AOC 7F SLK User Manual

AOC 7F-SLK  
AOC 7F-SLK  
17 inch Color Monitor  
User’s  
Manual  
by Envision Peripherals, Inc.  
Before operating your monitor, please read this  
manual thoroughly.  
AOC 7F-SLK  
1
v2_123102  
For Your Safety  
AOC 7F-SLK  
• The monitor is equipped with a three-pronged  
grounded plug, a plug with a third (grounding)  
pin. As a safety feature, this plug will only fit into  
a grounded power outlet. If your outlet does not  
accommodate the three-wire plug, have an  
electrician install the correct outlet, or use an  
adapter to ground the appliance safely. Do not  
defeat the safety purpose of the grounded plug.  
Precautions  
• Do not use the monitor near water, e.g. near a  
bathtub, washbowl, kitchen sink, laundry tub,  
swimming pool or in a wet basement.  
• Do not place the monitor on an unstable cart,  
stand, or table. If the monitor falls, it can injure a  
person and cause serious damage to the  
appliance. Use only a cart or stand  
• Unplug the unit during a lightning storm or when  
it will not be used for long periods of time.  
This will protect the monitor from damage due to  
power surges.  
recommended by the manufacturer or sold with  
the monitor. If you mount the monitor on a wall  
or shelf, use a mounting kit approved by the  
manufacturer and follow the kit instructions.  
• Do not overload power strips and extension  
cords. Overloading can result in fire or electric  
shock.  
• Slots and openings in the back and bottom of  
the cabinet are provided for ventilation. To  
ensure reliable operation of the monitor and to  
protect it from overheating, be sure these  
openings are not blocked or covered. Do not  
place the monitor on a bed, sofa, rug, or similar  
surface. Do not place the monitor near or over a  
radiator or heat register. Do not place the  
monitor in a bookcase or cabinet unless proper  
ventilation is provided.  
• Never push any object into the slot on the  
monitor cabinet. It could short circuit parts  
causing a fire or electric shock. Never spill  
liquids on the monitor.  
• Do not attempt to service the monitor yourself;  
opening or removing covers can expose you to  
dangerous voltage and other hazards. Please  
refer all servicing to qualified service personnel.  
• The monitor should be operated only with the  
type of power source indicated on the label. If  
you are not sure of the type of power supplied to  
your home, consult your dealer or local power  
company.  
To ensure satisfactory operation, use the  
monitor only with UL-listed computers which  
have appropriately configured receptacles  
marked between 100 - 240 V AC, Min. 3.5A.  
• Disconnect the power cord to stop the power  
supply to the monitor.  
• The wall socket should be installed near the  
equipment and should be easily accessible.  
AOC 7F-SLK  
3
v2_123102  
For Your Safety  
AOC 7F-SLK  
General Notes  
General Features:  
• Do not install the monitor near heat sources  
such as radiators or air ducts.  
• 17" (43.2 cm) Color Monitor  
• Crisp, Clear Display for Windows  
• Do not place monitor in direct sunlight or in  
areas with excessive dust, mechanical vibration  
or shock.  
• Supports Resolutions up to 1280 x 1024 pixels  
@60Hz  
• EPA ENERGY STAR®  
• Save the original shipping carton and packing  
materials in case you need to ship your monitor.  
Be sure to repackage your monitor as it was  
originally packed at the factory.  
• Periodically clean your monitor with a soft cloth.  
Stubborn stains may be removed with a cloth  
lightly dampened with a mild detergent solution.  
Never use strong solvents such as thinners,  
benzene, or abrasive cleaners, since these  
will damage the cabinet. Always unplug the  
monitor before cleaning it.  
Package Contents  
The box that your monitor was shipped in should  
have included the following items:  
1. 7F-SLK Color Monitor  
2. Power Cord  
3. Quick Start Guide  
4. Booklet  
Using the Right Power Cord  
(containing Warranty and Safety information)  
The supplied power cord is a NEMA 5-15 style  
plug. It is UL-listed and CSA labeled for  
125 volts AC.  
If the monitor will be connected to your computer’s  
power outlet, use a minimum No. 18 AWG, type  
SJT or SVT three conductors cord with one end  
terminating with a male grounded plug, rated 10A,  
250V, CEE-22. The other end must terminate with  
a molded-on type connector body, rated 10A,  
250V, having standard CEE-22 female  
configuration.  
AOC 7F-SLK  
4
v2_123102  
Before You Operate the Monitor  
AOC 7F-SLK  
Installing & Removing the Base  
AOC 7F-SLK  
5
v2_123102  
Before You Operate the Monitor AOC 7F-SLK  
Connecting the Wires Using the Power Cord Supplied  
1. Connect the built-in video cable into the 15-pin  
connector on the back of your computer and  
tighten the two screws.  
Caution: Make sure the power cord is the correct  
type that is required in your area. This monitor  
has a universal power supply that allows  
operation in either 100/120V AC or 220/240V AC  
voltage areas (no user adjustment is required).  
2. Connect the power cord into your monitor's  
power input socket.  
If the AC outlet is not grounded (with three  
holes), install the proper grounding adapter (not  
supplied).  
3. Plug the other end of the power cord into a  
grounded AC outlet or UL-approved power strip.  
AOC 7F-SLK  
v2_123102  
6
Before You Operate the Monitor AOC 7F-SLK  
Connecting the Wires Using An Optional Power Cord (Not Supplied)  
The power cord supplied with your monitor can  
only be connected to a grounded electrical wall  
socket or power strip.  
Follow these steps:  
1. Connect the built-in video cable into the 15-pin  
connector on the back of your computer and  
tighten the two screws.  
If you wish to connect your monitor to a power  
supply using the power input socket on the back of  
your computer, you must purchase a power cord  
with CEE-22 terminated connectors (see  
illustration above).  
2. Connect the power cord into your monitor's  
power input socket.  
3. Plug the other end of the power cord into the  
power output socket on your PC.  
AOC 7F-SLK  
v2_123102  
7
Operating Instructions  
AOC 7F-SLK  
Front Panel Buttons  
Shuttle Knob: Press this knob to open the  
OSD window or select a highlighted function.  
Rotate this knob to switch functions or adjust  
settings.  
Power: Press this button to put the monitor  
into Off mode. The power indicator will turn  
orange. Press and hold this button again to  
restore the monitor to normal operation  
mode.  
Power Indicator: A green light indicates that  
the monitor is on. An orange light indicates  
that the monitor is in Off mode.  
On-screen Display (OSD): Press the  
Shuttle Knob to open the OSD window  
and adjust settings on your monitor.  
Note: This monitor automatically turns on  
when it is plugged into an AC outlet.  
(See next page.)  
v2_123102  
AOC 7F-SLK  
8
Operating Instructions  
AOC 7F-SLK  
Adjusting the OSD Settings  
1. Press the Shuttle Knob to open the OSD  
5. To save and exit, select the exit function or  
leave the monitor alone for 10 seconds. If you  
want to adjust any other function, repeat steps  
2-4.  
window.  
2. Rotate the Shuttle Knob until the desired  
function is highlighted.  
Note: When the OSD window is open, the input  
signal timing settings appear at the top.  
H: stands for horizontal frequency and  
V: stands for vertical frequency.  
3. Press the Shuttle Knob again to open the  
function’s window.  
4. Rotate the Shuttle Knob to change the settings  
of the function.  
AOC 7F-SLK  
v2_123102  
9
Operating Instructions  
AOC 7F-SLK  
Plug & Play DDC1/2B Feature  
Windows INF Driver File  
This monitor is equipped with VESA DDC1/2B  
capabilities according to the VESA DDC  
STANDARD. It allows the monitor to inform the  
host system of its identity and, depending on the  
level of DDC used, communicate additional  
information about its display capabilities. The  
communication channel is defined in two levels,  
DDC1 and DDC2B.  
Most computers will automatically configure your  
monitor to work with your computer. For optimal  
viewing of your monitor, download the AOC  
monitor driver.  
Follow these steps:  
2. Click on SUPPORT to open the drivers web  
page.  
The DDC1 is a unidirectional data channel from the  
display to the host that continuously transmits  
EDID information. The DDC2B is a bidirectional  
data channel based on the I²C protocol. The host  
can request EDID information over the DDC2B.  
3. Follow the directions on the web page to  
download and install the driver on your  
computer.  
to directly access the driver web page.  
AOC 7F-SLK  
10  
v2_123102  
Technical Support (FAQ)  
AOC 7F-SLK  
Problem  
Possible Solution  
Power LED is not ON • Make sure the power cord is properly connected to a grounded power outlet  
and to the monitor.  
No Plug & Play  
• Confirm that your computer is Plug & Play compatible.  
• Confirm that your video card is Plug & Play compatible.  
• Inspect the video cable and make sure that none of the pins are bent.  
• Make sure the AOC monitor drivers are installed  
(AOC monitor drivers are available at: www.aocmonitor.com)  
Picture is fuzzy  
• Adjust the Contrast and Brightness settings.  
Picture bounces or a  
wave pattern is  
• Move electrical devices away from the monitor. They may be causing electrical  
interference.  
present in the picture  
Power LED is ON  
(green or orange light  
is ON) but there is no  
video or picture.  
• Press a key on the keyboard or wiggle the mouse to re-activate the monitor.  
• Make sure the video cable is properly connected to the computer.  
• Inspect the video cable and make sure none of the pins are bent.  
• Make sure your computer is operating correctly by pressing the CAPS LOCK  
key and observing whether the CAPS LOCK light turns ON or OFF.  
Missing one of the  
primary colors (RED,  
GREEN, or BLUE)  
• Inspect the video cable and make sure that none of the pins are bent.  
• Make sure the video cable is properly connected to the computer.  
Screen image is not  
centered or sized  
properly  
• Adjust the Horizontal, Vertical or Zoom settings in the OSD window.  
• Adjust the User Color setting in the OSD window.  
Picture has color  
defects (white doesn’t  
look white)  
AOC 7F-SLK  
11  
v2_123102  
Appendix  
AOC 7F-SLK  
Specifications  
Input  
Video  
Red, Green, Blue  
Analog Interface  
CRT  
Size  
17.0" (43.2 cm)  
11.4” (29 mm) neck  
Separate  
Sync.  
H/V TTL  
0.25mm(D),  
0.21mm(H) dot  
pitch  
H/V Sync.  
Positive/Negative  
H-Frequency 30 kHz - 72 kHz  
V-Frequency 50 Hz -130 Hz  
90 degree  
deflection  
Input  
Analog:  
Video  
Signal  
0.7 Vpp,  
75 OHM, Positive  
Viewable image size  
Preset Display area  
Dot Clock  
16.0” (40.6 cm)  
diagonal  
Power Source  
Universal AC  
100 - 240 V  
50/60 Hz  
11.8” (300 mm) X  
9.1” (230 mm)  
110 MHz  
Factory Preset Mode  
6
User Programmable Mode 10  
Maximum Resolution  
Plug & Play  
1280 x 1024 pixels  
EPA ENERGY STAR®  
Yes  
VESA DDC1/2B  
TM  
Power Consumption  
(Maximum)  
90 Watts  
Regulatory  
Compliance  
UL, CSA, FDA,  
FCC, TÜV/GS,  
MPRII  
AOC 7F-SLK  
12  
v2_123102  
Appendix  
AOC 7F-SLK  
Specifications (continued)  
Environmental  
Considerations  
Operating Temp:  
32° to 104°F  
(0° to 40°C) ambient  
Operating Humidity:  
10% to 85% relative,  
non-condensing  
Signal Cable  
Attached Mini D-sub  
15 Male  
Optimal Viewing Mode: 1024 x 768 x 85 Hz  
AOC 7F-SLK  
13  
v2_123102  
Appendix  
AOC 7F-SLK  
Factory Preset Timing Table  
Resolution  
(in pixels)  
Horizontal  
Frequency  
Vertical  
Frequency  
Standard  
VGA  
720 × 400  
640 × 480  
640 × 480  
800 × 600  
1024 × 768  
1280 × 1024  
31.5 KHz  
31.5 KHz  
43.3 KHz  
53.7 KHz  
68.7 KHz  
64.0 KHz  
70 Hz  
60 Hz  
85 Hz  
85 Hz  
85 Hz  
60 Hz  
VESA / 85  
VESA / 60  
AOC 7F-SLK  
14  
v2_123102  
Appendix  
AOC 7F-SLK  
Connector Pin Assignment  
Pin Number  
Description  
Pin Number  
Description  
1
2
3
4
5
6
7
8
Red  
9
NC  
Ground  
Green  
10  
11  
12  
13  
14  
15  
*
Blue  
Monitor Ground  
DDC-Serial Data  
H-Sync  
Ground  
Ground  
R-Ground  
G-Ground  
B-Ground  
V-Sync / *V-Clk  
DDC-Serial Clock  
For DDC  
AOC 7F-SLK  
15  
v2_123102  
Limited 3-Year Warranty  
AOC 7F-SLK  
This is a warranty statement for AOC color  
monitors including those sold within North America  
as specified.  
• Excessive or inadequate heating or air  
conditioning or electrical power failures, surges,  
or other irregularities. This three-year limited  
warranty does not cover any of the product's  
firmware or hardware that you or any third party  
have modified or altered; you bear the sole  
responsibility and liability for any such  
modification or alteration.  
Envision Peripherals, Inc. (EPI) warrants this  
product to be free from defects in material and  
workmanship for a period of three (3) years after  
the original date of consumer purchase. During this  
period, EPI will, at its option, either repair the  
defective product with new or rebuilt parts, or  
replace it with a new or rebuilt product at no charge  
except as stated below*. The parts or product that  
are replaced become the property of EPI.  
All express and implied warranties for the product  
(including the warranties of merchantability and  
fitness for a particular purpose) are limited in  
duration to a period of three (3) years for parts and  
labor from the original date of consumer purchase.  
No warranties (either expressed or implied) apply  
after this period. In the United States, some states  
do not allow limitations on how long an implied  
warranty lasts. Therefore, the above limitations  
may not apply to you.  
* This limited warranty does not cover any losses  
or damages that occur as a result of:  
• Shipping or improper installation or  
maintenance  
• Misuse  
• Neglect  
EPI’s obligations and your remedies hereunder are  
solely and exclusively as stated here. EPI’s liability,  
whether based on contract, tort, warranty, strict  
liability, or other theory, shall not exceed the price  
of the individual unit whose defect or damage is the  
basis of the claim. In no event shall EPI be liable  
for any loss of profits, loss of use or facilities or  
equipment or other indirect, incidental, or  
• Any cause other than ordinary commercial or  
industrial application  
• Adjustment by non-authorized source  
• Repair, modification, or installation of options or  
parts by anyone other than an EPI Authorized  
Service Center  
consequential damage. In the United States, some  
states do not allow the exclusion or limitation of  
incidental or consequential damages. Therefore,  
the above limitations may not apply to you.  
Improper environment  
AOC 7F-SLK  
16  
v2_123102  
Warranty (continued)  
AOC 7F-SLK  
Although this limited warranty gives you specific  
EPI is not responsible for damage to inbound  
legal rights, you may have other rights which may  
vary from state to state.  
products that were not properly packaged.  
EPI will pay the return shipment charges within one  
of the countries specified within this warranty  
statement. EPI is not responsible for any costs  
associated with the transportation of products  
across international borders. This includes the  
international borders of the countries within this  
warranty statements.  
In the United States of America, this limited  
warranty is only valid for products purchased in the  
Continental United States, Alaska, and Hawaii.  
Outside the United States, this limited warranty is  
only valid for products purchased in Canada.  
In the United States, to obtain service under this  
limited warranty:  
1. Call EPI’s Customer Service, RMA Department  
at the toll free number (888) 662-9888 for the  
nearest Authorized Service Center located in  
your area.  
© 2002 Envision Peripherals, Inc.  
2. Ask for a Return Merchandise Authorization  
(RMA) number.  
3. Deliver the product freight pre-paid to the EPI  
Authorized Service Center.  
If you cannot deliver the product in person:  
Pack it in its original shipping container  
(or equivalent)  
Put the RMA number on the shipping carton  
• Insure it (or assume the risk of loss / damage  
during shipment)  
• Pay one-way shipping charge  
AOC 7F-SLK  
17  
v2_123102  

GE Monogram ZET837WBWW User Manual
FUNAI Durabrand CR130DR8 User Manual
Electrolux CSIG 417 User Manual
DeLonghi Cooktop DE30WGB User Manual
Dell Computer Monitor SX2210T User Manual
Dacor Cooktop DRT366S User Manual
Cleveland Range Convotherm Combination Oven Steamer Gas 20 20 User Manual
Black Box Computer Hardware LPB1305A User Manual
AT T DECT 6 0 EL52251 User Manual
AG Neovo Neovo E 19 User Manual