Operation/Reference Guide
MVP-7500/8400
MVP-7500/8400 Modero® ViewPoint® Wireless Touch Panels
MVP-BP Power Pack
NXA-CFSP Compact Flash Card
Last Revised: 6/13/2008
Touch Panels & Accessories
FCC Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received; including interference
that may cause undesired operation.
Federal Communications Commission (FCC)
Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy, and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
FCC RF Radiation Exposure Statement
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This
equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed an operated with a minimum distance of 20 centimeters between the radiator and your body.
Table of Contents
Table of Contents
MVP-BP Power Pack ...........................................................................................5
MVP-BP Specifications ................................................................................................... 5
NXA-CFSP Compact Flash ..................................................................................7
Compact Flash Card - Security.................................................................................. 7
Accessing the MVP’s Internal Components..................................................................... 7
Removing the Installed Card........................................................................................... 8
Installing the Compact Flash Upgrade Card.................................................................... 8
Wireless Interface Cards ...................................................................................11
Specifications ............................................................................................................. 13
Firmware Requirements ................................................................................................ 15
Access the MVP’s Internal Components........................................................................ 15
Removing the Installed Card......................................................................................... 15
Preparing the MVP’s Rear Housing ............................................................................... 15
Installing the NXA-WC80211GCF ................................................................................. 16
Closing and Securing the MVP Enclosure...................................................................... 17
Configuring Communications ...........................................................................19
Accessing the Setup and Protected Setup Pages.......................................................... 19
Setting the Panel’s Device Number .............................................................................. 20
Wireless Settings Page - Wireless Access Overview ............................................... 20
Hot Swapping ............................................................................................................... 20
Step 1: Configure the Panel’s Wireless IP Settings................................................. 21
Wireless communication using a DHCP Address........................................................... 21
Wireless communication using a Static IP Address........................................................ 22
i
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Table of Contents
Using the Site Survey tool............................................................................................. 22
Automatically set SSID .................................................................................................. 27
Manually set SSID.......................................................................................................... 28
Prepare your PC for USB communication with the panel .............................................. 32
Configure the panel for USB communication ................................................................ 32
Configure a Virtual NetLinx Master using NetLinx Studio............................................. 33
Ethernet ........................................................................................................................ 35
Master Connection to a Virtual Master via Ethernet ..................................................... 35
Using G4 Web Control to Interact with a G4 Panel ................................................ 38
Using your NetLinx Master to control the G4 panel ............................................... 40
Upgrading MVP Firmware ................................................................................43
Step 1: Configure the panel for a USB Connection Type .............................................. 44
Step 2: Prepare Studio for communication via the USB port ........................................ 44
Step 2: Upgrade the Docking Station firmware via USB ............................................... 48
Setup Pages............................................................................................................ 51
Navigation Buttons........................................................................................................ 53
Project Information Page............................................................................................... 53
Panel Information Page ................................................................................................. 55
Time & Date Setup Page............................................................................................... 56
Audio Adjustments/Volume Page.................................................................................. 57
WAV files - Supported sample rates.............................................................................. 58
Batteries Page............................................................................................................... 59
Protected Setup Navigation Buttons............................................................................. 62
G4 Web Control Page ................................................................................................... 63
Password Setup Page.................................................................................................... 64
Calibration Page............................................................................................................ 65
Wireless Settings Page.................................................................................................. 66
ii
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Table of Contents
Wireless Security Page.................................................................................................. 69
Open (Clear Text) Settings............................................................................................ 70
Static WEP Settings....................................................................................................... 71
WPA-PSK Settings......................................................................................................... 73
EAP-LEAP Settings........................................................................................................ 74
EAP-FAST Settings........................................................................................................ 76
EAP-PEAP Settings........................................................................................................ 78
EAP-TTLS Settings......................................................................................................... 80
EAP-TLS Settings........................................................................................................... 82
Client certificate configuration...................................................................................... 83
System Settings Page.................................................................................................... 85
Programming ....................................................................................................89
Page Commands..................................................................................................... 89
RGB triplets and names for basic 88 colors .................................................................. 95
Font styles and ID numbers........................................................................................... 97
Border styles and Programming numbers..................................................................... 98
Miscellaneous MVP Strings back to the Master .......................................................... 119
MVP Panel Lock Passcode commands......................................................................... 119
Text Effects Names............................................................................................... 120
Embedded codes.................................................................................................. 135
Panel Setup Commands........................................................................................ 136
Intercom Commands............................................................................................. 139
Panel Calibration ............................................................................................141
Testing your Calibration.............................................................................................. 142
If Calibration Is Not Working ...................................................................................... 143
Appendix A: Text Formatting .........................................................................145
Text Formatting Codes for Bargraphs/Joysticks................................................... 145
Input mask character types ......................................................................................... 146
iii
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Table of Contents
Input mask ranges ....................................................................................................... 147
Input mask next field characters.................................................................................. 147
Input mask operations................................................................................................. 147
Input mask literals ....................................................................................................... 147
Input mask output examples....................................................................................... 148
Special escape sequences ........................................................................................... 149
Appendix B - Wireless Technology .................................................................151
EAP characteristics ...................................................................................................... 155
EAP communication overview ..................................................................................... 156
Step 1: Setup the Panel and PC for USB Communication............................................ 157
Step 2: Confirm the Installation of the USB Driver on the PC ..................................... 158
Panel Doesn’t Respond To Touches ............................................................................ 163
Batteries Will Not Hold Or Take A Charge.................................................................. 163
Modero Panel Isn’t Appearing In The Online Tree Tab ............................................... 164
MVP Can’t Obtain a DHCP Address ............................................................................ 164
My WEP Doesn’t Seem To Be Working....................................................................... 164
Can’t Connect To a NetLinx Master ............................................................................ 164
Only One Modero Panel In My System Shows Up....................................................... 165
iv
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
MVP Modero Viewpoint Wireless Touch Panels
MVP Modero Viewpoint Wireless Touch
Panels
Overview
802.11-based wireless handheld G4 touch panels, pre-installed with an 802.11 Wi-Fi Interface Card to
communicate with a NetLinx Master via a standard 802.11b/g Wireless Access Point.
MVP-7500
(FG5965-01)
MVP-8400
(FG5965-02)
FIG. 1 MVP-7500 and MVP-8400 Touch Panels
ꢀ
ꢀ
Previous 802.11b versions of MVP panels are field upgradeable to 802.11g communication
via the installation of the NXA-WC8011GCF Wi-Fi Card Kit (FG2255-07).
MVP panels feature nine programmable external pushbuttons and two programmable LEDs,
and support AMX G4 graphics technology, making them compatible with AMX’s TPDesign4
Touch Panel Design program.
ꢀ
ꢀ
MVP panels utilize two IR frequencies (38 KHz and 455 KHz) as well as 2 additional user-
defined IR libraries, on 4 IR ports.
MVP panels feature programmable firmware that can be upgraded via either the wireless
interface card or the mini-USB port. MVP panels utilize unique firmware kit files: the MVP-
7500 can be upgraded via the "5965-01.kit" file, while the MVP-8400 can be upgraded via the
"5965-02.kit" file.
ꢀ
ꢀ
MVP panels support AMX Computer Control, which enables remote viewing and control of
any networked computer directly from the panel. This gives the user the ability to launch
digital music from a PC, cruise the Internet, check and respond to E-mail, open software files,
and launch applications.
MVP panels come equipped with a battery and power supply (see specifications).
Optional AMX accessory solutions for the MVPs include
ꢀ
ꢀ
ꢀ
MVP-TDS Table Top Docking Station (see the MVP-TDS Table Top Docking Station
Operation/Reference Guide for details).
MVP-WDS Wall/Flush Mount Docking Station-Black/Silver (see the MVP-WDS Wall
Docking Station Operation/Reference Guide for details).
MVP-KS Kickstand (see the MVP-KS Kickstand Operation/Reference Guide for details).
1
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
MVP Modero Viewpoint Wireless Touch Panels
MVP Specifications
ꢀ
The MVP-7500 (FG5965-01) utilizes a 7.5" Color Passive LCD to display a 640 x 480 pixel
image with 4096 colors.
ꢀ The MVP-8400 panel (FG5965-02) utilizes an 8.4" Color Active LCD to display an 800 x 600
pixel resolution using 256K colors.
Mini-USB connector
programmable
programmable
status LED
Stylus LED
programmable
pushbuttons
(joystick
programmable
pushbuttons
configuration)
Stylus
(fits within slot
on side panel)
Microphone
MVP-8400 only
Speaker (right)
MVP-8400 only
Speaker (left)
MVP-8400 only
PWR connector
Docking station interface connector
FIG. 2 MVP Touch Panels
MVP Specifications
Models:
• MVP-7500
• MVP-8400
Dimensions (HWD):
Power Requirements:
• 7.09" x 10.47" x 1.47" (18.00 cm x 26.60 cm x 3.73 cm)
Without Charging:
MVP-7500:
• Constant current draw: 1.0 A @ 12 VDC
• Startup current draw: 1.5 A @ 12 VDC
MVP-8400:
• Constant current draw: 1.2 A @ 12 VDC
• Startup current draw: 1.8 A @ 12 VDC
While Charging:
MVP-7500:
• Constant current draw: 3.0 A @ 12 VDC
• Startup current draw: 3.6 A @ 12 VDC
MVP-8400:
• Constant current draw: 3.2 A @ 12 VDC
• Startup current draw: 3.8 A @ 12 VDC
• If MVP panel is mounted onto a TDS or WDS, add 0.1 A to the above figures.
• ON: Panel is fully functional.
Power Modes:
• STANDBY: Panel uses low power, the LCD/backlight is shutdown, LEDs still
function. Panel resumes the ON mode in ~ 1 second.
• OFF: On-board programs not running, touch screen still powered, LED not
functional. Panel resumes the ON mode in ~ 30 seconds.
Battery Duration:
(per battery)
• Four hours of normal use (25% On state, 25% Standby, and 50% Off).
• Two hours of continuous use.
2
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
MVP Modero Viewpoint Wireless Touch Panels
MVP Specifications
Memory (factory default):
• 64 MB SDRAM
• 64 MB Compact Flash (upgradeable to 1 GB - factory programmed)
1.85 lbs (0.84 kg)
Weight:
• with 1 battery: 2.25 lbs (1.02 kg)
• with 2 batteries: 2.65 lbs (1.20 kg)
MVP-7500 LCD
Specifications:
• Aspect ratio: 4 x 3
• Brightness (luminance): 120 cd/m2
• Channel transparency: 8-bit Alpha blending
• Contrast ratio: 20:1
• Display colors: 4096 colors (12-bit color depth)
• Dot/pixel pitch: 0.23 mm
• Panel type: TFT Color Passive-Matrix
• Screen resolution: 640 x 480 pixels (HV) @ 60 Hz frame frequency
• Viewing angles (vertical): + 17° / - 17° (from center)
• Aspect ratio: 4 x 3
• Brightness (luminance): 180 cd/m2
• Channel transparency: 8-bit Alpha blending
• Contrast ratio: 350:1
MVP-8400 LCD
Specifications:
• Display colors: 256K colors (18-bit color depth)
• Dot/pixel pitch: 0.21 mm
• Panel type: TFT Color Active-Matrix
• Screen resolution: 800 x 600 pixels (HV) @ 60 Hz frame frequency
• Viewing angles (vertical): + 60° / - 40° (from center)
External Components:
Docking station interface
connector:
Metallic strip connector located on the bottom panel provides communication
and power between the panel and the optional docking stations.
LEDs:
Two sets of NetLinx programmable LEDs (supporting On, Off, and Blink).
Default blink patterns:
- Stylus LED: Blink = Batteries charging, On = Batteries charged.
- Front panel LED: Blink = Panel booting, On = Panel operating properly.
Mini-USB connector:
Power connector:
Stylus slot:
5-pin mini-USB connector for programming, firmware update, and file transfer.
• 2.1mm barrel-style power jack, for use with the included PS4.4 power supply.
• Illuminated slot where the included stylus is stored, located on the left side of
the MVP.
External Buttons:
• Nine programmable pushbuttons (four located on the left of the LCD and five
located on the right in a joystick configuration).
Internal Components:
Wireless Interface card:
Provides 802.11 (CF Type I) wireless connectivity between the panel and a
Wireless Access Point (such as the NXA-WAP200G).
IR Emitters:
Transmit IR over 20 feet (6.10 m).
Internal buzzer:
Emits a Piezo electric tone (MVP-7500 only).
Two speakers for stereo output (MVP-8400 only).
For use with the intercom feature (MVP-8400 only).
Houses up to 2 MVP-BP Power Packs.
Internal speakers:
Internal microphone
Battery compartment:
3
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
MVP Modero Viewpoint Wireless Touch Panels
MVP Specifications
Button Assignments:
Button assignments can only be adjusted in TPD4 and not on the panels.
• Button channel range: 1 - 4000 button push and feedback (per address port)
• Button variable text range: 1 - 4000 (per address port)
• Button states range: 1 - 256 (General Button; 1 = Off State, 2 = On State)
• Level range: 1 - 600 (default level value 0-255, can be set up to 1-65535)
• Address port range: 1 - 100
Operating / Storage
Environment:
• Operating Temperature: 0° C (32° F) to 40° C (104° F)
• Operating Humidity: 20% - 85% RH
• Storage Temperature: -20° C (-4° F) to 60° C (140° F)
• Storage Humidity: 5% - 85% RH
Certifications:
• FCC Part 15 Class B and CE
Included Accessories:
• MVP-BP Power Pack (FG5965-20): 1 with MVP-7500, 2 with MVP-8400
• 80211xCF Wireless Interface Compact Flash card (Type 1) - pre-installed
• PS4.4 Power Supply (FG423-44)
• Stylus
Other AMX Equipment:
• CB-MVPWDS Conduit Box (FG037-10)
• CC-USB (Type A) to Mini-B 5-Wire programming cable (FG10-5965)
• MVP-BP Power Pack (additional/spare) (FG5965-20)
• MVP-KS Kickstand (FG5965-12)
• MVP-STYLUS three pack (FG5965-30)
• MVP-TDS Table Top Docking Station (FG5965-10)
• MVP-WDS Wall/Flush Mount Docking Station:
Black (FG5965-11) / Silver (FG5965-21)
• MVP-WDS-SK Silver Conversion Kit for MVP-WDS (FG5965-22)
• NXA-WC80211GCF 802.11g Wireless Compact Flash Card Upgrade Kit
(FG2255-07)
• Upgrade Compact Flash (factory programmed with firmware):
MVP-7500:
NXA-75CF128M - 128 MB compact flash card (FG2116-55)
NXA-75CF256M - 256 MB compact flash card (FG2116-56)
NXA-75CF512M - 512 MB compact flash card (FG2116-57)
NXA-75CF1GB - 1 GB compact flash card (FG2116-58)
MVP-8400:
NXA-84CF128M - 128 MB compact flash card (FG2116-50)
NXA-84CF256M - 256 MB compact flash card (FG2116-51)
NXA-84CF512M - 512 MB compact flash card (FG2116-52)
NXA-84CF1GB - 1 GB compact flash card (FG2116-53)
4
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
MVP-BP Power Pack
MVP-BP Power Pack
Overview
The MVP-BP Power Pack (FG5965-20) is a rechargeable Lithium-Ion battery used to provide power to
the MVP touch panels.
ꢀ
ꢀ
One MVP-BP is included with each MVP-7500 touch panel.
Two MVP-BPs are included with each MVP-8400 touch panel.
FIG. 3 MVP-BP Power Pack
MVP-BPs can be charged with either a Table Top Docking Station (MVP-TDS), Wall/Flush Mount
Docking Station (MVP-WDS), or MVP panel itself. Extra MVP-BP Power Packs can be purchased
separately.
MVP-BP Specifications
MVP-BP Specifications
Dimensions (HWD):
Power (Voltage):
Weight:
0.48" x 1.52" x 8.65" (1.23 cm x 3.86 cm x 21.97 cm)
7.2 Volts (nominal)
0.40 lbs (0.18 kg)
3600mAh
Charge Capacity:
Operating/Storage Environments: • Operating Temperature: 0° C (32° F) to 40° C (104° F)
• Operating Humidity: 20% - 85% RH
• Storage Temperature: -20° C (-4° F) to 60° C (140° F)
• Storage Humidity: 5% - 85% RH
Installing MVP-BP Batteries
1. Disconnect any cables, and place the MVP face down to expose the battery compartment.
2. Press down on the traction grooves to slide the battery compartment cover (away from the metal
plate), to open the battery compartment.
3. Insert the MVP-BP(s) so that the connector makes contact with the battery pins at the end of the
battery slot as shown in FIG. 4.
5
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
MVP-BP Power Pack
Battery Compartment Cover
Alignment Guide hole openings
Traction Grooves
Battery connector
Battery pins
Battery
Removal
Straps
Battery slot 2
Battery slot 1
FIG. 4 Installing MVP-BP batteries into the MVP battery slots
If you are only using one battery, use Battery Slot #1.
4. To replace the battery compartment cover, use the alignment guide holes to align the cover with the
edges of the battery compartment, and slide it back into place until it snaps shut.
6
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
NXA-CFSP Compact Flash
NXA-CFSP Compact Flash
Overview
Every MVP panel is shipped with a 64 MB Compact Flash card.
Compact Flash Card - Security
All security user names and passwords (for the docking station) are stored in the Compact Flash card.
After installing the Compact Flash card upgrade, all security user names and passwords need to be re-
entered to enable security. For this reason, it is recommended that you upgrade the card prior to setting
up the security information for the docking station.
The NXA-CFSP Compact Flash card is factory programmed with panel firmware and can be upgraded
up to 1GB:
Optional Compact Flash Upgrades
• NXA-CFSP128M - 128 MB Compact Flash card (FG2116-36)
• NXA-CFSP256M - 256 MB Compact Flash card (FG2116-37)
• NXA-CFSP512M - 512 MB Compact Flash card (FG2116-38)
• NXA-CFSP1G - 1 GB Compact Flash card
(FG2116-39)
Installing the NXA-CFSP Compact Flash Card
Batteries should be removed prior to upgrading the Compact Flash card.
Accessing the MVP’s Internal Components
1. Remove all connectors, remove power and remove batteries.
3. Grasp the bottom rim of the rear housing just above the MVP interface connector, and carefully pull
the bottom rim away from the IR Emitter and up, to expose the internal components.
7
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
NXA-CFSP Compact Flash
Battery Compartment cover
Housing screws
B
Rear outer housing
Bottom rim of outer
housing
Trim fits inside
the grooves around
the edges of the panel
A
Circuit board
housing
attachment
locations (4)
Panel
FIG. 5 Removing the MVP enclosure (housing)
Removing the Installed Card
1. Discharge any static electricity from your body by touching a grounded metal object and then locate
2. Place the circuit board on a flat level surface so that the IR Emitters are pointing away from you
(FIG. 6).
3. Insert the tip of a grounded flat-head screwdriver into one of the card removal grooves (located on
either side of the existing card), and gently pry it out of the slot (FIG. 7). Repeat this process on the
opposite card removal groove. This alternating action causes the card to "wiggle" away from the
on-board connector pins.
4. Slip your finger into the gap between the card and the circuit board and firmly grab the card by its
sides, then carefully pull it up and out of the slot. An angular removal of the card is required because
one of the housing’s latch attachments blocks the slot opening.
use care when pulling up on the card.
Installing the Compact Flash Upgrade Card
1. Discharge any static electricity from your body by touching a grounded metal object and then locate
8
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
NXA-CFSP Compact Flash
Internal circuit board
(top view - detail)
Card removal grooves
IR Emitters
Compact Flash
card
A
B
Wireless Interface
card
FIG. 6 Location and orientation of the Compact Flash cards (both MVP panels)
2. Place the circuit board on a flat level surface so that the IR Emitters are pointing away from you
3. Insert the tip of a grounded flat-head screwdriver into one of the card removal grooves (located on
either side of the existing Compact Flash card), and gently pry it out of the slot (FIG. 7). Repeat this
process on the opposite card removal groove. This alternating action causes the pre-existing card to
"wiggle" away from the on-board connector pins.
4. Slip your finger into the opening (between the connector pins and the card resulting from step 3)
and push the card out.
5. Finish the process by firmly gripping the exposed sides of the card and pulling it out (FIG. 7). USE
CARE WHEN HANDLING THE CARD.
Card removal
grooves
On-board Compact
Flash connector (with pins)
Insert with arrow
facing towards the pins
Connector opening
FIG. 7 Removing/installing a Compact Flash Memory card
completely inside the card and securely attached to the pin sockets.
Any new Compact Flash card upgrade is detected by the panel only after the unit
cycles power.
9
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
NXA-CFSP Compact Flash
10
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Wireless Interface Cards
Wireless Interface Cards
802.11b Wireless Interface Card
MVP panels can connect to a wireless network using the 802.11b Wireless Interface Card (70-5965-02),
pre-installed in MVP touch panel models. The 802.11b Wireless Interface Card is a 2.4 GHz Direct
Sequence Spread Spectrum (DSSS) 802.11b 11M wireless PC card, with detachable antenna.
FIG. 8 802.11b Wireless Interface Card
The wireless interface card works with 802.11b/g Wireless Access Points, such as the NXA-WAP200G.
The NXA-WAP200G uses a default SSID of AMX.
Follow your particular WAP’s instruction manual for setup procedures.
Specifications
802.11b Wireless Interface Card Specifications
Dimensions (HWD):
Weight:
• 2.07" x 1.68" x 0.21" (52.56 mm x 42.80 mm x 5.57 mm)
• 13.61 grams (0.030 lbs)
Features:
• Wired Equivalent Privacy (WEP) 64-bit and 128-bit data encryption
• Diversity Antenna Connectors automatically select the best available signal
• Supports infrastructure (communications to wired networks via Access Points),
and roaming (standard IEEE 802.11b compliant)
Antenna:
• 2, Ceramic (Diversity Supported)
• Compact Flash Type I
• Interoperable with Wi-Fi (WECA) certified products
• Power / Link activity
Host Interface:
Interoperability:
LED Indicators:
Modulation:
• DSSS, DBSK, DQSK, CCK
• IEEE 802.11b
Network Standard:
Number of Channels:
Operating Voltage:
Operating Channels:
• 14
• 5 / 3.3 V
• 11 Channels (USA, Canada)
• 13 Channels (Europe)
• 14 Channels (Japan)
• 4 Channels (France)
Operating Environment: • Temperature: 0°C ~ 70°C (non-operating) and -15 ~ 80°C (storage)
• Humidity (non-condensing): 5% ~ 95% RH
11
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Wireless Interface Cards
802.11b Wireless Interface Card Specifications (Cont.)
Power Consumption:
• TX power consumption: < 265 mA
• RX power consumption: < 165 mA
• Sleep Mode: 2 mA - 15 mA
Radio Data Rate:
• 1Mbps, 2Mbps, 5.5Mbps, 11Mbps, Auto Rate
Receive Sensitivity:
• @PER < 8%
11 Mbps: -83 dBm (max)
5.5 Mbps: -86 dBm (max)
2 Mbps: -89 dBm (max)
1 Mbps: -92 dBm (max)
RF Output Power:
• 15 dBm +/- 1 dBm
• Channels 1 - 11 (North America)
• WEP 64,128 bit, WPA/TKIP
Security:
Wireless Restrictions:
• In R&TTE countries, such as France, the 802.11g frequency band is restricted to
2454 - 2483.5 MHz (2.4 - 2.4835 GHz) and a max power output of
100 mW EIRP outdoor.
Certifications:
• FCC (United States)
• IC (Canada)
• CE (Europe)
• TELEC (Japan)
The only time the wireless card should be removed is in case of failure or when
upgrading to the 802.11g Wi-Fi card.
NXA-WC80211GCF 802.11g Wireless Interface Card
Optionally, MVP panels can be upgraded with the field-installable 802.11g Wi-Fi card (FG2255-07),
purchased separately as a Wi-Fi Upgrade Kit.
PIFA antenna
FIG. 9 NXA-WC80211GCF 802.11g wireless card
The NXA-WC80211GCF is a 2.4 GHz Wi-Fi LAN CF Card which upgrades a Modero panel’s RF
capabilities from 802.11b to 802.11g. This card provides enhanced range and throughput, wireless
encryption and data security (WPA and WPA2 and WEP) in Compact Flash Type I form factor.
The NXA-WC80211GCF incorporates DSSS and OFDM radio technology and operates at ISM
frequency bands of 2.4 GHz, while providing data transfer speeds of up to 54Mbps.
Other features include:
ꢀ
ꢀ
Support for IEEE 802.11b and 802.11g
Supports Advanced Encryption Standard (AES) at 128-bit.
12
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Wireless Interface Cards
ꢀ
ꢀ
ꢀ
Supports authentication methods such as: EAP-FAST, EAP-LEAP, EAP-PEAP, EAP-TLS,
and EAP-TTLS
Supports Wired Equivalent Privacy (WEP) 64-bit and 128-bit data encryption (known to the
on-board firmware as Static WEP)
The NXA-WC80211GCF is backwards compatible with 802.11b networks.
To fully utilize wireless security features, this card must be used in tandem with the
latest Modero firmware upgrade available at www.amx.com.
This upgrade kit requires that pre-existing panels first be removed from their current location (tabletop or
wall docking station) before an installer can access the internal circuit boards and upgrade a pre-existing
802.11b wireless CF card.
MVP panels require the use of a cardboard cutout (Mounting Template) to properly position the metal
antenna plate onto the inner surface of the unit’s rear plastic housing. The procedures for upgrading a CF
card on an MVP is identical for both MVP-7500 and MVP-8400 panels.
Specifications
NXA-WC80211GCF Specifications
Dimensions (HWD):
Weight:
• 0.22" x 1.68" x 2.40" (5.6 mm x 42.80 mm x 61.0 mm)
• 19.50 grams (0.043 lbs)
Description:
• Wireless LAN Compact Flash Card with external PIFA antenna.
• Features enterprise-class security such as WPA and WPA2 security.
•
Antenna Type:
Bus Interface:
Certifications:
• External PIFA antenna (factory-installed)
• Compact Flash Type I
• FCC Part 15 Class B, CE, IC, TELEC, and Wi-Fi
Media Access Control
Techniques:
• Using 802.11b DSSS communication:
DBPSK @ 1 Mbps
DQPSK @ 2 Mbps
CCK @ 5.5 Mbps
• Using 802.11g OFDM communication:
BPSK @ 6 and 9 Mbps
QPSK @ 12 and 18 Mbps
16-QAM @ 24 and 36 Mbps
64-QAM @ 48 and 54 Mbps
Network Architecture:
Operating Channels:
• Infrastructure mode (Client-to-Access Point)
• Using 802.11b & g communication:
- 04: (Ch 10 - 13) - France
- 11: (Ch 1 - 11) - North America
- 13: (Ch 1 - 13) - Europe ETSI
- 13: (Ch 1 - 13) - Japan (802.11g)
- 14: (Ch 1 - 14) - Japan (802.11b)
Note: To alter the card’s default country code (North America), contact an AMX
Technical Support representative for detailed procedures and information.
13
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Wireless Interface Cards
NXA-WC80211GCF Specifications (Cont.)
Operating Environment: • Temperature: 0°C ~ 45°C (32°F to 113°F) (operating) and
-20°C ~ 70°C (-4°F to 158°F) (storage)
• Humidity: (non-condensing) 5% ~ 90% RH (operating) and
(non-condensing) 5% ~ 95% RH (storage)
Operating Voltage:
• 3.3V + 5% I/O supply voltage
Power Consumption:
• @ 802.11b communication:
- RX: 270 mA
- TX: 435 mA
- Standby: 240 mA
• @ 802.11g communication:
- RX: 270 mA
- TX: 460 mA
- Standby: 240 mA
Radio Data Rate:
• 802.11g compliant: 1, 2, 5.5, 11 (DSSS/CCK); 6, 9, 12, 18, 24, 36, 48, and 54
(OFDM) Mbps data rates
Radio Technology:
• Using 802.11b communication: DSSS (Direct Sequence Spread Spectrum)/CCK
(Complementary Code Keying)
• Using 802.11g communication: DSSS/CCK, OFDM (Orthogonal Frequency
Division Multiplexing
Receiver Sensitivity:
• Using 802.11b communication @ FER<8%:
1 Mbps: -94 dBm (max)
2 Mbps: -93 dBm (max)
5.5 Mbps: -92 dBm (max)
11 Mbps: -90 dBm (max)
• Using 802.11g communication @ PER <10%:
6 Mbps: -87 dBm (max)
9 Mbps: -86 dBm (max)
12 Mbps: -86 dBm (max)
18 Mbps: -84 dBm (max)
24 Mbps: -82 dBm (max)
36 Mbps: -78 dBm (max)
48 Mbps: -74 dBm (max)
54 Mbps: -72 dBm (max)
RF Frequency Ranges:
• Using 802.11b & g communication:
Europe ETSI: 2.412 ~ 2.472 GHz
France: 2.457 ~ 2.472 GHz
Japan (802.11b): 2.412 ~ 2.484 GHz
Japan (802.11g): 2.412 ~ 2.472 GHz
North America: 2.412 ~ 2.462 GHz
Standard Conformance: • IEEE 802.11b
• IEEE 802.11g
• IEEE 802.11e
• IEEE 802.11i
• Wi-Fi (WPA and WPA2)
Transmit Output Power: • 802.11b communication: 12 +-1 dBm (1, 2, 5.5, 11 Mbps)
• 802.11g communication: 12 +-1 dBm (6, 9, 12, 18, 24, 36, 48, and 54 Mbps)
Wireless LAN Security:
• EAP-FAST
• EAP-LEAP
• EAP-PEAP
• EAP-TLS
• EAP-TTLS
• WEP 64 & 128
• WPA-PSK
14
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Wireless Interface Cards
NXA-WC80211GCF Specifications (Cont.)
Touch Panel
• MVP-7500 (FG5965-01)
Compatibility:
• MVP-8400 (FG5965-02)
• NXD-CV10 (FG2259-02)
• NXT-CV10 (FG2259-01/03)
• NXD-CV7 (FG2258-02)
• NXT-CV7 (FG2258-01)
Included Accessories:
• Double-sided adhesive tape
• Mounting Template cutout (62-2255-04)
• NXA-WC80211GCF Quick Start Guide
• Two Alcohol cleaning pads
• Wireless CF card with wireless antenna
Installing the 802.11g Card and Antenna
Upgrading the cards on an MVP involves opening the panel enclosure, removing the existing card,
replacing it with the upgrade, and then closing the panel enclosure, as described below.
Firmware Requirements
The NXA-WC80211GCF requires panel firmware versions 5965-01(MVP-7500), and 5965-02 (MVP-
8400). This firmware supports backwards compatibility with 802.11b cards, and security protocols for
the NXA-WC80211GCF.
Before installing the NXA-WC80211GCF, upload the latest panel-specific kit file to your MVP (5965-
01.kit for the MVP-7500 and 5965-02.kit for the MVP-8400).
Access the MVP’s Internal Components
Removing the Installed Card
Preparing the MVP’s Rear Housing
1. Flip over the MVP’s rear housing so that the internal support structures are visible, and lay it
directly in front of the circuit board such that the battery compartment is furthest away from you.
This placement provides contact of both top rims (FIG. 10).
2. Use an alcohol pad (included) to clean both the rear housing’s inner surface (bottom right corner)
cleaned to provide good adhesion for the later installation of the antenna.
3. Place the included Mounting Template along the bottom right corner of the rear housing (FIG. 10).
Use the housing’s inner supports to position the template properly.
15
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Wireless Interface Cards
Mounting Template
clean
this
Inner supports
area
Wireless Card Slot
FIG. 10 Installing the Mounting Template
Installing the NXA-WC80211GCF
1. Grip the sides of the NXA-WC80211GCF and insert it into the slot opening at a downward angle
until the contact pins are securely attached to the pin sockets.
2. Carefully peel off one side of the included double-sided tape and adhere the adhesive side to the
surface of the antenna’s metal plate.
3. Align the double-sided tape to the surface of the terminal antenna’s metal plate, in order to later
secure the antenna within the pre-defined installation area outlined by the included Mounting
Template.
4. Locate the T-shaped opening on the left of the cutout and make sure the antenna wire is located
along the left side of the cutout (FIG. 4).
FIG. 11 Adhering the antenna plate to the MVP outer housing
16
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Wireless Interface Cards
5. Grip the antenna by its sides and carefully peel-off the remaining protective film on the double-
sided tape.
6. Align the antenna into the long vertical groove in the cutout and firmly adhere it to the inner surface
of the housing. Make sure the wire is threaded along the left side of the cutout, this helps in the
removal of the cutout.
7. With the antenna now securely attached to the MVP’s inner housing, remove the cutout by carefully
pulling up on the cutout and threading the antenna wire through the T-shaped opening.
Closing and Securing the MVP Enclosure
Once the card has been installed, close and re-secure the outer housing:
Emitters, insert the four outer housing latches into their corresponding attachment locations along
the top rim of the MVP panel (two on either side of the IR Emitters).
Outer housing latches (4)
B
A
4 Outer housing latch
attachment locations
FIG. 12 Outer housing latch attachment locations
3. While firmly holding the top rims together, gently press down on the bottom ridge of the outer
housing (at the latch locations) and verify that each housing latch fits within its corresponding
attachment location on the board. When done, complete the insertion of the remaining housing
latches.
4. Verify that the notches along the bottom of the plastic battery slot separator strip also fit into the
three provided alignment holes on the circuit board.
5. Firmly press down around the entire rim of the outer housing to snap the cover back into place.
Be careful not to pinch the antenna wire in the housing.
6. Use a grounded Phillips-head screwdriver to insert and re-secure the two housing screws removed in
Step 1.
7. Insert any available batteries back into the battery compartment.
17
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Wireless Interface Cards
8. Grab the battery cover and align it over the edges of the battery compartment. Apply downward
pressure to the traction grooves on the Battery Compartment cover and slide it back towards the
metal plate to reinstall the cover.
Once the wireless CF card has been installed, be careful not to disconnect or
damage the antenna when subsequentally opening the MVP’s housing.
18
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Configuring Communications
Configuring Communications
Communication between the MVP and the Master consists of using either Wireless Ethernet (DHCP,
Static IP) or USB. References to Ethernet in this manual focus on the use of Wireless Ethernet via the
MVP’s WiFi Card.
Before commencing, verify you are using the latest NetLinx Master and
Modero panel-specific firmware. Verify you are using the latest versions of AMX’s
NetLinx Studio and TPDesign4 programs.
USB input devices must be plugged into the USB connectors on the docking stations
before the units are powered-up.
Modero Setup and System Settings
AMX Modero panels feature on-board Setup pages. Use the options in the Setup pages to access panel
information and make various configuration changes.
Accessing the Setup and Protected Setup Pages
1. Press down and hold both the bottom, left pushbutton and down on the directional pad
simultaneously for 3-5 seconds. This opens the Setup page.
Setup Page Access buttons:
Press and hold simultaneously for
3-5 seconds to access the Setup pages
Press and hold for 6 seconds
to access the Calibration page.
FIG. 13 Setup Page Access buttons
2. Press the Protected Setup button. This invokes a keypad for entry of the password to allow access to
the Protected Setup page. Enter 1988 (the default password), and press Done to proceed.
19
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Configuring Communications
Setting the Panel’s Device Number
In the Protected Setup page:
FIG. 14 Protected Setup page
Enter a unique Device Number assignment for the panel, and press Done to return to the Protected
Setup page. The Device Number range is 1 - 32000, the default is 10001.
2. Press Reboot to reboot the panel, and apply the new Device Number.
Wireless Settings Page - Wireless Access Overview
Hot Swapping
Hot swapping is not an issue on these panels as the card is installed within the unit and cannot be
removed without first removing the housing.
In the case of DHCP, there must be a DHCP server accessible before the fields are populated.
If the SSID (Network Name) and WEP fields have not previously been configured, the
Wireless Settings page will not work until the panel is rebooted.
Before selecting Ethernet as the Master Connection Type you must setup the parameters of the wireless
card. The Wireless Access Point communication parameters must match those of the pre-installed
wireless CF card inside the MVP.
The MVP touch panels allow users to connect to a wireless network through their use of the
pre-installed AMX 802.11g wireless interface card to communicate with a Wireless Access Point (WAP)
such as the NXA-WAP200G). The WAP communication parameters must match those of the
pre-installed wireless interface card installed within the panel. This internal card transmits data
wirelessly using the 802.11x signals at 2.4 GHz. For a more detailed explanation of the new security and
encryption technology, refer to the section of the document entitled: Appendix B - Wireless
For more information on utilizing the AMX Certificate Upload Utility in conjunction with the EAP
security, refer to the section of the document entitled: Appendix B - Wireless Technology section on
20
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Configuring Communications
Configuring a Wireless Network Access
When working with a wireless card, the first step is to configure wireless communication parameters
within the Wireless Settings page. This page only configures the card to communicate to a target WAP
(such as the NXA-WAP200G), it is still necessary to tell the panel which Master it should be
communicating with. This "pointing to a Master" is done via the System Settings page where you
configure the IP Address, System Number and Username/Password information assigned to the target
Master.
Step 1: Configure the Panel’s Wireless IP Settings
The first step to successfully setting up your internal wireless card is to configure the IP Settings section
on the Wireless Settings page. The section configures the communication parameters from the MVP
panel to the web.
Wireless communication using a DHCP Address
In the Protected Setup page:
1. Select Wireless Settings. Wireless communication is set within the IP Settings section of this page
2. Toggle the DHCP/Static field (from the IP Settings section) until the choice cycles to DHCP. This
action causes all fields in the IP Settings section (other than Host Name) to be greyed-out.
Do not alter any of these remaining greyed-out fields in the IP Settings section. Once the panel is
rebooted, these values are obtained by the unit and displayed in the DNS fields after power-up.
DHCP will register the unique MAC Address (factory assigned) on the panel and
once the communication setup process is complete, assign IP Address, Subnet
Mask, and Gateway values from the DHCP Server.
3. Press the optional Host Name field to open a Keyboard and enter the Host Name information.
Modero
connection
IP info.
Wireless Access Point
Site Survey Button
FIG. 15 Wireless Settings page (IP Settings section)
4. Press Done after you are finished assigning the alpha-numeric string of the host name.
5. Do not alter any of these remaining greyed-out fields in the IP Settings section. Once the panel is
rebooted, these values are obtained by the unit and displayed in the DNS fields after power-up.
21
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Configuring Communications
This information can be found in either the Workspace - System name > Define
Device section of your code (that defines the properties for your panel), or in the
Device Addressing/Network Addresses section of the Tools > NetLinx Diagnostics
dialog.
6. Setup the security and communication parameters between the wireless card and the target WAP by
configuring the Wireless Settings section on this page. Refer to Step 2: Configure the Card’s
unsecure connection.
Wireless communication using a Static IP Address
In the Protected Setup page:
1. Press the Wireless Settings button (located on the lower-left) to open the Wireless Settings page.
Wireless communication is set within the IP Settings section of this page (FIG. 15).
Check with your System Administrator for a pre-reserved Static IP Address assigned
to the panel. This address must be obtained before Static assignment of the panel
continues.
2. Toggle the DHCP/Static field (from the IP Settings section) until the choice cycles to Static.
The IP Address, Subnet Mask, and Gateway fields then become user-editable (red).
3. Press the IP Address field to open a Keyboard and enter the Static IP Address (provided by your
System Administrator).
4. Press Done after you are finished entering the IP information.
5. Repeat the same process for the Subnet Mask and Gateway fields.
6. Press the optional Host Name field to open the Keyboard and enter the Host Name information.
7. Press Done after you are finished assigning the alpha-numeric string of the host name.
8. Press the Primary DNS field to open a Keyboard, enter the Primary DNS Address (provided by your
System Administrator) and press Done when compete. Repeat this process for the Secondary DNS
field.
9. Press the Domain field to open a Keyboard, enter the resolvable domain Address (this is provided
by your System Administrator and equates to a unique Internet name for the panel), and press Done
when complete.
10. Setup the security and communication parameters between the wireless card and the target WAP by
configuring the Wireless Settings section on this page. Refer to the following section for detailed
procedures to setup either a secure or unsecure connection.
Using the Site Survey tool
This tool allows a user to "sniff-out" all transmitting Wireless Access Points within the detection range
of the internal NXA-WC80211GCF. Once pressed, the panel displays the Site Survey page which
contains categories such as:
ꢀ
ꢀ
ꢀ
Network Name (SSID) - Wireless Access Point names
Channel (RF) - Channel currently being used by the WAP (Wireless Access Point)
Security Type (if detectable - such as WEP, OPEN and UNKNOWN) - security protocol
enabled on the WAP
ꢀ
ꢀ
Signal Strength - None, Poor, Fair, Good, Very Good, and Excellent
MAC Address - Unique identification of the transmitting Access Point
22
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Configuring Communications
Indicates the currently
active column and the order
in which the data is being sorted -
(Descending order shown)
Indicates a selected AP
FIG. 16 Site Survey page
In the Protected Setup page:
1. Press the Wireless Settings button (located on the lower-left) to open the Wireless Settings page.
2. Navigate to the Access Point MAC Address section of this page and press the on-screen
Site Survey button. This action launches the Site Survey page which displays a listing of all
detected WAPs in the communication range of the internal card.
ꢀ
The card scans its environment every four seconds and adds any new WAPs found to the list.
Every scan cycle updates the signal strength field.
ꢀ
Access points are tracked by MAC Address.
ꢀ
If the WAP’s SSID is set as a blank, then N/A is displayed within the SSID field.
ꢀ
If the WAP’s SSID is hidden (not broadcast) it will not show up on the site survey
screen but it can still be configured via the SSID field on the specified security mode
screen.
ꢀ
If a WAP is displayed in the list is not detected for 10 scans in a row it is then
removed from the screen. In this way, a user can walk around a building and see
access points come and go as they move in and out of range.
3. Sort the information provided on this page by pressing on a column name and toggling the direction
of the adjacent arrow.
ꢀ
Up arrow - indicates that the information is being sorted in a Ascending order.
ꢀ
SSID (A to Z), Channel (1 to 14), Security (Unknown to WEP), Signal (None to
Excellent). The firmware considers the following to be the security order from least
secure to most secure: Open, WEP, WPA, WPA2, and Unknown.
ꢀ
Down arrow - indicates that the information is being sorted in a Descending order.
ꢀ
SSID (Z to A), Channel (11 to 6), Security (WEP to Unknown), Signal (Excellent
to None)
If the panel detects more than 10 WAPs, the Up/Down arrows at the far right side of
the page become active (blue) and allow the user to scroll through the list of entries.
23
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Configuring Communications
4. Select a desired Access Point by touching the corresponding row. The up arrow and down arrow
will be grayed out if there are ten or less access points detected. If there are more, then they will be
enabled as appropriate so that the user can scroll through the list.
5. With the desired WAP selected and highlighted, click the Connect button to be directed to the
selected security mode’s Settings page with the SSID field filled in. You can then either Cancel the
operation or fill in any necessary information fields and then click Save.
If you select an Open, WEP, and WPA-PSK Access Point and then click Connect, you will be flipped
to the corresponding Settings page. For any other security mode, if you click Connect you will only
return to the previous page without any information being pre-filled out for you.
ꢀ
In an Open security mode, when a target WAP is selected and the connect to, the SSID name
of the selected WAP is saved for the open security mode.
ꢀ
In a Static WEP security mode, when a WEP Access Point is selected and then connected to,
the user is then redirected back to the Static WEP security screen where the SSID field is
already filled out and the user is only required to enter in the remaining WEP key settings.
ꢀ
A similar process occurs for WPA-PSK access points. For any other case, the firmware
switches back to the previous page and security and connection parameters must be entered in
as normal.
Step 2: Configure the Card’s Wireless Security Settings
The second step to successfully setting up your wireless card is to configure the Wireless Settings section
of the Wireless Settings page. This section configures both the communication and security parameters
from the internal wireless card to the WAP. The procedures outlined within the following sections use
an 802.11g card to configure a common security configuration to a target WAP.
Once you have set up the wireless card parameters, you must configure the communication parameters
24
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Configuring Communications
Configuring the Modero’s wireless card for unsecured access to a WAP200G
In the Protected Setup page:
1. Press the Wireless Settings button (located on the lower-left) to open the Wireless Settings page.
MVP
connection
Wireless
card security settings
IP info.
FIG. 17 Wireless Settings page (showing a sample unsecured configuration)
2. Enter the SSID information by either:
ꢀ
Automatically having it filled in by pressing the Site Survey button and from the Site Survey
page, choosing an Open WAP from within the Site Survey page and then pressing the
Connect button.
Select an OPEN
(unsecured) WAP
Connecting to the
WAP begins the
communication
FIG. 18 Site Survey of available WAPS (Unsecured WAP shown selected)
ꢀ
Manually entering the SSID information into their appropriate fields by following steps 7
thru 9.
3. From within the Wireless Security section, press the Open (Clear Text) button to open the Open
methodology but does require that an SSID (alpha-numeric) be entered. Using this method causes
network packets to be sent out as unencrypted text.
25
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Configuring Communications
Required Information:
- SSID (Network Name used by the Target WAP)
By default, this field displays the
SSID - AMX
FIG. 19 Wireless Settings page - Open (Clear Text) security method
5. In this keyboard, enter the SSID name used on your target Wireless Access Point (case sensitive).
ꢀ
The card should be given the SSID used by the target WAP. If this field is left blank, the unit
will attempt to connect to the first available WAP. By default, all WAP200Gs use AMX as
their assigned SSID value.
ꢀ
One of the most common problems associated with connection to a WAP arise because the
SSID was not entered properly. You must maintain the same case when entering the SSID
information. ABC is not the same as Abc.
6. Click Done when you’ve completed typing in the information.
7. From the Open (Clear Text) Settings page (FIG. 19), press the Save button to incorporate your new
information into the panel and begin the communication process.
8. Verify the fields in the IP Settings section have been properly configured. Refer to Step 1: Configure
9. Press the Back button to return to the Protected Setup page and press the on-screen Reboot button
to both save any changes and restart the panel. Remember that you will need to navigate to the
System Settings page and configure the connection to a target Master.
10. After the panel restarts, return to the Wireless Settings page’s RF Link Info section and verify the
Link Quality and Signal Strength:
ꢀ
The signal strength field should provide some descriptive text regarding the strength
of the connection to a Wireless Access Point. If there is no signal or no IP Address
displayed; configuration of your network could be required.
26
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Configuring Communications
Configuring the Modero’s wireless card for secured access to a WAP200G
After logging into the WAP200G, the default Status page appears within the web browser. These
read-only values are "pulled" from some of the other user-configurable Configuration Utility pages. By
default, wireless Modero panels are configured for unsecured communication to a Wireless Access
Point. To properly setup both the WAP200G and panel for secure communication, you must first prepare
the Modero panel and then use the information given to fill out the fields within the WAP’s
browser-based Basic Wireless Configuration page.
Since the code key generator on Modero panels use the same key generation formula, all panels will
generate identical keys for the same Passphrase. The generators used on WAPs will not produce the same
key as the Modero generator even if you use the same Passphrase. For this reason, we recommend
FIRST creating the Current Key on the Modero and then entering that information into the
appropriate NXA-WAP200G fields.
Automatically set SSID
In the Protected Setup page:
1. Select Wireless Settings.
2. Press the Site Survey button.
3. Select a WEP secured WAP from within the Site Survey page, and press the Connect button .
Select a target
WAP with the
desired level of
security
Connecting to the
WAP begins the
communication
FIG. 20 Site Survey of available WAPs (Secured WAP shown selected)
4. Write down the SSID name, Current Key string value, and panel MAC Address information so you
can later enter it into the appropriate WAP dialog fields in order to "sync-up" the secure connection.
These values must be identically reproduced on the target WAP.
27
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Configuring Communications
Manually set SSID
In the Protected Setup page:
1. Select Wireless Settings.
802.11g wireless card
FIG. 21 Wireless Settings page
You must first take down the SSID name, Current Key string value, and panel MAC
Address information so you can later enter it into the appropriate WAP dialog fields in
order to "sync-up" the secure connection. These values must be identically
reproduced on the target WAP.
Required Information:
- SSID (Network Name used by the Target WAP)
- Encryption Method
- Passphrase
- WEP Key assignment
- Authentication Method
FIG. 22 Wireless Settings page - Static WEP security method
4. Press the SSID field and from the Network Name (SSID) keyboard, enter the SSID name you are
using on your target Wireless Access Point (case sensitive), and press Done when finished.
ꢀ
ꢀ
ꢀ
The card should be given the SSID used by the target WAP. If this field is left blank, the unit
will attempt to connect to the first available WAP. By default, all WAP200Gs use AMX as
their assigned SSID value.
One of the most common problems associated with connection to a WAP arise because the
SSID was not entered properly. You must maintain the same case when entering this
information. ABC is not the same as Abc.
The alpha-numeric string is by default AMX but can later be changed to any 32-character
entry. This string must be duplicated within the Network Name (SSID) field on the WAP.
28
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Configuring Communications
ꢀ
As an example, if you use TECHPUBS as your SSID, you must match this word and the
case within both the Network Name (SSID) field on the touch panel’s Network Name SSID
field and on the WAP’s Basic Wireless Configuration page.
5. Toggle the Encryption field (FIG. 22) until it reads either: 64 Bit Key Size or 128 Bit Key Size.
The 64/128 selection reflects the bit-level of encryption security. This WEP encryption level must
match the encryption level being used on the WAP.
WEP will not work unless the same Default Key is set on both the panel and the
Wireless Access Point.
For example: if you have your Wireless Access Point set to default key 4 (which
was 01:02:03:04:05), you must set the panel’s key 4 to 01:02:03:04:05.
6. Toggle the Default Key field until the you’ve chosen a WEP Key value (from 1- 4) that matches
what you’ll be using on your target WAP200G. This value MUST MATCH on both devices.
ꢀ
These WEP Key identifier values must match for both devices.
7. With the proper WEP Key value displayed, press the Generate button to launch the WEP
Passphrase keyboard.
If you are wanting to have your target WAP (other than an NXA-WAP200G) generate the
Current Key - Do not press the Generate button and continue with Step 13.
ꢀ
This keyboard allows you to enter a Passphrase (such as AMXPanel) and then
AUTOMATICALLY generate a WEP key which is compatible only among all Modero panels.
The code key generator on Modero panels use the same key generation formula.
Therefore, this same Passphrase generates identical keys when done on any
Modero because they all use the same Modero-specific generator. The Passphrase
generator is case sensitive.
8. Within this on-screen WEP Passphrase keyboard (FIG. 23), enter a character string or word (such as
AMXPanel) and press Done when you have finished.
FIG. 23 WEP Passphrase Keyboard
29
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Configuring Communications
ꢀ
As an example, enter the word AMXPanel using a 128-bit hex digit encryption. After
pressing Done, the on-screen Current Key field displays a long string of characters (separated
by colons) which represents the encryption key equivalent to the word AMXPanel.
ꢀ
This series of hex digits (26 hex digits for a 128-bit encryption key) should be entered as
the Current Key into both the WAP and onto other communicating Modero panels by
using the WEP Key dialog (FIG. 24).
FIG. 24 WEP Key # Keyboard
9. Write down this Current Key string value for later entry into your WAP’s WEP Key field (typically
10. If you are entering a Current Key generated either by your target WAP or another Modero
panel, within the WEP Keys section, touch the Key # button to launch the WEP Key # keyboard
ꢀ
This Key value corresponds to the Default WEP Key number used on the Wireless Access
Point and selected in the Default Key field described in the previous step.
If your target Wireless Access Point does not support passphrase key generation and
has previously been setup with a manually entered WEP KEY, you must manually
enter that same WEP key on your panel.
11. The remaining Current Key and Authentication fields are greyed-out and cannot be altered by the
user.
12. Verify the fields within the IP Settings section have been properly configured. Refer to Step 1:
13. Press the Back button to navigate to the Protected Setup page and press the on-screen Reboot
button to both save any changes and restart the panel. Remember that you will need to navigate to
the System Settings page and configure the connection to a target Master.
14. After the panel restarts, return to the Wireless Settings page to verify the Link Quality and Signal
Strength:
ꢀ
The descriptions are: None, Poor, Fair, Good, Very Good, and Excellent.
The signal strength field provides some descriptive text regarding the strength of the
connection to a Wireless Access Point. If there is no signal or no IP Address
displayed; configuration of your network could be required.
Refer to the NXA-WAP200G Instruction Manual for more detailed setup and configuration procedures.
30
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Configuring Communications
Configuring multiple wireless Moderos to communicate to a target WAP200G
1. For each communicating touch panel, complete all of the steps outlined within the previous
2. Navigate back to the Wireless Settings page on each panel.
3. Verify that all communicating Modero panels are using the same SSID, encryption level, Default
Key #, and an identical Current Key value.
ꢀ
As an example, all panels should be set to Default Key #1 and be using aa:bb:cc..as the
Current Key string value. This same Key value and Current Key string should be used on the
target WAP.
4. Repeat steps 1 - 3 on each panel. Using the same passphrase, generates the same key for all
communicating Modero panels.
Step 3: Choose a Master Connection Mode
The panel requires you establish the type of connection you want made between it and your master.
In the Protected Setup page:
1. Select System Settings.
2. Select Type to toggle between the Master Connection Types USB and Ethernet.
ꢀ
ꢀ
A USB connection is a direct connection from the panel’s mini-USB port to a corresponding
USB port on the PC (acting as a Virtual Master).
A Wireless Ethernet connection involves indirect communication from the panel to a Master
via a wireless connection to the network.
It is recommended that firmware KIT files only be transferred over a direct connection
and only when the panel is connected to a power supply. If battery power or wireless
connection fails during a firmware upgrade, the panel flash file system may become
corrupted.
FIG. 25 System Settings page
USB
NetLinx Studio can be setup to run a Virtual Master where the PC acts as the Master by supplying its
own IP Address for communication to the panel. For a PC to establish a USB connection with a Modero
panel, it must have the AMX USBLAN driver installed.
31
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Configuring Communications
The AMX USBLAN driver is included with both NetLinx Studio2 and TPDesign4, and
can also be downloaded as a stand-alone application from www.amx.com.
Prepare your PC for USB communication with the panel
If you haven’t already done so, download and install the latest versions of NetLinx Studio2 and
TPDesign4 (from www.amx.com), and restart your PC.
Configure the panel for USB communication
The first time the panel is connected to the PC it is detected as a new USB hardware device, and the
correct (panel-specific) USBLAN driver must be associated to it manually. Each time thereafter, the
panel is recognized as a unique USBLAN device, and the association to the driver is handled
automatically.
1. Connect the PS4.4 power connector to the panel (or docking station if the panel is already installed)
to supply power.
2. Press and hold the two lower external pushbuttons on either side of the panel simultaneously for 3
seconds to access the Setup page (see FIG. 13 on page 19).
3. In the Protected Settings page, select System Settings to open the System Settings page (FIG. 26).
4. Toggle the blue Type field (from the Master Connection section) until the choice cycles to USB.
FIG. 26 System Settings page - USB Connection
5. Press the Back button to return to the Protected Setup page.
6. Press Reboot to save changes and restart the panel.
7. When the panel powers up and displays the first panel page, insert the mini-USB connector into the
Program Port on the panel.
It may take a minute for the panel to detect the new connection and send a signal to the PC
(indicated by a green System Connection icon).
The first time the panel is recognized by the PC as a new USB device, a USB driver installation
a USB device, and the appropriate USB driver is being installed to establish communication with
32
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Configuring Communications
the panel. It also indicates that the AMX USBLAN driver does not contain a Microsoft® digital
signature.
FIG. 27 USB driver installation popup window
8. Click Yes to proceed with the driver installation.
Once the installation is complete, the panel and PC are ready to communicate via USB.
9. Navigate back to the System Settings page.
Configure a Virtual NetLinx Master using NetLinx Studio
A Virtual NetLinx Master (VNM) is used when the target panel is not connected to a physical NetLinx
Master. In this situation, the PC takes on the functions of a Master via a Virtual NetLinx Master. This
connection is made by either using the PC’s Ethernet Address (via TCP/IP using a known PC’s IP
Address as the Master) or using a direct mini-USB connection to communicate directly to the panel.
Before beginning:
1. Verify the panel has been configured to communicate via USB within the System Settings page and
that the USB driver has been properly configured. Refer to the previous section for more
information.
2. In NetLinx Studio, select Settings > Master Communication Settings, from the Main menu to
open the Master Communication Settings dialog (FIG. 28).
33
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Configuring Communications
IP Address of computer
(not needed as this is a direct
USB connection)
FIG. 28 Assigning Communication Settings for a Virtual Master
3. Click the Communications Settings button to open the Communications Settings dialog.
4. Click the NetLinx Master radio button (from the Platform Selection section).
5. Click the Virtual Master radio button (from the Transport Connection Option section).
7. Enter the System number (default is 1).
8. Click OK to close all open dialogs and save your settings.
9. Click the OnLine Tree tab in the Workspace window to view the devices on the Virtual System.
10. Right-click on Empty Device Tree/System and select Refresh System to re-populate the list.
The panel will not appear as a device below the virtual system number (in the Online Tree tab)
until both the system number (default = 1) is entered into the Master Connection section of the
System Settings page and the panel is restarted.
ꢀ
The Connection status turns green after a few seconds to indicate an active USB connection to
the PC (Virtual Master).
ꢀ
If the System Connection icon does not turn green, check the USP connection and
communication settings and refresh the system.
34
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Configuring Communications
Ethernet
1. When using Ethernet, press the listed Mode to toggle through the available connection modes:
Connection Modes
Mode Description
Procedures
Auto
URL
The device connects to the first master that
responds. This setting requires you set the
System Number.
Setting the System Number:
1. Select the System Number to open the keypad.
2. Set your System Number select Done.
Setting the Master IP:
The device connects to the specific IP of a
master via a TCP connection. This setting
requires you set the Master’s IP.
1. Select the Master IP number to the keyboard.
2. Set your Master IP and select Done.
Listen The device "listens" for the master to initiate
contact. This setting requires you provide the
master with the device’s IP.
Confirm device IP is on the Master URL list. You
can set the Host Name on the device and use it to
locate the device on the master. Host Name is
particularly useful in the DHCP scenario where the
IP address can change.
2. Select the Master Port Number to open the keypad and change this value. The default setting for the
port is 1319.
3. Set your Master Port and select Done.
If you have enabled password security on your master you need to set the username and password within
the device.
4. Select the blank field Username to open the keyboard.
5. Set your Username and select Done.
6. Select the blank field Password to open the keyboard.
7. Set your Password and select Done.
8. Press the Back button to return to the Protected Setup page.
9. Press the Reboot button to reboot device and confirm changes.
Master Connection to a Virtual Master via Ethernet
When configuring your panel to communicate with a Virtual Master (on your PC) via
wireless Ethernet, the Master IP/URL field must be configured to match the IP
Address of the PC and make sure to use the Virtual System value assigned to the
Virtual Master within NetLinx Studio.
Before beginning:
1. Verify the panel has been configured to communicate with the Wireless Access Point and verify the
signal strength quality bargraph is On.
2. Launch NetLinx Studio 2.x (default location is Start > Programs > AMX Control Disc > NetLinx
Studio 2 > NetLinx Studio 2).
3. Select Settings > Master Communication Settings, from the Main menu to open the Master
Communication Settings dialog (FIG. 29).
35
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Configuring Communications
Enter this IP
into the
Master IP/URL
field on the
System Settings
page
IP Addresses of computer
(also obtained by using the
Start > Run > cmd command)
FIG. 29 Assigning Communication Settings and TCP/IP Settings for a Virtual Master
4. Click the Communications Settings button to open the Communications Settings dialog.
5. Click on the NetLinx Master radio button (from the Platform Selection section) to indicate that you
are working as a NetLinx Master.
6. Click on the Virtual Master radio box (from the Transport Connection Option section) to indicate
you are wanting to configure the PC to communicate with a panel. Everything else such as the
Authentication is greyed-out because you are not going through the Master’s UI.
7. Click the Edit Settings button (on the Communications Settings dialog) to open the Virtual NetLinx
Master Settings dialog (FIG. 29).
8. From within this dialog enter the System number (default is 1) and note the IP Address of the target
PC being used as the Virtual Master. This IP Address can also be obtained by following these
procedures:
ꢀ
ꢀ
ꢀ
On your PC, click Start > Run to open the Run dialog.
Enter cmd into the Open field and click OK to open the command DOS prompt.
From the C:\> command line, enter ipconfig to display the IP Address of the PC. This
information is entered into the Master IP/URL field on the panel.
9. Click OK three times to close the open dialogs, save your settings, and return to the main NetLinx
Studio application.
10. Click the OnLine Tree tab in the Workspace window to view the devices on the Virtual System. The
default System value is one.
11. Right-click on the Empty Device Tree/System entry and select Refresh System to re-populate the
list.
12. Connect the terminal end of the PS4.4 power cable to the 12 VDC power connector on the side of
the stand-alone touch panel.
ꢀ
If the MVP is installed onto a docking station, feed power to the docked panel by connecting
the appropriate power supply to the docking station.
13. After the panel powers-up, press and hold the two lower buttons on both sides of the display (for 3
seconds) to continue with the setup process and proceed to the Setup page.
14. Select Protected Setup > System Settings (located on the lower-left) to open the System Settings
page (FIG. 30).
36
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Configuring Communications
The System Number is
assigned to the Master
within the AMX
software application
(these must match)
Enter the IP Address
information of the PC
used as a Virtual
Master
When using a Virtual Master,
there is no need to enter a
username and/or password
FIG. 30 Sample System Settings page (for Virtual Master communication)
15. Press the blue Type field (from the Master Connection section) until the choice cycles to the word
Ethernet.
16. Press the Mode field until the choice cycles to the word URL.
ꢀ By selecting URL, the System Number field becomes read-only (grey) because the panel pulls
this value directly from the communicating target Master (virtual or not). A Virtual Master
system value can be set within the active AMX software applications such as: NetLinx Studio,
TPD4, or IREdit.
17. Press the Master IP/URL field to open a Keyboard and enter the IP Address of the PC used as the
Virtual Master.
18. Click Done to accept the new value and return to the System Settings page.
19. Do not alter the Master Port Number value (this is the default value used by NetLinx).
20. Press the Back button to open the Protected Setup page.
21. Press the on-screen Reboot button to both save any changes and restart the panel.
37
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Configuring Communications
Using G4 Web Control to Interact with a G4 Panel
The G4 Web Control feature allows you to use a PC to interact with a G4 enabled panel via the web. This
feature works in tandem with the new browser-capable NetLinx Security firmware update (build 300 or
higher). G4 Web Control is only available with the latest Modero panel firmware.
Verify your NetLinx Master (ME260/64 or NI-Series) has been installed with the latest
firmware KIT file from www.amx.com. Refer to your NetLinx Master instruction
manual for more detailed information on the use of the new web-based NetLinx
Security.
1. Press and hold the two lower buttons on both sides of the display for 3 seconds to open the Setup
page.
2. Press the Protected Setup button (located on the lower-left of the panel page) to open the Protected
Setup page and display an on-screen keypad.
3. Enter 1988 into the Keypad’s password field (1988 is the default password).
Clearing Password #5, from the initial Password Setup page, removes the need for
you to enter the default password before accessing the Protected Setup page.
4. Press Done when finished.
FIG. 31 G4 Web Control page
6. Press the Enable/Enabled button until it toggles to Enabled (light blue color).
7. The Network Interface Select field is read-only and displays the method of communication to the
web.
ꢀ
Wireless is used when a wireless card is detected within the internal card slot. This method
provides an indirect communication to the web via a pre-configured Wireless Access Point.
The Network Interface Select field is read-only and defaulted to Wireless (since
there is no Ethernet cable connection).
8. Press the Web Control Name field to open the Web Name keyboard.
38
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Configuring Communications
9. From the Web Name keyboard, enter a unique alpha-numeric string to identify this panel. This
information is used by the NetLinx Security Web Server to display on-screen links to the panel. The
on-screen links use the IP Address of the panel and not the name for communication (FIG. 32).
FIG. 32 Sample relationship between G4 Web Control and Mange WebControl Connections window
10. Press Done after you are finished assigning the alpha-numeric string for the Web Control name.
11. Press the Web Control Password field to open the Web Password keyboard.
12. From the Web Password keyboard, enter a unique alpha-numeric string to be assigned as the G4
Authentication session password associated with VNC web access of this panel.
13. Press Done after you are finished assigning the alpha-numeric string for the Web Control password.
14. Press the Web Control Port field to open the Web Port Number keypad.
15. Within the keypad, enter a unique numeric value to be assigned to the port the VNC Web Server is
running on. The default value is 5900.
16. Press Done when you are finished entering the value. The remaining fields within the G4 Web
Control Settings section of this page are read-only and cannot be altered.
17. Press the Up/Down arrows on either sides of the G4 Web Control Timeout field to increase or
decrease the amount of time the panel can remain idle (no cursor movements) before the session is
closed and the user is disconnected.
18. Press the Back button to open the Protected Setup page.
19. Press the on-screen Reboot button to save any changes and restart the panel.
Verify your NetLinx Master’s IP Address and System Number have been properly
entered into the Master Connection section of the System Settings page.
39
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Configuring Communications
Using your NetLinx Master to control the G4 panel
Refer to your particular NetLinx Master’s instruction manual for detailed information on how to
download the latest firmware from www.amx.com. This firmware build enables SSL certificate
identification and encryption, HTTPS communication, ICSP data encryption, and disables the ability to
alter the Master security properties via a TELNET session.
In order to fully utilize the SSL encryption, your web browser should incorporate the an encryption
feature. This encryption level is displayed as a Cipher strength.
Once the Master’s IP Address has been set through NetLinx Studio version 2.x or higher:
1. Launch your web browser.
2. Enter the IP Address of the target Master (ex: http://198.198.99.99) into the web browser’s Address
field.
3. Press the Enter key on your keyboard to begin the communication process between the target
Master and your computer.
ꢀ
ꢀ
ꢀ
Initially, the Master Security option is disabled (from within the System Security page) and
no username and password is required for access or configuration.
Both HTTP and HTTPS Ports are enabled by default (via the Manage System > Server
page).
If the Master has been previously configured for secured communication, click OK to accept
the AMX SSL certificate (if SSL is enabled) and then enter a valid username and password
into the fields within the Login dialog.
4. Click OK to enter the information and proceed to the Master’s Manage WebControl Connections
window.
connections link (within the Web Control section within the Navigation frame). Once activated, this
page displays links to G4 panels running the latest G4 Web Control feature (previously setup and
activated on the panel).
Compatible
devices field
(showing G4
WebControl links)
G4 panels
Compression
Options
FIG. 33 Manage WebControl Connections page (populated with compatible panels)
40
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Configuring Communications
6. Click on the G4 panel name link associated with the target panel. A secondary web browser window
appears on the screen (FIG. 34).
FIG. 34 Web Control VNC installation and Password entry screens
7. Click Yes from the Security Alert popup window to agree to the installation of the G4 WebControl
application on your computer. This application contains the necessary Active X and VNC client
applications necessary to properly view and control the panel pages from your computer.
The G4 Web Control application is sent by the panel to the computer that is used for
communication. Once the application is installed, this popup will no longer appear.
This popup will only appear if you are connecting to the target panel using a different
computer.
Address. This is the IP Address not the IP of the Master but of the target touch panel. Depending on
which method of communication you are using, it can be found in either the:
ꢀ
ꢀ
ꢀ
Wired Ethernet - System Settings > IP Settings section within the IP Address field.
Wireless - Wireless Settings > IP Settings section within the IP Address field.
If you do not get this field continue to step 9.
IP Address of touch panel
- obtained from IP Settings section of
the Wireless Settings page (MVP)
FIG. 35 Connection Details dialog
9. If a WebControl password was setup on the G4 WebControl page, a G4 Authentication Session
password dialog box appears on the screen within the secondary browser window.
41
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Configuring Communications
was previously entered into the Web Control Password field within the G4 Web Control page on the
panel.
11. Click OK to send the password to the panel and begin the session. A confirmation message appears
stating "Please wait, Initial screen loading..".
The secondary window then becomes populated with the same G4 page being displayed on the target G4
panel. A small circle appears within the on-screen G4 panel page and corresponds to the location of the
mouse cursor. A left-mouse click on the computer-displayed panel page equates to an actual touch on the
target G4 panel page.
42
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Upgrading MVP Firmware
Upgrading MVP Firmware
Except for the MVP-KS (Kickstand for MVP Panels), all MVP panels and their accessories have on-
board firmware which is upgradeable through the use of the latest NetLinx Studio. The MVP acts as a
bridge between the NetLinx Studio program and the installed docking station. Studio can download
firmware to the target docking station by using the connected MVP to pass-along the Kit file to the
docking station. Refer to the NetLinx Studio version 2.x or higher Instruction Manual for more
information on how to download firmware to both a panel and a docking station.
The latest firmware 2.70.xx (or higher) kit file is panel-specific.
This new firmware also provides both backwards compatibility with the previous
802.11b cards and new security protocols for the new 802.11g wireless CF card.
1. Upload the latest Kit file (SW5965_xx version 2.70.xx or higher) to your specific Modero touch
panel and then confirm the firmware file update was successful. Refer to your panel’s instruction
manual for detailed communication and Kit file upload procedures.
If you don’t first update the firmware file on the panel, before proceeding with the card
upgrade process, you will be required to configure NetLinx Studio to communicate
with the target panel via a direct USB connection.
In this communication scenario, your PC acts as a Virtual NetLinx Master establishing
a secure USB connection to the target panel and then uploading the new Kit file.
Before beginning the Upgrade process:
ꢀ
ꢀ
ꢀ
ꢀ
Setup and configure your NetLinx Master. Refer to the your particular NetLinx Master
Instruction Manual for detailed setup procedures.
Calibrate and prepare the communication pages on the Modero panel for use. Refer to the
Refer to the NetLinx Studio version 2.x or higher Help file for more information on uploading
files via Ethernet.
Configure your panel for either direct connect or wireless communication. Refer to the
Ethernet or Wireless communication.
It is recommended that firmware Kit files only be transferred over a direct connection
and only when the panel is connected to a power supply.
If battery power or wireless connection fails during a firmware upgrade, the panel
flash file system may become corrupted.
The process of updating firmware involves the use of a communicating NetLinx Master. The required
steps for updating firmware to a Modero panel are virtually identical to those necessary for updating Kit
files to a NetLinx Master (except the target device is a panel instead of a Master). Refer to either your
Master’s literature or Studio 2.x Help file for those procedures.
A touch panel which is not using a valid username and password will not be able to
communicate with a secured Master. If you are updating the firmware on or through a
panel which is not using a username or password field, you must first remove the
Master Security feature to establish an unsecured connection.
43
MVP-8400i Modero Viewpoint Wireless Touch Panels
Upgrading MVP Firmware
Upgrading the Modero Firmware via the USB port
Before beginning with this section, verify your panel is powered and the Type-A USB connector is
securely inserted into the PC’s USB port. The panel must be powered-on before connecting the mini-
USB connector to the panel.
Establishing a USB connection between the PC and the panel, prior to installing the
USB Driver will cause a failure in the USB driver installation.
Step 1: Configure the panel for a USB Connection Type
1. After the installation of the USB driver has been completed, confirm the proper installation of the
large Type-A USB connector to the PC's USB port, and restart your machine.
2. After the panel powers-up, press and hold the two lower buttons on both sides of the display for
3 seconds to continue with the setup process and proceed to the Setup page.
3. Select Protected Setup > System Settings (located on the lower-left) to open the System Settings
page.
4. Toggle the blue Type field (from the Master Connection section) until the choice cycles to USB.
ALL fields are then greyed-out and read-only, but still display any previous network
information.
5. Press the Back button on the touch panel to return to the Protected Setup page.
6. Press the on-screen Reboot button to both save any changes and restart the panel. Remember that
the panel’s connection type must be set to USB prior to rebooting the panel and prior to inserting
the USB connector.
7. ONLY AFTER the unit displays the first panel page, THEN insert the mini-USB connector into
the Program Port on the panel. It may take a minute for the panel to detect the new connection and
send a signal to the PC (indicated by a green System Connection icon).
ꢀ
If a few minutes have gone by and the System Connection icon still does not turn green,
complete the procedures in the following section to setup the Virtual Master and refresh the
System from the Online Tree. This action sends out a request to the panel to respond and
completes the communication (turning the System Connection icon green).
8. Navigate back to the System Settings page.
Step 2: Prepare Studio for communication via the USB port
1. Launch NetLinx Studio 2.x (default location is Start > Programs > AMX Control Disc > NetLinx
Studio 2 > NetLinx Studio 2).
2. Select Settings > Master Communication Settings, from the Main menu to open the Master
Communication Settings dialog (FIG. 36).
3. Click the Communications Settings button to open the Communications Settings dialog.
4. Click on the NetLinx Master radio button (from the Platform Selection section) to indicate that you
are working as a NetLinx Master.
5. Click on the Virtual Master radio box (from the Transport Connection Option section) to indicate
you are wanting to configure the PC to communicate directly with a panel. Everything else such as
the Authentication is greyed-out because you are not going through the Master’s UI.
44
MVP-8400i Modero Viewpoint Wireless Touch Panels
Upgrading MVP Firmware
IP Address of computer
(not needed as this is a direct
USB connection)
FIG. 36 Assigning Communication Settings for a Virtual Master
6. Click the Edit Settings button (on the Communications Settings dialog) to open the Virtual NetLinx
7. From within this dialog enter the System number (default is 1).
8. Click OK three times to close the open dialogs, save your settings, and return to the main NetLinx
Studio application.
9. Click the OnLine Tree tab in the Workspace window to view the devices on the Virtual System.
The default System value is one.
10. Right-click on the Empty Device Tree/System entry and select Refresh System to re-populate the
list.
The panel will not appear as a device below the virtual system number (in the Online Tree tab)
until both the system number used in step 7 for the VNM is entered into the Master Connection
section of the System Settings page and the panel is restarted.
Step 3: Confirm and Upgrade the firmware via the USB port
Use the CC-USB Type-A to Mini-B 5-wire programming cable (FG10-5965) to provide communication
between the mini-USB Program port on the touch panel and the PC. This method of communication is
used to transfer firmware Kit files and TPD4 touch panel files.
A mini-USB connection is only detected after it is installed onto an active panel.
Connection to a previously powered panel which then reboots, allows the PC to
detect the panel and assign an appropriate USB driver.
1. Verify this direct USB connection (Type-A on the panel to mini-USB on the panel) is configured
properly using the steps outlined in the previous two sections.
2. With the panel already configured for USB communication and the Virtual Master setup within
NetLinx Studio, its now time to verify the panel is ready to receive files.
3. After the Communication Verification dialog window verifies active communication between the
view the devices on the Virtual System. The default System value is one.
4. Right-click on the System entry (FIG. 37) and select Refresh System to re-populate the list. Verify
the panel appears in the OnLine Tree tab of the Workspace window.
The default Modero panel value is 10001.
45
MVP-8400i Modero Viewpoint Wireless Touch Panels
Upgrading MVP Firmware
Showing the Virtual Master
firmware version and
device number
Shows NetLinx Studio
version number
Showing the current MVP
panel firmware version and
device number
FIG. 37 NetLinx Workspace window (showing panel connection via a Virtual NetLinx Master)
The panel-specific firmware is shown on the right of the listed panel.
Download the latest firmware file from www.amx.com and then save the Kit file to
your computer. Note that each kit file is intended for download to its corresponding
panel.
5. If the panel firmware version is not the latest available; locate the latest firmware file from the
www.amx.com > Tech Center > Downloadable Files > Firmware Files > Modero Panels section
of the website.
6. Click on the desired Kit file link and after you’ve accepted the Licensing Agreement, verify you
have downloaded the Modero Kit file to a known location.
7. Select Tools > Firmware Transfers > Send to NetLinx Device from the Main menu to open the
match those values listed within the System folder in the OnLine Tree tab of the Workspace
A
B
FIG. 38 Using USB for a Virtual Master transfer
8. Select the panel’s Kit file from the Files section.
9. Enter the Device value associated with the panel and the System number associated with the Master
(listed in the OnLine Tree tab of the Workspace window). The Port field is greyed-out.
46
MVP-8400i Modero Viewpoint Wireless Touch Panels
Upgrading MVP Firmware
10. Click the Reboot Device checkbox. This causes the touch panel to reboot after the firmware update
process is complete. The reboot of the panel can take up 30 seconds after the firmware process has
finished.
11. Click Send to begin the transfer. The file transfer progress is indicated on the bottom-right of the
12. As the panel is rebooting, temporarily unplug the USB connector on the panel until the panel has
completely restarted.
13. Once the first panel page has been displayed, reconnect the USB connector to the panel.
14. Right-click the associated System number and select Refresh System. This causes a refresh of all
project systems, establishes a new connection to the Master, and populates the System list with
devices on your particular system.
15. Confirm the panel has been properly updated to the correct firmware version.
Upgrading the Docking Station Firmware via USB
The following accessory devices are firmware upgradeable:
ꢀ
ꢀ
ꢀ
MVP-TDS Table Top Docking Station (FG5965-10)
MVP-WDS Wall/Flush Mount Docking Station - Black (FG5965-11)
MVP-WDS Wall/Flush Mount Docking Station - Silver (FG5965-21)
This device is not given a unique device number which would ordinarily appear within the Online Tree
tab of NetLinx Studio. It appears as a battery base below the target panel which it is a part of as seen
below in FIG. 39.
Target Panel Device #
TDS/WDS
(station version)
NetLinx Studio Online Tree tab
Accessory’s corresponding firmware page
FIG. 39 Location of Firmware version information within NetLinx Studio
The only way to upgrade the firmware of these accessory items is to send the accessory’s firmware
through a target panel. Its this panel’s device number which is entered within the Send to NetLinx Device
transfer dialog in Studio.
Step 1: Prepare the Docking Station for firmware transfer via USB
Before beginning with this section:
ꢀ
ꢀ
Verify the MVP is securely attached to the docking station and communicating properly.
Verify that the panel is communicating from the mini-USB port to the Virtual NetLinx Master
(VNM).
47
MVP-8400i Modero Viewpoint Wireless Touch Panels
Upgrading MVP Firmware
1. Complete the instructions for configuring the NetLinx Master for IP communication found in the
2. After the panel powers-up, press and hold the two lower buttons on both sides of the display for
3 seconds to continue with the setup process and proceed to the Setup page.
Displays the current
docking station firmware version
FIG. 40 Batteries page
The docking station firmware is shown on the right of the Batteries page.
Verify you have downloaded the latest firmware file from www.amx.com and then
save the Kit file to your computer.
Step 2: Upgrade the Docking Station firmware via USB
2. Prepare NetLinx Studio for communication to the panel via a Virtual Master by following the
3. After the Communication Verification dialog window verifies active communication between the
Virtual Master and the panel, click the OnLine Tree tab in the Workspace window to view the
devices on the Virtual System. The default System value is one.
4. Right-click on the System entry and select Refresh System to re-populate the list. Verify the panel
appears in the OnLine Tree tab of the Workspace window.
The default Modero panel value is 10001.
5. Locate the latest firmware file from the www.amx.com > Tech Center > Downloadable Files >
Firmware Files > Modero Panels firmware (MVP Docking Stations: MVP-TDS/WDS) section
of the website.
6. Click on the desired Kit file link and after you’ve accepted the Licensing Agreement, verify you
have downloaded the Docking Station Kit file to a known location.
7. Select Tools > Firmware Transfers > Send to NetLinx Device from the Main menu to open the
match those values listed within the System folder in the OnLine Tree tab of the Workspace
window.
9. Enter the Device number associated with the panel and the System number associated with the
Master (listed in the OnLine Tree tab of the Workspace window). The Port field is greyed-out.
48
MVP-8400i Modero Viewpoint Wireless Touch Panels
Upgrading MVP Firmware
Selected Docking Station Firmware file
Description field for selected Kit file
Firmware download
status
Device and System values
must match the System and Device values
listed in the Project Navigator window
FIG. 41 Send to NetLinx Device dialog (showing docking station firmware update via USB)
Firmware upgrades can not be done directly to the docking station but must be routed
through the MVP panel.
10. Click the Reboot Device checkbox. This causes the touch panel to reboot after the firmware update
process is complete. The reboot of the panel can take up 30 seconds after the firmware process has
finished.
11. Click Send to begin the transfer. The file transfer progress is indicated on the bottom-right of the
dialog.
12. As the panel is rebooting, temporarily unplug the USB connector on the panel until the panel has
completely restarted.
13. Once the first panel page has been displayed, reconnect the USB connector to the panel.
14. Right-click the associated System number and select Refresh System. This causes a refresh of all
project systems, establishes a new connection to the Master, and populates the System list with
devices on your particular system.
15. After the panel powers-up, press and hold the two lower buttons on both sides of the display for
3 seconds to continue with the setup process and proceed to the Setup page.
16. Press the Batteries button (located on the lower-left) to open the Batteries page and confirm the new
firmware does not read 0.00.
If the Base Version field displays 0.00, this means there was an error in the firmware
upload process. Re-install the base firmware and re-confirm that the new base
version no longer reads 0.00.
49
MVP-8400i Modero Viewpoint Wireless Touch Panels
Upgrading MVP Firmware
Although firmware upgrades can be done over wireless Ethernet; it is recommended
that firmware KIT files be transferred over a direct USB connection and only when the
panel is connected to a power supply. If battery power or wireless connection fails
during a firmware upgrade, the panel flash file system may become corrupted.
50
MVP-8400i Modero Viewpoint Wireless Touch Panels
Setup Pages
Setup Pages
AMX Modero panels feature on-board Setup pages. Use the options in the Setup pages to access panel
information and make various configuration changes.
To access the Setup pages, press the two lower external pushbuttons on either side of the panel
simultaneously and hold for 3 seconds (FIG. 42).
Setup Page Access buttons:
Press and hold simultaneously for
3 seconds to access the Setup pages
Press and hold for 6 seconds
to access the Calibration page.
FIG. 42 Setup Page Access buttons
Setup Pages
MVP-7500
MVP-8400
FIG. 43 MVP-7500 and MVP-8400 Setup pages
Features on this page include:
Setup Page
Navigation Buttons:
The buttons along on the left side of the page provide access to secondary Setup
pages (see following sections).
Connection Status icon: The icon in the upper-right corner of each Setup page provides a constant visual
indication of current connection status.
Note: a Lock appears on the icon if the panel is connected to a secured NetLinx
Master.
51
MVP Modero ViewPoint Touch Panels
Setup Pages
Setup Page (Cont.)
Connection Status:
Displays whether the panel is communicating externally as well as the encryption
status of the Master, the connection type (Ethernet or USB), and what System the
panel is connected to.
• Until a connection is established, the message displayed is: “Attempting via...”.
• When a connection is established, the message displayed is either: “Connected
via Ethernet “or “Connected via USB “.
• The word “Encrypted” appears when an encrypted connection is established with
a NetLinx Master.
Note: The panel must be rebooted before incorporating any panel communication
changes and to detect Ethernet connections.
Display Timeout:
Indicates the length of time that the panel can remain idle before activating Sleep
mode (causing the LCD to power down).
• Press the UP/DN buttons to increase/decrease the Display Timeout setting.
Range = 0 - 240 (minutes).
• Set the timeout value to zero to disable Sleep mode.
Note: Small timeout values maximize the life of the battery charge.
Inactivity Page Flip
Timeout:
Indicates the length of time that the panel can remain idle before automatically flip-
ping to a pre-selected page.
• Press the UP/DN buttons to increase/decrease the Inactivity Page Flip Timeout
setting. Range = 0 - 240 (minutes).
• Set the timeout value to zero to disable Inactivity Page Flip mode.
Note: The touch panel page used for the Inactivity page flip is shown within a small
Inactivity Page field.
Panel Brightness:
Sets the display brightness level of the panel.
(MVP-8400 only)
• Press the UP/DN buttons to adjust the brightness level. Range = 0 - 100.
Note: The on-screen bargraph can be dragged to adjust the brightness level which
is then reflected as a numeric value in the Panel Brightness field.
LCD Control:
Sets the display brightness and contrast levels of the panel.
(MVP-7500 only)
• Press the Brightness UP/DN buttons to adjust the brightness level.
Range = 0 - 100.
• Press the Contrast UP/DN buttons to adjust the contrast level. Range = 0 - 100.
52
MVP Modero ViewPoint Touch Panels
Setup Pages
Navigation Buttons
Closes the Setup page
Press to access the Project Information page to view properties of the TPD4 project
file currently loaded on the panel.
Press to access the Panel Information page to view panel specific information
such as resolution, memory, etc.
Press to access the Time Adjustment page where you can alter the time and
date settings on the Master.
Press to access the Audio Adjustments page (on the MVP-7500) or the Volume
page (on the MVP-8400) where you can adjust audio parameters on the panel.
Press to access the Protected Setup page for panel calibration and to access
security release passwords and connection settings.
Press to access the access the Batteries page to monitor MVP-BP Power Pack
status in the panel as well as the docking station.
FIG. 44 Setup Page Navigation Buttons
Project Information Page
The Project Information page displays the project properties of the TPDesign4 project file currently
loaded on the panel (FIG. 45).
FIG. 45 Project Information page and corresponding TPD4 project properties tabs
Features on this page include:
53
MVP Modero ViewPoint Touch Panels
Setup Pages
Project Information Page
Back:
Saves all changes and returns to the previous page.
Connection Status icon: The icon in the upper-right corner of each Setup page provides a constant visual
indication of current connection status.
Note: a Lock appears on the icon if the panel is connected to a secured NetLinx
Master.
File Name:
Displays the name of the TPDesign4 project file downloaded to the panel.
Displays the designer information.
Designer ID:
File Revision:
Dealer ID:
Displays the revision number of the file.
Displays the dealer ID number (unique to every dealer and entered in TPD4).
Displays the job name.
Job Name:
Sales Order:
Purchase Order:
AMX IR 38K Port:
Displays the sales order information.
Displays the purchase order information.
Displays the AMX 38 kHz IR channel port used by the IR Emitter on the panel.
• This information is specified in TPD4 (Project Properties > IR Emitters &
Receivers tab).
• For example if you set the AMX IR 38K Port to 7 and then put a button on the
panel with a channel code of 5 and a port of 7, it will trigger the IR code in slot 5
of the AMX IR 38K Port.
AMX IR 455K Port:
IR User Def 1 Port:
Displays the AMX 455 kHz IR channel port used by the IR Emitter on the panel.
Displays the User Defined IR channel port used by the IR Emitter on the panel.
• Note: User Defined ports can be downloaded by the user and are customizable,
whereas the AMX ones are fixed.
IR User Def 2 Port:
Build Number:
Displays the User Defined IR channel port used by the IR Emitter on the panel.
Displays the build number information of the TPD4 software used to create the
project file.
Creation Date:
Revision Date:
Last Save Date:
Blink Rate:
Displays the project creation date.
Displays the last revision date for the project.
Displays the last date the project was saved.
Displays the feedback blink rate, in .10 second increments.
Displays any comments associated to the job (from the TPD4 project file).
Displays the port assignment being used to report Cradle Sensor information.
Job Comments:
Cradle Sensor Port:
Cradle Sensor Channel: Displays the channel assignment being used to report Cradle Sensor information.
The channel is turned on when the panel is docked (in either the TDS or WDS
docking stations.
IR receivers and transmitters on G4 panels share the device address number of the
panel.
54
MVP Modero ViewPoint Touch Panels
Setup Pages
Panel Information Page
The Panel Information page provides detailed panel information (FIG. 46).
FIG. 46 Panel Information page (takes its’ information from the touch panel)
Features on this page include:
Panel Information Page
Back:
Saves all changes and returns to the previous page.
Connection Status icon:
The icon in the upper-right corner of each Setup page provides a constant
visual indication of current connection status.
Note: a Lock appears on the icon if the panel is connected to a secured NetLinx
Master.
Panel Type:
Displays the model of the panel being used.
Firmware Version:
Setup Port:
Displays the version number of the G4 firmware loaded on the panel.
Displays the setup port information (value) being used by the panel.
Displays the high port (port count) value for the panel.
Displays the high address (address count) value for the panel.
Displays the high channel (channel count) value for the panel.
Displays the high level (level count) value being used by the panel.
Displays the specific serial number value assigned to the panel.
Displays the type and version of the Setup pages being used by the panel.
Displays the screen width (in pixels).
High Port:
High Address:
High Channel:
High Level:
Serial Number:
Setup Pages Version:
Screen Width:
• MVP-7500 = 640
• MVP-8400 = 800
Screen Height:
Displays the screen height (in pixels).
• MVP-7500 = 480 pixels.
• MVP-8400 = 600 pixels.
55
MVP Modero ViewPoint Touch Panels
Setup Pages
Panel Information Page (Cont.)
Screen Refresh Rate:
Displays the video refresh rate applied to the incoming video signal from the
panel.
Screen Rotation:
Power Up Pages:
Start Up String:
Wake Up String:
Sleep String:
File System:
Displays the degree of rotation applied to the on-screen image.
Displays the page assigned to display after the panel is powered-up.
Displays the start-up string.
Displays the wake up string used after an activation from a timeout.
Displays the sleep string used during a panel’s sleep mode.
Displays the amount of Compact Flash memory available on the panel.
Displays the available RAM (or Extended Memory module) on the panel.
RAM:
Time & Date Setup Page
information on the NetLinx Master. If the time and/or date on the Master is modified, all connected
devices will be updated to reflect the new information.
FIG. 47 Time and Date Setup page
MVP touch panels do not have an on-board clock; the only way to modify a panel’s
time without altering the Master is via NetLinx Code.
Features on this page include:
Time & Date Setup Page
Back:
Saves all changes and returns to the previous page.
Connection Status icon: The icon in the upper-right corner of each Setup page provides a constant visual
indication of current connection status.
Note: a Lock appears on the icon if the panel is connected to a secured NetLinx
Master.
56
MVP Modero ViewPoint Touch Panels
Setup Pages
Time & Date Setup Page (Cont.)
Time Date Refresh/Set: This section provides two options:
• The Get Time/Date button retrieves Time and Date information from the Master.
• The Set Time/Date button sets the Master to retain and save any time/date
modifications made on the panel.
Time Display fields:
• These fields display the time in three formats: STANDARD, STANDARD AM/PM,
and 24 HOUR.
Date Display fields:
Set Date/Time:
• These fields display the calendar date information in several different formats.
Use the UP/DN arrow buttons to adjust the Master’s calendar date and time. The
• Year range = 2000 - 2037
• Month range = 1 - 12
• Day range = 1 - 31
• Hour = 24-hour military
• Minute range = 0 - 59
• Second range = 0 - 59
Audio Adjustments/Volume Page
The MVP-7500 and MVP-8400 have different audio features, as reflected in their audio settings pages
ꢀ The MVP-7500 provides an Audio Adjustments page with options that allow you to set Default
Panel Sounds.
ꢀ
The MVP-8400 provides a Volume page with options that allow you to adjust volume levels
and set panel sounds.
MVP-7500 Audio Adjustments page
MVP-8400 Volume page
FIG. 48 Audio Adjustments/Volume pages
Features on these pages include:
Volume Page
Back:
Saves all changes and returns to the previous page.
Connection Status icon:
The icon in the upper-right corner of each Setup page provides a constant
visual indication of current connection status.
Note: a Lock appears on the icon if the panel is connected to a secured NetLinx
Master.
57
MVP Modero ViewPoint Touch Panels
Setup Pages
Volume Page (Cont.)
Master Volume:
This section allows you to alter the current master volume level:
• Use the UP/DN buttons to adjust the volume level (range = 0 - 100).
• The Master Volume bargraph indicates the current volume level.
• The Mute button toggles the Mute feature.
Default Panel Sounds:
Internal Sound Level:
• Activating the Button Hit button plays a default sound when you touch an
active button.
• Activating the Button Miss button plays a default sound when you touch a
non-active button or any area outside of the active button
• The Play Test Sound button plays a test WAV/MP3 file over the panel’s
internal speakers.
Adjusts the volume level on the panel’s internal speaker:
• Use the UP/DN buttons to adjust the volume (range = 0 - 100)
• The Internal Sound Level bargraph indicates the current sound level
• The Mute button mutes the internal speaker volume
Intercom Mic Level:
Adjusts the volume level on the panel’s microphone
• Use the UP/DN buttons to adjust the microphone level (range = 0 - 100)
• The Mic Out Level bargraph indicates the current Mic Out level
Sets the volume level for intercom calls (from another MVP-8400)
• Use the UP/DN buttons to adjust the Line-In volume level (range = 0 - 100)
• The Line-In Level bargraph indicates the current Line-In level
• The Mute button mutes the Line-In volume
Intercom Sound Level:
WAV files - Supported sample rates
The following sample rates for WAV files are supported by MVP-8400 panels:
Supported WAV Sample Rates
• 48000 Hz
• 44100 Hz
• 32000 Hz
• 24000 Hz
• 22050 Hz
• 16000 Hz
• 12000 Hz
• 11025 Hz
• 8000 Hz
58
MVP Modero ViewPoint Touch Panels
Setup Pages
Batteries Page
The options on this page allow you to set power warning preferences, monitor battery status information,
and adjust the display times for battery warnings. This page is populated with information from MVP-
BP batteries in the panel, as well as batteries in a connected MVP-TDS/WDS docking station (FIG. 49).
FIG. 49 Batteries page
Features on this page include:
Batteries Page
Back:
Saves all changes and returns to the previous page.
Connection Status icon:
The icon in the upper-right corner of each Setup page provides a constant
visual indication of current connection status.
Note: a Lock appears on the icon if the panel is connected to a secured NetLinx
Master.
Battery Power Brightness The DISABLE/DISABLED button acts as a power save feature with two options:
Limit:
• Disable - activates the brightness limit set on the panel (conserves battery
power). Activating this feature causes the panel to function at 80% of full
brightness and overrides the Panel Brightness value set on the Setup page.
• Disabled - deactivates this power save feature. The panel will use the Panel
Brightness level.
Note: This field applies to MVP-BP batteries installed in the panel.
Panel Shutdown:
This value determines the number of minutes that would need to pass before
the panel automatically shuts-down. Once shutdown, the unit would have to be
restarted. The UP/DN buttons alter the timeout value (in minutes). A value of 0
disables this feature.
Range = 0 - 240, default = 1200 min.
Note: This field applies to MVP-BP batteries installed in the panel.
Low Battery Warning:
The UP/DN buttons adjust the time value (in minutes) available on the battery
(for use) before the panel displays a low battery warning.
Range - 10 - 45, default = 15 min.
Note: This field applies to MVP-BP batteries installed in the panel.
59
MVP Modero ViewPoint Touch Panels
Setup Pages
Batteries Page (Cont.)
Very Low Battery Warning: The UP/DN buttons adjust the time value (in minutes) available on the battery
before the panel displays a very low battery warning (indicating near-term panel
shutdown).
• Range = 3 - 15, default = 5 min.
• This value cannot exceed the Low Battery Warning value.
Note: This field applies to MVP-BP batteries installed in the panel.
Battery Status:
• The Combined Charge Status bargraph indicates the combined power
charge available from batteries installed in the panel.
• The Battery One Charge Status bargraph indicates the power charge
available on the Slot 1 battery (in the panel).
• The Battery Two Charge Status bargraph indicates the power charge
available on the Slot 2 battery (in the panel).
• The Battery Dock 1 Charge Status bargraph indicates the power charge
available on the docking station’s battery #1.
• The Battery Dock 2 Charge Status bargraph indicates the power charge
available on the docking station’s battery #2.
Note: If no batteries are being charged within the docking station’s battery com-
partments, or the MVP is not connected to a docking station; both Battery Dock
Charge Status fields are left blank.
• The Docking Station Version field indicates the firmware version currently
installed on the docking station.
• The Battery Level Port field indicates the port being used to report charge
status levels back to the NetLinx Master (set in TPDesign4).
• The Battery Level field indicates the level being used to report status levels
back to the NetLinx Master (set in TPDesign4).
60
MVP Modero ViewPoint Touch Panels
Setup Pages
Protected Setup Pages
including communication and security settings.
Enter the factory default password (1988) into the password keypad to access this page.
FIG. 50 Protected Setup page showing default values
Features on the Protected Setup page include:
Protected Setup Page
Navigation Buttons:
The buttons along on the left side of the page provide access to secondary Pro-
tected Setup pages (see following sections).
Back:
Saves all changes and returns to the previous page.
Connection Status icon:
The icon in the upper-right corner of each Setup page provides a constant
visual indication of current connection status.
Note: a Lock appears on the icon if the panel is connected to a secured NetLinx
Master.
Device Number:
Options:
Opens a keypad used to view/set the device number of the panel.
• Function Show - toggles the display of the channel port, channel code, level
• Page Tracking - toggles the page tracking function. When enabled, the panel
reports page data to the NetLinx Master.
• Telnet - enables/disables the panel’s telnet server (to allow direct telnet
communication to the panel).
• Front Button Setup Access - activates the two lower buttons on the front of
page 51). The default setting is On.
- Press and hold these buttons for 3 seconds to access the Setup page.
- Press and hold these buttons for 6 seconds to access the Calibration page.
System Recovery:
• Reset System Settings - deletes all of the current configuration parameters
on the panel (including IP Addresses, Device Number assignments,
Passwords, and other presets). This option invokes a Confirmation dialog,
prompting you to confirm your selection before resetting the panel.
61
MVP Modero ViewPoint Touch Panels
Setup Pages
Protected Setup Page (Cont.)
System Recovery (Cont.): • Remove User Pages - allows you remove all TPD4 touch panel pages
currently on the panel, including the pre-installed AMX Demo pages. This
option invokes a Confirmation dialog, prompting you to confirm your selection
before removing the panel pages.
Note that the YES button on the Confirmation dialog is disabled for 5 seconds
as additional protection against accidentally resetting the panel or removing
the panel pages.
Reboot Panel:
Pressing this button causes the panel to reboot after saving any changes.
Docking Station:
• Dock Status - illuminates when the MVP is docked and communicating with
the Docking Station.
• Undock Panel - forces the docking station to release the MVP without
requiring a User Access username or password.
• Disable Docking Station LED - disables the display of the LEDs on the
docking station.
Channel Code
Channel Port
3,132
BUTTON
2,8
3,50
Address Port
Address Code
Level Port
Channel Code
FIG. 51 Function Show example
Protected Setup Navigation Buttons
Protected Setup page is currently active.
Closes the Protected Setup page
Press to access the G4 Web Control page where you can enable or disable remote
display and control of the panel via a web-enabled PC running a VNC client.
Press to access the Passwords Setup page where you can specify firmware
and user access passwords
.
.
Press to access the Calibration page where you can calibrate the panel-
Press to access the Wireless Settings page where you can configure wireless
connection settings.
Press to access the System Settings page where you can configure
communication settings for the NetLinx Master and the panel
FIG. 52 Protected Setup Navigation Buttons
62
MVP Modero ViewPoint Touch Panels
Setup Pages
G4 Web Control Page
An on-board VNC (Virtual Network Computing) server allows the panel to connect to any remote PC
running a VNC client. Once connected, the client can view and control the panel remotely. The options
on this page allow you to enable/disable G4 Web Control functionality(FIG. 53).
FIG. 53 G4 Web Control page
Features on this page include:
G4 Web Control Page
Back:
Saves all changes and returns to the previous page.
Connection Status icon:
The icon in the upper-right corner of each Setup page provides a constant
visual indication of current connection status.
Note: a Lock appears on the icon if the panel is connected to a secured NetLinx
Master.
G4 Web Control Settings: Sets the IP communication values for the touch panel:
Enable/Enabled
The Enable/Enabled button allows you to toggle between the two G4 activation
settings:
• Enable - deactivates G4 Web Control on the panel.
• Enabled - activates G4 Web Control on the panel.
Network Interface Select
Web Control Name
Displays “Wireless” when the panel is communicating via a Wireless Access
Point (WAP).
Use this field to enter a unique alpha-numeric string to be used as the panel’s
display name within the Manage WebControl Connections window of the
NetLinx Security browser window.
Web Control Password
Web Control Port
Use this field to enter the G4 Authentication session password required for
VNC access to the panel.
Enter the number of the port used by the VNC Web Server. Default = 5900.
Maximum Number of
Connections
Displays the maximum number of users that can be simultaneously connected
to this panel via VNC. Default = 1.
Current Connection Count Displays the number of users currently connected to this panel via VNC.
63
MVP Modero ViewPoint Touch Panels
Setup Pages
G4 Web Control Page
G4 Web Control Timeout:
Sets the length of time (in minutes) that the panel can remain idle (no cursor
movements) before the G4 Web Control session is terminated.
• Minimum value = 0 minutes (panel never times out)
• Maximum value = 240 minutes (panel times out after 240 minutes)
instructions on using the G4 Web Control page with the web-based NetLinx Security
application.
Password Setup Page
The options on the Password Setup page allow you to assign the passwords required for users to access
the Protected Setup page, and to release the MVP from a MVP-TDS or MVP-WDS docking station
FIG. 54 Password Setup page
Features on this page include:
Password Setup Page
Back:
Saves all changes and returns to the previous page.
Connection Status icon:
The icon in the upper-right corner of each Setup page provides a constant
visual indication of current connection status.
Note: a Lock appears on the icon if the panel is connected to a secured NetLinx
Master.
In Panel Password
Change:
Accesses the alphanumeric values associated to particular password sets.
• The PASSWORD 1, 2, 3, 4 and 5 (protected) buttons open a keyboard to
enter alphanumeric values associated to the selected password group.
Note: Clearing Password #5 removes the need to enter a password before
accessing the Protected Setup page.
64
MVP Modero ViewPoint Touch Panels
Setup Pages
Password Setup Page (Cont.)
User Access:
Use these buttons to access and modify the user name/password combinations
required for removing the panel from a docking station. The number of user
access passwords on the panel is limited only by the amount of storage mem-
ory available.
Use the UP/DN buttons to scroll through the list of saved User Access user-
names and passwords.
The Enable/Enabled button allows you to toggle between activating or deacti-
vating the MVP panel requirement of a user to enter a pre-defined password
before removing the panel from a connected docking station:
• Enable - does not prompt the user for a password, the docking station just
releases the panel when the security release pushbutton is pressed.
• Enabled - requires that a valid password from the User Access list be entered
before removing a panel from a docking station.
• The Report button enables/disables reporting the panel’s docking status to
the Master.
Calibration Page
This page (FIG. 55) allows you to calibrate the touch panel for accurate button selection.
FIG. 55 Calibration page
ꢀ
Press and hold the two lower button on both sides of the display for 6 seconds to access the
Calibration page (see FIG. 69 on page 141).
ꢀ
Press the crosshairs to calibrate the panel and return to the previous page.
Always calibrate the panel before its initial use, and after downloading new firmware.
In cases where the touch panel calibration is off to a degree that makes it difficult or
impossible to navigate to this page, you can access it via G4 WebControl, so you can
re-calibrate the panel.
65
MVP Modero ViewPoint Touch Panels
Setup Pages
Wireless Settings Page
wireless CF card (802.11b/g), and read the device number assigned to the panel.
FIG. 56 Wireless Settings page (reads from and assigns values to the WAP)
Features on this page include:
Wireless Settings Page
Back:
Saves all changes and returns to the previous page.
Connection Status icon:
The icon in the upper-right corner of each Setup page provides a constant
visual indication of current connection status.
Note: a Lock appears on the icon if the panel is connected to a secured NetLinx
Master.
IP Settings:
Sets the IP communication values for the panel:
DHCP/STATIC
Sets the panel to either DHCP or Static communication modes.
• DHCP - a temporary IP Addresses is assigned to the panel by a DHCP
server.
• Static IP is a permanent IP Address assigned to the panel. If Static IP is
selected, the other IP Settings fields are enabled (below).
IP Address
Subnet Mask
Gateway
Enter the secondary IP address for this panel.
Enter the subnetwork address for this panel.
Enter the gateway address for this panel.
Enter the host name for this panel.
Host Name
Primary DNS
Enter the address of the primary DNS server used by this panel for host name
lookups.
Secondary DNS
Domain
Enter the secondary DNS address for this panel.
Enter a unique name to the panel for DNS look-up.
MAC Address
This unique address identifies the wireless Ethernet card in the panel (read-
only).
66
MVP Modero ViewPoint Touch Panels
Setup Pages
Wireless Settings Page (Cont.)
IP Settings (Cont.):
Active Roaming on
Channels 1,6,11
In high-interference areas, pressing this button allows the device to switch back
and forth between channels 1, 6, and 11 in order to find the best possible
connection.
Transmit Power
In areas where the connection may be dropped regularly if the device’s
broadcast power is less than necessary to maintain the connnection, pressing
this button automatically increases the broadcast strength to 100 percent.
Access Point MAC
Address:
This unique address identifies the Wireless Access Point (WAP) used by this
panel for wireless communication (read-only).
• Site Survey button: Launches the Site Survey page. The options on this page
allow you to detect (“sniff-out”) all WAPs transmitting within range of the
panel’s NXA-WC80211GCF Wi-Fi card (this feature is not available with the
802.11b).
Data displayed on the Site Survey page is categorized by:
- Network Name (SSID) - WAP names
- Channel (RF) - channels currently being used by the WAP
- Security Type - security protocol enabled on the WAP, if detectable
- Signal Strength - None, Poor, Fair, Good, Very Good, and Excellent
- MAC Address - Unique identification of the transmitting Access Point
information on the SIte Survey page.
• When communicating with a NXA- WAP200G, enter the MAC Address
(BSSID) of the target WAP as the Access Point MAC Address. Refer to the
WAP200G Instruction Manual for more information.
Wireless Security:
Sets the wireless security method to be used by the panel to connect to the net-
work. Selecting any of the connection method buttons invokes the relevant con-
figuration page, with options that allow you to define parameters specific to the
selected method of connection.
these security options.
Open (Clear Text)
“Open” security does not utilize any encryption methodology, but requires an
SSID (alpha-numeric) entry. This entry must match the Network Name (SSID)
entry of the target WAP so the panel knows what device it is using to communi-
cate with the network.
Static WEP
WPA-PSK
“Static WEP” security requires that both a target WAP be identified and an
encryption method be implemented prior to establishing communication.
“WPA-PSK” security is designed for environments where is it desirable to use
WPA or WPA2, but an 802.1x authentication server is not available.
PSK connections are more secure than WEP and are simpler to configure since
they implement dynamic keys but share a key between the WAP and the panel
(client).
EAP-PEAP
“EAP-PEAP” security is designed for wireless environments where it is neces-
sary to securely transmit data over a wireless network.
• For information on uploading a certificate file, refer to the AMX Certificate
67
MVP Modero ViewPoint Touch Panels
Setup Pages
Wireless Settings Page (Cont.)
Wireless Security (Cont.):
EAP-TTLS
“EAP-TTLS” security is designed for wireless environments where it is neces-
sary to first have a Radius server directly validate the identity of the client
(panel) before allowing it access to the network.
• For information on uploading a certificate file, refer to the AMX Certificate
EAP-TLS
“EAP-TLS” security is designed for wireless environments where it is necessary
to securely transmit data over a wireless network by adding an additional level
of security protocol via the use of a private key.
• For information on uploading a certificate file, refer to the AMX Certificate
EAP-LEAP
“EAP-LEAP” security is designed for wireless environments where it is not
required to have both a client or server certificate validation scheme in place,
yet necessary to securely transmit data over a wireless network.
EAP-FAST
“EAP-FAST” security is designed for wireless environments where security and
ease of setup are equally desirable.
Site Survey:
The Site Survey tool allows you to detect and view detailed information on all
WAPs within the panel’s communication area. Using this tool, you can select a
WAP to connect to.
using this tool.
RF Link Info:
SSID
These options set communication values for the wireless interface card:
Displays the currently used SSID of the target WAP.
Channel
The RF channel being used for connection to the WAP (read -only).
Link Quality
Displays the quality of the link from the wireless NIC to the Wireless Access
Point (direct sequence spread spectrum) in real time (None, Poor, Fair, Good,
Very Good, and Excellent).
• Even when link quality is at its lowest you still have a connection, and the
ability to transmit and receive data, even if at lower speeds.
Note: “Link Quality” and “Signal Strength” are applicable to RF connections
only. It is possible to have an RF signal to a WAP, but be unable to communi-
cate with it because of either incorrect IP or encryption settings.
Signal Strength
This indicator displays a description of the signal strength from the Wireless
Access Point connection in real time (None, Poor, Fair, Good, Very Good, and
Excellent).
SNR (Signal Noise Ratio) is a measure of the relative strength of a wireless RF
connection. Given this value and the link quality above, you can determine the
noise level component of the SNR. For example, if signal strength is high but
the link quality is low, then the cause of the link degradation is noise. However,
if signal strength is low and link quality is low the cause would simply be signal
strength.
Data Rate
The data rate (in Mbps) at which the panel is currently communicating with the
target WAP.
Note: Data rates for 802.11b communication are: 1, 2, 5.5, and 11 Mbps.
68
MVP Modero ViewPoint Touch Panels
Setup Pages
Wireless Security Page
The options on the Wireless Security page allow you to select from the wireless security methods
supported by the NXA-WC80211GCF Wi-Fi card. These security methods incorporate WPA, WPA2, and
EAP technology (some of which require the upload of unique certificate files to a target panel).
Some encryption and security features may/may not be supported depending on the type of wireless card
being used:
Wireless Security Support
802.11b Wi-Fi CF card: • Open (Clear Text)
• Static WEP (64-bit and 128-bit key lengths)
Note: The WAP Site survey feature is disabled. It is only supported on the 802.11g
card.
802.11g Wi-Fi CF card: • Open (Clear Text)
• Static WEP (64-bit and 128-bit key lengths)
• WPA-PSK
• EAP security (with and without certificates)
• WAP SIte Survey
configuring the panel for wireless network access using the various security options.
802.11b wireless card
802.11g wireless card
Wireless Security pages (each Wi Fi card supports different security features)
69
MVP Modero ViewPoint Touch Panels
Setup Pages
Open (Clear Text) Settings
FIG. 57 Wireless Settings page - Open (Clear Text) Settings
Open security does not utilize any encryption methodology, but requires an SSID (alpha-numeric) entry.
This entry must match the Network Name (SSID) entry of the target WAP so the panel knows what
device it is using to communicate with the network.
Open (Clear Text) Settings
SSID (Service Set Identifier): Opens an on-screen keyboard to enter the SSID name used on the target
WAP.
The SSID is a unique name used by the WAP, and is assigned to all panels
on that network. An SSID is required by the WAP before the panel is permit-
ted to join the network.
• The SSID is case sensitive and must not exceed 32 characters.
• Make sure this setting is the same for all points in your wireless network.
• NXA-WAP200Gs use AMX as their default SSID.
• If this field is left blank, the panel will attempt to connect to the first available
WAP.
Save/Cancel:
• Save - store the new security information, apply changes, and return to the
previous page.
• Cancel - discard changes and return to the previous page.
ꢀ
ꢀ
these security options.
70
MVP Modero ViewPoint Touch Panels
Setup Pages
Static WEP Settings
FIG. 58 Wireless Settings page - Static WEP Settings
Static WEP security requires that both a target WAP be identified and an encryption method be
implemented prior to establishing communication. In addition to providing both Open and Shared
Authentication capabilities, this page also supports Hexadecimal and ASCII keys.
Static WEP Settings
SSID (Service Set Identifier): Opens an on-screen keyboard to enter the SSID name used on the target
WAP.
The SSID is a unique name used by the WAP, and is assigned to all panels
on that network. An SSID is required by the WAP before the panel is permit-
ted to join the network.
• The SSID is case sensitive and must not exceed 32 characters.
• Make sure this setting is the same for all points in your wireless network.
• NXA-WAP200Gs use AMX as their default SSID.
• If this field is left blank, the panel will attempt to connect to the first available
WAP.
WEP 64 / WEP 128:
Cycles through the available encryption options: 64 or 128 Bit Key Size.
“WEP” (Wired Equivalent Privacy) is an 802.11 security protocol designed to
provide wireless security equivalent to wired networks.
• WEP64 enables WEP encryption using a 64 Bit Key Size. All packets are
transmitted with their contents encrypted using the Default WEP Key.
• WEP128 enables WEP encryption using a 128 Bit Key Size. All packets are
transmitted with their contents encrypted using the Default WEP Key.
• If the key is not the correct size, the system will resize it to match the
number of bits required for the WEP encryption mode selected.
71
MVP Modero ViewPoint Touch Panels
Setup Pages
Static WEP Settings (Cont.)
Generate (Passphrase):
This button displays an on-screen keyboard which allows you to enter a pass-
phrase. The panel then automatically generates four WEP keys (compatible
only with Modero panels). Enter these WEP keys into the target WAP.
When working with multiple panels, WEP Keys must be entered into the WAP
for each panel.
• All Modero panels use the same code key generator. Therefore, this
Passphrase generates identical keys on any Modero panel.
• The Passphrase generator is case sensitive.
Note: This Key generator is unique to Modero panels and does not generate
the same keys as non-AMX wireless devices. For example, a Current Key
string generated anywhere else will not match those created on Modero pan-
els.
Default Key:
WEP Keys:
Cycles through the four available WEP key identifiers to select a WEP key to
use. As the Default Key value is altered (through selection) the corresponding
“Current Key” is displayed. Each Current Key corresponds to a WEP key.
This feature is useful for accessing different networks without having to re-
enter that networks’ WEP key. It is also sometimes used to set up a rotating
key schedule to provide an extra layer of security.
This feature provides another level of security by selecting up to four WEP
Keys.
Push any of the four buttons to open an on-screen keyboard. Both ASCII and
HEX keys are supported. Up to four keys can be configured for both.
• An ASCII key utilizes either 5 or 13 ASCII characters
• A HEX key utilizes either 10 or 26 Hexidecimal characters
Press Done to accept any changes and save the new value.
Note: A 64-bit key will be 10 characters in length while a 128-bit key will be
26 characters in length. The length of the key entered determines the level of
WEP encryption employed (64 or 128-bit). 128-bit keys may be used if sup-
ported by the internal wireless card.
Current Key:
Displays the current WEP key in use.
• When working with a single panel and a single WAP, it is recommended that
you manually enter the Current Key from the WAP into the selected WEP
Key.
• When working with a single WAP and multiple panels, it is recommended
that you generate a Current Key using the same passphrase on all panels
and then enter the panel-produced WEP key manually into the Wireless
Access Point.
• Keys may also be examined by touching the key buttons and noting the
keyboard initialization text.
• Use the on-screen keyboard’s Clear button to erase stored key information.
Authentication:
Toggles between the two authentication modes: Open + WEP (broadcast
publicly) or Shared + WEP (encrypted).
• An Open + WEP network allows connections from any client without
authentication.
• A Shared + WEP network requires the client to submit a key which is
shared by the network WAP before it is given permission to associate with
the network. In this case the key is the same as the WEP encryption key.
In either case, if WEP encryption has been enabled, the client will still require
the WEP key to encrypt and decrypt packets in order to communicate with the
network.
Save/Cancel:
• Save - store the new security information, apply changes, and return to the
previous page.
• Cancel - discard changes and return to the previous page.
72
MVP Modero ViewPoint Touch Panels
Setup Pages
ꢀ
ꢀ
these security options.
feature.
WPA-PSK Settings
FIG. 59 Wireless Settings page - WPA-PSK Settings
WPA-PSK security is designed for environments where is it desirable to use WPA or WPA2, but an
802.1x authentication server is not available. PSK connections are more secure than WEP and are
simpler to configure since they implement dynamic keys but share a key between the WAP and the panel
(client).
Using WPA-PSK, the encryption on the WAP could either be WPA or WPA2. The firmware in the panel
will automatically connect to the WAP using the correct encryption. The WPA encryption type is
configured on the WAP, not in the firmware.
WAPs do not display “WPA” or “WPA2” on their configuration screens:
ꢀ
ꢀ
WPA is normally displayed as TKIP.
WPA2 is normally displayed as AES CCMP.
The following fields are required: SSID and Password/Pass Phrase.
ꢀ
ꢀ
ꢀ
Enter the SSID of the WAP.
Enter a pass phrase with a minimum of 8 characters and a maximum of 63.
The exact same pass phrase (including capitalization) must be entered in the access point.
73
MVP Modero ViewPoint Touch Panels
Setup Pages
WPA-PSK Settings
SSID (Service Set Identifier): Opens an on-screen keyboard to enter the SSID name used on the target
WAP.
The SSID is a unique name used by the WAP, and is assigned to all panels
on that network. An SSID is required by the WAP before the panel is permit-
ted to join the network.
• The SSID is case sensitive and must not exceed 32 characters.
• Make sure this setting is the same for all points in your wireless network.
• NXA-WAP200Gs use AMX as their default SSID.
• If this field is left blank, the panel will attempt to connect to the first available
WAP.
Password/Pass Phrase:
Opens an on-screen keyboard to enter a passphrase (password).
• This alpha-numeric string must use a minimum of 8 characters and a
maximum of 63.
• The exact pass phrase string (including capitalization) must be entered on
the target WAP.
Save/Cancel:
• Save - store the new security information, apply changes, and return to the
previous page.
• Cancel - discard changes and return to the previous page.
ꢀ
ꢀ
security options.
tool.
EAP-LEAP Settings
FIG. 60 Wireless Settings page - EAP-LEAP Settings
EAP (Extensible Authentication Protocol) is an Enterprise authentication protocol that can be used in
both wired and wireless network environments. EAP requires the use of an 802.1x Authentication
Server, also known as a Radius server. The configuration fields described below take variable length
strings as inputs. An on-screen keyboard is opened when these fields are selected.
74
MVP Modero ViewPoint Touch Panels
Setup Pages
LEAP (Lightweight Extensible Authentication Protocol) was developed to transmit authentication
information securely in a wireless network environment.
LEAP does not use client (panel) or server (RADIUS) certificates and is therefore one
of the least secure EAP security methods but can be utilized successfully by
implementing sufficiently complex passwords.
EAP-LEAP security is designed for wireless environments where it is not required to have a client or
server certificate validation scheme in place, yet necessary to transmit data securely over a wireless
network.
EAP-LEAP Settings
SSID (Service Set Identifier): Opens an on-screen keyboard to enter the SSID name used on the target
WAP.
The SSID is a unique name used by the WAP, and is assigned to all panels
on that network. An SSID is required by the WAP before the panel is permit-
ted to join the network.
• The SSID is case sensitive and must not exceed 32 characters.
• Make sure this setting is the same for all points in your wireless network.
• NXA-WAP200Gs use AMX as their default SSID.
• With EAP security, the SSID of the WAP must be entered. If it is left blank,
the panel will try to connect to the first access point detected that supports
EAP. However, a successful connection is not guaranteed because the
detected WAP may be connected to a RADIUS server, which may not
support this EAP type and/or have the proper user identities configured.
Identity:
Opens an on-screen keyboard. Enter an EAP Identity string (used by the
panel to identify itself to an Authentication (RADIUS) Server).
Note: This information is similar to a username used to login to a secured
server or workstation. This works in tandem with the Password string which is
similar to the password entered to gain access to a secured workstation. Typ-
ically, this is in the form of a username such as: [email protected].
Password:
Opens an on-screen keyboard. Enter the network password string specified
for the user entered within the Identity field (used by the panel to identify itself
to an Authentication (RADIUS) Server)
Note: This information is similar to the password entered to gain access to a
secured workstation.
Save/Cancel:
• Save - store the new security information, apply changes, and return to the
previous page.
• Cancel - discard changes and return to the previous page.
75
MVP Modero ViewPoint Touch Panels
Setup Pages
FIG. 61 EAP-LEAP sample Cisco System Security page
ꢀ
options.
ꢀ
would like.
EAP-FAST Settings
FIG. 62 Wireless Settings page - EAP-FAST Settings
EAP-FAST (Flexible Authentication via Secure Tunneling) security was designed for wireless
environments where security and ease of setup are equally desirable. EAP-FAST uses a certificate file,
however it can be configured to download the certificate automatically the first time the panel attempts to
76
MVP Modero ViewPoint Touch Panels
Setup Pages
authenticate itself. Automatic certificate downloading is convenient but slightly less secure, since its the
certificate is transferred wirelessly and could theoretically be “sniffed-out”.
EAP-FAST Settings
SSID (Service Set Identifier): Opens an on-screen keyboard to enter the SSID name used on the target
WAP.
The SSID is a unique name used by the WAP, and is assigned to all panels
on that network. An SSID is required by the WAP before the panel is permit-
ted to join the network.
• The SSID is case sensitive and must not exceed 32 characters.
• Make sure this setting is the same for all points in your wireless network.
• NXA-WAP200Gs use AMX as their default SSID.
• With EAP security, the SSID of the WAP must be entered. If it is left blank,
the panel will try to connect to the first access point detected that supports
EAP. However, a successful connection is not guaranteed because the
detected WAP may be connected to a RADIUS server, which may not
support this EAP type and/or have the proper user identities configured.
Identity:
Opens an on-screen keyboard. Enter an EAP Identity string (used by the
panel to identify itself to an Authentication (RADIUS) Server).
Note: This information is similar to a username used to login to a secured
server or workstation. This works in tandem with the Password string which is
similar to the password entered to gain access to a secured workstation. Typ-
ically, this is in the form of a username such as: [email protected].
Anonymous Identity:
Opens an on-screen keyboard. Enter an IT provided alpha-numeric string
which (similar to the username) used as the identity, but that does not repre-
sent a real user.
This information is used as a fictitious name which might be seen by sniffer
programs during the initial connection and setup process between the panel
and the Radius server. In this way the real identity (username) is protected.
Typically, this is in the form of a fictitious username such as: anony-
Password:
Opens an on-screen keyboard. Enter the network password string specified
for the user entered within the Identity field (used by the panel to identify itself
to an Authentication (RADIUS) Server)
Note: This information is similar to the password entered to gain access to a
secured workstation.
Automatic PAC
Provisioning:
This selection toggles PAC (Protected Access Credential) Provisioning -
Enabled (automatic) or Disabled (manual).
• If Enabled is selected, the following PAC File Location field is disabled,
because the search for the PAC file is done automatically.
• If Disabled is selected, the user is required to manually locate a file
containing the PAC shared secret credentials for use in authentication. In
this case, the IT department must create a PAC file and then transfer it into
the panel using the AMX Certificate Upload application.
Note: Even when automatic provisioning is enabled, the PAC certificate is
only downloaded the first time that the panel connects to the RADIUS server.
This file is then saved into the panel's file system and is then reused from
then on. It is possible for the user to change a setting (such as a new Identity)
that would invalidate this certificate.
In that case, the panel must be forced to download a new PAC file.
To do this, set Automatic PAC Provisioning to Disabled and then back to
Enabled. This forces the firmware to delete the old file and request a new
one.
77
MVP Modero ViewPoint Touch Panels
Setup Pages
EAP-FAST Settings (Cont.)
PAC File Location:
This field is used when the previous Automatic PAC Provisioning option has
been Disabled.
• When pressed, the panel displays an on-screen PAC File Location
keyboard which allows you to enter the name of the file containing the PAC
shared secret credentials for use in authentication.
• This field is only valid when the automatic PAC provisioning feature has
been enabled via the previous field.
Save/Cancel:
• Save - store the new security information, apply changes, and return to the
previous page.
• Cancel - discard changes and return to the previous page.
ꢀ
ꢀ
options.
feature.
EAP-PEAP Settings
FIG. 63 Wireless Settings page - EAP-PEAP Settings
PEAP (Protected Extensible Authentication Protocol) was developed as a way to securely transmit
authentication information, such as passwords, over a wireless network environment. PEAP uses only
server-side public key certificates and therefore does not need a client (panel) certificate which makes
the configuration and setup easier.
There are two main versions of the PEAP protocol supported by panel’s DeviceScape Wireless Client:
ꢀ
ꢀ
PEAPv0
PEAPv1
PEAP uses inner authentication mechanisms supported by the DeviceScape Wireless Client, the most
common of which are:
ꢀ
ꢀ
MSCHAPv2 with PEAPv0
GTC with PEAPv1
78
MVP Modero ViewPoint Touch Panels
Setup Pages
EAP-PEAP security is designed for wireless environments where it is necessary to transmit data securely
over a wireless network.
EAP-PEAP Settings
SSID (Service Set Identifier): Opens an on-screen keyboard to enter the SSID name used on the target
WAP.
The SSID is a unique name used by the WAP, and is assigned to all panels
on that network. An SSID is required by the WAP before the panel is permit-
ted to join the network.
• The SSID is case sensitive and must not exceed 32 characters.
• Make sure this setting is the same for all points in your wireless network.
• NXA-WAP200Gs use AMX as their default SSID.
• With EAP security, the SSID of the WAP must be entered. If it is left blank,
the panel will try to connect to the first access point detected that supports
EAP. However, a successful connection is not guaranteed because the
detected WAP may be connected to a RADIUS server, which may not
support this EAP type and/or have the proper user identities configured.
Identity:
Opens an on-screen keyboard. Enter an EAP Identity string (used by the
panel to identify itself to an Authentication (RADIUS) Server).
Note: This information is similar to a username used to login to a secured
server or workstation. This works in tandem with the Password string which is
similar to the password entered to gain access to a secured workstation. Typ-
ically, this is in the form of a username such as: [email protected].
Password:
Opens an on-screen keyboard. Enter the network password string specified
for the user entered within the Identity field (used by the panel to identify itself
to an Authentication (RADIUS) Server)
Note: This information is similar to the password entered to gain access to a
secured workstation.
Certificate Authority:
When pressed, the panel displays an on-screen Certificate Authority (CA)
File Location keyboard which allows you to enter the name of the certificate
authority file which is used to validate the server certificate.
This field is optional.
If a server certificate is used, it should first be downloaded into the panel and
the Certificate Authority field should then be set to the name of that certificate
file. No file path should be used for this setting as all certificates are stored in
a specific directory that the user cannot control or change.
• Use the on-screen keyboard’s Clear button to completely erase any
previously stored network path information.
PEAP Version:
When pressed, this field cycles through the choices of available PEAP:
PEAPv0, PEAPv1, or PEAPv1 w/peaplabel=1.
Inner Authentication Type:
When pressed, this field cycles through the choices of available Inner
Authentication mechanisms supported by the Devicescape Secure Wireless
Client. The most commonly used are: MSCHAPv2 and GTC.
• MSCHAPv2 (used with PEAPv0)
• TLS
• GTC (used with PEAPv1)
• OTP
• MD5-Challenge
Save/Cancel:
• Save - store the new security information, apply changes, and return to the
previous page.
• Cancel - discard changes and return to the previous page.
ꢀ
options.
79
MVP Modero ViewPoint Touch Panels
Setup Pages
ꢀ
feature.
EAP-TTLS Settings
FIG. 64 Wireless Settings page - EAP-TTLS Settings
TTLS (EAP Tunneled Transport Layer Security) is an authentication method that does not use a client
certificate to authenticate the panel. However. this method is more secure than PEAP because it does not
broadcast the identity of the user. Setup is similar to PEAP, but differs in the following areas:
ꢀ
An anonymous identity must be specified until the secure tunnel between the panel and the
Radius server is setup to transfer the real identity of the user.
ꢀ
ꢀ
There is no end-user ability to select from the different types of PEAP.
Additional Inner Authentication choices are available to the end-user.
EAP-TTLS security is designed for wireless environments where it is necessary to have the Radius
server directly validate the identity of the client (panel) before allowing it access to the network. This
validation is done by tunneling a connection through the WAP and directly between the panel and the
Radius server. Once the client is identified and then validated, the Radius server disconnects the tunnel
and allows the panel to access the network directly via the target WAP.
EAP-TTLS Settings
SSID (Service Set Identifier): Opens an on-screen keyboard to enter the SSID name used on the target
WAP.
The SSID is a unique name used by the WAP, and is assigned to all panels
on that network. An SSID is required by the WAP before the panel is permit-
ted to join the network.
• The SSID is case sensitive and must not exceed 32 characters.
• Make sure this setting is the same for all points in your wireless network.
• NXA-WAP200Gs use AMX as their default SSID.
• With EAP security, the SSID of the WAP must be entered. If it is left blank,
the panel will try to connect to the first access point detected that supports
EAP. However, a successful connection is not guaranteed because the
detected WAP may be connected to a RADIUS server, which may not
support this EAP type and/or have the proper user identities configured.
80
MVP Modero ViewPoint Touch Panels
Setup Pages
EAP-TTLS Settings (Cont.)
Identity:
Opens an on-screen keyboard. Enter an EAP Identity string (used by the
panel to identify itself to an Authentication (RADIUS) Server).
Note: This information is similar to a username used to login to a secured
server or workstation. This works in tandem with the Password string which is
similar to the password entered to gain access to a secured workstation. Typ-
ically, this is in the form of a username such as: [email protected].
Anonymous Identity:
Opens an on-screen keyboard. Enter an IT provided alpha-numeric string
which (similar to the username) used as the identity, but that does not repre-
sent a real user.
This information is used as a fictitious name which might be seen by sniffer
programs during the initial connection and setup process between the panel
and the Radius server. In this way the real identity (username) is protected.
Typically, this is in the form of a fictitious username such as: anony-
Password:
Opens an on-screen keyboard. Enter the network password string specified
for the user entered within the Identity field (used by the panel to identify itself
to an Authentication (RADIUS) Server)
Note: This information is similar to the password entered to gain access to a
secured workstation.
Certificate Authority:
When pressed, the panel displays an on-screen Certificate Authority (CA)
File Location keyboard which allows you to enter the name of the certificate
authority file which is used to validate the server certificate.
This field is optional.
If a server certificate is used, it should first be downloaded into the panel and
the Certificate Authority field should then be set to the name of that certificate
file. No file path should be used for this setting as all certificates are stored in
a specific directory that the user cannot control or change.
• Use the on-screen keyboard’s Clear button to completely erase any
previously stored network path information.
Inner Authentication Type:
When pressed, this field cycles through the choices of available Inner
Authentication mechanism supported by the Devicescape Secure Wireless
Client:
• MSCHAPv2 (default because its the most common)
• MSCHAP
• PAP
• CHAP
• EAP-MSCHAPv2
• EAP-GTC
• EAP-OTP
• EAP-MD5-Challenge
Save/Cancel:
• Save - store the new security information, apply changes, and return to the
previous page.
• Cancel - discard changes and return to the previous page.
ꢀ
ꢀ
options.
feature.
81
MVP Modero ViewPoint Touch Panels
Setup Pages
EAP-TLS Settings
FIG. 65 Wireless Settings page - EAP-TLS Settings
TLS (Transport Layer Security) was the original standard wireless LAN EAP authentication protocol.
TLS requires additional work during the deployment phase but provides additional security since even a
compromised password is not enough to break into an EAP-TLS protected wireless network
environment.
EAP-TLS security is designed for wireless environments where it is necessary to securely transmit data
over a wireless network by adding an additional level of security protocol via the use of a private key.
EAP-TLS Settings
SSID (Service Set Identifier): Opens an on-screen keyboard to enter the SSID name used on the target
WAP.
The SSID is a unique name used by the WAP, and is assigned to all panels
on that network. An SSID is required by the WAP before the panel is permit-
ted to join the network.
• The SSID is case sensitive and must not exceed 32 characters.
• Make sure this setting is the same for all points in your wireless network.
• NXA-WAP200Gs use AMX as their default SSID.
• With EAP security, the SSID of the WAP must be entered. If it is left blank,
the panel will try to connect to the first access point detected that supports
EAP. However, a successful connection is not guaranteed because the
detected WAP may be connected to a RADIUS server, which may not
support this EAP type and/or have the proper user identities configured.
Identity:
Opens an on-screen keyboard. Enter an EAP Identity string (used by the
panel to identify itself to an Authentication (RADIUS) Server).
Note: This information is similar to a username used to login to a secured
server or workstation. This works in tandem with the Password string which is
similar to the password entered to gain access to a secured workstation. Typ-
ically, this is in the form of a username such as: [email protected].
82
MVP Modero ViewPoint Touch Panels
Setup Pages
EAP-TLS Settings (Cont.)
Certificate Authority:
When pressed, the panel displays an on-screen Certificate Authority (CA)
File Location keyboard which allows you to enter the name of the certificate
authority file which is used to validate the server certificate.
This field is optional.
If a server certificate is used, it should first be downloaded into the panel and
the Certificate Authority field should then be set to the name of that certificate
file. No file path should be used for this setting as all certificates are stored in
a specific directory that the user cannot control or change.
• Use the on-screen keyboard’s Clear button to completely erase any
previously stored network path information.
Client Certificate:
Private Key:
Opens an on-screen keyboard. Enter the name of the file containing the client
(panel) certificate for use in certifying the identity of the client (panel).
Client Certificates and their parameters.
When pressed, the panel displays an on-screen Client Private Key File Loca-
tion keyboard which allows you to enter the name of the file containing the
private key.
• Use the on-screen keyboard’s Clear button to completely erase any
previously stored network path information.
Private Key password:
This field should only be used if the Private Key is protected with a password.
If there is no password protection associated with the Private Key, then this
field should be left blank.
• When pressed, the panel displays an on-screen Private Key Password
keyboard which allows you to enter an alpha-numeric password string.
• Use the on-screen keyboard’s Clear button to completely erase any
previously stored network path information.
Save/Cancel:
• Save - store the new security information, apply changes, and return to the
previous page.
• Cancel - discard changes and return to the previous page.
ꢀ
ꢀ
options.
feature.
Client certificate configuration
There are several ways in which a client certificate can be configured by an IT department. The client
certificate and private key can both be incorporated into one file or split into two separate files. In
addition, the file format used by these files could be PEM, DER, or PKCS12. These formats are
described later in this section. The following table describes how to fill in the fields for each possible
case.
Client Certificate Configuration
Certificate Configuration
Client Certificate Field Private Key Field
Single file contains both the client certificate and
the private key. Format is: PEM or DER.
Enter the file name
Enter the first file name
Leave this field blank
not supported
Enter the same file name
Enter the second file name
Enter the file name
First file contains the client certificate, second file
contains the private key. Format is: PEM or DER.
Single file contains both the client certificate and
the private key. Format is: PKCS12
First file contains the client certificate, second file
not supported
contains the private key. Format is: PKCS12
83
MVP Modero ViewPoint Touch Panels
Setup Pages
AMX supports the following security certificates
ꢀ
ꢀ
ꢀ
PEM (Privacy Enhanced Mail)
DER (Distinguished Encoding Rules)
PKCS12 (Public Key Cryptography Standard #12)
PKCS12 files are frequently generated by Microsoft certificate applications.
Otherwise, PEM is more common.
Certificate files frequently use 5 file extensions. It can be confusing because there is not a one to one
correspondence. The following table shows the possible file extension used for each certificate type:
Certificates and their Extensions
Certificate Type
Possible File Extensions
PEM
.cer
.pem
.pvk
.cer
.der
.pfx
DER
PKCS12
It is important to note which certificate types are supported by the different certificate fields used on the
configuration screens (PEAP, TTLS, and TLS). The following table outlines the firmware fields and their
supported certificate types.
Certificate Types Supported by the Modero Firmware
Configuration Field Name Certificate File Type Supported
Certificate Authority field
Client Certificate field
Private Key field
PEM and DER
PEM and DER
.PEM, DER, and PKCS12
84
MVP Modero ViewPoint Touch Panels
Setup Pages
System Settings Page
FIG. 66 System Settings page
The elements of this page include:
System Settings Page Elements
Back:
Saves all changes and returns to the previous page.
Connection Status icon:
The icon in the upper-right corner of each Setup page provides a constant
visual indication of current connection status.
Note: a Lock appears on the icon if the panel is connected to a secured NetLinx
Master.
Master Connection:
Sets the NetLinx Master communication values:
Type
Sets the NetLinx Master to communicate with the panel via either USB or Ether-
net. This is based on the cable connection from the rear.
Note: ICSNet is not a supported option on this panel.
• Ethernet is a CAT-5 cable (10/100Base T terminated in an RJ-45 connector)
used to network computers together and is used in most LAN (local area
networks). This description is also used to refer to both wired and wireless
communication.
• USB option cannot be used on Modero panels which are not equipped with a
rear USB port.
85
MVP Modero ViewPoint Touch Panels
Setup Pages
Mode
Cycles between the connection modes: URL, Listen, and Auto.
(Ethernet Only - disabled when USB is selected)
• URL - In this mode, enter the IP/URL, Master Port Number, and username/
password (if used) on the Master. The System Number field is read-only - the
panel obtains this information from the Master.
• Listen - In this mode, add the panel address into the URL List in NetLinx
Studio and set the connection mode to Listen. This mode allows the Modero
touch panel to “listen” for the Master’s communication signals. The System
Number and Master IP/URL fields are read-only.
• Auto - In this mode, enter the System Number and a username/password (if
applicable). Use this mode when both the panel and the NetLinx Master are
on the same Subnet, and the Master has its UDP feature enabled. The
Master IP/URL field is read-only.
System Number
Master IP/URL
Allows you to enter a system number. Default value is 0 (zero).
(ETHERNET Only - disabled when USB is selected)
Sets the Master IP or URL of the NetLinx Master.
(ETHERNET Only - disabled when USB is selected)
Allows you to enter the port number used with the NetLinx Master.
• Default = 1319
Master Port Number
(ETHERNET Only - disabled when USB is selected)
Username/Password
If the target Master has been previously secured, enter the alpha-numeric string
(into each field) assigned to a pre-configured user profile on the Master.
This profile should have the pre-defined level of access/configuration rights.
Refer to the Step 3: Choose a Master Connection Mode section on page 31 for more detailed information
on using the System Settings page.
86
MVP Modero ViewPoint Touch Panels
Setup Pages
EAP Security & Server Certificates - Overview
The following EAP types all support a server certificate:
ꢀ
ꢀ
ꢀ
EAP-PEAP
EAP-TTLS
EAP-TLS
All three of these certificate-using security methods are documented in the following sections. EAP
Authentication goes a step beyond just encrypting data transfers, but also requires that a set of
credentials be validated before the client (panel) is allowed to connect to the rest of the network
(FIG. 67). Below is a description of this process. It is important to note that there is no user intervention
necessary during this process. It proceeds automatically based on the configuration parameters entered
into the panel.
LAN
802.1x
(EAP over Wireless)
Authentication Server
Client - Panel
(supplicant)
Authenticator
(Wireless Access Point)
(RADIUS Server)
FIG. 67 EAP security method in process
A server certificate file uses a certificate that is installed in a panel so that the RADIUS server can be
validated before the panel tries to connect to it. The field name associated with this file is Certificate
Authority.
If a server certificate is used, it should first be downloaded into the panel and the Certificate Authority
field should then be set to the name of that certificate file. No file path should be used for this setting as
all certificates are stored in a specific directory that the user cannot control or change. The most secure
connection method uses a server certificate.
If no server certificate will be used then, this field should be left blank. If the field contains a file name,
then a valid certificate file with the same file name must be previously installed on the panel. Otherwise
the authentication process will fail.
87
MVP Modero ViewPoint Touch Panels
Setup Pages
88
MVP Modero ViewPoint Touch Panels
Programming
Programming
Overview
You can program the touch panel, using the commands in this section, to perform a wide variety of
operations using Send_Commands and variable text commands.
A device must first be defined in the NetLinx programming language with values for the Device:
Port: System (in all programming examples - Panel is used in place of these values and represents all
Modero panels).
Verify you are using the latest NetLinx Master and Modero firmware.
Verify you are using the latest version of NetLinx Studio and TPD4.
Button Assignments
• Button Channel Range: 1 - 4000 Button push and Feedback (per address port)
• Button Variable Text range: 1 - 4000 (per address port)
• Button States Range: 1 - 256
(0 = All states, for General buttons 1 = Off state and 2 = On state).
• Level Range: 1 - 600 (Default level value 0 - 255, can be set up to 1 - 65535)
• Address port Range: 1 - 100
These button assignments can only be adjusted in TPD4 and not on the panels
themselves.
Page Commands
These Page Commands are used in NetLinx Programming Language and are case insensitive.
Page Commands
@APG
Add the popup page to a group if it does not already exist. If the new popup is added to a
group which has a popup displayed on the current page along with the new pop-up, the
displayed popup will be hidden and the new popup will be displayed.
Add a specific
popup page to a
specified popup
group.
Syntax:
"'@APG-<popup page name>;<popup group name>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
popup group name = 1 - 50 ASCII characters. Name of the popup group.
Example:
SEND_COMMAND Panel,"'@APG-Popup1;Group1'"
Adds the popup page ’Popup1’ to the popup group ’Group1’.
89
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Page Commands (Cont.)
@CPG
Syntax:
Clear all popup
pages from
specified popup
group.
"'@CPG-<popup group name>'"
Variable:
popup group name = 1 - 50 ASCII characters. Name of the popup group.
Example:
SEND_COMMAND Panel,"'@CPG-Group1'"
Clears all popup pages from the popup group ’Group1’.
Syntax:
@DPG
Delete a specific
popup page from
specified popup
group if it exists.
"'@DPG-<popup page name>;<popup group name>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
popup group name = 1 - 50 ASCII characters. Name of the popup group.
Example:
SEND_COMMAND Panel,"'@DPG-Popup1;Group1'"
Deletes the popup page ’Popup1’ from the popup group ’Group1’.
@PDR
If the flag is set, the popup will return to its default location on show instead of its last drag
location.
Set the popup
location reset flag. Syntax:
"'@PDR-<popup page name>;<reset flag>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed
On.
reset flag = 1 = Enable reset flag
0 = Disable reset flag
Example:
SEND_COMMAND Panel,"'@PDR-Popup1;1'"
Popup1 will return to its default location when turned On.
Syntax:
@PHE
Set the hide effect
for the specified
popup page to the
named hide effect.
"'@PHE-<popup page name>;<hide effect name>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed
On.
hide effect name = Refers to the popup effect names being used.
Example:
SEND_COMMAND Panel,"'@PHE-Popup1;Slide to Left'"
Sets the Popup1 hide effect name to ’Slide to Left’.
@PHP
Only 1 coordinate is ever needed for an effect; however, the command will specify both.
This command sets the location at which the effect will end at.
Set the hide effect
position.
Syntax:
"'@PHP-<popup page name>;<x coordinate>,<y coordinate>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed
On.
Example:
SEND_COMMAND Panel,"'@PHP-Popup1;75,0'"
Sets the Popup1 hide effect x-coordinate value to 75 and the y-coordinate value to 0.
90
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Page Commands (Cont.)
@PHT
Syntax:
Set the hide effect
time for the
specified popup
page.
"'@PHT-<popup page name>;<hide effect time>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed
On.
hide effect time = Given in 1/10ths of a second.
Example:
SEND_COMMAND Panel,"'@PHT-Popup1;50'"
Sets the Popup1 hide effect time to 5 seconds.
@PPA
If the page name is empty, the current page is used. Same as the ’Clear Page’ command
in TPDesign4.
Close all popups
on a specified
page.
Syntax:
"'@PPA-<page name>'"
Variable:
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Panel,"'@PPA-Page1'"
Close all popups on Page1.
@PPF
If the page name is empty, the current page is used (see example 2). If the popup page is
part of a group, the whole group is deactivated. This command works in the same way as
the ’Hide Popup’ command in TPDesign4.
Deactivate a
specific popup
page on either a
specified page or
the current page.
Syntax:
"'@PPF-<popup page name>;<page name>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Panel,"'@PPF-Popup1;Main'"
Example 2:
SEND_COMMAND Panel,"'@PPF-Popup1'"
Deactivates the popup page ’Popup1’ on the current page.
@PPG
If the page name is empty, the current page is used (see example 2). Toggling refers to the
activating/deactivating (On/Off) of a popup page. This command works in the same way
as the ’Toggle Popup’ command in TPDesign4.
Toggle a
specific popup
page on either a
specified page or
the current page.
Syntax:
"'@PPG-<popup page name>;<page name>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Panel,"'@PPG-Popup1;Main'"
Toggles the popup page ’Popup1’ on the ’Main’ page from one state to another (On/Off).
Example 2:
SEND_COMMAND Panel,"'@PPG-Popup1'"
Toggles the popup page ’Popup1’ on the current page from one state to another (On/Off).
91
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Page Commands (Cont.)
@PPK
Kill refers to the deactivating (Off) of a popup window from all pages. If the pop-up page is
part of a group, the whole group is deactivated. This command works in the same way as
the 'Clear Group' command in TPDesign 4.
Kill a specific
popup page from
all pages.
Syntax:
"'@PPK-<popup page name>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
Example:
SEND_COMMAND Panel,"'@PPK-Popup1'"
Kills the popup page ’Popup1’ on all pages.
@PPM
A Modal popup page, when active, only allows you to use the buttons and features on that
popup page. All other buttons on the panel page are inactivated.
Set the modality
of a specific
popup page to
Modal or
Syntax:
"'@PPM-<popup page name>;<mode>'"
Variable:
NonModal.
popup page name = 1 - 50 ASCII characters. Name of the popup page.
mode = NONMODAL converts a previously Modal popup page to a NonModal.
MODAL converts a previously NonModal popup page to Modal.
modal = 1 and non-modal = 0
Example:
SEND_COMMAND Panel,"'@PPM-Popup1;Modal'"
Sets the popup page ’Popup1’ to Modal.
SEND_COMMAND Panel,"'@PPM-Popup1;1'"
Sets the popup page ’Popup1’ to Modal.
@PPN
If the page name is empty, the current page is used (see example 2). If the popup page is
already on, do not re-draw it. This command works in the same way as the ’Show Popup’
command in TPDesign4.
Activate a
specific popup
page to launch on Syntax:
either a specified
"'@PPN-<popup page name>;<page name>'"
page or the
current page.
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Panel,"'@PPN-Popup1;Main'"
Activates ’Popup1’ on the ’Main’ page.
Example 2:
SEND_COMMAND Panel,"'@PPN-Popup1'"
Activates the popup page ’Popup1’ on the current page.
If timeout is empty, popup page will clear the timeout.
Syntax:
@PPT
Set a specific
popup page to
timeout within a
specified time.
"'@PPT-<popup page name>;<timeout>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
timeout = Timeout duration in 1/10ths of a second.
Example:
SEND_COMMAND Panel,"'@PPT-Popup1;30'"
Sets the popup page ’Popup1’ to timeout within 3 seconds.
92
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Page Commands (Cont.)
@PPX
This command works in the same way as the 'Clear All' command in TPDesign 4.
Close all
Syntax:
popups on all
pages.
"'@PPX'"
Example:
SEND_COMMAND Panel,"'@PPX'"
Close all popups on all pages.
@PSE
Syntax:
Set the show
effect for the
specified popup
page to the
named show
effect.
"'@PSE-<popup page name>;<show effect name>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed
On.
show effect name = Refers to the popup effect name being used.
Example:
SEND_COMMAND Panel,"'@PSE-Popup1;Slide from Left'"
Sets the Popup1 show effect name to ’Slide from Left’.
@PSP
Only 1 coordinate is ever needed for an effect; however, the command will specify both.
This command sets the location at which the effect will begin at.
Set the show
effect position.
Syntax:
"'@PSP-<popup page name>;<x coordinate>,<y coordinate>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed
On.
Example:
SEND_COMMAND Panel,"'@PSP-Popup1;100,0'"
Sets the Popup1 show effect x-coordinate value to 100 and the y-coordinate value to 0.
@PST
Syntax:
Set the show
effect time for the
specified popup
page.
"'@PST-<popup page name>;<show effect time>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed
On.
show effect time = Given in 1/10ths of a second.
Example:
SEND_COMMAND Panel,"'@PST-Popup1;50'"
Sets the Popup1 show effect time to 5 seconds.
PAGE
Flips to a page with a specified page name. If the page is currently active, it will not redraw
the page.
Flip to a specified
page.
Syntax:
"'PAGE-<page name>'"
Variable:
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Panel,"'PAGE-Page1'"
Flips to page1.
93
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Page Commands (Cont.)
PPOF
If the page name is empty, the current page is used (see example 2). If the popup page is
part of a group, the whole group is deactivated. This command works in the same way as
the ’Hide Popup’ command in TPDesign4.
Deactivate a
specific popup
page on either a
specified page or
the current page.
Syntax:
"'PPOF-<popup page name>;<page name>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Panel,"'PPOF-Popup1;Main'"
Deactivates the popup page ’Popup1’ on the Main page.
Example 2:
SEND_COMMAND Panel,"'PPOF-Popup1'"
Deactivates the popup page ’Popup1’ on the current page.
PPOG
If the page name is empty, the current page is used (see example 2). Toggling refers to the
activating/deactivating (On/Off) of a popup page. This command works in the same way
as the ’Toggle Popup’ command in TPDesign4.
Toggle a
specific popup
page on either a
specified page or
the current page.
Syntax:
"'PPOG-<popup page name>;<page name>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Panel,"'PPOG-Popup1;Main'"
Toggles the popup page ’Popup1’ on the Main page from one state to another (On/Off).
Example 2:
SEND_COMMAND Panel,"'PPOG-Popup1'"
Toggles the popup page ’Popup1’ on the current page from one state to another (On/Off).
PPON
If the page name is empty, the current page is used (see example 2). If the popup page is
already On, do not re-draw it. This command works in the same way as the ’Show Popup’
command in TPDesign4.
Activate a
specific popup
page to launch on Syntax:
either a specified
"'PPON-<popup page name>;<page name>'"
page or the
current page.
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Panel,"'PPON-Popup1; Main'"
Activates the popup page ’Popup1’ on the Main page.
Example 2:
SEND_COMMAND Panel,"'PPON-Popup1'"
Activates the popup page ’Popup1’ on the current page.
94
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Programming Numbers
The following information provides the programming numbers for colors, fonts, and borders.
Colors can be used to set the colors on buttons, sliders, and pages. The lowest color number represents
the lightest color-specific display; the highest number represents the darkest display. For example, 0
represents light red, and 5 is dark red.
RGB triplets and names for basic 88 colors
RGB Values for all 88 Basic Colors
Index No. Name
Very Light Red
Red
255
223
191
159
127
95
255
223
191
159
127
95
255
223
191
159
127
95
128
112
96
80
64
48
0
Green
0
Blue
0
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
Light Red
0
0
Red
0
0
Medium Red
Dark Red
0
0
0
0
Very Dark Red
Very Light Orange
Light Orange
Orange
0
0
128
112
96
0
0
0
Medium Orange
Dark Orange
Very Dark Orange
Very Light Yellow
Light Yellow
Yellow
80
0
64
0
48
0
255
223
191
159
127
95
0
0
0
Medium Yellow
Dark Yellow
Very Dark Yellow
Very Light Lime
Light Lime
0
0
0
255
223
191
159
127
95
0
0
Lime
0
Medium Lime
Dark Lime
0
0
Very Dark Lime
Very Light Green
Light Green
Green
0
255
223
191
159
127
95
0
0
0
0
0
Medium Green
Dark Green
Very Dark Green
Very Light Mint
Light Mint
0
0
0
0
0
0
0
255
223
191
159
127
95
128
112
96
80
64
48
0
Mint
0
Medium Mint
Dark Mint
0
0
Very Dark Mint
0
95
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
RGB Values for all 88 Basic Colors (Cont.)
Index No. Name
Very Light Cyan
Red
Green
255
223
191
159
127
95
128
112
96
80
64
48
0
Blue
255
223
191
159
127
95
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
0
Light Cyan
Cyan
0
0
Medium Cyan
Dark Cyan
Very Dark Cyan
Very Light Aqua
Light Aqua
Aqua
0
0
0
0
255
223
191
159
127
95
0
0
Medium Aqua
Dark Aqua
Very Dark Aqua
Very Light Blue
Light Blue
0
0
0
0
255
223
191
159
127
95
0
0
Blue
0
0
Medium Blue
Dark Blue
0
0
0
0
Very Dark Blue
Very Light Purple
Light Purple
Purple
0
0
128
112
96
80
64
48
255
223
191
159
127
95
255
223
191
159
127
95
255
238
204
170
136
102
187
153
0
255
223
191
159
127
95
0
0
Medium Purple
Dark Purple
Very Dark Purple
Very Light Magenta
Light Magenta
Magenta
0
0
0
0
255
223
191
159
127
95
0
0
Medium Magenta
Dark Magenta
Very Dark Magenta
Very Light Pink
Light Pink
0
0
0
0
128
112
96
0
Pink
0
Medium Pink
Dark Pink
0
80
0
64
Very Dark Pink
White
0
48
255
238
204
170
136
102
187
153
255
238
204
170
136
102
187
153
Grey1
Grey3
Grey5
Grey7
Grey9
Grey4
Grey6
96
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
RGB Values for all 88 Basic Colors (Cont.)
Index No. Name
Red
Green
119
85
Blue
119
85
80
81
82
83
84
85
86
87
255
Grey8
119
85
51
34
221
68
17
0
Grey10
Grey12
Grey13
Grey2
51
51
34
34
221
68
221
68
Grey11
Grey14
Black
17
17
0
0
TRANSPARENT
99
53
99
Font styles and ID numbers
Font styles can be used to program the text fonts on buttons, sliders, and pages. The following chart
shows the default font type and their respective ID numbers generated by TPDesign4.
Default Font Styles and ID Numbers
Font ID Font type
#
Size
Font ID Font type
#
Size
1
Courier New
Courier New
Courier New
Courier New
Courier New
Courier New
Courier New
Courier New
AMX Bold
9
19
20
21
22
23
24
25
26
27
28
29
Arial
9
2
12
18
26
32
18
26
34
14
20
36
Arial
10
12
14
16
18
20
24
36
10
8
3
Arial
4
Arial
5
Arial
6
Arial
7
Arial
8
Arial
9
Arial
10
11
AMX Bold
Arial Bold
Arial Bold
AMX Bold
32 - Variable Fonts start at 32.
You must import fonts into a TPDesign4 project file. The font ID numbers are
assigned by TPDesign4. These values are also listed in the
Generate Programmer’s Report.
97
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Border styles and Programming numbers
Border styles can be used to program borders on buttons, sliders, and popup pages.
Border Styles and Programming Numbers
No.
0-1
2
Border styles
No border
Single line
Double line
Quad line
No.
Border styles
10-11 Picture frame
12
20
21
Double line
Bevel-S
3
4
Bevel-M
5-6
7
Circle 15
22-23 Circle 15
Single line
Double line
Quad line
24-27 Neon inactive-S
40-41 Diamond 55
8
9
The TPDesign4 Touch Panel Design program has pre-set border styles that are user selectable.
You cannot use the following number values for programming purposes when changing border styles.
TPD4 border styles can ONLY be changed by using the name.
TPD4 Border Styles by Name
No.
1
Border styles
None
No.
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Border styles
Circle 155
2
AMX Elite -L
AMX Elite -M
AMX Elite -S
Bevel -L
Circle 165
3
Circle 175
4
Circle 185
5
Circle 195
6
Bevel -M
Cursor Bottom
Cursor Bottom with Hole
Cursor Top
7
Bevel -S
8
Circle 15
9
Circle 25
Cursor Top with Hole
Cursor Left
10
11
12
13
14
15
16
17
18
19
20
21
Circle 35
Circle 45
Cursor Left with Hole
Cursor Right
Cursor Right with Hole
Custom Frame
Diamond 15
Circle 55
Circle 65
Circle 75
Circle 85
Circle 95
Diamond 25
Circle 105
Circle 115
Circle 125
Circle 135
Circle 145
Diamond 35
Diamond 45
Diamond 55
Diamond 65
Diamond 75
98
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
TPD4 Border Styles by Name (Cont.)
No.
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
Border styles
Diamond 85
No.
85
Border styles
Menu Bottom Rounded 65
Menu Bottom Rounded 75
Menu Bottom Rounded 85
Menu Bottom Rounded 95
Menu Bottom Rounded 105
Menu Bottom Rounded 115
Menu Bottom Rounded 125
Menu Bottom Rounded 135
Menu Bottom Rounded 145
Menu Bottom Rounded 155
Menu Bottom Rounded 165
Menu Bottom Rounded 175
Menu Bottom Rounded 185
Menu Bottom Rounded 195
Menu Top Rounded 15
Menu Top Rounded 25
Menu Top Rounded 35
Menu Top Rounded 45
Menu Top Rounded 55
Menu Top Rounded 65
Menu Top Rounded 75
Menu Top Rounded 85
Menu Top Rounded 95
Menu Top Rounded 105
Menu Top Rounded 115
Menu Top Rounded 125
Menu Top Rounded 135
Menu Top Rounded 145
Menu Top Rounded 155
Menu Top Rounded 165
Menu Top Rounded 175
Menu Top Rounded 185
Menu Top Rounded 195
Menu Right Rounded 15
Menu Right Rounded 25
Menu Right Rounded 35
Menu Right Rounded 45
Menu Right Rounded 55
Menu Right Rounded 65
Menu Right Rounded 75
Menu Right Rounded 85
Menu Right Rounded 95
Diamond 95
86
Diamond 105
87
Diamond 115
88
Diamond 125
89
Diamond 135
90
Diamond 145
91
Diamond 155
92
Diamond 165
93
Diamond 175
94
Diamond 185
95
Diamond 195
96
Double Bevel -L
Double Bevel -M
Double Bevel -S
Double Line
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
Fuzzy
Glow-L
Glow-S
Help Down
Neon Active -L
Neon Active -S
Neon Inactive -L
Neon Inactive -S
Oval H 60x30
Oval H 100x50
Oval H 150x75
Oval H 200x100
Oval V 30x60
Oval V 50x100
Oval V 75x150
Oval V 100x200
Picture Frame
Quad Line
Single Line
Windows Style Popup
Windows Style Popup (Status Bar)
Menu Bottom Rounded 15
Menu Bottom Rounded 25
Menu Bottom Rounded 35
Menu Bottom Rounded 45
Menu Bottom Rounded 55
99
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
TPD4 Border Styles by Name (Cont.)
No.
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
Border styles
No.
145
146
147
148
149
150
151
152
153
154
155
Border styles
Menu Right Rounded 105
Menu Right Rounded 115
Menu Right Rounded 125
Menu Right Rounded 135
Menu Right Rounded 145
Menu Right Rounded 155
Menu Right Rounded 165
Menu Right Rounded 175
Menu Right Rounded 185
Menu Right Rounded 195
Menu Left Rounded 15
Menu Left Rounded 25
Menu Left Rounded 35
Menu Left Rounded 45
Menu Left Rounded 55
Menu Left Rounded 65
Menu Left Rounded 75
Menu Left Rounded 85
Menu Left Rounded 95
Menu Left Rounded 105
Menu Left Rounded 115
Menu Left Rounded 125
Menu Left Rounded 135
Menu Left Rounded 145
Menu Left Rounded 155
Menu Left Rounded 165
Menu Left Rounded 175
Menu Left Rounded 185
Menu Left Rounded 195
"^" Button Commands
These Button Commands are used in NetLinx Studio and are case insensitive.
All commands that begin with "^" have the capability of assigning a variable text address range and
button state range. A device must first be defined in the NetLinx programming language with values
for the Device: Port : System (in all programming examples - Panel is used in place of these values).
ꢀ
Variable text ranges allow you to target 1 or more variable text channels in a single
command.
ꢀ Button State ranges allow you to target 1 or more states of a variable text button with a single
command.
ꢀ
"." Character is used for the 'through' notation, also the "&" character is used for the 'And'
notation.
"^" Button Commands
^ANI
Syntax:
Run a button
animation
(in 1/10 second).
"'^ANI-<vt addr range>,<start state>,<end state>,<time>'"
Variable:
variable text address range = 1 - 4000.
start state = Beginning of button state (0= current state).
end state = End of button state.
time = In 1/10 second intervals.
Example:
SEND_COMMAND Panel,"'^ANI-500,1,25,100'"
Runs a button animation at text range 500 from state 1 to state 25 for 10 second.
100
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
"^" Button Commands (Cont.)
^APF
Syntax:
Add page flip
action to a button
if it does not
"'^APF-<vt addr range>,<page flip action>,<page name>'"
Variable:
variable text address range = 1 - 4000.
already exist.
page flip action =
Stan[dardPage] - Flip to standard page
Prev[iousPage] - Flip to previous page
Show[Popup] - Show Popup page
Hide[Popup] - Hide Popup page
Togg[lePopup] - Toggle popup state
ClearG[roup] - Clear popup page group from all pages
ClearP[age] - Clear all popup pages from a page with the
specified page name
ClearA[ll] - Clear all popup pages from all pages
page name = 1 - 50 ASCII characters.
Example:
SEND COMMAND Panel,"'^APF-400,Stan,Main Page'"
Assigns a button to a standard page flip with page name 'Main Page'.
Syntax:
^BAT
Append
non-unicode text.
"'^BAT-<vt addr range>,<button states range>,<new text>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
new text = 1 - 50 ASCII characters.
Example:
SEND_COMMAND Panel,"'^BAT-520,1,Enter City'"
Appends the text 'Enter City' to the button’s OFF state.
^BAU
Same format as ^UNI.
Append
Syntax:
unicode text.
"'^BAU-<vt addr range>,<button states range>,<unicode text>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
unicode text = 1 - 50 ASCII characters. Unicode characters must be entered in Hex
format.
Example:
SEND_COMMAND Panel,"'^BAU-520,1,00770062'"
Appends Unicode text '00770062' to the button’s OFF state.
101
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
"^" Button Commands (Cont.)
^BCB
Only if the specified border color is not the same as the current color.
Set the border
color to the
Note: Color can be assigned by color name (without spaces), number or R,G,B value
(RRGGBB or RRGGBBAA).
specified color.
Syntax:
"'^BCB-<vt addr range>,<button states range>,<color value>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
information.
Example:
SEND_COMMAND Panel,"'^BCB-500.504&510,1,12'"
Sets the Off state border color to 12 (Yellow). Colors can be set by Color Numbers, Color
name, R,G,B,alpha colors (RRGGBBAA) and R, G & B colors values (RRGGBB).
^BCF
Only if the specified fill color is not the same as the current color.
Set the fill color to Note: Color can be assigned by color name (without spaces), number or R,G,B value
the specified
color.
(RRGGBB or RRGGBBAA).
Syntax:
"'^BCF-<vt addr range>,<button states range>,<color value>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
information.
Example:
SEND_COMMAND Panel,"'^BCF-500.504&510.515,1,12'"
SEND_COMMAND Panel,"'^BCF-500.504&510.515,1,Yellow'"
SEND_COMMAND Panel,"'^BCF-500.504&510.515,1,#F4EC0A63''"
SEND_COMMAND Panel,"'^BCF-500.504&510.515,1,#F4EC0A'"
Sets the Off state fill color by color number. Colors can be set by Color Numbers, Color
name, R,G,B,alpha colors (RRGGBBAA) and R, G & B colors values (RRGGBB).
^BCT
Only if the specified text color is not the same as the current color.
Set the text color Note: Color can be assigned by color name (without spaces), number or R,G,B value
to the specified
color.
(RRGGBB or RRGGBBAA).
Syntax:
"'^BCT-<vt addr range>,<button states range>,<color value>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
information.
Example:
SEND_COMMAND Panel,"'^BCT-500.504&510,1,12'"
Sets the Off state border color to 12 (Yellow). Colors can be set by Color Numbers, Color
name, R,G,B,alpha colors (RRGGBBAA) and R, G & B colors values (RRGGBB).
102
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
"^" Button Commands (Cont.)
^BDO
Determines what order each layer of the button is drawn.
Syntax:
Set the button
draw order.
"'^BDO-<vt addr range>,<button states range>,<1-5><1-5><1-5><1-
5><1-5>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
layer assignments = Fill Layer
= 1
Image Layer = 2
Icon Layer = 3
Text Layer = 4
Border Layer = 5
Note: The layer assignments are from bottom to top. The default draw order is 12345.
Example:
SEND_COMMAND Panel,"'^BDO-530,1&2,51432'"
Sets the button’s variable text 530 ON/OFF state draw order (from bottom to top) to
Border, Fill, Text, Icon, and Image.
Example 2:
SEND_COMMAND Panel,"'^BDO-1,0,12345'"
Sets all states of a button back to its default drawing order.
ONLY works on General-type buttons.
^BFB
Set the feedback Syntax:
type of the button.
"'^BFB-<vt addr range>,<feedback type>'"
Variable:
variable text address range = 1 - 4000.
feedback type = (None, Channel, Invert, On (Always on), Momentary, and Blink).
Example:
SEND_COMMAND Panel,"'^BFB-500,Momentary'"
Sets the Feedback type of the button to 'Momentary'.
Syntax:
^BIM
Set the input
mask for the
specified address.
"'^BIM-<vt addr range>,<input mask>'"
Variable:
variable text address range = 1 - 4000.
input mask = Refer to theText Area Input Masking section on page 156 for character
types.
Example:
SEND_COMMAND Panel,"'^BIM-500,AAAAAAAAAA'"
Sets the input mask to ten ’A’ characters, that are required, to either a letter or digit
(entry is required).
103
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
"^" Button Commands (Cont.)
^BLN
The maximum number of lines to remove is 240. A value of 0 will display the incoming
video signal unaffected. This command is used to scale non 4x3 video images into non
4x3 video buttons.
Set the number of
lines removed
equally from the
top and bottom of
a composite video
signal.
Syntax:
"'^BLN-<vt addr range>,<button states range>,<number of lines>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
number of lines = 0 - 240.
Example:
SEND_COMMAND Panel,"'^BLN-500,55'"
Equally removes 55 lines from the top and 55 lines from the bottom of the video button.
^BMC
Note that the source is a single button state. Each state must be copied as a separate
command. The <codes> section represents what attributes will be copied. All codes are
2 char pairs that can be separated by comma, space, percent or just ran together.
Button copy
command.
Copy attributes of Syntax:
the source button
"'^BMC-<vt addr range>,<button states range>,<source
port>,<source address>,<source state>,<codes>'"
to all the
destination
buttons.
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
• source port = 1 - 100.
• source address = 1 - 4000.
• source state = 1 - 256.
codes:
BM - Picture/Bitmap
BR - Border
CB - Border Color
CF - Fill Color
CT - Text Color
EC - Text effect color
EF - Text effect
FT - Font
IC - Icon
JB - Bitmap alignment
JI - Icon alignment
JT - Text alignment
LN - Lines of video removed
OP - Opacity
SO - Button Sound
TX - Text
VI - Video slot ID
WW - Word wrap on/off
Example:
SEND_COMMAND Panel,"'^BMC-425,1,1,500,1,BR'"
or
SEND_COMMAND Panel,"'^BMC-425,1,1,500,1,%BR'"
Copies the OFF state border of button with a variable text address of 500 onto the OFF
state border of button with a variable text address of 425.
104
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
"^" Button Commands (Cont.)
^BMC (Cont.)
Example 2:
SEND_COMMAND Panel,"'^BMC-150,1,1,315,1,%BR%FT%TX%BM%IC%CF%CT'"
Copies the OFF state border, font, Text, bitmap, icon, fill color and text color of the button
with a variable text address of 315 onto the OFF state border, font, Text, bitmap, icon, fill
color and text color of the button with a variable text address of 150.
^BMF
Syntax:
Set any/all button
parameters by
sending
embedded codes
and data.
"'^BMF-<vt addr range>,<button states range>,<data>'"
Variables:
variable text address char array = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
level range = 1 - 600 (level value is 1 - 65535).
data:
’%B<border style>’ = Set the border style name. See theBorder Styles and Programming
’%B’,<border 0-27,40,41> = Set the borer style number. See theBorder Styles and
’%DO<1-5><1-5><1-5><1-5><1-5> = Set the draw order. Listed from bottom to top.
’%F’,<font 1-8,10,11,20-29,32-xx> = Set the font. See theDefault Font Styles and ID
’%F<font 01-08,10,11,20-29,32-xx>’ = Set the font. See theDefault Font Styles and ID
more information.
’%T<text >’ = Set the text using ASCII characters (empty is clear).
’%P<bitmap>’ = Set the picture/bitmap filename (empty is clear).
’%I’,<icon 01-9900, 0-clear>’ = Set the icon using values of 01 - 9900 (icon numbers are
assigned in the TPDesign4 Resource Manager tab - Slots section).
’%I<icon 01-9900, 0-clear>’ = Set the icon using values of 01 - 9900 (icon numbers are
assigned in the TPDesign4 Resource Manager tab - Slots section).
’%J’,<alignment of text 1-9> = As shown the following telephone keypad alignment
chart:
0
1
4
7
3
6
9
2
5
8
Zero can be used for an absolute position
’%JT<alignment of text 0-9>’ = As shown the above telephone keypad alignment chart,
BUT the 0 (zero) is absolute and followed by ’,<left>,<top>’
’%JB<alignment of bitmap/picture 0-9>’ = As shown the above telephone keypad
alignment chart BUT the 0 (zero) is absolute and followed by ’,<left>,<top>’
’%JI<alignment of icon 0-9>’ = As shown the above telephone keypad alignment chart,
BUT the 0 (zero) is absolute and followed by ’,<left>,<top>’
105
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
"^" Button Commands (Cont.)
^BMF
For some of these commands and values, refer to theRGB Values for all 88 Basic
(Cont.)
’%CF<on fill color>’ = Set Fill Color.
’%CB<on border color>’ = Set Border Color.
’%CT<on text color>’ = Set Text Color.
’%SW<1 or 0>’ = Show/hide a button.
’%ST<style>’ = Button style.
’%SO<sound>’ = Set the button sound.
’%EN<1 or 0>’ = Enable/disable a button.
’%WW<1 or 0>’ = Word wrap ON/OFF.
’%GH<bargraph hi>’ = Set the bargraph upper limit.
’%GL<bargraph low>’ = Set the bargraph lower limit.
’%GN<bargraph slider name>’ = Set the bargraph slider name/Joystick cursor name.
’%GC<bargraph slider color>’ = Set the bargraph slider color/Joystick cursor color.
’%GI<bargraph invert>’ = Set the bargraph invert/noninvert or joystick coordinate
’%GU<bargraph ramp up>’ = Set the bargraph ramp up time in intervals of 1/10 second.
’%GD<bargraph ramp down>’ = Set the bargraph ramp down time in 1/10 second.
’%GG<bargraph drag increment> = Set the bargraph drag increment. Refer to the ^GDI
’%VI<video ON/OFF>’ = Set the Video either ON (value=1) or OFF (value=0).
’%OT<feedback type>’ = Set the Feedback (Output) Type to one of the following:
None, Channel,Invert, ON (Always ON), Momentary, or Blink.
’%SM’ = Submit a text for text area button.
’%SF<1 or 0>’ = Set the focus for text area button.
’%OP<0-255>’ = Set the button opacity to either Invisible (value=0) or Opaque
(value=255).
’%OP#<00-FF>’ = Set the button opacity to either Invisible (value=00) or Opaque
(value=FF).
text format.
more information.
’%EF<text effect name>’ = Set the text effect.
’%EC<text effect color>’ = Set the text effect color.
’%ML<max length>’ = Set the maximum length of a text area.
’%MK<input mask>’ = Set the input mask of a text area.
’%VL<0-1>’ = Log-On/Log-Off the computer control connection
’%VN<network name>’ = Set network connection name.
’%VP<password>’ = Set the network connection password.
Example:
SEND_COMMAND Panel,"'^BMF-500,1,%B10%CFRed%CB Blue
%CTBlack%Ptest.png'"
Sets the button OFF state as well as the Border, Fill Color, Border Color, Text Color, and
Bitmap.
106
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
"^" Button Commands (Cont.)
^BMI
Mask image is used to crop a borderless button to a non-square shape. This is typically
used with a bitmap.
Set the button
mask image.
Syntax:
"'^BMI-<vt addr range>,<button states range>,<mask image>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
mask image = Graphic file used.
Example:
SEND_COMMAND Panel,"'^BMI-530,1&2,newMac.png'"
Sets the button with variable text 530 ON/OFF state mask image to 'newmac.png'.
^BML
If this value is set to zero (0) there is no max length. The maximum length available is
2000. This is only for a Text area input button and not for a Text area input masking button.
Set the maximum
length of the text
area button.
Syntax:
"'^BML-<vt addr range>,<max length>'"
Variable:
variable text address range = 1 - 4000.
max length = 2000 (0=no max length).
Example:
SEND_COMMAND Panel,"'^BML-500,20'"
Sets the maximum length of the text area input button to 20 characters.
Syntax:
^BMP
Assign a picture to "'^BMP-<vt addr range>,<button states range>,<name of bitmap/
those buttons with
a defined address
range.
picture>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
name of bitmap/picture = 1 - 50 ASCII characters.
Example:
SEND_COMMAND Panel,"'^BMP-500.504&510.515,1,bitmap.png'"
Sets the OFF state picture for the buttons with variable text ranges of 500-504 & 510-515.
Syntax:
^BNC
Clear current
TakeNote
annotations.
"'^BNC-<vt addr range>,<command value>'"
Variable:
variable text address range = 1 - 4000.
command value = (0= clear, 1= clear all).
Example:
SEND_COMMAND Panel,"'^BNC-973,0'"
Clears the annotation of the TakeNote button with variable text 973.
107
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
"^" Button Commands (Cont.)
^BNN
Syntax:
Set the TakeNote
network name for
the specified
"'^BNN-<vt addr range>,<network name>'"
Variable:
variable text address range = 1 - 4000.
network name = Use a valid IP Address.
Example:
Addresses.
SEND_COMMAND Panel,"'^BNN-973,192.168.169.99'"
Sets the TakeNote button network name to 192.168.169.99.
Syntax:
^BNT
Set the TakeNote
network port for
the specified
"'^BNT-<vt addr range>,<network port>'"
Variable:
variable text address range = 1 - 4000.
network port = 1 - 65535.
Example:
Addresses.
SEND_COMMAND Panel,"'^BNT-973,5000'"
Sets the TakeNote button network port to 5000.
^BOP
The button opacity can be specified as a decimal between 0 - 255, where zero (0) is
invisible and 255 is opaque, or as a HEX code, as used in the color commands by
preceding the HEX code with the # sign. In this case, #00 becomes invisible and #FF
becomes opaque. If the opacity is set to zero (0), this does not make the button inactive,
only invisible.
Set the button
opacity.
Syntax:
"'^BOP-<vt addr range>,<button states range>,<button opacity>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
button opacity = 0 (invisible) - 255 (opaque).
Example:
SEND_COMMAND Panel,"'^BOP-500.504&510.515,1,200'"
Example 2:
SEND_COMMAND Panel,"'^BOP-500.504&510.515,1,#C8'"
Both examples set the opacity of the buttons with the variable text range of 500-504 and
510-515 to 200.
108
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
"^" Button Commands (Cont.)
^BOR
information.
Set a border to a
specific border
style associated
with a border
value for those
buttons with a
defined address
range.
Syntax:
"'^BOR-<vt addr range>,<border style name or border value>'"
Variable:
variable text address range = 1 - 4000.
border style name = Refer to theBorder Styles and Programming Numbers table on
border value = 0 - 41.
Examples:
SEND_COMMAND Panel,"'^BOR-500.504&510.515,10'"
Sets the border by number (#10) to those buttons with the variable text range of 500-504
& 510-515.
SEND_COMMAND Panel,"'^BOR-500.504&510,AMX Elite -M'"
Sets the border by name (AMX Elite) to those buttons with the variable text range of
500-504 & 510-515.
The border style is available through the TPDesign4 border-style drop-down list. Refer to
^BOS
Syntax:
Set the button to
display either a
Video or
"'^BOS-<vt addr range>,<button states range>,<video state>'"
Variable:
variable text address range = 1 - 4000.
Non-Video
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
window.
video state = Video Off = 0 and Video On = 1.
Example:
SEND_COMMAND Panel,"'^BOS-500,1,1'"
Sets the button to display video.
^BPP
Zero clears the flag.
Set or clear the
protected page flip
flag of a
Syntax:
"'^BPP-<vt addr range>,<protected page flip flag value>'"
Variable:
button.
variable text address range = 1 - 4000.
protected page flip flag value range = 0 - 4 (0 clears the flag).
Example:
SEND_COMMAND Panel,"'^BPP-500,1'"
Sets the button to protected page flip flag 1 (sets it to password 1).
109
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
"^" Button Commands (Cont.)
^BRD
Only if the specified border is not the same as the current border. The border names are
available through the TPDesign4 border-name drop-down list.
Set the border of
a button state/
states.
Syntax:
"'^BRD-<vt addr range>,<button states range>,<border name>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
border name = Refer toBorder Styles and Programming Numbers table on page 98.
Example:
SEND_COMMAND Panel,"'^BRD-500.504&510.515,1&2,Quad Line'"
Sets the border by name (Quad Line) to those buttons with the variable text range of
500-504 & 510-515.
^BSF
Note: Select one button at a time (single variable text address). Do not assign a variable
text address range to set focus to multiple buttons. Only one variable text address can be
in focus at a time.
Set the focus to
the text area.
Syntax:
"'^BSF-<vt addr range>,<selection value>'"
Variable:
variable text address range = 1 - 4000.
selection value = Unselect = 0 and select = 1.
Example:
SEND_COMMAND Panel,"'^BSF-500,1'"
Sets the focus to the text area of the button.
^BSM
This command causes the text areas to send their text as strings to the NetLinx Master.
Submit text for
Syntax:
text area buttons.
"'^BSM-<vt addr range>'"
Variable:
variable text address range = 1 - 4000.
Example:
SEND_COMMAND Panel,"'^BSM-500'"
Submits the text of the text area button.
^BSO
If the sound name is blank the sound is then cleared. If the sound name is not matched,
the button sound is not changed.
Set the sound
played when a
button is pressed.
Syntax:
"'^BSO-<vt addr range>,<button states range>,<sound name>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
sound name = (blank - sound cleared, not matched - button sound not changed).
Example:
SEND_COMMAND Panel,"'^BSO-500,1&2,music.wav'"
Assigns the sound 'music.wav' to the button Off/On states.
110
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
"^" Button Commands (Cont.)
^BVL
Syntax:
Log-On/Log-Off
the computer
control
"'^BVL-<vt addr range>,<connection>'"
Variable:
variable text address range = 1 - 4000.
connection = 0 (Log-Off connection) and 1 (Log-On connection).
Example:
connection.
SEND_COMMAND Panel,"'^BVL-500,0'"
Logs-off the computer control connection of the button.
Syntax:
^BVN
Set the computer
control remote
host for the
SEND_COMMAND <DEV>,"'^BVN-<vt addr range>,<remote host>'"
Variables:
variable text address range = 1 - 4000.
remote host = 1 - 50 ASCII characters.
Example:
specified address.
SEND_COMMAND Panel,"'^BVN-500,191.191.191.191'"
Sets the remote host to '191.191.191.191' for the specific computer control button.
Syntax:
^BVP
Set the network
password for the
specified address.
"'^BVP-<vt addr range>,<network password>'"
Variable:
variable text address range = 1 - 4000.
network password = 1 - 50 ASCII characters.
Example:
SEND_COMMAND Panel,"'^BVP-500,PCLOCK'"
Sets the password to PCLOCK for the specific PC control button.
Syntax:
^BVT
Set the computer
control network
port for the
"'^BVT-<vt addr range>,<network port>'"
Variable:
variable text address range = 1 - 4000.
network port = 1 - 65535.
Example:
specified address.
SEND_COMMAND Panel,"'^BVT-500,5000'"
Sets the network port to 5000.
^BWW
By default, word-wrap is Off.
Set the button
word wrap
Syntax:
"'^BWW-<vt addr range>,<button states range>,<word wrap>'"
feature to those
buttons with a
defined address
range.
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
word wrap = (0=Off and 1=On). Default is Off.
Example:
SEND_COMMAND Panel,"'^BWW-500,1,1'"
Sets the word wrap on for the button’s Off state.
111
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
"^" Button Commands (Cont.)
^CPF
Syntax:
Clear all page flips "'^CPF-<vt addr range>'"
from a button.
Variable:
variable text address range = 1 - 4000.
Example:
SEND_COMMAND Panel,"'^CPF-500'"
Clears all page flips from the button.
^DLD
Syntax:
Set the disable
cradle LED flag.
"'^DLD-<status>'"
Variable:
status = (0= cradle operates normally, 1= forces the cradle LEDs to always be dim).
Example:
SEND_COMMAND Panel,"'^DLD-1'"
Disables the cradle LEDs.
^DPF
Syntax:
Delete page flips
from button if it
already exists.
"'^DFP-<vt addr range>,<actions>,<page name>'"
Variable:
variable text address range = 1 - 4000.
actions =
Stan[dardPage] - Flip to standard page
Prev[iousPage] - Flip to previous page
Show[Popup] - Show Popup page
Hide[Popup] - Hide Popup page
Togg[lePopup] - Toggle popup state
ClearG[roup] - Clear popup page group from all pages
ClearP[age] - Clear all popup pages from a page with the
specified page name
ClearA[ll] - Clear all popup pages from all pages
page name = 1 - 50 ASCII characters.
Example:
SEND COMMAND Panel,"'^DPF-409,Prev'"
Deletes the assignment of a button from flipping to a previous page.
Syntax:
^ENA
Enable or
disable buttons
with a set
variable text
range.
"'^ENA-<vt addr range>,<command value>'"
Variable:
variable text address range = 1 - 4000.
command value = (0= disable, 1= enable)
Example:
SEND_COMMAND Panel,"'^ENA-500.504&510.515,0'"
Disables button pushes on buttons with variable text range 500-504 & 510-515.
112
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
"^" Button Commands (Cont.)
^FON
Font ID numbers are generated by the TPDesign4 programmers report.
Syntax:
Set a font to a
specific Font ID
value for those
buttons with a
defined address
range.
"'^FON-<vt addr range>,<button states range>,<font value>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
font value = range = 1 - XXX. Refer to theDefault Font Styles and ID Numbers table on
Example:
SEND_COMMAND Panel,"'^FON-500.504&510.515,1&2,4'"
Sets the font size to font ID #4 for the On and Off states of buttons with the variable text
range of 500-504 & 510-515.
The Font ID is generated by TPD4 and is located in TPD4 through the Main menu.
Panel > Generate Programmer's Report >Text Only Format >Readme.txt.
"^" Button Commands (Cont.)
^GDI
Syntax:
Change the
bargraph drag
increment.
"'^GDI-<vt addr range>,<bargraph drag increment>'"
Variable:
variable text address range = 1 - 4000.
bargraph drag increment = The default drag increment is 256.
Example:
SEND_COMMAND Panel,"'^GDI-7,128'"
Sets the bargraph with variable text 7 to a drag increment of 128.
^GIV
Parameters 1,2, and 3 will cause a bargraph or slider to be inverted regardless of
orientation. Their effect will be as described for joysticks.
Invert the
joystick axis to
move the origin to
another corner.
Syntax:
"'^GIV-<vt addr range>,<joystick axis to invert>'"
Variable:
variable text address range = 1 - 4000.
joystick axis to invert = 0 - 3.
0 = Normal
0
2
1
3
1 = Invert horizontal axis
2 = Invert vertical axis
3 = Invert both axis locations
For a bargraph 1 = Invert , 0 = Non Invert
Example:
SEND_COMMAND Panel,"'^GIV-500,3'"
Inverts the joystick axis origin to the bottom right corner.
113
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
"^" Button Commands (Cont.)
^GLH
Syntax:
Change the
bargraph upper
limit.
"'^GLH-<vt addr range>,<bargraph hi>'"
Variable:
variable text address range = 1 - 4000.
bargraph limit range = 1 - 65535 (bargraph upper limit range).
Example:
SEND_COMMAND Panel,"'^GLH-500,1000'"
Changes the bargraph upper limit to 1000.
Syntax:
^GLL
Change the
bargraph lower
limit.
"'^GLL-<vt addr range>,<bargraph low>'"
Variable:
variable text address range = 1 - 4000.
bargraph limit range = 1 - 65535 (bargraph lower limit range).
Example:
SEND_COMMAND Panel,"'^GLL-500,150'"
Changes the bargraph lower limit to 150.
Syntax:
^GRD
Change the
bargraph
ramp-down time
in 1/10th of a
second.
"'^GRD-<vt addr range>,<bargraph ramp down time>'"
Variable:
variable text address range = 1 - 4000.
bargraph ramp down time = In 1/10th of a second intervals.
Example:
SEND_COMMAND Panel,"'^GRD-500,200'"
Changes the bargraph ramp down time to 20 seconds.
Syntax:
^GRU
Change the
bargraph
ramp-up time in
1/10th of a
second.
"'^GRU-<vt addr range>,<bargraph ramp up time>'"
Variable:
variable text address range = 1 - 4000.
bargraph ramp up time = In 1/10th of a second intervals.
Example:
SEND_COMMAND Panel,"'^GRU-500,100'"
Changes the bargraph ramp up time to 10 seconds.
A user can also assign the color by Name and R,G,B value (RRGGBB or RRGGBBAA).
Syntax:
^GSC
Change the
bargraph slider
color or joystick
cursor color.
"'^GSC-<vt addr range>,<color value>'"
Variable:
variable text address range = 1 - 4000.
Example:
SEND_COMMAND Panel,"'^GSC-500,12'"
Changes the bargraph or joystick slider color to Yellow.
114
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
"^" Button Commands (Cont.)
^GSN
Slider names and cursor names can be found in the TPDesign4 slider name and cursor
drop-down list.
Change the
bargraph slider
name or joystick
cursor name.
Syntax:
"'^GSN-<vt addr range>,<bargraph slider name>'"
Variable:
variable text address range = 1 - 4000.
bargraph slider name = See table below.
Bargraph Slider Names:
None
Circle -L
Ball
Precision
Circle -S
Circle -M
Rectangle -L
Windows
Rectangle -S
Rectangle -M
Windows Active
Joystick Cursor Names:
None
Circle
Hand
Target
Ball
Arrow
Crosshairs
Gunsight
Spiral
Metal
View Finder
Example:
SEND_COMMAND Panel,"'^GSN-500,Ball'"
Changes the bargraph slider name or the Joystick cursor name to ’Ball’.
Syntax:
^ICO
Set the icon to a
button.
"'^ICO-<vt addr range>,<button states range>,<icon index>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
icon index range = 0 - 9900 (a value of 0 is clear).
Example:
SEND_COMMAND Panel,"'^ICO-500.504&510.515,1&2,1'"
Sets the icon for On and Off states for buttons with variable text ranges of 500-504 &
510-515.
^IRM
Pulse the given IR channel for onTime in tenths of seconds. Delay offTime in tenths of a
second before the next IR pulse is allowed. ^IRM allows the command itself to specify the
port number. ^IRM is needed because commands programmed on the panel itself can
only be sent to a single port number. (currently this is defined as 1 only).
Set the IR
channel.
Note: The port number of the IR will be the port number assigned in TPD4.
Syntax:
"'^IRM-<port>,<channel>,<onTime>,<offTime>'"
Variable:
port = User-defined port on the device (panel).
channel = 1 - 255 (channel to pulse).
onTime = 1/10th of a second.
offTime = 1/10th of a second.
Example:
SEND_COMMAND Panel,"'^IRM-10,5, 20, 10'"
Sets the port 10 IR channel 5 on time to 1 second and off time to 2 seconds.
115
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
"^" Button Commands (Cont.)
^JSB
The alignment of 0 is followed by ',<left>,<top>'. The left and top coordinates are relative
to the upper left corner of the button.
Set bitmap/
picture alignment Syntax:
using a numeric
"'^JSB-<vt addr range>,<button states range>,<new text
alignment>'"
keypad layout for
those buttons with
a defined address
range.
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
new text alignment = Value of 1- 9 corresponds to the following locations:
0
1
4
7
2
5
8
3
6
9
Zero can be used for an absolute position
Example:
SEND_COMMAND Panel,"'^JSB-500.504&510.515,1&2,1'"
Sets the off/on state picture alignment to upper left corner for those buttons with variable
text ranges of 500-504 & 510-515.
^JSI
The alignment of 0 is followed by ',<left>,<top>'. The left and top coordinates are relative
to the upper left corner of the button.
Set icon
alignment using a Syntax:
numeric keypad
"'^JSI-<vt addr range>,<button states range>,<new icon
alignment>'"
layout for those
buttons with a
defined address
range.
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
new icon alignment = Value of 1 - 9 corresponds to the following locations:
0
1
4
7
3
6
9
2
5
8
Zero can be used for an absolute position
Example:
SEND_COMMAND Panel,"'^JSI-500.504&510.515,1&2,1'"
Sets the Off/On state icon alignment to upper left corner for those buttons with variable
text range of 500-504 & 510-515.
116
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
"^" Button Commands (Cont.)
^JST
The alignment of 0 is followed by ',<left>,<top>'. The left and top coordinates are relative
to the upper left corner of the button.
Set text
alignment using a Syntax:
numeric keypad
"'^JST-<vt addr range>,<button states range>,<new text
alignment>'"
layout for those
buttons with a
defined address
range.
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
new text alignment = Value of 1 - 9 corresponds to the following locations:
0
1
4
7
2
5
8
3
6
9
Zero can be used for an absolute position
Example:
SEND_COMMAND Panel,"'^JST-500.504&510.515,1&2,1'"
Sets the text alignment to the upper left corner for those buttons with variable text ranges
of 500-504 & 510-515.
^MBT
Syntax:
Set the Mouse
"'^MBT-<pass data>'"
Button mode On
for the virtual PC.
Variable:
pass data:
0 = None
1 = Left
2 = Right
3 = Middle
Example:
SEND COMMAND Panel,"'^MBT-1'"
Sets the mouse button mode to ’Left Mouse Click’.
^MDC
Syntax:
Turn On the
’Mouse
double-click’
feature for the
virtual PC.
"'^MDC'"
Example:
SEND COMMAND Panel,"'^MDC'"
Sets the mouse double-click for use with the virtual PC.
Syntax:
^SHO
Show or hide a
button with a set
variable text
range.
"'^SHO-<vt addr range>,<command value>'"
Variable:
variable text address range = 1 - 4000.
command value = (0= hide, 1= show).
Example:
SEND_COMMAND Panel,"'^SHO-500.504&510.515,0'"
Hides buttons with variable text address range 500-504 & 510-515.
117
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
"^" Button Commands (Cont.)
^TEC
The Text Effect is specified by name and can be found in TPD4. You can also assign the
color by name or RGB value (RRGGBB or RRGGBBAA).
Set the text effect
color for the
specified
Syntax:
"'^TEC-<vt addr range>,<button states range>,<color value>'"
addresses/states
to the specified
color.
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
Example:
SEND_COMMAND Panel,"'^TEC-500.504&510.515,1&2,12'"
Sets the text effect color to Very Light Yellow on buttons with variable text 500-504
and 510-515.
^TEF
The Text Effect is specified by name and can be found in TPD4.
Set the text effect. Syntax:
"'^TEF-<vt addr range>,<button states range>,<text effect name>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
effect names.
Example:
SEND_COMMAND Panel,"'^TEF-500.504&510.515,1&2,Soft Drop Shadow
3'"
Sets the text effect to Soft Drop Shadow 3 for the button with variable text range 500-504
and 510-515.
^TXT
Sets Non-Unicode text.
Assign a text
string to those
buttons with a
defined address
range.
Syntax:
"'^TXT-<vt addr range>,<button states range>,<new text>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
new text = 1 - 50 ASCII characters.
Example:
SEND_COMMAND Panel,"'^TXT-500.504&510.515,1&2,Test Only'"
Sets the On and Off state text for buttons with the variable text ranges of
500-504 & 510-515.
118
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
"^" Button Commands (Cont.)
^UNI
For the ^UNI command (%UN and ^BMF command), the Unicode text is sent as
ASCII-HEX nibbles.
Set Unicode text.
Syntax:
"'^UNI-<vt addr range>,<button states range>,<unicode text>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
unicode text = Unicode HEX value.
Example:
SEND_COMMAND Panel,"'^UNI-500,1,0041'"
Sets the button’s unicode character to ’A’.
Note: To send the variable text ’A’ in unicode to all states of the variable text
button 1, (for which the character code is 0041 Hex), send the following command:
SEND_COMMAND TP,"'^UNI-1,0,0041'"
Note: Unicode is always represented in a HEX value. TPD4 generates (through the Text
Enter Box dialog) unicode HEX values. Refer to the TPDesign4 Instruction Manual for
more information.
Miscellaneous MVP Strings back to the Master
The following two strings are sent by the MVP panel back to the communicating Master:
MVP Strings to Master
undock <master> This is sent to the target Master when the MVP is undocked.
• If the panel has no information within the User Access Passwords list, ’none’ is sent as
a user.
• If the undock button on the Protected Setup page is used, ’setup’ is sent as a user.
• This string can be disabled from within the firmware setup pages.
dock
This is sent to the target Master when the MVP is docked.
• This string can be disabled from within the firmware setup pages.
MVP Panel Lock Passcode commands
These commands are used to maintain a passcode list. From certain panels a password must be entered to
remove the panel from its cradle. Only the passcode is entered. The user is just for identifying the
passcodes.
MVP Panel Lock Passcode Commands
^LPC
Syntax:
Clear all
"'^LPC'"
users from the
User Access
Passwords list on
the Password
Setup page.
Example:
SEND_COMMAND Panel,"'^LPC'"
Clear all users from the User Access Password list on the Password Setup page.
Refer to thePassword Setup Page section on page 104 for more information.
119
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
MVP Panel Lock Passcode Commands (Cont.)
^LPR
Syntax:
Remove a given
user from the User
Access
Passwords list on
the Password
Setup page.
"'^LPR-<user>'"
Variable:
user = 1 - 50 ASCII characters.
Example:
SEND_COMMAND Panel,"'^LPR-Robert'"
Remove user named ’Robert’ from the User Access Password list on the Password
Setup page. Refer to thePassword Setup Page section on page 104 for more
information.
^LPS
This command allows you to:
Set the user name
and password.
1. Add a new user name and password OR
2. Set the password for a given user.
The user name and password combo is added to the User Access and/or Password list
in the Password Setup page. The user name must be alphanumeric.
Syntax:
"'^LPS-<user>,<passcode>'"
Variable:
user = 1 - 50 ASCII characters.
passcode = 1 - 50 ASCII characters.
Example:
SEND_COMMAND Panel,"'^LPS-Manager,undock'"
Sets a new user name as "Manager" and the password to "undock".
Example 2:
SEND_COMMAND Panel,"'^LPS-Manager,test'"
Changes the given user name password to "test".
Refer to thePassword Setup Page section on page 104 for more information.
Text Effects Names
Text Effects
• Glow -S
• Medium Drop Shadow 1
• Medium Drop Shadow 2
• Medium Drop Shadow 3
• Medium Drop Shadow 4
• Medium Drop Shadow 5
• Medium Drop Shadow 6
• Medium Drop Shadow 7
• Medium Drop Shadow 8
• Hard Drop Shadow 1
• Hard Drop Shadow 2
• Hard Drop Shadow 3
• Hard Drop Shadow 4
• Hard Drop Shadow 5
• Hard Drop Shadow 6
• Hard Drop Shadow 7
• Hard Drop Shadow 8
• Glow -M
• Glow -L
• Glow -X
• Outline -S
• Outline -M
• Outline -L
• Outline -X
• Soft Drop Shadow 1
• Soft Drop Shadow 2
• Soft Drop Shadow 3
• Soft Drop Shadow 4
• Soft Drop Shadow 5
• Soft Drop Shadow 6
• Soft Drop Shadow 7
• Soft Drop Shadow 8
• Medium Drop Shadow 1 with outline • Hard Drop Shadow 1 with outline
• Medium Drop Shadow 2 with outline • Hard Drop Shadow 2 with outline
• Medium Drop Shadow 3 with outline • Hard Drop Shadow 3 with outline
• Medium Drop Shadow 4 with outline • Hard Drop Shadow 4 with outline
• Medium Drop Shadow 5 with outline • Hard Drop Shadow 5 with outline
• Medium Drop Shadow 6 with outline • Hard Drop Shadow 6 with outline
• Medium Drop Shadow 7 with outline • Hard Drop Shadow 7 with outline
• Medium Drop Shadow 8 with outline • Hard Drop Shadow 8 with outline
120
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Text Effects (Cont.)
• Soft Drop Shadow 1 with outline
• Soft Drop Shadow 2 with outline
• Soft Drop Shadow 3 with outline
• Soft Drop Shadow 4 with outline
• Soft Drop Shadow 5 with outline
• Soft Drop Shadow 6 with outline
• Soft Drop Shadow 7 with outline
• Soft Drop Shadow 8 with outline
Button Query Commands
Button Query commands reply back with a custom event. There will be one custom event for each
button/state combination. Each query is assigned a unique custom event type. The following example is
for debug purposes only:
NetLinx Example: CUSTOM_EVENT[device, Address, Custom event type]
DEFINE_EVENT
CUSTOM_EVENT[TP,529,1001]
CUSTOM_EVENT[TP,529,1002]
CUSTOM_EVENT[TP,529,1003]
CUSTOM_EVENT[TP,529,1004]
CUSTOM_EVENT[TP,529,1005]
CUSTOM_EVENT[TP,529,1006]
CUSTOM_EVENT[TP,529,1007]
CUSTOM_EVENT[TP,529,1008]
CUSTOM_EVENT[TP,529,1009]
CUSTOM_EVENT[TP,529,1010]
CUSTOM_EVENT[TP,529,1011]
CUSTOM_EVENT[TP,529,1012]
CUSTOM_EVENT[TP,529,1013]
CUSTOM_EVENT[TP,529,1014]
CUSTOM_EVENT[TP,529,1015]
// Text
// Bitmap
// Icon
// Text Justification
// Bitmap Justification
// Icon Justification
// Font
// Text Effect Name
// Text Effect Color
// Word Wrap
// ON state Border Color
// ON state Fill Color
// ON state Text Color
// Border Name
// Opacity
{
Send_String 0,"'ButtonGet Id=',ITOA(CUSTOM.ID),' Type=',ITOA(CUSTOM.TYPE)"
Send_String 0,"'Flag =',ITOA(CUSTOM.FLAG)"
Send_String 0,"'VALUE1 =',ITOA(CUSTOM.VALUE1)"
Send_String 0,"'VALUE2 =',ITOA(CUSTOM.VALUE2)"
Send_String 0,"'VALUE3 =',ITOA(CUSTOM.VALUE3)"
Send_String 0,"'TEXT
=',CUSTOM.TEXT"
Send_String 0,"'TEXT LENGTH =',ITOA(LENGTH_STRING(CUSTOM.TEXT))"
}
121
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
All custom events have the following 6 fields:
Custom Event Fields
Field
Description
Uint Flag
0 means text is a standard string, 1 means Unicode encoded string
button state number
slong value1
slong value2
slong value3
string text
actual length of string (this is not encoded size)
index of first character (usually 1 or same as optional index
the text from the button
text length (string encode)
button text length
These fields are populated differently for each query command. The text length (String Encode) field is
not used in any command.
Button Query Commands
?BCB
Syntax:
Get the current
border color.
"'?BCB-<vt addr range>,<button states range>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1011:
Flag - zero
Value1 - Button state number
Value2 - Actual length of string (should be 9)
Value3 - Zero
Text - Hex encoded color value (ex: #000000FF)
Text length - Color name length (should be 9)
Example:
SEND COMMAND Panel,"'?BCB-529,1'"
Gets the button 'OFF state' border color. information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1011
Flag = 0
VALUE1 = 1
VALUE2 = 9
VALUE3 = 0
TEXT = #222222FF
TEXT LENGTH = 9
122
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Button Query Commands (Cont.)
?BCF
Syntax:
Get the current fill
color.
"'?BCF-<vt addr range>,<button states range>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1012:
Flag - Zero
Value1 - Button state number
Value2 - Actual length of string (should be 9)
Value3 - Zero
Text - Hex encoded color value (ex: #000000FF)
Text length - Color name length (should be 9)
Example:
SEND COMMAND Panel,"'?BCF-529,1'"
Gets the button 'OFF state' fill color information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1012
Flag = 0
VALUE1 = 1
VALUE2 = 9
VALUE3 = 0
TEXT = #FF8000FF
TEXT LENGTH = 9
?BCT
Syntax:
Get the current
text color.
"'?BCT-<vt addr range>,<button states range>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1013:
Flag - Zero
Value1 - Button state number
Value2 - Actual length of string (should be 9)
Value3 - Zero
Text - Hex encoded color value (ex: #000000FF)
Text length - Color name length (should be 9)
Example:
SEND COMMAND Panel,"'?BCT-529,1'"
Gets the button 'OFF state' text color information.
The result sent to Master would be:
ButtonGet Id = 529 Type = 1013
Flag = 0
VALUE1 = 1
VALUE2 = 9
VALUE3 = 0
TEXT = #FFFFFEFF
TEXT LENGTH = 9
123
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Button Query Commands (Cont.)
?BMP
Syntax:
Get the current
bitmap name.
"'?BMP-<vt addr range>,<button states range>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1002:
Flag - Zero
Value1 - Button state number
Value2 - Actual length of string
Value3 - Zero
Text - String that represents the bitmap name
Text length - Bitmap name text length (should be 9)
Example:
SEND COMMAND Panel,"'?BMP-529,1'"
Gets the button 'OFF state' bitmap information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1002
Flag = 0
VALUE1 = 1
VALUE2 = 9
VALUE3 = 0
TEXT = Buggs.png
TEXT LENGTH = 9
?BOP
Syntax:
Get the overall
button opacity.
"'?BOP-<vt addr range>,<button states range>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1015:
Flag - Zero
Value1 - Button state number
Value2 - Opacity
Value3 - Zero
Text - Blank
Text length - Zero
Example:
SEND COMMAND Panel,"'?BOP-529,1'"
Gets the button 'OFF state' opacity information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1015
Flag = 0
VALUE1 = 1
VALUE2 = 200
VALUE3 = 0
TEXT
=
TEXT LENGTH = 0
124
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Button Query Commands (Cont.)
?BRD
Syntax:
Get the current
border name.
"'?BRD-<vt addr range>,<button states range>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1014:
Flag - Zero
Value1 - Button state number
Value2 - Actual length of string
Value3 - Zero
Text - String that represents border name
Text length - Border name length
Example:
SEND COMMAND Panel,"'?BRD-529,1'"
Gets the button 'OFF state' border information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1014
Flag = 0
VALUE1 = 1
VALUE2 = 22
VALUE3 = 0
TEXT = Double Bevel Raised -L
TEXT LENGTH = 22
?BWW
Syntax:
Get the current
word wrap flag
status.
"'?BWW-<vt addr range>,<button states range>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1010:
Flag - Zero
Value1 - Button state number
Value2 - 0 = no word wrap, 1 = word wrap
Value3 - Zero
Text - Blank
Text length - Zero
Example:
SEND COMMAND Panel,"'?BWW-529,1'"
Gets the button 'OFF state' word wrap flag status information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1010
Flag = 0
VALUE1 = 1
VALUE2 = 1
VALUE3 = 0
TEXT
=
TEXT LENGTH = 0
125
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Button Query Commands (Cont.)
?FON
Syntax:
Get the current
font index.
"'?FON-<vt addr range>,<button states range>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1007:
Flag - Zero
Value1 - Button state number
Value2 - Font index
Value3 - Zero
Text - Blank
Text length - Zero
Example:
SEND COMMAND Panel,"'?FON-529,1'"
Gets the button 'OFF state' font type index information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1007
Flag = 0
VALUE1 = 1
VALUE2 = 72
VALUE3 = 0
TEXT
TEXT LENGTH = 0
Syntax:
=
?ICO
Get the current
icon index.
"'?ICO-<vt addr range>,<button states range>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1003:
Flag - Zero
Value1 - Button state number
Value2 - Icon Index
Value3 - Zero
Text - Blank
Text length - Zero
Example:
SEND COMMAND Panel,"'?ICO-529,1&2'"
Gets the button 'OFF state' icon index information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1003
Flag = 0
VALUE1 = 2
VALUE2 = 12
VALUE3 = 0
TEXT
=
TEXT LENGTH = 0
126
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Button Query Commands (Cont.)
?JSB
Syntax:
Get the current
bitmap
justification.
"'?JSB-<vt addr range>,<button states range>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1005:
Flag - Zero
Value1 - Button state number
Value2 - 1 - 9 justify
Value3 - Zero
Text - Blank
Text length - Zero
Example:
SEND COMMAND Panel,"'?JSB-529,1'"
Gets the button 'OFF state' bitmap justification information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1005
Flag = 0
VALUE1 = 1
VALUE2 = 5
VALUE3 = 0
TEXT
TEXT LENGTH = 0
Syntax:
=
?JSI
Get the current
icon
justification.
"'?JSI-<vt addr range>,<button states range>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1006:
Flag - Zero
Value1 - Button state number
Value2 - 1 - 9 justify
Value3 - Zero
Text - Blank
Text length - Zero
Example:
SEND COMMAND Panel,"'?JSI-529,1'"
Gets the button 'OFF state' icon justification information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1006
Flag = 0
VALUE1 = 1
VALUE2 = 6
VALUE3 = 0
TEXT
=
TEXT LENGTH = 0
127
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Button Query Commands (Cont.)
?JST
Syntax:
Get the current
text justification.
"'?JST-<vt addr range>,<button states range>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1004:
Flag - Zero
Value1 - Button state number
Value2 - 1 - 9 justify
Value3 - Zero
Text - Blank
Text length - Zero
Example:
SEND COMMAND Panel,"'?JST-529,1'"
Gets the button 'OFF state' text justification information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1004
Flag = 0
VALUE1 = 1
VALUE2 = 1
VALUE3 = 0
TEXT
TEXT LENGTH = 0
Syntax:
=
?TEC
Get the current
text effect color.
"'?TEC-<vt addr range>,<button states range>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1009:
Flag - Zero
Value1 - Button state number
Value2 - Actual length of string (should be 9)
Value3 - Zero
Text - Hex encoded color value (ex: #000000FF)
Text length - Color name length (should be 9)
Example:
SEND COMMAND Panel,"'?TEC-529,1'"
Gets the button 'OFF state' text effect color information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1009
Flag = 0
VALUE1 = 1
VALUE2 = 9
VALUE3 = 0
TEXT = #5088F2AE
TEXT LENGTH = 9
128
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Button Query Commands (Cont.)
?TEF
Syntax:
Get the current
text effect name.
"'?TEF-<vt addr range>,<button states range>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1008:
Flag - Zero
Value1 - Button state number
Value2 - Actual length of string
Value3 - Zero
Text - String that represents the text effect name
Text length - Text effect name length
Example:
SEND COMMAND Panel,"'?TEF-529,1'"
Gets the button 'OFF state' text effect name information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1008
Flag = 0
VALUE1 = 1
VALUE2 = 18
VALUE3 = 0
TEXT = Hard Drop Shadow 3
TEXT LENGTH = 18
?TXT
Syntax:
Get the current
text information.
"'?TXT-<vt addr range>,<button states range>,<optional index>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
optional index = This is used if a string was too long to get back in one command.
The reply will start at this index.
custom event type 1001:
Flag - Zero
Value1 - Button state number
Value2 - Actual length of string
Value3 - Index
Text - Text from the button
Text length - Button text length
Example:
SEND COMMAND Panel,"'?TXT-529,1'"
Gets the button 'OFF state' text information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1001
Flag = 0
VALUE1 = 1
VALUE2 = 14
VALUE3 = 1
TEXT = This is a test
TEXT LENGTH = 14
129
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Panel Runtime Operations
Serial Commands are used in the AxcessX Terminal Emulator mode. These commands are case
insensitive.
Panel Runtime Operation Commands
ABEEP
Syntax:
Output a single
beep even if beep
is Off.
"'ABEEP'"
Example:
SEND COMMAND Panel,"'ABEEP'"
Outputs a beep of duration 1 beep even if beep is Off.
Syntax:
ADBEEP
Output a double
beep even if beep
is Off.
"'ADBEEP'"
Example:
SEND COMMAND Panel,"'ADBEEP'"
Outputs a double beep even if beep is Off.
@AKB
Keyboard string is set to null on power up and is stored until power is lost. The Prompt
Text is optional.
Pop up the
keyboard icon and Syntax:
initialize the text
"'@AKB-<initial text>;<prompt text>'"
string to that
specified.
Variables:
initial text = 1 - 50 ASCII characters.
prompt text = 1 - 50 ASCII characters.
Example:
SEND COMMAND Panel,"'@AKB-Texas;Enter State'"
Pops up the Keyboard and initializes the text string 'Texas' with prompt text 'Enter State'.
Keyboard string is set to null on power up and is stored until power is lost.
Syntax:
AKEYB
Pop up the
keyboard icon and
initialize the text
string to that
specified.
"'AKEYB-<initial text>'"
Variables:
initial text = 1 - 50 ASCII characters.
Example:
SEND COMMAND Panel,"'AKEYB-This is a Test'"
Pops up the Keyboard and initializes the text string 'This is a Test'.
The keypad string is set to null on power up and is stored until power is lost.
Syntax:
AKEYP
Pop up the
keypad icon and
initialize the text
string to that
specified.
"'AKEYP-<number string>'"
Variables:
number string = 0 - 9999.
Example:
SEND COMMAND Panel,"'AKEP-12345'"
Pops up the Keypad and initializes the text string '12345'.
AKEYR
Remove keyboard or keypad that was displayed using 'AKEYB', 'AKEYP', 'PKEYP',
@AKB, @AKP, @PKP, @EKP, or @TKP commands.
Remove the
Keyboard/
Keypad.
Syntax:
"'AKEYR'"
Example:
SEND COMMAND Panel,"'AKEYR'"
Removes the Keyboard/Keypad.
130
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Panel Runtime Operation Commands (Cont.)
@AKP
Keypad string is set to null on power up and is stored until power is lost. The Prompt Text
is optional.
Pop up the
keypad icon and
initialize the text
string to that
specified.
Syntax:
"'@AKP-<initial text>;<prompt text>'"
Variables:
initial text = 1 - 50 ASCII characters.
prompt text = 1 - 50 ASCII characters.
Example:
SEND COMMAND Panel,"'@AKP-12345678;ENTER PASSWORD'"
Pops up the Keypad and initializes the text string '12345678' with prompt text ’ENTER
PASSWORD’.
@AKR
Remove keyboard or keypad that was displayed using 'AKEYB', 'AKEYP', 'PKEYP',
@AKB, @AKP, @PKP, @EKP, or @TKP commands.
Remove the
Keyboard/
Keypad.
Syntax:
"'@AKR'"
Example:
SEND COMMAND Panel,"'@AKR'"
Removes the Keyboard/Keypad.
Syntax:
BEEP
Output a beep.
"'BEEP'"
Example:
SEND COMMAND Panel,"'BEEP'"
Outputs a beep.
BRIT
Syntax:
Set the panel
brightness.
"'BRIT-<brightness level>'"
Variable:
brightness level = 0 - 100.
Example:
SEND COMMAND Panel,"'BRIT-50'"
Sets the brightness level to 50.
Syntax:
@BRT
Set the panel
brightness.
"'@BRT-<brightness level>'"
Variable:
brightness level = 0 - 100.
Example:
SEND COMMAND Panel,"'@BRT-70'"
Sets the brightness level to 70.
Syntax:
DBEEP
Output a
"'DBEEP'"
double beep.
Example:
SEND COMMAND Panel,"'DBEEP'"
Outputs a double beep.
131
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Panel Runtime Operation Commands (Cont.)
@EKP
Pops up the keypad icon and initializes the text string to that specified. The Prompt Text is
optional.
Extend the
Keypad.
Syntax:
"'@EKP-<initial text>;<prompt text>'"
Variables:
initial text = 1 - 50 ASCII characters.
prompt text = 1 - 50 ASCII characters.
Example:
SEND COMMAND Panel,"'@EKP-33333333;Enter Password'"
Pops up the Keypad and initializes the text string '33333333' with prompt text 'Enter
Password'.
PKEYP
Pops up the keypad icon and initializes the text string to that specified. Keypad displays a
'*' instead of the numbers typed. The Prompt Text is optional.
Present a private
keypad.
Syntax:
"'PKEYP-<initial text>'"
Variables:
initial text = 1 - 50 ASCII characters.
Example:
SEND COMMAND Panel,"'PKEYP-123456789'"
Pops up the Keypad and initializes the text string '123456789' in '*'.
@PKP
Pops up the keypad icon and initializes the text string to that specified. Keypad displays a
'*' instead of the numbers typed. The Prompt Text is optional.
Present a private
keypad.
Syntax:
"'@PKP-<initial text>;<prompt text>'"
Variables:
initial text = 1 - 50 ASCII characters.
prompt text = 1 - 50 ASCII characters.
Example:
SEND COMMAND Panel,"'@PKP-1234567;ENTER PASSWORD'"
Pops up the Keypad and initializes the text string 'ENTER PASSWORD' in '*'.
SETUP
Syntax:
Send panel to
SETUP page.
"'SETUP'"
Example:
SEND COMMAND Panel,"'SETUP'"
Sends the panel to the Setup Page.
Syntax:
SHUTDOWN
Shut down the
batteriesproviding
power to the
panel.
"'SHUTDOWN'"
Example:
SEND COMMAND Panel,"'SHUTDOWN'"
Shuts-down the batteries feeding power to the panel. This function saves the battery from
discharging.
SLEEP
Syntax:
Force the panel
into screen saver
mode.
"'SLEEP'"
Example:
SEND COMMAND Panel,"'SLEEP'"
Forces the panel into screen saver mode.
132
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Panel Runtime Operation Commands (Cont.)
@SOU
Syntax:
Play a sound file.
"'@SOU-<sound name>'"
Variables:
sound name = Name of the sound file. Supported sound file formats
are: WAV & MP3.
Example:
SEND COMMAND Panel,"'@SOU-Music.wav'"
Plays the 'Music.wav' file.
@TKP
Pops up the keypad icon and initializes the text string to that specified. The Prompt Text is
optional.
Present a
telephone
keypad.
Syntax:
"'@TKP-<initial text>;<prompt text>'"
Variables:
initial text = 1 - 50 ASCII characters.
prompt text = 1 - 50 ASCII characters.
Example:
SEND COMMAND Panel,"'@TKP-999.222.1211;Enter Phone Number'"
Pops-up the Keypad and initializes the text string '999.222.1211' with prompt text 'Enter
Phone Number'.
TPAGEON
This command turns On page tracking, whereby when the page or popups change, a
string is sent to the Master. This string may be captured with a CREATE_BUFFER
command for one panel and sent directly to another panel.
Turn On page
tracking.
Syntax:
"'TPAGEON'"
Example:
SEND COMMAND Panel,"'TPAGEON'"
Turns On page tracking.
Syntax:
TPAGEOFF
Turn Off page
tracking.
"'TPAGEOFF'"
Example:
SEND COMMAND Panel,"'TPAGEOFF'"
Turns Off page tracking.
Syntax:
@VKB
Popup the
virtual
keyboard.
"'@VKB'"
Example:
SEND COMMAND Panel,"'@VKB'"
Pops-up the virtual keyboard.
Syntax:
WAKE
Force the panel
out of screen
saver mode.
"'WAKE'"
Example:
SEND COMMAND Panel,"'WAKE'"
Forces the panel out of the screen saver mode.
133
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Input Commands
These Send Commands are case insensitive.
Input Commands
^CAL
Syntax:
Put panel in
"'^CAL'"
calibration mode.
Example:
SEND COMMAND Panel,"'^CAL'"
Puts the panel in calibration mode.
Syntax:
^KPS
Set the
"'^KPS-<pass data>'"
keyboard
passthru.
Variable:
pass data:
<blank/empty> = Disables the keyboard.
0 = Pass data to G4 application (default). This can be used with VPC or text areas.
1 - 4 = Not used.
5 = Sends out data to the Master.
Example:
SEND COMMAND Panel,"'^KPS-5'"
Sets the keyboard passthru to the Master. Option 5 sends keystrokes directly to the
Master via the Send Output String mechanism. This process sends a virtual keystroke
command (^VKS) to the Master.
Example 2:
SEND COMMAND Panel,"'^KPS-0'"
Disables the keyboard passthru to the Master.
The following point defines how the parameters within this command work:
• Accepts keystrokes from any of these sources: attached USB keyboard or Virtual
keyboard.
^VKS
Key presses and key releases are not distinguished except in the case of CTRL, ALT, and
SHIFT.
Send one or more
virtual key strokes Refer to theEmbedded Codes table on page 135 that define special characters which
to the G4
can be included with the string but may not be represented by the ASCII character set.
application.
Syntax:
"'^VKS-<string>'"
Variable:
string = Only 1 string per command/only one stroke per command.
Example:
SEND COMMAND Panel,"'^VKS-'8"
Sends out the keystroke 'backspace' to the G4 application.
134
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Embedded codes
The following is a list of G4 compatible embedded codes:
Embedded Codes
Decimal numbers Hexidecimal values
Virtual keystroke
8
($08)
($0D)
($1B)
($80)
($81)
($82)
($83)
($84)
($85)
($86)
($87)
($88)
($89)
($8A)
($8B)
($8C)
($8D)
($8E)
($8F)
($90)
($91)
($92)
($93)
($94)
($95)
($96)
($97)
($98)
($99)
($9A)
($9B)
($9C)
($9D)
($9E)
($9F)
($A0)
($A1)
($A2)
($C0)
($C1)
($C2)
Backspace
Enter
13
27
ESC
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
192
193
194
CTRL key down
ALT key down
Shift key down
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
Num Lock
Caps Lock
Insert
Delete
Home
End
Page Up
Page Down
Scroll Lock
Pause
Break
Print Screen
SYSRQ
Tab
Windows
Menu
Up Arrow
Down Arrow
Left Arrow
Right Arrow
CTRL key up
ALT key up
Shift key up
135
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Panel Setup Commands
These commands are case insensitive.
Panel Setup Commands
^MUT
Syntax:
Set the panel
mute state.
"'^MUT-<mute state>'"
Variable:
mute state= 0 = Mute Off and 1 = Mute On.
Example:
SEND_COMMAND Panel,"'^MUT-1''"
Sets the panel’s master volume to mute.
@PWD sets the level 1 password only.
Syntax:
@PWD
Set the page flip
password.
"'@PWD-<page flip password>'"
Variables:
page flip password = 1 - 50 ASCII characters.
Example:
SEND COMMAND Panel,"'@PWD-Main'"
Sets the page flip password to 'Main'.
Password level is required and must be 1 - 4.
Syntax:
^PWD
Set the page flip
password.
"'^PWD-<password level>,<page flip password>'"
Variables:
password level = 1 - 4.
page flip password = 1 - 50 ASCII characters.
Example:
SEND COMMAND Panel,"'^PWD-1,Main'"
Sets the page flip password on Password Level 1 to 'Main'.
@RPP resets the protected password to its default (1988).
Syntax:
@RPP
Reset the
protected
password.
"'@RPP'"
Example:
SEND COMMAND Panel,"'@RPP'"
Resets the protected Setup page password to ‘1988’.
Syntax:
^VOL
Set the panel
volume.
"'^VOL-<volume level>'"
Variable:
volume level = 0 - 100. 100 is maximum volume setting.
Example:
SEND_COMMAND Panel,"'^VOL-50'"
Set the panel volume to 50.
136
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Dynamic Image Commands
The following is a listing and descriptions of Dynamic Image Commands.
Dynamic Image Commands
^BBR
Syntax:
Set the bitmap of
a button to use a
particular
"'^BBR-<vt addr range>,<button states range>,<resource name>'"
Variable:
variable text address range = 1 - 4000.
resource.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
resource name = 1 - 50 ASCII characters.
Example:
SEND_COMMAND Panel,"'^BBR-700,1,Sports_Image'"
Sets the resource name of the button to ’Sports_Image’.
^RAF
^RFR
Syntax:
Force a refresh for "'^RFR-<resource name>'"
a given resource.
Variable:
resource name = 1 - 50 ASCII characters.
Example:
SEND_COMMAND Panel,"'^RFR-Sports_Image'"
Forces a refresh on ’Sports_Image’.
^RMF
Syntax:
Modify an
"'^RMF-<resource name>,<data>'"
existing resource.
Variable:
resource name = 1 - 50 ASCII characters
data = Refer to the table in the RAF command for more information.
Example:
SEND_COMMAND Panel,"'^RMF-Sports_Image,%ALab_Test/
Images%Ftest.jpg'"
Changes the resource ’Sports_Image’ file name to ’test.jpg’ and the path to ’Lab_Test/
Images’.
^RSR
Syntax:
Change the
"'^RSR-<resource name>,<refresh rate>'"
refresh rate for a
given resource.
Variable:
resource name = 1 - 50 ASCII characters.
refresh rate = Measured in seconds.
Example:
SEND_COMMAND Panel,"'^RSR-Sports_Image,5'"
Sets the refresh rate to 5 seconds for the given resource (’Sports_Image’).
137
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Dynamic Image Commands (Cont.)
^RAF
Adds any and all resource parameters by sending embedded codes and data.
Add new
Syntax:
resources.
"'^RAF-<resource name>,<data>'"
Variable:
resource name = 1 - 50 ASCII characters.
data = Refers to the embedded codes, see table below.
Embedded Codes:
Parameter
protocol
user
Description
Embedded Code
’%P<0-1>’
Set protocol. HTTP (0) or FTP (1).
Set Username for authentication.
’%U<user>’
password
host
Set Password for authentication.
’%S<password>’
’%H<host>’
Set Host Name (fully qualified
DNS or IP Address).
file
Full path to the location of the file or
program that will return the resource.
The path must be a valid HTTP URL
minus the protocol and host. The
only exception to this is the inclusion
of special escape sequences and in
the case of the FTP protocol, regular
expressions.
’%F<file>’
path
Set Directory path. The path must
be a valid HTTP URL minus the
protocol, host, and filename. The
only exception to this is the
’%A<path>’
inclusion of special escape
sequences and in the case of the
FTP protocol, regular expressions.
refresh
The number of seconds between
refreshes in which the resource is
downloaded again. Refreshing a
resource causes the button
’%R<refresh 1-65535>’
displaying that resource to refresh
also. The default value is 0 (only
download the resource once).
Set the newest file. A value of 1
means that only the most recent file
matching the pattern is downloaded.
newest
’%N<0-1>’
’%V<0-1>’
Set the value of the preserve flag.
Default is 0. Currently preserve has
no function.
preserve
Example:
SEND_COMMAND Panel,"'^RAF-New Image,%P0%HAMX.COM%ALab/
Test_file%Ftest.jpg'"
Adds a new resource. The resource name is ’New Image’, %P (protocol) is an HTTP, %H
(host name) is AMX.COM, %A (file path) is Lab/Test file, and %F (file name) is test.jpg.
138
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Intercom Commands
The following is a list of Intercom Commands:
Intercom Commands
^MODEL?
Panel model name. If the panel supports intercom hardware it will respond with its model
name as shown in the response below. Older hardware or newer hardware that has inter-
com support disabled with not respond to this command.
Sets model name.
Syntax:
SEND_COMMAND <DEV>,"'^MODEL?'"
Variables:
None.
Example:
SEND_COMMAND TP1,"'^MODEL?'"
Panel response string if intercom enabled:
^MODEL-MVP-8400i
^ICS-
^ICS-<IP>,<TX UDP port>,<RX UDP port>,<initial mode>'"
Intercom start.
Intercom start. Starts a call to the specified IP address and ports. The initial mode is either
1 (talk) or 0 (listen) or 2 (both). Please note, however, that no data packets will actually
flow until the intercom modify command is sent to the panel.
Syntax:
SEND_COMMAND <DEV>,"'^ICS-<IP>,<TX UDP port>,<RX UDP
port>,<initial mode>'"
Variables:
IP = IP Address of panel to connect with on an Intercom call.
TX UDP port = UDP port to transmit to.
RX UDP port = UDP port to receive from.
initial mode = 0 (listen) or 1 (talk) or 2 (handsfree). 0 is the default.
Examples:
Example of setting up a handsfree Unicast call between two panels:
SEND_COMMAND TP1,"'^ICS-192.168.0.3,9000,9002,2'"
SEND_COMMAND TP2,"'^ICS-192.168.0.4,9002,9000,2'"
Example of setting up a multicast call where the first panel is paging two other panels:
SEND_COMMAND TP1, "^ICS-239.252.1.1,9000,0,1"
SEND_COMMAND TP2, "^ICS-239.252.1.1,9000,0,0"
SEND_COMMAND TP3, "^ICS-239.252.1.1,9000,0,0"
Example of setting up a baby monitor call where the first panel is listening to the
microphone audio coming from the second panel:
SEND_COMMAND TP1,"'^ICS-192.168.0.3,9000,9002,0'"
SEND_COMMAND TP2,"'^ICS-192.168.0.4,9002,9000,1'"
^ICE'
Intercom end. This terminates an intercom call/connection.
Intercom end.
Syntax:
SEND_COMMAND <DEV>,"'^ICE'"
Variables:
None.
Example:
SEND_COMMAND TP1,"'^ICE'"
SEND_COMMAND TP2,"'^ICE'"
Terminates an intercom call between two panels.
139
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Programming
Intercom Commands (Cont.)
^ICM-TALK
Intercom modify command. For backwards compatibility both versions are supported.
^ICM-LISTEN
In this release, however, the TALK and LISTEN subcommands are ignored. The
microphone and/or speaker are activated based on the initial mode value of the intercom
start command and the audio data packet flow is started upon receipt of this command by
the panel.
Intercom modify
command.
Syntax:
SEND_COMMAND <DEV>,"'^ICM-TALK'"
Variables:
None.
Example:
SEND_COMMAND TP1,"'^ICM-TALK'"
140
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Panel Calibration
Panel Calibration
This section outlines the steps for calibrating the touch panel. It is recommended that you calibrate the
panel both before its initial use and after completing a firmware download.
Modero panels are factory setup with specific demo touch panel pages. The first splash screen that
appears indicates the panel is receiving power, beginning to load firmware, and preparing to display the
default touch panel pages. When the panel is ready, the AMX Splash Screen is replaced by the Initial
Panel Page (FIG. 68).
AMX Splash Screen
(appears during power-up)
Initial Panel Page
(AMX Logo Page)
FIG. 68 AMX splash screen and initial Panel Page
Calibrating the MVP Panels
Setup Access buttons
(bottom button on each side)
3 second press/hold of both buttons:
Opens the Setup page
6 second press/hold of both buttons:
Opens the Calibration page
FIG. 69 Location of Setup Access buttons
2. Using the included stylus, press the crosshairs (on the Calibration page) to set the calibration points
3. After the "Calibration Successful." message appears, press anywhere on the screen to continue and
return to the Setup page.
141
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Panel Calibration
The request to touch the crosshairs
is the first on-screen message
Calibration successful is the second
on-screen message that appears
after the calibration process is
completed
On-screen crosshairs used for
calibration of the touch device
FIG. 70 Touch Panel Calibration Screens
If the calibration was improperly set and you cannot return to the Calibration
page (through the panel’s firmware); you can then access this firmware page via
G4 WebControl where you can navigate to the Protected Setup page and press the
Calibrate button through your VNC window.
This action causes the panel to go to the Calibration page seen above, where you
can physically recalibrate the actual touch panel again using the above procedures.
Testing your Calibration
1. Press and hold down the on-screen Calibration button for 6 seconds to enter the Calibration Test
page (FIG. 71).
On-screen crosshairs is used to
verify a proper calibration of the
panel
FIG. 71 Calibration Test page
2. Press anywhere on this page to confirm the on-screen crosshairs match your touch points.
3. If the crosshairs do not appear directly below your LCD touch points, press the Back button and
recalibrate the panel using the above steps.
Peel the protective plastic film from the LCD.
If the protective plastic film on the LCD is not removed, the panel may not respond
properly to touch points on the LCD nor allow proper screen calibration.
4. Exit this Calibration Test page by pressing the Back button to return to the Protected Setup page.
142
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Panel Calibration
144
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Appendix A: Text Formatting
Appendix A: Text Formatting
Text Formatting Codes for Bargraphs/Joysticks
Text formatting codes for bargraphs provide a mechanism to allow a portion of a bargraphs text to be
dynamically provided information about the current status of the level (multistate and traditional). These
codes are entered into the text field along with any other text.
The following is a code list used for bargraphs:
Bargraph Text Code Inputs
Code
Bargraph
Multi-State Bargraph
$P
Display the current percentage of the
bargraph (derived from the Adjusted
Level Value as it falls between the
Range Values)
Display the current percentage of the
bargraph (derived from the Adjusted
Level Value as it falls between the
Range Values)
$V
$L
$H
$S
$A
Raw Level Value
Range Low Value
Range High Value
N/A
Raw Level Value
Range Low Value
Range High Value
Current State
Adjusted Level Value (Range Low Value Adjusted Level Value (Range Low Value
subtracted from the Raw Level Value)
subtracted from the Raw Level Value)
$R
$$
Low Range subtracted from the High
Range
Low Range subtracted from the High
Range
Dollar sign
Dollar sign
Buy changing the text on a button (via a VT command) you can modify the codes on a button. When one
of the Text Formatting Codes is encountered by the firmware it is replaced with the correct value. These
values are derived from the following operations:
Formatting Code Operations
Code
$P
Operation
(Current Value - Range Low Value / Range High Value - Range Low Value) x 100
Current Level Value
$V
$L
Range Low Value
$H
Range High Value
$S
Current State (if regular bargraph then resolves to nothing)
Current Value - Range Low Value
Range High Value - Range Low Value
$A
$R
Given a current raw level value of 532, a range low value of 500 and a high range value of 600 the
following text formatting codes would yield the following strings as shown in the table below:
Example
Format
Display
$P%
32%
$A out of $R
$A of 0 - $R
$V of $L - $H
32 out of 100
32 of 0 - 100
532 of 500 - 600
145
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Appendix A: Text Formatting
Text Area Input Masking
Text Area Input Masking can be used to limit the allowed/correct characters that are entered into a text
area. For example, in working with a zip code, a user could limit the entry to a max length of only 5
characters but, with input masking, you could limit them to 5 mandatory numerical digits and 4 optional
numerical digits. A possible use for this feature is to enter information into form fields. The purpose of
this feature is to:
• Force you to use correct type of characters (i.e. numbers vs. characters)
• Limit the number of characters in a text area
• Suggest proper format with fixed characters
• Right to Left
• Required or Optional
• Change/Force a Case
• Create multiple logical fields
• Specify range of characters/number for each field
With this feature, it is NOT necessary to:
• Limit you to a choice of selections
• Handle complex input tasks such as names, days of the week or month by name
• Perform complex validation such as Subnet Mask validation
Input mask character types
These character types define what information is allowed to be entered in any specific instance. The
following table lists what characters in an input mask will define what characters are allowed in any
given position.
Character Types
Character Masking Rule
0
9
#
L
?
A
a
&
C
Digit (0 to 9, entry required, plus [+] and minus [-] signs not allowed)
Digit or space (entry not required, plus and minus signs not allowed)
Digit or space (entry not required; plus and minus signs allowed)
Letter (A to Z, entry required)
Letter (A to Z, entry optional)
Letter or digit (entry required)
Letter or digit (entry optional)
Any character or a space (entry required)
Any character or a space (entry optional)
The number of the above characters used determines the length of the input masking
box. Example: 0000 requires an entry, requires digits to be used, and allows only 4
characters to be entered/used.
146
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Appendix A: Text Formatting
Refer to the following Send Commands for more detailed information:
• ^BMFsubcommand %MK - sets the input mask of a text area (see the
Input mask ranges
These ranges allow a user to specify the minimum and maximum numeric value for a field. Only one
range is allowed per field. Using a range implies a numeric entry ONLY.
Input Mask Ranges
Character Meaning
[
]
|
Start range
End range
Range Separator
An example from the above table:
[0|255] This allows a user to enter a value from 0 to 255.
Input mask next field characters
These characters allow you to specify a list of characters that cause the keyboard to move the focus to the
next field when pressed instead of inserting the text into the text area.
Input Mask Next Field Char
Character Meaning
{
}
Start Next Field List
End Next Field List
An example from the above table:
{.} or {:} or {.:} Tells the system that after a user hits any of these keys, proceed to the
next text area input box.
Input mask operations
Input Mask Operators change the behavior of the field in the following way:
Input Mask Operators
Character Meaning
<
>
^
Forces all characters to be converted to lowercase
Forces all characters to be converted to uppercase
Sets the overflow flag for this field
Input mask literals
To define a literal character, enter any character, other than those shown in the above table (including
spaces, and symbols). A back-slash ('\') causes the character that follows it to be displayed as the literal
character. For example, \A is displayed just as the letter A. To define one of the following characters as a
literal character, precede that character with a back-slash. Text entry operation using Input Masks.
147
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Appendix A: Text Formatting
A keyboard entry using normal text entry is straightforward. However, once an input mask is applied, the
behavior of the keyboard needs to change to accommodate the input mask's requirement. When working
with masks, any literal characters in the mask will be "skipped" by any cursor movement including
cursor keys, backspace, and delete.
When operating with a mask, the mask should be displayed with placeholders. The "-" character should
display where you should enter a character. The arrow keys will move between the "-" characters and
allow you to replace them. The text entry code operates as if it is in the overwrite mode. If the cursor is
positioned on a character already entered and you type in a new (and valid) character, the new character
replaces the old character. There is no shifting of characters.
When working with ranges specified by the [] mask, the keyboard allows you to enter a number between
the values listed in the ranges. If a user enters a value that is larger than the max, the maximum number
of right-most characters is used to create a new, acceptable value.
ꢀ
Example 1: If you type "125" into a field accepting 0-100, then the values displayed will be
"1", "12", "25".
ꢀ
Example 2: If the max for the field was 20, then the values displayed will
be "1", "12", "5".
When data overflows from a numerical field, the overflow value is added to the previous field on the
chain, if the overflow character was specified. In the above example, if the overflow flag was set, the first
example will place the "1" into the previous logical field and the second example will place "12" in the
previous logical field. If the overflow field already contains a value, the new value will be inserted to the
right of the current characters and the overflow field will be evaluated. Overflow continues to work until
a field with no overflow value is set or there are no more fields left (i.e. reached first field).
If a character is typed and that character appears in the Next Field list, the keyboard should move the
focus to the next field. For example, when entering time, a ":" is used as a next field character. If you hit
"1:2", the 1 is entered in the current field (hours) and then the focus is moved to the next field and 2 is
entered in that field.
When entering time in a 12-hour format, entry of AM and PM is required. Instead of adding
AM/PM to the input mask specification, the AM/PM should be handled within the NetLinx code. This
allows a programmer to show/hide and provide discrete feedback for AM and PM.
Input mask output examples
The following are some common input masking examples:
Output Examples
Common Name
IP Address Quad
Hour
Input Mask
[0|255]{.}
Input
Any value from 0 to 255
Any value from 1 to 12
Any value from 0 to 59
Any value from 0 to 29
(555) 555-5555
[1|12]{:}
Minute/Second
Frames
[0|59]{:}
[0|29]{:}
Phone Numbers
Zip Code
(999) 000-0000
00000-9999
75082-4567
148
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Appendix A: Text Formatting
URL Resources
A URL can be broken into several parts. For example: the URL http://www.amx.com/company-info-
home.asp. This URL indicates that the protocol in use is http (HyperText Transport Protocol) and that
the information resides on a host machine named www.amx.com. The image on that host machine is
given an assignment (by the program) name of company-info-home.asp (Active Server Page).
The exact meaning of this name on the host machine is both protocol dependent and host dependent. The
information normally resides in a file, but it could be generated dynamically. This component of the
URL is called the file component, even though the information is not necessarily in a file.
A URL can optionally specify a port, which is the port number to which the TCP/IP connection is made
on the remote host machine. If the port is not specified, the default port for the protocol is used instead.
For example, the default port for http is 80. An alternative port could be specified as: http://
www.amx.com:8080/company-info-home.asp.
Any legal HTTP syntax can be used.
Special escape sequences
The system has only a limited knowledge of URL formats in that it transparently passes the URL
information onto the server for translation. A user can then pass any parameters to the server side
programs such as CGI scripts or active server pages. However; the system will parse the URL looking
for special escape codes. When it finds an escape code it replaces that code with a particular piece of
panel, button, or state information.
For example, "http://www.amx.com/img.asp?device=$DV" would become "http://www.amx.com/
img.asp?device=10001". Other used escape sequences include:
Escape Sequences
Sequence
$DV
$SY
$IP
Panel Information
Device Number
System Number
IP Address
$HN
$MC
$ID
Host Name
Mac Address
Neuron ID
$PX
$PY
$BX
$BY
$BN
$ST
X Resolution of current panel mode/file
Y Resolution of current panel mode/file
X Resolution of current button
Y Resolution of current button
Name of button
Current state
$AC
$AP
$CC
$CP
$LC
Address Code
Address Port
Channel Code
Channel Port
Level Code
$LP
Level Port
149
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Appendix A: Text Formatting
150
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Appendix B - Wireless Technology
Appendix B - Wireless Technology
Overview of Wireless Technology
ꢀ
802.11b/2.4 GHz and 802.11a/5 GHz are the two major WLAN standards and both operate
using radio frequency (RF) technology. Together the two standards are together called Wi-Fi
and operate in frequency bands of 2.4 GHz and 5 GHz respectively.
The 802.11b specification was the first to be finalized and reach the marketplace. The actual
throughput you can expect to obtain from an 802.11b network will typically be between 4 and
5 Mbps.
Because of the higher frequency (and thus shorter wavelength) that they use, 802.11a signals
have a much tougher time penetrating solid objects like walls, floors, and ceilings. As a result,
the price for 802.11a's higher speed is not only shorter in range but also a weaker and less
consistent signal.
802.11g provides increased bandwidth at 54 Mbps. As part of the IEEE 802.11g specification,
when throughput cannot be maintained, this card will automatically switch algorithms in
order to maintain the highest spread possible at a given distance. In addition, 802.11g can also
step down to utilize 802.11b algorithms and also maintain a connection at longer distances.
ꢀ
IP Routing is a behavior of the wireless routing is largely dependent on the wired network
interface. Although the panel can be connected to two networks simultaneously it may only
have one gateway. If the wired network was successfully set up and a gateway was obtained;
then the default route for all network traffic will be via the wired network. In the event that the
wired network was not configured, then the default route for all network traffic will be via the
wireless network. The wired network connection always takes priority.
ꢀ
As an example: Imagine a panel connected to two networks A & B. A is the wired
network and B is the wireless network. If the Master controller is on either of these
networks then it will be reached. However if the Master controller is on a different
network, C, then determining which network interface (wired or wireless) that will
be used is dependent on the gateway.
ꢀ
Wireless Access Points are the cornerstone of any wireless network. A Wireless Access Point
acts as a bridge between a wired and wireless network. It aggregates the traffic from all the
wireless clients and forwards it down the network to the switch or router.
One Wireless Access Point may be all you need. However, you could need more Wireless
Access Points depending on either how large your installation is, how it is laid out, and how it
is constructed.
ꢀ Wireless Equivalent Privacy (WEP) Security is a method by which WLANs protect wireless
data streams. A data stream encrypted with WEP can still be intercepted or eavesdropped
upon, but the encryption makes the data unintelligible to the interloper. The strength of WEP
is measured by the length of the key used to encrypt the data. The longer the key, the harder it
is to crack.
802.11b implementations provided 64-bit and 128-bit WEP keys. This is known respectively
as 64-bit and 128-bit WEP encryption. 64-bit is generally not regarded as adequate security
protection. Both key lengths are supported by the Modero product line.
Whichever level of WEP you use, it's crucial to use identical settings (CASE SENSITIVE)--
the key length, and the key itself-- on all devices. Only devices with common WEP settings
will be able to communicate. Similarly, if one device has WEP enabled and another doesn't,
they won't be able to talk to each other.
151
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Appendix B - Wireless Technology
Although the calculations required to encrypt data with WEP can impact the performance of
your wireless network, it's generally seen only when running benchmarks, and not large
enough to be noticeable in the course of normal network usage.
Terminology
ꢀ
802.1x
ꢀ
IEEE 802.1x is an IEEE standard that is built on the Internet standard EAP
(Extensible Authentication Protocol). 802.1x is a standard for passing EAP
messages over either a wired or wireless LAN. Additionally, 802.1x is also
responsible for communicating the method with which WAPs and wireless users can
share and change encryption keys. This continuous key change helps resolve any
major security vulnerabilities native to WEP.
ꢀ
ꢀ
AES
ꢀ
Short for Advanced Encryption Standard, is a cipher currently approved by the NSA
to protect US Government documents classified as Top Secret. The AES cipher is
the first cipher protecting Top Secret information available to the general public.
CERTIFICATES (CA)
ꢀ
A certificate can have many forms, but at the most basic level, a certificate is an
identity combined with a public key, and then signed by a certification authority.
The certificate authority (CA) is a trusted external third party which "signs" or
validates the certificate. When a certificate has been signed, it gains some
cryptographic properties. AMX supports the following security certificates within
three different formats:
- PEM (Privacy Enhanced Mail)
- DER (Distinguished Encoding Rules)
- PKCS12 (Public Key Cryptography Standard #12)
ꢀ
Typical certificate information can include the following items:
- Certificate Issue Date
- Extensions
- Issuer
- Public Key
- Serial Number
- Signature Algorithm
- User
- Version
ꢀ
MIC
ꢀ
Short for Message Integrity Check, prevents forged packets from being sent.
Through WEP it was possible to alter a packet whose content was known even if it
had not been decrypted.
152
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Appendix B - Wireless Technology
ꢀ
TKIP
ꢀ
Short for Temporal Key Integration, is part of the IEEE 802.11i encryption standard
for wireless LANs. TKIP provides per-packet key mixing, message integrity check
and re-keying mechanism, thus ensuring every data packet is sent with its own
unique encryption key. Key mixing increases the complexity of decoding the keys by
giving the hacker much less data that has been encrypted using any one key.
ꢀ
WEP
Short for Wired Equivalent Privacy (WEP), is a scheme used to secure wireless
ꢀ
networks (Wi-Fi). A wireless network broadcasts messages using radio which are
particularly susceptible to hacker attacks. WEP was intended to provide the
confidentiality and security comparable to that of a traditional wired network. As a
result of identified weaknesses in this scheme, WEP was superseded by Wi-Fi
Protected Access (WPA), and then by the full IEEE 802.11i standard (also known as
WPA2).
ꢀ
WPA
ꢀ
Wi-Fi Protected Access (WPA and WPA2) is a class of system used to secure
wireless (Wi-Fi) computer networks. It was created in response to several serious
weaknesses researchers had found in the previous WEP system. WPA implements
the majority of the IEEE 802.11i standard, and was intended as an intermediate
measure to take the place of WEP while 802.11i was prepared (WPA2).
ꢀ
ꢀ
WPA is designed to work with all wireless network interface cards, but not
necessarily with first generation wireless access points.
integrated 802.1x, TKIP and MIC. Within the WPA specifications the RC4 cipher
engine was maintained from WEP. RC4 is widely used in SSL (Secure Socket
Layer) to protect internet traffic.
FIG. 72 WPA Overview
153
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Appendix B - Wireless Technology
ꢀ
WPA2
ꢀ
ꢀ
ꢀ
Also know as IEEE 802.11i, is an amendment to the 802.11 standard specifying
security mechanisms for wireless networks. The 802.11i scheme makes use of the
Advanced Encryption Standard (AES) block cipher; WEP and WPA use the RC4
stream cipher.
The 802.11i architecture contains the following components: 802.1X for
authentication (entailing the use of EAP and an authentication server), RSN for
keeping track of associations, and AES-based CCMP to provide confidentiality,
integrity and origin authentication.
WPA2 implements the full standard, but will not work with some older network
cards. Both provide good security, with two significant issues:
- either WPA or WPA2 must be enabled and chosen in preference to WEP.
WEP is usually presented as the first security choice in most
installation instructions.
- in the "Personal" mode, the most likely choice for homes and small offices,
a passphrase is required that, for full security, must be longer than the
typical 6 to 8 character passwords users are taught to employ.
ꢀ
With the RC4 released to the general public the IEEE implemented the Advanced
Encryption Standard (AES) as the cipher engine for 802.11i, which the Wi-Fi
Alliance has branded as WPA2.
FIG. 73 WPA2 Overview
154
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Appendix B - Wireless Technology
EAP Authentication
EAP (Extensible Authentication Protocol) is an Enterprise authentication protocol that can be used in
both a wired and wireless network environment. EAP requires the use of an 802.1x Authentication
Server, also known as a Radius server. Although there are currently over 40 different EAP methods
defined, the current internal Modero 802.11g wireless card and accompanying firmware only support the
following EAP methods (listed from simplest to most complex):
ꢀ
ꢀ
EAP-LEAP (Cisco Light EAP)
EAP-FAST (Cisco Flexible Authentication via Secure Tunneling, a.k.a. LEAPv2)
The following use certificates:
ꢀ
ꢀ
ꢀ
EAP-PEAP (Protected EAP)
EAP-TTLS (Tunneled Transport Layer Security)
EAP-TLS (Transport Layer Security)
EAP requires the use of an 802.1x authentication server (also known as a Radius server). Sophisticated
Access Points (such as Cisco) can use a built-in Radius server. The most common RADIUS servers used
in wireless networks today are:
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Microsoft Sever 2003
Juniper Odyssey (once called Funk Odyssey)
Meetinghouse AEGIS Server
DeviceScape RADIUS Server
Cisco Secure ACS
EAP characteristics
The following table outlines the differences among the various EAP Methods from most secure (at the
top) to the least secure (at the bottom of the list):
EAP Method Characteristics
Method:
Credential Type:
Authentication:
Pros:
Cons:
EAP-TLS
• Certificates
• Certificate is based on a
two-way authentication
• Highest
Security
• Difficult to
deploy
EAP-TTLS
EAP-PEAP
• Certificates
• Client authentication is
done via password and
certificates
• High Security
• Moderately
difficult to
deploy
• Fixed Passwords
• One-time passwords
(tokens)
• Server authentication is
done via certificates
• Certificates
• Client authentication is
done via password and
certificates
• High Security
• Moderately
difficult to
deploy
• Fixed Passwords
• One-time passwords
(tokens)
• Server authentication is
done via certificates
EAP-LEAP
EAP-FAST
• Certificates
• Authentication is based on • Easy
• Susceptible to
dictionary
attacks
MS-CHAP and
deployment
• Fixed Passwords
MS-CHAPv2
authentication protocols
• One-time passwords
(tokens)
• Certificates
• N/A
• N/A
• N/A
• Fixed Passwords
• One-time passwords
(tokens)
155
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Appendix B - Wireless Technology
EAP communication overview
EAP Authentication goes a step beyond just encrypting data transfers, but also requires that a set of
credentials be validated before the client (panel) is allowed to connect to the rest of the network
(FIG. 74). Below is a description of this process. It is important to note that there is no user intervention
necessary during this process. It proceeds automatically based on the configuration parameters entered
into the panel.
LAN
802.1x
(EAP over Wireless)
Authentication Server
Client - Panel
(supplicant)
Authenticator
(Wireless Access Point)
(RADIUS Server)
FIG. 74 EAP security method in process
1. The client (panel) establishes a wireless connection with the WAP specified by the SSID.
2. The WAP opens up a tunnel between itself and the RADIUS server configured via the access point.
This tunnel means that packets can flow between the panel and the RADIUS server but nowhere
else. The network is protected until authentication of the client (panel) is complete and the ID of
the client is verified.
3. The WAP (Authenticator) sends an "EAP-Request/Identity" message to the panel as soon as the
wireless connection becomes active.
4. The panel then sends a "EAP-Response/Identity" message through the WAP to the RADIUS server
providing its identity and specifying which EAP type it wants to use. If the server does not support
the EAP type, then it sends a failure message back to the WAP which will then disconnect the panel.
As an example, EAP-FAST is only supported by the Cisco server.
5. If the EAP type is supported, the server then sends a message back to the client (panel) indicating
what information it needs. This can be as simple as a username (Identity) and password or as
complex as multiple CA certificates.
6. The panel then responds with the requested information. If everything matches, and the panel
provides the proper credentials, the RADIUS server then sends a success message to the access
point instructing it to allow the panel to communicate with other devices on the network. At this
point, the WAP completes the process for allowing LAN Access to the panel (possibly a restricted
access based on attributes that came back from the RADIUS server).
ꢀ
As an example, the WAP might switch the panel to a particular VLAN or install a set of
firewall rules.
156
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Appendix B - Wireless Technology
AMX Certificate Upload Utility
The Certificate Upload utility gives you the ability to compile a list of target touch panels, select a pre-
obtained certificate (uniquely identifying the panel), and then upload that file to the selected panel.
This application must be run from a local machine and should not be used from a
remote network location.
This application ensures that a unique certificate is securely uploaded to a specific touch panel.
Currently, the target panels must be capable of supporting the WPA-PSK and EAP-XXX wireless
security formats.
The Certificate Upload utility supports the following capabilities:
ꢀ
ꢀ
Ability to browse both a local and network drive to find a desired certificate file.
Ability to create a list of target AMX G4 touch panels based on IP Addresses
- Compatible panels include: MVP-8400, MVP-7500, NXD-CV10, NXT-CV10,
NXD-CV7, and NXT-CV7.
ꢀ
ꢀ
ꢀ
ꢀ
Ability to display the IP Address of the local computer hosting the application.
Ability to load a previously created list of target touch panels.
Ability to save the current list of target Modero panel as a file.
Ability to track the progress of the certificate upload by noting the current data size being
transmitted and any associated error messages (if any).
The Certificate Upload Utility recognizes the following certificate file types:
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
CER (Certificate File)
DER (Distinguished Encoding Rules)
PEM (Privacy Enhanced Mail)
PFX (Normal Windows generated certificate)
PVK (Private Key file)
Configuring your G4 Touch Panel for USB Communication
For a personal computer to establish a connection to a Modero panel via USB, the target computer must
have the appropriate AMX USB driver installed. This installation is bundled into the latest TPDesign4
and NetLinx Studio2 software setup process or can be downloaded independently from the main
Application Files page on www.amx.com.
Close the Certificate Upload Utility before configuring the touch panel's USB driver.
Only after the panel has been successfully setup to communicate via USB can you
then re-launch the utility.
Step 1: Setup the Panel and PC for USB Communication
1. If you do not currently have the latest version of TPDesign4, navigate to www.amx.com > Tech
Center > Downloadable Files > Application Files > NetLinx Design Tools section of the website
and locate the AMX USB Driver executable (AMX USBLAN Setup exe).
2. Download this executable file to a known location on your computer.
3. Launch the Setup.exe and follow the on-screen prompts to complete the installation.
157
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Appendix B - Wireless Technology
Step 2: Confirm the Installation of the USB Driver on the PC
The first time each AMX touch panel is connected to the PC it is detected as a new hardware device and
the USBLAN driver becomes associated with it (panel specific). Each time thereafter the panel is
"recognized" as a unique USBLAN device and the association to the driver is done in the background.
When the panel is detected for the first time some user intervention is required during the association
between panel and driver.
1. After the installation of the USB driver has been completed, confirm the proper installation of the
large Type-A USB connector to the PC's USB port, and restart your machine.
If the panel is already powered, continue with steps 3. The panel MUST be powered
and configured for USB communication before connecting the mini-USB connector to
the panel’s Program Port.
2. Connect the terminal end of the power cable to the 12 VDC power connector on the side/rear of the
pane, and supply power. If using an MVP that is installed onto a docking station, feed power to the
docked panel by connecting the appropriate power supply to the docking station.
3. After the panel powers-up, access the firmware setup pages by either:
- MVP - Pressing and holding the two lower buttons on both sides of the display for 3 seconds.
- CV7/CV10 - Pressing the grey Front Setup Access button for 3 seconds.
4. Select Protected Setup > System Settings (located on the lower-left) to open the System Settings
page.
5. Toggle the blue Type field (from the Master Connection section) until the choice cycles to USB.
ꢀ
The connection remains RED after changing the communication from Ethernet to USB until
the panel is rebooted.
ꢀ
Once the panel restarts, the connection turns a dark green until connected to an active USB
cable.
6. Press the Back button on the touch panel to return to the Protected Setup page.
7. Press the on-screen Reboot button to both save any changes and restart the panel. Remember that
the panel’s connection type must be set to USB prior to rebooting the panel and prior to inserting the
USB connector.
8. ONLY AFTER the unit displays the first panel page, THEN insert the mini-USB connector
into the Program Port on the panel.
ꢀ
It may take a minute for the panel to detect the new connection and send a signal to the PC
(indicated by a green System Connection icon). If this is your first time installing the USB
driver, a USB driver installation popup window appears on the PC.
9. Complete the USB driver installation process by clicking Yes and then installing the new AMX
USB LAN LINK when told that a new USB device was found. This action accepts the installation
of the new AMX USB driver.
10. Reboot the panel. Once restarted, the panel is now configured to communicate directly with the PC.
The mini-USB connector MUST be then plugged into an already active panel before
the PC can recognize the connection and assign an appropriate USB driver. This
driver is part of both the NetLinx Studio and TPDesign4 software application
installations.
158
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Appendix B - Wireless Technology
11. Launch the Certificate Upload Utility and confirm the utility has detected the new USB connection
to the panel:
ꢀ
ꢀ
Click on the Local Address field's drop-down arrow.
Confirm the new USB entry shows up in the list as: 10.XX.XX.1.
How to Upload a Certificate File
1. Install the latest AMX USB LAN LINK driver onto your computer by installing the latest versions
of either TPDesign4 or NetLinx Studio2. This USB driver prepares your computer to properly
communicate with a directly connected G4 touch panel (MVP/CV7/CV10).
ꢀ
Refer to Step 1 from within the previous Step 1: Setup the Panel and PC for USB
2. Access the target panel's Protected Setup firmware page and configure the USB communication
parameters.
3. With the panel successfully communicating with target computer, launch the Certificate Upload
Utility.
ꢀ
Familiarize yourself with the User Interface options (Certificate Utility User Interface).
4. Locate your certificate file by using the Browse button and navigating to the desired file type.
5. Use the drop-down arrow in the Local Address field to select communication through either the
computer's Ethernet port (Internet communication) or via the USB port (direct connection). If using
an Ethernet connection skip to step 8.
6. For a USB connection, select the 10.XX.XX.1 IP Address which corresponds to the virtual IP
Address assigned to the USB connection port on the computer.
7. For a USB connection, navigate to the Add IP Address field (bottom-right of the interface) and
enter a value of 1 greater than the virtual USB IP Address.
ꢀ
ꢀ
For example: If the virtual USB IP Address is 10.0.0.1 then you would add an address for the
directly connected panel of 10.0.0.2 (this is one greater than the USB address value detected
by the utility).
You can send a certificate to ONLY ONE directly connected panel (via USB). If using the
Ethernet port's IP Address, you can send a server certificate to multiple target panels.
8. For an Ethernet IP Address connection, select the IP Address which corresponds to the local
computer's Ethernet address.
9. Navigate to the Add IP Address field (bottom-right of the interface) and enter the IP Addresses of
the various target touch panels.
10. Click the Add button to complete the entry and add the new IP Address to the listing of available
device IP Addresses. Repeat this process for all subsequent device IP Addresses.
11. Once your list is complete, click on the File drop-down menu and select the Save option to launch a
Save dialog where you can assign a name to the current list of addresses and then save the
information (as a TXT (text) file) to a known location.
This application must be run from a local machine and should not be used from a
remote network location.
159
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Appendix B - Wireless Technology
12. Select the target devices which be uploaded with the selected certificate. These can either be:
ꢀ
ꢀ
individually selected by toggling the box next to the Send entry (with the Type column).
selected as a group by clicking on the Check All radio box located at the top of the device IP
Address listing.
13. When you are ready to send the certificate file to the selected panels, click the Send button to
initiate the upload.
ꢀ
Once the Status field for each entry reads Done, your upload was successfully completed.
160
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Appendix B - Wireless Technology
161
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Appendix B - Wireless Technology
162
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Appendix C: Troubleshooting
Appendix C: Troubleshooting
This section describes the solutions to possible hardware/firmware issues that could arise during the
common operation of a Modero touch panel.
Panel Doesn’t Respond To Touches
ꢀ
Verify that the protective laminate coating on the LCD is removed before beginning any
calibration process.
ꢀ
The protective cover acts to press on the entire LCD and makes calibration difficult because
the user can’t calibrate on specific crosshairs when the sheet is pressing on the whole LCD.
Batteries Will Not Hold Or Take A Charge
Symptom: Batteries will not hold or take a charge and there is no indication of charging, on the
bargraphs or in the Batteries Setup page.
To keep the batteries from being damaged (from operating at too low a level), the firmware places them
into a protected state.
The panel must have the latest firmware (if it doesn’t, the firmware can be found at amx.com, in the
Dealers/Tech Center > Firmware Files.> Modero).
1. Load the firmware into the panel, using NetLinx Studio.
2. After loading the firmware, power cycle the MVP (this is a complete power cycle, not a Reboot).
The panel will now show the current firmware version within the Setup > Panel Information page.
3. Connect the power supply to the panel. You will see 2 warning messages on the display.
ꢀ
ꢀ
The first one warns that the batteries are low and must be charged.
The second warning tells you that the second battery is in aprotected mode, and needs to be
inserted into the first battery slot.
4. Swap the batteries, the top slot is considered the first slot, and now the batteries will be reset.
5. Wait a few minutes and then check the Batteries page on the MVP to see any charging activity on
the bar graphs.
The "Sensor" device (in the Online Tree tab below the MVP panel)should show v1.24 or
higher after the upgrade, as shown in FIG. 75:
FIG. 75 "Sensor" device in the Online Tree tab
163
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Appendix C: Troubleshooting
Modero Panel Isn’t Appearing In The Online Tree Tab
1. Verify that the System number is the same on both the NetLinx Project Navigator window and the
System Settings page on the Modero panel.
2. Verify you have entered the proper NetLinx Master IP and connection methods into the Master
Connection section of the System Settings page.
MVP Can’t Obtain a DHCP Address
In requesting a DHCP Address, the DHCP Server can take up to a few minutes to provide the address.
1. Verify that the WAP is configured to match the MVP panel Network Name (SSID) field,
Encryption, Default Key, and Current Key string.
Remember that the Passphrase generator on the panel does not produce the same
Current Key if using the same passphrase on the WAP.
2. In NetLinx Studio, select Diagnostics > Network Address and verify the System number.
3. If the IP Address field is still empty, give the Modero a few minutes to negotiate a DHCP Address
and try again.
My WEP Doesn’t Seem To Be Working
WEP will not work unless the same default key is set on both the panel and the Wireless Access Point
(WAP).
For example: if you had your access point set to default WEP key 4 (which was 01:02:03:04:05) you
must also set the Modero’s Default WEP key 4 to 01:02:03:04:05.
NetLinx Studio Only Detects One Of My Connected Masters
Each Master is given a Device Address of 00000.
Only one Master can be assigned to a particular System number. If you want to work with multiple
Masters, open different instances of NetLinx Studio and assign each Master its own System value.
Example: A site has an NXC-ME260/64 and an NI-4000. In order to work with both units. The ME260
can be assigned System #1 and the NI-4000 can then be assigned System #2 using two open sessions of
NetLinx Studio v 2.x.
Can’t Connect To a NetLinx Master
Symptom: I can’t seem to connect to a NetLinx Master using NetLinx Studio 2.
Select Settings > Master Comm Settings > Communication Settings > Settings (for TCP/IP), and
uncheck the "Automatically Ping the Master Controller to ensure availability".
The pinging is to determine if the Master is available and to reply with a connection failure instantly if it
is not. Without using the ping feature, you will still attempt to make a connection, but a failure will take
longer to be recognized.
If you are trying to connect to a Master controller that is behind a firewall, you may
have to uncheck this option. Most firewalls will not allow ping requests to pass
through for security reasons.
When connecting to a NetLinx Master controller via TCP/IP, the program will first try to ping the
controller before attempting a connection. Pinging a device is relatively fast and will determine if the
device is off-line, or if the TCP/IP address that was entered was incorrect.
164
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Appendix C: Troubleshooting
If you decide NOT to ping for availability and the controller is off-line, or you have an incorrect TCP/IP
address, the program will try for 30-45 seconds to establish a connection.
Only One Modero Panel In My System Shows Up
Symptom: I have more than one Modero panel connected to my System Master and only one shows up.
Multiple NetLinx Compatible devices (such as MVP panels) can be associated for use with a single
Master. Each panel comes with a defaulted Device Number value of 10001. When using multiple panels,
it is necessary to assign different Device Number values to each panel.
1. Press and hold the two lower buttons on both sides of the display for 3 seconds to open the Setup
page.
2. Press the Protected Setup button (located on the lower-left of the panel page), enter 1988 into the
on-screen Keypad’s passwordfield, and press Done when finished.
3. Enter a Device Number value for the panel into the Device Number Keypad.
The default is 10001 and the range is from 1 - 32000.
Panel Behaves Strangely After Downloading A Panel File Or Firmware
Symptom: After downloading a panel file or firmware to a G4 device, the panel behaves strangely.
If the panel already contains a large enough file, subsequent downloads will take up more space than is
available and could often corrupt the Compact Flash. The demo file that typically ships with G4 panels is
one such file.
Symptoms include:
ꢀ
ꢀ
Having to repeat the download.
Inability to make further downloads to the panel. May get "directory" errors, "graphics
hierarchy" errors, etc., indicating problems with the Compact Flash.
ꢀ
Panel will not boot, or gets stuck on "AMX" splash screen.
Other problems also started after downloading to a new panel or a panel with a TPD4 file that takes up a
considerable amount of the available Compact Flash.
1. DO NOT download TPD4 files (of large size) over the demo pages, or any other large TPD4 file.
2. First download a small blank one page file to the G4 panel using the Normal Transfer option to
send/download the page.
3. Reboot the device.
4. Do your regular file or firmware download.
165
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Appendix C: Troubleshooting
166
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
Appendix C: Troubleshooting
167
MVP-7500/8400 Modero Viewpoint Wireless Touch Panels
It’s Your World - Take Control™
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 USA • 800.222.0193 • 469.624.8000 • 469-624-7153 fax • 800.932.6993 technical support • www.amx.com
|