-9 INTENS Register format  
Table 6-10 shows how the bit values correspond with the INTENS Register.  
Table 6-10 INTENS Register bit functions  
Field Function  
CCNT overflow interrupt enable  
Bits  
[31]  
C
[30:3] Reserved UNP on reads, SBZP on write  
[2]  
[1]  
[0]  
P2  
P1  
P0  
PMC2 overflow interrupt enable  
PMC1 overflow interrupt enable  
PMC0 overflow interrupt enable  
When reading bits [31], [2], [1], and [0] of the INTENS Register:  
0 = interrupt disabled  
1 = interrupt enabled.  
When writing to bits [31], [2], [1], and [0] of the INTENS Register:  
0 = no action  
1 = interrupt enabled.  
To access the Interrupt Enable Set Register, read or write CP15 with:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
6-16  
           
Events and Performance Monitor  
MRC p15, 0, <Rd>, c9, c14, 1 ; Read INTENS Register  
MCR p15, 0, <Rd>, c9, c14, 1 ; Write INTENS Register  
If this unit generates an interrupt, the processor asserts the pin nPMUIRQ. You can route this  
pin to an external interrupt controller for prioritization and masking. This is the only mechanism  
that signals this interrupt to the processor.  
Note  
ARM expects that the Performance Monitor interrupt request signal, nPMUIRQ, connects to a  
system interrupt controller.  
6.3.12 c9, Interrupt Enable Clear Register  
The INTerrupt ENable Clear (INTENC) Register determines if any of the PMC Registers,  
PMC0-PMC2 and CCNT, generate an interrupt request on overflow.  
The INTENC Register is:  
a read/write register  
accessible in Privileged mode only.  
Reading this register returns the current setting. Writing to this register can disable interrupt  
requests. You can enable interrupt requests only by writing to the INTENS Register.  
Figure 6-10 shows the bit arrangement for the INTENC Register.  
31  
C
3
2
1
0
Reserved  
Cycle count overflow interrupt disable  
P2  
P1  
P0  
Performance monitor counter  
overflow interrupt disables  
Figure 6-10 INTENC Register format  
Table 6-11 shows how the bit values correspond with the INTENC Register.  
Table 6-11 INTENC Register bit functions  
Function  
CCNT overflow interrupt enable bit  
Bits  
Field  
[31]  
C
[30:3] Reserved UNP on reads, SBZP on writes  
[2]  
[1]  
[0]  
P2  
P1  
P0  
Interrupt on PMC2 overflow when enabled  
Interrupt on PMC1 overflow when enabled  
Interrupt on PMC0 overflow when enabled  
When reading bits [31], [2], [1], and [0] of the INTENC Register:  
0 = interrupt disabled  
1 = interrupt enabled.  
When writing to bits [31], [2], [1], and [0] of the INTENC Register:  
0 = no action  
1 = interrupt disabled.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
6-17  
           
Events and Performance Monitor  
To access the INTENC Register, read or write CP15 with:  
MRC p15, 0, <Rd>, c9, c14, 2 ; Read INTENC Register  
MCR p15, 0, <Rd>, c9, c14, 2 ; Write INTENC Register  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
6-18  
Events and Performance Monitor  
6.4  
Event bus interface  
The event bus, EVNTBUS, is used to signal when an event has occurred. The event bus includes  
most, but not all, of the events that can be counted by the performance monitoring unit. Each  
individual event is assigned to an individual bit of this bus, and this bit is asserted for one cycle  
each time the event occurs.  
The event bus only signals events when it is enabled. Set the X bit in the Performance Monitor  
Control Register to enable the event bus. See c9, Performance Monitor Control Register on  
See Table 6-1 on page 6-2 to see which bit of the event bus each event is signaled on.  
Note  
If an event is being counted in the PMU, the count might not be incremented in exactly the same  
cycle that the event is signaled on the event bus.  
6.4.1  
Use of the event bus and counters  
The event bus is designed to be connected to the ETM-R4, which enables processor events to  
trigger tracing for debug purposes. You can also connect it to event counting registers external  
to the processor, or to an interrupt generator.  
Because each EVNTBUS pin is only asserted for one cycle for each occurrence of the event, it  
is possible to create composite events by ORing various EVNTBUS pins together. A composite  
event signal like this is asserted when any of the included events occur although, if multiple  
events occur in the same cycle, the composite event only occurs once.  
The processor also has two event input pins, ETMEXTOUT[1:0]. This bus is normally  
intended for connection to the ETM, and enables the Cortex-R4 performance monitor to count  
events generated by the ETM. These inputs can alternatively be used for composite events  
generated external to the processor.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
6-19  
   
Chapter 7  
Memory Protection Unit  
This chapter describes the Memory Protection Unit (MPU). It contains the following sections:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
7-1  
   
Memory Protection Unit  
7.1  
About the MPU  
The MPU works with the L1 memory system to control accesses to and from L1 and external  
memory. For a full architectural description of the MPU, see the ARM Architecture Reference  
Manual.  
The MPU enables you to partition memory into regions and set individual protection attributes  
for each region. The MPU supports zero, eight, or twelve memory regions.  
Note  
If the MPU has zero regions, you cannot enable or program the MPU. Attributes are only  
determined from the default memory map when zero regions are implemented.  
Each region is programmed with a base address and size, and the regions can be overlapped to  
enable efficient programming of the memory map. To support overlapping, the regions are  
assigned priorities, with region 0 having the lowest priority and region 11 having the highest.  
The MPU returns access permissions and attributes for the highest priority region where the  
address hits.  
The MPU is programmed using CP15 registers c1 and c6, see MPU control and configuration  
on page 4-5. Memory region control read and write access is permitted only from Privileged  
modes.  
Table 7-1 shows the default memory map.  
Table 7-1 Default memory map  
Instruction memory type  
Data memory type  
Address  
range  
Execute Never  
Instruction  
cache enabled  
Instruction  
cache disabled  
Data cache  
enabled  
Data cache  
disabled  
0xFFFFFFFF  
0xF0000000  
Normal  
Normal  
Strongly Ordered  
Strongly  
Ordered  
Instruction  
execution only  
permitted if  
Non-cacheable  
only if HIVECS is  
TRUE  
Non-cacheable  
only if HIVECS is  
TRUE  
HIVECS is TRUE  
0xEFFFFFFF  
0xC0000000  
0xBFFFFFFF  
0xA0000000  
0x9FFFFFFF  
0x80000000  
0x7FFFFFFF  
0x60000000  
-
-
-
-
-
-
Strongly Ordered  
Shared Device  
Strongly  
Ordered  
Execute Never  
Execute Never  
Execute Never  
Instruction  
Shared  
Device  
Non-shared  
Device  
Non-shared  
Device  
Normal,  
Cacheable,  
Non-shared  
Normal,  
Non-cacheable,  
Non-shared  
Normal,  
Non-cacheable,  
Shared  
Normal,  
Non-cacheable, execution permitted  
Shared  
0x5FFFFFF  
Normal,  
Normal,  
Normal,  
Normal,  
Instruction  
Cacheable,  
Non-shared  
Non-cacheable,  
Non-shared  
WT Cacheable,  
Non-shared  
Non-cacheable, execution permitted  
Shared  
0x40000000  
0x3FFFFFFF  
0x00000000  
Normal,  
Cacheable,  
Non-shared  
Normal,  
Non-cacheable,  
Non-shared  
Normal,  
WBWA Cacheable  
, Non-shared  
Normal,  
Instruction  
Non-cacheable, execution permitted  
Shared  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
7-2  
       
Memory Protection Unit  
This section describes:  
7.1.1  
Memory regions  
Before the MPU is enabled, you must program at least one valid protection region. If you do not  
do this, the processor will enter a state that only reset can recover.  
When the MPU is disabled, no access permission checks are performed, and memory attributes  
are assigned according to the default memory map. See Table 7-1 on page 7-2.  
For more information on how to enable or disable the MPU, see MPU interaction with memory  
Depending on the implementation, the MPU has a maximum of eight or 12 regions. Using CP15  
register c6 you can specify the following for each region:  
region base address  
region size  
subregion enables  
region attributes  
region access permissions  
region enable.  
Region base address  
The base address defines the start of the memory region. You must align this to a region-sized  
boundary. For example, if a region size of 8KB is programmed for a given region, the base  
address must be a multiple of 8KB.  
Note  
If the region is not aligned correctly, this results in Unpredictable behavior.  
Region size  
The region size is specified as a 5-bit value, encoding a range of values from 32 bytes, a  
cache-line length, to 4GB. Table 4-32 on page 4-51 shows the encoding.  
Subregions  
Each region can be split into eight equal sized non-overlapping subregions. An access to a  
memory address in a disabled subregion does not use the attributes and permissions defined for  
that region. Instead, it uses the attributes and permissions of a lower priority region or generates  
a background fault if no other regions overlap at that address. This enables increased protection  
and memory attribute granularity.  
All region sizes between 256 bytes and 4GB support eight subregions. Region sizes below 256  
bytes do not support subregions, and the subregion disable field is SBZ/UNP for regions of less  
than 256 bytes in size.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
7-3  
   
Memory Protection Unit  
Region attributes  
Each region has a number of attributes associated with it. These control how a memory access  
is performed when the processor accesses an address that falls within a given region. The  
attributes are:  
Memory Type, one of:  
Strongly Ordered  
Device  
Normal  
Shared or Non-shared  
Non-cacheable  
Write-through Cacheable  
Write-back Cacheable  
Read allocation  
Write allocation.  
See Memory types on page 7-7 for more information about memory types, and Region attributes  
on page 7-9 for a description of how to assign types and attributes to a region.  
Region access permissions  
Each region can be given no access, read-only access, or read/write access permissions for  
Privileged or all modes. In addition, each region can be marked as eXecute Never (XN) to  
prevent instructions being fetched from that region.  
For example, if a User mode application attempts to access a Privileged mode access only region  
a permission fault occurs.  
The ARM architecture uses constants known as inline literals to perform address calculations.  
The assembler and compiler automatically generate these constants and they are stored inline  
with the instruction code. To ensure correct operation, only a memory region that has permission  
for data read access can execute instructions. For more information, see the ARM Architecture  
Reference Manual. For information about how to program access permissions, see Table 4-34  
Instructions cannot be executed from regions with Device or Strongly-Ordered memory type  
attributes. The processor treats such regions as if they have XN permissions.  
7.1.2  
Overlapping regions  
You can program the MPU with two or more overlapping regions. For overlapping regions, a  
fixed priority scheme determines attributes and permissions for memory access to the  
overlapping region. Attributes and permissions for region 11 take highest priority, those for  
region 0 take lowest priority. For example:  
Region 2  
Is 4KB in size, starting from address 0x3000. Privileged mode has full  
access, and User mode has read-only access.  
Region 1  
Is 16KB in size, starting from address 0x0000. Both Privileged and User  
modes have full access.  
When the processor performs a data write to address 0x3010while in User mode, the address  
falls into both region 1 and region 2, as Figure 7-1 on page 7-5 shows. Because these regions  
have different permissions, the permissions associated with region 2 are applied. Because User  
mode is read access only for this region, a permission fault occurs, causing a data abort.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
7-4  
   
Memory Protection Unit  
Region 2  
0x4000  
0x3000  
0x3010  
Region 1  
0x0000  
Figure 7-1 Overlapping memory regions  
Example of using regions that overlap  
You can use overlapping regions for stack protection. For example:  
allocate to region 1 the appropriate size for all stacks  
allocate to region 2 the minimum region size, 32 bytes, and position it at the end of the  
stack for the current process  
set the region 2 access permissions to No Access.  
If the current process overflows the stack it uses, a write access to region 2 by the processor  
causes the MPU to raise a permission fault.  
0x4000  
Region 1  
Region 2  
0x0000  
Figure 7-2 Overlay for stack protection  
Example of using subregions  
You can use subregions for stack protection. For example:  
Allocate to region 1 the appropriate size for all stacks.  
Set the least-significant subregion disable bit. That is, set the subregion disable field, bits  
[15:8], of the CP15 MPU Region Size Register to 0x01  
.
If the current process overflows the stack it uses, a write access by the processor to the disabled  
subregion causes the MPU to raise a background fault.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
7-5  
     
Memory Protection Unit  
0x4000  
Stack  
0x0800  
0x0000  
Guard region  
Figure 7-3 Overlapping subregion of memory  
7.1.3  
Background regions  
Overlapping regions increase the flexibility of how the regions can be mapped onto physical  
memory devices in the system. You can also use the overlapping properties to specify a  
background region. For example, you might have a number of physical memory areas sparsely  
distributed across the 4GB address space. If a programming error occurs, the processor might  
issue an address that does not fall into any defined region.  
If the address that the processor issues falls outside any of the defined regions, the MPU is  
hard-wired to abort the access. That is, all accesses for an address that is not mapped to a region  
in the MPU generate a background fault. You can override this behavior by programming region  
0 as a 4GB background region. In this way, if the address does not fall into any of the other 11  
regions, the attributes and access permissions you specified for region 0 control the access.  
In Privileged modes, you can also override this behavior by setting the BR bit, bit [17], of the  
System Control Register. This causes Privileged accesses that fall outside any of the defined  
regions to use the default memory map.  
7.1.4  
TCM regions  
Any memory address that you configure to be accessed using a TCM interface is given Normal,  
Non-shared type attributes, regardless of the attributes of any MPU region that the address also  
belongs to. Access permissions for an address in a TCM region are preserved from the MPU  
region that the address also belongs to. For more information, see About the TCMs on page 8-13.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
7-6  
     
Memory Protection Unit  
7.2  
Memory types  
The ARM Architecture defines a set of memory types with characteristics that are suited to  
particular devices. There are three mutually exclusive memory type attributes:  
Strongly Ordered  
Device  
Normal.  
MPU memory regions can each be assigned a memory type attribute. Table 7-2 shows a  
summary of the memory types.  
Table 7-2 Memory attributes summary  
Memory  
type  
attribute  
Shared or  
Non-shared  
Other attributes  
Description  
Strongly  
Ordered  
-
-
All memory accesses to Strongly Ordered memory occur in  
program order. All Strongly Ordered accesses are assumed to  
be shared.  
Device  
Normal  
Shared  
-
-
For memory-mapped peripherals that several processors share.  
Non-shared  
For memory-mapped peripherals that only a single processor  
uses.  
Shared  
Non-cacheable  
For normal memory that is shared between several processors.  
Write-throughCacheable  
Write-back Cacheable  
Non-shared  
Non-cacheable  
For normal memory that only a single processor uses.  
Write-throughCacheable  
Write-back Cacheable  
Note  
The processor’s L1 cache does not cache shared normal regions.  
For more information on memory attributes and types, memory barriers, and ordering  
requirements for memory accesses, see the ARM Architecture Reference Manual and  
Application Note 204, Understanding processor memory types and access ordering.  
7.2.1  
Using memory types  
The processor's memory system contains a store buffer which helps to improve the throughput  
of accesses to Normal type memory. See Store buffer on page 8-18 for more information.  
Because of the ordering rules which they must follow, accesses to other types of memory  
typically have a lower throughput or higher latency than accesses to Normal memory. In  
particular:  
reads from Device memory must first drain the store buffer of all writes to Device memory  
all accesses to Strongly Ordered memory must first drain the store buffer completely.  
Similarly, when it is accessing Strongly Ordered or Device type memory, the processor's  
response to interrupts must be modified, and the interrupt response latency is longer. See Low  
interrupt latency on page 2-19 for more information.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
7-7  
         
Memory Protection Unit  
To ensure optimum performance, you must understand the architectural semantics of the  
different memory types. Use Device memory type for appropriate memory regions, typically  
peripherals, and only use Strongly Ordered memory type for memory regions where it is  
essential.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
7-8  
Memory Protection Unit  
7.3  
Region attributes  
Each region has a number of attributes associated with it. These control how a memory access  
is performed when the processor accesses an address that falls within a given region. The  
attributes are:  
Strongly Ordered  
Device  
Normal  
Shared or Non-shared  
Non-cacheable  
Write-through cacheable  
Write-back cacheable  
Read allocation  
Write allocation.  
The Region Access Control Registers use five bits to encode the memory region type. These are  
the TEX)[2:0], C and B bits. Table 7-3 shows the mapping of these bits to memory region  
attributes.  
Note  
In earlier versions of the architecture, the TEX, C, and B bits were known as the Type Extension,  
Cacheable and Bufferable bits. These names no longer adequately describe the function of the  
B, C, and TEX bits.  
All memory attributes which are Cacheable, write-back or write-through, are also implicitly  
read-allocate. Table 7-3 shows which attributes are write-allocate.  
In addition, the Region Access Control Registers contain the shared bit, S. This bit only applies  
to Normal memory, and determines whether the memory region is Shared (1) or Non-shared (0).  
Table 7-3 TEX[2:0], C, and B encodings  
TEX[2:0]  
C
B
Description  
Memory Type  
Shareable?  
000  
000  
000  
000  
001  
001  
001  
001  
010  
010  
0
0
1
1
0
0
1
1
0
0
0
1
0
1
0
1
0
1
0
1
Strongly-ordered.  
Strongly-ordered Shareable  
Shareable Device.  
Device  
Normal  
Normal  
Normal  
-
Shareable  
S bita  
S bita  
S bita  
-
Outer and Inner write-through, no write-allocate.  
Outer and Inner write-back, no write-allocate.  
Outer and Inner Non-cacheable.  
Reserved.  
S bita  
Outer and Inner write-back, write-allocate.  
Non-shareable Device.  
Normal  
Device  
-
Non-shareable  
-
Reserved.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
7-9  
           
Memory Protection Unit  
Table 7-3 TEX[2:0], C, and B encodings (continued)  
TEX[2:0]  
C
B
Description  
Memory Type  
Shareable?  
010  
011  
1BB  
1
X
X
A
Reserved.  
-
-
X
A
Reserved.  
-
-
AAb = Inner policy  
BBb = Outer policy  
S bita  
Cacheable memory:  
Normal  
a. Region is Shareable if S == 1, and Non-shareable if S == 0.  
b. Table 7-4 shows the encoding for these bits.  
7.3.1  
Cacheable memory policies  
When TEX[2] == 1, the memory region is Cacheable memory, and the rest of the encoding  
defines the Inner and Outer cache policies:  
TEX[1:0]  
C,B  
defines the Outer cache policy  
defines the Inner cache policy  
The same encoding is used for the Outer and Inner cache policies. Table 7-4 shows the  
encoding.  
Table 7-4 Inner and Outer cache policy encoding  
Memory attribute encoding Cache policy  
00  
01  
10  
11  
Non-cacheable  
Write-back, write-allocate  
Write-through, no write-allocate  
Write-back, no write-allocate  
When the processor performs a memory access through its AXI bus master interface:  
the Inner attributes are indicated on the A*USERM signals. For the encodings, see  
the Outer attributes are indicated on the and A*CACHEM signals. For the encodings, see  
For more information on region attributes, see the ARM Architecture Reference Manual.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
7-10  
     
Memory Protection Unit  
7.4  
MPU interaction with memory system  
This section describes how to enable and disable the MPU. After you enable or disable the  
MPU, the pipeline must be flushed using ISBand DSBinstructions to ensure that all subsequent  
instruction fetches see the effect of turning on or off the MPU.  
Before you enable or disable the MPU you must:  
1.  
Program all relevant CP15 registers. This includes setting up at least one memory region  
that covers the currently executing code, and that the attributes and permissions of that  
region are the same as the attributes and permissions of the region in the default memory  
map that covers the code, and that the region is executable in Privileged mode.  
2.  
3.  
4.  
Clean and invalidate the data caches.  
Disable caches.  
Invalidate the instruction cache.  
The following code is an example of enabling the MPU:  
MRC p15, 0, R1, c1, c0, 0  
; read CP15 register 1  
ORR R1, R1, #0x1  
DSB  
MCR p15, 0, R1, c1, c0, 0  
ISB  
; enable MPU  
Fetch from programmed memory map  
Fetch from programmed memory map  
Fetch from programmed memory map  
Fetch from programmed memory map  
The following code is an example of disabling the MPU:  
MRC p15, 0, R1, c1, c0, 0  
BIC R1, R1, #0x1  
; read CP15 register 1  
DSB  
MCR p15, 0, R1, c1, c0, 0  
ISB  
; disable MPU  
Fetch from default memory map  
Fetch from default memory map  
Fetch from default memory map  
Fetch from default memory map  
Table 7-1 on page 7-2 shows the default memory map.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
7-11  
   
Memory Protection Unit  
7.5  
MPU faults  
The MPU can generate three types of fault:  
When a fault occurs, the memory access or instruction fetch is precisely aborted, and a prefetch  
abort or data abort exception is taken as appropriate. No memory accesses are performed on the  
AXI bus master interface. For more information about fault handling, see Fault handling on  
7.5.1  
Background fault  
A background fault is generated when the MPU is enabled and a memory access is made to an  
address that is not within an enabled subregion of an MPU region. A background fault does not  
occur if the background region is enabled and the access is Privileged. See Background regions  
7.5.2  
7.5.3  
Permission fault  
A permission fault is generated when a memory access does not meet the requirements of the  
permissions defined for the memory region that it accesses. See Region access permissions on  
Alignment fault  
An alignment fault is generated if a data access is performed to an address that is not aligned for  
the size of the access, and strict alignment is required for the access. A number of instructions  
that access memory, for example, LDMand STC, require strict alignment. See the ARM  
Architecture Reference Manual for details. In addition, strict alignment can be required for all  
data accesses by setting the A-bit in the System Control Register. See c1, System Control  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
7-12  
         
Memory Protection Unit  
7.6  
MPU software-accessible registers  
Figure 4-2 on page 4-5 shows the CP15 registers that control the MPU.  
read as zero and ignore writes in Privileged mode. No Undefined instruction exceptions are  
taken.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
7-13  
   
Chapter 8  
Level One Memory System  
This chapter describes the processor Level one (L1) memory system. It contains the following  
sections:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-1  
   
Level One Memory System  
8.1  
About the L1 memory system  
The processor L1 memory system can be configured during implementation and integration. It  
can consist of:  
separate instruction and data caches  
multiple Tightly-Coupled Memory (TCM) areas  
a Memory Protection Unit (MPU).  
The instruction-side and data-side can each optionally have their own L1 caches. The cache  
architecture is Harvard, that is, only instructions can be fetched from the i-cache, and only data  
can be fetched from the d-cache. In parallel with each of the caches are two areas of dedicated  
RAM accessible to both the instruction and data sides. These are regions of TCM. You can  
implement one TCM using the ATCM interface and up to two TCMs using the BTCM interface.  
Each TCM and cache can be configured at implementation time to have an error detection and  
correction scheme to protect the data stored in the memory from errors. Each TCM interface  
also has support for logic external to the processor to tell the processor that an error has  
occurred.  
The MPU handles accesses to both the instruction and data sides. The MPU is responsible for  
protection checking, address access permissions, and memory attributes. Some of these  
functions can be passed to the L2 memory system through the AXI master. See Chapter 7  
Memory Protection Unit for more information about the MPU.  
The L1 memory system includes a monitor for exclusive accesses. Exclusive load and store  
instructions can be used, for example, LDREX STREX, with the appropriate memory monitoring to  
,
provide inter-process or inter-processor synchronization and semaphores. See the ARM  
Architecture Reference Manual for more details. The monitor can handle some exclusive  
monitoring internally to the processor.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-2  
   
Level One Memory System  
AXI bus  
Processor  
AXI master  
External Tightly-Coupled Memory (TCM)  
Data cache  
controller and  
RAMs  
Instruction cache  
controller and  
RAMs  
B0TCM  
B1TCM  
ATCM  
Interconnect  
Memory  
Protection Unit  
(MPU)  
Prefetch Unit  
(PFU)  
Load Store Unit  
(LSU)  
AXI slave  
AXI bus  
Data Processing Unit (DPU)  
Figure 8-1 L1 memory system block diagram  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-3  
   
Level One Memory System  
8.2  
About the error detection and correction schemes  
In silicon devices, stray radiation and other effects can cause the data stored in a RAM to be  
corrupted. The TCMs and caches on Cortex-R4 can be configured to detect and correct errors  
that can occur in the RAMs. Extra, redundant data is computed by the processor and stored in  
the RAMs alongside the real data. When the processor reads data from the RAMs, it checks that  
the redundant data is consistent with the real data and can either signal an error, or attempt to  
correct the error.  
A number of different error schemes are available, and are described in:  
Each has different properties in terms of the number of errors that can be detected, and corrected,  
and the amount of extra RAM required to store the redundant data. Because different logic is  
required for each scheme, the scheme must be chosen in the build-configuration, although you  
can enable or disable, or change the behavior of the error schemes using software-configuration.  
This section describes the generic properties of each of the schemes. See Appendix B ECC  
Schemes for more information about the advantages and disadvantages of each scheme to the  
implementer. The details of operation of the error schemes for the caches are described in Cache  
The error schemes are each described in terms of their operation on a doubleword (64 bits) of  
data, because this is the amount of data that the processor L1 memory system can transfer each  
cycle. The tag and dirty RAMs associated with the caches are different sizes, but the principles  
are the same. An error is considered to be a single bit of data that has been inverted relative to  
its correct value.  
Figure 8-2 shows the error schemes. The shaded areas represent bits with errors.  
Parity: one error per  
byte detected  
64-bit ECC: one error  
per doubleword  
corrected  
64-bit ECC: two errors  
per doubleword  
detected  
32-bit ECC: one error  
per word corrected  
32-bit ECC: two errors  
per word detected  
Figure 8-2 Error detection and correction schemes  
8.2.1  
Parity  
For each byte, a parity bit is computed and stored with that byte. This requires eight bits of  
parity, or redundant data per doubleword. With a parity scheme, a single error in a byte or its  
parity bit can be detected, but not corrected. This means that, provided they are all in different  
bytes, eight errors can be detected per doubleword. However, if there are two errors in any  
individual byte, this cannot be detected. Odd or even parity can be used, and this can be  
pin-configured during integration.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-4  
         
Level One Memory System  
8.2.2  
Error checking and correction  
The processor supports Error Checking and Correction (ECC) schemes for either 64-bits or  
32-bits of data, and these have similar properties, although though the size of the data chunk that  
the ECC scheme applies to is different. For each data chunk, either 32-bits or 64-bits, aligned,  
a number of redundant code bits are computed and stored with the data. This enables the  
processor to detect up to two errors in the data chunk or its code bits, and correct any single error  
in the data chunk or its associated code bits. This is sometimes referred to as a  
Single-Error-Correction, Double-Error-Detection (SEC-DED) ECC scheme.  
If there are more than two errors in a data chunk and its associated code bits, they might or might  
not be detected. The error scheme might interpret such a condition as a single-error and make  
an unsuccessful attempt at a correction.  
64-bit ECC  
Eight code bits are computed for each 64 bits of data. The scheme can correct any single error  
occurring in any doubleword, and detect any two errors occurring in any doubleword.  
32-bit ECC  
Seven code bits are computed for each 32 bits of data, so 14 bits of redundant data are required  
for each doubleword. The scheme can correct two errors per doubleword, if they are in different  
words. Four errors can be detected per doubleword, if there are two in each word.  
8.2.3  
Read-Modify-Write  
The smallest unit of data that the processor can write is a byte. However, both the ECC schemes  
are computed on data chucks that are larger than this. To write any data to a RAM protected with  
ECC requires the error code for that data to be recomputed and rewritten. If the entire data chunk  
is not written, for example, a halfword, 16-bits, is written to address 0x4of a RAM with a 32-bit  
error scheme, the error code must be computed partly from the data being written, and partly  
from data already stored in the RAM. In this example, the halfword in the RAM at address 0x6  
.
To compute the error code for such a write, the processor must first read data from the RAM,  
then merge the data to be written with it, to compute the error code, then write the data to the  
RAM, along with the new error code. This process is referred to as read-modify-write.  
8.2.4  
Hard errors  
The errors described in this chapter are all assumed to be soft errors, that is, one or more bits of  
the data stored in a RAM chunk are inverted. A new value can still be written to the RAM and  
read back correctly, unless another soft error occurs in the meantime.  
If the error in the memory is a hard error, that is, a physical failure of the RAM circuit so that a  
bit can never be read or written reliably, the processor might not be able to correct and recover  
from the error. The processor contains features that enable it to recover from some hard errors.  
If you are implementing the processor and require these features, contact ARM to discuss the  
features and your requirements.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-5  
       
Level One Memory System  
8.2.5  
Error correction  
When a correctable error is detected in data that has been read from a RAM, the processor has  
various ways of generating the correct data, which follow two schemes:  
Correct inline  
The error code bits are used to correct the data read from the RAM, and this data  
is used. This is the simplest way of correcting the data.  
Correct-and-retry  
The error code bits are used to correct the data, and this data is then written back  
to the RAM. The processor then repeats the read access by re-executing the  
instruction that caused the read, and reads the corrected data from the RAM if no  
more errors have occurred. This takes more clock cycles (at least nine) in the  
event of an error, but has the side-effect of correcting the data in the RAM so that  
the errors in the data cannot become worse.  
Note  
Because RAM errors generally occur infrequently, the extra cycles required to  
perform correct-and-retry do not have a significant impact on average  
performance.  
The correction method that the processor uses depends on the individual error. The processor  
uses correct inline error correction when it detects a correctable error on a TCM read made by  
the AXI-slave interface. The processor uses correct-and-retry correction when it detects a  
correctable ECC error on a TCM read made by the instruction-side or data-side.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-6  
Level One Memory System  
8.3  
Fault handling  
Faults can occur on instruction fetches for the following reasons:  
MPU background fault  
MPU permission fault  
External AXI slave error (SLVERR)  
External AXI decode error (DECERR)  
Cache parity or ECC error  
TCM parity or ECC error  
TCM external error  
TCM external retry request  
Breakpoints, and vector capture events.  
Faults can occur on data accesses for the following reasons:  
MPU background fault  
MPU permission fault  
MPU alignment fault  
External AXI slave error (SLVERR)  
External AXI decode error (DECERR)  
Cache parity or ECC error  
TCM parity or ECC error  
TCM external error  
TCM external retry request  
Watchpoints.  
Fault handling is described in:  
8.3.1  
Faults  
The classes of fault that can occur are:  
MPU faults  
The MPU can generate an abort for various reasons. See MPU faults on page 7-12 for more  
details. MPU faults are always precise, and take priority over other types of abort. If an MPU  
fault occurs on an access that is not in the TCM, and is Non-cacheable, or has generated a  
cache-miss, the AXI transactions for that access is not performed.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-7  
       
Level One Memory System  
External faults  
A memory access performed through the AXI master interface can generate two different types  
of error response, a slave error (SLVERR) or decode error (DECERR). These are known as  
external errors, because they are generated by the AXI system outside the processor. Precise  
aborts are generated for instruction fetches, data loads, and data stores to strongly-ordered-type  
memory. Stores to normal-type or device-type memory generate imprecise aborts.  
Note  
An AXI slave that cannot handle exclusive transactions returns OKAY in response to an  
exclusive read. This is also treated as an external error, and the processor behaves as if the  
response was SLVERR.  
Cache and TCM parity and ECC errors  
If the processor has been configured with the appropriate build options, it can detect data errors  
occurring in the cache and TCM RAMs using parity or ECC logic. For more information on  
configuration of the processor, these errors are either ignored, generate an abort, are  
automatically corrected without generating an abort, or are corrected and generate an abort. If  
the processor is in debug-halt-state, an error that is otherwise automatically corrected generates  
an abort.  
Parity and ECC errors can only occur on reads, although these reads might be a side-effect of  
store instructions. Aborts generated by loads are always precise. Aborts generated by store  
instructions to the TCM are also always precise, while those to the cache are always imprecise.  
These errors can also occur on some cache-maintenance operations, see Errors on cache  
Many of the parity and ECC errors are also signaled by the generation of events. See Chapter 6  
Events and Performance Monitor. Some of these events are generated when the error is  
detected, regardless of whether or not an abort is taken. Aborts are only taken when a memory  
access with an error is committed. Others are signaled when and only when the abort is taken.  
Any parity or ECC error that can be corrected by the processor is considered to be a correctable  
fault, regardless of whether or not the processor is configured to correct the fault.  
TCM external faults  
The TCM port includes signals that can be used to signal an error on a TCM transaction. See the  
Cortex-R4 and Cortex-R4F Integration Manual for more information about the TCM port. If  
enabled, this causes the processor to take the appropriate type of abort for instruction and data  
accesses, or to generate a SLVERR response to an AXI-slave transaction. Write transactions  
always generate imprecise aborts, while read transactions always generate precise aborts.  
An error signaled on a read transaction can also signal a retry request, which requests that the  
processor retry the same operation rather than take an exception.  
A retry request from the TCM port is considered to be a recoverable error. All correctable ECC  
faults are also considered to be recoverable.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-8  
     
Level One Memory System  
Debug events  
The debug logic in the processor can be configured to generate breakpoints or vector capture  
events on instruction fetches, and watchpoints on data accesses. If the processor is  
software-configured for monitor-mode debugging, an abort is taken when one of these events  
occurs, or when a BKPTinstruction is executed. For more details, see Chapter 11 Debug.  
Precise and imprecise aborts  
See Aborts on page 2-22 for more information about the differences between precise and  
imprecise aborts.  
8.3.2  
Fault status information  
When an abort occurs, information about the cause of the fault is recorded in a number of  
registers, depending on the type of abort:  
Abort exceptions  
The following registers are updated when any abort exception is taken:  
Link Register  
The r14_abt register is updated to provide information about the address of the  
instruction that the exception was taken on, in a similar way to other types of  
exception. See Exceptions on page 2-16 for more details. This information can be  
used to resume program execution after the abort has been handled.  
Note  
When a prefetch abort has occurred, ARM recommends that you do not use the  
link register value for determining the aborting address, because 32-bit Thumb  
instructions do not have to be word aligned and can cause an abort on either  
halfword. This applies even if all of the code in the system does not use the extra  
32-bit Thumb instructions introduced in ARMv6T2, because the earlier BLand  
BLXinstructions are both 32 bits long. Use the Fault Address Register instead, as  
described in this section.  
Saved Program Status Register  
The SPSR_abt register is updated to record the state and mode of the processor  
when the exception was taken, in a similar way to other types of exception. See  
Fault Status Register  
There are two fault status registers, one for prefetch aborts (IFSR) and one for  
data aborts (DFSR). These record the type of abort that occurred, and whether it  
occurred on a read or a write. In particular, this enables the abort handler to  
distinguish between precise aborts, imprecise aborts, and debug events. For  
details of the format of this register and the encodings used, see Fault Status and  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-9  
       
Level One Memory System  
Precise abort exceptions  
The following registers are updated when a precise abort exception is taken:  
Fault Address Register  
There are two fault address registers, one for prefetch aborts (IFAR) and one for  
data aborts (DFAR). These indicate the address of the memory access that caused  
Auxiliary Fault Status Register  
There are two auxiliary fault status registers, one for prefetch aborts (AIFSR) and  
one for data aborts (ADFSR). These record additional information about the  
nature and location of the fault, including whether it was a recoverable error or  
not, whether it occurred in the cache or AXI-master interface, ATCM or BTCM  
and, if appropriate, which cache way the error occurred in. The cache index is not  
recorded on a precise abort, because this information can be derived from the fault  
Imprecise abort exceptions  
The following register is updated when an imprecise abort exception is taken:  
Auxiliary Data Fault Status Register  
The ADFSR is updated to indicate whether or not the fault was recoverable,  
whether it occurred in the cache, ATCM or BTCM and, if appropriate, which  
cache set and way the error occurred in. Because the DFAR is not updated on  
imprecise aborts, imprecise aborts cannot normally be located, except when the  
error occurred in the cache.  
The effect of debug events on these registers is described in Debug exception on page 11-41.  
8.3.3  
Correctable Fault Location Register  
When a correctable fault generates an abort exception, information about the location of that  
fault is recorded in the various fault status registers. However, if the fault is automatically  
corrected by the processor, depending on the configuration, an exception might not be  
generated, and the fault status registers might not be not updated. In all cases, information about  
the location of the fault is recorded in the Correctable Fault Location Register (CFLR).  
All correctable faults are recorded in the same register, regardless of whether it was an  
instruction-fetch, a data-access, or a DMA (AXI-slave) access that generated the fault, and  
whether the fault occurred in the ATCM, BTCM or cache. The CFLR contains information to  
identify what sort of access generated the fault, and which device it occurred in. See Correctable  
Fault Location Register on page 4-70 for more details of the format of this register. Each time  
the CFLR is updated, the information already in the CFLR is discarded and therefore the CFLR  
can only contain information about the most recent correctable fault.  
8.3.4  
Usage models  
This section describes some ways in which errors can be handled in a system. Exactly how you  
program the processor to handle errors depends on the configuration of your processor and  
system, and what you are trying to achieve.  
If an abort exception is taken, the abort handler reads the information in the link register, SPSR,  
and fault status registers to determine the type of abort. Some types of abort are fatal to the  
system, and others can be fixed, and program execution resumed. For example, an MPU  
background fault might indicate a stack overflow, and be rectified by allocating more stack and  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-10  
       
Level One Memory System  
reprogramming the MPU to reflect this. Alternatively, an imprecise external abort might  
indicate that a software error meant that a store instruction occurred to an unmapped memory  
address. Such an abort is fatal to the system or process because no information is recorded about  
the address the error occurred on, or the instruction which caused the error.  
Table 8-1 shows which types of abort are typically fatal because either the location of the error  
is not recorded or the error is unrecoverable. Some aborts that are marked as not fatal might turn  
out to be fatal in some systems when the cause of the error has been determined. For example,  
an MPU background fault might indicate a stack overflow, which can be rectified, or it might  
indicate that, because of a bug, the software has accessed a nonexistent memory location, which  
can be fatal. These cases can be distinguished by determining the location where the error  
occurred. If an error is unrecoverable, that is, it is not a correctable parity or ECC error, and it  
is not a TCM external retry request, it is normally fatal regardless of whether or not the location  
of the error is recorded. When an abort is taken on an external TCM, parity, or ECC error, the  
appropriate Auxiliary Fault Status Register records whether the error was recoverable. See Fault  
Table 8-1 Types of aborts  
Type  
Conditions  
Source Precise Fatal  
Access not permitted by MPUa  
Load using L2 memory interface  
MPU fault  
MPU  
AXI  
AXI  
Yes  
Yes  
No  
No  
No  
Yes  
Precise External  
Imprecise External  
Store to Normal or Device memory using L2 memory  
interface  
Load from cacheb  
Maybec  
Maybec  
Yes  
Precise Parity/ECC Cache  
Precise Parity/ECC TCM  
Precise TCM external error  
Imprecise Parity/ECC Cache  
Cache  
TCM  
TCM  
Cache  
TCM  
Yes  
Yes  
Yes  
No  
Load/store from/to TCMd  
Load/store from/to TCMe  
Store to cache or cache maintenance operationb  
Store to TCMe  
Maybec  
Yes  
Imprecise TCM external  
error  
No  
a. See MPU faults on page 7-12 for more information about the types of MPU fault.  
b. See Cache error detection and correction on page 8-20 for more information about parity/ECC errors from the cache.  
c. These types of error can be correctable or uncorrectable. Uncorrectable errors are typically fatal. Correctable errors are  
automatically corrected by the hardware and might not cause the abort handler to be called. See Cache error detection and  
d. See TCM internal error detection and correction on page 8-14 for more information about parity/ECC errors from the TCM.  
e. Aborts generated by external TCM errors are always unrecoverable, and therefore fatal, see External TCM errors on page 8-16  
for more information about external errors from the TCM.  
Correctable errors  
In a system in which the processor is configured to automatically correct ECC errors without  
taking an abort exception, you can still configure it to respond to such errors. Connect the event  
output or outputs that indicate a correctable error to an interrupt controller. When such an event  
occurs, the interrupt input to the processor is set, and the processor will take an interrupt  
exception. When your interrupt handler has identified the source of the interrupt as a correctable  
error, it can read the CFLR to determine where the ECC error occurred. You can examine this  
information to identify trends in such errors. By masking the interrupt when necessary, your  
software can ensure that when critical code is executing, the processor corrects the error  
automatically, but delays examining information about the error until after the critical code has  
completed.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-11  
         
Level One Memory System  
When the processor is in debug halt-state, any correctable error is corrected as appropriate, but  
the memory access is not repeated to fetch the correct data, therefore the instruction generating  
the error does not complete successfully. Instead, the sticky precise abort flag in the DSCR is  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-12  
Level One Memory System  
8.4  
About the TCMs  
The processor has two TCM interfaces to support the connection of local memories. The ATCM  
interface has one TCM port. The BTCM interface can support one or two TCM ports. Each  
TCM port is a physical connection on the processor that is suitable for connection to SRAM  
with minimal glue logic. These ports are optimized for low latency memory.  
The TCM ports are designed to be connected to RAM, or RAM-like memory, that is,  
Normal-type memory. The processor can issue speculative read accesses on these interfaces,  
and interrupt store instructions that have issued some but not all of their write accesses.  
Therefore, both read and write accesses through the TCM interfaces can be repeated. This  
means that the TCM ports are generally not suitable for read- or write-sensitive devices such as  
FIFOs. ROM can be connected to the TCM ports, but normally only if ECC is not used. See  
Hard errors on page 8-5. If the access is speculative, the processor ignores any error or retry  
signaled on the TCM port.  
The TCM ports also have wait and error signals to support slow memories and external error  
detection and correction. For more information, see External TCM errors on page 8-16.  
The PFU can read data using the TCM interfaces. The LSU and AXI slave can each read and  
write data using the TCM interfaces.  
Each TCM interface has a dedicated base address that you can place anywhere in the physical  
address map, and must not be backed by memory implemented externally. The ATCM and  
BTCM interfaces must have separate base addresses and must not overlap.  
This section describes:  
8.4.1  
TCM attributes and permissions  
Accesses to the TCMs from the LSU and PFU are checked against the MPU for access  
permission. Memory access attributes and permissions are not exported on this interface. Reads  
that generate an MPU fault are broadcast on the TCM interface but the abort is taken before the  
data is used, ensuring protection is maintained.  
TCMs always behave as Non-cacheable Non-shared Normal memory, irrespective of the  
memory type attributes defined in the MPU for a memory region containing addresses held in  
the TCM. Access permissions for TCM accesses are the same as the permission attributes that  
the MPU assigns to the same address. See Chapter 7 Memory Protection Unit for more  
information about memory attributes, types, and permissions.  
Note  
Any address in an MPU region with device or strongly-ordered memory type attributes is  
implicitly given execute-never (XN) permissions. If such an address is also in a TCM region,  
XN permissions are applied to TCM accesses to that address. None of the other device or  
strongly-ordered behaviors apply to an address in a TCM region.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-13  
     
Level One Memory System  
8.4.2  
ATCM and BTCM configuration  
The TCM interfaces are configured during implementation and integration.  
You can configure the ATCM interface to be removed, and not included in the processor design.  
If implemented, the ATCM can have only a single port.  
You can configure the BTCM interface to:  
be removed, and not included in the processor design  
have a single BTCM port  
have two banked BTCM ports, interleaved on either:  
Bit [3] of the address  
The most significant bit of the BTCM interface address. This depends on the size of  
the BTCM.  
During implementation, you can configure the ATCM and/or the BTCM to use an  
error-protection scheme to protect the data stored in the TCM, see TCM internal error detection  
The size of each TCM interface is configured during integration. See the Cortex-R4 and  
Cortex-R4F Integration Manual for more information. The permissible TCM sizes are:  
0KB  
4KB  
8KB  
16KB  
32KB  
64KB  
128KB  
256KB  
512KB  
1MB  
2MB  
4MB  
8MB.  
If the BTCM interface has two ports, the size of the RAM attached to each port is half the total  
size for the BTCM interface.  
The size of the TCM interfaces is visible to software in the TCM Region Registers, see c9,  
interface build configuration options can be read from the Build Options Registers, see c15,  
8.4.3  
TCM internal error detection and correction  
Each TCM interface can be configured with either parity, 32-bit ECC, or 64-bit ECC error  
schemes. Both the BTCM ports must have the same error scheme. The following sections  
describe these error schemes:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-14  
     
Level One Memory System  
Handling TCM parity errors  
If a TCM interface has been built with parity error checking, you can enable this by setting the  
appropriate bits in the Auxiliary Control Register. See c1, Auxiliary Control Register on  
page 4-38. If the BTCM interface has been built with two ports, parity checking can be enabled  
for each port individually. You can pin-configure the processor to set the enable bits and  
therefore enable parity checking on reset, by tying off the PARECCENRAM input as required.  
Parity bits for the data are generated on all TCM writes, regardless of whether or not the parity  
bits are being checked on reads. When a parity error is detected on a TCM read, a precise abort  
is generated. The type of the abort is shown in the appropriate Fault Status Register (FSR) as  
being a precise parity error. The processor cannot correct parity errors in the TCM.  
When you use the parity error detection scheme, the PARLVRAM input to the processor selects  
between odd and even parity.  
Handling TCM ECC errors  
If a TCM interface has been built with either 32-bit or 64-bit ECC error checking, you can  
enable this by setting the appropriate bits in the Auxiliary Control Register. See c1, Auxiliary  
Control Register on page 4-38. On the BTCM interface, ECC checking can only be enabled for  
both ports or neither port. You can pin-configure the processor to set the enable bits and  
therefore enable ECC checking on reset, by tying off the PARECCENRAM input as required.  
When a fatal error, that is, a 2-bit ECC error, is detected on a TCM read, an error is generated.  
Instruction and data reads generate the appropriate type of precise abort, and the AXI-slave  
interface returns a SLVERR response to the AXI system.  
When a correctable error, that is, a 1-bit ECC error, is detected on a TCM read made by the  
AXI-slave interface, the processor corrects the data inline before returning to the system.  
When a correctable ECC error is detected on a TCM read made by the instruction-side or  
data-side, the processor normally generates the correct data and writes it back to the TCM. In  
the meantime, the processor retries the read to fetch the correct instruction or data. By setting  
the appropriate bits in the Secondary Auxiliary Control Register, you can disable this behavior.  
the TCM, the processor generates the appropriate type of precise abort.  
All ECC code generation and ECC checking must be performed on a complete data chunk,  
either 32-bits or 64-bits depending on the configuration. If a read access smaller than the data  
chunk is required, the whole chunk is read. If a write smaller than the data chunk is required, the  
processor must perform read-modify-write to generate the correct data and ECC code, but it  
only does this when ECC error checking is enabled. The data read as part of the  
read-modify-write sequence is checked for ECC errors, and the errors are handled in the same  
way as for any other TCM read. The ECC code is generated and written to the TCM for every  
write, regardless of whether error checking is enabled or not, but the code is only correct if the  
write was of a complete data chunk or if the processor performed read-modify-write to generate  
the complete data chunk. All data and instruction aborts generated by the ECC logic are  
indicated in the appropriate FSR as being a precise parity error.  
8.4.4  
TCM arbitration  
Each TCM port receives requests from the LSU, PFU, and AXI slave. In most cases, the LSU  
has the highest priority, followed by the PFU, with the AXI slave having lowest priority.  
When a higher-priority device is accessing a TCM port, an access from a lower-priority device  
must stall.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-15  
     
Level One Memory System  
When either the LSU or the AXI slave interface is performing a read-modify-write operation on  
a TCM port, various internal data hazards exist for either the AXI-slave interface or the LSU.  
In these cases, additional stall cycles are generated, beyond those normally required for  
arbitration. For optimum performance of the processor when configured with ECC, ensure that  
all write bursts to the TCM from the AXI slave interface write an entire data chunk, that is,  
32-bits or 64-bits, naturally aligned, depending on the error scheme.  
8.4.5  
TCM initialization  
You can enable the processor to boot from the ATCM or the BTCM. The INITRAMA and  
INITRAMB pins, when tied HIGH, enable the ATCM and the BTCM respectively on leaving  
reset. The LOCZRAMA pin forces one of the TCMs to have its base address at 0x0. If  
LOCZRAMA is tied HIGH, the initial base address of the ATCM is 0x0, otherwise the initial  
base address of the BTCM is 0x0. In both cases, the initial base address of the other TCM is  
implementation-defined, see Configurable options on page 1-13.  
The ATCM Region Register and BTCM Region Register respectively determine the base  
address for the ATCM and BTCM. For information on how to read the TCM region registers,  
appropriate. For information about pre-loading data into the TCMs, see TCM on page 3-3.  
8.4.6  
TCM port protocol  
Each TCM port operates independently to read and write data to and from the memory attached  
to it. Information about which memory location is to be accessed is passed on the TCM port  
along with write data and associated error code or parity bits, if appropriate. In addition, the  
TCM port provides information about whether the access results from an instruction fetch from  
the PFU, a data access from the LSU, or a DMA transfer from the AXI slave interface. Each  
TCM port also has an associated parity bit, computed from the address and control signals for  
that port.  
Read data and associated error code or parity bits are read back from the TCM port. In addition,  
the TCM memory controller can indicate that the processor must wait one or more cycles before  
reading the response, or signal that an error has occurred and must be either aborted or retried.  
For more information about TCM errors, see External TCM errors.  
For more information about TCM port protocol, the signals and timing, see the Cortex-R4 and  
Cortex-R4F Integration Manual.  
8.4.7  
External TCM errors  
Each TCM port has a number of features that support the integration of a TCM RAM with an  
error checking scheme implemented in the RAM controller logic outside of the processor, that  
is, by the integrator.  
Errors can be signaled to each TCM port if the external error checking scheme detects one and,  
if enabled, the processor generates an instruction or data abort or an AXI error response as  
appropriate. On a TCM read from either the instruction-side or data-side, the TCM controller  
can indicate that the read must be retried instead of generating an abort.  
You can enable external errors for each TCM port individually by setting the appropriate bits in  
the Auxiliary Control Register. See c1, Auxiliary Control Register on page 4-38. If external  
errors are not enabled for a TCM port, the processor ignores any error signaled on that port. You  
can pin-configure the processor to set the enable bits, and therefore enable external error  
checking on reset, by tying off the ERRENRAM input as required.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-16  
       
Level One Memory System  
In addition, an external error detection scheme might require that data is read and written in  
particular sized chunks. The load/store-64 feature, when enabled for a particular TCM interface,  
causes all loads and stores to the TCM ports to be of 64-bits of data. This feature is also known  
as Read-Modify-Write (RMW), because it causes the processor to generate read-modify-write  
sequences for any store of less than 64-bits. You can enable RMW behavior for each TCM  
interface individually by setting the appropriate bits in the Secondary Auxiliary Control  
Register. See c1, Auxiliary Control Register on page 4-38. You can pin-configure the processor  
to set the enable bits and therefore RMW behavior on reset, by tying off the RMWENRAM  
input as required.  
Note  
The load/store-64 feature is not available on any TCM interface that has been configured with  
32-bit ECC.  
The error inputs on each TCM port can also be used to signal other types of error, for example,  
when an address accessed is out of range for the RAM attached to the TCM port. Errors signaled  
on writes from the data-side generate an imprecise abort. All other aborts generated by external  
errors are precise. The type of abort is shown in the appropriate FSR as either precise or  
imprecise parity error.  
8.4.8  
AXI slave interfaces for TCMs  
The processor has a 64-bit AXI slave interface that provides access to the TCM interfaces from  
the AXI bus. This interface is included by default, but can be excluded during configuration of  
the processor.  
You can use the slave port for access to the TCM memories. This also enables you to construct  
a system with a consistent view of memory. That is, the TCMs can be available at the same  
address to the processor and to the system bus.  
The AXI slave port accesses have lower priority than the LSU or PFU accesses.  
The MPU does not check accesses from the AXI slave. You can configure the processor to  
enable privileged or nonprivileged access to the TCM interfaces from the AXI slave port.  
The AXI slave interface does not support locked and exclusive accesses. This means that AXI  
masters, other than the processor, cannot safely use semaphores in the TCMs. Although the  
Cortex-R4 processor can use semaphores in the TCMs for inter-process synchronization, you  
must not use the AXI-slave interface to write to TCM semaphores. The processor has no logic  
to preserve its own exclusivity against such writes.  
For more information on the AXI slave interface, see AXI slave interface on page 9-20.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-17  
 
Level One Memory System  
8.5  
About the caches  
The L1 memory system can be configured to include instruction and data caches of varying  
sizes. You can configure whether the cache controller is included and, if it is, configure the size  
of each cache independently. The cached instructions or data are fetched from external memory  
using the L2 memory interface. The cache controllers use RAMs that are integrated into the  
Cortex-R4 macrocell during implementation.  
Any access that is not for a TCM is handled by the appropriate cache controller. If the access is  
to Cacheable memory, and the cache is enabled, a lookup is performed in the cache and, if found  
in the cache, that is, a cache hit, the data is fetched from or written into the cache. When the  
cache is not enabled and for Non-cacheable memory, the accesses are performed using the L2  
memory interface.  
Both caches allocate a memory location to a cache line on a cache miss because of a read, that  
is, all Cacheable locations are Read-Allocate (RA). In addition, the data cache can allocate on a  
write access if the memory location is marked as Write-Allocate (WA). When a cache line is  
allocated, the appropriate memory is fetched into a linefill buffer by the L2 memory interface  
The linefill buffers always fetch the requested data first, and then the rest of the cache line. This  
enables the data read to be used by the pipeline without waiting for the linefill to complete and  
is known as critical word first and non-blocking behavior. If an error is reported to the L2  
memory interface for a linefill, the linefill does not update the cache RAMs, but an abort is only  
generated if the error was reported on the critical word.  
If all the cache lines in a set are valid, to allocate a different address to the cache, the cache  
controller must evict a line from the cache.  
Writes accesses that hit in the cache are written into the cache RAMs. If the memory location is  
marked as Write-Through (WT), the write is also performed on the L2 memory interface, so that  
the data stored in the RAM remains coherent with the external memory system. If the memory  
is Write-Back (WB), the cache line is marked as dirty, and the write is only performed on the L2  
memory interface when the line is evicted. When a dirty cache line is evicted, the data is passed  
to the Eviction Buffer in the L2 memory interface to be written to the external memory system.  
See Eviction buffer on page 9-5 for more information.  
The cache controllers also manage the cache maintenance operations described in Cache  
Each cache can also be configured with either parity or ECC error checking schemes. If an error  
checking scheme is implemented and enabled, then the tags associated with each line, and data  
read from the cache are checked whenever a lookup is performed in the cache. See Cache error  
For more information on the general rules about memory attributes and behavior, see the ARM  
Architecture Reference Manual.  
8.5.1  
Store buffer  
The cache controller includes a store buffer to hold data before it is written to the cache RAMs  
or passed to the AXI master interface. The store buffer has four entries. Each entry can contain  
up to 64 bits of data and a 32-bit address. All write requests from the data-side that are not to a  
TCM interface are stored in the store buffer.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-18  
       
Level One Memory System  
Store buffer merging  
The store buffer has merging capabilities. If a previous write access has updated an entry, other  
write accesses on the same line can merge into this entry. Merging is only possible for stores to  
Normal memory.  
Merging is possible between several entries that can be linked together if the data inside the  
different entries belong to the same cache line.  
No merging occurs for writes to Strongly Ordered or Device memory. The processor  
automatically drains the store buffer before performing Strongly Ordered accesses or Device  
reads.  
Store buffer behavior  
The store buffer redirects write requests to the following blocks:  
Cache controller for Cacheable write hits:  
The store buffer sends a cache lookup to check that the cache hits in the specified line, and  
if so, the store buffer merges its data into the cache when the entry is drained.  
AXI master interface:  
For Non-cacheable stores or write-through Cacheable stores, a write access is  
performed on the AXI master interface.  
For write-back, write-allocate stores that miss in the data cache, a linefill is started  
using either of the two linefill buffers. When the linefill data is returned from the L2  
memory system, the data in the store buffer is merged into the linefill buffer.  
Store buffer draining  
A store buffer entry is drained if:  
All bytes in the entry have been written. This might result from merging.  
The entry can be merged into a linefill buffer.  
The entry contains a store to Device or Strongly Ordered memory.  
The store buffer is completely drained when:  
an explicit drain request is done for:  
system control coprocessor cache maintenance operations  
DMBor DSBinstruction  
a
a load or store to Strongly Ordered memory  
an exclusive load or store to Shared memory  
a
SWPor SWPBto Non-cacheable memory.  
the store buffer is full or likely to become full.  
The store buffer is drained of all stores to Device memory before a load is performed from  
Device memory.  
8.5.2  
Cache maintenance operations  
All cache maintenance operations are done through the system control coprocessor, CP15. The  
system control coprocessor operations supported for the data cache are:  
Invalidate all  
Invalidate by address (MVA)  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-19  
   
Level One Memory System  
Invalidate by Set/Way combination  
Clean by address (MVA)  
Clean by Set/Way combination  
Clean and Invalidate by address (MVA)  
Clean and Invalidate by Set/Way combination  
Data Memory Barrier (DMB) and Data Synchronization Barrier (DSB) operations.  
The system control coprocessor operations supported for the instruction cache are:  
Invalidate all  
Invalidate by address.  
For more information on cache operations, see Cache operations on page 4-54.  
Cache error detection and correction  
8.5.3  
This section describes how the processor detects, handles, reports, and corrects cache memory  
errors. Memory errors have Fault Status Register (FSR) values to distinguish them from other  
abort causes.  
This section describes:  
Error build options  
The caches can detect and correct errors depending on the build options used in the  
implementation. The build options for the instruction cache can be different to the data cache.  
If the parity build option is enabled, the cache is protected by parity bits. For both the instruction  
and data cache, the data RAMs include one parity bit per byte of data. The tag RAM contains  
one parity bit to cover the tag and valid bit.  
If the ECC build option is enabled:  
The instruction cache is protected by a 64-bit ECC scheme. The data RAMs include eight  
bits of ECC code for every 64 bits of data. The tag RAMs include seven bits of ECC code  
to cover the tag and valid bit.  
The data cache is protected by a 32-bit ECC scheme. The data RAMs include seven bits  
of ECC code for every 32 bits of data. The tag RAMs include seven bits of ECC code to  
cover the tag and valid bit. The dirty RAM includes four bits of ECC to cover the dirty bit  
and the two outer attributes bits.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-20  
   
Level One Memory System  
Address decoder faults  
The error detection schemes described in this section provide protection against errors that  
occur in the data stored in the cache RAMs. Each RAM normally includes a decoder which  
enables access to that data and, if an error occurs in this logic, it is not normally detected by these  
error detection schemes. The processor includes features that enable it to detect some address  
decoder faults. If you are implementing the processor and require these features, contact ARM  
to discuss the features and your requirements.  
Handling cache parity errors  
Table 8-2 shows the behavior of the processor on a cache parity error, depending on bits [5:3]  
of the Auxiliary Control Register, see Auxiliary Control Registers on page 4-38.  
Table 8-2 Cache parity error behavior  
Value Behavior  
b000  
b001  
b010  
b011  
b100  
b101  
b110  
b111  
Abort on all parity errors, force write through, enable hardware recovery  
Reserved  
Disable parity checking  
Force write-through, enable hardware recovery, do not generate aborts on parity errors  
Reserved  
these bits.  
Hardware recovery  
When parity checking is enabled, hardware recovery is always enabled. Memory marked as  
write-back write-allocate behaves as write-though. This ensures that cache lines can never be  
dirty, therefore the error can always be recovered from by invalidating the cache line that  
contains the parity error. The processor automatically performs this invalidation when an error  
is detected. The correct data can then be re-read from the L2 memory system.  
Parity aborts  
If aborts on parity errors are enabled, software is notified of the error by a data abort or prefetch  
abort. The error is still automatically corrected by the hardware even if an abort is generated.  
If abort generation is not enabled, the hardware recovery is invisible to software. If required,  
software can use events and the Correctable Fault Location Register to monitor the errors that  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-21  
         
Level One Memory System  
Handling cache ECC errors  
Table 8-3 shows the behavior of the processor on a cache ECC error, depending on bits [5:3] of  
the Auxiliary Control Register, see Auxiliary Control Registers on page 4-38.  
Table 8-3 Cache ECC error behavior  
Value Behavior  
b000  
b001  
b010  
b011  
b100  
b101  
b110  
b111  
Abort on all ECC errors, enable hardware recovery  
Abort on all ECC errors, force write-through, enable hardware recovery  
Reserved  
Disable ECC checking  
Enable hardware recovery, do not generate aborts on ECC errors  
Force write-through, enable hardware recovery, do not generate aborts on ECC errors  
Reserved  
these bits.  
When ECC checking is enabled, hardware recovery is always enabled. When an ECC error is  
detected, the processor tries to evict the cache line containing the error. If the line is clean, it is  
invalidated, and the correct data is reloaded from the L2 memory system. If the line is dirty, the  
eviction writes the dirty data out to the L2 memory system, and in the process it corrects any  
1-bit errors. The corrected data is then reloaded from the L2 memory system.  
If a 2-bit error is detected in a dirty line, the error is not correctable. If the 2-bit error is in the  
tag or dirty RAM, no data is written to the L2 memory system. If the 2-bit error is in the data  
RAM, the cache line is written to the L2 memory system, but the AXI master port WSTRBM  
signal is LOW for the data that contains the error. If an uncorrectable error is detected, an abort  
is always generated because data might have been lost. It is expected that such a situation can  
be fatal to the software process running.  
If one of the force write-though settings is enabled, memory marked as write-back write-allocate  
behaves as write-though. This ensures that cache lines can never be dirty, therefore the error can  
always be recovered from by invalidating the cache line that contains the ECC error.  
All detectable errors in the instruction cache can always be recovered from because the  
instruction cache can never contain dirty data.  
ECC aborts  
If aborts on ECC errors are enabled, software is notified of the error by a data abort or prefetch  
abort. The error is still automatically corrected by the hardware even if an abort is generated.  
If abort generation is not enabled, the hardware recovery is invisible to software. If required,  
software can use events and the Correctable Fault Location Register to monitor the errors that  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-22  
       
Level One Memory System  
Errors on instruction cache read  
All parity or ECC errors detected on instruction cache reads are correctable. If aborts are  
enabled, a precise prefetch abort exception occurs. The instruction FAR gives the address that  
caused the error to be detected. The instruction FSR indicates a parity error on a read. The  
auxiliary FSR indicates that the error was in the cache and which cache Way the error was in.  
Errors on data cache read  
If parity or ECC aborts are enabled, or an uncorrectable ECC error is detected, a precise data  
abort exception occurs. The data FAR gives the address that caused the error to be detected. The  
data FSR indicates a precise read parity error. The auxiliary FSR indicates that the error was in  
the cache and which cache Way the error was in.  
Errors on data cache write  
If parity or ECC aborts are enabled, or an uncorrectable ECC error is detected, an imprecise data  
abort exception occurs. Because the abort is imprecise, the data FAR is Unpredictable. The data  
FSR indicates an imprecise write parity error. The auxiliary FSR indicates that the error was in  
the cache and which cache Way and Index the error was in.  
In write-through cache regions the store that caused the error is written to external memory  
using the L2 memory interface so data is not lost and the error is not fatal.  
Errors on evictions  
If the cache controller has determined a cache miss has occurred, it might have to do an eviction  
before a linefill can take place. This can occur on reads, and on writes if write-allocation is  
enabled for the region. Certain cache maintenance operations also generate evictions. If it is a  
data-cache line which is dirty, an ECC error might be detected on the line being evicted:  
if the error is correctable, it is corrected inline before the data is written to the external  
memory using the L2 memory interface  
if there is an uncorrectable error in the tag or dirty RAM, the write is not done and an  
imprecise abort occurs  
if there is an uncorrectable error in the data RAM, the AXI master port WSTRBM signal  
is deasserted for the word(s) with an error, and an imprecise abort occurs.  
An imprecise abort can also occur on a correctable error depending on the Auxiliary Control  
with the appropriate event.  
Note  
When parity checking is enabled, force write-though is always enabled. Therefore the cache  
lines can never be dirty, and so evictions are not required. Force write-through can also be  
enabled with ECC checking.  
Errors on cache maintenance operations  
The following sections describe errors on cache maintenance operations:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-23  
         
Level One Memory System  
Invalidate all instruction cache  
This operation ignores all errors in the cache and sets all instruction cache entries to invalid  
regardless of error events. This operation cannot generate an imprecise abort, and no error  
events are signaled.  
Invalidate all data cache  
This operation ignores all errors in the cache and sets all data cache entries to invalid regardless  
of errors. This operation cannot generate an imprecise abort and no error events are signaled.  
Invalidate instruction cache by address  
This operation requires a cache lookup. Any errors found in the set that was looked up are fixed  
by invalidating that line and, if the address in question is found in the set, it is invalidated.  
This operation cannot generate an imprecise abort. Any detected error is signaled with the  
appropriate event.  
Invalidate data cache by address  
This operation requires a cache lookup. Any correctable errors found in the set that was looked  
up are fixed and, if the address in question is found in the set, it is invalidated.  
Any uncorrectable errors cause an imprecise abort. An imprecise abort can also be raised on a  
correctable error if aborts on RAM errors are enabled in the Auxiliary Control Register.  
Any detected error is signaled with the appropriate event.  
Invalidate data cache by set/way  
This operation does not require a cache lookup. It refers to a particular cache line.  
The entry at the given set/way is marked as invalid regardless of any errors. This operation  
cannot generate an imprecise abort. Any detected error is signaled with the appropriate event.  
Clean data cache by address  
This operation requires a cache lookup. Any correctable errors found in the set that was looked  
up are fixed and, if the address in question is found in the set, the instruction carries on with the  
clean operation. When the tag lookup is done, the dirty RAM is checked.  
Note  
When force write-through is enabled, the dirty bit is ignored.  
If the tag or dirty RAM has an uncorrectable error, the data is not written to memory.  
If the line is dirty, the data is written back to external memory. If the data has an uncorrectable  
error, the words with the error have their WSTRBM AXI signal deasserted. If there is a  
correctable error, the line has the error corrected inline before it is written back to memory.  
Any uncorrectable errors cause an imprecise abort. An imprecise abort can also be raised on a  
correctable error if aborts on RAM errors are enabled in the Auxiliary Control Register.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-24  
           
Level One Memory System  
Any detected error is signaled with the appropriate event.  
Clean data cache by set/way  
This operation does not require a cache lookup. It refers to a particular cache line.  
The tag and dirty RAMs for the cache line are checked.  
Note  
When force write-through is enabled, the dirty bit is ignored.  
If the tag or dirty RAM has an uncorrectable error, the data is not written to memory.  
If the line is dirty, the data is written back to external memory. If the data has an uncorrectable  
error, the words with the error have their WSTRBM AXI signal deasserted. If there is a  
correctable error, the line has the error corrected inline before it is written back to memory.  
Any uncorrectable errors found cause an imprecise abort. An imprecise abort can also be raised  
on a correctable error if aborts on RAM errors are enabled in the Auxiliary Control Register.  
Any detected error is signaled with the appropriate event.  
Clean and invalidate data cache by address  
This operation requires a cache lookup. Any correctable errors found in the set that was looked  
up are fixed and, if the address in question is found in the set, the instruction carries on with the  
clean and invalidate operation. When the tag lookup is done, the dirty RAM is checked.  
Note  
When force write-through is enabled, the dirty bit is ignored.  
If the tag or dirty RAM has an uncorrectable error, the data is not written to memory.  
If the line is dirty, the data is written back to external memory. If the data has an uncorrectable  
error, the words with the error have their WSTRBM AXI signal deasserted. If there is a  
correctable error, the line has the error corrected inline before it is written back to memory.  
Any uncorrectable errors found cause an imprecise abort. An imprecise abort can also be raised  
on a correctable error if aborts on RAM errors are enabled in the Auxiliary Control Register.  
Any detected error is signaled with the appropriate event.  
Clean and invalidate data cache by set/way  
This operation does not require a cache lookup. It refers to a particular cache line.  
The tag and dirty RAMs for the cache line are checked.  
Note  
When force write-through is enabled, the dirty bit is ignored.  
If the tag or dirty RAM has an uncorrectable error, the data is not written to memory.  
If the line is dirty, the data is written back to external memory. If the data has an uncorrectable  
error, the words with the error have their WSTRBM AXI signal deasserted. If there is a  
correctable error, the line has the error corrected inline before it is written back to memory.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-25  
     
Level One Memory System  
Any uncorrectable errors found cause an imprecise abort. An imprecise abort can also be raised  
on a correctable error if aborts on RAM errors are enabled in the Auxiliary Control Register.  
Any detected error is signaled with the appropriate event.  
8.5.4  
Cache RAM organization  
This section describes RAM organization in the following sections:  
Tag RAM  
The tag RAMs consist of four ways of up to 512 lines. The width of the RAM depends on the  
build options selected, and the size of the cache. The following tables show the tag RAM bits:  
Table 8-4 shows the tag RAM bits when parity is implemented  
Table 8-5 shows the tag RAM bits when ECC is implemented  
Table 8-6 shows the tag RAM bits when neither parity nor ECC is implemented.  
Table 8-4 Tag RAM bit descriptions, with parity  
Bit in the tag cache line Description  
Bit [23]  
Parity bit  
Valid bit  
Tag value  
Bit [22]  
Bits [21:0]  
Table 8-5 Tag RAM bit descriptions, with ECC  
Bit in the tag cache line Description  
Bits [29:23]  
Bit [22]  
ECC code bits  
Valid bit  
Bits [21:0]  
Tag value  
Table 8-6 Tag RAM bit descriptions, no parity or ECC  
Bit in the tag cache line Description  
Bit [22]  
Valid bit  
Bits [21:0]  
Tag value  
A cache line is marked as valid by bit [22] of the tag RAM. Each valid bit is associated with a  
whole cache line, so evictions always occur on the entire line.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-26  
         
Level One Memory System  
Table 8-7 shows the tag RAM cache sizes and associated RAM organization, assuming no parity  
or ECC. For parity, the width of the tag RAMs must be increased by one bit. For ECC, the width  
of the tag RAMs must be increased by seven bits.  
Table 8-7 Cache sizes and tag RAM organization  
Cache size Tag RAM organization  
4KB  
4 banks 23 bits 32 lines  
4 banks 22 bits 64 lines  
4 banks 21 bits 128 lines  
4 banks 20 bits 256 lines  
4 banks 19 bits 512 lines  
8KB  
16KB  
32KB  
64KB  
Dirty RAM  
For the data cache only, the dirty RAM stores the following information:  
two bits for line outer attributes for evictions  
one line dirty bit  
four ECC code bits if the ECC build option is enabled.  
The dirty RAM array consists of one bank of up to 512 12-bit lines, 4 ways x 3 bits. If ECC is  
enabled, the dirty RAM is 28 bits wide. Each line of dirty RAM contains all the information of  
the four ways for a given index.  
Each time a dirty bit is written, the outer bits of the line and, if implemented, the ECC code bits,  
are also written. The dirty RAM is bit-enabled. Table 8-8 shows the organization of a dirty RAM  
line.  
Table 8-8 Organization of a dirty RAM line  
Bit in the dirty cache line Description  
Bits [6:3]  
Bits [2:1]  
ECC bits, if implemented  
Outer attributes that are re-encoded on AWCACHE when an eviction is sent to the AXI  
bus:  
01 = WB, WA  
10 = WT  
11 = WB, no WA  
00 = Non-cacheable.  
Bit [0]  
Dirty bit  
Data RAM  
Data RAM is organized as eight banks of 32-bit wide lines, or in the instruction cache as four  
banks of 64-bit wide lines. This RAM organization means that it is possible to:  
Perform a cache look-up with one RAM access, all banks selected together. This is done  
for nonsequential read operations. Figure 8-3 on page 8-28 shows this.  
Select the appropriate bank RAM for sequential read operations. Figure 8-4 on page 8-28  
shows this.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-27  
           
Level One Memory System  
Write a line to the eviction buffer in one cycle, a 256-bit read access.  
Fill a line in one cycle from the linefill buffer, a 256-bit write access.  
Figure 8-3 shows a cache look-up being performed on all banks with one RAM access.  
RAM address  
3
Way 1  
Word 7  
Way 2  
Word 7  
Way 3  
Word 7  
Way 0  
Word 6  
Way 0  
Word 7  
Way 1  
Word 6  
Way 2  
Word 6  
Way 3  
Word 6  
Way 2  
Way 3  
Way 0  
Way 1  
Way 2  
Way 3  
Way 0  
Way 1  
2
1
0
Word 5  
Word 5  
Word 5  
Word 5  
Word 4  
Word 4  
Word 4  
Word 4  
Way 3  
Word 3  
Way 0  
Word 3  
Way 1  
Word 3  
Way 2  
Word 3  
Way 3  
Word 2  
Way 0  
Word 2  
Way 1  
Word 2  
Way 2  
Word 2  
Way 0  
Word 1  
Way 1  
Word 1  
Way 2  
Word 1  
Way 3  
Word 1  
Way 0  
Word 0  
Way 1  
Word 0  
Way 2  
Word 0  
Way 3  
Word 0  
Bank 0  
Bank 1  
Bank 2  
Bank 3  
Bank 4  
Bank 5  
Bank 7  
Bank 6  
256-bit wide  
Figure 8-3 Nonsequential read operation performed with one RAM access.  
Figure 8-4 shows the appropriate bank RAM being selected for a sequential read operation.  
RAM address  
3
Way 1  
Word 7  
Way 2  
Word 7  
Way 3  
Word 7  
Way 0  
Word 6  
Way 0  
Word 7  
Way 1  
Word 6  
Way 2  
Word 6  
Way 3  
Word 6  
Way 2  
Way 3  
Way 0  
Way 1  
Way 2  
Way 3  
Way 0  
Way 1  
2
1
0
Word 5  
Word 5  
Word 5  
Word 5  
Word 4  
Word 4  
Word 4  
Word 4  
Way 3  
Word 3  
Way 0  
Word 3  
Way 1  
Word 3  
Way 2  
Word 3  
Way 3  
Word 2  
Way 0  
Word 2  
Way 1  
Word 2  
Way 2  
Word 2  
Way 0  
Word 1  
Way 1  
Word 1  
Way 2  
Word 1  
Way 3  
Word 1  
Way 0  
Word 0  
Way 1  
Word 0  
Way 2  
Word 0  
Way 3  
Word 0  
Bank 0  
Bank 1  
Bank 2  
Bank 3  
Bank 4  
Bank 5  
Bank 7  
Bank 6  
Figure 8-4 Sequential read operation performed with one RAM access  
The data RAM organization is optimized for 64-bit read operations, because with the same  
address, two words on the same way can be selected.  
Data RAM sizes depend on the build option selected, and are described in:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-28  
       
Level One Memory System  
Data RAM sizes without parity or ECC implemented  
Table 8-9 shows the organization for instruction and data caches when neither parity nor ECC  
is implemented.  
Table 8-9 Instruction cache data RAM sizes, no parity or ECC  
Cache size  
Data RAMs  
4KB, 4 1KB ways  
4 banks 64 bits 128 lines or  
8 banks 32 bits 128 lines  
8KB, 4 2KB ways  
16KB, 4 4KB ways  
32KB, 4 8KB ways  
64KB, 4 16KB ways  
4 banks 64 bits 256 lines or  
8 banks 32 bits 256 lines  
4 banks 64 bits 512 lines or  
8 banks 32 bits 512 lines  
4 banks 64 bits 1024 lines or  
8 banks 32 bits 1024 lines  
4 banks 64 bits 2048 lines or  
8 banks 32 bits 2048 lines  
Table 8-10 Data cache data RAM sizes, no parity or ECC  
Cache size  
Data RAMs  
4KB, 4 1KB ways  
8KB, 4 2KB ways  
16KB, 4 4KB ways  
32KB, 4 8KB ways  
64KB, 4 16KB ways  
8 banks 32 bits 128 lines  
8 banks 32 bits 256 lines  
8 banks 32 bits 512 lines  
8 banks 32 bits 1024 lines  
8 banks 32 bits 2048 lines  
Data RAM sizes with parity implemented  
Table 8-11 shows the organization for instruction and data caches when parity is implemented.  
For parity error detection, one bit is added per byte, so four bits are added for each RAM bank.  
Table 8-11 Instruction cache data RAM sizes, with parity  
Cache size  
Data RAMs  
4KB, 4 1KB ways  
4 banks 72 bits 128 lines or  
8 banks 36 bits 128 lines  
8KB, 4 2KB ways  
16KB, 4 4KB ways  
32KB, 4 8KB ways  
64KB, 4 16KB ways  
4 banks 72 bits 256 lines or  
8 banks 36 bits 256 lines  
4 banks 72 bits 512 lines or  
8 banks 36 bits 512 lines  
4 banks 72 bits 1024 lines or  
8 banks 36 bits 1024 lines  
4 banks 72 bits 2048 lines or  
8 banks 36 bits 2048 lines  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-29  
             
Level One Memory System  
Table 8-12 Data cache data RAM sizes, with parity  
Cache size  
Data RAMs  
4KB, 4 1KB ways  
8KB, 4 2KB ways  
16KB, 4 4KB ways  
32KB, 4 8KB ways  
64KB, 4 16KB ways  
8 banks 36 bits 128 lines  
8 banks 36 bits 256 lines  
8 banks 36 bits 512 lines  
8 banks 36 bits 1024 lines  
8 banks 36 bits 2048 lines  
Table 8-13 shows the organization of the data cache RAM bits when parity is implemented.  
Table 8-13 Data cache RAM bits, with parity  
RAM bits  
Description  
Bit [35]  
Bit [34]  
Bit [33]  
Bit [32]  
Bits [31:0]  
Parity bit for byte[31:24]  
Parity bit for byte[23:16]  
Parity bit for byte[15:8]  
Parity bit for byte[7:0]  
Data[31:0]  
Parity bits are grouped together in bits[35:32] so that data and parity bits are easily  
differentiated. With this design the parity bit is selected alongside the related data byte, so that  
when data is updated, the parity bit is also updated.  
Data RAM sizes with ECC implemented  
Table 8-14 shows the organization for the instruction cache when ECC is implemented. For  
ECC error detection, eight bits are added per 64 bits, so four bits are added for each RAM bank.  
Table 8-14 Instruction cache data RAM sizes with ECC  
Cache size  
Data RAMs  
4KB, 4 1KB ways  
4 banks 72 bits 128 lines or  
8 banks 36 bits 128 lines  
8KB, 4 2KB ways  
16KB, 4 4KB ways  
32KB, 4 8KB ways  
64KB, 4 16KB ways  
4 banks 72 bits 256 lines or  
8 banks 36 bits 256 lines  
4 banks 72 bits 512 lines or  
8 banks 36 bits 512 lines  
4 banks 72 bits 1024 lines or  
8 banks 36 bits 1024 lines  
4 banks 72 bits 2048 lines or  
8 banks 36 bits 2048 lines  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-30  
           
Level One Memory System  
Table 8-15 shows the organization for the data cache when ECC is implemented. For ECC error  
detection, seven bits are added per 32 bits, so seven bits are added for each RAM bank.  
Table 8-15 Data cache data RAM sizes with ECC  
Cache size  
Data RAMs  
4KB, 4 1KB ways  
8KB, 4 2KB ways  
16KB, 4 4KB ways  
32KB, 4 8KB ways  
64KB, 4 16KB ways  
8 banks 39 bits 128 lines  
8 banks 39 bits 256 lines  
8 banks 39 bits 512 lines  
8 banks 39 bits 1024 lines  
8 banks 39 bits 2048 lines  
Table 8-16 shows the organization of the data cache RAM bits when ECC is implemented.  
Table 8-16 Data cache RAM bits, with ECC  
RAM bits  
Bits [39:32] ECC code bits for data [31:0]  
Bits [31:0] Data [31:0]  
Description  
8.5.5  
Cache interaction with memory system  
This section describes how to enable or disable the cache RAMs, and to enable or disable error  
checking. After you enable or disable the instruction cache, you must issue an ISBinstruction to  
flush the pipeline. This ensures that all subsequent instruction fetches see the effect of enabling  
or disabling the instruction cache.  
After reset, you must invalidate each cache before enabling it.  
When disabling the data cache, you must clean the entire cache to ensure that any dirty data is  
flushed to L2 memory.  
Before enabling the data cache, you must invalidate the entire data cache if L2 memory might  
have changed since the cache was disabled.  
Before enabling the instruction cache, you must invalidate the entire instruction cache if L2  
memory might have changed since the cache was disabled.  
slave interface on page 9-24 for information about how to access the cache RAMs using the  
AXI slave interface.  
Disabling or enabling all of the caches  
The following code is an example of enabling caches:  
MRC p15, 0, R1, c1, c0, 0 ; Read System Control Register configuration data  
ORR R1, R1, #0x1 <<12  
ORR R1, R1, #0x1 <<2  
DSB  
; instruction cache enable  
; data cache enable  
MCR p15, 0, r0, c15, c5, 0 ; Invalidate entire data cache  
MCR p15, 0, r0, c7, c5, 0 ; Invalidate entire instruction cache  
MCR p15, 0, R1, c1, c0, 0 ; enabled cache RAMs  
ISB  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-31  
       
Level One Memory System  
The following code is an example of disabling the caches:  
MRC p15, 0, R1, c1, c0, 0 ; Read System Control Register configuration data  
BIC R1, R1, #0x1 <<12  
BIC R1, R1, #0x1 <<2  
DSB  
; instruction cache disable  
; data cache disable  
MCR p15, 0, R1, c1, c0, 0 ; disabled cache RAMs  
ISB  
; Clean entire data cache. This routine will depend on the data cache size. It can be  
omitted if it is known that the data cache has no dirty data  
Disabling or enabling instruction cache  
The following code is an example of enabling the instruction cache:  
MRC p15, 0, R1, c1, c0, 0 ; Read System Control Register configuration data  
ORR R1, R1, #0x1 <<12  
; instruction cache enable  
MCR p15, 0, r0, c7, c5, 0 ; Invalidate entire instruction cache  
MCR p15, 0, R1, c1, c0, 0 ; enabled instruction cache  
ISB  
The following code is an example of disabling the instruction cache:  
MRC p15, 0, R1, c1, c0, 0  
BIC R1, R1, #0x1 <<12  
MCR p15, 0, R1, c1, c0, 0  
ISB  
; Read System Control Register configuration data  
; instruction cache enable  
; disabled instruction cache  
Disabling or enabling data cache  
The following code is an example of enabling the data cache:  
MRC p15, 0, R1, c1, c0, 0 ; Read System Control Register configuration data  
ORR R1, R1, #0x1 <<2  
DSB  
MCR p15, 0, r0, c15, c5, 0 ; Invalidate entire data cache  
MCR p15, 0, R1, c1, c0, 0 ; enabled data cache  
The following code is an example of disabling the cache RAMs:  
MRC p15, 0, R1, c1, c0, 0 ; Read System Control Register configuration data  
BIC R1, R1, #0x1 <<2  
DSB  
MCR p15, 0, R1, c1, c0, 0 ; disabled data cache  
; Clean entire data cache. This routine will depend on the data cache size. It can be  
omitted if it is known that the data cache has no dirty data.  
Disabling or enabling error checking  
Software must take care when changing the error checking bits in the Auxiliary Control  
Register. If the bits are changed when the caches contain data, the parity or ECC bits in the  
caches might not be correct for the new setting, resulting in unexpected errors and data loss.  
Therefore the bits in the Auxiliary Control Register must only be changed when both caches are  
turned off and the entire cache must be invalidated after the change.  
The following code is the recommended sequence to perform the change:  
MRC p15, 0, r0, c1, c0, 0 ; Read System Control Register  
BIC r0, r0, #0x1 << 2  
BIC r0, r0, #0x1 << 12  
DSB  
; Disable data cache bit  
; Disable instruction cache bit  
MCR p15, 0, r0, c1, c0, 0 ; Write System Control Register  
ISB ; Ensures following instructions are not executed from cache  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-32  
 
Level One Memory System  
; Clean entire data cache. This routine will depend on the data cache size. It can be  
omitted if it is known that the data cache has no dirty data (e.g. if the cache has not  
been enabled yet).  
MRC p15, 0, r1, c1, c0, 1 ; Read Auxiliary Control Register  
; Change bits 5:3 as needed  
MCR p15, 0, r1, c1, c0, 1 ; Write Auxiliary Control Register  
MCR p15, 0, r0, c15, c5, 0 ; Invalidate entire data cache  
MCR p15, 0, r0, c7, c5, 0 ; Invalidate entire instruction cache  
MRC p15, 0, r0, c1, c0, 0 ; Read System Control Register  
ORR r0, r0, #0x1 << 2  
ORR r0, r0, #0x1 << 12  
DSB  
; Enable data cache bit  
; Enable instruction cache bit  
MCR p15, 0, r0, c1, c0, 0 ; Write System Control Register  
ISB  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-33  
Level One Memory System  
8.6  
Internal exclusive monitor  
The processor L1 memory system has an internal exclusive monitor. This is a two state, open  
and exclusive, state machine that manages load/store exclusive (LDREXB  
STREXand STREXD) accesses and clear exclusive (CLREX) instructions. You can use  
these instructions, operating in the L1 memory system, to construct semaphores and ensure  
,
LDREXH, LDREX, LDREXD,  
STREXB STREXH,  
,
synchronization between different processes. By adding an external exclusive monitor, you can  
also use these instructions in the L2 memory system to construct semaphores and ensure  
synchronization between different processors. See the ARM Architecture Reference Manual for  
more information about how these instructions work.  
When a load-exclusive access is performed, the internal exclusive monitor moves to the  
exclusive state. It moves back to the open state when a store exclusive access or clear exclusive  
instruction is performed. The internal exclusive monitor holds exclusivity state for the  
Cortex-R4 processor only. It does not record the address of the memory that a load-exclusive  
access was performed to. Any store exclusive access performed when the state is open fails. If  
the state is exclusive, the access passes if it is to non-shared memory but, if it is to shared  
memory, the access must be performed as an exclusive using the L2 memory interface. Whether  
the shared store-exclusive access passes or fails depends on the state of an external exclusive  
monitor which can track accesses made by other processors in the system.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-34  
   
Level One Memory System  
8.7  
Memory types and L1 memory system behavior  
The behavior of the L1 memory system depends on the type attribute of the memory that is being  
accessed:  
Only Normal, Non-shared memory can be cached in the RAMs.  
The store buffer can merge any stores to Normal memory. See Store buffer on page 8-18  
for more information.  
Only Normal memory is considered restartable, that is, a multi-word transfer can be  
abandoned part way through because of an interrupt, to be restarted after the interrupt has  
been handled. See Interrupts on page 2-18 for more information about interrupt behavior.  
Only the internal exclusive monitor is used for exclusive accesses to Non-shared memory.  
Exclusive accesses to shared memory are checked using the internal monitor and also, if  
necessary, any external monitor, using the L2 memory interface.  
Accesses resulting from SWPand SWPBinstructions to Cacheable memory are not marked  
as locked when performed using the L2 memory interface.  
Table 8-17 summarizes the processor memory types and associated behavior.  
Table 8-17 Memory types and associated behavior  
Internal  
exclusives  
Locked  
swaps  
Memory type  
Cacheable Merging Restartable  
Normal  
Shared  
No  
Yes  
Yes  
No  
No  
No  
Yes  
Yes  
No  
No  
No  
Partially  
Yes  
Yes  
No  
Non-shared Yes  
Device  
Shared  
No  
Partially  
Yes  
Yes  
Yes  
Yes  
Non-shared No  
Strongly Ordered Shared  
No  
Partially  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-35  
       
Level One Memory System  
8.8  
Error detection events  
The processor generates a number of events related to the internal error detection and correction  
schemes in the TCMs and caches. For more information, see Table 6-1 on page 6-2. This section  
describes:  
8.8.1  
TCM error events  
TCM parity and ECC error events are only signaled for TCM reads, although this includes the  
read-modify-write sequence performed for some stores. Most errors detected by the internal  
parity or ECC logic are signaled twice:  
once on a TCM-centric event  
once on a processor-centric event.  
The TCM-centric events consist of two events per TCM port, one for fatal, that is, 2-bit ECC or  
parity errors and one for correctable, that is, 1-bit ECC errors. These events are generated three  
clock cycles after the data read cycle. Consequently, these events are sometimes signaled on  
speculative TCM reads, such as instructions which are prefetched but never executed because  
of a branch earlier in the instruction sequence.  
Note  
When an external error is signaled on a TCM access, the TCM-centric events are still generated  
as appropriate, based on the data returned, as if no external error had been signaled.  
The processor-centric TCM events are only signaled for errors in data that would have otherwise  
been used by the processor. Errors on speculative reads never generate these errors. They consist  
of fatal and correctable events for:  
the prefetch unit, to signal errors on instruction fetches  
the load/store unit, to signal errors on data accesses  
the AXI slave interface, to signal errors on DMA accesses.  
8.8.2  
8.8.3  
8.8.4  
Instruction-cache error events  
All parity and ECC errors are correctable in the i-cache. Therefore there are only two events, to  
indicate when an error is detected in a read from the tag RAM, or from the data RAM. These  
events are only signaled for non-speculative instruction fetches and certain cache maintenance  
Data-cache error events  
The d-cache can generate fatal and correctable errors, and therefore has four events, one for each  
type of error in the data RAM and in the tag or dirty RAMs. These events are only signaled for  
non-speculative data accesses, cache line evictions, and certain cache maintenance operations.  
Events and the CFLR  
The Correctable Fault Location Register (CFLR) records the location of the last correctable  
error detected on a non-speculative access. See Correctable Fault Location Register on  
page 4-70 for more information. Every correctable error that is recorded in the CFLR also  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-36  
           
Level One Memory System  
generates an event. See Table 6-1 on page 6-2 to see which events are CFLR-related. For  
correctable cache errors, the CLFR does not record whether the error occurred in the data RAM  
or tag/dirty RAM. This distinction is only made by the events.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
8-37  
Chapter 9  
Level Two Interface  
This chapter describes the features of the Level two (L2) interface not covered in the AMBA AXI  
Protocol Specification. It contains the following sections:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-1  
 
Level Two Interface  
9.1  
About the L2 interface  
This section describes the processor L2 interface. The L2 interface consists of AXI master and  
AXI slave interfaces.  
The processor is designed for use in larger chip designs using the Advanced Microcontroller Bus  
Architecture (AMBA) AXI protocol. The processor uses the L2 interfaces as its interface to  
memory and peripheral devices.  
External AXI masters and the processor can use the AXI slave interface to access the processor  
RAMs. You can use the AXI slave interface for DMA access into and out of the TCMs or to  
perform software test of the TCMs and cache RAMs.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-2  
   
Level Two Interface  
9.2  
AXI master interface  
The processor has a single AXI master interface, with one port which is used for:  
I-cache linefills  
D-cache linefills and evictions  
Non-cacheable (NC) Normal-type memory instruction fetches  
NC Normal-type memory data accesses  
Device and Strongly-ordered type data accesses, normally to peripherals.  
The port is 64 bits wide, and conforms to the AXI standard as described in the AMBA AXI  
Protocol Specification. Within the AXI standard, the master port uses the AWUSERM and  
ARUSERM signals to indicate inner memory attributes.  
The master interface can run at the same frequency as the processor or at a lower synchronous  
frequency. See AXI interface clocking on page 3-9 for more information.  
In addition, the AXI master interface produces or checks parity bits for each AXI channel. These  
additional signals are not part of the AXI specification. See the Cortex-R4 and Cortex-R4F  
Integration Manual for more information.  
Note  
References in this section to an AXI slave refer to the AXI slave in the external system which is  
connected to the Cortex-R4 AXI master port. This is not necessarily the Cortex-R4 AXI slave  
port.  
The following sections describe the attributes of the AXI master interface, and provide  
information about the types of burst generated:  
Table 9-1 shows the AXI master interface attributes.  
Table 9-1 AXI master interface attributes  
Attribute  
Value Comments  
Write issuing capability  
4
7
Made up of four outstanding writes that can be evictions, single writes, or write  
bursts.a  
Read issuing capability  
Made up of five linefills on the data side, one NC read on the data side, and one  
read on the instruction side, that can be NC or linefill.  
11a  
2
Combined issuing capability  
Write ID capability  
-
-
Write interleave capability  
Read ID capability  
1
The AXI master interface presents all write data in order.  
7
Made up of five linefills on the data side, one NC read on the data side, and one  
linefill or NC read on the instruction side.  
a. When there are three outstanding write transactions, only data is issued for the fourth. Only three outstanding write addresses  
are issued.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-3  
         
Level Two Interface  
9.2.1  
Identifiers for AXI bus accesses  
Accesses on the AXI bus use ID values as follows:  
Outstanding write/read access on different IDs  
This means, for example, that a Non-cacheable (NC) read and linefills can be  
outstanding on the AXI bus simultaneously as long as the IDs are different.  
At the same time, there can be:  
up to seven outstanding reads, each with one of seven different ID values,  
that consists of:  
a data side read NC access, RID0  
an instruction side read NC access or an instruction side read  
Cacheable access, RID1  
five outstanding data side linefills on the AXI bus, RID3 - RID7.  
up to two IDs on outstanding writes, that consist of:  
single or burst NC writes or write-through (WT) writes, WID0  
evictions, WID1.  
Outstanding write accesses with the same ID  
When the address and data of the first write are both put on AXI bus, another write  
request with same ID can be sent when the address or data channel is released.  
For example, the new address can be sent with the same ID, before the target  
accepts the data of the first write.  
Note  
The AXI master does not generate two outstanding read accesses with the same ID.  
The AXI master does not interleave write data from two different bursts, even if the bursts  
have different IDs.  
9.2.2  
9.2.3  
Write response  
The AXI master requires that the slave does not return a write response until it has received both  
the write data and the write address.  
Linefill buffers and the AXI master interface  
On the data side there are two LineFill Buffers (LFBs), LFB0 and LFB1. Each request from the  
data cache controller or from the STore Buffer (STB) can be allocated to either LFB0 or LFB1.  
On the instruction side, there is one LFB. This is the Instruction LFB (ILFB), that treats  
instruction linefill requests or Non-cacheable instruction reads in the same way.  
The linefill buffers:  
get returned data from the AXI bus for linefill requests  
get returned data from the AXI bus for any Non-cacheable LDRor LDM  
s
get data from the STB to write as a burst on the AXI bus (LFB0 and LFB1 only).  
Single writes do not use LFBs.  
The LFBs are 256 bits wide so that an entire cache line can be written to the cache RAMs in one  
cycle. While the LFB is being filled from L2 memory, its bytes can be merged with write data  
from the STB.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-4  
         
Level Two Interface  
9.2.4  
Eviction buffer  
As soon as a linefill is requested, the selected evicted cache line is loaded into the EViction  
Buffer (EVB). The EVB forwards this information to the AXI bus when possible.  
The EVB has a structure of 256 bits for data and 32 bits for the address. See Cache line  
write-back (eviction) on page 9-13 for details of the AXI transaction generated.  
The EVB is removed if cache RAMs are not implemented for the processor.  
9.2.5  
Memory attributes  
The Cortex-R4 AXI master interface uses the ARCACHEM, AWCACHEM, ARUSERM,  
and AWUSERM signals to indicate the memory attributes of the transfer, as returned by the  
MPU. Table 9-2 Shows the encodings used for the signals ARCACHEM and AWCACHEM  
of the master interface. These are generated from the memory type and outer region attributes.  
Table 9-2 ARCACHEM and AWCACHEM encodings  
Encodinga  
Meaning  
b0000  
b0001  
b0011  
b0110  
b0111  
b1111  
Strongly Ordered  
Device  
Non-cacheable  
Cacheable, write-through, allocate on reads only  
Cacheable, write-back, allocate on reads only  
Cacheable write-back, allocate on reads and writes  
a. All encodings not shown in the table are reserved.  
Table 9-3 shows the encodings the master interface uses for the ARUSERM and AWUSERM  
signals. These are generated from the memory type and inner region attributes.  
Table 9-3 ARUSERM and AWUSERM encodings  
Encodinga  
Meaning  
b00001  
b00010  
b00011  
b00110  
b00111  
b01100  
b01101  
b11110  
b11111  
Strongly Ordered  
Device, Non-shared  
Device, shared  
Non-cacheable, Non-shared  
Non-cacheable, shared  
Cacheable, write-through, read-allocate only, Non-shared  
Cacheable, write-through, read-allocate only, shared  
Cacheable, write-back, read- and write-allocate, Non-shared  
Cacheable, write-back, read- and write-allocate, shared  
a. All encodings not shown in the table are reserved.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-5  
                 
Level Two Interface  
Memory system implications for AXI accesses  
The attributes of the memory being accessed can affect an AXI access. The L1 memory system  
can cache any Normal memory address that is marked as either:  
Cacheable, write-back, read- and write-allocate, non-shared  
Cacheable, write-through, read-allocate only, non-shared.  
However, Device and Strongly Ordered memory is always Non-cacheable. Also, any unaligned  
access to Device or Strongly Ordered memory generates an alignment fault and therefore does  
not cause any AXI transfer. This means that the access examples given in this chapter never  
show unaligned accesses to Device or Strongly Ordered memory.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-6  
Level Two Interface  
9.3  
AXI master interface transfers  
The processor conforms to the AXI specification, but it does not generate all the AXI transaction  
types that the specification permits. This section describes the types of AXI transaction that the  
Cortex-R4 AXI master does not generate. If you are designing an AXI slave to work only with  
the Cortex-R4 processor, and there are no other AXI masters in your system, you can take  
advantage of these restrictions and the interface attributes described above to simplify the slave.  
This section also contains tables that show some of the types of AXI burst that the processor  
generates. However, because a particular type of transaction is not shown here does not mean  
that the processor does not generate such a transaction.  
Note  
An AXI slave device connected to the Cortex-R4 AXI master port must be capable of handling  
every kind of transaction permitted by the AXI specification, except where there is an explicit  
statement in this chapter that such a transaction is not generated. You must not infer any  
additional restrictions from the example tables given. Restrictions described here are applicable  
to the r1p0, r1p1, and r1p2 revisions of the processor, and might not be true for future revisions.  
Load and store instructions to Non-cacheable memory might not result in an AXI transfer  
because the data might either be retrieved from, or merged into the internal store data buffers.  
The exceptions to this are loads or stores to Strongly Ordered or Device memory. These always  
Restrictions on AXI transfers on page 9-8 describes restrictions on the type of transfers that the  
Cortex-R4 AXI master interface generates. The AXI master port never deasserts the buffered  
write response and read data channel ready signals, BREADYM and RREADYM. You must  
not make any other assumptions about the AXI handshaking signals, except that they conform  
to the AMBA AXI Protocol Specification.  
The following sections give examples of transfers generated by the AXI master interface:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-7  
   
Level Two Interface  
9.3.1  
Restrictions on AXI transfers  
The Cortex-R4 AXI master interface applies the following restrictions to the AXI transactions  
it generates:  
A burst never transfers more than 32 bytes.  
The burst length is never more than 8 transfers.  
No transaction ever crosses a 32-byte boundary in memory. See AXI transaction splitting  
FIXED bursts are never used.  
The write address channel always issues INCR type bursts, and never WRAP or FIXED.  
WRAP type read bursts, see Linefills on page 9-13:  
are used only for linefills (reads) of Cacheable Normal non-shared memory  
always have a size of 64 bits, and a length of 4 transfers  
always have a start address that is 64-bit aligned.  
If the transfer size is 8 bits or 16 bits then the burst length is always 1 transfer.  
The transfer size is never greater than 64 bits, because it is a 64-bit AXI bus.  
Instruction fetches, identified by ARPROT[2], are always a 64 bit transfer size, and never  
locked or exclusive.  
Transactions to Device and Strongly Ordered memory are always to addresses that are  
aligned for the transfer size. See Strongly Ordered and Device transactions.  
Exclusive and Locked accesses are always to addresses that are aligned for the transfer  
size.  
Write data is never interleaved.  
In addition to the above, there are various limitations to the ID values that the AXI master  
9.3.2  
Strongly Ordered and Device transactions  
A load or store instruction to or from Strongly Ordered or Device memory always generates  
AXI transactions of the same size as implied by the instruction. All accesses using LDM STM, LDRD,  
,
or STRDinstructions to Strongly Ordered or Device memory occur as 32-bit transfers.  
LDRB  
Table 9-4 shows the values of ARADDRM, ARBURSTM, ARSIZEM, and ARLENM for a  
Non-cacheable LDRBfrom bytes 0-7 in Strongly Ordered or Device memory.  
Table 9-4 Non-cacheable LDRB  
Address[2:0] ARADDRM ARBURSTM ARSIZEM ARLENM  
0x0(byte 0)  
0x1(byte 1)  
0x2(byte 2)  
0x3(byte 3)  
0x00  
0x01  
0x02  
0x03  
Incr  
Incr  
Incr  
Incr  
8-bit  
8-bit  
8-bit  
8-bit  
1 data transfer  
1 data transfer  
1 data transfer  
1 data transfer  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-8  
       
Level Two Interface  
Table 9-4 Non-cacheable LDRB (continued)  
Address[2:0] ARADDRM ARBURSTM ARSIZEM ARLENM  
0x4(byte 4)  
0x5(byte 5)  
0x6(byte 6)  
0x7(byte 7)  
0x04  
0x05  
0x06  
0x07  
Incr  
Incr  
Incr  
Incr  
8-bit  
8-bit  
8-bit  
8-bit  
1 data transfer  
1 data transfer  
1 data transfer  
1 data transfer  
LDRH  
Table 9-5 shows the values of ARADDRM, ARBURSTM, ARSIZEM, and ARLENM for a  
Non-cacheable LDRHfrom halfwords 0-3 in Strongly Ordered or Device memory.  
Table 9-5 LDRH from Strongly Ordered or Device memory  
Address[3:0]  
ARADDRM ARBURSTM ARSIZEM ARLENM  
0x0(halfword 0)  
0x2(halfword 1)  
0x4(halfword 2)  
0x6(halfword 3)  
0x00  
0x02  
0x04  
0x06  
Incr  
Incr  
Incr  
Incr  
16-bit  
16-bit  
16-bit  
16-bit  
1 data transfer  
1 data transfer  
1 data transfer  
1 data transfer  
Note  
A load of a halfword from Strongly Ordered or Device memory addresses 0x1 0x3, 0x5, or 0x7  
,
generates an alignment fault.  
LDR or LDM that transfers one register  
Table 9-6 shows the values of ARADDRM, ARBURSTM, ARSIZEM, and ARLENM for a  
Non-cacheable LDRor an LDMthat transfers one register, (an LDM1) in Strongly Ordered or Device  
memory.  
Table 9-6 LDR or LDM1 from Strongly Ordered or Device memory  
Address[2:0] ARADDRM ARBURSTM ARSIZEM ARLENM  
0x0(word 0)  
0x00  
0x04  
Incr  
Incr  
32-bit  
32-bit  
1 data transfer  
1 data transfer  
0x4(word 1)  
Note  
A load of a word from Strongly Ordered or Device memory addresses 0x1  
,
0x2  
,
0x3  
,
0x5  
,
0x6, or  
0x7generates an alignment fault.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-9  
       
Level Two Interface  
LDM that transfers five registers  
Table 9-7 shows the values of ARADDRM, ARBURSTM, ARSIZEM, and ARLENM for a  
Non-cacheable LDMthat transfers five registers (an LDM5) in Strongly Ordered or Device memory.  
Table 9-7 LDM5, Strongly Ordered or Device memory  
Address[4:0] ARADDRM ARBURSTM ARSIZEM ARLENM  
0x00(word 0)  
0x04(word 1)  
0x08(word 2)  
0x0C(word 3)  
0x00  
0x04  
0x08  
0x0C  
Incr  
Incr  
Incr  
Incr  
32-bit  
32-bit  
32-bit  
32-bit  
5 data transfers  
5 data transfers  
5 data transfers  
5 data transfers  
Note  
A load-multiple from address 0x1  
,
0x2  
,
0x3  
,
0x5  
,
0x6  
,
0x7  
,
0x9  
,
0xA  
,
0xB  
,
0xD  
,
0xE, or 0xFgenerates  
an alignment fault.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-10  
   
Level Two Interface  
STRB  
Table 9-8 shows the values of AWADDRM, AWBURSTM, AWSIZEM, and AWLENM for  
an STRBto Strongly Ordered or Device memory over the AXI master port.  
Table 9-8 STRB to Strongly Ordered or Device memory  
Address[4:0] AWADDRM AWBURSTM AWSIZEM AWLENM  
WSTRBM  
0x00(byte 0)  
0x01(byte 1)  
0x02(byte 2)  
0x03(byte 3)  
0x04(byte 4)  
0x05(byte 5)  
0x06(byte 6)  
0x07(byte 7)  
0x00  
0x01  
0x02  
0x03  
0x04  
0x05  
0x06  
0x07  
Incr  
Incr  
Incr  
Incr  
Incr  
Incr  
Incr  
Incr  
8-bit  
8-bit  
8-bit  
8-bit  
8-bit  
8-bit  
8-bit  
8-bit  
1 data transfer b00000001  
1 data transfer b00000010  
1 data transfer b00000100  
1 data transfer b00001000  
1 data transfer b00010000  
1 data transfer b00100000  
1 data transfer b01000000  
1 data transfer b10000000  
STRH  
Table 9-9 shows the values of AWADDRM, AWBURSTM, AWSIZEM, and AWLENM for  
an STRHover the AXI master port to Strongly Ordered or Device memory.  
Table 9-9 STRH to Strongly Ordered or Device memory  
Address[2:0]  
AWADDRM AWBURSTM AWSIZEM AWLENM  
WSTRBM  
0x0(halfword 0)  
0x2(halfword 1)  
0x4(halfword 2)  
0x6(halfword 3)  
0x00  
0x02  
0x04  
0x06  
Incr  
Incr  
Incr  
Incr  
16-bit  
16-bit  
16-bit  
16-bit  
1 data transfer b00000011  
1 data transfer b00001100  
1 data transfer b00110000  
1 data transfer b11000000  
Note  
A store of a halfword to Strongly Ordered or Device memory addresses 0x1 0x3, 0x5, or 0x7  
,
generates an alignment fault.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-11  
       
Level Two Interface  
STR or STM of one register  
Table 9-10 shows the values of AWADDRM, AWBURSTM, AWSIZEM, and AWLENM for  
an STRor an STMthat transfers one register (an STM1) over the AXI master port to Strongly  
Ordered or Device memory.  
Table 9-10 STR or STM1 to Strongly Ordered or Device memory  
Address[2:0] AWADDRM AWBURSTM AWSIZEM AWLENM  
WSTRBM  
0x0(word0)  
0x00  
0x04  
Incr  
Incr  
32-bit  
32-bit  
1 data transfer b00001111  
1 data transfer b11110000  
0x4(word 1)  
Note  
A store of a word to Strongly Ordered or Device memory addresses 0x1 0x2, 0x3, 0x5, 0x6, or  
,
0x7generates an alignment fault.  
STM of seven registers  
Table 9-11 shows the values of AWADDRM, AWBURSTM, AWSIZEM, and AWLENM for  
an STMthat writes seven registers (an STM7) over the AXI master port to Strongly Ordered or  
Device memory.  
Table 9-11 STM7 to Strongly Ordered or Device memory to word 0 or 1  
Address[4:0] AWADDRM AWBURSTM AWSIZEM AWLENM  
First WSTRBM  
0x00(word 0)  
0x00  
0x04  
Incr  
Incr  
32-bit  
32-bit  
7 data transfers b00001111  
7 data transfers b11110000  
0x04(word 1)  
Note  
A store-multiple to address 0x1  
,
0x2, 0x3, 0x5, 0x6, or 0x7generates an alignment fault.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-12  
       
Level Two Interface  
9.3.3  
Linefills  
Loads and instruction fetches from Normal, Cacheable memory that do not hit in the cache  
generate a cache linefill when the appropriate cache is enabled. Table 9-12 shows the values of  
ARADDRM, ARBURSTM, ARSIZEM, and ARLENM for cache linefills.  
Table 9-12 Linefill behavior on the AXI interface  
Address[4:0]a  
ARADDRM ARBURSTM ARSIZEM ARLENM  
0x00  
0x08  
0x10  
0x18  
-
-
-
-
0x07  
0x0F  
0x17  
0x1F  
0x00  
0x08  
0x10  
0x18  
Wrap  
Wrap  
Wrap  
Wrap  
64-bit  
64-bit  
64-bit  
64-bit  
4 data transfers  
4 data transfers  
4 data transfers  
4 data transfers  
a. These are the bottom five bits of the address of the access that cause the linefill, that  
is, the address of the critical word.  
9.3.4  
Cache line write-back (eviction)  
When a valid and dirty cache line is evicted from the d-cache, a write-back of the data must  
occur. Table 9-13 shows the values of AWADDRM, AWBURSTM, AWSIZEM, and  
AWLENM for cache line write-backs, over the AXI master interface.  
Table 9-13 Cache line write-back  
AWADDRM[4:0] AWBURSTM AWSIZEM AWLENM  
0x00  
Incr  
64-bit  
4 data transfers  
9.3.5  
Non-cacheable reads  
Load instructions accessing Non-cacheable Normal memory generate AXI bursts that are not  
necessarily the same size or length as the instruction implies. In addition, if the data to be read  
is contained in the store buffer, the instruction might not generate an AXI read transaction at all.  
The tables in this section give examples of the types of AXI transaction that might result from  
various load instructions, accessing various addresses in Non-cacheable Normal memory. They  
are provided as examples only, and are not an exhaustive description of the AXI transactions.  
Depending on the state of the processor, and the timing of the accesses, the actual bursts  
generated might have a different size and length to the examples shown, even for the same  
instruction.  
Table 9-14 shows possible values of ARADDRM, ARBURSTM, ARSIZEM, and ARLENM  
for an LDRHfrom bytes 0-7 in Non-cacheable Normal memory.  
Table 9-14 LDRH from Non-cacheable Normal memory  
Address[2:0] ARADDRM ARBURSTM ARSIZEM ARLENM  
0x0(byte 0)  
0x1(byte 1)  
0x2(byte 2)  
0x3(byte 3)  
0x00  
0x00  
0x00  
0x03  
Incr  
Incr  
Incr  
Incr  
16-bit  
32-bit  
64-bit  
32-bit  
1 data transfer  
1 data transfer  
1 data transfer  
2 data transfers  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-13  
                 
Level Two Interface  
Table 9-14 LDRH from Non-cacheable Normal memory (continued)  
Address[2:0] ARADDRM ARBURSTM ARSIZEM ARLENM  
0x4(byte 4)  
0x5(byte 5)  
0x6(byte 6)  
0x7(byte 7)  
0x04  
0x04  
0x06  
0x07  
Incr  
Incr  
Incr  
Incr  
16-bit  
32-bit  
16-bit  
32-bit  
1 data transfer  
1 data transfer  
1 data transfer  
2 data transfers  
Table 9-15 shows possible values of ARADDRM, ARBURSTM, ARSIZEM, and ARLENM  
for a Non-cacheable LDRor an LDMthat transfers one register, an LDM1.  
Table 9-15 LDR or LDM1 from Non-cacheable Normal memory  
Address[2:0]  
ARADDRM ARBURSTM ARSIZEM ARLENM  
0x0(byte 0) (word 0)  
0x1(byte 1)  
0x00  
0x01  
0x00  
0x00  
0x04  
0x05  
0x06  
0x08  
0x04  
Incr  
Incr  
Incr  
Incr  
Incr  
Incr  
Incr  
Incr  
Incr  
32-bit  
64-bit  
64-bit  
64-bit  
32-bit  
32-bit  
16-bit  
16-bit  
32-bit  
1 data transfer  
1 data transfer  
1 data transfer  
2 data transfers  
1 data transfer  
2 data transfers  
1 data transfer  
1 data transfer  
2 data transfers  
0x2(byte 2)  
0x3(byte 3)  
0x4(byte 4) (word 1)  
0x5(byte 5)  
0x6(byte 6)  
0x7(byte 7)  
Table 9-16 show possible values of ARADDRM, ARBURSTM, ARSIZEM, and ARLENM  
for a Non-cacheable LDMthat transfers five registers (an LDM5).  
Table 9-16 LDM5, Non-cacheable Normal memory or cache disabled  
Address[4:0] ARADDRM ARBURSTM ARSIZEM ARLENM  
0x00(word 0)  
0x04(word 1)  
0x08(word 2)  
0x0C(word 3)  
0x10(word 4)  
0x00  
0x04  
0x08  
0x0C  
0x10  
0x00  
0x14  
0x00  
Incr  
Incr  
Incr  
Incr  
Incr  
Incr  
Incr  
Incr  
64-bit  
64-bit  
64-bit  
64-bit  
64-bit  
32-bit  
64-bit  
64-bit  
3 data transfers  
3 data transfers  
3 data transfers  
3 data transfers  
2 data transfers  
1 data transfer  
2 data transfers  
1 data transfer  
0x14(word 5)  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-14  
       
Level Two Interface  
Table 9-16 LDM5, Non-cacheable Normal memory or cache disabled (continued)  
Address[4:0] ARADDRM ARBURSTM ARSIZEM ARLENM  
0x18(word 6)  
0x18  
0x00  
0x1C  
0x00  
Incr  
Incr  
Incr  
Incr  
64-bit  
64-bit  
32-bit  
64-bit  
1 data transfer  
2 data transfers  
1 data transfer  
2 data transfers  
0x1C(word 7)  
9.3.6  
Non-cacheable or write-through writes  
Store instructions to Non-cacheable or write-through Normal memory generate AXI bursts that  
are not necessarily the same size or length as the instruction implies. The AXI master port  
asserts byte-lane-strobes, WSTRBM[7:0], to ensure that only the bytes that were written by the  
instruction are updated.  
The tables in this section give examples of the types of AXI transaction that might result from  
various store instructions, accessing various addresses in Non-cacheable Normal memory. They  
are provided as examples only, and are not an exhaustive description of the AXI transactions.  
Depending on the state of the processor, and the timing of the accesses, the actual bursts  
generated might have a different size and length to the examples shown, even for the same  
instruction.  
In addition, write operations to Normal memory can be merged to create more complex AXI  
Table 9-17 shows possible values of AWADDRM, AWBURSTM, AWSIZEM, and  
AWLENM for an STRHto Normal memory.  
Table 9-17 STRH to Cacheable write-through or Non-cacheable Normal memory  
Address[2:0] AWADDRM  
AWBURSTM AWSIZEM AWLENM  
WSTRBM  
0x0(byte 0)  
0x1(byte 1)  
0x2(byte 2)  
0x3(byte 3)  
0x00  
0x00  
0x02  
0x03  
Incr  
Incr  
Incr  
Incr  
32-bit  
32-bit  
64-bit  
32-bit  
1 data transfer  
1 data transfer  
1 data transfer  
b00000011  
b00000110  
b00001100  
2 data transfers b00001000  
b00010000  
0x4(byte 4)  
0x5(byte 5)  
0x6(byte 6)  
0x7(byte 7)  
0x04  
0x05  
0x06  
0x07  
0x08  
Incr  
Incr  
Incr  
Incr  
Incr  
16-bit  
32-bit  
16-bit  
8-bit  
1 data transfer  
1 data transfer  
1 data transfer  
1 data transfer  
1 data transfer  
b00110000  
b01100000  
b11000000  
b10000000  
b00000001  
8-bit  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-15  
     
Level Two Interface  
Table 9-18 shows possible values of AWADDRM, AWBURSTM, AWSIZEM, and  
AWLENM for an STRor an STMthat transfers one register, an STM1, to Normal memory through  
the AXI master port.  
Table 9-18 STR or STM1 to Cacheable write-through or Non-cacheable Normal memory  
Address[2:0]  
AWADDRM AWBURSTM AWSIZEM AWLENM  
WSTRBM  
0x0(byte 0) (word 0)  
0x1(byte 1)  
0x00  
0x01  
0x00  
0x03  
Incr  
Incr  
Incr  
Incr  
32-bit  
64-bit  
64-bit  
64-bit  
1 data transfer  
1 data transfer  
1 data transfer  
b00001111  
b00011110  
b00111100  
0x2(byte 2)  
0x3(byte 3)  
2 data transfers b01111000  
b00000000  
0x4(byte 4) (word 1)  
0x04  
0x05  
Incr  
Incr  
32-bit  
32-bit  
1 data transfer  
b11110000  
0x5(byte 5)  
2 data transfers b11100000  
b00000001  
0x6(byte 6)  
0x06  
0x08  
Incr  
Incr  
16-bit  
16-bit  
1 data transfer  
1 data transfer  
b11000000  
b00000011  
0x7(byte 7)  
0x04  
Incr  
32-bit  
2 data transfers b10000000  
b00000111  
9.3.7  
AXI transaction splitting  
The processor splits AXI bursts when it accesses addresses across a cache line boundary, that  
is, a 32-byte boundary. An instruction which accesses memory across one or two 32-byte  
boundaries generates two or three AXI bursts respectively. The following examples show this  
behavior. They are provided as examples only, and are not an exhaustive description of the AXI  
transactions. Depending on the state of the processor, and the timing of the accesses, the actual  
bursts generated might have a different size and length to the examples shown, even for the same  
instruction.  
For example, LDMIA R10, {R0-R5}loads six words from memory. The number of AXI  
transactions generated by this instruction depends on the base address, R10:  
If all six words are in the same cache line, there is a single AXI transaction. For example,  
for LDMIA R10, {R0-R5}with R10 = 0x1008, the interface might generate a burst of three,  
64-bit read transfers, as shown in Table 9-19.  
Table 9-19 AXI transaction splitting, all six words in same cache line  
ARADDRM ARBURSTM ARSIZEM ARLENM  
0x1008  
Incr  
64-bit  
3 data transfers  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-16  
         
Level Two Interface  
If the data comes from two cache lines, then there are two AXI transactions. For example,  
for LDMIA R10, {R0-R5}with R10 = 0x1010, the interface might generate one burst of two  
64-bit reads, and one burst of a single 64-bit read, as shown in Table 9-20.  
Table 9-20 AXI transaction splitting, data in two cache lines  
ARADDRM ARBURSTM ARSIZEM ARLENM  
0x1010  
0x1020  
Incr  
Incr  
64-bit  
64-bit  
2 data transfers  
1 data transfer  
Table 9-21 shows possible values of ARADDRM, ARBURSTM, ARSIZEM, and ARLENM  
for an LDRor LDM1 to Non-cacheable Normal memory that crosses a cache line boundary.  
Table 9-21 Non-cacheable LDR or LDM1 crossing a cache line boundary  
Address[4:0] ARADDRM ARBURSTM ARSIZEM ARLENM  
0x1D(byte 29)  
0x1E(byte 30)  
0x1F (byte 31)  
0x1C  
0x00  
0x1E  
0x00  
0x1F  
0x00  
Incr  
Incr  
Incr  
Incr  
Incr  
Incr  
32-bit  
32-bit  
16-bit  
64-bit  
8-bit  
1 data transfer  
1 data transfer  
1 data transfer  
1 data transfer  
1 data transfer  
1 data transfer  
32-bit  
Table 9-22 shows possible values of ARADDRM, ARBURSTM, ARSIZEM, and ARLENM  
for an STRHto Non-cacheable Normal memory that crosses a cache line boundary.  
Table 9-22 Cacheable write-through or Non-cacheable STRH crossing a cache line  
boundary  
Address[4:0] AWADDRM AWBURSTM AWSIZEM AWLENM  
WSTRBM  
0x1F(byte 31)  
0x1F  
0x00  
Incr  
Incr  
8-bit  
1 data transfer b10000000  
1 data transfer b00000001  
16-bit  
9.3.8  
Normal write merging  
A store instruction to Non-cacheable, or write-through Normal memory might not result in an  
AXI transfer because of the merging of store data in the internal buffers.  
The STB can detect when it contains more than one write request to the same cache line for  
write-through Cacheable or Non-cacheable Normal memory. This means it can combine the  
data from more than one instruction into a single write burst to improve the efficiency of the  
AXI port. If the AXI master receives several write requests that do not form a single contiguous  
burst it can choose to output a single burst, with the WSTRBW signal low for the bytes that do  
not have any data.  
For write accesses to Normal memory, the STB can perform writes out of order, if there are no  
address dependencies. It can do this to best use its ability to merge accesses.  
The instruction sequence in Example 9-1 on page 9-18 shows the merging of writes.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-17  
             
Level Two Interface  
Example 9-1 Write merging  
MOV r0, #0x4000  
STRH r1, [r0, #0x18]; Store a halfword at 0x4018  
STR  
STMIA r0, {r4-r7}  
STRB r3, [r0, #0x1D]; Store a byte at 0x401D  
r2, [r0, #0xC] ; Store a word at 0x400C  
; Store four words at 0x4000  
If the memory at address 0x4000is marked as Strongly Ordered or Device type memory, the AXI  
transactions shown in Table 9-23 are generated.  
Table 9-23 AXI transactions for Strongly Ordered or Device type memory  
AWADDRM AWBURSTM AWSIZEM AWLENM  
WSTRBM  
0x4018  
0x400C  
0x4000  
Incr  
Incr  
Incr  
16-bit  
32-bit  
32-bit  
1 data transfer  
1 data transfer  
0b00000011  
0b11110000  
4 data transfers 0b00001111  
0b11110000  
0b00001111  
0b11110000  
0x401D  
Incr  
8-bit  
1 data transfer  
0b00100000  
In the example above, each store instruction produces an AXI burst of the same size as the data  
written by the instruction.  
Table 9-24 shows a possible resulting transaction if the same memory is marked as  
Non-cacheable Normal, or Cacheable write-through.  
Table 9-24 AXI transactions for Non-cacheable Normal or Cacheable write-through  
memory  
AWADDRM AWBURSTM  
Incr  
AWSIZEM AWLENM  
WSTRBM  
0x4000  
64-bit  
4 data transfers 0b11111111  
0b11111111  
0b00000000  
0b00100011  
In this example:  
The store buffer has merged the STRBand STRHwrites into one buffer entry, and therefore  
a single AXI transfer, the fourth in the burst.  
The writes, which occupy three buffer entries, have been merged into a single AXI burst  
of four transfers.  
The write generated by the STRinstruction has not occurred, because it was overwritten by  
the STMinstruction.  
The write transfers have occurred out of order with respect to the original program order.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-18  
         
Level Two Interface  
The transactions shown in Table 9-24 on page 9-18 show this behavior. They are provided as  
examples only, and are not an exhaustive description of the AXI transactions. Depending on the  
state of the processor, and the timing of the accesses, the actual bursts generated might have a  
different size and length to the examples shown, even for the same instruction.  
If the same memory is marked as write-back Cacheable, and the addresses are allocated into a  
cache line, no AXI write transactions occur until the cache line is evicted and performs a  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-19  
Level Two Interface  
9.4  
AXI slave interface  
The processor has a single AXI slave interface, with one port. The port is 64 bits wide and  
conforms to the AXI standard as described in the AMBA AXI Protocol Specification. Within the  
AXI standard, the slave port uses the AWUSERS and ARUSERS each as four separate chip  
select input signals to enable access to:  
BTCM  
ATCM  
instruction cache RAMs  
data cache RAMs.  
The external AXI system must generate the chip select signals. The slave interface routes the  
access to the required RAM.  
In addition, the AXI slave interface produces or checks parity bits for each AXI channel. These  
additional signals are not part of the AXI specification. See the Cortex-R4 and Cortex-R4F  
Integration Manual for more information.  
The slave interface can run at the same frequency as the processor or at a lower, synchronous  
frequency. See AXI interface clocking on page 3-9 for more information. If asynchronous  
clocking is required an external asynchronous AXI register slice is required.  
The AXI slave provides access to the TCMs and competes for access to the TCMs with the LSU  
and PFU. Both the LSU and PFU normally have a higher priority than the AXI slave.  
If two BTCM ports are used, you can configure these to interleave in the address map, so any  
AXI slave access that is denied access to the BTCM on the first cycle of the access gains access  
on the second cycle when the LSU is using the other port, and can continue in lock-step with the  
LSU, assuming both are accessing sequential data. Accesses to the ATCM are more likely to  
encounter a conflict because there is only one port on the interface.  
Memory BIST ports are routed through the AXI slave interface logic, to access the RAMs.  
Memory BIST access is assumed only to occur when no other accesses are taking place, and  
takes highest priority.  
9.4.1  
AXI slave interface for cache RAMs  
You can use the AXI slave for software testing of the cache RAMs in functional mode. When  
the AXI slave is enabled to access the RAMs, the processor considers the caches as cache-off,  
so that the instruction and data requests cannot interact with AXI slave requests. AXI slave  
requests access the cache RAMs. Instruction and data requests are considered as Non-cacheable  
and do not perform any lookup in the caches.  
The AXI slave interface accesses each cache RAM individually.  
On the instruction cache side the AXI slave can access:  
data cache RAMs, data and parity or ECC code bits  
tag RAMs, tag and parity or ECC code bits.  
On the data cache side, the AXI slave can access:  
data cache RAMs, data and parity or ECC code bits  
tag RAMs, tag and parity or ECC code bits  
dirty RAM, dirty bit and attributes, and ECC code bits.  
A simple decode of two address bits and four way address bits determines which of the data,  
tag, or dirty RAMs is accessed within the caches. The AXI access is given a SLVERR error  
response when access to nonexistent cache RAM is indicated.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-20  
   
Level Two Interface  
9.4.2  
TCM parity and ECC support  
The TCMs can support parity or ECC, as described in TCM internal error detection and  
correction on page 8-14. If a write transaction is issued to the AXI slave, the slave interface  
calculates the required parity or ECC bits to store to the TCM. ECC schemes require the AXI  
slave to perform a read-modify-write sequence if the write data width is smaller than the ECC  
chunk size.  
If a read transaction is issued to the AXI slave, the slave interface reads the parity or ECC bits  
and, if error checking is enabled for the appropriate TCM, checks the data for errors. If the  
interface detects a correctable error, it corrects it inline and returns the correct data on the AXI  
bus. It does not update the data in the TCM to correct it. If the interface detects an uncorrectable  
error, it generates a SLVERR error response to the AXI transaction.  
9.4.3  
9.4.4  
External TCM errors  
If an error response is given to a TCM access from the AXI slave interface, and external errors  
are enabled for the appropriate TCM port, the AXI slave returns a SLVERR response to the AXI  
transaction.  
The AXI slave ignores late-error and retry responses from the TCM.  
Cache parity and ECC support  
When the caches support parity or ECC, the AXI slave interface can read and write the parity  
or ECC code bits directly. No errors are detected automatically, and on writes the AXI slave does  
not automatically generate the correct parity or ECC code values.  
Note  
The AXI slave interface provides read/write access to the cache RAMs for functional test. It is  
not suitable for preloading the caches.  
9.4.5  
AXI slave control  
By default, both privileged and non-privileged accesses can be made to the Cortex-R4 TCM  
RAMs through the AXI slave port. To disable non-privileged accesses, you can set bit [1] in the  
Slave Port Control Register. You can disable all slave accesses by setting bit [0] of the register.  
Access to the cache RAMs can only be made when bit [24] of the Auxiliary Control Register is  
set. By default, only privileged accesses can be made to the cache RAMs, but you can enable  
non-privileged accesses by setting bit [23] of the Auxiliary Control Register. When cache RAM  
access is enabled, both caches are treated as if they were not enabled. See Auxiliary Control  
The AXI access is given a SLVERR error response when access is not permitted.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-21  
 
Level Two Interface  
9.4.6  
AXI slave characteristics  
This section describes the capabilities of the AXI slave interface, and the attributes of its AXI  
port. You must not make any other assumptions about the behavior of the AXI slave port except  
that it conforms to the AMBA AXI Protocol Specification.  
The AXI slave interface supports merging of data. When handling an AXI burst of data  
less than 64-bits wide, the AXI slave interface attempts to perform the minimum number  
of TCM accesses required to read or write the data. When an ECC error scheme is in use,  
this sometimes reduces the number of read-modify-write sequences that the AXI slave  
must perform.  
The AXI slave interface does not support:  
Security Extensions, all accesses are secure, so AxPROT[1] is not used  
data and instruction transaction signaling, so AxPROT[2] is not used  
memory type and cacheability, so AxCACHE is not used  
atomic accesses. The AXI slave accepts locked transactions but makes no use of the  
locking information, that is, AxLOCK.  
The AXI slave interface has no exclusive access monitor. If there are any exclusive  
accesses, the AXI slave interface responds with an OKAY response.  
The width of the ID signals for the AXI slave port is 8 bits.  
You must avoid building the processor into an AXI system that requires more than 8 bits  
of ID. The number of bits of ID required by a system can often be reduced by compressing  
the encoding to remove unused values. The AXI master port does not use all possible  
Table 9-25 shows the AXI slave port attributes.  
Table 9-25 AXI slave interface attributes  
Attribute  
Value Comments  
Combined acceptance capability  
Write interleave depth  
7
1
1
-
All write data must be presented to the AXI slave interface in order  
Read data reorder depth  
The AXI slave interface returns all read data in order, even if the bursts  
have different IDs  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-22  
   
Level Two Interface  
9.5  
Enabling or disabling AXI slave accesses  
This section describes how to enable or disable AXI slave accesses to the cache RAMs. When  
caches are accessible by the AXI slave interface, the caches are considered to be cache-off from  
the processor. After turning the interface on or off, an ISBinstruction must flush the pipeline so  
that all subsequent instruction fetches return valid data.  
The following code is an example of enabling AXI slave accesses to the cache RAMs:  
MRC p15, 0, R1, c1, c0, 1 ; Read Auxiliary Control Register  
ORR R1, R1, #0x1 <<24  
DSB  
MCR p15, 0, R1, c1, c0, 1 ; enabled AXI slave accesses to the cache RAMs  
ISB  
; Clean entire data cache. This routine will depend on the data cache size. It can be  
omitted if it is known that the data cache has no dirty data  
Fetch from uncached memory  
Fetch from uncached memory  
Fetch from uncached memory  
Fetch from uncached memory  
The following code is an example of disabling AXI slave accesses to the cache RAMs. No cache  
invalidation is performed because it is assumed that, after accessing the cache RAMs, the AXI  
slave interface restored the previously valid data to them.  
MRC p15, 0, R1, c1, c0, 1  
BIC R1, R1, #0x1 <<24  
DSB  
; Read Auxiliary Control Register  
MCR p15, 0, R1, c1, c0, 1  
ISB  
; disabled AXI slave accesses to the cache RAMs  
Fetch from cached memory  
Fetch from cached memory  
Fetch from cached memory  
Fetch from cached memory  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-23  
   
Level Two Interface  
9.6  
Accessing RAMs using the AXI slave interface  
This section describes how to access the TCM and cache RAMs using the AXI slave interface.  
Table 9-26 shows the bits of the ARUSERS or AWUSERS inputs to use to access RAM or a  
group of RAMs. Each bit is a one-hot 4-bit input, with each bit corresponding to a particular  
RAM or group of RAMs.  
Table 9-26 RAM region decode  
AxUSERS bit One-hot RAM select  
[3]  
[2]  
[1]  
[0]  
Data cache RAMs  
Instruction cache RAMs  
B0TCM and B1TCM  
ATCM  
For the caches and the BTCMs, more decoding is performed depending on the address of the  
request, ARADDRS for reads and AWADDRS for writes. For more information see:  
Note  
Because AWUSERS and AWADDRS work in the same way as ARUSERS and ARADDRS,  
the following sections only describe ARUSERS and ARADDRS.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-24  
       
Level Two Interface  
9.6.1  
TCM RAM access  
Table 9-27 shows the decode of the ARUSERS[3:0] signal, and the state of the address signals  
for accessing the TCM RAMs. The table also shows the SLBTCMSB configuration input signal  
that determines the address bit that is used, either:  
ARADDRS[3]  
ARADDRS[MSB], see Table 9-28.  
Table 9-27 TCM chip-select decode  
BTCM ports ARUSERS[3:0] ARADDRS[3] ARADDRS[MSB] SLBTCMSB RAM selected  
Don’t care  
0001  
0010  
0010  
0010  
0010  
0010  
-
-
-
ATCM  
1
2
2
2
2
-
-
-
B0TCM  
B0TCM  
B1TCM  
B0TCM  
B1TCM  
0
1
-
-
0
0
1
1
-
0
1
-
In Table 9-27 ARADDRS[MSB] means the most significant address bit for the TCM RAM, and  
Table 9-28 shows the MSB bit for the different TCM RAM sizes.  
Table 9-28 MSB bit for the different TCM RAM sizes  
TCM size  
ARADDRS[MSB]  
4KB  
[11]  
[12]  
[13]  
[14]  
[15]  
[16]  
[17]  
[18]  
[19]  
[20]  
[21]  
[22]  
8KB  
16KB  
32KB  
64KB  
128KB  
256KB  
512KB  
1MB  
2MB  
4MB  
8MB  
ARADDRS[22:3] indicates the address of the doubleword within the TCM that you want to  
access. If you are accessing a TCM that is smaller than the maximum 8MB, then it is possible  
to address a doubleword that is outside of the physical size of the TCM.  
An access to the TCM RAMs is given a SLVERR error response if:  
It is outside the physical size of the targeted TCM RAM, that is, bits of  
ARADDRS[22:MSB+1] are non-zero.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-25  
         
Level Two Interface  
There is no TCM present. The mapping of bus addresses to ARUSERS and ARADDRS  
is determined when the processor is integrated. You must understand this mapping to use  
of the AXI-slave interface within your system.  
9.6.2  
Cache RAM access  
This section contains the following:  
Memory map when accessing the cache RAMs  
The memory maps for the data and instruction caches have the same format. Because the  
instruction cache does not have a dirty RAM, accesses to it generate the SLVERR error  
response.  
Table 9-29, Table 9-30, and Table 9-31 on page 9-27 show the chip-select decodes for selecting  
the cache RAMs in the processor.  
Table 9-29 Cache RAM chip-select decode  
Inputs  
RAM selected  
ARUSERS[3:0] ARADDRS[22:19]  
0100  
0100  
0100  
0100  
0100  
1000  
1000  
1000  
1000  
1000  
0000  
0001  
0010  
0011  
Instruction cache data RAM  
Instruction cache tag RAM  
Not used, generates an error  
Not used, generates an error  
ARADDRS[22:21] != 00 Not used, generates an error  
0000  
0001  
0010  
0011  
Data cache data RAM  
Data cache tag RAM  
Data cache dirty RAM  
Not used, generates an error  
ARADDRS[22:21] != 00 Not used, generates an error  
Table 9-30 Cache tag/valid RAM bank/address decode  
Inputs  
RAMbank Cache  
selected  
way  
ARADDRS[18:15]  
0001  
Bank 0  
0
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-26  
         
Level Two Interface  
Table 9-30 Cache tag/valid RAM bank/address decode (continued)  
Inputs  
RAMbank Cache  
selected  
way  
ARADDRS[18:15]  
0010  
0100  
1000  
Bank 1  
Bank 2  
Bank 3  
1
2
3
Table 9-31 Cache data RAM bank/address decode  
Inputs  
RAM bank  
selected  
ARADDRS[18:15] ARADDRS[3]  
0001  
0001  
0010  
0010  
0100  
0100  
1000  
1000  
0
1
0
1
0
1
0
1
Bank 0  
Bank 1  
Bank 2  
Bank 3  
Bank 4  
Bank 5  
Bank 6  
Bank 7  
Note  
You can only access the cache RAMs using 32-bit or 64-bit AXI transfers. Using an 8-bit or a  
16-bit transfer size generates a SLVERR error response.  
Data RAM access  
The following tables shows the data formats for cache data RAM accesses:  
Table 9-32 shows the format when neither parity nor ECC is implemented  
Table 9-33 on page 9-28 shows the format when parity is implemented  
Table 9-34 on page 9-28 shows the instruction cache format when ECC is implemented  
Table 9-35 on page 9-28 shows the data cache format when ECC is implemented.  
Table 9-32 Data format, instruction cache and data cache, no parity and no ECC  
Data bit Description  
[63:48]  
[47:32]  
[31:16]  
[15:0]  
Not used, read-as-zero  
Data value, [31:16] or [63:48]  
Not used, read-as-zero  
Data value, [15:0] or [47:32]  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-27  
       
Level Two Interface  
Table 9-33 Data format, instruction cache and data cache, with parity  
Data bit Description  
[63:50]  
[49]  
Not used, read-as-zero  
Parity bit for data value [31:24] or [63:56]  
Parity bit for data value [23:16] or [55:48]  
Data value, [31:16] or [63:48]  
[48]  
[47:32]  
[31:18]  
[17]  
Not used, read-as-zero  
Parity bit for data value [15:8] or [47:40]  
Parity bit for data value [7:0] or [39:32]  
Data value, [15:0] or [47:32]  
[16]  
[15:0]  
Table 9-34 Data format, instruction cache, with ECC  
Description  
Data bit  
[63:52]  
[51:48]  
[47:32]  
[31:20]  
[19:16]  
[15:0]  
Not used, read-as-zero  
Upper or lower half of the ECC 64 codea  
Data value, [31:16] or [63:48]  
Not used, read-as-zero  
Upper or lower half of the ECC 64 codeb  
Data value, [15:0] or [47:32]  
a. If accessing bits [31:16] of the data, bits [51:48] hold the lower half of the ECC code.  
If accessing bits [63:48] of the data, bits [51:48] hold the upper half of the ECC code.  
b. If accessing bits [15:0] of the data, bits [19:16] hold the lower half of the ECC code.  
If accessing bits [47:32] of the data, bits [19:16] hold the upper half of the ECC code.  
Table 9-35 Data format, data cache, with ECC  
Data bit  
Description  
[63:55]  
[54:48]  
[47:32]  
[31:23]  
[22:16]  
[15:0]  
Not used, read-as-zero  
ECC 32 codea  
Data value, [31:16] or [63:48]  
Not used, read-as-zero  
ECC 32 code  
Data value [15:0] or [47:32]  
a. For a 64 bit access, the ECC bits are  
duplicated in bits [22:16] and bits  
[54:48], and the two copies are identical.  
For a 32 bit access, the ECC bits refer to  
the whole 32 bit data value, even though  
only 16 bits of data are accessed.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-28  
     
Level Two Interface  
Tag RAM access  
The following tables show the data formats for tag RAM accesses:  
Table 9-36 shows the format for read accesses when neither parity nor ECC is  
implemented  
Table 9-37 shows the format for read accesses when parity is implemented  
Table 9-38 shows the format for read accesses when ECC is implemented  
Table 9-39 on page 9-30 shows the format for write accesses when neither parity nor ECC  
is implemented  
Table 9-40 on page 9-30 shows the format for write accesses when parity is implemented  
Table 9-41 on page 9-30 shows the format for write accesses when ECC is implemented.  
Table 9-36 Tag register format for reads, no parity or ECC  
Data bit  
Description  
[63:55]  
[54]  
Not used, read-as-zero  
Valid, way 2/3  
[53:32]  
[31:23]  
[22]  
Tag value, way 2/3  
Not used, read-as-zero  
Valid, way 0/1  
[21:0]  
Tag value, way 0/1  
Table 9-37 Tag register format for reads, with parity  
Data bit  
Description  
[63:56]  
[55]  
Not used, read-as-zero  
Parity, way 2/3  
[54]  
Valid, way 2/3  
[53:32]  
[31:24]  
[23]  
Tag value, way 2/3  
Not used, read-as-zero  
Parity, way 0/1  
[22]  
Valid, way 0/1  
[21:0]  
Tag value, way 0/1  
Table 9-38 Tag register format for reads, with ECC  
Data bit  
Description  
[63:62]  
[61:55]  
[54]  
Not used, read-as-zero  
ECC, way 2/3  
Valid, way 2/3  
[53:32]  
Tag value, way 2/3  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-29  
         
Level Two Interface  
Table 9-38 Tag register format for reads, with ECC (continued)  
Data bit  
Description  
[31:30]  
[29:23]  
[22]  
Not used, read-as-zero  
ECC, way 0/1  
Valid, way 0/1  
[21:0]  
Tag value, way 0/1  
Table 9-39 Tag register format for writes, no parity or ECC  
Data bit Description  
[63:23]  
[22]  
Not used, read-as-zero  
Valid, all ways  
[21:0]  
Tag value, all ways  
Table 9-40 Tag register format for writes, with parity  
Data bit Description  
[63:24]  
[23]  
Not used, read-as-zero  
Parity. all ways  
[22]  
Valid, all ways  
[21:0]  
Tag value, all ways  
Table 9-41 Tag register format for writes, with ECC  
Data bit Description  
[63:30]  
[29:23]  
[22]  
Not used, read-as-zero  
ECC, all ways  
Valid, all ways  
[21:0]  
Tag value, all ways  
Note  
For tag RAM writes, only bits [23:0] of the data bus are used. If two tag RAMs are written at  
the same time, they are both written with the same data. To write only one tag RAM using the  
AXI Slave, select only one RAM with bits [18:15] of the address bus.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-30  
     
Level Two Interface  
Dirty RAM access  
The following tables show the data format for accessing the dirty RAM:  
Table 9-42 shows the format when parity is implemented, or no error scheme is  
implemented  
Table 9-43 shows the format when ECC is implemented.  
Table 9-42 Dirty register format, with parity or with no error scheme  
Data bit  
Description  
[63:27]  
[26:25]  
[24]  
Not used, read-as-zero  
Outer attributes, way 3  
Dirty value, way 3  
[23:19]  
[18:17]  
[16]  
Not used, read-as-zero  
Outer attributes, way 2  
Dirty value, way 2  
[15:11]  
[10:9]  
[8]  
Not used, read-as-zero  
Outer attributes, way 1  
Dirty value, way 1  
[7:3]  
Not used, read-as-zero  
Outer attributes, way 0  
Dirty value, way 0  
[2:1]  
[0]  
Note  
When parity checking is enabled, all Cacheable accesses are forced to write-through. Therefore  
the dirty RAM is not used and does not require parity protection.  
Table 9-43 Dirty register format, with ECC  
Data bit  
Description  
[63:31]  
[30:27]  
[26:25]  
[24]  
Not used, read-as-zero  
ECC, way 3  
Outer attributes, way 3  
Dirty value, way 3  
Not used, read-as-zero  
ECC, way 2  
[23]  
[22:19]  
[18:17]  
[16]  
Outer attributes, way 2  
Dirty value, way 2  
Not used, read-as-zero  
[15]  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-31  
         
Level Two Interface  
Table 9-43 Dirty register format, with ECC (continued)  
Data bit  
Description  
[14:11]  
[10:9]  
[8]  
ECC, way 1  
Outer attributes, way 1  
Dirty value, way 1  
Not used, read-as-zero  
ECC, way 0  
[7]  
[6:3]  
[2:1]  
[0]  
Outer attributes, way 0  
Dirty value, way 0  
Other examples of accessing cache RAMs  
Normally ARADDRS[18:15] is a one-hot field, and only accesses one RAM at a time.  
However, if you want to access two tag RAMs, such as banks 0 and 2 or banks 1 and 3 at the  
same time, use:  
ARADDRS[18:15] = 4'b0101 to access banks 0 and 2  
ARADDRS[18:15] = 4'b1010 to access banks 1 and 3.  
This enables data to be read from two tag RAMs simultaneously, and the same data to be written  
to two tag RAMs simultaneously. To write different data to each tag RAM, you must ensure only  
one tag RAM is accessed at a time.  
You can access any combination of dirty RAM banks simultaneously. For example, to access all  
dirty RAM banks use:  
ARADDRS[18:15] = 4'b1111.  
If you break these rules, for example if you access tag RAM banks 0 and 1, no SLVERR  
response is generated, and any attempt to read or write banks in other combinations or multiple  
banks of other RAMs is Unpredictable.  
Note  
If you attempt to read or write cache RAMs outside the physical cache size implemented, the  
MSBs for that read or write access are ignored. For example, accessing 0x10000000or 0x00000000  
addresses in the cache RAM accesses the same physical location 0x0. This means that such  
accesses are aliased and no errors are generated.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
9-32  
 
Chapter 10  
Power Control  
This chapter describes the processor power control functions. It contains the following sections:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
10-1  
   
PowerControl  
10.1 About power control  
The features of the processor that improve energy efficiency include:  
branch and return prediction, reducing the number of incorrect instruction fetch and  
decode operations  
the caches use sequential access information to reduce the number of accesses to the tag  
RAMs and to unwanted data RAMs.  
In the processor, extensive use is also made of gated clocks and gates to disable inputs to unused  
functional blocks. Only the logic actively in use to perform a calculation consumes any dynamic  
power.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
10-2  
   
PowerControl  
10.2 Power management  
The processor supports four levels of power management. This section describes:  
10.2.1 Run mode  
Run mode is the normal mode of operation where all of the functionality of the processor is  
available.  
10.2.2 Standby mode  
Standby mode disables most of the clocks of the device, while keeping the design powered up.  
This reduces the power drawn to the static leakage current, plus a tiny clock power overhead  
required to enable the device to wake up from the Standby mode.  
The transition from Standby mode to Run mode is caused by:  
the arrival of an interrupt, whether masked or unmasked  
a debug request, whether debug is enabled or disabled  
a reset.  
The debug request can be generated by an externally generated debug request, using the  
EDBGRQ pin on the processor, or from a Debug Halt instruction issued to the processor  
through the debug Advanced Peripheral Bus (APB).  
Entry into Standby mode is performed by executing the Wait For Interrupt (WFI) instruction. To  
ensure that the entry into the Standby mode does not affect the memory system, the WFI  
automatically performs a Data Synchronization Barrier operation. This ensures that all explicit  
memory accesses occur in program order before the WFIhas completed.  
Systems using the VIC interface must ensure that the VIC is not masking any interrupts that are  
required for restarting the processor when in this mode of operation.  
When the processor clocks are stopped the STANDBYWFI signal is asserted to indicate that  
the processor is in Standby mode.  
When the processor is in Standby mode and the AXI slave interface receives a transaction, the  
processor clocks are temporarily restarted and STANDBYWFI is deasserted to enable it to  
service the transaction, but it does not return to Run mode.  
10.2.3 Dormant mode  
Dormant mode ensures that only the processor logic, but not the processor TCM and cache  
RAMs, is powered down. In dormant mode, the processor state, apart from the cache and TCM  
state, is stored to memory before entry into this mode, and restored after exit. For more  
information on how to implement and use dormant mode in your design, contact ARM.  
10.2.4 Shutdown mode  
Shutdown mode has the entire device powered down, and you must externally save all state,  
including cache and TCM state. The processor is returned to Run mode by asserting and  
deasserting nRESET. When you perform state saving, you must ensure that interrupts are  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
10-3  
             
PowerControl  
disabled and finish with a Data Synchronization Barrier operation. When all the state of the  
processor is saved the processor executes a WFIinstruction. The STANDBYWFI signal is  
asserted to indicate that the processor can enter Shutdown mode.  
10.2.5 Communication to the Power Management Controller  
You can use a Power Management Controller (PMC) to control the powering up and powering  
down of the processor. The communication mechanism between the processor and the PMC is  
a memory-mapped controller that is accessed by the processor performing Strongly-Ordered  
accesses to it.  
The STANDBYWFI signal from the processor informs the PMC of the powerdown mode to  
adopt.  
The STANDBYWFI signal can also signal that the processor is ready to have its power state  
changed. STANDBYWFI is asserted in response to a WFIoperation.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
10-4  
 
Chapter 11  
Debug  
This chapter describes the processor debug unit. These features assist the development of  
application software, operating systems, and hardware. This chapter contains the following  
sections:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-1  
   
Debug  
11.1 Debug systems  
The Cortex-R4 processor is one component of a debug system. Figure 11-1 shows a typical  
system.  
Debug  
host  
Host computer running RealView Debugger  
Protocol  
For example, RealView ICE  
converter  
Debug  
target  
Development system containing  
Cortex-R4 processor  
Figure 11-1 Typical debug system  
This typical system has three parts, described in the following sections:  
11.1.1 Debug host  
The debug host is a computer, for example a personal computer, running a software debugger  
such as RealViewDebugger. The debug host enables you to issue high-level commands such  
as setting breakpoint at a certain location, or examining the contents of a memory address.  
11.1.2 Protocol converter  
The debug host connects to the processor development system using an interface such as  
Ethernet. The messages broadcast over this connection must be converted to the interface  
signals of the debug target. A protocol converter performs this function, for example, RealView  
ICE.  
11.1.3 Debug target  
The debug target is the lowest level of the system. An example of a debug target is a  
development system with a Cortex-R4 test chip or a silicon part with a Cortex-R4 macrocell.  
The debug target must implement some system support for the protocol converter to access the  
processor debug unit using the Advanced Peripheral Bus (APB) slave port.  
The debug unit enables you to:  
stall program execution  
examine the internal state of the processor and the state of the memory system  
resume program execution.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-2  
             
Debug  
11.2 About the debug unit  
The processor debug unit assists in debugging software running on the processor. You can use  
the processor debug unit, in combination with a software debugger program, to debug:  
application software  
operating systems  
ARM processor-based hardware systems.  
The debug unit enables you to:  
stop program execution  
examine and alter processor state  
examine and alter memory and peripheral state  
restart the processor.  
You can debug software running on the processor in the following ways:  
Halting debug-mode debugging  
Monitor debug-mode debugging  
Trace debugging, see ETM interface on page 1-11.  
The processor debug unit conforms to the ARMv7 debug architecture. For more information see  
the ARM Architecture Reference Manual.  
11.2.1 Halting debug-mode debugging  
When the processor debug unit is in Halting debug-mode, the processor halts when a debug  
event, such as a breakpoint, occurs. When the processor is halted, an external debugger can  
examine and modify the processor state using the APB slave port. This debug mode is invasive  
to program execution.  
11.2.2 Monitor debug-mode debugging  
When the processor debug unit is in Monitor debug-mode, the processor takes a debug  
exception instead of halting. A special piece of software, a monitor target, can then take control  
to examine or alter the processor state. Monitor debug-mode is essential in real-time systems  
where the processor cannot be halted to collect information. Examples of these systems are  
engine controllers and servo mechanisms in hard drive controllers that cannot stop the code  
without physically damaging the components.  
When debugging in Monitor debug-mode, the processor stops execution of the current program  
and starts execution of a monitor target. The state of the processor is preserved in the same  
manner as all ARM exceptions. The monitor target communicates with the debugger to access  
processor and coprocessor state, and to access memory contents and peripherals. Monitor  
debug-mode requires a debug monitor program to interface between the debug hardware and the  
software debugger.  
11.2.3 Programming the debug unit  
The processor debug unit is programmed using the APB slave interface. See Table 11-3 on  
page 11-6 for a complete list of memory-mapped debug registers accessible using the APB slave  
interface. Some features of the debug unit that you can access using the memory-mapped  
registers are:  
instruction address comparators for triggering breakpoints, see Breakpoint Value  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-3  
     
Debug  
data address comparators for triggering watchpoints, see Watchpoint Value Registers on  
a bidirectional Debug Communication Channel (DCC), see Debug communications  
all other state information associated with the debug unit.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-4  
Debug  
11.3 Debug register interface  
You can access the processor debug register map using the APB slave port. This is the only way  
to get full access to the processor debug capability. ARM recommends that if your system  
requires the processor to access its own debug registers, you choose a system interconnect  
structure that enables the processor to access the APB slave port by executing load and stores  
to an appropriate area of physical memory.  
This section describes:  
11.3.1 Coprocessor registers  
Although most of the processor debug registers are accessible through the memory-mapped  
interface, there are several registers that you can access through a coprocessor interface. This is  
important for boot-strap access to the register file. It enables software running on the processor  
to identify the debug architecture version that the device implements.  
11.3.2 CP14 access permissions  
By default, you can access all CP14 debug registers from a nonprivileged mode. However, you  
can program the processor to disable user-mode access to all coprocessor registers using bit [12]  
information. CP14 debug registers accesses are always permitted when the processor is in debug  
state regardless of the processor mode.  
Table 11-1 shows access to the CP14 debug registers.  
Table 11-1 Access to CP14 debug registers  
Debug state Processor mode DSCR[12]  
CP14 debug access  
Yes  
No  
No  
No  
X
X
Permitted  
User  
b0  
b1  
X
Permitted  
Not permitteda  
Permitted  
User  
Privileged  
a. Instructions attempting to access CP14 registers cause the processor to take an  
Undefined exception.  
11.3.3 Coprocessor registers summary  
Table 11-2 on page 11-6 shows a set of valid CP14 instructions for accessing the debug  
registers. All CP14 instructions not listed are Undefined.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-5  
             
Debug  
Note  
The CP14 debug instructions are defined as having Opcode_1 set to 0.  
Table 11-2 CP14 debug registers summary  
Instruction  
Mnemonic Description  
MRC p14, 0, <Rd>, c0, c0, 0  
DIDR  
Debug Identification Register. See CP14 c0, Debug ID Register on  
MRC p14, 0, <Rd>, c1, c0, 0  
MRC p14, 0, <Rd>, c2, c0, 0  
DRAR  
DSAR  
DTRRX  
DTRTX  
DSCR  
Debug ROM Address Register. See CP14 c0, Debug ROM Address  
Debug Self Address Register. See CP14 c0, Debug Self Address  
MRC p14, 0, <Rd>, c0, c5, 0  
STC p14, c5, <addressing mode>  
Host to Target Data Transfer Register. See Data Transfer Register on  
MCR p14, 0, <Rd>, c0, c5, 0  
LDC p14, c5, <addressing mode>  
Target to Host Data Transfer Register. See Data Transfer Register on  
MRC p14, 0, <Rd>, c0, c1, 0  
MRC p14, 0, PC, c0, c1, 0  
Debug Status and Control Register. See CP14 c1, Debug Status and  
11.3.4 Memory-mapped registers  
Table 11-3 shows the complete list of memory-mapped registers accessible at the APB slave  
interface.  
Note  
You must ensure that the base address of this 4KB register map is aligned to a 4KB boundary in  
physical memory.  
Table 11-3 Debug memory-mapped registers  
Offset  
(hex)  
Register  
Access Mnemonic Description  
number  
0x000  
c0  
R
DIDR  
0x004-0x014  
0x18  
c1-c5  
c6  
R
-
RAZ  
RW  
RW  
R
WFAR  
0x01C  
c7  
VCR  
0x020  
c8  
-
RAZ  
0x024  
c9  
RW  
RW  
R
ECR  
Not implemented in this processor. Reads as zero.  
0x028  
c10  
c11  
c12-c31  
DSCCR  
0x02C  
-
-
RAZ  
RAZ  
0x030-0x07C  
R
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-6  
         
Debug  
Table 11-3 Debug memory-mapped registers (continued)  
Offset  
(hex)  
Register  
number  
Access Mnemonic Description  
0x080  
c32  
RW  
W
DTRRX  
ITR  
0x084  
c33  
0x088  
c34  
RW  
RW  
W
DSCR  
DTRTX  
DRCR  
-
0x08C  
c35  
0x090  
c36  
0x094-0x0FC  
0x100-0x11C  
0x120-0x13C  
0x140-0x15C  
0x160-0x17C  
0x180-0x19C  
0x1A0-0x1BC  
0x1C0-0x1DC  
0x1E0-0x1FC  
0x200-0x2FC  
0x300  
c37-c63  
c64-c71  
c72-c79  
c80-c87  
c88-c95  
c96-c103  
c104-c111  
c112-c119  
c120-c127  
c128-c191  
c192  
R
RAZ  
RW  
R
BVR  
-
RAZ  
RW  
R
BCR  
-
RAZ  
RW  
R
WVR  
-
RAZ  
RW  
R
WCR  
-
RAZ  
R
-
RAZ  
R
OSLAR  
OSLSR  
OSSRR  
-
Not implemented in this processor. Reads as zero.  
Not implemented in this processor. Reads as zero.  
RAZ  
0x304  
c193  
R
0x308  
c194  
R
0x30C  
c195  
R
0x310  
c196  
RW  
PRCR  
0x314  
c197  
R
R
R
R
R
R
-
PRSR  
0x318-0x7FC  
0x800-0x8FC  
0x900-0xCFC  
c198-c511  
c512-575  
c576-c831  
c832-c895  
c896-c927  
c928-c959  
c960-c1023  
-
-
-
-
-
-
-
RAZ  
RAZ  
RAZ  
0xD00  
0xE00  
0xE80  
-
-
-
0xDFC  
0xE7C  
0xEFC  
RAZ  
0xF00-0xFFC  
-
11.3.5 Memory addresses for breakpoints and watchpoints  
The Vector Catch Register (VCR) sets breakpoints on exception vectors as instruction  
addresses.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-7  
 
Debug  
The Watchpoint Fault Address Register (WFAR) reads an address and a processor state  
dependent offset, +8 for ARM and +4 for Thumb.  
11.3.6 Power domains  
The processor has a single power domain. Therefore, it does not support the Event Catch  
Register, the OS Lock, or the OS Save and Restore functionality.  
11.3.7 Effects of resets on debug registers  
The processor has two reset signals which affect the debug registers in the following ways:  
nSYSPORESET  
You must assert this signal when powering up to set the non-debug processor  
logic to a known state.  
PRESETDBGn  
You can assert this signal to set all of the debug logic to a known state, without  
affecting the state of the remainder of the processor logic.  
11.3.8 APB port access permissions  
The restrictions for accessing the APB slave port are described as follows:  
Privilege of memory access  
You must configure the system to disable accesses to the memory-mapped  
registers based on the privilege of the memory access.  
Power down  
The processor only supports a single power domain, therefore you must configure  
the system to return an error response to all accesses made to the APB interface  
while the processor is powered-down.  
Privilege of memory access permission  
When non-privileged software attempts to access the APB slave port, the system must ignore  
the access or generate an error response to the access. You must implement this restriction at the  
system level because the APB protocol does not have a privileged or user control signal. You  
can choose to have the system either ignore the access or generate an error response.  
You can place additional restrictions on memory transactions that are permitted to access the  
APB port. However, ARM does not recommend this.  
Locks permission  
You can lock the APB slave port so that access to some debug registers is restricted. ARM  
Architecture v7 defines two locks:  
Software lock  
The external debugger can set this lock to prevent software from modifying the  
debug registers settings. A debug monitor can also set this lock prior to returning  
control to the application to reduce the chance of erratic code changing the debug  
settings. When this lock is set, writes to all debug registers are ignored, except  
those generated by the external debugger, which override the lock. For more  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-8  
     
Debug  
OS Lock  
Note  
The processor does not support OS Lock.  
These locks are set to their reset values only on reset of the debug logic, provided by  
PRESETDBGn.  
You must set the PADDRDBG31 input signal to 1 for accesses originated from the  
external debugger for the Software Lock override feature to work.  
Table 11-4 External debug interface access permissions  
Registers  
PADDRDBG31 Lock  
DRCR, PRCR, PRSR Other Debug registers LAR  
Other registers  
Xa  
Xa  
1d  
0
NPOSSb  
OKc  
NPOSSb  
OKc  
NPOSSb NPOSSb  
X
1
OKc  
OKc  
OKc  
OKc  
WIe  
OKc  
WIe  
WIe  
0
OKc  
OKc  
0
a. X indicates that the outcome does not depend on this condition.  
b. Not possible. Accessing debug registers while the processor is powered down is not possible.  
c. OK indicates that the access succeeds.  
d. LSR[1] bit is set.  
e. WI indicates that writes are ignored.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-9  
 
Debug  
11.4 Debug register descriptions  
Table 11-5 shows definitions of terms used in the register descriptions.  
Table 11-5 Terms used in register descriptions  
Term Description  
R
Read-only. Written values are ignored.  
W
Write-only. This bit cannot be read. Reads return an Unpredictable value.  
Read or write.  
RW  
RAZ  
RAO  
Read-As-Zero. Always zero when read.  
Read-As-One. Always one when read.  
SBZP Should-Be-Zero (SBZ) or Preserved (P). Must be written as 0 or preserved by writing the same value previously  
read from the same fields on the same processor. These bits are usually reserved for future expansion.  
UNP  
A read from this bit returns an Unpredictable value.  
11.4.1 Accessing debug registers  
To access the CP14 debug registers you set Opcode_1 and Opcode_2 to zero. The CRn and CRm  
fields of the coprocessor instructions encode the CP14 debug register number, where the register  
number is {<Opcode2>, <CRm>}. In addition, the CRn field can specify additional registers.  
Table 11-6 shows the CP14 debug register map.  
Table 11-6 CP14 debug register map  
CRn  
Op1 CRm Op2 CP14 debug register name  
Abbreviation Reference  
c0  
0
0
c0  
c0  
0
0
Debug ID Register  
DIDR  
c1  
c2  
Debug ROM Address Register  
DRAR  
CP14 c0, Debug ROM  
Address Register on  
0
c0  
0
Debug Self Address Offset Register DSAR  
CP14 c0, Debug Self  
Address Offset Register on  
c3-c15  
c0  
0
0
c0  
c1  
0
0
Reserved  
-
-
Debug Status and Control Register  
DSCR  
CP14 c1, Debug Status  
and Control Register on  
c1-c15  
c0-c15  
c0  
0
0
0
c1  
0
0
0
Reserved  
-
-
-
c2-c4  
c5  
Reserved  
-
Data Transfer Register  
DTR  
11.4.2 CP14 c0, Debug ID Register  
The DIDR is a read-only register that identifies the debug architecture version and specifies the  
number of debug resources that the processor implements.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-10  
               
Debug  
The Debug ID Register is:  
in CP14 c0  
a 32 bit read-only register  
accessible in User and Privileged modes.  
Figure 11-2 shows the bit arrangement of the DIDR.  
31  
28 27  
24 23  
20 19  
16 15  
8
7
4
3
0
WRP  
BRP  
Context ID  
Reserved  
Variant  
Revision  
Debug architecture  
version  
Figure 11-2 Debug ID Register format  
Table 11-7 shows how the bit values correspond with the Debug ID Register functions.  
Table 11-7 Debug ID Register functions  
Bits  
Field  
Function  
[31:28]  
WRP  
Number of Watchpoint Register Pairs:  
b0000 = 1 WRP  
b0001 = 2 WRPs  
...  
b0111 = 8 WRPs.  
[27: 24] BRP  
Number of Breakpoint Register Pairs:  
b0001 = 2 BRPs  
b0010 = 3 BRPs  
...  
b0111 = 8 BRPs.  
[23:20]  
Context  
Number of Breakpoint Register Pairs with context ID comparison capability:  
b0000 = 1 BRP has context ID comparison capability  
[19:16]  
Debugarchitecture Debug architecture version:  
version  
b0100 denotes ARMv7 Debug.  
[15:8]  
[7: 4]  
Reserved  
Variant  
RAZ.  
Implementation-defined variant number. See Product revision information on page 1-24  
for details of the value of this field.  
[3: 0]  
Revision  
Implementation-defined revision number. See Product revision information on  
page 1-24 for details of the value of this field.  
The values of the following fields of the Debug ID Register agree with the values in CP15 c0,  
Main ID Register:  
DIDR[3:0] is the same as CP15 c0 bits [3:0]  
DIDR[7:4] is the same as CP15 c0 bits [23:20].  
See c0, Main ID Register on page 4-14 for more information of CP15 c0, Main ID Register.  
The reason for duplicating these fields here is that the Debug ID Register is also accessible  
through the APB slave port. This enables an external debugger to determine the variant and  
revision numbers without stopping the processor.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-11  
       
Debug  
To use the Debug ID Register, read CP14 c0 with:  
MRC p14, 0, <Rd>, c0, c0, 0 ; Read Debug ID Register  
11.4.3 CP14 c0, Debug ROM Address Register  
The Debug ROM Address Register is a read-only register that returns a 32-bit Debug ROM  
Address Register value. This is the address that indicates where in memory a debug monitor can  
locate the debug bus ROM specified by the CoreSightmultiprocessor trace and debug  
architecture. This ROM holds information about all the components in the debug bus. You can  
configure the address read in this register during integration using the  
DBGROMADDR[31:12] and DBGROMADDRV inputs. DBGROMADDRV must be tied  
off to 1 if DBGROMADDR[31:12] is tied off to a valid value.  
The Debug ROM Address Register is:  
in CP14 c0, sub-register c1  
a 32 bit read-only register  
accessible in User and Privileged modes.  
Figure 11-3 shows the bit arrangement of the Debug ROM address register.  
31  
12 11  
2
1
0
Debug bus ROM physical address  
Reserved  
Valid bits  
Figure 11-3 Debug ROM Address Register format  
Table 11-8 shows how the bit values correspond with the Debug ROM Address Register  
functions.  
Table 11-8 Debug ROM Address Register functions  
Bits  
Field  
Function  
[31:12] Debug bus  
Indicates bits [31:12] of the debug bus ROM address.  
ROM address.  
Reserved  
Valid bits  
[11: 2]  
[1:0]  
SBZ.  
Indicates that the ROM address is valid.  
Reads b11 if DBGROMADDRV is set to 1, otherwise reads b00. DBGROMADDRV must  
be set to 1 if DBGROMADDR[31:12] is set to a valid value.  
To use the Debug ROM Address Register, read CP14 c0 with:  
MRC p14, 0, <Rd>, c1, c0, 0 ; Read Debug ROM Address Register  
11.4.4 CP14 c0, Debug Self Address Offset Register  
The Debug Self Address Offset Register is a read-only register that returns a 32-bit offset value  
from the Debug ROM Address Register to the address of the processor debug registers. You can  
configure the address read in this register during integration using the  
DBGSELFADDR[31:12] and DBGSELFADDRV inputs. DBGSELFADDRV must be tied  
off to 1 if DBGSELFADDR[31:12] is tied off to a valid value.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-12  
           
Debug  
The Debug Self Address Offset Register is:  
in CP14 c0, sub-register c2  
a 32 bit read-only register  
accessible in User and Privileged modes.  
Figure 11-4 shows the bit arrangement of the Debug Self Address Offset Register.  
31  
12 11  
2
1
0
Debug bus self address offset value  
Reserved  
Valid bits  
Figure 11-4 Debug Self Address Offset Register format  
Table 11-9 shows how the bit values correspond with the Debug Self Address Offset Register  
functions.  
Table 11-9 Debug Self Address Offset Register functions  
Function  
Bits  
Field  
[31:12] Debug bus self  
address offset value  
Indicates bits [31:12] of the two’s complement offset from the debug ROM physical  
address to the physical address where the debug registers are mapped.  
[11: 2]  
[1:0]  
Reserved  
Valid bits  
UNP on reads, SBZP on writes.  
Reads b11 if DBGSELFADDRV is set to 1, otherwise reads b00.  
DBGSELFADDRV must be set to 1 if DBGSELFADDR[31:12] is set to a valid  
value.  
To use the Debug Self Address Offset Register, read CP14 c0 with:  
MRC p14, 0, <Rd>, c2, c0, 0  
; Read Debug Self Address Offset Register  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-13  
       
Debug  
11.4.5 CP14 c1, Debug Status and Control Register  
The DSCR contains status and control information about the debug unit. Figure 11-5 shows the  
bit arrangement of the DSCR.  
31 30 29 28 27 26 25 24 23 22 21 20 19 18  
16 15 14 13 12 11 10 9  
8
7
6
5
2
1
0
MOE  
Core halted  
Core restarted  
Sticky precise abort  
Sticky imprecise abort  
Sticky Undefined  
Reserved  
Reserved  
Discard  
imprecise  
abort  
DTR access  
Reserved  
InstrCompl  
PipeAdv  
DbgAck  
IntDis  
Reserved  
DTRTXfull  
DTRRXfull  
Reserved  
Comms  
ARM  
Halting mode  
Monitor mode  
Figure 11-5 Debug Status and Control Register format  
Table 11-10 shows how the bit values correspond with Debug Status and Control Register  
functions.  
Table 11-10 Debug Status and Control Register functions  
Function  
Bits  
Field  
[31]  
[30]  
Reserved  
RAZ on reads, SBZP on writes.  
DTRRXfull  
The DTRRXfull flag:  
0 = Read-DTR, DTRRX, empty, reset value  
1 = Read-DTR, DTRRX, full.  
When set, this flag indicates to the processor that there is data available to read at the  
DTRRX. It is automatically set on writes to the DTRRX by the debugger, and is cleared  
when the processor reads the CP14 DTR. If the flag is not set, the DTRRX returns an  
Unpredictable value.  
[29]  
DTRTXfull  
The DTRTXfull flag:  
0 = Write-DTR, DTRTX, empty, reset value  
1 = Write-DTR, DTRTX, full.  
When clear, this flag indicates to the processor that the DTRTX is ready to receive data. It  
is automatically cleared on reads of the DTRTX by the debugger, and is set when the  
processor writes to the CP14 DTR. If this bit is set and the processor attempts to write to  
the DTRTX, the register contents are overwritten and the DTRRXfull flag remains set.  
[28:26] Reserved  
[25] PipeAdv  
RAZ on reads, SBZP on writes.  
Sticky pipeline advance read-only bit. This bit enables the debugger to detect whether the  
processor is idle. In some situations, this might mean that the system bus port is  
deadlocked. This bit is set to 1 when the processor pipeline retires one instruction. It is  
cleared by a write to DRCR[3].  
0 = no instruction has completed execution since the last time this bit was cleared  
1 = an instruction has completed execution since the last time this bit was cleared.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-14  
           
Debug  
Table 11-10 Debug Status and Control Register functions (continued)  
Bits  
Field  
Function  
[24]  
InstrCompl  
Instruction complete read-only bit. This flag determines whether the processor has  
completed execution of an instruction issued through the APB port.  
0 = processor is currently executing an instruction fetched from the ITR Register  
1 = processor is not currently executing an instruction fetched from the ITR Register.  
When the APB port reads the DSCR and this bit is clear, then a subsequent write to the  
ITR Register is ignored unless DSCR[21:20] is not equal to 0. If DSCR[21:20] is not equal  
to 0, the ITR write stalls until the processor completes execution of the current instruction.  
If the processor is not in debug state, then the value read for this flag is Unpredictable. The  
flag is set to 1 on entry to debug state.  
[23:22] Reserved  
RAZ on reads, SBZP on writes.  
[21:20] DTR access  
DTR access mode. You can use this field to optimize DTR traffic between a debugger and  
the processor.  
b00 = Non-blocking mode, the default  
b01 = Stall mode  
b10 = Fast mode  
b11 = Reserved.  
Note  
This field only affects the behavior of DSCR, DTR, and ITR accesses through the  
APB port, and not through CP14 debug instructions.  
Non-blocking mode is the default setting. Improper use of the other modes might  
result in the debug access bus becoming deadlocked.  
Discardimprecise The Discard imprecise abort bit is set when the processor is in debug state and is cleared  
[19]  
abort  
on exit from debug state. While this bit is set, the processor does not take imprecise Data  
Aborts. However, the sticky imprecise Data Abort bit is set to 1.  
0 = do not discard imprecise Data Aborts  
1 = discard imprecise Data Aborts.  
[18-16] Reserved  
[15] Monitor mode  
RAZ on reads, SBZP on writes.  
The Monitor debug-mode enable bit:  
0 = Monitor debug-mode disabled, this is the reset value  
1 = Monitor debug-mode enabled.  
If Halting debug-mode is enabled through bit [14], then the processor is in Halting  
debug-mode regardless of the value of bit [15]. If the external interface input DBGEN is  
LOW, this bit reads as 0. The programmed value is masked until DBGEN is HIGH, and  
at that time the read value reverts to the programmed value.  
[14]  
Halting mode  
The Halting debug-mode enable bit:  
0 = Halting debug-mode disabled, this is the reset value  
1 = Halting debug-mode enabled.  
If the external interface input DBGEN is LOW, this bit reads as 0. The programmed value  
is masked until DBGEN is HIGH, and at that time the read value reverts to the  
programmed value.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-15  
Debug  
Table 11-10 Debug Status and Control Register functions (continued)  
Bits  
Field  
Function  
[13]  
ARM  
Execute ARM instruction enable bit:  
0 = disabled, this is the reset value  
1 = enabled.  
If this bit is set and an ITR write succeeds, the processor fetches an instruction from the  
ITR for execution. If this bit is set to 1 when the processor is not in debug state, the  
behavior of the processor is Unpredictable.  
[12]  
[11]  
Comms  
IntDis  
CP14 debug user access disable control bit:  
0 = CP14 debug user access enable, this is the reset value  
1 = CP14 debug user access disable.  
If this bit is set and a User mode process attempts to access any CP14 debug registers, an  
Undefined instruction exception is taken.  
Interrupts disable bit:  
0 = interrupts enabled, this is the reset value  
1 = interrupts disabled.  
If this bit is set, the IRQ and FIQ input signals are inhibited. The external debugger can  
optionally use this bit to execute pieces of code in normal state as part of the debugging  
process to avoid having an interrupt taking control of the program flow. For example, the  
debugger might use this bit to execute an OS service routine to bring a page from disk into  
memory. It might be undesirable to service any interrupt during the routine execution.  
[10]  
DbgAck  
DbgAck bit. If this bit is set to 1, the DBGACK output signal is forced HIGH, regardless  
of the processor state. The external debugger can optionally use this bit to execute pieces  
of code in normal state as part of the debugging process for the system to behave as if the  
processor is in debug state. Some systems rely on DBGACK to determine whether data  
accesses are application or debugger generated. This bit is 0 on reset.  
[9]  
[8]  
Reserved  
RAZ on reads, SBZP on writes.  
Sticky Undefined  
Sticky Undefined bit:  
0 = no Undefined exception occurred in debug state since the last time this bit was cleared  
1 = an Undefined exception occurred while in debug state since the last time this bit was  
cleared.  
This flag detects Undefined exceptions generated by instructions issued to the processor  
through the ITR. This bit is set to 1 when an Undefined instruction exception occurs while  
the processor is in debug state and is cleared by writing a 1 to DRCR[2].  
[7]  
[6]  
Sticky imprecise  
abort  
Sticky imprecise Data Abort bit:  
0 = no imprecise Data Aborts occurred since the last time this bit was cleared  
1 = an imprecise Data Abort occurred since the last time this bit was cleared.  
This flag detects imprecise Data Aborts triggered by instructions issued to the processor  
through the ITR. This bit is set to 1 when an imprecise Data Abort occurs while the  
processor is in debug state and is cleared by writing a 1 to DRCR[2].  
Sticky precise  
abort  
Sticky precise Data Abort bit:  
0 = no precise Data Abort occurred since the last time this bit was cleared  
1 = a precise Data Abort occurred since the last time this bit was cleared.  
This flag detects precise Data Aborts generated by instructions issued to the processor  
through the ITR. This bit is set to 1 when a precise Data Abort occurs while the processor  
is in debug state and is cleared by writing to the DRCR[2].  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-16  
Debug  
Table 11-10 Debug Status and Control Register functions (continued)  
Bits  
Field  
Function  
[5:2]  
MOE  
Method of entry bits:  
b0000 = a DRCR[0] halting debug event occurred  
b0001 = a breakpoint occurred  
b0100 = an EDBGRQ halting debug event occurred  
b0011 = a BKPT instruction occurred  
b1010 = a precise watchpoint occurred  
others = reserved.  
These bits are set to indicate any of:  
the cause of a debug exception  
the cause for entering debug state.  
A Prefetch Abort or Data Abort handler must check the value of the CP15 Fault Status  
Register to determine whether a debug exception occurred and then use these bits to  
determine the specific debug event.  
[1]a  
Core restarted  
Core halted  
Core restarted bit:  
0 = the processor is exiting debug state  
1 = the processor has exited debug state. This is the reset value.  
The debugger can poll this bit to determine when the processor responds to a request to  
leave debug state.  
[0]a  
Core halted bit:  
0 = the processor is in normal state. This is the reset value.  
1 = the processor is in debug state.  
The debugger can poll this bit to determine when the processor has entered debug state.  
a. These bits always reflect the status of the processor, therefore they only have a reset value if the particular reset event affects  
the processor. For example, a PRESETDBGn event leaves these bits unchanged and a processor reset event such as  
nSYSPORESET sets DSCR[18] to a 0 and DSCR[1:0] to 10.  
To use the Debug Status and Control Register, read or write CP14 c1 with:  
MRC p14, 0, <Rd>, c0, c1, 0 ; Read Debug Status and Control Register  
MCR p14, 0, <Rd>, c0, c1, 0 ; Write Debug Status and Control Register  
DTR access mode  
You can use the DTR access mode field to optimize data transfer between a debugger and the  
processor.  
The DTR access mode can be one of the following:  
Nonblocking. This is the default mode.  
Stall.  
Fast.  
In Non-blocking mode, reads from DTRTX and writes to DTRRX and ITR are ignored if the  
appropriate latched ready flag is not in the ready state. These latched flags are updated on DSCR  
reads. The following applies:  
writes to DTRRX are ignored if DTRRXfull_l is set to b1  
reads from DTRTX are ignored, and return an Unpredictable value, if DTRTXfull_l is set  
to b0  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-17  
   
Debug  
writes to ITR are ignored if InstrCompl_l is set to b0  
following a successful write to DTRRX, DTRRXfull and DTRRXfull_l are set to b1  
following a successful read from DTRTX, DTRTXfull and DTRTXfull_l are cleared to b0  
following a successful write to ITR, InstrCompl and InstrCompl_l are cleared to b0.  
Debuggers accessing these registers must first read DSCR. This has the side-effect of copying  
DTRRXfull and DTRTXfull to DTRRXfull_l and DTRTXfull_l. The debugger must then:  
write to the DTRRX if the DTRRXfull flag was b0 (DTRRXfull_l is b0)  
read from the DTRTX if the DTRTXfull flag was b1 (DTRTXfull_l is b1)  
write to the ITR if the InstrCompl_l flag was b1.  
However, debuggers can issue both actions together and later determine from the read DSCR  
value whether the operations were successful.  
In Stall mode, the APB accesses to DTRRX, DTRTX, and ITR stall under the following  
conditions:  
writes to DTRRX are stalled until DTRRXfull is cleared  
writes to ITR are stalled until InstrCompl is set  
reads from DTRTX are stalled until DTRTXfull is set.  
Fast mode is similar to Stall mode except that in Fast mode, the processor fetches an instruction  
from the ITR when a DTRRX write or DTRTX read succeeds. In Stall mode and Nonblocking  
mode, the processor fetches an instruction from the ITR when an ITR write succeeds.  
11.4.6 Data Transfer Register  
The DTR consists of two separate physical registers:  
the DTRRX (Read Data Transfer Register)  
the DTRTX (Write Data Transfer Register).  
The register accessed is dependent on the instruction used:  
writes, MCRand LDCinstructions, access the DTRTX  
reads, MRCand STCinstructions, access the DTRRX.  
Note  
Read and write are used with respect to the processor.  
For information on the use of these registers with the DTRTXfull flag and DTRRXfull flag, see  
Debug communications channel on page 11-55. The Data Transfer Register, bits [31:0] contain  
the data to be transferred.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-18  
 
Debug  
Table 11-11 shows how the bit values correspond with the DTRRX and DTRTX functions.  
Table 11-11 Data Transfer Register functions  
Bits  
Field Function  
Reads the Data Transfer Register. This is read-only for the CP14 interface.  
[31:0] Data  
Note  
Reads of the DTRRX through the coprocessor interface cause the DTRTXfull flag to be cleared.  
However, reads of the DTRRX through the APB port do not affect this flag.  
[31:0] Data  
Writes the Data Transfer Register. This is write-only for the CP14 interface.  
Note  
Writes to the DTRTX through the coprocessor interface cause the DTRRXfull flag to be set.  
However, writes to the DTRTX through the APB port do not affect this flag.  
11.4.7 Watchpoint Fault Address Register  
The Watchpoint Fault Address Register (WFAR) is a read/write register that holds the address  
of the instruction that triggers the watchpoint.  
Figure 11-6 shows the bit arrangement of the Watchpoint Fault Address Register.  
1
31  
0
Address  
Reserved  
Figure 11-6 Watchpoint Fault Address Register format  
Table 11-12 shows how the bit values correspond with the WFAR functions.  
Table 11-12 Watchpoint Fault Address Register functions  
Bits  
Field  
Function  
[31:1] Address  
This is the address of the watchpointed instruction. When a watchpoint occurs in ARM state, the  
WFAR contains the address of the instruction causing it plus an offset of 0x8. When a watchpoint  
occurs in Thumb state, the offset is plus 0x4  
.
[0]  
Reserved RAZ.  
11.4.8 Vector Catch Register  
The processor supports efficient exception vector catching. The read/write Vector Catch  
Register controls this, as Figure 11-7 on page 11-20 shows.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-19  
               
Debug  
31  
8
7
6
5
4
3
2
1
0
Reserved  
Reset  
Reserved  
SVC  
Prefetch abort  
Data abort  
Reserved  
IRQ  
FIQ  
Figure 11-7 Vector Catch Register format  
If one of the bits in this register is set and the instruction at the corresponding vector is  
committed for execution, the processor either enters debug state or takes a debug exception.  
Note  
Under this model, any prefetch from an exception vector can trigger a vector catch, not  
only the ones because of exception entries. An explicit branch to an exception vector  
might generate a vector catch debug event.  
If any of the bits are set when the processor is in Monitor debug-mode, then the processor  
ignores the setting and does not generate a vector catch debug event. This prevents the  
processor entering an unrecoverable state. The debugger must program these bits to zero  
when Monitor debug-mode is selected and enabled to ensure forward-compatibility.  
Table 11-13 shows how the bit values correspond with the Vector Catch Register functions.  
Table 11-13 Vector Catch Register functions  
Reset Normal  
High vectors  
address  
Bits  
Field  
Function  
Access  
value  
address  
[31:8] Reserved  
0
-
-
Do not modify on writes. On reads,  
the value returns zero.  
RAZ or  
SBZP  
[7]  
[6]  
[5]  
FIQ  
0
-
0x0000001C  
0x00000018  
-
0xFFFF001C  
Vector catch enable.  
Vector catch enable.  
RW  
-
a
a
IRQ  
0xFFFF0018  
Reserved  
0
-
Do not modify on writes. On reads,  
the value returns zero.  
RAZ or  
SBZP  
[4]  
[3]  
[2]  
[1]  
Data Abort  
Prefetch Abort  
SVC  
0
0
0
0
0x00000010  
0x0000000C  
0x00000008  
0x00000004  
0xFFFF0010  
0xFFFF000C  
0xFFFF0008  
0xFFFF0004  
Vector catch enable.  
Vector catch enable.  
Vector catch enable.  
RW  
RW  
RW  
RW  
Reserved  
Vector catch enable, Undefined  
instruction.  
[0]  
Reset  
0
0x00000000  
0xFFFF0000  
Vector catch enable.  
RW  
a. If the VIC interface is enabled, the address is the last IRQ handler address supplied by the VIC, whether or not high vectors  
are in use.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-20  
         
Debug  
11.4.9 Debug State Cache Control Register  
The DSCCR controls the L1 cache behavior when the processor is in debug state.  
Figure 11-8 shows the bit arrangement of the DSCCR.  
31  
3
2
1
0
Reserved  
Not write-through  
Instruction cache line-fill  
Data cache line-fill  
Figure 11-8 Debug State Cache Control Register format  
For information on the usage model of the DSCCR register, see Cache debug on page 11-50.  
Table 11-14 shows how the bit values correspond with the Debug State Cache Control Register  
functions.  
Table 11-14 Debug State Cache Control Register functions  
Reset  
Bits  
Field  
Description  
value  
[31:3] Reserved  
0
0
Reserved. Do not modify on writes. On reads, the value returns zero.  
[2]  
nWT  
Not write-through:  
1 = normal operation of regions marked as write-back in debug state  
0 = force write-through behavior for regions marked as write-back in debug state, this is  
the reset value.  
[1]  
[0]  
nIL  
0
0
Instruction cache line-fill:  
1 = normal operation of L1 instruction cache in debug state  
0 = L1 instruction cache line-fills disabled in debug state, this is the reset value.  
nDL  
Data cache line-fill:  
1 = normal operation of L1 data cache in debug state  
0 = L1 data cache line-fills disabled in debug state, this is the reset value.  
11.4.10 Instruction Transfer Register  
The ITR enables the external debugger to feed instructions into the processor for execution  
while in debug state. The ITR is a write-only register. Reads from the ITR return an  
Unpredictable value.  
The Instruction Transfer Register, bits [31:0] contain the ARM instruction for the processor to  
execute while in debug state. The reset value of this register is Unpredictable.  
Note  
Writes to the ITR when the processor is not in debug state or the DSCR[13] execute instruction  
enable bit is cleared are Unpredictable. When an instruction is issued to the processor, the debug  
unit prevents the next instruction from being issued until the DSCR[25] instruction complete bit  
is set.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-21  
           
Debug  
11.4.11 Debug Run Control Register  
The DRCR requests the processor to enter or leave debug state. It also clears the sticky  
exception bits present in the DSCR.  
Figure 11-9 shows the bit arrangement of the DRCR.  
31  
5
4
3
2
1
0
Reserved  
Cancel memory request  
Clear sticky pipeline advance  
Clear sticky exceptions  
Restart request  
Halt request  
Figure 11-9 Debug Run Control Register format  
Table 11-15 shows how the bit values correspond with the Debug Run Control Register  
functions.  
Table 11-15 Debug Run Control Register functions  
Function  
Bits  
Field  
[31:5] Reserved  
RAZ.  
[4]  
Cancel memory  
requests  
If 1 is written to this bit, the processor abandons any pending memory transactions until it  
can enter debug state. Debug state entry is the acknowledge event that clears this request.  
Abandoned transactions have the following behavior:  
abandoned stores might write an Unpredictable value to the target address  
abandoned loads return an Unpredictable value to the register bank.  
An abandoned transaction does not cause any exception. Additional instruction fetches or  
data accesses after the processor entered debug state have an Unpredictable behavior.  
This bit enables the debugger to progress on a deadlock so the processor can enter debug  
state. For a debug state entry to occur, a halting debug event must be requested before this  
bit is set. If you write a 1 to this bit when DBGEN is LOW, the write has no effect.a  
[3]  
[2]  
[1]  
Clear sticky  
pipeline advance  
Writing a 1 to this bit clears DSCR[25].  
Clear sticky  
exceptions  
Writing a 1 to this bit clears DSCR[8:6].  
Restart request  
Halt request  
Writing a 1 to this bit requests that the processor leaves debug state. This request is held  
until the processor exits debug state. When the debugger makes this request, it polls  
DSCR[1] until it reads 1. This bit always reads as zero. Writes are ignored when the  
processor is not in debug state.  
[0]  
Writing a 1 to this bit triggers a halting debug event, that is, a request that the processor  
enters debug state. This request is held until the debug state entry occurs. When the  
debugger makes this request, it polls DSCR[0] until it reads 1. This bit always reads as zero.  
Writes are ignored when the processor is already in debug state.  
a. Entry into debug state is not expected to be recoverable.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-22  
         
Debug  
11.4.12 Breakpoint Value Registers  
Each BVR is associated with a Breakpoint Control Register (BCR). BCRy is the corresponding  
control register for BVRy.  
A pair of breakpoint registers, BVRy/BCRy, is called a Breakpoint Register Pair (BRP).  
BVR0-7 are paired with BCR0-7 to make BRP0-7.  
The breakpoint value contained in this register corresponds to either an instruction address or a  
context ID. Breakpoints can be set on:  
an instruction address  
a context ID value  
an instruction address and context ID pair.  
For an instruction address and context ID pair, two BRPs must be linked. A debug event is  
generated when both the instruction address and the context ID pair match at the same time.  
Table 11-16 shows how the bit values correspond with the Breakpoint Value Registers  
functions.  
Table 11-16 Breakpoint Value Registers functions  
Bits  
Reset value Description  
0x0 Breakpoint value  
[31:0]  
Note  
Only BRPn supports context ID comparison, where n+1 is the number of breakpoint  
register pairs implemented in the processor.  
Bits [1:0] of Registers BVR0 to BVR(n-1) are Do Not Modify on writes and  
Read-As-Zero because these registers do not support context ID comparisons.  
The contents of the CP15 Context ID Register give the context ID value for a BVR to  
match. For information on the Context ID Register, see Chapter 4 System Control  
11.4.13 Breakpoint Control Registers  
The BCR is a read/write register that contains the necessary control bits for setting:  
breakpoints  
linked breakpoints.  
Figure 11-10 shows the bit arrangement of the BCRs.  
31  
29 28  
24 23 22  
20 19  
16 15 14 13  
9
8
5
4
3
2
1
0
Byte  
address  
select  
Breakpoint  
M
Linked BRP  
Reserved  
S
B
address mask  
Reserved  
Reserved  
Secure state access control  
Reserved  
Figure 11-10 Breakpoint Control Registers format  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-23  
           
Debug  
Table 11-17 shows how the bit values correspond with the Breakpoint Control Registers  
functions.  
Table 11-17 Breakpoint Control Registers functions  
Bits  
Field  
Function  
[31:29] Reserved  
Do not modify on writes. On reads, the value returns zero.  
[28:24] Breakpoint  
address mask  
This field sets a breakpoint on a range of addresses by masking lower order address bits out  
of the breakpoint comparison.a  
b00000 = no mask  
b00001 = Reserved  
b00010 = Reserved  
b00011 = 0x00000007mask for instruction address  
b00100 = 0x0000000Fmask for instruction address  
b00101 = 0x0000001Fmask for instruction address  
...  
b11111 = 0x7FFFFFFFmask for instruction address.  
[23]  
Reserved  
M
-
[22:20]  
Meaning of BVR:  
b000 = instruction address match  
b001 = linked instruction address match  
b010 = unlinked context ID  
b011 = linked context ID  
b100 = instruction address mismatch  
b101 = linked instruction address mismatch  
b11x = Reserved.  
For more information, see Table 11-18 on page 11-25  
[19:16] Linked BRP  
number  
The binary number encoded here indicates another BRP to link this one with.  
Note  
if a BRP is linked with itself, it is Unpredictable whether a breakpoint debug event is  
generated  
if this BRP is linked to another BRP that is not configured for linked context ID  
matching, it is Unpredictable whether a breakpoint debug event is generated.  
[15:14] Secure state  
access control  
RAZ or SBZP.  
[13:9]  
Reserved  
Do not modify on writes. On reads, the value returns zero.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-24  
   
Debug  
Table 11-17 Breakpoint Control Registers functions (continued)  
Bits  
Field  
Function  
[8:5]  
Byte address  
select  
For breakpoints programmed to match an instruction address, the debugger must write a  
word-aligned address to the BVR. You can then use this field to program the breakpoint so  
it hits only if certain byte addresses are accessed.b  
If the BRP is programmed for instruction address match:  
b0000 = the breakpoint never hits  
bxxx1 = the breakpoint hits if the byte at address (BVR & 0xFFFFFFFC) +0 is accessed  
bxx1x = the breakpoint hits if the byte at address (BVR & 0xFFFFFFFC) +1 is accessed  
bx1xx = the breakpoint hits if the byte at address (BVR & 0xFFFFFFFC) +2 is accessed  
b1xxx = the breakpoint hits if the byte at address (BVR & 0xFFFFFFFC) +3 is accessed  
b1111 = the breakpoint hits if any of the four bytes starting at address (BVR & 0xFFFFFFFC  
)
+0 is accessed.  
If the BRP is programmed for instruction address mismatch, the breakpoint hits where the  
corresponding instruction address breakpoint does not hit, that is, the range of addresses  
covered by an instruction address mismatch breakpoint is the negative image of the  
corresponding instruction address breakpoint.  
If the BRP is programmed for context ID comparison, this field must be set to b1111.  
Otherwise, breakpoint and watchpoint debug events might not be generated as expected.  
[4:3]  
[2:1]  
Reserved  
S
-
Supervisor access control. The breakpoint can be conditioned on the mode of the processor:  
b00 = User, System, or Supervisor  
b01 = Privileged  
b10 = User  
b11 = any.  
[0]  
B
Breakpoint enable:  
0 = Breakpoint disabled. This is the reset value.  
1 = Breakpoint enabled.  
a. If BCR[28:24] is not set to b00000, then BCR[8:5] must be set to b1111. Otherwise the behavior is Unpredictable. In addition,  
if BCR[28:24] is not set to b00000, then the corresponding BVR bits that are not being included in the comparison Should Be  
Zero. Otherwise the behavior is Unpredictable. If this BRP is programmed for context ID comparison, this field must be set  
to b00000. Otherwise the behavior is Unpredictable. There is no encoding for a full 32-bit mask but the same effect of a break  
anywhere breakpoint can be achieved by setting BCR[22] to 1 and BCR[8:5] to b0000.  
b. Writing a value to BCR[8:5] so that BCR[8] is not equal to BCR[7] or BCR[6] is not equal to BCR[5] has Unpredictable  
results.  
Table 11-18 Meaning of BVR bits [22:20]  
BVR[22:20] Meaning  
b000  
b001  
b010  
The corresponding BVR[31:2] is compared against the instruction address bus and the state of the  
processor against this BCR. It generates a breakpoint debug event on a joint instruction address and state  
match.  
The corresponding BVR[31:2] is compared against the instruction address bus and the state of the  
processor against this BCR. This BRP is linked with the one indicated by BCR[19:16] linked BRP field.  
They generate a breakpoint debug event on a joint instruction address, context ID, and state match.  
The corresponding BVR[31:0] is compared against CP15 Context ID Register, c13 and the state of the  
processor against this BCR. This BRP is not linked with any other one. It generates a breakpoint debug  
event on a joint context ID and state match. For this BRP, BCR[8:5] must be set to b1111. Otherwise it  
is Unpredictable whether a breakpoint debug event is generated.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-25  
 
Debug  
Table 11-18 Meaning of BVR bits [22:20] (continued)  
BVR[22:20] Meaning  
b011  
The corresponding BVR[31:0] is compared against CP15 Context ID Register, c13. This BRP links  
another BRP (of the BCR[21:20]=b01 type), or WRP (with WCR[20]=b1). They generate a breakpoint  
or watchpoint debug event on a joint instruction address or data address and context ID match. For this  
BRP, BCR[8:5] must be set to b1111, BCR[15:14] must be set to b00, and BCR[2:1] must be set to b11.  
Otherwise it is Unpredictable whether a breakpoint debug event is generated.  
b100  
b101  
The corresponding BVR[31:2] and BCR[8:5] are compared against the instruction address bus and the  
state of the processor against this BCR. It generates a breakpoint debug event on a joint instruction  
address mismatch and state match.  
The corresponding BVR[31:2] and BCR[8:5] are compared against the instruction address bus and the  
state of the processor against this BCR. This BRP is linked with the one indicated by BCR[19:16] linked  
BRP field. It generates a breakpoint debug event on a joint instruction address mismatch, state and  
context ID match.  
b11x  
Reserved. The behavior is Unpredictable.  
11.4.14 Watchpoint Value Registers  
Each WVR is associated with a Watchpoint Control Register (WCR). WCRy is the  
corresponding register for WVRy.  
A pair of watchpoint registers, WVRy and WCRy, is called a Watchpoint Register Pair (WRP).  
WVR0-7 are paired with WCR0-7 to make WRP0-7.  
The watchpoint value contained in the WVR always corresponds to a data address and can be  
set either on:  
a data address  
a data address and context ID pair.  
For a data address and context ID pair, a WRP and a BRP with context ID comparison capability  
must be linked. A debug event is generated when both the data address and the context ID pair  
match simultaneously. Table 11-19 shows the bit field definitions for the Watchpoint Value  
Registers.  
Table 11-19 Watchpoint Value Registers functions  
Bits  
[31:2] Watchpoint address.  
[1:0] Reserved. Do not modify on writes. On reads, the value returns zero.  
Description  
11.4.15 Watchpoint Control Registers  
The WCRs contain the necessary control bits for setting:  
watchpoints  
linked watchpoints.  
Figure 11-11 on page 11-27 shows the bit arrangement of the Watchpoint Control Registers.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-26  
       
Debug  
31  
29 28  
24 23  
21 20 19  
16 15 14 13 12  
5
4
3 2 1 0  
Watchpoint  
address mask  
E Linked BRP  
Byte address select  
Reserved  
L/SS
W
Reserved  
Reserved  
Secure state access control  
Figure 11-11 Watchpoint Control Registers format  
Table 11-20 shows how the bit values correspond with the Watchpoint Control Registers  
functions.  
Table 11-20 Watchpoint Control Registers functions  
Function  
Bits  
Field  
[31:29] Reserved  
Do not modify on writes. On reads, the value returns zero.  
[28:24] Watchpoint  
address  
This field watches a range of addresses by masking lower order address bits out of the  
watchpoint comparison.  
mask  
b00000 = no mask  
b00001 = Reserved  
b00010 = Reserved  
b00011 = 0x00000007mask for data address  
b00100 = 0x0000000Fmask for data address  
b00101 = 0x0000001Fmask for data address  
...  
b11111 = 0x7FFFFFFFmask for data address.  
Note  
If WCR[28:24] is not set to b00000, then WCR[12:5] must be set to b11111111.  
Otherwise the behavior is Unpredictable.  
If WCR[28:24] is not set to b00000, then the corresponding WVR bits that are not being  
included in the comparison Should Be Zero. Otherwise the behavior is Unpredictable.  
To watch for a write to any byte in an 8-byte aligned object of size 8 bytes, ARM  
recommends that a debugger sets WCR[28:24] to b00111, and WCR[12:5] to b11111111.  
This is compatible with both ARMv7 debug compliant implementations that have an  
8-bit WCR[12:5] and with those that have a 4-bit WCR[8:5] byte address select field.  
[23:21] Reserved  
Do not modify on writes. On reads, the value returns zero.  
[20]  
E
Enable linking bit:  
0 = linking disabled  
1 = linking enabled.  
When this bit is set, this watchpoint is linked with the context ID holding BRP selected by the  
linked BRP field.  
[19:16] Linked  
BRP  
Linked BRP number. The binary number encoded here indicates a context ID holding BRP to  
link this WRP with. If this WRP is linked to a BRP that is not configured for linked context ID  
matching, it is Unpredictable whether a watchpoint debug event is generated.  
[15:14] Securestate RAZ or SBZP.  
access  
control  
[13]  
Reserved  
Appear as zero when read. Do not modify on writes.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-27  
       
Debug  
Table 11-20 Watchpoint Control Registers functions (continued)  
Bits  
Field  
Function  
[12:5]  
Byte  
address  
select  
The WVR is programmed with word-aligned address. You can use this field to program the  
watchpoint so it only hits if certain byte addresses are accessed:  
b00000000  
bxxxxxxx1  
The watchpoint never hits.  
The watchpoint hits if the byte at address (WVR[31:0] & 0xFFFFFFFC) +0 is  
accessed.  
bxxxxxx1x  
bxxxxx1xx  
bxxxx1xxx  
bxxx1xxxx  
bxx1xxxxx  
bx1xxxxxx  
b1xxxxxxx  
The watchpoint hits if the byte at address (WVR[31:0] & 0xFFFFFFFC) +1 is  
accessed.  
The watchpoint hits if the byte at address (WVR[31:0] & 0xFFFFFFFC) +2 is  
accessed.  
The watchpoint hits if the byte at address (WVR[31:0] & 0xFFFFFFFC) +3 is  
accessed.  
The watchpoint hits if the byte at address (WVR[31:0] & 0xFFFFFFF8) +4 is  
accessed.  
The watchpoint hits if the byte at address (WVR[31:0] & 0xFFFFFFF8) +5 is  
accessed.  
The watchpoint hits if the byte at address (WVR[31:0] & 0xFFFFFFF8) +6 is  
accessed.  
The watchpoint hits if the byte at address (WVR[31:0] & 0xFFFFFFF8) +7 is  
accessed.  
[4:3]  
L/S  
Load/store access. The watchpoint can be conditioned to the type of access:  
b00 = Reserved  
b01 = load, load exclusive, or swap  
b10 = store, store exclusive or swap  
b11 = either.  
A
SWPor SWPBtriggers on load, store, or either. A load exclusive instruction triggers on load or  
either. A store exclusive instruction triggers on store or either, whether it succeeds or not.  
[2:1]  
S
Privileged access control. The watchpoint can be conditioned to the privilege of the access:  
b00 = reserved  
b01 = Privileged, match if the processor does a privileged access to memory  
b10 = User, match only on non-privileged accesses  
b11 = either, match all accesses.  
Note  
For all cases, the match refers to the privilege of the access, not the mode of the processor.  
[0]  
W
Watchpoint enable:  
0 = Watchpoint disabled. This is the reset value.  
1 = Watchpoint enabled.  
11.4.16 Operating System Lock Status Register  
The Operating System Lock Status Register (OSLSR) contains status information about the  
locked debug registers.  
Figure 11-12 on page 11-29 shows the bit arrangement of the OSLSR.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-28  
 
Debug  
31  
1
0
Reserved  
Lock implemented bit  
Figure 11-12 OS Lock Status Register format  
Table 11-21 shows how the bit values correspond with the OS Lock Status Register functions.  
Table 11-21 OS Lock Status Register functions  
Bits  
Field  
Function  
[31:1] Reserved  
RAZ.  
[0]  
Lock implemented bit  
Indicates that the OS lock functionality is not implemented. This bit always reads 0.  
11.4.17 Authentication Status Register  
The Authentication Status Register is a read-only register that reads the current values of the  
configuration inputs that determine the debug permission level.  
Figure 11-13 shows the bit arrangement of the Authentication Status Register.  
31  
8
7
6
5
4
3
0
Reserved  
Secure non-invasive debug features implemented  
Secure non-invasive debug features enabled  
Secure invasive debug features implemented  
Secure invasive debug features enabled  
Non-secure debug features  
Figure 11-13 Authentication Status Register format  
Table 11-22 shows how the bit values correspond with the Authentication Status Register  
functions.  
Table 11-22 Authentication Status Register bit functions  
Bits  
Field  
Value  
Function  
[31:8] Reserved  
-
RAZ  
[7]  
Secure non-invasive debug  
0b1  
Implemented  
features implemented  
[6]  
Secure non-invasive debug  
features enabled  
DBGEN || NIDEN Non-invasive debug enable field  
0b1  
[5]  
Secure invasive debug  
features implemented  
Implemented  
[4]  
Secure invasive debug  
features enabled  
DBGEN  
Invasive debug enable field  
Not implemented  
Non-secure debug featuresa  
0x0  
[3:0]  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-29  
                 
Debug  
a. Cortex-R4 does not implement the Security Extensions, so all the debug features are considered  
secure.  
11.4.18 Device Power-down and Reset Control Register  
The PRCR is a read/write register that controls reset and power-down related functionality.  
Figure 11-14 shows the bit arrangement of the PRCR.  
31  
3
2
1
0
Reserved  
Hold internal reset  
Force internal reset  
No Power-down  
Figure 11-14 PRCR format  
Table 11-23 shows how the bit values correspond with the Device Power down and Reset  
Control Register functions.  
Table 11-23 PRCR functions  
Bits  
Field  
Function  
[31:3] Reserved  
Do not modify on writes. On reads, the value returns zero.  
[2]  
Hold internal  
reset  
Hold internal reset bit. This bit can be used to prevent the processor from running again before  
the debugger detects a power-down event and restores the state of the debug registers in the  
processor. This bit does not have any effect on initial system power-up as nSYSPORESET  
clears it.  
0 = Do not hold internal reset on power-up or warm reset. This is the reset value.  
1 = Hold the processor non-debug logic in reset on warm reset until this flag is cleared.  
[1]  
[0]  
Force  
internal reset  
When a 1 is written to this bit, the processor asserts the DBGRSTREQ output for four cycles.  
You can connect this output to an external reset controller which, in turn, resets the processor.  
No  
When set to 1, the DBGNOPWRDWN output signal is HIGH. This output connects to the  
system power controller and is interpreted as a request to operate in emulate mode. In this mode,  
the processor is not actually powered down when requested by software or hardware  
handshakes. This mode is useful when debugging applications on top of working operating  
systems.  
power-down  
0 = DBGNOPWRDWN is LOW. This is the reset value  
1 = DBGNOPWRDWN is HIGH.  
11.4.19 Device Power-down and Reset Status Register  
The PRSR is a read-only register that provides information about the reset and power-down  
state of the processor.  
Figure 11-15 on page 11-31 shows the bit arrangement of the PRSR.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-30  
           
Debug  
31  
4
3
2
1
0
Reserved  
Sticky reset status  
Reset status  
Sticky power-down status  
Power-down status  
Figure 11-15 PRSR format  
Table 11-24 shows how the bit values correspond with the PRSR functions.  
Table 11-24 PRSR functions  
Bits  
Field  
Function  
[31:4] Reserved  
Do not modify on writes. On reads, the value returns zero.  
Sticky reset status bit. This bit is cleared on read.  
[3]  
[2]  
Sticky reset status  
0 = the processor has not been reset since the last time this register was read. This  
is the reset value.  
1 = the processor has been reset since the last time this register was read.  
This sticky bit is set to 1 when nSYSPORESET is asserted.  
Reset status  
Reset status bit:  
0 = the processor is not currently held in reset  
1 = the processor is currently held in reset.  
This bit reads 1 when nSYSPORESET is asserted.  
[1]  
[0]  
Sticky power-down status  
Power-down status  
Reserved. Always zero.  
Reserved. Always one.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-31  
       
Debug  
11.5 Management registers  
The Management Registers define the standardized set of registers that all CoreSight  
components implement. This section describes these registers.  
Table 11-25 shows the contents of the Management Registers for the processor debug unit.  
Table 11-25 Management Registers  
Offset  
(hex)  
Register  
number  
Access Mnemonic  
Description  
0xD00-0xDFC  
0xF00  
832-895  
960  
R
-
Processor Identifier Registers. See Processor ID Registers.  
RW  
ITCTRL  
Integration Mode Control Registers. See Integration Mode  
0xFA0  
0xFA4  
0xFB0  
0xFB4  
0xFB8  
1000  
1001  
1004  
1005  
1006  
CLAIMSET  
CLAIMCLR  
Claim Tag Set Register. See Claim Tag Set Register on  
Claim Tag Clear Register. See Claim Tag Clear Register on  
W
R
LOCKACCESS Lock Access Register. See Lock Access Register on  
LOCKSTATUS  
AUTHSTATUS  
Lock Status Register. See Lock Status Register on  
R
Authentication Status Register. See Authentication Status  
0xFB8-0xFC4  
0xFC8  
1006-1009  
1010  
R
R
R
-
Reserved.  
DEVID  
Device Identifier. Reserved.  
0xFCC  
1011  
DEVTYPE  
Device Type Register. See Device Type Register on  
0xFD0-0xFFC  
1012-1023  
R
-
Identification Registers. See Debug Identification  
11.5.1 Processor ID Registers  
The Processor ID Registers are read-only registers that return the same values as the  
corresponding CP15 Main ID Register and Feature ID Registers. See Chapter 4 System Control  
Coprocessor for details about the information contained in these registers.  
Table 11-26 shows the offset value, register number, mnemonic, and description that are  
associated with each Process ID Register.  
Table 11-26 Processor Identifier Registers  
Offset (hex) Register number Mnemonic  
Function  
0xD00  
0xD04  
0xD08  
0xD0C  
832  
833  
834  
835  
MIDR  
CTR  
TCMTR  
-
Main ID Register  
Cache Type Register  
TCM Type Register  
Alias of MIDR  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-32  
               
Debug  
Table 11-26 Processor Identifier Registers (continued)  
Offset (hex) Register number Mnemonic  
Function  
0xD10  
0xD14  
0xD18-0xD1C  
0xD20  
0xD24  
0xD28  
0xD2C  
0xD30  
0xD34  
0xD38  
0xD3C  
0xD40  
0xD44  
0xD48  
0xD4C  
0xD50  
0xD54  
836  
837  
838-839  
840  
841  
842  
843  
844  
845  
846  
847  
848  
849  
850  
851  
852  
853  
MPUIR  
MPIDR  
-
MPU Type Register  
Multiprocessor Affinity Register  
Alias of MIDR  
ID_PFR0  
ID_PFR1  
ID_DFR0  
ID_AFR0  
Processor Feature Register 0  
Processor Feature Register 1  
Debug Feature Register 0  
Auxiliary Feature Register 0  
ID_MMFR0 Processor Feature Register 0  
ID_MMFR1 Processor Feature Register 1  
ID_MMFR2 Processor Feature Register 2  
ID_MMFR3 Processor Feature Register 3  
ID_ISAR0  
ID_ISAR1  
ID_ISAR2  
ID_ISAR3  
ID_ISAR4  
ID_ISAR5  
ISA Feature Register 0  
ISA Feature Register 1  
ISA Feature Register 2  
ISA Feature Register 3  
ISA Feature Register 4  
ISA Feature Register 5  
11.5.2 Claim Registers  
The Claim Tag Set Register and the Claim Tag Clear Register enable an external debugger to  
claim debug resources.  
Claim Tag Set Register  
Figure 11-16 shows the bit arrangement of the Claim Tag Set Register.  
31  
8 7  
0
Reserved  
Claim tag set  
Figure 11-16 Claim Tag Set Register format  
Table 11-27 shows how the bit values correspond with the Claim Tag Set Register functions.  
Table 11-27 Claim Tag Set Register functions  
Bits  
Field  
Function  
[31:8] Reserved  
[7:0]  
RAZ or SBZP.  
Claim tag set RAO. Sets claim tags on writes.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-33  
         
Debug  
Writing b1 to a specific claim tag set bit sets that claim tag. Writing b0 to a specific claim tag  
bit has no effect. This register always reads 0xFF, indicating eight claim tags are implemented.  
Claim Tag Clear Register  
Figure 11-16 on page 11-33 shows the bit arrangement of the Claim Tag Set Register.  
31  
8 7  
0
Reserved  
Claim tag clear  
Figure 11-17 Claim Tag Clear Register format  
Table 11-28 shows how the bit values correspond with the Claim Tag Clear Register functions.  
Table 11-28 Functional bits of the Claim Tag Clear Register  
Bit  
[31:8] Reserved  
[7:0]  
Field  
Description  
RAZ or SBZP.  
Claim tag clear R/W. Reset value is 0x00  
.
Writing b1 to a specific claim tag clear bit clears that claim tag. Writing b0 has no effect.  
Reading this register returns the current claim tag value.  
11.5.3 Lock Access Register  
The Lock Access Register is a write-only register that controls writes to the debug registers. The  
purpose of the Lock Access Register is to reduce the risk of accidental corruption to the contents  
of the debug registers. It does not prevent all accidental or malicious damage. Because the state  
of the Lock Access Register is in the debug power domain, it is not lost when the processor  
powers down.  
The Lock Access Register, bits [31:0] contain a key which controls the lock status. To unlock  
the debug registers, write a 0xC5ACCE55key to this register. To lock the debug registers, write any  
other value. Accesses to locked debug registers are ignored. The lock is set on reset.  
11.5.4 Lock Status Register  
The Lock Status Register is a read-only register that returns the current lock status of the debug  
registers.  
Figure 11-18 shows the bit arrangement of the Lock Status Register.  
31  
3
2
1
0
Reserved  
32-bit access  
Locked bit  
Lock implemented bit  
Figure 11-18 Lock Status Register format  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-34  
               
Debug  
Table 11-29 shows how the bit values correspond with the Lock Status Register functions.  
Table 11-29 Lock Status Register functions  
Bits  
Field  
Function  
[31:3] Reserved  
Do not modify on writes. On reads, the value returns zero.  
[2]  
[1]  
32-bit access  
Indicates that a 32-bit access is required to write the key to the Lock Access Register.  
This bit always reads 0.  
Locked bit  
Locked bit:  
0 = Writes are permitted.  
1 = Writes are ignored. This is the reset value.  
[0]  
Lock implemented bit Indicates that the OS lock functionality is implemented. This bit always reads 1.  
11.5.5 Device Type Register  
The Device Type Register is a read-only register that indicates the type of debug component.  
Figure 11-19 shows the bit arrangement of the Device Type Register.  
31  
8
7
4
3
0
Reserved  
Sub type Main class  
Figure 11-19 Device Type Register format  
Table 11-30 shows how the bit values correspond with the Device Type Register functions.  
Table 11-30 Device Type Register functions  
Bits  
Field  
Function  
[31:8] Reserved  
Do not modify on writes. On reads, the value returns zero.  
[7:4]  
[3:0]  
Subtype  
0x1, indicates that the sub-type of the device is processor core.  
Main class 0x5, indicates that the main class of the device is debug logic.  
11.5.6 Debug Identification Registers  
The Debug Identification Registers are read-only registers that consist of the Peripheral  
Identification Registers and the Component Identification Registers. The Peripheral  
Identification Registers provide standard information that all CoreSight components require.  
Only bits [7:0] of each register are used. The remaining bits Read-As-Zero.  
The Component Identification Registers identify the processor as a CoreSight component. Only  
bits [7:0] of each register are used, the remaining bits Read-As-Zero. The values in these  
registers are fixed.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-35  
                 
Debug  
Table 11-31 shows the offset value, register number, and description that are associated with  
each Peripheral Identification Register.  
Table 11-31 Peripheral Identification Registers  
Offset (hex) Register number Function  
0xFD0  
0xFD4  
0xFD8  
0xFDC  
0xFE0  
0xFE4  
0xFE8  
0xFEC  
1012  
1013  
1014  
1015  
1016  
1017  
1018  
1019  
Peripheral Identification Register 4  
Reserved  
Reserved  
Reserved  
Peripheral Identification Register 0  
Peripheral Identification Register 1  
Peripheral Identification Register 2  
Peripheral Identification Register 3  
Table 11-32 shows fields that are in the Peripheral Identification Registers.  
Table 11-32 Fields in the Peripheral Identification Registers  
Field  
Size  
Description  
4KB Count  
4 bits  
Indicates the Log2 of the number of 4KB blocks occupied by the debug device. The processor  
debug registers occupy a single 4KB block, therefore this field is always 0x0  
.
JEP106  
Identity  
Code  
4+7 bits Identifies the designer of the processor. This field consists of a 4-bit continuation code and a  
7-bit identity code. Because the processor is designed by ARM, the continuation code is 0x4  
and the identity code is 0x3B. For more information see JEP106M, Standard Manufacture’s  
Identification Code.  
Part number 12 bits  
Indicates the part number of the processor. The part number for the processor is 0xC14.  
Revision  
RevAnd  
4 bits  
Indicates the major and minor revision of the product. The major revision contains  
functionality changes and the minor revision contains bug fixes for the product. The revision  
number starts at 0x0and increments by 1 at both major and minor revisions. See Product  
revision information on page 1-24 for details of the value of this field.  
4 bits  
4 bits  
Indicates the manufacturer revision number. This number starts at 0x0and increments by the  
integrated circuit manufacturer on metal fixes. For the Cortex-R4 processor, the initial value is  
0x0but this value can be changed by the manufacturer.  
Customer  
modified  
Indicates an endorsed modification to the device. On this processor the value is always 0x0.  
Table 11-33 shows how the bit values correspond with the Peripheral ID Register 0 functions.  
Table 11-33 Peripheral ID Register 0 functions  
Bits  
Value Description  
[31:8]  
[7:0]  
-
Reserved  
0x14  
Indicates bits [7:0] of the Part number for the processor  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-36  
           
Debug  
Table 11-34 shows how the bit values correspond with the Peripheral ID Register 1 functions.  
Table 11-34 Peripheral ID Register 1 functions  
Bits  
Value Description  
[31:8]  
[7:4]  
[3:0]  
-
Reserved  
0xB  
0xC  
Indicates bits [3:0] of the JEDEC JEP106 Identity Code  
Indicates bits [11:8] of the Part number for the processor  
Table 11-35 shows how the bit values correspond with the Peripheral ID Register 2 functions.  
Table 11-35 Peripheral ID Register 2 functions  
Bits  
Value Description  
[31:8]  
[7:4]  
-
-
Reserved.  
Indicates the revision number for the Cortex-R4 processor. See Product revision information on  
page 1-24 for more information.  
[3]  
0x1  
0x3  
This field is always set to 1. It indicates that the processor uses a JEP 106 identity code.  
Indicates bits [6:4] of the JEDEC JEP106 Identity Code.  
[2:0]  
Table 11-36 shows how the bit values correspond with the Peripheral ID Register 3 functions.  
Table 11-36 Peripheral ID Register 3 functions  
Bits  
Value Description  
[31:8]  
[7:4]  
-
Reserved.  
0x0  
Indicates the manufacturer revision number. This value changes based on the metal fixes made by the  
manufacturer.  
[3:0]  
0x0  
Customer modified. See Table 11-32 on page 11-36.  
Table 11-37 shows how the bit values correspond with the Peripheral ID Register 4 functions.  
Table 11-37 Peripheral ID Register 4 functions  
Bits  
Value Description  
[31:8]  
[7:4]  
[3:0]  
-
Reserved.  
0x0  
0x4  
Indicates the number of blocks the debug component occupies. This field is always set to 0.  
Indicates the JEDEC JEP106 continuation code. For the processor, this value is 4.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-37  
               
Debug  
Table 11-38 shows the offset value, register number, and value that are associated with each  
Component Identification Register.  
Table 11-38 Component Identification Registers  
Offset (hex) Register number Value Description  
1020 Component Identification Register 0  
1021  
0xFF0  
0xFF4  
0x0D  
0x90  
Component Identification Register 1  
Component Identification Register 2  
Component Identification Register 3  
0xFF8  
0xFFC  
1022  
1023  
0x05  
0xB1  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-38  
   
Debug  
11.6 Debug events  
A processor responds to a debug event in one of the following ways:  
ignores the debug event  
takes a debug exception  
enters debug state.  
This section describes:  
11.6.1 Software debug event  
A software debug event is any of the following:  
• A watchpoint debug event. This occurs when:  
The data address for a load or store matches the watchpoint value.  
All the conditions of the WCR match.  
The watchpoint is enabled.  
The linked context ID-holding BRP, if any, is enabled and its value matches the  
context ID in CP15 c13. See Chapter 4 System Control Coprocessor.  
The instruction that initiated the memory access is committed for execution.  
Watchpoint debug events are only generated if the instruction passes its condition code.  
A breakpoint debug event. This occurs when:  
An instruction was fetched and the instruction address or the CP15 Context ID  
register c13 matched the breakpoint value.  
At the same time the instruction was fetched, all the conditions of the BCR for  
unlinked context ID breakpoint generation matched the I-side control signals.  
The breakpoint is enabled.  
The instruction is committed for execution. These debug events are generated  
whether the instruction passes or fails its condition code.  
A BKPT debug event. This occurs when a BKPTinstruction is committed for execution.  
BKPTis an unconditional instruction.  
A vector catch debug event. This occurs when:  
An instruction was prefetched and the address matched a vector location address.  
This includes any kind of prefetch, not only the ones because of exception entry.  
At the same time the instruction was fetched, the corresponding bit of the VCR was  
set, that is, the vector catch is enabled.  
The instruction is committed for execution. These debug events are generated  
whether the instruction passes or fails its condition code.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-39  
     
Debug  
11.6.2 Halting debug event  
The debugger or the system can cause the processor to enter into debug state by triggering any  
of the following halting debug events:  
assertion of the EDBGRQ signal, an External Debug Request  
write to the DRCR[0] Halt Request control bit.  
If EDBGRQ is asserted while DBGEN is HIGH but invasive debug is not permitted, the  
devices asserting this signal must hold it until the processor enters debug state, that is, until  
DBGACK is asserted. Otherwise, the behavior of the processor is Unpredictable. For DRCR[0]  
halting debug events, the processor records them internally until it is in a state and mode so that  
they can be taken.  
11.6.3 Behavior of the processor on debug events  
This section describes how the processor behaves on debug events while not in debug state. See  
Debug state on page 11-44 for information on how the processor behaves while in debug state.  
When the processor is in Monitor debug-mode, Prefetch Abort and Data Abort vector catch  
debug events are ignored. All other software debug events generate a debug exception such as  
Data Abort for watchpoints, and Prefetch Abort for anything else.  
When debug is disabled, the BKPTinstruction generates a debug exception, Prefetch Abort. All  
other software debug events are ignored.  
When DBGEN is LOW, debug is disabled regardless of the value of DSCR[15:14].  
Table 11-39 shows the behavior of the processor on debug events.  
Table 11-39 Processor behavior on debug events  
Action on software debug  
event  
Action on halting  
debug event  
DBGEN DSCR[15:14] Debug mode  
0
1
1
1
bxx  
b00  
bx1  
b10  
Debug disabled Ignore or Prefetch Abort (for BKPT  
)
Ignore  
None  
Ignore or Prefetch Abort (for BKPT  
Debug state entry  
)
Debug state entry  
Debug state entry  
Debug state entry  
Halting  
Monitor  
Debug exception  
11.6.4 Debug event priority  
Breakpoint, instruction address or CID match, vector catch, and halting debug events have the  
same priority. If more than one of these events occurs on the same instruction, it is  
Unpredictable which event is taken.  
Breakpoint, instruction address or CID match, vector catch cancel the instruction that they occur  
on, therefore a watchpoint cannot be taken on such an instruction.  
11.6.5 Watchpoint debug events  
A precise watchpoint exception has similar behavior to a precise data abort exception:  
the processor sets R14_abt to the address of the instruction to return to plus 0x08.  
the processor does not complete the watchpointed instruction.  
If the watchpointed access is subject to a precise data abort, then the precise abort takes priority  
over the watchpoint because it is a higher priority exception.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-40  
           
Debug  
11.7 Debug exception  
The processor takes a debug exception when a software debug event occurs while in Monitor  
debug-mode. Prefetch Abort and Data Abort Vector catch debug events are ignored. The debug  
software must carefully program certain debug events to prevent the processor from entering an  
unrecoverable state. If the processor takes a debug exception because of a breakpoint, BKPT, or  
vector catch debug event, the processor performs the following actions:  
sets the DSCR[5:2] method-of-entry bits to indicate that a breakpoint occurred  
sets the CP15 IFSR and IFAR registers as described in Effect of debug exceptions on CP15  
performs the same sequence of actions as in a Prefetch Abort exception by:  
updating the SPSR_abt with the saved CPSR  
changing the CPSR to abort mode and the state indicated by the TE bit with normal  
interrupts and imprecise aborts disabled  
setting R14_abt as for a regular Prefetch Abort exception, that is, this register holds  
the address of the cancelled instruction plus 0x04  
setting the PC to the appropriate Prefetch Abort vector.  
Note  
The Prefetch Abort handler is responsible for checking the IFSR to determine if a debug  
exception or other kind of Prefetch Abort exception caused the exception entry. If the cause is  
a debug exception, the Prefetch Abort handler must branch to the debug monitor. The R14_abt  
register holds the address of the instruction to restart.  
If the processor takes a debug exception because of a watchpoint debug event, the processor  
performs the following actions:  
sets the DSCR[5:2] method-of-entry bits to indicate that a precise watchpoint occurred  
sets the CP15 DFSR, DFAR, and WFAR registers as described in Effect of debug  
performs the same sequence of actions as in a Data Abort exception by:  
updating the SPSR_abt with the saved CPSR  
changing the CPSR to the state indicated by the TE bit with normal interrupts and  
imprecise aborts disabled  
setting R14_abt as a regular Data Abort exception, that is, this register gets the  
address of the cancelled instruction plus 0x08  
setting the PC to the appropriate Data Abort vector.  
Note  
The Data Abort handler must check the DFSR to determine if the exception entry was caused  
by a Debug exception or other kind of Data Abort exception. If the cause is a Debug exception,  
the Data Abort handler must branch to the debug monitor. The R14_abt register holds the  
address of the instruction to restart.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-41  
   
Debug  
Table 11-40 shows the values in the link register after exceptions.  
Table 11-40 Values in link register after exceptions  
Return address (RAa) meaning  
Cause of fault  
ARM  
Thumb  
Breakpoint  
RA+4 RA+4  
RA+8 RA+8  
RA+4 RA+4  
RA+4 RA+4  
RA+4 RA+4  
RA+8 RA+8  
Breakpointed instruction address  
Watchpoint  
Watchpointed instruction address  
BKPTinstruction  
Vector catch  
Prefetch Abort  
Data Abort  
BKPTinstruction address  
Vector address  
Address of the instruction where the execution can resume  
Address of the instruction where the execution can resume  
a. This is the address of the instruction that the processor can execute first on debug exception return. The  
address of the access that hit the watchpoint is in the WFAR.  
The following sections describe:  
11.7.1 Effect of debug exceptions on CP15 registers and WFAR  
The four CP15 registers that record abort information are:  
1.  
2.  
3.  
4.  
Data Fault Address Register (DFAR)  
Instruction Fault Address Register (IFAR)  
Instruction Fault Status Register (IFSR)  
Data Fault Status Register (DFSR).  
For more information on these registers, see Chapter 4 System Control Coprocessor.  
If the processor takes a debug exception because of a watchpoint debug event, the processor  
performs the following actions on these registers:  
it does not change the IFSR or IFAR  
it updates the DFSR with the debug event encoding  
it writes an Unpredictable value to the DFAR  
it updates the WFAR with the address of the instruction that accessed the watchpointed  
address, plus a processor state dependent offset:  
+ 8 for ARM state  
+ 4 for Thumb state.  
If the processor takes a debug exception because of a breakpoint, BKPT, or vector catch debug  
event, the processor performs the following actions on these registers:  
it updates the IFSR with the debug event encoding  
it writes an Unpredictable value to the IFAR  
it does not change the DFSR, DFAR, or WFAR.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-42  
       
Debug  
11.7.2 Avoiding unrecoverable states  
The processor ignores vector catch debug events on the Prefetch or Data Abort vectors while in  
Monitor debug-mode because these events would otherwise put the processor in an  
unrecoverable state.  
The debuggers must avoid other similar cases by following these rules, that apply only if the  
processor is in Monitor debug-mode:  
if BCR[22:20] is set to b010, and unlinked context ID breakpoint is selected, then the  
debugger must program BCR[2:1] for the same breakpoint as stated in this section  
if BCR[22:20] is set to b100 or b101, and instruction address mismatch breakpoint is  
selected, then the debugger must program BCR[2:1] for the same breakpoint as stated in  
this section.  
The debugger must write BCR[2:1] for the same breakpoint as either b00 or b10, that selects  
either match in only USR, SYS, or SVC modes or match in only USR mode, respectively. The  
debugger must not program either b01, that is, match in any Privileged mode, or b11, that is,  
match in any mode.  
You must only request the debugger to write b00 to BCR[2:1] if you know that the abort handler  
does not switch to one of the USR, SYS, or SVC mode before saving the context that might be  
corrupted by a later debug event. You must also be careful about requesting the debugger to set  
a breakpoint or BKPT debug event inside a Prefetch Abort or Data Abort handler, or a  
watchpoint debug event on a data address that any of these handlers might access.  
In general, you must only set breakpoint or BKPT debug events inside an abort handler after it  
saves the abort context. You can avoid breakpoint debug events in abort handlers by setting  
BCR[2:1] as previously described.  
If the code being debugged is not running in a Privileged mode, you can prevent watchpoint  
debug events in abort handlers by setting WCR[2:1] to b10 for match only non-privileged  
accesses.  
Failure to follow these guidelines can lead to debug events occurring before the handler is able  
to save the context of the abort. This causes the corresponding registers to be overwritten, and  
results in Unpredictable software behavior.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-43  
 
Debug  
11.8 Debug state  
The debug state enables an external agent, usually a debugger, to control the processor following  
a debug event. While in debug state, the processor behaves as follows:  
The DSCR[0] core halted bit is set.  
The DBGACK signal is asserted, see DBGACK on page 11-51.  
The DSCR[5:2] method of entry bits are set appropriately.  
The processor is halted. The pipeline is flushed and no instructions are fetched.  
The processor does not change the execution mode. The CPSR is not altered.  
Exceptions are treated as described in Exceptions in debug state on page 11-47.  
Interrupts are ignored.  
New debug events are ignored.  
The following sections describe:  
11.8.1 Entering debug state  
When a debug event occurs while the processor is in Halting debug-mode, it switches to a  
special state called debug state so the debugger can take control. You can configure Halting  
debug-mode by setting DSCR[14].  
If a halting debug event occurs, the processor enters debug state even when Halting debug-mode  
is not configured. While the processor is in debug state, the PC does not increment on instruction  
execution. If the PC is read at any point after the processor has entered debug state, but before  
an explicit PC write, it returns a value as described in Table 11-41, depending on the previous  
state and the type of debug event.  
Table 11-41 shows the read PC value after debug state entry for different debug events.  
Table 11-41 Read PC value after debug state entry  
Return address (RAa) meaning  
Debug event  
ARM  
Thumb  
Breakpoint  
Watchpoint  
RA+8 RA+4  
RA+8 RA+4  
Breakpointed instruction address.  
Address of the instruction where the execution resumes. This  
is several instructions after the one that hit the watchpoint.  
BKPTinstruction  
RA+8 RA+4  
BKPTinstruction address.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-44  
         
Debug  
Table 11-41 Read PC value after debug state entry (continued)  
Return address (RAa) meaning  
Debug event  
ARM  
Thumb  
Vector catch  
RA+8 RA+4  
RA+8 RA+4  
Vector address.  
External debug request signal  
activation  
Address of the instruction where the execution resumes.  
Debug state entry request command RA+8 RA+4  
Address of the instruction where the execution resumes.  
Address of the instruction where the execution resumes.  
Address of the instruction where the execution resumes.  
OS unlock event  
RA+8 RA+4  
RA+8 RA+4  
CTI debug request signal  
a. This is the address of the instruction that the processor can execute first on debug exception return. The address of the  
instruction that hit the watchpoint is in the WFAR.  
11.8.2 Behavior of the PC and CPSR in debug state  
The behavior of the PC and CPSR registers while the processor is in debug state is as follows:  
The PC is frozen on entry to debug state. That is, it does not increment on the execution  
of ARM instructions. However, the processor still updates the PC as a response to  
instructions that explicitly modify the PC.  
If the PC is read after the processor has entered debug state, it returns a value as described  
in Table 11-41 on page 11-44, depending on the previous state and the type of debug  
event.  
If the debugger executes a sequence for writing a certain value to the PC and subsequently  
it forces the processor to restart without any additional write to the PC or CPSR, the  
execution starts at the address corresponding to the written value.  
If the debugger forces the processor to restart without having performed a write to the PC,  
the restart address is Unpredictable.  
If the debugger writes to the CPSR, subsequent reads from the PC return an Unpredictable  
value, and if it forces the processor to restart without having performed a write to the PC,  
the restart address is Unpredictable. However, CPSR reads after a CPSR write return the  
written value.  
If the debugger writes to the PC, subsequent reads from the PC return an Unpredictable  
value.  
If the debugger forces the processor to execute an instruction that writes to the PC and this  
instruction fails its condition codes, the PC is written with an Unpredictable value. That  
is, if the debugger forces the processor to restart, the restart address is Unpredictable.  
Also, if the debugger reads the PC, the read value is Unpredictable.  
While the processor is in debug state, the CPSR does not change unless written to by an  
instruction. In particular, the CPSR IT execution state bits do not change on instruction  
execution. The CPSR IT execution state bits do not have any effects on instruction  
execution.  
If the processor executes a data processing instruction with Rd==R15 and S==0, then  
alu-out[0] must equal the current value of the CPSR T bit, otherwise the processor  
behavior is Unpredictable.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-45  
 
Debug  
11.8.3 Executing instructions in debug state  
In debug state, the processor executes instructions issued through the Instruction Transfer  
Register (ITR). Before the debugger can force the processor to execute any instruction, it must  
enable this feature through DSCR[13].  
While the processor is in debug state, it always decodes instructions from the ITR as per the  
ARM instruction set, regardless of the value of the T and J bits of the CPSR.  
The following restrictions apply to instructions executed through the ITR while in debug state:  
with the exception of branch instructions and instructions that modify the CPSR, the  
processor executes any ARM instruction in the same manner as if it was not in debug state  
the branch instructions  
B
,
BL, BLX(1), and BLX(2)are Unpredictable  
certain instructions that normally update the CPSR are Unpredictable  
instructions that load a value into the PC from memory are Unpredictable.  
11.8.4 Writing to the CPSR in debug state  
The only instruction that can update the CPSR while in debug state is the MSRinstruction. All  
other ARMv7 instructions that write to the CPSR are Unpredictable, that is, the BX  
LDM(3), and data processing instructions with Rd==R15 and S==1.  
,
BXJ, SETEND,  
CPS RFE,  
,
The behavior of the CPSR forms of the MSRand MRSinstructions in debug state is different to their  
behavior in normal state:  
When not in debug state, an MSRinstruction that modifies the execution state bits in the  
CPSR is Unpredictable. However, in debug state an MSR instruction can update the  
execution state bits in the CPSR. An Instruction Synchronization Barrier (ISB) sequence  
must follow a direct modification of the execution state bits in the CPSR by an MSR  
instruction.  
When not in debug state, an MRSinstruction reads the CPSR execution state bits as zeros.  
However, in debug state an MRSinstruction returns the actual values of the execution state.  
The debugger must execute an ISBsequence after it writes to the CPSR execution state bits using  
an MSRinstruction. If the debugger reads the CPSR using an MRSinstruction after a write to any  
of these bits, but before an ISBsequence, the value that MRSreturns is Unpredictable. Similarly,  
if the debugger forces the processor to leave debug state after an MSRwrites to the execution state  
bits, but before any ISBsequence, the behavior of the processor is Unpredictable.  
11.8.5 Privilege  
When the processor is in debug state, ARM instructions issued through the ITR are subject to  
different rules about whether they can perform privileged actions. The general rule is that all  
instructions and operations are permitted in debug state.  
11.8.6 Accessing registers and memory  
The processor always accesses register banks and memory as indicated by the CPSR mode bits,  
in both normal and debug state. For example, if the CPSR mode bits indicate the processor is in  
User mode, ARM register reads and returns the User mode banked registers, and memory  
accesses are presented to the MPU as not privileged.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-46  
       
Debug  
11.8.7 Coprocessor instructions  
CP14 and CP15 instructions can always be executed in debug state regardless of processor  
mode.  
11.8.8 Effect of debug state on non-invasive debug  
The processor non-invasive debug features are the ETM and Performance Monitoring Unit  
(PMU). All of these non-invasive debug features are disabled when the processor is in debug  
When the processor is in debug state:  
the ETM ignores all instructions and data transfers  
PMU events are not counted  
events are not visible to the ETM  
the PMU Cycle Count Register (CCNT) is stopped.  
11.8.9 Effects of debug events on processor registers  
On entry to debug state, the processor does not update any general-purpose or program status  
register. This includes the SPSR_abt and R14_abt registers. In addition, the processor does not  
update any coprocessor registers, including the CP15 IFSR, DFSR, DFAR, or IFAR registers,  
except for CP14 DSCR[5:2] method-of-entry bits. These bits indicate the type of debug event  
that caused the entry into debug state.  
Note  
On entry to debug state, the processor updates the WFAR register with the address of the  
instruction accessing the watchpointed address plus:  
+ 8 in ARM state  
+ 4 in Thumb state.  
11.8.10 Exceptions in debug state  
While in debug state, exceptions are handled as follows:  
Reset  
This exception is taken as in a normal processor state. This means the processor  
leaves debug state because of the system reset.  
Prefetch Abort  
This exception cannot occur because the processor does not fetch any instructions  
while in debug state.  
Debug  
The processor ignores debug events, including BKPT instructions.  
The processor ignores SVC exceptions.  
SVC  
Undefined  
When an Undefined exception occurs in debug state, the behavior of the  
processor is as follows:  
PC, CPSR, SPSR_und, and R14_und are unchanged  
the processor remains in debug state  
DSCR[8], sticky Undefined bit, is set.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-47  
         
Debug  
Precise Data abort  
When a precise Data Abort occurs in debug state, the behavior of the processor is  
as follows:  
PC, CPSR, SPSR_abt, and R14_abt are unchanged  
the processor remains in debug state  
DSCR[6], sticky precise data abort bit, is set  
DFSR and DFAR are set to the same values as if the abort had occurred in  
normal state.  
Imprecise Data Abort  
When an imprecise Data Abort occurs in debug state, the behavior of the  
processor is as follows, regardless of the setting of the CPSR A bit:  
PC, CPSR, SPSR_abt, and R14_abt are unchanged  
the processor remains in debug state  
DSCR[7], sticky imprecise data abort bit, is set  
the imprecise Data Abort does not cause the processor to perform an  
exception entry sequence so DFSR remains unchanged  
the processor does not act on this imprecise Data Abort on exit from the  
debug state, that is, the imprecise abort is discarded.  
Imprecise Data Aborts on entry and exit from debug state  
On entering debug state, the processor executes a Data Synchronization Barrier (DSB)  
sequence to ensure that any outstanding imprecise Data Aborts are detected, before starting  
debug operations.  
If the DSB operation detects an imprecise Data Abort, the processor records this event and its  
type as if the CPSR A bit was set. The purpose of latching this event is to ensure that it can be  
taken on exit from the debug state.  
Before forcing the processor to leave debug state, the debugger must execute a DSB sequence  
to ensure that all debugger-generated imprecise Data Aborts are detected, and therefore  
discarded, while still in debug state. After exiting debug state, the processor acts on any  
previously recorded imprecise Data Aborts if permitted by the CPSR A bit.  
11.8.11 Leaving debug state  
The debugger can force the processor to leave debug state:  
by setting the restart request bit, DRCR[1], to 1  
through the Cross Trigger Interface (CTI) external restart request mechanism.  
When one of those restart requests occurs, the processor:  
1.  
2.  
3.  
4.  
5.  
Clears the DSCR[1] core restarted flag.  
Leaves debug state.  
Clears the DSCR[0] core halted flag.  
Drives the DBGACK signal LOW, unless the DSCR[11] DbgAck bit is set to 1.  
Starts executing instructions from the address last written to the PC in the processor mode  
and state indicated by the current value of the CPSR. The CPSR IT execution state bit is  
restarted with the current value applying to the first instruction on restart.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-48  
 
Debug  
6.  
Sets the DSCR[1] core restarted flag to 1.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-49  
Debug  
11.9 Cache debug  
This section describes cache debug. It consists of:  
11.9.1 Cache pollution in debug state  
If bit [0] of the Debug State Cache Control Register (DSCCR) is set to 0 while the processor is  
in debug state, then the L1 data cache does not perform any line fill.  
Note  
No special feature is required to prevent L1 instruction cache pollution because instruction side  
fetches cannot occur while in debug state.  
11.9.2 Cache coherency in debug state  
The debugger can update memory while in debug state:  
to replace an instruction with a BKPT, or to restore the original instruction  
to download code for the processor to execute on leaving debug state.  
The debugger can maintain cache coherency in both these situations with the following features:  
If bit [2] of the DSCCR is set to 0 while the processor is in debug state, then the processor  
treats any memory access that hits in L1 data cache as write-through, regardless of the  
memory region attributes. This guarantees that the L1 instruction cache can see the  
changes to the code region without the debugger executing a time-consuming and  
device-specific sequence of cache clean operations.  
After the code is written to memory, the debugger can execute either a CP15 instruction  
cache invalidate all operation, or a CP15 instruction cache invalidate line operation.  
Note  
The processor can normally execute CP15 instruction cache invalidate all operation or CP15  
instruction cache invalidate line operation only in Privileged mode. However, in debug state the  
processor can execute these instructions even when invasive debug is not permitted in  
Privileged mode. This exception to the rule enables the debugger to maintain coherency.  
11.9.3 Cache usage profiling  
You can obtain cache usage profiling information using the Performance Monitoring Unit  
(PMU). The processor can count cache accesses and misses over a period of time. See Chapter 6  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-50  
         
Debug  
11.10 External debug interface  
The system can access memory-mapped debug registers through the processor APB slave port.  
This section describes the APB interface and the miscellaneous debug input and output signals:  
11.10.1 APB signals  
The APB slave port is compliant with the AMBA Advanced Peripheral Bus specification v3 and  
can be connected to the Debug Access Port (DAP). This APB slave interface supports 32-bits  
wide data, stalls, slave-generated aborts, and ten address bits [11:2] mapping 4KB of memory.  
An extra PADDRDBG31 signal indicates to the processor the source of access.  
Table A-12 on page A-17 shows the external debug interface signals.  
11.10.2 Miscellaneous debug signals  
This section describes the miscellaneous debug signals.  
EDBGRQ  
This signal generates a halting debug event, that is, it requests the processor to enter debug state.  
When this occurs, the DSCR[5:2] method-of-debug entry bits are set to b0100. When  
EDBGRQ is asserted, it must be held until DBGACK is asserted. Failure to do so leads to  
Unpredictable behavior of the processor.  
DBGACK  
The processor asserts DBGACK to indicate that the system has entered debug state. It serves as  
a handshake for the EDBGRQ signal. The DBGACK signal is also driven HIGH when the  
debugger sets the DSCR[10] DbgAck bit to 1.  
DBGNOPWRDWN  
The processor asserts DBGNOPWRDWN when bit [0] of the Device Power down and Reset  
Control Register is 1. The processor power controller must work in Emulate mode when this  
signal is HIGH.  
DBGROMADDR  
The DBGROMADDR signal specifies bits [31:12] of the debug ROM physical address. This  
is a configuration input and must be tied off or only change while the processor is in reset. In a  
system with multiple debug ROMs, this address must be tied off to point to the top-level ROM  
address.  
DBGROMADDRV is the valid signal for DBGROMADDR. If the address cannot be  
determined, DBGROMADDR must be tied off to zero and DBGROMADDRV must be tied  
LOW. The value of these signals can be read from the Debug ROM Address Register (DRAR).  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-51  
         
Debug  
DBGSELFADDR  
The DBGSELFADDR signal specifies bits [31:12] of the offset from the debug ROM physical  
address to the physical address where the processor APB port is mapped to the base of the 4KB  
debug register map. This is a configuration input and must be tied off or only change while the  
processor is in reset.  
DBGSELFADDRV is the valid signal for DBGSELFADDR. If the offset cannot be  
determined, DBGSELFADDR must be tied off to zero and DBGSELFADDRV must be tied  
LOW. The value of these signals can be read from the Debug Self Address Register (DSAR).  
DBGRESTART  
The DBGRESTART signal is used to bring the processor out of debug halt state. The processor  
acknowledges DBGRESTART by asserting DBGRESTARTED, and then starts fetching  
instructions when DBGRESTART is deasserted.  
DBGRESTARTED  
The processor asserts DBGRESTARTED in response to a DBGRESTART request, when it is  
ready to exit debug halt state and return to normal run state.  
DBGTRIGGER  
The processor asserts DBGTRIGGER to indicate that the system has accepted a debug request  
and attempts to enter debug state. It is not a handshake for the EDBGRQ signal. If DBGACK  
does not go HIGH following DBGTRIGGER, the memory system has stopped responding and  
the processor has not entered debug state.  
Table A-13 on page A-17 shows the debug miscellaneous signals.  
11.10.3 Authentication signals  
Table 11-42 shows a list of the valid authentication signals and the associated debug  
permissions. Authentication signals are used to configure the processor so its activity can only  
be debugged or traced in a certain subset of processor modes.  
Table 11-42 Authentication signal restrictions  
Non-invasive debug permitted  
in User and Privileged modes  
DBGENa  
NIDEN  
0
0
1
0
No  
X
1
Yes  
Yes  
a. When DBGEN is LOW, the processor behaves as if  
DSCR[15:14] equals b00 with the exception that halting  
debug events are ignored when this signal is LOW.  
Changing the authentication signals  
The NIDEN, and DBGEN input signals are either tied off to some fixed value or controlled by  
some external device.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-52  
     
Debug  
If software running on the processor has control over an external device that drives the  
authentication signals, it must make the change using a safe sequence:  
1.  
Execute an implementation-specific sequence of instructions to change the signal value.  
For example, this might be a single STRinstruction that writes certain value to a control  
register in a system peripheral.  
2.  
3.  
If step1 involves any memory operation, issue a Data Synchronization Barrier (DSB)  
instruction.  
Poll the DSCR or Authentication Status Register to check whether the processor has  
already detected the changed value of these signals. This is required because the system  
might not issue the signal change to the processor until several cycles after the DSB  
completes.  
4.  
Issue an Instruction Synchronization Barrier (ISB) instruction.  
The software cannot perform debug or analysis operations that depend on the new value of the  
authentication signals until this procedure is complete. The same rules apply when the debugger  
has control of the processor through the ITR while in debug state.  
The values of the DBGEN and NIDEN signals can be determined by polling DSCR[17:16],  
DSCR[15:14], or the Authentication Status Register.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-53  
 
Debug  
11.11 Using the debug functionality  
This section provides some examples of using the processor debug functionality, both from the  
point of view of a software engineer writing code to run on an ARM processor and of a  
developer creating debug tools for the processor. In the former case, examples are given in ARM  
assembly language. In the latter case, the examples are in C pseudo-language, intended to  
convey the algorithms to be used. These examples are not intended as source code for a  
debugger.  
The debugger examples use a pair of pseudo-functions such as the following:  
uint32 ReadDebugRegister(int reg_num)  
{
// read the value of the debug register reg_num at address reg_num << 2  
}
WriteDebugRegister(int reg_num, uint32 val)  
{
// write the value val to the debug register reg_num at address reg_num >> 2  
}
A basic function for using the debug state is executing an instruction through the ITR.  
Example 11-1 shows the sequence for executing an ARM instruction through the ITR.  
Example 11-1 Executing an ARM instruction through the ITR  
ExecuteARMInstruction(uint32 instr)  
{
// Step 1. Poll DSCR until InstrCompl is set.  
repeat  
{
dscr := ReadDebugRegister(34);  
}
until (dscr & (1<<24));  
// Step 2. Write the opcode to the ITR.  
WriteDebugRegister(33, instr);  
// Step 3. Poll DSCR until InstrCompl is set.  
repeat  
{
dscr := ReadDebugRegister(34);  
}
until (dscr & (1<<24);  
}
This section describes:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-54  
     
Debug  
11.11.1 Debug communications channel  
There are two ways that an external debugger can send data to or receive data from the  
processor:  
The debug communications channel, when the processor is not in debug state. It is defined  
as the set of resources used for communicating between the external debugger and  
software running on the processor.  
The mechanism for forcing the processor to execute ARM instructions, when the  
processor is in debug state. For more information, see Executing instructions in debug  
Rules for accessing the DCC  
At the processor side, the debug communications channel resources are:  
CP14 Debug Register c5 (DTR)  
CP14 Debug Register c1 (DSCR).  
The ARMv7 debug architecture is implemented on the processor so that:  
If a read of the CP14 DSCR returns 1 for the DTRTXfull flag:  
a following read of the CP14 DTR returns valid data and DTRTXfull is cleared. No  
prefetch flush is required between these two CP14 instructions.  
a following write to the CP14 DTR is Unpredictable.  
If a read of the CP14 DSCR returns 0 for the DTRTXfull flag:  
a following read of the CP14 DTR returns an Unpredictable value.  
a following write to the CP14 DTR writes the intended 32-bit word, and sets  
DTRRXfull to 1. No prefetch flush is required between these two CP14  
instructions.  
When Nonblocking mode is selected for DTR accesses, the following conditions are true for  
memory-mapped DSCR, memory-mapped DTRRX, and DTRTX registers:  
If a read of the memory-mapped DSCR returns 0 for the DTRTXfull flag:  
a following read of the memory-mapped DTRTX is ignored. For example, the  
content of DTRRXfull is unchanged and the read returns an Unpredictable value.  
a following write of the memory-mapped DTRRX passes valid data to the processor  
and sets DTRTXfull to 1.  
If a read of the memory-mapped DSCR returns 1 for the DTRTXfull flag:  
a following read of the memory-mapped DTRTX returns valid data and clears  
DTRRXfull.  
a following write of the memory-mapped DTRRX is ignored, that is, both  
DTRTXfull and DTRRX contents are unchanged.  
The ARMv7 debug architecture does not support other uses of the DCC resources. In particular,  
the processor does not support the following:  
CP14 DSCR[30:29] flags to access the memory-mapped DTRRX and DTRTX registers  
polling memory-mapped DSCR[30:29] flags to access CP14 DTR.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-55  
 
Debug  
Software access to the DCC  
Software running on the processor that sends data to the debugger through the target-to-host  
channel can use the sequence of instructions that Example 11-2 shows.  
Example 11-2 Target to host data transfer (target end)  
; r0 -> word to send to the debugger  
WriteDCC  
MRC  
BEQ  
MCR  
BX  
p14, 0, PC, c0, c1, 0  
WriteDCC  
p14, 0, Rd, c0, c5, 0  
lr  
Example 11-3 shows the sequence of instructions for sending data to the debugger through the  
host-to-target channel.  
Example 11-3 Host to target data transfer (target end)  
; r0 -> word sent by the debugger  
ReadDCC  
MRC  
BCC  
MRC  
BX  
p14, 0, PC, c0, c1, 0  
ReadDCC  
p14, 0, Rd, c0, c5, 0  
lr  
Debugger access to the DCC  
When not in debug state, a debugger can access the DCC through the external interface. The  
following examples show the pseudo-code operations for these accesses.  
Example 11-4 shows the code for target-to-host data transfer.  
Example 11-4 Target to host data transfer (host end)  
uint32  
{
ReadDCC()  
// Step 1. Poll DSCR until DTRTXfull is set to 1.  
repeat  
{
dscr := ReadDebugRegister(34);  
}
until (dscr & (1<<29));  
// Step 2. Read the value from DTRTX.  
dtr_val := ReadDebugRegister(35);  
return dtr_val;  
}
Example 11-5 shows the code for host-to-target data transfer.  
Example 11-5 Host to target data transfer (host end)  
WriteDCC(uint32 dtr_val)  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-56  
       
Debug  
{
// Step 1. Poll DSCR until DTRRXfull is clear.  
repeat  
{
dscr := ReadDebugRegister(34);  
}
until (!(dscr & (1<<30)));  
// Step 2. Write the value to DTRRX.  
WriteDebugRegister(32, dtr_val);  
}
While the processor is running, if the DCC is used as a data channel, it might be appropriate to  
poll the DCC regularly.  
Example 11-6 shows the code for polling the DCC.  
Example 11-6 Polling the DCC (host end)  
PollDCC  
{
dscr := ReadDebugRegister(34);  
if (dscr & (1<<29))  
{
// DTRTX (target -> host transfer register) full  
dtr := ReadDebugRegister(35)  
ProcessTargetToHostWord(dtr);  
}
if (!(dscr & (1<<30)))  
{
// DTRRX (host -> target transfer register) empty  
dtr := GetNextHostToTargetWord()  
WriteDebugRegister(32, dtr);  
}
}
11.11.2 Programming breakpoints and watchpoints  
This section describes the following operations:  
Programming simple breakpoints and the byte address select  
When programming a simple breakpoint, you must set the byte address select bits in the control  
register appropriately. For a breakpoint in ARM state, this is simple. For Thumb state, you must  
calculate the value based on the address.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-57  
     
Debug  
For a simple breakpoint, you can program the settings for the other control bits as Table 11-43  
shows:  
Table 11-43 Values to write to BCR for a simple breakpoint  
Bits  
Value to write  
Description  
[31:29]  
[28:24]  
[23]  
0b000  
0b00000  
0b0  
Reserved  
Breakpoint address mask  
Reserved  
[22:20]  
[19:16]  
[15:9]  
[8:5]  
0b000  
0b0000  
0b00  
Meaning of BVR  
Linked BRP number  
Reserved  
Derived from address Byte address select  
[4:3]  
0b00  
0b11  
0b1  
Reserved  
[2:1]  
Supervisor access control  
Breakpoint enable  
[0]  
Example 11-7 shows the sequence of instructions for setting a simple breakpoint.  
Example 11-7 Setting a simple breakpoint  
SetSimpleBreakpoint(int break_num, uint32 address, iset_t isa)  
{
// Step 1. Disable the breakpoint being set.  
WriteDebugRegister(80 + break_num, 0x0);  
// Step 2. Write address to the BVR, leaving the bottom 2 bits zero.  
WriteDebugRegister(64 + break_num, address & 0xFFFFFFC);  
// Step 3. Determine the byte address select value to use.  
case (isa) of  
{
// Note: The processor does not support Jazelle or ThumbEE states,  
// but the ARMv7 Debug architecture does  
when JAZELLE:  
byte_address_select := (1 << (address & 3));  
when THUMB:  
byte_address_select := (3 << (address & 2));  
when ARM:  
byte_address_select := 15;  
}
// Step 4. Write the mask and control register to enable the breakpoint.  
breakpoint  
WriteDebugRegister(80 + break_num, 7 | (byte_address_select << 5));  
}
Setting a simple aligned watchpoint  
The simplest and most common type of watchpoint watches for a write to a given address in  
memory. In practice, a data object spans a range of addresses but is aligned to a boundary  
corresponding to its size, so you must set the byte address select bits in the same way as for a  
breakpoint.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-58  
       
Debug  
For a simple watchpoint, you can program the settings for the other control bits as Table 11-44  
shows:  
Table 11-44 Values to write to WCR for a simple watchpoint  
Bits  
Value to write  
Description  
[31:29]  
[28:24]  
[23:21]  
[20]  
0b000  
0b00000  
0b000  
0b0  
Reserved  
Watchpoint address mask  
Reserved  
Enable linking  
Linked BRP number  
Reserved  
[19:16]  
[15:13]  
[12:5]  
[4:3]  
0b0000  
0b00  
Derived from address Byte address select  
0b10  
0b11  
0b1  
Load/Store access control  
[2:1]  
Privileged access control  
Watchpoint enable  
[0]  
Example 11-8 shows the code for setting a simple aligned watchpoint.  
Example 11-8 Setting a simple aligned watchpoint  
SetSimpleAlignedWatchpoint(int watch_num, uint32 address, int size)  
{
// Step 1. Disable the watchpoint being set.  
WriteDebugRegister(112 + watch_num, 0);  
// (Step 2. Write address to the WVR, leaving the bottom 3 bits zero.  
WriteDebugRegister(96 + watch_num, address & 0xFFFFFF8);  
// Step 3. Determine the byte address select value to use.  
case (size) of  
{
when 1:  
byte_address_select := (1 << (address & 7));  
when 2:  
byte_address_select := (3 << (address & 6));  
when 4:  
byte_address_select := (15 << (address & 4));  
when 8:  
byte_address_select := 255;  
}
// Step 4. Write the mask and control register to enable the watchpoint.  
breakpoint  
WriteDebugRegister(112 + watch_num, 23 | (byte_address_select << 5));  
}
Setting a simple unaligned watchpoint  
Using the byte address select bits, certain unaligned objects up to a doubleword (64 bits) can be  
watched in a single watchpoint. However, this cannot cover all cases, and in many cases a  
second watchpoint might be required.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-59  
       
Debug  
Table 11-45 shows some examples.  
Table 11-45 Example byte address masks for watchpointed objects  
Object size  
in bytes  
First address First byte  
Second address  
Second byte  
address mask  
Address of object  
value  
address mask value  
0x00008000  
0x00008007  
0x00009000  
0x0000900c  
0x0000900d  
0x0000A000  
0x0000A003  
0x0000A005  
0x0000B000  
0x0000B001  
1
1
2
2
2
4
4
4
8
8
0x00008000  
0x00008000  
0x00009000  
0x00009000  
0x00009000  
0x0000A000  
0x0000A000  
0x0000A000  
0x0000B000  
0x0000B000  
0b00000001  
0b10000000  
0b00000011  
0b11000000  
0b10000000  
0b00001111  
0b01111000  
0b11100000  
0b11111111  
0b11111110  
Not required  
Not required  
Not required  
Not required  
0x00009008  
-
-
-
-
0b00000001  
Not required  
Not required  
0x0000A008  
-
-
0b00000001  
-
Not required  
0x0000B008  
0b00000001  
Example 11-9 shows the code for setting a simple unaligned watchpoint.  
Example 11-9 Setting a simple unaligned watchpoint  
bool SetSimpleWatchpoint(int watch_num, uint32 address, int size)  
{
// Step 1. Disable the watchpoint being set.  
WriteDebugRegister(112 + watch_num, 0x0);  
// Step 2. Write addresses to the WVRs, leaving the bottom 3 bits zero.  
WriteDebugRegister(96 + watch_num, (address & 0xFFFFFF8));  
// Step 3. Determine the byte address select value to use.  
byte_address_select := (1 << size) - 1;  
byte_address_select := (byte_address_select) << (address & 7);  
// Step 4. Write the mask and control register to enable the breakpoint.  
WriteDebugRegister (112 + watch_num, 5'b23 | ((byte_address_select & 0xFF) << 5));  
// Step 5. Set second watchpoint if required. This is the case if the byte  
// address mask is more than 8 bits.  
if (byte_address_select >= 256)  
{
WriteDebugRegister(112 + watch_num + 1, 0);  
WriteDebugRegister(96 + watch_num + 1, (address & 0xFFFFFF8) + 8);  
WriteDebugRegister(112 + watch_num + 1 23| ((byte_address_select & 0xFF00) >> 3));  
}
// Step 6. Return flag to caller indicating if second watchpoint was used.  
return (byte_address_select >= 256)  
}
11.11.3 Single-stepping  
You can use the breakpoint mismatch bit to implement single-stepping on the processor. Unlike  
high-level stepping, single-stepping implements a low-level step that executes a single  
instruction at a time. With high-level stepping, the instruction is decoded to determine the  
address of the next instruction and a breakpoint is set at that address.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-60  
       
Debug  
Example 11-10 shows the code for single-stepping off an instruction.  
Example 11-10 Single-stepping off an instruction  
SingleStepOff(uint32 address)  
{
bkpt := FindUnusedBreakpointWithMismatchCapability();  
SetComplexBreakpoint(bkpt, address, 4 << 20);  
}
Note  
In Example 11-10, the third parameter of SetComplexBreakpoint()indicates the value to set  
BCR[22:20].  
This method of single-stepping steps off the instruction that might not necessarily be the same  
as stepping to the next instruction executed. In certain circumstances, the next instruction  
executed might be the same instruction being stepped off.  
The simplest example of this is a branch to a self instruction such as (B .). In this case, the  
wanted behavior is most likely to step off the branch to self because this is often used as a means  
of waiting for an interrupt.  
A more complex example is a return from function that returns to the same point. For example,  
a simple recursive function might terminate with:  
BL  
ThisFunction  
POP  
{saved_registers, pc}  
In this case, the POPinstruction loads a link register that is saved at the start of the function, and  
if that is the link register created by the BLinstruction shown, it points back at the POPinstruction.  
Therefore, this single step code unwinds the entire call stack to the point of the original caller,  
rather than stepping out a level at a time. It is not possible to single step this piece of code using  
either the high-level or low-level stepping methods.  
11.11.4 Debug state entry  
On entry to debug state, the debugger can read the processor state, including all registers and  
the PC, and determine the cause of the exception from the DSCR method-of-entry bits.  
Example 11-11 shows the code for entry to debug state.  
Example 11-11 Entering debug state  
OnEntryToDebugState(PROCESSOR_STATE *state)  
{
// Step 1. Read the DSCR to determine the cause of debug entry.  
state->dscr := ReadDebugRegister(34);  
// Step 2. Issue a DataSynchronizationBarrier instruction if required;  
// this is not required by Cortex-R4 but is required for ARMv7  
// debug.  
if ((state->dscr & (1<<19)) == 0)  
{
ExecuteARMInstruction(0xEE070F9A)  
// Step 3. Poll the DSCR for DSCR[19] to be set.  
repeat  
{
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-61  
     
Debug  
dscr := ReadDebugRegister(34);  
until (dscr & (1<<19));  
// Step 4. Read the entire processor state. The function ReadAllRegisters  
}
}
//  
//  
reads all general-purpose registers for all processor mode, and saves  
the data in “state”.  
ReadAllRegisters(state);  
// Step 5. Based on the CPSR (processor state), determine the actual restart  
//  
address  
if (state->cpsr & (1<<5);  
{
// set the T bit to Thumb state  
state->pc := state->pc - 4;  
}
elseif (state->cpsr & (1<<24))  
{
// Set the J bit to Jazelle state. Note: ARM Cortex-R4 does not support  
// Jazelle state but ARMv7 debug does.  
state->pc := state->pc - IMPLEMENTATION DEFINED  
value;  
}
else  
{
// ARM state  
state->pc := state->pc - 8;  
}
// Step 6. If the method of entry was Watchpoint Occurred, read the WFAR  
// register  
method_of_debug_entry := ((state->dscr >> 2) & 0xF;  
if (method_of_debug_entry == 2 || method_of_debug_entry == 10)  
{
state->wfar := ReadDebugRegister(6);  
}
}
11.11.5 Debug state exit  
When exiting debug state, the program counter must always be written. If the execution state or  
CPSR must be changed, this must be done before writing to the PC because writing to the CPSR  
can affect the PC.  
Having restored the program state, the debugger can restart by writing to bit [1] of the Debug  
Run Control Register. It must then poll bit [1] of the Debug Status and Control Register to  
determine if the core has restarted.  
Example 11-12 shows the code for exit from debug state.  
Example 11-12 Leaving debug state  
ExitDebugState(PROCESSOR_STATE *state)  
{
// Step 1. Update the CPSR value  
WriteCPSR(state->cpsr);  
// Step 2. Restore any registers corrupted by debug state. The function  
// WriteAllRegisters restores all general-purpose registers for all  
// processor modes apart from R0.  
WriteAllRegisters(state);  
// Step 3. Write the return address.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-62  
   
Debug  
WritePC(state->pc);  
// Step 4. Writing the PC corrupts R0 therefore, restore R0 now.  
WriteRegister(0, state->r0);  
// Step 5. Write the restart request bit in the DRCR.  
WriteDebugRegister(36, 1<<1);  
// Step 6. Poll the RESTARTED flag in the DSCR.  
repeat  
{
dscr := ReadDebugRegister(34);  
}
until (dscr & (1<<1));  
}
11.11.6 Accessing registers and memory in debug state  
This section describes the following:  
Reading and writing registers through the DCC  
To read a single register, the debugger can use the sequence that Example 11-13 shows. This  
sequence depends on two other sequences, Executing an ARM instruction through the ITR on  
Example 11-13 Reading an ARM register  
uint32 ReadARMRegister(int Rd)  
{
// Step 1. Execute instruction MCR p14, 0, Rd, c0, c5, 0 through the ITR.  
ExecuteARMInstruction(0xEE000E15 + (Rd<<12));  
// Step 2. Read the register value through DTRTX.  
reg_val := ReadDCC();  
return reg_val;  
}
Example 11-14 shows a similar sequence for writing an ARM register.  
Example 11-14 Writing an ARM register  
WriteRegister(int Rd, uint32 reg_val)  
{
// Step 1. Write the register value to DTRRX.  
WriteDCC(reg_val);  
// Step 2. Execute instruction MRC p14, 0, Rd, c0, c5, 0 to the ITR.  
ExecuteARMInstruction(0xEE100E15 + (Rd<<12));  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-63  
       
Debug  
}
Reading the PC in debug state  
Example 11-15 shows the code to read the PC.  
Example 11-15 Reading the PC  
ReadPC()  
{
// Step 1. Save R0  
saved_r0 := ReadRegister(0);  
// Step 2. Execute the instruction MOV r0, pc through the ITR.  
ExecuteARMInstruction(0xE1A0000F);  
// Step 3. Read the value of R0 that now contains the PC.  
pc := ReadRegister(0);  
// Step 4. Restore the value of R0.  
WriteRegister(0, saved_r0);  
return pc;  
}
Note  
You can use a similar sequence to write to the PC to set the return address when leaving debug  
state.  
Reading the CPSR in debug state  
Example 11-16 shows the code for reading the CPSR.  
Example 11-16 Reading the CPSR  
ReadCPSR()  
{
// Step 1. Save R0.  
saved_r0 := ReadRegister(0);  
// Step 2. Execute instruction MRS R0, CPSR through the ITR.  
ExecuteARMInstruction(0xE10F0000);  
// Step 3. Read the value of R0 that now contains the CPSR  
cpsr_val := ReadRegister(0);  
// Step 4. Restore the value of R0.  
WriteRegister(0, saved_r0);  
return cpsr_val;  
}
Note  
You can use similar sequences to read the SPSR in Privileged modes.  
Writing the CPSR in debug state  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-64  
         
Debug  
Example 11-17 Writing the CPSR  
WriteCPSR(uint32 cpsr_val)  
{
// Step 1. Save R0.  
saved_r0 := ReadRegister(0);  
// Step 2. Write the new CPSR value to R0.  
WriteRegister(0, cpsr_val);  
// Step 3. Execute instruction MSR R0, CPSR through the ITR.  
ExecuteARMInstruction(0xE12FF000);  
// Step 4. Execute a PrefetchFlush instruction through the ITR.  
ExecuteARMInstruction(9xEE070F95);  
// Step 5. Restore the value of R0.  
WriteRegister(0, saved_r0);  
}
Reading memory  
Example 11-18 shows the code for reading a byte of memory.  
Example 11-18 Reading a byte of memory  
uint8 ReadByte(uint32 address, bool &aborted)  
{
// Step 1. Save the values of R0 and R1.  
saved_r0 := ReadRegister(0);  
saved_r1 := ReadRegister(1);  
// Step 2. Write the address to R0.  
WriteRegister(0, address);  
// Step 3. Execute the instruction LDRB R1,[R0] through the ITR.  
ExecuteARMInstruction(0xE5D01000);  
// Step 4. Read the value of R1 that contains the data at the address.  
datum := ReadRegister(1);  
// Step 5. Restore the corrupted registers R0 and R1.  
WriteRegister(0, saved_r0);  
WriteRegister(1, saved_r1);  
// Step 6. Check the DSCR for a sticky abort.  
aborted := CheckForAborts();  
return datum;  
}
Example 11-19 shows the code for checking for aborts after a memory access.  
Example 11-19 Checking for an abort after memory access  
bool CheckForAborts()  
{
// Step 1. Check the DSCR for a sticky abort.  
dscr := ReadDebugRegister(34);  
if (dscr & ((1<<6) + (1<<7))  
{
// Step 2. Clear the sticky flag by writing DRCR[2].  
WriteDebugRegister(36, 1<<2);  
return true;  
}
else  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-65  
       
Debug  
{
}
return false;  
}
Note  
You can use a similar sequence to read a halfword of memory and to write to memory.  
To read or write blocks of memory, substitute the data instruction with one that uses  
post-indexed addressing. For example:  
LDRB R1, [R0],1  
This prevents reloading the address value for each sequential word.  
Example 11-20 shows the code for reading a block of bytes of memory.  
Example 11-20 Reading a block of bytes of memory  
ReadBytes(uint32 address, bool &aborted, uint8 *data, int nbytes)  
{
// Step 1. Save the value of R0 and R1.  
saved_r0 := ReadRegister(0);  
saved_r1 := ReadRegister(1);  
// Step 2. Write the address to R0  
WriteRegister(0, address);  
while (nbytes > 0)  
{
// Step 3. Execute instruction LDRB R1,[R0],1 through the ITR.  
ExecuteARMInstruction(0xE4D01001);  
// Step 4. Read the value of R1 that contains the data at the  
// address.  
*data++ := ReadRegister(1);  
--nbytes;  
}
// Step 5. Restore the corrupted registers R0 and R1.  
WriteRegister(0, saved_r0);  
WriteRegister(1, saved-r1);  
// Step 6. Check the DSCR for a sticky abort.  
aborted := CheckForAborts();  
return datum;  
}
Example 11-21 shows the sequence for reading a word of memory.  
Note  
A faster method is available for reading and writing words using the direct memory access  
Example 11-21 Reading a word of memory  
uint32 ReadWord(uint32 address, bool &aborted)  
{
// Step 1. Save the value of R0.  
saved_r0 := ReadRegister(0);  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-66  
   
Debug  
// Step 2. Write the address to R0.  
WriteRegister(0, address);  
// Step 3. Execute instruction LDC p14, c5, [R0] through the ITR.  
ExecuteARMInstruction(0xED905E00);  
// Step 4. Read the value from the DTR directly.  
datum := ReadDCC();  
// Step 5. Restore the corrupted register R0.  
WriteRegister(0, saved_r0);  
// Step 6. Check the DSCR for a sticky abort.  
aborted := CheckForAborts();  
return datum;  
}
Fast register read/write  
When multiple registers must be read in succession, you can optimize the process by placing the  
DCC into stall mode and by writing the value 1 to the DCC access mode bits. For more  
Example 11-22 shows the sequence to change the DTR access mode.  
Example 11-22 Changing the DTR access mode  
SetDTRAccessMode(int mode)  
{
// Step 1. Write the mode value to DSCR[21:20].  
dscr := ReadDebugRegister(34);  
dscr := (dscr & ~(0x3<<20)) | (mode<<20);  
WriteDebugRegister(34, dscr);  
}
Example 11-23 shows the sequence to read registers in stall mode.  
Example 11-23 Reading registers in stall mode  
ReadRegisterStallMode(int Rd)  
{
// Step 1. Write the opcode for MCR p14, 0, Rd, c5, c0 to the ITR.  
// Write stalls until the ITR is ready.  
WriteDebugRegister(33, 0xEE000E15 + (Rd<<12));  
// Step 2. Read the register value through the DCC. Read stalls until  
// DTRTX is ready  
reg_val := ReadDebugRegister(32);  
return reg_val;  
}
Example 11-24 shows the sequence to write registers in stall mode.  
Example 11-24 Writing registers in stall mode  
WriteRegisterInStallMode(int Rd, uint32 value)  
{
// Step 1. Write the value to the DTRRX.  
// Write stalls until the DTRRX is ready.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-67  
       
Debug  
WriteDebugRegister(32, value);  
// Step 2. Write the opcode for MRC p14, 0, Rd, c5, c0 to the ITR.  
// Write stalls until the ITR is ready.  
WriteDebugRegister(33, 0xEE100E15 + (Rd<<12));  
}
Note  
To transfer a register to the processor when in stall mode, you are not required to poll the DSCR  
each time an instruction is written to the ITR and a value read from or written to the DTR. The  
processor stalls using the signal PREADYDBG until the previous instruction has completed or  
the DTR register is ready for the operation.  
Fast memory read/write  
This section provides example code to enable faster reads from memory by making use of the  
DTR access mode.  
Example 11-25 shows the sequence for reading a block of words of memory.  
Example 11-25 Reading a block of words of memory  
ReadWords(uint32 address, bool &aborted, uint32 *data, int nwords)  
{
// Step 1. Write the value 0b01 to DSCR[21:20] for stall mode.  
SetDTRAccessMode(1);  
// Step 2. Save the value of R0.  
saved_r0 := ReadRegisterInStallMode(0);  
// Step 3. Write the address to read from to the DTRRX.  
// Write stalls until the DTRRX is ready.  
WriteRegisterInStallMode(0, address);  
// Step 4. Write the opcode for LDC p14, c5, [R0], 4 to the ITR.  
// Write stalls until the ITR is ready.  
WriteDebugRegister(33, 0xECB05E01);  
// Step 5. Write the value 0b10 to DSCR[21:20] for fast mode.  
SetDCCAccessMode(2);  
// Step 6. Loop reading out the data.  
// Each time a word is read from the DTRTX, the instruction is reissued.  
while (nwords > 1)  
{
*data++ = ReadDebugRegister(35);  
--nwords;  
}
// Step 7. Write the value 0b00 to DSCR[21:20] for non-blocking mode.  
SetDTRAccessMode(0);  
// Step 8. Need to wait for the final instruction to complete. If there  
// was an abort, this will complete immediately.  
do  
{
dscr := ReadDebugRegister(34);  
}
until (dscr & (1<<24));  
// Step 9: Check for aborts.  
aborted := CheckForAborts();  
// Step 10: Read the final word from the DCC.  
if (!aborted) *data := ReadDCC();  
// Step 11. Restore the corrupted register r0.  
WriteRegister(0, saved_r0);  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-68  
   
Debug  
}
Example 11-26 shows the sequence for writing a block of words to memory.  
Example 11-26 Writing a block of words to memory (fast download)  
WriteWords(uint32 address, bool &aborted, uint32 *data, int nwords)  
{
// Step 1. Save the value of R0.  
saved_r0 := ReadRegister(0);  
// Step 2. Write the value 0b10 to DSCR[21:20] for fast mode.  
SetDTRAccessMode(2);  
// Step 3. Write the opcode for MRC p14, 0, R0, c5, c0 to the ITR.  
// Write stalls until the ITR is ready but the instruction is not issued.  
WriteDebugRegister(33, 0xEE100E15);  
// Step 4. Write the address to read from to the DTRRX  
// Write stalls until the ITR is ready, but the instruction is not reissued.  
WriteDebugRegister(32, address);  
// Step 5. Write the opcode for STC p14, c5, [R0], 4 to the ITR.  
// Write stalls until the ITR is ready but the instruction is not issued.  
WriteDebugRegister(33, 0xECA05E01);  
// Step 6. Loop writing the data.  
// Each time a word is written to the DTRRX, the instruction is reissued.  
while (nwords > 0)  
{
WriteDebugRegister(35, *data++);  
--nwords;  
}
// Step 7. Write the value b00 to DSCR[21:20] for normal mode.  
SetDTRAccessMode(0);  
// Step 8. Restore the corrupted register R0.  
WriteRegister(0, saved_r0);  
// Step 9. Check the DSCR for a sticky abort.  
aborted := CheckForAborts();  
}
Note  
As the amount of data transferred increases, these functions reach an optimum performance of  
one debug register access per data word transferred.  
After writing data to memory, you must execute a data synchronization barrier instruction to  
ensure that the memory window updates properly  
Accessing coprocessor registers  
The sequence for accessing coprocessor registers is the same for the PC and CPSR. That is, you  
must first execute an instruction to transfer the register to an ARM register, then read the value  
back through the DTR.  
Example 11-27 shows the sequence for reading a coprocessor register.  
Example 11-27 Reading a coprocessor register  
uint32 ReadCPReg(int CPnum, int opc1, int CRn, int CRm, int opc2)  
{
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-69  
     
Debug  
// Step 1. Save R0.  
saved_r0 := ReadRegister(0);  
// Step 2. Execute instruction MCR p15, 0, R0, c0, c1, 0 through the ITR.  
ExecuteARMInstruction(0xEE000010 + (CPnum<<8) + (opc1<<21) + (CRn<<16) + CRm  
// Step 3. Read the value of R0 that now contains the CP register.  
CP15c1 := ReadRegister(0);  
+ (opc2<<5));  
// Step 4. Restore the value of R0.  
WriteRegister(0, saved_r0);  
return CP15c1;  
}
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-70  
Debug  
11.12 Debugging systems with energy management capabilities  
The processor offers functionality for debugging systems with energy-management capabilities.  
This section describes scenarios where the OS takes energy-saving measures when in an idle  
state.  
The different measures that the OS can take to save energy during an idle state are divided into  
two groups:  
Standby  
The OS takes measures that reduce energy consumption but maintain the  
processor state.  
Power down The OS takes measures that reduce energy consumption but do not maintain the  
processor state. Recovery involves a reset of the processor after the power level  
has been restored, and reinstallation of the processor state.  
Standby is the least invasive OS energy-saving state because it only implies that the core is  
unavailable. It does not clear any of the debug settings. For this case, the processor offers the  
following:  
If the processor is in standby and a halting debug event occurs, the processor:  
leaves standby  
retires the Wait-For-Interrupt (WFI) instruction  
enters debug state.  
If the processor is in standby and detects an APB port access, it temporarily leaves standby  
state to complete the transaction. While the processor wakes up from standby, the APB  
access is held by keeping the PREADYDBG signal LOW.  
11.12.1 Emulating power down  
By writing to bit [0] of the PRCR, the debugger asserts the DBGNOPWRDWN output. The  
expected usage model of this signal is that it connects to the system power controller and that,  
when HIGH, it indicates that this controller must work in emulate mode.  
On a power-down request from the processor, if the power controller is in emulate mode, it does  
not remove processor power or ETM power. Otherwise, it behaves exactly the same as in normal  
mode.  
Emulating power down is ideal for debugging applications running on top of operating systems  
that are free of errors because the debug register settings are not lost on a power-down event.  
However, you must ensure that:  
nIRQ and nFIQ interrupts to the processor are externally masked as part of the emulation  
to prevent them from retiring the WFIinstruction from the pipeline.  
The reset controller asserts nRESET on power up, rather than nSYSPORESET.  
Asserting nSYSPORESET on power up clears the debug registers inside the processor.  
The timing effects of power down and voltage stabilization are not factored in the  
power-down emulation. This is the case for systems with voltage recovery controlled by  
a closed loop system that monitors the processor supply voltage, rather than a fixed timed  
for voltage recovery.  
The emulation does not model state lost during power down, making it possible to miss  
errors in the state storage and recovery routines.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-71  
     
Debug  
Attaching the debugger for a postmortem debug session is not possible because setting the  
DBGNOPWRDWN signal to 1 might not cause the processor to power up. The effect of  
setting DBGNOPWRDWN to 1 when the processor is already powered down is  
implementation-defined, and is up to the system designer.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
11-72  
Chapter 12  
FPU Programmer’s Model  
This chapter describes the programmer’s model of the Floating Point Unit (FPU). The Cortex-R4F  
processor is a Cortex-R4 processor that includes the optional FPU. In this chapter, the generic term  
processor means only the Cortex-R4F processor.  
This chapter contains the following sections:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
12-1  
   
FPU Programmer’s Model  
12.1 About the FPU programmer’s model  
The FPU implements the VFPv3-D16 architecture and the Common VFP Sub-Architecture v2.  
This includes the instruction set of the VFPv3 architecture. See the ARM Architecture Reference  
Manual for information on the VFPv3 instruction set.  
12.1.1 FPU functionality  
The FPU is an implementation of the ARM Vector Floating Point v3 architecture, with 16  
double-precision registers (VFPv3-D16). It provides floating-point computation functionality  
that is compliant with the ANSI/IEEE Std 754-1985, IEEE Standard for Binary Floating-Point  
Arithmetic, referred to as the IEEE 754 standard. The FPU supports all data-processing  
instructions and data types in the VFPv3 architecture as described in the ARM Architecture  
Reference Manual.  
The FPU fully supports single-precision and double-precision add, subtract, multiply, divide,  
multiply and accumulate, and square root operations. It also provides conversions between  
fixed-point and floating-point data formats, and floating-point constant instructions. The FPU  
does not support any data processing operations on vectors in hardware. Any data processing  
instruction that operates on a vector generates an UNDEFINED exception. The operation can  
then be emulated in software if necessary.  
12.1.2 About the VFPv3-D16 architecture  
The VFPv3-D16 architecture only includes 16 double-precision registers. VFPv3 includes 32  
double-precision registers by default. An instruction which attempts to access any of the  
registers D16-D31 generates an UNDEFINED exception.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
12-2  
   
FPU Programmer’s Model  
12.2 General-purpose registers  
The FPU implements a VFP register bank. This bank is distinct from the ARM register bank.  
You can reference the VFP register bank using two explicitly aliased views. Figure 12-1 shows  
the two views of the register bank and the way the word and doubleword registers overlap.  
12.2.1 FPU views of the register bank  
In the FPU, you can view the register bank as:  
Sixteen 64-bit doubleword registers, D0-D15  
Thirty-two 32-bit single-word registers, S0-S31  
A combination of registers from the above views.  
.
.
S0  
S1  
S2  
S3  
S4  
S5  
S6  
S7  
D0  
D1  
D2  
D3  
...  
...  
S28  
S29  
S30  
S31  
D14  
D15  
Figure 12-1 FPU register bank  
The mapping between the registers is as follows:  
S<2n>maps to the least significant half of D<n>  
S<2n+1>maps to the most significant half of D<n>  
.
For example, you can access the least significant half of the value in D6by accessing S12, and  
the most significant half of the elements by accessing S13  
.
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
12-3  
       
FPU Programmer’s Model  
12.3 System registers  
The VFPv3 architecture describes the following system registers:  
Table 12-1 shows the VFP system registers in the Cortex-R4F FPU.  
Table 12-1 VFP system registers  
Register  
FMXR/FMRX <reg> field Access type Reset state  
a
Floating-Point System ID Register, FPSID  
b0000  
Read-only  
Read/write  
Read/write  
Read-only  
Read-only  
0x4102314x  
0x00000000  
0x00000000  
0x10110221  
0x00000001  
Floating-Point Status and Control Register, FPSCR b0001  
Floating-Point Exception Register, FPEXC  
VFP Feature Register 0, MVFR0  
b1000  
b0111  
b0110  
VFP Feature Register 1, MVFR1  
a. Bits [3:0] of the FPSID depend on the product revision. See the FPSID register description for more information.  
Note  
The FPSID, MVFR0, and MVFR1 Registers are read-only. Attempts to write these registers are  
ignored.  
Table 12-2 shows that some of the VFP system registers can only be accessed in Privileged  
modes.  
Table 12-2 Accessing VFP system registers  
Privileged access  
User access  
Register  
FPEXC EN=0 FPEXC EN=1 FPEXC EN=0 FPEXC EN=1  
FPSID  
Permitted  
Permitted  
Permitted  
Permitted  
Permitted  
Not permitted  
Not permitted  
Not permitted  
Not permitted  
Not permitted  
Permitted  
FPSCR  
Not permitted  
MVFR0, MVFR1 Permitted  
FPEXC Permitted  
Not permitted  
Not permitted  
Table 12-2 shows that a Privileged mode is sometimes required to access a VFP system register.  
When a Privileged mode is required, an instruction that attempts to access a register in a  
nonprivileged mode takes the Undefined Instruction exception.  
For a VFP system register to be accessible, it must follow the rules in Table 12-2 and the VFP  
must also be accessible according to the Coprocessor Access Register. See c1, Coprocessor  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
12-4  
           
FPU Programmer’s Model  
Note  
All hardware ID information is privileged access only:  
FPSID is privileged access only  
This is a change in VFPv3 compared to VFPv2.  
MVFR registers are privileged access only  
User code must issue a system call to determine the features that are supported.  
The following sections describe the VFP system registers:  
12.3.1 Floating-Point System ID Register, FPSID  
The FPSID Register is a read-only register that must be accessed in Privileged mode only. It  
indicates which VFP implementation is being used.  
Figure 12-2 shows the bit arrangement of the FPSID Register.  
31  
24 23 22  
16 15  
8
7
4
3
0
Implementer  
Sub architecture  
Part number  
Variant  
Revision  
HW  
Figure 12-2 Floating-Point System ID Register format  
Table 12-3 shows how the bit values correspond with the FPSID Register functions.  
Table 12-3 FPSID Register bit functions  
Bits  
Field  
Function  
[31:24] Implementer  
ARM Limited:  
0x41= A  
[23]  
Hardware or software  
0 = hardware implementation  
VFP architecture v3 or later with Common VFP subarchitecture v2a:  
[22:16] Subarchitecture version  
0x02  
[15:8]  
[7:4]  
[3:0]  
Part number  
Variant  
0x31= Cortex-R4F  
0x4= Cortex-R4F  
Revision  
a. For details of the Common VFP subarchitecture see the ARM Architecture Reference Manual.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
12-5  
           
FPU Programmer’s Model  
12.3.2 Floating-Point Status and Control Register, FPSCR  
FPSCR is a read/write register that can be accessed in both Privileged and nonprivileged modes.  
All bits described as DNM in Figure 12-3 are reserved for future expansion. These bits must be  
initialized to zeros. To ensure that these bits are not modified, any code other than initialization  
code must use read-modify-write techniques when writing to FPSCR. Failure to observe this  
rule can cause Unpredictable results in future systems.  
Figure 12-3 shows the bit arrangement of the FPSCR Register.  
31 30 29 28 27 26 25 24 23 22 21 20 19 18  
16 15 14 13 12 11 10 9  
8
7
6
5
4
3
2
1
0
N Z C V  
DNM  
LEN DNM  
QC  
DNM  
IDE  
IXE  
IXC  
UFC  
OFC  
DZC  
IOC  
DN  
UFE  
OFE  
DZE  
IOE  
IDC  
FZ  
RMODE  
STRIDE  
DNM  
Figure 12-3 Floating-Point Status and Control Register format  
Table 12-4 shows how the bit values correspond with the FPSCR Register functions.  
Table 12-4 FPSCR Register bit functions  
Bits  
Field  
Function  
[31]  
[30]  
[29]  
[28]  
[27]  
[26]  
[25]  
N
Set if comparison produces a less than result, resets to zero  
Set if comparison produces an equal result, resets to zero  
Set if comparison produces an equal, greater than, or unordered result, resets to zero  
Set if comparison produces an unordered result, resets to zero  
Do Not Modify (DNM)/Read As Zero (RAZ)  
Z
C
V
QC  
DNM  
DN  
DNM  
Default NaN mode enable bit:  
0 = default NaN mode disabled, this is the reset value  
1 = default NaN mode enabled.  
[24]  
FZ  
Flush-to-zero mode enable bit:  
0 = flush-to-zero mode disabled, this is the reset value  
1 = flush-to-zero mode enabled.  
[23:22] RMODE Rounding mode control field:  
b00 = round to nearest (RN) mode, this is the reset value  
b01 = round towards plus infinity (RP) mode  
b10 = round towards minus infinity (RM) mode  
b11 = round towards zero (RZ) mode.  
[21:20] STRIDE  
Indicates the vector stride, reset value is 0x0  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
12-6  
         
FPU Programmer’s Model  
Table 12-4 FPSCR Register bit functions (continued)  
Bits  
Field  
Function  
[19]  
DNM  
DNM  
[18:16] LEN  
[15] IDE  
[14:13] DNM  
Indicates the vector length, reset value is 0x0  
RAZ  
DNM  
[12]  
[11]  
[10]  
[9]  
IXE  
RAZ  
UFE  
OFE  
DZE  
IOE  
RAZ  
RAZ  
RAZ  
[8]  
RAZ  
[7]  
IDC  
DNM  
IXC  
UFC  
OFC  
DZC  
IOC  
Input Subnormal cumulative flag, resets to zero  
DNM  
[6:5]  
[4]  
Inexact cumulative flag, resets to zero  
Underflow cumulative flag, resets to zero  
Overflow cumulative flag, resets to zero  
Division by Zero cumulative flag, resets to zero  
Invalid Operation cumulative flag, resets to zero  
[3]  
[2]  
[1]  
[0]  
12.3.3 Floating-Point Exception Register, FPEXC  
The FPEXC Register is a read/write register accessible in Privileged modes only.  
The EN bit, FPEXC[30], is the VFP enable bit. Clearing EN disables VFP functionality, causing  
all VFP instructions apart from privileged system register accesses to generate an UNDEFINED  
exception. The EN bit is cleared on reset.  
Figure 12-4 shows the bit arrangement of the FPEXC Register.  
31 30 29 28  
0
Reserved  
DEX  
EN  
Reserved  
Figure 12-4 Floating-Point Exception Register format  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
12-7  
       
FPU Programmer’s Model  
Table 12-5 shows how the bit values correspond with the FPEXC Register functions.  
Table 12-5 Floating-Point Exception Register bit functions  
Bits  
Field  
Function  
[31]  
[30]  
[29]  
Reserved RAZ.  
EN  
VFP enable bit. Setting EN enables VFP functionality. Reset clears EN.  
DEX  
Set when an Undefined exception is taken because of a vector instruction that would have been  
executed if the processor supported vectors. This field is cleared when an Undefined exception is  
taken for any other reason. Resets to zero.  
[28:0] Reserved RAZ.  
12.3.4 Media and VFP Feature Registers, MVFR0 and MVFR1  
The VFP Feature Registers, MVFR0 and MVFR1, are read-only registers which describe the  
features supported by the FPU. These registers are accessible in Privileged modes only.  
Figure 12-5 shows the bit arrangement of the MVFR0 Register.  
31  
28 27  
24 23  
20 19  
16 15  
12 11  
8
7
4
3
0
RB  
RM  
SV  
SR  
D
TE  
DP  
SP  
Figure 12-5 MVFR0 Register format  
Table 12-6 shows how the bit values correspond with the MVFR0 Register functions.  
Table 12-6 MVFR0 Register bit functions  
Bits  
Field Function  
[31:28] RM  
[27:24] SV  
[23:20] SR  
All VFP rounding modes supported:  
0x1  
VFP short vector unsupported:  
0x0  
VFP hardware square root supported:  
0x1  
[19:16]  
D
VFP hardware divide supported:  
0x1  
[15:12] TE  
Only untrapped exception handling can be selected:  
0x0  
[11:8]  
[7:4]  
[3:0]  
DP  
SP  
Double precision supported in VFPv3:  
0x2  
Single precision supported in VFPv3:  
0x2  
RB  
16x64-bit media register bank supported:  
0x1  
Figure 12-6 on page 12-9 shows the bit arrangement of the MVFR1 Register.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
12-8  
             
FPU Programmer’s Model  
31  
20 19  
16 15  
12 11  
8
7
4
3
0
Reserved  
SP  
I
LS  
DN  
FZ  
Figure 12-6 MVFR1 Register format  
Table 12-7 shows how the bit values correspond with the MVFR1 Register.  
Table 12-7 MVFR1 Register bit functions  
Bits  
Field Function  
- Reserved  
[31:20]  
[19:16] SP  
Single-precision floating-point operations supported for VFP:  
0b0000= not supported  
[15:12]  
[11:8]  
[7:4]  
I
Integer operations supported for VFP:  
0b0000= not supported  
LS  
DN  
FZ  
Load and store instructions supported for VFP:  
0b0000= not supported  
Propagation of NaN values supported for VFP:  
0x1  
[3:0]  
Full denormal arithmetic supported for VFP:  
0x1  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
12-9  
       
FPU Programmer’s Model  
12.4 Modes of operation  
The FPU provides three modes of operation to accommodate a variety of applications:  
12.4.1 Full-compliance mode  
In full-compliance mode, the FPU processes all operations according to the IEEE 754 standard  
in hardware.  
12.4.2 Flush-to-zero mode  
Setting the FZ bit, FPSCR[24], enables flush-to-zero mode. In this mode, the FPU treats all  
subnormal input operands of arithmetic CDPoperations as zeros in the operation. Exceptions that  
result from a zero operand are signaled appropriately. VABS VNEG, and VMOVare not considered  
,
arithmetic CDPoperations and are not affected by flush-to-zero mode. A result that is tiny, as  
described in the IEEE 754 standard, for the destination precision is smaller in magnitude than  
the minimum normal value before rounding and is replaced with a zero. The IDC flag,  
FPSCR[7], indicates when an input flush occurs. The UFC flag, FPSCR[3], indicates when a  
result flush occurs.  
12.4.3 Default NaN mode  
Setting the DN bit, FPSCR[25], enables default NaN mode. In this mode, the result of any  
operation that involves an input NaN, or that generated a NaN result, returns the default NaN.  
Propagation of the fraction bits is maintained only by VABS VNEG, and VMOVoperations. All other  
,
CDPoperations ignore any information in the fraction bits of an input NaN.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
12-10  
         
FPU Programmer’s Model  
12.5 Compliance with the IEEE 754 standard  
When Default NaN (DN) and Flush-to-Zero (FZ) modes are disabled, the VFP functionality is  
compliant with the IEEE 754 standard in hardware. No support code is required to achieve this  
compliance.  
See the ARM Architecture Reference Manual for information about VFP architecture  
compliance with the IEEE 754 standard.  
12.5.1 Complete implementation of the IEEE 754 standard  
The following operations from the IEEE 754 standard are not supplied by the VFP instruction  
set:  
remainder  
round floating-point number to integer-valued floating-point number  
binary-to-decimal conversions  
decimal-to-binary conversions  
direct comparison of single-precision and double-precision values.  
For complete implementation of the IEEE 754 standard, VFP functionality must be augmented  
with library functions that implement these operations. See Application Note 98, VFP Support  
Code for information on the available library functions.  
12.5.2 IEEE 754 standard implementation choices  
Some of the implementation choices permitted by the IEEE 754 standard and used in the VFPv3  
architecture are described in the ARM Architecture Reference Manual.  
NaN handling  
All single-precision and double-precision values with the maximum exponent field value and a  
nonzero fraction field are valid NaNs. A most significant fraction bit of zero indicates a  
Signaling NaN (SNaN). A one indicates a Quiet NaN (QNaN). Two NaN values are treated as  
different NaNs if they differ in any bit. Table 12-8 shows the default NaN values in both  
single-precision and double-precision.  
Table 12-8 Default NaN values  
Single-precision  
Double-precision  
Sign  
0
0
Exponent  
Fraction  
0xFF  
0x7FF  
bit [22] = 1, bits [21:0] are all zeros bit [51] = 1, bits [50:0] are all zeros  
Processing of input NaNs for ARM floating-point functionality and libraries is defined as  
follows:  
In full-compliance mode, NaNs are handled as described in the ARM Architecture  
Reference Manual. The hardware processes the NaNs directly for arithmetic CDP  
instructions. For data transfer operations, NaNs are transferred without raising the Invalid  
Operation exception. For the non-arithmetic CDPinstructions, VABS VNEG, and VMOV, NaNs  
,
are copied, with a change of sign if specified in the instructions, without causing the  
Invalid Operation exception.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
12-11  
       
FPU Programmer’s Model  
In default NaN mode, arithmetic CDPinstructions involving NaN operands return the  
default NaN regardless of the fractions of any NaN operands. SNaNs in an arithmetic CDP  
operation set the IOC flag, FPSCR[0]. NaN handling by data transfer and non-arithmetic  
CDP instructions is the same as in full-compliance mode.  
Table 12-9 summarizes the effects of NaN operands on instruction execution.  
Table 12-9 QNaN and SNaN handling  
Instruction  
type  
Default  
NaN mode  
With QNaN operand  
With SNaN operand  
IOCa set. The SNaN is quieted and the  
result NaN is determined by the rules  
given in the ARM Architecture  
Reference Manual.  
Off  
The QNaN or one of the QNaN operands, if  
there is more than one, is returned  
according to the rules given in the ARM  
Architecture Reference Manual.  
Arithmetic CDP  
IOCa set. Default NaN returns.  
On  
Off  
On  
-
Default NaN returns.  
Non-arithmetic  
CDP  
NaN passes to destination with sign changed as appropriate.  
FCMP(Z)  
Unordered compare.  
IOC set. Unordered compare.  
IOC set. Unordered compare.  
FCMPE(Z)  
-
IOC set. Unordered compare.  
Off  
On  
Load/store  
All NaNs transferred.  
a. IOC is the Invalid Operation exception flag, FPSCR[0].  
Comparisons  
Comparison results modify the flags in the FPSCR Register. You can use the VMOV r15, FPSCR  
instruction (formerly FMSTAT) to transfer the current flags from the FPSCR Register to the CPSR  
Register. See the ARM Architecture Reference Manual for mapping of IEEE 754 standard  
predicates to ARM conditions. The flags used are chosen so that subsequent conditional  
execution of ARM instructions can test the predicates defined in the IEEE 754 standard.  
Underflow  
The Cortex-R4F FPU uses the before rounding form of tininess and the inexact result form of  
loss of accuracy as described in the IEEE 754 standard to generate Underflow exceptions.  
In flush-to-zero mode, results that are tiny before rounding, as described in the IEEE 754  
standard, are flushed to a zero, and the UFC flag, FPSCR[3], is set. See the ARM Architecture  
Reference Manual for information on flush-to-zero mode.  
When the FPU is not in flush-to-zero mode, operations are performed on subnormal operands.  
If the operation does not produce a tiny result, it returns the computed result, and the UFC flag,  
FPSCR[3], is not set. The IXC flag, FPSCR[4], is set if the operation is inexact. If the operation  
produces a tiny result, the result is a subnormal or zero value, and the UFC flag, FPSCR[3], is  
set if the result was also inexact.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
12-12  
   
FPU Programmer’s Model  
12.5.3 Exceptions  
The FPU implements the VFPv3 architecture and sets the cumulative exception status flag in  
the FPSCR register as required for each instruction. The FPU does not support user-mode traps.  
The exception enable bits in the FPSCR read-as-zero, and cannot be written. The processor also  
has six output pins, FPIXC, FPUFC, FPOFC, FPDZC, FPIDC, and FPIOC, that each reflect  
the status of one of the cumulative exception flags. See FPU signals on page A-23 for a  
description of these outputs. You can mask each of these outputs masked by setting the  
corresponding bit in the Secondary Auxiliary Control Register.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
12-13  
Chapter 13  
Integration Test Registers  
This chapter describes how to use the Integration Test Registers in the processor. It contains the  
following sections:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
13-1  
   
Integration Test Registers  
13.1 About Integration Test Registers  
The processor contains Integration Test Registers that enable you to verify integration of the  
design and enable topology detection of the design using debug tools. The Integration Mode  
Control Register (ITCTRL), which is also described in this chapter, controls the use of the  
Integration Test Registers.  
When programming the Integration Test Registers you must enable all the changes at the same  
time.  
For more information about the Integration Test Registers and the Integration Mode Control  
Register see the ARM Architecture Reference Manual.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
13-2  
   
Integration Test Registers  
13.2 Programming and reading Integration Test Registers  
The Integration Test Registers are programmed using the debug APB interface. For more  
information on using the debug APB interface see Chapter 11 Debug.  
13.2.1 Software access using APB  
APB provides a direct method of programming:  
a stand-alone macrocell  
a macrocell in a CoreSight system.  
APB provides access to the programmable control registers of peripheral devices. It has these  
features:  
unpipelined protocol, that is, a second transfer cannot start before the first transfer  
completes  
every transfer takes at least two cycles.  
For more information on APB transfers see AMBA 3 APB Protocol v1.0 Specification.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
13-3  
   
Integration Test Registers  
13.3 Summary of the processor registers used for integration testing  
Table 13-1 lists the processor Integration Test Registers and the Integration Mode Control  
Register (ITCTRL).  
Table 13-1 Integration Test Registers summary  
Register  
name  
Base  
offset  
Default  
value  
Clock  
domain  
Type  
Description  
Integration Test Registers  
a
ITETMIF  
0xED8  
0xEF8  
WO  
WO  
CLK  
CLK  
-
ITMISCOUT  
n/a  
a
ITMISCIN  
0xEFC  
RO  
CLK  
CLK  
-
Integration Mode Control Register  
ITCTRL 0xF00  
0
R/W  
a. See the register description for this value.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
13-4  
         
Integration Test Registers  
13.4 Processor integration testing  
This section describes the behavior and use of the Integration Test Registers that are in the  
processor. It also describes the Integration Mode Control Register that controls the use of the  
Integration Test Registers. For more information about the ITCTRL see the ARM Architecture  
Reference Manual.  
If you want to access these registers you must first set bit [0] of the Integration Mode Control  
Register to 1.  
You can use the write-only Integration Test Registers to set the outputs of some of the  
processor signals. Table 13-2 shows the signals that you can write in this way.  
You can use the read-only Integration Test Registers to read the state of some of the  
processor inputs. Table 13-3 on page 13-6 shows the signals that you can read in this way.  
There are Integration Test Registers that you can use in conjunction with ETM-R4 integration.  
For more information see the ETM-R4 Technical Reference Manual  
Table 13-2 Output signals that can be controlled by the Integration Test Registers  
Signal  
Register  
Bit  
Register description  
DBGRESTARTED  
DBGTRIGGER  
ITMISCOUT [9]  
ITMISCOUT [8]  
ETMWFIPENDING ITMISCOUT [5]  
nPMUIRQ  
ITMISCOUT [4]  
ITMISCOUT [2]  
ITMISCOUT [1]  
ITMISCOUT [0]  
COMMTX  
COMMRX  
DBGACK  
EVNTBUS[46]  
EVNTBUS[28, 0]  
ETMCID[31, 0]  
ETMDA[31, 0]  
ETMDCTL[11, 0]  
ETMDD[63, 0]  
ETMIA[31, 1]  
ETMICTL[13, 0]  
ITETMIF  
ITETMIF  
ITETMIF  
ITETMIF  
ITETMIF  
ITETMIF  
ITETMIF  
ITETMIF  
[14]  
[13:12]  
[11:10]  
[7:6]  
[5:4]  
[9:8]  
[3:2]  
[1:0]  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
13-5  
       
Integration Test Registers  
Table 13-3 Input signals that can be read by the Integration Test Registers  
Signal  
Register  
Bit  
Register description  
DBGRESTART  
ITMISCIN [11]  
ETMEXTOUT[1:0] ITMISCIN [9:8]  
nETMWFIREADY  
nIRQ  
ITMISCIN [5]  
ITMISCIN [2]  
ITMISCIN [1]  
ITMISCIN [0]  
nFIQ  
EDBGRQ  
This section describes:  
13.4.1 Using the Integration Test Registers  
When bit [0] of the Integration Mode Control Register (ITCTRL) is set to b1:  
Values written to the write-only Integration Test Registers map onto the specified outputs  
of the macrocell. For example, writing b1to ITMISCOUT[0] causes DBGACK to be  
asserted HIGH.  
Values read from the read-only Integration Test Registers correspond to the values of the  
specified inputs of the macrocell. For example, if you read ITMISCIN[9:8] you obtain  
the value of ETMEXTOUT[1:0].  
13.4.2 Performing integration testing  
When you perform integration testing or topology detection:  
You must ensure that the other ETM interface signals cannot change value during  
integration testing.  
ARM strongly recommends that the processor is halted while in debug state, because  
toggling input and output pins might have an unwanted effect on the operation of the  
processor. You must not set the ITCTRL Register until the processor has halted.  
When the ITCTRL Register is set, the ETM interface stops trace output, and outputs the  
data written into the relevant integration registers.  
After you perform integration testing or topology detection, that is, the Integration Mode  
Control Register has been set, the system must be reset. This is because the signals that are  
toggled can have an unwanted effect on connected devices.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
13-6  
       
Integration Test Registers  
13.4.3 ITETMIF Register (ETM interface)  
The ITETMIF Register at offset 0xED8is write-only. Figure 13-1 shows the register bit  
assignments.  
31  
15 14 13 12 11 10 9  
8
7
6
5
4
3
2
1
0
Reserved  
EVNTBUS[46]  
ETMICTL[0]  
ETMICTL[13]  
ETMIA[1]  
EVNTBUS[28]  
EVNTBUS[0]  
ETMCID[31]  
ETMCID[0]  
ETMDD[63]  
ETMDD[0]  
ETMIA[31]  
ETMDCTL[0]  
ETMDCTL[11]  
ETMDA[0]  
ETMDA[31]  
Figure 13-1 ITETMIF Register bit assignments  
Table 13-4 shows the fields when writing the ITETMIF Register. When this register is written  
the appropriate output pins take the value written.  
Table 13-4 ITETMIF Register bit assignments  
Bits  
Name  
Function  
[31:15]  
[14]  
[13]  
[12]  
[11]  
[10]  
[9]  
-
Reserved. Write as zero.  
Set value of the EVNTBUS[46] output pina.  
Set value of the EVNTBUS[28] output pin.  
Set value of the EVNTBUS[0] output pin.  
Set value of the ETMCID[31] output pin.  
Set value of the ETMCID[0] output pin.  
Set value of the ETMDD[63] output pin.  
Set value of the ETMDD[0] output pin.  
Set value of the ETMDA[31] output pin.  
Set value of the ETMDA[0] output pin.  
EVNTBUS[46]  
EVNTBUS[28]  
EVNTBUS[0]  
ETMCID[31]  
ETMCID[0]  
ETMDD[63]  
ETMDD[0]  
ETMDA[31]  
ETMDA[0]  
[8]  
[7]  
[6]  
[5]  
ETMDCTL[11] Set value of the ETMDCTL[11] output pin.  
[4]  
ETMDCTL[0]  
ETMIA[31]  
Set value of the ETMDCTL[0] output pin.  
Set value of the ETMIA[31] output pin.  
Set value of the ETMIA[1] output pin.  
Set value of the ETMICTL[13] output pin.  
Set value of the ETMICTL[0] output pin.  
[3]  
[2]  
ETMIA[1]  
[1]  
ETMICTL[13]  
ETMICTL[0]  
[0]  
a. Not available on r0px revisions of the processor.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
13-7  
         
Integration Test Registers  
13.4.4 ITMISCOUT Register (Miscellaneous Outputs)  
The ITMISCOUT Register at offset 0xEF8is write-only. Figure 13-2 shows the register bit  
assignments.  
31  
10 9  
8
7
6
5
4
3
2
1
0
Reserved  
DBGRESTARTED  
DBGTRIGGER  
Reserved  
ETMWFIPENDING  
nPMUIRQ  
Reserved  
COMMTX  
COMMRX  
DBGACK  
Figure 13-2 ITMISCOUT Register bit assignments  
Table 13-5 shows the fields when writing the ITMISCOUT Register. When this register is  
written the appropriate output pins take the value written.  
Table 13-5 ITMISCOUT Register bit assignments  
Bits  
Name  
Function  
[31:10]  
[9]  
-
Reserved. Write as zero.  
DBGRESTARTED  
Set value of the DBGRESTARTED output pin.  
Set value of the DBGTRIGGER output pin.  
Reserved. Write as zero.  
[8]  
DBGTRIGGER  
-
[7:6]  
[5]  
ETMWFIPENDING Set value of the ETMWFIPENDING output pin.  
[4]  
nPMUIRQ  
-
Set value of nPMUIRQ output pin.  
Reserved. Write as zero.  
[3]  
[2]  
COMMTX  
COMMRX  
DBGACK  
Set value of COMMTX output pin.  
Set value of COMMRX output pin.  
Set value of the DBGACK output pin.  
[1]  
[0]  
13.4.5 ITMISCIN Register (Miscellaneous Inputs)  
The ITMISCIN Register at offset OxEFCis read-only. Figure 13-3 on page 13-9 shows the  
register bit assignments.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
13-8  
           
Integration Test Registers  
31  
12 11 10 9  
8
7
6
5
4
3
2
1
0
Reserved  
DBGRESTART  
Reserved  
ETMEXTOUT[1:0]  
Reserved  
nETMWFIREADY  
Reserved  
nFIQ  
nIRQ  
EDBGRQ  
Figure 13-3 ITMISCIN Register bit assignments  
Table 13-6 lists the register bit assignments for the ITMISCIN Register.  
Table 13-6 ITMISCIN Register bit assignments  
Bits  
Name  
Function  
[31:12]  
[11]  
-
Reserved. Read Undefined.  
DBGRESTART  
Read value of the DBGRESTART input pin.  
Reserved. Read Undefined.  
[10]  
-
[9:8]  
[7:6]  
[5]  
ETMEXTOUT  
-
Read value of the ETMEXTOUT[1:0] input pins.  
Reserved. Read Undefined.  
nETMWFIREADY Reads the nETMWFIREADY input pin. Although this pin is active LOW, the value of  
this bit matches the physical state of the signal:  
0 = input pin is LOW (asserted)  
1 = input pin is HIGH (deasserted).  
[4:3]  
[2]  
-
Reserved. Read Undefined.  
nFIQ  
nIRQ  
EDBGRQ  
Read value of nFIQ input pin.  
Read value of nIRQ input pin.  
Read value of EDBGRQ input pin.  
[1]  
[0]  
13.4.6 Integration Mode Control Register (ITCTRL)  
The ITCTRL Register, register 0x3C0at offset 0xF00, is read/write. Figure 13-4 shows the  
register bit assignments.  
31  
1
0
Reserved  
INTMODE  
Figure 13-4 ITCTRL Register bit assignments  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
13-9  
               
Integration Test Registers  
Table 13-7 shows the fields of the ITCTRL Register.  
Table 13-7 ITCTRL Register bit assignments  
Bits  
[31:1] RAZ/SBZP  
[0] R/W  
Access  
Reset value Name  
Function  
-
-
Reserved.  
0
INTMODE Controls whether the processor is in normal operating mode or  
integration mode:  
b0 = normal operation  
b1 = integration mode enabled.  
Writing to the ITCTRL register controls whether the processor is in its default functional mode,  
or in integration mode, where the inputs and outputs of the device can be directly controlled for  
the purpose of integration testing or topology detection. For more information see the ARM  
Architecture Reference Manual.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
13-10  
   
Cycle Timings and Interlock Behavior  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-2  
Cycle Timings and Interlock Behavior  
14.1 About cycle timings and interlock behavior  
Complex instruction dependencies and memory system interactions make it impossible to  
describe briefly the exact cycle timing behavior for all instructions in all circumstances. The  
timings described in this chapter are accurate in most cases. If precise timings are required, you  
must use a cycle-accurate model of the processor.  
Unless stated otherwise, cycle counts and result latencies that this chapter describes are  
best-case numbers. They assume:  
no outstanding data dependencies between the current instruction and a previous  
instruction  
the instruction does not encounter any resource conflicts  
all data accesses hit in the data cache, and do not cross protection region boundaries  
all instruction accesses hit in the instruction cache.  
This section describes:  
14.1.1 Instruction execution overview  
The instruction execution pipeline has four stages, Iss, Ex1, Ex2, and Wr.  
Extensive forwarding to the end of the Iss, Ex1, and Ex2 stages enables many dependent  
instruction sequences to run without pipeline stalls. General forwarding occurs from the end of  
the Ex2 and Wr pipeline stages. In addition, the multiplier contains an internal multiply  
accumulate forwarding path. The address generation unit also contains an internal forwarding  
path.  
Most instructions do not require a register until the Ex2 stage. All result latencies are given as  
the number of cycles until the register is available for a following instruction in the Ex2 stage.  
Most ALU operations require their source registers at the start of the Ex2 stage, and have a result  
latency of one. For example, the following sequence takes two cycles:  
ADD R1,R3,R4  
ADD R5,R2,R1  
;Result latency one  
;Register R1 required by ALU  
The PC is the only register that result latency does not affect. An instruction that alters the PC  
never causes a pipeline stall because of interlocking with a subsequent instruction that reads the  
PC.  
Most loads have a result latency of two or higher as they do not forward their results until the  
Wr stage. For example, the following sequence takes three cycles:  
LDR R1, [R2]  
;Result latency two  
ADD R3, R3, R1  
;Register R1 required by ALU  
If a subsequent instruction requires the register at the end of the Iss stage then an extra cycle  
must be added to the result latency of the instruction producing the required register.  
Instructions that require a register at the end of these stages are specified by describing that  
register as an Early Reg. The following sequence, requiring an Early Reg, takes four cycles:  
LDR R1, [R2]  
;Result latency two  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-3  
     
Cycle Timings and Interlock Behavior  
ADD R3, R3, R1 LSL#6  
;plus one because Register R1 is Early  
The following sequence where R1 is a Late Reg takes two cycles:  
LDR R1, [R2]  
STR R1, [R3]  
;Result latency two minus one cycles  
;no penalty because R1 is a Late register  
The following sequence where R1 is a Very Early Reg takes four cycles:  
ADD R3, R1, R2  
LDR R4, [R3]  
;Result latency one plus two cycles  
;plus two because register R3 is Very Early  
14.1.2 Conditional instructions  
Most instructions do not take more or fewer cycles to execute if they fail their condition codes.  
The exceptions to this are:  
instructions that alter the PC, such as branches  
integer divide instructions, which require only one execute cycle.  
The result latency of most instructions that fail their condition codes is one. The exceptions to  
this are:  
all load and store instructions, which have their result latency unaffected  
integer divide instructions, which have a result latency of three.  
14.1.3 Flag-setting instructions  
Most instructions do not take more or fewer cycles to execute if they are flag-setting. The  
exceptions to this are certain multiply instructions.  
14.1.4 Definition of terms  
Table 14-1 gives descriptions of cycle timing terms used in this chapter.  
Table 14-1 Definition of cycle timing terms  
Term  
Description  
Memory Cycles This is the number of cycles during which an instruction sends a memory access to the cache.  
Cycles  
This is the minimum number of cycles required to issue an instruction. Issue cycles that produce  
memory accesses to the cache are included, so Cycles is always greater than or equal to Memory  
Cycles.  
Result Latency  
This is the number of cycles before the result of this instruction is available to a Normal Reg of the  
following instruction. When the Result Latency of an instruction is greater than Cycles and the  
following instruction requires the result, the following instruction stalls for a number of cycles equal  
to Result Latency minus Cycles.  
Note  
The Result Latency is counted from the first cycle of an instruction.  
Normal Reg  
Late Reg  
The specified registers are required at the start of the Ex2 stage.  
The specified registers are not required until the start of the Wr stage. Subtract one cycle from the  
Result Latency of the instruction producing this register.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-4  
         
Cycle Timings and Interlock Behavior  
Table 14-1 Definition of cycle timing terms (continued)  
Term  
Description  
Early Reg  
The specified registers are required at the start of the Ex1 stage. Add one cycle to the Result Latency  
of the instruction producing this register.  
Very Early Reg  
Interlock  
The specified registers are required at the start of the Iss stage. Add two cycles to the Result Latency  
of the instruction producing this register, or one cycle if the instruction producing this register is an LDM  
LDREX, or LDRT. The lower Result Latency does not apply if this register is the base register of  
the load instruction producing this register, or if the load instruction is an LDRB  
,
LDR LDRD,  
,
,
LDRBT, LDRH, LDRSB, or  
LDRSH  
.
There is a data dependency between two instructions in the pipeline, resulting in the Iss stage being  
stalled until the processor resolves the dependency.  
14.1.5 Assembler language syntax  
The syntax used throughout this chapter is unified assembler and the timings apply to ARM and  
Thumb instructions.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-5  
 
Cycle Timings and Interlock Behavior  
14.2 Register interlock examples  
Table 14-2 shows register interlock examples using LDRand ADDinstructions.  
LDRinstructions take one cycle, have a result latency of two, and require their base register as a  
Very Early Reg.  
ADDinstructions take one cycle and have a result latency of one.  
Table 14-2 Register interlock examples  
Instruction  
sequence  
Behavior  
LDR R1, [R2]  
ADD R6, R5, R4  
Takes two cycles because there are no register dependencies.  
Takes two cycles because ADDinstructions have a result latency of one.  
Takes three cycles because of the result latency of R1.  
Takes four cycles because of the use of the result of R2 as a Very Early Reg.  
ADD R1, R2, R3  
ADD R9, R6, R1  
LDR R1, [R2]  
ADD R6, R5, R1  
ADD R2, R5, R6  
LDR R1, [R2]  
LDR R1, [R2]  
LDR R5, [R1]  
Takes four cycles because of the result latency of R1, the use of the result of R1 as a Very Early Reg,  
and the use of an LDR to generate R1.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-6  
       
Cycle Timings and Interlock Behavior  
14.3 Data processing instructions  
This section describes the cycle timing behavior for the ADC  
,
ADD  
,
ADDW  
,
AND  
,
ASR, BIC, CLZ, CMN, CMP,  
EOR  
,
LSL  
,
LSR  
,
MOV  
,
MOVT  
,
MOVW  
,
MVN  
,
ORN  
,
ORR  
,
ROR  
,
RRX  
,
RSB  
,
RSC SBC  
,
,
SUB  
,
SUBW TEQ, and TST  
,
instructions.  
This section describes:  
14.3.1 Cycle counts if destination is not PC  
Table 14-3 shows the cycle timing behavior for data processing instructions if their destination  
is not the PC. You can substitute ADDwith any of the data processing instructions identified in  
the opening paragraph of this section.  
Table 14-3 Data Processing Instruction cycle timing behavior if destination is not PC  
Early  
Reg  
Late Result  
Example instruction  
Cycles  
Comments  
Reg  
latency  
ADD <Rd>, <Rn>, #<immed>  
ADD <Rd>, <Rn>, <Rm>  
1
1
1
1
-
-
-
-
-
1
1
1
1
Normal cases.  
-
ADD <Rd>, <Rn>, <Rm>, LSL #<immed>  
<Rm>  
Requires a shifted source register.  
ADD <Rd>, <Rn>, <Rm>, LSL <Rs  
>
<Rm>  
,
<Rs>  
Requires a register controlled  
shifted source register.  
MOV <Rd>, <Rm>  
1
-
<Rm>  
1
Simple MOVcase. Must not set the  
flags or require a shifted source  
register.  
14.3.2 Cycle counts if destination is the PC  
Table 14-4 shows the cycle timing behavior for data processing instructions if their destination  
is the PC. You can substitute ADD with any data processing instruction except for a CLZ. A CLZ  
with the PC as the destination is an Unpredictable instruction.  
For condition code failing cycle counts, the cycles for the non-PC destination variants must be  
used.  
Table 14-4 Data Processing instruction cycle timing behavior if destination is the PC  
Early Late Result  
Example instruction  
Cycles  
Comments  
Reg  
Reg  
latency  
ADD pc, <Rn>, #<immed>  
ADD pc, <Rn>, <Rm>  
9
9
9
9
-
-
-
-
-
-
-
-
-
Normal cases to PC  
-
ADD pc, <Rn>, <Rm>, LSL #<immed>  
<Rm>  
Requires a shifted source register  
ADD pc, <Rn>, <Rm>, LSL <Rs  
>
<Rm>  
,
Requires a register controlled shifted  
source register  
<Rs>  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-7  
               
Cycle Timings and Interlock Behavior  
14.3.3 Example interlocks  
Most data processing instructions are single-cycle and can be executed back-to-back without  
interlock cycles, even if there are data dependencies between them. The exceptions to this are  
when shifts are used.  
Shifter  
The registers that the shifter requires are Early Regs and require an additional cycle of result  
availability before use. For example, the following sequence introduces a 1-cycle interlock, and  
takes three cycles to execute:  
ADD R1,R2,R3  
ADD R4,R5,R1 LSL #1  
The second source register, which is not shifted, does not incur an extra data dependency check.  
Therefore, the following sequence takes two cycles to execute:  
ADD R1,R2,R3  
ADD R4,R1,R9 LSL #1  
Register controlled shifts  
The register containing the shift distance is an Early Reg. For example, the following sequence  
takes three cycles to execute:  
ADD R1, R2, R3  
ADD R4, R2, R4, LSL R1  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-8  
 
Cycle Timings and Interlock Behavior  
14.4 QADD, QDADD, QSUB, and QDSUB instructions  
This section describes the cycle timing behavior for the QADD QDADD, QSUB, and QDSUBinstructions.  
,
These instructions perform saturating arithmetic. They have a result latency of two. The QDADD  
and QDSUBinstructions must double and saturate the register <Rn>before the addition. This  
register is an Early Reg.  
Table 14-5 shows the cycle timing behavior for QADD QDADD, QSUB, and QDSUBinstructions.  
,
Table 14-5 QADD, QDADD, QSUB, and QDSUB instruction cycle timing behavior  
Instructions Cycles Early Reg Result latency  
QADD  
,
QSUB  
QDSUB  
1
1
-
2
2
QDADD  
,
<Rn>  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-9  
       
Cycle Timings and Interlock Behavior  
14.5 Media data-processing  
Table 14-6 shows media data-processing instructions and gives their cycle timing behavior.  
All media data-processing instructions are single-cycle issue instructions. These instructions  
have result latencies of one or two cycles. Some of the instructions require an input register to  
be shifted, or manipulated in some other way before use and therefore are marked as requiring  
an Early Reg.  
Table 14-6 Media data-processing instructions cycle timing behavior  
Instructions  
Cycles  
Early Reg  
Result latency  
SADD16  
UADD16  
SEL  
,
SSUB16  
,
,
SADD8  
,
,
SSUB8  
USUB8  
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
-
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
1
1
1
,
USUB16  
UADD8  
-
-
QADD16  
,
QSUB16  
,
QADD8  
,
QSUB8  
-
SHADD16  
UQADD16  
UHADD16  
,
,
,
SHSUB16  
UQSUB16  
UHSUB16  
,
,
,
SHADD8  
UQADD8  
UHADD8  
,
,
,
SHSUB8  
UQSUB8  
UHSUB8  
-
-
-
SSAT16  
,
USAT16  
<Rn>  
SASX  
,
,
SSAX  
USAX  
-
UASX  
-
SXTAB  
,
SXTAB16  
,
SXTAH  
<Rm>  
a
SXTB  
,
,
SXTB16  
,
,
SXTH  
UXTH  
<Rm>  
a
UXTB  
UXTB16  
<Rm>  
UXTAB  
REV REV16  
PKHBT PKHTB  
USAT  
QSAX  
,
UXTAB16  
,
UXTAH  
RBIT  
<Rm>  
,
,
REVSH  
,
<Rm>  
,
<Rm>  
SSAT  
,
,
<Rm>  
QASX  
-
SHASX  
UQASX  
UHASX  
BFC  
,
SHSAX  
UQSAX  
UHSAX  
-
,
,
-
-
<Rd>  
SBFX  
,
UBFX  
<Rn>  
BFI  
<Rd>, <Rn>  
a. A shift of zero makes <Rm>a Normal Reg for these instructions.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-10  
         
Cycle Timings and Interlock Behavior  
14.6 Sum of Absolute Differences (SAD)  
Table 14-7 shows SADinstructions and gives their cycle timing behavior.  
Table 14-7 Sum of absolute differences instruction timing behavior  
Instructions Cycles  
Early Reg  
Result latency  
2a  
2a  
USAD8  
1
1
<Rn>, <Rm>  
<Rn>, <Rm>  
USADA8  
a. Result latency is one fewer if the destination is the  
accumulate for a subsequent USADA8  
.
14.6.1 Example interlocks  
Table 14-8 shows interlock examples using USAD8and USADA8instructions.  
Table 14-8 Example interlocks  
Instruction sequence Behavior  
USAD8 R1,R2,R3  
ADD R5,R6,R1  
Takes three cycles because USAD8has a Result Latency of two, and the ADDrequires  
the result of the USAD8instruction.  
USAD8 R1,R2,R3  
MOV R9,R9  
ADD R5,R6,R1  
Takes three cycles. The MOVinstruction is scheduled during the Result Latency of  
the USAD8 instruction.  
USAD8 R1,R2,R3  
USADA8 R1,R4,R5,R1  
Takes two cycles. The Result Latency is one less because the result is used as the  
accumulate for a subsequent USADA8instruction.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-11  
           
Cycle Timings and Interlock Behavior  
14.7 Multiplies  
Most multiply operations cannot forward their result early, except as the accumulate value for a  
subsequent multiply. For a subsequent multiply accumulate the result is available one cycle  
earlier than for all other uses of the result.  
Certain multiplies require:  
more than one cycle to execute  
more than one pipeline issue to produce a result.  
The multiplicand and multiplier are required as Early Regs because they are both required at the  
end of the Iss stage.  
Flag-setting multiplies followed by a conditional instruction interlock the conditional  
instruction for one cycle, or two cycles if the instruction is a conditional multiply. Flag-setting  
multiplies followed by a flag-setting instruction interlock the flag-setting instruction for one  
cycle, unless the instruction is a flag-setting multiply in which case there is no interlock.  
Table 14-9 shows the cycle timing behavior of example multiply instructions.  
Table 14-9 Example multiply instruction cycle timing behavior  
Example  
instruction  
Cycles Early Reg  
Late Reg  
Result latency  
MUL(S)  
2
2
2
2
2
2
1
1
1
1
2
1
1
1
1
2
2
2
<Rn>, <Rm>  
<Rn>, <Rm>  
<Rn>, <Rm>  
<Rn>, <Rm>  
<Rn>, <Rm>  
<Rn>, <Rm>  
<Rn>, <Rm>  
<Rn>, <Rm>  
<Rn>, <Rm>  
<Rn>, <Rm>  
<Rn>, <Rm>  
<Rn>, <Rm>  
<Rn>, <Rm>  
<Rn>, <Rm>  
<Rn>, <Rm>  
<Rn>, <Rm>  
<Rn>, <Rm>  
<Rn>, <Rm>  
-
3
MLA(S)  
,
MLS  
<Ra>  
3
SMULL(S)  
UMULL(S)  
SMLAL(S)  
UMLAL(S)  
SMULxy  
-
3, 3  
3, 3  
3, 3  
3, 3  
2
-
<RdLo>, <RdHi>  
<RdLo>, <RdHi>  
-
SMLAxy  
-
2
SMULWy  
-
2
SMLAWy  
-
2
SMLALxy  
<RdLo>, <RdHi>  
3, 3  
2
SMUAD  
SMLAD  
SMUSD  
SMLSD  
SMMUL  
SMMLA  
SMMLS  
,
,
,
,
,
,
,
SMUADX  
SMLADX  
SMUSDX  
SMLSDX  
SMMULR  
SMMLAR  
SMMLSR  
-
-
2
-
2
-
2
-
3
<Ra>  
<Ra>  
3
3
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-12  
       
Cycle Timings and Interlock Behavior  
Table 14-9 Example multiply instruction cycle timing behavior (continued)  
Example  
Cycles Early Reg  
Late Reg  
Result latency  
instruction  
SMLALD  
SMLSLD  
UMAAL  
,
,
SMLALDX  
SMLSLDX  
1
1
2
<Rn>, <Rm>  
<Rn>, <Rm>  
<Rn>, <Rm>  
-
2, 2  
2, 2  
3, 3  
-
<RdLo>, <RdHi>  
Note  
Result Latency is one less if the result is used as the accumulate value for a subsequent multiply  
accumulate. This only applies if the result is the same width as the accumulate value, that is 32  
or 64 bits.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-13  
Cycle Timings and Interlock Behavior  
14.8 Divide  
This section describes the cycle timing behavior of the UDIVand SDIVinstructions.  
The divider unit is separate to the main execute pipeline so the UDIVand SDIVinstructions require  
one cycle to issue. They execute out-of-order relative to the rest of the pipeline, and require an  
additional issue cycle at the end of the divide operation to write the result to the destination  
register. This additional cycle is not required if the divide instruction fails its condition code.  
Result Latency for a UDIVinstruction A divided by B is given by:  
clz(B) - clz(A) + 1  
Result latency = 3 + max  
,0  
((  
) )  
2
Result Latency for a SDIVinstruction A divided by B is given by:  
clz(B) - clz(A) + 1  
Result latency = 4 + max  
,0  
((  
) )  
2
Note  
A divide instruction that fails its condition code or attempts to divide by zero has a Result  
Latency of three.  
The value of the (clz(B) - clz(A) + 1)/2 component of these equations must be rounded  
down.  
The clz(x) function counts the number of leading zeros in the 32-bit value x. If x is  
negative, it is negated before this count occurs.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-14  
   
Cycle Timings and Interlock Behavior  
14.9 Branches  
This section describes the cycle timing behavior for the  
B
,
BL, BLX, BX, BXJ, CBNZ, CBZ, TBB, and TBH  
instructions. Branches are subject to dynamic and return stack predictions. Table 14-10 shows  
example branch instructions and their cycle timing behavior.  
Table 14-10 Branch instruction cycle timing behavior  
Memory  
cycles  
Example instruction  
Cycles  
Comments  
B<label>, BL<label>a,  
1
8
1
9
1
8
9
1
9
9
1
9
1
8
9
9
9
9
-
Correct dynamic prediction  
Incorrect dynamic prediction  
Correct return stack prediction  
Incorrect return stack prediction  
Correct condition prediction and correct return stack prediction  
Incorrect condition prediction  
Correct condition prediction and incorrect return stack prediction  
Condition code fails  
a
BLX<label>  
-
b
-
BX <Rm>  
-
b
-
BX <cond> <Rm>  
-
-
BXJ <cond> <Rm>  
-
-
Condition code passes  
BLX <Rm>  
-
-
BLX <cond> <Rm>  
-
Condition code fails  
-
Condition code passes  
CBZ <Rn>, <label>  
,
CBNZ  
-
Correct condition prediction  
Incorrectly predicted  
<Rn>, <label>  
-
c
1
1
1
1
Condition code fails  
TBB [<Rn>, <Rm>]  
Condition code passes  
c
Condition code fails  
TBH [<Rn>, <Rm>, LSL#1]  
Condition code passes  
a. Return stack push.  
b. Return stack pop, if condition passes.  
c. <Rn>and <Rm>are Very Early Regs.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-15  
         
Cycle Timings and Interlock Behavior  
14.10 Processor state updating instructions  
This section describes the cycle timing behavior for the MSR MRS, CPS, and SETENDinstructions.  
,
Table 14-11 shows processor state updating instructions and their cycle timing behavior.  
Table 14-11 Processor state updating instructions cycle timing behavior  
Instruction  
Cycles Comments  
MRS  
1
5
1
1
1
1
All MRSinstructions  
MSR  
All other MSRinstructions to the CPSR  
All MSRinstructions to the SPSR  
Interrupt masks only  
Mode changing  
MSR SPSR  
CPS <effect> <iflags>  
CPS <effect> <iflags>, #<mode>  
SETEND  
-
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-16  
       
Cycle Timings and Interlock Behavior  
14.11 Single load and store instructions  
This section describes the cycle timing behavior for LDR  
,
LDRHT, LDRSBT, LDRSHT, LDRT, LDRB, LDRBT,  
LDRSB LDRH, LDRSH, STR, STRT, STRB, STRBT,  
,
STRH, and PLDinstructions.  
Table 14-12 shows the cycle timing behavior for stores and loads, other than loads to the PC.  
You can replace LDRwith any of these single load or store instructions. The following rules  
apply:  
They are normally single-cycle issue. Both the base and any offset register are Very Early  
Regs.  
They are 3-cycle issue if pre-increment addressing with either a negative register offset or  
a shift other than LSL #1, 2 or 3 is used. Both the base and any offset register are Very  
Early Regs.  
If unaligned support is enabled then accesses to addresses not aligned to the access size  
that cross a 64-bit aligned boundary generate two memory accesses, and require an  
additional cycle to issue. This extra cycle is required if the final address is potentially  
unaligned, even if the final address turns out to be aligned.  
PLD (data preload hint instructions) have cycle timing behavior as for load instructions.  
Because they have no destination register, the result latency is not-applicable for such  
instructions.  
For store instructions <Rt>is always a Late Reg.  
Table 14-12 Cycle timing behavior for stores and loads, other than loads to the PC  
Result  
Memory Resultlatency latency  
Example instruction  
Cycles  
Comments  
cycles  
(LDR)  
(base  
register)  
a
a
a
a
1
3
2
4
1
1
2
2
2
4
3
5
1
3
2
4
Aligned access  
LDR <Rt>, <addr_md_1cycle>  
LDR <Rt>, <addr_md_3cycle>  
LDR <Rt>, <addr_md_1cycle>  
LDR <Rt>, <addr_md_3cycle>  
Aligned access  
Potentially unaligned access  
Potentially unaligned access  
a. See Table 14-14 on page 14-18 for an explanation of <addr_md_1cycle>and <addr_md_3cycle>  
.
Table 14-13 shows the cycle timing behavior for loads to the PC.  
Table 14-13 Cycle timing behavior for loads to the PC  
Memory Result  
Example instruction  
Cycles  
Comments  
cycles  
latency  
LDR pc, [sp, #<imm>] (!)  
LDR pc, [sp], #<imm>  
LDR pc, [sp, #<imm>] (!)  
LDR pc, [sp], #<imm>  
1
1
9
9
1
1
1
1
-
-
-
-
Correctly return stack predicted, or conditional  
predicted correctly  
Return stack mispredicted, conditional predicted  
correctly  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-17  
           
Cycle Timings and Interlock Behavior  
Table 14-13 Cycle timing behavior for loads to the PC (continued)  
Memory Result  
Comments  
Example instruction  
Cycles  
cycles  
latency  
LDR <cond> pc, [sp, #<imm>]  
(!)  
8
1
-
Conditional predicted incorrectly, but return  
stack predicted correctly  
LDR <cond> pc, [sp], #cn  
s
8
1
1
1
-
-
-
a
9
-
-
LDR pc, <addr_md_1cycle>  
LDR pc, <addr_md_3cycle>a  
11  
a. See Table 14-14 for an explanation of <addr_md_1cycle>and <addr_md_3cycle>. For condition code failing cycle counts, you  
must use the cycles for the non-PC destination variants.  
Only cycle times for aligned accesses are given because Unaligned accesses to the PC are not  
supported.  
The processor includes a 4-entry return stack that can predict procedure returns. Any LDR  
instruction to the PC with an immediate post-indexed offset of plus four, and the stack pointer  
R13 as the base register is considered a procedure return.  
Table 14-14 shows the explanation of <addr_md_1cycle>and <addr_md_3cycle>used in  
Table 14-14 <addr_md_1cycle> and <addr_md_3cycle> LDR example instruction explanation  
Example instruction  
Very Early Reg Comments  
<addr_md_1cycle>  
LDR <Rt>, [<Rn>, #<imm>] (!)  
LDR <Rt>, [<Rn>, <Rm>] (!)  
LDR <Rt>, [<Rn>, <Rm>, LSL #1, 2 or 3] (!)  
LDR <Rt>, [<Rn>], #<imm>  
<Rn>  
If post-increment addressing or pre-increment  
addressing with an immediate offset, or a  
positive register offset with no shift or shift  
LSL #1, 2 or 3, then 1-issue cycle  
<Rn>, <Rm>  
<Rn>, <Rm>  
<Rn>  
LDR <Rt>, [<Rn>], +/-<Rm>  
<Rn>, <Rm>  
<Rn>, <Rm>  
LDR <Rt>, [<Rn>], +/-<Rm> <shift> <cns>  
<addr_md_3cycle>  
LDR <Rt>, [<Rn>, -<Rm>] (!)  
LDR <Rt>, [Rn, +/-<Rm> <shift> <cns>] (!)  
<Rn>,<Rm>  
<Rn>,<Rm>  
If pre-increment addressing with a negative  
register offset or shift other than LSL #1, 2 or  
3, then 3-issue cycles  
14.11.1 Base register update  
The base register update for load or store instructions occurs in the ALU pipeline. To prevent an  
interlock for back-to-back load or store instructions reusing the same base register, there is a  
local forwarding path to recycle the updated base register around the address generator. This  
only applies when the load or store instruction with base write-back uses pre-increment  
addressing, and is a single load or store instruction that is not a load or store double instruction  
or load or store multiple instruction.  
For example, with R2aligned the following instruction sequence take three cycles to execute:  
LDR R5, [R2, #4]!  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-18  
   
Cycle Timings and Interlock Behavior  
LDR R6, [R2, #0X10]!  
LDR R7, [R2, #0X20]!  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-19  
Cycle Timings and Interlock Behavior  
14.12 Load and Store Double instructions  
This section describes the cycle timing behavior for the LDRDand STRDinstructions.  
The LDRDand STRDinstructions:  
Are normally single-cycle issue. Both the base and any offset register are Very Early Regs.  
Are 3-cycle issue if offset or pre-increment addressing with a negative register offset is  
used. Both the base and any offset register are Very Early Regs.  
Take only one memory cycle if the address is doubleword aligned.  
Take two memory cycles if the address is not doubleword aligned.  
Table 14-15 shows the cycle timing behavior for LDRDand STRDinstructions.  
Table 14-15 Load and Store Double instructions cycle timing behavior  
Result  
latency  
(LDRD)  
Cycles with  
base writeback cycles  
Memory  
Result latency  
(base register)  
Example instruction  
Cycles  
Address is doubleword aligned  
LDRD R0, R1, <addr_md_1cycle>  
LDRD R0, R1, <addr_md_3cycle>  
Address not doubleword aligned  
LDRD R0, R1, <addr_md_1cycle>  
LDRD R0, R1, <addr_md_3cycle>  
a
a
1
3
2
4
1
1
2, 2  
4, 4  
2
4
a
a
2
4
2
4
2
2
2, 3  
4, 5  
2
4
a. See Table 14-16 for an explanation of <addr_md_1cycle>and <addr_md_3cycle>  
.
Table 14-16 shows the explanation of <addr_md_1cycle>and <addr_md_3cycle>used in  
Table 14-16 <addr_md_1cycle> and <addr_md_3cycle> LDRD example instruction explanation  
Example instruction  
Very Early Reg Comments  
<addr_md_1cycle>  
LDRD <Rt>, <Rt2>, [<Rn>, #<imm>] (!)  
LDRD <Rt>, <Rt2>, [<Rn>, <Rm>] (!)  
LDRD <Rt>, <Rt2>, [<Rn>], #<imm>  
LDRD <Rt>, <Rt2>, [<Rn>], +/-<Rm>  
<addr_md_3cycle>  
<Rn>  
If post-increment addressing, pre-increment  
addressing with an immediate offset or a positive  
register offset, then 1-issue cycle  
<Rn>, <Rm>  
<Rn>  
<Rn>, <Rm>  
LDRD <Rt>, <Rt2>, [<Rn>, -<Rm>] (!)  
<Rn>,<Rm>  
If pre-increment addressing with a negative  
register offset, then 3-issue cycles  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-20  
           
Cycle Timings and Interlock Behavior  
14.13 Load and Store Multiple instructions  
This section describes the cycle timing behavior for the LDM STM, PUSH, and POPinstructions.  
,
These instructions take multiple cycles to issue, and then use multiple memory cycles to load  
and store all the registers. Because the memory datapath is 64-bits wide, two registers can be  
loaded or stored on each cycle.  
This section describes:  
14.13.1 Load and Store Multiples, other than load multiples including the PC  
In all cases the base register, <Rn>, is a Very Early Reg.  
Table 14-17 shows the cycle timing behavior of load and store multiples including the PC.  
Table 14-17 Cycle timing behavior of Load and Store Multiples, other than load multiples including the PC  
Cycles  
with base  
register  
Memory Result latency  
Result latency  
(base register)  
Example instruction  
Cycles  
cycles  
(LDM)  
write-back  
First address 64-bit aligned  
LDMIA <Rn>,{R1}  
1
1
2
2
3
3
4
1
2
2
3
3
4
4
1
1
2
2
3
3
4
2
1
2
2
3
3
4
4
LDMIA <Rn>,{R1,R2}  
2,2  
LDMIA <Rn>,{R1,R2,R3}  
2,2,3  
LDMIA <Rn>,{R1,R2,R3,R4}  
LDMIA <Rn>,{R1,R2,R3,R4,R5}  
LDMIA <Rn>,{R1,R2,R3,R4,R5,R6}  
2,2,3,3  
2,2,3,3,4  
2,2,3,3,4,4  
2,2,3,3,4,4,5  
LDMIA  
<Rn>,{R1,R2,R3,R4,R5,R6,R7}  
First address not 64-bit aligned  
LDMIA <Rn>,{R1}  
1
2
2
3
3
4
4
2
2
3
3
4
4
5
1
2
2
3
3
4
4
2
2
2
3
3
4
4
5
LDMIA <Rn>,{R1,R2}  
2,3  
LDMIA <Rn>,{R1,R2,R3}  
2,3,3  
LDMIA <Rn>,{R1,R2,R3,R4}  
LDMIA <Rn>,{R1,R2,R3,R4,R5}  
LDMIA <Rn>,{R1,R2,R3,R4,R5,R6}  
2,3,3,4  
2,3,3,4,4  
2,3,3,4,4,5  
2,3,3,4,4,5,5  
LDMIA  
<Rn>,{R1,R2,R3,R4,R5,R6,R7}  
Note  
The Cycle timing behavior that Table 14-17 shows also covers PUSHand POPinstructions that  
behave like store and load multiple instructions with base register write-back.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-21  
         
Cycle Timings and Interlock Behavior  
14.13.2 Load Multiples, where the PC is in the register list  
The processor includes a 4-entry return stack that can predict procedure returns. Any LDMto the  
PC that does not restore the SPSR to the CPSR, is predicted as a procedure return.  
In all cases the base register, <Rn>, is a Very Early Reg.  
Table 14-18 shows the cycle timing behavior of Load Multiples, where the PC is in the register  
list.  
Table 14-18 Cycle timing behavior of Load Multiples, with PC in the register list (64-bit aligned)  
Memory Result  
Example instruction  
Cycles  
Comments  
cycles  
latency  
2,…  
ma  
nb  
nb  
nb  
LDMIA <Rn>,{...,pc}  
LDMIA <Rn>,{...,pc}  
Correct return stack prediction  
Incorrect return stack prediction  
ma + 8  
ma  
2,…  
LDMIA <cond>  
<Rn>,{...,pc}  
2,…  
Correct condition prediction and correct  
return stack prediction  
ma + 7  
ma + 8  
nb  
nb  
LDMIA <cond>  
<Rn>,{...,pc}  
2,…  
2,…  
Incorrect condition prediction  
LDMIA <cond>  
<Rn>,{...,pc}  
Correct condition prediction and incorrect  
return stack prediction  
a. Where m is the number of cycles for this instruction if the PC were treated as a normal register.  
b. Where n is the number of memory cycles for this instruction if the PC were treated as a normal register.  
Note  
The Cycle timing behavior that Table 14-18 shows also covers PUSHand POPinstructions that  
behave like store and load multiple instructions with base register writeback.  
14.13.3 Example Interlocks  
The following sequence that has an LDMinstruction takes six cycles to execute, because R7 has  
a result latency of five cycles:  
LDMIA R0, {R1-R7}  
ADD R10, R10, R7  
The following sequence that has an STMinstruction takes five cycles to execute:  
STMIA R0, {R1-R7}  
ADD R7, R10, R11  
The following sequence has a result latency hidden by issue cycles. It takes five cycles to  
execute.  
LDMIA R0, {R1-R7}  
ADD R10, R10, R3  
The following sequence that has a POPinstruction takes seven cycles to execute, because R9has  
a result latency of six cycles:  
POP {R1-R9}  
ADD R10, R10, R9  
The following sequence that has a PUSHinstruction takes five cycles to execute:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-22  
           
Cycle Timings and Interlock Behavior  
PUSH {R1-R7}  
ADD R10,R10,R7  
Note  
In the examples, R0 and spare 64-bit aligned addresses. The instructions PUSHand POPalways  
use the spregister for the base address.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-23  
Cycle Timings and Interlock Behavior  
14.14 RFE and SRS instructions  
This section describes the cycle timing for the RFEand SRSinstructions.  
These instructions:  
return from an exception and save exception return state respectively  
take one or two memory cycles depending on doubleword alignment first address  
location.  
In all cases the base register is a Very Early Reg.  
Table 14-19 shows the cycle timing behavior for RFEand SRSinstructions.  
Table 14-19 RFE and SRS instructions cycle timing behavior  
Example instruction  
Cycles Memory cycles  
Address doubleword aligned  
RFEIA <Rn>  
10  
1
1
1
SRSIA #<mode>  
Address not doubleword aligned  
RFEIA <Rn>  
11  
2
2
2
SRSIA #<mode>  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-24  
       
Cycle Timings and Interlock Behavior  
14.15 Synchronization instructions  
This section describes the cycle timing behavior for the CLREX  
,
DMB, DSB, ISB, LDREX, LDREXB,  
LDREXD LDREXH, STREX, STREXB, STREXD, STREXH,  
,
SWP, and SWPBinstructions  
In all cases the base register, Rn, is a Very Early Reg. Table 14-20 shows the synchronization  
instructions cycle timing behavior.  
Table 14-20 Synchronization instructions cycle timing behavior  
Instruction  
Cycles Memory cycles  
Result latency  
CLREX  
1
1
1
1
1
1
1
1
1
2
2
-
-
LDREX <Rt>, [Rn]  
LDREXB <Rt>, [Rn]  
LDREXH <Rt>, [Rn]  
LDREXD <Rt>, [Rn]  
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
3
3
a
STREX <Rd>, <Rt>, [Rn]  
STREXB <Rd>, <Rt>, [Rn]  
STREXH <Rd>, <Rt>, [Rn]  
STREXD <Rd>, <Rt>, <Rt2>, [Rn]  
SWP <Rt>, <Rt2>, [Rn]  
a
SWPB <Rt>, <Rt2>, [Rn]  
a. Address must be 64-bit aligned.  
The synchronization instructions DMB DSB, and ISBstall the pipeline for a variable number of  
,
cycles, depending on the current state of the memory system.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-25  
         
Cycle Timings and Interlock Behavior  
14.16 Coprocessor instructions  
This section describes the cycle timing behavior for the MCRand MRCinstructions to CP14, the  
debug coprocessor or CP15, the system control coprocessor.  
The precise timing of coprocessor instructions is tightly linked with the behavior of the relevant  
coprocessor. Table 14-21 shows the coprocessor instructions cycle timing behavior. Table 14-21  
shows the best case numbers.  
Table 14-21 Coprocessor instructions cycle timing behavior  
Instruction Cycles Result latency  
Comments  
MCR  
6
6
4
6
6
4
-
-
MCR <cond>  
-
Condition code passes  
Condition code fails  
-
-
MRC  
6
6
4
MRC <cond>  
Condition code passes  
Condition code fails  
Note  
Some instructions such as cache operations take more cycles.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-26  
       
Cycle Timings and Interlock Behavior  
14.17 SVC, BKPT, Undefined, and Prefetch Aborted instructions  
This section describes the cycle timing behavior for SVC, Undefined instruction, BKPTand  
Prefetch Abort.  
In all cases the exception is taken in the Wr stage of the pipeline. SVCand most Undefined  
instructions that fail their condition codes take one cycle. A small number of Undefined  
instructions that fail their condition codes take two cycles. Table 14-22 shows the SVC BKPT,  
,
Undefined, prefetch aborted instructions cycle timing behavior.  
Table 14-22 SVC, BKPT, Undefined, prefetch aborted instructions cycle timing behavior  
Instruction  
Cycles  
SVC(formerly SWI  
)
9
9
9
9
BKPT  
Prefetch Abort  
Undefined Instruction  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-27  
       
Cycle Timings and Interlock Behavior  
14.18 Miscellaneous instructions  
Table 14-23 shows the cycle timing behavior for If-Then (IT) and No OPeration (NOP)  
instructions.  
Table 14-23 IT and NOP instructions cycle timing behavior  
Example instructions  
Cycles  
Early Reg Late Reg Result latency  
Comments  
IT{<v>{<w>{<z>}}} <cond>  
NOP  
1
1
-
-
-
-
-
-
-
-
The DBG PLI, SEV, WFE, and YIELDinstructions are all treated the same as NOP, and so have the same  
,
cycle timing behavior.  
The WFIinstruction stalls the pipeline for a variable number of cycles, depending on the current  
state of the memory system.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-28  
       
Cycle Timings and Interlock Behavior  
14.19 Floating-point register transfer instructions  
This section describes the cycle timing behavior for the various VFP instruction which transfer  
data between the VFP register file and the integer register file, including the system registers.  
All source operands are Normal Regs, and the result latency for non-system register transfers is  
always 1 cycle.  
Instructions that write data from the integer register file to the VFP system registers (FMXR) are  
blocking, that is, no subsequent instruction can start execution before the FMXRhas completed  
execution. Consequently, the FMXRinstructions take six cycles to execute.  
All transfers to and from the VFP system registers are also serializing. This means that if there  
are any outstanding out-of-order-completion VFP instructions, the system register transfer  
instruction will stall in the iss-stage until these instructions are complete.  
VFP instructions that complete out-of-order are VMLA.F32  
,
VMLS.F32, VNMLS.F32, VNMLA.F32,  
VDIV.F32 VSQRT.F32,  
,
VCVT.F64.F32, and double-precision arithmetic and conversion instructions.  
Table 14-24 shows the floating-point register transfer instructions cycle timing behavior.  
Table 14-24 Floating-point register transfer instructions cycle timing behavior  
Example instruction  
Cycles Result latency Comments  
VMOV <Sn>, <Rt>  
1
1
1
1
1
1
1
1
6
1
1
1
2
1
2
1
2
1
2
-
-
VMOV <Rt>, <Sn>  
-
VMOV <Dn[x]>, <Rt>  
-
VMOV.<dt> <Rt>, <Dn[x]>  
VMOV <Sm>, <Sm1>, <Rt>, <Rt2>  
VMOV <Rt>, <Rt2>, <Sm>, <Sm1>  
VMOV <Dm>, <Rt>, <Rt2>  
VMOV <Rt>, <Rt2>, <Dm>  
VMSR <spec_reg>, <Rt>  
VMRS <Rt>, <spec_reg>  
VMRS APSR_nzcv, FPSCR  
-
-
-
-
-
Blocking and serializing  
Serializing  
2
-
Serializing  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-29  
       
Cycle Timings and Interlock Behavior  
14.20 Floating-point load/store instructions  
This section describes the cycle timing behavior for all load and store instructions that operate  
on the VFP register file:  
The base address register, and any offset register are Very Early Regs for both loads and  
stores.  
For store instructions, the data register (Sd or Dd), or registers are always Late Regs.  
The cycle timing of load and store instructions is affected by the starting address for the  
transfer.  
Note  
The starting address is not always the same as the base address.  
The cycle timing of load and store multiple instructions is also affected by whether or not  
the base address register is updated by the instruction, that is, base register writeback.  
Table 14-25 shows the number of cycles and result latencies for single load and store  
instructions and load multiple instructions. Values are shown for each instruction with and  
without base register writeback, and with different starting address alignments. Cycle counts  
and base register result latencies for store multiple instructions are the same as for the equivalent  
load multiple instruction.  
Table 14-25 Floating-point load/store instructions cycle timing behavior  
Result  
Cycles/  
memory  
cycles  
Result  
latency  
(load)  
latency  
(base  
register,  
<Rn>)  
Cycles with  
writeback (!)  
Example instruction  
Comments  
VLDR.32 <Sd>, [<Rn>{, #+/-<imm>}]  
VLDR.64 <Dd>, [<Rn>{, #+/-<imm>}]  
VLDR.64 <Dd>, [<Rn>{, #+/-<imm>}]  
VSTR.32 <Sd>, [<Rn>{, #+/-<imm>}]  
VSTR.64 <Dd>, [<Rn>{, #+/-<imm>}]  
VSTR.64 <Dd>, [<Rn>{, #+/-<imm>}]  
First address 64-bit aligned  
1
1
2
1
1
2
-
-
-
-
-
-
1
1
2
-
-
-
-
-
-
-
-
64-bit aligned address  
Not aligned  
-
-
64-bit aligned address  
Not aligned  
-
VLDM{mode}.32 <Rn>{!}, {s1}  
1
1
2
2
1
2
3
4
1
2
2
3
2
3
4
5
1
1
2
2
3
2
3
4
5
-
-
-
-
-
-
-
-
VLDM{mode}.32 <Rn>{!}, {s1,s2}  
VLDM{mode}.32 <Rn>{!}, {s1-s3}  
VLDM{mode}.32 <Rn>{!}, {s1-s4}  
VLDM{mode}.64 <Rn>{!}, {d1}  
1,1  
1,1,2  
1,1,2,2  
1
VLDM{mode}.64 <Rn>{!}, {d1,d2}  
VLDM{mode}.64 <Rn>{!}, {d1-d3}  
VLDM{mode}.64 <Rn>{!}, {d1-d4}  
1,2  
1,2,3  
1,2,3,4  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-30  
       
Cycle Timings and Interlock Behavior  
Table 14-25 Floating-point load/store instructions cycle timing behavior (continued)  
Result  
Cycles/  
memory  
cycles  
Result  
latency  
(load)  
latency  
(base  
register,  
<Rn>)  
Cycles with  
writeback (!)  
Example instruction  
Comments  
First address not 64-bit aligned  
VLDM{mode}.32 <Rn>{!}, {s1}  
VLDM{mode}.32 <Rn>{!}, {s1,s2}  
VLDM{mode}.32 <Rn>{!}, {s1-s3}  
VLDM{mode}.32 <Rn>{!}, {s1-s4}  
VLDM{mode}.64 <Rn>{!}, {d1}  
VLDM{mode}.64 <Rn>{!}, {d1,d2}  
VLDM{mode}.64 <Rn>{!}, {d1-d3}  
VLDM{mode}.64 <Rn>{!}, {d1-d4}  
1
2
2
3
2
3
4
5
1
2
3
3
2
3
4
5
1
1
2
3
3
2
3
4
5
-
-
-
-
-
-
-
-
1,2  
1,2,2  
1,2,2,3  
2
2,3  
2,3,4  
2,3,4,5  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-31  
Cycle Timings and Interlock Behavior  
14.21 Floating-point single-precision data processing instructions  
This section describes the cycle timing behavior for all single-precision VFP CDPinstructions.  
This includes arithmetic instructions such as VMUL.F32, data and immediate moving instructions  
such as “VMOV.F32 <Sd>, #<imm>” VABS.F32, VNEG.F32, and “VMOV <Sd>, <Sm>”, and comparison  
,
instructions and conversion instructions.  
Table 14-26 shows the floating-point single-precision data processing instructions cycle timing  
behavior.  
Table 14-26 Floating-point single-precision data processing instructions cycle timing  
behavior  
Example instruction  
Cycles  
Early Reg  
Result latency  
a
1b  
1
2
2
1
1
1
1
1
1
1
1
3
5c  
2
<Sn>  
<Sn>  
<Sn>  
<Sm>  
-
,
,
,
<Sm>  
<Sm>  
<Sm>  
VMLA.F32 <Sd>, <Sn>, <Sm>  
VADD.F32 <Sd>, <Sn>, <Sm>  
VDIV.F32 <Sd>, <Sn>, <Sm>  
VSQRT.F32 <Sd>, <Sm>  
d
16  
16  
1
VMOV.F32 <Sd>, #<imm>  
e
-
1
VMOV.F32 <Sd>, <Sm>  
f
<Sd>  
<Sd>  
<Sm>  
<Sd>  
<Sm>  
<Sd>  
<Sm>  
,
<Sm>  
-
VCMP.F32 <Sd>, <Sm>  
f
-
VCMPE.F32 <Sd>, #0.0  
g
2
VCVT.F32.U32 <Sd>, <Sm>  
h
j
2
VCVT.F32.U32 <Sd>, <Sd>, #<fbits>  
i
2
VCVTR.U32.F32 <Sd>, <Sm>  
2
VCVT.U32.F32 <Sd>, <Sd>, #<fbits>  
VCVT.F64.F32 <Dd>, <Sn>  
5
a. Also VMLS.F32 VNMLS.F32, and VNMLA.F32.  
,
b. VMLA.F32completes out-of-order, and can take an extra cycle (two in total) if an add  
instruction (VADD) or certain dual-issued instruction pairs are in the iss-stage when the  
instruction completes.  
c. Except when the instruction dependent on the result <Sd>is another VMLA.F32  
instruction, and the dependent operand is the accumulate operand, <Sd>. In this case, the  
result latency is reduced to 3 cycles.  
d. Also VSUB.F32  
e. Also VABS.F32and VNEG.F32  
f. Also VCMPE.F32  
,
VMUL.F32, and VNMUL.F32.  
.
.
g. Also VCVT.F32.S32  
h. Also VCVT.F32.U16  
i. Also VCVT.U32.F32  
j. Also VCVT.U16.F32  
.
,
,
,
VCVT.F32.S32, and VCVT.F32.S16  
VCVTR.S32.F32, and VCVT.S32.F32  
VCVT.S32.F32, and VCVT.S16.F32  
.
.
.
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-32  
         
Cycle Timings and Interlock Behavior  
14.22 Floating-point double-precision data processing instructions  
This section describes the cycle timing behavior for all double-precision VFP CDPinstructions.  
This includes arithmetic instructions such as VMUL.F64, data and immediate moving instructions  
such as “VMOV.F64 <Dd>, #<imm>”, VABS.F64 VNEG.F64, and “VMOV <Dd>, <Dm>”, and comparison  
,
instructions and conversion instructions.  
Table 14-27 shows the floating-point double-precision data processing instructions cycle timing  
behavior  
Table 14-27 Floating-point double-precision data processing instructions cycle timing  
behavior  
Example instruction  
Cycles  
Early Reg Result latency  
a
13  
3
3
3
1
1
2
2
3
3
3
3
3
<Dn>  
<Dn>  
<Dn>  
<Dm>  
-
,
,
,
<Dm>  
<Dm>  
<Dm>  
19  
9
VMLA.F64 <Dd>, <Dn>, <Dm>  
VADD.F64 <Dd>, <Dn>, <Dm>  
VDIV.F64 <Dd>, <Dn>, <Dm>  
VSQRT.F64 <Dd>, <Dm>  
b
96  
96  
1
VMOV.F64 <Dd>, #<imm>  
c
-
1
VMOV.F64 <Dd>, <Dm>  
d
<Dd>  
<Dm>  
<Dm>  
<Dd>  
<Dm>  
<Dd>  
<Dm>  
,
<Dm>  
-
VCMP.F64 <Dd>, <Dm>  
d
-
VCMPE.F64 <Dd>, #0.0  
e
7
VCVT.F64.U32 <Dd>, <Sm>  
f
7
VCVT.F64.U32 <Dd>, <Dd>, #<fbits>  
g
7
VCVTR.U32.F64 <Sd>, <Dm>  
h
7
VCVT.U32.F64 <Dd>, <Dd>, #<fbits>  
VCVT.F32.F64 <Sd>, <Dn>  
7
a. Also VMLS.F64  
,
VNMLS.F64, and VNMLA.F64  
.
b. Also VSUB.F64  
,
VMUL.F64, and VNMUL.F64  
.
c. Also VABS.F64and VNEG.F64  
.
d. Also VCMPE.F64  
.
e. Also VCVT.F64.S32  
f. Also VCVT.F64.U16  
g. Also VCVT.U32.F64  
h. Also VCVT.U16.F64  
.
,
,
,
VCVT.F64.S32, and VCVT.F64.S16  
VCVTR.S32.F64, and VCVT.S32.F64  
VCVT.S32.F64, and VCVT.S16.F64  
.
.
.
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-33  
         
Cycle Timings and Interlock Behavior  
14.23 Dual issue  
To increase instruction throughput, the processor can issue certain pairs of instructions  
simultaneously. This is called dual issue. When this happens, the instruction with the smaller  
cycle count is assumed to execute in zero cycles. If a pair of instructions can be dual-issued, they  
are always dual-issued unless dual-issuing is disabled, see Auxiliary Control Registers on  
page 4-38. If one instruction of the pair is interlocked, both are interlocked.  
This section describes:  
14.23.1 Dual issue rules  
The following rules apply to dual-issue instructions:  
Both instructions must be available to the issue stage at the same time. This is unlikely if  
there are many branches.  
The second instruction must not use the PC as a source register unless it is B #immed.  
The first instruction must not use the PC as a destination register.  
Both instructions must belong to the same instruction set, ARM or Thumb.  
There must be no data dependency between the two instructions. That is, the second  
instruction must not have any source registers that are destination registers of the first  
instruction.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-34  
     
Cycle Timings and Interlock Behavior  
14.23.2 Permitted combinations  
Table 14-28 lists the permitted instruction combinations. Any instruction can be conditional or  
flag-setting unless otherwise stated. Only the exact instruction combinations listed in  
Table 14-28 can be dual issued, provided you ensure the instruction combinations obey the rules  
Table 14-28 Permitted instruction combinations  
Dualissue  
case  
First instruction  
Second instruction  
Case A  
Any instruction other than load/store multiple/double,  
flag-setting multiply, non-VFP coprocessor operations,  
miscellaneous processor control instructionsa, or floating  
point instructions if floating point logic is not included in  
the processor  
B #immed  
IT  
NOP  
Case A-Fb  
Case B1  
Any floating point instructions, excluding load/store  
multiple, double precision CDPinstructions, VCVT.F64.F32  
,
and VMRSand VMSR  
.
c
Any data processing instruction that does not  
require a shift by a register value.d  
Any bitfield, saturate or bit-packing  
instruction.e  
LDR <Rt>, [<Rn>, #<imm>]  
c
LDR <Rt>, [<Rn>, <Rm>]  
c
LDR <Rt>, [<Rn>, <Rm>, LSL #1, 2 or 3]  
Any signed or unsigned extend instruction.f  
Any SIMDadd or subtract instruction.g  
Other miscellaneous instructions.h  
Case B1-Fb  
Any single-precision CDPi, excluding  
"VMOV.F32 <Sd>, #<imm>"  
,
VNEG.F32, VABS.F32,  
VCVT.F64.F32 VDIV.F32, and VSQRT.F32  
,
.
32-bit transfers to and from the floating-point  
register filel.  
c
Case B2  
Case B2-Fb  
Case C  
As for Case B1.  
STR <Rt>, [<Rn>, #<imm>]  
As for Case B1-F  
jk  
MOV <Rd>, #immed  
Any data processing instruction.d  
Any bitfield, saturate or bit-packing  
instruction.e  
j
MOVW <Rd>, #immed  
j
MOV <Rd>, <Rm>  
Any signed or unsigned extend instruction.f  
Any SIMDadd or subtract instruction.g  
Other miscellaneous instructions.h  
Case C-Fb  
Case F1b,m  
Case F2_ldb  
32-bit transfers to and from the floating-point  
register filel.  
Any single-precision CDPi, excluding "VMOV.S32 <Sd>,  
As for case C or C-F.  
#<imm>"  
,
VCVT.F64.F32 VABS.F32, and VNEG.F32.  
,
n
As for Case B1 or Case B1-F  
VLDR.F32  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-35  
                               
Cycle Timings and Interlock Behavior  
Table 14-28 Permitted instruction combinations (continued)  
Dualissue  
case  
First instruction  
Second instruction  
n
Case F2_stb  
VSTR.F32  
As for Case B1.  
Any single-precision CDPi, excluding  
multiply-accumulate instructionso.  
32-bit transfers to and from the floating-point  
register filel.  
n
Case F2Db  
Case F3b  
VLDR.F64  
As for Case B1.  
32-bit transfers to and from the floating-point register  
filel  
As for Case F2_st.  
"VMOV.F32 <Sd>, <Sd>, <Sm>" VABS.F32, and VNEG.F32.  
,
Case F4b  
Case F6b  
Any single-precision CDPi, excluding  
Any instruction that does not set flags, other than  
load/store multiple/double, non-VFP coprocessor  
operations, multi-cycle multiply instructionsp, double  
precision floating point CDPinstructions, VCVT.F64.F32, or  
a miscellaneous processor control instructiona  
"VMOV.F32 <Sd>, #<imm>"  
,
VNEG.F32, VABS.F32,  
VCVT.F64.F32 VDIV.F32, and VSQRT.F32.  
,
32-bit transfers to and from the floating-point  
register filel.  
VMRS r15, FPSCR  
As for Case A.  
a. These are processor state updating instructions, synchronization instructions, SVC BKPT, prefetch abort and Undefined  
,
instructions.  
b. This case can only occur if floating-point functionality has been configured for the Cortex-R4F processor, see Configurable  
c. You can substitute LDR with LDRB  
,
LDRH  
,
LDRSB, or LDRSH. You can also substitute STRwith STRBor STRH.  
d. Data processing instructions are ADC  
,
ADD ADDW, AND, ASR, BIC, CLZ, CMN, CMP, EOR, LSL, LSR, MOV, MOVT, MOVW, MVN, ORN, ORR, ROR, RRX,  
,
RSB SBC, SUB, SUBW, TEQ, and TST.  
,
e. Bitfield, saturate, and bit-packing instructions are BFC  
,
BFI  
,
PKHBT  
,
PKHTB  
,
QADD  
,
QDADD  
,
QDSUB  
,
QSUB  
,
SBFX  
,
SSAT  
,
SSAT16  
,
UBFX  
,
USAT  
,
and USAT16  
.
f. Signed or unsigned extend instructions are SXTAB  
,
SXTAB16  
,
SXTAH  
,
SXTB  
,
SXTB16  
,
SXTH  
,
UXTAB  
,
UXTAB16  
,
UXTAH  
,
UXTB  
,
UXTB16, and  
UXTH  
.
g. SIMDadd and subtract instructions are QADD16  
,
QADD8  
UADD16 UADD8  
USUB8, and USAX  
REV REV16  
VNEG.F32 "VMOV.F32 <Sd>, #<imm>"  
VDIV.F32 VSQRT.F32  
VCVTR.U32.F32  
,
QASX  
,
SQUB16  
,
QSUB8  
,
QSAX  
,
SADD16  
,
,
SADD8  
,
SASX  
,
SHADD16  
,
SHADD8  
,
SHASX  
,
SHSUB16  
,
SHSUB8  
,
SHSAX  
,
SSUB16  
,
SSUB8  
,
SSAX  
,
,
,
UASX UHADD16  
,
,
UHADD8  
,
UHASX  
UHSUB16  
,
UHSUB8  
,
UHSAX  
,
UQADD16  
,
UQADD8  
,
UQASX UQSUB16  
,
,
UQSUB8  
,
UQSAX  
,
USUB16  
,
.
h. Other miscellaneous instructions are RBIT  
,
,
,
REVSH, and SEL.  
i. Single-precision CDPsare VABS.F32  
,
,
,
VMLA.F32  
VCVT.F64.F32  
VCVT.S32.F32  
,
VMLS.F32  
VCVT.F32.U32  
VCVT.U16.F32, and VCVT.S16.F32.  
,
VNMLS.F32  
,
VNMLA.F32, VMUL.F32,  
VNMUL.F32  
,
VADD.F32  
,
VSUB.F32  
,
,
,
VCMP.F32  
,
VCMPE.F32  
,
,
,
VCVT.F32.S32  
,
VCVT.F32.U16  
,
VCVT.F32.S16  
,
,
VCVT.U32.F32  
,
VCVTR.S32.F32  
,
,
j. Must not be flag-setting.  
k. Immediate value must not require a shift.  
l. 32-bit transfers to or from the floating point register file include single or half-double floating point register transfers, including  
"VMOV <Sn>, <Rt>" "VMOV <Dn[x]>, <Rt>", "VMOV <Rt>, <Dn[x]>", and "VMOV <Rt>, <Sn>", but excluding VMRSand VMSR.  
,
m. When the first instruction is a floating point multiply-accumulate, and the second instruction is a 32-bit transfer to the  
floating-point register file, case F1 can only occur if the two instructions have different destination registers.  
n. Any addressing modes.  
o. Single-precision floating-point multiply-accumulate instructions are VMLA.F32  
p. Multi-cycle multiply instructions are SMMUL  
,
VMLS.F32  
,
VNMLS.F32, and VNMLA.F32  
.
,
SMMLA  
,
SMMLS  
,
MUL  
,
MLA  
,
MLS  
,
SMULL  
,
SMLAL UMAAL  
,
,
UMULL, and UMLAL  
.
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
14-36  
Chapter 15  
AC Characteristics  
This chapter gives the timing parameters for the processor. It contains the following sections:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
15-1  
   
ACCharacteristics  
15.1 Processor timing  
The AXI bus interface of the processor conforms to the AMBA AXI Specification. For the  
relevant timing of the AXI write and read transfers, and the error response, see the AMBA AXI  
Protocol v1.0 Specification.  
The APB debug interface of the processor conforms to the AMBA 3 APB Protocol v1.0  
Specification. For the relevant timing of the APB write and read transfers, and the error  
response, see the AMBA 3 APB Protocol v1.0 Specification.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
15-2  
   
ACCharacteristics  
15.2 Processor timing parameters  
This section describes the input and output port timing parameters for the processor.  
The maximum timing parameter or constraint delay for each processor signal applied to the SoC  
is given as a percentage in Table 15-1 to Table 15-17 on page 15-11. The input and output delay  
columns provide the maximum and minimum time as a percentage of the processor clock cycle  
given to the SoC for that signal.  
This section describes:  
15.2.1 Input port timing parameters  
Table 15-1 shows the timing parameters for the miscellaneous input ports.  
Table 15-1 Miscellaneous input ports timing parameters:  
Input delay  
minimum  
Input delay  
maximum  
Signal name  
Clock uncertainty 10%  
Clock uncertainty 10%  
Clock uncertainty 10%  
Clock uncertainty 50%  
Clock uncertainty 20%  
nRESET  
nSYSPORESET  
PRESETDBGn  
nCPUHALT  
DBGNOCLKSTOP  
Table 15-2 shows the timing parameters for the configuration input port.  
Table 15-2 Configuration input port timing parameters  
Input delay  
minimum  
Input delay  
maximum  
Signal name  
Clock uncertainty 20%  
Clock uncertainty 20%  
Clock uncertainty 20%  
Clock uncertainty 20%  
Clock uncertainty 20%  
Clock uncertainty 20%  
Clock uncertainty 20%  
Clock uncertainty 20%  
Clock uncertainty 20%  
Clock uncertainty 20%  
Clock uncertainty 20%  
Clock uncertainty 20%  
VINITHI  
CFGEE  
CFGIE  
INITRAMA  
INITRAMB  
LOCZRAMA  
TEINIT  
CFGNMFI  
CFGATCMSZ[3:0]  
CFGBTCMSZ[3:0]  
PARECCENRAM[2:0]  
ERRENRAM[2:0]  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
15-3  
             
ACCharacteristics  
Table 15-2 Configuration input port timing parameters (continued)  
Input delay  
minimum  
Input delay  
maximum  
Signal name  
Clock uncertainty 20%  
Clock uncertainty 20%  
Clock uncertainty 20%  
Clock uncertainty 20%  
PARLVRAM  
ENTCM1IF  
SLBTCMSB  
RMWENRAM[1:0]  
Table 15-3 shows the timing parameters for the interrupt input ports.  
Table 15-3 Interrupt input ports timing parameters  
Input delay  
minimum  
Input delay  
maximum  
Signal name  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 10%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
nFIQ  
nIRQ  
INTSYNCEN  
IRQADDRV  
IRQADDRVSYNCEN  
IRQADDR[31:2]  
Table 15-4 shows the input timing parameters for the AXI master port.  
Table 15-4 AXI master input port timing parameters  
Input  
delay  
maximum  
Input delay  
minimum  
Signal name  
Clock uncertainty  
Clock uncertainty  
Clock uncertainty  
Clock uncertainty  
Clock uncertainty  
Clock uncertainty  
Clock uncertainty  
Clock uncertainty  
Clock uncertainty  
Clock uncertainty  
Clock uncertainty  
50%  
60%  
60%  
60%  
60%  
60%  
60%  
60%  
60%  
60%  
60%  
ACLKENM  
AWREADYM  
WREADYM  
BIDM[3:0]  
BRESPM[1:0]  
BVALIDM  
ARREADYM  
RIDM[3:0]  
RDATAM[63:0]  
RRESPM[1:0]  
RLASTM  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
15-4  
       
ACCharacteristics  
Table 15-4 AXI master input port timing parameters (continued)  
Input  
delay  
maximum  
Input delay  
minimum  
Signal name  
Clock uncertainty  
Clock uncertainty  
Clock uncertainty  
60%  
60%  
60%  
RVALIDM  
BPARITYM  
RPARITYM  
Table 15-5 shows the input timing parameters for the AXI slave port.  
Table 15-5 AXI slave input port timing parameters  
Input  
delay  
maximum  
Input delay  
minimum  
Signal name  
Clock uncertainty 50%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
ACLKENS  
AWIDS[7:0]  
AWADDRS[22:0]  
AWLENS[3:0]  
AWSIZES[2:0]  
AWBURSTS[1:0]  
AWPROTS  
AWUSERS[3:0]  
AWVALIDS  
Clock uncertainty  
Clock uncertainty  
Clock uncertainty  
Clock uncertainty  
Clock uncertainty  
60%  
60%  
60%  
60%  
60%  
WDATAS[63:0]  
WSTRBS[7:0]  
WLASTS  
WVALIDS  
BREADYS  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
ARIDS[7:0]  
ARADDRS[22:0]  
ARLENS[3:0]  
ARSIZES[2:0]  
ARBURSTS[1:0]  
ARPROTS  
ARUSERS[3:0]  
ARVALIDS  
Clock uncertainty  
Clock uncertainty  
60%  
60%  
RREADYS  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
15-5  
   
ACCharacteristics  
Table 15-5 AXI slave input port timing parameters (continued)  
Input  
delay  
maximum  
Input delay  
minimum  
Signal name  
Clock uncertainty 60%  
AWPARITYS  
WPARITYS  
ARPARITYS  
Clock uncertainty  
Clock uncertainty  
60%  
60%  
Table 15-6 shows the input timing parameters for the debug input ports.  
Table 15-6 Debug input ports timing parameters  
Input delay  
minimum  
Input delay  
maximum  
Signal name  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 10%  
Clock uncertainty 10%  
Clock uncertainty 10%  
Clock uncertainty 10%  
Clock uncertainty 50%  
DBGEN  
NIDEN  
EDBGRQ  
PCLKENDBG  
PSELDBG  
PADDRDBG[11:2]  
PADDRDBG31  
PWDATADBG[31:0]  
PENABLEDBG  
PWRITEDBG  
DBGROMADDR[31:12]  
DBGROMADDRV  
DBGSELFADDR[31:12]  
DBGSELFADDRV  
DBGRESTART  
Table 15-7 shows the input timing parameters for the ETM input ports.  
Table 15-7 ETM input ports timing parameters  
Input delay  
minimum  
Inputdelay  
maximum  
Signal name  
Clock uncertainty  
Clock uncertainty  
Clock uncertainty  
50%  
50%  
50%  
ETMPWRUP  
nETMWFIREADY  
ETMEXTOUT[1:0]  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
15-6  
       
ACCharacteristics  
Table 15-8 shows the timing parameters for the test input ports.  
Table 15-8 Test input ports timing parameters  
Input  
delay  
maximum  
Input delay  
minimum  
Signal name  
Clock uncertainty 10%  
Clock uncertainty 10%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
SE  
RSTBYPASS  
MBTESTON  
MBISTDIN[71:0]  
MBISTADDR[19:0]  
MBISTCE  
MBISTSEL[4:0]  
MBISTWE[7:0]  
Table 15-9 shows the timing parameters for the TCM interface input ports.  
Table 15-9 TCM interface input ports timing parameters  
Input  
delay  
maximum  
Input delay  
minimum  
Signal name  
Clock uncertainty 65%  
Clock uncertainty 65%  
Clock uncertainty 65%  
Clock uncertainty 50%  
Clock uncertainty 40%  
Clock uncertainty 50%  
Clock uncertainty 65%  
Clock uncertainty 65%  
Clock uncertainty 65%  
Clock uncertainty 50%  
Clock uncertainty 40%  
Clock uncertainty 50%  
Clock uncertainty 65%  
Clock uncertainty 65%  
Clock uncertainty 65%  
ATCDATAIN[63:0]  
ATCPARITYIN[13:0]  
ATCERROR  
ATCWAIT  
ATCLATEERROR  
ATCRETRY  
B0TCDATAIN[63:0]  
B0TCPARITYIN[13:0]  
B0TCERROR  
B0TCWAIT  
B0TCLATEERROR  
B0TCRETRY  
B1TCDATAIN[63:0]  
B1TCPARITYIN[13:0]  
B1TCERROR  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
15-7  
       
ACCharacteristics  
Table 15-9 TCM interface input ports timing parameters (continued)  
Input  
delay  
maximum  
Input delay  
minimum  
Signal name  
Clock uncertainty 50%  
Clock uncertainty 40%  
Clock uncertainty 50%  
B1TCWAIT  
B1TCLATEERROR  
B1TCRETRY  
The timing parameters for the dual-redundant core compare logic input control buses,  
DCCMINP[7:0] and DCCMINP2[7:0], are implementation-defined. Contact the implementer  
of the macrocell you are working with.  
15.2.2 Output ports timing parameters  
Most output ports have a maximum output delay of 60%, that is the SoC is enabled to use 60%  
of the clock cycle.  
Table 15-10 shows the timing parameter for the miscellaneous output port.  
Table 15-10 Miscellaneous output port timing parameter  
Output delay  
minimum  
Output delay  
maximum  
Signal name  
Clock uncertainty 10%  
STANDBYWFI  
Table 15-11 shows the timing parameters for the interrupt output ports.  
Table 15-11 Interrupt output ports timing parameters  
Output delay  
minimum  
Output delay  
maximum  
Signal name  
Clock uncertainty 60%  
Clock uncertainty 60%  
IRQACK  
nPMUIRQ  
Table 15-12 shows the timing parameters for the AXI master output port.  
Table 15-12 AXI master output port timing parameters  
Output delay  
minimum  
Output delay  
maximum  
Signal name  
Clock uncertainty  
Clock uncertainty  
Clock uncertainty  
Clock uncertainty  
Clock uncertainty  
Clock uncertainty  
Clock uncertainty  
60%  
60%  
60%  
60%  
60%  
60%  
60%  
AWIDM[3:0]  
AWADDRM[31:0]  
AWLENM[3:0]  
AWSIZEM[2:0]  
AWBURSTM[1:0]  
AWLOCKM[1:0]  
AWCACHEM[3:0]  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
15-8  
             
ACCharacteristics  
Table 15-12 AXI master output port timing parameters (continued)  
Output delay  
minimum  
Output delay  
maximum  
Signal name  
Clock uncertainty  
Clock uncertainty  
Clock uncertainty  
Clock uncertainty  
Clock uncertainty  
Clock uncertainty  
Clock uncertainty  
Clock uncertainty  
Write response channel  
60%  
60%  
60%  
60%  
60%  
60%  
60%  
60%  
AWPROTM[2:0]  
AWUSERM[4:0]  
AWVALIDM  
WIDM[3:0]  
WDATAM[63:0]  
WSTRBM[7:0]  
WLASTM  
WVALIDM  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 50%  
BREADYM  
ARIDM[3:0]  
ARADDRM[31:0]  
ARLENM[3:0]  
ARSIZEM[2:0]  
ARBURSTM[1:0]  
ARLOCKM[1:0]  
ARCACHEM[3:0]  
ARPROTM[2:0]  
ARUSERM[4:0]  
ARVALIDM  
RREADYM  
AWPARITYM  
WPARITYM  
ARPARITYM  
AXIMPARERR[1:0]  
Table 15-13 shows the timing parameters for the AXI slave output ports.  
Table 15-13 AXI slave output ports timing parameters  
Output delay  
minimum  
Output delay  
maximum  
Signal name  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
AWREADYS  
WREADYS  
BIDS[7:0]  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
15-9  
   
ACCharacteristics  
Table 15-13 AXI slave output ports timing parameters (continued)  
Output delay  
minimum  
Output delay  
maximum  
Signal name  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 50%  
BRESPS[1:0]  
BVALIDS  
ARREADYS  
RIDS[7:0]  
RDATAS[63:0]  
RRESPS[1:0]  
RLASTS  
RVALIDS  
BPARITYS  
RPARITYS  
AXISPARERR[2:0]  
Table 15-14 shows the timing parameters for the debug interface output ports.  
Table 15-14 Debug interface output ports timing parameters  
Output delay  
minimum  
Output delay  
maximum  
Signal name  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
PRDATADBG[31:0]  
PREADYDBG  
PSLVERRDBG  
DBGNOPWRDWN  
DBGACK  
DBGTRIGGER  
DBGRESTARTED  
DBGRSTREQ  
COMMTX  
COMMRX  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
15-10  
   
ACCharacteristics  
Table 15-15 shows the timing parameters for the ETM interface output ports.  
Table 15-15 ETM interface output ports timing parameters  
Output delay  
minimum  
Outputdelay  
maximum  
Signal name  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
ETMICTL[13:0]  
ETMIA[31:1]  
ETMDCTL[11:0]  
ETMDA[31:0]  
ETMDD[63:0]  
ETMCID[31:0]  
ETMWFIPENDING  
EVNTBUS[46:0]  
Table 15-16 shows the timing parameters for the test output ports.  
Table 15-16 Test output ports timing parameters  
Output delay  
minimum  
Output delay  
maximum  
Signal name  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
Clock uncertainty 50%  
MBISTDOUT[71:0]  
nVALIRQ  
nVALFIQ  
nVALRESET  
VALEDBGRQ  
Table 15-17 shows the timing parameters for the TCM interface output ports.  
Table 15-17 TCM interface output ports timing parameters  
Output delay  
minimum  
Output delay  
maximum  
Signal name  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
ATCEN0  
ATCEN1  
ATCADDR[22:3]  
ATCBYTEWR[7:0]  
ATCSEQ  
ATCDATAOUT[63:0]  
ATCPARITYOUT[13:0]  
ATCACCTYPE[2:0]  
ATCWE  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
15-11  
           
ACCharacteristics  
Table 15-17 TCM interface output ports timing parameters (continued)  
Output delay  
minimum  
Output delay  
maximum  
Signal name  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
Clock uncertainty 45%  
ATCADDRPTY  
B0TCEN0  
B0TCEN1  
B0TCADDR[22:3]  
B0TCBYTEWR[7:0]  
B0TCSEQ  
B0TCDATAOUT[63:0]  
B0TCPARITYOUT[13:0]  
B0TCACCTYPE[2:0]  
B0TCWE  
B0TCADDRPTY  
B1TCEN0  
B1TCEN1  
B1TCADDR[23:0]  
B1TCBYTEWR[7:0]  
B1TCSEQ  
B1TCDATAOUT[63:0]  
B1TCPARITYOUT[13:0]  
B1TCACCTYPE[2:0]  
B1TCWE  
B1TCADDRPTY  
Table 15-18 shows the timing parameters for the FPU output signals.  
Table 15-18 FPU output port timing parameters  
Output delay  
minimum  
Output delay  
maximum  
Signal name  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
Clock uncertainty 60%  
FPIXC  
FPOFC  
FPUFC  
FPIOC  
FPDZC  
FPIDC  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
15-12  
   
ACCharacteristics  
The timing parameters for the dual-redundant core compare logic output buses,  
DCCMOUT[7:0] and DCCMOUT2[7:0], are implementation-defined. Contact the  
implementer of the macrocell you are working with.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
15-13  
Appendix A  
Processor Signal Descriptions  
This appendix describes the processor signals. It contains the following sections:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
A-1  
   
Processor Signal Descriptions  
A.1  
About the processor signal descriptions  
The tables in this appendix list the processor signals, along with their dimensions and direction,  
input or output, and a high-level description. Each table also has a clocking column, that  
indicates by which clock a signal is sampled or driven. All signals are sampled on or driven from  
the rising edge of the clock. The clocking column can also contain the following information:  
Any  
Means the input is synchronised inside the processor, so the input can be driven  
from any clock.  
Tie-off  
Reset  
Means the input must be tied to a fixed value.  
Means the input must only be changed under reset.  
Clocking is listed for all outputs, though some are typically synchronized into a different clock  
before use.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
A-2  
   
Processor Signal Descriptions  
A.2  
Global signals  
Table A-1 shows the processor global signals.  
The free clock is ungated, with minimal insertion delay, because it clocks the clock gating  
circuits. Therefore, you must ensure that incoming clocks are balanced with the free clock.  
Table A-1 Global signals  
Signal  
Direction Clocking  
Description  
FREECLKIN  
CLKIN  
Input  
Input  
Input  
-
-
-
Free version of the core clock.  
Core clock.  
CLKIN2  
Core clock, in phase with DUALCKLIN, for configurations  
with dual-redundant core.a  
nRESET  
Input  
Input  
Input  
Any  
Core reset.  
nSYSPORESET  
nCPUHALT  
Any  
System power on reset.  
Any  
Processor halt after reset.  
Processor does not stop the clocks when entering WFI state.a  
Clock for second, redundant, core.a  
Clock for second, redundant, core, in phase with CLKIN.a  
DBGNOCLKSTOP Input  
Any  
DUALCLKIN  
DUALCLKIN2  
STANDBYWFI  
Input  
-
Input  
-
Output  
FREECLKIN  
Indicates that the processor is in Standby mode and the  
processor clock is stopped. You can use this signal for TCMs  
RAM clock gating.  
a. Not available in r0px revisions of the processor.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
A-3  
         
Processor Signal Descriptions  
A.3  
Configuration signals  
Table A-2 shows the processor configuration signals.  
Table A-2 Configuration signals  
Signal  
Direction Clocking Description  
VINITHI  
Input  
Input  
Input  
Input  
Input  
Input  
Tie-off,  
Reset  
Reset V-bit value. When HIGH indicates HIVECS mode at reset.  
information.  
CFGEE  
Tie-off,  
Reset  
Reset EE-bit value. When HIGH indicates the implementation  
uses BE-8 mode for exceptions at reset. See c1, System Control  
CFGIE  
Tie-off,  
Reset  
Instruction side endianness, reflected in the IE-bit. When HIGH  
indicates that big endian instruction fetch is used. See c1, System  
INITRAMA  
INITRAMB  
LOCZRAMA  
Tie-off,  
Reset  
Reset value of ATCM enable bit. When HIGH indicates  
Tightly-Coupled Memory A, ATCM, enabled at reset. See c9,  
Tie-off,  
Reset  
Reset value of BTCM bit. When HIGH indicates  
Tightly-Coupled Memory B, BTCM, enabled at reset. See c9,  
Tie-off,  
Reset  
When HIGH indicates ATCM initial base address is zero and  
BTCM base address is implementation-defined.  
When LOW indicates BTCM initial base address is zero and  
ATCM base address is implementation-defined.  
TEINIT  
Input  
Input  
Tie-off,  
Reset  
Reset TE-bit value. Determines exception handling state at reset.  
When set to:  
0 = ARM  
1 = Thumb.  
information.  
CFGATCMSZ[3:0]  
Tie-off  
Selects the ATCM size. The encodings for the TCM sizes are:  
b0000 = 0KB  
b0011 = 4KB  
b0100 = 8KB  
b0101 = 16KB  
b0110 = 32KB  
b0111 = 64KB  
b1000 = 128KB  
b1001 = 256KB  
b1010 = 512KB  
b1011 = 1MB  
b1100 = 2MB  
b1101 = 4MB  
b1110 = 8MB.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
A-4  
       
Processor Signal Descriptions  
Table A-2 Configuration signals (continued)  
Signal  
Direction Clocking Description  
CFGBTCMSZ[3:0]  
Input  
Tie-off  
Selects the BTCM size. The encodings for the TCM sizes are:  
b0000 = 0KB  
b0011 = 4KB  
b0100 = 8KB  
b0101 = 16KB  
b0110 = 32KB  
b0111 = 64KB  
b1000 = 128KB  
b1001 = 256KB  
b1010 = 512KB  
b1011 = 1MB  
b1100 = 2MB  
b1101 = 4MB  
b1110 = 8MB.  
CFGNMFI  
ENTCM1IF  
Input  
Input  
Tie-off,  
Reset  
When HIGH, enable non-maskable Fast Interrupts. Reflected in  
more information.  
Tie-off  
Enable B1TCM interface.  
Use B0TCM only if this signal not tied HIGH.  
PARECCENRAM[2:0] Input  
Tie-off,  
Reset  
TCMs parity or ECC check enable. Tie each bit HIGH to enable  
parity or ECC checking on the appropriate TCM at reset. Use  
following values:  
2:B1TCMa  
1: B0TCMa  
0: ATCM  
information.  
PARLVRAM  
Input  
Tie-off,  
Reset  
Selects between odd and even parity for caches, TCMs, and  
Tie LOW for even parity  
Tie HIGH for odd parity.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
A-5  
Processor Signal Descriptions  
Table A-2 Configuration signals (continued)  
Signal  
Direction Clocking Description  
ERRENRAM[2:0]  
Input  
Tie-off,  
Reset  
TCMs external error enable. Tie each bit high to enable the  
external error signals for each TCM at reset. Use the following  
values:  
2: B1TCM  
1: B0TCM  
0: ATCM  
information.  
RMWENRAM[1:0]b  
Input  
Tie-off,  
Reset  
RMW enable bits reset values. Tie each bit high to enable  
read-modify-write for TCM interfaces at reset.c Use the  
following values:  
1: BTCM  
0: ATCM  
information.  
SLBTCMSB  
Input  
Tie-off  
Use most significant bit of BTCM address to select B1TCM if  
this signal is HIGH.  
Use bit [3] of the BTCM address if this signal is LOW.  
a. If the BTCM is configured with ECC, bit[2] and bit[1] must be the same value.  
b. Not used if 32-bit ECC is included.  
c. Not available in r0px revisions of the processor.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
A-6  
Processor Signal Descriptions  
A.4  
Interrupt signals, including VIC interface signals  
Table A-3 shows the Interrupt signals including signals used on the VIC interface.  
Table A-3 Interrupt signals  
Signal  
Direction Clocking Description  
CLKINa  
Anyb  
Fast interruptc.  
nFIQ  
Input  
Input  
Input  
Input  
Input  
CLKINa  
Anyb  
Normal interruptc.  
nIRQ  
INTSYNCEN  
IRQADDRV  
IRQADDRVSYNCEN  
Tie-off  
Tie HIGH if the interrupt inputs are asynchronous to CLKIN.  
Tie LOW if the interrupt inputs are synchronous to CLKIN.  
CLKINd  
Anye  
Indicates IRQADDR is valid.  
Tie-off  
Tie HIGH if the IRQADDRV input from the VIC is  
asynchronous to CLKIN.  
Tie HIGH if the IRQADDRV input from the VIC is  
synchronous to CLKIN.  
IRQADDR [31:2]  
Input  
-
Address of the IRQ. This signal must be stable when  
IRQADDRV is asserted.  
IRQACK  
Output  
Output  
CLKIN  
CLKIN  
Acknowledges interrupt.  
nPMUIRQ  
Interrupt request by Performance Monitor Unit (PMU).  
a. When INTSYNCEN is tied LOW  
b. When INTSYNCEN is tied HIGH  
c. This signal is level-sensitive and must be held LOW until a suitable interrupt response is received from the processor.  
d. When IRQADDRVSYNCEN is tied LOW  
e. When IRQADDRVSYCNEN is tied HIGH  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
A-7  
           
Processor Signal Descriptions  
A.5  
L2 interface signals  
This section describes the processor L2 interface AXI signals. For more information on  
Advanced Microcontroller Bus Architecture (AMBA) AXI signals see the AMBA AXI Protocol  
Specification.  
Note  
All the outputs listed in this section have their reset values during standby.  
A.5.1  
AXI master port  
Table A-4 shows the AXI master port signals for the L2 interface. With the exception of the  
ACLKENM, all signals are only sampled or driven on CLKIN edges when ACLKENM is  
asserted, see AXI interface clocking on page 3-9 for more information.  
Table A-4 AXI master port signals for the L2 interface  
Signal  
Direction Clocking  
Description  
ACLKENM  
Input  
CLKIN  
Clock enable for the AXI master port.  
Write address channel  
AWADDRM[31:0]  
AWBURSTM[1:0]  
AWCACHEM[3:0]  
Output  
Output  
Output  
CLKIN  
CLKIN  
CLKIN  
Transfer start address.  
Write burst type.  
Provides decode information for outer attributes:  
b0000 = Strongly Ordered.  
b0001 = Device.  
b0011 = Normal, Non-cacheable.  
b0110 = Normal, Cacheable. write-through.  
b1111 = Normal, Cacheable. write-back, write allocation.  
b0111 = Normal, Cacheable. write-back, no write allocation.  
Note  
The AXI specification describes these encodings using the  
pre-ARMv6 terms such as cacheable-bufferable. These terms  
are equivalent to the ARMv6 memory-type descriptions such as  
Normal, Non-cacheable used here.  
AWIDM[3:0]  
Output  
Output  
CLKIN  
CLKIN  
The identification tag for the write address group of signals.  
AWLENM [3:0]  
Write transfer burst length. The transfer burst length range is  
from one to 16. A 4-bit binary value minus one determines the  
transfer burst length.  
AWLOCKM[1:0]  
AWPROTM[2:0]  
AWREADYM  
Output  
Output  
Input  
CLKIN  
CLKIN  
CLKIN  
Lock signal.  
Protection type. Only bit [0] is used from the 3-bit AXI bus.  
Address ready. The slave uses this signal to indicate that it can  
accept the address.  
AWSIZEM[2:0]  
AWUSERM[4:0]  
Output  
Output  
CLKIN  
CLKIN  
Indicates the size of the transfer.  
Provides decode information for the write address channel. See  
Table 9-3 on page 9-5 for information about the encoding of this  
signal.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
A-8  
       
Processor Signal Descriptions  
Table A-4 AXI master port signals for the L2 interface (continued)  
Signal  
AWVALIDM  
Direction Clocking  
Description  
Output  
CLKIN  
Indicates address and control are valid.  
Write data channel  
WDATAM[63:0]  
WIDM[3:0]  
Output  
Output  
Output  
Input  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
Write data.  
The identification tag for the write data group of signals.  
Indicates the last data transfer of a burst.  
Indicates that the slave is ready to accept write data  
Write strobes used to indicate which byte lanes must be updated.  
Indicates address and control are valid.  
WLASTM  
WREADYM  
WSTRBM[7:0]  
WVALIDM  
Output  
Output  
Write response channel  
BIDM [3:0]  
Input  
Output  
Input  
Input  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
The identification tag for the write response signal.  
Indicates that the core is ready to accept write response.  
Write response.  
BREADYM  
BRESPM[1:0]  
BVALIDM  
Indicates that a valid write response is available.  
Read address channel  
ARADDRM[31:0]  
ARBURSTM[1:0]  
ARCACHEM[3:0]  
Output  
Output  
Output  
CLKIN  
CLKIN  
CLKIN  
Instruction fetch burst start address.  
Burst type.  
Provides decode information for outer attributes:  
b0000 = Strongly Ordered.  
b0001 = Device.  
b0011 = Normal, Non-cacheable.  
b0110 = Normal, Cacheable. write-through.  
b1111 = Normal, Cacheable. write-back, write allocation.  
b0111 = Normal, Cacheable. write-back, no write allocation.  
Note  
The AXI specification describes these encodings using the  
pre-ARMv6 terms such as cacheable-bufferable. These terms  
are equivalent to the ARMv6 memory-type descriptions such as  
Normal, Non-cacheable used here.  
ARIDM[3:0]  
Output  
Output  
Output  
Output  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
Identification tag for the read address group of signals  
Instruction fetch burst length.  
Lock signal.  
ARLENM [3:0]  
ARLOCKM[1:0]  
ARPROTM[2:0]  
Protection signals provide addition information about a bus  
access.  
ARREADYM  
Input  
CLKIN  
CLKIN  
Address ready. The slave uses this signal to indicate that it can  
accept the address.  
ARSIZEM[2:0]  
Output  
Indicates the size of the transfer.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
A-9  
Processor Signal Descriptions  
Table A-4 AXI master port signals for the L2 interface (continued)  
Signal  
ARUSERM[4:0]  
Direction Clocking  
Description  
Output  
CLKIN  
Provides decode information for the read address channel. See  
Table 9-3 on page 9-5 for information about the encoding of this  
signal.  
ARVALIDM  
Read Data Channel  
RDATAM[63:0]  
RIDM[3:0]  
Output  
CLKIN  
Indicates address and control are valid.  
Input  
Input  
Input  
Output  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
Read Data.  
The identification tag for the read data group of signals.  
Indicates the last transfer in a read burst.  
RLASTM  
RREADYM  
Read ready signal indicating that the bus master can accept read  
data and response information.  
RRESPM[1:0]  
RVALIDM  
Input  
Input  
CLKIN  
CLKIN  
Read response.  
Indicates that read data is available.  
A.5.2  
AXI master port error detection signals  
Table A-5 shows the AXI master port error detection signals. these signals are only generated if  
the processor is configured to include AXI bus parity. See Configurable options on page 1-13  
for more information.  
Table A-5 AXI master port error detection signals  
Direction Clocking Description  
Signal  
AWPARITYM  
WPARITYM  
BPARITYM  
ARPARITYM  
RPARITYM  
Output  
Output  
Input  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
Parity bit for write address channel  
Parity bit for write data channel  
Parity bit for write response channel  
Parity bit for read address channel  
Parity bit for read data channel  
Output  
Input  
AXIMPARERR[1:0] Output  
Parity error indication for read data (bit [1]) and write response  
(bit[0]) channels  
A.5.3  
AXI slave port  
Table A-6 shows the AXI slave port signals for the L2 interface. With the exception of the  
ACLKENS, all signals are only sampled or driven on CLKIN edges when ACLKENS is  
asserted, see AXI interface clocking on page 3-9 for more information.  
Table A-6 AXI slave port signals for the L2 interface  
Signal  
Direction Clocking  
Description  
ACLKENS  
Input  
CLKIN  
Clock enable for the AXI slave port.  
Write Address Channel  
AWADDRS[22:0] Input  
CLKIN  
Transfer start address.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
A-10  
       
Processor Signal Descriptions  
Table A-6 AXI slave port signals for the L2 interface (continued)  
Signal  
Direction Clocking  
Description  
AWBURSTS[1:0] Input  
CLKIN  
CLKIN  
CLKIN  
Write burst type.  
AWIDS[7:0]  
Input  
Input  
The identification tag for the write address group of signals.  
AWLENS[3:0]  
Write transfer burst length. The transfer burst length range is from  
one to 16. A four bit binary value minus one determines the  
transfer burst length.  
AWPROTS  
Input  
CLKIN  
CLKIN  
Protection information, privileged/normal access. AWPROT[0] in  
AXI specification.  
AWREADYS  
Output  
Address ready. The slave uses this signal to indicate that it can  
accept the address.  
AWSIZES[2:0]  
AWUSERS[3:0]  
Input  
Input  
CLKIN  
CLKIN  
Indicates the size of the transfer.  
Memory type select data cache, instruction cache, BTCM or  
ATCM, one hot. AWUSERS[3:0] signal is not part of the standard  
AXI specification.  
AWVALIDS  
Write Data Channel  
WDATAS[63:0]  
WLASTS  
Input  
CLKIN  
Indicates address and control are valid.  
Input  
Input  
Output  
Input  
Input  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
Write data.  
Indicates the last data transfer of a burst.  
Indicates that the slave is ready to accept write data.  
Write strobes used to indicate which byte lanes must be updated.  
Indicates address and control are valid.  
WREADYS  
WSTRBS[7:0]  
WVALIDS  
Write Response Channel  
BIDS[7:0]  
Output  
Input  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
The identification tag for the write response signal.  
Indicates that the core is ready to accept write response.  
Write response.  
BREADYS  
BRESPS[1:0]  
BVALIDS  
Output  
Output  
Indicates that a valid write response is available.  
Read Address Channel  
ARADDRS[22:0]  
ARBURSTS[1:0]  
ARIDS[7:0]  
Input  
Input  
Input  
Input  
Input  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
Instruction fetch burst start address.  
Burst type.  
Identification tag for the read address group of signals.  
Instruction fetch burst length.  
ARLENS[3:0]  
ARPROTS  
Protection information, privileged/normal access. ARPROT[0] in  
AXI specification.  
ARREADYS  
Output  
Input  
CLKIN  
CLKIN  
Address ready. The slave uses this signal to indicate that it can  
accept the address.  
ARSIZES[2:0]  
Indicates the size of the transfer.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
A-11  
Processor Signal Descriptions  
Table A-6 AXI slave port signals for the L2 interface (continued)  
Signal  
ARUSERS[3:0]  
Direction Clocking  
Description  
Input  
CLKIN  
Memory type select {data cache, instruction cache, BTCM or  
ATCM}, one hot. AWUSERS[3:0] signal is not part of the  
standard AXI specification.  
ARVALIDS  
Read Data Channel  
RDATAS[63:0]  
RIDS[7:0]  
Input  
CLKIN  
Indicates address and control are valid.  
Output  
Output  
Output  
Input  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
Read data.  
The identification tag for the read data group of signals.  
Indicates the last transfer in a read burst.  
RLASTS  
RREADYS  
Read ready signal indicating that the bus master can accept read  
data and response information.  
RRESPS[1:0]  
RVALIDS  
Output  
Output  
CLKIN  
CLKIN  
Read response.  
Indicates address and control are valid.  
A.5.4  
AXI slave port error detection signals  
Table A-7 shows the AXI slave port error detection signals. These signals are only generated if  
the processor is configured to include AXI bus parity. See Configurable options on page 1-13  
for more information.  
Table A-7 AXI slave port error detection signals  
Direction Clocking Description  
Signal  
AWPARITYS  
WPARITYS  
BPARITYS  
ARPARITYS  
RPARITYS  
Input  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
Parity bit for write address channel  
Parity bit for write data channel  
Parity bit for write response channel  
Parity bit for read address channel  
Parity bit for read data channel  
Input  
Output  
Input  
Output  
AXISPARERR[2:0] Output  
Parity error indication for read address (bit [2]), write data (bit [1]),  
and write address (bit [0]) channels.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
A-12  
   
Processor Signal Descriptions  
A.6  
TCM interface signals  
Table A-8 shows the ATCM port signals.  
Table A-8 ATCM port signals  
Name  
Direction Clocking Description  
ATCDATAIN [63:0]  
ATCPARITYIN [13:0]  
ATCERROR  
Input  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
Data from ATCM  
Input  
Parity or ECC code from ATCM  
Error detected by ATCMa  
Input  
ATCWAIT  
Input  
Wait from ATCM  
Late error from ATCMa  
ATCLATEERROR  
ATCRETRY  
Input  
Access to ATCM must be retrieda  
Parity formed from ATCM address outputb  
Enable for ATCM lower word, bit range [31:0]  
Enable for ATCM upper word, bit range [64:32]  
Write enable for ATCM  
Input  
ATCADDRPTY  
ATCEN0  
Output  
Output  
Output  
Output  
Output  
Output  
Output  
Output  
Output  
Output  
ATCEN1  
ATCWE  
ATCADDR [22:3]  
ATCBYTEWR [7:0]  
ATCSEQ  
Address for ATCM data RAM  
Byte strobes for direct write  
ATCM RAM access is sequential  
Write data for ATCM data RAM  
Write parity or ECC code for ATCM  
ATCDATAOUT [63:0]  
ATCPARITYOUT [13:0]  
ATCACCTYPE[2:0]  
Determines access type:  
b001 = Load/Store  
b010 = Fetch  
b100 = DMA  
b100 = MBISTc.  
a. This signal is ignored when bit [0] of the Auxiliary Control Register is set to 0, see c1, Auxiliary Control  
b. Only generated if the processor is configured to include TCM address bus parity.  
c. The MBIST interface has no way of signalling a wait. If it is accessing the TCM, and the TCM signals a wait,  
the AXI slave pipeline stalls and the data arrives later. However, no signal is sent to the MBIST controller to  
indicate this.  
Table A-9 B0TCM port signals  
Name  
Direction Clocking Description  
B0TCDATAIN [63:0]  
B0TCPARITYIN [13:0]  
B0TCERROR  
Input  
Input  
Input  
Input  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
Data from B0TCM  
Parity or ECC code from B0TCM  
Error detected by B0TCMa  
Wait from B0TCM  
B0TCWAIT  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
A-13  
               
Processor Signal Descriptions  
Table A-9 B0TCM port signals (continued)  
Name  
Direction Clocking Description  
Late error from B0TCMa  
B0TCLATEERROR  
B0TCRETRY  
Input  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
Access to B1TCM must be retrieda  
Parity formed from B0TCM address outputb  
Write enable for B0TCM  
Input  
B0TCADDRPTY  
B0TCWE  
Output  
Output  
Output  
Output  
Output  
Output  
Output  
Output  
B0TCEN0  
Enable for B0TCM lower word, bit range [31:0]  
Enable for B0TCM upper word, bit range [64:32]  
Address for B0TCM data RAM  
B0TCEN1  
B0TCADDR [22:3]  
B0TCBYTEWR [7:0]  
B0TCSEQ  
Byte strobes for direct write  
B0TCM RAM access is sequential  
Write data for B0TCM data RAM  
Write parity or ECC code for B0TCM  
B0TCDATAOUT [63:0]  
B0TCPARITYOUT [13:0] Output  
B0TCACCTYPE[2:0] Output  
Determines access type:  
b001 = Load/Store  
b010 = Fetch  
b100 = DMA  
b100 = MBISTc.  
a. This signal is ignored when bit [1] of the Auxiliary Control Register is set to 0, see c1, Auxiliary Control Register  
b. Only generated if the processor is configured to include TCM address bus parity.  
c. The MBIST interface has no way of signalling a wait. If it is accessing the TCM, and the TCM signals a wait, the  
AXI slave pipeline stalls and the data arrives later. However, no signal is sent to the MBIST controller to indicate  
this.  
Table A-10 B1TCM port signals  
Name  
Direction Clocking Description  
B1TCDATAIN [63:0]  
B1TCPARITYIN [13:0]  
B1TCERROR  
B1TCRETRY  
B1TCLATEERROR  
B1TCWAIT  
Input  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
Data from B1TCM  
Input  
Parity or ECC code from B1TCM  
Error detected by B1TCMa  
Input  
Access to B1TCM must be retrieda  
Late error from B1TCMa  
Input  
Input  
Input  
Wait from B1TCM  
Parity formed from B1TCM address outputb  
Write enable for B1TCM  
B1TCADDRPTY  
B1TCWE  
Output  
Output  
Output  
Output  
B1TCEN0  
Enable for B1TCM lower word, bit range [31:0]  
Enable for B1TCM upper word, bit range [64:32]  
B1TCEN1  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
A-14  
     
Processor Signal Descriptions  
Table A-10 B1TCM port signals (continued)  
Name  
Direction Clocking Description  
B1TCADDR [22:3]  
B1TCBYTEWR [7:0]  
B1TCSEQ  
Output  
Output  
Output  
Output  
Output  
Output  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
Address for B1TCM data RAM  
Byte strobes for direct write  
B1TCM RAM access is sequential  
Write data for B1TCM data RAM  
Write parity or ECC code for B1TCM  
B1TCDATAOUT [63:0]  
B1TCPARITYOUT [13:0]  
B1TCACCTYPE[2:0]  
Determines access type:  
b001 = Load/Store  
b010 = Fetch  
b100 = DMA  
b100 = MBISTc.  
a. This signal is ignored when bit [2] of the Auxiliary Control Register is set to 0, see c1, Auxiliary Control Register  
b. Only generated if the processor is configured to include TCM address bus parity.  
c. The MBIST interface has no way of signalling a wait. If it is accessing the TCM, and the TCM signals a wait, the  
AXI slave pipeline stalls and the data arrives later. However, no signal is sent to the MBIST controller to indicate  
this.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
A-15  
Processor Signal Descriptions  
A.7  
Dual core interface signals  
Table A-11 shows the dual redundant core interface signals.  
Table A-11 Dual core interface signals  
Direction Clocking Description  
Signal  
a
a
a
a
DCCMINP[7:0]  
DCCMOUT[7:0]  
DCCMINP2[7:0]  
Input  
Dual core compare logic input control bus  
Dual core compare logic output control bus  
Dual core compare logic extra input control busb  
Dual core compare logic extra output control busb  
-
-
-
-
Output  
Input  
DCCMOUT2[7:0] Output  
a. Implementation-defined.  
b. Not available in r0px revisions of the processor.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
A-16  
           
Processor Signal Descriptions  
A.8  
Debug interface signals  
Table A-12 shows the debug interface signals. With the exception of PCLKDBG,  
PCLKENDBG and PRESETDBGn, all these signals are only sampled or driven on  
PCLKDBG edges when PCLKENDBG is asserted.  
Table A-12 Debug interface signals  
Signal  
Direction Clocking  
Description  
PCLKDBG  
Input  
Input  
Input  
Input  
Input  
Output  
Input  
Input  
Output  
Output  
Input  
-
Debug clock.  
PCLKENDBG  
PSELDBG  
PCLKDBG Clock enable for PCLKDBG.  
PCLKDBG Selects the external debug interface.  
PCLKDBG Programming address.  
PADDRDBG[11:2]  
PADDRDBG31  
PRDATADBG[31:0]  
PWDATADBG[31:0]  
PENABLEDBG  
PREADYDBG  
PSLVERRDBG  
PWRITEDBG  
PCLKDBG Programming address.  
PCLKDBG  
Read data bus.  
PCLKDBG Write data bus.  
PCLKDBG Indicates second, and subsequent, cycle of a transfer.  
PCLKDBG Extends a APB transfer by the inserting wait states.  
PCLKDBG Slave-generated error response.  
PCLKDBG Indicates access is a write transfer.  
Distinguishes between a read, LOW, and a write, HIGH.  
PRESETDBGn  
Input  
Any  
Reset debug logic.  
Table A-13 shows the debug miscellaneous signals.  
Table A-13 Debug miscellaneous signals  
Name  
Direction Clocking  
Description  
DBGEN  
Input  
Any  
Debug enable  
NIDEN  
Input  
Any  
Non-invasive debug enable  
External debug request  
Debug acknowledge  
EDBGRQ  
Input  
Any  
DBGACK  
Output  
Output  
Output  
Output  
Output  
Input  
CLKIN  
DBGRSTREQa  
DBGTRIGGER  
COMMRX  
PCLKDBG Request for reset from debug logic  
CLKIN  
CLKIN  
CLKIN  
External debug request taken  
Write-DTR full  
COMMTX  
Read-DTR empty  
DBGRESTART  
DBGRESTARTED  
DBGNOPWRDWN  
External restart request  
Handshake for DBGRESTART  
Output  
Output  
CLKIN  
PCLKDBG No power-down request  
Tie-off Debug ROM physical address  
DBGROMADDR[31:12] Input  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
A-17  
               
Processor Signal Descriptions  
Table A-13 Debug miscellaneous signals (continued)  
Name  
Direction Clocking  
Description  
DBGROMADDRV  
Input  
Tie-off  
Tie-off  
Tie-off  
Debug ROM physical address valid  
Debug self-address offset  
DBGSELFADDR[31:12] Input  
DBGSELFADDRV Input  
Debug self-address offset valid  
a. Not available in r0px revisions of the processor.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
A-18  
Processor Signal Descriptions  
A.9  
ETM interface signals  
Table A-14 shows the ETM interface signals.  
Table A-14 ETM interface signals  
Signal  
Direction Clocking Description  
ETMICTL[13:0]  
ETMIA[31:1]  
Output  
Output  
Output  
Output  
Output  
Output  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
ETM instruction control bus  
ETM instruction address  
ETMDCTL[11:0]  
ETMDA[31:0]  
ETMDD[63:0]  
ETMCID[31:0]  
ETM data control bus  
ETM data address  
ETM data-data  
Current value of processor CID register  
Core is attempting to enter WFI state  
Performance monitor unit output  
Power up ETM interface  
ETMWFIPENDING Output  
EVNTBUS[46:0]  
ETMPWRUP  
Output  
Input  
Input  
Input  
nETMWFIREADY  
ETMEXTOUT[1:0]  
ETM FIFO is empty, core can enter WFI state  
ETM detected events  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
A-19  
       
Processor Signal Descriptions  
A.10 Test signals  
Table A-15 Test signals  
Signal  
SE  
Direction Clocking Description  
a
a
Input  
Scan Enable  
-
-
RSTBYPASS Input  
Bypass pipelined reset  
a. Design for test only.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
A-20  
         
Processor Signal Descriptions  
A.11 MBIST signals  
Table A-16 MBIST signals  
Signal  
Direction Clocking Description  
MBTESTON  
Input  
Input  
Input  
Input  
Input  
Input  
Output  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
MBIST test is enabled  
MBIST data in  
MBISTDIN[77:0]  
MBISTADDR[19:0]  
MBISTCE  
MBIST address  
MBIST chip enable  
MBIST chip select  
MBIST write enable  
MBIST data out  
MBISTSEL[4:0]  
MBISTWE [7:0]  
MBISTDOUT[77:0]  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
A-21  
       
Processor Signal Descriptions  
A.12 Validation signals  
Table A-17 shows the validation signals.  
Table A-17 Validation signals  
Signal  
Direction Clocking Description  
VALEDBGRQ Output  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
Debug request  
nVALIRQ  
nVALFIQ  
Output  
Output  
Output  
Request for an interrupt  
Request for a Fast Interrupt  
Request for a reset  
nVALRESET  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
A-22  
       
Processor Signal Descriptions  
A.13 FPU signals  
Table A-18 shows the FPU signals. These signals are only driven if the processor is configured  
to include the floating-point logic.  
Table A-18 FPU signals  
Signal  
Direction Clocking Description  
FPIXC  
Output  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
CLKIN  
Masked floating-point inexact exception  
FPOFC Output  
Masked floating-point overflow exception  
Masked floating-point underflow exception  
Masked floating-point invalid operation exception  
Masked floating-point divide-by-zero exception  
Masked floating-point input denormal exception  
FPUFC Output  
FPIOC  
Output  
FPDZC Output  
FPIDC Output  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
A-23  
       
Appendix B  
ECC Schemes  
This appendix describes some of the advantages and disadvantages of the different Error Checking  
and Correction (ECC) schemes for the TCMs. It contains the following section:  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
B-1  
   
ECCSchemes  
B.1  
ECC scheme selection guidelines  
When deciding to implement a Cortex-R4 processor with an ECC scheme on one or both of the  
TCM interfaces, give careful consideration between using 32-bit or 64-bit ECC. To calculate or  
check the ECC code for data, the processor must know the value of all bytes in the data chunk  
protected by the scheme. Therefore, when using these schemes, the processor must perform  
additional read accesses to calculate and check the ECC code stored with the data.  
For example, if the ATCM is implemented with 32-bit ECC and a program performs an aligned  
STRto the memory, the processor can calculate the error correction code using only the data  
stored by the program.  
If the same memory was implemented with 64-bit ECC, the processor cannot calculate the ECC  
code for the doubleword memory chunk being written using only the data stored by the program.  
To calculate the ECC code and store the data, the processor must first perform a read of the other  
word in that memory chunk. This increases the number of memory accesses required to execute  
the program. This increases power consumption, and can also lead to a decrease in performance.  
Use the following guidelines to decide which scheme to use. If you are in any doubt, benchmark  
your system running typical software to find the best balance between area, power, and  
performance for your application.  
For a TCM interface that contains mainly instructions, use 64-bit ECC. The vast majority  
of reads requested by the prefetch unit are doubleword.  
Use 64-bit ECC when a TCM contains data that is accessed using:  
LDRDor STRDinstructions where the start address is doubleword aligned  
LDM or STMinstructions where the start address is doubleword aligned and there are  
an even number of registers in the register list.  
64-bit ECC requires less RAM area, and does not provide any performance loss or  
increased power consumption over 32-bit ECC in these cases.  
When LDMand STMinstructions are used to access many registers, the majority of TCM  
accesses do not require additional reads with 64-bit ECC.  
32-bit ECC provides better power consumption and generally better performance  
compared to 64-bit ECC when:  
a program performs many unaligned accesses to data in a TCM  
a program performs many byte, halfword, and word accesses to data in a TCM.  
You might be able to obtain optimal results by using a different error detection scheme on each  
TCM interface, and allocating instructions and data to each interface based on the guidelines  
given above.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
B-2  
   
Appendix C  
Revisions  
This appendix describes the technical changes between released issues of this book.  
Table C-1 Differences between issue B and issue C  
Location  
Change  
Clarified the description of Thumb-2 technology and Thumb instructions  
Clarified byte-invariant big-endian format  
Clarified little-endian format  
nCPUHALT removed from timing diagram  
Added sections  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
C-1  
     
Revisions  
Table C-1 Differences between issue B and issue C (continued)  
Change  
Location  
Updated reset value information for:  
Cache Type Register  
MPU Type Register  
Instruction Set Attributes Register 1  
Instruction Set Attributes Register 4  
Current Cache Size Identification Register  
Current Cache Level ID Register  
MPU Region Base Address Registers  
MPU Region Size and Enable Register  
MPU Region Access Control Register  
MPU Memory Region Number  
ATCM Region Register  
BTCM Region Register  
TCM selection Register  
Performance Monitor Control Register  
Software Increment Register  
User read/write Thread and Process ID Register  
User read-only Thread and Process ID Register  
Privileged-only Thread and Process ID Register  
Secondary Auxiliary Control Register  
Build Options 1 Register  
Build Options 2 Register  
Correctable Fault Location Register  
Updated Type information for the Coprocessor Access Register  
Clarified the description of the Instruction Set Attributes Register 3  
Clarified functions for bits [31], [30], [29], and 28]  
Clarified functions for bits [20], [19], [18], [17], [16], [3], and [2]  
Clarified instructions that the PFU recognizes as procedure calls and  
procedure returns  
Added reference to Application Note 204  
Added section  
Clarified the description of region attributes  
Clarified the description of store buffer draining  
Clarified the encodings for some signals  
Clarified the number of Identifiers used for AXI bus accesses  
Clarified the description of the handling of TCM external faults  
Added dormant mode description  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
C-2  
Revisions  
Table C-1 Differences between issue B and issue C (continued)  
Location  
Change  
Added section  
Updated the permitted instruction combinations  
Updated the descriptions for COMMRX and COMMTX signals  
Table C-2 Differences between issue C and issue D  
Change  
Location  
No technical changes  
-
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
C-3  
 
Glossary  
This glossary describes some of the terms and abbreviations used in this manual. Where terms can  
have several meanings, the meaning presented here is intended.  
Abort  
A mechanism that indicates to a processor that the value associated with a memory access is  
invalid. An abort can be caused by the external or internal memory system as a result of attempting  
to access invalid instruction or data memory. An abort is classified as either a Prefetch or Data  
Abort, and an internal or External Abort.  
See also Data Abort, External Abort and Prefetch Abort.  
Abort model  
An abort model is the defined behavior of an ARM processor in response to a Data Abort exception.  
Different abort models behave differently with regard to load and store instructions that specify  
base register write-back.  
Addressing modes  
A mechanism, shared by many different instructions, for generating values used by the instructions.  
For four of the ARM addressing modes, the values generated are memory addresses (which is the  
traditional role of an addressing mode). A fifth addressing mode generates values to be used as  
operands by data-processing instructions.  
Advanced eXtensible Interface (AXI)  
This is a bus protocol that supports separate address/control and data phases, unaligned data  
transfers using byte strobes, burst-based transactions with only start address issued, separate read  
and write data channels to enable low-cost DMA, ability to issue multiple outstanding addresses,  
out-of-order transaction completion, and easy addition of register stages to provide timing closure.  
The AXI protocol also includes optional extensions to cover signaling for low-power operation.  
AXI is targeted at high performance, high clock frequency system designs and includes a number  
of features that make it very suitable for high speed sub-micron interconnect.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
Glossary-1  
 
Glossary  
Advanced High-performance Bus (AHB)  
The AMBA Advanced High-performance Bus system connects embedded processors such as  
an ARM core to high-performance peripherals, DMA controllers, on-chip memory, and  
interfaces. It is a high-speed, high-bandwidth bus that supports multi-master bus management  
to maximize system performance.  
See also Advanced Microcontroller Bus Architecture.  
Advanced Microcontroller Bus Architecture (AMBA)  
AMBA is the ARM open standard for multi-master on-chip buses, capable of running with  
multiple masters and slaves. It is an on-chip bus specification that details a strategy for the  
interconnection and management of functional blocks that make up a System-on-Chip (SoC). It  
aids in the development of embedded processors with one or more CPUs or signal processors  
and multiple peripherals. AMBA complements a reusable design methodology by defining a  
common backbone for SoC modules. AHB, APB, and AXI conform to this standard.  
Advanced Peripheral Bus (APB)  
The AMBA Advanced Peripheral Bus is a simpler bus protocol than AHB. It is designed for use  
with ancillary or general-purpose peripherals such as timers, interrupt controllers, UARTs, and  
I/O ports. Connection to the main system bus is through a system-to-peripheral bus bridge that  
helps to reduce system power consumption.  
See also Advanced High-performance Bus.  
AHB  
See Advanced High-performance Bus.  
Aligned  
A data item stored at an address that is divisible by the number of bytes that defines the data size  
is said to be aligned. Aligned words and halfwords have addresses that are divisible by four and  
two respectively. The terms word-aligned and halfword-aligned therefore stipulate addresses  
that are divisible by four and two respectively.  
AMBA  
APB  
See Advanced Microcontroller Bus Architecture.  
See Advanced Peripheral Bus.  
Application Specific Integrated Circuit (ASIC)  
An integrated circuit that has been designed to perform a specific application function. It can be  
custom-built or mass-produced.  
Architecture  
The organization of hardware and/or software that characterizes a processor and its attached  
components, and enables devices with similar characteristics to be grouped together when  
describing their behavior, for example, Harvard architecture, instruction set architecture,  
ARMv6 architecture.  
ARM instruction  
ARM state  
A word that specifies an operation for an ARM processor to perform. ARM instructions must  
be word-aligned.  
A processor that is executing ARM (32-bit) word-aligned instructions is operating in ARM  
state.  
ASIC  
AXI  
See Application Specific Integrated Circuit.  
See Advanced eXstensible Interface.  
AXI channel order and interfaces  
The block diagram shows:  
the order in which AXI channel signals are described  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
Glossary-2  
Glossary  
the master and slave interface conventions for AXI components.  
Write address channel (AW)  
Write data channel (W)  
Write response channel (B)  
Read address channel (AR)  
Read data channel (R)  
Write address channel (AW)  
Write data channel (W)  
Write response channel (B)  
Read address channel (AR)  
Read data channel (R)  
AXI  
master  
AXI  
interconnect  
AXI  
slave  
AXI master  
interface  
AXI slave  
interface  
AXI master  
interface  
AXI slave  
interface  
AXI terminology  
The following AXI terms are general. They apply to both masters and slaves:  
Active read transaction  
A transaction for which the read address has transferred, but the last read data has  
not yet transferred.  
Active transfer  
A transfer for which the xVALID1 handshake has asserted, but for which  
xREADY has not yet asserted.  
Active write transaction  
A transaction for which the write address and/or leading write data has  
transferred, but the write response has not yet transferred.  
Completed transfer  
A transfer for which the xVALID/xREADY handshake is complete.  
Payload  
The non-handshake signals in a transfer.  
Transaction An entire burst of transfers, comprising an address, one or more data transfers and  
a response transfer (writes only).  
Transmit  
Transfer  
An initiator driving the payload and asserting the relevant xVALID signal.  
A single exchange of information. That is, with one xVALID/xREADY  
handshake.  
The following AXI terms are master interface attributes. To obtain optimum performance, they  
must be specified for all components with an AXI master interface:  
Combined issuing capability  
The maximum number of active transactions that a master interface can generate.  
This is specified instead of write or read issuing capability for master interfaces  
that use a combined storage for active write and read transactions.  
Read ID capability  
The maximum number of different ARID values that a master interface can  
generate for all active read transactions at any one time.  
1. The letter x in the signal name denotes an AXI channel as follows:  
AW  
W
B
Write address channel.  
Write data channel.  
Write response channel.  
Read address channel.  
Read data channel.  
AR  
R
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
Glossary-3  
Glossary  
Read ID width  
The number of bits in the ARID bus.  
Read issuing capability  
The maximum number of active read transactions that a master interface can  
generate.  
Write ID capability  
The maximum number of different AWID values that a master interface can  
generate for all active write transactions at any one time.  
Write ID width  
The number of bits in the AWID and WID buses.  
Write interleave capability  
The number of active write transactions for which the master interface is capable  
of transmitting data. This is counted from the earliest transaction.  
Write issuing capability  
The maximum number of active write transactions that a master interface can  
generate.  
The following AXI terms are slave interface attributes. To obtain optimum performance, they  
must be specified for all components with an AXI slave interface  
Combined acceptance capability  
The maximum number of active transactions that a slave interface can accept.  
This is specified instead of write or read acceptance capability for slave interfaces  
that use a combined storage for active write and read transactions.  
Read acceptance capability  
The maximum number of active read transactions that a slave interface can  
accept.  
Read data reordering depth  
The number of active read transactions for which a slave interface can transmit  
data. This is counted from the earliest transaction.  
Write acceptance capability  
The maximum number of active write transactions that a slave interface can  
accept.  
Write interleave depth  
The number of active write transactions for which the slave interface can receive  
data. This is counted from the earliest transaction.  
Banked registers  
Base register  
Those physical registers whose use is defined by the current processor mode. The banked  
registers are R8 to R14.  
A register specified by a load/store instruction that is used to hold the base value for the  
instruction’s address calculation. Depending on the instruction and its addressing mode, an  
offset can be added to or subtracted from the base register value to form the virtual address that  
is sent to memory.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
Glossary-4  
Glossary  
Base register write-back  
Updating the contents of the base register used in an instruction target address calculation so that  
the modified address is changed to the next higher or lower sequential address in memory. This  
means that it is not necessary to fetch the target address for successive instruction transfers and  
enables faster burst accesses to sequential memory.  
Beat  
Alternative word for an individual transfer within a burst. For example, an INCR4 burst  
comprises four beats.  
See also Burst.  
BE-8  
Big-endian view of memory in a byte-invariant system.  
See also BE-32, LE, Byte-invariant and Word-invariant.  
Big-endian view of memory in a word-invariant system.  
See also BE-8, LE, Byte-invariant and Word-invariant.  
BE-32  
Big-endian  
Byte ordering scheme in which bytes of decreasing significance in a data word are stored at  
increasing addresses in memory.  
See also Little-endian and Endianness.  
Big-endian memory  
Block address  
Memory in which:- a byte or halfword at a word-aligned address is the most significant byte or  
halfword within the word at that address - a byte at a halfword-aligned address is the most  
significant byte within the halfword at that address.  
See also Little-endian memory.  
An address that comprises a tag, an index, and a word field. The tag bits identify the way that  
contains the matching cache entry for a cache hit. The index bits identify the set being  
addressed. The word field contains the word address that can be used to identify specific words,  
halfwords, or bytes within the cache entry.  
See also Cache terminology diagram on the last page of this glossary.  
Branch prediction  
The process of predicting if conditional branches are to be taken or not in pipelined processors.  
Successfully predicting if branches are to be taken enables the processor to prefetch the  
instructions following a branch before the condition is fully resolved. Branch prediction can be  
done in software or by using custom hardware. Branch prediction techniques are categorized as  
static, in which the prediction decision is decided before run time, and dynamic, in which the  
prediction decision can change during program execution.  
Breakpoint  
A breakpoint is a mechanism provided by debuggers to identify an instruction at which program  
execution is to be halted. Breakpoints are inserted by the programmer to enable inspection of  
register contents, memory locations, variable values at fixed points in the program execution to  
test that the program is operating correctly. Breakpoints are removed after the program is  
successfully tested.  
See also Watchpoint.  
Burst  
A group of transfers to consecutive addresses. Because the addresses are consecutive, there is  
no requirement to supply an address for any of the transfers after the first one. This increases  
the speed at which the group of transfers can occur. Bursts over AHB or AXI buses are  
controlled using the xBURST signals to specify if transfers are single, four-beat, eight-beat, or  
16-beat bursts, and to specify how the addresses are incremented.  
See also Beat.  
Byte  
An 8-bit data item.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
Glossary-5  
Glossary  
Byte invariant  
In a byte-invariant system, the address of each byte of memory remains unchanged when  
switching between little-endian and big-endian operation. When a data item larger than a byte  
is loaded from or stored to memory, the bytes making up that data item are arranged into the  
correct order depending on the endianness of the memory access. The ARM architecture  
supports byte-invariant systems in ARMv6 and later versions. When byte-invariant support is  
selected, unaligned halfword and word memory accesses are also supported. Multi-word  
accesses are expected to be word-aligned.  
See also Word-invariant.  
Byte lane strobe  
An AXI signal, WSTRB, that is used for unaligned or mixed-endian data accesses to determine  
which byte lanes are active in a transfer. One bit of WSTRB corresponds to eight bits of the data  
bus.  
Byte swizzling  
Cache  
The reverse ordering of bytes in a word.  
A block of on-chip or off-chip fast access memory locations, situated between the processor and  
main memory, used for storing and retrieving copies of often used instructions and/or data. This  
is done to greatly increase the average speed of memory accesses and so improve processor  
performance.  
See also Cache terminology diagram on the last page of this glossary.  
Cache contention  
When the number of frequently-used memory cache lines that use a particular cache set exceeds  
the set-associativity of the cache. In this case, main memory activity increases and performance  
decreases.  
Cache hit  
A memory access that can be processed at high speed because the instruction or data that it  
addresses is already held in the cache.  
Cache line  
The basic unit of storage in a cache. It is always a power of two words in size (usually four or  
eight words), and is required to be aligned to a suitable memory boundary.  
See also Cache terminology diagram on the last page of this glossary.  
Cache line index  
The number associated with each cache line in a cache set. Within each cache set, the cache lines  
are numbered from 0 to (set associativity) -1.  
See also Cache terminology diagram on the last page of this glossary.  
Cache miss  
Cache set  
A memory access that cannot be processed at high speed because the instruction/data it  
addresses is not in the cache and a main memory access is required.  
A cache set is a group of cache lines (or blocks). A set contains all the ways that can be  
addressed with the same index. The number of cache sets is always a power of two. All sets are  
accessed in parallel during a cache look-up.  
See also Cache terminology diagram on the last page of this glossary.  
Cache set associativity  
The maximum number of cache lines that can be held in a cache set.  
See also Set-associative cache and Cache terminology diagram on the last page of this glossary.  
A group of cache lines (or blocks). It is 2 to the power of the number of index bits in size.  
See also Cache terminology diagram on the last page of this glossary.  
See Victim.  
Cache way  
Cast out  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
Glossary-6  
Glossary  
Clean  
A cache line that has not been modified while it is in the cache is said to be clean. To clean a  
cache is to write dirty cache entries into main memory. If a cache line is clean, it is not written  
on a cache miss because the next level of memory contains the same data as the cache.  
See also Dirty.  
Clock gating  
Gating a clock signal for a macrocell with a control signal (such as PWRDOWN) and using the  
modified clock that results to control the operating state of the macrocell.  
Clocks Per Instruction (CPI)  
See Cycles Per Instruction (CPI).  
Coherency  
Cold reset  
See Memory coherency.  
Also known as power-on reset. Starting the processor by turning power on. Turning power off  
and then back on again clears main memory and many internal settings. Some program failures  
can lock up the processor and require a cold reset to enable the system to be used again. In other  
cases, only a warm reset is required.  
See also Warm reset.  
Communications channel  
Software running on an ARM processor uses this to communicate with an external host through  
the debug interface. It can also be called the Debug Communications Channel. It is  
architecture-defined. See the ARM Architecture Reference Manual and your product technical  
reference manual for specific information.  
Condition field  
A 4-bit field in an instruction that is used to specify a condition under which the instruction can  
execute.  
Conditional execution  
If the condition code flags indicate that the corresponding condition is true when the instruction  
starts executing, it executes normally. Otherwise, the instruction does nothing.  
Context  
The environment that each process operates in for a multitasking operating system. In ARM  
processors, this is limited to mean the physical address range that it can access in memory and  
the associated memory access permissions.  
See also Fast context switch.  
Control bits  
The bottom eight bits of a Program Status Register (PSR). The control bits change when an  
exception arises and can be altered by software only when the processor is in a Privileged mode.  
Coprocessor  
A processor that supplements the main processor. It carries out additional functions that the  
main processor cannot perform. Usually used for floating-point math calculations, signal  
processing, or memory management.  
Copy back  
See Write-back.  
Core module  
In the context of an ARM Integrator, a core module is an add-on development board that  
contains an ARM processor and local memory. Core modules can run standalone, or can be  
stacked onto Integrator motherboards.  
Core reset  
CPI  
See Warm reset.  
See Cycles per instruction.  
See Current Program Status Register.  
CPSR  
Current Program Status Register (CPSR)  
The register that holds the current operating processor status.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
Glossary-7  
Glossary  
Cycles Per instruction (CPI)  
Cycles per instruction (or clocks per instruction) is a measure of the number of computer  
instructions that can be performed in one clock cycle. This figure of merit can be used to  
compare the performance of different CPUs that implement the same instruction set against each  
other. The lower the value, the better the performance.  
CoreSight  
Data Abort  
The infrastructure for monitoring, tracing, and debugging a complete system on chip.  
An indication from a memory system to the processor of an attempt to access an illegal data  
memory location. An exception must be taken if the processor attempts to use the data that  
caused the abort.  
See also Abort, External Abort, and Prefetch Abort.  
Data cache  
A block of on-chip fast access memory locations, situated between the processor and main  
memory, used for storing and retrieving copies of often used data. This is done to greatly  
increase the average speed of memory accesses and so improve processor performance.  
Debugger  
A debugging system that includes a program, used to detect, locate, and correct software faults,  
together with custom hardware that supports software debugging.  
Default NaN mode  
A mode in which all operations that result in a NaN return the default NaN, regardless of the  
cause of the NaN result. This mode is compliant with the IEEE 754 standard but implies that all  
information contained in any input NaNs to an operation is lost.  
Denormalized value  
Dirty  
See Subnormal value.  
A cache line in a write-back cache that has been modified while it is in the cache is said to be  
dirty. A cache line is marked as dirty by setting the dirty bit. If a cache line is dirty, it must be  
written to memory on a cache miss because the next level of memory contains data that has not  
been updated. The process of writing dirty data to main memory is called cache cleaning.  
See also Clean.  
Disabled exception  
An exception is disabled when its exception enable bit in the FPCSR is not set. For these  
exceptions, the IEEE 754 standard defines the result to be returned. An operation that generates  
an exception condition can bounce to the support code to produce the result defined by the IEEE  
754 standard. The exception is not reported to the user trap handler.  
DNM  
See Do Not Modify.  
Do Not Modify (DNM)  
In Do Not Modify fields, the value must not be altered by software. DNM fields read as  
Unpredictable values, and must only be written with the same value read from the same field on  
the same processor. DNM fields are sometimes followed by RAZ or RAO in parentheses to  
show which way the bits should read for future compatibility, but programmers must not rely on  
this behavior.  
Double-precision value  
Doubleword  
Consists of two 32-bit words that must appear consecutively in memory and must both be  
word-aligned, and that is interpreted as a basic double-precision floating-point number  
according to the IEEE 754-1985 standard.  
A 64-bit data item. The contents are taken as being an unsigned integer unless otherwise stated.  
Embedded Trace Macrocell (ETM)  
A hardware macrocell that, when connected to a processor core, outputs instruction and data  
trace information on a trace port. The ETM provides processor driven trace through a trace port  
compliant to the ATB protocol.  
EmbeddedICE-RT  
The JTAG-based hardware provided by debuggable ARM processors to aid debugging in  
real-time.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
Glossary-8  
Glossary  
Enabled exception  
Endianness  
An exception is enabled when its exception enable bit in the FPCSR is set. When an enabled  
exception occurs, a trap to the user handler is taken. An operation that generates an exception  
condition might bounce to the support code to produce the result defined by the IEEE 754  
standard. The exception is then reported to the user trap handler.  
Byte ordering. The scheme that determines the order in which successive bytes of a data word  
are stored in memory. An aspect of the system’s memory mapping.  
See also Little-endian and Big-endian  
ETM  
See Embedded Trace Macrocell.  
Event  
1.  
(Simple) An observable condition that can be used by an ETM to control aspects of a  
trace.  
2.  
(Complex) A boolean combination of simple events that is used by an ETM to control  
aspects of a trace.  
Exception  
A fault or error event that is considered serious enough to require that program execution is  
interrupted. Examples include attempting to perform an invalid memory access, external  
interrupts, and Undefined instructions. When an exception occurs, normal program flow is  
interrupted and execution is resumed at the corresponding exception vector. This contains the  
first instruction of the interrupt handler to deal with the exception.  
Exception service routine  
See Interrupt handler.  
Exception vector  
Exponent  
See Interrupt vector.  
The component of a floating-point number that normally signifies the integer power to which  
two is raised in determining the value of the represented number.  
External Abort  
An indication from an external memory system to a core that the value associated with a  
memory access is invalid. An external abort is caused by the external memory system as a result  
of attempting to access invalid memory.  
See also See also Abort, Data Abort and Prefetch Abort  
Halfword  
A 16-bit data item.  
Halt mode  
One of two mutually exclusive debug modes. In halt mode all processor execution halts when a  
breakpoint or watchpoint is encountered. All processor state, coprocessor state, memory and  
input/output locations can be examined and altered by the JTAG interface.  
See also Monitor mode.  
High vectors  
Alternative locations for exception vectors. The high vector address range is near the top of the  
address space, rather than at the bottom.  
Hit-Under-Miss (HUM)  
A buffer that enables program execution to continue, even though there has been a data miss in  
the cache.  
Host  
A computer that provides data and other services to another computer. Especially, a computer  
providing debugging services to a target being debugged.  
HUM  
See Hit-Under-Miss.  
IEEE 754 standard  
IEEE Standard for Binary Floating-Point Arithmetic, ANSI/IEEE Std 754-1985. The standard  
that defines data types, correct operation, exception types and handling, and error bounds for  
floating-point systems. Most processors are built in compliance with the standard either in  
hardware or in a combination of hardware and software.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
Glossary-9  
Glossary  
Illegal instruction  
An instruction that is architecturally Undefined.  
Implementation-defined  
Means that the behavior is not architecturally defined, but should be defined and documented  
by individual implementations.  
Implementation-specific  
Means that the behavior is not architecturally defined, and does not have to be documented by  
individual implementations. Used when there are a number of implementation options available  
and the option chosen does not affect software compatibility.  
Infinity  
In the IEEE 754 standard format to represent infinity, the exponent is the maximum for the  
precision and the fraction is all zeros.  
Input exception  
Instruction cache  
An exception condition in which one or more of the operands for a given operation are not  
supported by the hardware. The operation bounces to support code for processing.  
A block of on-chip fast access memory locations, situated between the processor and main  
memory, used for storing and retrieving copies of often used instructions. This is done to greatly  
increase the average speed of memory accesses and so improve processor performance.  
Instruction Synchronization Barrier (ISB)  
An operation to ensure that the prefetch buffer is flushed of all out-of-date instructions.  
Intermediate result  
An internal format used to store the result of a calculation before rounding. This format can have  
a larger exponent field and fraction field than the destination format.  
Interrupt handler  
Interrupt vector  
A program to which control of the processor is passed when an interrupt occurs.  
One of a number of fixed addresses in low memory, or in high memory if high vectors are  
configured, that contains the first instruction of the corresponding interrupt handler.  
Invalidate  
To mark a cache line as being not valid by clearing the valid bit. This must be done whenever  
the line does not contain a valid cache entry. For example, after a cache flush all lines are invalid.  
ISB  
LE  
See Instruction Synchronization Barrier.  
Little endian view of memory in both byte-invariant and word-invariant systems. See also  
Byte-invariant, Word-invariant.  
Line  
See Cache line.  
Little-endian  
Byte ordering scheme in which bytes of increasing significance in a data word are stored at  
increasing addresses in memory.  
See also Big-endian and Endianness.  
Little-endian memory  
Memory in which:  
a byte or halfword at a word-aligned address is the least significant byte or halfword  
within the word at that address  
a byte at a halfword-aligned address is the least significant byte within the halfword at that  
address.  
See also Big-endian memory.  
Load/store architecture  
A processor architecture where data-processing operations only operate on register contents, not  
directly on memory contents.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
Glossary-10  
Glossary  
Load Store Unit (LSU)  
The part of a processor that handles load and store transfers.  
LSU  
See Load Store Unit.  
Macrocell  
A complex logic block with a defined interface and behavior. A typical VLSI system comprises  
several macrocells (such as a processor, an ETM, and a memory block) plus application-specific  
logic.  
Memory coherency  
A memory is coherent if the value read by a data read or instruction fetch is the value that was  
most recently written to that location. Memory coherency is made difficult when there are  
multiple possible physical locations that are involved, such as a system that has main memory,  
a write buffer and a cache.  
Memory Protection Unit (MPU)  
Hardware that controls access permissions to blocks of memory. Unlike an MMU, an MPU does  
not translate virtual addresses to physical addresses.  
Microprocessor  
Miss  
See Processor.  
See Cache miss.  
Monitor debug-mode  
One of two mutually exclusive debug modes. In Monitor debug-mode the processor enables a  
software abort handler provided by the debug monitor or operating system debug task. When a  
breakpoint or watchpoint is encountered, this enables vital system interrupts to continue to be  
serviced while normal program execution is suspended.  
See also Halt mode.  
MPU  
NaN  
See Memory Protection Unit.  
Not a number. A symbolic entity encoded in a floating-point format that has the maximum  
exponent field and a nonzero fraction. An SNaN causes an invalid operand exception if used as  
an operand and a most significant fraction bit of zero. A QNaN propagates through almost every  
arithmetic operation without signaling exceptions and has a most significant fraction bit of one.  
Penalty  
The number of cycles in which no useful Execute stage pipeline activity can occur because the  
instruction flow is different from that assumed or predicted.  
Power-on reset  
Prefetching  
See Cold reset.  
In pipelined processors, the process of fetching instructions from memory to fill up the pipeline  
before the preceding instructions have finished executing. Prefetching an instruction does not  
mean that the instruction has to be executed.  
Prefetch Abort  
An indication from a memory system to the processor that an instruction has been fetched from  
an illegal memory location. An exception must be taken if the processor attempts to execute the  
instruction. A Prefetch Abort can be caused by the external or internal memory system as a  
result of attempting to access invalid instruction memory.  
See also Data Abort, External Abort and Abort.  
Processor  
Read  
A contraction of microprocessor. A processor includes the CPU or core, plus additional  
components such as memory, and interfaces. These are combined as a single macrocell, that can  
be fabricated on an integrated circuit.  
Reads are defined as memory operations that have the semantics of a load. That is, the ARM  
instructions LDM  
,
LDRD  
,
LDC  
,
LDR  
,
LDRT  
,
LDRSH  
,
LDRH  
,
LDRSB  
,
LDRB  
,
LDRBT  
,
LDREX  
,
RFE STREX, SWP, and  
,
SWPB, and the Thumb instructions LDM  
,
LDR  
,
LDRSH  
,
LDRH  
,
LDRSB  
,
LDRB, and POP  
.
Region  
A partition of instruction or data memory space.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
Glossary-11  
Glossary  
Reserved  
A field in a control register or instruction format is reserved if the field is to be defined by the  
implementation, or produces Unpredictable results if the contents of the field are not zero. These  
fields are reserved for use in future extensions of the architecture or are  
implementation-specific. All reserved bits not used by the implementation must be written as 0  
and are to be read as 0.  
Rounding mode  
The IEEE 754 standard requires all calculations to be performed as if to an infinite precision.  
For example, a multiply of two single-precision values must accurately calculate the significand  
to twice the number of bits of the significand. To represent this value in the destination  
precision, rounding of the significand is often required. The IEEE 754 standard specifies four  
rounding modes.  
In round-to-nearest mode, the result is rounded at the halfway point, with the tie case rounding  
up if it would clear the least significant bit of the significand, making it even.  
Round-towards-zero mode chops any bits to the right of the significand, always rounding down,  
and is used by the C, C++, and Java languages in integer conversions.  
Round-towards-plus-infinity mode and round-towards-minus-infinity mode are used in interval  
arithmetic.  
Saved Program Status Register (SPSR)  
The register that holds the CPSR of the task immediately before the exception occurred that  
caused the switch to the current mode.  
SBO  
See Should Be One.  
SBZ  
See Should Be Zero.  
Scan chain  
Set  
See Boundary scan chain.  
See Cache set.  
Set-associative cache  
In a set-associative cache, lines can only be placed in the cache in locations that correspond to  
the modulo division of the memory address by the number of sets. If there are n ways in a cache,  
the cache is termed n-way set-associative. The set-associativity can be any number greater than  
or equal to 1 and is not restricted to being a power of two.  
Short vector operation  
Should Be One (SBO)  
Should Be Zero (SBZ)  
An operation involving more than one destination register and perhaps more than one source  
register in the generation of the result for each destination.  
Should be written as 1 (or all 1s for bit fields) by software. Writing a 0 produces Unpredictable  
results.  
Should be written as 0 (or all 0s for bit fields) by software. Writing a 1 produces Unpredictable  
results.  
Should Be Zero or Preserved (SBZP)  
Should be written as 0 (or all 0s for bit fields) by software, or preserved by writing the same  
value back that has been previously read from the same field on the same processor.  
Significand  
SPSR  
The component of a binary floating-point number that consists of an explicit or implicit leading  
bit to the left of the implied binary point and a fraction field to the right.  
See Saved Program Status Register  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
Glossary-12  
Glossary  
Stride  
The stride field, FPSCR[21:20], specifies the increment applied to register addresses in short  
vector operations. A stride of 00, specifying an increment of +1, causes a short vector operation  
to increment each vector register by +1 for each iteration, while a stride of 11 specifies an  
increment of +2.  
Subnormal value  
Support code  
A value in the range (–2Emin < x < 2Emin), except for 0. In the IEEE 754 standard format for  
single-precision and double-precision operands, a subnormal value has a zero exponent and a  
nonzero fraction field. The IEEE 754 standard requires that the generation and manipulation of  
subnormal operands be performed with the same precision as normal operands.  
Software that must be used to complement the hardware to provide compatibility with the IEEE  
754 standard. The support code has a library of routines that performs supported functions, such  
as divide with unsupported inputs or inputs that might generate an exception, and as well as  
operations beyond the scope of the hardware. The support code has a set of exception handlers  
to process exceptional conditions in compliance with the IEEE 754 standard.  
Synchronization primitive  
Tag  
The memory synchronization primitive instructions are those instructions that are used to ensure  
memory synchronization. That is, the LDREX STREX, SWP, and SWPBinstructions.  
,
The upper portion of a block address used to identify a cache line within a cache. The block  
address from the CPU is compared with each tag in a set in parallel to determine if the  
corresponding line is in the cache. If it is, it is said to be a cache hit and the line can be fetched  
from cache. If the block address does not correspond to any of the tags, it is said to be a cache  
miss and the line must be fetched from the next level of memory.  
See also Cache terminology diagram on the last page of this glossary.  
TAP  
See Debug test access port.  
Thumb state  
A processor that is executing Thumb (16-bit and 32-bit) instructions is operating in Thumb  
state.  
Tightly coupled memory (TCM)  
An area of low latency memory that provides predictable instruction execution or data load  
timing in cases where deterministic performance is required. TCMs are suited to holding:  
critical routines (such as for interrupt handling)  
scratchpad data  
data types whose locality is not suited to caching  
critical data structures (such as interrupt stacks).  
Tiny  
A nonzero result or value that is between the positive and negative minimum normal values for  
the destination precision.  
Trace port  
Trap  
A port on a device, such as a processor or ASIC, used to output trace information.  
A exceptional condition that has the respective exception enable bit set in the FPSCR register.  
The user trap handler is executed.  
Unaligned  
Undefined  
A data item stored at an address that is not divisible by the number of bytes that defines the data  
size is said to be unaligned. For example, a word stored at an address that is not divisible by four.  
Indicates an instruction that generates an Undefined instruction trap. See the ARM Architecture  
Reference Manual for more information on ARM exceptions.  
UNP  
See Unpredictable.  
Unpredictable  
The result of an instruction or control register field value that cannot be relied upon.  
Unpredictable instructions or results must not represent security holes, or halt or hang the  
processor, or any parts of the system.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
Glossary-13  
Glossary  
Unsupported values  
Specific data values that are not processed by the hardware but bounced to the support code for  
completion. These data can include infinities, NaNs, subnormal values, and zeros. An  
implementation is free to select which of these values is supported in hardware fully or partially,  
or requires assistance from support code to complete the operation. Any exception resulting  
from processing unsupported data is trapped to user code if the corresponding exception enable  
bit for the exception is set.  
Victim  
A cache line, selected to be discarded to make room for a replacement cache line that is required  
as a result of a cache miss. The way in which the victim is selected for eviction is  
processor-specific. A victim is also known as a cast out.  
Warm reset  
Watchpoint  
Also known as a core reset. Initializes the majority of the processor excluding the debug  
controller and debug logic. This type of reset is useful if you are using the debugging features  
of a processor.  
A watchpoint is a mechanism provided by debuggers to halt program execution when the data  
contained by a particular memory address is changed. Watchpoints are inserted by the  
programmer to enable inspection of register contents, memory locations, and variable values  
when memory is written to test that the program is operating correctly. Watchpoints are removed  
after the program is successfully tested. See also Breakpoint.  
Way  
See Cache way.  
See Write-back.  
A 32-bit data item.  
WB  
Word  
Word-invariant  
In a word-invariant system, the address of each byte of memory changes when switching  
between little-endian and big-endian operation, in such a way that the byte with address A in  
one endianness has address A EOR 3 in the other endianness. As a result, each aligned word of  
memory always consists of the same four bytes of memory in the same order, regardless of  
endianness. The change of endianness occurs because of the change to the byte addresses, not  
because the bytes are rearranged. The ARM architecture supports word-invariant systems in  
ARMv3 and later versions. When word-invariant support is selected, the behavior of load or  
store instructions that are given unaligned addresses is instruction-specific, and is in general not  
the expected behavior for an unaligned access.  
See also Byte-invariant.  
Write  
Writes are defined as operations that have the semantics of a store. That is, the ARM instructions  
SRS  
,
,
STM  
,
STRD  
,
STC  
,
STRT  
,
STRH STRB, STRBT, STREX, SWP, and SWPB, and the Thumb instructions STM,  
.
,
STR  
STRH  
,
STRB, and PUSH  
Write-back (WB)  
In a write-back cache, data is only written to main memory when it is forced out of the cache on  
line replacement following a cache miss. Otherwise, writes by the processor only update the  
cache. Also known as copyback.  
Write buffer  
A block of high-speed memory, arranged as a FIFO buffer, between the data cache and main  
memory, whose purpose is to optimize stores to main memory.  
Write completion  
The memory system indicates to the processor that a write has been completed at a point in the  
transaction where the memory system is able to guarantee that the effect of the write is visible  
to all processors in the system. This is not the case if the write is associated with a memory  
synchronization primitive, or is to a Device or Strongly Ordered region. In these cases the  
memory system might only indicate completion of the write when the access has affected the  
state of the target, unless it is impossible to distinguish between having the effect of the write  
visible and having the state of target updated. This stricter requirement for some types of  
memory ensures that any side-effects of the memory access can be guaranteed by the processor  
to have taken place. You can use this to prevent the starting of a subsequent operation in the  
program order until the side-effects are visible.  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
Glossary-14  
Glossary  
Write-through (WT)  
WT  
In a write-through cache, data is written to main memory at the same time as the cache is  
updated.  
See Write-through.  
Cache terminology diagram  
The figure below illustrates the following cache terminology:  
block address  
cache line  
cache set  
cache way  
index  
tag.  
Block address  
Tag  
Index  
Word  
Byte  
Cache way  
Cache set  
Cache line  
Word number  
Line number  
0
1
2
3
4
2
Tag  
5
6
7
m
1
0
3
n
0
2
1
Cache tag RAM  
Cache data RAM  
=
Hit  
Read data  
(way that corresponds)  
(way number)  
ARM DDI 0363E  
ID013010  
Copyright © 2009 ARM Limited. All rights reserved.  
Non-Confidential, Unrestricted Access  
Glossary-15  

Extech Instruments Computer Hardware Series 3000 User Manual
Electrolux U30280 35772G User Manual
Compaq Q1859 User Manual
ClearOne comm MAX Wireless 910 158 276 User Manual
Clarity C410 User Manual
Cannon Professional User Manual
Caldera SSK365NG US User Manual
BenQ Gaming LCD Monitor GW2255 User Manual
Belkin F9L1109V1 User Manual
AT T E5634B User Manual