AMD PPC L106T User Manual

PPC-L106T  
AMD LX800 processor-based  
Panel PC with 10.4" TFT LCD flat  
panel display  
User Manual  
FCC Class B  
This equipment has been tested and found to comply with the limits for a  
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits  
are designed to provide reasonable protection against harmful interfer-  
ence when the equipment is operated in a residential environment. This  
equipment generates, uses and can radiate radio frequency energy. If not  
installed and used in accordance with this user manual, it may cause  
harmful interference to radio communications. Note that even when this  
equipment is installed and used in accordance with this user manual, there  
is still no guarantee that interference will not occur. If this equipment is  
believed to be causing harmful interference to radio or television recep-  
tion, this can be determined by turning the equipment on and off. If inter-  
ference is occurring, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
• Reorient or relocate the receiving antenna  
• Increase the separation between the equipment and the receiver  
• Connect the equipment to a power outlet on a circuit different from that  
to which the receiver is connected  
• Consult the dealer or an experienced radio/TV technician for help  
Warning! Any changes or modifications made to the  
equipment which are not expressly approved by  
the relevant standards authority could void your  
authority to operate the equipment.  
iii  
Packing List  
Before you begin installing your card, please make sure that the following  
materials have been shipped:  
• PPC-L106T series panel PC  
• Accessories for PPC-L106T  
- Keyboard extension cable (5-pin DIN female to 6-pin PS/2 male)  
- HDD flat cable (44-pin) (8 cm)  
- Power cord (1.8 m) - USA type  
- HDD bracket  
- Driver/Utility CD-ROM disk  
- Screws  
- Warranty card  
If any of these items are missing or damaged, contact your distributor or  
sales representative immediately.  
Additional Information and Assistance  
Step 1. Visit the our web site where you can find the latest  
information about the product.  
Step 2. Contact your distributor, sales representative, or customer  
service center for technical support if you need additional  
assistance. Please have the following information ready before  
you call:  
• Product name and serial number  
• Description of your peripheral attachments  
• Description of your software (operating system, version, application  
software, etc.)  
• A complete description of the problem  
• The exact wording of any error messages  
PPC-L106T User Manual  
iv  
Safety Instructions  
1. Please read these safety instructions carefully.  
2. Please keep this User Manual for later reference.  
3. Please disconnect this equipment from any AC outlet before cleaning. Do not  
use liquid or spray detergents for cleaning. Use a damp cloth.  
4. For pluggable equipment, the socket-outlet must be installed near the equip-  
ment and must be easily accessible.  
5. Please keep this equipment away from humidity.  
6. Put this equipment on a reliable surface during installation. Dropping it or let-  
ting it fall could cause damage.  
7. The openings on the enclosure are for air convection. Protect the equipment  
from overheating. DO NOT COVER THE OPENINGS.  
8. Make sure the voltage of the power source is correct before connecting the  
equipment to the power outlet.  
9. Position the power cord so that people cannot step on it. Do not place anything  
over the power cord.  
10. All cautions and warnings on the equipment should be noted.  
11. If the equipment is not used for a long time, disconnect it from the power  
source to avoid damage by transient overvoltage.  
12. Never pour any liquid into an opening. This could cause fire or electrical  
shock.  
13. Never open the equipment. For safety reasons, the equipment should be  
opened only by qualified service personnel.  
14. If one of the following situations arises, get the equipment checked by service  
personnel:  
a. The power cord or plug is damaged.  
b. Liquid has penetrated into the equipment.  
c. The equipment has been exposed to moisture.  
d. The equipment does not work well, or you cannot get it to work according  
to the user manual.  
e. The equipment has been dropped and damaged.  
f. The equipment has obvious signs of breakage.  
15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVI-  
RONMENT WHERE THE STORAGE TEMPERATURE MAY GO  
BELOW -20° C (-4° F) OR ABOVE 60° C (140° F). IT MAY DAMAGE  
THE EQUIPMENT.  
The sound pressure level at the operator's position according to IEC 704-  
1:1982 is equal to or less than 70 dB(A).  
DISCLAIMER: This set of instructions is supplied according to IEC 704-  
1. We disclaim all responsibility for the accuracy of any state-  
ments contained herein.  
v
Wichtige Sicherheishinweise  
1. Bitte lesen sie Sich diese Hinweise sorgfältig durch.  
2. Heben Sie diese Anleitung für den späteren Gebrauch auf.  
3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie  
Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch  
zur Reinigung.  
4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht  
zugänglich sein.  
5. Das Gerät ist vor Feuchtigkeit zu schützen.  
6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen  
oder Fallen könnte Verletzungen hervorrufen.  
7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor überhit-  
zung schützt. Sorgen Sie dafür, daB diese Öffnungen nicht abgedeckt werden.  
8. Beachten Sie beim. AnschluB an das Stromnetz die AnschluBwerte.  
9. Verlegen Sie die NetzanschluBleitung so, daB niemand darüber fallen kann.  
Es sollte auch nichts auf der Leitung abgestellt werden.  
10. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu  
beachten.  
11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom  
Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädi-  
gung vermieden.  
12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten  
in das Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag aus-  
lösen.  
13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen  
Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.  
14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen  
und von einer qualifizierten Servicestelle zu überprüfen:  
a - Netzkabel oder Netzstecker sind beschädigt.  
b - Flüssigkeit ist in das Gerät eingedrungen.  
c - Das Gerät war Feuchtigkeit ausgesetzt.  
d - Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert  
oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.  
e - Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.  
f - Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.  
15. VOSICHT: Explisionsgefahr bei unsachgemaben Austausch der Batte-  
rie.Ersatz nur durch densellben order einem vom Hersteller empfohlene-  
mahnlichen Typ. Entsorgung gebrauchter Batterien navh Angaben des  
Herstellers.  
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000  
beträgt 70dB(A) oder weiger.  
DISCLAIMER: This set of instructions is supplied according to IEC704-  
1. We disclaim all responsibility for the accuracy of any state-  
ments contained herein.  
PPC-L106T User Manual  
vi  
Contents  
vii  
1
General Information  
This chapter gives background  
information on the PPC-L106T.  
Sections include:  
Introduction  
Specifications  
LCD Specifications  
Dimensions  
I/O Arrangement  
Cutout (Suggestion)  
Mounting  
Chapter 1 General Information  
1.1 Introduction  
The PPC-L106T is a 10.4" LCD Panel PC with an AMD LX800 CPU that  
is designed to serve as a human machine interface (HMI). It is a PC-based  
system with 10.4" color TFT LCD display, on-board PCI Ethernet, multi-  
COM port interfaces, and a 16-bit audio controller. This simple, com-  
plete, compact and highly integrated multimedia system lets you easily  
build a panel PC into your applications. By incorporating the PPC-L106T  
into your project, your product development time will be shortened.  
The PPC-L106T is a compact, network-compatible PC with extensive  
features to control a dedicated system in a wide variety of applications.  
Common industrial applications include factory automation systems, pre-  
cision machinery, and production process control. It is also suitable for  
many nonindustrial applications, including terminal information systems,  
entertainment management systems, and car park automation systems.  
Our panel PC is a reliable, cost-effective solution to your application's  
processing requirements.  
1.2 Specifications  
General  
Dimensions (W x H x D): 342 x 265 x 92.4 mm  
(13.5"x10.4"x3.6")  
Weight: 3.2 kg (7.1 lbs)  
Power supply:  
AC model: 65 watts  
Input voltage: 100 ~ 240Vac, 2A, 50 ~ 60 Hz  
Output voltage: +5 V @ 3.5 A, +12 V @ 4 A  
Safety: UL/CB/CCC/BSMI approved  
Disk drive housing: Space for one internal 2.5" HDD  
Front panel protection: IP 65/NEMA 4 compliant  
Standard PC functions  
CPU: AMD LX800 (500 MHz) processor on board  
BIOS: AWARD 4M bit Flash BIOS, supports Plug & Play, APM v1.2  
Chipset: AMD CS 5536  
2 PPC-L106T User Manual  
     
2nd level cache: 128 KB on CPU  
RAM: One 200-pin SODIMM sockets accept 256 ~ 1024 MB  
DDR  
PCI Bus Master IDE interface: Supports two connectors (one  
internal, one external). Each connector supports two IDE  
devices on two channels (PIO modes 3/4). BIOS supports IDE  
(PIO mode 0~4, DMA mode 0~2, and Ultra DMA33 simulta-  
neously). Default: CF Slot set as Master  
Parallel port: One parallel port, supports SPP/EPP/ECP parallel  
mode.  
Serial ports: Four serial ports with three RS-232 ports (COM1, 3,  
and 4), one RS-232/422/485 port (COM2). All ports with  
16C550 compatible UARTs. Default COM4 reserved for Touch  
USB: Supports four USB 2.0 (2 x internal, 2 x external)  
PCI/ISA bus expansion slot: Accepts either one ISA or one PCI  
bus card.  
Watchdog timer: 256-level interval from 1 to 255 seconds.  
Jumperless selection and software enabled/disabled.  
Battery: 3 V @ 195 mA lithium battery for CMOS backup  
Solid State Disk (SSD)  
One 50-pin socket: for one CompactFlash™ Type II storage card,  
shared with one IDE channel.  
PCI SVGA/flat panel interface  
Chipset: AMD CS 5536  
Display memory: 1.5~4 MB share memory  
Display type: Simultaneously supports CRT and flat panel displays  
Display resolution: Supports non-interlaced CRT and LCD dis-  
plays up to 800 x 600 @ 256 K colors with 1.5~4 MB shared  
memory  
Audio function:  
Audio Chipset: ALC203, fully compliant AC 97 analog I/O com-  
ponent, 16-bit stereo full-duplex codec, audio interface for  
microphone-in, line-in and speaker out  
PCI bus Ethernet interface  
Chapter 1 General Information 3  
Ethernet Chipset: Realtek RTL8100C PCI local bus Ethernet con-  
troller fully compliant with IEEE 802.3u 10/100 Base-T speci-  
fications.  
Touchscreen (optional)*  
Type  
Analog Resistive  
Infrared  
Continuous  
4096 x 4096  
Resolution  
Light Transmission  
Controller  
80%  
91%  
RS-232 interface  
(uses COM4)  
Optional USB  
interface  
<5 V @ 200 mA  
5 V @ 100 mA  
Power Consumption  
Software Driver  
Supports Windows CE Supports Windows CE  
/XP  
/XP  
35 million  
100,000 hrs  
Durability (touches  
in a lifetime)  
*Note: The PPC-L106T with the optionally installed touchscreen will  
share COM4.  
Environment  
Temperature: 45° C (32 ~ 125° F)  
Relative humidity: 10 ~ 95% @ 40° C, non-condensing  
Shock: 10G peak acceleration (11 msec duration)  
Power MTBF: 50,000 hrs  
Certification: CE, FCC Class B, BSMI, CCC  
4 PPC-L106T User Manual  
1.3 LCD Specifications  
Default  
Optional  
10.4" SVGA TFT  
10.4" SVGA TFT  
Display type (LCD)  
Max. resolution  
Colors  
800 x 600  
262 K colors  
120 / 100  
0.264 X 0.264  
230  
800 x 600  
262 K colors  
140 / 100  
0.264 X 0.264  
400  
View angle  
Dot size (mm)  
Luminance (cd/mð)  
Temperature (°C)  
VR controls  
0 ~ 50  
0 ~ 50  
Yes*  
Yes*  
Yes  
Yes  
Simultaneous mode  
Lamp Life (hrs)  
20,000 hours  
50,000 hours  
* The VR control is defined by hot key in DOS or BIOS mode as follows:  
Ctrl-Alt-F3, Ctrl-Alt-F4  
Chapter 1 General Information 5  
 
1.4 Dimensions  
Figure 1.1: PPC-L106T panel PC dimensions  
6 PPC-L106T User Manual  
 
1.5 I/O Arrangement  
Figure 1.2: PPC-L106T back panel I/O arrangement and cable connec-  
tions  
A. Power switch  
B. Parallel port  
F. COM ports  
G. COM ports  
H. VGA port  
C. PS/2 mouse connector  
D. Mic-in/Line-out  
E. AC inlet  
I. USB ports V2.0  
J. Ethernet  
* Three RS-232 (COM1, 3, 4) and one RS-232/422/485 (COM2)  
Chapter 1 General Information 7  
 
1.6 Cutout (Suggestion)  
The PPC-L106T will stand on a shelf or a table, or you can mount it into  
a panel. Cutout panel dimensions are as follows  
Figure 1.3: PPC-L106T panel mounting cutout  
dimensions  
8 PPC-L106T User Manual  
 
1.7 Mounting  
1.7.1 Panel mounting  
If you decide to use a cutout within a panel to mount your PPC-L106T,  
we have included two panel-mount brackets. The brackets have two  
screws that fit in the keyhole slots on the panel PC.  
Slide the PPC-L106T backwards into the panel opening. Attach the two  
mounting brackets by sliding the two screw heads into the keyhole slots  
on the rear cover. Secure the PPC-L106T against the back of the panel  
opening.  
Figure 1.4: PPC-L106T rear panel mounting brackets  
Chapter 1 General Information 9  
   
1.7.2 Desktop stand (optional)  
An optional stand is available for mounting the PPC as a desktop PC. The  
PPC-L106T slides into the stand and is held in place by the screws pro-  
vided. The compactness of the desktop-mounted PPC-L106T saves desk  
space.  
Figure 1.5: PPC-L106T desktop stand  
10 PPC-L106T User Manual  
 
1.7.3 Wall-mounting (optional)  
An optional wall-mounting attachment is also available for mounting the  
PPC at approximately 45° to a flat surface. Installation instructions fol-  
low:  
1.  
2.  
3.  
The wall-mounting attachment is comprised of three parts: one  
back bracket, one support bracket, and one mounting bracket.  
First attach the back bracket to the rear cover of the PPC-L106T,  
securing it in place with four of the philips-head screws provided.  
Using a flat-head screwdriver, attach the support bracket to the  
back bracket using four of the flat-head screws provided, two on  
either side of the support bracket. The sides of the support bracket  
should overlap the sides of the back bracket, and the screws should  
secure one bracket to the other through the existing holes drilled  
into each bracket.  
4.  
Mount the mounting bracket on the wall or other flat surface. The  
support bracket slides vertically from the top into the mounting  
bracket. It can then can be secured to the mounting bracket by  
screwing one of the philips-head screws provided through the cor-  
responding holes at the tops of the mounting bracket and the sup-  
port bracket.  
Figure 1.6: PPC-L106T wall mounting configuration  
Chapter 1 General Information 11  
 
12 PPC-L106T User Manual  
2
System Setup  
Sections include:  
General  
Removing Rear Panel  
Installing Options  
Installing I/O Equipment  
Installing Software to the HDD  
Exploded Diagram  
PCM-9679 and I/O Adapter  
Replacement  
Power Supply and Cooling Fan  
Replacement  
Chapter 2 System Setup  
2.1 General  
The PPC-L106T consists of a PC-based industrial computer that is  
housed in a protective cover. Your HDD, DDR RAM and power supply  
and are all readily accessible by removing the rear panel. Any mainte-  
nance or hardware upgrades can be carried out easily after removing the  
rear panel.  
Warning! Do not remove the rear cover until you have  
verified that no power is flowing within the PPC-  
L106T. Power must be switched off, and the  
power cord must be disconnected. Every time  
you service the PPC-L106T, you should be  
aware of this.  
2.2 Preparing For First Time Use  
Before you set up the PPC-L106T system, you should have at least the  
following items ready:  
Power cord (in the accessory box)  
PS/2 keyboard  
PS/2 mouse (for system software installation, i.e. MS Windows,  
NT, etc.)  
14 PPC-L106T User Manual  
     
2.3 Installing Options  
2.3.1 Removing Rear Panel  
Unscrew the eleven screws that secure the rear cover, then remove the  
cover.  
Figure 2.1: Removing the rear panel  
Chapter 2 System Setup 15  
   
2.3.2 Installing a primary 2.5" HDD (internal)  
You can attach one enhanced Integrated Device Electronics (IDE) hard  
disk drive to the PPC-L106T's internal controller which uses a PCI local-  
bus interface. The advanced IDE controller supports faster data transfer  
rates and allows the IDE hard drive to exceed 528 MB. The following are  
instructions for installation:  
1.  
2.  
Detach the rear panel and remove.  
Place the HDD in the appropriate location inside the PPC-L106T,  
and tighten the screws.  
3.  
Connect the cable included in this package (1x44-pin to 1x44-pin)  
from the HDD to the PC board (CN9). Make sure that the red/blue  
wire corresponds to pin 1 on the connector, which is labeled on the  
board. Plug the other end of the cable into the enhanced IDE hard  
drive, with pin 1 on the cable corresponding to pin 1 on the hard  
drive.  
Warnings! (1) Plug the other end of the cable into the  
HDD, with pin 1 on the cable corresponding to  
pin 1 on the hard drive. Improper connection  
will damage the HDD.  
(2) Be careful not to damage the CPU board  
with your tools!  
Figure 2.2: Installing a primary 2.5" HDD (internal)  
16 PPC-L106T User Manual  
 
2.4 Installing I/O Equipment  
2.4.1 PS/2 keyboard and PS/2 mouse  
The PPC-L106T provides a PS/2 keyboard connector that supports a PS/2  
style keyboard and a 5-pin DIN keyboard extension cable. In most cases,  
especially in embedded applications, a keyboard is not used. The standard  
PC/AT BIOS will report an error or failure during power-on self-test  
(POST) after a reset if the keyboard is not present. The BIOS standard  
setup menu allows you to select* "All, But Keyboard" under the "Halt  
On" selection. This allows no-keyboard operation in embedded system  
applications without the system halting under POST. Note that the mouse  
port on the PPC-L106T is a PS/2 mouse port.  
Note:  
“All but keyboard” is the default setting.  
2.4.2 Mic-in, line-out  
The PPC is equipped with a high quality audio interface, which provides  
16-bit CD quality recording and playback as well as OPL3 compatible  
FM music. It is supported by all major operating systems and is com-  
pletely compatible with Sound Blaster Pro.  
The audio interface includes two jacks: microphone-in and line-out (See  
Fig. 1-2).  
2.4.3 External VGA  
The PPC-L106T can be connected to an external CRT monitor. To con-  
nect an external CRT monitor, connect the monitor's VGA cable to the  
PPC-102's VGA port and connect the monitor's power cable to an AC  
outlet. The PPC-L106T's external CRT display (VGA) connector is a  
standard 15-pin D-SUB connector commonly used for VGA.  
2.4.4 Four serial COM ports  
Many available peripherals, such as a serial mouse or an optional touch-  
screen, require connection to a serial port. When an optional touchscreen  
is ordered with a PPC-L106T, it shares COM4, and COM4 is not avail-  
able as a serial port.  
Chapter 2 System Setup 17  
         
2.4.5 Ethernet  
The PPC-L106T is equipped with a high performance 32-bit Ethernet  
chipset which is fully compliant with the IEEE 802.3 100 Mbps CSMA/  
CD standards. It is supported by major network operating systems. It is  
also both 100Base-T and 10Base-T compatible. The medium type can be  
configured via the RSET8139.EXE program included on the utility disk.  
The Ethernet port provides a standard RJ-45 jack. The network boot fea-  
ture can be utilized by incorporating the boot ROM image files for the  
appropriate network operating system. The boot ROM BIOS files are  
combined with system BIOS, which can be enabled/disabled in the BIOS  
setup.  
2.4.6 USB ports  
The external USB device may be connected to the system though the 4-  
pin USB ports located on the rear side of the system unit.  
The USB ports support hot plug-in connection. You should install the  
device driver before you use the device.  
2.5 Installing Software to the HDD  
Installing software requires an installed HDD. Software can be loaded in  
the PPC-L106T using any of four methods:  
2.5.1 Method 1: Use the Ethernet  
You can use the Ethernet port to download software to the HDD.  
2.5.2 Method 2: Use a USB Disk or USB CD-ROM  
You can use a USB disk or USB CD-ROM to download the software to  
your HDD.  
2.5.3 Method 3: Use the COM or parallel port  
Connect another PC to the PPC-L106T with an appropriate cable and  
transmit the software to the PPC-L106T.  
18 PPC-L106T User Manual  
           
2.6 Exploded Diagram  
Figure 2-3 shows all the components and parts that make up the PPC-  
L106T. Use it as a guide when assembling and disasesembling your sys-  
tem.  
Figure 2.3: PPC-L106T exploded diagram  
Chapter 2 System Setup 19  
 
2.7 PCM-9679 and I/O Adapter Replacement  
To replace or service the PCM-9679 (all-in-one CPU board) and I/O  
adapter, complete the following steps:  
1.  
2.  
3.  
Turn off the power to the PPC-L106T  
Remove the rear protective cover (see Figure 2-1)  
Install the PCM-9679 in the panel and screw in the eight screws  
(see Figure 2-4)  
4.  
5.  
When the PCM-9679 is mounted in the panel, plug and press the  
adapter into the socket (see Figure 2-4))  
Some screws on the left connect the I/O adapter to the PC, and also  
connect the adapter to the PCM-9679. Screw the screws into the  
panel..  
Note:  
You may change the jumper settings for RS-  
232/422/485 before installing the PCM-9679  
and I/O adapter  
20 PPC-L106T User Manual  
 
Figure 2.4: Installing/removing the PCM-9679 & I/O adapter  
Chapter 2 System Setup 21  
22 PPC-L106T User Manual  
3
The Engine of the  
PPC-L106T (PCM-9679)  
Sections include:  
Introduction  
Features  
Jumpers and Connectors  
CMOS clear  
Watchdog timer configuration  
COM2 RS-232/422/485setting  
Chapter 3 The Engine of the PPC-L106T  
(PCM-9679)  
3.1 Introduction  
The PCM-9679 is a highly reliable single board computer based on the  
AMD LX800 CPU. It offers built-in functionality comparable to a com-  
plete industrial PC system, including a VGA/LCD controller, network  
communications, CompactFlash disk in a small 8" x 5.75" form factor.  
For maximum performance, the PPC-L106T also supports a DDR  
SODIMM socket that can accept up to 1024 MB memory. On-board fea-  
tures include an Ethernet interface, audio interface, socket for Compact-  
Flash card, Enhanced IDE interface that supports the Ultra DMA  
protocol, one parallel port, four serial ports (RS-232 and RS-232/422/  
485) with DB-9 connectors, and a mini-DIN PS/2 keyboard/mouse inter-  
face. An SVGA/LCD display controller (for LCD and CRT displays)  
allows LCD screen resolutions up to 800 x 600 @ 256 K colors.  
The PCM-9679 complies with the "Green Function" standard and sup-  
ports three types of power saving features: Normal, Doze and Sleep  
modes.  
The display type configuration is done through software. A single Flash  
chip holds the system BIOS and the VGA BIOS. This minimizes the  
number of chips and eases configuration. You can change the display  
BIOS simply by programming the Flash chip.  
Flash memory also offers faster data access and longer MTBF than  
mechanical disk drives and is an ideal solution for critical commercial or  
industrial applications. The watchdog timer ensures the system will be  
reset if it stops due to a program bug or EMI problem.  
24 PPC-L106T User Manual  
   
3.2 Features  
• Ultra-compact size single board computer as small as a 3 1/2" hard  
disk drive (145 mm x 102 mm)  
• On-board AMD LX800 CPU  
• Up to 1024 MB system memory via an SODIMM (DDR)  
• On-board VGA/LCD controller  
• On-board 10/100Base-T Ethernet interface (dual LAN Optional)  
• Supports on-board CompactFlash™ socket  
• Built-in Enhanced IDE (AT bus) hard disk drive interface  
• Four serial ports: three RS-232, one RS-232/422/485 or infared select-  
able  
• Supports One Mini PCI socket  
• Supports 4 USB 2.0 (2 external, 2 internal)  
• Supports 8 bit GPIO  
Chapter 3 System Setup 25  
 
3.3 Jumpers and Connectors  
3.3.1 Setting jumpers  
You can configure your panel PC to match the needs of your application  
by setting jumpers. A jumper is the simplest kind of electrical switch. It  
consists of two metal pins and a small metal clip (often protected by a  
plastic cover) that slides over the pins to connect them. To “close” a  
jumper, you connect the pins with the clip. To “open” a jumper you  
remove the clip. Sometimes a jumper will have three pins, labeled 1, 2,  
and 3. In this case, you would connect either pins 1 and 2 or pins 2 and 3.  
The jumper settings are schematically depicted in this manual as follows:  
open  
closed  
closed 2-3  
A pair of needle-nose pliers may be helpful when working with jumpers.  
open  
closed  
closed 2-3  
If you have any doubts about the best hardware configuration for your  
application, contact your local distributor or sales representative before  
you make any changes.  
26 PPC-L106T User Manual  
   
3.3.2 Jumpers  
The table below lists the function of each of the board’s jumpers.  
Table 3.1: Jumpers and their functions  
S1  
Reset Button  
J2  
SMBUS Power Setting  
CMOS Clear  
J3  
J4  
AT/ATX Setting  
J6  
COM2 RS232/422/485 Setting  
COM3/4 Pin9 output type setting  
Battery Connector  
J7  
BT1  
SLOT1  
PCI/ISA bus expansion connector  
3.3.3 Connectors  
The table below lists the function of each of the board's connectors.  
Table 3.2: Panel PC connectors  
Label  
J1  
Function  
Inverter power connector  
Flat panel display connector  
Primary IDE hard drive connector  
Keyboard connector  
J2  
J3  
J4  
J5  
Internal touchscreen connector  
SODIMM socket  
CN1  
CN2  
CN3  
CN4  
CN5  
CN6  
CN7  
CN8  
CN10  
CN20  
PS1  
JS2  
CompactFlash Disk secondary IDE connector  
CD IN  
I/O board connector  
I/O board connector  
Power FAN power connector  
External KBT2  
CPU FAN power connector  
Power Switch  
Speaker and Microphone connector (Reserved)  
Power test connector (Reserved)  
Brightness VR (Reserved)  
Chapter 3 System Setup 27  
   
TOUCH-(COM4)  
SMBUS  
CN3  
H1  
H3  
H2  
J2  
J2  
SMB_PWRSEL  
INVERTER  
U12  
1
2
3
4
5
6
7
8
9
1011121314151617  
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
GPIO  
CN7  
CN6  
CN9 IDE  
H4  
INTERNAL USB  
J3  
J4  
J3  
Clear CMOS  
CN11  
CN13  
IAS-5V/  
PWR_LED  
H5  
-12VINPUT  
Reset Button  
BT1  
H6  
CN12  
J4  
AT/ATX Sel  
CN14 MIO-(USB+COM3)  
SLOT1  
S1  
SLOT1  
CN16  
INTERNAL  
AUDIO OUT  
CN17  
J7  
INTERNAL LAN  
J6  
CN19  
CN18  
INTERNAL  
SPAKER  
H9  
H8  
BT1  
J6  
J7  
Figure 3.1: Jumpers on the PPC-L106T motherboard  
CN3  
CN2  
CN1 CN5  
TOUCH-(COM4)  
SMBUS  
CN3  
H1  
H3  
H2  
J2  
SMB_PWRSEL  
INVERTER  
CN4  
U12  
1
2
3
4
5
6
7
8
9
1011121314151617  
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
GPIO  
CN7  
CN6  
CN7  
CN8  
CN6  
CN9 IDE  
H4  
CN9  
INTERNAL USB  
J3  
Clear CMOS  
CN11  
CN11  
CN13  
CN12  
CN13  
IAS-5V/  
PWR_LED  
H5  
-12VINPUT  
Reset Button  
BT1  
H6  
CN12  
J4  
AT/ATX Sel  
CN14 MIO-(USB+COM3)  
SLOT1  
CN16  
INTERNAL  
AUDIO OUT  
CN17  
J7  
INTERNAL LAN  
J6  
CN17  
CN19  
CN18  
INTERNAL  
SPAKER  
H9  
H8  
CN19  
CN18  
CN21  
CN20  
Figure 3.2: Connectors on the PPC-L106T motherboard  
28 PPC-L106T User Manual  
3.4 CMOS Clear for External RTC (J3)  
Warning! To avoid damaging the computer, always turn off  
the power supply before setting “Clear CMOS”.  
Set the jumper back to “Normal operation” before  
turning on the power supply.  
This jumper is used to erase CMOS data and reset system BIOS informa-  
tion.  
The procedure for clearing CMOS is:  
1.  
2.  
3.  
4.  
Turn off system.  
Short pin 2 and pin 3.  
Return jumper to pins 1 and 2.  
Turn on the system. The BIOS is now reset to its default setting.  
Table 3.3: CMOS clear (J3)  
*Normal operation  
Clear CMOS  
* default setting  
3.5 COM Port Interface (J6, J7)  
The panel PC provides four serial ports (COM1, 3, 4: RS-232; COM2:  
RS-232/422/485) in one COM port connector.  
3.5.1 COM2 RS-232/422/485 setting (J6)  
COM2 can be configured to operate in RS-232, RS-422, or RS-485 mode.  
This is done via J6.  
Chapter 3 System Setup 29  
     
Table 3.4: COM2 RS-232/422/485 setting (J6)  
*RS-232  
RS-422  
RS-485  
* default setting  
The IRQ and the address ranges for COM1, 2, 3, and 4 are fixed. How-  
ever, if you wish to disable the port or change these parameters later you  
can do this in the system BIOS setup. The table overleaf shows the  
default settings for the panel PC’s serial ports.  
COM1 and COM2 are one set. You can exchange the address range and  
interrupt IRQ of COM1 for the address range and interrupt IRQ of  
COM2. After exchanging, COM1's address range is 3F8 ~ 3FF and its  
request IRQ is IRQ4: and COM2's address range is 2F8 ~ 2FF and its  
interrupt IRQ is IRQ3.  
COM3 and COM4 are another set. Their address and IRQ is the same as  
the COM1/COM2 set  
30 PPC-L106T User Manual  
Table 3.5: Serial port default settings  
Port  
Address Range  
Interrupt  
COM1  
COM2  
COM3  
COM4  
3F8 ~ 3FF  
2F8 ~ 2FF  
3E8 ~ 3EF  
2E8 ~ 2EF  
IRQ4  
IRQ3  
IRQ10  
IRQ5  
3.5.2 COM3/COM4 pin 9 output setting (J7)  
Table 3.6: COM3/4 pin 9 settings (J7)  
*Normal operation +5 V output  
+12 V output  
*default setting  
Chapter 3 System Setup 31  
 
32 PPC-L106T User Manual  
A
I/O Pin Assignments  
Sections include:  
Chapter A I/O Pin Assignments  
A.1 Keyboard connector (CN5-1)  
Table A.1: Keyboard connector  
Pin  
1
Signal  
KB_DT  
N/A  
2
3
GND  
+5 V  
4
5
KB_CK  
N/A  
6
A.2 Mouse connector (CN5-2)  
Table A.2: Mouse connector  
Pin  
1
Signal  
MS_DT  
N/A  
2
3
GND  
4
+5 V  
5
MS_CK  
N/A  
6
42 PPC-L106T User Manual  
     
A.3 VGA connector (CN6)  
Table A.3: VGA connector  
Pin  
1
Signal  
RED  
6
2
GREEN  
BLUE  
N/A  
1
2
3
4
5
11  
12  
13  
14  
15  
3
4
5
GND  
GND  
GND  
GND  
N/A  
6
7
10  
8
9
10  
11  
12  
13  
14  
15  
GND  
N/A  
N/A  
HSYNC  
VSYNC  
N/A  
A.4 COM1 RS-232 serial port (CN1-2)  
Table A.4: COM1 RS-232 serial port  
Pin  
1
Signal  
DCD  
RxD  
TxD  
DTR  
GND  
DSR  
RTS  
CTS  
RI  
1
2
3
4
5
6
2
7
8
9
3
4
5
6
7
8
9
Appendix A I/O Pin Assignments 43  
   
A.5 COM3 RS-232 serial port connector (CN2-1)  
Table A.5: COM3 RS-232 serial port  
Pin  
1
Signal  
DCD  
RxD  
TxD  
DTR  
GND  
DSR  
RTS  
CTS  
RI  
1
2
3
4
5
6
7
8
9
2
3
4
5
6
7
8
9
A.6 COM4 RS-232 serial port connector (CN2-2)  
Table A.6: COM4 RS-232 serial port  
Pin  
1
Signal  
DCD  
RxD  
TxD  
DTR  
GND  
DSR  
RTS  
CTS  
RI  
2
3
4
5
6
7
8
9
44 PPC-L106T User Manual  
   
A.7 COM2 Connector  
Table A.7: COM2  
Pin  
1
RS-232  
DCD  
RX  
RS-422  
TX-  
TX+  
RX+  
RX-  
GND  
---  
RS-485  
DATA-  
DATA+  
---  
2
3
TX  
4
DTR  
GND  
DSR  
RTS  
CTS  
RI  
---  
5
---  
6
---  
7
---  
---  
8
---  
---  
9
---  
---  
Appendix A I/O Pin Assignments 45  
 
A.8 Parallel port connector (CN1-1)  
Table A.8: Parallel port connector  
Pin  
1
Signal  
STROBE*  
D0  
1
2
14  
2
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
3
D1  
3
4
4
D2  
5
5
D3  
6
7
6
D4  
8
7
D5  
9
10  
11  
12  
13  
8
D6  
9
D7  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
ACK*  
BUSY  
PE  
SLCT  
AUTOFD*  
ERR*  
INIT*  
SLCTINI*  
GND  
GND  
GND  
GND  
GND  
GND  
GND  
GND  
* active low  
46 PPC-L106T User Manual  
 
A.9 GPIO Connector (Default: No Load)  
Table A.9: CN7 GPIO  
Pin  
1
Signal  
+V5  
Pin  
2
Signal  
GPIO4  
GPIO5  
GPIO6  
GPIO7  
GND  
3
GPIO0  
GPIO1  
GPIO2  
GPIO3  
4
5
6
7
8
9
10  
A.10 USB 3 / USB 4 Connector (Internal)  
Table A.10: CN12 Internal USB 3 / USB 4  
Pin  
1
Signal  
Pin  
2
Signal  
+V5_USB1  
USB2_Z_P+  
USB2_Z_P-  
GND  
+V5_USB1  
USB3_Z_P+  
USB3_Z_P-  
GND  
3
4
5
6
7
8
9
GND  
Appendix A I/O Pin Assignments 47  
   
A.11 SMBUS Connector (Default :No Load)  
1
2
3
4
Table A.11: CN5 SMBUS Input  
Pin  
1
Signal  
+V_SMB  
GND  
2
3
SMB_A_CLK  
SMB_A_DAT  
4
48 PPC-L106T User Manual  
 

Hanns G HH181 User Manual
Gear Head Computer Keyboard KP3200CW User Manual
Frigidaire FGGC3045K User Manual
EverFocus TFT LCD MONITOR EN 75084C User Manual
Cypress STK11C68 User Manual
Cisco Systems Computer Hardware 1130AG User Manual
Bosch Appliances PCL 785 FAU User Manual
AT T 2256 User Manual
Adesso WKB 2000BA User Manual
Acer P203W User Manual