AMD CS5535 User Manual

AMD Geode™ GX Processor/  
CS5535 Companion Device  
GeodeROM Porting Guide  
April 2006  
Publication ID: 32430C  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
Contents  
32430C  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
3
32430C  
Contents  
4
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
32430C  
List of Figures  
6
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
32430C  
List of Tables  
8
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
Overview  
32430C  
1.0Overview  
1
1.1  
Introduction  
This document describes the changes needed for GeodeROM and other BIOSs to support the AMD Geode™ GX proces-  
sor and the AMD Geode™ CS5535 companion device. GeodeROM requires modifications for hardware initialization and  
specific implementations.  
Each section targets the GeodeROM changes needed to support the GX processor/CS5535 device system. Where appro-  
priate, the changes list the “Entry Conditions” that briefly describe the machine state required to execute that function, as  
well as some pseudo code for implementing the changes.  
For more information on GeodeROM, see the AMD Geode™ GeodeROM Functional Specification (publication ID 32087).  
1.2  
Assumption  
The following assumption must be made clear during the design phase:  
GeodeROM expects all memory has a serial presence detect (SPD) to determine characteristics for memory controller ini-  
tialization. If a SPD is not present, GeodeROM outputs a POST code and halts, unless customizations have been made for  
the platform.  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
9
     
32430C  
Assumption  
10  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
Model Specific Registers  
32430C  
2.0Model Specific Registers  
2
There are two ways to read or write Model Specific Registers (MSRs) in a Geode™ GX processor system. Software run-  
ning on the processor can use the RDMSR and WRMSR instructions, and modules within the processor can use the  
GeodeLink™ MSR transactions. The second method allows debug modules, such as the System Navigator from FS (First  
2
Silicon Solutions), to program MSRs.  
All MSRs are 64 bits wide. The MSR addresses are 32 bits, where each unique address refers to a 64-bit data quantity.  
To communicate with modules on the GeodeLink interface, the address of that module must be known. Addresses are  
obtained by either scanning the GeodeLink interface or having prior knowledge of the chip topology. This is discussed in  
RDMSR:  
Input  
ECX - Address to read.  
Output  
EDX:EAX - 64 bits data returned.  
WRMSR:  
Input  
ECX - Address to write.  
EDX:EAX - 64 bits data written.  
Output  
None.  
2.1  
Example MSR Transaction  
Read and write extended CPUID registers.  
This example will change the CPUID.  
RDMSR:  
Load MSR specified by ECX into EDX:EAX.  
WRMSR:  
Write the value in EDX:EAX to MSR specified by ECX.  
MSR_CPUID0 EQU 00003000h  
MSR_CPUID1 EQU 00003001h  
mov  
RDMSR  
mov  
ecx, MSR_CPUID0  
edx, ‘cdeR’  
; get values  
; write edx:eax to MSR in ecx. No change to eax.  
WRMSR  
mov  
RDMSR  
mov  
ecx, MSR_CPUID1  
edx, ‘duol’  
; No change to eax  
WRMSR  
; Done  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
11  
   
32430C  
Model Specific Registers  
12  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
GeodeLink™ Architecture  
32430C  
3.0GeodeLink™ Architecture  
3
GeodeLink™ architecture connects the internal modules of the AMD Geode™ GX processor using the data channels pro-  
vided by GeodeLink Interface Units (GLIUs). GeodeLink modules are connected to GLIU ports 1 – 7 as shown in Figure 3-  
1. Port 0 is always the GLIU itself. GLIUs can be chained together and up to a maximum of six GLIUs can be connected  
allowing for 32 modules.  
GLMC  
1
CPU Core  
3
0
7
4
Not Used  
DC  
GLIU0  
6
5
VP  
GP  
2
GLIU0 GLIU1  
AMD Geode™  
GX Processor  
ACC  
5
1
Not Used  
USBC1  
6
DD  
2
0
4
7
3
Not Used  
GLCP  
GLCP  
ATAC  
GLIU1  
GLIU  
7
3
5
6
0
2
Not Used  
4
GIO  
USBC2  
1
AMD Geode™  
CS5535  
Companion  
Device  
GLPCI  
GLPCI  
PCI Bus  
Figure 3-1. GeodeLink™ Architecture Topology  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
13  
     
32430C  
GeodeLink™ Architecture  
3.1  
GeodeLink™ MSR Addressing  
The GX processor’s MSRs are addressed from the source module to the port of the target module. The topology of the GX  
processor must be understood to derive the address. An MSR address is parsed into two fields, the port address (18 bits)  
and the index (14 bits). The port address is further parsed into six 3-bit channel address fields. Each 3-bit field represents,  
from the perspective of the source module, the GLIU channels that are used to get to the destination module, starting from  
the closest GLIU to the source (left most 3-bit field), to the farthest GLIU (right most 3-bit field). When the GLIU gets the  
cycle, it reads the three MSBs of the address register, shifts those three bits of the 18 MSBs of the address register off, and  
passes the transaction to the port indicated by the next three bits.  
MSR addresses that are outside the module address spaces are invalid; meaning RDMSR/WRMSR instructions attempting  
to use the address within the CPU core will cause a General Protection Fault. Unimplemented MSR accesses not in periph-  
eral modules go to the bit bucket.  
3.1.1  
Addressing Example  
GX Processor GeodeLink Modules/Addresses  
Source: CPU Core -> Destination: GeodeLink Control Processor (GLCP)  
2.3.0.0.0.0 -> 4C00xxxxh  
CS5535 Companion Device GeodeLink Module/Addresses  
Source: CPU Core -> Destination: SB_GLCP  
2.4.2.7.0.0 -> 5170xxxxh  
GLPCI acts like another GLIU  
3.2  
Descriptors  
Descriptors are used to route memory or I/O resources through GLIUs to a GX processor module. Memory and I/O  
addresses that do not have descriptors are subtractively decoded through the GLIUs and out to the PCI. It is important that  
no descriptors overlap each other. The result is indeterminate.  
3.2.1  
Memory Descriptor Types  
Range - Covers a memory range in 4 KB granularity.  
Range Offset - Covers a memory range in 4 KB granularity with the destination address translated by an offset.  
Base Mask - Covers a memory range that is a power of 2 in size.  
Base Mask Offset - Covers a memory range that is a power of 2 in size with the destination address translated by an  
offset.  
Swiss Cheese - Covers a 256 KB region split into 16 KB pieces to a module or the subtractive port.  
3.2.2  
I/O Descriptor Types  
Base Mask - Covers an I/O range that is a power of 2 in size.  
Swiss Cheese - Covers an 8-byte region split into 1-byte pieces to a module or the subtractive port.  
14  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
   
Initialization  
32430C  
4.0Initialization  
4
4.1  
Processor Initialization  
The AMD Geode™ GX processor contains many of the components normally found in system support chipsets.  
GeodeROM must set up these components, including the DRAM controller, L1 cache controller, clock control, and PCI con-  
troller as well as some proprietary systems like GeodeLink™ architecture.  
This chapter contains descriptions and some pseudo code for GX processor-specific code sequences in GeodeROM. The  
modifications are grouped into CPU core initialization, DRAM controller initialization, GeodeLink interface initialization, PCI  
bus initialization, and miscellaneous other initializations/changes.  
4.1.1  
Set Clocks and Reset  
Register: GLCP_SYS_RSTPLL (GX GLCP MSR Address 4C000014h)  
The GX processor has separate clocks for the CPU core and GeodeLink interface. These clocks are derived from the sys-  
tem PLL, which is driven by the PCI clock. At power-on, these clocks default to a safe value. Setting the clock registers and  
doing a reset will re-clock the GX processor.  
The clocks are controlled by three divisors as shown in Figure 4-1. The Feed-back Divisor (FbDIV) in the PLL sets  
sppl_raw_clk. Sppl_raw_clk is divided by the GeodeLink Divisor (MDIV) and the CPU Divisor (VDIV) to derive GeodeLink  
clock and CPU clock. Sppl_raw_clk must be between 300 MHz and 800 MHz. The GeodeLink clock is used to clock the  
memory. Therefore, the GeodeLink clock should never be greater than the speed and type of the system memory.  
All the divisor bits, software bits, memory type bit, and reset bits are located in the GLCP_SYS_RSTPLL register. Once the  
divisors and memory type (DDR/SDR) are set, the BIOS sets a reset flag and resets the CPU to continue initialization at the  
desired CPU speed.  
GeodeROM sets the clocks based on jumper settings that are interpreted to match SKUs defined for that version of the  
CPU. SKUs are defined by PCI speed, memory type (SDR or DDR), and the jumper setting. GeodeROM can also use  
FbDIV, MDIV, and VDIV values set by the user in CMOS for debugging.  
If there is an incorrect setting in CMOS setup and the system cannot boot three times in a row, GeodeROM resets CMOS  
to the defaults.  
See Figure 7-4 on page 33 for example reset and system clock logic.  
GLIU Clock  
MDIV  
SYSREF  
(PCI Clock)  
System PLL  
300 - 800 MHz  
Clock  
spll_raw-clk  
0 - 66 MHz  
Clock  
FbDIV  
CPU Core Clock  
VDIV  
Figure 4-1. Clock Control  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
15  
       
32430C  
Initialization  
4.1.2  
Calculating Processor Speed  
Entry Conditions:  
Stack and No-Stack versions required.  
8254 timer available (port 61).  
Procedure:  
Utilize the Real Time Stamp Counter (RTSC).  
Disable the L1 cache.  
Set up a channel of the 8254 Timer chip to count for a predetermined amount of time.  
Read the CPU RTSC and save the initial count value.  
Poll counter and wait for it to roll over.  
Read the CPU RTSC and save as the final count.  
Subtract the initial value of the RTSC from the final value.  
EDX:EAX now contains the number of clock ticks in the predetermined amount of time.  
To get the value in MHz, divide the number of clocks by the time represented in microseconds (i.e., 5 ms = 5000).  
4.1.2.1 CPU Identification  
The CPUID check should be done as soon as possible. Use the CPUID instruction.  
Check the Major and Minor Revision fields located in the GLCP_CHIP_REVID register (MSR Address 4C000017h[7:0]) for  
the silicon revision.  
4.1.3  
Memory Controller Initialization  
Registers:  
MC_CF07_DATA (MSR Address 2000018h)  
MC_CF8F_DATA (MSR Address 2000019h)  
MC_CFCLK_DBUG (MSR Address 200001Dh)  
The memory controller in the GX processor supports SDRAM and DDR memory. The memory controller and the RAM are  
programmed via settings read from the SPD. The SPD is required for detection of PC66, PC100, PC133 and DDR RAM.  
In the case of a closed system, where the RAM is soldered to the motherboard and there is no SPD, memory settings can  
be stored in CMOS for initialization.  
The SDRAM clock is set up prior to reset by the clock initialization.  
Address, bank, registered/unbuffered, and other values read from the SPD.  
Size memory in DIMM socket(s).  
Program Memory Controller.  
Set default refresh to an appropriate value.  
16  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
Initialization  
32430C  
4.1.3.1 Size Memory  
Entry Conditions:  
4 GB descriptor in FS Core register.  
Procedure:  
For each DIMM:  
Set the following in the MC_CF07_DATA register MSR Address 20000018h):  
— Module Banks per DIMM  
– SPD byte 5: Number of DIMM Banks  
— Banks per SDRAM device  
– SPD byte 17: Number of Banks on SDRAM device  
— DIMM size - Size = Density * Banks  
– SPD byte 5: Number of DIMM Banks  
– SPD byte 31: Module Bank Density  
— Page size - Page size = 2^# Column Addresses  
– SPD byte 4: Number of Column Addresses  
Set CAS Latency in MC_CF8F_DATA register (MSR Address 20000019h):  
— SPD byte 18: CAS Latency  
Turn on the memory interface in MC_CFCLK_DBUG bit MASK_CKE[1:0] (MSR Address 2000001Dh[9:8]).  
— Do 12 refreshes (CF07_PROG_DRAM) for the Memory Controller to synchronize.  
— Set the refresh rate of the DIMM – SPD byte 12: Refresh Rate/Type.  
— Load RDSYNC counter with sync value.  
Note: See the AMD Geode™ GX Processors Data Book (publication ID 31505) for bit descriptions and allocation.  
4.1.4  
Entry Conditions:  
4 GB descriptor in FS Core register.  
All memory configured.  
Procedure:  
Test Extended DRAM  
Set GLIU descriptor to allow writes to memory.  
Make sure interface is turned on in MC_CFCLK_DBUG bit MASK_CKE[1:0] (MSR Address 2000001Dh[9:8]).  
Determine total amount of memory by doing a read/write test.  
For each 1 MB block of memory:  
1) Walk a 1 through data bus at first location of block.  
2) Walk a 0 through data bus at first location of block.  
3) Check for stuck address line in the block.  
Continue test if no memory present for debug purposes.  
4.1.5  
GeodeLink™ Modules Initialization  
Descriptors routing memory and I/O for GX processor modules are initialized by GeodeROM and Virtual System Architec-  
ture™ (VSA) technology. GeodeLink modules that are virtualized by VSA technology and use PCI memory or PCI I/O,  
report that resource in the virtual PCI header. The GLIU is configured with MSRs like all GX processor modules.  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
17  
32430C  
Initialization  
4.1.5.1 GLIU Descriptors Initialization  
Register:  
P2D_BM, P2D_BMO, P2D_R, P2D_RO, P2D_SC (GLIU0 MSR Address 10000020h-1000003Fh, GLIU1 MSR  
Address 40000020h-1000003Fh)  
IO_BM, IO_SC (GLIU0 MSR Address 100000E0h-100000FFh, GLIU1 MSR Address 400000E0h-400000FFh)  
Set up system memory map with GeodeLink Descriptors and Region Control Registers (RConfs). Descriptors and RConfs  
must match each other. These register maps will look like the memory map from INT 15h AX = E820.  
The responsibility of setting Descriptors and RConfs is split between GeodeROM and VSA technology. GeodeROM han-  
dles settings for system memory and VSA memory. Then the responsibility is handed off to VSA technology once it is  
loaded to handle all other memory and I/O routing. This is most notable in the frame buffer initialization. See Memory Map,  
Figure 7-2 on page 31 for a pictorial representation.  
4.1.5.2 GLIU Priority Initialization  
Each GeodeLink module has standard MSRs. GLD_MSR_CONFIG is one of the standard registers located at address  
2001h in the GX processor and 0001h in the CS5535 companion device. Two fields in some of the GLD_MSR_CONFIG  
registers can affect the module priority: Priority Level (PRI0) and Priority Domain (PID). These values default to zero. In the  
case of data starvation or saturation on the GLIU, GeodeROM can adjust these values as recommended by AMD.  
4.1.5.3 Cache Setup  
The GX processor has a 16 KB instruction cache and a 16 KB data cache. The cache is enabled through register CR0 and  
both caches can be disabled through MSRs regardless of the CR0 state.  
4.1.5.4 Region Configuration  
Region Configuration MSRs are used to describe the caching properties of each memory region. Unlike descriptors,  
RConfs are designed to overlap. The Default Region Configuration Properties register (CPU Core MSR Address  
00001808h) contains the base settings, and RConfs for the shadow area and other special regions supersede its setting.  
Example Default Region Configuration Properties:  
128 MB memory in the system 8 MB is used for frame buffer and 256 KB is used for VSA technology.  
0x1808 = 0x25FFFC02 0x1077DF00  
The Default Region Configuration Properties register, shown in Table 4-1, is the main register for GX processor cache set-  
tings.  
Table 4-1. Default Region Configuration Properties Bit Descriptions  
Bit  
Name (Note)  
Description  
63:56  
ROMRP  
ROM Region Properties. Region properties for addresses greater than ROMBASE (bits  
[55:36]).  
55:36  
35:28  
27:8  
7:0  
ROMBASE  
DEVRP  
ROM Base Address. Base address for boot ROM. This field represents A[32:12] of the  
memory address space, for 4 KB granularity.  
SYSTOP to ROMBASE Region Properties. Region properties for addresses less than  
ROMBASE (bits 55:36]) and addresses greater than or equal to SYSTOP (bits [27:8]).  
SYSTOP  
SYSRP  
Top of System Memory. Top of system memory that is available for general processor  
use. The frame buffer and other private memory areas are located above SYSTOP.  
System Memory Region Properties. Region properties for addresses less than SYS-  
TOP (bits [27:8]). Note that Region Configuration 000A0000h-000FFFFFh takes prece-  
dence over SYSRP.  
Note: Region Properties: 7:6 = Reserved; 5 = Write Serialize; 4 = Write Combine; 3 = Write-through; 2 = Write Protect;  
1 = Write Allocate; 0 = Cache Disable.  
18  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
 
Initialization  
32430C  
Registers:  
CR0  
RCONF MSRs: CPU Core MSR Address 00001808h-00001817h  
Instruction Memory Configuration Register: CPU Core MSR Address 00001700h  
Data Memory Configuration Register: CPU Core MSR Address 00001800h  
Entry Conditions:  
None  
Procedure:  
IF <L1 cache requested>  
Setup the Default Region Configuration Properties and any other RCONFs required.  
Write Cache Disable and Not Write-Through bits (bits [30:29]) in the CR0 register.  
WBINVD  
ENDIF  
Note: See Figure 7-2 on page 31 for a pictorial presentation.  
GLPCI Regions  
The GLPCI has similar MSRs to the CPU Core Region Configuration registers for inbound transactions. These memory  
regions control the memory hole from 6460 KB to 1 MB. Six flexible region MRSs are assigned: Memory Region 0 Configu-  
ration (R0) through Memory Region 5 Configuration (R5).  
Descriptor Allocation  
Register: PHY_CAP (MSR Address GLIU0: 10000086h, GLIU1: 40000086h)  
Each GLIU descriptor allocation is defined in the PHY_CAP register.  
Descriptor  
MSR Address  
GLIU0  
GLIU1  
P2D_BM  
10000020h  
10000021h  
10000022h  
10000023h  
10000024h  
10000025h  
10000026h  
10000027h  
10000028h  
10000029h  
1000002Ah  
1000002Bh  
1000002Ch  
00000000h-00007FFFh  
00080000h-0009FFFFh  
4FFFC000h-4FFFFFFFh  
000A0000h-000BFFFFh  
Not used by GeodeROM.  
Not used by GeodeROM.  
40400000h-4043FFFFh  
Not used by GeodeROM.  
00100000h-0E7BFFFFh  
50000000h-517FFFFFh  
4FFF8000h-4FFFBFFFh  
Not used by GeodeROM.  
C000C7FFh, E000FFFFh  
00000000h-00007FFFh  
00080000h-0009FFFFh  
4FFFC000h-4FFFFFFFh  
000A0000h-000BFFFFh  
Not used by GeodeROM.  
Not used by GeodeROM.  
40400000h-4043FFFFh  
Not used by GeodeROM.  
00100000h-0E7BFFFFh  
50000000h-517FFFFFh  
4FFF8000h-4FFFBFFFh  
Not used by GeodeROM.  
C000C7FFh, E000FFFFh  
P2D_BMO  
P2D_R  
P2D_RO  
P2D_SC  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
19  
32430C  
Initialization  
4.2  
AMD Geode™ CS5535 Companion Device Initialization  
The Geode™ CS5535 is a complete companion device to the GX processor. The Geode CS5535 incorporates the  
GeodeLink technology developed in the GX processor to make a transparent GeodeLink through the PCI to the CS5535  
device. The CS5535 companion device contains many of the components normally found on the SuperI/O chip.  
GeodeROM and VSA2 technology initialize these components, including the hard disk controller, USB controllers, GPIOs,  
RTC, SMBus, Local bus, and other legacy components. This chapter contains descriptions as well as some pseudo code  
for GX processor-specific code sequences in GeodeROM. The GX processor and CS5535 device do not implement com-  
plete PCI bus controllers, so GeodeLink modules that must be identified and configured by an operating system have their  
PCI configuration spaces virtualized by VSA.  
4.2.1  
Chipset ID  
Hardware PCI Header ID = 002A100Bh  
Virtual PCI Header ID = 002B100bh  
4.2.2  
Set ID Select (IDSEL)  
The CS5535 companion device number is changeable by a 32-bit, write once register located in I/O space 0. By default, the  
CS5535 is located at device 15 (IDSEL = AD25). To insure that it is not accidentally moved, it must be programmed very  
early in post. The External MSR Access Configuration Register (GX GLPCI MSR Address 50000201Eh) must match the  
device number to route MSR transactions across the PCI bus.  
Example:  
; set IDSEL  
mov eax, 02000000h  
; mov eax, 04000000h  
out 0000h, eax  
; IDSEL = AD25, device #15  
; IDSEL = AD30, device #20  
; set ExtMSR  
mov eax, 0F0F0F0Fh  
mov edx, 000F0F0Fh  
; mov eax, 14141414h  
; mov edx, 00141414h  
mov ecx, extMSR  
WRMSR  
; device #15  
; device #15  
; device #20  
; device #20  
4.2.3  
GLIU Initialization  
The CS5535 companion device contains one GLIU that connects up to six peripheral modules. The GLIU routes memory  
and I/O for the attached modules. Descriptors controlling memory and I/O for the attached modules are initialized by VSA  
technology. GeodeLink modules can be scanned for their identification. Non-legacy GeodeLink modules that must be visi-  
ble on the PCI bus will have PCI headers virtualized by VSA technology. The GLIU is configured with MSRs like all GX pro-  
cessor and CS5535 device modules.  
VSA technology is also responsible for the Geode CS5535 descriptor allocation.  
4.2.4  
Diverse Device Initialization  
The Diverse Device (DD) is a collection of new and legacy devices that are located in I/O space and connected by the Local  
bus. It is also the subtractive decode port of the CS5535. Any memory or I/O not claimed by the DD is passed on to the Low  
Pin Count (LPC) bus. The CS5535 has provided complete flexibility to put non-legacy Local bus devices at any I/O location  
by implementing Local BARs (LBARs). The following subsections show recommended locations in I/O space to set the  
LBARs. Devices that may be used before VSA is initialized will be set by GeodeROM.  
20  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
 
Initialization  
32430C  
4.2.4.1 IRQ Mapper  
Location:  
I/O 20-21 master Programmable Interrupt Controller (PIC), I/O A0-A1 slave PIC, I/O 4D0 edge/level  
PIC shadow register at MSR Address 51400034h  
The use of the IRQ Mapper LBAR is optional since it is always accessible via MSRs. The LBAR is for  
the Mask and Mapper (MM) and the extended PIC (XPIC).  
Description:  
Initialization:  
The IRQ Mapper is a combination of a Mapper and Mask (MM), an XPIC, and two Legacy 8259 compat-  
ible PICs (LPIC).  
At reset, the PIC subsystem comes up in legacy mode. VSA initializes the XPIC to generate ASMI from  
GPIOs. Devices on the XPIC are hard wired to Interrupt Groups (IG) in the MM and XPIC. The XPIC is  
hooked to the LPIC on interrupts [0:1], [3:15]. The rest (16:64) are hooked to ASMI.  
The XPIC has several incoming sources. They are IRQ, LPC, Y, and Z sources. The Y sources include software, USB, RTC  
alarm, audio, power management, NAND Flash, SMB, KEL, and UARTs. The Z sources include eight MFGPTs and eight  
GPIOs. During PCI scan, GeodeROM allocates memory, I/O, and interrupts to the PCI devices. This includes the virtual  
devices emulated by VSA. VSA is responsible for the setup of the XPIC mapper for the devices it is virtualizing.  
4.2.4.2 Keyboard Emulation Logic (KEL) 1+ 2  
Location:  
NA  
Description:  
Initialization:  
Used for A20 support as well as USB keyboard emulation.  
VSA technology.  
4.2.4.3 System Management Bus (SMBus)  
Location:  
6000h  
Description:  
SMBus is an industry standard two-wire serial interface. The SMBus is essentially an ACCESS.bus and  
is the interface used to read the DRAM SPD.  
Initialization:  
GeodeROM sets the LBAR with the desired location and the GPIOs for SMBus. The recommended  
address (SMBADDR) is 0EFh.  
4.2.4.4 GPIO and ICF  
Location:  
6100h  
Description:  
There are 23 GPIOs in Working mode and 5 in Standby mode. The GPIO registers are such that there is  
no need to do read/modify/writes. GPIO registers associated with bit settings are 32 bits. Thus, 16 GPIO  
may be changed at once. These are organized into Low and High banks. The Low bank deals with  
GPIOs 0 through 15 while the High bank deals with GPIOs 16 through 31.  
Be aware of specification update issue #113 in certain silicon revisions (as of this writing, see AMD  
Geode™ CS5535 Companion Device Specification Update Silicon Revision A3 (publication ID 31534)).  
After a suspend, writing the register can not be done atomically.  
Initialization:  
VSA technology will set and use GPIOs connected with SMIs.  
Many GPIOs are muxed with other signals and must be set up appropriately. There is a GPIO INT and  
Power Management Event (PME) Mapper that maps GPIOs to the PIC and power management sub-  
system.  
4.2.4.5 Multi Function General Purpose Timers (MFGPTs)  
Location:  
6200h  
Description:  
Timers are used by VSA mostly. The timers can set and be set by GPIOs. The timers can output to non-  
maskable interrupts and cause an ASMI through the XPIC with interrupts.  
Initialization:  
VSA technology.  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
21  
32430C  
Initialization  
4.2.4.6 ACPI  
Location:  
9C00h or other normal ACPI location.  
Description:  
Initialization:  
NA  
ACPI VSM  
4.2.4.7 Power Management Logic  
Location:  
9D00h put on the end of ACPI.  
Description:  
Initialization:  
NA  
VSA technology and ACPI VSM as needed.  
4.2.4.8 Flash Interface  
Location:  
4 LBARs for 4 Flash devices  
NA  
Description:  
Initialization:  
The default values for the LBARs are located in BDCFG.INC in the platform directory, but can be  
changed at Boot via setup. The Flash interface is configured in the code at ChipsetFlashSetup in  
CHIPSET.ASM based on the corresponding NVRAM values.  
4.2.4.9 Other Legacy DD Initialization  
Location:  
Default legacy definitions.  
Description:  
Initialization:  
Initialize COM ports, LPT ports, RTC.  
These devices are initialized in the same fashion as with a normal SuperI/O and CS5535. Any MSR reg-  
ister settings will be done in chipset individualization. GeodeROM can handle multiple devices and loca-  
tions by design.  
22  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
 
Initialization  
32430C  
4.2.4.10 DD I/O Locations  
Table 4-2. Diverse Device I/O Locations  
Location  
Device  
0020h  
0021h  
0060h  
0064h  
0070h  
0071h  
00A0h  
00A1h  
02E8h  
02F8h  
03E8h  
03F8h  
04D0h  
04D1h  
6000h  
6100h  
6200h  
6400h  
6500h  
6600h  
6700h  
9C00h  
9D00h  
PIC Master Command and Status  
PIC Master Command and Status  
USB - Keyboard and Mouse Data  
USB - Keyboard and Mouse Command and Status (KEL)  
RTC Address  
RTC Data  
PIC Slave Command and Status  
PIC Slave Command and Status  
UART/IR COM4  
UART/IR COM2  
UART/IR COM3  
UART/IR COM1  
PCI Level/Edge IRQ0-7  
PCI Level/Edge IRQ8-15  
SMBus  
GPIO and ICF  
General Purpose Timers  
Flash BAR  
Flash BAR  
Flash BAR  
Flash BAR  
ACPI - Subdivide to support GX processor and CS5535 companion device  
Power Management Logic - Placed at the end of ACPI  
4.2.5  
ATA-5 / Hard Drive Initialization  
Hard drive initialization is handled by a system ROM that is loaded by GeodeROM. The hard drive ROM contains the hard  
drive initialization, the PIO modes support, and the interrupt support.  
New to the hard drive ROM is the UDMA setup, so that default drivers may be used in some operating systems. The UDMA  
setup includes detecting the 80-conductor IDE cable for UDMA/66 support.  
4.2.6  
Universal Serial Bus (USB)  
There are two Universal Serial Bus Controllers (USBCs) each containing a GeodeLink™ Adapter, PCI Adapter, and USB  
Core blocks. The GeodeLink Adapter (GLA) translates GeodeLink transactions to/from Local bus transactions. The GLA  
interfaces to a 64-bit GLIU (GeodeLink Interface Unit) and a 32-bit Local bus. The GLA supports in-bound memory and I/O  
requests, which are converted by the PCI Adapter (PA) into PCI memory and I/O requests that target the USBC. It also sup-  
ports in-bound MSR transactions to the MSRs.  
4.2.7  
AC97 Audio Controller Initialization  
The audio codec is initialized by the native audio driver. The virtual PCI header contains the IRQ line. The IRQ is set  
through the regular PCI initialization and IRQ mapping.  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
23  
 
32430C  
Initialization  
4.2.8  
GeodeLink™ Control Processor Initialization  
The Geode CS5535 GLCP contains the diagnostic bus, the JTAG interface clock, south bridge control, and power manage-  
ment.  
4.3  
Virtual System Architecture™ Initialization  
Virtual System Architecture (VSA) is the System Management Mode (SMM) software. VSA virtualizes PCI BARs and head-  
ers for GeodeLink modules as well as its normal functions described in the AMD Geode™ GeodeROM Functional Specifi-  
cation (publication ID 32087).  
4.3.1  
Allocate Processor Frame Buffer and VSA2 Memory  
The GX processor employs a Unified Memory Architecture (UMA), meaning the frame buffer is allocated from the total sys-  
tem memory. The GeodeROM code programs the amount of system memory initially needed for VSA memory. VSA can  
adjust the descriptors once it is loaded. When internal video is enabled, VSA allocates the frame buffer and graphics  
descriptors. The amount of memory currently allowed for frame buffer use ranges from 4 to 16 MB.  
To inhibit operating system DRAM detection code from reporting the frame buffer as part of system memory, a GLIU offset  
descriptor is set to send transactions to the PCI bus and program Region Configuration Registers to set the region non-  
®
cacheable. This means that DOS, Windows , OS/2, and UNIX are never aware of the graphics memory portion of system  
memory. This mapping prevents unwanted access to the graphics frame buffer and other critical graphics information stored  
in this area. The memory is claimed in the Virtual PCI header.  
4.4  
PCI Bus Initialization  
The GX processor does not incorporate a standard PCI bus controller. The GX processor and CS5535 devices do not have  
PCI headers. VSA emulates all the PCI headers and the GeodeLink is configured to route memory and I/O for those mod-  
ules. This requires VSA to be initialized before PCI scan.  
For Virtual PCI headers, VSA sets GeodeLink descriptors and the Region Control Registers as requested by the modules  
during PCI scans.  
PCI scan supports interrupt mapping and PCI Bridge support. There is no plan for ISA PnP support at this time.  
The PCI controller configuration registers are accessed through PCI type one configuration access mechanism (using Ports  
CF8h and CFCh).  
24  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
   
Initialization  
32430C  
4.5  
Miscellaneous Initializations  
In addition to the previous processor initializations, the graphics card(s) must also be initialized.  
4.5.1 Initialize Graphics Subsystem  
There are two different modes: CRT and TFT. Graphics initialization needs to identify which kind of support is required by  
reading an MSR in the Video Processor.  
Entry Conditions:  
4 GB descriptor in FS core register.  
GeodeLink descriptors initialized.  
VSA initialized.  
First MB of DRAM functional.  
Interrupts enabled.  
DMA initialized.  
PCI bus functional.  
Procedure:  
IF <PCI graphics card exists> THEN  
Jump to PCI graphics BIOS for initialization.  
ELSEIF <ISA graphics card exists> THEN  
Jump to ISA graphics BIOS for initialization.  
ELSE <SoftVGA required by setup> THEN  
Initialize SoftVGA during VSA initialization  
Jump to integrated graphics BIOS for initialization  
ENDIF  
4.5.1.1 Monochrome Support  
GeodeROM includes the appropriate INT 10h support for monochrome video adapters.  
SoftVG needs an extra hole at B000h-B7FFh when a mono card is present.  
4.5.1.2 Dual Monitor Support  
GeodeROM provides dual monitor support. GeodeROM assumes that the external card is the primary graphics card and  
that the XpressGRAPHICS™ system is secondary.  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
25  
 
32430C  
Initialization  
26  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
Implementation  
32430C  
5.0Implementation  
5
5.1  
Implementation  
The following is a collection of implementation details to consider in the GeodeROM implementation phase.  
5.1.1 Clocking  
There are two clock inputs to the GX processor: the system PCI clock (SYSREF) used to derive the Core clock, and the  
GeodeLink™ clock used for the memory clock. The Dot clock is used for video display control. The Core and GeodeLink  
clocks can be programmed and restarted by reseting the GX processor.  
5.1.2  
Scratchpad Initialization  
The scratchpad is no longer needed either for BLT buffers or by the audio code for variable storage. The scratchpad is not  
supported in the GX processor CPU Core.  
5.1.3  
Post Codes  
Post codes are sent out to port 80 throughout GeodeROM. A Post codes list is available in the AMD Geode™ GeodeROM  
Functional Specification (publication ID 32087) to help users debug their problems.  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
27  
   
32430C  
Implementation  
28  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
Setup Options  
32430C  
6.0Setup Options  
6
Initial configuration is set in the configurator at build time. Based on those settings, there are some setup options at runtime  
that are platform specific. Check your platform specification for more details.  
Desired Setup Options:  
Clock configuration - complete control of system PLLs  
— Default: Use strap setting for core. GeodeLink™ interface frequency is calculated based on DIMM type.  
PM settings  
— Default: Off  
Audio enable/disable  
— Default: Enabled  
Video Primary/Secondary/Disabled  
— Default: Secondary  
Video Memory Size  
— Default: 24 MB  
Cache enable/disable  
— Default: Write Back  
MTest enable/disable  
— Default: disabled  
LPT enable/disable  
— Default: 378  
Note: If a setting is incorrect and the system cannot boot three times, CMOS is reset to the default setup options.  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
29  
 
32430C  
30  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
Memory Map  
32430C  
7.0Memory Map  
7
Figures 7-1, 7-2, and 7-3 show the system memory. Figure 7-1 is the GLIU Descriptor Map, Figure 7-2 shows the Core  
Cache descriptors, and Figure 7-3 on page 32 shows the Core cache region configurations.  
Figure 7-4 on page 33 shows the flow of GeodeROM in the GX processor/CS5535 system.  
Memory Descriptors  
BM - Base Mask  
R - Range  
BMO - Base Mask Offset  
RO - Range Offset  
SC - Swiss Cheese No Swiss Cheese Offset  
Figure 7-1. GLIU Descriptor Map  
FFFFFFFFh (4 GB)  
FFFC0000h  
ROM  
Subtractive to PCI  
Subtractive to PCI  
Subtractive to PCI  
Subtractive to PCI  
Frame Buffer Offset  
Video Descriptors  
(RO, VP + GP + DC)  
Memory Mapped Frame Buffer  
Memory Mapped Video Registers  
Memory Mapped VSA  
50000000h  
40400000h  
VSA Offset  
subtracted from  
Extended Memory  
Subtractive to PCI  
Top of DRAM  
Frame Buffer Descriptors  
(RO, GLMC)  
Frame Buffer  
VSA  
SMM Descriptor (RO, GLMC)  
VSA and Video Memory  
Subtractive to PCI  
Top of System  
(OS) RAM  
SysTop Descriptor (R, GLMC)  
Extended Memory  
Two Shadow Descriptor (SC, GLMC)  
A0000h - DFFFFh, E0000h-11FFFh  
Two Conv Desc (BM, MC)  
0-7FFFFh, 80000h-9FFFFh  
System and Option ROMs  
A0000h - 100000h (640 KB - 1 MB)  
Conventional Memory  
Figure 7-2. CPU Core Cache Descriptors  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
31  
       
32430C  
Memory Map  
RCONF_DEFAULT ROMRC  
RCONF_DEFAULT ROMBASE  
ROM  
FFFC0000h  
PCI  
Memory Mapped  
PCI  
PCI  
PCI  
Memory Mapped Frame Buffer  
50000000h  
Memory Mapped Video Registers  
Memory Mapped VSA  
40400000h  
subtracted from  
Extended Memory  
RCONF_DEFAULT DEVRG  
PCI  
Top of DRAM  
Frame Buffer  
VSA  
VSA and Frame Buffer  
RCONF_SMM  
RCONF_DEFAULT SYSTOP  
PCI  
RCONF_DEFAULT SYSRC  
Top of System  
(OS) RAM  
Extended Memory  
RCONF_A0_BF-RCONF_E0_FF  
RCONF_DEFAULT SYSRC  
System and Option ROMs  
Conventional Memory  
SMM and DMM header and  
table walk properties  
RCONF_BYPASS  
RCONF-RCONF7  
Not Used  
Figure 7-3. CPU Core Cache Region Configurations  
32  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
 
Memory Map  
32430C  
Reset  
ROM  
Fetch  
N
CPU ID  
Correct?  
Uses CPU ID instruction.  
Halt  
Y
CMOS/NVRAM  
Valid and  
Checksum  
Ok?  
N
Y
Y
Failed to  
Boot  
Failed boots need a POR  
reset and will always take this path.  
Load CMOS/  
NVRAM Defaults  
3 Times?  
N
Early CS5535  
Initialization  
PLL Flag  
indicates  
2nd Pass?  
Y
N
Continue POST  
PLL Reset completed  
Jumper settings correspond  
to a table of SKUs for each  
revision of the CPU.  
Get Core and GLIU  
Settings from Jumper  
Settings or CMOS  
PLL settings can be set  
manually for debug.  
Set All Clocks  
GLCP_SYS_RSTPPL  
(MSR Addr. 4C00014h)  
CPU Speed to get  
PCI Clock  
Set PLL Flag  
DRAM Clock Setting  
from SPD  
Internal PLL Reset  
Figure 7-4. GeodeROM Flow - GX Processor/CS5535 Device  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
33  
   
32430C  
Memory Map  
Finish Post  
Enable  
Interrupts  
Setup Stack  
VSA  
Initialization  
Shadow ROM  
Initialize and  
Enable Cache  
System ROM  
Initialization  
Northbridge  
Initialization and  
CPU Bug Fixes  
PCI and Video  
Option ROM  
Initialization  
CS5535 descriptor  
set here,  
Chipset  
Initialization  
N
Keyboard  
after shadow.  
Flag  
Reset Reboot  
F1 Pressed?  
Y
SuperI/O  
Initialization  
INT 19  
Setup  
Flag  
Reset Reboot  
Reset  
34  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
Appendix A: Support Documentation  
32430C  
Appendix ASupport Documentation  
A
A.1  
Document Revision History  
This section reports the revision/creation process of the porting guide. Any revisions (i.e., additions, deletions, parameter  
corrections, etc.) are recorded in the table(s) below.  
Table A-1. Revision History  
Revision #  
(PDF Date)  
Revisions / Comments  
A (30-Jun-2005)  
Initial release.  
B (22-Mar-2006) The goal was to remove “Confidential” to make this an non-NDA document. Also incorporated other  
minor corrections. See revision B for details.  
C (25-Apr-2006)  
Section 4.0 "Initialization" on page 15: Several sub-sections had incorrect MSR Addresses. Most  
were 7 digits long instead of 8 (missing a 0). Corrected these.  
Section 4.2.4.8 "Flash Interface" on page 22: Changed 5535.ASM to CHIPSET.ASM.  
AMD Geode™ GX Processor/CS5535 Companion Device GeodeROM Porting Guide  
35  
   
One AMD Place • P.O. Box 3453 • Sunnyvale, CA 94088-3453 USA • Tel: 408-749-4000 or 800-538-8450 • TWX: 910-339-9280 • TELEX: 34-6306  

Hobart HGC20, HGC20, ML 114573, ML 114575 User Manual
GE DECT 28132 User Manual
Fisher Paykel CT5602F User Manual
Electrolux 880059 User Manual
Cypress CY14B101L User Manual
AT T 9311 User Manual
Asus Computer Hardware GRYPHONZ87 User Manual
Asus 820E User Manual
AOC 9GLR User Manual
Antec NSK 4000 II User Manual