operator's manual
INCLUDES SERVICE INFORMATION
MODEL 8000 & 8100
CHIPPER
PN-51210 (Rev. 7/98)
C
O N T E N T S
Contents
SafetyInstructions.............................................................. 2
SafetyDecals ............................................................................. 6
Assembly........................................................................... 7
AttachChipperChute ................................................................... 7
AttachChuteExtensionTray ......................................................... 8
AttachBlowerDischargeTube ....................................................... 8
ConnecttheHydrostaticControlCable ............................................. 9
ConnectPTOShaft ...................................................................... 9
Controls........................................................................... 10
Operation ......................................................................... 11
Starting.....................................................................................11
Chipping....................................................................................12
Stopping ...................................................................................12
ServiceandMaintenanceSchedule .................................... 13
ServiceandMaintenance................................................... 14
SharpeningChipperBlades ...........................................................14
SettingChippingBladeClearance .................................................. 15
AdjustingorReplacingtheDriveBelts ............................................ 16
ClearingPluggedRotor ................................................................16
RepairingorReplacingRotorBearings ............................................ 17
GreaseableBearings ...................................................................18
HydraulicFeed ................................................................. 19
InstallingtheOptionalHydraulicFeedKit ........................................19
HydraulicFeedInstructions ..........................................................22
ControlArmOperation .................................................................23
HydraulicSchematic ...................................................................23
HydraulicFeedMaintenance ......................................................... 24
HydrostaticPumpTroubleshooting .................................................24
Troubleshooting ............................................................... 25
AssemblyDiagramsandPartsLists ................................... 26
ServiceAccessories ...................................................................26
ChuteandRotorAssemblyPartsList ............................................. 26
ChuteandRotorAssemblyDiagram ...............................................27
ChipperBaseAssemblyDiagram ................................................... 28
ChipperBasePartsList ............................................................... 28
Hyd.FeedAssy.DiagramandParts.................................... 30
HydraulicFeedAssemblyDiagram .................................................30
HydraulicFeedPartsList .............................................................32
Specifications .................................................................. 33
Warranty
PN-51210 (Rev. 7/98)
S
A F E T Y
I
N S T R U C T I O N S
SafetyInstructions
Thischipperisdesignedandtestedtoofferreasonablysafeservice.
Failuretooperateitinaccordancewiththefollowingsafety
instructions MAY RESULT IN PERSONAL INJURY!
A safety message alerts you to potential hazards that could hurt you or others.
Each safety message is proceeded by one of three words: DANGER,
WARNING, or CAUTION.
You WILL be KILLED or
SERIOUSLY HURT if you don't
follow instructions
DANGER
You CAN be KILLED or
WARNING
CAUTION
SERIOUSLY HURT if you don't
follow instructions.
You CAN be HURT or DAMAGE
machine if you don't follow
instructions.
BeforeOperating
•
Read the owners manual before operating this equipment.
•
•
•
Do not allow children to operate this equipment.
Do not operate this equipment in the vicinity of bystanders.
Do not allow hands—or any part of body or clothing— inside the
feeding chamber, discharge chute, or near any moving part.
•
Shut off the power source and make sure all moving parts are com-
pletely stopped before inspecting or servicing any part of the machine.
Preparation
•
•
Wear safety glasses at all times while operating the machine. One pair is
provided with each chipper.
Avoid wearing loose-fitting clothing. Never operate this machine
wearing loose clothing particularly if it has drawstrings which can wrap
around or get caught in the machine.
•
•
Operate the machine only on a level surface.
Do not operate the machine on a paved, concrete, or hard gravel surface.
Operating on a hard surface causes discharged material to rebound and
kickback. It will also cause increased machine vibration. Increased
vibration causes the machine to move and will promote premature wear
of parts or loosening of fasteners.
PN-51210 (Rev. 7/98)
2
S
A F E T Y
I
N S T R U C T I O N S
•
Visually check that all screws, nuts, bolts, and other fasteners are properly
secured before starting the machine. Check all screws, nuts, bolts, and other
fasteners once every 10 hours of operation for proper tightness to insure
everything is in proper working condition.
Operation
•
•
Empty the cutting chamber before starting the machine.
Exclude pieces of metal, rocks, bottles, cans, and other foreign objects
when feeding chipable material into the machine.
•
Shut off the engine or PTO and allow the machine to stop if the cutting
mechanism strikes any foreign object or if the machine starts making an
unusual noise or vibration. After machine stops:
a) Inspect for damage.
b) Replace or repair any damaged parts.
c) Check for and tighten any loose parts.
•
•
Do not allow processed material to build up in the discharge area; this may
prevent proper discharge and result in kickback of material through the feed
opening.
Do not allow hands or any other part of the body or clothing inside the
feeding chambers, discharge chute, or near any moving part.
•
•
•
•
•
•
Keep all guards and deflectors in place and in good working condition.
Stand clear of the discharge area when operating this machine.
Keep your face and body back from the feed opening.
Do not over reach. Keep proper balance and footing at all times.
Do not transport or move machine while the machine is running.
Disengage PTO and shut off tractor engine if the machine becomes clogged.
Allow machine to come to a complete stop before clearing debris.
WARNING: Keep body and clothing away from PTO shaft when running.
•
•
Connect 3 pt. hitch pins and snap pins, connect PTO shaft, and have leg
stands solidly on the ground when in use.
Lock the rotor by inserting a bolt or punch through the locking holes on the
side of the rotor housing before moving. To move unit: shut off PTO and lift
3 pt. hitch.
•
Keep guards and shields in place at all times while operating. Disengage
tractor PTO and shut off engine before removing guards or shields.
•
•
Keep hands, feet, and clothing away from all PTO drive parts.
Never clean, lubricate, or adjust the chipper when it is running.
PN-51210 (Rev. 7/98)
3
S
A F E T Y
I
N S T R U C T I O N S
•
Put transmission in neutral or park and disengage before starting tractor.
WARNING: This chipper is designed to be used with tractor PTO's rated at
20 to 60 horsepower. Using this chipper with PTO's above 60 horsepower
may cause belt and machine damage in overload conditions.
AdditionalSafetyRulesforPTOModels
•
•
•
Stay alert and pay attention when PTO chipper is operating.
Keep bystanders, especially children, away from the PTO driveline.
Connect 3 pt. hitch pins and snap pins, connect PTO shaft and have leg
stands down and secure when in use.
•
•
Check the driveline to ensure it is attached securely to the tractor.
Keep guards and shields in place at all times while operating. Disengage
tractor PTO and shut off engine before removing guards or shields.
•
Keep hands, feet, and clothing away from all PTO drive parts.
•
•
Do not clean, lubricate, or adjust the PTO when it is running.
Clothing worn by operator must be fairly tight. Never wear loose
jackets, shirts, shirt sleeves or pants when working around PTO. Tie
long hair back or put under a cap.
PN-51210 (Rev. 7/98)
4
S
A F E T Y
I
N S T R U C T I O N S
•
•
Keep hydraulic hoses, electric cords, chains, and other items from
contacting the driveline.
Make sure transmission is in neutral or park and PTO is disengaged
before starting the tractor.
•
•
Do not exceed the recommended 540 RPM PTO operating speed.
Disconnect PTO and shut off tractor when this unit is stopped for
servicing, inspection, storage, or to change an accessory.
•
•
Shut off the PTO, lift 3 pt. hitch, and adjust leg stands if needed to move
the unit.
Read and follow instructions on PTO safety decals.
WARNING!RecommendedtractorPTOhorsepoweris15HPto30HP.Useoftheseunitson
tractorsabove30PTOhorsepowermaycausebeltandmachinedamageinoverloadconditions.
SafeStorage
•
•
Disengage PTO when this equipment is stopped for servicing,
inspection, storage, or to change an accessory.
Store the machine out of reach of children. Clear debris from inside the
machine and store in a dry area for storage periods of three months or
more.
PN-51210 (Rev. 7/98)
5
S
A F E T Y
D
E C A L S
SafetyDecals
Safetyandinstructiondecalsarelocatedonthechipperframeandengine.
Replaceanydamagedorunreadabledecal.
NOTE: See parts drawings and lists for location of safety decals on the
chipperframe.
PN 57835, French Safety Decal Kit
PN51284
PN51361
PN51281
PN51373
PN51375
PN51312
PN-51210 (Rev. 7/98)
6
A
S S E M B L Y
Assembly
For instructions on assembling the hydraulic feed kit, see page 20.
AttachChipperChute
Do not operate this unit without the chipper chute correctly installed. Rotating
cutting blades can cause serious personal injury.
1. Remove chipper from shipping crate. Place unit on a level surface before
attempting to assemble. See torque chart for minimum tightening torque.
2. Mount the chipper chute to the frame mounting bracket using eight 3/8" x 1"
bolts and locknuts. Use three bolts on each side and two on the bottom (see
figure 1). Attach the chute directly to the hydraulic feed unit as described
above for models with factory-installed hydraulic feed.
TorqueChart
Standardminimum
tighteningtorquefor
normalassembly
applications.
Bolts (SAE GR5)
Size
5/16"
3/8"
Ft.Lbs.
20
35
1/2"
75
Screws
Size
Ft.Lbs.
5/16"Set
15
Chipper
Chute
Figure1
PN-51210 (Rev. 7/98)
7
A
S S E M B L Y
AttachChuteExtensionTray
1. Slide the chute extension tray over the chipper chute as shown in figure
2 after mounting the chute to the chipper frame. Make sure you position
the lip on the extension tray behind the lip on the chipper chute. Align
the five bolt holes in the chute extension tray with the bolt holes in the
hinge.
2. Insert five 3/8" x 1" carriage bolts (included in owners kit packaged with
the chipper) through the tray and the extension hinge. Secure the bolts
with washers and nuts. Secure with hairpin clips.
AttachBlowerDischargeTube
1. Attach the blower discharge tube to the mounting flange on the chipper
frame (see figure 3). Half of the mounting clamp is already attached to
the tube. Slide the tube into the flange and tighten the bolts to secure it.
Install the second half of the clamp to the tube and flange. Rotate the
ock it in place with the handle to make sure it is
Hairpin
Clip
Positionthislip
behindthelipon
thechipperchute
Blower
shownbelow.
Discharge
Holdtheextension
Tube
traydirectlyabove
thechipperchute
andslideit
ExtensionTray
downward.
FeedControl
Lever(Models
withhydraulic
feedonly.)
s
Chipper
Chute
Extension
Hinge
Figure2
Figure3
PN-51210 (Rev. 7/98)
8
A S S E M B L Y
ConnecttheHydrostaticControlCable
(Formodelswithfactoryinstalledhydraulicfeed.)
1. Remove the clevis assembly from the hydrostatic control cable end (see
figure 4). Remove one nut on the cable end. Insert the cable end into the
hole in the cable anchor weldment. Replace the nut and the clevis assembly.
2. Attach the clevis assembly to the center hole on the feed control lever.
3. Adjust the cable detent ball to contact the detents in the cable anchor
weldment when the control arm is in the forward position or reverse position.
Important! See hydrostatic pump start-up procedure.
ConnectPTOShaft
1. Connect the PTO shaft female end to the rotor shaft using key stock and two
set screws contained in the owner's kit.
2. Connect the opposite end of the PTO shaft to the tractor.
3. Check all screws, bolts, and nuts for tightness. See torque chart, page 5 for
minimum tightening torque.
Clevis
Assembly
Detent
Ball
Insertcable
throughhole
Nut
FeedControl
Lever
CableAnchor
Weldment
Hydrostat
ControlCable
Figure4
PN-51210 (Rev. 7/98)
9
C O N T R O L S
Controls(seefigure5)
1. Three pt. Hitch Connection: Mounts chipper to tractor 3 pt. hitch.
Connect direct for category 1.
2. PTO Shaft: Connects chipper to tractor PTO shaft. Avoid driveline
angles over 20 degrees on PTO shaft when unit is in use.
3. Drive Belt Shield: Never remove shield while machine is running.
4. Chipper Chute: Feeds materials to the chipper blades for chipping.
5. Leg Stands: Never move machine unless legs are in UP position and
clear the ground.
6. Rotor Access Cover: Tilts up to remove chipper blades and to service
rotor assembly.
7. Discharge Tube: Chipped materials will exit through this tube. Tube is
adjustable 360 degrees.
8. Adjustable Chipping Anvil: Adjusts to vary the size of chips.
9. Rotor Shaft Bearing Cover: Rotor shaft has lock assembly to lock rotor
in place while moving.
PTOModel
Controls
Figure5
7
6
4
9
8
3
2
1
5
PN-51210 (Rev. 7/98)
10
O
P E R A T I O N
Operation
CAUTION: Wear safety glasses at all times when operating the
machine. Do not wear loose fitting clothing. The operator should always
wear heavy boots, gloves, pants, and shirt. Use common sense and practice
safety to protect yourself from branches, sharp objects, and other harmful
objects.
NOTE: The heavy rotor continues to turn for some time after the tractor
has been shut off. The rotor is stopped when no noise or machine vibration
is present. Inserting a branch into the chipper chute to contact the blades
slows the rotor and shortens stopping time.
NOTE: Minimum and maximum telescoping on the PTO shaft is 20-28
inches. This will leave 4 inches overlap at maximum telescoping distance
(see figure 6).
Starting
1. Place tractor transmission in park or neutral and set parking brake.
Connect 3 pt. mounts between the chipper and tractor. Secure connec-
tions with snap pins. Adjust 3 pt. top link so chipper sits level.
2. Connect PTO shaft to tractor. Make sure you are using the correct RPM
machine. Do not operate machine at speeds different than specified on
shield.
3. Do not inspect or work on PTO drive area without first disengaging PTO
and shutting off tractor engine.
4. Start tractor engine and engage PTO drive clutch (see tractor owner's
manual). Increase engine speed to rated PTO RPM position.
WARNING:This
chipperisdesigned
tobeusedwith
tractorPTO'srated
at20to60
horsepower. Using
thischipperwith
PTO'sabove60
horsepowermay
causebeltand
Figure 6
Telescoping Type
20 to 28 inches will leave
at least 4 inches overlap
machinedamagein
overloadconditions.
PN-51210 (Rev. 7/98)
11
O
P E R A T I O N
Chipping
WARNING: Keep face and body away from the feed opening. Do not
over reach. Keep proper balance and footing at all times.
The Woods chipper is designed to chip a variety of materials into a more
readily decomposing or handled condition. The following guidelines can be
used to help you get started. Please read and follow all safety instructions in
this manual. Failure to operate the chipper in accordance with the safety
instructions MAY RESULT IN PERSONAL INJURY!
•
•
Be sure the unit is at full operating speed before starting to chip material.
Select limbs up to 8 inches in diameter. Trim side branches that cannot
be bent enough to feed into the chipper chute. Hold small diameter
branches in a bundle and feed simultaneously.
•
•
•
Feed brush from the side of the infeed chute rather than from the front.
Step aside to avoid being hit by brush moving into the chipper.
Never lean into the infeed chute to push objects into the cutting device. Use
a push stick or brush paddle.
Do not use shovels or forks to push brush. They can go through the chipper,
are expensive to replace, and cause major damage. Metal pieces can come
back like shrapnel to injure or kill.
•
•
Never push brush into the infeed chute with your feet.
Place limb, butt end first, into the chipper chute until it contacts the
chipper blades. The actual feed rate of the limb into the chipper will
depend on the type of material fed and sharpness of the cutting blades.
•
Alternately insert and retract the limb or insertcontinuouslyataratethat
will not stall the tractor. Rotating the branch as you feed it will improve
cuttingaction.
NOTE: The chipping blades dull with use and require periodic sharpening.
Refer to service and maintenance, "sharpening chipper blades" for
instructions.
Stopping
WARNING: Do not leave machine unattended, or attempt any inspection or
service unless PTO is disengaged and tractor engine is shut off. Allow
machine to come to a complete stop. To stop machine, proceed as follows:
1. Move tractor throttle to SLOW position.
2. Disengage PTO lever and shut off tractor engine.
3. Allow machine to come to a complete stop.
NOTE: The heavy rotor continues to turn for some time after the engine or
tractor has been shut off. The rotor is stopped when no noise or machine
vibration is present. Inserting a branch into the chipper chute to contact the
blades slows the rotor and shortens stopping time.
PN-51210 (Rev. 7/98)
12
S
E R V I C E A N D
M
A I N T E N A N C E
S
C H E D U L E
ServiceandMaintenanceSchedule
Interval
Every
100
Before
Each
Use
Every
10
Hours
Every
25
Hours
Every
50
Hours
Every
200
Hours
Every
300
Hours
Every
800
Hours
Every
1
years
InspectionItems
Check Nuts & Bolts (Entire machine)
Check
Hours
Replace
Check
*
Clean
Hydraulic Filter Element
Replace
Check Hydraulic Control Cable
Check Sharpness of Chipper Blades
Grease Bearings and Pivots
Check Bolts: Chipper Blade, Chipper
Anvil, Rotor Paddles
Check Drive Belt
Clean Machine
Note: (*) Service more frequently when used in dusty conditions
Beforeinspectingorrepairinganypartofthemachine,shutofftheengineandmakesureall
movingpartshavecometoacompletestop.
Indicates first hours of use.
PN-51210 (Rev. 7/98)
13
S
E R V I C E A N D
M
A I N T E N A N C E
ServiceandMaintenance
WARNING: Shut offPTO and make sure all moving parts have come
toacompletestopbeforeinspectingorservicinganypartofthemachine.
Thechippingbladesaresharp!Usecarewhenworkingonmachinetoavoid
injury.
WARNING: The rotor assembly has a lock mechanism. Use the lock
mechanism at all times when working on the rotor assembly. Remove plastic
bearing cover under chipper chute. There is a hole in the rotor jack shaft and
a matching hole in the bracket mounted to the rotor bearing front side.
Install a punch through the rotor shaft and bracket to lock the rotor in place.
SharpeningChipperBlades
The chipper blades dull, making chipping difficult. It is recommended to
sharpen the chipper blades every 5-15 hours of chipper operation. To
remove the chipping blades for sharpening:
1. Remove the two 3/8" retaining bolts holding access cover to main frame
assembly.
2. Tilt access cover over to allow rotor access. Rotate the rotor so the bolts
holding a chipping blade are most accessible.
3. Remove the two allen head bolts holding the blade itself. Repeat for all
four blades. The four chipping blades have two edges per blade and can
be reversed one time each before sharpening. Remove and reverse the
chipping blades if both sides have not been used. Reinstall chipping
blades and proceed with chipping.
To grind the angled edge of the chipping blade to 45 degrees (see figure 7):
Grind the blades on a slow-speed wet grinder, if possible, or have them
Sharpening
Edges
45⋅
t
s
t
t
Figure7
0.38
Figure8
PN-51210 (Rev. 7/98)
14
S
E R V I C E
A N D
M
A I N T E N A N C E
sharpened by a professional. Be careful when grinding if using a bench
grinder so the blade material does not get too hot and change color–this will
remove the blade's special heat treated properties. Use short grinding times
and cool with water. Remove an equal amount off each blade to maintain
balance. Replace the chipping blades and tighten bolts to 75 ft. lbs. Close
cover and replace bolts.
Youdonothaveto
removetherotorfromthe
mainframetorepairthe
chipperbladesorpaddles
locatedonthebackofthe
rotorassembly.
ChippingBladeSharpeningTips
Poor chipping performance is usually a result of dull chipping blades. Check
for the following symptoms if chipper performance has decreased:
•
•
•
Severe vibration when feeding material into the chipper.
Small diameter branches do not self-feed.
Chips discharge unevenly or have stringy tails–especially when chipping
green branches.
Check for permanent damage before you sharpen the chipping blades.
Replace the blade if:
•
•
The blade is cracked (especially around the bolt holes) or the edges are
too deeply chipped to be ground smooth.
The base of the cutting edge is worn or has been re-sharpened so it is too
close to the rotor chipping slot.
SettingChippingBladeClearance
Thefour-edgedchippinganvillocateddirectlyunderthechipperchute
shouldclearthechippingbladeby1/16inchto3/16inch. Thechipping
anvilisadjustableandreversible.
ToAdjust:
1. Lift rotor access cover and expose rotor (see figure 8, page 12). Loosen
the three 1/2" bolts holding the chipper anvil to the frame.
2. Measure the amount of clearance between chipping blade and chipping
anvil from inside of housing.
3. Adjust inward or outward to desired measurement.
4. Tighten bolts on chipping anvil to 75 ft. lbs. and resume operation.
Removethethreeboltsholdingtheanvilanduseoneoftheotherthree
edges if the chipping anvil edge is damaged or worn unevenly. Adjust for
correctmeasurement.
PN-51210 (Rev. 7/98)
15
S
E R V I C E A N D
M
A I N T E N A N C E
AdjustingorReplacingDriveBelts
Checktheconditionofthedrivebeltsannuallyorafterevery30hoursof
operating,whichevercomesfirst.Replacecracked,frayed,orwornbelts.
Proceedasfollowstoreplaceoradjustthedrivebelt:
1. Disengage PTO and shut off tractor engine.
2. Remove PTO shaft from tractor; disconnect machine from 3 pt. hitch.
3. Remove round shield connected to belt guard covering the PTO shaft by
removing two 5/16" nuts.
4. Remove PTO shaft from chipper by removing two set screws and pulling
shaft off.
5. Remove belt guard covering pulleys and belts.
6. Lift spring loaded idler pulley off of belt and remove belt.
7. Install new belt and reverse above instructions to complete belt
replacement.
ClearingPluggedRotor
WARNING: Shut off the tractor engine and allow the machine to
completely stop before clearing debris if the machine plugs. Do not operate
the machine without proper guards and screens in place.
The chipper can plug if too large or too much material is fed into it. Proceed
as follows to clear plugged rotor:
1. Disengage PTO and shut off tractor engine.
2. Lift rotor access cover.
3. Clean the debris out of the chipping rotor. Turn the rotor by hand to be
sure it is free to rotate.
4. Replace rotor access cover.
5. Start tractor, engage PTO, and resume operation.
PN-51210 (Rev. 7/98)
16
S
E R V I C E
A N D
M
A I N T E N A N C E
RepairingorReplacingRotorBearings
1. Remove two 3/8" retaining bolts holding access cover to main frame
assembly. Tilt access cover over to allow rotor access.
2. Remove large belt guard (three 5/16" bolts).
3. Loosen bolts on hydraulic pump and remove hydraulic pump belt.
Remove the bushing and pulley from the rotor shaft using the push bolts
from the bushing.
4. Lift belt idler pulley off drive belt and remove belt from pulleys. Remove
the bushing and pulley from the rotor shaft using the push bolts from the
bushing.
WARNING: The rotor assembly has a lock mechanism. Use the lock
mechanism at all times when working on the rotor assembly. Remove plastic
bearing cover under the chipper chute. There is a hole in the rotor jack shaft
and a matching hole in the bracket mounted to the rotor bearing front side.
Install a punch through the rotor shaft and bracket to lock the rotor in place.
5. Remove four 1/2" bolts on each rotor bearing and remove punch used to
lock the rotor.
6. Lift the rotor assembly completely out of the frame using an overhead
hoist or lifting device. The complete rotor assembly weighs 275 lbs.
7. Remove 3/8" bolts and collar from front once the rotor assembly is out
of the frame. Remove both bearings with a puller and place new
bearings on rotor shaft. Replace collar.
8. Return the complete rotor assembly to the chipper frame with an
overhead hoist or lifting device.
9. Slide rotor back until front collar is tight against the front bearing. Lock
the front bearing and install four 1/2" bolts on each bearing to secure
them to the frame. Tighten bolts to 75 ft. lbs. Check and adjust chipper
anvil if needed. Lock rear bearing.
10. Slide rear collar on shaft against rear bearing. Slide bushing onto shaft
with flange against collar and lock bushing to shaft. Attach large pulley
to bushing. Replace drive belt on pulleys and lower belt idler. Check
alignment of pulleys and adjust engine if needed.
11. Close cover and replace bolts.
12. Replace hydraulic pump bushing and pulley. Replace hydraulic pump
belt. Readjust hydraulic pump belt tension by sliding the hydraulic pump
in the mounting slots. Tighten bolts.
13. Replace belt guard and resume operation.
14. Start tractor engine and engage PTO drive clutch (see tractor owner's
manual). Increase engine speed to rated PTO RPM Position. Test unit,
readjust pulleys, and belt tension if needed.
PN-51210 (Rev. 7/98)
17
S
E R V I C E
A N D
M
A I N T E N A N C E
Important!
Check the bolts on the following for correct torque (75 ft. lbs.) every
10 hours of operation:
• Hydraulic feed roller bearing
• Hydraulic motor mounting
• Chipper rotor bearing
• Chipper blades
• Rotor paddles
• Chipper anvil
Warning: Failure to maintain proper fastening torque (75 ft. lbs.) on bolts
for the components listed above may result in severe damage to the chipper
and/or personal injury!
GreaseableBearings
The PTO model has ten grease zerks. Minimal periodic greasing is needed
on these points every 50 hours:
•
•
•
•
•
Four grease zerks on the PTO shaft itself.
Two greaseable bearings on the rotor shaft.
Two greaseable bearings on the bottom jack shaft.
One idler arm pivot
One discharge chute
PN-51210 (Rev. 7/98)
18
H
Y D R A U L I C
F
E E D
I
N S T A L L A T I O N
HydraulicFeed
InstallingtheOptionalHydraulicFeedKit(Formodelswithoutfactory
installedhydraulicfeed.)
InstalltheRollerAssembly
1. Remove the bolts fastening the chipper chute to the rotor housing weldment.
2. Remove the chipper chute mounting plate.
3. Hold the roller assembly up to the rotor housing weldment. Secure the roller
assembly with 3/8" x 1-1/2" bolts, washers, and nuts.
4. Attach the chipper chute to the roller assembly with 3/8" x 1-1/2" bolts,
washers, and nuts.
AttachtheControlArm
1. Remove the canvas chipper chute flap and angle.
2. Fasten the cable anchor to the chipper chute with 3/8" x 1-1/4" bolts,
washers, and nuts.
3. Attach control pivot and extension hinge to the chipper chute bottom with
3/8" x 1-1/2" bolts, washers, and nuts.
4. Put three 5/8" washers on both control pivot shafts.
5. Place the control arm shaft holes over the control pivot shafts.
6. Place a 5/8" bearing over each pivot shaft and fasten each bearing to the
control arm with two 3/8" x 1" bolts and nuts.
7. Attach the feed control lever to the cable anchor weldment by inserting a
5/16" x 2" bolt through the bolt holes. Place the drift cutter spring over the
end of the bolt. Secure the bolt and spring with a 5/16" washer and nut.
8. Put the detent ball into the detent cavity on the feed control lever. Insert the
detent spring into the detent cavity. Secure the spring and the ball by
threading a 3/8" x 1" bolt through a 3/8" nut and then threading the bolt into
the detent cavity.
9. Connect the control arm to the feed control lever with the control tie rod
strip. Place a 5/16" washer and an idler pivot spacer over a 5/16" bolt. Insert
the bolt through the bolt hole in one end of the control tie rod strip and the
top bolt hole on the feed control lever. Secure the bolt with a 5/16" washer
and nut. Insert a 5/16" x 1" bolt (with a 5/16" washer and idler pivot spacer)
through the other bolt hole in the control tie rod strip and the control arm.
Secure with a 5/16" washer and nut.
PN-51210 (Rev. 7/98)
19
H
Y D R A U L I C
F
E E D
I
N S T A L L A T I O N
Installthe6.6"Pulley
1. Remove the chipper drive belt guard.
2. Put the 6.6" pulley on the rotor shaft end.
3. Place the 1.75" bushing on the rotor shaft and put the 3/8" x 1/4" key into
the bushing slot. Do not tighten the bushing yet.
MounttheHydrostaticPump
1. Attach the pump control arm to the pump control on the hydrostatic pump
with two 1/4" x 1/2" bolts.
2. Mount the pump mount bracket to the hitch weldment by inserting two 3/8"
x 1-1/2" bolts through the bolt holes. Place the cable attachment angle over
the bolt ends on the other side of the hitch weldment. Secure the bolts with
two 3/8" washers and nuts.
3. Slide the 4" pulley over the pump shaft. Slide the 15mm bushing next to the
pulley. Place the 5mm x 25mm key into the bushing. Do not tighten the
bushing yet.
ConnecttheHydrostaticCable
1. Insert the hydrostatic control cable end (the end without nuts attached)
through the cable hole in the hitch weldment.
Figure9
Roller
Assembly
Hydrostatic
Motor
Crossover
ReliefValve
PN-51210 (Rev. 7/98)
20
H
Y D R A U L I C
F
E E D
I
N S T A L L A T I O N
2. Thread the cable end into the cable pivot pin. Insert the pivot pin into the
hole in the pump control arm. Secure the pivot pin with a 1/4" washer
and a 3/32" x 3/4" cotter pin.
3. Place the cable clamp shim and clamp on the cable exterior (as shown
on page 20). Secure the cable, clamp, and shim to the cable attachment
angle with two 1/4" x 3/4" bolts and locknuts.
4. Remove one nut on the opposite cable end. Insert the cable end into the
hole in the cable anchor weldment. Replace the nut.
5. Attach the clevis assembly to the center hole on the feed control lever.
AttachtheValveandMounttheReservoir
1. Attach the crossover relief valve to the chipper stand with two 3/8" x 2"
bolts, washers, and nuts.
2. Attach the reservoir support weldment to the chipper rotor housing with
two 5/16" x 3/4" bolts, washers, and nuts.
3. Put the tank on the reservoir support.
4. Place the reservoir straps over the tank and secure with 5/16" x 3/4"
bolts, washers, and locknuts.
ConnecttheBelt
1. Attach the belt to the 6.6" rotor shaft pulley and the 4" hydrostatic pump
pulley.
2. Align the two pulleys with a straight edge.
3. Tighten both pulley bushings.
4. Move pump to tighten belt.
5. Install the hydraulic hoses as shown on page 20. Follow hydrostatic
pump start up and maintenance instructions on pages 20 and 21.
6. Replace chipper drive belt guard.
7. Install chute extension tray as described on page 6.
PN-51210 (Rev. 7/98)
21
H
Y D R A U L I C
F
E E D
O
P E R A T I O N
I
N S T R U C T I O N S
HydraulicFeedOperatingInstructions
Fluids
Handle pressurized hydraulic fluid carefully. Escaping pressurized hydraulic
fluid has sufficient force to penetrate skin causing serious injury. This fluid
may also be hot enough to burn. Serious infection or reactions can develop
if proper medical treatment is not administered immediately.
Premium hydraulic fluids containing high quality rust, oxidation, and foam
inhibitors are required. These include premium turbine oils, API CD engine
oils per SAE J183, M2C33F or G automatic transmission fluids meeting
Allison C-3 or Caterpillar TO-2, and certain specialty agricultural tractor
fluids.
HydrostaticPumpStartUpProcedure
Follow this start-up procedure to start a new installation or to restart an
installation if the hydrostatic pump was removed from the system.
Hydrostaticpressure
controlledbythe
1. Make sure all system components (reservoir, fittings, etc.) are clean
before starting the hydrostatic pump.
crossoverreliefvalveis
factorysetat1750PSI.
A2000PSIshimkitis
availableforextreme
conditions.
2. Fill the reservoir with recommended hydraulic fluid (filter before filling).
3. Fill the inlet line leading from the reservoir to the charge pump before
start-up. Loosen the fitting on this inlet line until oil bleeds out.
Warning! Do not start engine unless pump is in neutral or detent position on the
cable.
4. Start the engine and run at the lowest possible RPM.
5. Refill the reservoir as necessary. The oil level in the reservoir drops and
bubbles appear in the fluid as air purges from the unit.
6. Run the unit in both directions for several minutes until any remaining
air is purged from the unit. Refill the reservoir as necessary.
7. Loosen a motor fitting and oil-bled to remove air from the system (use
same procedures as steps 3-5) if needed.
8. Disengage PTO, check for and correct any fluid leaks, and check the
reservoir level. Add fluid if necessary.
•
The hydrostatic pump is now ready for operation.
Input Shaft Seal
ChargePump
Figure10
ChargeCheckValve
Control Shaft Seal
BypassValve
Pump-Component
Locations
PN-51210 (Rev. 7/98)
22
H
Y D R A U L I C
F
E E D
O
P E R A T I O N
I
N S T R U C T I O N S
ControlArmOperation
1. Engage the PTO. Bring the chipper up to operating speed. See the
operationsectionforstarting, operation, andstoppinginstructions.
Pleasereadand
followallsafety
2. Engage the hydraulic feed by moving the control arm as shown in figure
11 below. The feed rate increases as the arm is moved in the forward
direction.
instructions in this
manual.Failureto
operatethechipperin
accordancewiththe
safetyinstructions
MAYRESULTIN
3. Feed the branch (up to eight inches in diameter).
4. Reverse the feed by moving the control arm in the reverse direction if the
chipperjams. Removethebranchandrotateitbeforereinsertingitintothe
chute.
PERSONALINJURY!
Neutral
Reverse
Forward
FeedControl
Lever
Figure11
HydraulicSchematic
Partslistedonpage28.
PN-51210 (Rev. 7/98)
23
H
Y D R A U L I C
F
E E D
M
A I N T E N A N C E
HydraulicFeedMaintenance
NOTE:Checkthereservoirdailyforproperfluidlevel,thepresenceof
water(notedbyacloudytomilkyappearanceorfreewaterinbottomof
reservoir),andrancidfluidodor(excessiveheat).
The hydrostatic pump normally does not require regular fluid changes.
Change the system filter at 250 hour or annual intervals. Change the fluid
and filter and clean the system if the fluid becomes contaminated with
foreign matter (water, dirt, grease, etc.) or if the fluid has been subjected to
temperature levels greater than the recommended maximum.
There is a greaseable bearing on each side of the main jack shaft on the
main hydraulic feed housing. Grease periodically.
HydrostaticPumpTroubleshooting
ProbableCause
SuggestedRemedy
Symptom
Contactyourdealeror
factoryservice
Willnotattainnormalfeedrate.
Enginenotoperatingat
correct speed.
Repairenginegovernor.
Repair control linkage.
Repair bypass valve.
Control linkage damaged or
binding.
departmentBefore
servicingorrepairing
anyofthehydrostatic
feedcomponents(pump,
motor,and/orrelief
valve).Warrantyon
theseitemsmaybevoid
withoutprior
Bypass valve stuck partially
open. (Probleminone
direction only.)
Removeforeignmaterialfrom
valve.
Willnotfeedwhencontrolarm
ismoved.
Control linkage damaged or
notconnected.
Repair or reconnect control
linkage.
Drive between engine and
pumpdamaged.
Repair drive (replace broken
belt, repair sheared key, re-
pair splined coupling, etc.).
Refillreservoir. Purgeairfrom
transmission.
authorization.
Pumplowonfluid.
Feed rate is sluggish under
load.
Loosedrivebeltbetween
engineandpump.
Pumplowonfluid.
Tension drive belt (replace if
necessary).
Refillreservoir. Purgeairfrom
transmission if necessary.
Drainfluidfromreservoirand
unit, replace filter element,
and refill with new fluid.
Large amount of water in hy-
draulicfluid(evaporateswhen
hot, resultinginlowfluidlevel).
Hydraulic Feed will not pull in
logs over 4" in diameter, or
continuously stalls or stops.
Hydraulicsystemoverloading
and causing system to go
over relief
Check relief pressure in sys-
tem with a pressure gauge
ratedto2500psi. (Systemset
by factory at 1750 psi.)
PN-51210 (Rev. 7/98)
24
T
R O U B L E S H O O T I N G
Troubleshooting
Problem
Probable Cause
Suggested
Remedies
Reference
1. Rotordoesnotturn
a) Obstructed
discharge.
a) Usebranchor
similarobjectto
cleardischarge.
b) Clearrotor.
ServiceandMaintenance
b) Pluggedrotor.
2. Hardtofeedchipper
orexcessivepower
neededtochip
a) Obstructed
discharge.
a) Usebranchor
similarobjectto
cleardischarge.
ServiceandMaintenance
ServiceandMaintenance
b) Dullchipperblades.
c) Improperblade
clearance.
b) Sharpenblades.
c) Adjustclearance.
3. Chipperrequires
excessivepoweror
stalls
a) Obstructed
discharge.
a) Usebranchor
similarobjectto
cleardischarge.
b) Clearrotor,feed
materialinto
b) Pluggedrotor.
shreddermore
slowly.
c) Greenmaterialwill
notdischarge.
c) Alternatelyfeeddry
material,orallow
materialtodry.
4. Drivebelts
squealingor
smoking
a) Pluggedrotor.
b) Looseorwornbelts.
a) Clearrotor.
b) Adjustbelttension
orreplacebeltsif
needed.
ServiceandMaintenance
5. PTO will not turn or
hasslowRPM's
a) PTOshaftnot
engagedontractor.
b) PTOshaftloose.
a) EngagePTO.
ServiceandMaintenance
ServiceandMaintenance
b) Checkall
connectionsand
repairifneeded.
6. Vibrationwhile
running
a) Driveshaftvibration.
a) Checkdrivebelts
andpulleysforbad
orwornspots.
CheckPTOshaftfor
wear.
b) Rotoroutof
balance.
b) Inspectrotorfor
brokenormissing
chipperbladesand
paddles. Repairif
needed.
c) Checkrotortoseeif
itwobbles.
d) Checktoseeifrotor
isassembled
correctly.
PN-51210 (Rev. 7/98)
25
C
H U T E A N D
R
O T O R
A
S S E M B L Y
P
A R T S
L
I S T
ChuteandRotorAssemblyPartList
No. Part No.
Description
Qty. No.
27.
Part No.
51514
51311
51312
51310
51484
51489
3379
Description
Qty.
1
Grease Zerk 1/4" Drive Ball
Spring, LockCompression
Decal, Discharge
1. 51458
2. 51474
3. 51459
4. 51460
5. 51464
6. 51461
7. 51462
8. 51463
9. 51682
51982
Disk, Chipper
Collar, Chipper Lock
1
1
4
4
1
1
1
1
1
1
1
1
1
2
2
1
1*
1*
1
1
1
2
1
1
1
1
2
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
48.
49.
50.
51.
52.
53.
54.
55.
1
2
Blade, Chipper
Bearing, 1-3/4 4 Bolt Flange
Shaft, Chipper Top Pivot
1
Paddle, Big Chipper
1
Weldment, ChipperRotorShaft
Plate, ChipperBottom
Base, ChipperChute
Strip, Flap Retainer
1*
3
Bolt, 1/2 x 1-1/2" GR5 Hex Capscrew
SerialNumberDecal
N/A
1
BearingBracket, Right
Decal, Woods8000Chipper
Decal, Woods8100Chipper
51301
51261
3699
854
Cap, LargeShaft
1
THD Stud 1/2"-13 X 3" LG, B7, ZP
Bolt, 1/2 X 2" G5 Hex Capscrew, ZP
Washer, 1/2" Flat ZP (56PC/LB)
Nut, 1/2CenterLocknut
2
14
6
10. 51506 Assy, Top Housing (#23,29, 34, 55 Incl.)
11. 51507 Assy, Chipper Chute (#21 Included)
12. 51557 Assy, Chipper Discharge (#29 Included)
765
30
2
1093
58782
12169
2290
565
Nut, HexNutNC, ZP
13. 51467
14. 51468
15. 51469
16. 51472
17. 51473
18. 51470
19. 51471
20. 51554
21. 51373
22. 51374
23. 51375
24. 51361
25. 51284
26. 12650
Ring, DischargeSpacer
Ring, DischargeClamp
Lever, DischargeLock
Angle, FlapAnchor
Screw, 1/2 X 2" FLT HD SKT
Bolt, 3/8 X 1-1/4" HHCS GR5 ZP
Bolt, 3/8 X 2-1/2 GR5 Hex HHCS ZP
Washer, 3/8" FLT ZP-140PC/LB
Locknut, 3/8" NYL Insert, NE, ZP
Bolt, Carr 3/8" X 1-1/2" GR5 NC, ZP
Bolt, 5/16 X 2-1/2" G5 HX CAP ZP
Washer, 5/16" FLT ZP (195PC/#)
Locknut, 5/16NYL, NC, TYPNE, ZP
Bolt, 3/8" X 1" Carriage GR5 ZP
Cotter Pin, 1/8 X 1.00 ZP
8
12
1
24
25
10
1
Flap, Chipper Chute
Weldment, Dis. LockPin
Tube, Discharge Lock Pivot
Deflector, BlowerDischarge
Danger, Decal
28093
51239
1059
4378
71061
6697
3597
639
1
1
Decal, MadeinUSA
Decal, OperatingInstructions
DangerDecal
4
3
Bolt, 1/2 X 2-1/2" Hex HD
SpoutKnob, 5/16-18
6
Decal, AccessCover
Screw, #6 x 1/2" Drive
51270
58776
58775
2
Spacer, Anvil
1
Decal, CheckBolts
1
*Notusedonhydraulicfeedmodels
ServiceAccessories
Part#
Description
51222
Chipper blade kit for PTO and towable models.
Includesfourchipperbladesandreplacementboltsandnuts.
51315
57835
Set of three matched belts for PTO model
French Safety Decal Kit
PN-51210 (Rev. 7/98)
26
C
H U T E A N D
R
O T O R
A
S S E M B L Y
D
I A G R A M
ChuteandRotorAssemblyDiagram
PN-51210 (Rev. 7/98)
27
C
H I P P E R
Chippe
Chippe
No. Part No.
1. 51505
2. 51465
3. 51466
4. 51475
5. 51570
6. 51273
7. 81286
8. 51314
9. 51234
HitchSupportWeldment
Spacer, RH
15.
16.
17.
18.
19.
20.
21.
22.
Pin, Top Link 3/4 X 4-1/2" LG
Pin Lynch 7/16 X 5/8"
1
1
2
1
1
1
1
1
51280
51276
51281
51316
51367
51310
51483
51481
1
3
Decal, 540PTODanger
Driveshaft, 540 PTO Chipper
Spring, Ext. 3/4" OD
1
Bearing, 2 BLT FLG 1-1/2" Bore
Pulley, Idler 5" X 2.50"
Sheave, 3B13.6SK
Sheave, 3B4.8SD
1
1
Bearing, 1-3/4 4 Bolt Flange
Weldment, LeftBearingBracket
Weldment, LowerBeltGuard
2
1
10.
11.
51224
51315
BushingSK1.5
1
Belt, BX 64 (Matched Set of 3)
PN-51210 (Rev. 7/98)
28
H I P P E R
B
A S E
A
S S E M B L Y
26. 51419
27. 51480
28. 51490
29. 51503
30. 51504
Description
Qty.
/2" Flat ZP (56PC/LB)
1/2" Center Lock
25
1
/8"FLT ZP-140PC/LB
/8" NYL Insert, NE, ZP
Bolt, 5/16 X 1" GR5 HHCS NC ZP
Washer, 5/16" FLT ZP (195PC/#)
Locknut, 5/16" NYL, NC, TYP NE, ZP
Bolt, CARR 1/2 X 1-1/2" GR5, ZP
Bolt, CARR 1/2 X 1-1/2" GR5 ZP
Bolt, 3/8 X 3-1/4" HXHD GR5 ZP
DangerDecal
21
26
10
19
5
38. 14562
JointShieldWeldment
Weldment,IdlerArm
1
1
39.
40. 71061
41. 839
4378
Cover, HoseAccess
1
Shield, Shaft
1
2
Plate, Spring Anchor
1
42. 12735
43. 12169
44. 51361
45. 58777
46. 15131
2
31.
32.
33.
3379
3699
1637
Bolt 1/2 X 1-1/2 GR5 Hex Capsw Zp
Bolt, 1/2 X 2 GR5 Hex Capscrew Zp
Bolt, 1/2 X 3-1/2 GR5 HCS ZP
9
1
10
1
1
Wldmt,PickupSprocket
1
Screw, 5/16" x 5/8" Cup PT
PN-51210 (Rev. 7/98)
29
1
H
Y D R A U L I C
Hydraul
PN-51210 (Re
30
31
H
Y D R A U L I C
F
E E D
P
A R T S
L
I S T
HydraulicFeedPartsList
No. Part No.
1. 51476
2. 51477
3. 51479
4. 51478
5. 51486
6. 51487
7. 51256
8. 51522
Description
Weldment, RollerSupport
Weldment, TopGrabRoller
Weldment, Roller Slide
Bearing, Roller Slide
Weldment, TopRollerCover
Shield, Coupler
Qty.
1
1
1
2
1
1
1
1
1
1
1
2
1
1
1
1
2
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
No. Part No.
Description
Qty.
1
42.
43.
44.
45.
46.
47.
48.
49.
50.
51.
52.
53.
54.
55.
56.
57.
58.
59.
60.
61.
62.
63.
64.
65.
66.
67.
68.
69.
70.
71.
72.
73.
74.
75.
76.
77.
78.
79.
80.
81.
82.
83.
84.
85.
51369
51373
1686
Spring, Drift Cutter 1-1/4"LG
Decal, Danger
2
Cotter Pin, 1/16 X 3/4" Steel ZP
Screw, #10 X 3/4" Phillips
1
35709
51252
5337
2
Locknut, #10NYLInsertTPNEZP
Bolt, 1/4 X 1/2" HCS G5 ZP
Bolt, 1/2" x 1-3/4" Carriage GR5 ZP
Locknut, 5/16" NYL, NC, TYP NE, ZP
2
4
Coupler 1-1/4" Shaft
Weldment, ControlPivot
Weldment,ControlArm
Weldment,CableAnchor
Weldment, FeedControlLever
Spacer, Idler Pivot
51248
71061
51591
51589
24576
51239
21757
28093
3632
6
9
9.
51493
Washer, 5/16" SAE FLT ZP (195PC/#) 11
10. 51494
11. 51495
12. 51393
13. 51496
14. 51497
15. 51498
Clip, Hairpin
2
4
8
Bolt, 1/2 X 1-3/4" GR5 Hex CPS ZP
Bolt, Carr 3/8 X 1-1/ 2" GR5 NC ZP
Strip, Control Tie Rod
Weldment,PumpControlArm
Angle, CableAttachment
Bracket,PumpMount
Strap Reservoir
Washer, 3/8" SAE FLT ZP-140 PC/LB 41
Locknut, 3/8" NYL Insert, NE, ZP
Washer, 5/8" SAE Flat ZP(37PC/LB)
Decal, Oil Level
36
8
16.
51485
58780
58781
14562
6697
1
17. 51492
18. 51491
19. 51510
20. 51240
21. 51507
22. 51432
23. 51304
24. 51317
51262
Decal, Oil
1
Weldment, ReservoirSupport
Cover, Reservoir Base
Bolt, 5/16" x 2" GR5 HCS ZP
Assy, ChipperChute(Inc. #43)
Spacer, 0.75X0.620
Sheave, 1B5.2SDS
Pump, Hydrostatic
Bolt, 5/16 X 1" GR5 HHCS NC ZP
Bolt, 3/8 X 1" CRG
2
5
839
Bolt, 3/8 X 1" GR5 Hex Capscrew ZP 12
3597
Pin, 1/8 X 1" Cotter
Nut, 3/8" Hex NC ZP
2
1
835
51236
12169
3231
Spring, Extension
2
Bolt, 3/8 X 1-1/4" Hex Hd
Bolt 3/8 X 2" GR5 Hex Capscrew ZP
Bolt, 1/2 X 2" GR5 Hex Capscrew ZP
Nut, 1/2" Center Locknut ZP
Washer, 1/2" Flat, ZP, (26PCS/LB)
Hinge, Extension
2
Kit Hydrostatic Pump Seal
Motor, 45Cu. In. Hydraulic
Kit White Motor Seal
Valve, Crossover Relief
Kit, Relief Cartridge Seal
Kit, 2000 PSI Relief Shim
Filter, Spin-on
2
25. 51318
51263
3699
4
765
12
12
1
26. 51319
51271
854
51513
63013
51264
3912
51287
Key, 5/16" Sq X 2
2
27. 51320
28. 51321
29. 51306
30. 51330
31. 51237
32. 51254
33. 51380
34. 51329
35. 51245
36. 51242
37. 51768
38. 51246
39. 51238
40. 51365
41. 51366
Key,5mmSqX25mm
1
Tank, Oil Reservoir
Key, 3/8 X 1/4"
1
Sheave, 1B3.6SH
51294
51302
51325
51392
51391
51300
51265
51327
51328
51324
51258
51512
Adapter Oring to Flare
2
Bushing, 1.75SDS
Adapter Oring to Flare
6
Bushing,15mmSH
Reducer Bushing 3/4 X 1/2" NPT
Elbow, 90Deg, 2024-8-6
Elbow, 90Deg, 2062-6-6
HydHSAssy2X/-10MJICSWVL
Eyebolt, 1/2 x 2
2
Bearing, 1-1/4" Dia. 2 Bolt Flng.
Bearing, Side Flng. Mount, 5/8"
Cable, Hydrostat Control
Cable Pivot Pin
2
1
2
4
ClevisAssembly
Hyd. HoseAssy, NoneX-6JIC
Hyd. HoseAssy. 2X-6JIC
Adapter, Oring to Flare
2
Cable ClampShim
1
Cable Clamp
1
Belt, BX43
Hy-Hose-Asy-10FM90JICSW/-10FM
Tray, Chute Extension
2
Detent Ball
1
Detent Spring
PN-51210 (Rev. 7/98)
32
S
P E C I F I C A T I O N S
Specifications
Model8000
87"
Model8100
87"
Height(todischarge)
FrameWidth
FrameLength
OverallSize
38"
38"
36"
36"
45" x 47" x 90"
32" x 36"
0.25"+0.38"Steel
SelfFeed
Blower
45" x 47" x 90"
32" x 36"
0.25"+0.38"Steel
Hydraulic
Blower
ChuteSize
FrameMaterial
FeedSystem
Discharge
8"
8"
MaximumChipperCapacity(dia.)
ChipperBladeQty. (*=toolsteel)
RotorSpeed
4ToolSteel
1500RPM
4ToolSteel
1500RPM
30" Dia. x 1.25"
275lbs.
30" Dia. x 1.25"
275lbs.
RotorSize
RotorWeight
1.75"
1.75"
RotorShaftDiameter
Belt
Belt
DriveType
BX64, (3)
BX64, (3)
Belt Size (qty.)
SplineSize
1.375Diameter(6Spl)
1.375Diameter(6Spl)
TopTube
TopTube
Discharge
8"Diameter
8"Diameter
DischargeOpening
Specificationsaresubjecttochangebecauseofdesignmodifications.
PN-51210 (Rev. 7/98)
33
Warranty
Woods warrants each new Woods products to be free from defects in material and
workmanship. This warranty is applicable only for the normal service life expectancy of the
machine or components, not to exceed twelve consecutive months from the date of delivery
of the new Woods product to the original purchaser.
Genuine Woods replacement parts and components will be warranted for 90 days from date
of purchase, or the remainder of the original equipment warranty period, whichever is longer.
Under no circumstances will it cover any merchandise or components thereof, which, in the
opinion of the company, has been subjected to negligent handling, misuse, alteration, an
accident, or if repairs have been made with parts other than those obtainable through Woods.
The company in no way warrants engines, batteries, tires or other trade accessories since
these items are warranted separately by their respective manufacturers.
Our obligation under this warranty shall be limited to repairing or replacing, free of charge to
the original purchaser, any part that in our judgement shall show evidence of such defect,
provided further that such part shall be returned within thirty (30) days from date of failure to
Woods, routed through the dealer and distributor from whom the purchase was made,
transportation charges prepaid.
This warranty shall not be interpreted to render us liable for injury or damages of any kind or
nature to person or property. This warranty does not extend to loss of crops, loss because of
delay in harvesting, or nay expense or loss incurred for labor, supplies, substitute machinery,
rental or for any other reason.
Except as set forth above, WOODS SHALL HAVE NO OBLIGATION OR LIABILITY OF
ANY KIND ON ACCOUNT OF ANY OF ITS EQUIPMENT AND SHALL NOT BE LIABLE
FOR SPECIAL OR CONSEQUENTIAL DAMAGES. WOODS MAKES NO OTHER
WARRANTY, EXPRESS OR IMPLIED, AND, SPECIFICALLY, WOODS DISCLAIMS ANY
IMPLIED WARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. SOME STATE OR PROVINCES DO NOT PERMIT LIMITATIONS OR
EXCLUSIONS OF IMPLIED WARRANTIES OR INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE LIMITATIONS OR EXCLUSIONS IN THIS WARRANTY MAY NOT
APPLY.
This warranty is subject to any existing conditions of supply which may directly affect our
ability to obtain materials or manufacture replacement parts.
Woods reserves the right to make improvements in design or changes in specifications at any
time, without incurring any obligations to owners of units previously sold.
No one is authorized to alter, modify, or enlarge this warranty nor the exclusions, limitations
and reservations.
PN-51210 (Rev. 7/98)
HEALTHWARNING
GASOLINE, DIESEL, AND
OTHER PETROLEUM PRODUCTS
Harmful or fatal if swallowed.
Long-term exposure to vapors has caused cancer in
laboratory animals.
• Avoid prolonged breathing of vapors.
• Keep face away from nozzle and gas tank/container
opening.
• Never siphon by mouth.
Failure to use caution may cause serious injury or illness.
WARNING
CHEMICALS KNOWN TO THE STATE OF CALIFOR-
NIA TO CAUSE CANCER, BIRTH DEFECTS, OR
OTHER REPRODUCTIVE HARM ARE FOUND IN
GASOLINE, DIESEL, CRUDE OIL, AND MANY OTHER
PETROLEUM PRODUCTS AND THEIR VAPORS, OR
RESULT FROM THEIR USE.
READ AND FOLLOW LABEL DIRECTIONS AND USE
CARE WHEN HANDLING OR USING ALL PETRO-
LEUM PRODUCTS.
ENGINE EXHAUST FROM THIS PRODUCT CON-
TAINS CHEMICALS KNOWN TO THE STATE OF CALI-
FORNIA TO CAUSE CANCER, BIRTH DEFECTS, OR
OTHER REPRODUCTIVE HARM.
|